After 1 1/2 years, My new Cabrio washer lid hinge started to come apart and wont latch, so machine wont run. After a day or so it completely popped up and out of align. The lid has PLASTIC hinge. This is obviously a problem. We have been in touch with Whirlpool, but they say they cant help?? This should be a recall. We have been waiting on back order for a replacement Lid at OUR OWN EXPENSE since Sept. 20, 2015. I want to get this fixed and use my Machine again. We are Senior Citizens and this machine is used 3-4 times a week. Not abused.

I knew I couldnt be the only one with these problems. The reviews confirmed it. I bought my Cabrio washer in 2012. Energy efficient, no agitator to catch on clothes, Great. It took me a while to figure out that the machine was eating my clothes and not cleaning them at all. Oh, they smelled fresh. That HE detergent smells nasty. The machine ate the edges off my good towels, T-shirts, jeans. Brand new underwear (thick elastic) was stretched all the way out and pulled. Normal stains and dirt do not come out even with pretreating. I started running my clothes on the delicate cycle, prewashing stains in a bucket by hand and then putting clothes in mesh bag before running the load. They still came out dirty and ruined. When I run the loads, it still registers as not being that energy efficient on the controls. Id gladly trade it back for my old washer. I feel like I have stepped back in time to a time where you washed everything in a tub or bucket. What a waste of time.

Bought a Whirlpool French Door, Bottom freezer mount appliance from Lowes in Jan 2014. Model WRF990SLAM00. Jan 2015 the freezer part stopped working. Whirlpool approved repairman came and knew exactly the problem because he was aware of this being a consistent issue with Whirlpools. He contacted Whirlpool and they quickly agreed to send repair kit for FREE. Took 2 wks for parts to arrive, and neglected to send along required tool/gauges for repair to occur. I called Whirlpool C.S. and they claimed they knew nothing and said our fridge was on no problem list. I had repairman call Whirlpool and they claimed appropriate tool/gauges are no longer available! This fridge is only 1 year old!!! Now we are completely ignored. Whirlpool will not even talk to us about help of any kind. HORRIBLE customer service!!! Crappy appliance! After thinking our Whirlpool appliances were a good investment, I will NEVER EVER BUY WHIRLPOOL AGAIN!!!

First one had major problems. The bladder they call it. They took out the whole system out, replaced the tube that goes to the top of the refrigerator which is where it always starts leaking so they worked on it three times, junked it, gave me a new one and here I am again same thing. Ruined my hardwood floor and Im stuck with it. Never again will I buy WHIRLPOOL.

This has been our second Whirlpool Hot Water Tank in our home in the past 14 years. The first was installed by the builder, when it went out we purchased a larger capacity one from Lowes. It was professionally installed and now, after the extended warranty coverage period is expired, its expired as well. I would think you should be able to get more than 7 years out of not one, but two Whirlpool hot water tanks. No wonder they are no longer manufacturing hot water tanks - they sucked at it. Also, if you do have one, you have to get parts from Whirlpool and pay $30 shipping. No thanks, for the cost of parts to replace everything youre better off getting a whole new unit.

My washer and dryer have been a great experience. Doing laundry has never been my favorite chore but these energy efficient and state of the art machines live up to their advertising. One of the best things I like about the washer is the ability to set the run time for a future time. I do wish the dryer had something similar.

We bought a Whirlpool front door open washer machine from Best Buy on Oct. 2, 2011. We didnt start to use until our basement got finished. In November when the basement was ready, we found out that the machine didnt work at all. We called A&E factory service as suggested by Best Buy. They sent technicians 3 times in 2 months to check the machine. Now, it is 3 months later since we purchased the machine, the machine is still not working. We contacted Whirlpool, and they would not exchange to another machine, instead, they told us they will send another technician to check it once again. This machine costs us $800 before tax, but until now, it is still not working. Can you tell us what to do? We called Best Buy and they said this machine is under factorys warranty. So we called A& E service, who said that if Whirlpool called them, they will tell them it cannot be fixed. However, they need Whirlpool to call them because they work for Whirlpool. Is 3 month waiting not enough for a brand new machine to get fixed? And the worst thing is we still owe money to Best Buy creditor. Please help us to get rid of this! Thanks!

I am on my 3rd refrigerator from Whirlpool. The first one lasted 8 years, the second one lasted 6 years, and now the 3rd one has only lasted 4 years. This is just too much money to pay for a supposedly nice quality product and it go out as the warranty goes out. The second we had to replace the icemaker 3 times and a compressor. Now the 3rd is not cooling.

Dishwasher leaking thru the diverter motor; apparently the gramet # WPW10195677 gets worn out and starts leaking. They have discontinued the part and can no longer be found. I call Whirlpool and all Parts supplier in my city. Obviously this is something that happens with time (5 yr old dishwasher) and is something very simple to change. But if we cant find the part....what are we supposed to do. Also my dishwasher rack has broken 2 years ago and is holding with zip straps! Horrible product!

I purchased a GW399LXUS Whirlpool Gas Range. This is the slide in kind. I paid 1658.00 dollars for this stove, because it was a gas convection oven. We purchased it on 7/21/09. Just yesterday, the keypad numbers stopped working. I cannot even set a temperature for the oven. So now, I can only use the burners. I called Whirlpool today. They told me that my stove does not have any recalls so there is nothing they can do about it. I spoke with Jessica in Michigan. I told her how dissatisfied I was that the stove is only 2 years old and the most important part (the buttons) stopped working and they only cover this for one year. She told me that I have to remember that man made things are made to stop working at some time. I told her they should work for longer than 2 years. I remember way back when my parents bought a stove or fridge and they lasted for 15 to 20 years before breaking or stopping to work.I am a long time Whirlpool customer and always had good luck with their products. But I really feel that they should fix this problem. I could understand if the stove was 8 or 10 years old and something broke after using it, but not after 2 years. I will definitely tell everyone I know to not buy Whirlpool or Maytag since they are one in the same. I probably will not buy Whirlpool again and will have to buy something from Japan since it will last longer. So much for buying American made junk!

I have had my Whirlpool side by side for over 12 years. The 2 minor problems it has had, the repairman replaced the parts and she’s working great. Hope I’m not cursing it. Whirlpool 19.8 cu ft. Model EDOGTK.

Sounds crazy, but the outside of my stainless steel door is all dented. I live alone and one day noticed that it looks like someone body slammed my fridge. Is there air in the door panels that could be escaping or something like that? Anyone hear of this?

I like the washer for the most part. The thing I dont like is that even though I always keep the door open after doing a load of wash, the gasket continues to grow mold requiring me to do a monthly bleach/sanitizing process which is different than doing a bleach load of wash. The gasket also needs to be cleaned frequently. This is in a front loader.

Whirlpool Cabrio Model WTW6500 - I ask all of you to stay away from the Whirlpool Cabrio sets. I have spent hundreds of dollars trying to fix my washer. I just spent $260 for a computer board. Now it stays on rinse cycle. So now I need the motor sensor harness which is another $90. Service call $80 x 2. So, now I am going to take the computer board back and get my 260 dollars back. For the cost of $400 to fix this washer. You can go and buy a new one for around $400. Then, Im going to the lawyers to file a class action suit against Whirlpool. So, owners; be looking in your mailboxes for a class action suit against Whirlpool for those who own the cabrio set. Im tired of having to deal with whirlpool customer service. Maybe, whirlpool should think of having their laundry made back in America.

We purchased a dishwasher for $650 and within a very short period of time, the upper rack was so squeaky that it was intolerable. Service guys came and replaced the rack and wheels and all was well until a few months passed and it happened again. At that point, it was outside of the warranty, so we called upon our extended warranty we bought through Whirlpool. Guess what? That warranty doesnt cover the racks. So they referred us back to Whirlpool. They told us we had to pay for it ourselves. After being treated like a ping pong ball several times, we ended up paying about $150 for labor for another guy to come out and replace the racks again. Whirlpool agreed to pay for the parts. A few months later, we again have a squeaky upper rack that is so loud it wakes people up in our house and its less than two years old at this point. Weve been sold a LEMON!! Just got off the phone with a supervisor at Whirlpool who said they cant do anything about it and wont acknowledge we have a lemon. When I told her I was going to take this as far as I need to to resolve it, even if we have to go to court, she laughed out loud at me. We will never again buy a Whirlpool product. Our LG appliances have been great however.

Four years ago, I purchased a Whirlpool refrigerator - French doors (ice and water in the door) and freezer bottom drawer. Against everyone but the HH Greggs salesmans advice, I purchased the extended warranty as I had paid a large sum of money for the refrigerator. Within a year, I began experiencing problems with the ice maker. Over the next few years, I had to have it repaired/replaced an additional three times. Add to the whole mess the incompetency of the A & E Repairmen that required at least two visits each time to complete a repair and their inability to arrive during a 9 hour window, I stayed livid about my refrigerator for three long years. Finally, I demanded a replacement refrigerator under the lemon portion of my warranty. After numerous arguments, the warranty company offered me several different makes and models to pick to replace my hunk of junk. Stupidly thinking that my problems were related to one bad unit, I selected another Whirlpool only to have it completely crash a little over one year after acquiring it. I lost the food in it and am having to wait almost a month for the parts to arrive and the repairman to return. According to him, it will have to be completely rebuilt. I will never, never buy another Whirlpool!

My Whirlpool Microwave models WMH32519FS was installed in my new home by the KB Home builder Nov 2017 and went bad on Nov 23, 2018. As write this, my microwave is 1 year & 15 days old. Just out of warranty. The micro Keep show the same issue, open the door & closed the door. Still is not working, the microwave died On Black Friday 2018. RIP Whirlpool, I will never buy you.

I purchased the Cabrio washer and dryer 4 years ago and had no problems until recently. The motor and the harness broke and the cost to repair was almost as much as a new washer. The repairman told me that this is a common problem with all washers that Whirlpool makes as they have the same motor and harness. He gave me a list of all the brands that they make and suggested if I buy one to get an extended warranty. I would not recommend anyone buy an appliance from a company that continues to manufacture faulty products. I wonder if they own the extended warranty company?

19 gallon Electric Whirlpool water heater Model #e1f20us015v - Purchased this water heater from Lowes to provide hot water to small apartment with no kitchen for my son, built in my garage. Had unit professionally installed within 1 foot of bath to provide hot water for shower and sink in bath only. Hot water lasts only 5 to 6 minutes and takes approx. 2 hours to recover. My son cannot even take a normal shower! ntacted Lowes who was unable to help and told me to contact Whirlpool. Contacted Whirlpool after my model number would not even come up on their website. I asked tech what was the normal expected amount of time before hot water depleted. She did not know. I asked what was the normal recovery rate. She did not know. I asked for information on the energy rating. She said there was no information available. I asked how I could receive a refund. She said that they could only send a plumber to check unit and that nothing would be done if it was heating water. I asked to speak with a supervisor. She said none were available and said one would call me. I never received a return call. VERY DISSATISFIED with Whirlpool on this issue. It appears my only recourse is to purchase a new water heater and scrap the present one.

From the time I had the Cabrio top load washer, it has been repaired at least 8 times. I did get the extended 2-year warranty. I should have known that this machine was going to give me problems from the first service call. I have had to have the motor replaced 4 out of the 8 times the machine has been serviced due to coins getting into the motor. I have a problem with rust around the dispenser. I also feel that the clothes get very tangled when washing. The machine is just 5 years old. This time when I called for repair with A&E appliance repair, they told me that it was going to be $450.00 to repair. Now, I am not going to repair it, especially after having all the problems I have had with it. I will never purchase another Whirlpool product or any of their other products that they make. I did call Whirlpool just to let them know my problem and to let them know that there have been hundreds of complaints with the same washer that I have. It’s too bad that Whirlpool has no respect, passion or pride in what they make. I am going to purchase a new washer and it will not be anything related to Whirlpool.

I purchased model FG1F4040SEPV Whirlpool water heater from Lowes about 5 years ago and have had to literally replace the thermocouple each year. At least 3 of these years we have had to pay someone to fix this for us until we learned to do it on our own. Im very surprised Whirlpool didnt recall these water heaters and make it right for their consumers. What this did for us was confirm that we will never purchase another Whirlpool item ever again. We are switching over to Kenmore!

I bought this stove 4 years ago from Lowes. I have had nothing but problems ever since. My family is now afraid to use the stove and Whirlpool refuses to stand behind their product. The last straw was a bill for a service call that took 6 months to complete without correcting the problem. Whirlpool sent me a bill for $100 to pay for the privileged. When I complained, WP said if I paid the invoice, they would give me a deal towards a new stove. Meanwhile, the old stove does not work and we are afraid to use it, given our experience with its reliability and safety. I plan to return it to Lowes and buy anything but a Whirlpool product. Beware of Whirlpool Maytag anything!! The customer service is shameful!!

Whirlpool Refrigerator Freezer WRF560SEYB01. Purchased the Whirlpool Refrigerator Freezer in 2012 at Sears. Ran okay for 2 years. Bottom freezer door came off the track. Called Sears. Sent out repairman for $200 to replace the door. He did not check the ice buildup on back of freezer. Next problem, severe ice buildup, loud noise. Used hair dryer to melt ice and took the blower fan out of freezer. Solid ice on all the blowing fans and found a chunk of solid ice. Freezer no longer made the noise until the ice built up again. Now, it continues to build up and we have to use the hair dryer every two weeks. A refrigerator should last at least 10 years. This model doesnt even warrant a rating of any kind.

Worst company for home appliance... I got my fridge repaired from an authorized service person and next day it again stopped functioning. Upon calling the service center again, they said that few more things needs to be repaired once again and for that fridge needs to be moved to their workshop and for that they will be charging 1600 Rs again. Upon asking for the refund for the useless spare part, the rude service person said ek din k liye to chale tha na fridge, fir kis baat ka refund... Such a ** company is Whirlpool that they are not entertaining any complaint on their all India customer care number...

My washing machine quit working with one month left on the warranty. In trying to schedule repair I was never able to talk to a live person. Via chat and online scheduling they could not or would not come out for 10 days. Also they would not approve use of a local repairman who was willing to work on it in 2 days. Waiting 10 days for service on a washing machine is crazy.

I am thoroughly disgusted with Whirlpool. How dare they sell the garbage that they put out? I didnt buy the extended warranty when I bought my Whirlpool washer and dryer. Why should I when I put out all the money that I did? I havent had the product three years and had to have a repairman out to fix. And then the parts are so expensive, and they are cheap Chinese junk. I dont understand how something with a name like Whirlpool can put out such a disappointing product. Never again will I purchase your product. And I certainly will spread the word. Greed comes to mind for me. I see you have contributed much money to campaign (Republican). Have you ever thought about what you do to yourself? How absolutely disgusting you are.

Whirlpool Dryer Model WED4815EWO and Whirlpool Washer W10682799 - I have always had great results with Whirlpool products. Both are energy efficient and save on operating costs. I purchased them three (3) months ago. The washer locks during the wash cycle. That took a little getting used to. I have always been able to rely on Whirlpool products. The top loading washer (W10682799) is energy efficient and high capacity. It regulates the water level so you dont have to worry about wasting water. The matching Dryer (WED4815EWO) has a sensor to regulate your drying time or it can be manually set. I appreciate the worry free, self-regulating functions on both the washer and the dryer.

I purchased a Whirlpool front loading washer from PC Richards in January of 2010. The warranty was only for one year (the washer was new, not used). The model # is WFW9050XW. Anyway, the washer had to be repaired by PC Richards twice in the first year I had it. Once because the belt that makes the washer spin broke, then because the pump got clogged. Unfortunately, when you wash your clothes, your socks and underwear can get sucked into the pump. After that warranty expired, I purchased a warranty from my utilities company (PSE&G). I have had to contact them four times for repairs to this machine. The most recent problem is my clothes are still wet after the washer stops. I actually have to wring them out by hand to get the excess water out. When I contacted my utilities company about servicing the washer, I was informed that if the repair is more than the washer is worth they dont have to fix it. I canceled the repair and now got to the laundrymat. I figured if I wait until the end of the year, maybe the repairs wont seem excessive. I contacted Whirlpool about the problems and was informed that I should have been using a garment bag to wash my socks and underwear in. More or less the person I spoke with made it seem as though it was my fault the machine sucked up my underwear and socks. I, on the other hand, disagreed with her. I told her the washer should have been build so that it would not suck up these items. I was so totally pissed off I ended the conversation. I also informed her that I would not be purchasing any other appliances manufactured by Whirlpool or Maytag as they are affiliated. They obviously have no integrity when it comes to their product. However, I am totally baffled. Why do the Maytag machines work better and last longer than the Whirlpool machines? The washer I replaced was a Maytag. I had that machine for 17 years!!!!

The first washing machine I bought was a Cabrio. Started having problems right off. After the repair people had been there several times we finally got Whirlpool to replace the machine. We got another washing machine. We bought two warranties because it kept tearing up. Repair people said this time it would take $1500 to fix it so of course AIG said, We will not pay this much. So I have a washing machine I have spent $1600 on and it leaves, greasy spots all over my clothes. So fed up with Whirlpools trash!!

I purchased a Whirlpool Microwave GMH6185XVQ1 on 7/2010 for kitchen remodel. It needed a magnetron repair just after one year warranty ran out. I called Whirlpool and they agreed to repair. Whirlpool sent me an offer for an extended contract. I purchased it. Since microwave was out of warranty at time of contract purchase, I was told there would be a 60-day waiting period. Microwave broke again on 3/2012. I waited until extended contract was in effect. I was told since microwave broke before contract was valid, I would have to pay out of pocket to repair, then contract would be valid after that. It appears (per internet research) these microwaves have bad magnetrons that need frequent repair. I wrote to BBB to complain.

I owned the Whirlpool washer for 13 months until it quit. Menards was no help with anything. I am going tomorrow to get to try my luck with Samsung.

To be fair to Whirlpool, I have contacted them but have not given them time to respond. I feel so strongly about this issue that I want to get the message about this company product out. About 2 years ago, we purchased a Whirlpool fridge, stove, and dishwasher. I have had so many problems with the stove (WFG540H0AS0) that it has pissed me off, actually. First, the knobs that control the stove top melted. MELTED! We had to replace them to the tune of $30.00 each and there are 5. Why would anyone use knobs that cannot withstand heat on a stove?! News flash, I cook on my stove. Therefore, there will be heat used. Second, the oven keeps shutting off in the middle of cooking my holiday meal. Of course, this made my turkey take much longer than usual. Today, it shut off in the middle of cupcakes. Third, the oven does ignite without turning it on and off multiple times. So we called the repair person who told us to replace the ignition switch for it. This helped for about one month. Then the problem started again. I just emailed Whirlpool and I will call them next business day. I am so disappointed with Whirlpool. I thought they had a good reputation for quality products.

Dishwasher has had multiple issues in the 4 years of use. - Incomplete cycles - need to call repairman to figure out why the dishwasher does not complete cycles, fills with water but doesnt go into clean cycle - In 2 years had to replace grommet due to leaking water. - Top rack slide rail plastic ends broke needing to purchase both new ones. - Detergent door quit opening - door does not open during entire cleaning cycle.- Design flaw with silverware rack on the door, be careful not to block or silverware will not get cleaned.

Bought a Whirlpool refrigerator from Best Buy a yr 1/2 ago. Went wrong from delivery and never stopped! There isnt enough room here to specify so Ill try to synopsis this. They screwed up delivery date and then time. Fridge was unbalanced, doors wouldnt close delivery guys didnt know what to do. Tried to fix it and then call their office and were put on hold for over 30 mins. And the Rep was unhelpful and rude to me and then the delivery guys finally got door shut on freezer but Ice maker wouldnt work so they said they would have to have someone Whirlpool to fix it after them talking and being on hold again with their Rep. They were upset and late and felt sorry for me and told me Confidentially That this was not uncommon and they would do what they could to help me.It took many calls, people and conversations (subsequently I found dents, drawers cracked, cracks in back wall) for them to get someone here. When they did the guy was rude and acted like a pre-programmed robot. He said, Show me whats wrong and I did. He stood there and just stared at me and said, I dont see anything wrong. I was shocked! I said, You mean thats supposed to shower the kitchen with crushed ice, etc? He said YES! I said, Ok, please leave my home. I will contact Whirlpool and Best Buy Again. I did and it went on and on and on and to this day theyve done nothing. I have copious notes, dates, names etc. I have also heard many other complaints about both companies and will never do business with either again and will tell anyone and everyone I meet.

We purchased a Whirlpool dishwasher in August of 2014 (Model #WDT710PAYM6) and it broke for the first time in the summertime of 2015, so it was still under warranty. The manufacturer set us up with a local company to fix it. First of all, the guy comes out to look at it and has no parts with him whatsoever to fix it once he figures out the problem. So we ended up waiting for over a month before our dishwasher was fixed. That is a long time to have to hand wash dishes, especially with the amount that we go through each day. I know that ranting about having to hand wash dishes is such a first world problem thing to complain about, but my gosh...if I buy a brand new dishwasher for a good amount of money, I shouldnt have to hand wash my stupid dishes!!It has now broken AGAIN and it is no longer under warranty. We called Whirlpool to see what they could do because it should not be breaking this often. They told us we could either spend $250 for a years worth of maintenance on it, or just pay out of pocket. So you want me to pay $250 or more to fix a dishwasher that we spent over $400 on that has broken twice in a year??? Ive been looking on their website for this model to leave a review and cannot find it, so that leads me to believe that it is discontinued. So thank you, Whirlpool for the piece-of-crap dishwasher. I can see you really take care of your customers when they call about their concerns too. I will NEVER buy any Whirlpool appliance again, and I will be sure to let all of my friends know they shouldnt either. If I could rate this with negative stars I would. So now we have to go out and purchase another dishwasher. Thank God Cyber Monday is here. So I cannot say it enough, do not, do not, do not buy a Whirlpool. If you do, youll find its actually a Whirl-poo, because its a POS.

I had a kitchen fire in 1999. All appliances were replaced with Stainless Steel Whirlpool. My old fridge was an 18 y.o. Whirlpool and still works fine in the garage. My old above range microwave was 12 y.o. and worked fine, I should have kept it. I had to replace my new Whirlpool Microwave after 4 years and 4 repairs. (Main Power Diode kept failing). Now my Whirlpool Gold fridge is not defrosting, even the freezer light switch is frozen. This French door freezer also seems to have less capacity than my old upright freezer. The retailer seemed sympathetic and pathetic. They would not budge on repairs. I told the contractor that did the rehab on my house what happened, he said he would stay away from Whirlpool and that retailer.

This is our 2nd circuit board failure in the 4-5 yrs, since we purchased this very expensive range/oven. The first time was shortly after the warranty ran out and Whirlpool would not even send us the part for free. They said there was nothing they could do. So this time we are not even contacting them and are just having our repairman order another new one. For a $1600 range to have to put more than $400 back in so far, I would never buy a Whirlpool again. I have been very careful not to use any cleaners on the circuit board as I was told by our repairman that that shorts them out. First the convect bake button wouldnt work, nor the convect roast, now the bake button, so the only buttons that work are broil and warm. Even the timer is shot. What a piece of junk (electronically). Beware buyers!

Brand new dishwasher and first time I started it I noticed the timer showed the cycle taking over 3 hours. When done I opened the door and there was some water in the bottom and the door was very wet. Dishes had not been washed. A glass that had turned upright had no water in it. The soap pod was still intact. I started over again and the same thing happened - two more times. The silverware is not clean either. Its going back!!! Im sure there will be resistance but we will deal with it.

From day one I was not happy with the new auto fill washer, I was told I just needed to get used to it! Well I have tried every cycle available and no matter what I try cloths don’t come out clean, using the deepwash cycle Sheets on top were still dry once cycle was completed!! Give me back my old washer! Washed much much better.

My company purchased a lot of products in Whirlpool company. We thought the product is good, until the dryer machine didnt work all of a sudden. We call a customer service. After a week the maintenance came in our unit to check the dryer but he said that they need to purchase the other part of the dryer. That was happened last july. Were keep calling the customer service. We cant even count how many times we call them. But unfortunately even them they cant give us an exact date when they can fix the dryer machine. SLOW RESPONSE FROM WHIRLPOOL COMPANY!!! Shame on you guys.

We bought a Gold Series dishwasher on 2/12/2013. It stopped working properly and we had a service call on August 6, 2013. Since then, we have had 3 companies come out 5 different times to try to fix the machine. Nothing on the top rack gets clean. In fact ,they come out dirtier than when they go in. The last service call was on October 7, 2013. I was told by a Whirlpool representative that the repairman would call technical services and that if the problem was not solved, that the machine would be deemed unrepairable and that Whirlpool would replace the machine since it was within the warranty. I was also told that their standard is that if a machine has to have 3 service repairs to be deemed unrepairable. So 7 days after the last repair, the machine was still not washing correctly. Once again everything on the top rack was dirty. The machine has had the motor, the pump, and the hoses replaced. Still doesnt work. So I called again to get the ball rolling on replacing the machine and was told that they would not replace the machine and that I needed to have another repairman come out and sit in front of the machine and call technical service. Apparently, the previous repairman didnt follow their instructions. I called and complained twice, I guess Whirlpool thinks that as consumers we have the ability to change work schedules, school schedules, take vacation time, etc. to wait around for the 6th service call, and wait through the 5-hour window that we are given for the repairman to get there. Well we dont. Obviously I have given Whirlpool plenty of opportunities to fix this problem. They havent been able to do so with 3 different companies. There comes a time when you just stop kicking the dead horse. Now is that time. If they cant figure out whats wrong the first time, and not the second time, and not the third time, why do they think the 6th time is the charm? Because I got so upset with them, they referred me to a customer care manager. She called and left me a message, and I have been calling her now for 2 days with no success on her DIRECT line nonetheless. My phone calls are not returned. I wont even go into how many customer service reps told me a different story every time I called. Whirlpools customer service doesnt care about their consumers. They dont care about our complaints. Now I have a $600 piece of junk. I will never buy another Whirlpool product. I will make sure that every person I know that is looking at appliances knows about what a horrible company Whirlpool is. They just put crap in a shiny package!

After reading many of the 1,500 +/- complaints about this inferior product, I guess I should consider myself lucky. Ours didnt fail until this past Saturday, March 22, 2014. We purchased this Whirlpool (American Water Heater Company) water heater FG1H4040T3NOV at Lowes, and had it professionally installed, in October 2004, and we have had no issues until this past Saturday when we woke up to no hot water. After checking for the obvious, and finding no apparent cause for the failure, I considered it a fluke and relighted the pilot. The pilot took a few attempts to light, but it lit, and the burners came on.Three days later, we woke to no hot water again. This time, we placed a service call to the company that did the initial install. The technician came out, and after his inspection he informed me that the thermocouple/burner assembly needed to be replaced. He also informed me that this is a well-known issue, and Whirlpool has been sending out free updated replacement parts. He called Whirlpool, only to be told that they are no longer offering free, updated parts. Whirlpool also cited that the water heater was out of warranty (by less than 5 months). He gave me Whirlpools number, so I could contact them myself.As I smelled a rat, I began to do some online research about this issue, and, to my chagrin, I found out that I was far from alone with this issue. As of this writing, 1,500+ consumer and professional complaints, a settled class-action lawsuit, etc., etc. I contacted Whirlpool, explained my situation to the support rep, and, he proceeded to tell me that he couldnt help me with free replacement parts, due to the warranty being expired (less than 5 months). I argued with him, stating that this is not a warranty issue, but is in-fact a design/manufacturing defect issue, that has resulted in a redesign/re-manufacture. I cited the myriad of online data and negative testimonials, and I reminded him about the settled class-action lawsuit on this very topic. He acknowledged all of the above, was unimpressed, and offered to sell me the parts.After 15 minutes of back and forth, I asked to be escalated to the next level. But, of course the supervisor was unavailable, and If Id care to leave my name and number... yeah, right. Bottom line, Im very angry! I paid good money to Lowes for Whirlpools product, with a nine-year warranty. I had it professionally installed, and we have no hot water due to poorly designed parts. And... I am being forced to purchase the redesigned parts. Its truly unsatisfying to be an American consumer these days!

I purchased all new Whirlpool appliances for my kitchen from Lowes about 5 years ago. The dishwasher was leaking water onto my hardwood floors after about a year. I figured out that the seal was pulling away on the lower left corner. I fixed that myself. It cleaned pretty well for about 3 years. Now its not cleaning at all. I took the lower spray arm off to try to clean it. Almost all of the holes are clogged with debris. (I clean the filter at least once a week.) I went ahead and ordered a new sprayer arm, maybe that will help.As for the rest of the appliances... After about 6 months, the freezer started filling up with water that then froze on the bottom and allowed water to pour onto the floor. The microwave handled broke after about a month. (They did send me a replacement handle.) The knobs on the stove are starting to peel. One of the knobs wont stay on, so I keep it in the drawer next to the stove. Overall, I am very disappointed in all of the appliances. This will be the last time I buy Whirlpool.

Bought wtw4800 washer brand new came with 1 yr. warranty. 19 months after buying plastic bearings went. 2 different technicians told me could not be repaired, junk. Washing machine less than 2 years old and can’t be repaired. Called Whirlpool. Told me they could do nothing to help me.

Bought a French door whirlpool gold, wanted a good long lasting fridge. Bought in late 2011. After having it a couple of weeks we noticed the ice maker would take days to make ice. So we called to have it looked at. The repairman said if it is slow, switch it to fast ice. It made ice even slower, but the repair company said if it is making ice, and he comes out, we would be charged. So we lived with it. In 2014 it stopped making ice at all. We called they sent someone out and said it was a control board. They had to order it, and came back a week later to put it in. They left and said we would have ice soon. Never did!!!So we call again, they come out and said no power to ice maker. He called Whirlpool and they said wires in the freezer door were worn and broke. Well the door is non-serviceable and the cost of the door will exceed the price of the fridge! What kind of crap is that!! Long story short I will never buy another whirlpool again, and when I hear of someone buying new appliances I warn them to stay away from whirlpool!!! Run!!!

Handle needs smarter design. I purchased model #WRT311FZDM00 in November of 2015, didnt install in my new home till December. I am a single senior female, so there is little wear on the fridge, unlike a family of several people and with kids. The door handle actually broke just behind the screws that hold it in place, the plastic part of it broke into a couple of pieces. The cost to replace this handle is approximately $80, which is ridiculous in my opinion. Please start making things of quality materials instead of cheap plastic, especially at a stress point of a part. Even I know better than that. All 4 of my major kitchen appliances are Whirlpool, as well as my washer/dryer. I thought I was buying quality products. Hopefully things will hold up better with the other ones.

I had owned another Whirlpool Washer before, which died. I purchased this one. It was noisy and unreliable. Whereas the previous one lasted for 10 years, this one stopped working in less than 6. I went out and replaced it with a GE instead.

Good washing machine for 3 year. 4th year onwards your repair cost starts increasing. I purchased machine for 24 k. Now my repairs costs are 25 k. Each time the service guy comes puts me a bill of 7 k and above. The complaints to Mr ** goes to deaf years as he never picks the call. Their visit charges also are more and never give warranty above 30 days. How will you feel when you have paid more money on services ce than the product. I have supporting hills for all.

Very dependable. Like the steam clean function. Love that it is front loading. Like that the machine has windows. The functions for towels is a plus. Time remaining convenient. Machine is very good looking.. A big plus is the choices of many different functions, many that I have not yet used, but are available too.

Despite always using the designated (he) detergents and trying many different brands in appropriate amounts, this washer always leaves an ugly white residue on clothes. This happens all the time, requiring whole loads of clothes to be rewashed, sometimes more than once. This defeats the whole purpose of conserving water, which is reflected in our water bill. We also placed the laundry room on the second floor to make it easier for me with my disabilities. I am constantly having to climb the stairs when the machine gets unbalanced in addition to the extra loads from the residue. I was very excited to purchase this machine. Unfortunately, these feelings didnt last long.

I just bought a house that has one of these ranges, and it was getting the F2 message. I found the problem. There is NO ventilation behind the electronic control so when the oven heats up, the control board gets too hot and throws the F2 code. That would indicate a bad temp sensor or bad board, but really its the heat shield on the back. Ive removed the metal plate from behind the control panel and it works fine now. Im considering drilling some vent holes and adding some insulation behind the control.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

Whirlpool Model WDT920SADM0 Dishwasher. We built a new modular home so Abraham Builders ordered all my kitchen appliances in 2014. We did not move in and start using the appliances until June, 2016. Here is what happened during the first 6 months: 1) Would not dissolve dry soap or packets as there were still particles and plastic in the dispenser. 2) Dishes were not getting clean and were spotty. 3) Would not dry dishes, ever!!! 4) Parts would keep popping off as we would find them on the bottom or hanging down. 5) Final straw was this morning around 4 a.m. (12/4/16)... woke up to the smell of wire burning in the house and discovered it was coming from the dishwasher that we had put on delay wash that night and when we opened the door, smoke came out from inside!!Since it was past purchase warranty date, we had no warranty and the builder would not return any of my calls on any problems and the manufacturer of my house closed the factory. Needless to say, we now have to spend another $900+ for another dishwasher! Not happy at all about this Whirlpool model and would not recommend it.

I have a Whirlpool 33 inch wide Side by Side refrigerator. WRS311SDHM. This is the worst refrigerator I have ever had. Temperatures are inconsistent. It is less than a year old. Initially, I stored the big container of spring mix lettuce on the bottom shelf of the refrig as it wouldnt fit in the crisper draw. The temp setting in the refrigerator was set to ideal. Oddly though, in the freezer, ice cubes were melting and refreezing creating a massive frozen block. So, I raised the temperature in the refrigerator, but kept the freezer at coldest. However, I noticed that when I set the refrigerator to a warmer setting, ice cream became cold soup despite the coldest setting.I called Whirlpool and a service technician from Georges Appliance in New Providence, NJ came to my home (of course I had to take half a day off from work). He stuck a thermometer in the freezer and said, its working fine. While at my home he called Whirlpool who said that if lettuce isnt kept in the crisper drawer it will freeze (silly woman, dont you know that?) and ice cream will get soft in the freezer if the temp in the refridge is warmer than ideal. So, it seems I can have lettuce or ice cream, but not both. Okay, so I put the temp back to ideal, bought smaller packs of lettuce that would fit in the crisper draw and called it a day. Nope....lettuce and anything else in the crisper draw freezes too. Wilted, soggy lettuce is so nice in a salad and frozen baby carrots can break your teeth.I have been on the phone with Whirlpool executive dept several times. They offered to have another service company come out to look at the refrigerator. This repair company would not give me a 4 hr time frame until the day before the actual service call. This might be okay if you work from home or are retired, but this is not my case. I opted to not have them come. This is my last Whirlpool product. Since KitchenAid and Jenn Air are owned by Maytag/whirlpool, my other options are LG, Samsung, GE or Sub Zero.

I bought a Whirlpool Cabrio a few months ago. Every time we do a load of laundry, the clothes are not getting cleaned. Dark colored clothing, including grey clothing, comes out of the washer with white residue, streaked all over the clothes. We have to rub the residue into the clothes to make it go away. If we attempt to dry it and do not get the residue scrubbed off the fabric, when the clothes get dried, there are white streaks in the clothes. This is extremely frustrating. We spend a lot of time getting the residue rubbed into the fabric every time we do a load of laundry.The local appliance store has told us that perhaps we are using too much soap. We have used nothing but the high efficiency soap, as recommended by Whirlpool, and have reduced the amount of soap per their suggestion. It is now to the point where we are using hardly any soap at all, in the hopes that we would not have to spend 30 minutes working on the clothes after every load. That has not worked. The white residue is still all over the clothes, and since we are using less soap, I dont think our clothes are actually getting cleaned.When we wash a load of whites, they arent getting cleaned at all, even when we use bleach. In fact, when I compare brand new undergarments with recently bought undergarments that have been washed a few times, the ones that have been washed a few times are noticeably different in color, they are actually starting to turn grey in color.I have used Affresh in the washing machine, per the manufacturers suggestion, numerous times. We had thought maybe that was the problem. But even the load right after the Affresh treatment leaves the white residue or does not get the clothes cleaned.This washing machine was close to $700.00, and I feel that for that amount of money, I should be able to expect clean clothes. I have never had a problem with a Whirlpool product before, so I had no qualms about purchasing this washing machine. At first, I thought maybe it just needed to get broken in, that it would stop leaving the residue after it had been used a few times. However, that has not been the case. I have tried everything I can think of to improve the performance of this washing machine, but nothing helps.When I contacted the local appliance store to complain, they suggested I cut back on the soap. I told them that I had tried that and it didnt work. They told me to use Affresh, I told them I did that. I asked them if they would take the washing machine back; let me trade it in for something else. I would even be willing to get a cheaper washing machine, I just wanted something that worked. They told me they couldnt do that. Even though I was still under warranty, unless it was broke, they couldnt do anything, and even then, all they could do would be to try to fix it. They couldnt take it back and give me a different washing machine.The experience I have had with this washing machine is the worst experience I have ever had with an appliance. I had always thought of Whirlpool as a trusted brand for appliances, but if this washing machine is any indication of how they now makes appliances, I will never buy another one of their shoddy products again; and you can guarantee I will be telling my friends, family, and coworkers not to buy Whirlpool products either.

In July 2012 I purchased refrig, ed2khaxvb (model #). By Oct. 2014, after numerous service calls to unplug ice blocking chute, an ENTIRE door was factory ordered and DELIVERED. Feb 2015, A&E service installed new door. Later that day, I opened the freezer door which had insufficient suction and ice is again sliding down the chute to the floor. The stress this has caused me (87 yrs old). Case #, phone and ref..nos. could fill a book. PLEEEZE HELP. What can I do???? Ty.

I initially purchased all new Whirlpool products as part of my new home purchase in a Pulte subdivision, June, 2011. My WP microwave failed to heat in 2012 and the replacement of the Magnetron and Inverter and service was covered under warranty (would have cost me $493.51). Sadly, the microwave again failed to heat in 2014. I was so disgusted with this second failure, I decided to live without a MW until January, 2016 when I paid for my second service call and learned, once again, I needed a replacement Magnetron and Inverter, to the tune of $400. Both servicemen told me the 2011 magnetron/ inverter mechanisms were new technology and did not last long. Again, sadly, when I contacted Whirlpool, they would not admit to their defective product line and indicated they could do nothing since I am out of warranty. It is unconscionable that a corporation is not liable for their defective products.

About 29 Nov 2011, I bought a Whirlpool microwave, which model no. is magic cook 206 (mech). Sr No. CNF103400315, when we bought this item, we asked for the start up kit, but at that time they said that in grill microwave we dont provide start up kit but after a month when I again raise for start up kit, that time they give but in start up kit some item is missing and the sealed is open. So I kindly request you to take some action to the shop.

I bought a Whirlpool fridge in June of 2014 and the plastic part of the stainless steel handle that attaches it to the fridge broke about a month or so later. After replacing the fridge because the company said they no longer made the part they gave me a new fridge and with that one the door would not close without leaving a gap of about 1/3rd of an inch open at the hinge side. They took that fridge back and sent me a new fridge. A week later I got in the mail a handle for the first fridge which I no longer had. About a week after that I noticed that the latest and third fridges handle had a crack in the same place. Whirlpool sent me 5 replacement parts and they were all defective with the same crack visible in the replacements. Finally I got a replacement handle that looked good and it broke today, Feb 6th 2016, in the same place as the first one. I should mention that each time the company replaced the fridge it was with a different and better model and each with a slightly different handle. There are other design flaws with the fridge. The door is in a corner and there are cabinets on the wall so the door can only open slightly more than 90 degrees which makes it impossible to open the crisper drawer enough to get a cabbage in it and if I want to clean the crisper drawer I must move and turn the fridge in the kitchen. Also if the crisper drawer is not closed completely it causes the guard rail on the bottom door shelf to fly off sending everything on the bottom shelf to fall to the floor. Fun when some are made of glass and filled with liquid. You would think I would have learned my lesson about this company but no! I went to Lowes and bought a Whirlpool dishwasher and when I saw that the automatic door would not open enough to dispense the soap, powder or packet I called a certified Whirlpool repairman who told me after receiving a duplicate that of course would not work either, that there was no solution to the problem and I went back to Lowes and bought a Samsung and my problems were solved. I WILL NEVER BUY ANOTHER Whirlpool or as I now call it, Whirledpoo, product, EVER.

My 2-year-old Whirlpool Gold Series model replaces a 20-year-old Roper. So far it has exceeded expectations for low noise and useful features like validated Sani-Rinse. Has all the normal features plus Eco-Dry, Sani-Rinse, delayed start, five levels/cycles of cleaning, and hi-Temp wash. Fits where the old Roper used to be and handles a full load of dishes with room to spare except Thanksgiving, which takes two loads. Smooth black front with touch buttons and blue lights. Looks nice. Using Sani-Rinse seems to take a long time, generally around 3-hours for a full wash cycle. Besides being ultra-quiet, the unit is very energy efficient earning good Energy Efficiency and water efficiency ratings.

We purchased a Whirlpool Gas Water Heater (Model No. N40T61-343) from Lowes in the Summer of 2013. 2.5 years later, the water heater goes out as of 01/19/2016. Therefore, I contacted the telephone number on the side of the water heater in order to restart the water heater. We followed the instructions by pushing in the pilot button, as well the ignition button. To no avail, the water heater did not restart. I called customer service on Thursday (01/21/2016) to speak with a representative. She said that we needed another Thermopile and a Gas Valve replacement. So, who is going to put it on? It would cost as much as getting a whole new water heater. Therefore, we are going to Menards to purchase the Richmond Gas Water Heater. We had a Richmond once before; and it lasted from 1999 or 2000, until 2013.After reading all the reviews about this brand water heater (Whirlpool), no wonder people are complaining. Ladies and gentlemen, do yourselves a favor and not buy a Whirlpool Water Heater. The only thing that Whirlpool is good for is only their name. Their Water Heaters in particular are worthless pieces of junk. NEVER BUY A WHIRLPOOL GAS WATER HEATER AGAIN!!!

It has been a rude awakening, that Whirlpool is a substandard company. I have gone through 3 refrigerators under the label Kenmore, Whirlpool & 2 1/2 days ago Maytag. I purchased a Maytag 9 years ago and it is still working fine, and even cools a bit too much. Now mentioned labels are under Whirlpool; Since Whirlpool bought out Maytag in 2006, Whirlpool turned Maytag into a sub standard product company. They are spuming refrigerators with defective thermostats. Just think of it, I am one customer that have had the same issue with 3 REFRIGERATORS UNDER 3 LABELS MANUFACTURED THE WHIRLPOOL. I just called Maytag, and when I tried to make sense of the name of either Daren, Karen or Taren, ** hung up on me. I then called Home Depot online major appliances & ended transferring me to WHIRLPOOL!My Maytag refrigerator was delivered 07/25/17, after less than 24 hours, I had to move the settings to 4 from 3 for the refrigerator. She said that if the refrigerator cools enough at 4 then there is nothing wrong! Nothing wrong! To be substandard, in my book its plenty wrong. They have no business sense nor customer service sense. I will buy another refrigerator or appliance from any Whirlpool labels when hell freezes over! For them to accept substandard parts, probably foreign, it is not acceptable in CA nor the USA. Since; since this is a foreign owned company, I pray they will be a company not doing much business in the USA unless the measure up to our standards. Since; going forward we will make American and Buy American!

We moved into a new home (brand new construction) in Dec 2018. The ice maker/water dispenser has never worked. Weve had 2 different repair people come a total of 5 times to no avail. Now have to deal with Whirlpool directly to deal with Warranty. Will Whirlpool offer a new fridge? No, they will send a replacement door. 8 months later and we still have a fridge that does not work. Not impressed with Whirlpool and extremely unsatisfied with the produce. Do not buy this brand.

I had problems with the door closure on day 3 of my French Door Refrigerator Model # WRF560SEY. The flap on the left door that seals them fails to fold back if I open the right door first. Which didnt seem like a big deal until I tried to close them and have to remember to close the left door first or itll bang against the right door and Im afraid itll break that piece off then the refrigerator is worthless. The manufacturer drop shipped a new piece, after several attempts of adjusting the closure, and it still does not work. I have written Whirlpool and am told they have a new door on order but it will take 6-8 weeks, that was in March. Now when I contact Whirlpool no one ever returns my calls or emails. I have had the refrigerator only for 15 months and I have fought with either the store or Whirlpool since the third day of owning it. No one cares as long as the appliance is paid for. I will never buy another Whirlpool appliance.

I purchased a Whirlpool bottom freezer refrigerator for my wifes birthday because my old one was old, ugly, rusted and didnt match. Since she likes to cook, it was her dream in life to have a stainless steel refrigerator with a freezer on the bottom. At the time, it was the only kind that would fit into spot. One year ago, first the ice maker leaked causing water to spill onto the floor. Since I am a mechanical whiz I bought the part for about $30 and fixed it myself. We were happy.After two years, the freezer worked, but the refrigerator part went warm. I had a repairman replace the control box for $100. It still didnt work. We called Whirlpool, and they said the warranty expired, but as a courtesy, would charge me $95 for a service call. That was not acceptable. They told my wife that the products were man-made and are prone to mistakes. I replaced the fan myself for $100, but drove a total of two hours to get the part since it was rare. It worked great. For one and a half weeks, we were happy. Then the refrigerator and freezer DIED. Only the light and the fan worked. We bought a old school used GE top freezer, but at least it is stainless steel. We lost $2000 in two years and the people at Whirlpool refuse to do anything about it because it isnt their problem. Worst refrigerator EVER!!! !

Purchased the washer 11/26/12. Did not get extended warranty.... big mistake. By 12/1/13, control panel went out. Serviceman assessed ($100 service call). Quoted $495 to replace. ABSOLUTE JUNK! So very sad and angry that there is no recourse with Whirlpool.

I bought the Ikea dishwasher (model IUD8500BX1) in 2014. Because it’s from Ikea, it has 5 year warranty. I was using it daily, as I have a family of 5 and we cook and eat at home most days. I have called Whirlpool at least 4 times according to the repairman that was here today. Ive already had to replace the pump because it was holding up water. After which, mold started occurring in the washer. The technician who came out found 4 fault codes on the machine. He was prepared to replace sensors and the circuit board for the heater and the pump, since it likely had mold. But Whirlpool says the parts are functional therefore the replacement parts won’t fix it. He is not allowed to replace anything.Considering the mold is an after effect of the failure to drain, you would think they would fix the mold as well. A replacement dishwasher would be nice, but at least replacement of the internal plastic parts that I cant clean. Instead, they tell me to bleach wash it and run a cycle with bleach. Guess what, Ive already done that. And according to the technician hes never seen a dishwasher have this much mold when it’s used as often as I use it. If you are buying this product thinking they will stand by their product, think again.

I have had the Whirlpool washer for almost a year. It has multiple settings for different types of laundry, i.e. towels, bedding/bulky, colors. It is intuitive. My husband is able to put laundry in and is able to figure out which cycle to use. The tub is roomy and holds large items well. The dryer I just purchased in the last month or so. It matches my washer and so far I love it. It has very similar settings that match the washer. The lint filter is very effective, cleaning after each load is highly recommended. It dries quickly and is quiet.

I replaced my 12 year old Whirlpool double ovens with the current Whirlpool double ovens. The new 30 built in double ovens have been re-designed to vent the heat below the lower oven. The ovens come with a part that pushes the heat down instead of straight out. My built in ovens have a cabinet drawer below and after using the ovens just 4 times over the holidays I noticed the heat is damaging the finish. According to Whirlpools service center I should have checked on that before buying/installing. They told me to stop using my ovens, that this is a fire hazard, but they are not responsible. They do not have a solution to this problem. This is a poor design on their part. There is a disclaimer in their installation booklet that came packed with the ovens that the installer gave me. It says the cabinets need to be able to withstand the heat of the ovens. The cabinets can handle the heat of the ovens, just not the hot air venting directly onto the cabinets below the oven. Where does one find cabinets that can withstand 400 degree heat being pushed directly onto them? As a customer I did not have that information until after the ovens were installed and it was too late to purchase another brand.

Installed in May 2007, paid $674 for GU2455XTSS1 Whirlpool Dishwasher. It required service in March 2009 for $158 It became noisy in Oct 2011, so I placed a service call for $136. It was very noisy in Jan 2012. Again, I placed service call for an additional $93 that Whirlpool has not reimbursed. I must now replace the motor quoted at $403. The motor has a 90-day warranty. The 4.5 year old dishwasher must now be replaced. Whirlpool has not responded to email and to registered letter requesting a cost-effective solution to repair dishwasher that recognizes that reasonable life of the unit should be 10+ years and not 4.5 years.

We purchased a Whirlpool Gold Dishwasher about 8 months ago. Immediately called for service as dishes did not clean after running over 3 hrs. Was told it is operating as designed. I followed all the tips and it still continues to not clean. Plastic wear and cups stay wet, plates arent clean. We have changed detergents pods as well. We may junk it and buy something else. Recently purchased clothes washer and did not buy Whirlpool. Very, very disappointed. I should have kept my 12 yr. old GE Dishwasher that wasted water... But cleaned my dishes. Not happy with Whirlpool!

2 years ago, we remodeled our kitchen. We replaced with all Whirlpool appliances. WHAT A MISTAKE! Our ice maker went crazy 1 month ago and now our dishwasher almost caught fire Memorial Day weekend while we were away! Thermal Fuse and stainless interior prevented us from losing our house to fire but really Whirlpool, you spend that kind of money and all appliances are breaking before theyre even 3 yrs old! My husband is very good at fixing things but when he diagnosed dishwasher, he said he has to find a way to fix wires in control panel because melted insulation. Now I am afraid of it. So if you purchase Whirlpool, expect maybe 2.5 to 3 yrs service and think of them like a disposable lighter, use it and throw away.

I would like someone to explain to me why the control panel I.e. brains of the dishwasher which is around water is so sensitive to WATER. My daughter is the owner of the house and purchased this dishwasher last summer (2016) and within weeks we were having issue with the sensors. This supposedly was not covered under warranty (it was a WATER ISSUE). So now a dishwasher which cost over 700.00 is a door stop!! Where is people’s common sense... yes Im over 60 years old and very frustrated with the money that was spent for such an inferior product. Imagine having a dishwasher sensitive to water. The people who made it should give their heads a shake. Frustrated grandmother.

We bought the Whirlpool Gold Stainless Steel dishwasher around 4 years ago and the pump and motor assembly went out. We spent top dollar on this dishwasher and should of lasted a lot longer. I’m no longer going to buy anything Whirlpool makes.

We just wanted a black, good looking microwave, so far so good. It been easy to keep clean and cooks food fast. We actually installed it ourselves and it was pretty easy. It hasnt broken down or given us any struggles.

Purchased a Whirlpool WRF990SLAM fridge in 2013. Ice maker went out and the evaporator. Service tech said he needed permission from Whirlpool to work on. Would definitely not recommend purchasing this brand.

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

I dont know how anybody could write a good review on this machine. It always requires deep water wash and sometimes two cycles to get clothes clean. On regular cycle, it doesnt get water on all clothes. Oh yes, it does save water... Ive pulled things out with dry areas on them.

I bought this washer thinking it would last me for a long time. And now it wont wring out my clothes and I just wanted to say I am disappointed in my Cabrio Washer.

This washer has been a lemon since the day we bought it. Always leaves marks all over dark clothes. Had to have a part replaced before we owned it a year & repairman from the company said they have to replace that same part every time they go out so they carry them on the truck. Latch broke after owning it for less than 2 years & now it no longer spins water out of clothes. All this & we havent even owned it 3 years. I had a GE washer for years when I first got married & had children. Never had problems like this. Paid it off on Monday & on Friday it became a piece of junk. How is Whirlpool getting away with this misrepresentation? I dont even see how they can call it a washer.

I purchased a Whirlpool dryer about 18 months ago. Within 2 months the timer went out. Of course I am still under the manufacturer warranty they came and fixed it. Now a year after the same problem occur. Whirlpool convinced me to buy and extended warranty for $268.00 and scheduled service with Platinum Factory. Took a day off work, then they call me to cancel the appointment. I will advised people not to buy Whirlpool appliances because that is not the appliance I have with them. All whirlpool appliances have a defect. My refrigerator, my washer and dryer, my microwave all have issues. Most of the whirlpool at all. Services agents are rude and not professional. One agent from Tennessee had the nerve to tell me I have to lose money to get services right. When asked to cancel service plan I was told to write a letter to get my money back. My advice if you are in the process of changing your appliances DO NOT BUY WHIRLPOOL APPLIANCES because your problem will not be resolve by talking to those stupid agents and will not let you talk to a supervisor.

Just bought 4 new whirlpool washers and dryers for my new four plex I am building for clients. Two of them leaked violently along the wall and downstairs. Did I see they were BRAND NEW. Total garbage. Now I have to pay for servicemen to come and fix it. NICE AND THANK YOU for your poor quality commitment. Now my clients are pissed off because they cant move in because whirlpool makes garbage material. So the extra cost it has cost me is totally unthinkable. Whirlpool, ask me if will buy from you again. Thanks for ruining everything due to your inconsiderate quality levels.

I have front loader, Ive left the door open after washes, run cleaning cycle once a month, never had any issues, like with anything. If you take care and service it regularly it will last a lifetime.

My fridge is over 10 years old and the compressor has not failed. I have replaced some of the bins that have cracked or been broken over the years. It is a side by side in black color and will probably replace it with another type but the same brand as long as it is economically feasible to do so.

In 2013, my husband purchased a Whirlpool Hot Water Heater model #E2F40RD045V 40 gal. from Lowes in Vancouver, WA. On 12/12/15, had to call a plumber, the hot water heater was intermittent hot/cold. He flushed it, checked all power connections and changed the elements. On 3/18/16, NO hot water. Having a 6 year warranty, I called Whirlpool. They gave all kinds of excuses and told me to try a bunch of tests. By the time I got back to call them they were closed. I called them again on Monday 3/21/16 and said nothing worked and it had popped the breaker. They said change the elements. I told them I had just changed the elements 3 months before. I told them it was faulty wiring. They said the top element must be faulty. I gave up at that point and called the plumber. He came right out the next day. I had purchased a Rheem hot water heater to install and asked him to check the Whirlpool hot water heater elements he installed before he removed it. That is when it was discovered that under the insulation around the bottom element it was all scorched from FAULTY wiring. I called Whirlpool again and told them I could send them a picture and they said dont bother and immediately gave me an RA to return the hot water heater to Lowes. I told them I had already purchased another hot water heater and it was not a Whirlpool. I am going to request a refund.

We purchased this washer on 2008-04-27. It ran okay until a few months ago when it began making strange intermittent noises. This is now happening more and more often. I reviewed a lot of websites and see that this is a common occurrence for Whirlpool Cabrio washers, and Whirlpool will not stand behind it and make it right. Im going to write them a letter mirroring what Im saying here, and remind them that other appliances in my house are coming due for replacements or upgrades. Whirlpool and its affiliates will not be part of those upgrades going forward. I have no patience or tolerance for expensive **, which is what they put out here. I will have to purchase a replacement washer since this seems to have two major areas of failure, both extremely expensive to repair. I might check out Roper and see what they have--its apparently very well rated by the folks that work on these things.

I bought a Whirlpool water heater a few years back and have had nothing but headaches replacing the thermocouple every 1 to 3 months. The last one only lasted for 4 days. I did have a small flood in my basement well after the problems began. There are no visible signs of water damage to the unit, but Whirlpool has dropped my warranty completely. They sounded like they intend on not helping me anyway.

Refrigerator model # wrs325fdam04 - Refrigerator shelves and drawers are made of flimsy material. Water dispensed is never cold enough - almost at room temperature. Every six months one has to change the water filter cartridge, Filter1 w10295370a, which costs at least $49.99. Cheaper versions that cost 50-60% less, I have purchased and returned 2 different brands, are not compatible with this refrigerator. I do not recommend this refrigerator.

Because the lid was not thoroughly covered, painted and sealed, it began to rust within first year. When I contacted Whirlpool about this - they were not only rude, but will not support quality issues with their products. They basically said they did not care and even acted like a consumer should expect such things! Actually said because its subjected to high moisture levels. WRONG, I do NOT just expect rust. It only formed due to poor quality paint job and was not cured correctly. My Kenmore washer and dryer both, were 25 years old and had zero rust and still functioned when I replaced them with these Whirlpool. Its frustrating that there are no quality, American made products anymore.

Bought Cabrio 3 years ago, started getting ul code and f1 code. We leveled machine, but cycle kept getting stuck mid-cycle. Called repair guy, they say it is going to cost between 6 to 800.00 to fix???? Really. Its three bloody years old. Very disappointed. Do I now get it fixed or break down and buy another washer. I would not buy Whirlpool again. Very pissed.UPDATED ON 02/05/2015: We called an appliance repair company and initially paid $440.00. After installing a motherboard computer system, it still did not work. We were then told that the other part would be another $120.00. We were already soaked for $440.00 so we decided to pay. After that was repaired the washing machine was still stalling mid cycle. We were then told that it has something to do with the wiring and it would cost another $120.00-$140.00. Needless to say, we declined. Complained to whirlpool that machine was three years old. We are pissed and $570.00 out of pocket. Just bought a lg front loader and paid for a 5 year warranty!!

Bought this washer 5 days ago!!!! Broke after 4 loads of laundry. Store manager says they will deliver new washer. ERROR CODE LD LONG DRAIN and heavy duty humming sound. Unplugged washer to prevent further damage to washer and reduce risk of electrical fire in home. Consumer affairs wants me to rate my experience - rate my experience on what? Ill give 4 stars dissatisfied here, but field wont let me go more than 2 stars. If its this website they want me to rate I give 2 stars dissatisfied, as for the washer, dole out 7 Benjamins for a product that dont work and you tell me!

The features on the washer is a wider size wash basket, no non-snag agitator with 5 load size choices, 5 water temperature choices, type of wash includes soak, quick wash, normal, deep water, heavy duty, bulky, hand wash, gentle, some other choices Along with a choice to wash your machine, one rinse or two rinses without fabric softener, one rinse or two rinses with fabric softener. And finally a selection for Pre-soak on or off. Also has a 3 light display for what it’s doing, lid lock, pause, cancel and start button. It’s an HE. Clothes come clean.

I owned a Maytag washer for 30 wonderful years, so I of course bought a new one. I have battled with my Maytag (Whirlpool) front loading stackable top of the line washing machine for 2 1/2 years. It will not drain, yet sometimes it will. I have played every game with this machine to figure why. I had a repair company out 5 times while it was under warranty and they could never find the problem. It is totally unpredictable. If I could bill Whirlpool for my time and anguish I would own this company!They now say it is the computer board and I will have to pay $350 for a new service contract to fix the machine. I not very politely said that they should pay me for all my emotional abuse. They offered me another option saying they would pay for a service company to come out and look again. However, I would have to pay the labor and material cost. Since I have a stackable unit and it would take 2 technicians I would have to pay $90 for the second person. I was so mad that I called Whirlpool back and they refused to offer me that $350 charge and just said sorry. I are fortunate to have a lake house which needs a new washer. Guess what? It will NOT be a Whirlpool product. I wish I could go to the store where I purchased this holy terror and picket!

I purchased a Whirlpool gas stove model #WFG540H0AH from Sears in March 2103. Since that time, the oven has repeatedly broken. After two major repairs, the repair company said the fas venue (?) suspect board was defective and needed to be replaced by the manufacturer. After 3 weeks of back and forth calls with Whirlpool customer service, the only solution they provided was for me to purchase a new stove at a discount with no compensation for installation, the gas connection kit, or haul-away of the old appliance. The original stove cost me $1100 including the installation, haul-away and taxes. The replacement option would have cost me $800 and still did not included haul-away, the gas installation kit, or taxes. Hardly an affordable solution. Whirlpool at no time addressed that a part on the stove was deemed defective.

Front-loading does not do good job of rinsing. The Whirlpool Duet will not last longer than 2 years. Whirlpool recommends that owners purchase a new washer every 2 years. Whirlpool suggests owners purchase new clothes each week to avoid washing. Any owner would be required to quit their job in order to wash clothes. The Whirlpool Duet front-loader requires 12 hours per load. This means that only 2 loads can be washed in a 24-hour period. Each load requires 10 rinse cycles to remove suds.

Purchased a Whirlpool Cabrio Washer a few years back... Started getting F1 error message and just proceeded thru it like most did initially, but now has become pain in the rear just to do one load of laundry as we get the error 2-3 times when we start each load - then on every load w/ 21 minutes left on the cycle. From the looks of things online this is a chronic problem and should be fixed by manufacturer. I called Whirlpool customer service and first person I talked with said they understand it is an issue but no longer are any recalls or reworks on that machine. I asked to speak w/ supervisor and sat on hold until I got one. Was then informed they do know it was a problem but was not something they could do anything about other than schedule a service company to come take a look. I specifically asked if there was at one time a recall or if they were fixing this issue for a while. She said Yes, they took care of some of their customers but are no longer doing that for this model. So basically because I didnt call in at the right time I need to fix my machine myself. I said it will be the last Whirlpool or Whirlpool associated appliance I ever purchase if this is the kind of customer service I can expect... The supervisor just said she was sorry to hear that and to have a nice day. Hopefully enough people read these reviews as I wish I would have before purchasing my Cabrio and dont buy Whirlpool.

I purchased a top load Whirlpool Washer and Dryer in April 2021. When it was installed I commented about how noisy it was. I was told it was because it was empty, but it will be much quieter once you put in a load of laundry. That did not make any difference. I called Whirlpool customer service and explained I had just purchased it less than a week ago and it appeared to be very noisy. I was told they could send someone out, but if they determined there was not a problem I would be charged a service call. I said the machine is not even a week old why would I be charged a service call shouldnt this be a warranty issue. Again I was told there would be a service call charge.I am completely baffled at the customer service response. This is the first and only time I called. I contacted the store where I purchased both the washer and dryer and was told it should not be that loud, this is the first time anyone has complained about the noise level and there should not be charge. Whirlpool has terrible customer service and I will NEVER purchase another Whirlpool product again because of the customer service. I have purchased numerous appliances in my lifetime and have never been treated so poorly. If I could return both the washer and dryer I would not hesitate. I would not recommend Whirlpool to anyone.

Purchased our hot water heater in August of 2011. About 3 days ago, it just stopped working. Surely it should last longer than this, right? Nope apparently I was taken! We called the manufacturer and described the issue. They said it was the thermopile. They could send us another out in a few days but we didnt want to wait so we paid $50 for a new one we were able to locate at a hardware store. Nobody sells these! We replaced the thermopile but no results... Pilot will not stay lit. Called Whirlpool back and they said to hit the reset button which we did. Called a technician (several) which wouldnt touch the heater. Said nobody works on these because they are riddled with issues. I pleaded with him to test it which he did. He said the control box is out! He said to cut our losses and buy a new one! I am so very upset! I cant afford another one! We called Whirlpool back again to see what they would say this time - they are sending us another control box! After reading all of the complaints and being without hot water, I am not hopeful of a good result! I plan on replacing the control box that they send and then saving for a new heater! I want my money back which Ive heard just wont happen! I have also had nothing but issues with my gas stove made by Whirlpool ever since it was only 6 months old. STAY AWAY FROM WHIRLPOOL PRODUCTS!! Run!!!

Bought a new Whirlpool range in 10/20. In 06/21 the control panel stopped working. Now they say the necessary part will not be available until 10/21! 5 months without a working range! Dont buy Whirlpool--shoddy products and terrible customer service.

Whirlpool® Gold® 5.8CuFt Capacity | GAS Stainless - This was not an inexpensive stove. The self cleaning oven function is a total failure. You are not supposed to use oven cleaner on the glass, it now has obscured the view into the oven. The top of the stove is very difficult or impossible to clean. The knobs are a dangerous issue. They will fall off at the slightest touch and the stainless markers around the knob are just a stick on label. The oven temperature is not accurate. The bottom drawer is completely rust spots on the inside. What more can I say. Oh I know. Whirlpool your quality is a disgrace and I want a refund.