Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

Whirlpool’s WFG505M0BS is a reliable gas range. It doesn’t have a lot of bells and whistles (no self-cleaning mode or convection oven), but it’s also not priced as such. If you’re looking for an appliance that’s sleek, smartly designed, and quick to heat up, it won’t disappoint.

We purchased Whirlpool Gold Accubake, double ovens (gas) in 2005. Since then, we have experienced identical failures (8 to date) during the self-cleaning cycle in which the high temperature burns out the thermal fuse of the ovens. This requires two Sears technicians to repair the unit (it requires two technicians to pull the oven out as the fuse location is in the back of the unit) and leaves us without use of both ovens for approximately 2 weeks (scheduling parts delivery and technicians through Sears home repair is not an expedient process).After checking other consumer product websites, it has become clear to me that there is a known design defect with these ovens in which the thermal fuse is not adequately insulated from the high temperatures during self clean; it therefore trips and burns out during the self-clean cycle. While not having access to ovens for about two weeks/year on average may sound acceptable to Sears, the reality is that the problem has escalated in frequency since purchase. In 2013, we are going on our third repair of the same problem (that makes 6 weeks of non-usable oven time in one year) and Sears will not consider replacing the unit, despite: 1) our obvious dissatisfaction with a lemon unit, 2) a well documented history of the defect with this particular Whirlpool oven and 3) an ongoing and escalating repair cost to Sears (it is under their extended warranty so the repair cost is on them although we did pay for this service up front on our appliances).I would stay away from not only Whirlpool appliances but also Sears as there doesnt seem to be any regard for the customer experience and taking care of a product problem (the right way) with a known defect. Sears has an opportunity to make this problem go away quite easily and retain a customer - fix the problem permanently or just replace the defective unit. Unfortunately, my experience to date with Sears standing behind the products they sell provides me with little confidence that either will happen.

We bought a new washer and dryer back in August. We have always bought Whirlpool. Whirlpool (or the government) now is trying to save the planet by regulating the water level in your washer. The water levels are so low your fabric softener & soap leave lines on dark clothes. IT SUCKS! It does not clean like our old washer. Very dissatisfied and would love to return it and get a washer where you can regulate your own water level. Its unbelievable that a manufacturer can make decisions for the consumer like this AND sell this feature which you PAY MORE FOR. TAKE IT BACK! Ill never recommend this product to anyone.

Machine just will not clean clothes. Model Cabrio W10560169A. Company offered NO support. This washer retails for around $1,000 and just does not work!

This washer is a piece of junk!! It doesnt use enough water to clean the clothes and now it wont spin them dry. I have maybe two loads a week on a regular basis. I have always used HE detergent. Never overload. It is only three years old and I have been having to go to the laundromat because I cant afford a service call and especially if it is what they say which costs almost much as the washer. Be ahead to buy a used washer or a cheap one. It wasnt getting the clothes spun out dry enough - dripping wet. Then it flashed od and ul and sd and f51 and then it kidnapped my clothes - couldnt get the door to unlock with the pause or power until I unplugged and still had to wait several minutes. They refuse to help. Do not buy this machine!!! The customer service was not one bit of help. Instead she wanted to charge me $350.00+ dollars for some plan.

Whirlpool double oven. The electronic control board has been replaced twice and needs to be replaced a third time after less than a year. The thermal fuses go each time I run the self clean. Whirlpools response has been disgraceful, trying to blame the problem on faulty installation when thousands of people have had the same problem. Ignore ANY US companys product; their warranties are worthless and they repair, not replace. My next oven will be European because in Europe they have to automatically warranty for five years any consumer durable. Consumer Reports ratings are worthless since they dont include breakdown experience in the ratings. Never buy anything from Whirlpool. They sell rubbish and dont honor their own warranty. Check the BBB rating. My brand new double oven broke down the first time that I ran the self clean cycle. Whirlpools response was to claim that the cutout opening was 1/8 inch too narrow and therefore they would not honor the five year warranty that I had bought from them. This was a lie, as I verified the width and it was exactly that required. Others have had the same experience. Whirlpool also makes Maytag, Kitchenaid, Kenmore and Ikea.

Whirlpool 70328 215 IMFRESH ROY 5S purchased on 14th Feb. 2016. It has stopped cooling on 11th April 2016. Complaint lodged on 12 April. No serviceman attended and not connecting toll-free number. Never, never go for a Whirlpool refrigerator.

Purchased washer and dryer combo on 07-08-2013. I have a family of just 2 now. Under normal conditions I thought the machine should last 12 to 15 years. After 2 years of service the bearing and seal on the tub failed, I had to order parts and rent a tool to install. Then after 3 years had to replace suspension kit for the tub. Now after 3 1/2 years the water drain pump has failed and the sensor on the motor is acting up. This machine listed for $800. I did not purchase extended warranty but I have repaired myself. If I had not repaired myself the cost would have exceeded the cost of new. I have now purchased another makers model machine. I think Whirlpool should buy this machine back.

Refrigerator model WRF560SMYH purchased 22 months ago will not defrost automatically. When ice builds up on the back of the bottom mounted freezer, it creates a terrible noise. Only quiets when we manually defrost the ice with a hair dryer!! 4 service calls from the warranty company has failed to solve the problem.

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

July 2017 I purchased a Whirlpool refrigerator Model # WRF757SDEM00 S/NK51709722. The refrigerator portion went out, the repairman said it was the fan therefore I spent 351.00 dollars for house call and fan. When that did not work the repairman spoke to whirlpool and they said the panel of small computer may go out with it 212.00 plus tax. Did not allow that and tried another repairman who said the value that switches from freezer to refrigerator was out and if I could find someone to fix it would cost between 600 and 800. I went out and bought a Samsung because on the front said 10 year warranty. At least anything is better than 1 year whirlpool offers. There is NOTHING in the name.

I do like my Whirlpool refrigerator, but it started to not cool things anymore. I had to get it fixed. The professional I had come out to fix it said that these particular Whirlpool models didnt have a specific part they they needed. It also got built up with ice that needed to be broken down. Overall, I wouldnt buy this model again, but that doesnt mean that all Whirlpool refrigerators are bad. Just this particular model.

My stove hasnt been a problem from the start. I have had to buy two parts one for the oven, and the top. I feel my stove is dangerous. I would not buy a Whirlpool again. I would like to know who makes the stove that dont costs a arm and a leg. My stove is less than five-year old.

The broiler came on its own during the night. We went to bed at midnight. 4:30 in the morning woke up to a smell, the broiler was going wide open. It had melted the handle off the front of the drawer. There are cookie sheets in the broiler. We dont use it, we have never used it, it was so hot Teflon on the cookie sheets burnt off. The side of the stove was so hot I couldnt touch it to get behind to turn off the gas. It almost burnt my house down. The carpet and the wall are black in the back.

Love my Whirlpool stove and I just bought a Whirlpool French door fridge. I also have a Whirlpool washer and dryer and I am very happy with the way they work and look. I replaced my Tappan stove that I had for quite a while and it was a good stove but I am very happy with my Whirlpool stove, it not only works great but it looks great.

I bought a Whirlpool model GI7FVCXWY00 over and under refrigerator directly from Whirlpool through DirectBuy on April 19, 2010. The unit was a relatively high-end model (over $2,000) that came with a 12-month warranty. Thirteen months after purchase and 1 month after warranty expiration, the ice maker stopped working flooding the kitchen in the process. We called Whirlpool who recommended one of their authorized maintenance subcontractors (GuinCo) to appraise the problem. GuinCo came out, diagnosed that a valve in the ice maker had gone bad and the repair cost us $364. We chalked that up to Murphys Law (repair needed immediately after warranty expiration). Not 4 months later, the kitchen comes up flooded again and again and the ice makers not working. We call GuinCo, the repairman come out and said this time that its a heater and ice maker defect which will cost $643 to repair. He also said that the unit has been designated as having a design defect. We held off on the repair until we could contact Whirlpool for some remediation since it has become obvious that the unit is a lemon. I called Whirlpool, laid out the problems, timelines and potential cost (ice maker failures are going to cost us almost half of what the entire refrigerator cost before the unit is a year and a half old) and the only response they had netted out to was: Sorry, you should have had extended warranty. This is a prime example of an American manufacturer, marketing an inferior product and offering the customer nothing when the lack of quality becomes obvious. I will recommend to anyone I know to stay as far away from Whirlpool products as long as I live.

We bought a new Whirlpool refrigerator about three years ago. Because of space, we had to purchase one with a top freezer and also with no ice maker. First of all we didnt realize it was much deeper than our old Kenmore so it stuck out further into the kitchen space. That was not that big of an issue. At first everything ran great including the top freezer compartment, or so we thought. Then we noticed that when we had ice cream in the freezer and put water in ice cube trays to freeze, the ice cream would get very very soft. This continued to the point that now anytime I put water in there to freeze ice cubes I have to turn up the temperature to keep the ice cream frozen. Once the ice cubes are froze, there is no problem, but they take at least six hours to freeze. Then one day when a young child slammed the refrigerator door closed, the freezer door popped open about an eighth of an inch and then closed again. So, I tried it. Anytime you close the refrigerator door a little too hard the freezer door pops open. I then tried the dollar bill test to check the strength of the seal. The bill pulled right out of the door with very little effort. So, is the problem bad seals, bad design, or bad quality control, or what. How can I be assured that the frozen foods in the freezer are being frozen as solid as they should be. I know they dont freeze solid enough in the freezer door. I will eventually dump this refrigerator and go get another Frigidaire. If we have to get one with a bottom freezer, we will just have to rearrange our kitchen to accommodate it. But, having to turn the temp up and down every day is ridiculous. I have had issues with food close to the walls in all refrigerators slightly freeze, but never had an issue with keeping things cold enough. I will never buy another Whirlpool refrigerator, stove, or anything else for that matter. I have always had good luck with Frigidaire, so I will stick with what I know works.

Strange bear like sound when it washes. We stopped it and on again, sound gone. Water on full water pump drain attitude ok. Big lid (grey) inside on. Ran some time water draining with tablets to make it clean and run better. Had someone to look for it, no sound. But when we now turned on, it sound like a mumbling high sound from inside machine or upper lid. We have some thermostat error a few times now. No hot water condition and no washing in high temperature. Håkon ** was the inspector of this strange thing happening. Could this be dangerous to let it run?

Dishwasher leaking thru the diverter motor; apparently the gramet # WPW10195677 gets worn out and starts leaking. They have discontinued the part and can no longer be found. I call Whirlpool and all Parts supplier in my city. Obviously this is something that happens with time (5 yr old dishwasher) and is something very simple to change. But if we cant find the part....what are we supposed to do. Also my dishwasher rack has broken 2 years ago and is holding with zip straps! Horrible product!

The first day I set foot in IKEA changed my life, innovative and sensible and affordable. Some years later I had the opportunity to remodel a kitchen and I immediately thought of IKEA. I used their online planner, researched the appliances and knew that they were made by Whirlpool and that they offered a kitchen package discount if I bought 3 or more appliances with all the cabinetry. So I hurriedly designed the entire kitchen from top to bottom with IKEA.Included in the design was my center piece, my 5 burner Praktfull Pro Gas/Convection oven range with stainless steel backsplash and top of the line hood fan, basically a thing of beauty! I loved it and I visited the store several times to look at it. I finally bought everything, and installed it. Absolutely the most beautiful kitchen in the world.We have a historic building and were on several historic tours, interviewed for the newspaper, our kitchen was the highlight of the tour. My gas range drew oooos and awwws. The range is an exceptional appliance, beautiful and amazingly efficient, easy to clean…I was in love. Then one day it happened, the love affair was quickly over, devastatingly over. The door fell off the oven and the hinge broke! Yes you heard me right, it fell off, but that is not the worst part. It appears that not only are there no parts to fix it… there IS no fix for it, period. The door fell off because it had been glued on!!! Yes glued on. Whirlpool and IKEA had actually manufactured an appliance that failed in less than 4 years of use and no apparent intention to ever provide service or parts for it. This is criminal and they should be fined for their neglect of the customer, their calculated malfeasance and fraud to the customer.So my beautiful kitchen has a big black angry cavity in it and now I must try to find a new range that will fit in the opening left by this piece of junk and also pay probably over $2,000 to $4,000 for it. Most of all I am heart broken, mad and distrustful of anything IKEA in the future. Oh and by the way, my entire house is IKEA, my living room, my patio, my bedroom (s), my library, my office! Ive spent thousands and thousands of dollars at IKEA. No more! THE FINAL INSULT: Ironically…. my kitchen was featured on the IKEA website!!!

We bought a Whirlpool washer (Model # WTW4900BWO) and dryer (#WED4850BW) and within 2 months I was having problems with the washer AND dryer. Every time I washed a load of clothes, the clothes would have some yucky stuff hanging all over it. I called Whirlpool and was told to try setting the washer on 1 Rinse with Softener even though I never use a liquid softener. Their suggestion did solve the problem, but why doesnt a brand-new washer work the way its supposed to? A short time later, my dryer buzzer stopped working and the knob would not advance when set on the Energy Preferred setting. I called Whirlpool again and was told they did not have a service technician in the area where I lived and that it was not likely that one technician would come on the same day to service both machines. I asked why they would sell their products in an area where they were not willing to service them and they said that is the choice of the store that sold it to me. Then they told me there was a service technician available about 40 miles away and they would fax the order to them so they could contact me. The technician who came did look at both machines and was able to determine that the control panel needed replacing on the dryer, but was not able to do anything about the Rinse Option problem on the washer. He suggested that I continue to follow the recommendation of Whirlpool as long as it works. I can do that, but Im not happy that a new machine does not work the way its supposed to. He also recommended NOT using liquid laundry detergent or fabric softener in my washer because it contains animal fat and can build up and cause problems. Nowhere in the manual did it say that. He took the washer apart and showed me how it was already building up under the washer basket. I told the technician that my laundry has had an unpleasant odor to it when it comes out of the washer and even after it is dry. He said that might be because of the small amount of water that is used in the energy saving washer. If these problems cannot be resolved, I consider this washer to be a lemon and hope it will be replaced with a new one. If I had to do it all over again, I would buy a traditional washer. I liked the idea of conserving water, but not if my familys clothes stinks.

I bought my Cabrio Platinum Washer and Dryer in 2013 (4 years old). About a month ago, it started sounding like an airplane was landing in the house while on spin cycle. I called a repairman and he said the bearings were going bad and it would be better to buy a new machine. When we pulled out the washer, there was grease all over the floor - apparently a seal started leaking and the bearings had no grease so they started burning up. I talked with Whirlpool, after all it was only 4 years old and a seal leaking and burning the bearings up wouldnt be from normal wear. They were not convinced and offered to give me a discount on a new one -- No Way! I went with another brand recommended by the repairman. The screws on the dryer door also came out and we had to replace them. So much for the Whirlpool brand and especially their top of the line machines. I will not buy another Whirlpool washer or dryer.

We purchased this machine new and took delivery on 5/21/11. We did not start using this until late August of 2011. In late November we noticed a loud noise from the washer. When we contacted the sales company that sent out a repair person who informed us the bearings were defective. We have been told the parts are on back order for another 2-4 weeks. It has already been 4 weeks since they were out. Whirlpool was no help. They first claim we must have overloaded the machine, then relented saying that things happen. Either way I am without a washing machine we paid $1000.00 for another month; yet they will not extend my warranty at least for the time my machine is down. I am now worried about the damage that this unit may have caused to my new home due to water leakage, let alone the added expense to due my laundry since I must now use a service to provide for a washing machine I own.

I have had the washer for 3 years now and it started to make a loud noise during spin cycle. I made a service call and found out the bearings are damaged. Something that cost this much money should last a lot longer. I have researched on the internet and found this to be the problem for a lot of consumers and would like to see something happen.

We purchased this machine a couple of years ago... What a disappointment! Was recommended to me by the sales person and I trusted her. The machine does not get our clothes clean!!! We are a couple in our 60s so our clothes dont really get dirty most of the time, but they come out with marks on them all the time. My dish clothes and wash clothes are a disgrace! Im continually trying to soak them to try and get them to look clean. Ive been going to write this review for a long time, but today was the final straw. Washed a small load of towels and had to rewash several pieces! I would never recommend a Whirlpool product after this experience.

Bought a built in oven August 30, 2018. Oven stopped heating two weeks before Thanksgiving. Repairman fixed it. It is not working again, two weeks later. Bought from Best Buy. They will not take it back. Whirlpool will not replace it. UGH!!! $ 1,600 down the drain. Will no one help?

I hate this machine. I stress whenever I have to do laundry. The worse machine I ever owned. Stay away from it. It is a total rip off... I wanted to replace my front loader machine with a top loader. Based on good reviews at the time I purchased the Cabrio. Nothing gets clean. The detergent stays on the clothes and unless I use the Bulk senor. Otherwise I get horrible white marks on all the dark clothes. I cant even get the marks off with a wet rag. So washing only a few items I have to use Bulk. The sound is so bad from the machine, my dog runs in the closet and shakes. I feel so bad for her. How can a popular name like Whirlpool make such an inferior product? They dont even stand behind it. Customer service stinks. Never will I buy a Whirlpool product again. Now, I am trying to save up to buy a new machine. Shame on you Whirlpool.

The oven continues heating up even after it reaches temperature. This happen soon after we purchased it in 2009... When I called Whirlpool they said to unplug the oven for 15 min & allowed it to reset. This worked, that time. It has continued to happen to the point now where it will not reset and then we can no longer use our oven.

In 2002, I purchased an EE3Z50RD055V 50 gal. Whirlpool hot water heater. Recently several solder joints on the computer module became unsoldered so I cleaned the joints and resoldered them. But several months later another joint became unsoldered so I thought Id just purchase a new module. I called 1-877-817-6750, explained the problem to the young lady. She informed me that they would ship me a new one overnight. I asked her how much this would cost and she told me there would be no charge as it had a lifetime warranty. SURPRISE! Thats what I call customer service! A few years ago, I purchased a Whirlpool Duet front load washer and dryer. Now Im twice as glad that I did. My wife and I LOVE the Duet.

I bought a washer dryer Cabrio set and the washer after 2 years has a bearing failure and is squealing badly. The service technician quoted $400.00 to fix a washer that cost me $800.00 new and is 2 years old. I had a Whirlpool washer and dryer set for 11 years with minimal issues and that is why I bought Whirlpool again. This will be the last time. It is a matter of time before the washer fails and I will have to purchase new or pay the service technician.

I purchased a Whirlpool WFW9050XW washer in Aug 2011. I have had nothing but problems. Sears sent repair tech 2x; it would work for a couple months and stop. Whirlpool has sent new motor, tub, switches, etc. I feel I bought a lemon and I want Whirlpool to replace the machine.

I am writing to you all today to urge you to not purchase Whirlpool products specifically Whirlpool 2-cu ft High-Efficiency Front-Load Washer. I purchased a front loader washing machine for our tenants through Sears back in June of 2013. When it was hooked up it had an error code on it so we contacted Sears and 3 weeks later they sent out a repairman telling us it needed a new motor (this machine had not even washed 1 load of laundry). They ordered the part and Sears paid 1200 to replace a part on an 800.00 washer.....yeah I know dumb right. Well the part replacement did not work. (Surprised) They ordered and delivered a new washer 1 month later....same error code. Lets try again with another washer......same error code. How about another one......water would not stop running into the machine because the sensor was broken. Wait we are not done how about another one.....same error code. No I am not kidding, 10 months later 5 washing machines and my tenants have yet to have been able to wash a single load of laundry. I have been reimbursing my tenants every month for not having a washer for the past 10 months. I finally had Sears reimburse for the washer which they will pick up soon. I am out all the interest for the past 10 months for a product never used. To top it all off I called Whirlpool directly to see if they would be willing to at least give me a coupon for any amount toward the purchase of a different washer. They told me quote We dont do anything to compensate our customer for their troubles. That is the icing on the cake folks!!! I will never purchase another Whirlpool product and I encourage you all to not as well. I want to show them how not caring for their customers can impact them. Please share if you can, but more importantly please pass the word!!!!!

Purchased heavy duty dual steam washer and dryer in 2008. Recently got some error codes that we could not fix. Had one service company come in and they could not figure it out. Had a certified Whirlpool company come in and they could not figure it out. They called Whirlpool technicians and they were even unsure of what is wrong. Said they could keep ordering parts and trying them to fix the problem. And of course I would be responsible for the parts. And no guarantee it would be solve the problem. Called Whirlpool direct, to no satisfaction. They said they could send the same company out and have them call the tech line while on site and try to troubleshoot the problem. However, would have to wait another 3 days to get him out. Been a week without washer. I have had washers bought previously last over 10 years without any problems. If these machines are breaking or control boards are going out after about 4 years, then Whirlpool has a bigger problem. Whirlpool supervisor was only offering to maybe a discount on the parts needed, without even knowing if they could fix the problem. Seems to me like they really dont care. Very dissatisfied, will definitely not recommend this product to anyone. And if it ever gets fixed, I am going to sell them immediately.

I purchased Whirlpool Refrigerator model WRF989SDAM02 in June of 2014. I began having problems with the ice forming into a solid block shortly after having the refrigerator installed. I called for service several times over the next year trying to rectify the problem. Once the warranty had expired I continued upon the advice of Whirlpool Customer Service to schedule their certified Technicians to work on the problem. A year and a half and several hundred dollars later I am still unable to get ice cubes when desired.Ultimately I was advised that I would need to use the ice maker once a day to keep it from forming into a block. When this didnt solve the problem I again contacted Whirlpool, had another of their recommended service technician come and give his advice. I was told that the ice maker needs to be in constant use or it forms a block and this is a defect in the design of this unit. A Pro Tech Appliance Inc. Technician, an authorized Whirlpool technical representative, said the only way to have usage of ice would be if I made sure to dispense ice a minimum of 8-10 times a day.This is completely impractical and just plain ridiculous. I contacted Whirlpool again. They refuse to acknowledge this is a defect in the design of this model. I have replaced all parts that can be replaced, had the unit resealed and have paid for multiple service call. Whirlpool will provide no remedy for this problem. Now that the unit is out of warranty they have refused to provide a resolution even though its issue began while still covered under the year warranty. The ice in the ice maker is completely unusable and melts into a solid block within 24 hours if not in continual use.

We have a large family so when we needed a new refrigerator we found this very large unit (Whirlpool 32 cu). About this unit, its not really all that wide, but it is very deep. Lowes didnt have a model on the floor but we went by photos. Also the salesman showed us a smaller version of this unit and we were impressed with the design. However unlike the unit we saw the shelves arent adjustable. They are preset. Also the ice maker on top is very small and makes ice very slowly. The freezer section ice maker is much larger. The main complaint I have with that is unless you push the tray all the way to the back ice can drop behind the tray and fall down causing the freezer door not to always close properly, leaving you with semi defrosted food. Whoever designed this refrigerator was an idiot. All issues are really related to design flaws. This is a very expensive refrigerator. I expected a great unit and got a piece of crap instead. Stay away from this model at all cost. It would be smarter to buy 2 refrigerators instead if you have the room. This model will give you nothing but a headache and grief.This is our story about our experience. This all took place within 1 year. We bought it at Lowes. They were wonderful when it came to taking care of us when it was within the stores’ warranty. They really tried to help us. Once their warranty ran out they put us in touch with our new repairmen. Lowes did tell us that one other man bought the same unit and he was up to refrigerator # 15. Like I said, this unit is crap. Our first unit was delivered with a huge dent in the door. They took it back (lucky for us we have 2 other refrigerators).Second unit arrived in store also badly dented. They didnt bother to deliver that unit. Third unit arrives at store but back area around motor all dented up. They order a 4th unit. This unit wasnt dented up so they delivered it. However doors were very off and wouldnt line up so it didnt close properly. A 5th unit was ordered and same issue with the doors. A 6th unit ordered and they called telling me that it was all dented up and needed to order a new unit. Our 7th unit arrived and in 3 days started making funny sounds. Dual ice makers stopped working and inside refrigerator is was very warm. Lowes ordered #8. This unit the freezer doors werent lining up so #9 was ordered. This time everything seemed to line up, no dents however by the third month it started making a funny sound. Dual ice makers stopped working. Warm inside the refrigerator section. Lowes sent out a repair man. He explained a design flaw was not enough insulation around the fan so it was icing up. That was replaced and it was working nicely for 4 months. Same issues with fan icing up, the noise and no ice. The repair man came out again and mentioned what was kind of a recall with the unit. The control panel in the back of the refrigerator was wrong and needed the correct one to be put in. That was done. He told us that we shouldnt have any more issues with it.Same thing again. Same symptoms, same results...we had to throw out hundreds of dollars worth of food. (I just put in an entire prime filet mignon I planned for a special dinner and had to throw it out. OUCH!) Awaiting for the repair man, again. He will be out in 5 more days. Im sure it will be a new issue, a new brand new fix and it will work for a few weeks to months and we will be calling him again.

This washer (Cabrio 6th Sense Washer) is less than 4 years old and now needs $500.00 worth of repair. You have to replace the tub in order to replace the bearings. If your washer starts to make noises during the spin cycle, you are in for a big repair bill. I still havent decided if I am going to repair it or junk it. The towels always smell sour even if you wash them twice.

No get this and the dryer used. Top of the line. I am having fun seeing all the choices. I would recommend because of the efficiency. Measures soap and softener depending on the load size. Like a miracle.

My mother-in-law purchased a Whirlpool refrigerator in 7/2010. It broke down the first time in August then consistently after that. We have had repair people out multiple times and the issue continues. I called Whirlpool and they said since it was purchased more than a year ago, it is not their problem. You would think that in all that time they would have found a way to repair or replace it. To make matters worse, we have had to call hospice in to care for my mother-in-law, all she wants is to get ice and water out of the door.

I bought a dual oven Whirlpool 2 years back. This range keeps breaking knobs that are such a poor quality. I have bought knobs from Whirlpool 7 times already then got PSEG home service and they are tired with the quality itself. Save your money and buy another make! Poor customer service and the worst experience is what I have gained on buying this make. Have old mother at home and this headache only created more issues to help her with cooking.

New stainless steel range 5.3 cu.ft. with convection oven delivered by Home Depot on time. Before the day was over the trim around oven glass was falling off. Double sided sticky tape was not holding. Yes its put on using double sided sticky tape. Called Home Depot, once you accept it, you deal with Whirlpool. They must first send someone to look and see. Yes its falling apart. Service tech will order new door. Mind you it will also have the sticky tape. We have also noticed that the glass top has many deep scratches, he will replace that also. A week later still no word, when. Used the oven because I couldnt wait and as it heated up smoke poured out of it and a loud noise from inside. Turned off and pulled out bottom drawer to unplug. Bottom panel had fallen down and undersides were rusted. Only had the stove 3 weeks and its Christmas Eve. Will read reviews first next time. No problems with my other Whirlpool appliances.

Bought the refrigerator in december 2017. Called them 2 times already and just called them again on sunday. They are coming out friday the 15th again to fixed a leaking problem. The first time was the freezer was freezing up a lot of ice which they claimed it was the rubber on the bottom door of the freezer was not sealing tight enough. Second time the refrigerator was leaking so much water I was literally drying up water everyday and have towels on the floor to prevent my new floor from damage. Leaking starts again same problem. Completely frustrated now. Going to contact Consumers Affairs to see what further action I can take.

I purchased a Whirlpool Duet front-loading washing machine on September 27, 2010. By October of 2011, it was making a loud grinding noise during any spin cycle. I called for service and was told I needed new bearings which entailed rebuilding the machine. I had purchased a 5-year extended warranty. I was originally told by the warranty company they would replace the machine.After waiting two months, and after several contacts made by me to the retailers customer service, I was told the machine would not be replaced, but repaired. After the repair, on January 6, 2012, the machine now rattles and shakes so much during the final spin cycles. It is literally impossible to have a conversation with someone standing next to you in the same vicinity as the washer, it is that loud. I am sorely disappointed with the Whirlpool line of products and with the retailer who has been dragging their feet on customer satisfaction.

We bought a Whirlpool Washing machine a couple of years ago. We have been having problems. It does not get the clothes clean and laundry has an odor to it. We bought it at HHGreg by the Dayton mall in Centerville, Ohio and also bought the extended warranty. It was the largest capacity machine they had in Whirlpool so I dont need to mention what we spent for this thing. We have had a service tech out 3 times. The first time he replaced a part. It still didnt fix it. So they were out two other times saying nothing was wrong with it. Not only is it not getting the clothes clean, but is putting lint pieces all over the laundry. The warranty place already said if they come out again and they cannot find out what is wrong, then we would have to pay for the service call. We then went to the store we bought the machine and talked to the manager. We got no help from him. All he did was throw us back to the warranty place. Not to mention, the family is having itching problems with their skin because the clothes are not only not getting clean but the soap is not rinsing out. In other words, we are suppose to eat this expense and move on. This is a new machine!!!!! And all it is worth is taking it to a metal place to scrap out!!!!! We will never buy another Whirlpool product again. It is really **. They don’t back their products up and do the consumer right. There are a lot of complaints online about the same identical thing I am writing about. They should reimburse the people the money that they wasted. Thank you.

In 2006, I paid $1,300 for above fridge and bought extended warranty. Within a year, I had four service calls for condensation in bins that causes freezing of lunchmeat, veggies, etc. and anything put in them. The A&E service company said to use plastic bags and then said I should keep the bin drawers open at an inch so air could flow. Next call said vacuuming underneath would solve it. Final call said again to use bags and suggested modifying the fridge by making a hole in the sidewall (which would nullify the warranty).Since I declined modifying the fridge, he contacted Whirlpool saying I declined service. I still have this problem, was going to call for service because I could really use the space the drawer provides but I have a feeling I will just be throwing money away. I was going to contact Whirlpool but Ive done that too. I feel totally ripped off on an item that should have quite a few years of service left.

Purchased in Nov. 2013, by March 2014 noticed water leak on floor, after 8 service calls in 3 months it was deemed unrepairable By Whirlpool. Got a new fridge in June 2015, no cost to us, but have had 2 service calls already for the same problem. The first leak damaged our kitchen floor, and the ceramic tile that we have is no longer made so we have had to file an insurance claim on our homeowners to pay for repairs. I would never buy any Whirlpool product again, or buy from the local company we bought the original fridge from.

I really like my new 5 burner gas double oven gas range made by Whirlpool. Except for 1 minor flaw where the backsplash panel warped at the beginning and was promptly replaced by whirlpool I have had no problems with my range, love having 5 burners and a double oven. Plus the left front burner has a much bigger burner with higher btu which helps water come to a boil way faster than any other ranger I have ever had. That is a real nice feature and I really like having 2 ovens, When cooking on an average day for my small family there is no need to heat up the big oven and the little oven is just the perfect size to bake 1 or 2 dishes. And on holidays when I am cooking for more people or many more dishes I have the capacity to cook more items.

I bought my Cabrio washer about 3.5 years ago. Little after the year, I had to replace the lid because the hinge broke. Then came the F1 code, which I noticed if you turn the machine off for a couple of minutes, it resets itself. About a week ago, it started making a grinding noise and staining the clothes with oil or grease. Transmission problems. I was told by the seller it had a 10 year warranty. I called them up and now I got to foot the bill for a technician to come to my house and tell me what I already know plus labor. Might as well buy a new one. Beware because I believe Kenmore is manufactured by the same company.

This has been the worst purchase I have ever made! Within 2 months of it going out of its one year warranty I called (Lowes) to have it repaired. Spent $300 on the first repair to get rid of the jet engine sound AND the oil splatter all over the floor then within one month from that repair it has a F code error and wont finish washing a load. It just stops. I have tried everything from unplugging it to restarting and it just wont work. Now have to wait 1 week for the repairman to come back out (hopefully that warranty of 90 days will be helpful). Do Not Buy this machine!!!

I purchased an electric double oven range on 11/20/11, model # GGE388XS00 and serial # D02584385. Something is getting in between the glass on the bottom oven door and theres no way for me to clean it out. I feel it is an issue with the seals they have around the glass oven doors.Whirlpool says its common for that to happen. They say its condensation. But it doesnt look like condensation to me. Whirlpool says theres nothing they can do about it.I had this same issue with a Whirlpool microwave oven I had. I finally ditched the microwave and bought a new one, because after a while, it starts looking really nasty. I never complained about the microwave, but after buying a new oven and it starting to do the same thing, I thought Id better complain and see what they would do about it. Theyre not doing anything about it.

Another person with problems called this a giant Whirlpool paperweight and he is so right! I received delivery of a Cabrio WTW7800XW3 washer on December 17, 2011. I had an issue (stopped in the middle of the cycle and flashed the letter “F” on the control panel) with it on January 2nd. I called and scheduled service. I had unplugged the machine and a few days later I replugged it and it started to work, so I cancelled the service call. In March, the problem started again. It just adds a little bit of water and then stops. Since then I have had repairmen out 6 times with 8 new parts installed and the washer still doesnt work. Now, the control panel won’t work. Whirlpool refuses to replace the machine. The repairman says these are the worst machines (any of the ones that are top load and have a clear top) he has ever seen and that I should buy an extended warranty. He says the bearings in the tub wear out among other things. On one of the repair visits, the serviceman found a chewed up pair of baby pajama pants. The machine makes a really loud noise like a jet engine taking off whenever it spins and the clothes are not clean. Whirlpool says that the warranty does not cover replacement of a defective machine. I have since researched the machine and have discovered that there have been problems with this line of machine for years. So, why are they still selling them? I am hoping for a class action suit. The company should stand by their products. I will never purchase a Whirlpool (or any other brand manufactured by Whirlpool) product again. I have had the machine for 4 months and it has been usable for about 2 of them.

It seems the quality issue of the LED of the washer Whirlpool Cabrio. It was broken from the screw part of the glass and the plastic/alloy and the glass. They would charge me $416 to replace the LED but I rejected and was still required to pay $85 for labor fee. I called the company and they didnt admit that was a quality issue but I just found many consumers had the same problem. If someone would like to have a lawsuit, please contact me and I will join.

I purchased a top load Whirlpool Washer and Dryer in April 2021. When it was installed I commented about how noisy it was. I was told it was because it was empty, but it will be much quieter once you put in a load of laundry. That did not make any difference. I called Whirlpool customer service and explained I had just purchased it less than a week ago and it appeared to be very noisy. I was told they could send someone out, but if they determined there was not a problem I would be charged a service call. I said the machine is not even a week old why would I be charged a service call shouldnt this be a warranty issue. Again I was told there would be a service call charge.I am completely baffled at the customer service response. This is the first and only time I called. I contacted the store where I purchased both the washer and dryer and was told it should not be that loud, this is the first time anyone has complained about the noise level and there should not be charge. Whirlpool has terrible customer service and I will NEVER purchase another Whirlpool product again because of the customer service. I have purchased numerous appliances in my lifetime and have never been treated so poorly. If I could return both the washer and dryer I would not hesitate. I would not recommend Whirlpool to anyone.

Bought the HE Whirlpool Cabrio in 2013 after having my old agitator Maytag for 19 years. After reading the other reviews I do not feel alone. An awful washer, a year after our purchase the spin cycle is so loud we have to close the laundry room door. Now it has been leaking into my basement. I called a repairman, explained my problem. He suggested to junk the washer, it will cost more to repair than buying a new washer. In addition my clothes did not clean properly, soap stains on clothes because it does not use enough water. This was about $1000 purchase that lasted less than 4 years! I am done with Whirlpool and suggest to anyone not purchase a HE washer, nothing like the old style agitator washers.

It works extremely well. My wife and I have had it for several several years and no problems with it and it cleans the dishes very well. We really like the silverware holder. The right size for a family. Recommend it to anyone.

I bought a Whirlpool water heater 5 years ago and after one year I had to replace the thermocouple every 3 months. Each time I call to complain, they would just send me a new thermocouple. I asked them several times to replace the item and they refused and just continued to send me replacement parts and refuse to honor their warranty. The water heater had some type of defect, but they still refuse to replace the item and did admit on the phone they have records of several parts that they sent.

Hello, Here is our story. We bought this refrigerator Whirlpool - 26.2 Cu. Ft. 4-Door French Door Refrigerator through a local reputable retailer. After 16 months we started to have problems with ice melting in the ice bin. We continued to have problems related to cooling/freezing within the refrigerator to the point where almost all the major parts were replaced. The good news is the dealer negotiated with Whirlpool to have all repair costs covered after the first visit. I asked about just getting us a new refrigerator and was told Whirlpool requires a part to be replaced 3 (THREE) TIMES before consideration.In summary, the refrigerator could not be fixed and was condemned in agreement with both Whirlpool and the Dealer. Here is the interesting news - since the refrigerator was out of warranty (12 months and now we are at 18 months), they are requiring we pay $600+ for the replacement. Buyer beware - either pay for the extended warranty or risk having to be inconvenienced by having your refrigerator unavailable for days or in our case, weeks!

I purchased a brand new refrigerator model # WRX735SDBM00 Ser # K51621170 on 30 June at Lowes. Paid about 1600.00. Within 5 days the ice maker was no longer functioning. I called the service department and a lengthy ordeal commenced of trying to repair. It is now 13 August 2015 and I have had over 10 visits from a technician and I still have no ice. I made a terrible mistake in not returning the appliance to the store within 30 days so now it has to go through the process which means that now I have to continue to wait until the technicians deem that this appliance is not repairable anymore before I can attempt to get a replacement.In the meantime, we have been inconvenienced, aggravated not to mention not be provided a product that works with no future date where I can get this appliance repaired. The local store management have been great to deal with and are trying but their hands are tied until the manufacturer determines they cant fix. In the meantime, the consumer is continuing to wait for the repair/replacement. No one seems to care or has there been any discussion of some compensation (not necessarily money) for the aggravation and inconvenience I have endured. Something is just not right. Suffice to say, never again will I buy a Whirlpool. HORRIBLE EXPERIENCE.

Bought this from Lowes in 2010 with the 12 yr extended warranty. Have not been able to keep it lit. Takes 4-10 days for repairman just to LOOK AT IT and then he usually has to order a new control valve, taking another 2-4 days (have had the control valve replace 3xs). This means, my husband has to get down at eye level to try to get it to light (hes 63) & if it doesnt light on the 40th try or the cramp in his hand stops him sooner, we have to heat water on the stove, carry it through the house to the bathtub, try to get the temp not too hot or too cool, then hope that our 70 yr old bodies can get down into the tub plus get back out without falling (showers are preferable). My husband bought The best hot water heater $ could buy at our local Lowes store. Because we are getting up there in years, we hoped that this would be the best answer by also getting the extended warranty. They have had numerous repairmen out to our house (6 or 7 last count)... two different men told my husband that they would only be here a couple of minutes knowing it was not going to light for them either. Time wasted. Patience gone. Still they wont replace it because if anyone can get it to light up again, no matter how long that may take, then theres no need to replace it! They have already put more money into parts, labor & repairs than it originally cost. I was told today by the ex. warranty representative that its not considered a lemon! So how do those LOWES/WHIRLPOOL people sleep at night????

We purchased our appliances including a refrigerator, stove, microwave and a dishwasher from Home Depot and chose Whirlpool because we believed in their quality. We purchased an ice maker for the refrigerator and it did not get delivered so we had to contact the store to get this resolved. Once this was resolved we installed the ice maker and began to use the products. We noticed a leak from the dish washer and checked the connections only to find out the leak was coming from inside the door. We contacted whirlpool to let them know. We were then contacted by whirlpool that they could not find a service center in our area and we needed to find one and they would reimburse us 150.00 for the service center that we find to come look at it and then we need to let whirlpool know what parts were needed and they would send them to us then we could have the service center come back and install the parts.After receiving this information I contacted whirlpool to let them know that this was unacceptable. First of all this is time and money out of my pocket and no service center is going to make two separate service calls for 150.00 dollars. So whirlpool tells me they have done all they can do in which I informed them that they have not done all they can do and they we just dumping this on me to take care of. So after arguing my point, the whirlpool employee decided to call a service center and make an appointment for Jan 09, 2020 which I agreed with and hopefully the problem will be solved. This should have been done from the very beginning instead of wasting my time only to have the whirlpool employees do their job. A customer should not have to deal with this. In the future I will using a different company for my products, not because of the product but because of the service. I have made a copy of this and will be posting my review.

Mtf18 defective refrigerator - The unit is 2 yrs old and about 6 months prior to 2014 I could not keep ice in the refrigerators ice (freezer) and the appliance compressor ran 24 hrs. a day without recycling or stop. I did not purchase an extended warranty, after all, Maytag the dependable company. The lonely Maytag repairman. Right!! The unit cost $$700. and is now an anchor. You cannot repair the compressor, only replace it...

The door can be slightly open on the model GSC25C4EYY02, and the alarm will not register. Ive come home on too many occasions to find the food no longer at a desirable temperature. Im very bummed about this refrigerator choice. The refrigerator door open alarm is useless.

Whirlpool under-counter dishwasher (model DU1345XTVB0) was purchased 14 months ago. Upper rack plastic adjustable wheel rack is broken. Will not replace. Dishwasher has probable design flaw with wheel positions causing overhanging load to put extreme stress on outer two wheels. The design was done to save money instead of having telescoping rails as most dishwashers do. Explained this. They will not even send a part. Many other Whirlpool dishwashers use these parts. Probable class action suit material.

I bought a semi automatic washing machine from Croma Store (Gurgaon) on 03/09/12 Model no A-72H* and I regret to say that the water direction changing knob (to change water flow from agitator to dryer), has broken. The machine is not even 4 months old and the water inlet is broken. How can this happen in a brand new washing machine? You claim to have durable home appliances products and your machine does not last 6 months? Can you see that the broken piece is attended to or replaced at the earliest?

Purchased brand new washer & dryer that was chosen specifically for its HE & washing capabilities as Im a single mom with 5 kids, 2 of whom have disabilities, & I need a good washer & dryer. Washer and dryer both broke several times. I paid for an extended warranty but they never resolved the issue. Called Whirlpool & they didnt care. Four years later, Im using a set I bought used that rips my clothes while the washer & dryer sit still broken. Will never buy from Whirlpool or Kettles again.

I bought the #1 rated Consumer Reports recommended Whirlpool Gold fridge 15 months ago (how convenient their warranty stops at 12 months). The control board has already gone out, lots of ruined food and ruined perception that Whirlpool made good products. I will avoid buying anything they make again. When repairman was taking it apart, I saw Made in China stickers.

In the last 6 years I have had two refrigerators each lasting three years with major repairs from day 1. I am on my 6th repair for my Whirlpool Model WRF89SDAM02 purchased in October of 2013. WHAT A PIECE OF JUNK.

Just like hundreds (maybe thousands?) of others who have had the same part failure causing the refrigerator to leak, I had it and was told by my very honest, highly reputable repairman (not the one KA recommended!) that it was a DEFECT. I bought a French Door style #4609730. First, I complained on Twitter and the Social Media folks gave me the runaround. I kept it up and then, filed a complain with the Better Biz Bureau. They sent the complaint to Whirlpool, who owns KA. They gave me the runaround too - UNTIL I TOLD THEM HOW MY LOCAL TV NEWS station was interested in my story (true, I went to them too). CORPORATIONS SHOULD NOT GET AWAY WITH DIRTY BIZ TACTICS!

Having serious health issues with both our washer and dryer. I believe there should be an urgency and more serious resolution. Our washing machine is getting clothes trapped and producing friction causing excessive and heavy smoke from the drum. Our dryer has a random bolt/screw in the drum that catches and tears clothes. Although this doesnt happen on every cycle. It happens enough that it should be investigated, repaired and reported to Health Canada. I contacted Whirlpool on September 15th 2015 with my concerns. Nothing is being done! Ridiculous. WASHER Serial: HL23299429, DRYER Serial: M24507313.

Updated on 02/13/2021: Company fails on customer service. My stove’s trim is rubbing off on my Whirlpool stove only 6 months old. No chemicals were ever used to clean the surface. This trim piece surrounds the controls and is not covered under warranty. An expensive cheaply made stove. Multiple attempts to have the piece replaced got nowhere. A letter sent to the head office was deferred back to customer service. Whirlpool has lost credibility and I will no longer buy their products.Original Review: So disappointed to find the paint finish coming off the trim on my 8 month old Whirlpool range. No harsh cleaning chemicals were used. Only mild dish soap and a microfiber towel. The trim, attached to the control panel on the front of the stove, is not actually stainless steel, but painted to look like stainless steel. Whirlpool warranty doesnt cover esthetics and refused to replace the trim, stating replacement would include the entire control panel and it is not covered under warranty. So be prepared to have your new expensive stove look old in a matter of months.

I bought a Kitchenaid dishwasher (It is owned by Whirlpool) from Trail Appliances. After 11 month the machine didnt work. It was under warranty. It took more than two months that they sent a technician to fix it. Less than one week after repair it broke again, same problem. Now we have to wait for another two weeks for technician to come. It is tough for us without dishwasher for such a long time. I learned Whirlpool is not a reliable company and I will never purchase products from this company any more.

I own a Whirlpool Cabrio. I wanted a newer technology (no agitator) washer with top loading capabilities. I ended up with a four to five-year lifespan with this washer. The bearings are busted and it leaks water from the bottom. I have followed loading instructions specifically. It will cost about $1,000 to fix so of course, I am buying another washer and a matching dryer.

I purchased my refrigerator four years ago from Lowes. From the second year ice would form in the bottom of the freezer weekly. This past week it stopped working totally. I had to call a repairman. He advised me the parts he had to replace were outdated and Whirlpool had made changes to the my refrigerator model two years ago. No recall. Just cheap parts that caused the refrigerator to not defrost. $400 later all is well and I am broke. I wrote to Whirlpool and their response was, Oh well, there was never a recall so youre SOL.

I bought a Whirlpool Cabrio washer and dryer on March 2010 from Leons under the dont pay for 18 months. It took 2 months for me to receive it. I thought it was a great washing machine. I made my last payment on July 2011.On the first week of August, the machine stopped working. The F 51 code appeared. I then looked up the code. I also looked up complaints. I called Whirlpool customer service and was told it would be $81.00 per hour for service plus parts. I asked why there are so many complaints about this machine, and after spending a good amount of money on what I believed was a good make of washing machine, I could not believe that they would expect a customer to then turn around and fork out that kind of money for repair.I was told that the one year warranty has expired, so it is my responsibility to pay. I am a widow with 2 children, working 7 days a week to pay my regular bills and now they expect me to pay for repairs on a washing machine that is only 15 months old. Thanks Whirlpool. I will be sure to tell everyone not to purchase Whirlpool products and thanks to my neighbors for letting me use their washing machine because I cant afford to fix mine.

My dishwasher control board caught fire yesterday. Noxious fumes and black smoke with popping noises moments after starting it. Was glad we had not gone to bed and glad we were home when it happened. Would not shut off and the door was hot to touch. Had to turn off switch on wall.

I purchased a Whirlpool Cabrio set 3 years ago based on their brand reputation and consumer reports. It has been a terrible experience since the moment the warranty expired. First, about 1 month after warranty expired, I had to replace the main electrical board. Then about 3 weeks ago, the drain pump failed. I purchased the $110 pump and installed it myself. Now this week, the spin cycle sounded like a jet engine. I took it apart to find that the bearings were shot on the drive shaft. I figured, well it is just a wear item, understandable right? So I went to order parts and got told that I have to order the whole outer tub for $250 with shipping! For some bearings! I called Whirlpool directly and was given no explanation other than Call some parts distributors. They may be able to help you get the bearing separate, but we dont do that and there is nothing that we can do. Amazing. I equate that to having a faulty brake on my car and being told that I have to replace the whole axle!Fortunately, the washer never really did a great job. It was loud and tore clothes up, so the decision to part ways was not too difficult. I have the list of brands they make and will be sure to never buy another. Im selling this one for parts. Im sure there are others out there that will need a pump and control board soon!

This is a defect due to the removal of the dispenser heater being removed. The insulation is inadequate behind the ice/water dispenser (@ 3 feet from the bottom of the door.) Replaced the line, thawed it out multiple times, added extra line under the fridge in the coils to try and warm up the water in the line between the 90 degree elbow connector and the dispenser... no luck. Since all the manufacturers models are being assembled in Mexico, using the same designs, other models are have the same issue. GE is backing theirs with a replacement freezer door. Well see if Whirlpool backs theirs. This whirlpool Gold is @ 3 years old and the issue started around a year ago.

I have a Whirlpool Washer Duet 4.3 cu.ft. On 24/3/2011. It has lasted only 5 months. Now, the spinner makes a loud noise. On 29/9/2011, Whirlpool sent a service man out and he replaced the bearings. But the washer is no longer the same and it is still loud. I will not buy Whirlpool again.

I have a Whirlpool cabrio washer (Model: wtw6300 Serial Number: CT3573525) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. At the beginning, I didnt care because I had warranty with BrandsMart. I had to call at least four times. But now, I bought the automatic control and it didnt work. For two days, I was trying to balance this machine but it is impossible since the beginning.I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool. Two of the gas burners of my Whirlpool kitchen, after two years of use, are no longer working. I will definitely contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

We got a brand new bottom freezer french door Whirlpool refrigerator in our brand new apartment. Since we moved in last week the temperature control in the refrigerator box has failed three times. The freezer stays cold but the coils are frosted solid and no cooling gets up to the refrigerator box. We turned on moisture control but that didnt help. The users manual is completely useless and in fact doesnt even match the control panel. The numbers for temperature settings on the instructions dont match the numbers on the panel.We had to turn off and thaw out the unit completely three times already and this is just the first week! Last night the building maintenance guys came in and sprayed the back panel of the freezer with warm water. He said he talked to the GE tech, who suggested we also increase the freezer temperature settings to 4 and the refrigerator to 44. But this morning the temperature rose again. It sure sounds to me like the daily defrost cycle isnt running at all and nobody wants to consider that possibility. Thaw the unit several times a week is completely ridiculous. Our food has experienced so many temperature excursions who knows whether its any good now. I cant wait to get my first taste of salmonella. This is what you get when you combine junk with poor service.

I purchased a Whirlpool top load washer that has been ruining my wasted items. My terry cloth towels all have pulls in them, knit polo shirts have pulls and holes, sheets and other items of clothing get caught and stuck under the agitator which then take a great deal of muscle power and struggle to release them. I have had the agitator replaced 3 times to no avail! Whirlpool is not willing to admit that I have a defective machine and will be sending another service repairman to try and fix the problem - this time, no charge to me after many tries and frustration. Customer service is not good unless you are lucky enough to get a supervisor who is willing to listen. We shall see what this next service call brings. I do not have high hopes and will keep you informed.

Ive owned whirlpool appliances for forty years or more, and have been consistently pleased with them. My first washer and dryer lasted eighteen years while raising a family. Brand X lasted eight years with at least four repairs before we dumped the set. We moved and sold one set with the house, but my newest washer and dryer set is eleven years, and works fine. Ive had at least four ranges. We sold two of them with the houses, but theyve all been fine, just bought a snazzy new Whirlpool range as an upgrade. Im on my fourth Whirlpool refrigerator, but again we sold one with the house and we upgraded one perfectly good Whirlpool refrigerator to a bigger side by side with icemaker. Third whirlpool dishwasher. Weve moved a lot, leaving behind appliances and buying new ones. Sure, Whirlpool appliances break down, but they sell zillions of them, and you never hear about the zillions that never break down.

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

I purchased a Whirlpool washer in 2005. After the extended warranty expired, our washer broke. The Whirlpool manufacturer did not have parts in stock. It’s on backorder, so what does that tell you? So we have had to wait for over a month for the repair shop to receive parts from Whirlpool’s manufacturer. Service is very slow and the quality of product is very poor. After five weeks and no repair parts, we are going to have to purchase a new washer since we do not have our washing machine repaired yet. I promise to never purchase a Whirlpool product again.

we bought a hotwater heater and it gets scalding hot set on the low setting, we had the gas valve replaced by a@e paid for by whirlpool. It still gets above 125 degrees,set on vacation with me using it all during the day.I have contacted them several times, they told me to let the hotwater run about 10 minutes everyday, or just turn the heater off and let it cool off. I bought a water heater to use not light the pilot everytime I need hot water.

Whirlpool Duet Steam Front Loading Washer Model #WFW9750WW01 - The washer is only 5 years old and sounds like the space shuttle landing while in the spin cycle. Cost to repair parts only will be $896.87. The bearings among other parts are shot. I will NEVER own another Whirlpool appliance under any circumstance. Angry is putting it lightly!!!

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

Our Neptune washing machine is 15 yrs. old. Minimal problems, which I could fix myself. The door gasket needs constant attention to prevent mold. It is a front loader. I have replaced the gasket once. The belt transiently slips.

Bought Whirlpool Dishwasher MDf760SADMZ including protection plan in November 2015. Product did not last even four years --top and bottom racks began falling apart-- and drain motor went out causing near flood in my kitchen. Disappointed consumer.

We have put hundreds of dollars in service calls and parts on these items. I bought them because they were supposed to be good choices. NO way! I have replaced motherboard in washer, belt and sensor in dryer, the washer has had mold in it since week one. Ive tried to clean it but just keep coming back. All my clothes smell like mold and I already have lung problems! Cant afford to buy new right now. But last month my dryer started making terrible banging noise and so repairman says I need another part! I bought the part more money! Just to have it quit again! Now the barrel split! I dont think I should have to pay the money I did for this set and surely shouldnt of had to replace so many things that went wrong or put up with the sewer smell from the washer!

I bought what I thought was a great washing machine. It is a top loading Cabrio from Whirlpool. The machine leaves white residue on all my dark clothing. It is a disaster. I am following washing instructions exactly, using HE detergent, loading the right amount, I even tried using PODS. I tried different temperature water, different cycles of washing and spinning and the same thing happens. I had an old Maytag that broke that cleaned beautifully. This thing is a piece of garbage and I would love to send it back if they would let me. DO NOT BUY IT. I AM BEGGING YOU, YOU WILL BE VERY UPSET.

I purchased a Whirlpool oven/range from Lowes in September 2016. It was working ok until the convection fan stopped working. I purchased the extended warranty for 3 years but the oven stopped working in December (3 months past the extended warranty). When I contacted Whirlpool to complain about the horrible product they have been selling to people, all they could do was suggest a repair company that charges $99 to come out and diagnose the problem. DO NOT BUY any whirlpool appliances. The name brand used to signify quality but the appliances they sell now will not last. BTW I may have used the convection function maybe once per month over the past 3 years ... So its not like I over used the oven.

Purchased Whirlpool gas hot water heater from LOWES on 9/25/2016. After the installation, tried to light the pilot light for 90 minutes. Followed the recommended instructions, I could not get it to light. Called LOWES they told me to call Whirlpool. I did so, and told them I will return the heater to LOWES the next day. Whirlpool customer service very bad. Returned the heater to LOWES the next morning, went to a local plumbing shop and purchased a Rheem heater. After installation it lit very first attempt. Now three weeks later I get a letter in mail from collection agency that LOWES turned me in for stopping payment on the check I wrote them. After reading the many negative reviews and they disregard for my and my familys safety, nobody should purchase a Whirlpool gas heater from LOWES.

Our dishes always come out completely clean and without spotting. I dont like having to get down into the machine and clean out the filter/trap, so I pre-rinse everything that goes into the machine, so that might help. Regardless, this machine does an excellent job. This is the Whirlpool Gold Series bought in 2013. It has numerous settings, such as delay, varying cycles, air dry, heat dry, etc. All the features work as expected, but like most owners probably do, I leave it set on the same settings all the time. It does what I want and does it very quietly. This is a standard, under-counter, full-sized machine. The outside of the dishwasher is stainless and the inside has a plastic lining. The controls are at the top of the front door, so that leaves the front completely clean-looking. Love it.

I have a front load Whirlpool Washer and it has leaked within 6 months of having it. The rubber piece was replaced and it still leaked. Whirlpool wont take responsibility for its product. I have to put towels down around the washer every time I use it because it leaks. I purchased this because it is more economical to use a front load but not when water is leaking from the washer.

I have had no trouble with this ref. There is absolutely nothing bad I can say about it. Once or twice something has fallen behind the drawers/ranks in the freezer.

I have had nothing but Whirlpool for 40+ years, I am on my 2nd washer and 2nd dryer! They do the job I need, they are very reliable. If I had any downside it would be they don’t hold a queen size comforter.

We purchased this washer on 2008-04-27. It ran okay until a few months ago when it began making strange intermittent noises. This is now happening more and more often. I reviewed a lot of websites and see that this is a common occurrence for Whirlpool Cabrio washers, and Whirlpool will not stand behind it and make it right. Im going to write them a letter mirroring what Im saying here, and remind them that other appliances in my house are coming due for replacements or upgrades. Whirlpool and its affiliates will not be part of those upgrades going forward. I have no patience or tolerance for expensive **, which is what they put out here. I will have to purchase a replacement washer since this seems to have two major areas of failure, both extremely expensive to repair. I might check out Roper and see what they have--its apparently very well rated by the folks that work on these things.

We got a DEAL for this nightmare for nearly $700 back in 2014. Nothing but problems. Constantly finding plastic pieces at the bottom... some identifiable; others not. They are from the cheap parts within. The control board lights (all but 1 works) went just after the 1 yr mark. We are now having to replace the top Rack Adjuster (MORE CHEAP PLASTIC), as it has been barely hanging on for the last year and a half... constantly fighting it, as it would drop all the dishes if you moved it wrong.Now, the water is not draining at all... period. We clean this religiously - always rinse dishes completely, use rinse aid, never stuff dishes. Today we find a random plastic piece, which we are now trying to identify. NOTE: we dont put plastics in the dishwasher. So, today a new plastic piece and major drain problems. We are in the market and purchasing a new French Door Refrigerator and Front Load Washer. Will NOT be going with anything Whirlpool. Not much better these days, but this name has a big RED NO for us. Made it even worse when we contacted for help after that 1 yr mark. NO HELP AT ALL.

We purchased a Whirlpool refrigerator from Conns Appliances on 2/2/12. It worked fine until about 2 months ago. Then it started freezing food in the refrigerator. We called Conns, and they sent a technician to replace the thermostat. A couple of days later, it was still freezing food. So we called Conns again. They sent a second technician. He called Whirlpool tech support, and they told him to adjust the position of the thermostat sensor. A couple of more days went by, and food was still freezing. The problem had gotten even worse.I called the manager at Conns and suggested that we should consider replacement since the previous 2 technicians were unable to solve the problem. He sent a third technician. Tech #3 called Whirlpool tech support and re-adjusted the sensor. He said there wasnt a lot they could do and that if I wanted to get it replaced, I would need to call Whirlpool.I called Whirlpool Customer Service and explained everything that had happened. They told me they would need to send another technician. I asked why, since 3 technicians had already looked at it. She said there were different levels of service and they would have to send someone from their authorized service company, as if Conns is not authorized. I asked if this problem was common in this model of refrigerator. She said she could research that if I could hold, so I said ok. After being on hold for several minutes, she came back and said she couldnt find any record of this being a repetitive problem.I didnt have a thermometer, and I thought if I had more concrete evidence of the problem, then maybe they would replace the refrigerator. So I put a glass of water in the middle of the top shelf. Within 24 hours, it was frozen solid as an ice cube!Technician #4 came and called Whirlpool tech support. This time, they told him that this had been a problem ever since this model came out and they had a fix that had been on the books since day 1. So the customer service lady obviously lied to me. Technician #4 stuffed a piece of Styrofoam in the hole where the air comes from the freezer into the refrigerator and he re-adjusted the thermostat sensor. I asked if we could just replace the unit and be done with it, but he said we had to wait and see if his fix worked.I went to Ace Hardware and bought a refrigerator thermometer. Two days later, we had frozen strawberries, frozen lettuce, frozen milk, and even the meat and cheese were freezing. My thermometer said temperature was 32 degrees. I called Whirlpool back and insisted that they replace the refrigerator. They told me The unit was not authorized for replacement and they needed a 2nd opinion. I was very angry. I told them there had already been 4 opinions and a 5th wasnt necessary. I wasnt getting anywhere, so I asked for a supervisor. They transferred me to someone named Sue. Sue told me the same thing - not authorized, need a 2nd opinion. I told her that I work at The Mens Wearhouse and that if a customer spent that much money on a suit and had trouble with it, they certainly would not have to bring it back 5 times to have it re-tailored. I asked to speak to her supervisor. She said, Sir, my supervisor doesnt speak to consumers. I could not believe my ears. Where would they be without consumers? I was so mad I hung up on her.Later, I realized I had no options and called to request the 2nd opinion. I was told that the technician could authorize the unit for replacement. They also told me I couldnt get a technician for a week because their technicians were all booked up repairing their faulty products. I had no choice but to wait. I moved my thermometer to the bottom of the refrigerator to see if the temperature was the same there as on the top. The temperature there fluctuated between 28 and 34 degrees. I called Conns to tell them the story, thinking maybe they would go to bat for one of their customers. They told me this should never have happened and that the matter should be escalated to their home office and that a manager would contact me within 30 minutes. He never called.Two days after that phone call, I went to Conns to speak to the manager. I told him the whole story and told him that if Whirlpool would not replace the refrigerator, then I would have no choice but to contact Discover (my payment method for the original purchase) and dispute the charges. I pointed out that even though it should be Whirlpool paying for it, his store would take the hit if Discover reversed the charges. He called someone and told me a Conns service manager would contact me within 48 hours.More waiting. Technician #5 came. I told him he was to authorize the unit for replacement. He said he couldnt do that and that Whirlpool tells all their customers that just to get them off the phone. He re-adjusted the temperature sensor and left. I was livid. Now the problem went the other way. The temperature wouldnt go below 50 degrees. We filled an ice chest with food and ice and began living out of it. The Conns service manager called and said he would have to send a technician. This would be #6. I was very angry with the service manager and called Discover to dispute the charges. Discover opened an investigation, sent a letter to Conns (and maybe Whirlpool, Im not sure) and issued a credit to my credit card account.#6 came and re-adjusted the thermostat sensor. The next morning, he called to see how it was doing. The temperature was still around 50 degrees. He wanted to come and adjust it again. I told him to get the unit replaced! So he submitted paperwork to request a replacement. He called back and said that he felt sorry for us because he knew we had a 3-month-old baby in the house. Since the replacement had been requested, Conns wouldnt pay him to come again; but he said he would come on his own time, on his lunch break, and readjust the sensor in hopes that it would get us by while we waited for a replacement. He said it might take 3-4 days to get the replacement. I told him he could come, so this was technical visit #7. He adjusted the sensor. The next day, the temperature was still 50 degrees.I called the service manager at Conns to confirm that they had requested the replacement. He said the paperwork was submitted, that the home office would review it, make a decision, and that we should know something in a couple of days. That was on Wednesday. On Monday afternoon, I called him again. He said the paperwork wasnt submitted to home office until Saturday and that he was expecting to hear from them by end of day Tuesday. In the meantime, we were still living out of an ice chest.I had already determined that Whirlpool wasnt going to help me, and now, Conns was giving me the runaround. That afternoon, I was working on a project at work with a lady who was fairly new in our company. Turns out she used to work at the Conns home office and she knew people in high places there. She called a VP on my behalf. The next morning, I got a call from the VP telling me that I could get a replacement. I dont think I would have gotten my replacement if I hadnt bumped into the lady who used to work at Conns.I called Conns store, and they said a credit had been issued and I could come to the store and pick out whatever I wanted up to the amount of the credit. I knew I didnt want another Whirlpool. The selection was very limited, but I found a Frigidaire that I thought might work. Then they told me I would have to pay extra for an ice maker, even though I had bought the ice maker for the Whirlpool that was being replaced. I argued with the manager until finally he agreed to give me the ice maker, delivery, and installation.Yesterday, Conns called to tell me they were coming in the afternoon to install the refrigerator. They had the audacity to ask me what was the matter with the unit they were replacing! They did come and replace the unit. But wait...Thats not all! This morning, the ice maker had not made any ice, even after running all night long. Conns sent a technician today, and he said all of the parts were not installed and it was preventing proper water flow. He is coming back on Tuesday to install the missing parts. So we still arent done. I dont know if Im more angry with Whirlpool or with Conns. Whirlpool did not honor their warranty and Conns got stuck with it. But then Conns provided poor service too. I got stuck in the middle, and it still isnt fully resolved.