I went from an HE front loader to an HE top loader (Whirlpool Cabrio WTW7000DW0) due to the risk of mildew with the front loader. Im not the only one doing laundry and if someone else does it, it always seems that they shut the door when empty, contributing to moisture and mold that needed to be cleaned out of the gaskets. I am so unhappy with my top loader HE washer. When I stop the machine and look, I always see my laundry half covered with dingy water, sometimes part of it still dry at the top and it is disgusting. I frequently have to rewash loads due to detergent getting trapped in folds or pockets created that hold on to dirt and lint, even being careful with the detergent amount. I run the washer now every time with settings of deep water, extra rinse, heavy load and presoak with instructions, with settings taped to the top for others.At almost 1 1/2 hours each load, we just cant keep up. The laundry still forms pockets and sheets form a giant tent over the entire load that has to be unraveled at the end of the cycle and wound so tight it had no chance of rinsing. I had to get a repair person out because it got out of balance and he had a small hand-held computer to enter a code to rebalance it. When we discussed the issues I was having, he was ready for everything I was doing wrong. He told me I can not wash blankets or large items (I thought I was buying large capacity with such an enormous drum). He told me they have caught people adding water with a bucket during cycles and that the washer software can tell them if people are trying to work around the system which voids the warranty.Apparently, this is a common complaint he blames on the government wanting high efficiency so they make the numbers look good, sacrificing the ability of the washer to perform at what a consumer expects. I have never seen the water in my drum higher than a couple inches and the drum is HUGE, but never used to capacity. He told me his wife demanded they get a commercial washer because she was so angry about how poorly it cleaned. I feel so scammed and I wish I could have my old agitator back. $100 for the repair call, $150 for the code to be put in and Im on warning that they will see if I try to add water, run out of balance or dont comply with any reason they can void the warranty by just checking the data the washer is collecting on us.

I purchased a Gas Stove from Home Depot on 11/23 and it was delivered on December 3rd. My God, Im having a dinner party tonight and the stove doesnt heat up past 170.. Unbelievable!! Need a replacement gas range. Tried to chat and call Whirlpool unsuccessfully. I am very one disappointed customer right now!

Purchased a Whirlpool refrigerator the last week of January 2014 with promised delivery date of February 6, 2015. Received call Feb. 2 that the earliest they could deliver would be February 13th. Received call Feb. 3 that the earliest they could deliver would be February 19, almost 2 months after purchase of refrigerator. Sears, where we purchased the refrigerator, told me that they have been dealing with this for 10 years with Whirlpool. Why would Sears sell products to their customers with this kind of delivery problem? They only communicate with Whirlpool via email, so there is no resolution with a person to get issue taken care of. We will never buy a Whirlpool product again & will never buy anything from Sears again.

I love my glass top stove and glad I purchased it, so much easier to clean, I think they should all be made self-clean on any stove, I did not notice that some dont come with it and some dont. Remember not to start cleaning the top of the stove until you can touch it with your hand.

Manufacturer refuses to acknowledge quality issues. This is not exclusive for the washer or dryer, IT IS BOTH! P.S. I owned & operated a Whirlpool Cabrio washer & dryer for 6+ years before up-sizing & loved them! I was grossly misled by the retailer to believe the new Cabrio washer & dryer were the same as the previous model of Cabrio. They are not. Their performance is subpar. Not what I would expect from top of the line. Washer does not spin out as dry as the previous model. It will not show error codes on display so I can deal with the issue at hand-it just shuts down. Dryer sensors do not work properly. It will not dry, or overdries to the point of shrinking clothing beyond use.This $2800 purchase is continuing to cost me money. I have never been more upset with a purchase than this. I have to babysit these machines. There is a bolt in the back wall of the dryer drum. Hence my destroyed brand new hand crocheted afghan. Oh and did I tell you that their licensed repair man told me that I should not be laundering bedding in my machines at home? Apparently there are no home use machines on the market that are able to wash bedding. Sheets. Pillowcases. All of it needs to go to a commercial laundromat. Ha! Makes a person question who we let in our home. If you would like a positive - its huge. But wont spin out a small load effectively.I have recommended and led to sale of dozens of the previous Cabrio model. I will no longer be standing behind this model or company after the poor customer service. Their answers are scripted. Its like speaking to a robot. No one is accountable anymore. I could understand if I did not know how HE machines worked or even the Cabrio model, but I loved my previous HE CABRIO FOR 6+ years!! Excuse me while I go vomit.

My model - GB9FHDXWD06 - is one of only a very few that fits our space. However, it has failed three times in 5 years: 1) A faulty defrost drain tube that was replaced under warranty, 2) A jammed vent flap that caused the freezer to fail, and 3) a burned-out control panel (an expensive repair). It is also annoyingly noisy and middling at energy efficiency. The coils are in a very narrow space below the refrigerator, which makes them a bear to clean. And, the plastic front plate that must be removed for cleaning breaks far too easily.On the good side, it is a bottom freezer model (which is far better for convenience), the space-wasting ice maker was very easy to remove, the glass shelves, removable baskets, and drawers are easy to clean, and the auto-defrost works very well (after the recall update, number one, above). Temperature uniformity is good and the freezer maintains below 0° very well. Overall, it is a good looking appliance with mediocre efficiency and poor reliability. Not recommended.

Weve owned a Whirlpool Gold Series Dishwasher for about seven years. There has not been a year that has passed that we have not had to place a service call with a local service provider. (Each service call costs $85.85.) The upper tray has come off the tracks more than 10 times. The drainage mechanism broke the first time we used the dishwasher. The fuse box (which is amazingly a self-contained, enclosed, black box) has blown twice, has to be completely replaced, and costs over $180. The second time it broke, I ordered, paid for, and had delivered the replacement part only to find out that the broken part suddenly started working again. (I guess Ill have the $180 part for the next time it breaks.) To suggest that this product is junk is an understatement. It will be replaced very shortly.

Absolutely terrible product. Have had nothing but problems with it since I got it. After 4 months the pilot started going out every couple of days. Would have to vacuum the filter just to get it to light. They eventually sent me a screen to wrap around the bottom, that would only extend the interval to maybe a week instead of going out every few days. Now tonight it wont even relight! So tomorrow Im buying another heater and throwing this piece of junk out, a waste of $750.00 for two years of headaches. Dont, trust me. Dont buy this garbage of a water heater. And like others I bought it a Lowes, done with both of these stores!

I bought a Whirlpool refrigerator in 2007 from a recommendation from my repairman. He told me that most refrigerators last about five years. I cant believe after five years I will have to buy another refrigerator. I know someone that has a refrigerator that is 50 years old. Cant any refrigerator makers make any appliances that last? With all the technology we have nowadays, it seems like you could. You just want the public to spend more money on repairs or a appliances. Hope you buy the product you sell! Looking forward for a reply.

After 16 months the Whirlpool refrigerator Model number: #WRT311SZDW00 goes out. While trying to use extended warranty Whirlpool states it will be 4 to 6 week before a technician can come out. YES- Weeks not days. Now Whirlpool states they are unable to find a technician in my area and in order to get it fixed I will need to hire the tech and seek reimbursement from them for the repair. However prior to the repair they will need to approve the repair. In the mean time I am renting a refrigerator at my cost. They lost a customer for life!!! Question- What is the purpose of the warranty? Model number: #WRT311SZDW00

Whirlpool refrigerator WRT1LTZW00 - Bought refrigerator, works ok but makes noises that will wake you up in any room of the house. Had Whirlpool products for over 40 years. Why would someone make something that noises. Service came, said they all like that with new gas, cant do anything. Find hard to believe this was consumer tested. 6 weeks old, cant sleep with noise. Has anyone had same problem?

Our dishwasher stopped working after 13 months. We are a family of 2 and use it once a week. We called Whirlpool and were told since it is past 12 months, they would do nothing but give us the name of a repairman in the area. We called our own repairman and $120 later, the sensor that had malfunctioned was replaced. Quite costly on a $450 dishwasher. Now, after 15 months, the handle on the lower broiler portion of my Range has come off and the screws will not hold because the plastic around them deteriorated. I just called customer service once again, knowing what I would be told and YES was told So sorry, nothing we can do. A new handle will be $45 plus shipping. We bought the refrigerator at that same time and every day, I wait for this appliance to have issues. In summary, Whirlpool/Maytag appliances are obviously made to be disposable after 12 months. They do not stand behind their products and I would not recommend them to anyone.

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.

Purchased a Jenn-Air single wall oven model JJW2427WS after seeing it displayed in an appliance store. Oven was installed as directed. Upon viewing the panel, I discovered that it does not light up. You cannot read the function or numbers, never mind start and cancel without a flashlight. I have been a Jenn-Air customer for over 20 years. This is the first time I have been disappointed. Also, has this model been discontinued or recalled?I wrote to the CEO of Whirlpool and explained my problem. I was told that this is not a functional problem, but perhaps a design dissatisfaction. I cannot believe that there are other consumers who are not having difficulty using their appliance without additional lighting in their kitchens.

A-10 error on display ultimately means needs a new pump. The washer (model WFC7500VW 2) is 3 months, 9 days old and is now unusable. I cannot get any service (under 1-year manufacturers warranty) because the sticker inside the door with the model and serial # is missing (i.e., it was sold to me by Homedepot.com without a serial # on the door label, sticker is intact and is brand new and apparently was printed without a serial #).I made multiple calls to Whirlpool in Benton Harbor, Michigan and finally spoke with Courtney (who states she was a supervisor) pretty much said all they will do is to reprint a label from the factory and I should have it in 7-10 business days. They refuse to stand behind their product and authorize timely repair of their product they sold to my without a serial # on the door tag from the factory. I have to wait to schedule factory warranty repair until I get the new label (probably 3 weeks plus without a usable washer). Courtney refused to contact me via email for any of her contact information or to supply verification of conversation or promise of a new factory label. Also, she refused to try to authorize any type of manufacturers warranty to fix the brand new unusable washer!

We purchased a Whirlpool refrigerator to match the other appliances in our kitchen. The unit was purchased in June of 2012. Two and a half years later, it quit making ice and would not maintain proper cooling temps. Not to mention the noise coming from the compressor. So we had a certified tech come out and he said that it was the sealed refrigeration system. He stated that he had seen this issue a lot with whirlpool refrigerators. He said that what they don’t tell you is that it is covered for 3 years but good luck with getting any satisfaction. The cost to fix it you ask? $700.00. Might as well just buy a new one. Took a shot in the dark and called Whirlpool customer service. Gave the girl my information and model number. I got the “Sorry, but your model number is not covered by the sealed refrigeration warranty.” Then I got the ole, “Is there anything else today?” Well, she got the wrong man on the phone this day. I asked her to give me a model number that is covered by the warranty and I will purchase that one. You could have heard a pin drop. I don’t guess she’s been asked that before. She starts to ramble and said, “Well, there are just so many, I could not possibly tell you. Some are and some aren’t.” (Remember that statement) You mean she can tell me that mine was not covered, but could not tell me which models were covered. Huh??? Long story short. I argued with her for an hour on the phone and she finally breaks down and admits that Whirlpool does not warranty the sealed systems on their refrigerators any longer because they are considered value brands. What are value brands you ask? I asked the same thing. I was informed that a value brand is of lower cost to draw people to buy the product. Remember in the movie Back to the Future when Doc Brown said he sold a nuclear weapon to the Libyans at a good price but it was just filled with pinball machine parts? Well, there you go. I get the supervisor on the phone and she has the I’m going to be strict with this customer voice. She basically blames me in the fact that I failed to purchase the extended warranty. You’re right, my fault. How dare I have the nerve to think that a one thousand dollar value Whirlpool refrigerator would last no further than two and a half years? My bad on that one lady. The end result; I was told that I could purchase a new Whirlpool refrigerator and be sure to get the extended warranty. Yeah, why don’t go practice falling down Whirlpool, I’ll be there in a minute. (That was sarcasm by the way).

Apparently, Whirlpool selling all their rejected faulty washing machine in the market. The trick they are playing is the machine being sold with one year parts-labor warranty; They wont replace these machines with a new one because they know that these machine will never work, consumer will buy the faulty machine, obviously it wont work so consumer will call for service. The service guy will say that “oh! Machine needs a part and then the customer service will say “the part is being ordered”, “wait”, then the service guy will come with the part and after wasting some time he will say “Oh! The machine needs another part, and again customer service will tell the consumer that “you keep calling us”. One year will be gone! Bottom line – faulty machine is sold, Whirlpool made profit, buyer is robbed. I am one unfortunate customer who purchased Whirlpool Washing Machine which never worked as it is a faulty machine which should not go to the market at all; Whirlpool made money on my hard-earned dollars and I been robbed.

Updated on 04/15/2019: Called customer care about my ice maker which have went out for the second time less than two years and the 1st replacement have only been 9 months from today. Unfortunately they tell me it’s out of the one year warranty process and they can’t help me. Well look like the 2nd replacement should have been under warranty still. Their products are a piece of crap and they know it and don’t care because theyre making money off of the consumers. Be aware and advise you to stay away from Whirlpool appliances. They don’t stand behind their brand. There’s no way anyone should have to be making repairs on a new 2000 and sum refrigerator. My old one is 18 yrs old and still working fine no problems, better than this piece of crap. Warning to consumers. Don’t waste your time and especially your money. Didn’t want to give no stars but you have to give at least 1.Original Review: Purchased refrigerator In July of 2017 and had to have ice maker replaced less than a year of having it. Now again ice maker not working again and only been about 9 months from the last replacement. I think there should be a Lemon law on these products. These refrigerator are not cheap and if I buy something new and spend a good amount of money for, I don’t want any headache and worries. That’s the reason for getting a new one.

I have never posted a negative product review but must do so now. The refrigerator is 1 1/2 years old at most and has been well taken care of. I noticed today that the finish at either side of the bottom of each refrigerator door handle has a problem. I couldnt tell if the finish was pitting or is just discolored. I called customer service and expected that they would help, especially since we have an extended warranty. Representative number one told me that the extended warranty only covers problems that affect the function of the product. I spoke to her supervisor and then her supervisor. I got plenty of apologies but no support. I offered to send pictures, but they were not even interested in checking out the problem.After speaking to them, I took the handle off and I see now that the handle cut into some sort of film that exists on the metal. (I am not talking about the protective plastic coating that is on the the refrigerator at delivery.) The film is lifting off the surface and creating discoloration. If Whirlpool was at all concerned, I think this issue could be fixed with some sort of gasket to keep the metal handle from cutting into the surface. Im hoping the problem is static, but hard to say what will happen. If they had been interested in trying to understand the cause of the problem, it would have been easier to accept the limitations of the warranty. It would have demonstrated an interest in avoiding this problem for other consumers in the future. My last Whirlpool product. Period. Good luck if you decide to do business with them.

We purchased a stainless steel refrigerator thinking Whirlpool stood behind their product. Within days, the shelving on the door and meat bins and vegetable bins literally started chipping away and cracking. I have over a thousand dollars product held together by glue and duct tape so I can use my refrigerator. Neither Lowes or Whirlpool wanted to back their product. But it seemed they wanted to make a sale only on replacement parts... Now today I have learned my ice maker drum has chipped away... Thankful no one swallowed the plastic. We will never buy Whirlpool or recommend to our friends again.

My new Whirlpool Stove, has two grill like tops, heavy duty and awesome looking. It has a special burner to keep food warm, a stainless steel front and bottom drawer for broiler storage. Broiler is also on top in oven, broiler flame.

We have a Whirlpool Cabrio mod. WTW5600 XW2, ser. C12830447 he... H2O.. low wash system. Less than two years old. It does not get clothes or towels clean. I put 2 jackets in on bulky items and part of one of the jackets was still dry. They were two small childrens jackets. My husband and I wash as long as possible and on hot wash (which is not hot!). Should not take 70+ minutes to try & get normal clothes clean!Now the softener is draining into the wash with the detergent. Another service call. Learned you can only fill the softened bin half full or less. WHAT??? Our extended warranty is up soon and not sure what to do. We would like to get rid of this pile of junk but cant afford another washer bill. Also wouldnt want anyone else to get stuck with it. Its a shame a company cant put out #1 good product and #2 stand behind it. Bring all of the company production back to the USA or put out a better product and stop worshiping the almighty dollar. Im done with Whirlpool (which was the product to buy), but stuck with this washer for now until we are sure that the brand we buy performs as it should. What happened to the PRIDE in & RESPONSIBILITY of making a good product and standing by what youve made. As my hubby has said, if you have to buy an extended warranty, whats wrong with your product! Again worshiping the almighty dollar or is it you just dont care about the people who buy your product or its quality. Maybe both.P.S. Have contact you before without a response.

Im very satisfied with the looks and performance of my Whirlpool dishwasher, it is quiet enough that I put it on to wash before going to bed. It is that quiet. Im not happy about the way it was installed, but that is no fault of the dishwasher or Whirlpool, it works great even though it sits kind of crooked in the cabinet. The dishes are always sparkling clean and dry when it is done washing.

Both the washer and dryer make terrible screeching noise. The dryer only dries on time drying. The store I bought them from have been here over 7 times too fix them. They still are not fixed. Just a terrible experience with this set from day one, load one.

My gas range doesnt work all that well. Sometimes the flame catches and lights, sometimes it doesnt. Oven seems to be less than steady in cooking. It is ok, but I wouldnt buy again.

Switched to bottom freezer and love the size. We all use and enjoy the filtered water. Whirlpool has proven to be a manufacturer I will always consider when making major appliance purchases for performance, service, and dependability.

We purchased the Whirlpool Cabrio washing machine around January 2006, and from the start weve had nothing but problems with this appliance. Within the first year, water was leaking under the washer which was coming from a crack in the plastic housing of the water pump. I replaced the pump myself to save on labor. No big deal. The very next year, I started getting the F51 code and there was no way for me to get around calling a service company to have it repaired. $350 and one circuit board later, it was repaired. It remained working without fail until recently when it began giving the same F51 code. Let me guess, another $350 for better repair? I have to assume that the new circuit board that was installed wasnt any better than the original one that was replaced. I wouldnt put another $1 into this hunk of junk and Whirlpool should be ashamed to have this product on the market. I will never buy another Whirlpool product.

I purchased a #Whirlpool; 4.3 cu. ft. Mini Refrigerator Stainless Steel BC-127B from @Target. There was a delay putting it into service (6 mos), so the Target store warranty was expired. The unit remained in its factory shipped packaging until put in service, so nothing out of the ordinary there. After barely two weeks of use, the compressor died. I followed all instructions (including waiting 8-10 weeks) from Whirlpool, but still have not received a refund or been given any information beyond we escalated it to our warranty team but havent heard back yet. The unit was a poorly made piece of junk in other respects as well. There are dozens of complaints about precisely this - defective units - on any site. Do not be fooled by the dishonest way that #Targets website lists reviews. Dig deeper.

We just recently remodelled our kitchen and decided to buy a Whirlpool Range. Big mistake. First off, the range was advertised as a built in but it ended up looking like a slide in. We were disappointed but decided it was ok as long as the range performed fine. However, within 6 months of buying it, the oven fan broke and the oven became unusable. I used it only 2 - 3 times before it gave up. Extremely disappointed. Our old oven was sturdier and lasted many years and was in a very good condition when we gave it away. Extremely disappointed since we paid a lot for it.

Whirlpool Cabrio Washer - A total waste of money. My clothes are never clean. The low water system is rubbish. It doesnt work! Check out my pictures below. That is the result of a 63 minutes wash cycle. Dont buy this piece of crap.

The average life of a refrigerator is 11 years. We purchased a Whirlpool convertible refrigerator (Model EL7JWKLMS02, Serial # EWR1339731) on 6/12/04 from the Lowes here in Visalia, CA. The first delivered was DOA and Lowes delivered another. That should have been a warning sign. We have had several problems with the product, as early as 2006. All repairs went through Sierra Appliance & Franks Appliances.We are now in the market of another refrigerator to replace this one. We have had to have freon added now for the third time. Sierra Appliance was unable to find any leak, but each time, the freon was depleted. In addition to the health hazard of having freon leaking into the house, we have had the distinct displeasure of having to deal with food waste, etc. Because of the ongoing problems with this product, we are now facing the reality of purchasing another refrigerator to replace this Whirlpool product.Due to this, I feel it is difficult to consider another Whirlpool product and will question any product to ensure that it is not Whirlpool-related. If there is anything that Whirlpool or Lowes can do at this point, it would be appreciated. Thank you for reviewing this note of dissatisfaction. It appears that we will be shopping for a new refrigerator this weekend unless we hear from Whirlpool. In any event, I would like this recorded as a complaint from a former customer.

I bought a Whirlpool water heater in March, 2008. Last time (not sure if its last year or 2 years ago), I had an issue of the water not heating. They have someone came in to replace a part. Recently a humming sound (scary one) keeps on coming on from time to time. It took me some days to find where the sound is coming from, and there it is, my fairly new whirlpool water heater.They said it has something to do with the orifice. Since I am not a handyman, they recommended a service guy to come in, and I have to pay. I wonder how much more I have to spend on this heater? Yes Im saving gas consumption, but it will be spent for service anyway, and I have the added bonus of frustration. It is not worthy having it. I spent $1,400 for the heater and labor.

I purchased a new park model house with Whirlpool appliances. The fridge door is crooked in 2 directions. It is only adjustable in 1 directions. Top to bottom. After 5 months of trying to deal with whirlpool and being told my warranty is void because of adjusting the door according to their manual. They also tell me that warranty will not cover factory flaws which the crooked door obviously is. Whirlpool will never darken my door again except on the way out. Whirlpool sucks!

I bought a top of the line Whirlpool dryer that cost me over $1,000. Havent had it for a month and it requires a service call. Have to wait two weeks for service! Totally unacceptable. The dryer is JUNK and now I am stuck with it. Horrible company. Bought from Home Depot.

In less than 4 years the top lid broke at a poorly designed hinge point (+$200). Cabrio washer mercilessly tangles/twists clothes; HE does not totally rinse all detergent from clothing necessitating extra rinse (so much for efficiency); now at 4 year point bearing has gone and machine sounds like a freight train (+$250). Do not recommend this item if this what to look forward to. Called Whirlpool initially about tangling/twisting problem and just got lip service about arranging clothes. Duh, did that already.

Bought a Whirlpool fridge (WRF560SFHZ) 3.5 years old not cheap! Suddenly one day, the freezer drawer cannot close properly. Since it broke down on a long weekend, I have to wait 3 days in order to contact Whirlpool customer services. And then wait for another 4 days for them to send a technician. The technician advised it is a screw on the rail fall down and he fixed it and charged as 115CAD repairing fee (for a loose screw). He said it is a product defect from Whirlpool and that we should call Whirlpool to ask for a refund.Of course after a long wait from the hotline, Whirlpool refused to refund, saying that, It is not within warranty period and it is perfectly normal that you paid for 17** CAD fridge and can only used for 3,5 years and that things happens (screw can get loose). The service rep. even said, You bought it, it is your property now... And they dont care you have to throw away food in the freezer since the door cannot be closed. And of course they refuse to admit that the product has an inherent defect... Will never buy this brand ever again!

We purchased a Whirlpool Gold Series dishwasher from Lowes approximately 2 years ago. Serial P32105232. We noticed a dark stain coming up in the hardwood floor. It was a water leak from the dishwasher appears to be from seal when water cycle leaves unit. This has caused over 70k damage to our home. Ruined entire hardwood floor kitchen cabinets warped so all need replaced. Our insurance company has made a disaster after owning home 10 years. Custom cabinets that match the laundry room as well. No to mention. The jackhammer used to bust up 800 sq foot of flooring and the concrete dust in our entire home. Please advise recourse.

I purchased a 40-gal Whirlpool water heater model 40t91-403 last week and paid a plumber to have it installed. The old one (GE 40 gal) worked fine except for a leak. The new one used all of the old connections except the 2-inch in and out pipes. Same connections, hot, cold and gas. At first I got about a quart of hot water and then all cold. Whirlpool changed the valve and cold water pipe (inside the tank) and still the same. They are trying to tell me that the tank is fine - I have a plumbing problem. Two plumbers have told me different, but still they insist. Yes, I am upset. The old GE, even with a leak, performed better!

Purchased this 27 cubic ft French door bottom freezer fridge (WRF757SDEM01) in Sep 2016. Approximately 8 months after, fridge stopped cooling. Called Whirlpool for service diagnosis since fridge was still under warranty. Service tech stated coils were freezing over due to part malfunction and part needed to be replaced and ordered. He provided me with a temporary fix by defrosting all the ice from the coils since the part would take approximately two weeks to come in. I spent an entire day of annual leave from my place of employment for this service call!!! New part was replaced and fridge was cooling like it was supposed to.Here again six months after the part replacement, my fridge was doing the same thing again; NOT COOLING my food AND there was this awful noise coming from the area in which the part was replaced. That drove me CRAZY to the point I would turn it off in short increments to maintain my sanity. I called whirlpool AGAIN, and this time, my fridge is NOW out of warranty, BUT, the replacement part of five months prior should still be in warranty. My fridge failed the day after Thanksgiving and five days after the fact, the service tech will be at my house again.Worst part of this is I took an entire day off work expecting the service tech to come between 8-12 as told to me by the whirlpool customer service rep and guess what? The company called at 1000 and said they only do appointments in my area in the evenings. I was furious; again another day of employment missed at the hands of Whirlpool. I am not confident that the same part that was replaced in May is defective and I may be going through spouts of an inoperable fridge again and again. Whirlpool really needs to take a hard look at recalling these fridges OR providing quality appliances for the money that we pay. I had GE appliances in my old house and NEVER had issues with the refrigerator. My new builder choose whirlpool and made the wrong choice! I just want a refrigerator that will work operate for the $2100.00 that I paid. I will NEVER recommend whirlpool appliances to anyone... Never!!!

I purchased a washer and dryer set, the Cabrio Platinum Series WTW8500BRO, about 3 years ago. I had a UL code come up a year ago and the machine was serviced and all was back to normal. Then only 9 months later it started acting up again. This time it sounds like an airplane taking off and there is a black spatter leaking from underneath, also the lid lock stopped engaging. I started to look up the error code for the lid lock and while reviewing that issue it was an easy fix, however, the noise and black spatter issue led me to tons of horrible reviews about this product. It is a bearing/tub/shaft issue that is going to cost me $500 to fix. First off I did not pay cash for this set, I rented it for 3 years and paid twice what it’s worth, around $4,000. Stupid on my part but I couldn’t afford it the other way. Weekly payments were easier. Now I am scared to fix this product because of all the reviews I’ve seen from other consumers. I haven’t had the other issues like dirty clothes, not enough water, high cycle times because they all start with a high number but after it configured the load the time shrinks, but this major issue about the bearings, they say I have to replace the entire tub assembly which is half the cost of the unit. So stupid and I cannot believe Whirlpool is getting away with this crap. Please please please inform me about any lawsuits. I will gladly participate in that. They should be held accountable for such a worthless piece of junk. Like I said I am now afraid to fix this machine because from what I’m reading, more than likely it will only last a short time.

I bought a Whirlpool washing machine on 16 Feb 2011. I started having problems with it in June. It was making very loud noises when it was agitating and the clothes were still wet after the spin cycle. I called Nebraska Furniture Mart where I purchased it and they said that after 30 days, I had to call the manufacturer. I called Whirlpool and they sent A&E out to fix it. The technician that came out spent an hour trying to figure out what was wrong with it. When he was gone, I was left with two inches of water on my washroom floor and I had to pull the washer and dryer out myself to wipe it up. He ordered a part that came the next week and a different technician came out to put it in. After looking at the washer, the second technician said that the first technician diagnosed it wrong and he ordered a new transmission for it. About a week later, the transmission arrived at my house and a third technician came to install it. The washer worked for a few days and started acting up again and leaking water. I once again called Whirlpool and they sent yet another technician out. I told Whirlpool that I had lost faith in A&E so they sent All Appliances out. The technician from All Appliances said that it needed a transmission and he would have to order it in. A few days later, he came back to install it. It worked for a few loads. The leaking had stopped but now, it does not spin out the clothes. To make matters worse, it now releases the Downy at the wrong time and I now have blue spots all over my clothes. I have made repeated calls to Whirlpool and talked to two different managers. I asked the first manager for her direct number so I wouldnt have to go through the whole explanation again if I needed to call back. But she gave me her number without her 4-digit extension so, there was no way of finding her again. When I talked to the second manager (by this time, I have lost my patience), I told him my whole story and I told him that Whirlpool has spent $1,000.00 between parts and technician service on a $460.00 machine and it still doesnt work. It is a lemon and I deserve a voucher for the full price to purchase something different.After one and a half hours on the phone, Lukas informed me that the only thing he could do was to send yet another technician to my home. I have lost all faith in Whirlpool and I believe that they do not stand behind their product. They only push you until the warranty has expired! I will never buy another Whirlpool appliance again!

Purchased in January of 2014: Brand new Whirlpool WOS51EC7AS01 model oven - interior bottom metal has buckled causing the enamel to crack and break off from oven bottom. I registered all my new appliances immediately for warranty. When this happened after the fourth or fifth time baking in the oven, I called Whirlpool to get a service person to look at it. First person Whirlpool scheduled to come out refused to even come out, without looking at my oven. He said he knew we did something wrong? They immediately set up a second service person, after two weeks waiting for an answer; I had to call him (twice). He said that his report and pictures sent into Whirlpool shows normal use and there is nothing wrong with our oven? So, Whirlpool will do nothing to repair the oven? We just spent almost $4,000.00 on all new Whirlpool appliances, and this is how we get treated? WOW! Never again will I ever purchase a Whirlpool product. The enamel is gone in spots from our oven floor. How long do they think that will last with no protective coating on the oven? Terrible customer service.

Whirlpool Gold model WRS526SIAHOO - We purchased this refrigerator 10/2013 with all the matching appliances when we remodeled the kitchen. We moved our 1997 GE refrigerator into the garage. Now the computer board has gone out in the Whirlpool and we are back to using the 97 GE. The technician told me that he sees a lot of these boards going bad.

Have to keep coins collecting in pump and ruins pump or starts leaking. I feel there is another way it could be solved. I spent enough for this washer. Now I fix that. Now it leaks on discharge hose. Hard to stop it. Like old washer worked lot better all round. Never had that trouble. 4yrs old 1,200.00 plus cost sending somebody out to fix it. Crazy! This happen more than one time with this machine. Thank you.

This microwave had been the best I have used for several reasons. One is the modern design that goes with our kitchen. Two: it heats the food very quietly and produced an even temperature through out the food. Three; The inside of the microwave is easy to clean out.

What can I say. Pretty much a generic refrigerator that is manufactured and sold under various brand names. Nothing special. Keeps food cold. Ice maker takes too much freezer space but thats typical. Interior LED lights failed after a few months. Flicker sometimes. Out other times. Internet research finds this to be a common problem. Zero quality in Whirlpool appliances. I bought four Whirlpool kitchen appliances and ALL have had problems. The only way to own them is with a 5 year extended warranty.

I hadnt had the machine. In no time, I started noticing brown rust looking spots on my whites and light colored clothing. I got to looking and had rusted out all around the bleach dispenser, entire area on the entire top. I was told to replace it. This would be about $200. Ridiculous!

Bought a new side-by-side in 7/2020 from Lowes in Keller, Texas. Salesman won me over with the buy American pitch claiming if the need ever arises for parts I would be far better off than with LG which orders their parts from South Korea. I bit, and bought, and now regret. The refrigerator dispenses water randomly and I must keep a glass under the dispenser all the time and empty it when it gets full. Under warranty they say! Well here it is September and after being on hold for an hour each time (6 times as of today) I attempt to get help they tell me that the part W11293378 is not available and will not be made until after this month? BEWARE this brand. This is a poorly ran company and buyers would be better served to look elsewhere.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

I purchased the original Whirlpool water heater from Lowes in April 2008 for $372, and an installation charge of $443, grand total - $815. In February 2012 the tank leaked profusely, enough to ruin a section of hardwood floor in the room behind the garage where it was installed. Whirlpool provided me with return authorization, and Lowes provided me with a replacement water heater. So far so good. Since the original installation was done through Lowes, the replacement had to be as well, according to Whirlpool, but now they charged $500 with tax to install the replacement water heater! Grand total now is $1315. Fast forward to May, 2014 and the replacement water heater, just barely 2 years old, shuts off with a code of Bad gas control valve/thermostat. I call Whirlpool and an extremely rude 20-something staffer tells me the unit is out of warranty by one month! The replacement unit has no warranty at all - nada - only the original one does... Is this unbelievable or what?! BUT, they would be glad to send me the replacement of the defective part for $200 PLUS overnight shipping charges, and I would be responsible for all labor charges to install it. Had I opted for this my original $372 water heater would have wound up costing me in the neighborhood of $1800!! I told her in no uncertain terms what she could do with the repair part, and now I am going to go shopping for a water heater that will last me more than 2-4 years, and you can bet it wont be a Whirlpool, and it wont come from Lowes.

This washer is 5 years old and the top is rusting out on the inner rim. I have city water that has been tested and found to be totally safe to use and drink. Neighbors using the same water and owning different brand washers have no rust problems. Does anyone else have the same problem with their Cabrio washer?

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

High end Whirlpool dual front loader washing machine model number WFW94HEXW2 died after 5+ years of less than moderate use. Used no more than once a week. Paid for a top end model. Had 2 mechanics look at it. Mechanically it is fine. The CCU is not working correctly and wont allow it to start. We replaced it, but to no avail. It is barely out of warranty at 5+ years old. Called Whirlpool and they said they would do nothing. Asked for a manager and she was rude to add insult to injury. Cant get to the serial number because the door is locked shut as part of the shutdown problem. Cant find original receipt so including a picture of the credit card purchase. Trying to contact retailer but so far have not heard back from them.

I purchased my new washing machine in September 2011. When I removed the clothes from the washer after the first wash, I noticed that there was soap on several of the items. I ran them through another rinse and spin cycle, and there was still soap on several items. In an effort to avoid this problem, I no longer use the soap dispenser tray, and use the bulky cycle to get more water in the tub. Like most of the others, the clothes are tangled and stretched from one side of the tub to the other. Also, it takes 1 hour and 36 minutes to run a complete cycle. The manager of Sears tells me, that because of government regulations, that in a few years, you will not be able to buy any other type of washer. I purchased this machine, because it was highly recommended by Consumers Report magazine. I filed a complaint with them eight days ago, but have not had a response.

Whirlpool Cabrio drain problem - I never had a washing machine that lets so much through to the drain pump. I replaced pump three times already. First of all, if you put anything with buttons in this machine, you can kiss it goodbye. This machine destroys clothes then lets buttons and coins and whatever through to destroy the fins on the discharge pump. When is the BBB going to do something about this consumer ripoff?

This is our second Whirlpool refrigerator that has the same defrost water drainage problem. I was told this newer model had updated technology, not so, actually it is worse. My older refrigerator went about 8 years before I started noticing water on the floor and this newer model is 4 years old and it started having water overflow at 3 1/2 years. Then in April we replaced the water filter and the ice-maker stopped working. My freezer also stinks like stale water (my reason for replacing the old refrigerator plus the water on the floor). I followed a YouTube video for defrosting the drainpipe, it was very tedious, labor intensive, and time consuming and worked for 3 weeks. This is very upsetting. After spending $2500 to have such problems and my expensive $150 4-year extended warranty expired just weeks before the ice-maker went out. This is obviously a design problem that Whirlpool refuses to address since my other model was a year 2000 model and my 2013 has the exact same problem. VERY POOR customer care in addressing these design failures of both the defrost drainage (just make a larger drain port!!!) and the ice-maker.

Refrigerator caught fire - I own a 2003 Whirlpool Gold side-by-side refrigerator that I bought new from Lowes in 2003. On Friday, July 13, 2012, I woke up to the smell of burning wires. I called 911 and they sent out a fire engine. While waiting for the firemen to arrive, my neighbor came to help me determine where the smell was coming from. Within seconds, we heard loud clicks and a huge cloud of gray smoke came out from behind the refrigerator. The firemen arrived, entered the house, unplugged the refrigerator and told me that the smoke and smell was coming from behind the fridge.

It gets the job done. Its no power washer, but the dishes get pretty clean and dry nicely. I have no idea how dirty the dishes can be and still get cleaned, since Im weird and pre-wash my dishes. Its stainless steel and black, and has quite a few wash and dry settings, including an option for heated or unheated dry. The utensil rack is attached to the door of the washer and cant be moved. Two levels, and pretty easy to do dish tetris with. No offense to most standard dishwashers – I need a washer about 3 times the normal size due to a passion for cooking. Its slick and matches my ultra-modern, borderline-Swedish interior.

We remodeled our kitchen and my wife liked Whirlpool, I didnt, but I went with her since she got a good deal with Lowes. We bought a microwave, dishwasher, stove, and fridge. I cant wait till all of it craps out! Going back to Sears! In less than a year I have replaced the stove and stove, the fridge sucks. The fridge already had a defect with a water leak, damaged my hardwood floors!!!! Still waiting on Whirlpool for my floors. The dishwasher never cleans, it always stinks. The stove does not self clean, the handles dont stay tight, shall I go on!

We bought a new Whirlpool side by side, model # WRS325FNAM00 in March 2014. In less than 48 hours, the freezer box was condensing and water was leaking on the bottom edge. The condensation got worse and worse. Five service calls later, Whirlpool replaced the freezer door--which took six weeks because it had to be manufactured.After the door was installed--no change. Whirlpool replaced the entire refrigerator in June. Guess what? The new one is doing exactly the same thing in exactly the same place. So far it has not gotten worse. Well see, we have only had it a week. But already the service rep has been out to the house and added the silicone gunk to the box in case there is a tiny air leak. Why would a brand new refrigerator have an air leak in the freezer box?

Whirlpool WRF992FIFM00 - Purchased new April 2017. Its October now. Service has been called 7 times so far. Ice maker has not worked since day 1. Fridge leaked all over the interior around the third month. Compressor went out in 5th month. Compressor replaced 2x so far. Every component piece was replaced on 5th month. Still no ice. As I write this compressor getting ready to go out yet again. Paid almost $3000 for this piece of crap. On first name basis with technician. He tells me that his guys work on this particular refrigerator CONSTANTLY. So far I have lost over $1700 in food and wages (leaving work to meet technician). Currently battling Whirlpool. My next step will be legal action if they do not refund or replace this stainless piece of garbage.

This is the second time since I have bought my Whirlpool top loading washing machine, which was January 1, 2011. During a power outage, I was washing clothes and my machine lid would not unlock after our power came back on. I called the warranty service and they made arrangement for a repair man to come out to repair it, but the appointment was in two days. Meanwhile, I had clothes in the machine I needed and was afraid they would become molded and no good. So my husband opened the lid and I removed the clothes. When the repair man came, he was not going to repair the machine because we opened the lid. He was very rude, but after doing some talking he repaired the lid. Now, once again we had a power outage while I was washing clothes and the lid is locked on the washing machine and will not open. This happened Friday, March 16, 2012; my appointment for the repairman to come is Tuesday, March 20, 2012. Meanwhile, my clothes are sitting in the machine wet because we were told not to try to open the lid and wait for the repair service to come. I am very concerned my clothes will be molded and I will be unable to use them. I would never buy another washing machine like this one. Model number is WTW4800X, Standard/Ordinaire VOXr8ENA(3B). Date of purchase: January1, 2011.

I had a Whirlpool oven for 14 years. It worked great and the control board burned up during the cleaning cycle. I purchased a new whirlpool oven that did not have an exposed bottom heating element. It takes way too long to preheat and if during baking, you need to change the temperature, it starts preheating again and the displayed temperature is lower than the original temperature that was set at the beginning; and it takes too long for the oven to reach the new temperature. This appears to be the result of the bottom heating element being hidden. Heating and maintaining a consistent temperature is far more important than being able to clean the bottom of the oven especially when this is a self-cleaning oven.Updated on October 20, 2015: This is an update on my last review. I was cooking a cake at 350 degrees and when the designated time was up, I opened the door to check for doneness. The cake needed to cook a little longer, so I closed the door and the temperature immediately went to 300 degrees and started preheating again which of course caused the oven to get too hot for the cake I was baking. Who is designing these ovens??? Certainly not a person that cooks on a day-to-day basis. I will never buy a Whirlpool oven again.

On April 17th mid morning I noticed that the freezer side was not keeping items Frozen. Everything was melting period. I then opened up the refrigerator side all the items are not as cool as they should be. I then proceeded to do a Google search to see what I should check for in regards to the freezer and the refrigerator side not keeping cool. I then proceeded to pull the refrigerator out to inspect the back of the refrigerator. When I did that I noticed there was a hot mark on my wall, as well as a huge it burn mark on my floor. I then unplug to the refrigerator do the huge fire hazard and I touched my floor and it was very hot to the touch.I called my stepfather who is a firefighter and had him come over right away. He said we needed to take the refrigerator outside right away because the compressor had overheated and that is why it started to burn my floor. He then went to the fire station and got a heat sensor check machine, and we checked my wall and floor and we had to make sure that it was cooling down so it did not start my floor boards on fire so then we had to put a fan on it to cool it down. I then went and purchased a new refrigerator, due to this one was no longer able to be used or repaired. The refrigerator was only four years and 5 months old. For a $1,300 refrigerator it should last longer than 4 years.I called Whirlpool the following day or two days later and regards to this issue. The only thing they could tell me is that they were sorry, this refrigerator almost started my home on fire and we have six children a family of 8. It ruined my floor and part of my wall in my kitchen and we have lost a few hundred dollars and groceries. This is ridiculous and not the first time, I read a few others having this issue, Whirlpool said they have never received any complaints in regards to the refrigerator burning the floor and does not see it as a fire hazard at all.

I am a working single man. I needed a used washer. I shopped the new washers but they were a lotta money. I seen many of them were without agitators. Well heck... who am I to judge the progress in technology?? So, going around to the used appliance store I run across this Whirlpool Cabrio. OK, Whirlpool meant quality my entire life. So, I bought it. MASSIVE MISTAKE!!! This POS is no washing machine. I dont know what it is, but it is NO washing machine! It is a machine that runs a very few gallons of water into a load of clothes and makes them wet, and that is about it!!All I know is the federal government is dropping the ball on this situation BIG TIME!! To allow a company to foist off on consumers such a PILE OF JUNK!! The pile of crap is PURE junk as far as simply doing its job... washing clothes!! It is a DISGRACE of an American product, and I will NEVER buy anything made by Whirlpool the rest of my life!!I took the device off the lid that tells it when the lid is closed, and just stuck it in its receptacle in the body... so I could raise the lid while it is running and watch this POS in action and try and figure out what the hell is going on. First big problem is it NEEDS an agitator!! Obviously Whirlpool had not figured out how to make the clothes circulate without one. Second is the water level (no matter what cycle setting) is obscenely LOW!! The clothes do not circulate AT ALL, and about 1/3 of them do not even get below water level for the entire cycle!! What I am forced to do is use a water hose and run a lot more water off into the tub just to get the clothes in the damn water!! And ever at that, the clothes still do not circulate AT ALL!! They just rub up against each other!! And I have to use twice as much soap than called for!!

Most of my appliances are Whirlpool - dishwasher, refrigerator, clothed dryer and the Cabrio washer. The washer before this one, I had it for over 10 years and replaced it because of rust (thats another problem with Whirlpool - rust). Now the Cabrio hasnt got all kinds of problems - UL, F1 and jumping. The serviceman asked me for $450 for repair; it included a set of springs for the drum, a new electronic board and a 30-day warranty on parts and labor. Im better off buying a new one (I cant afford at this moment). My wife is scared of the darn thing and refuse to use it so now I have the job of washing and standing guard to make sure the washer doesnt leave the garage. Thank you, Whirlpool - and my refrigerator works fine all rusted.

I purchased the Whirlpool Cabrio (wtw6600sw2) about five years ago. Last year, the motherboard had to be replaced. This year, it started to have load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $75 to have someone look at it, and to fix it will cost almost $400, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. I called Whirlpool and my model does not have a recall, but models with same problems have been recalled. I will never buy a Whirlpool again!!!

We purchased 6 six appliances for our home just over one year ago. The initial problem with the washing machine literally took ten home visit to resolve with the final solution being total replacement. Far too many days away from work. The laundry appliances have a loud beeping noise that goes off with the slightest contact, annoying and designed to be eliminated or muted. Today we discovered that the water filter in the fridge is single sourced at over $50 with shipping, which seems usurious at best. Will look elsewhere for the next house/purchase and NEVER buy from this company, including their other brands...Kitchenaid, Maytag, etc.

Every time I wash clothes, I get a terrible odor that permeates my home. Ive put in afresh to rid the problem. Ive had a technician take it apart to clean the filter & hose. Nothing helps!! My clothes come out smelling like the sewer. I called the company, and the person I talked to had no real solutions either. Im MAD! What are you planning to do about my stinking problem? Im washing clothes right now & have to have all doors open & fans on high!!!

This washer is going back. It simply will not spin the water out of the clothes. It says it gets clothes drier than a conventional washer, but I have not found that to be true. I have to use the drain/spin cycle over and over and still the clothes are wet. I had the repair crew out and they were able to get it to spin out a very small load consisting of two sheets and two towels. Other than that, it does not spin out water. It is also very difficult to load if you attempt to leave the center open as they recommend. The cycles are very long. Not being able to look inside without pausing it and waiting for it to unlock is also a huge hassle. I am getting one with a glass top so I can see what is going on. If you leave it open for too long, it cancels the cycle and drains all the water, and you have to start over which is another problem because all your detergent just got drained out before the load gets going. It uses so little water on most of the cycles that the clothes get totally tangled up with one another. I think you should be able to choose the water level manually. I am all for saving water but if I want more water from time to time, this does not allow you to do that. I DO NOT RECOMMEND!

Refrigerator stopped cooling... Paid $200 to have it diagnosed... Cost more than a new refrigerator to get fixed...$14,000. Refrigerator was 7 years old, energy star. How can it be energy efficient if it was made to last only seven years? How much energy is wasted making new ones to replace the broken ones, that cost too much to fix. Energy star. What a scam.

Standard looking dishwasher. Quiet and efficient. Best value for the money. Highly recommend. Chose this brand over more expensive options and made a great decision!!! I dont have a single complaint.

I purchased a Whirlpool Cabrio washer model #wtw8200yw in August 2012. I just purchased a new washer today (Jan 2018) to replace it! We have had to replace the lid lock twice, then the cycle knob would only work on the normal cycle. Last week it started to sound like it was going to take off! Had a repairman come and the bearings went out in it, will cost almost $500 to fix! Not spending another dime on this junk! I purchased a new washer today (not a Whirlpool either!)

I join the many who have posted about the Whirlpool Cabrio Washer cracked lid issue. Our Whirlpool Cabrio WTW7800XW2 glass-lid washer suffered the same (inevitable) fate – cracked plastic on the lid at the hinge stress points, after the washer was beyond warranty. Same story - runaround/no help from Whirlpool. Finally bit the bullet and shelled out the $200 for a new lid. HOWEVER, I didnt want to just replace it and have the same issue down the road. I removed the spring-loaded units that support the hinges, hoping to just remove the springs to release the pressure. I found that the springs are integral to holding all the components together in this unit. These are extremely heavy-duty extension springs, so I took them to my hardware store (TrueValue) and found springs the exact same length, but with a smaller wire diameter and thus requiring less force to extend. I replaced the original springs with these (Century Spring Corp. - #C-143 - 9/16”x3”x.054”). The lid operates perfectly, and now there is very little resistance at the hinge stress point. The only difference is there is no longer a “damping” effect when lowering the lid - it must be lowered manually rather than being allowed to fall on its own. That’s a small correction in habit, but will ensure that the replacement lid lasts for the life of the washer.

I have a 1 year old Whirlpool washing machine (Model: WFW94HEXSW Serial:C04151969). The grease from the drum is found to be the cause of clothes being ruined during the wash cycle. I waited over 3 months for a replacement. The drum arrived broken. I ordered again, and it was then said to be on back order. The water shut off developed a slow leak, causing the water to fill, and flow out the front door, causing carpet damage. We have been forced to throw away good clothes, and pay to have our clothes washed, at a not so local laundromat. We feel it would be more than reasonable to have our washer replaced, and professionally installed immediately.

I paid big bucks for a five burner, convection stove. I had a pot of boiling water on and the steam melted the plastic cover over the controls. Whirlpool said I had to buy the whole electronic panel. Close to $175.00!

We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2016. What a nightmare. Just a few months after having it, we kept getting an E3 error message that would not go away. After 2 weeks of waiting before a tech could come out there replaced a door mechanism said it would be fine. After the next wash same thing, same problem. Could not even open the door to get my laundry out. Again they could not get a tech out for at least 2 weeks so Im stuck with the cost of getting my laundry done elsewhere. This time it was the motherboard. Had to wait a week for that to be shipped out. This was all completed in June 2016. We are now the beginning of September and same problem. Again we are told at least 1-2 weeks to get a tech out. Seriously Whirlpool, we are your customer. I have a family and we need to wash our clothes. We spent $1200 on this machine only to have to take our laundry to a public laundry mat because your machine keeps breaking down. They will not replace the machine even though this is the 3rd time with the same problem. The customer service is horrible. They are not willing to help in any way to get this fixed much sooner for her or give us a new machine. This one is obviously a lemon! I will never purchase any Whirlpool appliance again and I suggest based on some of the reviews on here no one does. Next appliance I buy I will do more research for sure.

1.0 out of 5. This is the absolute worst washer that I have ever owned. Do NOT fall for the top loader hype. The clothes do not get clean. Anything black constantly comes out with a white residue and whites are dingy. Ive tried numerous detergents and used as little as a tablespoon and still get the same results. The company just insists that its too much detergent or that I need to run the clean cycle after every 4-5 loads. The service guy that came out said this is the number 1 complaint with these washers and Ive talked to plenty of friends that experience the same issue. The company would have you think this is the first time they have heard of it.I have spent hours on the phone with whirlpool and Home Depot over the past year and neither accept responsibility or offer any solution other than some free cleaning tablets from Whirlpool and Home Depot offered $200 off the purchase of another washer. This was when the washer was only 6 months old. The only way around this is to rewash the clothes and a second cycle and to wash all loads on bulk load with an extra rinse. Yep. Great water savings there! Save yourself the headache and dont buy a top loader of any brand and I would never buy another appliance of any kind from Whirlpool and Home Depot because of their poor customer service in handling this common issue.

I just purchased a new stove after using my old one for 15 years with the same great quality. Its the brand I will purchase when I have my retirement home built next year and leave my new one in the home for my son so he wont have to buy one for 15/20 years.

My old dishwasher washed much better than this one. For one thing, I do not think having the silverware basket in the door is a hindrance more than anything. For one thing, the silverware does not always get clean. Even some of the dishes do not get clean. I think the engineering of the dishwasher is poor. When you pull the bottom rack out to put more dirty dishes in, it gets caught on the silverware that are in the silverware basket in the door. Makes it very difficult to get the bottom rack out or in. I have no gripe on the size of the dishwasher. I would just like it to wash the dishes and silverware clean. The appearance of the dishwasher is good but that doesnt clean the dishes. I am more than satisfied with the appearance of it. I do like the buttons being at the top of the dishwasher so that a person cannot bump them when it is running. I just think the design of it could have been much better. My other dishwasher had the silverware basket inside on the bottom rack and I really liked that and if I ever buy another dishwasher, I would make sure that it is inside the dishwasher. I dont believe that Whirlpool is the company it used to be. I have an oven that has been nothing but a problem for me and it is a self-cleaning oven but I cant even use the self-cleaning feature because it blows something in it and it doesnt get hot and clean it. Have had it fixed twice and the company that sold it to us will not even talk to us about it. Im not sure that I would buy another Whirlpool appliance of any kind again.

I purchased the Whirlpool Quiet Partner II dishwasher, Model DU1055XTVQ0, Serial # FY3762359. The racks are cheaply made and rusting! Almost all of the tips on the racks are rusting, causing them to corrode and break off completely! This dishwasher is well under 5 years old. Not sure what we paid for this machine but the racks should not be doing this after this short length of time. They shouldnt be doing this after any length of time.I called Whirlpools customer support center today and was told there is nothing they could do. The support agent asked if I had hard water, if so, that could be causing the problem (I dont have hard water). The agent stated that they do not cover rusting racks nor would they replace them, now I see why. They are expensive to replace. As of now, I will not be buying another Whirlpool appliance - ever! They just lost a dissatisfied customer due to their very poor quality and customer service.

I purchased a condo last year with all appliances included. My Whirlpool refrigerator model is GI6SDRXXY00, a fairly new refrigerator. I noticed orange and moldy spots on ices when dispensing them. I changed the filter, thought maybe it is the filter causing the issue. But after inserting the new filter and emptying the entire ice tray, I still get bad ice! I open the compartment, and surprisingly, found out that the spiral rod inside the ice dispenser was rusted! This is horrible and unacceptable! This is not a user fault but a manufacturing defect. The parts that are in direct contact with what customer consumes should be robust and safe. I contacted customer service, and they gave me a technician phone number which turned out to be a third party which only cares about money. They said they will inspect the refrigerator and will charge me $134.00. I will not use this refrigerator anymore and will replace it soon. AND I will never purchase any more Whirlpool products. This manufacturer is crossed out from my list of vendors who I do business with.

We have a new home with a Whirlpool gold refrigerator that has been fixed twice in 3 years for not cooling adequately (over 45 degrees), a dishwasher that the mother board has gone out twice with 3 different service calls (repairman recommended trashing and buying a new one), microwave that is rusted out on inside door below glass, and washer with horrid smell if you dont wash with bleach weekly and dryer whose sensor doesnt sense anymore after 2 service calls!!! I cannot believe the poor customer service and lack of responsibility the company has taken on these not inexpensive products!! Like others on this post they will not acknowledge problems and tell me I should have bought extended warranty. I am so angry - there should be some sort of law that allows recourse for such bad behavior!

Read reviews on the same washer (Cabrio Whirlpool) that I had purchased in January 2017. I have the same problem everyone else has with it, not cleaning the clothes. It was such a disappointment. Had a Whirlpool front in loader for 15 years. Loved it! But the washing machines without the agitator on it is a laugh. What person thought up that design. What a joke on the poor unknowing people that purchased one. Im also upset at G&H Appliances for not standing by their products they sell. Found out that Lowes has a 30 day satisfaction guarantee on what they sell. Not buying from Lowes and buying a washer without on agitator on it. Was two big mistakes I made. I wanted to help out a small local business, but wont be doing that again. They sure are not worried about me.

I purchased a Whirlpool 4.3-cu ft top load washer with a stain steel basket, in March 2020. Machine is able accommodate comforters, automatic water level adjust to loads. Washer has an extra rinse and spin feature. Low noise when operating. I would purchase washer again.

We have a 2 1/2 yr. old Whirlpool gas stove. We have had the mechanic here several times as it would not ignite. We also have had the control panel repaired twice as it melted. It is melted again but they will do nothing. I tried to clean the oven with their AquaLift technology and had to re-do it four times and still have residue which appears to be permanent. We are very frustrated with it. We have used Whirlpool appliances for over 40 yrs. but will not buy another. Model#WFG710HOASO, Serial#R21712236.

In May of 2010, my husband and I purchased a Cabrio washing machine. By the fall of 2010, I had put in a call to Whirlpool due to the washing machine chewing holes into clothing and not cleaning the clothes. Some of the clothes would come out of the washing machine with dry spots on them. Whirlpool sent out two different servicemen and even though one of them replaced the agitator we have still had problems with it. One of the servicemen even tried to tell me it wasnt the machine but it was my detergent (I use HE Purex dye free). I was told by a service rep at Whirlpool that there was nothing more they could do and I would just have to deal with it. I understand that products go faulty but with good customer service these issues could be resolved. Whirlpool obviously has little regard for their customers. I have contacted the Better Business Bureau. Hopefully they can get results.

This washing machine (Whirlpool Cabrio) is the worst piece of machinery I have ever purchased. We have had to make numerous expensive repairs and now its broken again. Rather than pay $400.00 to repair it yet again we have decided to buy a new one. Definitely not a Whirlpool.

After the second year, everything stated to fail. The pump, the main control, even the mounting straps all failed. We are very glad we got the extended warranty. Parts alone have exceeded $400.00. Right now we are dealing with the loads not drying.

Very sad appliance company. I purchased a Standard Pacific Home in June 30, 2015 and moved in Aug 1, 2015. Use my Whirlpool Dishwasher for the first time back in Oct and it was not working properly. Whirlpool scheduled an appointment with Accord Appliance in Temecula Ca and the company was a no show. Called Whirlpool back and Rep Emma was very rude and had to call supervisor to schedule another appointment to repair dishwasher. Whirlpool have sad employees and sad appliance.

My refrigerator is now 5 years old. I have a stainless steel fridge. I didnt even have my fridge for 2 months and the one door started to rust. Whirlpool did fix that but now my fridge isnt staying cold. My extended warranty was just up 5 months ago. Figured some of the repairmen that we have called wont touch our fridge because they say the model that we have breaks a lot and that Whirlpool discontinued making this model. I am disgusted with this fridge.

I bought a Cabrio set in June 2007. Within two years, I had to have the barrings replaced ($800 job). Now, its two years later and Im getting a F50 code. The repairman put in a new part, still got the same code and left. I am out $970. I am a disabled vet/single parent and now I have to buy a new washer. Who is going to start the class action suit against Whirlpool?

I purchased the Whirlpool washer and dryer three years ago and I absolutely wish that I hadnt. After three years of use, the bearings on the tub are shot. I need to replace them but it will cost $400.00 to repair. This is the second time that this machine is for repair. I am going to dispose this machine and purchase a new model other than Whirlpool. The overall performance is poor and not as advertised. It does not use enough water and does not wash clothes well enough. At times, you can see that the water never reached parts of the garments. I am totally disappointed in its value and quality.

Horrible Customer Experience. After having my Whirlpool side by side with bottom freezer for 5 months it quit cooling (both freezer and refrig portions). This happened on a Saturday evening and Whirlpool was closed until Monday (no emergency service shown on their website for my area). Whirlpool contacted their service agent and they could not come out until Wednesday. Service tech said compressor was bad and had to order new one. Compressor arrived the next day however they could not come back until the following Monday to install. By this time I was without a refrigerator for 9 days. Techs installed new compressor and by Tuesday it quit cooling again! Tech came out the next day and said he thought the problem was the compressor and now says its the evaporator. I had to wait until the next week before they would come and install the new evap. By that time I will be without a refrig/freezer for 16 days. I contacted Whirlpool customer service and talked to several different people and all they would offer me is $50. I will never purchase a Whirlpool product again!

My daughter bought a mobile home manufactured by sunshine mobile home co. in Red Bay al. The home is only 6 mo. old. In that home there is a Whirlpool microwave oven model # WMH2175XVB-1 Serial # TRY 20 23398. After 2 months my daughter microwave stopped working, Whirlpool sent a repair man out to fix it. He didnt have the parts to repair it so he left to order some parts that he thought might be the problem. When the repairman returned two weeks later with the parts, he replaced a door switch. The oven started to work. About 4 days later it quit working again. The repairman returned for the third time, tried repairing the oven and was unable. I had to help him remove the oven so he could take it home with him so he could try to repair it. At that time I was so angry that the Whirlpool co. would send a repair man out three times to repair something that was obviously junk. When I talked to the people at Whirlpool they told me all they were authorized to do was repair it. I explained the repairman has tried three times and couldnt and that they in good faith replace the unit. The answer I received had to come from a mentally challenged person. If this is the response of Whirlpool about their product, then I want no part of them in the future.

I have had this refrigerator for over 25 years and cant ask for anything better than that. Would buy another Whirlpool refrigerator. Has original french doors at top and bottom door on freezer. However, I dont particularly like the pull out drawer that the new refrigerators have now as I get so much more room with a door. The new refrigerators have improved rubber around the doors. That is the only thing I had to replace on this refrigerator.

What a disaster! Within one year we had to repair the stove twice, the dishwasher and the fridge! Almost three years later, we are experiencing problems with two burners and with the fridge! The company does not stand behind its products. Avoid them.

I am on my second Whirlpool hot water heater within 7 years and both had a 9-year supposed warranty. Upon replacing the pop-off valve (at my expense), I paid $98 to replace the gas valve (part was issued by Whirlpool). Still having problems with pop valve and now the pilot light wont stay lit. Upon calling the number (877 817-6750) I was finally told they would replace the heater. When I stated that I did not want another faulty Whirlpool heater and that I would take the faulty heater back to place of purchase but that I wanted a local plumber to install their own heater, I was told that I had to have a thermal expansion tank or they basically would not do anything. Why would I want a third Whirlpool product? The second one is ruining my tiled basement floor as it is. So after spending over $600 for the faulty heater, now I have to spend $700 to replace it.

A couple years ago we purchased a Whirlpool Cabrio WTW8000 top-load, high-capacity, washing machine based upon good claims of the salesman at Lowes - Appliance Dept. This was not an inexpensive machine. However, this washing machine failed to live up to representations and performance is poor. However, biggest complaint is that clothes are able to get stuck between drum and the unique agitating device which results in holes and tears in material. This is a significant design flaw and were not sure why more people dont complain about this rather significant design flaw. Of course, there are other shortcomings... but destruction of clothes is a serious problem. While this machine is in excellent condition, it will be replaced with a more traditional washing machine with vertical agitator ASAP.