I was sold a gas water heater that had my water smelly like rotten eggs in less than 6 months. I bought it in January 2016 and by June the anode rod I am told was no good. The only thing Lowes could do for me was sell me 2 anode rods, one the plumber thought was bad. I also had to hire a plumber. I was eventually told I was out of luck because the area the old anode rod was in was too damaged to come out.

I have had my washer & dryer about 12 yrs. It has given me great service; however the spin mechanism on the washer stopped one month ago. It was replaced thru my home appliance warranty. I need the front loader style because Im disabled now, and cant take clothes out of washer. My previous set was Kenmore & it lasted 20 years. Looking to purchase in 2 months.

I have a lower end 4 burner model but I love it. Both power burns are in the front (I would change that) and electronic ignition. The oven temp is true and heats up quickly, I bake upwards of 700 cookies at Christmas time. Even being a lower end model it works great and I use it everyday. I think it is more energy efficient than the model that I replaced, which I replaced in order to have the electronic ignition. I would recommend this Whirlpool Range!

Bought a new Whirlpool side by side refrigerator. What a piece of crap!! I am using my time to write this review as the repairman fixes the latest problem. I dont have much hope because he asked for my assistance and is sighing and grunting over there. I had the traditional puddle of water to start. Tray underneath was cracked. Was actually fixed. Water and ice taste like crap. They said its my city water... ok whatever. No good ice and water - we will survive. The food in fridge was freezing on the low. Guy just announced he broke the new thermostat... Yes, the thermostat broke after a year. Will get it fixed, hopefully enough to hold up until I can find another new refrigerator to buy. Never a Whirlpool or any of their other companies. Time to do more homework. So glad for these forums. Ugh!!

WRF989SDAF 29 Cu. Ft.. Weve had nothing but problems from this refrigerator. Water filter stopped working after 3 months. At one year, the left corner froze over and created a big bulge and repairman said it was a recall for a part and he had to completely dismantle the left side of the refrigerator. At one year 3 months, the ice maker started leaking water and all the ice melted and ruined our hardwood floors while we were on vacation. At one year 6 months, the freezer stopped working and we had to throw out hundreds of dollars in food. Along with the freezer stopping, the ice maker stopped as well and the water dispenser starting leaking again. What a nightmare this refrigerator has been!

In 2012 we purchased a Whirlpool Nu40T61-403 water heater from Lowes that I installed due to us not being able to afford a plumber. I have since become a plumber. This morning while attempting to shower I noticed that the water was lukewarm with the shower valve turned all the way to hot. I got dressed and inspected the heater. I began to diagnose the problem. Pilot was out and Gas control valve signal light was off. Lit the pilot and it appeared to be functioning normally. My first thought was the thermopile had failed but seeing the pilot stayed lit this proved to not be the case. I was extremely relieved at that point. Turned the temperature control knob to high and the burner kicked on. At first it appeared to be functioning fine. But within about 20 seconds I began to hear detonations within the sealed combustion chamber.

We bought a Cabrio washer less than three years ago. I have never felt that it got my clothes clean. The washer recently stopped spinning and agitating. We were told by a very experienced repair technician today that the gear case and bearings in the tub need to be replaced at a cost of $700.00. Needless to say, I am very upset. I called the Whirlpool Company and after being on hold for almost 15 minutes, I was told that my washer is too old to qualify for any help with repair cost or part replacement. My household consists of two adults. We do on average three loads a week. This is an inferior appliance and after this experience I will never purchase another Whirlpool product.

Bought my 5 door refrigerator from Lowes in December 2016. Was delivered in January. Had a dent in the door so another new one was ordered that arrived in late January. From day one the dual ice makers have not made enough ice for our family. I called Lowes to have it checked out thru warranty. The repairman came out and said Its making ice. I cant fix something that is not broke. He suggest I buy a under the counter ice maker. What the heck! I pay over $3000.00 For dual ice makers and still dont have enough ice to supply my family. Cant believe Whirlpool puts out a dual ice maker in a refrigerator and it cant even supply a family of 5. The repairman said a normal family size is 3. I dont know where he came from but to me thats not normal. He was from Tutor Appliance Repair and was very rude until he realized he pissed me off then he blamed it on Whirlpool. The refrigerator is beautiful but Id rather have my old one. It made more ice than this new one does. Will I buy whirlpool again? No I wouldnt. If they cant stand behind their product and what its suppose to do then I dont need it. Bad thing I have to deal with this one for a while until I can purchase a new and better one. If you have this refrigerator dont plan on having guest or family dinners it will not hold up for ice tea. Not to mention after dinner drinks. Model # WRV986FDEM01. SeriAL # K63817128.

Do not purchase Whirlpool smart freestanding gas range model number WFG975HOHV. I purchased the range and the refrigerator around Christmas of 2018. The first time I turned the oven on to make Christmas dinner the carbon monoxide detector alarm went off. I have tried to use the oven twice after that and the same thing happened. The oven also never gets to 350. I spoke to Whirlpool who said to unplug the oven. They stated a technician would be sent with a carbon monoxide detector and to conduct repairs. The technician came and could not get the oven to 350 and the carbon monoxide detector alarmed. He stated he has to order parts and return to complete repairs.This is a brand new oven that I could not use because the carbon monoxide alarmed and the oven was not heating to 350 because it keeps restarting every few minutes. So here I am not able to use the oven for over a month and waiting for parts for a brand new range. Do not waste your money on Whirlpool products. Also the customer service has no empathy knowing their products are defective.

We have recently retired and moved into a smaller home. The kitchen needed to be furnished with all of the normal appliances. We bought two Whirlpool products, a refrigerator and trash compactor. Since we are living on a fixed budget, I was hoping that the furnishings that were bought would last as long as our past appliances did. However, our brand new refrigerator after two and a half years needed to have a new light installed. We called Whirlpool and set up for a repair. The repair was $290.00. We paid the repair man working for Whirlpool, then called Whirlpool and asked if there was anything they could do to help with the cost. They suggested that we buy a protection plan. Both of the refrigerators we have owned during the past fifty years lasted twenty plus years. This one only went two and a half before having to be serviced.Whirlpools answer to my request of helping out with this $290 service call was Sorry, you should have bought a service plan. I wish I would have gone with either of the same brands that we had in the past. Those being, Sears and Sub-Zero. I would suggest that those of you who are contemplating buying a kitchen appliance, choose a company that has a product that will go more than two and a half years without having to be serviced. Neither of the other refrigerators that we had ever had to be serviced. They stayed with the houses we sold.

My Whirlpool dishwasher is used 2-3 times per week. The interior has more than adequate space for a full load of pots, plates and utensils. A normal cycle is used and the washer is essentially very quiet. Dishes/glassware always come out spotless and squeaky clean.

The washer and dryer, Cabrio, machines are not even 4 years old and Ive had to repair four different things! Literally just replaced idler pulley today, went to put a load in wash and F1 code appeared. Control panel, 350.00 for whirlpool or a technician to repair! 285.00 for part. I called Whirlpool and was not offered any apology. Never again will I purchase Whirlpool crap appliances!

I have been using Whirlpool brand of appliances for over 40 years. They have always served me well and very dependable. Im a semi retired HVAC contractor and also installed Whirlpool heating and air conditioning systems in peoples home, also very satisfied with the results.

I thought this was a nice high end washer and dryer set but it does not clean even wet mud. The mud just smears onto other parts of the clothes. My dog had an accident on her blanket so I threw only her blanket in on deep water setting, this is a large capacity washer and not a large blanket, the accident was still on her blanket when the cycle was finished. I had to rewash for another long cycle. Maybe its because it doesnt have an agitator. I was worried about this when I bought it and I will never by one again.

Extremely unsatisfied with their customer care. I purchased a washer and dryer 18 months ago and did not choose to purchase an extended warranty. I currently need a main control board replaced after the machine stopped spinning and draining. I hired a wonderful handyman, who originally suspected the lid--locking mechanism was the problem. When that was replaced and the machine still wasnt functioning, he determined the main control board needed replacing. This is a manufacturer defect and costs approximately $300 for the part, not including labor. Of course, my machine is no longer covered under the extremely limited manufacturers warranty that only lasts for 12 months, so I am stuck picking up the bill. Once done with all the parts and labor, its cheaper to buy a new washing machine especially because they still wont add a warranty to it after its fixed. I think its absurd that a manufacturers defect isnt continually covered under warranty no matter how old the machine is. Customer service continued to tell me I should have wasted more money on a company that doesnt care about customer satisfaction and purchased an extended warranty originally. Horrible investment! Will never purchase Whirlpool appliances ever again!

We purchased it from Best Buy. It was a good thing we got the extended warranty. They completely rebuilt it two times. In the 6 years we have had the washer. The motherboard went out. The bearings went out. The only thing nice I can say is that it’s a top loader and doesn’t get smelly like the front loaders do.

In 2005, I purchased a Whirlpool front-loading automatic washer for $700 plus. The machine had to have repairs on it several times at my expense. Then in 2010, I had to replace it and spent another $700 plus on the same type of washing machine. Whirlpool would only discount $100 of the cost. The second machine three years later is now also needing repairs. I spent a total of over $1,400 in 7 years on two washing machines not including repairs and parts. It also took forever to find the parts, so I went without use of a washer for one month. I called customer service and said they couldnt do anything for me the second time around with them. I will never buy another Whirlpool ever! You would think a company would care about their customers but they dont. They make their stuff cheap and charge an outrageous price.

Whirlpool cabrio top loader is junk from the first month. My washer has had way too many repairs. A&E repair has been a frequent at my home. Now Im getting ready to repair it again! Hub gasket or pump not sure this time. All has been replaced previously. Never ending - always something wrong with it!!!

Purchased Feb 2013 - worked okay until one month ago. Now stalls in the drain and spin cycle. The rotation of the drum sounds awful, makes a loud grinding noise. I tried doing the diagnostic reset of holding the Temp button in for 3 sec, release, 3 sec more but that didnt work. Also, I have noticed clothes are DRY after the Wash cycle! Managed to interrupt the wash and unlock the lid and was very disappointed. This is not a good quality piece of equipment. This seems to be a very common problem. How unfortunate.

I waited on hold for 24 minutes to be greeted by Audrey in Michigan giggling. I put in my service, need to be told I have to wait 3 days to have a tech arrive for A BRAND NEW REFRIGERATOR! To top off my disgust of WP, our BRAND NEW dishwasher doesnt work properly either. To wait, to receive ZERO voice of concern or even a fake apology, is disgusting to me. I am extremely disappointed! Shame on you Whirlpool! Shame on you!

Mtf18 defective refrigerator - The unit is 2 yrs old and about 6 months prior to 2014 I could not keep ice in the refrigerators ice (freezer) and the appliance compressor ran 24 hrs. a day without recycling or stop. I did not purchase an extended warranty, after all, Maytag the dependable company. The lonely Maytag repairman. Right!! The unit cost $$700. and is now an anchor. You cannot repair the compressor, only replace it...

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

Just want to pass on update on my dryer situation. Purchased a Whirlpool WGD4900XW1 3/9/13. The motor went out 6/22/15. Now Dec 2016 the replaced motor went out again. Whirlpool says... So sorry, we can get you a discount on a new one... ABT is giving me a break on the part so I am going to go ahead and fix it one more time. I assume in another 18mos I will be looking for a new dryer! DO NOT BUY WHIRLPOOL DRYERS. THEY ARE CRAP!! My brother also purchased a Whirlpool & it died about the same time.

Reading the many reviews of malfunctioning washers and other appliances, I wonder why organizations like Consumer Affairs and Consumer Reports do NOT help the many cheated customers form a class action lawsuit or boycott or some other means to effectively organize and force manufacturers to return the full cost of purchase, taxes, shipping, moving and repairs for 5 years for every product. The manufacturer have NO consequences for selling shoddy, malfunctioning but terribly expensive products. We are all being taken for fools by the corporations.I was stupidly brand loyal and bought a Whirlpool Duet front-load washer and dryer because we had to leave our perfectly good 28-yr-old Whirlpool washer when we sold our house. The first set of instruction is to pull the electric cord from a small hole in the back of the washer. No amount of pulling would budge the cord. Finally yanked with all my strength, heard a snapping sound and 12 of cord came out. Then no more pulling, yanking or tugging would produce another inch of cord. So I took off the top of the machine and found the cord tightly wedged in the fork of a plastic thing that looked like part of a stabilizer for the drum.A similar plastic thing on the other side was broken at the fork, the snapping sound I heard. Freed the cord with lots of effort, but it was still firmly stuck way down inside. Removed the back of the machine, found the cord stuck inside a circular thing with one tiny opening. Took lots of time and effort to free the cord from that, but it was still stuck. Finally managed to reach the plug, which was firmly anchored to the bottom of the frame with an orange lanyard. Cut the lanyard with a knife to finally free the cord. This had to be an act of sabotage by an assembly worker, as no way could the cord accidentally jam itself into 3 different places too small for the cord to slip in, and it certainly didnt tie itself to the bottom of the frame with a lanyard.The hour it took to free the cord was just the start of troubles with this machine. It did start and kind of tumbled clothes in an odd fashion, but when it went into spin cycle, it literally jumped all around the room, almost jumping out the door. The whole house shook and I feared the floor would collapse. That machine must weigh well over 100 lbs. even without water and clothes. Next load I tried delicate cycle which had a slow spin cycle.Same result, even worse. I had to wedge my body in the 10 space between washer and dryer and press down with all my 170 lbs. to keep the machine from doing serious damage to the dryer, walls and floor. I contacted seller, Lowes, and they said call Whirlpool. So I did, but no response. Before buying that machine, I read many horrible reviews of Whirlpool Duet machines, but I have only owned 2 washers since 1967, both Whirlpools, so I had strong but stupid brand loyalty.

I purchased a WhirlPool dishwasher in 2016. The primary motor had to be replaced in 2018. WP paid for the part; however, I had to cover the labor, which was expensive. In 2019 the drying element broke. Again, WP will replace the part but leave me to cover the labor. Ive decided to purchase a new dishwasher (none of the Whirlpool brands) with a 5 year warranty. I will never purchase another WP product and recommend everyone avoid all of their brands. Heres the list of brands you should avoid. https://www.whirlpoolcorp.com/brands-we-love/

After 3 short years, my dryer that cost me over $900 is not working and the part needed for the repair is no longer being manufactured. They did offer the parts for free, but that was useless since they arent available. They then offered me a new dryer which would cost me $800. I am currently waiting for the Product Exchange Team to contact me. Im not hopeful that will be of any use.

Its a piece of junk. The only time it will finish a wash and spin dry is when it is empty. Otherwise, it stops and lists an unbalanced error code. I opened up the service panels and found no broken hangers or clothes. There’s no way to bypass the system. I have read of similar issues and of course, its just out of warranty. I assumed the warranty was like other brands but it’s much shorter. What to do? Purchase a washer with dials and not a brain; it will last years. Note that the models without a brain cost far less.

This is a good looking, inexpensive stove/oven. Stove top has four burners. I liked the split grates on the stove top. Its easier to remove and clean. I do not like the rubber seal on the oven door. I am used to the heavier duty seals on most oven doors.

Whirlpool Cabrio - I have had the same experience as those others that have written reviews - over $1,600.00 (on sale) - approximately 3 years old and I was just informed by a service repairman that water has leaked from the center of the tub into the motor and it is trashed. I went to the Whirlpool website to chat with a representative and they are sorry but unfortunately, we cannot guarantee there will be no repairs or parts replacements needed as components do deteriorate or fail on occasion due to factors over which we have no control - they went on to say that since the washer is approximately 3 years old there would be no assistance that we would be able to provide toward repairs. I agree that a class action suit should be considered since Whirlpool is taking no responsibility for a machine that costs too much - makes your clothes smell and lasts for such a short time. Highway robbery!! The dryer is no better but at least it is still working (today anyway!).

Whirlpool Cabrio washer - I had all the same problems as all the 900 others on this site. After 7 months, it died. The factory repairman told me it needed a new transmission and motor. I returned it to Costco for a full refund and did a lot of research and bought a Speed Queen. It has no computer. It’s just an old-school washer that cleans, and best of all, it’s made in the USA with a 10-year warranty.

I purchased Whirlpool dishwasher, model DU930PWSTO, in 9/2007. It quit working in 5/2012. I expected an appliance made by a reputable manufacturer (Whirlpool) to last longer than five years. It seems like a manufacturing racket where they build these things only to be replaced a short time later. With service calls and parts replacement, its cheaper to buy a new unit. Talk about a circle jerk! And who the heck puts anything else but SS screws in a water soaked appliance? Duh. Rust! Im disgusted and dissatisfied with the whole company. Im still waiting on their response to my complaint email; at the time, the machine quit working. Whatever happened to pride in American made products? Or, did this get company bail and were now slaves to the Chinese junk once again? Ill never buy another Whirlpool appliance again. Does anyone have anything good to say about this company? I wish I would have read this blog before purchase.

I have a double door refrigerator with a bottom freezer. It is slightly over 2 years old and has been in use for only 7 months of that time. We just got off the phone with Whirlpool service. They will cover the cost of the control panel and defrost control. The other one I paid to replace was only one month old and it failed again. In the time between that I had to have an Icing kit put in as the Ice maker was causing ice to form inside the back wall of the refrigerator. My first call to Whirlpool was very unsatisfactory. I ended up paying for the part and the service call. The second call was about the ice-maker and they were aware of the problem and sent me a repair kit for the problem. I still had to pay for repair service. So far I have paid $561.62 for their defective parts and service calls. This time my wife called (while I was taking my frozen foods to my neighbors freezer for the second time) and went through 3 people before being told the part was still under warranty and they will send a new one. When we pushed for proper service we got it. We should never have had to go through all this. We also lost over $300.00 of frozen foods. Never buy a Whirlpool refrigerator!!!

Do not buy Whirlpool or Maytag appliances. They do not stand by their products. We have purchased 2 washing machines in the past 8 years. Both of them quit or broke almost as fast as we got them. The customer service agents were pleasant, but they would not help us at all. The machine we purchased has a design flaw that they will not acknowledge. They have been contacted by us several times and cant fix the problem. They need to correct a design flaw that is in all their machines.All of our clothes get encircled around the agitator and the machine gets off balance. We have to untangle our clothes from the agitator and pull them apart by hand. They make bad products, including a Whirlpool refrigerator that broke within a month of us buying it. They care about selling these crappy machines. Buy a GE, Bosch or LG. You will get a machine that works properly as soon as you hook it up. We have had their representative out several times to our house and they could not repair it. The repair techs have told us that Maytag and Whirlpool clothes washers are no good.

Cabrio fabric washer and dryer sucks. I gave almost $500 for a piece of **. Doesnt get the clothes clean. Hell most of them dont even get wet. Its junk. Wouldnt have another one. Lowes junk and the dryer aint know better. Its always flashing check lint even when its clean and you have to ** with it just to get it to start.

Since my review I have been corresponding with Whirlpool Customer Service (Chris). First he sent me an email and mailed a replacement board to have us (the homeowner) install. Because the cover was so melted, the replacement board would not fit down into it. I emailed pictures to Chris. Once he saw the pictures, he called me and arranged for the water heater to be replaced since it was still under warranty. He even extended the authorization code so we would have plenty of time to arrange for a plumber to do the work. We had to pay for the plumber, but Whirlpool arranged for us to have a new water heater. Now I can sleep at night without worrying that my house would burn down if the old water heater caught fire. Chris was GREAT to work with. I had a direct number to him and called any time I had a question. I was very impressed with Whirlpools Customer Service.

My washing machine is just over a year old and it has ruined so many clothes... They come out with brown stains on them... Almost like a oily stain. Not sure where its coming from but its either Im gonna have to buy a different machine or keep buying clothes. My husbands t-shirts look terrible... If any suggestions to what it can be please respond back to me. Thanks. Model# wtw4815ewo. Serial# c51433710.

Whirlpool Dishwasher is 5 years old. Used in a one-person household where dishes are washed approx.. every four days (rinsed before placing in d/washer.) Recently at completion of cycle, 2 of water remained on the bottom (still there.) Whirlpool told me it sounds like I need a new pump, the cost of which would be approx. $300 (tech visit and evaluation, parts and labor.) I understand appliances dont last forever but I expected more than five years.

I purchased a Whirlpool Ref side by side 11-2013. I have had nothing but trouble. First the Ice maker leaked, was fixed. The door to the ref has had serviced 5 times. The tech after many times trying to fix hinge on door twice was told to order new door. This took 6-8 week to get. Came today 5-27-15 too but new door on. It is still not right, has big gap in the middle - still not level as should be. I have called Customer Service again today with no help. All they want you to do is spend more money on a contract. I THOUGHT WHIRLPOOL WAS SUPPOSED TO BE A GOOD PRODUCT......NOTTA....WILL NEVER BUY THIS PRODUCT AGAIN. SO IF YOU EVER BUY WHIRLPOOL PRODUCT BE SURE TO GET EXTENDED WARRANTY. YOU MIGHT NEED IT..........STILL NOT SATISFIED AND NO HELP IN SIGHT.

I have been blessed with my washing machine. I have never had one problem with it. I have had my machine for over three years now. It is a reliable machine, with five different water levels from small to super. It also has three different water temperatures (just great). I am very pleased with my washing machine. I cannot tell you how many machines we looked at before selecting our Whirlpool, thank goodness we did.

I just purchased a new Whirlpool 6th Sense hot water tank #333570. This unit is a piece of garbage. Whirlpool should be ashamed at the quality of product they make. This unit came with a bent temperature and pressure relief valve, which required a piece of copper tubing to be bent awkwardly just to remedy the situation. Also, the control box is set at 12 (most other brands are 14, which is common), forcing the gas lines to be re-piped (very expensive). This unit also is extremely noisy, runs really, really hot and is not energy-efficient at all. Shame on me for not researching this product more closely. If youre buying a new hot water tank, steer clear of Whirlpool products.

My parents bought a Whirlpool washer machine and the machine was fine for the first two years, then water started leaking from the bottom of the machine and no one has yet to fix the problem! They have the worst customer service department. The A&E worker who came to my parents house smelled, wasted a bunch of time working on the machine and didnt fix anything! The A&E worker visited my parents house over 10 times and the problem still wasnt fixed! They (worker) have ordered parts after parts and still water keeps running from the bottom of the machine! Someone, please help and cut Whirlpool from the stores! Ive spent almost a whole on the phone trying to help out my elderly parents! Its ** and a lot of headache! Never use Whirlpool; theyre all crap!

Our dishes always come out completely clean and without spotting. I dont like having to get down into the machine and clean out the filter/trap, so I pre-rinse everything that goes into the machine, so that might help. Regardless, this machine does an excellent job. This is the Whirlpool Gold Series bought in 2013. It has numerous settings, such as delay, varying cycles, air dry, heat dry, etc. All the features work as expected, but like most owners probably do, I leave it set on the same settings all the time. It does what I want and does it very quietly. This is a standard, under-counter, full-sized machine. The outside of the dishwasher is stainless and the inside has a plastic lining. The controls are at the top of the front door, so that leaves the front completely clean-looking. Love it.

The refrigerator does what it is supposed to do. The fact that I had to have it repaired only after 1 year of ownership confounds me. The space in this side by side is a bit crampy. Seems like Im always shuffling things around. I truly believe that Whirlpool made the condensation tray underneath the unit out of cardboard. It literally disintegrated and started leaking after about a year and it was 200.00 to have it replaced by a repairman. The water filters always tend to piddle on the floor too. At least I hope thats what it is, and not another wilted tray!

Horrible. We purchased the set In October 2010. It worked great for a little over a year. (Go figure, just out of the manufacturers warranty.) The washer stopped spinning out water. Every other cycle completes successfully. The diagnostic cycle is also successful but once there is clothes in the machine, it wont spin. I called customer service and was told that a one year warranty was $230 and service is $130 plus parts. After reading another horror story, it seems that this venture is going to cost us around $450 for a new circuit board. Where is that class action suit at again?

July 2017 I purchased a Whirlpool refrigerator Model # WRF757SDEM00 S/NK51709722. The refrigerator portion went out, the repairman said it was the fan therefore I spent 351.00 dollars for house call and fan. When that did not work the repairman spoke to whirlpool and they said the panel of small computer may go out with it 212.00 plus tax. Did not allow that and tried another repairman who said the value that switches from freezer to refrigerator was out and if I could find someone to fix it would cost between 600 and 800. I went out and bought a Samsung because on the front said 10 year warranty. At least anything is better than 1 year whirlpool offers. There is NOTHING in the name.

This washer is poorly designed. Less then one year old and always has problems. I dont feel it cleans the closes. Does not always spin them. The load and go is a joke - had a service call because it would lock up - was told load and go does not work and not to use it - the washer was only a few months old. Now it will not even turn on!!!! - All other appliances work in the outlet - it does not respond. I will not even wash by good clothes in it - I take them to my daughters Samsung. I am in my sixtys and this is the worse washer I have ever owned, DO NOT PURCHASE.

Whirlpool double oven. The electronic control board has been replaced twice and needs to be replaced a third time after less than a year. The thermal fuses go each time I run the self clean. Whirlpools response has been disgraceful, trying to blame the problem on faulty installation when thousands of people have had the same problem. Ignore ANY US companys product; their warranties are worthless and they repair, not replace. My next oven will be European because in Europe they have to automatically warranty for five years any consumer durable. Consumer Reports ratings are worthless since they dont include breakdown experience in the ratings. Never buy anything from Whirlpool. They sell rubbish and dont honor their own warranty. Check the BBB rating. My brand new double oven broke down the first time that I ran the self clean cycle. Whirlpools response was to claim that the cutout opening was 1/8 inch too narrow and therefore they would not honor the five year warranty that I had bought from them. This was a lie, as I verified the width and it was exactly that required. Others have had the same experience. Whirlpool also makes Maytag, Kitchenaid, Kenmore and Ikea.

We bought our house in December 2010 and the water heater (fg1f4034t3NOV) just started to give me fits. I had the same pilot light problems everyone else encountered. The person at the 877-251-1679 number gave me a good tip and that may have fixed the problem in the short-term. They told me theres a screen for venting on the bottom of the unit and to use a bottle brush after turning off the unit to clean the screen. I did this yesterday and the pilot light has stayed lit. I called the toll-free number and was told the water heater was out of warranty, but they could send me the part to fix the heater at half-price. I ordered it and they waived ground shipping. I hope to have the situation fixed soon. I’m very pleased with the level of service.

Like the load sensor feature the best, so economical, the drum is oversized to wash duvets and heavy blankets. The fact that the washer and dryer are stackable makes them ideal for apartment living.

I bought a house and for the first time in my life, I was able to afford and buy all new Whirlpool appliances at Sears. I worked so hard all my life and was so happy I could get new appliances when I was almost 50 years old. Up until then, I could only afford to get used appliances. Even then I had to finance them with a credit card, only to be so sad and disappointed. They are without a doubt the ** junk I have ever had. I wish I could have all my old appliances back. My new Whirlpool flat top oven burns everything and has ruined all my pots and pans. I do canning every year and it has ruined my very old and heavy pressure cookers. Even when you turn the heat all the way to low, it burns everything. I called the manufacturer and they say they do not have to disclose that it will ruin your pressure cookers or burn everything. I am very angry I bought any Whirlpool appliances. I also got a new washer and dryer; they are junk too. They dont clean my clothes like my old washer and everything is so wrinkled up when it comes out of the dryer. I need to iron everything. I have never seen anything like it. I also bought a Whirlpool hot water tank that has now gone out 2 times in 5 years because the thermostat burns out. I pray it doesnt burn my house down one of these days. One of the times it went out, I was about 10 feet away from it and it literally blew up and about gave me a heart attack. It was so loud and scared the bejezzers out of me. Whirlpool, you suck. I have told everyone I can tell how much junk your appliances are. Your company should have to be accountable for selling people such **! I would sure like to be paid not only for the cost of these junky appliances but also all my quality pressure cookers, ruined clothes and distress this has caused me. They have no consequences. They have gotten away with ripping people off and giving a lot of us tons of stress, stress, stress, and anxiety, not to mention all the financial cost. Thanks, Whirlpool, you piece of junk! I think if I had not worked so hard to finally get what I thought at the time were high quality new appliances, I wouldnt be so affected but I dont have the money now to get new quality appliances. Whirlpool took my hard earned money for their junk.

I purchased a (second) Whirlpool washer (WFW87HEDW0) in October 2014. Since purchasing (and to this day), I manually dried the rubber gasket after completing my daily washes, knowing that mold growth was possible. I wash one to two loads of clothes about three to four days per week. During the first year, I did not notice any mold in this area and was confident that the manual drying and cleaning with Affresh was preventing mold growth. However, at the beginning of this year I discovered a little mold growth, which has slowly been increasing, in the inside lower lip of the rubber gasket. The image attached reflects mold in its current state. I was very surprise to see this happening since my diligent cleaning has been thorough and never ending. I even remove the soap dispenser tray to clean and air dry it outside of the washer and leave the washer door open at the end of the daily washes for extra fresh air circulation. This is my first official complaint about a Whirlpool front loader washer, even though I previously owned another (GHW9200LQ0) before this one and had mold growing on the rubber door gasket but, unfortunately, never officially complained about that old machine. Now, I dont qualify for the $500 compensation because I never officially complained three times within the first five years of owning the old washer. To my dismay, I did not immediately realize I had mold growth in the old washer. It was only until years later that a repairman told me that I had mold growth in it. In addition to telling me the price of replacing the rubber part and replacing a broken water pump plus labor would cost as much as buying a new washer. Before purchasing a new washer, I researched and read many reviews about Whirlpool and other brands before deciding on this new Whirlpool. I decided to give Whirlpool another chance and to follow their recommendations on the proper cleaning of the machine. Once again, I am disappointed and angry with Whirlpool and, now, have to figure out what to do with my current situation.

We had Lowes install a Whirlpool model Nu40T121-403 natural gas water heater early October 2012. The temp controller went out in October of 2014. I replaced the controller myself at a cost of $30 for overnight UPS from the manufacturer, American Water Heater. The controller went out again almost exactly one year later and I again replaced it for the $30 shipping charge. In both instances the customer service person told me the malfunction was probably due to my not flushing the heater annually, causing a sediment buildup. The water to the heater not only flushed annually, but is filtered through a water softener and there was absolutely no evidence of sediment in the drain water or on the part of the control that is in the tank. Now it has stopped working a third time. I called Lowes about replacing it, but they only carry Whirlpool, so wont be buying a replacement from them.

The lid stopped locking just over one year after I purchased a Whirlpool Cabrio top load washer, which disabled the washer from washing. After investigating, it seems the electronic control board needs to be replaced, which will cost $400 just for the part. I have a large family, including a disabled child, and a washing machine is mandatory necessity that I cant afford to replace after only one year.

We purchased our Whirlpool dishwasher/Model no. WDT780SAEM in July 2016 and it was installed on August 3, 2016. Right away we noticed 2 problems. The top tray squeaks very loudly when being pulled out for loading and unloading. The usual temporary fix for this would be using a product like WD-40. Of course as soon as you run the dishwasher all of the product is washed away. This was our first complaint about this dishwasher. The more important problem was the white cloudy residue being left on all of our clear plastic cups and glasses. Weve always had hard water but our previous dishwashers were able to remove the residue if we used the high-temperature wash. After looking at all of the manuals and user guides that are included with the purchase we read that we should be using a rinse agent and a product such as Lemi Shine to deal with hard water deposits. We tried these items and nothing worked.Using the All Fresh tabs didnt help and our filter was clear and clean. So we made an appointment to have the Whirlpool factory serviceman come out to look into our problems. First of all the customer service representative I spoke with was rude and impatient. She kept cutting me off and asking me about hard water and suggesting that I use all of the products mentioned above before finding out that I already had used them to no avail. Because we had the dishwasher for just over 30 days I asked her about the Clean and Quiet Guarantee that I found out about by going to Whirlpools site. Her exact words were The clean and quiet what?? So I didnt have much hope for our service appointment. Our serviceman was asking all of the same questions about hard water and if we had tried all of the products I mentioned above.After his visit we found out and now (too late) know that because our new dishwasher does not have a heat booster or the ability to get the water temperature high enough to remove the hard water residue theres nothing Whirlpool will do for us. This is the case with all newer technology dishwashers UNLESS you purchase one with a heat booster. I sure wish this wouldve been made clear to us, the consumer before making our purchase. If we had known beforehand that new dishwashers no longer get the water up to 140 degrees which is what would be needed to remove the residue, we wouldve made sure our model included a heat booster. Now were stuck handwashing our plastic items if we want clear dishes. Its not the end of the world but its not good customer service or honest to the consumer in any way, shape or form.

Whirlpool Clothes Washer Model WTW4930XW1 - We have experienced tub overfilling on (2) separate occasions with this washer model in a period of time of less than (2) years. Through extended warranty service purchased, a technician came out the first time; declared nothing explainable to cause the malfunction, re-calibrated the control panel, and off he went. This second event occurred much the same as the first; happened to walk in to notice water on laundry room floor and witnessed overflow out the lid on top. We have carefully washed additional loads after this second event without a similar malfunction. From my online research, this sure sounds like a faulty pressure switch not sensing high water level in the tub. Any other thoughts?

In 2002, I purchased an EE3Z50RD055V 50 gal. Whirlpool hot water heater. Recently several solder joints on the computer module became unsoldered so I cleaned the joints and resoldered them. But several months later another joint became unsoldered so I thought Id just purchase a new module. I called 1-877-817-6750, explained the problem to the young lady. She informed me that they would ship me a new one overnight. I asked her how much this would cost and she told me there would be no charge as it had a lifetime warranty. SURPRISE! Thats what I call customer service! A few years ago, I purchased a Whirlpool Duet front load washer and dryer. Now Im twice as glad that I did. My wife and I LOVE the Duet.

I am very reluctant with online product feedbacks. But here is one story that needs to be told. I purchased a Whirlpool 3D Split AC 2 years back (and hence the product is out of warranty). The product quality is so bad (and unreliable) that within 2 years the coils in the Outdoor Unit have started to leak. When I requested for service visit the technician (so called) came over and did a wet service and took the fee (without an invoice). And assured that the AC would start to work fine. Within a week we realized that the AC is not cooling enough. Again a service visit was called and this time the technician (supposedly) diagnosed the above problem. The repair cost told to me is to the tune of Rs 10,000/- for a product cost of Rs 36,000/- (or so) bought just 2 years back. Does anyone in Whirlpool understand what QUALITY means??? Does anyone understand VALUE FOR MONEY... This aside I have a 2 Tonne Whirlpool AC, 350 l Whirlpool DD refrigerator and a Washing Machine... I think its time for Move over WHIRLPOOL and HELLO MITSUBISHI, BOSCH, HITACHI... End of a great consumer brand...

I love my Whirlpool Washing machine. Purchased it 2 yrs ago & have not had any issues. Its quiet, large capacity. Washes my clothes very clean. The various washing cycles makes it so convenient to wash as much or as little as I need on any occasion. I do recommend to anyone that you do the cleaning cycle on these new washers to ensure top performance when washing.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

A whirlpool water heater model FG1F5040T3 purchased from Lowes five years ago developed problems, which could not be fixed. My problems started two weeks ago when the pilot light would not stay lit eight hours at a time and then nothing. Having a service plan through our utilities, they were notified not once but as it stands now, 6 times. Six techs have been out to my house and replaced the thermocouple twice and a complete gas control valve. The pilot still will not stay lit. Supervisor contacted Whirlpool on Thursday. Now its Saturday and no word from Whirlpool and no hot water. Try to get assistance from Whirlpool after work hours and it is impossible. This tells me that they do not care about their customer or the product that they make. Do not buy Whirlpool products!

I purchased my Whirlpool washer and dryer 4 yrs ago. I was planning on purchasing Samsung but the saleswoman at Gils in Bristol, RI strongly recommended this junk!! A washer and dryer should not quit after 4 yrs w/ a household of 2. The dryer never dried properly. Each load took 2 cycles. Yes, repair were called and we were told its a design flaw. The washer just stopped spinning. Repair will would have been $550. These pieces of junk were replaced by GE electric stackables. Fingers crossed....they are working satisfactory!

This is an ongoing problem. I have had to thaw the refrigerator (which takes over 24 hours). Then I blow out the drain with my air compressor, run water through, etc. The drain freezes up a good way down. It is a big pain in the **. There has to be a design flaw for this to continually happen. I paid for a repair man one time but he did nothing different from what I am doing. I cant afford the prices they charge. Shame on Whirlpool for making inferior products.

My appliance is less than two years old, and it wont stop heating. I have to manually turn it up and down to heat water, which seems strange, since most or all of the complaints are because it wont stay lit. Mine stays lit (knock on wood). It wont shut off. A new thermostat costs $60.00 after two years? Please.

Whirlpool g2 convect/micro over the stove oven - This top of the line oven is JUNK, KEEP YOUR MONEY-DO NOT BUY THIS JUNK! I have had problem after problem. Starting after only three months. Defected door switch, touch screen, flashing screen, error message. The service repairman and I are on first name bases. Thank goodness for the, out of my pocket warranty which I no longer plan to keep. I NEED A OVEN AND DEFINITELY NOT A WHIRLPOOL.

Never ever go for Whirlpool. It has the worst customer service. We brought an oven but accidentally we broke the inner oven plate. We called up the customer care person on 18002081800 and tried asking him the dimensions of the plate pr at least how we could reorder it. He never listened to us. He just got our details. Said that technician will come at 11am tomorrow and disconnected the call when we were trying to explain what our query is all about. Is that all the respect a customer deserves!? Is that how whirlpool trains their service people!? He doesnt even have the basic courtesy to listen to the customer, I wonder how was he even recruited as a customer care person. If you want at least your basic respect, please DONT BUY WHIRLPOOL.

I purchased this washer over 8 years ago and we have been using it 3 to 4 times a week/ 52 weeks a year since. It has performed flawlessly up until about a year ago when it kept given me uL error. Everytime I wash the basket always spins wobbly and unbalanced it seems. I checked the Internet and it turns out others have had the same problem. The solution was to replaced the 4 springs supporting basket and that fixed the problem. Been working ever since.

Very sad appliance company. I purchased a Standard Pacific Home in June 30, 2015 and moved in Aug 1, 2015. Use my Whirlpool Dishwasher for the first time back in Oct and it was not working properly. Whirlpool scheduled an appointment with Accord Appliance in Temecula Ca and the company was a no show. Called Whirlpool back and Rep Emma was very rude and had to call supervisor to schedule another appointment to repair dishwasher. Whirlpool have sad employees and sad appliance.

This washer never worked right. It simply mixes the clothes up with little water. A real piece of crap. See the 2000 other complaints. Time for class action suit.

Bought a new Cabrio, worked ok but in less than 2 yrs the bearing is bad. It will cost almost as much to repair as a new washer. Will never buy a Whirlpool product again. Would give negative rate!

The tub mounts of my 6 years old Whirlpool washer are broken. It’s too expensive to replace. Seems like built in obsolescence! Ive also had mold/odor issues. Finally, I know how to fix that, now this. I just want to warn others, these machines are not designed for the long haul.

The washer (Cabrio WTW7800XWO) was less than 2 years old and we had a motor go out, so we paid a repairman to come out and repair the machine. The total cost was over $300. Now 2 months later, we get another code on the machine and Whirlpool says, We are sorry but there is nothing we can do, but if you would like to pay $219, we can get a repairman out there to check out the machine and repair it. Theyre also giving the machine an additional year warranty. Shortly after that, I noticed the lid was not staying up when I opened to put clothes in it to wash. So since I was wondering what was happening, I looked at the lid and to my surprise, the springs that hold the door up when open are built into the plastic lid cover that has a see-through glass on it. Right where the springs are located, it must be a stress point and the plastic lid has since cracked and is almost about to break off. I am now in the process of ordering another lid and Whirlpool offered to sell me a lid for $226 but I think I shall buy it from someone else as I dont want to put any more money into Whirlpools pockets. We paid over $1000 when we bought this machine. Now it is about 2.5 years old. I hope there is a class action lawsuit on Whirlpool as I will definitely join in if there is. This company needs to go out of business if they continue to sell machines like this that have so many problems especially when they are less than 2.5 years old. Goodbye Whirlpool. You have lost many more customers as I shall be letting everyone I know about all the problems and complaints about this machine.

The dishwasher is noisy and the latch which holds the soap, at times sticks. When we think it is done and ready to unload we need to run it again because the latch that holds the soap DID NOT open. Not good.

Re: wdf7payw6. I purchased this unit last February. It has never washed properly. In the last month 2 separate warranty service reps have been out. The first one told me that I have not been doing a good enough job of prewashing the dishes so the arms were clogged. While cleaning them, he broke the top arm. When he came back to replace the top arm, he added that the dishes were not drying because I didnt use enough jet dry so I would have to dry by hand, and that the arms were clogging because I didnt prewash well enough. I told him to leave and never come back. I called customer service and they sent out a new company.The rep today told me that even on time delay or overnight settings I must run the hot water prior to starting the unit. And that since the water wasnt hot enough; the undissolved detergent was clogging the spray arms. This was confirmed by your phone support person who told me that for best results thats what I had to do. The result I want is for the thing to wash dishes. It doesnt do that. The current rep ordered a heater, motor pump and spray arms. My previous dishwasher operated perfectly (until the pump failed) for the 18 years I have lived in this house plus however long it was here before I moved in. I will never buy a Whirlpool product or anything built by subsidiaries or parent AGAIN.

I have been buying Whirlpool appliances most of my married life. Our most recent washing purchase is the worst machine I ever owned. I have ruined more clothes, rugs, sheets and towels, etc. than I ever have in my 45 years of doing my own laundry. In fact, I do not EVER remember a washing machine destroying any of my articles. I just pulled 2 almost new rugs out of the washer only to find they have been destroyed! I am pretty sure it is the extremely fast spin cycle that is destroying my items. I know it cant be the agitator because it doesnt move fast enough to even clean the clothes. And the stupid load sensor is absolutely worthless! It does not dispense enough water to even cover the clothes let alone clean them. Go back to the old machines that did their job without destroying anything and actually cleaned the clothes with an amount of water that I chose. I ABSOLUTELY HATE this machine.

We purchased the Whirlpool Duet Sport matching washer and dryer new in 2006 from a local appliance store. The washer was around $1,000. The salesman sold us on the load capacity, telling us it can wash 15 pairs of jeans. We dont overload it, mostly because its a high-efficiency washer and doesnt use much water (Im still trying to figure out the concept of how can you clean a whole load of laundry with a little bit of water). Its very quiet, but the cycles take longer than standard washers.Also, you must use very little soap (too much soap will cause the washer to stop and display an error code, which youll have to call a technician to come and reset). It is now 2013, and the washer started thumping during a cycle and there was a burning rubber smell. We called an appliance repairman who gave us an estimate for repair of $800 to $900 (for a bad bearing/bearing casing and inner basket). Im sure that there was quite a markup on those parts! It seems to me that the older non-efficient washers lasted longer than 7 years, and certainly didnt cost $1,000 when new.

Whirlpool sent me a different part 3 times and hot water tank only work for a few weeks, then the pilot light goes back out. They never offered any more help.

I wouldn’t recommend buying Whirlpool appliances. Hot dishwasher in December used 1 month and the board went out. 3 month to get a new then they install it and they sent the wrong user interface. Wait another month. Still no call. No dishwasher. Everyone I know has issues with Whirlpool appliances that are branded as made in US yet if they truly had good components that were made in the US they would get more customers back.

Ive bought two (2) whirlpool dishwashers in approximately two years. Both dishwashers stopped draining shortly after one year. I checked the filter, removed parts at bottom of appliance and checked the drain hose and my home drain to make sure that none were clogged. After testing the draining system a burning motor smell started to occur. At that point I disconnected and threw away the appliance. I dont know for sure but I think this is a recurring and known defect.

Love the bottom freezer & french doors. Unit uses way less energy than older fridge. Did need a new evaporator but it was covered by a recall. Happy so far. Love having icemaker in the door so it doesnt take up freezer space.

Gas control not working. I have replaced the thermostat twice in three years. Now, the hot water tank pilot will not light. The igniter works; a new thermostat has been properly installed, and the pilot will not light. The gas is on, and the tank has functioned. I just want a new gas control.

I bought a whirlpool Washer in 2011 which I bought an extended warranty. Thank Goodness! It has broken every year. At first I was ok since they always fixed it. It is very inefficient and the clothes are not clean. But today I am so ticked. It broke in Sept. and they have come out twice and cant fix it. Now they say it will be Dec. before they can fix it as part is backordered. REALLY!!! Im expected to not have a washer from Sept. to Dec. with no compensation! I have called both Whirlpool and the warranty company and they say thats just the way it is. I WILL NEVER BUY A WHIRLPOOL AGAIN. The warranty service is through Federal Warranty Service.

It gets the job done. Its no power washer, but the dishes get pretty clean and dry nicely. I have no idea how dirty the dishes can be and still get cleaned, since Im weird and pre-wash my dishes. Its stainless steel and black, and has quite a few wash and dry settings, including an option for heated or unheated dry. The utensil rack is attached to the door of the washer and cant be moved. Two levels, and pretty easy to do dish tetris with. No offense to most standard dishwashers – I need a washer about 3 times the normal size due to a passion for cooking. Its slick and matches my ultra-modern, borderline-Swedish interior.

From the time I had the Cabrio top load washer, it has been repaired at least 8 times. I did get the extended 2-year warranty. I should have known that this machine was going to give me problems from the first service call. I have had to have the motor replaced 4 out of the 8 times the machine has been serviced due to coins getting into the motor. I have a problem with rust around the dispenser. I also feel that the clothes get very tangled when washing. The machine is just 5 years old. This time when I called for repair with A&E appliance repair, they told me that it was going to be $450.00 to repair. Now, I am not going to repair it, especially after having all the problems I have had with it. I will never purchase another Whirlpool product or any of their other products that they make. I did call Whirlpool just to let them know my problem and to let them know that there have been hundreds of complaints with the same washer that I have. It’s too bad that Whirlpool has no respect, passion or pride in what they make. I am going to purchase a new washer and it will not be anything related to Whirlpool.

AquaLift cleaning system does not work. My oven was barely dirty and I had to scrub with the special sponge to remove baked on food after I did the cleaning system twice! Rust is also showing up on the drawer which they refuse to repair because it is ONLY COSMETIC! Stove is 16 months old.

Its very noisy, and there are no blankets to purchase to deaden the noise. The dishes all need to be dried by hand. Some of the dishes come out dirty. I would never purchase another Whirlpool dishwasher.

Three Whirlpool fridges in 5 years. 1. Fridge one three doors replaced still not satisfactory, returned, warranty VOID. 2. Fridge two simply stopped being cold therefore not working 100+ food wasted before year. 3. Fridge three freezer leaking all over floor. Two years old 0 warranty left. I now pay again to repair. I am so beyond WHIRLPOOL PRODUCTS and so fuming??? Mad. $$$. 1300.00 to 1500.00 purchases ALL JUNK. NEVER WILL I PURCHASE ANOTHER WHIRLPOOL product. I do own a full file of continuous complaints. Brault & Martineau store Gatineau did the best to help with exchanges, sent repair man who did nothing. Will not deal with them again either.

I purchased a gas range stove about three to four years ago. I am extremely dissatisfied with this Whirlpool stove. This is the second time the electric ignitors have been replaced due to the stove not working and it is still not working right. The gas valve regulator has also been replaced because it went bad too and my oven still isnt working. I have already put around two hundred dollars in and no one has any idea why it isnt working. Apparently these stoves are a real piece of ** and everyone is having the same type of problems. Something should be done for the customers as it is now. I will never buy Whirlpool again. What a piece of garbage!

In 2006, I paid $1,300 for above fridge and bought extended warranty. Within a year, I had four service calls for condensation in bins that causes freezing of lunchmeat, veggies, etc. and anything put in them. The A&E service company said to use plastic bags and then said I should keep the bin drawers open at an inch so air could flow. Next call said vacuuming underneath would solve it. Final call said again to use bags and suggested modifying the fridge by making a hole in the sidewall (which would nullify the warranty).Since I declined modifying the fridge, he contacted Whirlpool saying I declined service. I still have this problem, was going to call for service because I could really use the space the drawer provides but I have a feeling I will just be throwing money away. I was going to contact Whirlpool but Ive done that too. I feel totally ripped off on an item that should have quite a few years of service left.

Buyers beware of Whirlpool ovens! We bought a Whirlpool Built-In Electric Oven in August 2008. Fifteen months later, I decided to clean the oven for the first time and when I turned it on the auto-clean, the entire control panel went dark. The technician said he has seen this problem several times in such ovens and was able to repair the oven. I called Whirlpool and they had not heard of this being a common problem. Last week, the air blower wasnt functioning and had to be replaced. I called Whirlpool again and told them about this second incident in a 4 year old oven that is not used frequently. I told them their quality assurance people and/or engineers need to re-evaluate their products. My lesson learned is that I will never purchase another Whirlpool or Whirlpool related product.

This Whirlpool, two door, refrigerator with ice maker & water, replaced a very poor quality 'LG' refrigerator which had stopped working. The company, "LG" was not interested in learning what the problem was but was only interested in making sure we understood the fee for an "LG" repair person to come out. The set fee was a minimal of $150.00 without any repairs. We decided to toss the LG and went to our local Home Depot and purchased our Whirlpool that same day, on sale! Our Whirlpool has been working great, without any problems and the fresh, filtered water is always refreshingly cool. We would very highly recommend Whirlpool! It seems their products always work very well!

I bought an American US Craftmaster water heater in October 2006. I have paid a plumber 3 different times to work on this and the pilot light will not stay lite. I used the replacement parts they sent, followed their technicians directions over the phone, etc. Nothing seems to work. Christmas was not pleasant at my house this year. I’m still taking cold showers.

Whirlpool Duet Washer - The washer after 14 months started to rumble like a freight train under spinning condition. I call Whirlpool and the answer was to purchase an extended warranty or buy the parts for over $700.00 and pay the tech to fix it for another $250.00. A washer should last more than 14 months. I think the parts and the repair cost more that the price of the washer. This is a rip-off.

Four years ago, we remodeled our kitchen and purchased the Whirlpool Quiet Partner II dishwasher, with a one-year service warranty. To be fair, we have not had a problem with the operation of the dishwasher, but rather, the quality of the dishwasher. Within the first two years, the front panel of the dishwasher started turning brown and rusting through from the steam escaping the dishwasher. The labels on the operating buttons have peeled off, again, from the heat of the dishwasher. The upright spokes on bottom tray, that hold dishes and etc. in place, started rusting through and breaking off. Guides which allow top drawer to slide in and out and hold drawer in place, have weakened, so drawer is constantly dropping or sagging.I have had other dishwashers that have certainly lasted more than four years but was encouraged by a Home Depot salesman that this was a great machine for the price! I should have paid closer attention to that for the price part. In any event, I called Whirlpools customer service department, believing that in this day and age, SOMETHING could be done to help with these issues and was told, quite succinctly, that there was nothing Whirlpool could do. I asked about standing by the integrity of their product and got no response to that either.I am an associate with American Girl, a company that stands by the quality of its product FOR LIFE. To be told by a customer service rep from a much larger company, that there was nothing they could do to help me, completely blew me away. I have taken pictures that are pretty indicative of the quality of this dishwasher and will be going online to warn other consumers against purchasing Whirlpool products.

Its a 25 side by side and though its a large refrigerator it seems small inside. That being said I would probably not buy a side by side again. I have always bought Whirlpool made appliances and have been always satisfied. I do not like refrigerators with the freezers on top.

Purchased the fridge from hhregg in August/September 2012. Model G16FARXX. After less than three years of owning it, found out today that the compressor is shot and will have to be replaced. Replacement/repair costs are ~$900, almost as much as the fridge brand new. Chatted with customer support and then would/could not do anything. I feel ripped off. If it happened after 5 years of use, then my attitude would be different, but not a major component going out in less than 3 years.

I bought a new Whirlpool electric range in the spring of 2008 and purchased the extended warranty from Leons. The oven worked fine for the first three & 1/2 years, but then the bottom element in the oven seemed to have stopped working. The top element would still come on, in an effort to keep the oven at temperature, but was not effective.I called in a repair. The technician showed up, turned the oven on, noted that the bottom element did not come on properly & replaced the motherboard in the control panel with no further diagnosis. The oven worked for approximately 9 months and then the problem recurred. I called in another warranty repair. This time when the technician showed up, he turned the oven on & told me he was going to order a new bottom element, which he installed about a week later, again, with no further diagnosis.Now, here we are again, one month off warranty and 6 mos since the last repair, and again, the bottom element in the oven is not working correctly. I reported the issue & my dissatisfaction to Whirlpool and was basically told, How sad, too bad - hardware components fail and theres nothing we are going to do about it. Seriously? This range is just barely 5 years old and has a history of repeated problems with the bake function - obviously, something is defective in this product.I can see it, if I had not had any problems until this point, but when the same issue keeps coming up & obviously has not been correctly diagnosed and repaired, I would think they would have enough integrity to offer some kind of help or solution. Given the history here, its highly unlikely that Im going to be willing to spend big bucks on another attempted repair that, in all likelihood, will be merely a short term band-aid, so Ill probably have to buy another new range - which I cant really afford right now. Trust me, it will not be a Whirlpool & it will not be from Leons.

After reading endless stories regarding Whirlpool water heaters, I ended up here and read numerous complaints and every company response had the same message from Chris-- Go to whirlpoolwaterheaters.com/help. I went to the website and called the number (877) 251-1679. I spoke with the most helpful gentleman (Lenny) who helped me troubleshoot some things and even called me back to inquire regarding success and gave me other tips to check if the problem occurs again.

Whirlpool refrigerator runs continuously, but doesnt cool. I have to turn it off manually to cool down the motor. I have to run it on the highest number (5), then freezes some things on the top shelf but lower shelves are warm. We need these refrigerators and freezers replaced with different brands of our choice!

In defense of Whirlpool, I will preface my question with the fact that I did attempt to call them and they were closed and Ive used manual to troubleshoot. Problem: when I cook any baked good in top smaller oven, the cookies, etc. on front of pan closest to door bake even and are not burned. All cookies on back half of sheet are burned and not cooked thoroughly. Any advice or similar experience to share would be so appreciated.

I purchased a high dollar built in side by side fridge with custom panels in 4/2005 and had my first service call in 5/2005. Since 2005 we have had 11 service call mostly for defrost failures and over temp. readings. From 2011-11/20/2013 we were issue free then the fridge over temp alarm sounded and we could not hear the fan motor. We had the certified tech come out to evaluate and found that the main control board needed to be replaced. Kitchen Aid/Whirlpool no longer make this item and forwarded us to Core Centric solutions to have a new one built. After speaking with the certified tech who had been out to service our fridge 11 times he informed us that these boards in his experience have never lasted more than a year. We spoke with a customer service rep a Kitchen Aid and asked about a prorated discount on a new built in fridge and she said it seemed reasonable but after checking for authorization informed me I needed to have the board rebuilt at my own cost and that even though this typically takes about 4 weeks to build the fact that our family would be without a fridge is not Kitchen Aids problem. 6/20/2005-over temp/not cooling call (replaced defrost thermostat) 9/2005-over temp/freezer iced over in bottom (freezer decided and drain unclogged) 10/05-over temp/not cooling (replaced fan motor) 9/06-over temp/freezer iced over in bottom (drain line decided, kitchen aid had no advice on how to fix) 10/06-over temp/not cooling, ice build up (whirlpool recommended replace heat kit and bimetal) 11/7-over temp and ice buildup in freezer with leakage (adj to drain pump and defrost drain basin made) 11/07- over temp and freezer icing over (whirlpool sent out a new heater probe) 6/08-over temp and ice buildup (bimetal and foam block replaced) 10/09-over temp, lights and motor shutting on and off (replaced defective board) 10/09- fan making excessive noise (ice buildup found on evaporator fan)11/13-over temp ice buildup in freezer, burning smell from fridge and no air movement or cooling in either compartment (need board rebuilt as on 10/09)Board no longer available from whirlpool, must be custom built at owners expense and will take up to 4 weeks. D/t continuing issues and whirlpool not willing to help the customer with replacement I would highly suggest no one buy a Kitchen Aid fridge.