Purchased our hot water heater in August of 2011. About 3 days ago, it just stopped working. Surely it should last longer than this, right? Nope apparently I was taken! We called the manufacturer and described the issue. They said it was the thermopile. They could send us another out in a few days but we didnt want to wait so we paid $50 for a new one we were able to locate at a hardware store. Nobody sells these! We replaced the thermopile but no results... Pilot will not stay lit. Called Whirlpool back and they said to hit the reset button which we did. Called a technician (several) which wouldnt touch the heater. Said nobody works on these because they are riddled with issues. I pleaded with him to test it which he did. He said the control box is out! He said to cut our losses and buy a new one! I am so very upset! I cant afford another one! We called Whirlpool back again to see what they would say this time - they are sending us another control box! After reading all of the complaints and being without hot water, I am not hopeful of a good result! I plan on replacing the control box that they send and then saving for a new heater! I want my money back which Ive heard just wont happen! I have also had nothing but issues with my gas stove made by Whirlpool ever since it was only 6 months old. STAY AWAY FROM WHIRLPOOL PRODUCTS!! Run!!!

Since there is only two people in this home, we decided to go for the smaller front-loading machine. This was purchased in 2012, still running. It does a clean wash, however common sense does remind people to not over-load a front load washer. If one follows directions, it gets the job done, and ones machine lasts longer without problems. Thanks.

This Whirlpool refrigerator/freezer Model W10314956B was purchased from Lowes on June 29, 2012. Recently noticed rust appearing under ice/water dispenser tray. Requested warranty service, but was told the problem was considered DUE TO WEAR & TEAR! TOTAL COP-OUT! There are NO MOVING PARTS in this area; how can there be WEAR and TEAR? To my mind, this can only be charged as SHODDY MANUFACTURING or INADEQUATE QUALITY CONTROL by the manufacturer.This appliance is only 6 1/2 years old! Consumers expect refrigerators to last much longer than that. The only possible cause for this problem is as stated above: poor quality control by the manufacturing plant, and I completely discount being told the problem was due to WEAR and TEAR! I will think long and hard before I ever even CONSIDER purchasing another Whirlpool product, and maybe YOU SHOULD TOO!One issue that keeps gnawing at me is HOW, since this is supposed to be a STAINLESS STEEL refrigerator, can it rust? The best answer I found on Google was that its likely due to insufficient chromium in the mixture of metals used to make stainless steel. To me this continues to point to shoddy workmanship at the manufacturing plant. I have pictures of the problem, but for some reason Im unable to copy them to this complaint. Probably because Whirlpool is afraid of pictures that confirm their shoddy craftsmanship!

My dog is afraid to be anywhere near my Whirlpool side by side fridge. It makes horrible noises every 15 minutes to half an hour. I have to coax her to even let me escort her past. It has been snap crackling pop for several weeks and is getting louder with thumps and clangs. It does sound like the devil inside. Appears to be coming from the freezer side.I do not have the ice maker hooked up . It is plumbed for an ice maker but the servicemen who delivered it advised me they didnt do that . I didnt have the money to hire a plumber. The fridge was a PG& Energy Partners project in which those of certain age and income levels were presented new energy savers in exchange for old ones.Wish Id have kept the old one, especially after reading comments here. A senior, I live by myself in a fairly isolated area. I wonder now if the noise means a fire or electrical problem is imminent. My model number: ED2KVE*V*O, ED2FHE*V*O*

Ice maker kept freezing up. Im continually taking the ice tray out to unfreeze. The frequent removal of the tray eventually broke the tab off on the liner. Ive now been told this (liner) is not a replaceable part and since that is the case, the warranty will not cover. Im upset that the repair technician did not process the claim properly and state that the make had a problem freezing. What kind of company would manufacture a product that would have parts that are unrepairable? You spend close to $2,000 on a refrigerator, wouldnt you think you would have an ice maker that works? I know they hope to sell more appliances this way but you can bet I will not be purchasing another Whirlpool anything! I will also be retracting my recommendations to friends and family to purchase a Whirlpool. The company does not stand behind its products.

Bought this washer in May of 2019: Whirlpool - Whirlpool - 4.5 Cu. Ft. 37-Cycle High-Efficiency Front-Loading Washer with Steam and Load & Go™ XL Dispenser - Chrome Shadow. Model: WFW6620HC. SKU: 6313774. Paid over $1,000.00 for it. FIRST TIME washing our sheets, we had snags & rips. I immediately called and was referred to Whirlpool and then referred to an outside repair company. They sent a technician out who said everything was functioning properly despite having ruined 3 sets of sheets (these were not all washed at the same time & I didn’t realize they were being snagged until making the beds).I continued to use the washer - clothes were fine, but yet again, MORE sheets and now comforters RUINED!!!! I called YET AGAIN after troubleshooting the problem myself and finding that the drain holes in the drum had metal pieces sticking up causing the items to snag & rip. Another day taken off work to stay home for the repair. The repair guy comes out, the part was broken. So now I’m left once again with a faulty washing machine AND no ETA on when the new part will arrive and be installed AND having to take yet another day off work.7 sheet sets, 3 comforters, multiple shirts, & multiple bathing suits RUINED & was told there was ‘nothing they could do!’ I will NEVER EVER AGAIN purchase anything with the Whirlpool logo. It’s JUNK! Just an FYI, this was initiated in May of 2019 and it is now the middle of September 2019 with no fix updates. Who can go months without doing laundry???? Once again, poor customer service and JUNK of a product!

I purchased a Whirlpool microwave at the end of November 2015. Since then it has needed repair 3 times. Now I am being told it is not repairable. Microwave is only 1.5 years old and Whirlpool would not stand behind its product and provide additional warranty service or even a discount toward a new one. When I asked to speak with a supervisor I was just left on hold, 20 minutes later I hung up! Poor customer service!

In October 2009, I purchased a Whirlpool Energy smart gas water heater with flame lock safety system.$509.00 I had it installed on 5/4/2009 by Westmoreland Affordable Plumbing, $218.00. On 10/15 called Whirlpool stating that the upper thermistor was coding as a failure. They sent me another one to replace it on 10/19/2009. On 10/19/2009, 1 and 1/2 hours later, the tank was coding a bad gas valve, called back and told Whirlpool what had happened and that I smelled gas. I shut off the gas to the water heater and waited for a valve replacement to arrive. On 10/21/2009 I had E.H. Plumbing to install the new gas valve to the water heater, $150.00. On 10/28/2009 the new gas valve went bad. I contacted Whirlpool and argued with them until I had them replace the hot water tank. With their approval I went to Lowes and tried to get the same water tank but they no longer sold that model anymore. I was given their equivalent to the one I had purchased earlier. I had it installed on 10/29/2009, $150.00. I now see a class action suit was filed against Whirlpool for the model in 2008. They were still selling this model after the lawsuit???? I spent $1027.00 for a $509 hot water tank and a lot a days without any hot water. I have all my receipts and returned codes for this transaction. Is it possible to get my $300.00 back (for two extra installations) as a result of this problem? I also kept the old gas valve thermostat.

Horrible. We purchased the set In October 2010. It worked great for a little over a year. (Go figure, just out of the manufacturers warranty.) The washer stopped spinning out water. Every other cycle completes successfully. The diagnostic cycle is also successful but once there is clothes in the machine, it wont spin. I called customer service and was told that a one year warranty was $230 and service is $130 plus parts. After reading another horror story, it seems that this venture is going to cost us around $450 for a new circuit board. Where is that class action suit at again?

I purchased a Whirlpool Cabrio and a one year extended warranty two years ago. As soon as my warranty ended, my washer started to malfunction. I recently started to receive the F-51 code and the washer shuts down at the spin cycle. I am angry because I spent just under 1200 dollars on a washer a little bit over two years ago and now, it is sitting in my laundry room taking up space. When I called Whirlpool, they told me I could purchase another repair warranty for $316.94, which would take the cost over 1500 dollars for this washer and there was no empathy nor compassion for what I was feeling as a consumer from the customer service rep. I spent my hard-earned money on major appliance purchase and I think that it is only fair that I get more than a two year usage out of machine that was designed to last at least six years according to their website. There is no way that this should just be my lost and cost me additional funds.

My Whirlpool has all basic features and works for household jobs. It is extremely useful for routines like towels and clothing. It also works gently enough to launder curtains and goose downquilts. Operations are very simple and the controls make it very simple.

3 months after I got the fridge, the ice maker went out. 3 months later it started to work again. Replace the water filters 2 times per yr. It is noisy when it makes ice.

Some years ago I bought a whirlpool water heater from Lowes and the thermocouple went out. No big deal, so I thought. I went to Lowes, picked up a new one and tried to replace it. It wouldnt thread even though the package stated it was for my model. I went back to Lowes and they gave me another one, same problem. So I called Whirlpool, they said it was a left handed thread and they discontinued it, but they could send me a conversion kit at my cost. So at that point I was 2 wks out so I paid for the kit. I received the same thing I bought from Lowes. I was so frustrated I ripped the thing out and got a new one. That was 2 yrs ago and now I am having the same problem. I called whirlpool and they want me to pay for the replacement part. Mind you, the heater has a 6-yr warranty. I went to Lowes and they wont replace it. They sell items that they dont stand behind. I will never buy another whirlpool item and I will never shop at Lowes again.

Purchased Whirlpool Washer Mod# WTW57ESV1 12/9/2011. Washers transmission blew on 1/20/2012. Requested Whirlpool replacement. No results. Will never purchase Whirlpool products again.

We bought the dishwasher because ours was not a very good quality, and it was a Whirlpool and was larger than our old one. But the arrangement of the bottom shelf doesnt allow for effective placement of larger items. If you wash any large items it doesnt wash the top shelf dishes.

NU40T61-403 have had problems since day one. First problem was while heating up would make loud humming noise. Whirlpool sent out plumber. He adjusted plate under tank. That worked for about 2 months. Then pilot started going out. They send same plumber out again, also sent replacement part. Problem was fixed however about 2 months after that started leaking and flooding our garage. Called company again, was told that is no longer under warranty and stated we need a thermal expansion tank. I stated “why would we need this? This unit is only a little over a year old. Im not going to purchase another tank. A water heater should not overheat like this.” Long story short my husband has been burnt severely from the pressure build up as he was out in our garage walking past the tank when it decided to release pressure even though no water was being used at that time. He ended up at the ER with 2nd-3rd degree burns. I called Whirlpool again and was only told we need to install the expansion tank. Im so unhappy with this product I will never buy anything made by whirlpool again.....

Cabrio washer bought 5 or 6 years ago. Started a whining noise when spinning, so loud we close the washroom door to hear the TV. Called service, they immediately knew that the main bearing was going out & quoted the two parts needed to fix THAT COSTS MORE THAN THE MACHINE DID NEW! Labor was not included. Was also told that it will eventually start leaking. Piece of junk. What happened to simple washers that did a good job washing in half the time that lasted 15 to 20 years???

I had bought from S C Shah & Co, Mylapore a Whirlpool ac 1 ton split magicool dlx cop in March 2016 and installed in March 29 2016 by Cool Control System, kodambakkam From the installation period we had a cooling issue and informed Shah & Co, Mylapore where we bought the ac. They came and checked and informed Whirlpool customer care. Within two months i.e. in May 2016 of installation Whirlpool again uploaded/charged the gas (the service engineers told us this is due to hot summer). Though again we had a cooling issue, we were under the impression as this is due to summer as explained by the technician. After that rainy season came and we didnt use the ac.As we are in December when we complained Whirlpool they said this is due to the copper wire gas is leaking and it has to be replaced and informed that though under WARRANTY, the customer has to pay for replacement (we have used only the 3 mtr copper wire which came with the ac only. we have not used any our own copper wire). Whether WHIRLPOOL GIVES SUCH A QUALITY COPPER WIRE which has to be replaced within 9 months. Now they are informing that you are calling us after 6 months of gas charging, so we cannot service. If you could have called within 3 months we could have serviced you. BUT WE ARE UNDER WARRANTY. NOT EVEN AN YEAR FROM THE DATE OF PURCHASE.Not responding to calls, disconnecting to the calls even if we call their Delhi number 011-49308500. Though under warranty they are not ready to do service and very rude saying, we cant do anything. So, if we buy WHIRLPOOL ac we have to beg them even for their technicians to visit our place. Or we have to do our own service EVEN UNDER WARRANTY. Their local toll free customer care numbers/service executives always give a recorded message saying they cannot service. SUCH A PATHETIC SERVICE.

I purchased a Whirlpool fridge in September of 2015. In March of 2016 I noticed the Fridge portion was getting too cold. By April 2016 the freezer stopped freezing and fridge started warming up. I reported the issue to Whirlpool and made an appointment. The day of the appointment the first company called and their tech couldnt make it because of a family emergency. They sent another company out instead. That company diagnosed the issue as a faulty chiller and ordered the part and told me they would be in touch. A week goes by with no working fridge and I call them. They say it will be another week for the parts. Two weeks go by - no call. I call them and they say they have the parts and I make an appointment.The day of the appointment I call them to find out what time they will be out and they tell me they dont have all the parts. And when I mention that I have been without a fridge and that I am frustrated that they arent calling me and that I am having to call them back the lady starts yelling at me asking me if I want to cancel my appointment. So I call Whirlpool and ask for another company. They send a company out that is not trained to be working on a sealed unit. So I call Whirlpool back again and they send an in house tech out three days later. This is over about a month without a fridge at this point. Their tech simply recharges the system and says that it should be fine.A week later the freezer stops freezing and the fridge warms up to the point that both are not usable. The tech comes out and diagnoses that there it is most likely the chiller because of a build up of frost in the freezer. Orders the part and a week and a bit later I call Whirlpool up to get an ETA on the parts. They say they have the parts now (no call??) and they schedule an appointment. The tech comes out and puts the part in almost a week later (2 months now) and says that it is still building up frost in an area that it shouldnt and calls tech support back and forth for the next two hours. He leaves saying give it some time to see if it works, but admits to me that it is likely it is leaking in an area that he cant access.So I call up Whirlpool and explain the situation and ask for a new Fridge. It has been two months and the tech by his own admission could not say he fixed the problem and thought the problem maybe somewhere else. After looking at my case and me being on hold back and forth for about a half hour the supervisor says that at this time I need to wait to see if it fails again. And that if it does I need to have a tech back on site to verify. So this will be the seventh time I took time off work, it will be the fourth time the fridge fails and that I will have to throw out groceries. When is enough enough. I am into this now for almost double what the fridge is worth in lost wages and groceries.Do yourself a favour and stay away from Whirlpool!!! If I have to guess the following will happen: five days from now the fridge will stop working again (when the Freon leaks out - same timeline as previously) and then I have to call for a tech (3-4 days) and the tech will come out, determine that it isnt working. I have another conversation with a supervisor asking for a new fridge and they miraculously agree (yeah I know). Then what two weeks, a month... before I get a new fridge. I anticipate that I will have been without a fridge for 3 months before it is all resolved. Ridiculous is all I can say. Whirlpool should be embarrassed.

Whirlpool fridge with ice and water dispenser that broke down within days of install. The water dispenser stopped working after the first flush and Whirlpool were notified. They engaged a useless repair company who have been unable to resolve the problem and will not communicate updates. Whirlpool have been fully informed of the problem with their brand new product which was defective practically from the start and have washed their hands of any involvement in resolving the problem with their appliance. They defer defective product as a warranty issue and leave the consumer to chase after people to get a repair done. For a brand new $3,700 fridge that doesnt work within a week of install I just cannot believe they would sell a defective item and make their consumer suffer for it.What consumer would knowingly choose to purchase a defective appliance? If you end up getting a defect, the company should make it right....right away. Im at 2 months now without a functioning water dispenser on a fridge that is only 2 months old. Just disgusting.

I installed my new water heater in 2012. Within 3 months, it was not producing hot water. When I called, a helpful person at the Whirlpool warranty line told me it was because there was too much cold water being mixed into the hot water coming from the tank. I hung up... Called again and was told that they would be able to get someone in 2 weeks out to my house to check it. I told them that was not acceptable. I hung up... I called Lowes, where I bought it. The person on the other line finally, after more than 1 hour, was able to get a repair person out there within 2 days. I had to pay the fee to have the guy come look at my hot water tank, and tell me that he hated Whirlpools. He called Whirlpool, 3 times; he was hung up on 2 times. He explained what had happened was I had a hot water leak, that it probably it was overloaded, the thermostat control everything else was fine. However, that I had installed the heater myself not a professional. Therefore it was not up to NATIONAL code; therefore, Whirlpool refused to honor the warranty. So, short version, in order to get the tank repaired, I was supposed to spend an additional $300-$400 to bring the heater up to code for them to honor the warranty. What you ask made my heater out of code? It is outside in my utility room, and the flue was cut to fit and the OUTSIDE vent pipe was not above the roofline. It didnt matter that it is not in an enclosed space, that this was nothing to do with the reasoning the thermocouple went out.I simply turned up the heat, so far so good. Will I ever buy another Whirlpool? No. I have a Whirlpool fridge bought before the hot water tank situation. The ice maker went out within 6 months of purchase. When I called to have it repaired, the service guy stated he hates Whirlpool. The piece he had to replace was plastic that was replaced with a metal piece that should have been metal to begin with.

We bought our Terrorpool Whirlpool refrigerator in 2006. We have had problems with the ice dispenser, bad motor replacement, and now we have cracks all down the right inside wall. I had bought an extended warranty of four years at the time of purchase which covered the cost of the previous problems. But it has now expired, and I was told it would be my expense for repair. What happened to reliable appliances that our parents and grandparents had? What happened to the name Whirlpool? I will never buy a Whirlpool product again, not to mention the customer service (which I wont mention). If you have model # ED5PHEXRQ00, please write about any problems you have had and help someone else not make the same mistake.

We bought the Cabrio less than 5 years ago. First of all, a high-efficiency washer should not require an extra rinse after each wash, but this one does. I cant see how thats being efficient. The washer, even for a small load, can take up to 54 minutes, and then when you tack on an extra rinse, its well over an hour, so what you may be saving in water, youre spending in electric and wait time. And then, there is still a soap/water scum left on the clothes, which is only evident on the darker clothing. Now, just recently, the washer is stopping, and NOT unlocking after about a minute into the start cycle. I will have to cancel the wash, turn it off and unplug it before I can get it opened. Im sure its something to do with the electric panel, which after reading the reviews, we are not going to fix, and we are headed out to buy the traditional top loader, NOT high efficiency, which I suspect will still be more efficient than the Cabrio.

We bought a WRS325FDAM02 Side by Side Whirlpool Refrigerator and from day 1 we have been having problems with rust buildup on both doors. Bought it in July 2014 and have had the service people over to figure out the problem many times. They finally decided to replace the doors which didnt help because the replacement doors are doing the same thing. We have bought everything they told us to buy to clean and try and prevent the rust from coming back but nothing helps. Our warranty was ready to expire so we bought the extended warranty only to find out that cosmetic issues are not covered under the extended warranty plan... Stay away from this model refrigerator... Not only that we were then told the doors are not really Stainless Steel just some fake crap that looks like Stainless Steel. We paid good money for this refrigerator and have to deal with cleaning rust off the doors day after day.

I have had this Whirpool Cabrio washer now for one year. Clothes always come out wrinkled (even after drying). It leaves clothes unclean and leaves white streaks in clothes. Water level is so low in, that it cannot rinse or wash clothes properly. After washing towels, when removed to put in the dryer, soap is left in towels. I have had a repairman here, he says the design is bad, yet reports works as designed. Dont buy this washer. This is a piece of junk!

Although we live in Canada, we purchased our slide-in oven at Sears Roebuck in Buffalo, NY only because of the size availability only in the US (actually, the unit was manufactured in Canada as we found out later!). Obviously, this created another problem since the unit was not underwritten by Canadian Electric codes, Sears Canada repair would not touch it! Once installed, it worked great until the first problem with the oven quitting after self-cleaning. It is the second time in 3 years that both the thermostat and the sensor went in this RBS245 slide-in oven. Once the self-clean cycle completes (quite smelly!) and cools, the oven does not operate rendering the oven useless. First time, in 2009, Sears repair only suggested (since they would not do repair on it for reasons stated above) which parts could be faulty: Timer, sensor, thermostat or elements. It was thought to be the electronic timer unit, which was replaced at a $215 (needlessly) because that was OK. Both thermostat and sensor cost $150. Even the elements were replaced, $52. The second time, just a week ago, exactly the same happened. I replaced the 2 items: Sensor and thermostat at a cost of $154 and the oven worked fine again. I called both Whirlpool US and Canada, but no one could/would give any answers why this happens.So far, it cost $600 in parts to repair! This is nonsense from a company that has had good reputation and record. Obviously, that is changing! If Whirlpool cannot engineer a product that works as they say it does, they should close the shop! Reading here, there are others who complained with the same problem. It is time for Whirlpool to come clean!

In 2011, I bought in Croatia, for the start, 2 washers (model 3LCHW9100WQ) and 1 dryer (model 3LCED9100WQ) and opened the first self-service laundry in Pula, Croatia. Since the beginning, I had problems with the gum (black). After the washing cycles, you could see black lines on the laundry. Whirlpool Croatia denied that the gum can be the cause. After two months, they gave me new gums, but the problem still exists. After 5 months of work, the first malfunction on the washers started. The biggest problem is that it took and still takes them up to a month to repair them. And these problems I have ever since. Also, the error codes never showed the correct malfunction code. In global, if I take that I have these washers and dryer for about a year, they were out of function for more than 3 months. The warranty expired in April 2012. On these reasons, I cannot recommend any product of Whirlpool, and I have to change to another company to buy more washers and dryers.

Whirlpool Dishwasher purchased at ABC Warehouse in Chesterfield, MI and was delivered on 10-2-2014, and one year later, we noticed that the tips of the lower basket were coming off. We contacted the holder of the extended warranty (5-yr.) and also Whirlpool. Both replied the fault was cosmetic and was not covered by warranty, that only mechanical/electrical components were covered. When we were buying the extended warranty, we were told that we were covered for all issues that may occur. We werent told cosmetic flaws were not covered. I guess consumers should, before buying a new product, make a specific list of possible problems, and make sure whats covered and not covered. We have been unable to resolve this issue.

Whirlpool refrigerator stopped working after two years of ownership. The back of the freezer compartment will ice up, stops cooling and makes a loud grinding noise. We expected a much longer life in a brand new refrigerator. Our extended warranty plan has not provided a replacement or comparable credit for a new refrigerator. We have been without a refrigerator for over a 1 1/2 months. Very unpleasant during the holiday season!!! I would never recommend buying a Whirlpool product of any kind.

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

Had a part come off right after our purchase but was a easy fix to repair. The silverware basket also kept coming off until we looked at it and realized it was on wrong. This dishwasher is much quieter than our last one. It also shows fingerprints. We got this dishwasher in a group purchase during a sale at Lowe’s that included the refrigerator a stove, microwave and this dishwasher.

I purchased a dishwasher and hooked it up. The reason I install products myself is I dont like people in my house. I dont know if they are there to help or inventory what they plan to rob from me later. It did not drain so I called Whirlpool who said that I probably hooked it up wrong. Whirlpool said that they would send a service man but if it was hooked up wrong I would have to pay for the service. The service man did arrive and had tattoos all over his neck and arms. (A tear drop would have confirmed that he was a murderer). The machine was hooked up correctly, the water pump was not working at all. The service company that Whirlpool contracted took 3 day to order the part. Yes three day to even order the part. Then another 10 days to get the part in. I called Whirlpool and they did not seem to care at all. My thought is, I am out $599 plus tax, and I have to wait 2 weeks to get my machine fixed, plus I have to take hours off work to wait for the service man and now I have to worry about the service man breaking into my house and robbing me and Whirlpool doesnt care. They should have to pay for the time I was off work and for the interest I lost on the money not being in my account during that two weeks. Whirlpool didnt care at all though. Worst customer service ever. Used to be that Made in America was something good. Not anymore thanks to companies like Whirlpool. Made in America = Garbage!!

I purchased this machine in April 2011. Adequate performance until this past fall. It did not drain properly and began to smell, then stopped working. I called a local certified repairman who discovered an item of clothing trapped beneath the basket blocking the drain pump. $109.00. Less than 2 months later it happened again. The repairman returned and again found a blocked drive shaft under the basket. $109.00. When it happened a third time I called the Whirlpool repair line. A serviceman was sent out and immediately knew what the problem was (prior experience). He removed the basket and once again there was an article of clothing under the basket, blocking the drain pump - $129.00. At this moment it is beginning to smell again. I spent 40 minutes on the phone this morning with Sears and Whirlpool. No help whatsoever. This machine is not even 3 years old. I never overload it and clean it regularly. I bought the washer and dryer as a set because they are quite visible in my home. I have had Whirlpool products for over 40 years and never had a problem. I need someone to stand behind this machine.

I purchased a Whirlpool Duet front-loading washing machine on September 27, 2010. By October of 2011, it was making a loud grinding noise during any spin cycle. I called for service and was told I needed new bearings which entailed rebuilding the machine. I had purchased a 5-year extended warranty. I was originally told by the warranty company they would replace the machine.After waiting two months, and after several contacts made by me to the retailers customer service, I was told the machine would not be replaced, but repaired. After the repair, on January 6, 2012, the machine now rattles and shakes so much during the final spin cycles. It is literally impossible to have a conversation with someone standing next to you in the same vicinity as the washer, it is that loud. I am sorely disappointed with the Whirlpool line of products and with the retailer who has been dragging their feet on customer satisfaction.

Everything I have read is what I am going through... First the clothes didnt come clean. Lint piles on everything dark... Then at 1 yr and 7 months old, the drum and spin mechanism breaks. It cost me $333 in labor... Should have cost me nothing as far as Im concerned. 2 weeks later, its putting a code up that the hot and cold lines are crossed. Nope, its the whole computer board. Whirlpool again said they will just pay for parts... piece of crap. I paid for the best... Sure didnt get it.

We purchased our refrigerator new in 2014. After only 4 years and taking meticulous care of our Whirlpool Top Mount Refrigerator, the temperature regulator stopped working - and the condenser fan rang constantly. The refrigerator couldnt get below 50, and the freezer vacillated between 17 and 30 degrees. We live in a somewhat remote area and could not find an appliance repair person to look at it. So we had to purchase a new appliance. Needless to say we did not choose Whirlpool!

The machine pass all the cycles but the clothes are only very wet and still dirty.

Purchased Whirlpool side by side June 2010. Within a few months realized major problem with ice maker. Reservoir on door would leak and freeze inside the door. Service man out at least twice, advised to maintain service contract as would continue to have issues. It still leaks, freezes up and does not dispense properly. Now the inside liner of the refrigerator is cracking and neither the warranty company nor the WHIRLPOOL Manufacture Co. will stand by their product. It is my intent to warn as many people as possible, so they will not have the same bad experiences.

I bought a Cabrio washer in 2009. I started receiving the infamous F51 code. When I called Whirlpool, they refused to even acknowledge that there is a problem with this washer. When I brought up the pages and pages of complaints about it, they acted like they did not exist. I hope this review will deter people from purchasing one of these faulty products!

We purchased a Whirlpool Energy Smart Electric Hot Water Heater with a 12-year warranty from Lowes on August 30, 2010. The water heater stopped working and the green light was flashing three times. We contacted Whirlpool since it was less than two years old and they were very rude to us. They told us it was the sensors and we would have to change them out. We waited while they sent the sensors to us. We installed them and it still would not work. It continued to flash three times just as before. We contacted Lowes where we purchased it and they were extremely apologetic and said they would be glad to replace it if we could get an RA number from Whirlpool, but that many others have been having a hard time dealing with Whirlpool. We contacted the rude people at Whirlpool again. They said they were not surprised that the sensors did not fix it. We asked for an RA number so we could get a replacement (after all, it did have a 12-year warranty). Now we were days later with still no hot water. Now this rude technician said it was probably the control board. I asked him if we were going to have to be without hot water until we changed every part on the unit. At this point, we just took the hot water heater out, put it on the curb, and went and purchased a different brand. Whirlpool has lost us as customers for life. If their other products are as horrible as that hot water heater, I wouldnt take any if they paid me to. They were by far the rudest and most hateful people we have ever dealt with and life is too short to be treated that way. I predict they will be out of business in no time with the garbage they are putting out.

I Purchased a Whirlpool range with self cleaning. I do not recommend anyone to purchase these ranges. The self-cleaning does not work at all. Like numerous reviews that said you can run them several times to do the self cleaning and they do not clean at all. Save your money. Do not purchase a whirlpool appliance!

I bought a Whirlpool Cambrio washer/dryer set last year. I hate them. They dont get the clothes clean, let alone wet! I couldnt believe it! I put my grandsons bib in the wash and it came out completely dry with the stuck on food still there. My husbands shirts still smell like the cologne he put on! I asked a Home Depot sales person about this and he says, yeah, we hear that a lot. !!!!!!! Im going back to a washer with an agitator so that I know my clothes are being cleaned. This whole water control business is insane. Whats the point if you have to wash the clothes several times to feel like they are marginally clean? The problem is that the industry has decreased the amount of models that still have an agitator so my selection is very slim. First and LAST time I ever buy Whirlpool.

I bought this washer thinking it would last me for a long time. And now it wont wring out my clothes and I just wanted to say I am disappointed in my Cabrio Washer.

I have double door Whirlpool refrigerator 1.3 years old. Since last 1.5 month I face problem. 4-5 times their technicians done visit. Following observations done by them: 1st visit problem - Water run away from back side bucket. Solution - Due to atmosphere moisture. 2nd Visit - Cooling fan not working. After 2nd visit refrigerator not worked. 3rd visit - Compressor fail. 4th visit - replace compressor. After replacement, refrigerator outer surface become heated. Skin will burn if anybody touch refrigerator. Problem still continue... I pay 2000 rs to Whirlpool as per companys norms. I lost my frozen, milk, veg., fruits etc. of approximate 1000 rs.

We bought 2 Whirlpool refrigerators for our new home 5 years ago. The first ice maker died 2 years ago at 3 years old. The second has now died this month. We called the repairman in who told us that Whirlpool knew there was a problem with their ice makers, but because they did not cause fires, they were not recalled. We paid $480 later for items that should last at least 10 years, not 3-5 years. We will never purchase another Whirlpool appliance and neither will any our family. A company with this level of ethical behavior that knows they have a faulty piece of equipment and just chooses to do nothing does not warrant my business.

I have always had Whirlpool Everything - not anymore!!!! I purchased a water saver washer that I am very unhappy with - it does not get the clothes clean. I have to put it on an extra rinse (water saver?) to get the soap out. I use the Tide for HE washers. I cannot wash a large load in it - directions say I can. Anything too heavy or bulky will not spin out well. Will bounce all over the place. From now on I will switch to another brand. They push so hard to buy a warranty because they know you will have trouble! Should have read the reviews!!

Whirlpool gas range convection oven - I have only had this range for 2 weeks. Manual is sketchy to say the least. Purchased from LOWES - salesman were not well-informed. I have had to do a chat to find out information. Range looks great but performs poorly. Takes a while to heat anything even on high and on large burners. Grates are too heavy. I am sorry I did not see the editor review before I purchased. I have not used the convection so I cannot speak to this but my choices were limited when I purchased and I did not want a convection oven and other ranges would not purposeful for my use.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

I bought it 1 week 1/2 ago and cannot wash correctly the clothes in it, have to rewash 2 or 3 times and bedding? Forget it. Still is dirty. Water does not go over the clothes, it suck for the price I paid.

My Cabrio washing machine is 3 years old, and is working the way it has been designed to work. It does not clean clothes and it consistently has a foul odor. Due to the odor, I must use the cleaning cycle with Affresh (pricey product) 3-4 times weekly. Even that is insufficient. Because it is in an indoor laundry area, the odor permeates the hallway and nearby bedrooms. The extra cleaning cycles are contrary to the energy efficiency of the washer, and detrimental to the severe drought conditions in California. When I contacted Whirlpool about my situation, they recommended I substitute bleach for the Affresh to keep the cost down.

These washers are known to rust terribly from underneath the bleach dispenser. Please note that if not detected within the 1st twelve months from purchase, then Whirlpool will not stand behind their product. I would highly recommend not purchasing the Cabrio top load washer. Extremely dissatisfied with this product and warranty.

Even with the hottest water on the most heavy duty setting, regular dinner plates are not cleaned. The flatware holders that are set in the door (instead of free-standing in a rack) do not have adequate holes in the holders and are too far away from the limited jets to get adequate soap and water to cleanse the flatware. Even after rinsing all scraps off the plates and flatware, we find bits of food, gravy, or smudges on the plates and flatware - since its first usage. The manufacturer had the audacity to claim that was normal. Settings include delayed starting, heavy duty versus normal washing, and different types of drying. The heavy duty washing is definitely poor quality, and there seems to be no difference between any of the drying settings. The delayed start is nice. The physical layout of the prongs on the racks and the folding racks do not allow easy fit for most sizes of pots plus plates on the same bottom rack. I cannot put a 1 gallon pot level on the same rack as dinner plates. I must put it beside salad plates. Only small sauce pans fit neatly or cleanly beside dinner plates. Yet the external dimensions of this dishwasher are the same as the competitors standard size. Looks neat and is easy to clean. Also, the exterior does not show scratches. Actually, I cannot see where the exterior has any scratches. The service people were very little help. The Warranty said that after five (5) service calls the unit would be replaced. We made six (6) service calls, but we were told that we did NOT have six because if you called again within 90 days of a call, that was considered the same service call. That requires 450 days minimum to have five (5) qualified service calls, but that warranty was good for only 365 days!

This refrigerator was already part of the appliance package that came with the property. I dont think if I had a choice, I would choose this brand. The stainless steel finish has rust spots, the top shelf has cracked and it is less that 5 years old.

Purchase a brand new Whirlpool fridge at the Fry’s Electronic in 2017. Broke down in 2018 almost 1 year after. Called Whirlpool company for replacing a new one. They didn’t replace before they had sent out a certified technician for fixing 3 times. It took forever to fix it, and still had the same problem after months. Finally, they agreed to replace a new one. Now I still have the same problem with a newer one which they replaced it over a year ago (including fixing and placing time). Just called to the Whirlpool company today for fixing or replacing, spoke to rep Sara, she said that it’s no longer under warranty because it’s more than 1 year. I told her that because the company didn’t replace right away; therefore, it has been more than 1 year; but from the time they replaced it, it hasn’t been 1 year. Ill never buy any Whirlpool products again.

This washing machine has been nothing but a problem from the beginning. Theres always something wrong with it. Things that cost so much should last much longer than a couple of years! I have to clean out the drain about every 3rd time I use it or it wont spin out as well.

I bought a Whirlpool duet washer and dryer. These appliances are still under one-year warrantee. My washing machine was broken for four weeks, and they have been unable to receive all of the parts needed to repair it. They have made three appointments to fix the machine, telling me that they have the parts and only to cancel the appointment the night before. I have tried to get Pacific Sales to exchange the broken machine, but they will not do that or compensate in any way. This is a top of the line model; I would have been better off with a low-priced model, and I might actually have a machine that worked. Whirlpool supposedly had the parts on back order, which is not what Whirlpool informed me when I was able to reach them.

Does not get clothes clean. Period!! Takes just over 1hr. Noisy, lasted 3 1/2 years, transmission broke, take the warranty with a washer/dryer. Whirlpool was the top of the line, front loaders give less trouble, agitators clean better, go for the cheaper versions, our loaner Whirlpool, WTW4850H or WTW4950H washes quicker and cleaner than the Cabrio Energy Star.

Whirlpool Cabrio Washer WTW7800XW2 - After buying my American made washer..... at nearly $900 with extended warranty about 2 years ago. This week noticed small cracks in plastic that surrounds and holds glass lid. Now lid will not sit flat and glass is emerging from encasement. Called extended warranty claim center and was told it was a cosmetic issue. Called Whirlpool, and was told they were unaware of this flaw, even though countless websites, chat sites, and Youtube. My frustration is how they claim to be unaware of this flaw and refusal address it, after countless consumers have called. I would be willing to start a class action on this matter!

I purchased a Model WRF989SDAB01 Whirlpool refrigerator with the French doors and had it delivered in March 2014. The evaporator developed a refrigerant leak in May 2015. Whirlpool said it was not their problem since it was over a year since I bought it. The technician said this is a problem with this model. I am having it repaired under the extended warranty that I bought. One of my concerns is that the unit has two evaporators so the other one will probably start leaking any time. What a piece of junk. Dont buy Whirlpool. Their quality and service stinks!

Im a member of Costco. I trusted that they will sell me a decent refrigerator, wrong! I bought a French Door refrigerator by Whirlpool on March 2018. It freezes my food on the left compartment and on the middle compartment. I called since its under the one year warranty. They came 8 times already and changed parts and promised me every time they came that this will resolved the problem... still the same. I have been in the phone with Whirlpool for one hour and a half for 5 times and they still want to do more tests. I will never buy another Whirlpool unit again! Costco should be ashamed of selling this brand! And they should paid for this also.

We purchased a 4 piece set of Whirlpool kitchen appliances and have minor to major problems with 3 out of the 4. We had problems with our gas range/oven from the start. When I called to register the brand new range they told me it had been previously registered to someone else and they made me fax my receipt to them proving that the appliance was purchased new. Lowes said it was brand new in the box when I purchased it leading me to believe Whirlpool tried to pass off a refurbished product onto Lowes and then onto us. No surprise when the stove stopped working 3 times in barely over a year. It was so defective Lowes ended up replacing it for us. Not Whirlpool... they only argued with me about how the third time it was out of warranty and offered no help in fixing or replacing the defective oven. Now our ice maker just stopped dispensing ice 7 days after our warranty expired on our refrigerator model # WRS586FLDM00. Whirlpool will only agree to cover parts and is sticking us with the service call and labor! And thats not all... the plastic coating on the dishwasher racks started coming off exposing rusty metal when it was barely over a year old and I have received a postcard indicating there is a lawsuit involving our model for overheating and fire events! Now waiting for that to be our next issue. I am so disgusted with Whirlpool. We bought Whirlpool appliances believing they were quality products. They are quite the opposite. Wish I had researched their reputation and history of complaints before buying. Do not recommend Whirlpool Brand. Sincerely, Disgusted in California

It is a good refrigerator for the price, but it is not big enough for our family. It does get very cold in the refrigerator part unlike our last refrigerator. I only wish it had more shelf space on the door and the egg place fit more than 6 eggs.

Purchased model WRT311FZDMOO refrigerator on Aug. 6. Took 3 weeks for delivery. All 3 door bins for this refrigerator have cracked after less than 2 months. Called customer service. They say its wear and tear. And ask how many would I like to purchase. Looked online. Cost is 30.00 to 32.00 per bin. Cant put milk in the door bins. The cracks puncture the container. Poor quality plastic.

Whirlpool Cabria Washing Machine hold down switched failed in just 18 months of use. It took the Technician 5 days to serviced and repair our Whirlpool top loading washing machine. The washer is till acting up and stop working unless you put a weight on the top loader cover.

I wish to file a complaint regarding a Whirlpool flattop electric range that we purchased approximately eight years ago. After the first year, a residue began to build up behind the glass on the front of the oven door. Finally, about 18 months ago, I decided to try to unscrew the back of the door in order to clean this since it got increasingly worse year by year. When I unscrewed the door, the side metal bars broke off and the range is to say the least, looked very unappealing . When the oven self cleans it makes the outside of the oven brown and very unappealing.This is a Whirlpool Gold, Super Capacity 465 range. We have been dissatisfied from the beginning. This complaint is not about the retailer, it is about the Whirlpool product. Please help as I am quite dissatisfied with this Whirlpool product at this time.

Whirlpool Cabrio Washer - I have had my washer for about 4 years, paid $1,000.00 for the unit and now I am being told that the control board needs to be replaced and it will cost me anywhere between $300-$600 to fix it. My point is, a washer should last longer than 4 years especially if you paid good money for what I thought was a reputable brand.

I bought this washer (model WTW7800XW) on 12/23/2010. Never happy with its performance from the beginning. Within the first 18 months, the lid hinge completely rusted and broke. The repairman stated that the hinges and glass lid would need to be replaced at a cost of over $400. We paid $899 for the washer. Instead of paying that much, not knowing if it would only last another 18 months, we removed both hinges and removed the lid manually to use the washer. After complaining to Whirlpool about the problem, they thanked me for the info so they could use it for the future. The latest problem to arise is the light inside the washer. The mount for the light was made of steel and has completely rusted away, so the light is just hanging inside the washer. Whirlpool needs to step up and resolve the issue with an extended warranty for these machines.

Bought a Whirlpool Cabrio. Noticed it was getting really loud less than a year into owning it. Called while it was under warranty. The tech said it was fine. Within the next year and a half it got so loud, you cant hear anything else in the house while it is running. Now it is leaking from the tub seals and the bearings are going out according to two service techs I have had come look at it. They say it is more expensive to fix than the washer is even worth. This is due to the parts that would be used to fix it are the same cheap Whirlpool parts that were put in it in the first place. They both said that these are not good washers and commonly go out about a year and half to three years old. Shame on Whirlpool for making such a low quality product and not being willing to do anything about it.

I purchased GMH6185XVS microwave in Dec. 2011. It was installed in January 2012. This was for a remodel kitchen with all Whirlpool appliances. In August 2014, we discovered the micro would not heat. I called Whirlpool as directed by Sears. I am told I have to call a repair service and pay for it. I have a 14 year old Whirlpool in my home. We have never had a problem with it. I had a Whirlpool micro in my previous home; never a problem. This is a second home that we hardly ever use. We are two adults. My daughter had the same problem with the same microwave. I am very upset with Sears as well as Whirlpool. Even if I used this machine everyday, it should not break in 2.5 years. Shame on both Whirlpool and Sears. I will never purchase another Whirlpool product again. I will be telling everyone I know.

Whirlpool Cabrio Washer and Dryer - The washer does not stay balanced even with a very small load (even though advertised can wash King size comforter). Even with a light load, we have to put the dryer on Heavy Duty or Bulky...and usually have to dry a second time. When attempted to contact Whirlpool, no help available. WORST PRODUCT I HAVE EVER PURCHASED... Would not even want to GIVE this set to a friend or family member. DO NOT PURCHASE THIS PRODUCT.

Bought a Whirlpool refrigerator at Home Depot in 2018. It has been a $3,000 piece of junk!! Customer service is garbage!!! They refuse to address a persistent problem since the day we bought it. Do yourself a favor and buy another brand!!

This machine cannot handle washing jeans, towels, blankets, pillows or anything bulky or very small loads. The load becomes ul unbalanced almost every time I try to wash a load. It has never gotten things very clean.

My stove is good, I have gone through 2 refrigerators in less than 8 years and the replacement is having issues. Service is a joke, customer service is questionable but trying to assist but at this point will not recommend whirlpool products.

WTW8800YWO Whirlpool Cabrio washer, 4 yrs old! Replaced!!! Its a poor quality washer -- the bearings go out. I purchased this washer and matching dryer at Lowes following a house fire. I initially thought the water saver was a good feature. Unfortunately, my clothes were not clean and were covered with lint following each wash. I have had to replace the ring inside the washer due to shifting and causing water damage to the new flooring. I soon became disappointed with my purchase, but until the noise became so loud in the spin cycle and the repair exceeded the initial costs, I kept the washer. I am another consumer who would NEVER purchase nor recommend a Whirlpool W/D. The repairman said, If you want a washer built to last, buy a Speed Queen!

It seems the quality issue of the LED of the washer Whirlpool Cabrio. It was broken from the screw part of the glass and the plastic/alloy and the glass. They would charge me $416 to replace the LED but I rejected and was still required to pay $85 for labor fee. I called the company and they didnt admit that was a quality issue but I just found many consumers had the same problem. If someone would like to have a lawsuit, please contact me and I will join.

5 years and 11 months ago I bought a 50 gallon gas, Whirlpool hot water heater with a 6-year warranty from Lowes. The 2007 water heaters were on sale, so I paid $329 for it. Within 6 months, I replaced the gas valve, and a few months after that, the thermo-couple went out and I replace that. Each time I called Whirlpool and got return authorization numbers for the parts, I still ended up paying for the parts plus labor. A year after that, the igniter went out and I had that replaced. Last year (the day before Thanksgiving), the thermo-couple went out again and I had to have that replaced - and it cost me for the part plus the labor - even though I had a return authorization number. I also replaced the water line connections/hoses to the water heater at that time. The customer service rep for Whirlpool told me at that time if I had another problem with the water heater, they would replace it for free - and the warranty was good until Dec 31, 2013 (this year). NOTE: Every plumber that has come out to fix the water heater and replace the parts stated that they see a myriad of problems with Whirlpool water heaters. They said the parts like the thermo-couples, igniters, gas valves, etc are poorly built and they replace them all the time. On Christmas Eve 2013 (two days ago), the water heater started leaking from the top by the valves - and so much pressure had built up in the heater the new water hose connections burst, spewing water all over the heater closet. I called Whirlpool the day after Christmas (today). At first, they told me they would not replace the heater as it was not in warranty and then I told them what I was told by the service rep last year. She finally agreed that my heater is indeed under warranty and gave me a replacement authorization number but she told me my warranty did not cover labor. I called Lowes. At first, they told me I would have to remove the old hot water heater myself and bring it back to the store in order to get my replacement. I am a 59 year old woman and I take care of my brother, a disable veteran. Although I am in good shape and healthy, I dont have anyone to help me get the gas and water disconnected and help me lift it into my Suburban. The man at Lowes agreed to bring out the the replacement heater and pick up the old one at no charge, but I will still have to pay $299 plus the cost of new hoses to have it installed. By the time the replacement one is installed, I will have paid a little over $1200 for a $329 water heater. I could have installed a tankless one for that, but I cannot see spending that kind of money right after Christmas. If I have one issue with this replacement, I will install a tankless water heater - and it will not be made by Whirlpool or any of its affiliates. My recommendation would be to steer clear of Whirlpool and their products.

This Whirlpool Water heater was purchased through Lowes on March 29, 2011. This past weekend, water started leaking out of the thermostat/natural gas control located on the side of the tank. I called a plumber to take a look. He stated that a new thermostat/natural gas control was needed. Although the tank has a 12 year warranty, this item does not. Whirlpool did agree to replace the part but would charge me $30 to overnight the item which still would have taken 4 days because of a weekend. To install the item would have cost me almost $500.00.To purchase a new Rheem Water heater was $999. I chose the second choice as the first choice would have still left me with a subpar water heater obviously already out of warranty. The reason for my review is that I saw the number of complaints on the failure of this part. When I purchased this water heater, it was the better model due to the 12 year tank warranty. What use is the tank warranty when the other items dont last? There should be some type of reimbursement but Im not holding my breath. Please buy a contractor grade water heater and not the cheaper models.

Whirlpool Cabrio top loader washer - I am writing to really complain about a washer I bought there at Metro. The people were great BUT this washer has been a REAL DISAPPOINTMENT!!! It is only 4 years old and I have had to have them come and replace the top of the machine. It has rusted around where you put the bleach, the soap. It leaks underneath the machine, its rusting on the bottom of the machine horribly. SO DISAPPOINTED!!! We bought all WHIRLPOOL products - washer and dryer, stove, microwave, dishwasher.What is it with these things? They rust so easy. I had a washer before this one for 14 years and it never did this. I guess things are not made with the same quality as years ago, but I will not ever spend my hard earned money on WHIRLPOOL AGAIN!!! I guess I will have to put up with this machine till I can afford to buy something else. VERY DISAPPOINTED CUSTOMER!!!

I bought a washer dryer Cabrio set and the washer after 2 years has a bearing failure and is squealing badly. The service technician quoted $400.00 to fix a washer that cost me $800.00 new and is 2 years old. I had a Whirlpool washer and dryer set for 11 years with minimal issues and that is why I bought Whirlpool again. This will be the last time. It is a matter of time before the washer fails and I will have to purchase new or pay the service technician.

I purchased an appliance package Whirlpool Gold series that included a range, refrigerator and dishwasher. This was approximately 3 years ago. The range has already been replaced by Whirlpool after having it repaired twice and, finally, following the complete breakdown on Thanksgiving with turkey in oven. The refrigerator has broken twice and the computer box that controls all functions was replaced twice. The compressor goes off randomly and is currently off again at the moment. I woke up this morning to this and the temp inside is around 50 degrees. Needless to say the food inside is a loss. I will never purchase any Whirlpool appliance again. These were not inexpensive appliances by the way.

Every one of the knobs cracked where they engage the gas valve. One gas valve came loose from the manifold creating a gas leak discovered by the propane company on a system leak test. Screws came loose that hold the tracks to the base for the slide out bottom drawer. The AquaLift cleaning system is useless. Better buy some oven cleaner and rubber gloves. Very disappointed! One star because 0 isn’t an option.

Water heater purchased in 2011 and is already broken. Called the hotline and they were rude. Told me I need a $199 part. I read all the reviews and it seems that Whirlpool has made a bad name for themselves with the water heaters. They were not willing to work with me.

My whirlpool duet was extremely quiet the first few times I used it and seemed to work well. Then I noticed that it randomly drained the clothes but didnt spin them, it did it on different cycles, and I would have to run the load again on spin and drain, another 19 minutes of run time. After a week it began to make metal scrapping sounds on the spin cycle and vibrated to the point that it moved the pictures on my walls. I called Whirlpool customer service and they authorized a service call. In short, the service man was very confrontational told me there was nothing wrong and charged me $72. It still vibrates and randomly doesnt spin. But now after he took it apart it sounds like a jet engine when it does spin. Whirlpoolss response after repeated calls? Not a new machine, but another service call......

Two years ago, we purchased a Whirlpool Cabrio Washing Machine from Sears. All of a sudden, it was making sounds in the spin cycle that sounded like a jet airplane taking off. It was terribly loud. We called repair technician, which cost $90, only to find out that the bearing is gone and its going to cost over $500 to fix it. This is absolutely ridiculous! We expected it to last several years, only to find out that we would have to spend almost as much as the washer originally cost in order to fix it. We paid $700 for this machine, two years ago, and I can say that Ive never been more disappointed with a product in my life. My previous washer lasted thirteen years, not to mention my dryer and stove fifteen years, with minimal repairs. I will never buy another Whirlpool appliance again. I have read some other complaints on this consumer affairs website, as well as other sites, regarding this same washer with the same problem on the bearing and cost to repair. If anything, I think Whirlpool should make good on this product and offer something regarding a recall or payment for repair in some form. As far as Im concerned, I will alert everyone I know about Whirlpool appliances and advise them not to purchase it. Now, I either have to pay over $500 to repair my washer or go buy another one. I do not even want this Whirlpool appliance in my house when I can get a washer for cheaper than the cost to repair it.

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

The American Standard 95% 2 stage variable furnace is by far my favorite furnace to install. I know exactly what to expect from this furnace and I have had zero factory issues with this model. Outside of making a few sheet metal transitions this American Standard standard 95% furnace was very easy to install as well. And like the 2 stage variable … no factory issues.

The salesperson was great but we are not happy with our washer. We already had it swapped out once because of white spots showing up on our clothes. The only thing they could think of was that the bleach I used wasnt rinsing out completely so it showed up on our clothes. Recently, I washed a table runner by itself and it had some red in it. Now there are red spots on a couple of items that I washed after the runner. My husband just now asked why there were red spots on a shirt that he wears all the time. I explained. Also, we have had some white spots on clothes and I could scratch it out without leaving a permanent mark. Were no longer using bleach and we use only liquid detergent and all of it is HE. So I dont understand the machine. I hate it.

Whirlpool duet steam model: WFW9750WW00Serial: CSY3601165Please see attached the pictures of our washer that was purchased without a top counter balance from HH Gregg in May of 2010. We were told by the extended warranty technician when he came to diagnose the machine on 6/24/13 that the bearing and basket were bad. He ordered the parts and returned on 7/2 to repair the machine. Upon taking it apart, he discovered the top counter balance was missing and was the reason that the bearing and other parts had failed. I will include pictures of the plastic that the counter balance should have been attached to. You can see there are no screw holes or scuffs on the plastic. It was suggested by one of the customer service agents, Kitty in TN, that we remove the counter balance. Per Kitty, Because had it come from the factory like that, it would have walked all over the laundry room and not worked right since the first day. Honestly, we have scuffs all over our walls and my husband just thought the legs needed adjusted or it wasnt sitting properly on the pedestal. We have never owned a front load washer, so we didnt know what to expect. The washer sits in a very tight space under the cabinets, but will walk in the middle of the floor especially before we installed the pedestal.The top counter balance was ordered on 7/2 and we were told it would arrive and be installed today. The technician called me at 10:55AM today and stated the package had not arrived. We are asking Whirlpool for a replacement washer as the one we purchased brand new came from the factory defective. We have been told a solid NO. Upon further inspection of the machine while taking pictures, I noticed that the bottom counter balance is cracked clear through as well. Im attaching pictures of that. I did speak with Laticia in MI. She was VERY nice and more empathetic than the other 6 or so people we have spoken with at Whirlpool customer service. She was professional, helpful and I hope who Whirlpool would want representing their company and brand.We feel Whirlpool sold us a faulty machine and they should replace it. We have been told by them that they are sending the parts as a GOODWILL gesture, and will have the parts installed. Now after the whole inside of it is shot and possibly the motor and boards, thats awesome. We are now an LG/Samsung family. This was our 3rd and last set of appliances from Whirlpool. When the rest of these die, we will replace with another brand. How sad that what once was a great company, and I grew up with my mom and grandma thinking there was no other brand to use beside Whirlpool, now we are left washerless for 3 weeks. They refuse to stand behind a mistake that was made in the factory. Ive read these are made in Germany. Maybe Whirlpool needs to bring jobs back to the US and improve their quality control.

Whirlpool Cabrio Elite - I wanted this washer and dryer set to be the best one I ever owned. =( It’s the most I ever spent on a set. I am truly very disappointed. The washer, it is twisting the clothes and sheets so bad. My clothes are falling apart a little bit each time I wash them. I tried so hard to load the washer the way they asked never putting in a full load. The dryer leaves things still wet around the corners and edges. Because everything gets so twisted I had to buy a iron and ironing board just to get the wrinkled out. I hate to iron.

We thought we were going to love it. It has two bottom freezers so the capacity is fabulous, but the ice maker location subtracts shelf space. Love the French doors, but we can never find anything quickly. The biggest issue is the popping noises it makes that are sleep stealing in the night.

I have had my Whirlpool W10280546B HE washer for 1 1/2 years. For the last year, I have had constant problems with the washer leaving a large amount of residue (in spots) all over my laundry. I have always run my washer as instructed, and I only used HE detergent in the correct amount. This residue appears to be fine lint, but may be lint combined with detergent.I have used the washing machine cleaning tablets and powders, but this has not helped at all. No one seems to have ever heard of this problem. I have to clean off these spots which cover approximately 1/3 of each article with every washing. The dryer helps get some of it off, but not nearly all of it. Any suggestions besides buying another washer of another brand after only 1 1/2 years?!

Purchased at Lowes and within days of installation the water would heat up so hot that it would spit and spew out of kitchen sink (10 away) and be so hot you couldnt hold your hand under it. Returned to Lowes and they reluctantly replaced it. I should have bought a different brand but I felt confident that it was just a faulty thermostat. Second one did the same. Tested different settings and it seemed to work ok but a few days later it was scalding hot again. Tech support kept telling me that water heaters are intended to be used or they are like a kettle of water sitting on a flame. I told them they were crazy to think a small pilot light could heat 40 gallons to scalding temp.Guess what? I left the heater on the pilot setting and with 40 fresh cold gallons in it. I returned 24 hours later to find it scalding hot again. I got down and looked through the view window and I couldnt believe the size of the pilot light. It is the biggest pilot light I have ever seen. It blows like a mini blow torch! And there is no adjustment. This is a serious engineering flaw and extremely dangerous. This heater is at my father-in-laws house and he probably doesnt use 5 or 10 gallons a day but still, NO WATER HEATER SHOULD EVER HEAT WATER TO A SCALDING TEMPERATURE WITH ONLY A PILOT LIGHT!!!

I bought it on 11-24 13. I called Whirlpool on 1-29-13 and got no response. I called 3 or 4 times and still havent heard from them. Its now 4-1-13 and still nothing. I tried many times and got the runaround from them. They owe me money for repairs to the heater. I will not ever buy from them again. Just thought you all should know about this.

I have a one year old Whirlpool refrigerator which was fine for 6 months. Since then it has been a nightmare. If Lowe’s had not intervened on my behalf, I never would have gotten service. Have had at least 6 service calls, 2 new ice makers and various other parts. It should be bright yellow.

My new Washing machine was to be energy efficient. Yes, It uses less water to wash a load of clothes. Problem is, it takes twice as long to wash a load of clothes as older models. If it uses twice as much electricity, In what universe can this be considered energy efficient?

Purchased a new Twin Thin washer & dryer combo when I first moved into my new apartment two-years ago since it was a good fit for the space that lies inside my patio. Nothing BUT problems from day one since it DESTROYS/EATS your delicate clothing. Repairmen in and out could find nothing wrong with it. The problem lies in the fact that the so-called gentle cycle agitates at the same rate as the other cycles, but stops so that the agitation time is shorter, but at the same time the agitation no matter if its shorter is still too vigorous for delicates. Under contract, so keep having repairmen come at no cost to me other than a complete waste of money purchase inclusive of unwearable brand new RUINED clothing.Called the company the other day & was told they could SELL me a different one, but they would probably not pay to have the LEMON removed. Also, suggested I wash my delicates in a mesh bag which is impossible to do when one has maxi dresses that tell you to wash on the delicate cycle. Mesh bags are made for small items - DUH!Repairman came again today, and was kind enough to make call to them. Later found that their response to him was that I was putting too much into the washer. Like no way, Jose! Asked tech to forward e-mail to them advising that they were more than welcome to come film me when I wash because that was NOT the problem with it. Already knew Whirlpool had discontinued this washer/dryer combo, but THAT fact was never mentioned. A lot of sites online no longer even carry the parts for it. Found others with the same issues on various sites relating to this now discontinued model which is akin to a Purana fish with shark fins. E-mail sent to tech that was here today asking him to forward my e-mail to whomever he made contact with today via phone that unless the situation is remedied that I would have to take further action. Now awaiting response from the main man tech or whatever his position is at Whirlpool.Bottom line is that it is a LEMON that has not only cost me money, but excessive amount of time to resolve this issue not to mention time spent online researching this, that and the other concerning this discontinued appliance. Warning to all out there - DO NOT BUY WHIRLPOOL - UNLESS YOU WANT A HASSLE and a lot of BS. Found they already have an extreme number of lawsuits against them during my online searches. So, ball is in their court at the present time. Will be calling them the end of the week once again in order to get this problem resolved unless I hear from them via e-mail.Totally exhausted from it all. Word to the wise: DO NOT waste your money on Whirlpool appliances unless you want more problems than you already have. I have health problems which are exacerbated by stress, and believe me this has been one of the most stressful and one of the longest things to resolve (two years) brought on by their lack of admittance that this DISCONTINUED product is a real LEMON. BUYER BEWARE OF WHIRLPOOL - I rest my case.Updated on 07/12/2018: Cant seem to find this model anywhere now. Not to mention the fact that I found it not only eats my delicate clothing, but is also ruining my towels, etc. and I use the regular wash cycle for these items. You cant find my model #WET4024EWO anywhere; looked like they put a similar one out with a slightly different model # in which the drum/agitator differs from mine. Now find Im having difficulty finding that NEW stackable model on the WEB. Leaves me wondering if that one has also now been discontinued???They have given me no resolution to my problem as of yet, and Im totally EXHAUSTED from it all. Have high blood pressure, a heart condition, and cant even sleep right anymore due to their lack of cooperation to solve this on-going problem which is certainly not helping any of my medical conditions either. Its causing nothing but STRESS, STRESS, STRESS and more STRESS! Will be filing a complaint with The Better Business Bureau by next week if not resolved by this weekend (if I live that long).Updated on 07/17/2018: In looking at this Washer/Dryer Combo Model # WET4024EW aka LEMON again today after noticing more clothes which now have holes in them after being washed on the gentle cycle with the highest water level possible, I noted the size of the agitator. Bottom line on this is that the agitator also appears TOO LARGE for the machine which also could also be another contributory factor to the destruction capabilities of this now discontinued model. Also, inspected towels today and found torn stitching & thread tearing in those also; appears EVERYTHING you wash in this machine gets destroyed. In researching further on their newer makes noticed that the agitator appears either much smaller or has been removed altogether. Hopefully this will serve to aid anyone out there who is thinking of buying this machine second hand from anyone out there that is attempting to sell it vs obtaining restitution from Whirlpool.

The machine meets our needs and just the right capacity. It has just the right number of selection for proper washing. Very easy to load clothes and remove from the washer. There were a number of colors to select.

I originally brought this to the attention of Whirlpool on February 27, 2014, and they chose to ignore the matter I raised. I am appalled at their customer service, but then again, customer service has been dead in America for decades now. I purchased a KitchenaAid (Architect Series II, Model KERS807SSS02, Ser. XW4704146) oven in 2009, which included a 5-year extended warranty. The first time I had to use my extended warranty was the first time a pot overboiled and thus overflowed covering the top of my range. Since then, Ive had to have my oven serviced two other times, but resulting from a pot which overflowed on the range.The controls are located in the front, directly below the stove top. There is most definitively a flaw in the design of the model I purchased. It seems quite obvious to me that the design should have included protection from moisture reaching the controls. It is very common for pots to overboil, from time to time, and thus overflow, but this should not cause the controls to malfunction due to seepage. Had I purchased the model that had controls behind the range and controls above the cooking surface, moisture would never reach the controls when a pot overflows. It should not cost hundreds of dollars each time a pot overflows on a range. Had I known that the oven model I purchased had a design flaw that allows moisture to reach the computer controls of the oven, I would have purchased the oven with the controls above the cooking surface.I invested over $2K on this oven because having owned KitchenAid appliances in the past, the KitchenAid brand had historically proven reliable. KitchenAid (or now Whirlpool) can no longer take pride in the quality of their products, most likely relative to the loss of manufacturing jobs in the U.S. Whirlpool ignored me the first time I contacted them on this matter and most recently today when I was told that it was a use matter. Apparently they believe that an overflowed pot is not a common occurrence on a range. I wrote directly to Jeff Fettig, CEO of Whirlpool and he has chosen to ignore me.

We purchased a Whirlpool Range from Brands Mart USA and did not try to use it for quite some time because our house was not ready to move in. When we tried to turn on the oven it would not come on. We called a repair service and was told the Motherboard was not working. We realize the warranty was out on the stove but it never worked and the stove is Brand New. We called Whirlpool and they was going to repair and changed their mind on December 18, 2014 at 8:54 am. Before that call we had spent quite a lot of hours on the phone with Whirlpool and Brands Mart USA.. We purchased three appliances from Brands Mart USA Range, Dishwasher and Microwave at the same time they were all Whirlpool products. What happened to Good Customer Service and Return Customers for Job Security? Well neither Company care for their customers. We did not break a motherboard for a stove oven because the range was never turned on because it was broken when purchased.. We are unable to get any help from either company. I talked today to ** & Supervisor ** from-Whirlpool and ** - Brands Mart USA, again no help. Why transfer you from one company to another for 1 hour and 45 minutes? WISH I COULD GET SOME HELP. And we wonder why companies go out of business - word of mouth complaints and especially with Senior Citizens like us.

We bought all Whirlpool Gold Appliances when we re-did our kitchen 5 years ago -- fridge, d. washer, oven, glass top stove, and microwave. Recently I noticed a pool of water in front of the fridge. Turns out there is a sticky grommet problem that prevents moisture from draining into a pan on the inside back bottom of the fridge. Whirlpool will send you a replacement part that is totally different than the original poor design (a long hose affair) BUT wont pay for the labor to put it in unless the unit is less than 2 years old.I watched a video showing how to do it, but it looks pretty tricky and involved plus risky because you can break the drain pan in the process. Spoke with a Whirlpool rep and a supervisor -- both admitted to a quality problem but got nowhere on the labor. Theyre sending the part, and the supervisors supervisor is supposed to give me a call, so well see if they eventually do the right thing and cover the labor. I mean cmon... the parts obvious a bad design, or they wouldnt be sending a totally redesigned part! Covering the labor only if its two years old or less? Even the Whirlpool techs online are saying the problem happens after about 4 years! The grommet gets sticky and wont drain due to heat from the compressor, and that takes time to happen. Ill update this when I hear back from Whirlpool.