Bought Whirlpool refrigerator (Model # WRF560SEHZ00) December 2018. After 2.5 years, the door hinge failed and could not be replaced. $1,000 for new door. Dont buy! Too bad there wasnt a 0 option for the rating.

I am very sorry I bought this machine. CU rated it pretty good. Nope. 1 - It rarely dries everything completely. e.g., the collars of t-shirts or turtleneck shirts are damp after the load is finished. I have to run the machine again....Energy efficient? Energy schmefficient. and I havent even TRIED to use the low heat delicate cycle. 2 - The cute modern buttons are hard to push in. 3 - The top of the machine doesnt have a level lid... Its curved. Not very useful for setting anything on while you work at any part of your laundering process.

We purchased a number of Whirlpool appliances (dishwasher, double door refrigerator, Duet stackable washer and dryer). After 14 months, the ice maker broke. $200 later, it was repaired with an upgraded kit.Last week, the washer error coded and the door locked so we could not get out the wet clothes. Called customer (no) service and they advised that we needed to call a service tech because he has a special tool to unlock the door. I stopped by our local appliance store and the counter person told me how to open the door. Had the tech come out for $70 and it could be the lock mechanism or the control panel. It turns out to be the control panel, which costs $250 + labor and would total to around $500, give or take a little. We are in our 60s, my wife does not take in laundry and the ice dispenser was seldom used because I can sneeze ice faster than this can dispense it so I open the freezer door to get my ice.The tech and the store clerk said that these were common problems with these machines. This was a major expense when purchased. So far, the dish washer has not had any problems, but tonight might be the night. The reason we bought Whirlpool is because of the Maytag connection, now that is in the same toilet.

I bought the stackable Whirlpool Duet. Piece of garbage (model # WFW9150WW). From day one the washer never worked. Error lights/bells kept going on before the second spin cycle. First repair guy couldnt figure it out. And the manual says just unplug and plug the power cable back in. Sure--every time I use it? I called Whirlpool service and they said a new control board was needed without even seeing the machine, which tells me this is a manufacturing flaw. I waited 2 months for the board. When it came, the repair guy put it in and then the machine would not stop filling. So another switch and hose are being ordered. Whirlpool customer service is completely useless. And no one will even discuss replacement. Now Im stuck. $700 out on the first machine and $200 on the extended warranty, which will be useless because Im going to dump the machine. And additional $800 on another new machine which probably wont work either. Oh, yeah, and you have to use special soap, which Ive tried, and got down to using only 1/2 a teaspoon because the suds never cleared. Please tell all your customers never to buy Whirlpool!

My oven had been temperamental since day one, then got worse over time. I do not use my oven that much so was not really worried or alarmed until a tray of cookies caught fire. It was set at 350 and jumped to 525 on its own. (I bought an oven thermometer to monitor) Minor burn taking tray out but all okay :-). Contacted Lowe’s where we bought it and they would do nothing (note: at this point the oven is 15-months old and out of warranty). Advised me to contact Whirlpool. Did that - they sent out a repair service and they determined it was the temp. sensor. It is now April 2014 and I am still waiting for the part (this all started Sept 2013). I have since talked and wrote to Whirlpool for this to be resolved and also asked that the range be recalled due to fire hazard at the least! When I spoke to them in December, they said they could give me ‘50% off the part’. Remember I am still waiting for that part, lol! After writing corp h/q, they said “Sorry, since we cant get the part why not have someone come in and take the old part out and have it rebuilt.” I ask you Whirlpool w/q would you be happy with that??? Will post any follow-ups... would love to hear from anyone else with this problem - model # GFE461LVS. Great day everyone. :-)

Our home is only 8 years old. Our neighbors and double ovens have all gone out! I mean it just quit working and the parts and repairs are crazy expensive! We have already spent $400 on a control board and now we need a control panel which is another $300! Its ridiculous spending $700 on repair of an oven that should have lasted a lot longer! Another thing is that our ovens are white and now the panels only come in black! I will never ever buy Whirlpool appliances again and I am spreading the word to everyone I know!

I purchased this microwave in September 2010. It was installed in a vacation home, so it has actually been used for less than one year. It has now stopped heating food for the fourth time. The previous problems miraculously fixed themselves after flipping the fuse for a few minutes. I guess I should have been suspicious at that point, but I figured maybe I had overheated something. But this time, the problem has not corrected itself. The Whirlpool representative that I spoke to, while very polite and personable, only scheduled a service call that will cost me $89.95 PLUS parts and labor. I asked her if other people had reported this same problem, since it had happened to me several times. She told me NO. I decided to do some research myself (yes, I know; I should have done this BEFORE I spent $578 on a worthless product) and found that many others have had the same problem, and that this is obviously a defect in the design of this unit. Unfortunately, I purchased the entire Whirlpool package because of a special rebate available at the time. Now, I am wondering if my other appliances will begin to break down in the near future. After reading about the experiences of others, I am calling to cancel the service visit. I will be removing the microwave from my kitchen and purchasing a new one. Whirlpool has lost a customer. I will NEVER purchase a Whirlpool product again.

Bought the Whirlpool Cabrio washer (WTW7300DW) and dryer (WED7300DW1) about 8 months ago. The washer always leaves white debris on the dark clothes - looks like detergent. Except I use blue liquid detergent. It seems like the inside, bottom of the drum is deteriorating and sticking to the clothes, since there is nothing that is white in the washer. I have run it through the clean cycle several times with the recommended washer cleaning product (the brand that came as a sample with the washer). That did not help. Also, we have a dog, our old washer used to rinse out a lot of dog hair from the bottom of our socks, etc. My filter for my drain hose would always have dog hair in it. With this washer, there is no dog hair being rinsed out at all. Lint and dog hair is all through the clothes after the cycle is over. Makes me wonder where the dirt is going, then.The clothes are so twisted after washing. Anything with long sleeves get tied up around other clothes. This seems very rough to wash clothes this way. Also, if you dont use the deep water setting, its likely not to get parts of the clothes even wet. I had a gray hooded sweatshirt go through a whole wash cycle and there were spots all over it that never even got wet at all. The dryer power button is very temperamental. Sometimes I have to hit it 6 - 7 times, at different angles, until I hit it just right to get it to turn on. Other times it just turns right on. There are just 2 of us so I only do 10 - 12 loads of clothes a month. After reading all the awful reviews, I fear that these problems, which are becoming evident now, will only get worse. Yet I only have 4 more months until the warranty runs out.

Purchased a Whirlpool range. Shopped around for several weeks before I found what I thought was a good price and with a rebate! Ive owned the stove for 2 months and 7 days... guess what? The stove broke. The burners popped. I called to have it serviced and remember that it had a rebate. I never received any paperwork on the rebate but figured its Whirlpool, good company. Wrong... its not that I didnt have the rebate paperwork but the rebate has expired... even though I didnt get any paperwork nor was there any mentioned of a time frame. Dont get me wrong if it had been 1 year or even 6 months... really 2 months!!! So not only did I not get the rebate of $100.00 I have a broken stove! So tired of being ripped off!

We purchased our Consumer Reports rated #1 best washer, seven yrs. ago with a five-yr warranty. We have had nothing but repair after repair starting in the first year. The mother board replaced twice, the entire inside had been replaced within four years. It is only a household of three, the washer looks like new! The machine is now making a noise like a freight train... We had a repairman out $95.00 just to look at it! Cost of repair $1,116.21!!!! More than what the machine is worth. The replacement parts wore out in the last 2.5 yrs, again poor design. I contacted Whirlpool during the last repair issue and demanded a full replacement. The customer service rep, as RUDE as can be, checked with her higher-ups and said they would replace it for $845.00!!! WHAT A JOKE. I could buy a new one for that! The repair person said they are one of the highest repair units and the most costly out of warranty. He had one with the same issue just two days prior. I will never buy another Whirlpool product or purchase from H&H Gregg. They sold our warranty twice losing all of our repair records! It looks like I had an extra load size dumped on me!

Fridge: no ice cubes. Water dripping from the door. Base of one door damaged. After 4 WHIRLPOOL repair services visits, ice cubes OK. Dishwasher: 40% of the time, kitchen floor damped with dirty smelly sticky water. Were first told: Its the product; next: Its the way you arrange dishes; next: The filter is not completely clean. And we are waiting on the 4th visit from the Whirlpool service. We have owned at least 7 dishwashers so far, this is just unbelievable! Poor poor poor performance, with dishes covered with dirty film once in a while. And you never know when the dishwasher will decide to misbehave...Stove: White ceramic stove one day broke with a sauce pan cooking on top of it... Microwave and stove and oven: they beep and beep and beep, to tell you you are increasing the heat (one beep every time you touch), to remind you infinitely the food is ready, etc. And there is NO way these contacts can be disconnected. Now imagine oven on plus 2 saucepans cooking on the stove for which you have to increase/decrease temp. plus the dishwasher finishing, all at once, every day. How much beeping it makes after a long day at work.

Whirlpool Cabrio washer - Its been a month now and still the washer is not fixed. The repairman through Lowes warranty service is the worst by far I have ever dealt with. I had new transmission put on, still wont agitate and smells hot. The washer is only 18 months old, well taken care of. This expensive hunk of junk is worthless and the aggravation for all this mess is worse. I called Whirlpool 2 times. The first time, I got a call with the standard oh so sorry bit. Oh boy, that gets the washer fixed. Not. I blasted them and Lowes again. I have had it with this mess. The repairman is supposed to contact Lowes a week ago for replacement. He has done zero. I called Lowes to check. How can they sell this junk to customers who pay for this washer? They know it is junk, Lowes and Whirlpool, so do the right thing and recall the junker for refunds to consumers.

We had purchased matching Whirlpool Cabrio HE washer and gas dryer. Both appliances were worthless. Same problems as everyone else. Clothes did not come clean. Had to put it on bulky items just to clean the clothes due to lack of water. Funny how all the older machines that actually put water into the machine cleaned clothes. Went through a motherboard (computer) for both the washer and dryer at $250 each. Washer had repairman out at least 12 times over 3 years. Never again would I purchase a Whirlpool. We went to our local appliance dealer and purchased a Speed Queen. These are like the older ones. THEY WORK! They use the correct amount of water and wash your clothes in half the time. 22 minutes per load! You can open the lid while the water is running in and load your clothes. Gee, what a concept. Only company still making them in Wisconsin, United States. Go Wisconsin! They back their product with a 20 year warranty. What?? Who does that anymore? Companies who stand behind their product. We love our new Speed Queen.

This Whirlpool Cabrio washing machine just does not do the job. It smells inside and does not get clothes clean, just normal everyday laundry. I usually have to put them through twice. It is supposed to be a water save, but I dont think it uses enough. I use minimal he detergent, yet you can see detergent residue on the clothes after they are washed, I think because there is not enough water running through to rinse clothes very well.

I have a 5yr warranty. Im 3yrs in on the 3rd repair. Horrible. This time they cant get the part and Ive been dealing with them for 5 almost 6 months. I spend countless hours on hold trying to get a real person... When I do they send me to someone else where the queue starts over. I paid $400 extra to just have them replace the fridge and its been over a month and they cant even get a new one delivered. Just refund my money! This is beyond the pale. Dale, Sunrise Beach Mo.

We bought Whirlpool Frontloader Washing Machine not over 1 month ago and it started to malfunction showing Ed1 error on its display. We contacted the service center and it was taking too long to have a visit from a technician. Then the technician, who also installed the unit came and checked the unit. He called someone from corporate office or from support team to ask what is error code Ed1 and overheard over the phone that this is a known issue on the brand. The technician said it is possible that unit will be replaced or only the motor. I contacted the brand support thru Messenger and requested to have the unit replaced, because again, the unit is not over 1mo old.I was advised it is not possible as replacement of unit is only applicable when the issue happened within seven days of delivery. STUPID ISNT? Policy is something unworthy for a product that is over 30k. And again, unit started to malfunction not over a month after it was first used. I would say we pretty much took care of the unit, we only use it twice a week. Placed it where it was perfect to put. Followed every advice given to us by the technician who installed it but still, it malfunctioned a few weeks after we started to use it. I am ashamed of the brand itself, we should have chosen Panasonic or Samsung instead not a dumb brand like Whirlpool. I certainly do not recommend the brand for a washing machine unit. Frontloader is a crap.

Avoid Whirlpool refrigerators and dishwashers. Fridge sounds like someone’s trying to get out. Repair person said it’s icemaker and typical. Dishwasher has little friction gaskets that keeps the door from falling open. They’ve been replaced twice and found one on floor today. Plastic end of slider for upper shelf keeps falling off repairman replaced it showed me how to put it back on. This falls off regularly. Range has coils underliner of oven. Takes forever to preheat and self cleaner cycle is a joke. Million dollar condo with upgraded crap appliances.

Whirlpool Duet Washing Machine model WFW9150WW02 - This machine was purchased new in Sept. 2011 along with a brand new dryer. We started noticing a rumbling sound within the first year, but both machines did a fantastic job on the laundry. Then last week, the washing machine didnt spin out a load of laundry. We called the company and they scheduled a service visit through A&E Factory Service. The technician immediately diagnosed the problem as a bad bearing and said that he had seen the problem frequently with this model and put it down to a design defect. The bearing is housed in a stainless sheath protected by a rubber seal, but the seal lets water in, which rusts the bearing. The cost to repair it was over $700. He suggested I call WP and ask for a concession, whereby the company would at least pick up all or part of the cost of parts. The service representative summarily dismissed the request, saying the company had no obligation to stand behind the product as the machine was out of warranty. I said that this was unacceptable. She was pleasant, but kept asking questions and putting me on hold. Ultimately, she said the same thing. Whirlpool was once a dependable name, no more.

When I bought this stove, I already had a glass top (Sears) which was satisfactory but I changed to get a convection oven, never had a problem cleaning the glass top. To me, Whirlpool was, and I emphasize WAS, a reputable manufacturer and the stove offered everything I needed. Not so, the glass top is a nightmare to clean; no amount of elbow grease works. It is like cooking on a mirror. Talked to everyone I contacted but, it seems, I am the faulty element in this problem: I DONT KNOW HOW TO CLEAN!!! YOU NEED A FIRST OF SOMETHING FROM TIME TO TIME AND THIS WAS A FIRST FOR ME.They told me the only solution they could offer was to buy their own cleaner. Why do they need to market their own cleaner? I did not buy a museum piece that needed to be treated with special care, I bought a stove to cook on. I want as many people as possible to know about that uncleanable glass top. Every time I need to cook, I cringe at the amount of time and effort I will have to spend to get it clean. I am not a novice, I have been doing housework for the past 60 years. Beware, it is a most frustrating situation to having paid top dollars and to be stuck with a product that brings such frustrations. By the way, it was bought at The Brick in Canada. They were not helpful either.

I have a Whirlpool cabrio washer (Model: wtw6300 Serial Number: CT3573525) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. At the beginning, I didnt care because I had warranty with BrandsMart. I had to call at least four times. But now, I bought the automatic control and it didnt work. For two days, I was trying to balance this machine but it is impossible since the beginning.I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool. Two of the gas burners of my Whirlpool kitchen, after two years of use, are no longer working. I will definitely contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

My refrigerator is 6 months old and already has rust and leaks. I am told it is because I live too close to the beach. Do not buy their sub-par products which come along with absolutely awful customer service. Will never purchase anything Whirlpool again.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

WRX986SIHV00 - French Door Fridge, cost $3k. After 16 months lights on top of fridge and freezer broke, Whirlpool only states no more warranty and offers no help. For such a pricey appliance that is a very weak quality and inadequate service IMO.

I purchased a 50 gallon Whirlpool water heater, model FG1J5040T3, in November, 2005, and have had the same experience as reported by the hundreds of others, whose comments I have been reading. Basically, pilot wont stay lit. I called Whirlpool, relight the heater, when it doesnt relight, wait to receive repair parts, call a plumber, and pay to have them install it, then repeat same problems. Each time going for a week or so, without hot water.After relighting the heater 10 times in the past year, and service calls, Whirlpool authorized me yesterday to return it to Lowes, and get a replacement. I need to hire a plumber to unhook it, haul it to Lowes, get the new one, and install it. It cost me about $300 to $400. Will the replacement be any better? I am considering just replacing the heater with one made by Rheem.

Whirlpool Electric Convection Range - We purchased a Whirlpool fridge, range and microwave, I am finally sending my review after another of many frustrations with the AquaLift self cleaning oven. NEVER, NEVER buy one unless you love cleaning your oven. The temperature goes to 160 for 40 minutes, it does nothing to clean your oven. I called the co. we bought it from. The fellow said, Oh you should clean your oven weekly, really there are 2 of us and I use the oven maybe 2-3 times a week without spillovers. When I do have spillovers I use the AquaLift waste of time, then have to spray it down with Affresh Spray the co. I bought the range from recommended, still have to scrub hard to remove built on spills. Save yourself the money and frustration. Buy anything but a range with AquaLift self cleaning.

I have a Whirlpool top-loading washing machine model 3LA5580XSW3. The timer switch is not working and I have been told that spares are not available. Is this true? Everything else works well. Please advise as I really need a new timer.

Absolute junk. Bought an entire matching set 2 years ago. Fridge, microwave, dishwasher and oven. Oven is the most user unfriendly thing I have ever bought. That’s my fault. Microwave failed. 300 to replace. Ice maker in side by side fridge failed, another 300 dollar fix. I used to have a field mouse or two get into the house every year. Don’t have that problem anymore because the fridge is so loud it scares them off. Talking to Customer service was the most frustrating thing of all. They think if they say your name in a nice soft tone long enough it will make everything ok. Mother and father raved about Whirlpool products. How times have changed. Do yourself a favor and steer clear of these products. Also, look up the other brand names made in the same factory and steer clear of those as well. I used to think appliances were all the same. How wrong I was. Do your research. It will save you a bundle in the long run.

Ran Aqualift self cleaning cycle 4 times at 40 minutes and only bottom was cleaned, sides are still spotted and the rear wall still shows a heavy spotting. My stove is less than a year old. My prior stove with self clean at a higher heat was great, when done only had to wipe out!

This dishwasher, compared to my old one, is very quiet but does a very poor job of cleaning. I now have to prerinse most all items. The silverware rack leaves many dirty items such as peanut butter off a knife. I probably waste more water on prerinse than what is saved by the washer.

I purchased this washer (Whirlpool Cabrio Model #WTW8000DW) 10-25-17 from Best Buy & now it has no power to the panel at all. The power to the outlet is fine which I can plug a hair dryer in & the hair dryer works. Tried all the reset buttons & options with nothing on the panel working as well as unplugging. Still nothing. It is barely 4 months old & I am very dissatisfied for the amount of money I paid for a high efficiency top loading washer.

Same problem a lot of people have written about in your forum. Purchased a double door stainless steel refrigerator, bottom freezer, # GX2SHBXVY from Sears Canada on 12/17/2011. Warranty expired December 2012. Now we have ice forming on the floor under the bottom freezer though water hasnt seeped out as we are now cleaning it daily. Sears wants to charge $75 per hour + parts as there is no extended warranty. Whirlpool says its a common problem with most other Competitor models too. REALLY, ITS NOT. Have checked with a lot of friends of mine with similar models. Nobody is having a problem with especially units hardly one and a half years old. My bro-in-law also bought a Whirlpool a year prior to mine. He is having no problems. See no reason to spend $300-$400 on a comparatively new unit. Also have a 7-month-old stainless steel Whirlpool dishwasher and 4-year-old Gold Accura cooking range. Now spend morning and nights looking at them wondering when they are gonna blow. Need to replace my washer/dryer too but guess which brand I am not opting for.

I purchased a new Whirlpool Cabrio yesterday. When I went to use my new washing machine it did not work. So basically I have a brand-new washing machine that is a lemon. I will highly recommend do not buy any Whirlpool products.

I Purchased 9 year warranty, Whirlpool water heater and installed it. Started having problems in the first month. It started giving a water temp too high error code, yet water was barely warm. Called Whirlpool. They had me do a bunch of diagnostic checks. Determined it was a bad control module. Sent me a new one. I installed it. Within a week or two, same problem. Called Whirlpool. This time they sent a Tech out. Everything on water heater tested normal, nothing wrong with any part. The tech finally, found a TSB that indicated that you couldnt have any re-circulating valves or systems connected to the water heater. We had one to keep hot water at the taps. So I removed the re-circulating kit and water heater worked for a few months. Then same problems, it keeps going into error. Error code indicates water temp too high, but water is barely warm to cold. Call whirlpool several times, they send out another control module and heating elements and I replace them. All work temporarily. Finally replace control module again, and it works for several months. Then back to error codes. Not always the same code. Sometimes it is water temp too high, other times it is check one of the heating elements. We have lived with it like that for about 3 years. We get hot water by resetting the water heater several times a day. Well, about 3 months ago it started tripping the circuit breaker in the electrical panel. I called Whirlpool and explained what has been going on since I bought their piece of junk. They will not do anything unless I call and pay for a service tech to come diagnose and repair the problem. They will provide the parts for the repair. I am not a certified appliance repairman, but I do handy man repair work for a living and do appliance repairs quite regularly. I am capable of doing every test that the repairman will do, but Whirlpool insists that I pay to get their defective product repaired. Then if I have problems again in a couple of months, I will have to pay a service tech again. I have friend that had this same water heater. I replaced the control module on his once. I was telling him about my woes and he told me he got fed up with all the problems and ate the cost and got a new water heater, not a Whirlpool. I am going to call Whirlpool one more time and then I am sure I am going to do what my friend did and put the money I would spend on a service tech into a new water heater. It will not be a Whirlfool.

I have had no trouble with this ref. There is absolutely nothing bad I can say about it. Once or twice something has fallen behind the drawers/ranks in the freezer.

I wish I had purchased this a week before I decided to become an owner of a portable AC unit. This unit cools my 390sq ft living room with ease, paired with a large 3 speed stand-alone fan, the adjacent rooms feel the coolness as well. I plan on purchasing another uni, with a lower SQ rating as to have for the master bedroom. Easy to install, move and drain when the time calls for it. Not too loud, not too big, not ugly and I would purchase this unit again.

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

I have a cabrio washer which is the worst washing machine I have ever seen. I can wash a small load of clothes and the ones on the bottom dont even get wet after being in the machine for 60 minutes. I have tried setting it to heavy loads, added water, stopped the machine and redistributed the clothes, it was a total waste of money. Dark colors come out looking worse than when they went in. If I save money on water I spend twice as much on electricity because I have to wash everything twice. The store where I bought it went out of business so I have no recourse.

Purchased Whirlpool fridge in December of 2013. I have had repairmen at my home over 10 times for repairs after warranty expired in December of 2014. Purchased extended warranty and still have to wait over a week for repairs through local Whirlpool service tech. Ice maker has been problematic from the start. Either it makes a bucket in 3 days time or it makes none. I will not buy another.

I bought this washer less than 2 months ago and I am devastated to say the least as they are not even remotely cheap. Appears that is doesnt come close to using enough water or enough agitation to get even 2 pieces of clothing clean. What good is 5.8cu (largest size tub) if you cant even wash a load sized for non HE washer. I am forced to wash a 1/4 of the amount of clothing now vs my previous standard washer, if I even want half cleaned clothing. I have tried every cycle with no difference.Doesnt use enough water but appears to spend most of the cycle time, filling with water. I know that sounds contradictory, but there isnt really any other way to explain it. Might as well not even have an (agitator), I use that word lightly here, as it does nothing to help clean the clothing inside. Pre-programmed cycles are not enough to do what you need it to do. Because of the pre-programmed cycles, unable to place clothing inside, fill with water, agitate a little and then stop or pause long enough to let contents soak for a while. I really miss being able to do this with my previous Whirlpool washer.It doesnt matter how little or how much detergent you use, the results are always the same, clothing comes out partially dry and dirty. Usually requires 2 or more wash cycles to remotely obtain clean items. Most items never even go under the water, no matter how much water it decides to fill with. I am so disappointed with Whirlpool with this fiasco they call a washer, with their name on it and they should be also. I have never owned any other brand than Whirlpool, so I didnt hesitate to buy this set, as I had wanted them for several years and finally made the decision to purchase and what a mistake this was. Will never make this mistake again. Whirlpool needs to correct this for every customer that has purchased these washers or risk ruining their reputation.

We purchased our Whirlpool Duet model WFW9150WW01 13 months ago. The warranty was up at the one year mark. We chose not to purchase the extended service plan. After all, a washer should last at least five years right? Wrong! The front seal has gone bad. It is an $85 part plus shipping, plus hours of my time. So, I purchased a product that is supposed to conserve water and instead I am having to purchase a petroleum-based product (the rubber seal), as it would seem, every year or so! These companies have us snowed with the whole conservation bull! CFLs, High Effeciency, Bio Fuels, etc., its all a hoax! And it is a hoax at our expense. Does anyone just produce a good product anymore? Oh yeah, I forgot... Japan does! Our economy continues to go to hell while other countries are coming online. Get your act together, guys, before we lose everything!

We purchased a new home April 2013. All our appliances were new Whirlpool stainless. Looked nice. After almost a year our microwave started acting improperly. Beeping, changing screens, not working when buttons pushed. Then the micro wave had a melt down and caused the glass try to break, parts to melt and caught fire internally melting plastic. Notified Whirlpool and they sent out individuals to repair. After several weeks the repair was completed and we were advised that they did not understand why this would or could happen. We should be fine now. Well we are now again having this unit beeping, changing screens, not working when tried, and when entering numbers, number and time are not what was trying to be entered. This unit my wife says is possessed and she wont use it. She fears it will burn the house down. It is Velos model TR 2 24 11000 serial number. It now beeps and changes with door open as I read the serial number.

Purchased a Whirlpool Cabrio washer with the glass lid. This is not a good washer to buy! The clothes do not get clean. Have to set it to bulk to get enough water to even cover clothes. Biggest issue is the lid. I have had to order a new one as it cracked on both sides back by control panel. I took the old lid off and discovered why the lid cracked. I have read many complaints about this same issue and everyone said Whirlpool would do nothing about it or even acknowledge there was a problem.Here is the problem. On each side there is a spring to hold the lid up while in the open position. The lid is plastic. When I tried to push those lid pins down with the lid off they would not go down. The springs are too strong for the plastic. When the lid is down the springs are trying to hold the lid up, so they are pushing against the plastic. Given time the springs win out against the plastic and the lid cracks and breaks. I am just a simple housewife and I figured this out! I hope that every manufacturer that is making glass top lids STOPS making them out of plastic, uses metal instead, uses a spring that is not as strong, or foregoes the current design and comes up with something that is better. It is for certain that I will never buy another Whirlpool appliance!

I purchased a Gas Stove from Home Depot on 11/23 and it was delivered on December 3rd. My God, Im having a dinner party tonight and the stove doesnt heat up past 170.. Unbelievable!! Need a replacement gas range. Tried to chat and call Whirlpool unsuccessfully. I am very one disappointed customer right now!

I purchased dishwasher model #GU2800XTVT0 in May of 2009. Today, it leaked water all over and damaged my floor. My husband pulled the dishwasher out of the cabinet and found that the motor had fallen off. It did not have a bracket to hold it in place and worked loose, which then disconnected a hose. I called the customer service but they wont do anything because it is beyond the 12 month warranty. It only lasted slightly more than two years. This is obviously a manufacturing defect and we were just unlucky enough that it failed after the warranty had expired. The most ironic thing is that my husband worked for Whirlpool for 20 years. There is no loyalty here.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

Purchased a matching set, Whirlpool Cabrio Platinum Washing Machine and Dryer in November of 2012. After just over 2 years, Im stuck replacing the Washing Machine at my expense! The washing machine began leaking water out of the bottom of the unit and became extremely loud when operating it. The repair technician said it was a seal and bearing that needed replaced and the cost of repairing the unit would be cost prohibitive versus replacing the unit all together ($800+)! Originally paid over 2K to purchase these units and have them installed. I do not want to trust or rely on the Whirlpool brand again. I would appreciate any recommendation for a better quality, high capacity, HE washing machine brand to replace the Whirlpool unit with (Samsung, GE, LG)??

I purchased this Cabrio washing machine in December of 2016. I have had a huge amount of trouble with the soap not washing out along with it tangling my clothes. This has to be the worst machine I have ever purchased.

I purchased the Whirlpool Cabrio about five years ago. Last year, the motherboard had to be replaced. This year, it started load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $100 to have someone look at it, and was going to cost almost $400 to repair, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. Do I have Stupid tattooed on my forehead? I will never buy a Whirlpool again!!!

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

Purchased the Gold Series Dishwasher Model No: WDF730PAYM0 Serial No: F14403489 on Dec 2011, started using it from Jan 2012. All is good until June 2014. It started leaking from the bottom, called Whirlpool - the great bad company. Since it is not under warranty they asked to schedule an appointment with their local authorized rip off service company. Technician come on the service day and told me that it is $120.00 for the service call and Labor and parts are extra, first of all $120.00 to come to my house is first rip off, that is the reason Whirlpool on their website do not give any estimates on the service call.After checking the appliance he said main assembly is bad and needs to replace and that will cost more than the original purchase price - what a ripoff. He asked me to contact Whirlpool, they may help since this is the known issue with this model. Called Whirlpool and mentioned and they said it is too old to continue to operate so they cannot help. Ended up trashing the 2.5 year old dishwasher for the new GE dishwasher. Never buy a Whirlpool ever again even on sale. Whirlpool company is not ethical and not ready to help consumer, would love to see them close their operation in America.

This is our second Whirlpool refrigerator that has the same defrost water drainage problem. I was told this newer model had updated technology, not so, actually it is worse. My older refrigerator went about 8 years before I started noticing water on the floor and this newer model is 4 years old and it started having water overflow at 3 1/2 years. Then in April we replaced the water filter and the ice-maker stopped working. My freezer also stinks like stale water (my reason for replacing the old refrigerator plus the water on the floor). I followed a YouTube video for defrosting the drainpipe, it was very tedious, labor intensive, and time consuming and worked for 3 weeks. This is very upsetting. After spending $2500 to have such problems and my expensive $150 4-year extended warranty expired just weeks before the ice-maker went out. This is obviously a design problem that Whirlpool refuses to address since my other model was a year 2000 model and my 2013 has the exact same problem. VERY POOR customer care in addressing these design failures of both the defrost drainage (just make a larger drain port!!!) and the ice-maker.

Whirlpool Cabrio Platinum Washer - I have a 2 1/2 year old washer that has been serviced twice. This week 10/2/14 the service technician informed me that we had a bad tub bearing. The bearing failure caused a leak which corroded the rotor & stator. It was more cost effective to buy a new washer than to repair our unit!!!! Ive never heard of a washing machine needing to be totally replaced after 2 1/2 years. Any ideas how to deal with Whirlpool?

Whirlpool oven WOD93ECOA501 - This oven will most likely lock up if you use the clean cycle. I wish there was a class action suit in California. This happened first time I used the oven. Very expensive to fix, and though it was 9 months after a kitchen remodel, it was not under warranty because we bought it early and it sat in garage, and Whirlpool could only use purchase date. This is not new technology. Upper and lower oven both locked. Wish I had bought a Blue Star oven, as my Blue Star cook top is fantastic and a pleasure to use. HAS ANYONE GONE TO SMALL CLAIMS COURT?

The Cabrio is the absolute worst washer that Ive ever owned! No matter what combination of setting I use, my clothes come out dingy, all twisted and wrinkled, and full of lint and detergent residue (I use liquid detergent made specifically for HE washers). Every setting runs for over an hour. So much for high efficiency! What it saves on water it more than wastes on electricity!! More often than not, the entire load becomes enveloped in one of the items to create one huge ball. A t-shirt stretched to encompass the remaining clothes into a perfect sphere! When that happens, some of the laundry in the middle of the big ball is barely damp. The dryer is just as bad, even the towels come out wrinkled. How is that possible? And again, it takes over an hour to dry a load.Whirlpool customer service is awful. When I called to complain, the agent began schooling me on how to wash clothes. Im 66 years old, Ive washed a few clothes in my lifetime and have always prided myself in my white whites and bright colors. I have a new house and the builder provided all the appliances. Based on my past negative experience with Whirlpool products and their customer service, I would not have purchased Whirlpool.

Broken drip pan was cracked, replaced, and wood floor damaged, also replaced. Compressor replaced. Ice warmer replaced. Hinge on crisper door broken, replaced. Freezer door handle keeps falling off. All this in first year. Builder purchased 1 year Extended Warranty. Freezer ices up occasionally. Repairman advised using a hair dryer to free up the rails. All this on a $2,000.00 Whirlpool Refrigerator. Do yourself a favor and dont purchase this Refrigerator. Model #G16FDRXXY.

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

I have clothes that are coming out torn with large holes, especially cotton items. I dont know if it is the washer or dryer.

Whirlpool Cabrio Washing Machine F1 code - We have had this washing machine for over 6 years now, and ever since our 3 year warranty time was up, the washing machine will only stop, and display the F1 code as soon as the wash cycle has completed, with 23 minutes left. To start off, with this problem, it is causing me more water, and electricity that should not have to be wasted if the machine worked properly. I called the place where I got the machine, and was told to give Whirlpool a call. I did this, and was told that there was nothing that could be done, and if I would like to schedule an appointment for a tech to come out and work on it, they could do that. YES, I would have to pay for it. Needless to say, the washer has been doing this for over 6 years, and if there is a way to get it fixed WITHOUT having to pay for the repairs, that would be wonderful.

We recently bought a Whirlpool front loader even though the reviews kept mentioning mold and odors. I discovered that there was a water buildup in the soap dispenser so after every load, I remove, clean and dry the soap dispenser. The machine does a great job on cleaning clothes and I am following other suggestions on cleaning the drum from time to time. By the way, I bought my machine at Lowes from the scratch and dent department and with a little negotiating, I paid half price! Good deal and so far, good machine. Good luck and remember to remove and empty the water from the soap dispenser!

My 2 year Jennaire (made by Whirlpool) broke down on 12/14/11. Repairman came out on 12/19. He said that the compressor was not working and ordered another and he came out again on 12/22. He said that it could not be fixed (internal leak or something). An aside to this story was that a tank of compressed oil blew and damaged my hallway and kitchen walls and floors and 2 rugs. That was being handled by the repairmans insurance company.We called Whirlpool and they said that they we could pick out a new refrigerator priced at no more than $2399 even though we paid $2799 for the Jennaire and would have to pay the difference for a model costing more. We went with a Maytag (Whirlpool product) that listed for $2899 but was available at 2 local stores for $2050 and $2100 but I had to give Whirlpool anther $500 because they use the MRP.They finally delivered it on 1/5/12 but would not leave it because no one disconnected the water line to the appliance and they would not touch it. It took me 20 seconds to do it and if they would have told me so it would have been done on the 5th. Rescheduled delivery for 1/8/12 and the unit was delivered damaged (large dent in front) and they would not temporarily leave it until a replacement came.I called Whirlpool again and asked them to just call a local Home Depot or anyone in my area (all had the unit in stock) to deliver one but they told me that it must come from the warehouse in Michigan (I live in PA) and that it would be yet another 5 to 10 business days to receive it. So, I am paying $700 more for a unit that I could have bought and had delivered before Christmas not to mention the inconvenience of no unit for a month. Not to mention the damage to my home, $200+ dollars in thrown away food, time to shop for new unit, time for 2 repairman appointments and time for the 2 deliveries thus far and countless phone calls to Whirlpool to get the new unit.Today is 1/10/12, so I guess Ill have by month end if there are no other problems, you would think that they would try to expedite this just because its been so long or give us a substantial credit for all the trouble. Never again Whirlpool.

We had to have a sensor switch installed. We purchased this washer, plus the matching dryer June 10, 2010. This was just 16 months ago today.The cost of this repair was $160.24, for part labor and service call. The service call was excellent. Wish I could say the same for washer.We had previously owned a KitchenAid washer for over 20 years (before purchasing Whirlpool washer) and did not have to have one repair on it. Very doubtful I will purchase another Whirlpool.Looks like quality is a thing of the past.

I purchased Whirlpool gas range with AquaLift Self Cleaning Tech exactly a year ago. DOES NOT WORK!!! The only Self that cleans will be you on your hands and knees. Still dont know what to use. Manual says do not use oven cleaner or abrasive or you void the warranty. Ok Whirlpool any suggestions? Soap and mild detergent not cutting it. You would think with all the customers complaining about this feature the bright engineers that designed this would come up with a solution.

I have a Whirlpool stove. Theres nothing but problems with the oven sensor. This is the 3rd time we have to replace it. It had problems ever since I bought and thats been 11 years ago. My Magic Chef lasted 13 years with no problems. I have a Whirlpool microwave that had a recall on it. Never buy Whirlpool!

The machine starts shaking uncontrollably, has to be paused and clothes redistributed but still shakes. The stabilizers were replaced approximately 1 year ago. This worked until today. I was was washing a small load and distributed the load accordingly. On the spin cycle, the washer again began shaking and I shut it off. I will never buy Whirlpool products again!

I have had this range since 2008 and used the self-clean last week. (I dont use the oven that often) Since the clean it has not heated up to required temp. I just called Whirlpool and a tech is coming out this Friday (Nov. 15th 2013). If it is determined to be the self-clean that did in fact cause this, the tech calls for an authorization and the repair is covered by Whirlpool. I will report back what happens.

It has needed a new motor, new tub assembly, and about six other repairs. Now the heavy duty tub just thumps around and I get an uneven load message, even when running empty. It is the worst single machine I have ever purchased, with the possible exception of the Whirlpool matching dryer, which lasted about three years.

I purchased a new Whirlpool Cabrio washer and it has been nothing but a headache. The machine constantly rips our clothes and stretches them beyond repair. Now, the washer keeps showing an F1 error code and I have to restart the machine three times to get it to start. It also stops in the middle of the cycle and I have to restart it. What a piece of garbage! I called Whirlpool several times and they do not stand behind their products. Do not buy Whirlpool. I filed a complaint with the Attorney General and I suggest anyone else having the same problems should do so. Maybe we can get this machine recalled.

High end Whirlpool dual front loader washing machine model number WFW94HEXW2 died after 5+ years of less than moderate use. Used no more than once a week. Paid for a top end model. Had 2 mechanics look at it. Mechanically it is fine. The CCU is not working correctly and wont allow it to start. We replaced it, but to no avail. It is barely out of warranty at 5+ years old. Called Whirlpool and they said they would do nothing. Asked for a manager and she was rude to add insult to injury. Cant get to the serial number because the door is locked shut as part of the shutdown problem. Cant find original receipt so including a picture of the credit card purchase. Trying to contact retailer but so far have not heard back from them.

Our Whirlpool refrigerator was delivered July 27th, 2013 after waiting 6 weeks for it. I was getting something off the top shelf (side by side refrigerator) when a 2-liter plastic bottle fell and put a hole in the bottom shelf where it sticks out under the vegetable tray. I have had grandkids sometimes stand on that shelf of our other refrigerators without ever doing any damage to it. It makes me nervous of dropping something else. I would like to send a complaint directly to Whirlpool but dont know how to reach them.

We bought a gas hot water heater from Lowes on Dec. 31, 2010. In July 2011, there was no hot water. After much yelling and headaches, Whirlpool agreed to send out a technician to look at it, since I refuse to go in the attic and I will not work on gas appliances. After 7 days with no hot water, they replaced a valve that failed, they said, because our attic was too hot. The old unit never complained. Eight months later out, the unit went again (and we had an attic fan put in). This time, Whirlpool sent out a local plumber (and I paid for the call) though we had a warranty and extended plan with Lowes?! This time I was told no problem it was too windy and it blew out the pilot. Its funny we never noticed the attic being windy even during the hurricanes. Four to 5 months later, well, you guessed it but this time my husband just re-lit it. Then the next time, 5 months later, my brother-in-law did it. That was August to September 2012. See, this morning, there is no hot water. I had to fight with Lowes since we have the 5-year extended plan. I cannot get anyone to explain why it makes sense to them that a 2 1/2 year old hot water heater has to be re-lit every 4-6 months. Then I went online. Now I know why Lowes and Whirlpool are ignoring the issue. So, anyone know a good lawyer or what are they doing to get satisfaction?

Bought expensive fridge 2009. Now (2015) random very loud rat-tat-tat sounds lasting 5-10 seconds. Very loud. Paid for repairman to evaluate. He said it was probably compressor spring and other springs would probably soon break and would shut down fridge. Said it is very expensive to repair and it would be best to dump the fridge and buy a new one. I called the 800 number located inside the fridge. Jacob at Whirlpool listened to my story and said, Yep, it sounds like the compressor spring and the other springs will likely break. He said he can make me a one-time offer of a full repair of the compressor for only $359.65. We pay Whirlpool and they will have a local guy here come and fix it. We paid by visa.And, via email we get a document that shows we just bought a service contract. This is a surprise to us as we were told were paying to have the compressor repaired. In a few days, a call comes from local repair shop. Guy says, he will come out and check out the noise and see if he can repair our unit. We tell him the noise is intermittent and we cant predict when the noise will occur. We also tell him Jacob from Whirlpool said it was the compressor and that we paid to have it repaired. He says it doesnt sound like it is the compressor and that he cant diagnose the problem if he cant hear the noise. We tell Maytag/Whirlpool via phone we are faxing formal request for refund of our $359.65. Lady from Whirlpool says we, should get a refund in 4-6 weeks. Well, we will see.We are very disappointed in the the short life of our very expensive fridge and we are disgusted with the false and misleading comments made by Jacob of Whirlpool. He told us we were paying for the repair of our compressor and instead we get a stupid service contract. We are in the process of buying a new fridge. And no... It will NOT be a Maytag/Whirlpool!

Our Whirlpool Cabrio washer is 2 years old and also sounds as if its a jet on the runway preparing for takeoff. The spin cycle started this about a month ago. It is so loud now. It is just SCARY. I am so angry! No recall??? seriously???!!! Rip-off. I will NEVER buy anything Whirlpool again!!!

My washing machine is just over a year old and it has ruined so many clothes... They come out with brown stains on them... Almost like a oily stain. Not sure where its coming from but its either Im gonna have to buy a different machine or keep buying clothes. My husbands t-shirts look terrible... If any suggestions to what it can be please respond back to me. Thanks. Model# wtw4815ewo. Serial# c51433710.

We purchased a new Cabrio top loading washer in June of 2011 to replace a Maytag Neptune (thinking at the time that wed gone as low as possible). We didnt abuse the machine. In fact, because it had a tempered glass lid (in a plastic frame), we were careful with the lid on the machine. It broke during a wash cycle. Because its heavy, the lid has spring supports on both sides; these are stronger than the plastic frame and over time the frame will break, rendering the machine inoperable. The discounted price for a new lid is over $200, and Maytag (I mean Whirlpool) tells us that it lasted through the 365 day warranty, so the bill is on us. It may be green when it works, but taking 18 month appliances to the landfill is not very green. And others on the web report say that the lid only lasts a year or so. The ratings scale needs to have negative values. Id give this appliance a -5.

My son purchased a Whirlpool washer and dryer as a Christmas gift on 12-24-10 from Sears. It didnt wash the clothes properly and I would have to rewash them. Also, it would not spin the cloths properly and the top would take forever to unlock. Then in July, I called for repair because the water would not spin out at all. It took at least two weeks for them to come out. Another two weeks to get the part they ordered then to find out that they also needed another part that was not diagnosed in the first place. After another three weeks had gone by and having to go to the laundry to wash our clothes several times, it was finally fixed. I continued to have problems with the clothes not getting cleaned. How can this possibly be an energy efficient product when you have to do the load twice? I am so grateful to my son for the gift but am so dissatisfied with the product. I rate this product 1 out of 5 stars.

Both are Whirlpool Commercial quality. I got them free from my Co-Op. They didnt cost me anything. They have been here for years - at least 18 years. They have performed flawlessly. I would look for anything discounted. I do not have a problem buying scratch and dent items or last years models. I am not big into brand names and their claims. My sister has gone thru several Maytag appliances in just a few short years. I will not buy any front loading washer, its top load only for me. The dryer has to be electric because we do not have gas in my Co-Op complex. I have been lucky to have only two washer and dryer combos since I was a kid. My family bought a Kenmore washer dryer combo in the 70s that lasted maintenance free into the 90s when I got the Whirlpool set that I have now. I only need the basics side by side set ups. Even though I live alone I do a lot of laundry. Since I have had these commercial grade machines I am more leaning toward another set of commercial grade machines. They seem to be able to take more abuse/over loading than the fancy expensive machines.

Love the dishwasher, except the racking which has some top rack channels which are too small to be used by glasses, mugs, etc. The Power On/Off should automatically power down when the cycle is finished. Too often when someone leans against the dishwasher while opening the overhead cupboard, the dishwasher will start up because the unit was not powered down.

We bought a Whirlpool cook stove with a black top in 2009 and this year, in 2011, while cooking a pot of stew, the stove top burner began to make loud popping sounds. When I went to check it out, there was smoke coming out from under the pan and pieces of glass that had exploded out in small chunks. When calling the customer service line at Whirlpool, they told us that it was no longer under warranty and could not be of help. Their only explanation was that they would only cover a new stove top if it had cracked or broken this way when putting a cold pot on a hot burner. They said their technician could tell if this was why the shards of glass were exploded from the burner.

I love my Whirlpool Washing machine. Purchased it 2 yrs ago & have not had any issues. Its quiet, large capacity. Washes my clothes very clean. The various washing cycles makes it so convenient to wash as much or as little as I need on any occasion. I do recommend to anyone that you do the cleaning cycle on these new washers to ensure top performance when washing.

I bought a 3 burner glass hob under your built-in cooktop category (model no. AKCG 930-90 cm) in Nov. 2015 from Coimbatore, Tamil Nadu. In the month of April 2015 I started having problems with the medium burner. The problems was rectified on 29-4-2017 after some replacements that cost me Rs. 5000. After two months again the same problem occurred, the medium burner was not igniting again, I registered a complaint on 5-7-2017, the representative came and did some maintenance and left but the same problem resurfaced after a few days.I was fed up of complaining and started using the burner during necessity by placing a weight on top of the knob. Finally on 15th Feb 2018 while I was using the stove the glass top cracked into pieces. My experience of the companys built-in cooktop is horrible and bitter. Every time I registered a complaint the representatives used to attend the complaint after 2 weeks and that too after so many phone calls. I am really dissatisfied with the service and quality of the product. I therefore strongly recommend customers not to buy this product.

It is a double oven. Temp varies too much. The oven is very inconsistent. Cooking Thanksgiving the temperature would not stay even. It took much longer than intended. It was quite frustrating. I would not recommend the Whirlpool double oven.

ED5PHEXNK00 Stainless Steel side by side Refrigerator bought in 2004, look out!The refrigerator caught fire today and there was smoke everywhere. Had I not been home, damage would have been out of control. I traced the smoke to the bottom of the refrigerator. I pulled the unit out from the wall and unplugged the power to the unit. My unit is out of warranty and past the extended Lowes warranty. The repair diagnosis is $100 to start.Whirlpool has recalled its other brands (Maytag, etc.) for this same problem but not its Whirlpool brand. Our problem is the same problem with hundreds of other people: Whirlpool fridges burning, smoking, and being a life threatening hazard to families all over America because of the faulty relay to compressor. Whirlpool better recall this model. They need to fix this or they will have much bigger issues to deal with (corporate manslaughter from a known issue and no action or protection for its consumers). The refrigerator is a result of Whirlpool’s negligence; thus, it’s potentially deadly.

We have a large family so when we needed a new refrigerator we found this very large unit (Whirlpool 32 cu). About this unit, its not really all that wide, but it is very deep. Lowes didnt have a model on the floor but we went by photos. Also the salesman showed us a smaller version of this unit and we were impressed with the design. However unlike the unit we saw the shelves arent adjustable. They are preset. Also the ice maker on top is very small and makes ice very slowly. The freezer section ice maker is much larger. The main complaint I have with that is unless you push the tray all the way to the back ice can drop behind the tray and fall down causing the freezer door not to always close properly, leaving you with semi defrosted food. Whoever designed this refrigerator was an idiot. All issues are really related to design flaws. This is a very expensive refrigerator. I expected a great unit and got a piece of crap instead. Stay away from this model at all cost. It would be smarter to buy 2 refrigerators instead if you have the room. This model will give you nothing but a headache and grief.This is our story about our experience. This all took place within 1 year. We bought it at Lowes. They were wonderful when it came to taking care of us when it was within the stores’ warranty. They really tried to help us. Once their warranty ran out they put us in touch with our new repairmen. Lowes did tell us that one other man bought the same unit and he was up to refrigerator # 15. Like I said, this unit is crap. Our first unit was delivered with a huge dent in the door. They took it back (lucky for us we have 2 other refrigerators).Second unit arrived in store also badly dented. They didnt bother to deliver that unit. Third unit arrives at store but back area around motor all dented up. They order a 4th unit. This unit wasnt dented up so they delivered it. However doors were very off and wouldnt line up so it didnt close properly. A 5th unit was ordered and same issue with the doors. A 6th unit ordered and they called telling me that it was all dented up and needed to order a new unit. Our 7th unit arrived and in 3 days started making funny sounds. Dual ice makers stopped working and inside refrigerator is was very warm. Lowes ordered #8. This unit the freezer doors werent lining up so #9 was ordered. This time everything seemed to line up, no dents however by the third month it started making a funny sound. Dual ice makers stopped working. Warm inside the refrigerator section. Lowes sent out a repair man. He explained a design flaw was not enough insulation around the fan so it was icing up. That was replaced and it was working nicely for 4 months. Same issues with fan icing up, the noise and no ice. The repair man came out again and mentioned what was kind of a recall with the unit. The control panel in the back of the refrigerator was wrong and needed the correct one to be put in. That was done. He told us that we shouldnt have any more issues with it.Same thing again. Same symptoms, same results...we had to throw out hundreds of dollars worth of food. (I just put in an entire prime filet mignon I planned for a special dinner and had to throw it out. OUCH!) Awaiting for the repair man, again. He will be out in 5 more days. Im sure it will be a new issue, a new brand new fix and it will work for a few weeks to months and we will be calling him again.

The damper switch at the top of my water heater, one I purchased at Lowes stopped working. I talked to someone at the local store, and I was told I had to contain the manufacturer. I called the number on the front of my unit. The tech talked my husband through the restart process...not once, but on two separate occasions. We were told that because it was intermittent, something they decided Over the Phone, they could do nothing. They would neither send a replacement part nor a technician. By the time we had to call back two days later, restart was impossible. JUST to get the part, a specialty piece, we now have to pay for expedited shipping! And either install ourselves, or wait 5 days After Arrival (!!), to get the stupid thing fixed! If they had sent the part out originally when we asked, we wouldnt have to wait for hot water or pay anything for a warrantied piece! Its a racket. Stay away!!!

I had to purchase a new fridge quickly due to a power surge and this was the only one available with features I wanted. It is too small, but thats not the fridges fault. Has worked well and easy to clean. Simple white fridge that Id recommend. Not expensive and for the past year+ dependable.

Whirlpool makes a beautiful product that does not last. I bought model WRX988SIBM in April 2015. Two years later the compressor is bad and no warranty coverage. Do not buy this model. It does not carry the Whirlpool 2-5 year sealed refrigeration warranty. Its amazing that an appliance that retails over $3K only comes with a 1 year sealed refrigeration warranty when Whirlpool offers it on other models. Be sure you know what your warranty coverage is before you buy any Whirlpool product.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

In 2012 we purchased a Whirlpool Nu40T61-403 water heater from Lowes that I installed due to us not being able to afford a plumber. I have since become a plumber. This morning while attempting to shower I noticed that the water was lukewarm with the shower valve turned all the way to hot. I got dressed and inspected the heater. I began to diagnose the problem. Pilot was out and Gas control valve signal light was off. Lit the pilot and it appeared to be functioning normally. My first thought was the thermopile had failed but seeing the pilot stayed lit this proved to not be the case. I was extremely relieved at that point. Turned the temperature control knob to high and the burner kicked on. At first it appeared to be functioning fine. But within about 20 seconds I began to hear detonations within the sealed combustion chamber.

Purchased a Whirlpool french door refrigerator at Lowes less than two years ago. Last week the freezer compartment failed, out of the one-year warranty of course. The independent tech who came to service the machine told me of all the refrigerators he services Whirlpools are the closest to total junk and he would never recommend them. Wish I knew him before I bought this soon to be piece of trash. The CEO of Whirlpool, Jeff Fettig, received total compensation valued at $14.4 million in 2010, up about 15% from a year earlier, the appliance maker reported in a securities filing recently. Appears to me that Mr. Fettig is ripping off customers for his own gain, with his boards approval. Shame on all of them -- another example corporate rip offs that are plaguing our nation.

My Whirlpool stove works really well, and it is self cleaning. I have had my present oven/stove combo now for 5 years and had not had one single mishap at all. I am so confident that you will like it I am personally recommending it. It bakes beautifully and if there is a spill or overflow in the oven I just press a button & it cleans itself!

I purchased my Whirlpool Gold series french door refrigerator 3 years ago. I bought Whirlpool because it being an American company and a brand I thought I would be pleased with. Wrong! I have had nothing but problems with this refrigerator. Thank goodness I bought the extended warranty! Just a year old, my ice maker stopped working. Then, the refrigerator stopped cooling. Circuit boards were replaced, fan motors, etc. over $1500.00 in parts and labor and the entire summer to have it fixed. This past August, ice maker stopped working again. Then, stopped cooling. I am now at week 6 without a functioning refrigerator. While I am thankful I have an extended warranty, through the store that I purchased this refrigerator, I am not thrilled with the amount of time that has passed between each visit and the fact that it is the exact same parts that are once again being replaced. This refrigerator is a LEMON. Do not buy this brand.

Since purchasing original refrigerator 2 years ago I have multiple problems. Freezer was icing up to the point where drawers could not be opened, after numerous service calls, door was replaced which did not resolve problem. Refrigerator was replaced on warranty. Soon after light control circuit board had to be replaced. Next light control had to be recalibrated. Now, with the unit being approx. 1 yr old, rust spots are appearing on freezer door. Whirlpool rep advised this problem is not covered on warranty and would not provide any information as to what company contacts could be used to pursue the issue. Very upset and disappointed with product and customer service.

I have had an extremely frustrating experience with Whirlpool refrigerator WRT311. It broke after 6 months. So far it has been diagnosed twice with a faulty compressor and leaking coolant. Whirlpool will (seemingly) never replace an appliance--even if it makes no sense to keep trying to fix it. This is a $600 refrigerator! I cant imagine how much they have spent in repair costs. They simply send a service tech time after time, jerking the consumer around with no regard for what we have to go through to arrange 6 tech visits, some of them multiple hours long. Yes, we have had six tech visits, for a total of 10+ hours, and six weeks living with a broken refrigerator. As well as 30+ phone calls, hours on hold, etc.The refrigerator is loudly throbbing away after being refilled with coolant twice, and is still leaking coolant. Are they hoping the customer just gives up and buys a new appliance on their own? I wonder about the many positive reviews of their appliances: Are they fake? Are they churned out by Whirlpool? I have no confidence in this company. They are inept, if not crooked, and I would advise buyers to beware of poor quality and extremely poor warranty and consumer service.

I have previously owned a Maytag washer for 16 years that went through three children. They are older now and two years ago I decided to buy a Whirlpool Cabrio for the upgrade and large capacity. Well just like every other customer that purchased these crappy machine, I now own one of the worst washers in the history of washing machines. It started about 13 months after I bought it and now is completely broken. I am so angry that I spent the amount of money I did to be so disappointed. I have not abused this washer and I can hardly believe the customer service or lack there of, that this company supports. I would hope that people do their research before ever purchasing a whirlpool anything. TERRIBLE COMPANY and my Cabrio is heading to the landfill.... Thanks Whirlpool. YOU SUCK!

The company I work for bought a new washing machine a couple of months ago to make it easier for those that do the laundry here. The washer was suppose to be this great washing machine which has turned out to be the biggest piece of trash on the property!! Every couple of loads you have to turn it off and hopefully the computer in this Whirlpool cabriolet will reset so you can wash a load of clothes. You have a 50/50 chance it will work. DO NOT PURCHASE THIS MACHINE. IT IS THE WORST WASHING MACHINE IVE EVER USED!!

The washer began to start making noises as if coins were in it or plastic breaking every time I wash. Also, it does not wring clothes out good and clean well. I have Whirlpool Cabrio.

I bought a Whirlpool gas range in March of 2015. Three months later the control module went out on it. It was still covered under warranty through Whirlpool, so they send a technician out to fix it. Its now a little over a year later and the control module is out again. I call Whirlpool and ask them if it was still under warranty and if they can it fix it so they say, you want me to send a technician out. Why? I just assumed since theyre sending a technician out but there were going to cover it. Well the technician gets here and its not covered under warranty. And I now I have to pay a $90 service charge fee for the guy to tell me that the control modules out on it which I already knew. Hes going to charge me more than the stove was worth to fix it so I declined to get it fixed.

Need to arrange shelves for better storage!!! Ive not had any major problems with it so far!!! I need the rubber seals on the freezer and refrigerator door replaced!!! Other than that its alright!!! Im hoping it lasts for a long time!!!! On disability and be hard to replace!!!

Very pleased with my Whirlpool dishwasher. It is not the top of the line but does a great job of cleaning my dishes and is very quiet when running. Whirlpool appliances have been very good to me.