This machine has been very reliable. We have had since 2001 and have had not issues, Im really not sure on how clean our clothes are. Sometimes they have a odor but this is common with front load washers. I leave the door open and put baking soda into the machine regularly. Also clean the rubber seal because mold will accumulating on it.

I have many rentals, and for over 39 years have always bought Whirlpool dishwashers for them and my own home. I have noticed over the last 15 years or so they are getting more and more poorly made. First I quit buying the plastic tub ones because they collected mold on the back. Then putting one in a rental, we went through 3 brand new ones that all leaked before we got a good one. Now, I bought the very best for my home 2 years ago, had the pump replaced under warranty due to leaks. Now, the plastic upper rack wheel has snapped off its plastic base. For under 30 dollars you get a replacement kit for it, that is all metal. So why didnt Whirlpool just put in the metal ones and charge a little more. So this will be my last Whirlpool, and all the brands they make. Do your research, many of the name brands you know are all made by Whirlpool.

Retail price, $3100. Purchased from Sears Outlet for 2/3 of that amount due to dings on a side panel, back and some blemishes on the front. Still sold as new with a new warranty (Good thing!). Ive had full use of the unit for 1 month out of 3 that Ive had it. Freezer stays at a temperature in the mid-20s and, after 4 repair visits, it turns out the compressor is faulty and now Im waiting for the 2nd part to arrive and be installed to see if that corrects the problem. Sears stepped away from the problem saying it will be repaired. Whirlpool has wonderful telephone support that is totally committed to me staying with a faulty appliance until its fixed. My view is that a unit that expensive, should be no problem to replace allowing Whirlpool to take as long as they want to make repairs and re-sell it. But no; their commitment is to keeping the refrigerator in my house and running a service tech back and forth while I continue tossing food that cannot be used.

Just wondered if anyone else has had a problem with the paint bubbling up and peeling off their washer and/or dryer. My washer and dryer are in my laundry room off the kitchen with a heat and air vent in the room and I dont understand why my paint is doing this. They are about 5 years old and have always been in this room, never in a garage or basement. My dryer was rusting on the outside about 3 years ago and even though I bought the extended warranty, Whirlpool said it was only cosmetic and they wouldnt do anything about it. I bought them at Lowes and they were good enough to give me a new one to replace it. Both of the machines now have the paint bubbling up and peeling off and there is nothing that can be done. Anybody else have this problem and if so what can be done to repair the paint? This is my 3rd set of Whirlpool washer and dryers over the past 44 years and I will purchase another brand next time.

Purchased on 04-26, professionally installed on 04-29 into a clean, large, well-ventilated area within the garage. Has turned itself off every day since then. Flashes code 10, screen is dirty... Pull the burner and the screen is clean. Called Whirlpool. They tell me to clean it again, so I do. This goes on for weeks... I can now pull the screen and clean it with my eyes closed. I get up a half hour early every morning to complete my water heater re-lighting procedure so my family can take a warm shower!!! Whirlpool gives me a phone number to a repair company. They tell me the repair person will have parts on the truck. I wait four days, guy comes out and says, You need a control valve.... did they send it to you? So I had to call Whirlpool back and order the valve... three more days... Very next day after repair, the thing shuts itself off again! I call Whirlpool and they try and push me off to the repair company, saying they are now responsible for the repair, but in the same sentence the tech says the heater needs a burner assembly. Okay, so you know it needs a burner assembly, but you ask me to contact the repair company to come out and fix it knowing they DO NOT have the parts on the truck? Only after I change my tone and raise my voice does she offer to send the part ahead of the repair appointment! In my opinion, Whirlpool has reached the top of a list shared by other mega companies like Bank of America and Time Warner Cable... Too bad the accolade is for the worst product and customer service. DO NOT BUY Whirlpool.

I purchased a washing machine in year 2002. It was working perfectly. Recently, its drive belt started slipping. I called local service center, S. R. Enterprises, with mobile number 9204792391.The technician came after 3 days and declared that the gear box is leaking and will have to be replaced. They had no gearbox in stock for model f45, top loading, fully automatic.After a wait, they took away the machine to their workshop on 30.09.2011 and returned it on 04.10.2011.They charged me Rs. 4,730. I will have to be replaced. I found that its LID, which was perfectly okay, is now making a terrible sound when opened and would fall down, not allowing to load the machine. I informed the service center immediately. After many reminders, a man turned up yesterday and declared that the LID will have to be replaced and I will have to pay Rs. 2,000 for that. I rang up the service center to say, Since it has been damaged in your workshop, you should replace it free of cost to me. Their reply was evasive and negative. I called your call center and they registered my complaint - customer number **, comp. number **. I was assured that the LID will be replaced within 24 hours.

I purchased a home that came with Whirlpool appliances. I begged the company for GE or Maytag. Of course they went with the cheapest they could find. I must admit the microwave gets very hot but the dishwasher is a piece of crap! The water doesnt get hot and the dryer doesnt work. They tried to tell me it NEEDED Jet-Dry. I own 4 homes and have lived in all of them. Ive NEVER used Jet-Dry and all the others work perfectly. Run as far as you can from Whirlpool!

In July I purchased a Whirlpool Gold oven and cooktop from Lowe’s. It was delivered in Aug. after a 5 wk wait, since it had to be ordered. Since installation, the hot surface light on the cooktop stays on. I called in & was told to try resetting the elec. breaker. Did that... still stays on. Model G7CE3034XB00, Serial D43005649. On Sept. 4th I called & spoke to Carrie (I believe in TN) who told me she would try to find a service tech in my area & would get back to me in 3-5 days. Apx. 5 days later she called & left a message on my cell phone stating that she could not locate a service tech in my area. I would need to find my own service tech & submit any invoices to the resource dept for reimbursement. Parts could be ordered at no charge. I have nothing in writing from the company to confirm I would be reimbursed, nor was I told how to correspond with the resource dept in the event I had an invoice to submit for reimbursement.Today, Sept. 18th, 2014, I called Whirlpool again (800-253-1301) & talked to Stephanie in Michigan. She told me the same info. When I asked to be sent a wiring schematic I was told I didnt need one. When I asked how to get in touch with the resource dept. I was given a fax no. & email acct. When I asked how I was supposed to get in touch if I didnt have either, she said I should go to the local library. Now lets imagine for a moment that I am disabled or live so far out in the country that I cannot get to the library... How am I supposed to get to a fax or email acct. Has anyone at Whirlpool considered that? This is a new appliance under full warranty, yet it has become my job to find a service tech, pay up front, & wait for reimbursement. REALLY??? I am also in the market for a new dishwasher & you can bet it wont be a Whirlpool!

Our new fridge, which was already an exchange from another unit that went bad, kept freezing things in fridge compartment. A tech was sent out three times and then the compartment quit working completely. They stated they would replace for us, only way they would replace was to have them ship a new unit which would take two weeks. So we are without a refrigerator for two weeks. Asked if I could go buy one and be reimbursed. I could but I would NOT be reimbursed for full amount. The company reps I spoke to could have cared less about our situation especially Fred who supposedly is a supervisor. Do yourself a favor...DON’T buy Whirlpool. Their customer service sucks!!!

We purchased a Whirlpool Energy Smart Electric Hot Water Heater with a 12-year warranty from Lowes on August 30, 2010. The water heater stopped working and the green light was flashing three times. We contacted Whirlpool since it was less than two years old and they were very rude to us. They told us it was the sensors and we would have to change them out. We waited while they sent the sensors to us. We installed them and it still would not work. It continued to flash three times just as before. We contacted Lowes where we purchased it and they were extremely apologetic and said they would be glad to replace it if we could get an RA number from Whirlpool, but that many others have been having a hard time dealing with Whirlpool. We contacted the rude people at Whirlpool again. They said they were not surprised that the sensors did not fix it. We asked for an RA number so we could get a replacement (after all, it did have a 12-year warranty). Now we were days later with still no hot water. Now this rude technician said it was probably the control board. I asked him if we were going to have to be without hot water until we changed every part on the unit. At this point, we just took the hot water heater out, put it on the curb, and went and purchased a different brand. Whirlpool has lost us as customers for life. If their other products are as horrible as that hot water heater, I wouldnt take any if they paid me to. They were by far the rudest and most hateful people we have ever dealt with and life is too short to be treated that way. I predict they will be out of business in no time with the garbage they are putting out.

My gas range doesnt work all that well. Sometimes the flame catches and lights, sometimes it doesnt. Oven seems to be less than steady in cooking. It is ok, but I wouldnt buy again.

I came here to see if others have had problems with their Whirlpool Cabrio top load washers. I was amazed at how many others forked over nearly a grand ($1000 with tax and extended warranty) for such a heap of nothing. I have lived in the same house for over 35 years, same water supply with water softener. Over this time, I have raised my family and been lucky enough to only go through two washers until 2 years ago when I purchased this Whirlpool Cabrio machine at Lowes. As with others, clothes do not get cleaned. Residue is present and in the creases of the tightly spun and tangled load. After calling Whirlpool and Lowes on nearly day one of my original purchase, no concern was given. Instead, I received the What type of detergent or Could it be your water supply? or What degree of soil does your family have on their garments? A white terry cloth washcloth should not come out grey, even after bleach! My GE and Maytags of the past always did fantastic jobs. They just plain old wore out. As for my new energy efficient machine that takes 86 minutes to wash a load, with expensive HE detergent, an oxy clean pouch, special fabric softeners, I scratch my head wondering how can this be efficient? If a pair of jeans needs pre-soaking, it cant be done in this washer. Instead, I spray the jeans with pre-soak, add my HE products, then fill a mop bucket full of water and dump into the machine 5 minutes after the 86-minute session has started. What a joke! For two years plus, I have vented to my poor husband who thought he was buying me a new innovative state of the art machine to make my life easier. I only wish there was somewhere or someone that I could contact to get some satisfaction for my agony with this poor quality product! Yes, I am venting. I dont have another thousand dollars to spend for a new machine. Believe me, if there were to be a class action lawsuit for this lemon, I would be first to sign up!

Im guessing the company that makes Whirlpool appliances no longer make dependable appliances… bought home 2 yrs. ago. Bought Whirlpool over stove microwave and expensive side by side fridge. After 1 yr. microwave stopped heating. Now my fridge is no longer cooling. Have cleaned it underneath, did all a normal person would do. I replaced my microwave last year with a Maytag. I’m sure I will have to replace the fridge very soon. My stove is a Maytag. Dishwasher a Frigidaire... have had no problem. Just the Whirlpools… Will never buy another Whirlpool. Not just me, my niece bought a microwave. Her stopped heating after one year.

We purchased the Whirlpool Double Oven Range model GGG388LXS in April of 2011. The reason we purchased the oven is that we are empty nesters. We almost exclusively use the small top oven. We have streaks between the double glass on the bottom oven. We can not clean it. It is obviously a design flaw. I looked on this site to see if others have the same problem as it is too early to talk to customer service at Whirlpool. How have others fared with this obvious flaw?

I bought a Duet front load washer and dryer set in January 2009 from our local Lowes. Spin cycle noise progressively got louder over time to the point we contacted our locally owned service company to check it out in June 2011. Cause is defective shell and spin tub, total repair cost $750. This was about the original cost of the washer! I contacted Whirlpool via e-mail (wait time via their phone is outrageous), they wont do anything. Out of warranty. Up until now, Whirlpool has had a good name with me. Not anymore. I will never buy anything Whirlpool manufactured ever again. (Maytag, Kenmore, maybe more brands.)American companys insensitivity such as this is what gives some of American industry a bad name and drives consumers away to quality foreign brands made in Europe: German, Swiss, Italian, Swedish,etc.Im going to take a hard look at Bosch washers to replace this Whirlpool piece of junk.

Bought a dryer (wgd9050xw) 3 years ago. We bought a more expensive one than we had originally picked out. Every year its had to have a repair of same part. First year it was under warranty which tried to bill me so I had to dispute the charge. Charge was finally dropped. We just had it fixed again for third time in 3 years. Its a fire hazard because belt wears a pulley and basically melts it and gets belt hot. I just contacted Whirlpool and awaiting response.

This washer is 5 years old and the top is rusting out on the inner rim. I have city water that has been tested and found to be totally safe to use and drink. Neighbors using the same water and owning different brand washers have no rust problems. Does anyone else have the same problem with their Cabrio washer?

On 2-26-13 I received my new Whirlpool Refrigerator, Model WRF989SDAE, KSN 4191832, 28.6 cu ft, french door for a price of $2500.00. November 2014, refrigerator stopped working. Though it was not under warranty any longer, the repair company advised me that the problem was a warranty item and repaired it at no charge. This process took several hours of work by the repairman and two visits. He advised that this is an issue with the refrigerator and Whirlpool is aware. Now, May 2015, only 6 months later, ice is building up on the back wall of the freezer and the freezer is running constantly and very loud. Bringing in repair person, hopefully before it stops again. Appears to be related to the initial issue. I cannot trust this refrigerator and would highly advise everyone not to purchase a Whirlpool refrigerator. Refrigerator needs to be replaced, not repaired.

I love my Whirlpool LP Gas Range. Cooks great and bakes wonderful stuff. Also has a drawer under to hold pots and pans. Self Cleaning Oven. I do a lot of baking and I cook three meals a day. The burners are easy to clean off on top. I try and wipe spills up in the oven as much as possible, It has everything on it that I love, except it could have a plug in which would really nice.

Our Neptune washing machine is 15 yrs. old. Minimal problems, which I could fix myself. The door gasket needs constant attention to prevent mold. It is a front loader. I have replaced the gasket once. The belt transiently slips.

I bought Whirlpool Proton 3-door 18 months ago from a popular store at Chennai. I got a problem with cooling within 2 months. Service was availed and it got better. Same problem occurred again after 3 months of service, so I had it serviced again. Now the problem is its not working at intervals. I called the service and the person could not find any issues and says its working well. While it was pending resolution, the problem recurred and refrigeration is nil now. At the freezer, even after 8 hours, the water has not turned into ice and all food products have perished.

We contacted Whirlpool different times. I hate this piece of junk refrigerator. But Whirlpool never cared. My husband and I both did 20 years in the Navy active duty and reserves. 20 years each. Do you think we could have gotten some response other than a worthless sorry. To the Whirlpool CEO when you ever get some kind of compassion please us a real refrigerator that works and has some real room in it. I hate this thing and I hate not having an ice maker that works. A french doors refrigerator that really works would be good. Heres our address **. Please leave it on our front porch. Will be holding our breath. Thanks for your support.

I purchase a suite of Whirlpool Kitchen Appliances April 2017. My range is the slide in model. The knobs are on the front of the stove top. I 4 months in I saw that the paint behind the plastic panel where the knobs are was chipping. Also, the gasket in the oven had some loose threads so I finally decided to call the warranty. Whirlpool paid for the gasket to be replaced but Customer service said the chipping was cosmetic and that only covered for 30 days. I am so disappointed in this range and Whirlpool. My stove looks very used after 10 months. I followed the instructions on what to clean it with and how to clean so I know its not me. The paint chipping is crazy! How as consumers do we deal with this? This Range was a cost over $2000! and they give me touch-up paint!I purchased Whirlpool because I researched prior to purchasing my appliances. I thought I was buying Quality, this is not quality! At Christmas I had a pot of potatoes boil over and the element circle on the glass top cam off with cleaning. This too is not covered because its cosmetic. Ironically, my old glass top Whirlpool range did the same thing. That why I got a new one! I guess it still works. Who cares how it looks... RIGHT? Well, I WAS a good Whirlpool customer. Not anymore! Do not purchase Whirlpool glass top ranges unless you want it to look worn out after less than one year. I have tried to post pictures but this wont let me paste them!

Purchased a new Whirlpool built in microwave oven model WMH 310 17 AB-1 in July 1, 2013. As of February 2014, the glossy black finish on this microwave is dull where the finger push controls are and scratched up along the top of control panel and top front of door. We only use a wet cloth and towel or microfiber cloth to clean this microwave; nothing that would be abrasive so very disappointed in this product. It looks quite ugly for a new appliance. I did not anticipate how delicate the outside surface would be - never in over 30 years have I had this problem with another appliance, even stainless steel does not scratch like this.

Have, Quiet Partner II, Whirlpool dishwasher. Am 1 person, run only about 3 times a week and within 4 years now it will not even stay on. It will load sometimes with water then turn off. You can try forever and it will not stay on to run cycle. Waste of MONEY if this is how DELICATE they are and do not last.

It was in the house when we bought. I find location of knobs stove top, are too easily turned on. It is ok for now, but I am not a big fan of this stove. Builders buy a base grade appliances for profit in their spec homes to keep them. I will replace this one.

Its a piece of junk. The only time it will finish a wash and spin dry is when it is empty. Otherwise, it stops and lists an unbalanced error code. I opened up the service panels and found no broken hangers or clothes. There’s no way to bypass the system. I have read of similar issues and of course, its just out of warranty. I assumed the warranty was like other brands but it’s much shorter. What to do? Purchase a washer with dials and not a brain; it will last years. Note that the models without a brain cost far less.

Our burners broke down just 3 months after having purchased a new Whirlpool stove. Then a week later the oven broke also. I want my money back now. Do not purchase any Whirlpool products. Theyre garbage.

I bought a new Whirlpool electric range in the spring of 2008 and purchased the extended warranty from Leons. The oven worked fine for the first three & 1/2 years, but then the bottom element in the oven seemed to have stopped working. The top element would still come on, in an effort to keep the oven at temperature, but was not effective.I called in a repair. The technician showed up, turned the oven on, noted that the bottom element did not come on properly & replaced the motherboard in the control panel with no further diagnosis. The oven worked for approximately 9 months and then the problem recurred. I called in another warranty repair. This time when the technician showed up, he turned the oven on & told me he was going to order a new bottom element, which he installed about a week later, again, with no further diagnosis.Now, here we are again, one month off warranty and 6 mos since the last repair, and again, the bottom element in the oven is not working correctly. I reported the issue & my dissatisfaction to Whirlpool and was basically told, How sad, too bad - hardware components fail and theres nothing we are going to do about it. Seriously? This range is just barely 5 years old and has a history of repeated problems with the bake function - obviously, something is defective in this product.I can see it, if I had not had any problems until this point, but when the same issue keeps coming up & obviously has not been correctly diagnosed and repaired, I would think they would have enough integrity to offer some kind of help or solution. Given the history here, its highly unlikely that Im going to be willing to spend big bucks on another attempted repair that, in all likelihood, will be merely a short term band-aid, so Ill probably have to buy another new range - which I cant really afford right now. Trust me, it will not be a Whirlpool & it will not be from Leons.

My husband purchases Whirlpool washer years ago. Started acting up after 18 months. Wont spin, stays locked, clothes are soaking wet. Used troubleshooting website. Spent over $200.00 in repairs... including new board. Still doesnt work properly. Whirlpool customer service recommended buying a extended contract for over $300.00. I could have bought a $900.00 Maytag by now. Total disgusted with machine and customer service. Will never buy Whirlpool again and have told everyone by word of mouth and on facebook about this situation. DO NOT BUY WHIRLPOOL!

My elderly parents had everything they own destroyed in Hurricane Sandy. After rebuilding their home, the new Whirlpool washing machine was broken. Whirlpool refused to disconnect and remove the machine that was obviously broken before it arrived. This is something that no one should have to go through. It is appalling and bad business. Through the kindness of friends, we had several male friends help with the removal. Truly shocking, that this is how Whirlpool handled this situation.

We moved into a new home (brand new construction) in Dec 2018. The ice maker/water dispenser has never worked. Weve had 2 different repair people come a total of 5 times to no avail. Now have to deal with Whirlpool directly to deal with Warranty. Will Whirlpool offer a new fridge? No, they will send a replacement door. 8 months later and we still have a fridge that does not work. Not impressed with Whirlpool and extremely unsatisfied with the produce. Do not buy this brand.

Cleans average compared to previous dishwashers. Does not dry well even on high heat dry. Cycle takes about two hours and I have to run it during the day because it is too loud. The price was good, but I wish I would have bought a little higher grade.

We purchase the Whirlpool Gold Dishwasher GU2400XTPB7 with our new home. This dishwasher has a plastic tub. For some unknown reason the dishwasher started to leak, I checked every hose connection and could not find the leak until I noticed four small burn marks in the plastic tub underneath the heating element. It actually looks like someone took a cigarette to the plastic. One of the burns went through the plastic tub, and this is where the leak is. Note: at no time did any of our dishes touch the heating element.I called Whirlpool customer service and they said they would send a technician out for $81 and in addition I would be charged $19 for every 15 minutes of service. I had asked to speak to a supervisor and he recommended that a technician come to my house at my expense and all the supervisor could say was that he was sorry, which became even more frustrating. No remuneration was offered. I have had other issues with our Whirlpool washing machine (holes in clothes), gas range stove (ignitron issues), and fridge. l will never purchase any Whirlpool product again including Jenn-Air. I made this quite clear to the supervisor. Whirlpools products and customer service are inferior based on my experience with our four appliances. It would be great if they actually practiced what their mission statement suggests, because as a customer I truly feel defeated.

Bought the washer from HH Gregg for over $560 12/2012. Turned on power 4/2014 and just heard clicking noises then nothing. Had to get technician. Paid for $75 service charge and waiting for cost of labor and part for the lid lock/latch assembly. I see a lot of complaints with this new machine. I bought a new one BECAUSE I did not want any problems with repairs. Whirlpool is ripping off the consumer passing out this piece of discombobulated metal, wires and electronics. An appliance like this should last AT LEAST 7 years without a problem. I wish there was a class action lawsuit and will be waiting to the day it surely comes.

I bought my new ceramic top electric range/oven with convection, and the aqua-lift cleaning system in spring 2017. The aqualift cleaning function is a joke, so be prepared to be down on your hands and knees scrubbing. Im careful, and Ive not spilled anything yet, but the oven still gets splatters from roasting meats, etc. Id hate to see what Ill have to deal with when I actually let something spill. Today, as I was down on my hands and knees trying to clean it, I noticed that the enamel is chipping off where the oven racks slide in. Great. I have never had an oven where the enamel came off, much less within a year. I am struggling with heart failure, and I am not up to fighting with Whirlpool.

Whirlpool Hot Water Tank Thermocouple - This is the third thermocouple we have had to replace on this hot water tank in the last six years. Granted the part isnt that expensive, but the service call and replacement have cost us dearly. This is faulty tank and Whirlpool needs to recall this tank and replace them with new tanks. The price of this original tank and replacing this thermocouple three times has cost us over $800.00 total. I am not sure angry is the right word to describe our dissatisfaction with Whirlpool.

Started researching online about a week ago because my dryer was making an awful noise. Found out that the new idler pulley system the company used in my Whirlpool cabrio washer & dryer model (WED5500XW0) was so ineffective that they have since started replacing it with the old part #691366 they used to use. Also I am having a problem with my washer not spinning all of the water out of the clothes. Found out that this is a common problem with this model (WTW5500XW0).Had a certified repairman out to replace the dryer idler pulley system. He also calibrated the washer to see if that may help (it did not). The repairman said that some of the Whirlpool washers had been recalled and he had actually replaced some control panels and that seemed to work. He suggested that I contact Whirlpool. So I contacted Whirlpool, thinking that they obviously knew that there have been many problems with these machines (idler pulley part being discontinued & and recall on SOME models), and thought they would be more than willing to rectify this problem. Well think again! The two young ladies that I spoke with sounded like robots, Unfortunately, you are not within your 1 year manufacturers warranty so there would be nothing we could do at this time. Although I must tell you, the second young lady I spoke with did offer to sell me a new washer at a deep discounted price of $386 (which is only $86 more than fixing the washer). I think everyone who has a problem should contact Whirlpool and express this dissatisfaction. And if you are shopping for a washer and dryer, stay away from Whirlpool because their customer service is disheartening.

Refrigerator model WRF560SMYH purchased 22 months ago will not defrost automatically. When ice builds up on the back of the bottom mounted freezer, it creates a terrible noise. Only quiets when we manually defrost the ice with a hair dryer!! 4 service calls from the warranty company has failed to solve the problem.

Purchased our stainless steel Whirlpool Gold range hood microwave oven in January 2011. By August, there were problems. It was noisy. It would occasionally shut off for no apparent reason and eventually in August of that same year, it completely stopped heating. The magnetron was replaced at no charge because it was still under warranty. The microwave has continued to run very loudly, vibrate a lot and is still prone to random shutoffs. Now a little over 2 years later, it has now stopped heating again...I am assuming another bad magnetron. How is that possible? Our last microwave lasted for over 10 years! In fact we got rid of it when it was still working fine so we could get this one for over the range instead of on our countertop. So now I have a Whirlpool paper weight for which I originally paid $485. When I called Whirlpool, I was informed a service call would be $130.00 PLUS any necessary parts and labor costs OR I could purchase the repair plus 1-yr extended warranty for $289.95. Upon requesting to speak to a supervisor, I was informed that there were no flags in the system indicating any problems with this line of microwaves. I further inquired on how they are aware of problems... Essentially a phone call warrants little proof of any problem. A service tech would have to actually go out and witness that there is a problem for it to be noted. So, for those of us that simply decide to turn our back on the product and buy a new microwave, it would go undocumented by their company. My top-of-the-line microwave is less than 3 years old and has broken down again. Doesnt common sense tell you that there is a problem with the quality? I know Whirlpool has been around for 100+ years and I really want to like them, but if they dont support the consumers that purchased their products, I can no longer do the same for them.

Purchased this Whirlpool Duet washer WFW920ww00 in 2011. 6 service calls while under 1 year warranty. The mother board was replaced..... after I smelled smoke and burning. Had trouble draining.... error codes F9E2 and F9E1 and SD (suds) and low flow were the usual. At times took 4-6 runs to get it through to point where I could open door. Often need to unplug for 20 minutes in order for it to progress. Clothes would not ring out... or be floating in water. Lately had to run on medium spin just to get it to work at all. The odor/smell was horrible and the rubber ring was black with mold after the 1st year. Completely stopped working this week, no power to panel. The repair shop said to not bother.... he has had customers replace 2 or 3 major parts in these and still keep getting the annoying error codes and difficulty making it through a complete wash. Moving on and buying something else.

We bought a new house and the choice given to us was Whirlpool. After the first year in the house we had a $300 repair. The control panel inside the fridge went. Pretty poor performance.

Cabrio Washer WTW660SW2 - For 2 years I have been getting f1. When I talked to Whirlpool they said they were not aware of this problem. Now I have to pay to fix it. Looked online thousands are having the same problem.

When I purchased my Whirlpool Cabrio washer and dry, I was told by the sales associate that this was the top of the line. I paid a higher price for what I thought was quality only to find out that this washing machine (WTW6600SW2) Serial number CU2973872 is in fact poor quality, made of components that are cheap, unreliable and made to last only as long as the initial warranty. Prior to buying Whirlpool, I owned Kenmore and had a washer and dry that raised four kids, now I own a Top of the line Cabrio that cant wash the clothes of two adults. I think it is funny that two days after the washer started sounding like a jet plane taking off during the spin cycle, I received your sign up for an extended warranty letter. Then I take the washer apart to locate the trouble and find it is a single bearing on the top of the drive shaft, but can I buy the bearing and replace it? No, I have to buy the entire outer tub and drive shaft. So a $10.00 bearing will now cost me $200.00. I am sure that helps your profit margins considering all you have to do is a search for Cabrio problems to find 350,000 hits, or to ask a professional technician and receive the reply that they are replacing 2-3 of these tub and drive shafts per week. I would recommend that Whirlpool tell its shareholders that you have compromised customer satisfaction to line their pockets with profits. If that was your intent then you have succeeded, however you need to also tell them to sell their shares now as you will have no return customers. Most corporations have core values that deal with safety first and then always followed by quality. I can say with confidence that your quality can be nowhere near the top five with this many problems with your top of the line product.

This product is unsafe and should be recalled. It has aluminium wires that connect the unit to the 220 Vol Power source. Aluminium and copper wire dont mix. I took a shower and was getting ready to leave for the day when I went into my garage to smell burning plastic and wires. I traced it to the hot water heater and discovered the wires in the Energy Smart were melted and burned. I checked with Two Electricians who told me that the wires in the unit can not handle the high heat and melt. If you have one get rid of it. Had I left for the day I would have lost my home, cars and pets. If anyone would like to see this unit I still have it and photos.

My fridge is a French door-type with two doors on top and a pull-out freezer with a ton of room! There's water at the door and an amazing ice maker inside the freezer. Two drawers for veggies, fruit, meats/chicken. And a retractable shelf to make room for larger, taller items.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

Weeks ago, we received a new refrigerator from Whirlpool. Never really got down to temp. They replaced the compressor and still does not work. You would think a company like Whirlpool would replace it. That is a joke. They want to try and repair it again, another compressor? Now I have thrown out the food in it and feel like Whirlpool could care less. DO YOURSELF A FAVOR< DONT BUY ANYTHING MADE BY THIS COMPANY OR THEIR OFFSHOOTS.

I’ve had this washer since October 2018. Worst purchase ever. It does not clean the clothes nor does it put enough water in it. I’ve tried the deep water option too and it’s for sure still not enough. I don’t understand how they even thought that this was perfectly fine to sell. If I could’ve taken it back a month after having it, I for sure would. And no one will buy it because they’ve read reviews of how it’s terrible. I wasted $900 on this washer. I have the dryer also which works amazing. The washer just sucks something terrible. My husbands military uniforms always look dirty and a lot of the clothes aren’t ever wet. I’ve finally seen a picture of how you’re supposed to have clothes in there. Why in the world would you only allow barely a layer of clothes at the very bottom to be cleaned by the agitator? Why would you have this huge drum only to put not even a load in there? This was such a waste Whirlpool and I’m glad I’m not the only person who has the same issue. I will never purchase another Whirlpool washer, it’s upsetting I can’t currently get rid of this crap washer I have now.

I purchased a new gas water heater from Lowes and paid a plumber to install it. I have been having problems with it staying lit. Once I noticed the issue, I notified my plumber and the plumber was aware of this on-going issue with these water heaters. The plumber told me to call Whirlpool and have them send me a new thermocouple. Ive been putting it off until now, but realized today over the phone with Whirlpool Customer Service that the problem is with the vent. The manual that came with the water heater has a horizontal venting installation, yet Whirlpool claims that it should be vented through to the roof and they sent me, via email, the correct manual. When I asked Whirlpool how the plumber was supposed to know, she said that he should have known that it was not the correct manual (even though there is no model number written anywhere in the instructions manual) and that we should call to make sure that we have the right manual before installing my next product. So, I need to double check every purchase I make! Or is this only with Whirlpool products? After speaking with two different Whirlpool reps, I have concluded that I need to purchase a new water heater, but believe me, it will not be another Whirlpool!

We recently purchased a refrigerator from a reputable local appliance store after months of shopping and comparing and research. As an opinion, Whirlpool seemed to set the standard for a quality appliance. Unfortunately, we failed miserably by buying this side-by-side fridge. Two unsolvable problems. First, the cold side door is extremely difficult to open. Ive tried ALL gasket lube methods and failed. Second, the stainless steel used on the front of the machine is obviously low grade that accepts magnets and is almost impossible to clean weekly without streaking. They were kind enough to provide us with their special cleaner {free} but it takes about an hour and a half to use for moderate success.The lady on the help desk listened but seemed rather cold and uninterested in the problems. At this point, we would be willing to pay the extra and go to a Kitchen Aid instead. Our advise is beware of these types of issues and get some kind of guarantee from your store when buying a WHIRLPOOL refrigerator. This is simply terrible.

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

We bought the Whirlpool refrigerator from Home Depot. The ice maker does not work. We get 2 cups of ice a day. Home Depot Told us we should get 8 to 10 pounds of ice a day. We call a repair service and they said we should get 2 pounds of ice a day. Still getting 2 cups a day. Call again and now they said we should get 64 cube of ice a day. So now Home Depot has us calling Whirlpool instead of them. Now we will have another repair company coming out. Waiting to see what they have to say.Very disappointed with Whirlpool for not backing their refrigerator. And don’t buy from Home Depot. You can’t return if you buy it. And I have a warranty on it and they have a lemon law 3 repair calls for the same thing and they will take it back. Not true. I will be calling once a week for 5 years until they get me some ice. They don’t deserve a 1 star.

If you are in the market for a new refrigerator, STAY AWAY from Whirlpool Top Freezer models. Mine just failed after only 5 years and Whirlpool will NOT do a thing about it, except ask, Did you buy the extended warranty? The compressor in my refrig was made in Mexico by a company called Embraco. I used to work for Whirlpool and these compressors were garbage then, and I guess still are, in my opinion.The 5 year sealed system warranty was removed from these refrig years ago and I can only assume this is why. If you want the 5 year SS warranty, buy a side by side or French door model. Just be sure it doesnt have an Embraco compressor on it! And while I am not a believer in them, planned obsolescence dictates you probably should buy the extended warranty/service plan for such a purchase. Dont rely on positive past experience, even for a company like Whirlpool. Their gold ring of promise emblem is very tarnished for me now.

Great washing machine. I have been using for over 2 years and this washing machine has NEVER failed me. Clothes from extreme filth to sensitive material always come out clean, not damage, and smelling great. I would highly recommend Whirlpool washing and drying machines to anyone!!

I have had a Whirlpool hot water tank now for about 7 years and all I have had out of it is trouble. It wasnt even a year old and I was putting a thermocouple in it a few months later I put another one in it. All I do is put thermocouples in it. I have saved the old ones. This heater is a piece of junk and I am the one whos paying the price for it. I just put a thermocouple in it on January 9, 2012 and I am putting another one in it on January 15, 2012. I have replaced all parts and it still does it. They are going to buy me a new one someday. I’m tired of this. This should not be happening. They are ripping people off. If the pilot light does not light, you have to replace the thermocouple in it.

Whirlpool Cabrio drain problem - I never had a washing machine that lets so much through to the drain pump. I replaced pump three times already. First of all, if you put anything with buttons in this machine, you can kiss it goodbye. This machine destroys clothes then lets buttons and coins and whatever through to destroy the fins on the discharge pump. When is the BBB going to do something about this consumer ripoff?

Whirlpool WRT351SFYW 21.1 Cu. Ft. White Top Freezer Refrigerator - Energy... puts out a very irritating high pitch noise, unlike my previous Whirlpool fridge. The old one was perfectly quiet. I believe Whirlpool is going downhill in every way. WP is buying refrigerators from 3rd world countries and slapping the name on them. The delivery people were very rude with me when I was unable to give them a tip, even though I had to supply my truck to shuttle the fridge up to my house and help them unload it. I also had to go and find them when they would not follow my directions to my house. So, they kept the wrench I loaned them; they did not have their own tools for the installation. And they refused to return it when I asked them to do so. Denvers Customer Service refused to respond in any way to my requests for information or complaints about the noise and delivery. Finally, their head office contacted me a month or two later, and the customer service person had initiated the discussion in argumentative attitude despite my saying I did not care anymore, I gave up on them and dont expect anything from Whirlpool anymore. While she told me that there are standard levels of acceptable noise that come from their refrigerator, while, she refused to acknowledge that they are not my standards, and I am the customer, besides, I had an older Whirlpool fridge that did not make any noise. I am sorry trusted WP, when I tried to upgrade the old fridge - it was an expensive downgrade! Buy LG or Amana - wished I did!

I purchased a new Whirlpool Cabrio washer/dryer set 2 1/2 years ago (Jan. 2009). I have 4 kids and do lots of laundry. This is THE WORST appliance, namely washer, I have ever owned! I so wish I had researched this product more. I ditto everything that has been said about this washer. It tore up so many items of clothing, I lost count and does a horrible job of getting stains out. I contacted Whirlpool on several occasions only to be told that they would send a technician out to see if there was something wrong. The technician would report that the washer was working properly and Whirlpool would then tell me, sorry, we cant do anything about it. I asked them if a washer was supposed to clean your clothes and unravel them? Yes, it is supposed to clean them. Well, its not doing that. No, it is not supposed to unravel and destroy them but well, it IS doing that! Therefore, the washer is not working properly. Just because a technician can not physically find something wrong with it, doesnt mean it is a poor functioning washer. This company should better learn very soon that you must stand behind the QUALITY of your products or you will soon be out of business. I will never purchase Whirlpool products ever again nor would I recommend it to anyone!

I purchased the Whirlpool Cabrio washer and dryer about 5 years ago. I wanted to pay for a good pair to last a long time for the money. We have had a repair man out twice for the washer. They ended up replacing the computer board. It worked fine for a few years. Now, it keeps getting the unbalanced error code for almost every load of clothes that we start. Sometimes, it takes 20-30 minutes of rearranging the clothes to get it to finally work. I have had to manually set it to finish the loads on a number of occasions. It is so time consuming to do laundry due to having to play with the clothes to get the loads to finish. Plus, I dont know how many times it has woken up my grandkids because of the loud thumping noise it makes when it gets unbalanced. I have never had a washer do this. I would expect when you pay big bucks for an appliance that it should last a long long time. One usually gets what they pay for. I should have bought a cheaper pair. Then, they probably would have lasted 15 to 20 years.

They have sent three specialists to look and assess the Whirlpool washer and dryer that I have. Both stated that the washer does not function correctly; the last repair man stated that he had seen many like this and they have a history of unreliability. I would like my money back, not a repair, as they do not even use just cold, but a mixture of both hot and cold. I had bought them specifically because I thought they only used cold, which was stated by Whirlpool. This is wrong advertising. I would like my money back. I still have the receipt and I am seriously unhappy with the washer and dryer, period.Since I cannot use the machine, which I had bought for $1600.00, the washer and dryer is now sitting in my basement. While whirlpool is saying that they wont take back the washer and dryer even thought it has a warranty. I had paid it in cash and I do not see why I should be forced to keep a broken washer and dryer set. I will contact my lawyer to consult this issue with Whirlpool.

We bought this Cabrio washer WTW6400SW2 several years ago. Immediately after having it delivered and installed, it started displaying an F1 fault code. The main control board was replaced under warranty. It happened again within six months. Another board was replaced. That board lasted another six months. The warranty was up by then, so I used the machine by hovering over it and restarting it every time it failed. After two years of this piece of junk, we put it in storage while we worked on the road. It was brought out on 10/01/11. I called a repairman (who came on 10/04/11) to come replace the board again. He told me that the last two times it had been replaced with the same defective board, that Whirlpool had never fixed the problem. He claimed he had the new improved board, which he replaced for about $350. Two days ago (361 days later), it went bad again. The same repair company came back and said it was the board again. I just tried chatting with a person working on the Whirlpool website. They (of course) said they would do nothing about the washer. They do not stand behind their product, obviously. Does anyone know of a class action lawsuit over these washers? It is a ridiculous amount of money to spend for a product that does not work. This is just wrong!

We built a new home at the beach to enjoy our retirement and the builder installed new Whirlpool appliances. As far as we are concerned this was the BIGGEST WASTE OF MONEY WE HAD. Our appliances were under warranty for 1 year as usual and after 14 months things began to break. The latest is the ice maker in the French door fridge. After finding the diagnostics test online I ran the test and determined that the whole ice maker needs replaced. This ridiculous since the fridge is only a little over a year old. We even upgraded the fridge to avoid any problems. After talking to the people in our neighborhood we have come to find out that most people here have had trouble with whirlpool appliances.. I am ready to send these to the junkyard and replace them with a reputable brand (LG) that we owned before and were very happy with.. I dont understand if there is all these problems with Whirlpool products why the technical team doesnt fix the problem... Get parts from the USA NOT CHINA!!! My neighbor just told me he had the repairman at his house 7 times to fix his fridge and finally got a new one. Just got tired of the hassle and expense....

Whirlpool 29 cu ft French Door Refrigerator WRF989SDAM - We purchased this refrigerator September 2013 for our new home. We moved in November 18, 2013. The refrigerator made a very loud buzzing/humming noise from the beginning and did not make enough ice. The shop we bought it from came on 2 occasions to work on the ice maker and finally totally replaced it. Then the rack on the bottom of the left door fell out and contained glass jars of pickled vegetables. They broke and made a big mess and etched our travertine tile floor. We called the shop and they sent their son out who put the rack in with duct tape which of course did not work so we took it out and put it in the cabinet. We had to pay to have the tile polished to remove the etching. On the weekend of November 15, 2014 the humming noise was so loud that we called the repair person again and they came out on November 17, 2014. At first they thought it was a fan motor but the freezer started making a loud noise and the owner came and said the compressor was going out. Our food was beginning to thaw and we asked if they could at least loan us a refrigerator to use. They brought us an old small fridge which was put in the garage. We took all our food out there. They came November 25 and picked up the fridge to be repaired. We had been told the warranty was out but after calling your company they were told Whirlpool would cover parts and labor. Today is Thanksgiving Day and we can not cook a big meal due to the small fridge and freezer and we are buying bags of ice every day. We have family visiting and must go out for dinner. We have no idea of when our refrigerator will be returned to us. This has been an expensive and disappointing experience. I would never recommend your refrigerator to anyone due to this experience. I really feel we should have been offered a new refrigerator at a discount. We bought all our appliances from Dons Appliances in Okeechobee, FL 34974 and they are all Whirlpool. This refrigerator cost $2299 and our total order was $9,642.84. We would appreciate a response from your company.

We purchased a top loader Whirlpool Cabrio Platinum Washer and within a few short months noticed a mildew-like smell emanating from it. This is DESPITE the fact that we leave the top up the entire time that the machine is not in use, we use hydrogen peroxide and ammonia in our loads of laundry in order to kill any mold present and my husband painstakingly hand dries the interior of the drum after each load of laundry. He also puts hydrogen peroxide in the fabric softener dispenser in an effort to kill the mold/mildew. None of this has helped to mitigate the ongoing mildew/mold odor. We have run across other online reviews which suggest that the Cabrio does not fully drain the water in the washer leading to the potential for the development of mold and mildew. This is very upsetting as we paid a lot of money for the Cabrio and had high hopes for it.

We purchased our new home in February of 2012 and found a good deal on a 6 appliance package from a local dealer (not box store). In these four years, had to replace igniter in gas range oven. Weve had 3 repair visits for the fridge, dead ice-maker, temperature imbalance freezing vegetables, meat drawer constantly falling off tracks, door shelf rails fall off and all shelf contents fall to floor. Dishwasher rinse dispenser has never functioned, never empties. Technician claims it is working as designed. Washing machine - 3 separate service calls. We finally decided to buy a different brand last year. Only the dryer and microwave have have performed as expected with no service calls. The package deal saved us about $500 but in just 4 years we have spent over $1000 (including $400 to buy a new washing machine). VERY disappointed in this brand.

Machine wont go through the whole wash cycle., Wash, Rinse, Spin. It stops and shows an error message and then I have to keep rearranging contents, over and over. This is worse if you try to wash a small load.

I have used my Maytag washing machine weekly for the last 11 years... Never a problem. Just a well made, basic machine to wash clothes thoroughly. It does not have all the bells and whistles some of the newer models have, but it is a washing machine, not a video game.

First F1 symbol on washer took 6 months to resolve. All we needed was new motherboard and couldnt mail it to us even though we could replace. It had to be an authorized person. Well we had one and they never put him in the system. Finally got that taken care of, 6 months of having to press pause and restart 5 times just to do one load. Arrrrrggggghhhh! Now water leaking out the bottom. Called again, on hold, then on hold again to be transferred to tech support. Yeah, right. No tech support. Talked to management, they could care less about us even though we have other products from them. Dont buy, they are lemons. We had ropes for 15 years and lasted through everything. Thanks Whirlpool, heres to losing a customer!!!!

I am a mother of 4 children and 3 grandkids, I love cooking and baking. Before I can post a review on a product or appliance I like to wait and give it enough use to test it. About 2 years ago I purchase a Whirlpool range. I trust the Whirlpool brand because is durable, easy to maintain and simple to operate. After owning my first Whirlpool refrigerator for over 15 years, I am happy to post my review on my almost 3 years old Whirlpool gas stove and oven. I am a satisfied and proud customer of Whirlpool!

Whirlpool Cabrio Washer WTW7800XW is 13/14 months old (1 or 2 months out of standard warranty). We use it 3 to 4 times a week. The lid hinge developed a crack 2 or 3 months ago. Last week, it failed completely making the washer unusable. Investigations show that a new lid is around $250 plus tax and service call (approx. $500 complete). On contacting Customer Service, they continued to say monotonously out of warranty even though it is obvious to even a layman that this hinge/lid is not fit for the job and the manufacturing material has failed. They kept reeling off all sorts of protocols but would not send any of them as a copy. This is the worst service I have had from any company. The service is despicable and they should be ignored and banned from every consumer list. I appreciate that it is out of warranty, but the runaround I am getting seems to me that they expect their product to fail after the warranty expires and they are not surprised at all by catastrophic failures so soon.

Buyers beware! I have had the Cabrio top loader washing machine for less than 18 months and it is already giving me problems. During the wash cycle, it sounds as though the gears are grinding to the point it wakes my family up two floors up! The spin cycle is a joke. The washer sounds as though it is going to spin off into another room! When I called Whirlpool, they told me to shut the circuit breaker. That might reset the computer. No go which I figured as much. I have had washers that lasted 10 plus years with no problems. It is not worth your time or your money. Never again, Whirlpool!

It seems the quality issue of the LED of the washer Whirlpool Cabrio. It was broken from the screw part of the glass and the plastic/alloy and the glass. They would charge me $416 to replace the LED but I rejected and was still required to pay $85 for labor fee. I called the company and they didnt admit that was a quality issue but I just found many consumers had the same problem. If someone would like to have a lawsuit, please contact me and I will join.

Our Fridge has totally died at 16 months. The warranty was only one year. The customer service folks said online they might help, but we did not receive any response after two emails sending the make and model and serial number. An expensive fridge should last longer than this!

We moved into a new house in May 2013 and there was a new Whirlpool Gas Range installed. We have experienced an intermittent problem where the oven will not ignite since day one. We have reported it to Whirlpool and different technicians have attempted to repair it but it is still faulty. When the standard warranty ran out I purchased the Extended Warranty Protection from Whirlpool but it is WORTHLESS and they cannot fix it! The last technician from Philips Appliance in San Diego was terrible. He said he would order a new control board but never did and he closed the case without telling us.When I called Whirlpool to check on the status of the problem I was told that they will not look at or change parts for intermittent problems so what did I pay the extended warranty money for? When the oven does not ignite there is a smell of gas and we are now concerned that it may be dangerous so we are about to dump this useless Whirlpool gas range to a purchase a LG model! Bottom line is NEVER BUY Whirlpool and NEVER WASTE your money on a Whirlpool Extended Warranty Plan!

Bought a brand new front loader washing machine and the 1st, 2nd & 3rd year has to call for service for the same problem! Sent one repair guy to the house and banged on my machine the whole time because he was frustrated and had to report because he made my wife nervous. Never again Whirlpool!

Everything I buy from this company breaks all the time. I purchased these brands hoping they were good but apparently not. Always have to get them serviced. Lately they did an exchange on my fridge. Hope it helps because after thousands of dollars of food in the garbage it better work. And the washer thought, Oh Im paying more. It will be good. At this point will cost me less to buy from another company. Buyers beware. Cause the company cant do nothing good for me so dont buy from them.

Whirlpool Gold Refrigerator Control Panel Failure - This French door refrigerator with freezer on the bottom was purchased new in November 2008. This August, the refrigerator stopped cooling. I contacted a reputable local appliance company who diagnosed the motherboard was not functioning on the appliance. They ordered a new one from Whirlpool and replaced it. Forty-five days later, the replacement motherboard stopped functioning. When I contacted Whirlpool directly to inform them what was happening, they continually stated that the appliance company was not part of Whirlpools approved appliance technicians, and offered no assistance in guaranteeing the problem will not continue to happen. I am extremely disappointed with Whirlpools customer service and unwillingness to guarantee their products. A 3 year old refrigerator should not stop working.

I purchased a Whirlpool fridge (model GX2SHBXVQOO) on November 27, 2010 and it leaks water on my floor. I have to keep a towel there or it runs all over. I also purchased a Whirlpool range (model YGFE461LVQ) and the convection fan went on it a month after we bought it. The manufactures warranty does not allow repair people to travel any further than 100 km to repair, something that we had to take the stove in to be repaired. We got the stove back the same day and brought it home. Low and behold, after a short period of time it started to rattle again and got steadily worse. Also, now my one burner on high does not stay on high; it keeps going out then coming back on.I have called the place we purchased these pieces of junk from and they said there is nothing they can do. I also sent e-mails to Whirlpool and they said they will look into it and get back to me. That was months ago. I called Whirlpool and was basically told that there was nothing they can do, that I was to call the repairman. Never, never, ever buy a Whirlpool product.

So, I have a house full of relatives from out of town staying over and as luck would have it, my Whirlpool water heater (model # BFG1F4033T3NOV) which I had installed 15 months ago, decided to stop working. The pilot light went out and would not stay lit no matter how long I held the red restart button. I called Whirlpool customer service and was informed straight away that their computer system was down and they wouldnt be able to order parts if I needed them (great start right?). I explained to the woman on the phone what my issue was and also told her that after searching online, Ive found that this is a common failure with these hot water heaters that Lowes sells where the thermal couple is defective and needs to be replaced. She began to inform me that before any parts was ordered (which she couldnt do because the computers were down), I would have to clean the vent openings on the bottom of the HW heater. No big deal. Then, Id have to have my gas line pressure verified by my gas company (what?). If both were found to be fine, Id have to confirm that my flue is at least three feet above my roof line before they would send me parts to repair my unit. This is about where I lost my mind.I run the RMA/Customer service department in my company and if anyone has issues with our products, we ship first and ask questions later. How can a company with known defective products give their customers the runaround and basically tell them that they are screwed until they can take off time from work for a gas co. to come to their home and will also have to have flue replaced before theyll warranty their product?! Whirlpool should be ashamed of themselves and Lowes should distance themselves from such a crappy company with substandard products and shoddy warranty practices. Ill never buy another Whirlpool product as long as I live and will warn anyone away from this company.

Purchased a new French door Whirlpool fridge May. It replaced a Whirlpool that was here when we purchased the home. Ten days after purchase the fridge went to 21 degrees and began freezing over food and drinks. Yesterday a tech replaced parts to repair the fridge. Today the fridge is once again at 21 degrees and freezing food and drinks. We live in a relatively rural area. Tech cant come back until six days from now. Very disappointed. Wish we considered another brand.

We bought the microwave new after the 2011 flood where we had lost everything in Tennessee. I wanted to get Whirlpool appliances in the kitchen so all appliances were replaced. We bought a Whirlpool model WMH1163XVU-1 microwave; the unit will run but doesnt heat. I also called Whirlpool and with no regard to customer service at all even with all the complaints... This saddens me because I will never buy a Whirlpool appliance again and my grandparents only believed in them... With all the complaints, the attorney generals office should do something for the people.

We purchased a new home in July of 2011 and we paid extra for the upgraded appliance package, which included a Whirlpool Microwave/Convection Hood Combination unit. We have Model # GH7208XRS3. We use the microwave a few times a week and only used the home 6 months each year during 2012, 2013 and 2014, for a total of approximately 18 months. From the very beginning, we had trouble with the microwave control panel turning itself on and the electronics going through various timing and programming functions independent of any human operator.During the combined two-year warranty period from July 2011 July 2013 (the Manufacturers Warranty lasted one year and the Developers extended Warranty lasted an additional year) we had 5 service calls on the same issue. The Authorized Repair Center repairman called the Whirlpool Tech Line while he was in our home and was told that there was a flaw in the design of this model. They replaced the door and then when it acted up again, they replaced the control panel. In Nov. 2012, after the repairman told us the door needed to be replaced again, we asked for a new appliance since we had the same issue repeatedly and they had already tried to fix it by replacing the door and it was still under warranty. We were told that Whirlpool would not replace the appliance until they had tried to fix it three times and we needed to get a new door again. We were told that because it was the same issue repeatedly, we would get a replacement if it still went bad after the warranty was up. So we had the door replaced again, which did not fix the problem.In late 2014, we again had the same issue with the control panel and made a call to Whirlpools Customer Experience Center. At that time, we were told that the warranty was no longer in effect and Whirlpool would do nothing to fix the issue. Even though it was the same issue that they had attempted and failed to fix while under warranty, the company would no longer stand behind the promise of customer satisfaction and told us they will not replace a 3-year-old microwave. When I asked the Customer Service Rep to speak to a Manager to escalate the issue, I was transferred to the Tennessee Office. When I got the same repeated run-around from the Supervisor, Melissa, I asked that Customer Service Supervisor to let me speak to a Manager and she told me she could not give me the name of anyone else to speak with and hung up on me.I am writing to you to express my extreme disappointment in Whirlpool and the products reliability, the way the company has handled fixing the problem and especially in the conduct of the Customer Service department. Whirlpool gave us nothing but a run-around for the years the warranty was in effect, knowing that this model has a design flaw and trying to do band-aid fixes until the warranty ran out. We were told that our only option now is to pay to have the same problem fixed a fourth time or purchase a new microwave.Whirlpool has trained their Customer Service people to be polite but ineffective and obstructionist on the phone and then hang up on the customer when they cannot resolve the customers issue. I believe that Whirlpool should be committed to customer satisfaction and making sure that their products work as intended and fix the problem that was reported while under warranty, even if it no longer in warranty. Whirlpool should be as disappointed as I am that after three attempts the problem is still not fixed and should be committed to customer satisfaction enough to replace the appliance after three failed attempts.

I have a Whirlpool Cabrio washer. It was great for almost year. After that it has been nothing but trouble. The body of the washer has rust coming through the paint and large areas that is so rusted that the paint has chipped off completely. A washer is expected to deal with water and not rust through the body. I have a 10-year old Ford truck without a speck of rust. Dont they undercoat? The circuit board has had to be replaced because of rust. I have to take several Q-tips and go under the cover to remove all the rust if I dont it gets rust stains on my clothes, which is impossible to remove. The customer service is non existent. They have left me on the line for over 40 minutes. I hang on only because it would be another hour or so of my time to get someone to answer. I was without a washer for a month while waiting for parts. Why dont they have parts for their products? I had to slop my way too dirty laundry mats 3 times a week as I do 2 to 3 loads a day.My washer is downstairs and stops and gives me the unbalanced message even when its not, running up and down the stairs several times to complete one load. I also get the F51 message for no perceivable reason. The extra rinse button only works 1/2 the time. This was an expensive washer ($1,000.00) and I feel that I deserve my money back. They are knowingly making an inferior product.

The machine is two years old. It cost over $1,000 to buy. From the beginning, we have had mold issues with the machine. The entire house fills with the smell of rotten eggs every time we use it. The machine is used daily so it doesnt sit for long periods. Despite all the complaints online about their machines, Whirlpool refused to acknowledge that there is a design problem with the machine. They refused to make any repairs or buy the machine back and their only suggestion was to buy more chemicals from them to use to clean the machine. We have done this in the past to no avail. Oh, they did offer to send out a service company but on my dime. Whirlpool needs to be sued and I only wish that someone would start a class action suit against them. It really stinks when you try and do the right thing and buy American only to have the company not give a crap about their customers or the fact that their product is garbage. About 10 years ago, I had a Maytag front loader washing machine with the same problem. Maytag bought the machine back on a pro-rated basis, no problem, no question. Of course, Maytag is now owned by Whirlpool. Too bad they didnt adopt Maytags customer service policy. I cant wait for them to go out of business - something they deserve.

From the day I bought the refrigerator the icemaker has not worked. I have had a estimation of service calls (8) and nobody seems to be able to fix it. Whirlpool mailed me a new icemaker and still the exact problem; water and ice works but the unit still will not cube or crush ice; which by the way is the reason I bought a new refrigerator. My thoughts are I bought a lemon and the entire fridge needs to be replaced.

As many others have posted - the Cabrio washer is awful. Cycle time > 1 hr. Clothes not clean and caked in soap even with extra rinse. Phone Whirlpool and found they dont care. All theyd say is its government regulation fault but for $100 they could send a technician to ensure it is working as designed. To environmental reasons for the new design, seems to me it missed the mark. Longer cycles, extra washes, extra rinses... All I can say is - Unbelievable!!!

We bought all new Whirlpool kitchen appliances in February of 2017. The French Door Refridgerator MRF993FIFM we purchased was a large side by side with a water/ice dispenser and freezer on the bottom. The concept of it is great, as it is very roomy. The problem is with the product quality and usability. We are a family of four with the youngest being twelve. We do not have to worry about rough little hands anymore. That being said there is a crack in the back of the plastic casing of one shelf, a crack in the freezer door, the seal doesnt connect on the dispenser side door, the slide out shelf in the freezer doesnt stay on its rollers and the main ice maker stopped working (which never worked properly either).Also, and this is what bothers me the most, the glass on one of the shelves is sealed down so it cannot be cleaned under. But there is a small slit going all the way around that separates it from the plastic. Food is still seeping underneath and creating mold with no way to clean underneath! This was not an inexpensive refrigerator and we were not prepared to have these kinds of problems after a year. We are very unhappy with the quality of this product.

On 12/27/2013 I bought a Whirlpool hot water heater from Lowes Model NU50T122-403. On 12-13-2015 the pilot went out. When I called tech support on 12-14-2015 they gave number what were call centers or person who returned the calls. So I called a local plumber that I used before. He came out and told me that had to replace the pilot. On the 16th 2015 of Dec. that did not work and told us the heater needed to be replaced. The replacement will happen today I hope with little to no help from Whirlpool. I would advise you to do your homework before you buy a Whirlpool hot water heater.

I would not recommend this product at all, nor would I recommend the Whirlpool Company. This washer was over $1200.00. Within two weeks of purchase, I had to call a service repair company as I was immediately having issues with the washer not draining. Being a front loader, this machine required using the appropriate HE detergent. I followed the instructions, used the appropriate products and had nothing but continuous problems. It is a (lemon), and very frustrating, as it does not seem repairable. No serviceman could give an appropriate reason as to why the washer would not drain, nor could they figure out why. It didnt matter the size of the laundry load or the type of items...towels, jeans, or silky delicates...the washer failed at turning from the wash cycle to the drain cycle. It also leaked because of the lack of draining, and began building up a mold film and odor even though I consistently wiped it dry and left the door opened when not in use. I received no assistance from Whirlpool and was given the runaround and told I must be doing something incorrectly.

At least three times a week the washing machine does not wring the water out of the clothes. The best Maytag wants to offer is to extend the warranty for one year. So washers are supposed to last for 2 years? Will never purchase a Maytag again!!!

Refrigerator, less than one year old, quit working and destroyed several hundreds of dollars worth of food. Whirlpool warranty division was notified and a service technician was scheduled to arrive yesterday, a week after the warranty division was notified. Yesterday, no one arrived. Today the warranty division was again notified and we were advised the service technician was never scheduled and they do not know why this happened. Here we sit again for another four days awaiting a service technician.I am disgusted with the failures of Whirlpool and their warranty division. Again, in less than a year Ive paid nearly three thousand dollars for a refrigerator and it fails, destroying hundreds of dollars of food. This has been a complete struggle trying to maintain food in a household both children. I expected a long time manufacturer to provide better warranty, service, and not just tell me they are not sure why. I would hope that no one ever buys their products again, God knows I will not!

We purchased our Whirlpool dishwasher/Model no. WDT780SAEM in July 2016 and it was installed on August 3, 2016. Right away we noticed 2 problems. The top tray squeaks very loudly when being pulled out for loading and unloading. The usual temporary fix for this would be using a product like WD-40. Of course as soon as you run the dishwasher all of the product is washed away. This was our first complaint about this dishwasher. The more important problem was the white cloudy residue being left on all of our clear plastic cups and glasses. Weve always had hard water but our previous dishwashers were able to remove the residue if we used the high-temperature wash. After looking at all of the manuals and user guides that are included with the purchase we read that we should be using a rinse agent and a product such as Lemi Shine to deal with hard water deposits. We tried these items and nothing worked.Using the All Fresh tabs didnt help and our filter was clear and clean. So we made an appointment to have the Whirlpool factory serviceman come out to look into our problems. First of all the customer service representative I spoke with was rude and impatient. She kept cutting me off and asking me about hard water and suggesting that I use all of the products mentioned above before finding out that I already had used them to no avail. Because we had the dishwasher for just over 30 days I asked her about the Clean and Quiet Guarantee that I found out about by going to Whirlpools site. Her exact words were The clean and quiet what?? So I didnt have much hope for our service appointment. Our serviceman was asking all of the same questions about hard water and if we had tried all of the products I mentioned above.After his visit we found out and now (too late) know that because our new dishwasher does not have a heat booster or the ability to get the water temperature high enough to remove the hard water residue theres nothing Whirlpool will do for us. This is the case with all newer technology dishwashers UNLESS you purchase one with a heat booster. I sure wish this wouldve been made clear to us, the consumer before making our purchase. If we had known beforehand that new dishwashers no longer get the water up to 140 degrees which is what would be needed to remove the residue, we wouldve made sure our model included a heat booster. Now were stuck handwashing our plastic items if we want clear dishes. Its not the end of the world but its not good customer service or honest to the consumer in any way, shape or form.

This Whirlpool Washer Mod # 4800XQ2 eats holes in all of my clothes, came from Lowes. I still have the sorry machine.

Bought a model wdt730pahz in Nov 2017. Up until recently it ran fine and we were very happy. Some folks have reported that the soap dispenser door gets stuck. Same here. In our case we found, when using those detergent pods, to make sure that they are pushed all the way into the dispenser before you close the lid, or the lid jams. Other than that, the dishwasher got the dishes nice and clean. However, after just two years of using it maybe 3 times a week (there are only 2 of us) the motor died. Youd think a new motor ought to survive at least 500 cycles. Anyway, parts and labor was quoted at nearly $400. Debating whether to fix or replace the dishwasher. Might try ordering a motor and pump and replacing it myself.

Late on the evening of Monday, January 27, 2014, after springing a leak in my 8-year-old water heater, I purchased a new Whirlpool model N50T61 replacement from Lowes. Installation went smoothly and the unit lit off fine the first time. It heated the initial tank of water rather quickly, but the next morning, I noticed the status light on the control unit was not blinking, which indicated the pilot light had gone out. I relit the pilot light, the water heater fired off and appeared to be working properly. 12 hours later, the status light was out again. I relit the pilot, but within 20 minutes, it went out again.On Wednesday, the 29th, I called Whirlpool customer service and explained to the representative what had been happening. He stated that since the status light was not blinking a code, the problem was either an air supply or venting problem, and he couldnt help me. I relit the water heater again and performed the match smoke test described in the owners manual on the vent connection. It did exactly what the manual said it should do, so I assumed that was not the problem. However, while performing this test, the water heater went out again. This time, being right there when it shut off, I saw the status light blink twice about 5 or 6 times before it quit blinking all together. The two blink error code indicated low millivolt signal from thermopile.I called customer service again and explained to the representative what the first person had told me and also told him the results of my test and that this time, I had observed the two blink error code. He asked if I had a multimeter (which I do), so he had me disconnect the wires for the thermopile, connect the meter to the wires, light the pilot and read the voltage. My meter is an old analog unit, and not capable of reading millivolts (which is what the thermopile output is), and I informed the rep of this, but he had me do it anyway. As I suspected, I saw absolutely no reading on the meter. The service rep stated that he believed the error code and decided to send me a new thermopile assembly. However, their shipping department was closed for the day and I should not expect to see the new part until Friday. This was unacceptable, but he stated that this was the only option available to me.After thinking about this situation for a while, I again called Whirlpool customer service and told the representative that I was not satisfied with the solution previously presented to me and that I wanted a return authorization to take the water heater back to Lowes for replacement. The rep stated he couldnt do that, but said that there were a couple other things I could try. He attempted to explain these procedures to me, but wasnt able to do so clearly. He stated he would email the instructions to me. As of this writing, I still have not received the instructions.In the meantime, I did some internet research and found that Whirlpool water heaters have numerous chronic problems, including the issues I was experiencing. I decided this was not a product I cared to own. I called the Lowes store where I purchased the water heater and spoke with the manager. I explained the entire sequence of events to him, and he told me to bring the water heater back for a full refund. Since my local Lowes store only sells the Whirlpool brand, I took the money and purchased a different brand of water heater from another home improvement store. Needless to say, it will be a cold day in hell before I ever purchase another Whirlpool product.

Whirlpool Cabrio washer and dryer set bought 5/25/2012 - The washing machine started beeping during the drain cycle and I have to reset it. After messing with it for around 30 minutes I can finally get it to drain. Then last night the dyer started making a loud squeal. I called and it is not under warranty anymore, so I have to flip the bill. My last $75.00 set from a church sale lasted 15 years. I paid $1,331 and this is the worst piece of crap I have ever bought. Lowes will not fix the problem when there is 1000s of complaints. I would have never paid this much, if I knew it wasnt going to last!UPDATED ON 05/15/2015: Whirlpool sent out Appliance Hospital to diagnose the problems. The washing machine needs a new tub, seals, circuit boards, drain motor etc and the dryer needs everything + an idler pulley because the original one disintegrated. The part they want me to buy is the same one that already failed. The cost to fix it, is over the amount I paid. REALLY? Somebody needs to do something to help the consumers. Blogging doesnt seem to help. I am handicapped and I have to go to the laundry mat now because I cant afford another set. DONT BUY WHIRLPOOL.

I have had my washing Machines since 2011 and have had continuous problems with the washing machine during spin cycle sounding like a freight train going through my house. Whirlpool has had people to my house 5 times to fix. When warranty was up in 2012, I was told they would continue to cover this particular issue. They came out again in April 2013 and now I am being told, Too bad; if you want fixed then you will need to pay for it.

I purchased a Whirlpool dishwasher and refrigerator/freezer from Home Depot. Within weeks the stainless steel on both products began rusting. They sent a third party repair service to look at both products and determined that, in fact, the stainless steel was rusting. Our technician said that both the dishwasher panes and the freezer doors would be ordered and replaced the following week. This was on September 4, 2015. After several promised arrival dates, the parts never arrived. I called both the third party repair company and Whirlpool on several occasions only to be told they were on back order. Finally, in late November, the new dishwasher panel arrived and was installed. It is now December 17, 2015 and our freezer door is still on back order. When asked what my options are, the Whirlpool representative simply said we have to wait. I said that because I have been so terribly inconvenienced that they should just come and pick up this piece of junk and replace it with a new one. Evidently, that is not an option. I will NEVER purchase a Whirlpool product again as they do not back their warranty. I now have a $2,000 rusted refrigerator freezer to adorn our beautiful Christmas kitchen. Thanks, Whirlpool. Youve certainly made this a Merry Christmas. (Yes, sarcasm in play.)

Have a Whirlpool side-by-side with water and ice dispenser on the door. It has lasted over 20 years. It has a large ice maker which makes more than enough ice and it has never broken. Since it is older it does not have gallon depth shelves on the door, but I have never missed not having them there is plenty of internal shelf space.