2 loads of clothes and it is broke. I tried to call Whirlpool to no avail. So I called Costco where I bought this machine. They at least talked to me. Promise to get a hold of me tomorrow. Brand new (2 days old) and this happened. Didnt even finish the second load.

Purchased Whirlpool Cabrio model WTW6400SW washer and dryer 1/7/2007. The matching dryer was dead on arrival and the second dryer motor died within a year. Washer: 1year 2 month the washer motor died. Whirlpool paid for the part and I paid the labor. The following year, the bearing went out and the outer tub was replaced (the bearing is inside the plastic outer tub - bad design. Whirlpool paid for the part and I paid the labor. Feb. 2011 had one of the F errors. Whirlpool repair tech came out as the tub would not drain and it was a wire that had come loose underneath washer - another service call charge. Dec. 20, 2011, I had an error F50. The Whirlpool repair tech came out, verified no clothes or money stuck in the machine. All clear. He called higher level whirlpool tech and they paid parts and labor to replace the main control board and the RPS Sensor. Im single and am not abusing this machine. Like everyone else who posted. I paid close to $1,000 for this washer (not including the dryer) and I have been a faithful Whirlpool customer for 3 generations, but if Whirlpool doesnt offer some kind of compensation/trade in credit to customers who purchased this (knowing that the design is bad/faulty) washer and discontinue this model. This will be my last Whirlpool. I will have lost all faith in Whirlpool. The Whirlpool service tech that I found is op notch. I will miss him if I have to switch brands. Im putting 1 star as I know this machine will not be operational for 9 years which is the minimum that I would expect. If it makes it to 6 years without another service call, it will be a miracle.

I purchased this piece of crap excuse for a washing machine, the Whirlpool Cabrio, almost 2 years ago, in September, 2015. Since that time I have had nothing but dissatisfaction about how it washes, and the extremely poor results. I contacted my sales associate early on, I was told, just like others who have purchased this machine, that it was a water-saving machine, and I needed to read the manual closely and just do what it said to do. I did that. Long story short, I am sick and tired of this machine, stopped using it, bought another machine that lets me choose how much water for each and every cycle, it washes extremely well, my clothes come out clean, it HAS AN AGITATOR, DIFFERENT BRAND, and I am very HAPPY with it! I will never ever buy a Whirlpool product again. I am well-known, have an extremely large number of friends, and I will be spreading the word that Whirlpool built a piece of crap. Never mind that piece of crap washing machine was mandated per government regulations to cut down on water, thats a bunch of crap. Users should not have to buy expensive cleaners, tote extra water to a washing machine that uses so little water that it barely covers the clothes, and no person should have to use a product like this. Never. Washed clothes from this machine stink, the odors will not leave my clothes, whites are now yellow, stained, and colors have white spots on them. Whirlpool, you have built this piece of crap, I hope you have large heapings of Karma! What a joke. What a useless company now, sell out and go play on the beach. You deserve the dirt, not your use-to-be-loyal customers.

We had the refrigerator delivered in March, 2013. We noticed a leak in February 2014, only because we smelled a musty smell in our garage, and removed the rug outside the door, from the garage to the kitchen. Then we started noticing water in the garage. It was shortly after we determined it was the refrigerator. We bought this at Lowes and they use A&E, and they did not show up for the first appt. They did replace the pan a few days later while we had to replace dry wall behind the fridge. This time around (month later) we noticed the fridge/freezer was not cooling. So A&E came out and determined its the compressor. So now we threw out hundreds of dollars of groceries, and water was leaking all over the floor again from ice thawing. I believe the refrigerator has had problems all along. We have had it for one year. I think we should be reimbursed for the compressor! Thats the least Whirlpool can do after losing so much food and money spent on the wall, and all the water mess etc. I will never buy Whirlpool again, and I will never purchase from Lowes again. We always bought at Lowes, but this was a bad experience, and I get told one thing on the phone with reps and another by A&E.

I purchased the Stainless Steel, side by side with water and ice dispenser, model #WRS325FDAM04 on 11/30/16, paying over $1,600 for the refrigerator. We had trouble from the beginning with the freezer door not closing all the way. When the repairman came out, he said the entire door had to be replaced, as it was warped. Since then, one by one other items are breaking in the freezer and refrigerator. The plastic casings holding the glass shelves have broken on all three shelves in the refrigerator, the wall of the refrigerator and the freezer is cracked in several places, the ice bin has a hole in the bottom, where the device rotating the ice out broke and now when used, ice falls into the freezer, and the bins in the refrigerator have broken as well as some of the door shelves in the refrigerator and freezer.I called Whirlpool before posting a review to provide them an opportunity to at least offer to help in some way. Their response was due to so many pieces missing/damaged they would not be able to help in any way at this time. I purchased a Whirlpool product as I expected I was purchasing a quality product with quality workmanship from a reputable company. I have been sadly disappointed and will no longer support Whirlpool by purchasing any item manufactured by them and will share my experience at every opportunity.

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

I have fought with this issue hundreds of times over the last 3 years. My old water heater work fine until it started leaking, I bought a Whirlpool 40 gal gas hot water heater from Lowes. Worked fine for the first month, then this pilot light issue started popping up intermittently. Now the damn thing doesnt want to light at all. I WOULD NEVER BUY ANOTHER WHIRLPOOL PRODUCT THE REST OF MY LIFE, and I will tell everyone I know that WHIRLPOOL Products are not quality products. DO NOT BUY. There have been so many class action lawsuits about this product and Whirlpool keeps on selling this junk. Im so frustrated with WHIRLPOOL customer support I cant think straight. To reduce your headaches in life, do not buy Whirlpool products as they are junk and their customer support is terrible also.

My 3 door fridge is roomy, well lighted and well organized. I love the fact that when I open the doors, I can see everything at a glance. The freezer section is also well organized and holds plenty. Being able to get filtered water and ice in the door is convenient. The main reason I picked Whirlpool is that it is made in the USA! I want to support American manufacturers that employ my fellow citizens.

I purchased a Whirlpool Side by Side Stainless Refrigerator with Water and Ice Dispenser Model #GSF26CYEXY03 and Serial #HR22908384 for $1397 in October 2012 from Orvilles Home Appliance (GREAT COMPANY!!!). It had problems from day one. The handle wouldnt even attach on the one door so Orvilles graciously went back to their main store and took a handle off their display and put it on ours until the new one was delivered. Then there was a $100 rebate on the fridge. Unfortunately, we misplaced the paperwork and sent the rebate in a little late. We apologized for the delay. The end result was a declined rebate. That was one of the reasons that we chose this particular model in the first place.Next, both of our doors rusted. After Orvilles contacted Whirlpool and went back and forth with them, Whirlpool decided to replace both doors. So Orvilles came back to our house and changed them. The guys were baffled about the rust. Thank goodness that it was still under warranty for that. Next problem was the ice dispenser. It makes ice perfectly but dispensing it is another thing. For the last year we have had to take the ice bin out and empty it and start from square one over a dozen times. I contacted Whirlpool just the other day and was told Sorry. Its out of warranty! We can arrange for you to have the Repair + 1 for a total charge of $356 and then you will have a 1 year operational warranty with that. My thought was REALLY!!! While I was on the phone I mentioned the next problem with it.This problem is with all 3 storage drawers. The fronts of all of them have broken off and now I had to tape them. They all broke within a matter of a few months apart. When I talked to the girl from Whirlpool, I told her that I looked them up and the drawers cost about $54 each. Her answer was I know and I am sorry maam. Unfortunately there isnt anything we can do. Thats why I choose my appliances very carefully! I was shocked to hear that. Just to sum everything up... I am so glad that I spent $1400 to have so many problems and then was given the opportunity (which I declined) to spend another $356 to repair an appliance with icemaker problems and then be expected to spend another $150 to replace plastic drawers. This company is absolutely terrible!

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

We purchased a mid-grade Whirlpool Gold Series dishwasher a little over 2 years ago. 14 months in, the motor failed, requiring a $295.00 repair/replacement. That was nine months ago, and now the motor has failed again. That is outrageous! No more expensive repairs on this piece of junk. Its going to the scrap heap. We just ordered a Frigidaire. While I have no experience with that brand, it cant possibly be as bad as Whirlpool.

My KitchenAid side by side refrigerator/freezer is a beautiful thing, shiny steel surface, gleaming white inside. However, its made poorly. The ice cube maker compartment broke and the replacement came without any installation instructions. It was hard to figure out and I broke it. Now, everything in the refrigerator is freezing and changing the temperature on the digital panel makes no difference. McKinneys appliance, where I bought it, no longer has a refrigeration technician and they referred me to Whirlpools 1-800 number where I supplied some information and sat in my chair on hold listening to music for a half hour before hanging up.The recording on the phone suggested their online chat where I was asked the same sorts of questions and was told I would get the answers I wanted by paying $5.00. I had no idea what I was getting into but I didnt pay, just terminated that inquiry. Feeling cheated by the company whose product I had mistakenly purchased. Im now running the risk of a technician visit, sometime between 8 am and 4 pm a couple of days from now. I have to be prepared to wait around all day for somebody to look at my refrigerator, charge me a lot of money and, from what Ive read online, potentially see the problem return in a very short space of time.

I purchased a Whirlpool hot water heater 2010 and it started having problems 2014. I called customer service. They informed me my 6 year warranty was only for parts and I had to pay for a certified repairman to come and do diagnostic tests and they will pay for parts only. I said the repairman is half the price as the hot water heater and then he has to come install it. Woman on the phone was just as ready to get off the phone as I was! Save yourself and just buy a new one NOT WHIRLPOOL!!!!!!

I purchased a Whirlpool High Efficiency washer and dryer (Model WED4900XWO) from Lowes in March 2013. This washer has performed miserably. I dread each day when I have to use it. The groaning sound is annoying. My husband and I try to leave the house when the washer is being used. We have tried all cycles and combinations of cleaning detergents to get clothes to come out clean. On a regular basis white clothes will come out with spots or discolored to the point the clothes have to be thrown in trash. This is the worst washing machine I have ever used. I will never buy another Whirlpool product.

Purchased I assumed a brand-new electric hot water heater from Lowes. It worked giving us hot water for 5 months then it quit. We called the number they have located on the side of the water heater and they sent 3 references such as plumbers for us to contact because everything they told us to purchase didnt work... so after their references, plumber came out. Instead of him telling us what was wrong why all of a sudden we stopped getting hot water he didnt return our phone call. As a professional that sucks!!! So WHIRLPOOL CUSTOMER SERVICE says the hot water heater that had been working for 5 months wasnt up to code and wasnt wired right and WE need to pay an electrician to connect it right... thats **. The electrician did it correct the first time. Whirlpool just dont want to accept the fact that their equipment is faulty!!! But thats good because I will NEVER purchase anything WHIRLPOOL makes. I dont care if they start making water. I will just quit The hell with that company!!! WHIRLPOOL SUCKS!!! Heres the serial number 1626103174130 and if I had read the neg reviews before I purchased the hot water heater I wouldnt not have done it!!!

The Whirlpool range #GY398LXPQ00 is four years old. This is the fourth major problem. Oven overheats and will not function. I set it at 350 and the bottom coil and broiler both came on and overheat quickly. This is the third time with same problem. I am going to have enough invested in repairs to buy another range. I shall never purchase another item made by Whirlpool or any of its affiliates. That leaves me with Samsung or Bosch, I think. The people are very curt and offered no help at all so calling them is extremely useless. This range is definitely a lemon. Too bad, there arent avenues to make them replace it. I am angry, disappointed, and disgusted. Are you listening, Whirlpool? Never again. May your company go down the drain.

Note that most of the complaints are about gas water heaters, but the electric water heaters dont seem to be much better. Mine, barely made 4 yrs old and both elements and thermostat went. Had plumbers in for estimates in to repair - much cheaper to install a new one (No...not a Whirlpool!). Very disappointed in the product.

Im on Whirlpool Cabrio washer top number 4. Well over $300.00 each, and washer doesnt work with a broken top. I sent a letter to Whirlpool telling them, NEVER again Whirlpool and my reason is the 4th top in 6 years. I received a form letter back... apologizing for a delay in response and, we hope you enjoy the rest of your day, lol. They dont get my level of dissatisfaction or better just dont care. Never again Whirlpool.If you search Cabrio Washer tops you can see thousands of dissatisfied customers... and still Whirlpool has the arrogance to say, occasionally failures do occur, but we can not explain. Really is your engineering that bad? A high school kid could figure out that the spring is to strong for the plastic housing and over time the plastic cracks. Really Whirlpool? A multi billion dollar company? Never again Whirlpool.

Its very noisy, and there are no blankets to purchase to deaden the noise. The dishes all need to be dried by hand. Some of the dishes come out dirty. I would never purchase another Whirlpool dishwasher.

We purchased a new Whirlpool Cabrio Platinum W10405142B washer and dryer just over 3 years ago. We decided to go back to the top load as we were having so many issues with odor from our front load. We purchased the set at a Sears store in Timmins Ontario and we’re quite confident that we were getting an excellent product. From day 1 we have had issues with having to rewash our clothes. We have lint and white streaks on the clothes as if we were using powdered detergent and they are all tangled. We have always used HE liquid and at one point I switched to soap nuts to get rid of using chemicals. We have now changed to pods and still have issues. When the washer is spinning it is deafening. You can hear it outside for goodness sakes. It sounds like it is about to take off and fly.The cycles are ridiculously long. For a quick cycle the other day and a very small load it took 72 minutes... how is that quick? When the wash is done my clothes are all tangled up and are stretching things out of shape. I am careful what goes in my washer and how large my load is. I know not to wash sheets or towels when I am not home as they will eventually be unbalanced and have Sat all day in the washer only to have another hour of washing when I get home. We are currently doing some work in our home and pulled out the washer. The floor has a rust circle from God knows what. I will attach a picture. The lid not longer closes. I have to hold it down until it locks and it still pops up a wee bit.I do not understand why I am responsible for purchasing a new set when the product I bought should have lasted and not caused damage to my clothes or my flooring. How do we as consumers make the manufacturers responsible for things like this. If nothing else the appliances should be removed from my home by the Company and I should be reimbursed for damages and the cost of a new set. I will continue to look for my receipt as I keep everything and I am unsure what is meant by order #.

In November 2014, I purchased a Whirlpool 22 cu ft side by side refrigerator from my local appliance store. During that short time, there have been 4 instances where the ice clumps together and gets stuck, causing a large amount of ice to dump inside the freezer door. When the door is opened, the ice falls out onto the floor. I usually spend 10 minutes picking up ice and wiping up my kitchen floor. I have had the local store repairman over. He told me that was normal. Two things are seriously wrong with that statement. When I spend 1600.00 for a brand new appliance, I should be able to depend on the fact that it will function in at least a somewhat acceptable manner. Additionally, that statement by the repairman convinced me that he was not really interested in fixing the problem. I really dont think the normal operation of a new appliance is for it to make frequent, large messes for the owner to clean up. This appliance is junk and you would be foolish to purchase it. Spend a bit more money and buy a Samsung or LG. Save yourself the frustration and sense that you have been cheated and deceived by Whirlpool. I will never buy this brand again.

We purchased this washer and dryer new in 2011. Have repaired door to washer twice. New doors total cost $500.00 each time. Now it is cracked yet again and the dryer door has to be adjusted. The temp does not work right. Have to do minimum of 2 cycles for drying. Very unhappy. We may as well buy a new set of another make. Tired of the expensive repairs.

After 1 year, my fridges plastic interior wall/liner started cracking everywhere. One crack is right across the entire back wall; other smaller cracks are on the sides and back. Three fridge shelves literally fell apart: pieces fell off! The glue came undone on the sides of the shelf that hold the glass in. Pieces of the shelf itself were falling out of the fridge. The microwave door has plastic trim around the glass on the door, and it is cracking also. It seems that anything that was made Whirlpool and is plastic is cracking and/or disintegrating. Sears caulked the cracks in the fridge and is replacing the shelves, but nothing is being done about the microwave. Whirlpool said, Too bad. Go to Sears. We may have made the product, but Sears is responsible. And Sears is saying Too bad; weve done all we can.

I bought a Duet front load washer and dryer set in January 2009 from our local Lowes. Spin cycle noise progressively got louder over time to the point we contacted our locally owned service company to check it out in June 2011. Cause is defective shell and spin tub, total repair cost $750. This was about the original cost of the washer! I contacted Whirlpool via e-mail (wait time via their phone is outrageous), they wont do anything. Out of warranty. Up until now, Whirlpool has had a good name with me. Not anymore. I will never buy anything Whirlpool manufactured ever again. (Maytag, Kenmore, maybe more brands.)American companys insensitivity such as this is what gives some of American industry a bad name and drives consumers away to quality foreign brands made in Europe: German, Swiss, Italian, Swedish,etc.Im going to take a hard look at Bosch washers to replace this Whirlpool piece of junk.

Whirlpool fridge still freezes water in the bottom of freezer... after five service attempts. We purchased a five-year warranty and so far, they claim that as long as the warranty is good, they will continue to warranty it. We now have three and a half years left. We have currently owned our refrigerator for just over a year (approx. 18 months). During this time, it has had the same warranty repair issue that has been serviced five times so far. We now have an appointment for a sixth time since RC Willey does not want to fix a lemon the right way. The first three warranty repairs were under the manufacturers warranty. We are now under a warranty (extended) that was purchased from the place we bought the fridge from, RC Willey.I want my money back on the whole deal. I was going to be civilized about it because I thought they were common sense decent place to buy from. I thought they would, through common sense, realize that this unit is a lemon and allow credit towards another fridge. In just the past two years, we have bought from RC Willey over $10,000 worth of flooring, appliances, etc. and thats not counting previous years.

We purchased our Whirlpool french door refrigerator with bottom freezer from Lowes. A few months after purchasing, we noticed a pool of water on the floor, resulting from what looked like a leak coming from the ice maker. After contacting customer service, they sent a repair company to service the fridge. This rep stayed no longer than 5 minutes and barely looked at the appliance. He said my refrigerator was not under warranty, which was **, as I personally registered the refrigerator the day it was. My kitchen floor is ruined as a result. I will NEVER purchase another product from this company again. They seemingly left a faulty product on the market and failed to inform me about the known issue. Then they failed to quickly provide needed repair or replacement in a timely manner. They also refuse to reimburse me for the food loss, which would not have ever occurred had they handled the issue appropriately from the beginning. TERRIBLE company. In addition, since Lowes is aware of the reputation of this company and continue to sell their defective products... I will not be shopping at Lowes anymore! Both this companies should NOT be in business!!!

Purchased a Whirlpool Cabrio washing machine from Sears in August 2010. Last week, while my wife was washing clothes, we smelled smoke and the washing machine stopped working in mid cycle. Called Sears repair and came out Saturday 10/10/2015 to inspect the machine. When the repairman checked the codes he determined there was a problem with the motor. When he lifted the machine up the capacitor fell out in 2 pieces. It had blown apart and the motor had burned up. The estimated repair bill was $480.00. Needless to say we did not repair the machine. We will never buy another Whirlpool product or any other product that they manufacture under a different name.

Purchased the machine in 2008 for $800. I did not have any problems (wash 3-4 loads/week), pleased with the washing until July 2015 when the machine was spinning out of control and the machine moved approx. 1 foot across the floor (thank goodness I did not have it on a pedestal as it may have tipped over). I canceled the run. This was a fine washables load of 5 sweaters placed on a medium spin.Scheduled the Whirlpool authorized service tech to come out and fix. He indicated there is extensive repair required and would cost approx. $1800. And indicated he has seen this failure before and it is due to the plastic parts inside. Also, he has seen these washers last about 5-7 years before replacement. Wow, last washer I had was a Maytag and it lasted 15 years costing 1/3 the price of the Whirlpool Duet. Now perplexed on what to buy, called Whirlpool Customer Experience Center to register my complaint and asked if there were any updates to the product that would avoid this failure. The center indicated there are updates but they are confidential and did not know if this failure was addressed.

Two years ago, we purchased a Whirlpool Cabrio Washing Machine from Sears. All of a sudden, it was making sounds in the spin cycle that sounded like a jet airplane taking off. It was terribly loud. We called repair technician, which cost $90, only to find out that the bearing is gone and its going to cost over $500 to fix it. This is absolutely ridiculous! We expected it to last several years, only to find out that we would have to spend almost as much as the washer originally cost in order to fix it. We paid $700 for this machine, two years ago, and I can say that Ive never been more disappointed with a product in my life. My previous washer lasted thirteen years, not to mention my dryer and stove fifteen years, with minimal repairs. I will never buy another Whirlpool appliance again. I have read some other complaints on this consumer affairs website, as well as other sites, regarding this same washer with the same problem on the bearing and cost to repair. If anything, I think Whirlpool should make good on this product and offer something regarding a recall or payment for repair in some form. As far as Im concerned, I will alert everyone I know about Whirlpool appliances and advise them not to purchase it. Now, I either have to pay over $500 to repair my washer or go buy another one. I do not even want this Whirlpool appliance in my house when I can get a washer for cheaper than the cost to repair it.

I really enjoy the self cleaning option on this unit. It really cleans everything without chemicals and then you just vacuum up the dust. My dislike is the ceramic top though. The top scratches really easily and hard to clean up spills during cooking. Overall I would give this stove a b rating.

I purchased a Whirlpool Cabrio set about 5 1/2 years ago. Almost right away the washer made a horrible banging noise when In use... I had purchased a extended warranty so I had the service man out. He replaced something but the washer never acted right. I just about 2 months ago replaced it with a normal washer costing over half of what the Cabrio cost me... and now just a few days ago the dryer followed suit and died. The repair (out of warranty) was going to cost $150.00 and that was just for the part, I had service people out twice for the dryer since it came home with me also. This set was the biggest waste of money I have sadly wasted in my lifetime, is it just that they make things badly these days or the more crap that a machine has on it the crappier it is???

Purchased a GGE388LXS04 electric range in June of 2013 from Lowes. In September 2013 one of the top burners went out, under warranty Whirlpool repaired the burner. Now after attempting to use the self cleaning mode for the oven, the ovens (top and bottom) along with warmer device do not work at all. This issue is evidently a major issue with Whirlpools electric ovens. Will call Whirlpool tomorrow as the oven is still under warranty, will also call Lowes and see if they will replace the oven with an oven with a comparable brand. Wish I had read this site before we purchased this oven. A very bad experience.

I bought the Whirlpool Cabrio top loader set in 2006. Honeymoon was over after the first year and I had to change the dryer element then the washer with the F51 code six months later. Last year, I had to replace the heating element again! For the last six months, I have been dealing with the dreaded UL on the washer. I cant afford to pay a technician $100 to come out and tell me whats wrong let alone what they will charge to repair a problem that, from the looks of this message board, will never be fixed. I have no choice but to get it fixed in order to sell the ** machine. I paid $1400 for this brand new set and have already invested $500 in repairs. How is this possible? I had a 20-year-old machine prior to this and never had an issue. There are lemon laws for cars, why arent there any for appliances over a certain amount? How in this day and age can a company be allowed to sell such garbage? I will never, ever buy another Whirlpool appliance as long as I live. Any other brand can have my money any day.

I am very upset with this company. I bought my fridge two months ago from Sears. The fridge is leaking water and Im having a lot of problems with the freezer and the ice maker isnt working at all. Ive been trying to reach the company but they always leave me hanging in the phone and never answer and keep hanging up. I am very upset with this company. I wasted a lot of money for nothing. Please people dont buy fridges from Whirlpool and dont waste your money.

I am writing due to the defects and flaws in my recently purchased appliances. I chose Whirlpool believing I was buying the highest quality for longevity purposes. Every appliance I own is Whirlpool or Maytag - same company. I purchased warranties and was told the warranties dont cover my issues and was basically brushed off. I am infuriated. Here is a list of complaints. Refrigerator is cracking on the inside on the inner door and at the bottom. These cracks surfaced within the first year of purchase. The warranty does not cover cracks in the inner body.The oven/range has an exhaust that bellows out of the top of the range in a way that the smoke curls up onto the panel and discolors it. I have never had an oven constructed with an exhaust pipe in the front that pours smoke onto the range itself and into your house. The dishwasher paint has rusted off on the door as have the screws on the inside of the door. The cover panel on the cleaning dispenser of the washer has popped off and cannot be popped back on, hence the guts of the dispenser are always visible and when I go to load the cleansers the front has to pulled out from inside the dispense.The refrigerator is also leaking from the bottom and the ice-maker no longer produces ice. This started off and on for the past 2 years. At first I thought the leak was from a near by window. No it is the refrigerator. All of these appliances were purchased in 2013, 14 and 15. New. I am 56. I have never had issues like this ever in my life growing up or as an adult. Appliances lasted forever. I am one person. How much damage could I do? None.These are flaws in chemical compounding of the paints and materials for cracks and rust. Whirlpool was called various times and was not interested in sending a rep to verify my claims. They said all of my warranties did not cover such issues only motors. Lots of many spent in vain. I will not purchase Whirlpool again as they seem disinterested in customer satisfaction.

I have the Whirlpool washing machine for last 15 years and there has not been any complaint since its acquisition. I do a lot of laundry because I have a big family, but not major issue so far. I will recommend this brand to anyone willing to buy a washing machine.

I purchased whirlpool Model# WFG540H0ES gas with convection. I purchased it because the price was $1000 dollars less than comparable ovens and even now the price has gone up $300 since I purchased it. I really wanted the luxe look at a discount price, a burner that you could lay a grill over, and five burners which it provided all of those things. I hesitated to buy this oven because the door fell off the last Whirlpool within three years and they refused to fix it so I tried not to buy this brand but it had the amenities I wanted for the price I could afford. I really like the oven. I like the oven the best because it really does make a great cake. I like the two large grates that sit across the oven. It makes it feel high end. If you dont wipe the range immediately grease gets stuck on the range and is hard to clean. This is what I like the least. Im ready to wipe on the weekend and its too late. It took me four days of internet comparison to decide on this one. The house is not painted, the cabinets are falling off the wall literally but I am extremely proud of this oven and it makes me feel affluent even though Im not.

Bought this machine June 23, 2016. First use, I called Lowes where I purchased it to say there is something wrong as it makes a grinding noise. I was informed that is normal for agitatorless machines. I asked if he could hear the noise, and he said yes, thats it. So I disconnected thinking, Wow, who makes a machine in todays technology that is so loud you think something or someone is in serious pain?! Now am at the point where I want this design in pain out of my house! Going to Lowes today to try and talk rationally for a complete refund so I can purchase an LG or Samsung which is what I should have done originally.

No get this and the dryer used. Top of the line. I am having fun seeing all the choices. I would recommend because of the efficiency. Measures soap and softener depending on the load size. Like a miracle.

We purchased a Whirlpool refrigerator (WRT5L1SMYF00) in April 2012. Within 2-1/2 months, items were freezing on the shelves of the fridge box. I called Lowes & was told to call Whirlpool. I did as suggested & they sent out their service co. tech, Turner Consumer Services. I had all the same issues as everyone else in these reviews. i.e., food freezing where it shouldnt or spoiling when the stat was turned down even one notch. The staff at Whirlpool was as uncooperative as is possible. They smiled and lied to my face during phone calls - anything to get me off the phone. During the next 4 months (till Nov.), techs came out 5 times, never having the part needed on the truck. Always, it was my fault somehow that my stuff was freezing. Their chosen tech service employees were rude, condescending and without knowledge. Five service calls, 3 parts replaced and numerous calls to Turner & Whirlpool got me nothing but stalling tactics. I, too, was told that their tech had to fail the appliance before they could consider replacement - all lies. The tech, when he gets here, says hes not allowed to fail the unit. On the 11th of Nov., I awoke to totally frozen-up coils which kept the fridge box from cooling. We had company here from out of town. We moved out the new fridge, moved back in our 21-yr-old unit and got through till our visitors left. Whirlpool has been completely unresponsive to my appeals for some relief from this fiasco. I continue to receive requests from Whirlpool to purchase an extended warranty. Really? My husband & I went out to Sears and purchased a GE & have had no issues with it whatsoever. We are older, on a fixed income, and can ill afford to purchase 2 fridges in 7 months, not that Whirlpool cares. Not only will I never buy another Whirlpool product, but I will warn everyone possible to not buy from them. In fact, my intention is to use every possible forum, Facebook, Twitter, any & all review sites here in KC, MO or anywhere to put Whirlpool down. I am, however, considering one more expense - a lawyer.

I purchased a compact frontload washer. At first, I was getting a code f30, which took the technician weeks of coming to my home and changing different parts to finally accomplish that problem. After that, the machine would not go into high spin to wring the clothes out. So everything comes out soaking wet. After two different companies (Herbs Appliance and DanMarc Appliance which I got from my service contract) changed speed control, board, latch control, main computer, and top control board, the machine finally worked for a little while. Not long after, the machine is no longer wringing out once again. I am no longer under contract but had a repairman out three times to inform me this machine is a lemon. Whirlpool tells me I am no longer under contract, but my argument is this is not a new problem but a preexisting one.

For the second time in 18 months, I have had to replace the top shelves on my refrigerator (Model #ED5VHEXVB01) because the cheap plastic borders have broken. The first time it was covered by the 1 year warranty, but this time (12/11) Ill have to pay $130 just for one shelf. Unless the quality of the product has improved, Ill probably expect to have to replace them again within the year. Needless to say, Ill never buy Whirlpool products again. Im out $130 because Whirlpool will not replace them for free because the product is no longer under warranty.

I bought this machine in September of 2014. Six months later I HATE IT!! It does NOT get the clothes clean and dont even try to bleach white towels or socks, it doesnt pump the correct amount of hot water and things come out just as dirty as when they went in. It tangles everything together and frequently stops working because it unbalances the load with its lack of water. Ive always been proud of how my familys laundry looked and now Im just embarrassed. Im considering donating this to a human society for dog towels. Stay away from this washer, its horrible. Im going to the laundromat and shopping for a new machine ASAP!

Cabrio Washer and dryer are about 3 years old. With washer a residue is left on clothes and require an extra rinse, sometimes 2. Also, clothes become unbalanced and I have to rearrange clothes, sometimes more than once. Washer doesnt go through rinse cycle on own, I have to manually make it rinse and spin. Both washer and dryer have rust on the tops and the writing is fading.

Good Morning. We recently built a home with Pule in Nexton, which is located in Summerville, SC. The appliances we chose came with the dishwasher, stove and microwave. Everything other than the dishwasher has been doing great, but as for the dishwasher I am extremely upset...we are newly weds and received two nice sets of glass and at least 12 of them have been broken in the dishwasher. Please advice.

Purchased a Whirlpool washer/dryer pair @ least 5 years ago. Great machines. Washer washes very clean. My only beef is that once the cycle starts I cannot open the lid. Dryer will dry almost anything in 10 minutes or less.

The Whirlpool I purchased has been the worst ever! Nothing comes clean even when I hand wash everything first and never has even from the beginning. I will never purchase a Whirlpool again. Now the machine wont drain I have gone through all the recommended steps for cleaning. The Whirlpool stove is almost as bad!

We purchased our Duet in July 2010. It worked great until two weeks ago when the washer sounded like a 40-year-old washer. The bearing sounds like an extremely high-pitched “wrr”. We can hear it in the back of the house. I looked online to get parts and noticed that you cannot replace the bearing. You must replace the entire rear drum ($358.00). This does not include the labor. I talked with a technician, and they said the whole drum must be removed, not a one-man job, and to take the whole thing apart. Now, theres no price for installation. Lets go low ($200.00). Probably more. I cannot get a price nailed down without a visit. Now add those together ($558.00), I could put almost $600.00 into a washer that this could happen to in another 2 years. Wow.We had a washer that lasted us 15 years without any parts. Is there anything that you can do to help me? This is totally outrageous. Please help. Thank you. This was part of my chat to Whirlpool. Whirlpools response was I understand your problem but cannot help you. It is out of warranty. No help, no discount, nothing. I will and have all my friends never to purchase Whirlpool. This is from a so-called American company. Im very disappointed.

It is my belief that through my experience that most Gas Range manufacturers mainly Whirlpool corporation purposely designs the stove igniter part to fail in 5-10 years. They do this in hope the consumer will purchase a new stove. The igniter in my stove has failed 6 times since I purchased it in 2005. I have had to replace it at my expense each time. The last time it failed, I asked Whirlpool if they would do a good faith gesture and replace it. They very rudely refused. I will never purchase another Whirlpool appliance again and encourage others to follow me. If they give me this much grief over a simple good faith gesture, I can only imagine the difficulties in getting them to honor a warranty claim!

We bought our Whirlpool Cabrio Platinum top-loading high efficiency machine Model #WTW8000BWG in Feb. 2015. It cleans well, and is easy to select water temp, spin speed, etc. It's simple to load, but because I am short, I have difficulty reaching stuff at the bottom of the tub. A stool is needed. LOL. In the 5 years that I have owned it, I have not needed any kind of service to be done on it. Very reliable. I have had Whirlpool washers and dryers before and my success with them is why I purchased the set I have now. And so far, so good. Highly recommend.

I have been married for 43 years and started my marriage with a Kenmore Washer and Dryer. That was because my mother, aunt, and grandmother all had Kenmore Washers and Dryers. Kenmore was made by Whirlpool. In 43 years I have gone through two sets of Kenmore Washers and Dryers, and one set of Whirlpool Washer and Dryer. I have always been very pleased with your product and have never considered buying anything else. However, last year we bought a new Whirlpool washer and dryer. I have no complaints about the dryer, but this washer is a piece of **! It is a cabrio top-loading high efficiency low-water washer. What idiot came up with this idea? Tonight I am once again having to divide my washer load and run them for at least a second time. This is not cost effective!!! This sprinkling with water and sucking it out doesnt work. Not to mention that since we have gotten these wonderful energy saving appliances our electric bill has increased instead of decreasing. You need to make a washing machine with a wash tub and agitator like you use too.

I purchased a Whirlpool Cabrio Set from a local store. Just over a year later, the washer got very loud like a jet engine. Called the registered repairman, he came out took a look and said he would get back to me. Called him 3 times over 3 weeks, no show (Hoodland Appliance). Called someone else, repaired it for $400.00. Called Whirlpool, they are not interested. 2 years later now and the machine is getting loud again. This is due to the spin throws water up and it is able to get out of the tub and down into the barring and the soap residue wears the barring out. Bad design. Called Whirlpool again and again they are not interested but can put me in touch with a repairman. I will not repair again but will use until dies and buy something else not related to Whirlpool. So much for energy efficiency.

I purchased a washing machine FS65 on 10-30-2005. In Oct. 2009, my washing machine developed some fault so I contacted the Whirlpool service center and got it repaired. Again in Dec. 2010, the appliance became faulty and so I contacted the service engineer to attend to the machine. He repaired it and I paid 2500/-. But the very next day, my appliance showed the faults again. It was rectified with replacement of PCB and I was charged 2786/- on 01-20-2011. Again on 09-04-2011, the machine became defective. On the call to service center on 09-05-2011 and attended by engineer on 09-06-2011, I was informed that PCB is defective. I failed to understand that the PCB replaced in January was of what quality that it has to be replaced now after such a short span of time. I feel that this is clear cheating with me.

I havent had my Whirlpool Cabrio washer for even 5 years and I have had to replace the glass lid and now the tub bearings need to be replaced... I have read countless complaints for the same issue. I feel like Whirlpool should at least send out free replacement bearings and the $85.00 bearing press tool that you will need if youre handy enough to fix the problem yourself. PS to all of the poor victims of Whirlpool bearings, go to Amazon and you can buy the bearings and the tool for about $150.00. You will need to order bearings part #10435302 and the bearing driver tool #w10447783... And as far as my matching dryer - knock on wood - it still runs great.

My old GE was better. I have to clean my Whirlpools filter once a month due to hard water - was wondering why my plastic cups had a white film - that was why. I have to put the knives and forks with the points facing up. My old dishwasher I could put the silverware in any way I wanted in the silverware compartment. My old one was quiet/my whirlpool I can hear it from the bedroom????

Remodeling kitchen. On Sept. 2017, bought new Whirlpool microwave mod# WMH5352OCS, Actually put to use on Jan. 2017, by Nov. 2017 started getting open door errors by late Dec, 2017 completely quit working. From what I have been reading they barely make it thru the warranty period. Maybe they will run longer if one doesnt register the appliance. Especially with the crappy service for the ones that tried to have it repaired under warranty. I purchased it at Costco online, my next complaint will be to Costco, hopefully theyve gotten more complaints and pressure Whirlpool to stand by their product, NO MORE WHIRLPOOL FOR ME EITHER.

I bought a frost-free deep freezer 2 years ago from a box store. Within 1 year it went out and I lost approximately $1000 worth of food. Called the box store and they called A&E. Bought the extended warranty. A year later the deep freezer went out again. Lost another $1000 worth of food. Im scared to death to use my Whirlpool deep freezer again. Am I going to lose $1000 worth of food each year? No satisfaction with Whirlpool whatsoever for this piece of junk. And the problems were manufacturer defects. In fact, one of the parts had a recall on it and we were never notified. I dont know about anyone else, but I cant afford to just throw away $1000 worth of food every year. Ive bought my last Whirlpool appliance now. I wish I had read these reviews. It would have made a difference to me.

Whirlpool oven aqua lift - This oven is the worst in the world. I cant even imagine cooking a turkey in it. After cooking a pizza it took four cleanings and a lot of scrubbing. Self cleaning --- not, you clean and clean and clean. I have had ovens that were not self cleaning and easier to clean than this. Do not buy. And Lowes is no help at all. Run as fast as you can.

I bought new hot water heater. I installed it did and it did not work. I called them, and they sent a new part. A service man installed it, and it still did not work - he was unable to get it working. They said my gas supply line 1/2 od was too small. I had it replaced to 5/8 od 1/2id, and it still did not work. I called them again. They offered to send more parts and try again. This is a brand new water heater, never fired. I asked if they would give me a ra number so I could return it to the store. He would not give it to me. He insisted he send some one out to try to repair it. Meanwhile I have had no hot water for 2 days. He told me do what I have to do and hung up on me. So I removed the heater and took it back to Lowes, where they were glad to give my money back. But still, I lost a day of work and paid the gas yo bring it back. I went to home depot bought a GE hot water heater. I had it installed in about 15 minutes and it is working fine.

My NEW Whirlpool top loader just stopped working. I bought it in June 2015. The extended warranty I purchased ended at the end of June of this year. Guess what happened a few weeks later? The thing died. Seems totally fishy! My parents washing machine lasted 20 years. Why does this one die weeks after the warranty expired?

DO NOT buy Whirlpool branded electric ovens. Whirlpool put out an update and it fried the control board of our electric built in oven. They refuse to fix it. They have kept us on hold for two hours and then tell us there is nothing they can do to fix it. We had an extended warranty that just “disappeared from their system.” They told us someone would call back us but no one has. This was an update we were told we had to run in order to use the associated APP. Our oven is only 2-years old. We now will need to pay for the repair ourselves. DO NOT BUY.

We have an 8-year-old built-in Whirlpool Estate. It is probably as basic a model as you can get. It has been 100% reliable, and cleans the dishes well, even without rinsing. We do not buy expensive premium dishwasher detergents, either. So far, we have required no repairs. Basic features--heavy wash, normal wash, pots and pans. This dishwasher is standard (not extra large.) This is not a fancy dishwasher--just white. It is what matches the rest of the appliances. We have been lucky regarding the performance of such an inexpensive dishwasher. We paid about $250 for it.

I had the first microwave for 6 years. My husband messed it up so got a new one, same over the stove type. It has lots of programs. Its a rather large microwave, plus it has a steamer which cooks vegetables with steam while I am doing the rest of the meal and whats more important is its quiet. The site is fantastic not just in width but in depth. The best thing about this microwave too is that it has a frozen cycle which does not partially cook the food like most microwaves and the defrost is the same, it does not partially cook it actually defrosts completely without cooking it. This is by far the best microwave I have ever had, and I wouldnt want any other brand. It might cost a little more than the usual brands but its worth it. I also have a mini Whirlpool on my Countertop for my grandchild to use so he keeps away from stovetop at all times.

Thermocouple failure on a Whirlpool water heater - We are having trouble finding the part to replace it because the thermocouple is threaded left-handed, and Lowes does not seem to have any replacements in stock locally. Meanwhile my tenants are without hot water, and my repair bill is escalating due to labor.

Had washer less than 1 year and washer stopped and was flashing code F 51. Called Whirlpool and they sent a repair person. He worked on it and didnt fix problem. Called Whirlpool back. They had to order parts. Repairman came back - replaced parts. Now not 6 months later same thing happening. Whirlpool said we have to pay for labor to repair again. We went online after this happened the first time and saw where others had same problem - this washer should be recalled. The repairman said this part was corroding. This should not be happening on a new washer. We will never buy another Whirlpool product again!!!! Im concerned that it will keep repeating over and over and we paid 700+ for this washer not 1 1/2 ago. My last washer lasted 15 years!!! Wasnt a Whirlpool!!!

I bake a lot so my husband bought me a new gas range for our 54th anniversary. After the first few times I used the oven, I decided to clean it. I noticed then that there were some burnt grease spots and streaks between the oven glass door. After 2 years of use, it has gotten much worse so I decided to take the door apart to try to clean the glass in between the layers of glass but there are three instead of two. I cleaned the inside of the outer glass, but that didnt take care of the problem. Most of the stains are between the other two panes of glass. That, I cant get to. I feel that this is poor design and not sealed properly. I take good care of everything I own and I expected this range to last me the rest of my life but it is put together with cheap plastic parts that wont last long. It is the first new range that I ever owned and paid a lot more for it than any Ive had. I expected better.

It works great, it looks great. I been having for many years, and never gave me any problems. I do love nice microwaves and Whirlpool is a great. I would recommend it to anyone that is interested.

I bought a Whirlpool Partner II 5 and a half years ago. It was always noisy and took very long to run a cycle. It started to malfunction after 2 years. We bought a new computer for it and a new control panel for the touch keys. It still kept not running a cycle fully. We found a YOUTUBE video that showed how to reset the model by pressing a combination of Normal and Heated Dry and that seemed to fix it for 2 years.It has stopped working again. Now it seems that the heating element is out. It doesnt clean at all, a scum film has covered the inside of the dishwasher and even mold spots are appearing. Ive had to wait extremely long times on hold to talk with an agent. My option is to hire a repair tech to come out and repair it and I pay for the parts. Seems like a bad deal since Ive already spent over a hundred on repairing it and a lot of hours. I will never buy a Whirlpool brand appliance again.

Cabrio washer bought 5 or 6 years ago. Started a whining noise when spinning, so loud we close the washroom door to hear the TV. Called service, they immediately knew that the main bearing was going out & quoted the two parts needed to fix THAT COSTS MORE THAN THE MACHINE DID NEW! Labor was not included. Was also told that it will eventually start leaking. Piece of junk. What happened to simple washers that did a good job washing in half the time that lasted 15 to 20 years???

I have had my washer & dryer about 12 yrs. It has given me great service; however the spin mechanism on the washer stopped one month ago. It was replaced thru my home appliance warranty. I need the front loader style because Im disabled now, and cant take clothes out of washer. My previous set was Kenmore & it lasted 20 years. Looking to purchase in 2 months.

Bought a Whirlpool 25 cu ft side by side in 2011 and now just 4 years later the compressor is bad. Called them and they only have a 1 year warranty, which is nothing for a compressor. They told me for $350 they could replace it and it be good for only a year. Not going to sink more money into a product even the company has no confidence in. The repairman advised to stay away from Whirlpool as they were not the company they used to be. Also the salesman at Lowes where it came from said they used to have a 5 year warranty but changed several years ago and the quality also went down. We have had refrigerators last 25 to 30 years in the past but no more thanks to modern technology. Thanks a lot. STAY AWAY FROM WHIRLPOOL!

I purchased a washing centre at Canadian Appliance Source. I paid to have it delivered, installed and for them to take away my old appliances. I had several issues and when I called the store, they sent me to Whirlpool warranty who dispatched a repair technician a few days later. With nothing solved to my satisfaction, I called Whirlpool again. I spoke to a customer service rep who gave these responses, she put me through to a manager who gave me the same responses. When I asked to speak with someone above her, she said she could put me through to another person at her level but noone at a higher level.I want to hear the same response again? Really? Her only other answer was to email the Whirlpool Executive, which will be my next step. This is a summary only of my experience of the first few days after the purchase.Problem: The first load I washed was 1 set of blue sheets with 2 pillow cases. The water didnt seem to cover the load but I thought when it started to wash, they would get wet. When I took the sheets out of the washer, there were several dry spots and some kind of residue on several areas, so not washed or cleaned as expected. I tried washing one sheet, same thing. Tech solution: Put in some wet items to the load so the washer thinks the load is heavier and will add more water, or add a bucket of water to the load, Really? Whirlpool response: The washer is working as expected. Really? Problem: I did a warm water wash, expecting the machine to dispense a mix of hot and cold AT THE SAME TIME making it warm water. The washer starts with cold water then stops and puts in hot water. I dont want cold water or hot water on this load I want warm as recommended by the manufacturer! Tech solution:Dont use warm water wash. Really? Whirlpool response: Works as expected. Really?Problem: Dryer is way too hot on the delicate cycle, not good for delicates! Tech solution: Use the air dry cycle. Really? Whirlpool response: Dryer is working as expected. Really?Problems I didnt even discuss: The load is really really wrinkled when it comes out of the washer. Who wants to have to go back to ironing everything they own? The washer tub and dryer are really really small! I should have read more reviews and headed the warnings! Comments: I purchased online, biggest mistake. The store will not take it back. Whirlpool will not take it back. Hindsight is 2020! If I could have given negative stars, I would have.

I love my Whirlpool. Were a family of 3 with a pet dog. Its handle one childs work uniforms and the others sports uniforms (yuck). And then theres my work/weekend clothes. Its very reliable and it gets the job done. We have no complaints.

Less than 2 years after we purchased our whirlpool dishwasher, the rack started to rust. Now the tines are so soft they fall off. The last time we bought a dishwasher the Same thing happened, but after 15 years! They dont even have an option for that to be under warranty so it tells me they dont stand by their product. I will never buy whirlpool again.

I have had my whirlpool oven for approximately 6 years. This will be the 3rd time I have had to replace the thermal fuse. For the last three times I have used the auto clean, it blows out the fuse. It has cost me $110.00 each time I called my appliance tech to replace the fuse.

I bought a Whirlpool top load washer. In less than a month it had to be serviced by their recommended service repair. It has never worked properly. It malfunctions almost everytime it is used and takes at least an hour to wash even a small load. At first I thought I may have acquired an odd lemon. After talking with several friends who had bought the same Whirlpool model I found we all had the same complaints. My old machine could wash a king size comforter in 36 minutes... that was energy efficient.

Refrigerator stopped cooling... Paid $200 to have it diagnosed... Cost more than a new refrigerator to get fixed...$14,000. Refrigerator was 7 years old, energy star. How can it be energy efficient if it was made to last only seven years? How much energy is wasted making new ones to replace the broken ones, that cost too much to fix. Energy star. What a scam.

Extremely unsatisfied with their customer care. I purchased a washer and dryer 18 months ago and did not choose to purchase an extended warranty. I currently need a main control board replaced after the machine stopped spinning and draining. I hired a wonderful handyman, who originally suspected the lid--locking mechanism was the problem. When that was replaced and the machine still wasnt functioning, he determined the main control board needed replacing. This is a manufacturer defect and costs approximately $300 for the part, not including labor. Of course, my machine is no longer covered under the extremely limited manufacturers warranty that only lasts for 12 months, so I am stuck picking up the bill. Once done with all the parts and labor, its cheaper to buy a new washing machine especially because they still wont add a warranty to it after its fixed. I think its absurd that a manufacturers defect isnt continually covered under warranty no matter how old the machine is. Customer service continued to tell me I should have wasted more money on a company that doesnt care about customer satisfaction and purchased an extended warranty originally. Horrible investment! Will never purchase Whirlpool appliances ever again!

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

I bought it a year ago and the warranty is not even up and only in about a month the freezer door handle keeps falling off then the stainless steel which probably is fake is rusting too. They replace the handle and the door and the handle still keeps falling off and the doors are rusting again. My GE stainless steel dishwasher and stove are five years old and there is no rust on them. Whirlpool says it is cosmetic and that its not covered under the year warranty. I will never buy Whirlpool again. Awful customer service!

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

I purchased the Whirlpool Cabrio Top Load Washer in 2009. It stopped working and I found that it needs a new control panel and recirculating pump which will cost $390, including labor (plus the cost of the service call to diagnose the problem). I would not have expected to have this type of problem with a washer within 3 years of purchase. I cannot recommend this machine.

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

We ordered the Whirlpool 6.4 CuFt Electric Slide-in Range WEE745HOFS from Costco on 1/3/2017. It was delivered 2 weeks later. The FIRST time we turned on the oven the top heating element caught fire during the preheat and damaged the interior of the oven! The interior paint was completely burned off above the fire, exposing the raw metal. Costco called Whirlpool for us to ask for a replacement oven. Whirlpool refused. We called too. Whirlpool sent out a repairman who replaced the element and PAINTED the damage on the top of the interior.For weeks, every time we turned on the oven, the house filled with smokey paint fumes. I have a chronic lung disease (sarcoidosis) so the paint fumes were a serious problem. We stopped using the oven. Weve hardly used the oven since that time because we have a nice, large countertop oven. I turned on the Whirlpool oven again in January of 2018. The top element burned out AGAIN after less than a dozen uses! I was 2-3 days past the purchase date and again Costco tried to advocate for us but Whirlpool refused to help in any way.My next door neighbor purchased this exact oven two months before we did and she has had the SAME problems (and worse!) with NO help from Whirlpool! I have HATED this oven even though we mostly use the cooktop. A $1300 oven should NOT burn up an element in less than a dozen uses! The cooktop is very difficult to clean, scratches and stains easily. The trim and panel also scratch very easily. Yes, I did purchase the Whirlpool cleaning kit and follow all directions carefully. My next door neighbor says dont bother trying the Whirlpool Aqualift cleaning feature because it DOESNT WORK! She hates this oven too. By the way, ALL of my appliances are new Whirlpool appliances! So far the dishwasher is doing ok but the microwave is 4 months old and the door is not closing completely, so it has to be adjusted often or it clicks rather than cooking. VERY DISAPPOINTED IN WHIRLPOOL!

Last week dishwasher leaked. Set up repair with our local gas company that has service plus. Came today. Repairman showed me there is a hole in the bottom of the tub. Upon closer inspection it looks like the manufacturer drilled a hole that wasnt needed so they routed out a depression in the tub and must have put in some sort of plug or filler of some kind which now came out. I called Whirlpool and explained to lady about the defective tub. She said well if it had a plug of some sort put into the tub it would have fallen out before this. I said Well it didnt it just must have happened as it never leaked before. She said it is no longer in warranty. I told her this is a defect to me as if you drill a hole in the tub that wasnt necessary and then the plug failed that you put in to hide the extra hole. It is a defect not a warranty issue. Upshot is she wouldnt do anything about it. I told her I have always bought Whirlpool but if this is their policy its the last time I buy anything made by Whirlpool. After reading all the complaints registered here about Whirlpool I guess I am more than fortunate as my dishwasher (bought in 2006) had run great until their plug fell out (Great except for all the rinse aid that has leaked out for several years.).

This is the loudest washing machine I have ever had. Sounds like it is grinding. Called Whirlpool and said that is normal. Will never buy another one and will let everyone I know how noisy it is and not buy one.

Purchased Whirlpool Microwave 1.6. The design has 5 BIG flaws. 1. Too large in depth, cabinets on each side cant open. 2. The one light under unit is so far to the back wall, you need a flashlight to cook spaghetti or use stove. 3. Too large in height, cant get a big pan on your stove. 4. Top of unit is open so much, if you spilled something from the cabinet above it would go right inside the works. 5. Instructions are hard to read & figure out, the wall hanging support is just one piece and if you dont have 2 main beams youre out of luck. GO buy a GE, put it up in 1/2 time & good & secure and works great. Has 2 lights on each side under unit. Fingers over the holes at the top. 1 inch shorter, 1 inch thinner. To my surprise the turntable is even larger, go figure.

I purchased a Whirlpool washing machine from PC Richards in Lake Grove 15 months ago. I paid $590.00. I had to call PC Richards back because it sounded like the machine was not spinning right. The servicemen came back and said nothing was wrong. It was supposed to sound like that. Now the machine stopped draining and spinning. I went to the store and they handed me customer service numbers and said they could not help me. I contacted Whirlpool online and received a phone call from a woman that gave me a lesson on how to load the machine and put soap in it! She was a very polite woman, but, gee, that didn’t solve my problem.After 4 days I was able to get through by phone and was told to call service. I contacted Mahler Appliance. He looked at it and said he couldn’t fix it and took a check for $81.47. He told me to call Whirlpool. I called Whirlpool again and got their service people. The gentleman came and could not figure out what was wrong. He tried a few things and said it was probably the main board. He said to call Whirlpool, but they most likely won’t give me back my money. He could charge me $460.00 for a new board per his supervisor. I just paid $590.00 for the machine and another $87.00 to some guy who took advantage. He left with an $87.00 check and I still have a broken washer. He did tighten up a loose wire he said he found and told me to try it and good luck. So I tried it. I put clothes in and turned it on.I came back about 20 minutes later to see if it continued to run and I slipped and fell on the ceramic floor because water drained out from somewhere and went all over my floor. I have injured my back and elbow from hitting the hard floor. I also have water all over the place and finally a very broken defective washer. I am angry. I hurt myself and have spent close to $1000.00 and I still have no working washer and no way to buy another one. The washer is 15 months old. That’s brand new to me. There was obviously a problem from the beginning. Whirlpool has always had a quality name for years. I would hope that they would stand by their product and fix my washer for me. It is obviously defective.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

My new washer is very inefficient. Clothes do not come clean and come out very wet. The cold water only rinse is not an environmental feature... clothes come out so wrinkled that instead of hanging them to dry as I used to (after shaking out the few wrinkles from a warm water rinse in the old washer) I now have use the dryer. This makes no sense to me... I wish I had spent half of the price of this new washer and had the old one repaired... at least then my clothes would come out clean.

My two year old Whirlpool refrigerator died. The compressor went bad. $859 to replace it. I only paid $999 for the fridge. This was crazy. Two years old. Heard it was not uncommon and the technician said most refrigerators warranty the compressor for up to 5 years but not Whirlpool. Had to go buy a new refrigerator.

Rust started forming early on our washer and spread quickly. Our house is air conditioned and not near the ocean. There was no reason for the rust. Poor quality finishing is the only explanation. When I called to complain I got nowhere. I wish I could show a photo on this website. It would dissuade anyone from ever buying a whirlpool.

Bought a new set of Whirlpool Cabrio Platinum tin replace my Maytag that had finally died. I believe this is the worst set Ive ever owned. It wasnt inexpensive but its cheaply built. Cant wash a set of sheets without it getting out of balance, even if you carefully place them in the washer as they recommend. They knock up no matter what you do. The dryer is gas and my clothes still have to be turned back on for more time that should take. We are talking about over an hour. Ive had them just a few months but Ive had it. I want my washer and dryer to just do their jobs like you expect. Im selling them or donating them but whichever they are out of here. Whirlpool, I am ashamed of you. Putting out such a poorly made washer and dryer. Instead of the name Platinum. They should be named Salvage. Never again Whirlpool. Never Again!!!

I have a Cabrio washing machine that is just barely two years old. I have already spent over $500 on repairs/service calls. The first repair was the drum which cost $300 + to repair. Typically, my experience with washing machines is I buy a new one after years of service simply because I want a more updated model. I just bought a different brand to replace the Cabrio as it has another broken hinge (one rusted out. How bizarre is that?) And it wont work on some of the choices for cycles. The first time I called whirlpool, they were totally unresponsive and told me there was not any problems with the machine even though the part I needed was on backorder for three weeks. I have never been so frustrated with a product I thought was a reliable brand, not!

If you ever bought something from the store and the sales person said dont worry about, if you have any problems they will go ahead and fix it.... BEWARE... I purchased my fridge from BrandsMart USA in Feb of this year.... It was approx 2500.000 fridge we bought because it matched the rest of the appliances. Little did we know this has been a living nightmare. They have been out to the house 7 times to fix this thing. Its less than 8 months old.... and its still broken. I have been without a fridge going on 2 1/2 weeks. The Senior Customer product review supervisor said he would get me a new fridge that was on the 27th. Every time I call him, his voice mail is full of.... Only to assume that is full of other satisfied customers. I HOPE YOU WILL NEVER HAVE TO GO THROUGH THE PROBLEMS I HAVE HAD. What a waste of $2500.00.

Just bought what I thought was going to be a great dishwasher. It had all the features I wanted. But, I discovered that none of my silverware would fit in the slots provided in the silverware basket. It is a disaster. The slots are so tiny that most of them are unusable. I called Whirlpool thinking that surely there was another basket I could substitute, but no, there isnt. Everyone was very polite, but the end result is that the Ill be handwashing most of our silverware. Unless your silverware has very narrow handles, forget this machine. Obviously designed by someone who has never loaded a dishwasher!

I purchased a Whirpool fridge five years ago. To date it has had 7 repairs. The latest round has lasted over five weeks and the expensive warranty I also bought is about to run out. The repair man is on his third repair and I havent had refrigeration for five weeks. In the meantime they wont replace the fridge, and it takes two weeks between scheduled visits by the authorized repair man.

I bought Whirlpool water heater model #FG1H5040T3NOV about 5 years ago. Burner assembly was replaced two years ago and now, thermocouple was replaced yesterday.

I purchased the Whirlpool Cabrio set about 5 years ago. My problem is that the washing machine has NEVER gotten our clothes clean. The dryer is fine but the washing machine is useless. Clothes come out of the machine in the same state that they went in even if I use stain remover. Dont buy this machine!!

We too have nothing but problems with our supposedly top of the line convection/microwave oven. Purchased in 2010 in February for new kitchen. From start, original microwave installed did not work, would not cook or heat. Dealer replaced. One year later, same problem, but now out of warranty. Had to pay labor, costs, and parts to get fixed. Fast forward 13 months, again magnetron needs replaced, microwave will not work. What a hunk of junk for our money. I will never buy any Whirlpool appliances again, and I will tell everyone I know the same. When you call customer service, they are nice but only say “too bad, out of warranty”. What a joke for a major appliance company to tell customers. It is obvious that this microwave is faulty from the get go, and they just keep on making them the same way and not trying to fix the problem.