I just purchased a brand new refrigerator from Whirpool and after 2 weeks been delivered I started having a lot of issues. They sent a technician twice to get it FIX but Im still having the same problem. And they dont want to replace the unit. They want to keep sending technicians to make the same repairs. Its a NIGHTMARE!! Please do yourself a big favor and buy a different brand. I dont recommend!! By the way this appliances are made in MEXICO!!

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

After months of careful research and comparison, I finally bought a pricey (over $2K) Whirlpool refrigerator with a bottom freezer and French doors with water dispenser on top. I really did not want any fancy features, just narrow doors because of my small kitchen, and a fridge on top because of my back pain. Since the date of purchase in May, 2014, I have had 4 service calls. The first was covered under warranty, but no cause of the sheet of ice collection and underside water leakage was identified; I did, however, receive a somewhat patronizing lecture on the importance of thorough reading and comprehension of the owners manual, and a statement that most of my service calls are for customer education. A follow-up service call, a few weeks later and also covered under warranty, identified the cause of the ice collection and water leakage: a faulty duck bill little piece of plastic in the drainage system that is a problem well known to Whirlpool. In mid-June of 2015, the ice maker had to be replaced, to the tune of $360.00. Today, I had a service call ($103.00) and received an estimate of $405.50 to replace the broken freezer drawer slides, which prevent the freezer drawer from fully closing. I will be applying that $405.50 to the purchase of the simplest model, non-Whirlpool refrigerator available, and have the Whirlpool hauled away. Besides the problems noted above, the center of the refrigerator freezes the food, while the freezer compartment arbitrarily defrosts. There are alarm icons that go from blue to red to alert you of the need to replace the (expensive) ice and water filter, refrigerator air filter and crisper freshener. Alarm bells ring to inform you that the doors have been open too long, but nothing alerts you to the fact that the freezer door is not completely shut, or that the freezer has gone into defrost mode because someone inadvertently brushed up against the control panel and changed the settings, or that water is pouring freely out from underneath the appliance. I have had to change my buying habits because fridge holds at least 15% less food, even though it is the same cubic footage as my previous (top freezer) one. Freezer contents easily slip down behind the top freezer drawer and jam the door open. I have to take most frozen boxed items out of their original containers and pack them flat in freezer bags to get enough storage. Some tall bottles do not fit anywhere in the refrigerator compartment, and have to get put in sideways. Even in the absence of mechanical problems, using this refrigerator is like packing and unpacking a suitcase many times a day. While Whirlpool customer service personnel were not overtly rude, there were dismissive and condescending overtones in some of the questions and directives I received from them, and another insinuation that service calls would not be covered under warranty if they end up being for the purpose of customer education. The extended wait (7+ days) for appointments with a Whirlpool-certified appliance repair company, along with the customer education exclusion, were absolute deterrents to the purchase of the extended warranty. Besides my personal disappointment and disgust with the purchase of this appliance, I am sad to see that the Whirlpool brand has slipped so far in product design, quality and customer support.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

Oct 14th I walked down to our basement to find it flooded. Turns out the leak came from the solenoid that controls the water feed to our Whirlpool Gold Series refrigerator. Now, some $28,000 in damages later - floors/cabinets/walls/electronics - you name it. The repair company said that they replace these units a lot as it is simply a faulty design and Whirlpool knows this as this part is very difficult to obtain - too much demand. Well aside from the cost, the inconvenience, and the rise in our insurance rates the repair person said there was a good chance of the new part failing as well - it just cant take the water pressure as it is just cheap plastic. My advice - stay away from Whirlpool!

We purchased a Whirlpool Cabrio Washer (Mod #WTW7300XW1) and Dryer in 2011. Ever since we have had the washer it has eaten clothing, towels, sheets etc. It now has a main bearing that is so noisy that we have to close the door to the laundry room to be able to hear in the rest of the house. Also the sealed tank around the drum is now leaking. We invested close to $1000.00 in this washer and in my opinion it is a piece of junk. The washer repairman told me that he has had 3 (three) other Cabrios with the same problem in the last month, but Whirlpool says that there is nothing they can do as they have had no issues with this problem. Last Whirlpool product that I will buy.

I like the experience of the microwave. Especially because it’s mounted in the wall and easily accessible. User-friendly, easy to use, and pretty self-explanatory. It’s very easy to clean which is something my wife really loves knowing we both are working professionals.

What a disaster! Within one year we had to repair the stove twice, the dishwasher and the fridge! Almost three years later, we are experiencing problems with two burners and with the fridge! The company does not stand behind its products. Avoid them.

I have bought a top load 6.2kg washing machine 3 months back. But now almost all the plastic parts are having a cracks. When I asked for replacement they said plastic parts are not covered in warranty.

My Whirpool refrigerator model # WRF990SLAM01 was 14 months old (2 months past the new product warranty) when we started having issues with multiple areas. The ice machine stopped making ice and started dripping from the dispenser and the freezer stopped freezing food. I called and was told to purchase an extended warranty which cost me $375.00. The service tech has been to my house 12 times over the last 9 months. They have replaced multiple parts and even started replacing parts a second time. I was instructed by the service tech to call and request a replacement fridge. Whirlpool customer service told me that it would have to be considered a lemon before they replaced the product. I was told that would require each component to be replaced 3 times. I would need to take off work 27 more times for the repairs!!! The service tech came out one more time and he said there was nothing else he could do. I called again to complain and even wrote to Whirlpool corporation (though they never called me back at my request). After much complaining, which I do not normally do, they have decided to replace the unit. BUT I have to pay and additional $476.29 for them to replace this unit!!! I feel like I was totally raked over the coals from this company. I will never buy another Whirlpool product again and I recommend you do not either.

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

My washer is a top load, energy and water efficient model. I am amazed at how little water it uses and how well it cleans. I do have two issues, the capacity looks huge but it will not take a queen size and double sheet set in the same load. It unbalances and then cant seem to get going again. The other issue is that you cant pause the wash and adjust things, you have to cancel and start over.

I have Whirlpool 40 gallon heater 5 years ago. The pilot light went out and I replaced the parts. This has happened three times and I have replaced the entire thermocouple assembly three times. The last time, the parts came straight from Whirlpool. This time, the pilot light will not stay lit. I am on my way to buy another hot water heater for my family because I have had enough.

I chose Whirlpool first then my machine became of I wanted a front loading machine with a larger tub. I wanted to be able to wash anything without hesitation. I truly love my wash and dryer. This set is the first set I have ever bought brand new.

The Whirlpool I purchased has been the worst ever! Nothing comes clean even when I hand wash everything first and never has even from the beginning. I will never purchase a Whirlpool again. Now the machine wont drain I have gone through all the recommended steps for cleaning. The Whirlpool stove is almost as bad!

We purchased a Whirlpool stove a year and half ago. We were cooking and kept hearing (tick, tick, tick) noises. Couldnt figure out what it was. After removing the pot there was an area of 2x4 inches that had melted in. Not sure where the glass went. But it looked like a chip but on the surface.

Had the fridge 5 1/2 years. Freezer quit working was told by 2 different repairmen it would cost $800 to repair. Called Whirlpool, was on hold 45 minutes, literally, both times I called. They could not help me. Called the corporate complaint line. The man I talked to was such a smart **! I finally said I cannot believe you are talking to me like this, I have bought Whirlpool for 35 years. He backed off slightly. Still couldnt help me. BTW, I LOVE my new Samsung refrigerator! Will NEVER buy Whirlpool again.

Glad to know we are not alone in our disappointment with our Whirlpool French door refrigerator, but I am wondering what and when Whirlpool is going to do something about this. What a blow to their reputation. Goes to show things are not made as they used to be. We purchased our Whirlpool Gold French door (bottom freezer) in August of 2010. Here we are October 2012 and this is the third time it has stopped working. We have lost food, weekends waiting for repair people and cleaning up messes, and money. Same problem as others are reporting - the electronic board and controls. I just spent my Friday evening on the phone with Whirlpool, first explaining the problem to no result then waiting for a manager to call me back. Who (guess what?) never called. I finally called them and got the same script as the rest of you. It is outside the manufacturer warranty. Really, that is what you are giving me? Plus they will only look at it if we have a Whirlpool repair person come see it. When can they come? In 4 days! Ha, not likely. I am not giving this company another cent. We spent almost $2,000 on this fridge, all we are getting is 2, 3, 5 years? What a shame. We are fortunate enough to have had some space in our garage beer fridge for what I can save of the food. Our 7 years old, $300 Moffat fridge has been working like a charm. We will never again fall for the looks of a Whirlpool, let alone purchase another one of their appliances.

The oven works well. My complaint is that the glass door is very difficult to clean. Some kind of liquid got in between the panels and I cannot clean the glass without removing the oven door. Im afraid to remove the door as I may not be able to get it back on the oven. I have dirty glass I cant clean and that makes me unhappy. Otherwise the oven works just fine.

Whirlpool Duet washing machine model WFW9500TW03 - Just after the first year of owning this machine, the metal hinge to the door cracked and the door didnt shut properly. It was replaced. After a couple of years, the bearings and drum of this machine failed. The cost for parts and repair were as much as the machine new. After repairs, the machine never ran quietly again. I have called for repair a second time for the same issue and he has confirmed that its the bearings again causing the drum to dislocate and hence, break the belt that I now need to replace. My problem is with Whirlpool for its defective metal in its machines (many complaints on the internet will confirm this). I believe there are enough consumers out there to file a class action lawsuit.

The board manufacturer number W10312659 went out. They replaced the board. The oven was 6 months old, luckily was still under warranty. We didnt purchase a extended one because mostly it had a good name and brand. Well after a year and a half the board went out again. It gives error code H5P which there is no error H5P. So the boards out. It is very costly and thats with you doing your own service. Never will I buy another Whirlpool stove.

A few weeks after we bought it, the washer was already having issues spinning out, and the clothes would have to go through another rinse and spin cycle. A bout a year and a half in and I had to replace the pump because it stopped draining. Even carefully loading the machine, and at least two or three times a week it would not spin out. Two weeks ago it stopped agitating actually performing washing action and spinning out all together. Last night I replaced the actuator which controls the speed or lack thereof in the spin. Still nothing. Ive reset it multiple times, still nothing. At least the clothes are getting wet. At tax return time I am replacing this piece if garbage and I will never get another whirlpool, or Maytag washer again because from what I have been told by dealers and repair men; they are all garbage.

It shows handprints, smudges, the door swings open and slams into stove. I did purchase extended warranty which I intend to pursue, not enough space, door issue, junk. Dissatisfied, dislike, low quality - that should say enough.

I bought a Whirlpool refrigerator in 2007 from a recommendation from my repairman. He told me that most refrigerators last about five years. I cant believe after five years I will have to buy another refrigerator. I know someone that has a refrigerator that is 50 years old. Cant any refrigerator makers make any appliances that last? With all the technology we have nowadays, it seems like you could. You just want the public to spend more money on repairs or a appliances. Hope you buy the product you sell! Looking forward for a reply.

We have all Whirlpool appliances in our home as well as our rental property. All of the appliances are of great quality and perform extremely well. The dishwashers are both heavy duty and do a tremendous job of cleaning the dishes. Both have a jet dry feature which is extremely important to us.

I love my Whirlpool. Were a family of 3 with a pet dog. Its handle one childs work uniforms and the others sports uniforms (yuck). And then theres my work/weekend clothes. Its very reliable and it gets the job done. We have no complaints.

My three month old $2,000 combination microwave-oven works a fine, its the just the details that stink. For example: There is no way to turn off the turntable. Yes! a crappy $40 microwave can do this, but not this one. Liquid got into the middle of the door window. You cant open it up to clean, they want to send a technician to clean that up so you can actually see through the window. How much? $150. How was it possible that Whirlpool did not adequately seal the glass? They dont care, and dont care about how it looks.

We purchased the Whirlpool Cabrio washer and dryer duet exclusive to Lowe’s in June 2011. I was immediately dissatisfied and went to Lowe’s. They told me I only had 7 days to return it. They dispatched a service man and he said it was working as it was intended to but I would never be satisfied. If I had dirty clothes from farming, construction, or mining, I should forget about it.” The washer is an eco-friendly model and all the clothes do not get wet. It wrings them out very tight and everything needs to be dried or ironed to get rid of the wrinkles. After 6 visits and lots of stress, I am returning the washer to Lowe’s and they will replace it with a different model. It definitely will not be a Whirlpool. I am very disappointed in the service and response I received from Lowes.

Best microwave for your money. It is very quiet and easy to use. This microwave is very sharp looking and comes with all the bells and whistles that you need. I like the potato setting. You put your potatoes in and it will ask you some stuff and you press the button.

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...

Purchased a new Whirlpool water heater from Lowes. Two days into the reset switch kept tripping, Whirlpool wanted me to wait for someone to repair it. Lowes exchanged it for me. When I called Whirlpool service myself, Jessie was in technical support could have careless about my business and was dismissive about any issues or concerns I was having. This will be my last Whirlpool product ever.

Model WMH1164XWS-3 Microwave - I purchased a brand new home in 2012 with all stainless appliances, within 3-5 months the outside door handle where it attaches at top and bottom of microwave has chipped, so that the screws are shown. I havent had the time to look up the replacement part until just now. Very disappointed in the amount of money a handle only cost.

I also have a side-by-side Whirlpool Gold Fridge purchased from Lowes Retail Store, and I paid $1,480.00 for it. It is now 4 years old and I just noticed large cracks on right, inside part of the fridge. I called Whirlpool and got a runaround. Some lame guy said, Sorry, nothing we can do for you.When are people going to stand up for their rights and fight for their bucks? They havent heard the last of me but I will put this on the back of my truck with a nice sign on it for thousands to see. If anyone else has had this problem email me at ** and lets talk. I will never buy any Whirlpool items ever, ever again! Buyers beware! I also hold Lowes Retail Store responsible for this. They should research and stand behind what they sell, they are no better than Whirlpool!

I absolutely hate this washing machine. When I bought it a couple of years ago I thought it would be great for large items... NOT! It leaves white residue on dark colors but the MOST important issue is going off balance. The lid stays locked and you have to start the cycle from the beginning... What a waste!!! Never again will I get a Whirlpool.

We bought a Cabrio washer model #WTW7300DW0 and are very unhappy. The clothes come out of the washer dirty, with chunks of soap, (yes we are using HE detergent) and patches of lint on them. The low water design is a joke. The clothes on the top of the load never get into the water. The lid needed repair from the first day we bought it. We have tried all the water settings and the clothes on the top barely move. Why hasnt Whirlpool figured out that this design is just not working? Our three month old washer is headed out of our house one way or another! Notice we didnt give it any stars!

On 11-29-2014 we were washing our laundry and our whirlpool washing machine started making a really loud noise so I went to investigate the problem. I open the bottom part of the washer to find out that the whole cement block to balance the drum was on the floor of the washer so I called the 1800 number on the machine and no one at whirlpool corporation wanted to even help. No one said sorry. No one said Let me see if I can help. No one. Every one I talked to they cant help at all. No one apologized once about the poor product that whirlpool sells and the defect that their products has. My washer is one year and one month old. So I can say truly with confidence that whirlpool product are the worst in the world plus their customer service even more. It is very sad after we paid all kind of money for our washer now I have to buy another one after one year and one month. Very bad customer service.

I purchased the original Whirlpool water heater from Lowes in April 2008 for $372, and an installation charge of $443, grand total - $815. In February 2012 the tank leaked profusely, enough to ruin a section of hardwood floor in the room behind the garage where it was installed. Whirlpool provided me with return authorization, and Lowes provided me with a replacement water heater. So far so good. Since the original installation was done through Lowes, the replacement had to be as well, according to Whirlpool, but now they charged $500 with tax to install the replacement water heater! Grand total now is $1315. Fast forward to May, 2014 and the replacement water heater, just barely 2 years old, shuts off with a code of Bad gas control valve/thermostat. I call Whirlpool and an extremely rude 20-something staffer tells me the unit is out of warranty by one month! The replacement unit has no warranty at all - nada - only the original one does... Is this unbelievable or what?! BUT, they would be glad to send me the replacement of the defective part for $200 PLUS overnight shipping charges, and I would be responsible for all labor charges to install it. Had I opted for this my original $372 water heater would have wound up costing me in the neighborhood of $1800!! I told her in no uncertain terms what she could do with the repair part, and now I am going to go shopping for a water heater that will last me more than 2-4 years, and you can bet it wont be a Whirlpool, and it wont come from Lowes.

Sole owner/operator for 6 years using same products that came packed with dishwasher. Bottom rack has simply crumbled away, prong by prong at first and now large sections. Inferior quality of coating and metal used for the forms, means it wont withstand the daily use for which a dishwasher is intended. Worst quality control ever!!

Chris from Whirlpool contacted me the same day that I filed my complaint. He offered to replace our water heater at no charge. We will pick up our new water heater this weekend and install it. Hopefully, it is designed better than our current water heater.

Need to arrange shelves for better storage!!! Ive not had any major problems with it so far!!! I need the rubber seals on the freezer and refrigerator door replaced!!! Other than that its alright!!! Im hoping it lasts for a long time!!!! On disability and be hard to replace!!!

I purchased a water heater Model # UG1H50400TBN, Serial # 0913T400920, from Lowes in Corona, CA. 05/07/2009 for $528 plus tax. I have replaced the following parts: 02/10/2010 Thermostat Valve, 07/23/2010 Thermostat Valve (2nd time), 08/10/2010 Burner assembly, 02/10/2011 Thermocouple, 02/17/2011 Thermostat Valve (3rd time), 12/17/2014 Thermocouple (2nd time) and 03/20/2015 Burner assembly (2nd time).Today I called WHIRLPOOL Customer service (877) 817-6750 because my water heater water is warm. I told the tech support agent that the pilot light was on so we agreed that it was the thermostat valve AGAIN. He wanted $30 for overnight delivery and I refused to pay. Now I have to go out and buy this part because Whirlpool like the Banks is too big to fail and they have license to RIP-OFF the consumer without penalties. Whirlpool has all of information and they can verify everything I wrote here just by the serial number.

I am questioning my loyalty because the last two Whirlpool fridges have been repair prone, and have bad design issues for ice dispensing. The dispenser door doesn’t close reliably and lets the ice maker warm up and melts the ice. This supports my rating.

Every washer Ive ever had has just a spin. Why dont these new washers? If the washer is un-level why would you add more water? They need a spin cycle to drain the water out of it. No more rinse and spin just a spin. Very aggravated.

The home I bought a few years ago, had brand new Whirlpool appliances. The oven and range, work great, although it does take my oven seems like a long time to get to temperature. The size of the oven is great, has plenty of room to cook lots and/or large amounts. The range, works really good too. Its a glass top range. The glass is very durable, I find it does not scratch easily. Cleans up well by just using a good glass top cleaner. I do have one of the burners, does make a little noise if used but 4 years in, no issues out of the range or oven.

We purchased our Duet in July 2010. It worked great until two weeks ago when the washer sounded like a 40-year-old washer. The bearing sounds like an extremely high-pitched “wrr”. We can hear it in the back of the house. I looked online to get parts and noticed that you cannot replace the bearing. You must replace the entire rear drum ($358.00). This does not include the labor. I talked with a technician, and they said the whole drum must be removed, not a one-man job, and to take the whole thing apart. Now, theres no price for installation. Lets go low ($200.00). Probably more. I cannot get a price nailed down without a visit. Now add those together ($558.00), I could put almost $600.00 into a washer that this could happen to in another 2 years. Wow.We had a washer that lasted us 15 years without any parts. Is there anything that you can do to help me? This is totally outrageous. Please help. Thank you. This was part of my chat to Whirlpool. Whirlpools response was I understand your problem but cannot help you. It is out of warranty. No help, no discount, nothing. I will and have all my friends never to purchase Whirlpool. This is from a so-called American company. Im very disappointed.

This is a comment for the person with the ice maker problem. I have a side-by-side, in-door ice dispenser that clogs up. First sign of problem is either the ice wont come out or it comes out crushed. What happens is frost builds up in the path the ice takes at a couple of different points. The only solution I have found is as soon as the problem starts I turn off the ice maker using the switch on the inside of the freezer. Then let it empty with normal use (if you wait too long youve increased your problems). The release button for the ice bin has frozen by now so you cant just lift it out. The bin needs to be empty. When it is empty, work the bin loose and take it out. Youll find that frost and maybe cubes have collected, frozen and blocked the passage. Be sure to turn the ice bin on its side and spray water into the undercarriage to melt and remove all the ice build up there. I use a hot sponge to melt the frost in the ice tube and then dry everything. This gets messy so be prepared to have water on the floor. Dry the ice bin and reinstall it. Ice cubes will be ready to drop from the ice maker so it wont be long until you have plenty. I live in Florida with high humidity so need to go through this process about once a month. Its a pain, but now it is just part of owning this unit. Good luck and hope this helps.

I purchased Whirlpool top loading washing machine model # WTW57ESVW less than 2 years ago. It stopped working yesterday. I had a trusted professional repairman evaluate it today. The motor needs to be replaced after less than 2 years?! The customer service reps basically said sorry. I should have purchased the extended warranty. Is it not reasonable to trust that a Whirlpool washing machine motor should last more than 2 years.I am very unhappy and very angry that Whirlpool will not stand behind their product. The last customer service rep I spoke to suggested she could send one of their repairmen and replace the motor at a cost to me of $299.00. So, after less than 2 years, I am offered an amount to pay of about half the cost I paid less than 2 years ago for the brand new washing machine. My home is full of Whirlpool appliances. I have been a good and loyal customer for over 30 years. I am very angry and upset with Whirlpool. Please explain to me why it is not reasonable for me to trust and believe that a Whirlpool top loading machine that is well cared for and not abused in any fashion should last longer than 2 years? Is this being a loyal Whirlpool customer gets you, I should have purchased the extended warranty”? We are talking about a motor here, not a fabric or bleach dispenser that breaks. Although, those parts should not break either, there is a big difference from something like that and a motor. Please contact me as soon as possible at either number listed above. Thank you.

After 2 years the motherboard failed on my Top load Cabrio washer. We had to spend $300.00 dollars to get fixed. When we called Whirlpool to see what they would do about it, they actually offered to sell us the board for $345.00 dollars and a 1 year warranty on the board. They actually wanted us to pay more from them than a local repair service. DO NOT BUY THIS MACHINE OR ANY OTHER WHIRLPOOL PRODUCTS. Also does anyone know of any class action lawsuits surrounding their obvious use of defective parts?

We purchased this combo from Lowes; checked my account and saw we were double charged! Got the charge adjusted; jeez. Bought this size to do comforters and large loads, but nothing large gets completely wet. Our clothes started to mildew as Affresh does not work. Im allergic to mildew and got headaches. The mechanic said this mildew is because all the action is under the basin and you dont want to see how black it is under there. It began to leak as buildup went into the bleach dispenser, and it turned black.He said to run a gallon of white vinegar in the clean cycle once a month, and this did work. I did a clean out with Castile peppermint soap, several white vinegar treatments, and got rid of the mildew and the (clog related) leak. I now use Mollys Suds powder. I was shocked to read on the Mollys site that mfg does not have to list all the terrible ingredients in commercial detergent, which is not helping you or the machine.

We have had our Whirlpool range for probably 20 years. We have never had any issues or problems with it. Our washer and dryer are both Whirlpool too. I would recommend this brand 100%! I think this is the brand that my mom always had too. Their products are very well made and last forever (it seems like they do!).

Whirlpool 5.3 Cabrio. This was the worst experience ever with a washing machine. My first cabrio did not work at all. My second one gave out after 2 weeks. It would not spin. I got my money back and would not recommend this washer.

We bought the Whirlpool Gold series side-by-side about 2 years ago with an ice maker in the door and with this design, the ice bucket is on the inside of the door, which we thought was a very clever design, taking up less freezer space. Well, to remove the ice bucket, we had to use a blow dryer because even though you press the button which is supposed to disengage the bucket from the door, it has always been frozen onto the base.Then we started having issues of water leaking from the ice maker. It turns out, that the lever that controls the chute was broken. We called a certified Whirlpool technician to come out to fix the ice maker dispenser lever. Well as it turns out, it cannot be fixed. It is a sealed in the door unit and to fix it, we have to replace the door, a repair estimate for door and labor is approximately $800. That is absurd.I contacted Whirlpool and was told that my refrigerator is out of warranty and that there is not an option to repair the dispenser. There is nothing we can do. I said that according to the repairman, we are not the first to report this problem. When I contacted Whirlpool I was told there is no recall for this item. We purchased the Whirlpool based on the reputation that it has had in the past and the good product we have in a Maytag (which is associated with Whirlpool) dishwasher. Well, never again are we going to purchase a Whirlpool or any of its subsidiaries products. I have read so many unhappy customers here that I cannot believe that Whirlpool continues to make such inferior products or designs.

This refrigerator is less than 1 yr. Old and this repair will be the FOURTH. The severe lack of craftsmanship and customer service is shocking! Most states do not have lemon laws for appliances, however something needs to be done to compensate me for THE TIME and inconvenience this caused my family. I needed to purchase a second compact refrigerator because I knew that it would break down again!

My fridge is only 8 months old and stopped working about 5 weeks ago. They have sent repair techs out 5 times, replaced the compressor, condenser, some fan thing and evaporator. It worked for 2 days then the compressor started leaking again. Ive lost 2 refrigerator full of groceries. It damaged my floor. I was unable to have family over for Christmas and Ive been using a mini fridge. The Whirlpool customer service people have been no help and some have been very rude. I have no idea when this will ever be fixed. There is no way I would ever buy any appliance from Whirlpool again. Terrible experience.

My dishwasher is just under 3 years old. It has never cleaned well and doesnt dry well at all. I have replaced parts for the top rail 4x. I have 4 other Wp appliances and none are good. The plastic parts in these appliances are beyond cheap and yet they have no problem selling them at a premium. And they also do not stand by their products. Why in the world would you need an extended warranty to get you through 3 years? In other words they make crap and want you to pay them because their stuff is crap... Im done with Whirlpool.

I just purchased a new stove after using my old one for 15 years with the same great quality. Its the brand I will purchase when I have my retirement home built next year and leave my new one in the home for my son so he wont have to buy one for 15/20 years.

I had a kitchen fire in 1999. All appliances were replaced with Stainless Steel Whirlpool. My old fridge was an 18 y.o. Whirlpool and still works fine in the garage. My old above range microwave was 12 y.o. and worked fine, I should have kept it. I had to replace my new Whirlpool Microwave after 4 years and 4 repairs. (Main Power Diode kept failing). Now my Whirlpool Gold fridge is not defrosting, even the freezer light switch is frozen. This French door freezer also seems to have less capacity than my old upright freezer. The retailer seemed sympathetic and pathetic. They would not budge on repairs. I told the contractor that did the rehab on my house what happened, he said he would stay away from Whirlpool and that retailer.

I chose this dishwasher with stainless steel exterior to match other appliances in the kitchen. It functions very well and has for years. Very easy to keep clean. The interior shows no wear and the racks provided make it easy to arrange the dishes and silverware.

Oh my goodness, are these people right with the Whirlpool Ranges. I moved and put in the appliance # to get what I had from Whirlpool. What a piece of crap I got in a range and refrigerator. Never had appliances that looked so pathetic. You cant clean the outsides or the insides. Outsides nothing but streaks never look shiny, I really do doubt they are even close to Stainless steel. My old ones I might add were less than 5 years old when we sold our house and all you had to do was spray with Windex and shine shine shine. Try that on the new ones streak streak streak, and nothing ticks me off more than looking in a kitchen and looks like pigs are running all over your stuff. Then the range aqua lift self clean. You have gotta be kidding. No self clean about it. Scrub Scrub Scrub by hand. You mean who in the hell came up with this. Make something with fat and instant burned mess. Really oil and water or grease and water where I come from they never mixed, and all they do is get gummy. Now if you dont care how your oven or outsides look then I guess it doesnt matter BUT I DO, I am with the guy that said he just wants to throw it out. I would have been better off buying a clean your own. At least you could use oven cleaner. I dont know where these companies are coming from ripping people off this bad, now that I am older I am stuck with it and can hardly clean it to get down in there. You make supper and you have to spend 2 hours extra in the kitchen scrubbing the damn thing. Of course you give a company loyalty and get screwed this bad. All my self cleaning ovens I had when we sold houses the people thought you never cooked in them. This is not even a year and a half old and looks like it is 10 years old. Even scrubbing it is a joke. You cant get it all anyway. Im sure I will not live with this long. I use to love to cook even did it for a living and man using this thing I hate cooking more than ever.

Whirlpool Cabrio HE washing machine - I was very excited when buying this product. It never really washed clothes thoroughly. I kept getting strange stains on them and even after emptying it as soon as it finally was able to finish a load without saying UL constantly... the clothes would stink. Im sick I ever bought it! Plus, it rusts terrible.

They attempted to fix our fridge, 1 year into owning, claimed no parts available. Never fixed, fridge died. Refused to repair. Offered us a 15% Visa gift card on another Whirlpool. Unacceptable, they can’t fix their product, and will never recommend anybody go through my familys $3,500 wasted fridge experience. Don’t trust them, they lie, and just escalate it to another liar in the customer service department.

The main control panel on my Whirlpool Cabrio Washing Machine broke twice in the second year of ownership. I bought this in 2006. The part was replaced in March 2007 and then again in October 2007. Now, it is broken again and Whirlpool says too bad, they will not replace it again and will cost us $275 to fix it. People have posted about this problem all over the internet. How can they not help their customers and recall this washer part?

Problem resolved - This is an update to my previous complaint... The repair man arrived this morning and after resetting the thermostat, the water heater started up again. He explained to me that these new water heaters are super sensitive because of the new designs and systems that are required by the State of California. He said that all brands have to have the same system. He said that the new water heaters dont breathe as well as the old ones. In our case, he suspected that after being installed, there were probably some air bubbles in the pipes which tricked the computer into telling it that there was not enough ventilation, when in fact our ventilation was fine, but that triggered a total shut down! In my previous written complaint, I was really upset because I have not had a shower in 3 days and thought this problem water heater would not be fixed until next week. I was furious! My understanding is that basically the way the new water heaters are designed is not very well and there is nothing we can do because about it they are all the same, unless we want to go to a tankless water heater system which plumbing included would cost $4000.00... so we are stuck and hope this will not happen again!

If you ever bought something from the store and the sales person said dont worry about, if you have any problems they will go ahead and fix it.... BEWARE... I purchased my fridge from BrandsMart USA in Feb of this year.... It was approx 2500.000 fridge we bought because it matched the rest of the appliances. Little did we know this has been a living nightmare. They have been out to the house 7 times to fix this thing. Its less than 8 months old.... and its still broken. I have been without a fridge going on 2 1/2 weeks. The Senior Customer product review supervisor said he would get me a new fridge that was on the 27th. Every time I call him, his voice mail is full of.... Only to assume that is full of other satisfied customers. I HOPE YOU WILL NEVER HAVE TO GO THROUGH THE PROBLEMS I HAVE HAD. What a waste of $2500.00.

We bought the Whirlpool Cabrio set from Sears in February 2010, for our second home. We counted up the weeks we have actually been here since then, it is about 10 weeks. We figure we used the washer about three times per week. So, we have gotten about 30 wash loads from this washer and it dies mid-cycle. We assume the motherboard crashed. It kicked the breaker. Lid was locked and we couldnt get it open. The washer would not power up. Repairman arrived three days later, got the latch opened but couldnt figure out what was wrong with it. He said it is probably a board and it might be better for us to replace. He wants to pick it up tomorrow to take to his shop. I called Whirlpool to complain. I know the one year warranty is up but to get 30 uses out of this expensive piece of junk and not get any consideration from the manufacturer is not right. I wish I had seen all these complaints before I bought it. No Whirlpool ever!

I purchased a Duet Front Loading Washer (model WFW9750) in May 2010. In September 2011, the noise level had become intolerable. I called a local service company. They advised me that the main bearing was bad. It would cost more to repair than what it was worth. I contacted Whirlpool. They could not do anything unless the machine was inspected by one of their authorized service companies, which they scheduled. Two weeks later, A&E Factory Service arrived and confirmed that the bearing is bad and the cost to repair will be $1,542.06. Whirlpool customer service transferred me all over the country to tell me that the machine was out of warranty and there was nothing they could do.

I purchased a Whirlpool oven and stove from hhgregg. The refrigerator is at best OK. The stovetop is easily scratched and looks horrendous after just a few months. Cooking controls are far too high for slow cooking. Customer service is terrible. Avoid, purchase another brand. You will be much more satisfied.

Plastic comes off drawer when you pull it out! Trim around glass cracked. Drawers cracked. My drawer literally has a hole in it! Warranty doesnt cover that! When checking reviews on amazon people all had same complaint and when they reorder product it does the same thing. This fridge was purchased less than a year ago! I purchase it from Discount Direct, a Costco outlet store!

I purchased a Whirlpool Cabrio washer model #wtw8200yw in August 2012. I just purchased a new washer today (Jan 2018) to replace it! We have had to replace the lid lock twice, then the cycle knob would only work on the normal cycle. Last week it started to sound like it was going to take off! Had a repairman come and the bearings went out in it, will cost almost $500 to fix! Not spending another dime on this junk! I purchased a new washer today (not a Whirlpool either!)

I live in Florida and in December 2012, purchased a Whirlpool upright freezer from my local Badcocks. About two months after the purchase it started making this weird loud sound. I contacted Whirlpool and they sent a local appliance company technician out to check it. The technician ripped my brand new Linoleum floor when pulling out the freezer. The result was, in his opinion, nothing was wrong with it, that the loud sound was normal. As it continued, another tech came out and his opinion was it needed a new compressor. So, it was replaced and lasted about a month. I was getting something out for dinner and noticed everything in my freezer was unthawed... all that money wasted a freezer full of food gone. So, Whirlpool once again sent the same appliance company out but a different technician. This one said it that he needed to order parts which he did, a different tech came out to install the parts and told us he didnt know what they were for and our freezer didnt need the parts the previous tech ordered. So this tech put dye in the lines and left. The dye leaked out from under my freezer all over the floor which is now stained because of the dye that leaked. This is the brand new floor they had already ripped during the first service call. So, now not only is my floor ripped but stained as well.Once again, about a month later, I find my freezer full of meat unthawed a third time. Once again I called and find out they have dropped the contract with the company that came out the first two times. So they refer me to another local appliance repair, and this new tech says that it needs a new compressor. This will be the second new one in less than 6 months. They order that part and repair the freezer; this fix lasted for about three months this time. On my fourth call to Whirlpool, I expressed my frustration with losing my food and the hassle of an inferior product purchased brand new under warranty. I definitely was not satisfied with the service and the customer service representative could not find my warranty record. He was also very rude and when he finally found my record, he told me I was no longer under Whirlpool warranty. This was wrong as I have my paperwork showing date of purchase AND the four-year extended warranty we purchased as well. I asked him what they would do for me since their inferior appliance and incompetent repair technicians cost me hundreds of dollars of ruined meat and other frozen food. He said they would do nothing except have another repair tech come out. Until the freezer is determined to be unrepairable that is all they can do.So I scheduled the tech to come out the fourth time and he found that some untrained tech had put oil in the line and the lines and compressor has to be replaced and flushed. I have already not had a freezer for a week waiting for tech to come out and now the parts are put on back order for another three weeks. The fourth repair tech called Whirlpool from my home, while I was standing there, and told them that it basically is beyond repair because of the price of parts and labor. He told Whirlpool it would be cheaper to replace the freezer but Whirlpool told the tech to replace the lines and compressor and flush everything out. So three weeks later, he comes back out on 10/13/2013 to make the repairs. I bought this freezer in December 2012 for $1200 and have been dealing with issues on and off since Feb. 2013 and now its 11/29/13 and once again my freezer has stopped working. I have lost all my food because Whirlpool sold me a defective appliance and would not make it right. I have asked them to replace it and they wouldnt. My husband and I have just purchased our second house and we were very excited about the remodel coming up in the kitchen. We were going to purchase stainless steel Whirlpool appliances, but after this company has treated me so badly, I will not buy anything with the Whirlpool name for our stove, dishwasher, microwave and refrigerator.We probably would have spent about $3500 on appliances, but we will purchase a different brand and give our $3500 to a company that will treat me better as a customer .I used to have trust in this company because it is well known for quality products, but I dont trust them anymore. I will advise any of my loved ones and friends not to purchase any Whirlpool appliance because of the inferior quality and lack of interest in making this situation right. I tried for almost a year and gave them 5 opportunities to do the right thing and now Im done. They dont care about the customer and that is a shame because they have lost a valued customer. As of now I have another tech coming Tuesday b/c my freezer is sitting not running again. Model #EV201NZTQ02.

Ive replaced my ceramic stove top twice. First time it was my fault, I dropped something on it. But last week I was the only one home, stove was off and I wasnt even in the room. I heard a bang, went and looked around. Saw nothing. But when I went to prepare dinner.... shock, the entire stove surface was shattered!!! Now at over $600.00 to replace it I AM NOT HAPPY!!!

My two-year old Whirlpool Duet Front Load washing machine is ripping my familys clothes. When I went online and saw all the other customers with the same issue, I contacted Whirlpool. Although the contact said that he knew I was frustrated, he could do nothing but send a repairman at a cost of $129 for me and then I would also have to pay for parts. I informed him that the online sites are saying that this is just a temporary fix. He pleaded ignorance and could offer me no other alternative. This is the last Whirlpool or Maytag product we will ever buy... and letting others know about the lack of cooperation.

I would like someone to explain to me why the control panel I.e. brains of the dishwasher which is around water is so sensitive to WATER. My daughter is the owner of the house and purchased this dishwasher last summer (2016) and within weeks we were having issue with the sensors. This supposedly was not covered under warranty (it was a WATER ISSUE). So now a dishwasher which cost over 700.00 is a door stop!! Where is people’s common sense... yes Im over 60 years old and very frustrated with the money that was spent for such an inferior product. Imagine having a dishwasher sensitive to water. The people who made it should give their heads a shake. Frustrated grandmother.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

Cabrio WTW8200YWO - We purchased this washer five years ago. About a year ago it started getting noisier and noisier on spin cycle. Now it sounds like a jumbo jet taking off. A Google search quickly revealed this is a ubiquitous problem with these washers. As we are in our 70s and dont have kids at home, we are very light users of the washer. First, I would suggest that no one buy this washer. Second, I suggest that Whirlpool should recall these washers. I called Whirlpool and it turns out they clearly know about this issue. The good news is they will offer you a discount on repairs or even on a new machine. The bad news is it will still cost you several hundred dollars to fix their design defect. I suggest that you avoid purchasing Whirlpool products both because of their defective design and because of Whirlpools unwillingness to take responsibility for these problems.

I used the Whirlpool website contact form, and described an issue I have with the Cabrio washing machine. When the form is submitted, it states that the company will respond in three business days. Two weeks later, after no response, I submitted a second contact form. It has been five days, and I still have not received a response.

Purchased this oven on 9/12 from Sears, did not purchase an extended warranty and didnt think it was necessary. Im a 64 year old widow and only use the oven on holidays, to date Ive used the over 5 times. With Easter coming, I decided to clean the oven. Followed the instructions, the door locked and the oven died. Im totally disappointed, now it would cost over 100.00 to repair, money I cannot afford. Called Sears and all I was told over and over again that they can send a repaid person and I would have to pay. I was also told that I should have purchased a Kenmore and I wouldnt have had a problem and finally I was told that they couldnt fix it and referred me to whirlpool customer service, who also told me it would cost over 100.00. A 19 month oven should not have died. It should have cleaned the oven and continue to work for many more years. Again, Im upset, angry and disappointed with sears & whirlpool. And dont know what to do. Does anyone else have this problem with the oven, is there a recall?

I purchased a Whirlpool duet set on sale at Lowes about two years ago. The front loading washer has been leaking when I put in a full load of clothes. It usually floods the floor when it leaks. I am upset and very angry because this leak has ruined the doors to my washer doors. Apparently, the defects with this machine was known by Lowes and the Whirlpool company at the time that I purchased it (thus the sale price). This was not forementioned at the time of purchase. What a lousy way to do business. Whirlpool screwed me. Shame on me. Never again.

One year to the day after the warranty expired, the meat drawer in the refrigerator began filling with water. Two repairmen have been to my home and cannot repair it due to a design flaw. Also, I had to pay for a cracked bottom tray that happened during delivery which I didnt know occurred at the time. Whirlpool is now ignoring my phone calls and emails. We paid in excess of $800 last year. What am I going to do now? Buy another refrigerator and get rid of this one? I dont make that kind of money and I feel Whirlpool should stand behind their products. This model is not even on the recall list so that means to me that other consumers buying this model are getting ripped off also. The customer service people say sorry but wont budge on reimbursement. I was told they cannot honor my request. Whether this was under warranty or not, it still cannot be fixed according to the repair tech that was at my home. I need to find someone to help me before this lemon I bought decides to burst into flames. I want a replacement refrigerator, not this model of course, of equal value. I am not asking for the moon, just for something that works beyond one year. In this economy, we cant afford to buy a major appliance after one year. My car is still running and I bought that in 1985. Please find someone to help me. I thank you for your time.

I purchased Whirlpool gas range with AquaLift Self Cleaning Tech exactly a year ago. DOES NOT WORK!!! The only Self that cleans will be you on your hands and knees. Still dont know what to use. Manual says do not use oven cleaner or abrasive or you void the warranty. Ok Whirlpool any suggestions? Soap and mild detergent not cutting it. You would think with all the customers complaining about this feature the bright engineers that designed this would come up with a solution.

The washer began to start making noises as if coins were in it or plastic breaking every time I wash. Also, it does not wring clothes out good and clean well. I have Whirlpool Cabrio.

I have had to replace my Whirlpool 50-gallon hot water heater 2 times. First time it broke, it caused thousands of dollars’ worth of damages plus Im out a $760.00 deductible. I had the last one just over 1 month and couldnt exchange it at Lowe’s because it’s a few days over a month. So I had to get return authorization before I could return it again. I went through speaking to a hateful CSR. After calling back again, the lady, a real nice lady, helped me. I will never buy another Whirlpool product again, and if anyone is smart, they will stay away from them too. Hateful, hateful CSR. Beware.

April 1, 2018 we purchased a new Whirlpool 36in. W25 cu. ft. French Door Refrigerator, model # WRF555SDHV, Serial #**. On 2/15/2019 the ice maker quit working. Kirbys Appliance in Prineville, OR ordered a new ice maker and installed it (it was still on warranty). On 5/8/2020 the ice maker quit working again...I called Whirlpool Customer eXperience Center, 1-800-253-1301. Had I purchased an extended warranty, it would have expired 3/31/2020. No one will come and fix or replace the ice maker at my expense, because of COVID-19. So, we purchased our $1,999.02 Whirlpool that does not make ice!! I will never buy another Whirlpool Appliance again.

There is a chronic and well-known problem with recent French door, bottom freezer refrigerators sold by Whirlpool, including the the brand names KitchenAid, Jenn-Air, Maytag, and Amana. The problem is caused when the defrost drain freezes, preventing defrosted water from reaching the evaporation pan. After enough water builds up, it overflows along the front of the refrigerator. In my particular case, we have wood floors and they were ruined by the water. After doing some investigation on the internet, I have learned that this problem affected approximately 1,500 model numbers sold under these names. These model numbers are listed in a Technical Service Pointer issued by Whirlpool.In August 2013, after experiencing several years of problems with these units, Whirlpool issued a Technical Service Pointer W10632338, advising service technicians that a new P Trap drain tube kit was now available, and suggesting that the defective duck bill check valve should be replaced by this new part. The problem for years had been that the rubber duck bill check valve would, over time, become sticky (or tacky) and would then not open - causing water to build up above it. Eventually, the water would freeze and since newly defrosted water could no longer escape, it would build up and eventually overflow.From what Ive seen online, plus a conversation with the Sears technician who come out to diagnose and repair my leak, I am convinced there are many thousands of customers who have experienced this problem. Because it takes a while for the rubber check valve to become sticky and no longer open, it is not uncommon for the problem to not appear until after the standard one-year warranty has expired. From reports, Whirlpool has sometimes acknowledged the problem and effected repair of refrigerators no longer under warranty.But what about those customers, like me, who have experienced water damage to floors and cabinets? Shouldnt Whirlpool be liable for those repairs, too? Id be interested to know if anyone knows of plans for a class action lawsuit.

I purchased a Whirlpool Cabrio washer and dryer. They work well but the washer underneath lid has rusted already. I did purchase the washer in Dec. 2011 and in June 2012 the inside lid to my surprise had rust on it. I called the Whirlpool company and was told that is considered cosmetic and not covered under warranty..

Whirlpool WFE720H0AS0 - I tried to use the self cleaning oven feature and it cleaned the bottom of the stove but did nothing for the sides, back and door of stove. The top of the stove is impossible to keep clean. Maintaining this appliance is a full-time job. Very bad choice.

Had washer since 2016. Have NEVER washed a load where there was not a problem from washer dancing to having clothes come out without water ever touching them. Would NEVER recommend Whirlpool! Tried to contact Whirlpool website to register a rating & even their website is defective - could not get through after several attempts.

I bought a Whirlpool built washing machine on Jan. 8, 14. It stopped working on Aug. 9, 14. It is now Sept. 2, 14 and I am still waiting for it to be repaired. I am age 75 and it is difficult to load and unload clothes to take them to the laundry. The repairman order a part Aug. 26. Pony Express has not deliver the part at this time.

We have owned refrigerators for over 40 years. Never had one as bad as this. Three ice maker replacements lasting maybe from 6 months to 2 years. Cap that off with customer service people who by voice and tone could not give a rats ** about helping the customer. Today it took me from 3:10 pm to 5:30 pm to get a real person on the phone. When I did the attitude is so reminiscent of a fast food hamburger joint with arches. Yes they know the refrig and ice maker are and have been a problem but they don’t care cause we have no option. Whirlpool will NEVER SEE ANOTHER penny of my money. Time to look at real appliance makers. Horrible.

I purchased a Whirlpool side-by-side refrigerator from Lowes for $1,100. It arrived missing a shelf. Last year, the warranty expired and the ice maker mysteriously failed. Next a drawer slide failed. Next the lights, both of them, failed. I was offered a service call, the estimate $300+. Next, the ice bucket bottom broke and filled the freezer with cubes. Next another drawer slide failed. Whirlpool makes an over-priced, poorly engineered, poorly made product and Lowes sells their products without any care for their customers. I will do my best to warn anybody who is interested that while Whirlpool used to be a good company, it has degraded into producing junk and trading on a once storied reputation. And Lowes touts these products without any interest in its consumers.

We have recently retired and moved into a smaller home. The kitchen needed to be furnished with all of the normal appliances. We bought two Whirlpool products, a refrigerator and trash compactor. Since we are living on a fixed budget, I was hoping that the furnishings that were bought would last as long as our past appliances did. However, our brand new refrigerator after two and a half years needed to have a new light installed. We called Whirlpool and set up for a repair. The repair was $290.00. We paid the repair man working for Whirlpool, then called Whirlpool and asked if there was anything they could do to help with the cost. They suggested that we buy a protection plan. Both of the refrigerators we have owned during the past fifty years lasted twenty plus years. This one only went two and a half before having to be serviced.Whirlpools answer to my request of helping out with this $290 service call was Sorry, you should have bought a service plan. I wish I would have gone with either of the same brands that we had in the past. Those being, Sears and Sub-Zero. I would suggest that those of you who are contemplating buying a kitchen appliance, choose a company that has a product that will go more than two and a half years without having to be serviced. Neither of the other refrigerators that we had ever had to be serviced. They stayed with the houses we sold.

On Dec 18, 2015, my hot water heater located in my garage started spewing water out into my garage, driveway, and into the street. I called Lowes, whom I purchased the water heater in Jan 2011, in which it was still under warranty. I was told to call (Whirlpool) 877 817 6750, the order was placed for a gas shut out valve after going through a check system. I was then given the names of two local preferred technicians to repair water heater, whom was not available. The representative from Whirlpool (American water heater) told me I can get the plumber of my choice, authorization number was given. I had to call the (Whirlpool) (American Water Heater) back and was told the part was ordered 2 times. The first part will come on Dec 19, 2015 by UPS, and that the second part will come on Dec 21 by UPS, that a prepackaged label for return will be attached, and to tape the 2 boxes together to send back to the company--one box with the old part, and one box with the new. So, I sent the boxes to an address in Junction City, Tn. But I was not sent prepaid label, so I kept by word and spent $14. I will not be reimbursed according to American Water in which I followed their directions to a tee. So the walk away, the customer is always wrong, staff is not being trained the right way, and as a customer I am out of money and making adjustments to the way of customer service. No service. Just a waste of time, effort, and money.

We purchased a new Whirlpool dishwasher in June of 2014. By February 2015 the racks were rusting. I called loses warranty and they referred me to Whirlpool since it was still under a year old and covered by the manufacturer warranty. They said no problem and would have new ones sent out. Three months later I still did not get them. I called them back and they said that they were not covering them due to rust being normal. This is the absolute worst customer service and it says a lot about how Whirlpool stands behind their products.

Less than 1 year ago, I bought a washer and dryer. From the beginning, we have had a water problem and the water only comes cold... no warm water in the normal cycle. They came 6 times to service the machine and they cannot fix it. They said there is nothing is wrong with the machine but it does not wash with warm water in the normal wash cycle. I advise not to buy this product anymore. It is under a warranty so they should fix it or replace it. I am sick and tired of talking to them. They said if we send the service guy then I have to pay for it which is not acceptable because it is under a warranty. If anyone is thinking about buying this product, I advise not to get it and waste money on it.

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

I purchased a Whirlpool washing machine (new) in 2004. From the beginning, I had problems with the spin cycle. I phoned Whirlpool. I paid for service with no reimbursement. With the costs I have had for service, I could have purchased 2 machines. I have had to go to Laundromat to do wash then come home to dry. I have for 30 years only purchased Whirlpool large appliance. My washer and dryer were always refurbished but they were Whirlpool. I have had a (refurbished) Whirlpool dryer since 1997 with one (1) service call. However, this wash machine, purchased new, has been a money pit and a piece of trash with Whirlpool only giving lip service when calling. Also, going to the Laundromat, I have been amazed at how many individuals I speak with are there doing wash because their Whirlpool washer, mostly even newer models than mine, do not work! And they have the same story. There’s no service when you call. Shameful Whirlpool! Buy your parts from us. Maybe your credibility could be restored. But I will never purchase your Whirlpool or other names under Whirlpool! When I do get another washer, yours will be put on my front lawn with a large sign of your disgraceful products and service!

Only problem is you have to open door to access functions. 30 second increments and stop are on outside. Beautiful to look at and inside is easy to clean. 4 fan levels, vent inside or outside. 2 light settings. Nice and bright. Low profile over stove but big enough to hold large casseroles.

My Cabrio washer worked fine for approx 3 years. Within the last 9 mos there has been one repair/replacement issue after the other: pump, computer board, bearings, seal, etc. Whirlpool takes no responsibility. Worse purchase I ever made.

My washer and dryer have been a great experience. Doing laundry has never been my favorite chore but these energy efficient and state of the art machines live up to their advertising. One of the best things I like about the washer is the ability to set the run time for a future time. I do wish the dryer had something similar.