Purchased 11-02-2016. This Whirlpool/Kenmore dishwasher is falling apart. Top rack wheels are totally broken, ordered parts 4 times, gave up. Now they are held together by gorilla glue. I have gone through 3 gray plastic end caps for the top rack runners. Now one is contained by a plastic slip tie. Last week it started leaking. Sears was totally useless. Whirlpool keeps sending me back to them. Now, I have to go buy another new dishwasher. It will not be a Whirlpool. Next time getting the extended warranty.

We purchased our oven from Sears, and less than two years later, the oven would not cook a chicken. We do not use the oven very often. We grill out and use the top burners often. We had the oven repaired through our home warranty program, and now 8 months later, it seems to be occurring again.

I purchased a Whirlpool Flame Lock gas water heater with a 12 year warranty from Lowes in November 2011. It lasted almost 6 years. Called Whirlpool Support and no one in my area is a certified repair facility. Closest one is 45 miles away, and he wont drive up to check out my water heater because Im too far away. Called someone in town. He came out, looked at it for 2 minutes, and said he never saw a water heater like this, but Sears may carry parts. Charged me $50 for service call. Sears couldnt find the model number in their parts catalogs. I dont have a manometer (What is it?) so I cant do diagnostic tests on it myself. Cant find out anything about them online except complaints from other steamed customers about this crappy product. Whirlpool Support wouldnt do anything else for me except say they were sorry I got stuck with a bad product of theirs. It was made for Whirlpool by US Craftmaster Water Heaters Co.

Im a member of Costco. I trusted that they will sell me a decent refrigerator, wrong! I bought a French Door refrigerator by Whirlpool on March 2018. It freezes my food on the left compartment and on the middle compartment. I called since its under the one year warranty. They came 8 times already and changed parts and promised me every time they came that this will resolved the problem... still the same. I have been in the phone with Whirlpool for one hour and a half for 5 times and they still want to do more tests. I will never buy another Whirlpool unit again! Costco should be ashamed of selling this brand! And they should paid for this also.

Purchased this Whirlpool Duet washer WFW920ww00 in 2011. 6 service calls while under 1 year warranty. The mother board was replaced..... after I smelled smoke and burning. Had trouble draining.... error codes F9E2 and F9E1 and SD (suds) and low flow were the usual. At times took 4-6 runs to get it through to point where I could open door. Often need to unplug for 20 minutes in order for it to progress. Clothes would not ring out... or be floating in water. Lately had to run on medium spin just to get it to work at all. The odor/smell was horrible and the rubber ring was black with mold after the 1st year. Completely stopped working this week, no power to panel. The repair shop said to not bother.... he has had customers replace 2 or 3 major parts in these and still keep getting the annoying error codes and difficulty making it through a complete wash. Moving on and buying something else.

The problem started with an error code F3F1 on dryer. Called A & E Factory Service who is company that are certified Whirlpool technicians. They have been out 7 times, March 26, April 1, April 8, April 13, April 27, May 5 and May 12. During those times they ordered and replaced the main control board 3 times and a thermistor for which we paid for parts and labor. The company now says they think we have a lemon and we are supposed to hear back within 48 hours whether we are going to be refunded a total of $504.48 we have advanced for repairs less the service call. They referred us back to Whirlpool and said they would no longer come out as the dryer cannot be repaired! Talked to Whirlpool customer service that says we didnt have an extended warranty and there is nothing they can or will do. This dryer was purchased on 12/31/11. They took the position that because there is no recall for defective parts for this model, there is nothing they will do. Attached is our purchase receipt and all service invoices regarding this matter.

The plastic frames for the glass shelves are cracking at the corners and the only option Whirlpool has given me is to replace the shelves at about $150 each. Needless to say, the cracks started just after the 1-year warranty expired. If only one shelf was cracking, it could be my fault; but since all are cracking (some on the front, some on the back and some in multiple places), I believe this is a design flaw and should be covered by the manufacturer. When I call, I can only get through to someone to schedule maintenance or order parts. What can I do?

Called 8/24/15 - spoke with representative about our two year old washer. Nothing Whirlpool can or will do.They have no other complaints about rust inside the lid and inside rim at bleach dispenser nor chipping of paint from lid. When asking the Whirlpool representative about the rust, he assured us there were no other complaints.This is hard to believe since our recent research clearly shows that other brands have had to replace tops due to rust. As for clothes not cleaning, no response to this issue. Whirlpool has not trained salespersons and therefore at the mercy of Lowes hard sales tactics and we were very delinquent in researching numerous complaints before purchasing Whirlpool Cabrio Platinum Model WTW8240YWD - Ranked lowest possible from ConsumerAffairs with hundreds of complaints. Whirlpool should be ashamed of product - clothes do not come clean, there is no soak cycle, no way to open mid cycle without losing all water, washer smells horribly, must be cleaned - are you kidding? Who cleans the washer that is supposed to clean clothes with a special cleaner?? We understand safety issues of water in open machine, wonder if Whirlpool understands the need to have a soak feature to clean clothes. Undereducated buyers like us and the totally undereducated salesperson at Lowes were obviously a horrible combination. It was all about sales for them. No one mentioned and we had no clue that the huge drum would not clean clothes even using less water than a traditional machine. We thought platinum meant a high quality machine. It clearly was a cleverly used buzz word for sales not a premier cleaning machine. Never, never, never purchasing Whirpool anything again. Wonder if Whirlpool cares, if they read the ConsumerAffairs reports, if they respond. Our hard-earned money is wasted. Our clothes are dirty, the washer smells, and the top is rusting out!

Hello, Here is our story. We bought this refrigerator Whirlpool - 26.2 Cu. Ft. 4-Door French Door Refrigerator through a local reputable retailer. After 16 months we started to have problems with ice melting in the ice bin. We continued to have problems related to cooling/freezing within the refrigerator to the point where almost all the major parts were replaced. The good news is the dealer negotiated with Whirlpool to have all repair costs covered after the first visit. I asked about just getting us a new refrigerator and was told Whirlpool requires a part to be replaced 3 (THREE) TIMES before consideration.In summary, the refrigerator could not be fixed and was condemned in agreement with both Whirlpool and the Dealer. Here is the interesting news - since the refrigerator was out of warranty (12 months and now we are at 18 months), they are requiring we pay $600+ for the replacement. Buyer beware - either pay for the extended warranty or risk having to be inconvenienced by having your refrigerator unavailable for days or in our case, weeks!

Top loading HE machine. Washer does not clean. I have tried all manufacture recommendations, changed detergents and tried laundry boosters, all to no avail. Tshirts, pants and socks routinely come out of the wash dirty and must be re-washed. This negates any energy savings. Also, the noise from the spin cycle is very loud - the washer is on the second floor but I was told by sales person that this would not be an issue with top loader. Overall, very disappointed and after all these years, I have finally given up on this washer and will junk it.

I have bought two Whirlpool water heaters and with each one have had the same problem: the pilot light will not stay on. I have to continually turn the pilot light on each day. I have replaced the entire flame/pilot/thermal couple assembly several times. Each time I use the unit, it works for about 2 weeks, then Im back to turning on the pilot light every day. Im convinced that there is an inherent design flaw that Whirlpool should be forced to deal with. It seems that this should be a fraud case to sell a known, documented, defective product. Shame on you Whirlpool! Its obvious that its all about the money! Band all Whirlpool water heater products!

The unit is electric and Im not impressed with the oven temperature consistency. The oven either runs hot or cold so trying to bake anything to perfection is a challenge. Ive added a stand alone thermometer just to ensure cooking properly.

My Whirlpool dryer - Model# wgd49stbw, serial# ms2405113 went out on 1-29-16. Which I purchased from Lowes in August of 2015. Called the service company that I have my extended warranty with. They came out on 2-1-16. They did not have the part I needed in stock. It had to be ordered by the manufacturer. Sadly, I am still waiting and have been told it might come in on 3-29-16. Every time I call it gets pushed out another two weeks. This is really ridiculous. All the money I have spend at the laundromat I could have had a different source come out to fix. Which I still may do. I will never purchase another Whirlpool appliance again and certainly will NOT recommend. I am 65 years old and have a hard time dealing with the laundromat. If they get this part in by 3-29-16 it will have taken them two months. So sad.

My wife and I purchased our Whirlpool Duet Model # WFW95HEDC 7/19/16. I put my first claim in on 12/19/16. We were sitting downstairs one night watching tv and all of a sudden a noise like the sound of a tractor trailer putting on its jake brake came roaring from upstairs. It was so loud that we both jumped. The machine would periodically vibrate violently while going thru its spin cycle. The frequency started to get closer and closer together. Whirlpool had a technician come to our home. They came out 3 times and said that nothing was wrong. They said that it was vibrating because it was on a pedestal and upstairs on a non solid floor. They also blamed the loose water hose on the noise. SERIOUSLY??? After the 3rd visit, and a week before the 4th visit our machine started to leak. We paid $1,079.00 for this washer and we were having to take our laundry to a laundromat to wash it. The technician came out the 4th time and replaced a cracked drum. Apparently it vibrated so badly that the drum cracked. So everything seemed ok, then WHALAH!!! We wash the clothes and go to move it to the dryer and it is dripping wet. Somehow after they replaced the drum the machine started to not spin the water from the clothes very well. Takes drying the clothes for 50min 2x to get them dry. I am now set to have the appliance company come out for a 5th time and still not corrected. Whats worse is that every time I contact Whirlpool they give me the same canned speech and want to set up another appointment with the appliance company. I am soon at the year mark with my manufacturers warranty and still having issues. I think Whirlpool keeps kicking the can down the road without making good on correcting the issue so they can get past the year mark and make us take it up with Home Depot on our extended service plan. I feel bad for everyone out there who got screwed by this company.

On March 3, I purchased a dishwasher (Model: KUDE70FXSS1 Serial No.: F10202361) on Whirlpools VIP link, which will more likely be my last Whirlpool purchase based on the slightly damaged product and incredibly poor customer service Ive received. Upon delivery of the dishwasher on March 9, I noticed that the left rear wheel was damaged and slightly bent. I also noticed that the unit was a little off balance. But the delivery person explained to me that everything was okay and that the front legs just needed to be adjusted. I believed him and signed the delivery receipts with the additional note about the left rear wheel being damaged. At the time of delivery, the driver also happened to mention that J.B. Hunt did offer installation services for dishwashers. I then called Whirlpool customer service, which pretty much gave me the cold shoulder, and said that it wasnt in their policy. I had to request the installation service at the time of purchase and Whirlpool would not send someone back out. This made me upset because I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. Im not sure how Im supposed to request the installation services when theyre not being offered. But the genius customer service representative thought that I should intuitively call Whirlpool when the link isnt on the website. This is the first demonstration of Whirlpools poor customer service, in my opinion. After a couple of days of driving around to get a hose and a cord to perform the installation, I finally installed the dishwasher on March 12. Once installed, I noticed that the hinge on the left side was rubbing against the tub of the dishwasher. The door hinge was bent and the main tub was slightly damaged. Again, I contacted Whirlpools customer service department who sent out a repairman who confirmed that the dishwasher needed new tub and hinges which were covered under warranty. Unfortunately, he told me that I would not receive a new dishwasher since I installed it myself. He would order a new tub and hinges and transfer all the equipment and wiring from my original dishwasher to the new tub. Essentially, I would have a refurbished dishwasher at a new price, which I do not want.I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. If Whirlpools website worked the way it should have and offered an installation service, I wouldnt be in this situation. I would have paid for the installation and the people installing the new dishwasher would have realized that it was damaged prior to them leaving and ordering a new dishwasher. I am a customer and not a dishwasher repairman. No normal person would have been able to catch the damage that is on my machine. Second, I find it hard to believe that Whirlpools policy states to have all the equipment from my original dishwasher installed on a new tub. So, I paid $989 for a new dishwasher thats really a refurbished dishwasher because of the damage. I wish I would have visited this site prior to purchasing. I will never deal with Whirlpool again.

Really pretty fridge... wish it was just a little smaller. Also wish matching appliances had grey sides like the fridge does. So far it has been a winner.

We purchased Whirlpool Gold Accubake, double ovens (gas) in 2005. Since then, we have experienced identical failures (8 to date) during the self-cleaning cycle in which the high temperature burns out the thermal fuse of the ovens. This requires two Sears technicians to repair the unit (it requires two technicians to pull the oven out as the fuse location is in the back of the unit) and leaves us without use of both ovens for approximately 2 weeks (scheduling parts delivery and technicians through Sears home repair is not an expedient process).After checking other consumer product websites, it has become clear to me that there is a known design defect with these ovens in which the thermal fuse is not adequately insulated from the high temperatures during self clean; it therefore trips and burns out during the self-clean cycle. While not having access to ovens for about two weeks/year on average may sound acceptable to Sears, the reality is that the problem has escalated in frequency since purchase. In 2013, we are going on our third repair of the same problem (that makes 6 weeks of non-usable oven time in one year) and Sears will not consider replacing the unit, despite: 1) our obvious dissatisfaction with a lemon unit, 2) a well documented history of the defect with this particular Whirlpool oven and 3) an ongoing and escalating repair cost to Sears (it is under their extended warranty so the repair cost is on them although we did pay for this service up front on our appliances).I would stay away from not only Whirlpool appliances but also Sears as there doesnt seem to be any regard for the customer experience and taking care of a product problem (the right way) with a known defect. Sears has an opportunity to make this problem go away quite easily and retain a customer - fix the problem permanently or just replace the defective unit. Unfortunately, my experience to date with Sears standing behind the products they sell provides me with little confidence that either will happen.

Soon as warranty expired issues with product. This should not happen. Made in America, washer making too much noise. Products cost more but poor quality. What is this company going to produce? This is the world we live in.

I love my ceramic top. My only complaint is I wish my knobs were on the front of the stove because I am short. It would be nice to not have to reach over hot burners just to turn the temp up or down.

Oh my goodness, are these people right with the Whirlpool Ranges. I moved and put in the appliance # to get what I had from Whirlpool. What a piece of crap I got in a range and refrigerator. Never had appliances that looked so pathetic. You cant clean the outsides or the insides. Outsides nothing but streaks never look shiny, I really do doubt they are even close to Stainless steel. My old ones I might add were less than 5 years old when we sold our house and all you had to do was spray with Windex and shine shine shine. Try that on the new ones streak streak streak, and nothing ticks me off more than looking in a kitchen and looks like pigs are running all over your stuff. Then the range aqua lift self clean. You have gotta be kidding. No self clean about it. Scrub Scrub Scrub by hand. You mean who in the hell came up with this. Make something with fat and instant burned mess. Really oil and water or grease and water where I come from they never mixed, and all they do is get gummy. Now if you dont care how your oven or outsides look then I guess it doesnt matter BUT I DO, I am with the guy that said he just wants to throw it out. I would have been better off buying a clean your own. At least you could use oven cleaner. I dont know where these companies are coming from ripping people off this bad, now that I am older I am stuck with it and can hardly clean it to get down in there. You make supper and you have to spend 2 hours extra in the kitchen scrubbing the damn thing. Of course you give a company loyalty and get screwed this bad. All my self cleaning ovens I had when we sold houses the people thought you never cooked in them. This is not even a year and a half old and looks like it is 10 years old. Even scrubbing it is a joke. You cant get it all anyway. Im sure I will not live with this long. I use to love to cook even did it for a living and man using this thing I hate cooking more than ever.

Purchased a Whirlpool French Door Refrig. Model #WRF 954CIHZ200 in 11/21/2017 from Best Buy for $2300.00 on sale. Within the 1st year the Ice Maker broke & repairman said the ill design caused the wire to break. He had replaced numerous ones for the same reason. In the 2nd yr the freezer started frosting. Next thing the freezer quit. Next day refrig quit working. Called Whirlpool, said, So sorry. We will send you a $50.00 Visa gift card. That was to cover $200.00 of just bought groceries. Called repair guy & he diagnoses compressor was bad. (IN A LESS THAN 2 YR OLD REFRIG. THAT COST $2300.00????)Now, we are 28 day w/o refrig. Living with a Igloo cooler. Whirlpool says they have no stock left on compressors for our refrig. (probably because there are so many going bad in their refrigerators). They are trying to locate one somewhere in US so that takes 6 days then they have to ship to repair center then they have to schedule us for repair which will probably be another 7 days. Ghee, what a mess! Dont do it folks! Buy a LG or Samsung! If I had it to do again, thats what I would do! Whirlpool is Not what they use to be when I trusted them. Years ago. P.S. I bought microwave, stove, & dishwasher! They are all unsatisfactory! Never again!???

The refrigerator is a Whirlpool Model #GSC25C6EYW0. We purchased it on September 17, 2013. So far we had to fix the ice maker, the drawer broke, the refrigerator cools unevenly. They tried to fix it but cant. Therefore, I cannot put tall things on the top shelf. Now it is not cooling and I have to repair or replace it.

Called Whirlpool customer care for help with identifying make and model number of a slide-in, ceramic cook-top range (one of their popular brands). The representative was cordial, patient and very helpful when it came to giving me directions on how to locate make/model information on the unit. That was until I let her know about a recent problem with the stove. The edge of the cooktop is much too sharp! My hand got cut while wiping down the stove top/adjacent counter. Although Ive had the stove for a while, Id never had that happen before; thats probably because I used a thin rag this time around to do the cleaning. I asked the rep if anyone else had reported getting cut by the stove top. She said, No. I let her know that my goal was to just them know about the situation, because such a sharp edge on a cooktop is a safety issue. She disagreed. But what could or should she have said? In all fairness, it came down to balancing loyalty to the company with genuine care for the customer.I do appreciate how kind she was in communicating with me, but am very displeased that once Id shared about the problem she seemed rather dismissive of the situation. How could the risk of being cut NOT be a product safety issue??? If you visit the Consumer Products Safety Commission website, you can see where risk of laceration is a reason some products are recalled. Based on that understanding, I would say that sharp edges on a ceramic cooktop IS a safety issue!

We bought the Whirlpool Gold series side-by-side about 2 years ago with an ice maker in the door and with this design, the ice bucket is on the inside of the door, which we thought was a very clever design, taking up less freezer space. Well, to remove the ice bucket, we had to use a blow dryer because even though you press the button which is supposed to disengage the bucket from the door, it has always been frozen onto the base.Then we started having issues of water leaking from the ice maker. It turns out, that the lever that controls the chute was broken. We called a certified Whirlpool technician to come out to fix the ice maker dispenser lever. Well as it turns out, it cannot be fixed. It is a sealed in the door unit and to fix it, we have to replace the door, a repair estimate for door and labor is approximately $800. That is absurd.I contacted Whirlpool and was told that my refrigerator is out of warranty and that there is not an option to repair the dispenser. There is nothing we can do. I said that according to the repairman, we are not the first to report this problem. When I contacted Whirlpool I was told there is no recall for this item. We purchased the Whirlpool based on the reputation that it has had in the past and the good product we have in a Maytag (which is associated with Whirlpool) dishwasher. Well, never again are we going to purchase a Whirlpool or any of its subsidiaries products. I have read so many unhappy customers here that I cannot believe that Whirlpool continues to make such inferior products or designs.

I purchased a Whirlpool microwave model #WHM3205XVS1 on October 2, 2011. The handle broke off in little pieces and was repaired in March 2012. Handle broke off again in little pieces in September 2012. This will be the 3rd handle that will continue to break in little pieces every 6 months. According to both repair men that were here, this is their comment: No customer abuse, this is a very common problem with this model. After to speaking to 3 people at Whirlpool, I was told by everyone, This is cosmetic problem and we will not fix after the 1 year manufacturers warranty is up. I started with the the first person, went to her supervisor, then went to her supervisor. I am now waiting for a call from a manager although I was told I will continue to get the same answer no matter how far up the chain of command I go. So, I was told that it is okay to have 2 screws sticking out holding the remaining part of the handle that is left, because it is a cosmetic, not a functional problem. I will never stop with Whirlpool. I will call 4 times a day if necessary. I will never purchase another Whirlpool product again! I will tell everyone I know not to purchase one of their products. Be careful. They manufacture products for many other companies, i.e., Sears, Amana, Jenn-Air, and many, many more.

I purchased my Whirlpool refrigerator in March of 2011 and the ice dispenser failed in early April of 2012. I called Whirlpool and asked for a repair, but they refused, saying the refrigerator was out of warranty. Being a handy person and upset about the failure after only just over a year, I took the dispenser apart and found that a plastic part had broken and caused the ice door to become unhinged. I called Whirlpool back and explained what had happened, but they refused to help again. They transferred me to the parts department where I was told that the part that was broken was not available and the only thing I could do was replace the entire door! Not only is their product poorly designed, but it is also not easily repaired. I will never buy another Whirlpool appliance.

We purchased a Whirlpool Cabrio washing machine on 3-18-16. In February of 2017 the washer died. I was bleaching my whites at the time so most of the clothes, whites fell apart because they sat in bleach and water for 2 days. I had to figure out how to get them out without getting bleach and water all over my clothes. I called whirlpool and they got someone to come fix it. The tech came and said we needed a new control panel. We waited 3 weeks for the panel. He came on 3-24-17. He put the part in. Took less than 10 min and said, All set. I went downstairs and put a few things in. I was a bit leery and the machine started. I went back upstairs and I hear beeping. I go back down and the machine is flashing again. I called the repair people they said, Unplug it for 10 min. It may reset itself. If it doesnt, call back. It didnt. I called back and wanted me to wait till the following week. I told her I had clothes in there.Someone came the next morning and said it needed a harness and they would order it. Well its the 28th and I havent heard anything. I have called whirlpool several times with no satisfaction. We had the machine less than a year and its been dead for 2 months. I am disabled. I have multiple sclerosis so every day is a new issue. I hate to put that in here but I want you to know what Im dealing with along with a dead washer. Any help you can offer would be appreciated.

I have had my Whirlpool Washer for many years. It agitates well and my clothes are always clean. They are easy to dry. The wringer wrings out all the water, yet they stay damp for ironing. You will love this machine. I am happy with it and hope it lives for a very long time.

Aqualift Self Cleaning - JUNK! JUNK! JUNK! The oven does NOT heat properly and it is NOT self-cleaning. Whirlpool should be ashamed of itself. We ALL need a refund. Class Action suit looming. DO NOT BUY THIS PRODUCT!

We bought a Whirlpool Refrigerator - Model ES5FHAXS in 2006. Right off the bat, a line in the back of the refrigerator was leaking. We paid for the repair. Next after just one year, the refrigerator would be warm and the freezer part ran super cold. The settings did not work. After much haggling with Whirlpool, they paid for someone to come out and repair it. It worked for several weeks then the same problem came back again. We argued with Whirlpool again and someone from AES or AAA came out. The problem was fixed but once again came back again after a couple months. We called Whirlpool again. This time was much haggling and arguing but got them to come out a third time. Once again, the problem was fixed but came back again after several months. The repair company stated that if they found it was something other than what they fixed, we would be charged. I said either it was not fixed right or the refrigerator is a total lemon. I said you will probably just say it is something else to cover your costs. Whirlpool acted like they did enough, even though 3 repairs could not get it right. If we paid or each repair ourselves, it would have been nearly the cost of the refrigerator and it still would not have worked. We bought a refrigerator back in 1992 and never had any problems after 16 years when we moved. The refrigerator was not cheap but could not do what refrigerators are supposed to do - keep things cold all the time. What a disappointment.

I had sold appliance for ten years. I purchase a Whirlpool Cabrio 2010. After two years started rusting. It is rusting on the outside and now on the inside, that I cannot wash delicates or whites. I so disappointed. I had lots of confidence in Whirlpool. The model is wtw7300xwo... I call talk to whirlpool but got no help. Now I going to need to purchase a new washer. It will not be a Whirlpool.

Gas control not working. I have replaced the thermostat twice in three years. Now, the hot water tank pilot will not light. The igniter works; a new thermostat has been properly installed, and the pilot will not light. The gas is on, and the tank has functioned. I just want a new gas control.

I have had a plumbing company work on my Whirlpool water heater three times in the last two months. On the third visit, he told me all the problems customers have had with Whirlpool water heaters. I decided to call Whirlpool for warranty purposes. The unit is three years old. I was told that it was the gas valve, and I was given a free one from Lowes. After installing the new valve, it still did not work properly. After troubleshooting with a technician, I was told it was the orifice. I have had to do all the labor myself, and I dont know how long this is going to go on. I have heard Whirlpool will continue to give you the runaround (from the plumbing company and Lowes salesmen) and will continue to give you the runaround and not replace the unit. They are wearing me down. I have been without hot water for three weeks with no end in sight. I am ready to give up and just buy another water heater but certainly not a Whirlpool.

Similar to what I am reading below and on other sites, my hot water heater stopped working. I spent about an hour trying to relight the pilot light, which apparently you cant do with this model because it breaks. My first thought and action was to call a plumber to come fix it. When he arrived he said it was reverse thread and that I would have to call Lowes to get a replacement part. When I called Lowes they said they would call Whirlpool and then give me a call back. Two days later I still havent heard back or taken a shower; I am going to the gym tonight. Finally, I got online and called the 800-number and am being sent a part to arrive tomorrow. I asked to be reimbursed for the cost of the plumber since they obviously knew they had a problem (they assumed why I was calling the warranty line) and redesigned the issue with a voluntary recall. Whirlpool, please make this right. I know you license your name to American but it is still your name and brand reputation.

I bake a lot so my husband bought me a new gas range for our 54th anniversary. After the first few times I used the oven, I decided to clean it. I noticed then that there were some burnt grease spots and streaks between the oven glass door. After 2 years of use, it has gotten much worse so I decided to take the door apart to try to clean the glass in between the layers of glass but there are three instead of two. I cleaned the inside of the outer glass, but that didnt take care of the problem. Most of the stains are between the other two panes of glass. That, I cant get to. I feel that this is poor design and not sealed properly. I take good care of everything I own and I expected this range to last me the rest of my life but it is put together with cheap plastic parts that wont last long. It is the first new range that I ever owned and paid a lot more for it than any Ive had. I expected better.

My wife and I spent about $2500 on a new Whirlpool Dutch Door fridge five years ago. 18 months later the evaporator went out and the warranty was only good for one year! We bought an extended warranty, got it fixed and the other evaporator went out less than a year later after that! Next, the circuit board control on the crisper went out. Then, the water filter would not disengage and a repairman had to take the fridge apart just to put in a new filter! And now, the ice-maker has gone out and the fan is icing up like another evaporator is going... Insane! Our warranty is up next year. Once the warranty ends we will start shopping for another unit - and it wont be a Whirlpool - thats for sure. I have never owned anything this unreliable in my entire life! Also, I would say most of the time we have owned this piece of you-know-what it has made a loud disturbing fan noise... What a waste of good money! Run! Run far, far away!!!

Phone calls took too long (30-45 mins each). Connection was bad. WHIRLPOOL APPLIANCES ARE **. Whirlpool appliance was poor quality, broke down and not fixable. Unable to find replacement dryer ANYWHERE that will match my existing washer stacking kit. The loyalty program discount is a joke.

Purchased Whirlpool Gold appliances for a kitchen reno two years ago. Fridge and stove from a dealer and microwave from Lowes. Fridge - After one year the ice maker quit. $200 part plus labour. Seal on fridge door not sealing. New hinge and washers to adjust. $30 plus labour. Stove - three different stoves were delivered with the same paint flaw on the top of the control panel (3 inch section where paint did not adhere or was scraped off... Same spot on all three... clearly a factory issue). Stove door - when you touch it the interior light goes on. Warming button and switch was broken when purchased but didnt notice. Whirlpool wont warranty. $48 plus labour. Last piece in this puzzle... Microwave - magnetron went and wont heat. $300 plus labour. Obviously time to change brands. Now to figure out who is NOT under the same manufacturing umbrella.

Seems to use very little water. When I take the clothes out, they are bone dry in places which means they havent even seen any water! Clean (?) clothes end up smelling musty and I end up having to wash them two or three times which completely goes against any eco argument! I am really disappointed with this product and would never buy Whirlpool again. I have just washed our dog blankets. The cycle finished so took them out, had to check that the detergent had been used as the blankets were almost completely dry. The blankets still completely smell of dog so have had to put them through another wash (with more detergent – waste of money) and with a pre-wash cycle. Rubbish! We also have a Whirlpool drier and that is no better. Washing never comes out completely dry. It always has to be fully aired, sometimes more than others. There is no consistency in how wet or dry the clothes come out. Avoid at all costs.

On 11-29-2014 we were washing our laundry and our whirlpool washing machine started making a really loud noise so I went to investigate the problem. I open the bottom part of the washer to find out that the whole cement block to balance the drum was on the floor of the washer so I called the 1800 number on the machine and no one at whirlpool corporation wanted to even help. No one said sorry. No one said Let me see if I can help. No one. Every one I talked to they cant help at all. No one apologized once about the poor product that whirlpool sells and the defect that their products has. My washer is one year and one month old. So I can say truly with confidence that whirlpool product are the worst in the world plus their customer service even more. It is very sad after we paid all kind of money for our washer now I have to buy another one after one year and one month. Very bad customer service.

My old GE was better. I have to clean my Whirlpools filter once a month due to hard water - was wondering why my plastic cups had a white film - that was why. I have to put the knives and forks with the points facing up. My old dishwasher I could put the silverware in any way I wanted in the silverware compartment. My old one was quiet/my whirlpool I can hear it from the bedroom????

Whirlpool is not what it was before. I got this set with new house... They are very poor construction. They are not even close what I have before the LG. After 6 months I begin to have problems with the dryer... Technician come two time to fix the problems. Quality of washing is OK though... That going to be the last time I got Whirlpool products. For sure.

I bought a model (W10632082 A) dishwasher, and the top shelf is very flimsy, the dishes and glasses do not get clean, even after I fully removing any food soil from them. The dryer does not work. The dishes come out wet and with water spots. It is very noisy, and the water cycles are programmed to run upwards to three hours!!! The basket for the silverware is designed to be hung on the door, this basket falls off easy, and you cant use the left side because the normal size of the spoons or forks, get in the way of the dish washing soap reservoir, making it difficult to close the door. Do not buy this product. Horrible!!!

In June 2003, I purchased a Whirlpool Gold Conquest Side-by-Side satina finish refrigerator (Model Number: GAS6SHAXLL03; Serial Number: SP1452552). The ice-maker has always had freezing up issues which I never complained to the company about. It has made weird noises (nothing major) but was already out of warranty. I paid $1,600-1,700 for it. I did not have the money to pay for repairs and I am sure that the repairman would have never found the problem. Two days ago, there was an electrical smell in the house. After an hour or two, it started getting stronger and stronger so my husband looked at the fridge. There was smoke pouring at the back of it so he pulled it away from the wall and we unplugged it. Surprisingly, the plug was not hot. Had I not been home, it could have caught fire, burned the house down and killed my dog! I am furious about this. When I called, Whirlpool says, That model is not under a recall. Would you like me to transfer you to service for repair? Really? Those big corporations dont care! There needs to be a recall on this because I have seen this same problem many times on blogs and forums. Well, guess what, I used to be a Whirlpool fan, not anymore! Now, I went and purchased a new refrigerator, and the brand name is Samsung! I recently bought a Samsung front loading washer and dryer and they are great. It looks like the Whirlpool dishwasher in my kitchen will be next! I bet Samsung makes a nice dishwasher.

Extremely disappointed!! We purchased this water heater about 4 years ago and for the past year we have to manually turn on the burner. Its been a nightmare! We called Lowes to purchase the parts, but they do not sell the parts. There was a nine year warranty. Our last water heater lasted about 11 years. Its such a shame that this one is giving us problems just after 3 years. Im really considering just buying another one. I dont want to continue struggling with this one. Its been a bad purchase and coming to find out that Im not the only one with this problem. If its a defect Whirlpool should at least replace them for the inconvenience. They should take responsibility for selling defective products.

Refrigerator model WRF560SMYH purchased 22 months ago will not defrost automatically. When ice builds up on the back of the bottom mounted freezer, it creates a terrible noise. Only quiets when we manually defrost the ice with a hair dryer!! 4 service calls from the warranty company has failed to solve the problem.

Piece of crap! Approximately 18 months of aggravation. Clothes don’t come clean, leaves residue on them. Just absolutely the worst experience I have had in six plus decades of doing laundry. When next I get a washer...it won’t be a Whirlpool or anything made by the company. There should be recalls on these washers.

I bought new hot water heater. I installed it did and it did not work. I called them, and they sent a new part. A service man installed it, and it still did not work - he was unable to get it working. They said my gas supply line 1/2 od was too small. I had it replaced to 5/8 od 1/2id, and it still did not work. I called them again. They offered to send more parts and try again. This is a brand new water heater, never fired. I asked if they would give me a ra number so I could return it to the store. He would not give it to me. He insisted he send some one out to try to repair it. Meanwhile I have had no hot water for 2 days. He told me do what I have to do and hung up on me. So I removed the heater and took it back to Lowes, where they were glad to give my money back. But still, I lost a day of work and paid the gas yo bring it back. I went to home depot bought a GE hot water heater. I had it installed in about 15 minutes and it is working fine.

My washer worked less than a year. I finally called Whirlpool and they basically said, were a big company and you must for the rusty, broken drive shaft, pay for all new computer face plate, and service repair. I contacted the FTC and they told me they needed more complaints in order to make them do a recall on Cabrios. Good luck!

I have purchased a Whirlpool Washing Machine Mode W/P WM ROY 6212SD(31089) Sl.No.INF 153400517) GRAY/CHR TN 6.5 on 05.12.2015 with two years warranty on complete washing machine. The warranty period over on 04.12.2017. Exactly after over 3 months the machine start giving noise and we had been in touch Whirlpool and registered the complaint during last week of March 2018 and their local service center people visited, charged Rs.500/- service charge and informed that the machine to be taken to their service center to ascertain the complaint. After over a week informed that the machine complaints of Tub Support, Seal, Bearing, Drive etc. and the estimate is Rs.5,900/- including transportation (hardly 6 kms). The machine cost was only Rs.16,900/- then. I am surprised to know that just after 3 months of expiration of warranty the machine went wrong and the cost or repair costs me Rs.5,900/- is very huge. I hope the concerned will examine this.

I have spent 30 minutes trying to change light bulb under the oven and get the cover plate back on. I watched the film on how to do it, it was amusing to watch the struggle to get it on. It was amusing to say the least. Whirlpool watching it??? I do not believe whoever designed this worthless time consuming light cover never tested it one time, or it would had been more user friendly. It amazes me what kind of trash they can build for us consumers to have to deal with at times. Tomorrow this overhead piece of junk is coming out and being replaced by a non Whirlpool one. I am going to get a tractor and smash it into little pieces and put on side of street with a note saying this is what happens when you try for an hour to change the bulb.

1st range arrived in June and would not heat to temperature. Sensor and control panel replaced. After 3 techs Whirlpool agreed to replace in September. 6 weeks later new range arrives. Protective film stuck to the lettering and when you try to remove it the lettering comes off. Chunk of enamel missing off inside oven door and defect in the glass cook top. Fast forward to today. THIRD range delivered. Same issue with the protective film and gouge in chalking around cooktop. Leons has been fantastic. They are replacing it with an entire new brand!

[Model WTW6300WW0, Type 580] A few years ago Whirlpool goofed - they left out the Perma-press cycle on a high-efficiency washing machine model.We noticed the absence of Perma-press (or Casual as it sometimes now called) on the shop floor, and were assured we could arrive at the same results with the dizzying array of buttons that allow the consumer to tailor the cycles to their wash load. It turns out that it doesnt allow this. Buttons are disabled on some of the cycles, thereby preventing recreating a Perma-press cycle. No amount of prodding... Whirlpool has provided me with an override for the combination of a normal wash and a gentle spin that comprise a typical Perma-press cycle.On contacting Whirlpool about the missing cycle, they claim consumers no longer want the Perma-press cycle. Puzzled by this statement, I returned to the showroom floor to see for myself. All the washers have Perma-press cycles. Whirlpool goofed with this model. They left it out. They have not provided a replacement machine for a consumer who blows this whistle on their goof. Among the solutions their customer support DID provide: add softeners to the rinse cycle and add dryer sheets to the dryer to reduce wrinkles [by purchasing a high-efficiency machine, we aimed to reduce waste, not increase it]. Among their invalid suggestions: choose the Casual cycle [there is no Casual cycle setting on this machine]; choose Normal cycle, then set spin speed to low [this machine disables the low speed choice on the Normal cycle]; on this machine the Perma-press cycle is renamed Delicate [Wrong. Delicate only swishes clothes back and forth, not robust enough for business shirt colors and cuffs]; on this machine the Perma-press cycle is renamed Colors [Wrong. Business shirts come out too wrinkled on Colors]. There has been nothing I can do to convince Whirlpool that they produced a lemon in this model [Model WTW6300WW0, Type 580] and should replace it with a normal washing machine. I have tried for years, only for Whirlpool to come to the same conclusion: its the consumers problem now, not theirs.

We purchased a new bottom freezer Whirlpool refrigerator 4 years ago. For the past year we have had problems with the freezer frosting up. An appliance repairman told us the seal needed replacing. This was done with no success. He states there is nothing he can do for it. The refrigerator runs all the time and the freezer is unusable.

Four years ago, we remodeled our kitchen and purchased the Whirlpool Quiet Partner II dishwasher, with a one-year service warranty. To be fair, we have not had a problem with the operation of the dishwasher, but rather, the quality of the dishwasher. Within the first two years, the front panel of the dishwasher started turning brown and rusting through from the steam escaping the dishwasher. The labels on the operating buttons have peeled off, again, from the heat of the dishwasher. The upright spokes on bottom tray, that hold dishes and etc. in place, started rusting through and breaking off. Guides which allow top drawer to slide in and out and hold drawer in place, have weakened, so drawer is constantly dropping or sagging.I have had other dishwashers that have certainly lasted more than four years but was encouraged by a Home Depot salesman that this was a great machine for the price! I should have paid closer attention to that for the price part. In any event, I called Whirlpools customer service department, believing that in this day and age, SOMETHING could be done to help with these issues and was told, quite succinctly, that there was nothing Whirlpool could do. I asked about standing by the integrity of their product and got no response to that either.I am an associate with American Girl, a company that stands by the quality of its product FOR LIFE. To be told by a customer service rep from a much larger company, that there was nothing they could do to help me, completely blew me away. I have taken pictures that are pretty indicative of the quality of this dishwasher and will be going online to warn other consumers against purchasing Whirlpool products.

Smelled strange odor in laundry room area.. Noticed plastic panel to Whirlpool electric water heater controls was melting and immediately closed breaker to the heater.. After inspection of heater control panel, noticed all wiring damaged and burnt causing burning smell.

Refrigerator ice maker quit working. This is replacement fridge for first refrigerator that quit working same model. This one has electrical burn marks inside behind a panel. Whirlpool says this is normal. How can burn marks inside a refrigerator be normal. If house or fridge catch on fire will be suing Whirlpool. Ice maker and water valve replaced. Still not working. Maybe it has to do with the burn marks.

Bought on 9/11/2014 and installed by Lowes installers on the 15th. It quit heating two days later. Called Lowes and they said I would have to call Whirlpool. I did. WP had me metering with a multi-meter until found OTC button was tripped. Then they suggested I troubleshoot the elements and sent me a video. I called Lowes and they said they would replace. Later they called back and said WP would not give them a RA number and for me to call them. I did and the rep after much arguing directed me to call their factory authorized service, A & E. I did and they said it would be 33 days before they could come out. I hung up and called Lowes who called back later and wanted me to call WP again. This time they said they did not have a repair service close enough to come, but I could try buying the lower heating element and replacing it to see if that worked. I said no, the heater was brand new and they needed to fix it. Their next solution was have me contact a local plumber and arrange to troubleshoot, me pay the plumber and then send them the bill. They would reimburse me up to $100.00. Not acceptable and now the button has to be reset every few hours and the water gets scalding hot while it is heating. I called Lowes and they said they would get back to me, but I have little hope of a resolution. Product number is ** SN is ** Model is E2F50HD045V. Bought at Lowes, Lindale, TX.

We bought a Whirlpool front door open washer machine from Best Buy on Oct. 2, 2011. We didnt start to use until our basement got finished. In November when the basement was ready, we found out that the machine didnt work at all. We called A&E factory service as suggested by Best Buy. They sent technicians 3 times in 2 months to check the machine. Now, it is 3 months later since we purchased the machine, the machine is still not working. We contacted Whirlpool, and they would not exchange to another machine, instead, they told us they will send another technician to check it once again. This machine costs us $800 before tax, but until now, it is still not working. Can you tell us what to do? We called Best Buy and they said this machine is under factorys warranty. So we called A& E service, who said that if Whirlpool called them, they will tell them it cannot be fixed. However, they need Whirlpool to call them because they work for Whirlpool. Is 3 month waiting not enough for a brand new machine to get fixed? And the worst thing is we still owe money to Best Buy creditor. Please help us to get rid of this! Thanks!

Bought Whirlpool refrigerator Model GB2FHDXWS from Best Buy in July, 2012. I began freezing up immediately. Called Best Buy. They replaced it. Now the second one quit. Freezer doesnt work. Refrigerator motor works constantly. Called Whirlpool and was informed unit only has one year warranty. Got an estimate to repair it. Evidently, sealed unit needs to be replaced at $700. Will never buy another Whirlpool appliance again. Will not deal with a company that will not stand by its products.

Three years ago I bought a Whirlpool 22 cf bottom freezer (GB2FHDXWB02) & within 2 weeks it developed its first problem. Ive had service men out 3 times (on an extended warranty) for ice buildup and leakage, presumably from the icemaker, and the problem hasnt been solved yet. I tried to open the freezer tonight and the handle pulled off in my hands, nearly sending me head over heels. This thing is a major lemon!!! Dont get me wrong: I love the design! It looks good, keeps everything at the right temps & the bottom freezer is a great idea. Id buy the same design again if I could guarantee no leakage and a handle that wont separate from the door. Now Im having problems getting the repair service to come out here again, despite the warranty. Meanwhile, the fridge is leaking onto the wood laminate floor causing damage. I just replaced an ancient dishwasher & my old Whirlpool glasstop stove after its oven failed. I cant afford a new fridge too.

For the last month, in order to wash dishes, we have to start the dishwasher normally. The water will begin to fill the tub and then stop and all the display lights go out. We push the cancel/drain button and the dishwasher empties the water in the tub. We again, push the desired wash cycle button just like the first time and the dishes wash normally. We have purchased at least two of this same type dishwasher with the utensil holder in the door from Whirlpool in the past, with great satisfaction.

August 10 2014, I purchase a new Whirlpool HE. Monday cant wait for the delivery of my new washer! Im ready with my HE detergent & 2 loads of dirty laundry. Tuesday, I want my broken old Kenmore washer back! My kids clothes came out dingy. Did a second rinse & spin but didnt help. Second batch had to be rewashed. Some areas were not even wet. Had to pause it to add more water to & again to rinse it. Plus I had to mix my softener into a cup of water to add it on rinse because I forgot the rinse ball, unlike the old washer where I add into dispenser & forget about it. So unhappy & dissatisfied.

Whirlpool Cabrio Top Load, Short Agitator to protect clothing, cost reasonable, on sale $800.00 both (Aug. 2013) - Sears credit no interest. Moved, and had to sell after a year, but I anticipated a long life r/t rating/reviews online. One Problem: no setting to soak clothing that may need it. I bought the largest Whirlpool Cabrio to make sure my Queen bedspread (heavy blanket type fur on one side) would fit. Because of the short agitator I could have bought the smaller one I discovered. I could fit 6 regular side and 4 beach heavy beach size towels in it easily, or two Queen quilts in at a time. I rarely needed an Xlg water setting. The dryer had a steam only setting but I never tried it because it was set up in the apartment when I arrived and the delivery people were not very bright. Put the Dryer farthest from the vent, washer farthest from faucets, and put hot and cold hoses on opposite spigots. I did not want to chance they set up the steam section wrong, as well. I moved across country 1 year later, but have trust the W/D would do well. My last Sears brand (made by Whirlpool) only had one minor problem (on warranty) and lasted a good 8-10 years before moving and selling them to another couple. They were still in wonderful working order (front loader).

I purchased a Whirlpool front loading washer from PC Richards in January of 2010. The warranty was only for one year (the washer was new, not used). The model # is WFW9050XW. Anyway, the washer had to be repaired by PC Richards twice in the first year I had it. Once because the belt that makes the washer spin broke, then because the pump got clogged. Unfortunately, when you wash your clothes, your socks and underwear can get sucked into the pump. After that warranty expired, I purchased a warranty from my utilities company (PSE&G). I have had to contact them four times for repairs to this machine. The most recent problem is my clothes are still wet after the washer stops. I actually have to wring them out by hand to get the excess water out. When I contacted my utilities company about servicing the washer, I was informed that if the repair is more than the washer is worth they dont have to fix it. I canceled the repair and now got to the laundrymat. I figured if I wait until the end of the year, maybe the repairs wont seem excessive. I contacted Whirlpool about the problems and was informed that I should have been using a garment bag to wash my socks and underwear in. More or less the person I spoke with made it seem as though it was my fault the machine sucked up my underwear and socks. I, on the other hand, disagreed with her. I told her the washer should have been build so that it would not suck up these items. I was so totally pissed off I ended the conversation. I also informed her that I would not be purchasing any other appliances manufactured by Whirlpool or Maytag as they are affiliated. They obviously have no integrity when it comes to their product. However, I am totally baffled. Why do the Maytag machines work better and last longer than the Whirlpool machines? The washer I replaced was a Maytag. I had that machine for 17 years!!!!

We purchased a Whirlpool Cabrio washer in 2009. It makes awful sounds during the draining and spinning cycles, has started leaking in the past month and now, several error codes and will not finish a load of laundry. We have a family of eight and thought that we had bought a very dependable product for what we need. Boy, we were wrong!

My first washer a Sears Kenmore lasted us 25 years before giving it to our son who used it for another 10 years. This machine is compatible with that one. Both are simple with a few of bells and whistles. That is remarkable in todays gotta have all of the fancy gadgets mindset. The Whirlpool machine does a very good job of washing clothing...period!

I purchased Whirlpool top loading washing machine model # WTW57ESVW less than 2 years ago. It stopped working yesterday. I had a trusted professional repairman evaluate it today. The motor needs to be replaced after less than 2 years?! The customer service reps basically said sorry. I should have purchased the extended warranty. Is it not reasonable to trust that a Whirlpool washing machine motor should last more than 2 years.I am very unhappy and very angry that Whirlpool will not stand behind their product. The last customer service rep I spoke to suggested she could send one of their repairmen and replace the motor at a cost to me of $299.00. So, after less than 2 years, I am offered an amount to pay of about half the cost I paid less than 2 years ago for the brand new washing machine. My home is full of Whirlpool appliances. I have been a good and loyal customer for over 30 years. I am very angry and upset with Whirlpool. Please explain to me why it is not reasonable for me to trust and believe that a Whirlpool top loading machine that is well cared for and not abused in any fashion should last longer than 2 years? Is this being a loyal Whirlpool customer gets you, I should have purchased the extended warranty”? We are talking about a motor here, not a fabric or bleach dispenser that breaks. Although, those parts should not break either, there is a big difference from something like that and a motor. Please contact me as soon as possible at either number listed above. Thank you.

Bought a nice house in 2012 which has a Quiet Partner 3 Dishwasher. About twice a week it has to be reset pressing buttons because it blinks at you when you press start. Control board was replaced a couple times since we bought house. We just put up with it. The tub has a manufacturers defect in bottom where the plastic is so thin it finally cracked and over time water trickling out went to wall. Then ruined an area in finished basement ceiling. Ive used a couple different things to stop the leak but it always starts leaking. Customer service says its not under warranty so will buy a new dishwasher. But not Whirlpool or Maytag. Same company now. Dishwasher is a total piece of crap.

Whirlpool Cabrio Platinum WTW8500BWO - It doesnt wash anything very well. I hate it. Dont want it. Wish I didnt buy it. I do all kinds and sizes of loads. My clothes come out dirty - I have to wash my clothes 2 or 3 times.

Hi Folks, so today I had the pleasure to speak to Whirlpool regarding a repair bill on our washing machine which now has a bearing failure and estimate to repair was 1279.00. Its 6.5 Yrs old, just out of extended warranty and cost me with the pedestal a total of 1250.00 when new. I explained that in the 6.5 since I have lived at this house where we spend all new Whirlpool Gold Appliances, half have now failed. Range Microwave, Dishwasher and now the 1250.00 front loader is dying a slow and agonizing death with a bearing failure. Just so everyone understands, the estimate is from an official Whirlpool repair service that was booked through the Whirlpool website. Other repair folks just would not bother to look at it when I told them I believe the bearing was going bad.The repair man that arrived was professional and on time. However, I had a hard time understanding how a 6.5 Yr old washing machine would be considered beyond economical repair by costing 1279.00 to repair. Labor was 250.00 which I thought was fair. Time, etc. But parts made up the difference in cost. So later in the day, I spoke to Whirlpool and they offered the equal new washer for what would seem an excellent price. About half off. Wow, I thought that sounded good. So I asked if my existing pedestal would work with the new washer and it did not and I would have to pay for one. Regardless if my old one was fine or not.So, they offered a discounted rate from new at another half off. Total approx 800.00. So, I asked the Whirlpool rep to hold on and I need to check with my wife if she wants the replacement. She uses it as much as I do and wanted her thoughts. She checked the model on the washer and pedestal and with the local Home improvement store, they have it on sale for both units (washer and pedestal) and its about 50.00 less?Consequently, I called Whirlpool back and explained that it does not move the needle to regain my trust as compensation on a 6 yr bearing failure, failed dishwasher and range microwave they offer what a distributor of their product can offer for less as a package? Really? I mean, the Home improvement store is not in the business to lose money. Now, I am having a hard time understanding my own failure to have trust in a brand I used to have with my previous house.My mom had an old Whirlpool washing machine that lasted 25 years before she and my dad gave it away. You know, the old white top loader they used to make back in the 70s. Sheet metal, made a racket and never broke? Oh yeah got the clothes clean too! I dont know what to make of it anymore. So, I will just wait till it dies and take my hard earned money and spend it on another brand in my next house which we are going to move to soon. Maybe I can feel nostalgic and find my moms old washer. Its probably washing someones rags right now and getting them clean. It must be 35 yrs old by now.I dont expect to get anything for free. Its out of warranty, so I need to deal with the consequences, but there are steps the other party can take to help remedy the situation. I think they tried and it was genuine but in my thoughts its just not enough when your local box store is offering the same. When you develop a brand to extend a message of trust in quality and value, you need to have quality and value all the time. I suggested they help with the costs on the parts. I would certainly pay for the labor. Parts cost little to the manufacturer. Unable to help that way. I thought it was cheaper for them too. Guess not. Its come to be a throw away washing machine at 6.5 yrs and I am Infinitely disappointed. I just want my washing machine to work as well as my mothers old one and have the possibility to fix once in a while when needed.

I had a Whirlpool Natural Gas Water Heater professionally installed on 2-27-2107. This unit came with a Honeywell controller and thermopile assembly. Today is 05-18-2019 and the unit is not inoperative. The pilot is lit but the burner wont light. Here are the issues that I have come across so far: When I go to the Whirlpool site there is no direct link to Whirlpool water heaters, just kitchen appliances and washer/dryers. When I click on parts and accessories link it gives links to washers, dryers or pedestals. Again... No information about water heaters. I scroll down to the bottom of this page and I see a link to All Replacement Parts When I click that it takes me to another site managed by RepairClinic. When I enter the model number for the water heater it says Not Found. I entered the part number for the thermopile on the tag on the orange wire #321165-002 and 100078039 and again it returns as Part Not Found.Its obvious that Whirlpool is putting little effort into supporting their water heaters or their customers. I called their support line and they were able to order the thermopile assembly for $55 plus $27.95 in shipping to get it here by Tuesday. Today is Saturday. So that means almost 4 days without hot water. And since this water heater was a warranty replacement for a previous one that went bad they will not cover the cost of replacement parts for the thermopile. Lesson learned: No more Whirlpool purchases for any of their appliances.

Whirlpool customer service is non-existent. I have a Whirlpool microwave that burned up after two months of use, and they sent over a technician twice, in the past three weeks and it is still not working. Now, I am being told that it will take another two weeks before the correct part is found, and the technician is sent here again to fix the problem.I have no microwave now, for what is going to be about 5 weeks, and that is only if they get it right this time. Whirlpool wouldnt approve for me to have it traded a trade for a new one at HH Gregg where I purchased it in Aug of 2011. HH Gregg only has a 30-day return policy, and it went bad after 60 days.

The reason for the call was to find out how to file a claim after replacing the ice maker and paying for it the 3rd time, they were very argumentative and would not listen to me about the design flaw in the wire harness that burns up the motor for the ice maker. I found out about the design flaw from talking to the repairman that replace the ice maker who works for Dick Kearsley Clearfield UT. He told me that Whirlpool knows about the problem for the 22 cubic foot and 25 cubic foot refrigerator and that is why they have 2 different new wire harnesses in the box for replacement of the old wiring harness.

Whirlpool Cabrio top loader washer - I am writing to really complain about a washer I bought there at Metro. The people were great BUT this washer has been a REAL DISAPPOINTMENT!!! It is only 4 years old and I have had to have them come and replace the top of the machine. It has rusted around where you put the bleach, the soap. It leaks underneath the machine, its rusting on the bottom of the machine horribly. SO DISAPPOINTED!!! We bought all WHIRLPOOL products - washer and dryer, stove, microwave, dishwasher.What is it with these things? They rust so easy. I had a washer before this one for 14 years and it never did this. I guess things are not made with the same quality as years ago, but I will not ever spend my hard earned money on WHIRLPOOL AGAIN!!! I guess I will have to put up with this machine till I can afford to buy something else. VERY DISAPPOINTED CUSTOMER!!!

I purchased my Whirlpool French Door Gold Series fridge for $2179.00 in November of 2013. We just had moved into a new house and wanted a fridge that would last a long time. In the past couple weeks the freezer has stopped freezing and after calling Whirlpool I was told I was out of luck and would have to pay full retail price to get the problem fixed. This will be the last Whirlpool product I ever buy.

whirlpool Cabrio Washer - I replaced my front loading Duet with this, thinking I was done with front loader. Designs are set to fail, liked the idea of no agitator, thinking can clean a lot clothes at once, boy was I wrong, heavy loads wont spin dry, forget sheets or blankets. The machine just stops, leaving everything soaked and you basically screwed, you can invoke a spin cycle but to help make rinse and spin out, sooo disappointed. Whats wrong with the designers of this product? They didnt try sheets to see if it would even work. I am far from over loading this too. Dont buy this.

5 years and 11 months ago I bought a 50 gallon gas, Whirlpool hot water heater with a 6-year warranty from Lowes. The 2007 water heaters were on sale, so I paid $329 for it. Within 6 months, I replaced the gas valve, and a few months after that, the thermo-couple went out and I replace that. Each time I called Whirlpool and got return authorization numbers for the parts, I still ended up paying for the parts plus labor. A year after that, the igniter went out and I had that replaced. Last year (the day before Thanksgiving), the thermo-couple went out again and I had to have that replaced - and it cost me for the part plus the labor - even though I had a return authorization number. I also replaced the water line connections/hoses to the water heater at that time. The customer service rep for Whirlpool told me at that time if I had another problem with the water heater, they would replace it for free - and the warranty was good until Dec 31, 2013 (this year). NOTE: Every plumber that has come out to fix the water heater and replace the parts stated that they see a myriad of problems with Whirlpool water heaters. They said the parts like the thermo-couples, igniters, gas valves, etc are poorly built and they replace them all the time. On Christmas Eve 2013 (two days ago), the water heater started leaking from the top by the valves - and so much pressure had built up in the heater the new water hose connections burst, spewing water all over the heater closet. I called Whirlpool the day after Christmas (today). At first, they told me they would not replace the heater as it was not in warranty and then I told them what I was told by the service rep last year. She finally agreed that my heater is indeed under warranty and gave me a replacement authorization number but she told me my warranty did not cover labor. I called Lowes. At first, they told me I would have to remove the old hot water heater myself and bring it back to the store in order to get my replacement. I am a 59 year old woman and I take care of my brother, a disable veteran. Although I am in good shape and healthy, I dont have anyone to help me get the gas and water disconnected and help me lift it into my Suburban. The man at Lowes agreed to bring out the the replacement heater and pick up the old one at no charge, but I will still have to pay $299 plus the cost of new hoses to have it installed. By the time the replacement one is installed, I will have paid a little over $1200 for a $329 water heater. I could have installed a tankless one for that, but I cannot see spending that kind of money right after Christmas. If I have one issue with this replacement, I will install a tankless water heater - and it will not be made by Whirlpool or any of its affiliates. My recommendation would be to steer clear of Whirlpool and their products.

We purchased a cabrio washer about 3 years ago and have had trouble with coins getting into the drain pump and cracking it. We have repaired this at least 5 times and dont understand why the washer allows this to happen. Yes we do accidentally leave coins in our clothes but we have not had this problem with other washers. Clothes also have odor.

Thermocouple failure on a Whirlpool water heater - We are having trouble finding the part to replace it because the thermocouple is threaded left-handed, and Lowes does not seem to have any replacements in stock locally. Meanwhile my tenants are without hot water, and my repair bill is escalating due to labor.

We purchased our first front-loader washing machine (Whirlpool Duet WFW9250WW00) just over two years ago. Since we purchased it, it has torn clothes and we have replaced the drum baffles twice (this would be the third time, but we are throwing the washer out), the drum seals twice (another place clothes can get caught). I had adjusted my washing (maybe I overfilled the washer, maybe I was using the wrong spinning speed), but every so often clothing would come out with holes or torn. The drum baffles must come loose before they come out, and clothing can get caught underneath them (I think that is where the tears occur). It has happened at least once a month and I had spent a fair amount of time trying to figure out where the clothes got caught and torn. Many people complain about bad smells from the washers (which I never had - I like the Tide with Febreeze detergent and every so often clean it with bleach or Affresh), but never torn clothing. I would really like to use a front-loading washing machine, but we are going back to the top loader - we cannot afford the clothing tears. I have seen that many people replace baffles (not many speak of clothing tears) and maybe in the future this problem will be addressed. But in the meantime, I would stay away from Whirlpool front-end washers. (GE makes some nice top loaders - and in 40 years of washing clothes and only owning two other washers, I have always thought washers to be an appliance that would last 15 years or longer with very little maintenance or trouble). I believe that I really tried to make this washing machine work out, but it got to the point where my husband did not want to wash baseball uniforms and other irreplaceable clothing in our washer.

I have the stainless steel Whirlpool Gold appliances. They look beautiful but do not work for long. For one, the dual burner never heated properly on the cooktop. I just worked around it. The oven vent on the cooktop left brown marks on the stainless facade attic top by the clock. Ive read some have melted this area. Then after 2 years, the entire front glass door and handle fell off when I opened it. It not only fell, but the cheap plastic lip that holds the door on cracked so it is impossible to get back on. So, since I cant afford a new stove. Im stuck with this horrible looking mess in my kitchen.

I purchased a range top from Lowes and a month and half my burners go out. I call Whirlpool and a service technician came out. Said that he cant repair the stove because a bug had burned out the burners and he cant repair the stove. I call Whirlpool and they told me that voids my warranty with them even though my stove is not even two months old that will not repair it and I will have to pay for it to be repaired. I asked Lowes and they told me that they only take back big appliances back before 30 days. Now I am stuck with a stove that I paid 700.00 for that does not work and I have 4 children to feed. I am sickened on how Whirlpool can do this to a hard working family that just wants a good stove. I hope this helps another hard working family. Do your research before buying from Whirlpool. I wish I would have.

We purchased our suite of appliances from Home Depot, this was a great experience. Unfortunately that is were it stopped. Our 1st refrigerator caught on fire in the electrical within the unit. We got a 2nd refrigerator sent to us and it came damaged. Then they sent us a 3rd refrigerator and it caught on fire in the electrical as well. Weve been dealing with this all since August 27th 2019 and here its now October 14th 2019. At this point I feel this model of Whirlpool is truly unsafe.

I purchased a Whirlpool electric water heater from Lowe’s in 2007. It lasted 2 years until a faulty weld on the tank started leaking and flooded my basement. Whirlpool did replace it. However, my second water heater did the same exact thing in a different location on the tank after 2 1/2 years. It also flooded my basement.I am now on my third Whirlpool water heater in 5 years and the one I have now has a bad thermistor. It has cost me about $225 each time the water heater has been replaced. In my opinion, these Whirlpool water heaters are junk and their quality control needs to get out of the break room and start doing their job. Never will I purchase another Whirlpool appliance.

Bought a higher end Gold Series French door refrigerator. Immediately the door would malfunction and the the piece that pops out to seal the gap between the 2 doors kept piping out when the door opened...They came out and replaced it which did nothing...The repairman said we have to open the door slowly...Give me a break...Have a older cheaper model that is almost the same and its always been flawless.Now in year 2...the whole system shuts down out of the blue and thaws everything then suddenly works for a few months...Repair guy says cant do anything if he doesnt see the problem...Just got back from long vacation...We turned off the ice maker and emptied...Returned home to damaged wood floors and a bin full of ice...System reset when it restarted and started making ice...2 years old and we have a Samsung on order and the Whirlpool is going in the trash...Weve had many whirlpool products and the defects are getting worse every year...Absolutely done with them!

The washer was 5 months old and broke. Three service appointments and multiple phone calls, it still wasn’t fixed. Whirlpool sent rusty parts out to my home and that was the second excuse for not fixing the washer. The poor service guy must have been 70 years old. Hello, how do washer parts get rusty when they are not even used and are kept in a box?

Whirlpool WRT351SFYW 21.1 cu.ft. White Top Freezer Refrigerator - Energy... Puts out a very irritating high pitch noise, unlike my previous Whirlpool Refrig. The old one was perfectly quiet. I believe Whirlpool is going down hill in every way. WP is buying refrigerators from 3rd world countries and slapping the name on them. The delivery people were very rude with me when I was unable to give them a tip, even though I had to supply my truck to shuttle the refrig. up to my house and help them unload it. I also had to go and find them when they would not follow my directions to my house. So, they kept the wrench I loaned them; they did not have their own tools for the installation. And they refused to return it when I asked them to do so. Denvers customer service refused to respond in any way to my requests for information or complaints about the noise and delivery. Finally, their head office contacted me a month or two later, and the customer service person had initiated the discussion in argumentative attitude despite my saying I did not care anymore. I gave up on them and dont expect anything from Whirlpool anymore. While she told me that there are standard levels of acceptable noise that come from their refrigerator, she refused to acknowledge that they are not my standards, and I am the customer. Besides, I had an older Whirlpool refrig. that did not make any noise. I am sorry trusted WP. When I tried to upgrade the old refrig. - it was an expensive downgrade! Buy LG or Amana - wished I did!

Ive had my Whirlpool Gold for over a decade and absolutely love the quality and performance of the unit. No maintenance issues whatsoever throughout the years. I recommend this washer to everyone I know and continue to enjoy the performance and reliability of Whirlpool. I will continue to buy this brand every time as needed.

Whirlpool Cabrio HE washer - Purchased my set in 2007. Has not worked properly most of the time we have owned. Lid locks our clothes in when the machine malfunctions and we have to barter with the machine for hours of Google suggestions to get the clothes back out. Still dirty. Or still soaking wet, not spun. Ive never seen so many error codes from one machine. I would never purchase this brand again. The only pro is the load size, which trust me - we have spent more time, water, energy & $$$ with the washer not properly working than the large capacity has saved us.

This machine needs to go back to the engineering dept. There are too many engineering defects to mention. My Cabrio washer and dryer was delivered October 11th of 2017. It is just my husband and myself so laundry was scarce. I have been unhappy with the washer since the beginning and just recently decided to try and solve the problem. I contacted Whirlpool first and was told these machines have great reviews and nothing is wrong with them. When I started describing the flaws, there was one excuse after another and the person from Whirlpool blew me off. The flaws... all begin with not cleaning which is caused by design. The water level, even with the deep water setting, does not even cover the amount of clothes in a small load; the agitator is so small, there is no effect on agitating the clothes; even with using a SMALL amount of HD detergent, there is always soap residue on the clothes because of the lack of water; and last issue but not final is the load going off balance. The machine will walk all over and error codes according to the repairman need to be cleared so must call if it happened again. Well, the very next load it went off balance again. I did not call because I would have the repairman living with us and I am not willing to set up a bedroom for him or feed him. So, Whirlpool does not care if their product needs redesigning, they only care about selling their product and then the consumer is on their own. Basically the same train of thought from Best Buy where we purchased the machines. Best Buy would be happy to sell me another laundry set... per the store manager but that is all he could do. Will I purchase from Best Buy again... I think you know the answer to that. If they cannot stand behind a product they sell, then they can keep everything they sell, no more money coming from my checkbook to them ever again. Someone, whether the manufacturer or the retailer, should be willing to stand behind their product. But, no one cares. Bottomline, do not believe the ratings on the Cabrio washer. This machine has design flaws that cannot be corrected.

Cabrio Washing Machine - I purchased my washer and dryer in May of 2008. I had problems with sheets, towels and pants getting very twisted and tangled, but I just attributed that to a design flaw. My problems really began in January 2013 when loads were not level all the time. It didnt matter if it were 1 shirt or a load of towels; you had to stand by the machine and it took forever to finish a cycle.On 1/11/13, the first repair was the rods that kept the drum stable. $260.82 later, it worked again. On 2/16/13, the washer quit working. On 2/18/13, the repairman was back out. It needed a lid lock switch. It was $87.14 that time and he would be back when the part arrives ... There was still no washing machine. On 2/21/13, he returned with the lid switch and replaced it. That was $178.04 but wait, there were still other error codes so there was no working machine.I refuse to pay anymore as I now fear I will be buying a new machine after spending over $500 in less than 6 weeks, but Whirlpool did the right thing when I called and they agreed to repair the machine. They wanted a different company to come diagnose the problem (the machine gave an F50 and F51 error code to the repairman here on the 21st), so I have to wait for another repairman to come and look at the same codes flashing on the LED readout.On 3/1/13, the A&E repairman that Whirlpool sent out arrived at my house. I have been without a washer since the 16th of February. He diagnosed the problem and said that it is a $1,000 repair! I called Whirlpool and asked for a new machine, instead of throwing more money at this one. They informed me that if I didnt like their offer, they wont do anything then. I agreed to the repair.Parts started arriving at my house. On 3/13/13, another A&E repairman came out and started to fix the machine. He informed me that there was more wrong than the first guy thought, but he had the circuit boards so he would get it going. On 3/24/13, the washer quit working again and was flashing an F51 error code. This is the biggest piece of junk I have owned in my life. I have missed 5 half days of work since January and there is no end in sight. Why is Whirlpool allowed to get away with such an inferior machine?

Am posting in regards to a brand new dishwasher that I purchased the first part of February 2020 from Menards. The dishwasher I bought is Model # WDT730PAHB and Serial # F94519386. I had the dishwasher 10 days and it stopped working after running only two times. I checked the breaker box and all electrical connections to the machine and it was getting electricity, but would not turn on at all. I called the store to return it and they only have a 7 day return policy. Since then Whirlpool has been contacted and I have had two service calls from Whirlpool. The mother board has been replaced (which I waited two weeks for the part & five hours for a service man) and still it will not come on. Now I am waiting on a wire harness, ordered on March 4th or 5th and still not here. I completely understand wanting to fix a broken machine, however this was a new dishwasher that only worked for 2 washes. I have now been without a dishwasher for almost 2 months, which in light if our current world situation isnt a huge deal, however this is a time when sanitation is very important. I feel like Whirlpool should offer to replace my new machine with a new machine and not something that is refurbished. At this point it is costing more to repair this machine than to just replace it. Every time I call Whirlpool I get the line of we have to repair it. Give me a break. Take care of your customers!!?? #neverbuyawhirpoolproduct

BUYER BEWARE!!!! Dishwasher less than 2 years old and pump & motor assembly went out. You would think and hope that an appliance would last longer than that... Contacted Whirlpool and they were not helpful at all. Will not be buying anything made by Whirlpool again...

We bought this pair, the washer and dryer, not even two months ago. I have not liked it since day 1. My clothes do NOT clean well at all. I had to wash the same load THREE times and still there is dirt on them! Just regular dirt. No oil, grease stains or anything... dirt. I even went and purchased POD detergent to make sure I was using the correct amount of detergent... Came home and washed the load again... DIRTY. Customer service says theyll send out a technician, but if they find nothing wrong, itll cost me... I wish I had read the reviews before I purchase this junk! DO NOT BUY!!!!!

I have called Whirlpool multiple times because our washing machine model #WFW9290FW has been out of service for 5 weeks now. I have been informed that I need part #W10604640, which is on back-order and they wont give me any idea of how long it is going to take to get this part replaced. Apparently, there are 96 total people who also need this part. I find it hard to believe that a company this big would not have this part on hand and they would not have any idea how long it would take to get it replaced. I asked them to give me a new washing machine for free to replace it because of the poor service and the unreliable washing machine. They told me they could give me another washing machine at 40% off, but based on the lack of follow-up and the amount of time that has passed since my initial call, I dont want another Whirlpool product. This is the worst customer service ever.

My stove is good, I have gone through 2 refrigerators in less than 8 years and the replacement is having issues. Service is a joke, customer service is questionable but trying to assist but at this point will not recommend whirlpool products.

When I first bought this machine I loved the big tub, but I was concerned that there was no agitator. It confuses me how clothes can get clean if there is nothing to rub them again. Even in the olden days they rub clothes against a board. Well my concern is valid and I believe the washing machine industry needs to go back to the old model, as this new version does not work.Here are all the problems: 1) The machine judges how much water to put in. This doesnt work. I follow the directions and outline the perimeter and dont overload, yet still it just barely puts in enough water to make the clothes wet. Im all for conserving the environment, but enough water needs to be provided to actually get the clothes clean. I would like to be the judge of how much water should be used, so I would like to be able to tell the machine if it is a small, medium or large load. I do believe that the lack of enough water is why the clothes do not come out as clean as they should and why they end up smelling (see #4). 2) There is no agitator, so there is really nothing available to help clean the clothes. Spinning them around like a maniac is not enough, which leads me to the next problem. 3) The clothes come out twisted terribly and then many times come out of the dryer wrinkled because of how hard they were twisted. I tried to select a less harsh spin cycle, but then the clothes are too wet to put in the dryer. There is no happy medium.4) Biggest problem to date: Our clothes/towels have all started smelling. You know that smell when you leave your clothes in the washer too long (like two days) and then put them in the dryer? Its that smell. The clothes/towels dont smell when you immediately take them out, but they do smell at any bit of moisture. When I dry myself off after the shower, I notice the newly washed bath towel smells like a wet dog. I have used the pods, liquid detergent and powder. I dont remember having the smell problem when I first bought the machine and used powder, so I just returned to using powder today. (Ive even tried doubling up on the pods, but the clothes still smell.)This leads me to problem number 5: When using powder in this machine, the machine does not empty the powder container completely, and so the clothes do not get the required amount of detergent. Often there are clumps left over in the powder dispenser, but not always. (This is what led me to go to the pods and liquid detergent in the first place.) But at least with powder (I use Gain) my towels dont stink after the first time I used them.I wouldnt recommend this machine. I really researched machines before I purchased this one, but they all had bad reviews, so how do you pick? And I never look at the good reviews because we all know so many people are paid to rave about products they know nothing about, or it is a company employee writing the review. This machine is a huge disappointment. I am going to try adding a rinse cycle like a previous reviewer suggested. Maybe the extra water will help with the smell. Of course this is not good for the environment though, so this whole way of making washing machines with no agitator and limiting water defeats the energy efficient goal.

My 3 year old Whirlpool dishwasher (model GU3200XTXY3), broke down for the third time. Under extended warranty with my insurance company, a repair tech was sent out to diagnose the problem. He quickly found that the heater had been continuously running (not just during drying), which caused the machine to quit working. He also found that all the wiring inside the dishwasher was spliced together, those two things=fire hazard! Because the heater was always running, it was super heating all the water used to clean the dishes. The vent to release the steam is located on the top of the door (right under counter edge). The dishwasher was producing hotter and more steam which slowly ate away at the particle board under the cabinets. No, we dont have the most expensive countertops, but Whirlpool should be held responsible for producing a faulty product with a faulty design. I have contacted Whirlpool and they claim to have mailed a claim form 3 weeks ago. I have not received it. Posted on social media about it, and was told I must only speak with the person who sent me the form. I would love to, but since I havent actually received any contact from anyone (other than a fb post) I dont know who to contact, at what number, or email!

We bought a Whirlpool Gold French Door refrigerator in 2010. Just when the warranty period passed, the refrigerator started leaking water from the bottom floor. Initially, it only leaked about once per month. But as time passed, the refrigerator started leaking more often, and now its leaking every 2-3 days. I saw many people complaining on the same problem and some of them even submitted since 2006. I dont know why Whirlpool doesnt resolve this issue in many years.