Whirlpool Cabrio Washer and Dryer - I have had all of the problems that all of the other 900 people have complained about! The washer does not wash anything properly. I have even experienced having something such as a bit of cereal stuck to a dishcloth and it was still on there after a full wash cycle. All of my whites are now grey and stained. All of the sheets end up with a huge dirty ring the size of the tub in the middle of them. Everything comes out in a tangled mess of knots! Very frustrating! Everything comes out smelly as if its been sitting in the washer for days. Nothing smells fresh and clean like it should. Energy wise, we are using two and three times the amount of energy as I am washing and drying things for two or three times over, which brings me to the dryer. I put one single load in and it takes two or three cycles to dry it properly. This is unacceptable and I cannot believe that we cannot get some satisfaction from someone in this regard! We bought our set from Sears and I feel that they obviously know of this problem and still continue to sell Whirlpool products! Weve all been taken for a ride and Whirlpool should be held accountable for ripping people off this way. Someone please help!

We bought our washer in on 2011. Within a few months, the washers behind the screws on the top began to rust. Now less than two years after purchasing this high efficiency and expensive washer, not only are all the washers rusted on the plastic lid but behind the the lid and the side of the washer is rusted. Very disappointed and recommend that you do not purchase this machine.

My wife dropped a liter of pop 12 inches and broke the plastic shelf on pantry door. When I called Whirlpool, I was told its under use and abuse and they wont pay for the repair. It is an electronic component because of the pantry door. I asked to speak with a supervisor who would only apologize... I asked for the phone number to Corporate and was told there is no number, no email, just a street address to send a letter. How 1950s of them. Owned fridge for 4 months paid for the extended warranty and now I can pay $200 plus or look at a cracked shelf.

We have a Whirlpool Refrigerator, Model # ED5HHEXTQ00. And every shelf has cracked, the water and ice dispensing levers have broken off. Now our produce trays are broken as well. I do not recommend Whirlpool products to anyone. They will not stand behind their product! There is obviously a problem with the plastic used on the shelves and trays. I have read of others complaining of the same issues!Whirlpool! You need to step up to the plate and recall these shelves, and replace them for your customers!

I purchased a side by side Whirlpool refrigerator in December 2009. In one year’s time, all of the plastic shelving has completely broken. The repair man said that he felt like the plastic was substandard and to call Whirlpool but they said that we must have abused the shelving.I and my husband are senior citizens and the only ones using this refrigerator. How can all the plastic components break within one year? I had my last refrigerator for over 10 years and I gave it to my son. It is still running and all the plastic shelving is still intact.I feel Whirlpool should fix this problem but they do not care about their customers. Once they have your money, you are forgotten. In the end, they will be forgotten because I advise everyone I know not to buy from Whirlpool.

Ice maker has stopped making ice on several occasions. Also when you try to get ice out of the door dispenser, it will continues to release ice but will not go down the chute and when you open refrigerator door it spills out all over the place. Getting ice other than from the door is no easy task. I have taken to putting a bowl under the ice dispenser. Interior of refrigerator is not user friendly for positioning items. Bought in a hurry back in 2017 and have regretted it ever since.

Today I had the unfortunate experience to have to deal with Whirlpool customer service and claims. I WILL NEVER BUY ANOTHER WHIRLPOOL PRODUCT again! My refrigerator, that was purchased in 2013, has a door misalignment problem. It is a known problem with Whirlpool (service pointer W107317828). My refrigerator serial number and model number are affected. Because I am outside the one year warranty, Whirlpool refuses to provide service that is required to fix this known issue with my model/serial number. After having to talk to four supervisors the only resolution that was given was that they would cover the cost of the 7/16 hex nut ($4.33). Dont get me wrong I do appreciate the offer.The two supervisors that were below her assured me that no one can do anything to assist me further. The attitude of the second and third supervisor was pathetic. After over a hour on the phone I was so disappointed that I could not take it further. The cost that we are talking about that I am asking them to pay is $154.28. I am very disappointed. They say they stand by their product. To me standing by your product means that you will fix or replace any known issue. $154.28. I hope it is worth it to you Whirlpool. You lost a long time customer.

Greetings: I purchased a Whirlpool refrigerator on July 3, 2014. And the supports for the door to open and closed have grinded and worn out - not allowing the door to close properly, requiring being lifted up, and pushed close as much as possible. Not the quality I expected with the purchase of a Whirlpool product. I want this door repaired or replaced at the expense of Whirlpool. Having paid over $600.00 for the product, I didnt expect no problems like this at all, poor design. The weight of the door is too heavy to support a hinge mount in plastic, its ridiculous. Now cooling is being wasted, runs constantly, and just not the quality I expected nor received.

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

I will never, ever, ever buy a Whirlpool appliance again. We bought the french door bottom mount refrigerator in 2013. After our warranty ran out, we had to have the guts of the refrigerator replaced and then the ice maker replaced again. Now the freezer door wont shut and I cannot believe that Whirlpool would put their name on this piece of junk! We splurged to get what we thought was a high end model but it has been problem after problem. RUN from Whirlpool!

We bought the washer and dryer set almost three years ago. Great sales pitch! Energy saver, extra capacity, low water usage, Whirlpool name and I thought we were getting great quality! Three years later I am disgusted, disappointed and am junking the washer. The dryer has a new heating element that we proudly fixed ourselves after the repairmen told us that these were meant to be throwaways. We just thought he did not want to work on it. After watching several YouTube videos we had it apart and found the issue was a cracked heating element. We ordered a new one for 100$ and spent another 4 hours putting it back together. If we had to pay a repairmen to do all that the bill would have been the price of a cheap new one. Fast forward three weeks and now the washer quit and it can be one of at least 15 problems. After reading all these reviews we have decided to toss it as junk. It took forever to was a load of clothes negating any energy saving! Whirlpool should be ashamed of themselves for ripping off all of us hardworking Americans selling us junk. At one time the Whirlpool name meant you could count on a quality product! If Whirlpool really wanted to do the right thing, they would stop selling these immediately and give customers a credit toward the purchase of new washers and dryers!

Whirlpool Duet Washer Trouble. Im having the same issue as Tom in Oakville. The F35-Sud errors pointed to the pressure sensor - NOT. 2 parts, a technician visit, and $800 later, Im still waiting on a Main Board replacement that is on nationwide back order. Time frame unknown.

Good Morning. We recently built a home with Pule in Nexton, which is located in Summerville, SC. The appliances we chose came with the dishwasher, stove and microwave. Everything other than the dishwasher has been doing great, but as for the dishwasher I am extremely upset...we are newly weds and received two nice sets of glass and at least 12 of them have been broken in the dishwasher. Please advice.

I had an electric 36 Whirlpool, smooth top cook top for 18 yrs. Worked great, cleaned with Windex and occasional scraper. Didnt show streaks or spots. I remodeled my kitchen 10/15 and bought a KitchenAid 36 glass smooth top vented cook top. What a piece of junk. Wish I had kept my Whirlpool. I can not get it cleaned. Every little fingerprint, mark, etc. shows. I thought KitchenAid was an upgrade to whirlpool but I was surely wrong. I am glad that I didnt change my built-in double oven. I did change out the Whirlpool quiet gold dishwasher for the KitchenAid. Again, wish I kept my Whirlpool. The KitchenAid is noisier, looks terrible with the stainless inside. Im embarrassed to open it with all the water stains. My Whirlpool was white inside and looked like new. I wish I had the money to change it back but I dont unfortunately. Moral of the story is if it aint broken dont fix it!

The inside glass of the oven door shattered. I have not used the oven for months. Only the the top cooking burners have been used. Its a mystery to me!! I have read complaints where the glass shattered while the oven was in use or being cleaned, but have found none where this happened to a cold oven. The large front burner is too hot. Even on the lowest setting everything burns. You cannot simmer, only boil. The control knobs have (in my opinion) no safety mechanism. I thought that the control knobs on stoves needed to be child proofed, hard for a child to turn on. My last stove you had to push down quite hard then turn to the setting. Not this stove. I have to be so careful when Im cleaning the area around the knobs. The slightest pressure and the knob turns. When I first purchased the stove while cleaning it, I unknowingly turned the knob and the kitchen filled with gas before I realized what had happened. I called Whirlpool thinking something was broken. They sent out a repairman. Nothing was broken. That is the way it is made. Customer Service said they had had no other complaints about the knobs. I find that hard to believe. My toddler grandchild can turn on the stove with ease. Im sure other concerned parents etc. have had this complaint. To sum it up... I will probably never purchase a Whirlpool product again.

I just experienced the same problem with my top load Whirlpool Cabrio WTW7800XWO. It is 3 years old, and I paid $900 for it. The plastic that surrounds the glass top is broken around the hinge. I had to pay $75 for American Home Shield to diagnose this and now I am waiting for them to order the replacement part - the part is around $190 from Sears or 245 from Partselect.com. What a pain. PLUS, the machine is so noisy and starts to vibrate loudly toward the end of the cycle.

We purchased the washer on April 25, 2015. It has been an absolute nightmare. Reached out to Sears within a week of delivery because the wash cycle was way over an hour. Is a terrible machine, my clothes come out dirty, is damaging my clothes and Sears says I cannot return it because according to them I havent had it fixed enough times. It washes for over an hour at times. It takes water and releases water and goes to wash again but is not cleaning the clothes. As a homeowner we pay water, and electricity and perhaps I wouldnt be so upset if my clothes would come out clean. At first the tech told me to change from the HE detergent purchased and recommended at Sears to liquid detergent and then since I still get stains on our clothes he advised me to use less than the recommended amount. I also purchased the kit to wash the machine. This is a real lemon and nobody wants to admit it. I have purchased Whirpool washer before but if they dont admit that this is poorly made and give me a voucher to buy another machine I will never ever in my life buy Whirlpool or Sears for that matter. The machine is just a year old and I cannot use it because it damages my clothes and worst, is not cleaning my clothes. It disgust me to wear dirty clothes or to have my family wear them. So now I have another appointment and at this point I no longer use the machine. I will tell everyone that is willing to hear my experience. Do not purchase this washer, is not good and is only trouble. You are not going to be able to get it exchanged or fixed. I think that a full year would have been enough time for Sears to determine this is a lemon and do the right thing by the customer. I now go to the laundromat because I have a machine that damages my clothes. I am also out of money to purchase a new one and the wearing dirty clothes disgust me.

I bought Whirlpool dishwasher (silver, Golden Series), after one year it just stopped for nothing and the circuit controller failed with error code E2/F2. So it was expensive but turned out to be totally unreliable. I had to pay $200 to get extended warranty and still waiting for the parts!!! Worst experience ever (uh Golden Series, for me it is Plastic Series). Will never buy any product from this company again.

We bought our Whirlpool Refrigerator a little over three years ago. Within a few months we started having problems with the unit. From ice maker issues, cooling and freezing. Initially the frig was covered under Whirlpools 1 year warranty. Then our extended 3 year warranty kicked in through HH Gregg which they supplied for free because of their poor handling of the initial sale. We have lost track in how many times a repair man has come out to work on the refrigerator. In the last year alone its been at least 8 times. The most recent problem had been the freezer not defrosting properly to the point where we had to store food in our neighbors freezer. The repairman has tried everything he knows and is stumped. Well our extended warranty has run out but theyll continue to work on the problem as long as we report the issue within 30 days which creates a whole different set of issues. The extended warranty states they will replace the refrigerator if it has the same problem 3 times. However what they dont tell you is that if you call BEFORE 3 time period its considered a recall and that doesnt count towards the 3 strike rule. We contacted Whirlpool and they wont cover the refrigerator because the repair company isnt on their approved list. Really a Sears repairman isnt approved? So buyer beware of a lemon Whirlpool Frig! They seem to have a way of not covering their product.

The Cabrio model (WTW5640XWO) I purchased in March 2011 died within days of installation. I was given instructions to modify the hose placement which resulted in a flooded basement and ruined carpet. Problems continued during the first year; several service calls. The problem was always the same; it did not drain/spin leaving a mess of soggy wet clothes. It died a final death - the same problem a few months after the 1-year warranty expired. The repair people have been out four times since. The last time, a $70 repair lasted less than 3 weeks for a bad shifter - always the same problem. Whirlpool will do nothing except offer to send a repair team out for a flat fee of an additional $120 with no guarantee they would fix the problem or replace the lemon. This week this Cabrio will be heading to the landfill. Ive had enough. No more Whirlpool products for me ever.

I have Whirlpool 40 gallon heater 5 years ago. The pilot light went out and I replaced the parts. This has happened three times and I have replaced the entire thermocouple assembly three times. The last time, the parts came straight from Whirlpool. This time, the pilot light will not stay lit. I am on my way to buy another hot water heater for my family because I have had enough.

We purchased our fridge February 2017. It stopped working September 2018. It wasn’t staying cold. Under manufacturers warranty a repairman was sent out to assess the problem. They had to order the part that went bad. A week later the came back and “fixed” it. Total time missed at work 1 day. It stopped working again April 2019. It wasn’t staying cold. Under our Lowe’s extended protection plan a different repairman was sent out to assess the problem. They had to order the part. A week later they came back and “fixed” it. Total time missed at work 1.5 days. Yesterday (July 2019) we noticed it wasn’t cold AGAIN. Called Lowe’s and was told they could call it a Lemon and replaced until the 4th time it needed repaired. They would need to send out a repairman and assess the issue and make a repair. Our 3 yr extended protection plan expires February 2020. So we’re probably not going to make it Lemon status within the warranty. The fridge is French Door Bottom Mount model. Do NOT buy this refrigerator!

Just had the repairman at my house to repair my 2-year-old Whirlpool refrigerator Model GB2F4DXWS07 - he couldnt fix it. Just throw it away and get a new one. There is a blockage somewhere in the line, he suspects the lines were not cleaned before it was charged at the factory. Repairman said it was a typical 20-year-old refrigerator problem. Customer service was no help - Whirlpool live chat is currently unavailable. Lousy product with worse service. I will never buy another Whirlpool product.

I bought a Whirlpool High Efficiency top load washer. It does not get the clothes clean. Dark clothes come out with spots all over them. There is not enough water to rinse out the dirt. It is left on the clothes in spots. I have to take my clothes to the laundry mat to wash them to get them clean. I am 74 years old and have used Whirlpool appliances all my life. I have dt3 rental houses I keep Whirlpool appliances in. But I wont be buying any more. I had to call the repair man one month after I bought it. He had to recalibrate the machine. If all you want to wash or maybe rinse out is a pair of slacks or a shirt, it might be o.k. but not a load of dirty clothes. It is just a JOKE.

I cant begin to tell you what a pile of crap my Whirlpool range with Aqua Lift cleaning is! We purchased it brand-new and it is the slowest oven on the planet! If I want to cook a pizza I have to call home 30 minutes in advance so the oven will be 1/2 heated up. The Aqua Lift has never worked and the company has the most abhorrent customer DIS-service Ive ever had the misfortune to deal with! I hope these scumbags go bankrupt!!! AVOID anything Whirlpool! There is a class-action suit in the U.S. over what a slime bag bunch of crooks they are and how their Aqua Lift technology has NEVER worked!!

First, I was put on hold by the first female for 44 minutes, and then a second woman finally answered, and said she didnt know why she would send me to her, because she was in the sales department, and she put me on hold for another 25 minutes. I finally had to go, because I had an appointment. When I got home, I called back, and got a man by the name of John, and at least he recommended he could schedule a repairman. The problem I told him is, the inside wall of my refrigerator has 2 cracks on the side, and a crack on the back wall. I dont want a repairman to come, just to tell me he cant put 2 new walls inside of my refrigerator. I could not find an email, so I could email Whirlpool about this problem, and definitely, they were of no help. I bought the refrigerator at Lowes late 2003. I have never, in my life, seen the inside walls of a fridge do this. I spent a lot of money for this, for it to crack on the inside walls. It does not seem like something is right with this.

I have had my Whirlpool stove for over 30 years and use it daily. Still a great stove. I would not trade this stove or any of the new types. I just need to get the self cleaner repaired. The only problem I have is finding parts to fit this older stove.

Weve had this Whirlpool 5000DW1 machine since June 2017. Never fills with enough water no matter what cycle you pick! Clothes come out with DRY areas on them! Obviously not clean. Who would design a washer that you put soap in and clothes right on top of that! Seriously, how ridiculous. I will forfeit the money spend on this junk if its possible to find something built today that cleans clothes.

My elderly mother purchased a Whirlpool Washer Mode Number WTW4955HW1 in November 2020. The washer has had nothing but problems. It leaks, vibrates and moves on the floor. My mother called Home Depot to see what she needs to do, and they said once they deliver the product it is out of their hands. Had our first service call in May 2021 by an authorized service and he said they should sell this on eBay. It is a horrible product, he said there is nothing he can do. Had a second authorized service in June 2021 and they said we needed a new tub which they ordered, and he said this will take up to 2 months, they also said to do only small loads and only use the deep-water wash and deep water rinse. After the technician left the agitator now comes apart. Would not recommend this product to anyone and I would never buy anything at Home Depot because they do stand by the products they sell.

We bought a Whirlpool Washing machine a couple of years ago. We have been having problems. It does not get the clothes clean and laundry has an odor to it. We bought it at HHGreg by the Dayton mall in Centerville, Ohio and also bought the extended warranty. It was the largest capacity machine they had in Whirlpool so I dont need to mention what we spent for this thing. We have had a service tech out 3 times. The first time he replaced a part. It still didnt fix it. So they were out two other times saying nothing was wrong with it. Not only is it not getting the clothes clean, but is putting lint pieces all over the laundry. The warranty place already said if they come out again and they cannot find out what is wrong, then we would have to pay for the service call. We then went to the store we bought the machine and talked to the manager. We got no help from him. All he did was throw us back to the warranty place. Not to mention, the family is having itching problems with their skin because the clothes are not only not getting clean but the soap is not rinsing out. In other words, we are suppose to eat this expense and move on. This is a new machine!!!!! And all it is worth is taking it to a metal place to scrap out!!!!! We will never buy another Whirlpool product again. It is really **. They don’t back their products up and do the consumer right. There are a lot of complaints online about the same identical thing I am writing about. They should reimburse the people the money that they wasted. Thank you.

My brother bought my 80-year-old mom this range so that she could bake all her delicious desserts with ease in a new beautiful oven. I was at her house visiting and saw that she was down on her hands and knees cleaning her SELF-CLEANING OVEN. She tried several times using the useless AQUALIFT FEATURE but to no avail. In this day and age with self-cleaning technology, WHY would Whirlpool install this unbelievable bad AQUALIFT cleaning feature? To see my poor mother scrubbing the inside of the oven like she did back in the 50s & 60s just completely appalling!! PLUS the top surface enamel is bubbling up with rust and the oven is only 2-3 years old. So we are trying to contact Best Buy to see if we can get a refund on this HORRIBLE appliance.

I redid my kitchen two years ago. Put in Whirlpool appliances because they matched my refrigerator. I have been very happy with all aspects. It looks good, it’s easy to clean and cooks well. It doesn’t have a lot of special settings. Less to go wrong.

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

Purchased Whirlpool Microwave 1.6. The design has 5 BIG flaws. 1. Too large in depth, cabinets on each side cant open. 2. The one light under unit is so far to the back wall, you need a flashlight to cook spaghetti or use stove. 3. Too large in height, cant get a big pan on your stove. 4. Top of unit is open so much, if you spilled something from the cabinet above it would go right inside the works. 5. Instructions are hard to read & figure out, the wall hanging support is just one piece and if you dont have 2 main beams youre out of luck. GO buy a GE, put it up in 1/2 time & good & secure and works great. Has 2 lights on each side under unit. Fingers over the holes at the top. 1 inch shorter, 1 inch thinner. To my surprise the turntable is even larger, go figure.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

Our side by side refrigerator is 2 1/2 years old. The LED lights are not working. Had to call repair service because one cant get into the housing without a service tech No9 normal screw in light bulb to replace 2 burned out light bulbs AND pay for the service call is $475.00. THIS IS HIGHWAY ROBBERY. I would expect to pay for a major repair BUT A LIGHT BULB. DO NOT BUY A WHIRLPOOL REFRIGERATOR WITH LED lights. This is a major flaw in their manufacturing and If they go out again the fridge will go to the landfill.

After buying the best washer and dryer out there, I have found out that they are not. Thank you Whirlpool for taking my $2000 and giving me a junk. I know that you do not care one bit. Never again.

After months of careful research and comparison, I finally bought a pricey (over $2K) Whirlpool refrigerator with a bottom freezer and French doors with water dispenser on top. I really did not want any fancy features, just narrow doors because of my small kitchen, and a fridge on top because of my back pain. Since the date of purchase in May, 2014, I have had 4 service calls. The first was covered under warranty, but no cause of the sheet of ice collection and underside water leakage was identified; I did, however, receive a somewhat patronizing lecture on the importance of thorough reading and comprehension of the owners manual, and a statement that most of my service calls are for customer education. A follow-up service call, a few weeks later and also covered under warranty, identified the cause of the ice collection and water leakage: a faulty duck bill little piece of plastic in the drainage system that is a problem well known to Whirlpool. In mid-June of 2015, the ice maker had to be replaced, to the tune of $360.00. Today, I had a service call ($103.00) and received an estimate of $405.50 to replace the broken freezer drawer slides, which prevent the freezer drawer from fully closing. I will be applying that $405.50 to the purchase of the simplest model, non-Whirlpool refrigerator available, and have the Whirlpool hauled away. Besides the problems noted above, the center of the refrigerator freezes the food, while the freezer compartment arbitrarily defrosts. There are alarm icons that go from blue to red to alert you of the need to replace the (expensive) ice and water filter, refrigerator air filter and crisper freshener. Alarm bells ring to inform you that the doors have been open too long, but nothing alerts you to the fact that the freezer door is not completely shut, or that the freezer has gone into defrost mode because someone inadvertently brushed up against the control panel and changed the settings, or that water is pouring freely out from underneath the appliance. I have had to change my buying habits because fridge holds at least 15% less food, even though it is the same cubic footage as my previous (top freezer) one. Freezer contents easily slip down behind the top freezer drawer and jam the door open. I have to take most frozen boxed items out of their original containers and pack them flat in freezer bags to get enough storage. Some tall bottles do not fit anywhere in the refrigerator compartment, and have to get put in sideways. Even in the absence of mechanical problems, using this refrigerator is like packing and unpacking a suitcase many times a day. While Whirlpool customer service personnel were not overtly rude, there were dismissive and condescending overtones in some of the questions and directives I received from them, and another insinuation that service calls would not be covered under warranty if they end up being for the purpose of customer education. The extended wait (7+ days) for appointments with a Whirlpool-certified appliance repair company, along with the customer education exclusion, were absolute deterrents to the purchase of the extended warranty. Besides my personal disappointment and disgust with the purchase of this appliance, I am sad to see that the Whirlpool brand has slipped so far in product design, quality and customer support.

We bought a Whirlpool washing machine, and what a mistake! I just got off the phone with their customer we dont care department. It spins everything into a tight ball so when the clothes come out of the washing machine everything needs ironed, even permanent press. It also changes the water temperature. I like to wash some clothes in cold water, but the representative at Whirlpool told me it will sometimes add hot water to make the water warm. I am hoping this review will save others from purchasing a Whirlpool washing machine. We will stay clear of all of Whirlpool appliances due to the problem with this washer and Whirlpools lack of concern of an inferior product!

FRUSTRATION!!! It is unbelievable that even appliances have become DISPOSABLE! Where are the days of when our parents bought well made appliances that LASTED 20 years with NO problems??? There was satisfaction knowing that a purchase of an appliance was $$ well spent! These days it costs MORE to replace parts than IF you purchased a brand new machine! We purchased BRAND NEW Whirlpool Duet Sport Washer AND dryer in 2007. The washer has been repaired a total of 5 times and the dryer 3 times!!! IN A SPAN OF 10 YEARS! Are you serious?! With the $$ spent on warranties/ labor/ parts: WE could have purchased new appliances. What is WRONG with this picture? IT IS ALL about making money on REPLACING PARTS/WARRANTIES/LABOR!!! Forget the consumer that is spending THEIR hard earned money to buy the appliances initially. Short of going to a laundromat, the consumer needs to purchase a washer & dryer. So I guess it is a vicious cycle of REPAIRS/REPAIRS AND MORE REPAIRS!!!

Within 5 months my 850$ dishwasher broke. 2 months to repair and 15 plus hours on the phone. Warranty is cryptic. You must allow them 30 business days from when they order parts. Buy Bosch, wish I did!

I bought a Whirlpool washer and drying matching set (model 6400sw3). I liked it because it was extra large without agitator in the middle. Ive had it for about 2-3 years and I have already replaced the drain pump, motor and barrens, it has cost me over 500.00. I thought now OK its working fine, but now its giving me a code every time I wash of LD. I am so fed up with this!! I should have bought a new washer but I felt as much as I put into it, I basically built a new one. And now this code comes up every time and I have to power it off. Im not sure if anyone else has had this problem but I just dont know what else could go wrong with this. I will never ever buy a piece of junk like this again!!

First one had major problems. The bladder they call it. They took out the whole system out, replaced the tube that goes to the top of the refrigerator which is where it always starts leaking so they worked on it three times, junked it, gave me a new one and here I am again same thing. Ruined my hardwood floor and Im stuck with it. Never again will I buy WHIRLPOOL.

This is a good looking, inexpensive stove/oven. Stove top has four burners. I liked the split grates on the stove top. Its easier to remove and clean. I do not like the rubber seal on the oven door. I am used to the heavier duty seals on most oven doors.

I bought a Whirlpool fridge 4/23/2013. Thanksgiving it went out. I had a repair company come look at it to see how much it would be to repair. He said the compressor was out, it has a freon leak, and the electric board has a relay that is acting up. Basically it would cost $600 or more to fix. I only paid $750, mind you. Whirlpool customer service said if we pay to have it fixed then send them the paid receipt. They would then give me a 6 month service plan for future repairs if needed. Please tell me how that helps me now? A voucher for $200 or offer something to help me now. Not a happy customer. Thanks for nothing Whirlpool.

Originally installed early 2007, the very expensive unit went crazy after about 14 months, with random beeping noises, and non-response to keyboard entry. Sometimes unplugging the unit worked. When unplugging no longer worked, the unit was repaired by replacing the keyboard logic boards only to fail again the same way.about a year later. It appeared the heat or steam from the cooktop below the microwave was causing the failures, so we became careful to ensure the fan was on. Last week, after boiling some water, the unit failed again, with error code F2H2, the keyboard error. Didnt Whirlpool expect the microwave to survive heat or steam from the stove/cooktop below? Overall, the unit is great when it works. Unfortunately due to the large size of the 2 cu ft unit, only an identical unit will fit. Im skeptical of replacing my broken unit with another Whirlpool Velos unless this keyboard problem has been fixed in new units. Anybody know if Whirlpool has fixed this problem?

I spoke to Sue in Tennessee that refused to let me speak to a supervisor regarding replacing a light bulb in my microwave. Sue insists that I can do this, despite no instructions in the owner’s manual and warnings all over about electrocution if I open the panel. Sue refused to assist me and is sending out a repairman. I will never do business with this company again, and I am angry that Sue refuses to see a problem with me paying $75 to replace a light bulb in a nearly new microwave. She continued to give me incorrect instructions on how to replace the bulb, and the owner’s manual does not have instructions nor do they exist on the internet. The owners are not supposed to dismantle this model, but Sue at Whirlpool Customer (no) service told me that I have to pay. Seriously? For a less than two year old microwave? Never again. I think I will take this unit out and get a GE.

There is a chronic and well-known problem with recent French door, bottom freezer refrigerators sold by Whirlpool, including the the brand names KitchenAid, Jenn-Air, Maytag, and Amana. The problem is caused when the defrost drain freezes, preventing defrosted water from reaching the evaporation pan. After enough water builds up, it overflows along the front of the refrigerator. In my particular case, we have wood floors and they were ruined by the water. After doing some investigation on the internet, I have learned that this problem affected approximately 1,500 model numbers sold under these names. These model numbers are listed in a Technical Service Pointer issued by Whirlpool.In August 2013, after experiencing several years of problems with these units, Whirlpool issued a Technical Service Pointer W10632338, advising service technicians that a new P Trap drain tube kit was now available, and suggesting that the defective duck bill check valve should be replaced by this new part. The problem for years had been that the rubber duck bill check valve would, over time, become sticky (or tacky) and would then not open - causing water to build up above it. Eventually, the water would freeze and since newly defrosted water could no longer escape, it would build up and eventually overflow.From what Ive seen online, plus a conversation with the Sears technician who come out to diagnose and repair my leak, I am convinced there are many thousands of customers who have experienced this problem. Because it takes a while for the rubber check valve to become sticky and no longer open, it is not uncommon for the problem to not appear until after the standard one-year warranty has expired. From reports, Whirlpool has sometimes acknowledged the problem and effected repair of refrigerators no longer under warranty.But what about those customers, like me, who have experienced water damage to floors and cabinets? Shouldnt Whirlpool be liable for those repairs, too? Id be interested to know if anyone knows of plans for a class action lawsuit.

Water heater was defective from the factory with a pinched wire between the thermostats. After replacing everything on the heater Whirlpool would not reimburse any parts or labor for the unit... Whirlpool is dead to me now, and forever and I love to tell my story to prospective buyers of their products!!! So far, to date I have cost them about 14 sales of major appliances (and still counting!!!). After reading some reviews… Im (sorry, I omitted the personal insults) in respect of your review guidelines.

We recently bought a Whirlpool front loader even though the reviews kept mentioning mold and odors. I discovered that there was a water buildup in the soap dispenser so after every load, I remove, clean and dry the soap dispenser. The machine does a great job on cleaning clothes and I am following other suggestions on cleaning the drum from time to time. By the way, I bought my machine at Lowes from the scratch and dent department and with a little negotiating, I paid half price! Good deal and so far, good machine. Good luck and remember to remove and empty the water from the soap dispenser!

This Maytag dishwasher is awful. The parent company is Whirlpool and their customer service is as bad as their products. I bought this dishwasher and less than a week later the pump isnt working and stagnant water is sitting in the machine. It took Whirlpool 3 weeks to replace the machine and they sent over another defective machine. This time it lasted less than 2 days. The Whirlpool customer reps are rude and vindictive and antagonize the customer with their lack of service. Called corporate office with no help from Cust. Service and was told to leave a message with the operator and await a callback. With this fiasco I wouldnt buy another Whirlpool or Maytag product again. BTW. Im still awaiting my callback from the corporate office... Im not holding my breath. I called the company that I bought the dishwasher from to see if they can help me unload this machine and get a different brand...

After 22 years, I replaced my Whirlpool, electric, 50 gallon water heater, due to age and it was still working well. Went to Lowe's and they do not carry Whirlpool any longer, so I purchased and installed an A.O. Smith water heater, electric, 50 gallon water heater, model ES12-50R55DV110. Hoping for as good a product now, as I had from my Whirlpool. Also, I installed myself.

Cabrio Whirlpool washer - I hate this washer. Had it for about 3 years now and it will not spin out and does not give a code. Called a service tech out and they cannot find anything wrong with it. The water goes out but will not spin. It sits on 20 minutes and does nothing. Will not buy another Whirlpool washer. Wanted a good washer and got a piece of junk. Will not recommend it to anyone else. Think Im going back to the old style.

My dishwasher is more than 10 years old. It functions but the interior baskets have broken and because my counter overhangs a couple of inches from the dishwasher the steam from the dishwasher has damaged the underside of the counter. It cleans ok but I would not buy this kind of dishwasher again.

We purchased Whirlpool AquaLift oven from Lowes 10 months ago. Since then, I dread each time I use the oven because I end up cleaning it by scrubbing and using different products because AquaLift cleaning is a scam. I have arthritis in my joints especially my neck, so cleaning it by sticking my head inside is a nightmare for me. I will try to call the company and see what is going to happen. I read that someone is suing Whirlpool for this product so hopefully they will recall the product or refund us if we return it.

After only two and a half years, my Whirlpool bottom freezer refrigerator (GB2SHDXTQ0) was frosting over and the top food section stopped working altogether. I made a call to Lowe’s. It’s not their problem. I then called Whirlpool and he said I had a bad gasket. I had a 28-year-old refrigerator that was still working with the original gasket and it has no problem. After reading all the complaints with Whirlpool, I would never buy another one again. After cleaning out the refrigerator and freezer two times, carrying things to a friend’s house and having to pay $90 service calls just to walk into the door, I am ready to throw this one out. This refrigerator cost me $1200 and I am a single person living on $900 a month. Thanks for nothing, Whirlpool. There should be a class action suit.

We purchased our first Whirlpool product, a washer, model WTW4800XQ 2 years ago. Started having problems with the clothes dripping wet after the wash cycle. Turns out the 2 year old washer needs a shift actuator and a wire harness that will cost close to $400 and take a week to obtain! I have had Kenmore appliances for the past 35 years. Ive never been disappointed it their performance or longevity. Each appliance lasting 15+ years and in the case of my fridge, it lasted 30 years! I am very disappointed in Whirlpool and WILL NEVER purchase another whirlpool product.

Whirlpool Duet pair. Like Whirlpool products and have had good experience with them. Have had the pair for 3 years. Like the way they wash and dry. Clothes do not take a beating. Only dislike is the vibration on the washer. I look for capacity and extra features such as: steam option and extra cycles. Now I also look for noise and vibration. Would definitely like to stay with Whirlpool. Definately cost is important, but for the sake of a few dollars more the options and the brand are something to be considered. Having a steam cycle and wrinkle cycle are important in any dryer.

I purchased a Whirlpool WTW6600SW in January 2010. I dont normally purchase an extended warranty, but it was a fairly expensive washer. So I did. In July 2011, water starts gushing all over the floor. After my first visit to see what is wrong, I ordered a part. I was out of a washer for 2 weeks. Then in August 2012 the same thing happened. This time the repairman didnt get the part on properly, so they had to come back a third time. I am out of a washer for about 3 weeks. Now, October 2012, it is doing the same thing again! Customer service tells me it has to be repaired for the same problem four times in the same 12 months in order to receive any replacement value. It will have to break two more times! This washer is a piece of junk!

In the middle of the evening the door glass spontaneous shattered with nobody around. Its only a 3 year old microwave builder installed in a new home. Ive always heard Whirlpool appliances are garbage but this proves it 100 percent.

Bought the Whirlpool Duet washing machine. It lasted around eight years. In the meantime I was replacing the rubber door seal cleaning out the pump constantly. The plastic pieces inside the drum all broke. Every few months I would get an error code. And During spin cycle it would literally shake my entire house. The problem with all the front loaders is the construction of the drum and the drum bracket. They are made of dissimilar materials. (Stainless and zinc) When you add soap to the water then the bracket becomes an anode and the drum becomes a cathode, which creates electrolysis which corrodes the bracket. When the bracket breaks your machine is totaled. I’m finished with every manufacture except Speed Queen. I bought a Top loader Speed Queen and I love it, it is built like a tank.

I’m a 69 year old married man who has probably owned about 8-10 clothes washers during my life. I purchased my first Whirlpool washer about 1 1/2 years ago (Cabrio - model WTW8500DC2). It began leaving sediment on my clothes immediately, even though I followed the specific washing instructions. Whirlpool sent 3 different repairmen to fix the problem, each indicated there had been problems with this machine. None were able to fix the problem. When I called Customer Service for the 4th time, they refused to discuss the problem. They said there was nothing wrong with the machine, it was my problem, I must have too much “lint” in my clothes. Haven’t had that problem for 69 years, but this was their way of handling the problem. They refused any further help. I would discourage everyone from buying a Whirlpool product. I absolutely do not back their products. You are on your own!!

My Whirlpool Cabrio washer (WTW6600SG2) is a money pit! After reading all of the nightmare stories concerning this washer one would think Whirlpool would offer a recall and try to correct their wrong doing. Do not buy a Whirlpool Cabrio. It was the worst decision I have ever made! Whirlpool does not stand behind their products. I cant believe they can get away with treating their customers so unfairly, taking their hard earned money for crap like this, then not offering to help after so many have had issues. The Cabrio is loud, doesnt get clothes clean, and is always flashing UL for uneven load (when it works at all). My local repairman has made many trips to fix my problem Cabrio. This time he is at a loss. Ill be buying a new washer and it will not be made by Whirlpool! Please, if you are reading this be forewarned!! You will regret your purchase if you buy a Whirlpool Cabrio.

Havent had any issues with it. Works great but does end up off balanced quite easily and halfway across the garage. Washes clothes like a maid. Is kinda small for bedding.

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.

Bought this washer in May of 2019: Whirlpool - Whirlpool - 4.5 Cu. Ft. 37-Cycle High-Efficiency Front-Loading Washer with Steam and Load & Go™ XL Dispenser - Chrome Shadow. Model: WFW6620HC. SKU: 6313774. Paid over $1,000.00 for it. FIRST TIME washing our sheets, we had snags & rips. I immediately called and was referred to Whirlpool and then referred to an outside repair company. They sent a technician out who said everything was functioning properly despite having ruined 3 sets of sheets (these were not all washed at the same time & I didn’t realize they were being snagged until making the beds).I continued to use the washer - clothes were fine, but yet again, MORE sheets and now comforters RUINED!!!! I called YET AGAIN after troubleshooting the problem myself and finding that the drain holes in the drum had metal pieces sticking up causing the items to snag & rip. Another day taken off work to stay home for the repair. The repair guy comes out, the part was broken. So now I’m left once again with a faulty washing machine AND no ETA on when the new part will arrive and be installed AND having to take yet another day off work.7 sheet sets, 3 comforters, multiple shirts, & multiple bathing suits RUINED & was told there was ‘nothing they could do!’ I will NEVER EVER AGAIN purchase anything with the Whirlpool logo. It’s JUNK! Just an FYI, this was initiated in May of 2019 and it is now the middle of September 2019 with no fix updates. Who can go months without doing laundry???? Once again, poor customer service and JUNK of a product!

I have many rentals, and for over 39 years have always bought Whirlpool dishwashers for them and my own home. I have noticed over the last 15 years or so they are getting more and more poorly made. First I quit buying the plastic tub ones because they collected mold on the back. Then putting one in a rental, we went through 3 brand new ones that all leaked before we got a good one. Now, I bought the very best for my home 2 years ago, had the pump replaced under warranty due to leaks. Now, the plastic upper rack wheel has snapped off its plastic base. For under 30 dollars you get a replacement kit for it, that is all metal. So why didnt Whirlpool just put in the metal ones and charge a little more. So this will be my last Whirlpool, and all the brands they make. Do your research, many of the name brands you know are all made by Whirlpool.

Bought a Whirlpool Cabrio washer and dryer 5 years ago and with only 2 adults and 4 washes per week, it broke down twice needing new motherboards each time and, of course, Whirlpool would not take any responsibility as the 1 year warranty had past! I will not buy another Whirlpool!

Whirlpool Cabrio Elite Top Loading Washer Model WTW8240YW - I add my complaint to the roughly 2000 others about this machine and Whirlpool. Two months after the warranty expired the machine started making a loud noise on the spin cycle. I called a repairman and he said it was the main bearing going bad and this was a common problem with this model. He recommended buying a new washer rather than repairing the unit because the cost to repair was greater than what I paid for the washer. I called Whirlpool and all they offered was to send a repairman at my cost. This is terrible service for a documented problem that they have. I will buy a new washer but it will not be a Whirlpool!

The Whirlpool dishwasher is the best I have ever had! The pot scrubber just cleans anything off the dishes! I hate to wash dishes before I put them in the damn dishwasher!

I bought my Cabrio washer 16 months ago to service a family of 4 adults, 2 children and 2 dogs. Anything that has the slightest stain has to be pre-rinsed or pre-washed in the sink before going into the washer. Every load is an unbalanced load. Although the floor is perfectly level, the washer bucks and dances as though it is possessed. I never expected a $900 washer to be a piece of junk. I would love to be part of a class action lawsuit regarding this washer.

Bought Cabrio 3 years ago, started getting ul code and f1 code. We leveled machine, but cycle kept getting stuck mid-cycle. Called repair guy, they say it is going to cost between 6 to 800.00 to fix???? Really. Its three bloody years old. Very disappointed. Do I now get it fixed or break down and buy another washer. I would not buy Whirlpool again. Very pissed.UPDATED ON 02/05/2015: We called an appliance repair company and initially paid $440.00. After installing a motherboard computer system, it still did not work. We were then told that the other part would be another $120.00. We were already soaked for $440.00 so we decided to pay. After that was repaired the washing machine was still stalling mid cycle. We were then told that it has something to do with the wiring and it would cost another $120.00-$140.00. Needless to say, we declined. Complained to whirlpool that machine was three years old. We are pissed and $570.00 out of pocket. Just bought a lg front loader and paid for a 5 year warranty!!

I know that appliances are made to be disposable, but throwing away a $40 toaster after 18 months is easier to live with than throwing away a $350-$400 dishwasher. We bought a new dishwasher at Lowes on October 15, 2015. It is now May 11, 2016. The manufacturers warranty was for a year. It has been about a year and half since it was installed. Not very long for an appliance that one would assume would last at least 5-10 years. When we called Whirlpool to see about a repair visit, we were told that the trip to the house would cost $105, and the parts could go as high as $250-$300. So if you weigh the original price to the repair price, having it repaired is not rational, but neither is throwing away a dishwasher thats almost new. Its still clean inside. No soap residue or anything in the tub. In the past, by the time we were in the market for a new dishwasher, our old dishwasher looked like it had been through the war. It just breaks my heart to know that a company is so slipshod at making appliances that they wear out in less than two years. There doesnt seem to be any recourse but to dump a perfectly good, relatively new dishwasher in the landfill. We are leaving a very big footprint by doing this.

I purchased model FG1F4040SEPV Whirlpool water heater from Lowes about 5 years ago and have had to literally replace the thermocouple each year. At least 3 of these years we have had to pay someone to fix this for us until we learned to do it on our own. Im very surprised Whirlpool didnt recall these water heaters and make it right for their consumers. What this did for us was confirm that we will never purchase another Whirlpool item ever again. We are switching over to Kenmore!

If you want clean clothes dont buy this machine(Cabrio Washer)! First of all I find that my clothes have dry spot on them when I pull them out of the machine. Whirlpools response is that the machine spins at such a high rate that the cloth will actually seem dry. Doesnt make sense to me that a shirt that has another garment on top of it gets dry in an unexposed area. I have also been told to always use the high water setting. This helps but the clothes still are not clean. Also my dark slacks come out with residue lines on them - Whirlpools solution; never wash anything in cold water. In addition the machine is very noisy. It sounds like the water pipes are being kicked out of the wall. And forget about washing a king size comforter as advertised, a twin comforter doesnt get clean or even thoroughly wet and residue lines are left behind. Hate this machine! So glad I didnt buy the extended warranty since my attempts to have them stand behind this product have failed. I feel the money would be better used towards a different brand.

Whirlpool Cabrio washing machine is less than five years old. First repair was replacement of control panel (under warranty). Second, third and fourth attempts to fix the out-of-balance problem which continually caused the machine to shut down altogether (even a small load) left my repairman totally frustrated after replacing most of the parts, finally telling me it just cant be fixed! What? I paid over $1,000 for this machine in Oct. 2007 and expected it to last many, many years. My mother-in-law has a washing machine she bought used in 1979 and it is still working beautifully. Ive read the 14 pages of complaints on the Consumer Affairs website and agree with Diana in Kissimmee, Fl - I am sick to my stomach not only for Whirlpool not recalling the Cabrio, but for Lowes and Sears and any other supposedly family-friendly business for continuing to sell it! Someone please contact me if you know of a class action suit being filed.

This $1,000+ Whirlpool Cabrio washer high-efficiency machine should have lasted between 10-15 years, not 1, not 2, not 3, not 4, not 5! To expect less is to fall for the consumer cave in - where you just give up, give in and buy another. The Whirlpool tech just told the appliance repair guy that was here that the repair would involve a recirculating water pump and a bearing, and would cost $481 to repair. The appliance repairman said he is not in business to condemn appliances, but said he has a Kenmore top loader at his house. Simple, no electronics and less things to go wrong. Well after researching brands and reading reports, I thought I was buying a machine that would last at least as long as my second hand Maytag. Whirlpool has not heard the end of me. I have heard several other people say the same thing. Repair bills are huge and machines do not hold up. So much for buying quality. Now Im going to contact the MA attorney general for the states implied warranty, which means if you spend your money on any appliance, that appliance has an expected lifetime of service. A $1,000+ machine is not expected to fall apart after a few years.

I bought a compact washing machine and 4 months later it broke, needed a CCU board. To make a long story short now the machine is 7 months old and still broke. Whirlpool cant locate a part for it nor do they want to replace it. I think its time to get a Lawyer involved. Ive been calling for weeks now and have gotten nothing but the run around from all very Rude employees. Im turning this over to a lawyer. Im done dealing with Whirlpool. For a large corp Im very aggravated and severely disappointed with them. Wish I never bought their appliances. NEVER AGAIN.

I do not use my oven much, mostly to heat up something. I noticed all of sudden I couldnt get the microwave to work at the same time as the oven. Then the controls stopped beeping. Then I went to heat up the oven and it started smoking and had a terrible smell. I am two weeks out and still no microwave or oven. The repairman was very nice. Came out and ordered parts. I wanted a new oven and I was told no. Parts came in. Repairman came out and nothing worked. Waiting, waiting and waiting. I will never ever purchase a Whirlpool appliance again. This is not my first bad experience with them. I thought maybe they got better but that did not happen.

My Cabrio was built in April 2016, its now Feb 2019, and its not working. Shows error code of LF, the inlet water value is bad. I bought a Sears protection plan, repairman comes out, tells me no-one has the part anywhere, its backordered and no way to know when it will deliver. Sounds like a scam so Sears doesnt have to fix it and Whirlpool makes little to none of the part so you have to buy a new machine. This machine also takes forever to wash clothes, sometimes part of the clothes come out dry because not enough water. Its a huge tub, but of no use because theres not enough water to clean properly therefore, you have to do small loads. I always put it on high water because the other features like, quick wash & normal do not give but only little streams of water! The first one I had delivered made a funny noise from day one so Sears replaced it the next day. This one has NOT even lasted 3 yrs. There needs to be new legislation placed upon these companies with regards to the products they make. It should be illegal to make such junk and be able to charge high dollar for it and it doesnt operate well or last very long. They are laughing all the way to the bank on everyones dollar, intentionally making products that last less than a few years! I Will NOT purchase Whirlpool or any of their products again! They owe me a new Cabrio and Im going to make sure I get it and get my moneys worth! DONT WASTE YOUR HARD EARNED MONEY ON THIS JUNKER! DONT BE FOOLED BY ITS PRETTY SLEEK LOOK.

I find this to have perfect storage space both in the top for standard refrigerator and the bottom freezer. I would recommend this not for the style, the amount of room but also the quality. I have not been disappointed.

This is truly a piece of junk! My water heater is 2 1/2 years old and the pilot light will not stay on. Was told that I needed a thermal coupler and paid $30 for shipping. Installed it and still the pilot light will not stay on. Was told again that I needed to replace the main control. Another $30 for shipping. Had that installed and the pilot light stayed on but no hot water. The light was blinking 4x (temperature too hot). WHAT!!? ALL I GOT WAS COLD WATER! Now I was told I need to replace the temperature sensor and they wanted another $30! I told them to I was going to junk it and buy a different brand.

I am very disappointed with the purchase of a Whirlpool Cabrio Washer and Dryer I made about 3-4 years. The price was too high and the quality is extremely poor. It has a leak in the pump which will cost me $300.00 to fix. I probably would have been better off buying the cheapest washer and dryer set they had. At least, those actually wash the clothes and dont breakdown. Never again will I buy a Whirlpool and I will get every chance to share my opinion of them.

The wash machine is JUNK. We paid $2500.00 for our washer & dryer at lowes in 2012. I HATE IT from the start. It has destroyed most of my clothes. I hate doing my clothes. The water does not get my clothes wet, they dont get them clean AND the washer dont even get them wet. THEY need to do a recall or get us a lawyer. ALL the money I have put in this washer. The price we paid for them is a SHAME. IT is WRONG they are telling people that this washer is the best. They lie. I HATE HATE THEM.

Bought the HE Whirlpool Cabrio in 2013 after having my old agitator Maytag for 19 years. After reading the other reviews I do not feel alone. An awful washer, a year after our purchase the spin cycle is so loud we have to close the laundry room door. Now it has been leaking into my basement. I called a repairman, explained my problem. He suggested to junk the washer, it will cost more to repair than buying a new washer. In addition my clothes did not clean properly, soap stains on clothes because it does not use enough water. This was about $1000 purchase that lasted less than 4 years! I am done with Whirlpool and suggest to anyone not purchase a HE washer, nothing like the old style agitator washers.

The trim on the front the my Whirlpool electric range has rubbed off. This is where the knobs for the burners are located. It was replaced once during the Whirlpool 1 year warranty (so it obviously happened with the first year!) and again during the second year we have had it. We have an extended warranty but have been told that it is not covered. It is ecstatically unacceptable. We have not used any type of harsh cleansers on it - simply a sponge to remove any spills yet it keeps on disappearing. I strongly recommend against buying any range from Whirlpool as it is quite obvious that they do not stand behind their products beyond the first year.

Rather than replace the heating element in my 15 year old Sears dryer, I opted to replace both my Sears washer and dryer with a new HE Whirlpool. It was the biggest mistake that Ive made. The washer does not have an agitator and the clothes turn into a twisted knot. Deodorant did not wash out of load of three sweaters. When I called tech support, the woman told me that the washer met specification. I suppose that means that it uses only limited water but has nothing to do with the cleanliness of the finished load. I was told by the repairman that future calls regarding unclean clothes would cost me despite a warranty that I purchased from Lowes.He suggested that I wash on using the Bulky Items setting and with a specific laundry soap. The setting provides more water but without the agitator, my clothing turns into a huge knot and comes out of the machine dingy despite washing loads for over 60 minutes at a time. My electric bill has gone up because I have to also add an extra rinse. The machine frequently become unbalanced. My dryers seal started loosening up two years after my purchase and finally became twisted in a sheet and ripped itself loose. Whirlpool has lost all future business with me.

I am so disappointed with this washer. I totally dread doing laundry. The following are the complaints: Every load comes out totally twisted and wrinkled!! The soap/fabric dispenser holds water after each load (I have to take paper towels and get the dispenser empty!!!). There is not enough water to properly clean the clothes. I have never noticed a reduction in my water bill and have had this piece of junk since 4-25-13. There is NO short cycle on this junk machine. There is an odor to my towels - like they are musty - after I dry them and use them. I use Tide HE detergent and clean the washer with Affresh (you shouldnt have to clean a washer). I should have taken the time to write a review much sooner, but decided today was the day after doing laundry. DO NOT BUY THIS WASHER.

I purchased a range and refrigerator from Whirlpool and have had nothing but problems with them ever since. Ive only had the range for years and (2) of the top burners are no longer working. Again, the refrigerator is only 5 years old and its handle has broken 5 times. I have needed to replace the handle every year that Ive owned the refrigerator. Whirlpool only offered a (1) years warranty for these faulty appliances and then immediately started to bug me about purchasing an extended warranty. I guess they knew that their junk would hold up, so they started pushing a warranty. Finally, their customer service while apologetic, are very robotic and appeared to have heard my complaint before. So, SAVE YOURSELF SOME AGGRAVATION AND PURCHASE ANOTHER BRAND. For if you dont heed my warning just know that youve been warned.

I have a Whirlpool top-loading washing machine model 3LA5580XSW3. The timer switch is not working and I have been told that spares are not available. Is this true? Everything else works well. Please advise as I really need a new timer.

The beat goes on. My Cabrio washer is still down. After working for a mere 14 months, the control board died, and the machine would not spin out water. The repairman ordered a new one. Though the part arrived several days earlier than predicted, the repair service said they could not send anyone out, until our scheduled appointment. At last, today, the repairman arrived. I am ready to start whittling down the mountains of laundry we have stuffed in every closet. Some areas of my house are starting to smell like a locker room. It is not convenient for us to haul everything to a laundromat, or impose on a relative who lives nearby.The repairman was in the laundry room for at least 45 minutes, and then very apologetically tells us that the part is bad. It will not work at all. He has ordered a new one, and requested rush service, which I think they will ignore. I cant help but think these parts are manufactured somewhere outside the USA. Well, listen to this Whirlpool, I would rather pay $25 more for this part, and have your washing machine work. Dirty laundry might seem unimportant to you. It is not unimportant to us! If you cant do better than this, make something else. I am furious, and will spread this news to everyone I know, and I will report on this situation again.

My side-by-side lasted 2 years 3 months. It stopped cooling. Lost all my food. Inconvenienced by waiting for repair service. Had to take a vacation day from work. This refrigerator replaced a 13 yr old GE and the one in my garage is 25+ years old and still going strong. No help from Whirlpool or Lowes. I will never own a Whirlpool anything ever again.

In 2008 I bought a Whirlpool range from Lowes. About a year ago I began to notice an electrical smell when I would use the oven. I called the repairman in October and he had to replace wires that had melted. The first time using the oven blew a fuse. Repairman came back replaced everything for free and it has worked fine since October. 2 days ago the fuse blew again. When I flipped the breaker in order to use the cooktop there was an arc flash which blew a hole through the back of the panel on the stove where the cord is hooked to the stove and a hole burned in my wall. After reading Whirlpools fan mail I see that there are severe issues with the quality of Whirlpool products. It is a sad day when the names we have come to trust are more concerned with the bottom dollar than with customer satisfaction with their product.

In May of 2010, my husband and I purchased a Cabrio washing machine. By the fall of 2010, I had put in a call to Whirlpool due to the washing machine chewing holes into clothing and not cleaning the clothes. Some of the clothes would come out of the washing machine with dry spots on them. Whirlpool sent out two different servicemen and even though one of them replaced the agitator we have still had problems with it. One of the servicemen even tried to tell me it wasnt the machine but it was my detergent (I use HE Purex dye free). I was told by a service rep at Whirlpool that there was nothing more they could do and I would just have to deal with it. I understand that products go faulty but with good customer service these issues could be resolved. Whirlpool obviously has little regard for their customers. I have contacted the Better Business Bureau. Hopefully they can get results.

Oftentimes when we take out the dark loads there is a white line left. It appears to be detergent that does not go into suspension. We are using HD. Just lately we switch to liquid. Question in our minds is if it does not move the water enough to put the detergent in suspension, how in the world is it even cleaning? I do not see the turnover of the clothes. Where is the quality control with this?

My son bought a Mastermind 250-L refrigerator on 09.09.2009 (invoice no. **) from the Good Morning store in Alleppey (phone no. 0477-23253809). The cooling effect was lost with a loud sound. I requested customer care. Three times, four people came and they gave a receipt of RS 890. After they left, it is in the same condition. I requested so many times, but there’s no reaction. Before I could go for legal proceedings, I would like to make you aware of the conditions prevailing in Kerala in sales and services. The young trainees who dont know to repair have broken down the entire system and it is fully collapsed. The franchise office washed their hands. This will spoil the entire name and fame of the company. Kindly look in to the matter and do the needful immediately.

Purchased a Whirlpool Cabrio Washer 5 years ago because our other washer died after coming home from vacation. Its just 2 people in this household so I dont do mountains of laundry. The other machine lasted 15 years so go figure. We purchased the Cabrio from Lowes. Got the extended warranty but as it goes the machine fails when all warranties expires. Over the last couple of weeks this machine started to not complete a wash cycle. All lights go off except for spin light and machine stops. Even asked the person in charge of washers and dryers at Lowes about this who then told me to get an extension cord and plug it into a different outlet. Seriously! I have had to unplug the machine after it fails to complete cycle, wait 5 minutes or so, plug it back in, select rinse and spin, it fails again 13 minutes left in cycle, unplug again, plug it back in, select drain and spin, wait for it to MAYBE complete that cycle. Do not purchase this type of machine. Just for a technician to come look at it is $100 or more and to replace whatever circuit board is probably another $300 or more. Screw that! Going to find a good old fashion one if possible. Piece of junk. Not going to spend $700 or $1000 just to wash clothes for 2 people.

I purchased a new Whirlpool washer and dryer (model number WED9250WR0 #WFW9250WR00). The washer broke after about 2 months. They took my washer and gave me some off brand one, because I purchased a 5 year extended warranty. They kept my washer for over 3 months, saying that the manufacturer takes that long to get the parts in. Its ridiculous! The tub, seal, and some other parts had to be replaced. It was shredding my clothing and my bedding. The first time they fixed it, a couple days later, it started making a horrible noise. The repairman came out, and a part had fallen off inside, so he put it back on. It kept happening, so I called them back, and he taped the part on!About 2 months later, the seal started shredding, and so did my clothing. I called again, and they had to replace the seal again. It still sounds off balance, and they said that was normal, because of the give in the floor. The day they fixed the seal, I washed a childs sleeping bag, and it shredded it too! I called again, and they refused to replace it, and they want to come and look at it again. My dryer lint trap seal also keeps coming apart, and I have gone through 3 of those in less than 8 months. They said they are just made poorly, so it will keep happening. I just want my money back, and buy a different washer and dryer somewhere else. I had an old pair that I bought, used, and they lasted me 5 years with less problems than these that I paid two grand for.

Another load of darks with white soap residue splattered across every item. Despite using a soap pod and setting to so-called Deep Water wash. Whirlpool top load WTW5000 is a terrible machine. As in other reviews, constant soap residue and clothes stretched and tangled into a compressed wad with deep wrinkles as you try and untangle them after the wash. Unable to dilute your soap and faking out the machine to get a bit more water are recurrent themes. Just ridiculous. There should be a class action suit for replacement. The customer service is useless and terrible - actually - there is probably nothing they can say and no answer or fix for this horrible machine.

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.