I got a Whirpool Cabrio Washer that I purchased in 2008. I am constantly getting ul code. If washer is leveled, it leaks water out the bottom rear of the washer. Its a piece of junk. I called Whirpool to no avail. Whirpool will not stand behind their product. They know they have a problem but wont do anything about it.

Updated on 03/15/2020: We bought this eight years ago to replace a 20-year-old Maytag that had finally developed a rust-related leak after serving us faithfully and needing only one almost trivial repair ($10 DIY lid switch replacement) over that period. I have replaced the water pump, the gear case, rotating seal (3 times), the lid switch striker (3 times), and the replacement gear case is making noises indicating incipient bearing failure. In its finite wisdom, Whirlpool decided to make the failure-prone main bearing irreplaceable, which means you have to replace the entire gear case, at a best-case cost of $120 and a worst-case cost of $300, plus labor, unless you do the work yourself, as I do. The secondary issue is mold and a musty odor. The most effective way to eliminate this is to pull the drum (non-trivial, requires a car jack, a 2x4, and a special spanner/wrench) and swab down the inside of the tub with disinfectant. (Been there ... done that three times over 8 years.)Original Review: I am in the process of replacing the bottom seal on my 6-year-old Whirlpool Cabrio (WTW5500XW2) washer. This will be the fourth major repair I have done on it. Fortunately, I can do the work myself and know how to find the best price on parts, but it is still discouraging that a lightly-used washer would have so many problems in such as short time. (It replaced a 20-year-old Maytag that finally rusted out.) Repairs to date: 1) replaced drain pump motor; 2) replaced lid switch; 3) removed basket twice to clean outer tub, due to mold and odors; 4) replaced suspension rods due to excessive spin vibration; 5) out of commission awaiting a new bottom seal. Total cost of parts (labor was on me) is well over $100.

I have had my Whirlpool Cabrio washing machine for 14 years. I feel this is very dependable and cleans my clothes efficiently. I love the large stainless steel tub without the agitator. I can fit a king size comforter in the machine. The only problem I had with it was to clean the lint out which I would assume would have to be done to any machine that is used every other day for 14 years. Love it!

Tried to do a small 2x3 bathroom rug and the spin was thrown off kilter. I have been doing laundry a long time and I know how to evenly distribute clothes etc so the washer should be able to handle it for the price I paid. The high end front loading Whirlpool set.

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

I recently just purchased a new home with an upgrade provided by the builder (which I paid), kitchen appliances to Whirlpool Gold package. 2 weeks from the time the house closed escrow, I used my Whirlpool Gold Accu Bake wall oven self-clean feature. I set it for 2 1/2 hours, which is not even a full cycle of 4 hours. I noticed after 2 hours that the oven shut down. The oven exhaust was hot and the panel control as well, (almost burned my hand). No power and door locked. After a week of waiting to cool down hoping it will unlock and turn back on, it didnt. I called the builder and Whirlpool. Of course, the builder said to call Whirlpool. They registered my oven and set an appointment. The contractor (A&E) came to take a look at my oven and assumed that it was just thermal fuse. He was explaining that the oven does heat up and shut down. Probably after this repair, this will happen again. He replaced the thermal fuse and tried to turn on the oven. The house electric breaker is working, but the oven still did not turn on. So this time, he checked the control board and said that it is dead and will have to order. I am tired of having an oven for 2 weeks only and already have this issue. I did find out as well online that Whirlpool do have several complaints regarding their self-cleaning oven. I want to either just replace the whole oven or give me cash so I can replace the Whirlpool and buy another brand. I dont see the point of having a self-cleaning oven if this will heat up and shut down the unit or get a suggestion not to use the self-cleaning feature anymore so it wont break. I think this is a design issue and Whirlpool is not taking the responsibility to fix the design to start.

On July 19, I was forced to buy a new washer. Bought a Frigidaire which, when connected to the water supply, started immediately dumping water into the drum. Sent this defective washer back to the retailer and chose a new Whirlpool. O-M-I-G-O-S-H! It was delivered on 25 July and despite having 4 temperature settings, it only worked on either hot or cold AND you could never tell what temperature was going to be chosen by this computerized wonder. I repeatedly called Customer Support and received three different answers on what temperature was considered warm. The answers ranged from 65 to 102 degrees. Also, you could open the lid when the water was running in, which washers are no longer supposed to do. Whirlpool then arranged for A & D Service to come and repair my NEW washer and scheduled an appointment for a week later. I was forced to call that company to find out if they were even coming. When they did not show as promised, I cancelled the appointment and called Whirlpool to ask for another service company. They then scheduled me for two weeks later (now August 30th). The guy did come and told me there was user error - I had used too much soap as this was an HE washer. I asked him to show me where on the appliance and in the owners manual that it stated the washer was an HE. He couldnt find it either and said he would replace the computer and the door lock because his computer found that the washer was hit and miss on anything it was set on. At any rate, it is a little over a week later and I have heard nothing from the repairman and, of course, no follow-up from Whirlpool. Do not make the mistake of buying any Whirlpool product, and that now encompasses names such as Maytag, Amana, Jenn-Air, Kitchen-Aid and many more if you want to be assured of a quality product and excellent customer service. What if this had been a refrigerator? The whole debacle has been a nightmare. Wish I had bought a GE!

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

Whirlpool Dishwasher Model WDT7820PADMO was installed last October. Small parts began detaching themselves from the first day. Then machine leaked onto floor two weeks ago and I shut it down. As it was purchased from Sears, they and Whirlpool have batted responsibility for repairs back and forth until proof of extended warranty was supplied to Whirlpool. They then scheduled a repair job for a week later with an unqualified technician, who naturally refused the job. Upon callback, I was rescheduled for a day two weeks hence. As it turned out, the repairman would not be near my home on the appointment date. Luckily, I tried to move the appointment up, as the repair service said Whirlpool did not supply proof of the extended warranty. I saved five days waiting time by rescheduling, but have to supply proof of extended warranty yet again. All this for a dishwasher that takes three hours per load, and doesnt do a particularly good job of cleaning.

I bought a dishwasher Gold Series Top Control Whirlpool dishwasher at the Home Depot, April 4, 2015. Paid six hundred ten dollars and twenty-eight cents $610. 28. I noticed soon after that the top shelf falls off the rack when loading at front. I began loading from the back. It worked for a while but now it totally fall apart. The door will not close and I am unable to use the machine.

If you are thinking of buying any Whirlpool products, please think twice. We had a dishwasher, lasted 2 years; range with cook-top, within 2 years computer had to be replaced and again in another 2 years. Needless to say we did not replace either one with a Whirlpool. Over the range Microwave Oven Magnetron blows in 5 years. 3 months over the warranty. In a call to Whirlpool we were told we are sorry you have had all this trouble, we will send a repair man out and he can replace the parts needed. Thanks, but no thanks and went out and purchased a Samsung model, probably cheaper than the repairs would have cost us. There are so many good appliances to choose from. Please stay away from any Whirlpool products, no need for additional aggravation.

I bought the Whirlpool Cabrio topload washer (WTW7800XW2) in April 2011. In May 2012, I noticed the door was broken on both sides. It has now popped up and is broken so bad that it can barely be used without replacing it. I called Lowes, where it was purchased, to quickly be told that there was nothing they could do because it is out of the years warranty. This is just such a copy out to have an excuse, so that they would not even offer any assistance. Also, I paid $2,000.00 for the set; I bought the dryer as well. I just could not imagine an expensive machine like this having such a problem. Prior to buying this machine, I had my washer for 10 years. It has no problem; it was just time to buy a newer model, so I thought!After the store (Lowes) would not help, I decided to call Whirlpool; and the woman I spoke with was even less help. Andrea said there was nothing they could do since it was outside the year of manufacturers warranty. She seemed glad to have this as an excuse. I told her this is too much money to have something like this to happen. I told her it is obvious the door was defective. She said again sorry but that theres nothing she could do. She did offer to sell me a warranty for a year for $327.52. This was too expensive. I asked her what else could she do, and she told me nothing. I asked how much the door was, and she told me $212.00. I feel like I have been royally and deliberately ripped off, and Whirlpool knows it. I say to anyone reading this to please be aware if you are purchasing this product. You will most likely be sorry you invested all this money for it. You will get a companys brand that does not care and will not stand by their product.

Whirlpool side by side refrigerator/freezer Model #GSF26C5EXB. LESS than five years old and the ice maker is not working! Bought at Lowes. Great service. Out of warranty now. Lowes sent a repairman and it has to be replaced. I called Whirlpool and they said sorry. THATS IT? Ice makers dont ever last five years now? Unreal!

I had kenmore in long term until we decided to change the brand Whirlpool. We just saw want to updates to change the color. It was good price on special day. I have no problem with the stove. I like there is size of pots from small to large pot of size.

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

I paid $1246 for a Whirlpool glass top range. This was not a cheap model, but I wanted it as the starting point of my new kitchen. After only about a year, we noticed that the area surrounding the operation controls was turning a funny color. On closer inspection, we noticed what appeared to be something peeling off, it was paint! The area surrounding the controls, which appeared to be brushed metal, was actually painted plastic! I was furious that an appliance at this cost level was made of plastic....really, a stove top made of painted plastic? I complained and after a huge fuss they agreed to come out and replace it ONCE. Well its been just over a year since they replaced it, and guess what? It is peeling off again!I dont know what to do, as Whirlpool obviously has gone the cheap end and doesnt want to fix problems. As others have mentioned, they say that it is JUST cosmetic, and they wont cover it under warranty...now my first new appliance for my first new kitchen since 1972 looks like crap! I should have kept my old avocado green appliances - they lasted over 40 years, still worked, and still looked good (except they were green). I wont ever buy another Whirlpool appliance. For those who mentioned that their appliance would turn on unexpectedly, please check recalls....this is one of the major problems on recall. Buyer beware!!!!

The exterior look of the refrigerator (WRX735SDBM00) is impressive and the stainless steel does not show finger prints easily. It has two french doors on top, a middle drawer, and the freezer drawer on the bottom. The interior is 25 cf, but there isnt much space, even with reconfiguring the shelves, and the crisper/meat drawers are so small, that a large bell pepper wont fit. When one French door is closed it pops open the other door, which then does not close back tightly. Although there is an alarm system to warn a door is open, it only works if the doors are open and not just cracked. We have to constantly push on both doors to be sure they are closed tightly, even after washing down the gasket to get a better seal.

I have owned a Whirlpool Cabrio HE WTW6400SW3 for two years and have had nothing but issues from the start. Control panel was replaced twice under warranty. Also the clothes (socks underwear) were under the tub blocking the drain. This is not covered under the warranty. I was told by the repairman that this is the usual issue. He told me they took the front loader design and just stood it up with no protection from garments and coins getting under the tub, through the under tub filter often and into the drain pump. You are kidding me? Almost $1000 for this washer and its so ill designed. I have read forums that this has been an ongoing issue for several years yet Whirlpool continues to build these. I dont vent to forums often but just now I finished removing the tub to remove 2 socks and 7 cents. Also, I had to remove the drain pump and found another 16 cents inside it. So far the pump has not been ruined but this time water is coming out from the machine so will probably be ordering another pump for it as well. The wife wants it out of the house tomorrow and not another cent spent on it. But it is only two years old. What do you do? If you are reading this because you are searching for a new washer do not purchase a Whirlpool! I have gotten nothing but grief and was put off by their customer service dept as well. I guess after fielding so many calls about the same thing they have been told to just put all the calls off as no big deal. I am sure Whirlpool is making a killing off the sales on this unit. The claims made during the sale convinced me. What a joke. Look around the internet and you will find hundreds if not thousands of the same issues.

The control panel is difficult to use. It’s much too easy to switch power from the top oven to the bottom oven without knowing it. In addition, the plastic cover over the control panel makes it difficult to use especially if your fingers have flour or oil on them. It would be much easier and more accurate if knobs were used to control the all the functions instead of a electronic screen. Also, the clock has never operated accurately. Always runs fast. Temperature of the ovens is pretty accurate. However, it does take a long time to reach chosen temperature. Both ovens are large and able to handle an 18 inch round pizza dish. Other than the control panel, I’m pleased with both the gas stove top and both electric ovens.

Our Whirlpool refrigerator was delivered July 27th, 2013 after waiting 6 weeks for it. I was getting something off the top shelf (side by side refrigerator) when a 2-liter plastic bottle fell and put a hole in the bottom shelf where it sticks out under the vegetable tray. I have had grandkids sometimes stand on that shelf of our other refrigerators without ever doing any damage to it. It makes me nervous of dropping something else. I would like to send a complaint directly to Whirlpool but dont know how to reach them.

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

Bought this unit for our daughter that lives in a apartment building. She loves it and keeping her cool at night.

My fridge is a French door-type with two doors on top and a pull-out freezer with a ton of room! There's water at the door and an amazing ice maker inside the freezer. Two drawers for veggies, fruit, meats/chicken. And a retractable shelf to make room for larger, taller items.

This is Whirlpool model MVWP835DC2. I bought brand new. Recently used about once a week. Got an alarm that indicated no communication to core unit. Talked to Whirlpool service and unit is out of warranty (20 months) and advised I should use authorized service company to come and diagnose. This took 2 weeks. Service man came, washer did not power up. He quoted that repairs would be $750 and not worth it, buy a new one. I went on internet and found YouTube videos that showed how to diagnose and fix. I called Whirlpool for new console, $350 and one month. Went to parts house and got part for $250. This fixed problem.I have a few problems with this machine and company. 1) This now turns out to be a known problem with these machines. The console fails. I am not sure how this is going to last 30 years. 2) Service man took nothing apart and could not diagnose problem with no power. He quoted $350 for the console and the balance for the core. He was guessing or pulling a scam. Take your choice.3) Part not available from Whirlpool because so many are failing.Thanks for making a great product.

I have been using Whirlpool products for quite sometime. I had bought a 3 door refrigerator (Protton) about 2 years back. However I am noticing that of late, the vegetable drawer does not cool to the appropriate temperature. The vegetables as a result are spoilt. I am unable to understand what to do. I have checked with the other temperature settings and they are all in the normal mode.

Whirlpool Cabrio washing machine is less than five years old. First repair was replacement of control panel (under warranty). Second, third and fourth attempts to fix the out-of-balance problem which continually caused the machine to shut down altogether (even a small load) left my repairman totally frustrated after replacing most of the parts, finally telling me it just cant be fixed! What? I paid over $1,000 for this machine in Oct. 2007 and expected it to last many, many years. My mother-in-law has a washing machine she bought used in 1979 and it is still working beautifully. Ive read the 14 pages of complaints on the Consumer Affairs website and agree with Diana in Kissimmee, Fl - I am sick to my stomach not only for Whirlpool not recalling the Cabrio, but for Lowes and Sears and any other supposedly family-friendly business for continuing to sell it! Someone please contact me if you know of a class action suit being filed.

I purchased Whirlpool Cabrio on 04/06/2017 at Best Buy in Lake Worth. The washer stopped working last month. I went to Best Buy to complain. I was told to contact Whirlpool which l did. Was on the phone for over 2 hours with representatives. Finally l was told a service person will come take a look and tell me whats wrong with it. The service person came after one week out. Told me he has to order parts and it will take a week for the parts to come in. That his company may send some else to come and fit the washer. Meanwhile l took off the day from work.Now today 08/08/2017 the service company that Whirlpool contract with sent another service person with the parts only for him not to be able to repair the washer. He has to order more parts and it will take another week or so. I was so upset called Whirlpool, spoke with two different representatives. All they could say is sorry for the inconvenience that l have to wait until the service person comes out again with the parts. And if he cant fit thats when they will be able tell me if it will be replace. Bottom line is that l will never ever buy Whirlpool products again.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

Whirlpool g2 convect/micro over the stove oven - This top of the line oven is JUNK, KEEP YOUR MONEY-DO NOT BUY THIS JUNK! I have had problem after problem. Starting after only three months. Defected door switch, touch screen, flashing screen, error message. The service repairman and I are on first name bases. Thank goodness for the, out of my pocket warranty which I no longer plan to keep. I NEED A OVEN AND DEFINITELY NOT A WHIRLPOOL.

We bought the Whirlpool Duet set for $1,000 18 months ago. About four months ago, it started shredding our clothes. I would get them out with holes in them, but there was nothing sharp in the washer. Then the grey outside seal started deteriorating and getting tiny balls of rubber all over my clothes, ruining several white shirts. It always smells like mold. I just went to get my clothes out of it to find out it leaked water all over with that disintegrated rubber from the seal. The seal had completely ripped from the top to the bottom drain for no apparent reason. Now we are replacing the below. We JUST paid it off this month. It is crazy, it is already breaking!

Whirlpool washing machine has always been reliable for me. I have owned 2 and they lasted me many many years. Its easy to use, and cleans clothes perfectly. My family is also a fan of Whirlpool appliances.

We purchased a water heater at Lowes. Our old water heater had an issue but we always had good water pressure with the hot water until we made the horrendous mistake to purchase at LOWES - the worst possible place to buy a water heater. They sent the water heater and we had to look for someone to connect the WHIRLPOOL WATER HEATER (the runaway water heater). When it was installed the water pressure at my home was so bad that only one shower can be used at a time. This never happened before with the old water heater, there was no pressure at all.We called LOWES the WORST PLACE TO BUY A WATER HEATER, they did not accept any responsibility and they sent me to the Technician that Lowes has in DENVER to fix the problem. This bad company (WHIRLPOOL) sent us a crooked technician who wanted to charge us $600 dollars to repair something other than the water heater. We did not trust this person and we called another technician who told us that the water heater is not working properly. There is no one at LOWES and NO ONE at the Whirlpool customer service who can help us with this disgraceful water heater.DONT BUY WHIRLPOOL WATER HEATERS. DONT BUY AT LOWES!!! They are crooks! They do not respond for their products. They do not want to exchange the damn water heater as HOME DEPOT would. Buy everything at HOME DEPOT! Run away from Lowes! They dont stand behind their products, they send you all the work and if you have something wrong with your purchase they will not help you.

It is a good refrigerator for the price, but it is not big enough for our family. It does get very cold in the refrigerator part unlike our last refrigerator. I only wish it had more shelf space on the door and the egg place fit more than 6 eggs.

We bought a gas hot water heater from Lowes on Dec. 31, 2010. In July 2011, there was no hot water. After much yelling and headaches, Whirlpool agreed to send out a technician to look at it, since I refuse to go in the attic and I will not work on gas appliances. After 7 days with no hot water, they replaced a valve that failed, they said, because our attic was too hot. The old unit never complained. Eight months later out, the unit went again (and we had an attic fan put in). This time, Whirlpool sent out a local plumber (and I paid for the call) though we had a warranty and extended plan with Lowes?! This time I was told no problem it was too windy and it blew out the pilot. Its funny we never noticed the attic being windy even during the hurricanes. Four to 5 months later, well, you guessed it but this time my husband just re-lit it. Then the next time, 5 months later, my brother-in-law did it. That was August to September 2012. See, this morning, there is no hot water. I had to fight with Lowes since we have the 5-year extended plan. I cannot get anyone to explain why it makes sense to them that a 2 1/2 year old hot water heater has to be re-lit every 4-6 months. Then I went online. Now I know why Lowes and Whirlpool are ignoring the issue. So, anyone know a good lawyer or what are they doing to get satisfaction?

Sixteen months after I bought the Cabrio washer (model # WTW7800XWO), the F1 error light came on. I had to replace the electronic panel on the machine for $400. Whirlpool refused to replace it even though they have been replacing this panel for others. This is a common problem with the Cabrio washer.

On the 10-05-05, I purchased a Whirlpool natural gas water heater from Lows Orem. The unit has a 9 years warranty agreement. Lows sales S0178JC3 647605; cost $378. Model number FG1H5040T3. Serial number 0515140765. Following installation, the unit has failed repeatedly. Since keeping records of the failures, the unit failed either by the gas control valve or the thermocouple on December 2011, November 2011, April 2010, February 2009, and April 2008. Whirlpool has at all times supplied the parts but denied that the parts are technically faulted. Whirlpool has further rejected all requests to refund me for defective product. The major consequences have been an unreliable water heater. There were periods without hot water. Time was spent involving undertaking repairs.

After 1 year and 5 months, my old side by side Whirlpool refrigerator stopped working. The melted ice caused floor damage and ceiling damage of the floor under.

I stumbled across this page on another mission and had to stop to add my exp. Perhaps I got lucky and got a good set but Im on my 3rd year and my washer and dryer are my friends. I dont have hot water connected to my washer and my husband is a shingle roofer so I often have to wash his clothes twice but my dogs beds come out beautiful and the sanitizer on the dryer removes odors very well. My water bill went down, I can wash my rugs and large comforters at home now. Plus they are so pretty. Im sorry you are all having so much trouble but I love mine sooo much I just had to stop a moment to throw in a little positive.

I bought Whirlpool water heater model #FG1H5040T3NOV about 5 years ago. Burner assembly was replaced two years ago and now, thermocouple was replaced yesterday.

Do NOT buy this washing machine. It looks nice but that is all. My elderly parents bought this washing machine based on the past experiences with Whirlpool but the quality of the product has changed. This machine constantly errors and does not allow them to wash clothes. I have followed the instructions in the manual to try and clear the errors. I ended up calling Whirlpool and the response I got was... It will be anywhere from $80 to $125 for someone to come out and look at it. This is a product which should not stop working after 2 years. I guess Whirlpool only stands by their products for a year because they think it is only built for a years worth of service. I wish I had better things to say because the previous Whirlpool machine lasted over 20 years.

I love my washer and dryer. The only problem I had over the past five years since I bought them was when the motherboard went out on the dryer. Luckily I had insurance, so was able to have it replaced. The features on the machines and their ability to clean really well have made my life much easier when it comes to doing laundry!

In 2008, we purchased a Whirlpool Gas Water Heater from Lowes. Three years later the tank started leaking (this water heater had a 6-year warranty). Per Whirlpools instructions we were to return this one to Lowes for a refund (in hindsight we should have taken the money & went elsewhere to purchase a better brand!). As our plumber was removing the leaking heater we went to Lowes to purchase a new Whirlpool Water Heater upgrading to one with a 12-year warranty hoping that this one would last, it was advertised as the BEST one Lowes sells! After our plumber swapped out the heaters we returned the leaking water heater for our refund (remember this one had a 6-year warranty & only lasted 3 years).This past June (2015) our water heater stopped working, turns out the thermocouple went out which shuts the gas valve off. Called 5 plumbing companies in the Metro Phoenix area, not a single one would work on it! We researched the repair, called Whirlpool & was told that this water heater was out of warranty. Wait a minute! This one has a 12-year warranty & it is only 4 years old! Whirlpool told me that it is a replacement water heater so the warranty for this water heater is only 6 years (from the 2008 date of the purchase of the first water heater). It didnt matter that the replacement water heater was a different model & was more expensive than what was refunded to us. We replaced the thermocouple ourselves & got it going again. Last week it started leaking, called Whirlpool again got the runaround again, called a plumber who replaced it with a new Ruud for $1000.00 (Water heater + Labor).We went back to Lowes to try to get their help resolving this, the store manager said this was a Whirlpool warranty issue. We ended up taking the junk Whirlpool water heater to a recycling facility and getting $2.50 for it. Bottom LINE!! READ THE REVIEWS, THEY ARE TRUE!!! There was a class action lawsuit with a settlement of which I never received a notice for, I read about it online this summer, but it was too late to opt in. Dont waste your money on Whirlpool water heaters, no one will repair them, Lowes wont stand behind the products on their shelves, they get your money & hide behind the manufacturer & Whirlpool has very nice script to get you off of phone! Whirlpool used to be a trusted brand (do your research, I think they are the manufacturer for certain store brands! ). Our new Ruud water heater has a faster recovery than either of the Whirlpools that weve had; the drain valve is brass, not plastic like the whirlpool, it is overall a much higher quality.

I purchased this dishwasher washer (Model WDT710Paym3) in May 2013, quit cleaning. I have checked filter. I run this washer 1 or 2 times a week. Very disappointed in washer and the quality of the product. Dont think my next purchase will be a Whirlpool.

Friends and family dont you ever dare to buy a refrigerator from Whirlpool - Best Buy!!! They sold me a defect refrigerator and after 2 months begging to see a technician, they are telling me that they are going to fix it. Im so tired of them trying to fix it. Theyve been here 4 times with no luck. All my food is rotten and frozen. And its a new refrigerator. Gosh. As you can see, the water in the plastic cup that I left in my refrigerator are frozen which is not supposed to happen. I feel that Im dealing with nonsense. They dont care. They just took my money and thats it. Im left with a new defect refrigerator that doesnt work. Ridiculous.

The felt drum gasket came off our 6 month old Whirlpool Cabrio dryer purchased through KB homes. When I contacted the helpline on the 16th of May I was promptly set up with an appointment on the 18th of May. On the 18th I called to confirm a time and the company that whirlpool subcontracts in San Antonio, said they had no appointment for that day and the soonest they could get out here was June 1. I contacted Whirlpool to let them know this wasnt acceptable and I received many apologies and I understand how you feels. I asked how is it you have one company in all of San Antonio to service our dryer? Again more apologies. Then I asked since when does only apologizing and saying, I understand your feeling, be the end all of your customer service? No reply to that so I called Sears who promptly had a repairman out to the tune of $200 bucks with my military discount. Never again Whirlpool.

I am a working single man. I needed a used washer. I shopped the new washers but they were a lotta money. I seen many of them were without agitators. Well heck... who am I to judge the progress in technology?? So, going around to the used appliance store I run across this Whirlpool Cabrio. OK, Whirlpool meant quality my entire life. So, I bought it. MASSIVE MISTAKE!!! This POS is no washing machine. I dont know what it is, but it is NO washing machine! It is a machine that runs a very few gallons of water into a load of clothes and makes them wet, and that is about it!!All I know is the federal government is dropping the ball on this situation BIG TIME!! To allow a company to foist off on consumers such a PILE OF JUNK!! The pile of crap is PURE junk as far as simply doing its job... washing clothes!! It is a DISGRACE of an American product, and I will NEVER buy anything made by Whirlpool the rest of my life!!I took the device off the lid that tells it when the lid is closed, and just stuck it in its receptacle in the body... so I could raise the lid while it is running and watch this POS in action and try and figure out what the hell is going on. First big problem is it NEEDS an agitator!! Obviously Whirlpool had not figured out how to make the clothes circulate without one. Second is the water level (no matter what cycle setting) is obscenely LOW!! The clothes do not circulate AT ALL, and about 1/3 of them do not even get below water level for the entire cycle!! What I am forced to do is use a water hose and run a lot more water off into the tub just to get the clothes in the damn water!! And ever at that, the clothes still do not circulate AT ALL!! They just rub up against each other!! And I have to use twice as much soap than called for!!

I had the junky gas water heater for two years and cant keep the thing lit. Calling Whirlpool does no good. They give you the runaround; the store cant do anything. They know they have a faulty product and keep selling it. Some companies are only out for the money. If that wasnt the case, they would discontinue the junk. They will send you replacement parts but if you know nothing about them, you have to put out more money for someone to come and fix it. I would love to send them the bill! I would not recommend this brand of anything to anyone.

This has been our second Whirlpool Hot Water Tank in our home in the past 14 years. The first was installed by the builder, when it went out we purchased a larger capacity one from Lowes. It was professionally installed and now, after the extended warranty coverage period is expired, its expired as well. I would think you should be able to get more than 7 years out of not one, but two Whirlpool hot water tanks. No wonder they are no longer manufacturing hot water tanks - they sucked at it. Also, if you do have one, you have to get parts from Whirlpool and pay $30 shipping. No thanks, for the cost of parts to replace everything youre better off getting a whole new unit.

I have purchased Protton 3 door (Protton 20142, S.N **) fridge in Mar 2016 and since purchase of the fridge I have facing cooling issue. Its take around 24 hours to make ice. After sales service is also pathetic because after raised request the service person came about 6 or 7 days later, and he did not check anything and recommend me to go to the service center. I am not sure why Whirlpool kept this type service person and service. My concern is if Whirlpool is not ready to provide home service then should mentioned in service commitment we dont provide home service. I am using first time Whirlpool product and I realized Whirlpool product are very bad and service is also too bad. I strongly recommend to everyone please dont buy the Whirlpool product and I also want to know either Whirlpool will provide service or this fridge product is useless for me.

Purchased this dishwasher in January 2012, and it stopped working in May 2015. We replaced thermal fuse a year ago and just had to replace the control panel. It worked for 1 day and through 2 wash cycles, but during the 3rd wash cycle, it failed to drain and no power again, which is the same problem we had before. We opted to also replace the control board, just to be safe. Lol. What a piece of junk! Whirlpool is a pathetic excuse for a company, and, judging from others experiences with the customer service department, we will not bother contacting these ** since they clearly have no interest in providing any service at all to their customers. I have had many other lower end dishwasher models, and all of them worked well past the 5 - 10 year mark and never stopped working or required any service. I WILL NEVER PURCHASE ANOTHER APPLIANCE FROM WHIRLPOOL AND HAVE SPREAD THE WORD TO EVERYONE I KNOW. Good luck, Whirlpool. I do not expect they will be around in 10 years. Lol. Do not give your hard earned money to these idiots for the junk that they peddle, and please let your local appliance dealer know why you wish to purchase any other brand BUT Whirlpool. Consumers are not stupid, Whirlpool! You are ignorant for banking on that and should be shut down for your unfair business practices, not to mention misrepresentation of your despicable products.

We get the error code F1 in the start of the cycle and when there is 21 minutes left, we have to stop and reset at least 7 times before the water fills. We put a new sensor in for over $200. The second problem is it goes off balance no matter what the load is. I was going to have it fixed (if possible). After reading all the above I wont waste any more money on it and go buy an old fashioned reliable washer. What a piece of money sucking machine especially when I dont have any extra money to waste down the drain. I wish I knew before. There are a lot of people this time of year I would have rather given the money for a needy cause. How disappointed we are with Whirlpool!

We had to have a sensor switch installed. We purchased this washer, plus the matching dryer June 10, 2010. This was just 16 months ago today.The cost of this repair was $160.24, for part labor and service call. The service call was excellent. Wish I could say the same for washer.We had previously owned a KitchenAid washer for over 20 years (before purchasing Whirlpool washer) and did not have to have one repair on it. Very doubtful I will purchase another Whirlpool.Looks like quality is a thing of the past.

We moved into our new condo a few months ago and my wife noticed that the knobs and front of our new Whirlpool Stove were getting too hot to touch so we called Whirlpool and since then never used stove. Was over one year old, we had to call their factor service representative. The charge was $98 plus labor $90 to tell us that even though the surfaces were way too hot to touch and dangerous to touch they were still within the factory specs of 167 degrees for the knobs, 152 degrees for the drawer, and 172 degrees for the front glass. He found the front of the unit reached 152 degrees which was hot enough to cause a serious burn when the stove was only set to 400 degrees. Why would a company set specs that will cause serious injuries? If my wife or grandchildren get burned by this crappy stove Whirlpool will be hearing from my lawyer. Stay away from any Aquaclean Whirlpool stove.

My Whirlpool Duet washer was purchased on August 2006. The first one had to be replaced as it flooded my laundry room on the first floor and the basement – not once but twice. When I was told that they would send yet another service person out to try and fix it, I told them it would be at the curb and that I was looking forward to filing a lawsuit. Then after being on hold for forever and getting the company that sold me the unit involved, they replaced the washer at no charge.From day one I hated this washer machine. If you failed to take the clothes out immediately after washing, they would get a musty type odor and I never felt the clothes got cleaned enough. Yesterday, I went to empty a load of laundry and it was soaking wet with water pooling in the bottom of the barrel. Today, I had a certified Whirlpool tech come and look at the washer and he told me to put it at the curb as the rear bearing is shot and needed to be replaced. He also told me not to buy another front loader and the cost of the repair would be approximately $800.Thank you to Whirlpool for manufacturing a true hunk of crap that, may I say, cost me $1300. I will make sure I tell everyone I know that your products are crap and I would rather wash my clothes by hand. I did call the WP customer service number and was told that this is unheard of and that these machines rarely have any problems. After just reading multiple complaints of the exact same problem, I now know that this product is inferior and the design of the bearing assembly is seriously flawed. A major recall is probably in the near future and Whirlpool is hoping that most people will just dump them before the recall is made public.

I thought the new AquaLift cleaning would be the greatest. Boy, was I disappointed -- no thoroughly disgusted and very angry -- when I tried to use the self cleaning oven. I had cooked a prime rib roast and a lot of grease had spattered inside the oven. I wiped away the excess and did a cleaning cycle -- what a joke! There was still grease running down the door and walls. Nothing was changed after two cleaning cycles. Now I have to crawl inside the oven and scrub it manually. I was always pleased with the old self cleaning ovens which only left some ash and a little bit to clean up. The AquaLift technology doesnt work at all, didnt Whirlpool test it prior to selling it to the public? They will surely lose my business and I hope a lot of other peoples business as well. This technology was a huge mistake!!

Its not even a year since I have had this washer / dryer--and I already made two service calls regarding the dryer. The washer does not get the clothes clean. When washing even one blanket, it bumps, grinds and does not wash well. I have had to do two loads compared to one in my Amana set. It is terrible. You have to stay with it while washing or always load. It gets uneven with any small load. Everyone I know hates this washer.

I have recently bought a Whirlpool Cabrio washer/dryer combo and I wish I had read your reviews before doing so. I spend quite an amount of time washing, re washing, rinsing dark clothes to end up washing them by hand as the washer leaves unsightly white streaks on them. I have tried switching from hot water to cold, using very little detergent, buying clear detergent, then organic detergent, extra rinsing, etc. to no avail. Very frustrated and disappointed. I would gladly join any class action to stop Whirlpool selling these useless but expensive washers.

I was under the impression Whirlpool washers were good. Mine always goes off balance and quits. I carefully redistribute the load several times to get it to finish (start over). Sometimes it works fine from the get-go, but not often enough. It is now 2 years old and if I were wealthy, Id shove it to the curb. There is little to like with an appliance that often must be adjusted and re-started. I will try Samsung next. It seems that American brands are not reliable. I have no special needs and will consider reliability above all. The name Whirlpool would be a deal breaker for me. I cannot abide my Whirlpool washing machine as it is more of an aggravation than something useful. Stay away from Whirlpool washing machines. They (at least mine) require the load to be balanced to a microgram. Appliances should just work and not require fiddling with.

I have a Whirlpool refrigerator and it is the 2nd one in 12 months. The first one the refrigerator was freezing food in the fridge part and thawing food in the freezer part. After several times a technician came to try to fix the problem and arguments with Whirlpool. They finally replaced the refrigerator. The new one is now doing the same thing. I am contacting Whirlpool tomorrow.

Purchased brand new washer & dryer that was chosen specifically for its HE & washing capabilities as Im a single mom with 5 kids, 2 of whom have disabilities, & I need a good washer & dryer. Washer and dryer both broke several times. I paid for an extended warranty but they never resolved the issue. Called Whirlpool & they didnt care. Four years later, Im using a set I bought used that rips my clothes while the washer & dryer sit still broken. Will never buy from Whirlpool or Kettles again.

I love my stove and all of its features. My stove is easy to clean and I Love the self cleaning oven. I have a flat top so that helps when it comes to cleaning, not to mention it makes cooking a breeze. I love all the push buttons and how smart my stove is. I highly recommend my Whirlpool to anyone looking for a great appliance.

Once again I am disappointed in a product that I felt was of the utmost quality. However after buying in 2010 and not being installed until 2011, the over the oven microwave has a crack on the outside of the door. Two pieces have fallen off from under the plastic rim on the inside of the door, two pieces of the door one on the top right side and the other on the bottom right side have fallen off. All I have to say is the two Whirlpool products I bought at Lowes has been a huge disappointment especially since the other two bought from the same stores are Frigidaires and work beautifully...

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

I purchased a brand new refrigerator model # WRX735SDBM00 Ser # K51621170 on 30 June at Lowes. Paid about 1600.00. Within 5 days the ice maker was no longer functioning. I called the service department and a lengthy ordeal commenced of trying to repair. It is now 13 August 2015 and I have had over 10 visits from a technician and I still have no ice. I made a terrible mistake in not returning the appliance to the store within 30 days so now it has to go through the process which means that now I have to continue to wait until the technicians deem that this appliance is not repairable anymore before I can attempt to get a replacement.In the meantime, we have been inconvenienced, aggravated not to mention not be provided a product that works with no future date where I can get this appliance repaired. The local store management have been great to deal with and are trying but their hands are tied until the manufacturer determines they cant fix. In the meantime, the consumer is continuing to wait for the repair/replacement. No one seems to care or has there been any discussion of some compensation (not necessarily money) for the aggravation and inconvenience I have endured. Something is just not right. Suffice to say, never again will I buy a Whirlpool. HORRIBLE EXPERIENCE.

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

It has performed perfectly for the past eight or nine years. Only problem has been little plastic parts broke that held one big drawer that we may have overloaded. Door shelf plastic part holding it on... broke also.

Whirpool has its main washers, then the off brand of Whirlpool. After using the washer after a few months the balance starts to get off balance. Trying to find parts and get them put in is easy, hard part is replacing them after they wear off after use a few months.

The home I bought a few years ago, had brand new Whirlpool appliances. The oven and range, work great, although it does take my oven seems like a long time to get to temperature. The size of the oven is great, has plenty of room to cook lots and/or large amounts. The range, works really good too. Its a glass top range. The glass is very durable, I find it does not scratch easily. Cleans up well by just using a good glass top cleaner. I do have one of the burners, does make a little noise if used but 4 years in, no issues out of the range or oven.

Purchased a Cabrio large capacity washer. It NEVER seemed to get the clothes clean enough, and after the sensors and bearings went bad within three years (out of warranty of course) I gladly kicked it to the curb. I bought a Samsung that has been great. Id like to support USA made, but not when it is AWFUL.

We are on our 3rd washer and second dryer in 10 years. Our latest replacement (Whirlpool Duet Washer and Dryer) was purchased 3 months ago and is already broken and now we have been without a washer for a whole month. Not only do they have issues with the control panel and latch, but they smell. The dryer also had a control panel issue. Trying to get our units fixed presented even more problems and wrong parts would come in, with weeks going by without parts/service. Apologies and sympathies expressed on the phone are not enough. When you buy a matching set and only one breaks, you tend to replace the matching unit, which we regret and we went back and forth with our washer and dryer. I would never recommend a Whirlpool product after this. We finally got a replacement today and due to more poor communication on their end, they could not hook up. My new washer sits in the laundry room, and I hate it before I even get it hooked up.

I purchased a Whirlpool duet, model #wfw9550ww00, two years ago with added warranty. The machine stops mid-cycle. The time remaining flashes but no error code. Pressing start would begin the machine again. Sometimes, we could go several loads with no problems and other times it will stop three or four times in one load. Occasionally, pressing start would not work and the machine would require unplugging and restarting. We have had several service calls in. They have said it was the pump, then it was the motor, then it was the pressure switch, and yet the problem persists. They are due to come out again tomorrow for yet another examination to determine its cause. Its the third time in one month. Its a lemon.

Refrigerator was purchased in March 2015. Icemaker filled the basket two times then never worked properly again. The water would enter the tray, freeze, but never drop the cubes. In order to drop the cubes, we had to unplug the refrigerator for a moment then we would have those few cubes. We used one service company sent by Whirlpool that came 3 times, adjusted temp, and replaced one electrical part. It didnt work. The repairman was going to call for support from Whirlpool to see if anyone else had had this problem. I didnt hear back from him until I called him 1 1/2 weeks later. He basically said there was nothing else he could do. Whirlpool sent out another service company. He replaced 2 electrical parts. They didnt work. We have no choice but to keep having service men come out and try to repair the refrigerator. What happens when the warranty has expired? They are trying to sell me an extended warranty. Give me a break. It would be nice to have a working refrigerator first. I wish I would have read these reviews before I ever bought a Whirlpool. Im 78 and Im still learning. Never again, Whirlpool. Ill spread the news as well because we all work too hard for our money to throw it away on poor products.

We purchased the Cabrio Agi top loading washing machine in 2011 (3 years ago). After 2 years it started leaking from the plastic drum (Bearings?). Luckily we have it in the basement on concrete floor, so there was no damage, just frustration. This was poor purchase on our part. We should have searched for more reviews. The wash time is ridiculous; it is too long, an average of 50 minutes per load. I dont know about how clean the clothes were, I guess they were OK. I didnt notice a smell, or them looking dingy. The Cabrio is a piece of junk if the bearings went out after 2 years?? We just purchased a heavy duty Speed Queen, top loading, agitator washer. My wife loves this, its like the old Maytag we had. They told us they wont be selling these washers after next year. Buy them while you can. The Cabrio is headed to scrap yard.

Found after care service as bad as oven performance. Phoned for advice and told need to get used to new oven. My advice would be do not buy whirlpool ovens.

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

Whirlpool gold series gas oven with Aqua Lift. Very unhappy with this oven. Cons: Aqua Lift technology doesnt work AT ALL (manual cleaning required); stove top hard to clean; 2 front gas burners are super burners which is fine for boiling water, but too hot for regular cooking. Would be better to have one super burner in the middle or back but two up front is way too hot for regular cooking, even on lowest setting; oven cuts out while cooking -- unexplainable how this happens but you really have to watch the oven while cooking to make sure its still on. Pros: large oven so you can cook ginormous turkeys or prime ribs.

The unit I live in is at **. They purchased it in Nov 2011. The washing machine worked for 2 months. Now, it has to be dismantled at my home and take a day off. I would like a replacement. The Dutchgate is still being developed. They purchased at least 60 at this point, there is no reason not to give me a new one instead of having two techs dismantle the machine in my new home for 4 hours and a day off of work. Model WFC7500VWl, serial CD13528709. Please try to assist me.

Whirlpool Duet - Front loading with additional base makes loading and unloading easy. We have had the washer and Dryer about one year now. They were replacements for Kenmore front loaders. We replaced a Kenmore front loading pair that served us faithfully for more than ten years. But when we purchased a new house we decided that it was necessary to upgrade to better units. The Whirlpool Duet pair has performed exceptionally well with one little caveat. Periodically we have to unplug the units to reset the computers when they dont function properly. Small problem, easily solved.

Bought a Whirlpool stove five years ago when I got my kitchen remodeled. In fact bought all whirlpool appliances stove, microwave, dishwasher, and refrigerator. The dishwasher and refrigerator have already had some issues which to me were because cheaply made. The microwave and stove are fine.

We purchased a whirlpool gas dryer 30 years ago this past February. Its still going strong with 30 years of continuous use!! The only service ever required was a belt change I did myself 18 years ago. Not too bad whirlpool!!

I owned a Whirlpool Cabrio washing machine for 3 years (a two person household). The repairman just quoted $700 to repair a faulty center hub seal and bearing. This machine was not inexpensive. I expect more from a quality machine. A telephone call to Whirlpool resulted in two ten minute holds while being shuffled between representatives and each representative tried to sell me an extended warranty for another $289. Whirlpool should take full responsibility for this faulty product and not act like a telephone support center located in Eastern Europe. I am not pleased with this (lack of) resolution and do not plan to purchase another Whirlpool product.

I purchased a new French door refrigerator in May of 2016. Professionally installed. Last May 2017 icemaker stopped working and was replaced. June 2018 icemaker stopped working. This part of the refrigerator is poor quality and because of that I will never purchase another Whirlpool appliance. They use to be good quality and dependable. Not anymore.

I bought three Whirlpool appliances (fridge, gas dryer and washing machine) from Abt in June 2012, delivered in July 2012. The fridge has not cooled from the moment we plugged it in and because I am out of state from Abt (IL), I have to deal directly with Whirlpool. According to both the Whirlpool customer service rep and her supervisor, if a product is defective from the start, Whirlpools policy is to try and repair it until they determine it to be scrap and only then will they replace/refund. I find this policy appalling since I paid for a good working product, from a company Consumer Reports rates very highly, but was shipped a defective one. Now, I have had two service visits, the second because according to Whirlpool the first technician did not perform the correct service. I have been told not to put anything valuable into my freezer for 5-7 days because most likely I have a coolant leak and the fridge is bad. This is terrible customer service and instead of fixing their error which is the purpose of having customer service, they are quickly building a reputation for a terrible product and terrible service. Good customer service would be replacing the defective fridge as it is clearly their manufacturing issue, taking the item back to their warehouse, repairing it if possible and selling it as reconditioned for a discount. I am noting my suggestion in case any Whirlpool representatives read this website. Another interesting item to note is the gas dryers absorb air from the environment around them so if you do any painting (full room or touch ups), the clothes that come out of the dryer may have a burnt/gas smell for up to 7 days. I am still waiting to hear back from the Whirlpool technician as to my burnt smell problem/resolution, but was told this from a separate service representative so I thought I would pass it on.

I purchased this washer (Whirlpool Cabrio Model #WTW8000DW) 10-25-17 from Best Buy & now it has no power to the panel at all. The power to the outlet is fine which I can plug a hair dryer in & the hair dryer works. Tried all the reset buttons & options with nothing on the panel working as well as unplugging. Still nothing. It is barely 4 months old & I am very dissatisfied for the amount of money I paid for a high efficiency top loading washer.

There is a chronic and well-known problem with recent French door, bottom freezer refrigerators sold by Whirlpool, including the the brand names KitchenAid, Jenn-Air, Maytag, and Amana. The problem is caused when the defrost drain freezes, preventing defrosted water from reaching the evaporation pan. After enough water builds up, it overflows along the front of the refrigerator. In my particular case, we have wood floors and they were ruined by the water. After doing some investigation on the internet, I have learned that this problem affected approximately 1,500 model numbers sold under these names. These model numbers are listed in a Technical Service Pointer issued by Whirlpool.In August 2013, after experiencing several years of problems with these units, Whirlpool issued a Technical Service Pointer W10632338, advising service technicians that a new P Trap drain tube kit was now available, and suggesting that the defective duck bill check valve should be replaced by this new part. The problem for years had been that the rubber duck bill check valve would, over time, become sticky (or tacky) and would then not open - causing water to build up above it. Eventually, the water would freeze and since newly defrosted water could no longer escape, it would build up and eventually overflow.From what Ive seen online, plus a conversation with the Sears technician who come out to diagnose and repair my leak, I am convinced there are many thousands of customers who have experienced this problem. Because it takes a while for the rubber check valve to become sticky and no longer open, it is not uncommon for the problem to not appear until after the standard one-year warranty has expired. From reports, Whirlpool has sometimes acknowledged the problem and effected repair of refrigerators no longer under warranty.But what about those customers, like me, who have experienced water damage to floors and cabinets? Shouldnt Whirlpool be liable for those repairs, too? Id be interested to know if anyone knows of plans for a class action lawsuit.

This is a freezer on top unit. Purchased in 2015, unit quit cooling, started making a roaring noise. Called local technician, he added 2 oz of Freon, said he has seen many of these same unit losing Freon. Technician said line that goes to compressor is copper and hooks up to aluminum line before attaching to compressor. This is leak point for freon; no way to know when the leak started, but freon almost gone and cost to pressure check for source of leak is costly and probably would not repair problem. Got 6 yrs out of it and I am replacing with another brand. Will never buy Whirlpool again. Should have got 10-12 yrs of use. Do not buy this unit. Wrote Whirlpool first, but no help. Indicated this could be a problem with these units but no recall so I am on my own. Out $900 for a new refrigerator. Big hassle. Unit no good.

I am concerned that Whirlpool microwaves installed over the stove have extremely faulty doors. I have two homes in which I have Whirlpool microwaves, and both have huge cracks in the door and small pieces inside the doors beginning to fall out. It deeply concerns me that it will cost more to replace the doors than to replace the microwaves. I have always believed in Whirlpool appliances but now feel that I will have to change brands. My question is “What in the world is wrong with your doors that they crack so easily and the company holds no responsibility with such faulty work?” I would simply think that this was just a faulty door on my microwave, but I have two that are cracked! This definitely means you have a faulty product.

Bought these Whirlpool Cabrio Platinum combo about three years ago, nothing but junk from the get go! Washer never gets clothes clean, towels always come out smelling mildew and sour no matter what liquid soap you use Tide, Gain, whatever same results. Plus always mold coming from inside tub and yes we use refresh weekly and wash it out on refresh setting. I’m so tired of our towels smelling sour but can’t afford to buy new washer and dryer living on fixed income. If I could these would be in the recycling yard now. From everything I’m reading all new H e machines are crap and energy efficient my foot. I wish for my old style washer and dryer. WHIRLPOOL YOU HAVE LOST A LONG TIME CUSTOMER!

Very unhappy with my top load washing machine. I use more water. Can wash fewer clothes and clothes do not come as clean as with my older Whirlpool. This machine needs a SERIOUS AGITATOR. Will not buy another Whirlpool.

We bought a WRS325FDAM02 Side by Side Whirlpool Refrigerator and from day 1 we have been having problems with rust buildup on both doors. Bought it in July 2014 and have had the service people over to figure out the problem many times. They finally decided to replace the doors which didnt help because the replacement doors are doing the same thing. We have bought everything they told us to buy to clean and try and prevent the rust from coming back but nothing helps. Our warranty was ready to expire so we bought the extended warranty only to find out that cosmetic issues are not covered under the extended warranty plan... Stay away from this model refrigerator... Not only that we were then told the doors are not really Stainless Steel just some fake crap that looks like Stainless Steel. We paid good money for this refrigerator and have to deal with cleaning rust off the doors day after day.

Bought brand new, Whirlpool front load washer and dryer, from Corbeil. Got both items home and connected and levelled (yes I took out the shipping bolts). Did my first washing and watched my new washer dance across the floor. Called Corbeil and they told me no refunds. Best they could do was to send out a Tech to check it. Tech came, changed the shock absorbers, a token act because the machine danced as much as it did before. Please for your own well being DO NOT buy this product and DO NOT buy from Corbeil. There are other products on the market that advertise items that dont shake.

Like the load sensor feature the best, so economical, the drum is oversized to wash duvets and heavy blankets. The fact that the washer and dryer are stackable makes them ideal for apartment living.

The machine was great and handled large amounts of laundry. It was very expensive but my wife was happy with its performance. A year and a half into owning it, the electrical code F70 comes up and it stopped working. When I checked online, I found it is a common problem. I contacted whirlpool customer service and they could not do anything. Spoke to the manager, Kiesha and she refused to help me even though I bought both the washer and dryer for a lot of money. Customer service is not a priority evidently. She denies that there is an on-going problem when both the internet and my service tech say differently.

Purchase whirlpool washer model W2W4800xQ2 in Sept. 2012. Had problem with lid lock after warranty. Now lid lock does not work, takes 1/2 hour to start wash and does no spin. Called whirlpool and they will do nothing. Repair will be $200. I opt to just purchase new machine. This machine is one piece of garbage.

We went out and bought the new front loader washing machine and dryer. Neither one of them works correctly. A service call had to be made the the day we ran the first load. The washing machine only washes errors popping up F8 and E3. On the dryer error code E3 pops up and cannot dry clothes. Worst purchase I have ever made.

Bought a Whirlpool Cabrio washer from Home Depot. It started making noises on the spin cycle 2 months after the purchase. A technician came out and concluded it was a clothes hanger behind the machine making the noise. False. Two days later I tried to wash a load. All the panel lights came on. And then the machine died. No power. The tech came out and tried to run tests but the machine would not respond correctly. Informed it has a bad control. The machine will malfunction even if a button is pressed too long. And then its repairman time again. This machine is poorly designed. No doubt whoever designed the digital control panel did not think about ease of use. The tech has to recalibrate the controls after every failure. Whirlpool and Maytag have put out a bad product and this will be my last.

My Whirlpool microwave broke. Im not sure how or why so today I purchased another 2 actually. Both were too big. The model I purchased is discontinued. I had to remove part of my Marble Backsplash - the turntable is tiny however mic is huge. Work on making microwave for smaller areas. Stick to get or Samsung for a nice size microwave not a Mongo mega oven above your oven.

I do not know if my mail would be read or not, but I am writing it just to my satisfaction. I am a doctor (dentist) living in Haridwar. I had bought a Whirlpool fridge around 2-3 years back. I am not sure about the date. I have the bill. I will have to check the exact date. So around 3 months back, the fridge stopped cooling and I lodged a complaint in your customer care center. The engineer turned up, and he said that the compressor was not working and the company will change it. We only have to pay for the gas to be refilled. I said ok. Everything went well for nearly 3 months, then again one fine day, the cooling stopped. I called the companys customer care, and they gave me a complaint number and customer satisfaction number. But nobody turned up for 2 days. I called and called, then after much calling, a guy from the company came and said that the compressor was not working and they have to change it but that it will not be possible for 4 days. After 4 days, he will come.Sir, can you live without a fridge for 4 days and not getting the guarantee that it will be ok in the next 4 days? So, I went to the market bought a Kirloskar compressor, got it fixed, and got the gas filled; and the fridge is working fine now on the same day. This cost me nearly 4500rs, but I am happy that I have solved the problem. Till date, nobody has come to see my problem; and to my utter surprise, I received an SMS from Whirlpool that the customer is not willing to pay. Ha ha ha. My fridge is a double-door 280-liter fridge. What should I do?