This stove was in my house when I bought it. It has a glass top on it with marks for each type of burner below. There are a couple of different size burners which makes it very useful. The only problem is with the glass top feature. It gets marked easily even when you try to be careful and many of the marks will not come off with anything I have used. The marks are so prevalent that I would never buy another one.

I took the Sears salesmans suggestion and bought a high-end quiet dishwasher. It worked wonderfully until it sprung a major leak. Computer told me the phone # to call. It took a week for the Sears repairman to come out and $79 fee to just look at it. He said the fitting between the sump and the pump came off and flooded water over the electric motor. Electric motor is shot! Cost to repair is over $400 and a 3-week wait!!! When and if a new motor is installed, only then do we know if the computer is also fried. This was a high-end dishwasher. Factory warranty just ran out. Repairman said this is a common problem with this model. DO NOT BUY THIS MODEL.

In 2007 our Whirlpool 30 gallon gas water heater began to have issues. Serial number 0425126675, Model Number FG1F3030T3NOV. The pilot light kept going out and would not stay lit.. After several times with replacement parts being sent with the same thing happening, finally in 2010 they replaced the water heater. A new water heater was professionally put in, serial number 1023T412357 Model number BFG1F3030T3noHV.I am having the exact same issue and I was told that the warranty was null and void on the new water heater because it was a replacement. They replaced a defective water heater with a defective water heater. I called the number given to me by Lowes 1/877/817/6750. I spoke with Nichole. I told her that I should not have to pay for replacement parts for a defective water heater. I told her that I was never informed that there would not be a warranty. I live on a fixed income and cannot afford to buy another water heater because I was given a defective water heater in replacement for a defective water heater. I became angry stating, Thanks for nothing and I hung up. So many people have the same problem with these water heaters that something MUST be done.

August 26th 2014 purchased a NG (NO GOOD actually natural gas) Whirlpool water heater from Lowes. Model No. N40561-403. Installed it and everything was fine until this morning August 29th 2014. The indicator light was out and so was the pilot. Tried to light it without success. Called Whirlpool and they are sending me a new controller that now needs to be installed. Called Lowes and they will not take it back. Wish I would have found this site prior to this costly fiasco. Waiting on part now and I will keep you informed as to my progress. I have a feeling this is going to be 2 days wasted and $367.00.

I dont recommend this product to anyone. When you try to clean the washer it leaks out the bottom. After 2 years of use it now beeps 9 - 10 times and I have to reset it after each beep to get it to run. Then in the middle of the rinse cycle it does the same thing all over again. What a piece of junk. Plus it does not rinse well at all. Leaves a white residue on my blankets. NOT recommended at all.

I just bought a new dishwasher because my 5-year-old one went out, model number DU1145XTPBA. After pulling the old one out, I took the motor out and lo and behold, what did I find but bad bearings. The motor was fine, just the bearings were rusted out and were jamming the motor so that it wouldnt move. The price of a new motor, $149.00. Well thats a bit much for something that only lasts 5 years. I went on eBay and found them for $70 to $170.00. So if you have a problem where your dish wont wash at all but fills up with water, it may be nothing more than cheap bearings in the motor. If I, myself, were this companys CEO i would really consider changing companies that they have making these motors or at least the bearings. Just wanted you to know that this is the only problem I have had with this one and Im going to replace the motor now that I know what it is. Thank you Whirlpool for a day spending repairing and replacing one of your dishwashers. I learned a lot.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

We purchased this washer and dryer new in 2011. Have repaired door to washer twice. New doors total cost $500.00 each time. Now it is cracked yet again and the dryer door has to be adjusted. The temp does not work right. Have to do minimum of 2 cycles for drying. Very unhappy. We may as well buy a new set of another make. Tired of the expensive repairs.

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!

Whirlpool Cabrio Washer model WTW6400SW2, serial CU2372784 type 480: I have had this set for about 4 years now. First, I had to replace the motherboard. And now today, I found out that the center post seal was leaking and caused a lot of damage. I was told that it would cost around $300 plus to get it fixed. I have seen on sites that this washer is a lot of trouble and the makers need to fix these problems. Also, the washer sounds like a jet running. We need the makers of Cabrio to step up and fix these problems or refund us the money that we have paid out for this thing. We, the people who have bought these machines, need a lawyer and to start filing lawsuits against these people.

Purchased this refrigerator, Model # WRS965CIAH on October 3, 2014. Paid extra for counter depth. Initially the refrigerator worked fine. After about 9 months we noticed the food in the back of the refrigerator especially on the top shelf started freezing. This started getting worse over the next 2 months. When I called Whirlpool 10/19/2015, 800-253-1301, I was told by their representative that this was normal, that air from the freezer blows into the refrigerator through vents and to just re-arrange my food so that it is not pushed to the back of the refrigerator. I asked him if this was normal why wasnt this happening in the first few months but only developed later? He had no answer. I asked him if it made sense if this was normal then everyone who buys this refrigerator has to make sure their food is not pushed to the back of the unit, then why dont they state that in the directions for use??? Ok everyone make sure every day you push all your food to the front of the unit so it doesnt freeze ridiculous. He just said thats the best thing to do. I asked him if I could talk to a technician, if maybe there was a way to fix it manually and he said there were no technicians there. I asked him if he knew about the lemon law and he said they dont have that there... ok. The refrigerator is just days after the 1 year purchase so he basically said just to call where I purchased it that Whirlpool could do nothing for me. Is this how Whirlpool trains their employees??? Good job Whirlpool, way to go. Luckily I purchased the extended warranty. Will see how the repair goes and report back. Did not call sooner due to health issues. Its not like the refrigerator is years old and started to break down - this is within a year. Whirlpool doesnt care about quality. Will never buy Whirlpool again and will spread the word as often as I can.

4 years ago, we purchased a Model UMV1160CW-3 over the range microwave. After 14 months the door cracked around the handle and eventually fell off. We made the HUGE mistake of buying the same model for ease of installation thinking that this would be a typical issue. We purchase another duplicate model in April of 2016 and less than 16 months later the same issue occurred. Spoke to customer service on 12/28/2018 and they told me that they would pick up the cost of the parts but I would be responsible for labor which actually exceeded the cost of the microwave. Exceedingly poor-quality product and support. Will not purchase another Whirlpool appliance.

As a busy mom with 11 children, I needed a refrigerator that could stand up to the demands of my family. This refrigerator is great and meets my needs, but could use a few improvements. The side refrigerator shelves are not on very sturdy. When my daughter removed a jar of mustard, the shelf came off the door, fell onto the floor and broke. This could be solved by improving the gripping strength (increase depth) of the refrigerator door shelf holders. Additionally, the sliding freezer shelf is always crooked and has to be manipulated into place. This is most problematic when the freezer shelf is full. The freezer is not smudge-proof, but clean up is easy with a damp towel.

I just wanted to post a quick response to a problem that so many people are having with their Whirlpool FG1H5040T3NOV Hot Water Heater. The biggest problem is the Pilot Light Wont Stay Lit. Ive had this water heater for many years now (since 2005) and two days ago we didnt have any hot water. I checked the heater and found that the pilot light was out and that when I lit the pilot light with the igniter, it wouldnt stay light. This could have been a number of problems causing this issue but heres what I did to get it fixed. I looked around on the internet and saw that many people had this same problem and several years ago Whirlpool gave out warranty replacement upgrade kits to fix it. I called Whirlpool support, gave them my serial number and mentioned the upgraded kit. Unfortunately, my 9-year warranty expired a few months ago and I am no longer able to get the upgrade kit for free. Apparently this upgrade kit was part of a settlement for this water heater that was sold through Lowes. The upgrade kit has a few enhancements including an adapter to allow the use of a standard right hand threaded thermocouple as well as a larger pilot light window and added safety thermal switch. This is definitely an improvement over the old.Anyway, I looked at Lowes website for this upgrade kit and their description and internal part number is slightly different but it is the same thing as confirmed by Whirlpool. Whirlpools part number is 6910813 for the conversion kit. Lowes calls this part American Water Heater Company Gas Enhancement Kit 5040T NG. This kit is only $35 which isnt bad. So, I went to Lowes, purchased the kit. The instructions are included and are even good for a novice. It took me about an hour to complete the changeover. Youll need to remove the old burner and orifice to use them on the new kit. I then checked for gas leaks. I lit the pilot and when I turned on the heater, the burner lit right up. All is good now!

Very dependable. Like the steam clean function. Love that it is front loading. Like that the machine has windows. The functions for towels is a plus. Time remaining convenient. Machine is very good looking.. A big plus is the choices of many different functions, many that I have not yet used, but are available too.

Doesnt wash clothes properly - often some items of clothing just dont get wet. After 3 years the whole main bearing in it failed, causing unbelievable noise and constant overload faults. All Whirlpool top load washers have this critical design fault where water leaks into the main bearing (the bearing is an unsealed type with a cheap grommet seal) and then after a year or 2 the bearing starts to cease and the machine overloads itself trying to operate. Replacing the bearing means pulling the whole machine apart - and with a cheap press-fit bearing like this, special tools are needed and it will never operate smoothly again anyhow. In any case in 2 years, the faulty bearing seal design will let water destroy the bearing again. Effectively it is not repairable. Sounds like class action to me. So, it became an $1000 paperweight and I bought a new Samsung unit. I assume the Koreans know how to design bearings and seals...

I have a two year old Whirlpool dishwasher. The soap dispenser cover broke shortly after the warranty ran out. It cost 100.00 for repairs. A year later, it broke again. I sent a letter and the part to the CEO of Whirlpool. They sent a repairmen to fix it free of charge. When you have a problem with a Whirlpool product go to the head of the company. If they get enough calls they will make better parts. Call 1-269-759-6919. Write a letter, return request receipt. It takes a little effort, but it helps a lot of people.

All of these awful reviews and you continue to sell the Made in China JUNK!!! And shame on the stores that advertise and sell Whirlpool JUNK!! They should put a warning on these machines stating Will not last, gets off balance and does not clean your clothes. Yes we bought the Cabrio like the others, our clothes would not get clean, because like sheets, would end up looking like a doughnut without a hole and all of the dirty water would drain through the middle and make a spot. Then you have to wash them over and over. But that is not the worse part! It only lasted 13 months, YES I said 13 months just past the warranty LOL!!When the man came to make repairs, it was the gear box and was going to cost almost $600. Almost as much as we paid for the machine. He recommended getting a Speed Queen, we did and I LOVE it!! I think it is the BEST MACHINE I have ever had. They are a little hard to find though, but I found where they were sold on the internet and the dealer had to order it. Well worth the time and trouble, (trouble) which I dont expect to have with this machine. Like I said it is a wonderful beast. And I will never buy another product made by Whirlpool. Before my husband retired he made prototypes for autos so he knows about testing and Whirlpool had to know this product had bad flaws before they put it on the market, I call that fraud. Bad taste in my wallet, Michigan.

Refrigerator was purchased in March 2015. Icemaker filled the basket two times then never worked properly again. The water would enter the tray, freeze, but never drop the cubes. In order to drop the cubes, we had to unplug the refrigerator for a moment then we would have those few cubes. We used one service company sent by Whirlpool that came 3 times, adjusted temp, and replaced one electrical part. It didnt work. The repairman was going to call for support from Whirlpool to see if anyone else had had this problem. I didnt hear back from him until I called him 1 1/2 weeks later. He basically said there was nothing else he could do. Whirlpool sent out another service company. He replaced 2 electrical parts. They didnt work. We have no choice but to keep having service men come out and try to repair the refrigerator. What happens when the warranty has expired? They are trying to sell me an extended warranty. Give me a break. It would be nice to have a working refrigerator first. I wish I would have read these reviews before I ever bought a Whirlpool. Im 78 and Im still learning. Never again, Whirlpool. Ill spread the news as well because we all work too hard for our money to throw it away on poor products.

I bought a Whirlpool water heater from Lowes. I had trouble with it from day 1. It never worked correctly. Their service department is terrible. All they want to do is sell you extended coverage policies on it. Every time I have it fixed, its never covered, and I have to pay again. You will be sorry if you buy a Whirlpool water heater.

The oven continues heating up even after it reaches temperature. This happen soon after we purchased it in 2009... When I called Whirlpool they said to unplug the oven for 15 min & allowed it to reset. This worked, that time. It has continued to happen to the point now where it will not reset and then we can no longer use our oven.

Soon as warranty expired issues with product. This should not happen. Made in America, washer making too much noise. Products cost more but poor quality. What is this company going to produce? This is the world we live in.

We purchased the Whirlpool Duet Sport matching washer and dryer new in 2006 from a local appliance store. The washer was around $1,000. The salesman sold us on the load capacity, telling us it can wash 15 pairs of jeans. We dont overload it, mostly because its a high-efficiency washer and doesnt use much water (Im still trying to figure out the concept of how can you clean a whole load of laundry with a little bit of water). Its very quiet, but the cycles take longer than standard washers.Also, you must use very little soap (too much soap will cause the washer to stop and display an error code, which youll have to call a technician to come and reset). It is now 2013, and the washer started thumping during a cycle and there was a burning rubber smell. We called an appliance repairman who gave us an estimate for repair of $800 to $900 (for a bad bearing/bearing casing and inner basket). Im sure that there was quite a markup on those parts! It seems to me that the older non-efficient washers lasted longer than 7 years, and certainly didnt cost $1,000 when new.

My washer is a top load, energy and water efficient model. I am amazed at how little water it uses and how well it cleans. I do have two issues, the capacity looks huge but it will not take a queen size and double sheet set in the same load. It unbalances and then cant seem to get going again. The other issue is that you cant pause the wash and adjust things, you have to cancel and start over.

My Whirlpool Microwave is cracked all around the door handle and the frame with the insulation foam hanging out of the cracks. Dishwasher also having issues. Completely dissatisfied with Whirlpool Appliances. No longer under warranty.

Whirlpool Cabrio Washer WTW6200VWO & Cabrio Dryer WED6200SW1 - My Cabrio washer ties clothes in knots but the big issue is that if it goes to UL (uneven load). There is no alarm. Washer stops all operations except one. It fills up over the top, all over the rec room, out the door and down the street until someone alerts me! I run down, hit cancel and it drains. I unknot the clothes and start over. Then I mop up! Help! My Cabrio dryer has been through four door latches and I finally realize that the issue is that the latch and the protruding part do not line up evenly. This breaks the latches. Help!

As many others have posted - the Cabrio washer is awful. Cycle time > 1 hr. Clothes not clean and caked in soap even with extra rinse. Phone Whirlpool and found they dont care. All theyd say is its government regulation fault but for $100 they could send a technician to ensure it is working as designed. To environmental reasons for the new design, seems to me it missed the mark. Longer cycles, extra washes, extra rinses... All I can say is - Unbelievable!!!

Whirlpool Refrigerator model #GI6FARXXY0 - Bought this refrigerator at Las Vegas Store #3305 Home Depot, 12/07/2012. July 2014, the ice maker stops working. I replace it with another Whirlpool ice maker and that one stops and leaks water from the dispenser all over my floor. Im on my 3rd ice maker and its not working! I have no warranty but still...a refrigerator should last longer than this at these prices. Im trying to research problems with this refrigerator and it looks like now the refrigerator model has been discontinued! Cant find anything on it. I paid close to $1,800.00 and it lasted 1 year 1/2? Its turning into a money pit. My question is... after looking at all of the complaints concerning ice makers and water leaks on Whirlpool refrigerators... why hasnt Whirlpool addressed this problem with a recall?? Obviously, these ice makers are faulty even the ones you replace them with. The repairman told me there are no warranties and they would not take returns on them. Whirlpool knows there is a problem and doesnt address it. Consumers should be protected from businesses that know of problems and refuse to take care of them with customers. They are still selling faulty Whirlpool ice makers??? I paid extra to have a working ice maker and expected it to last more than a year and half for the price of this French Door, bottom freezer, refrigerator did. The doors look terrible as they do not clean nicely and leave streaks. From the looks of some of these complaints, this may only be a beginning of problems with this appliance. Totally disappointed in this product. I know I wont be looking at any more Whirlpool products. Im disgusted with their faulty products and no accountability. If theres a recall, count me in!

Whirlpool WRF992FIFM00 - Purchased new April 2017. Its October now. Service has been called 7 times so far. Ice maker has not worked since day 1. Fridge leaked all over the interior around the third month. Compressor went out in 5th month. Compressor replaced 2x so far. Every component piece was replaced on 5th month. Still no ice. As I write this compressor getting ready to go out yet again. Paid almost $3000 for this piece of crap. On first name basis with technician. He tells me that his guys work on this particular refrigerator CONSTANTLY. So far I have lost over $1700 in food and wages (leaving work to meet technician). Currently battling Whirlpool. My next step will be legal action if they do not refund or replace this stainless piece of garbage.

I bought my Whirlpool dishwasher, model #WDF560SAFMO in Nov 2016 with a 2 year extended warranty. In Jan. 2021 it quit working, was told by repairman that the dishwasher needed a new pump. Of course, it is no longer under warranty. To replace the pump will cost almost as much as a new dishwasher.

I came here to see if others have had problems with their Whirlpool Cabrio top load washers. I was amazed at how many others forked over nearly a grand ($1000 with tax and extended warranty) for such a heap of nothing. I have lived in the same house for over 35 years, same water supply with water softener. Over this time, I have raised my family and been lucky enough to only go through two washers until 2 years ago when I purchased this Whirlpool Cabrio machine at Lowes. As with others, clothes do not get cleaned. Residue is present and in the creases of the tightly spun and tangled load. After calling Whirlpool and Lowes on nearly day one of my original purchase, no concern was given. Instead, I received the What type of detergent or Could it be your water supply? or What degree of soil does your family have on their garments? A white terry cloth washcloth should not come out grey, even after bleach! My GE and Maytags of the past always did fantastic jobs. They just plain old wore out. As for my new energy efficient machine that takes 86 minutes to wash a load, with expensive HE detergent, an oxy clean pouch, special fabric softeners, I scratch my head wondering how can this be efficient? If a pair of jeans needs pre-soaking, it cant be done in this washer. Instead, I spray the jeans with pre-soak, add my HE products, then fill a mop bucket full of water and dump into the machine 5 minutes after the 86-minute session has started. What a joke! For two years plus, I have vented to my poor husband who thought he was buying me a new innovative state of the art machine to make my life easier. I only wish there was somewhere or someone that I could contact to get some satisfaction for my agony with this poor quality product! Yes, I am venting. I dont have another thousand dollars to spend for a new machine. Believe me, if there were to be a class action lawsuit for this lemon, I would be first to sign up!

Purchased Whirlpool Duet wfw9550ww00 in 2012 from PC Rich, who purchased machines in 5/11. Product stopped being made 5 yrs prior. Of course I did not know until my washer went and had service come to my house. He explained prior information, looked at my machine for 2 seconds and said someone put in a heavy load that machine was not able to handle and 2 belts broke and guts of machine are destroyed. Its a $799 fix, not including labor, youre better off buying a new machine. How does he know thats the reason for breaking??? The machine is 2 years old, not a scratch on it!!! Unbelievable!!!! Then states thats $114 for the service call. $114 for 2 seconds!!! Im absolutely furious!!! Whirlpool has a new program (if it helps anyone), if your machine is fairly new they will give you a invoice for 1/2 off a new Whirlpool... Take it from there. There should be a tremendous action lawsuit, look at all these complaints...

I have purchased 2 Whirlpool washers in the past 6 years. Both have been a huge disappointment in quality and dependability. The 2nd washer I bought May 8, 2015 had problems from the initial purchase. In just a little over 2 years I have had to replace the suspension rods, and now the transmission is broken. Both washers had transmission problems. I have bought my last Whirlpool products. I recommend persons considering buying a Whirlpool product check the reviews before you purchase! I cannot believe this company continues to survive.

The ice maker freezes up at least once a week. It requires removing the bin and chiseling the ice away. We have had repair here twice, and it still happens all the time.

Whirlpool Cabrio Platinum Washer - I have a 2 1/2 year old washer that has been serviced twice. This week 10/2/14 the service technician informed me that we had a bad tub bearing. The bearing failure caused a leak which corroded the rotor & stator. It was more cost effective to buy a new washer than to repair our unit!!!! Ive never heard of a washing machine needing to be totally replaced after 2 1/2 years. Any ideas how to deal with Whirlpool?

I have a Whirlpool built-in double oven. It is 7 years old. The top oven has overheated 3 times with food in it and it locks the door. The oven beeps and says, Too hot, and locks the door. Luckily I was in the kitchen when it overheated, so I could turn the oven off. After turning the oven off, the oven has to cool off before the door will unlock and the food can be taken out. By then, the food is really burnt.I called Whirlpool to see if there is a recall and they said, No recall, and the oven was out of warranty. So I called the repair shop. They said it was the control board and they were not sure they could get a new control board. I may have to find someone that can rebuild this control board. They said not to use the oven. It could cause a fire. I would think that they should recall these ovens. They should have a safety switch that shuts the oven off if it overheats like mine has done.

This is a freezer on top unit. Purchased in 2015, unit quit cooling, started making a roaring noise. Called local technician, he added 2 oz of Freon, said he has seen many of these same unit losing Freon. Technician said line that goes to compressor is copper and hooks up to aluminum line before attaching to compressor. This is leak point for freon; no way to know when the leak started, but freon almost gone and cost to pressure check for source of leak is costly and probably would not repair problem. Got 6 yrs out of it and I am replacing with another brand. Will never buy Whirlpool again. Should have got 10-12 yrs of use. Do not buy this unit. Wrote Whirlpool first, but no help. Indicated this could be a problem with these units but no recall so I am on my own. Out $900 for a new refrigerator. Big hassle. Unit no good.

I purchased a Whirlpool 50 gallon gas hot water heater 3 years ago. I have 3 daughters all in school age. When my old one finally quit due to tank failure and out of warranty, I went to Lowes and bought a 6 year warranty hot water heater costing around $600. Now I figured you get what you pay for RIGHT! WRONG! So about 2 years ago the pilot light started to just go out on occasion, a bit of an inconvenience but there was no default code warning me of any other issues. So typically we just relight it. I called Whirlpool to get help with this issue, but they wanted me to pay for a technician to diagnose the problem. Um isnt that what the warranty is for? I said dont bother. Im not paying $150 for someone to tell me what I already know. Ill just keep relighting it myself. So finally the pilot light goes out for the 100th time but this time I go to reignite it and BOOM! It sounded like a twelve gauge shot gun going off in my face! Then it flutters flames into the chimney of the hot water heater. Scared the crap out of me at first. But it finally stopped and run fine. Well Im laying in bed a few nights later and woke up to a loud thumping noise, I go down stairs and it stops. The following day Im in the kitchen and THUMP THUMP THUMP BURP BURP BURP. Run over to the hot water heater closet and theres the flames shooting out of the gas valve into the hot water heater then BOOM! Its out! The valve unit finally took a crap I guess. I call Whirlpool again to get my warranty - this time it definitely needs to be replaced. So the guy tells me the parts are covered in the warranty but a technician needs to look at it first and the technician Ill have to pay.. Excuse me but what the ** did you just say? I have to pay for a technician to look at your failing part? No I dont think so! Just send me the part - Ill replace it myself. Im a millwright electrician by trade. I specialize in power plants and refineries. Im sure this little gas valve wont be a problem. I spoke with these idiots on a Friday and he said I could have it ground shipped for free and it should be here in 5-6 days or pay extra for quicker delivery. What the hell did he just say? I could pay extra for quicker delivery on Whirlpools faulty part? ** whirlpool should be saying Well have the part overnight to you.Now since it was a 3 day weekend theres no sense in me paying $40 to have it delivered 3 day because it still wouldnt arrive until close to the five day. So I just looked to see where my damn part is because it shouldve been here by now according to the guy on the phone. NOPE! Its set to be delivered in 5 more ** days. DONT BUY A WHIRLPOOL PRODUCT. THEY DO NOT PRACTICE ETHICS.

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

We have an 8-year-old built-in Whirlpool Estate. It is probably as basic a model as you can get. It has been 100% reliable, and cleans the dishes well, even without rinsing. We do not buy expensive premium dishwasher detergents, either. So far, we have required no repairs. Basic features--heavy wash, normal wash, pots and pans. This dishwasher is standard (not extra large.) This is not a fancy dishwasher--just white. It is what matches the rest of the appliances. We have been lucky regarding the performance of such an inexpensive dishwasher. We paid about $250 for it.

Purchased Whirlpool front load washer 2010. Had it repaired 2013. Paid $599 for washer & $648 for the repair. Mailed copy of sales and repair to Whirlpool customer service. Received call from customer service and was told to have a nice day.

I purchased a Whirlpool dishwasher and have had it repaired four times so far. Last time they replaced the main computer located in the door. I attempted to use the dishwasher tonight and it is completely dead once again. I usually have had good luck whirlpool appliances. After all these problems will no longer be using this brand. I contacted the store where I bought it from, Famous Tate. The first time it stopped working just a month after the manufacturers warranty ran out and they were absolutely no help. So in the future, I will no longer buy any type of Whirlpool appliances.

I bought a Whirlpool WFW9470 Front Loader Washing Machine 11 months ago. The washer appears to complete a wash cycle but leaves the washing wet and with no error message or light. Whirlpool says the machine is not designed for light loads. The technician says washing on a light load will damage the bearing. We had the spin bearing replaced after 8 months. But still, the washing remains wet and the bearing wears out prematurely.

If you have the double oven below with bad board, start shopping for a new oven, but the part is no longer made. How can you end of the life a product after only 6 years? This is about the RBD305PDS12 double oven! I have wasted 3.5 days with Whirlpool/Maytag. Its very Frustrating how each department passes you along and makes promises about what the other department can do, resulting in zero satisfaction. None of them are well informed to say the least.I have a 6-year-old double oven that has a bad board and after 3 days, I find out it is no longer made. I paid $1500.00 six plus years ago and now I get to spend $2000 plus to get a new one. Again, how can you end of life a product after only 6 years?

I am so disappointed in my whirlpool W10431035A gold series dishwasher. I bought this 2 yrs and 2 months ago on black Friday at a lowes. I wanted to have a whirlpool and I thought they were a good brand. It has been a little over 2 years and my dishwasher no longer works. The start button no longer works. It is not even that old and appliances should at least last 4 years. I could understand if the plastic utensil holder or dishwasher rack breaks...fine, you use plastic. But this is an intricate part of the dishwasher....the start button and it does not work. I am so disappointed in whirlpool. It is the start button...how can this break. The only thing I do is press normal cycle and the start button...that is it. How can this machine break so easily. How can whirlpool build and sell such a faulty product. So disappointed.

In August of 2008 I purchased a Whirlpool Amana refrigerator, Model# ABR2227FES. It worked great for exactly 6 years. In Aug of 2014, the motherboard needed to be replaced as it was not forcing a defrost when needed. I tried to get a refund on the cost of the part and labour but both were refused. In Dec 2016, just two and half years after the motherboard was replaced, the exact same problem re-occurred. Again I tried to get a refund on the cost of the part and labour but both were refused. Will I be buying this refrigerator in the future? A definite no!!!

I bought a fridge from this company not even 14 months ago. Went away for a week and came home to a fridge and freezer of rotten food. The fridge had died - Im guessing not long after I had gone away by the look and smell of the food and house. I have had nothing but the run around ever since that day. Spoke to this person and then that person. The electrician confirmed that my fridge is completely dead because of the compressor. So they sent a report to Whirlpool and they have now confirmed that I will get a new fridge. Now Im being told that will take 7-14 days. So I have been left with no food whatsoever as well as no fridge. I have two kids and cant even buy shopping for my son to take to school. And now Im being told that I had 9 months left on the warranty for the fridge that died and that’s all I will get on a new fridge. Should I not receive a new warranty for a new fridge? And should they replace my food? Could really do with some feedback on this matter. Please help me.

The American Standard 95% 2 stage variable furnace is by far my favorite furnace to install. I know exactly what to expect from this furnace and I have had zero factory issues with this model. Outside of making a few sheet metal transitions this American Standard standard 95% furnace was very easy to install as well. And like the 2 stage variable … no factory issues.

I am getting numerous F1 codes on my Whirlpool Cabrio washing machine, Model #WTW6600SW2. By doing thorough research on this issue I can see the problem is in a known defective control board (part #W10130544). This part has even been replaced by Whirlpool with a new control board costing around $300 for just the part. After calling for repair service, two people (1 agent and 1 supervisor) refused to acknowledge any known issues with this part and further refused to any type of repair or replacement of the part. It is impossible for anyone in that position to not have knowledge of this problem. Simply look on the internet for a countless number of people with this very same complaint. Even though my washer is eight years old it has had very little use. There are only two grown adults in this household and the machine has never been abused or overused. It still looks new. Whirlpool should be honest and responsible when dealing with this type of problem. They should agree to pay for the part and repair service... at the very least they should agree to pay for the part.

I purchased this heater in 2009. I have had so much problems with the pilot staying lit or the thermocouple. Had to have that changed, have to clean under heater monthly. I have called Whirlpool numerous times because the pilot light goes out. Now I have a problem with it staying lit. Whirlpool tells me I have to pay for service labor. They sent out a technician who broke the igniter and I am being told I have to pay labor cost to have this fixed. THEIR TECHNICIAN BROKE THE IGNITER BUT THEY WANT ME TO PAY THE LABOR COST TO FIX WHAT HE BROKE. I have had it with Whirlpool. This heater is a piece of garbage as far as I am concerned. I am tired of having no hot water.

Sad that I have to file this review! After reading multiple other reviews on all brands available to American citizens, I have come to the realization that cheap labor and materials are creating massive appliance garbage in our country as well as financial rip off for us all. It needs to STOP! What has happened to doing things right!! What company is going to be the first to produce good refrigerators! Paid over $2000 for my side by side and it is only 5 years old and has a freon leak that cant be fixed. Repairman said will have to buy a new refrigerator. Pathetic!! Cheap manufacturing in foreign countries is killing our economy and our household finances. Be prepared to buy NOTHING that works! Yeah, thats what I work hard for and look forward to. Americans better wake up.

My new Whirlpool Stove, has two grill like tops, heavy duty and awesome looking. It has a special burner to keep food warm, a stainless steel front and bottom drawer for broiler storage. Broiler is also on top in oven, broiler flame.

Whirlpool Energy Efficient Top Loader - I re-wash at least 20% of all clothes because they have dark spots AFTER washing them, but NOT before! It is a moving target, wash out one dark mark; get another somewhere else. I bought great quality sheets that are permanently stained, because of this. No matter how you load this machine, anything with arms and legs gets entangled into a big knotted mess. It is difficult to separate them and time-consuming. This puts a lot of stress on the clothes, especially as the load spins. I also re-wash entire loads at least 4 loads because the clothes dont rinse properly. I bought a 5 yr. extended warranty and have had this serviced at least 4 times to no avail. THE PROBLEM IS IN THE DESIGN! I am POSITIVE of it. If you have these problems, as well, please contact me. I would love to investigate a class action suit. I am THAT mad.

The stainless steel refrigerator door is rusting after only 5 months and the company respond it is cosmetic and we the customer have to live with it.... They will send a cleaning product which didnt remove the rust. Review that was written on the company facebook page wasnt published because it didnt meet the company website guideline. Its disappointing and frustrating to realize that we have to go through it. Not happy with customer service.

We got a brand new bottom freezer french door Whirlpool refrigerator in our brand new apartment. Since we moved in last week the temperature control in the refrigerator box has failed three times. The freezer stays cold but the coils are frosted solid and no cooling gets up to the refrigerator box. We turned on moisture control but that didnt help. The users manual is completely useless and in fact doesnt even match the control panel. The numbers for temperature settings on the instructions dont match the numbers on the panel.We had to turn off and thaw out the unit completely three times already and this is just the first week! Last night the building maintenance guys came in and sprayed the back panel of the freezer with warm water. He said he talked to the GE tech, who suggested we also increase the freezer temperature settings to 4 and the refrigerator to 44. But this morning the temperature rose again. It sure sounds to me like the daily defrost cycle isnt running at all and nobody wants to consider that possibility. Thaw the unit several times a week is completely ridiculous. Our food has experienced so many temperature excursions who knows whether its any good now. I cant wait to get my first taste of salmonella. This is what you get when you combine junk with poor service.

I was excited to have an energy efficient washing machine and chose the Whirlpool Cabrio top loader. I truly wish I had read reviews rather than trust the salespersons advice. It does not clean clothes properly at all. They come out smelling dirty and are covered in white goo, even when the machine has just been cleaned. Stains never come out despite all of my efforts. Now I have water leaking out of the bottom as it fills. Not impressed at all. What a giant waste of money.

I do not know if my mail would be read or not, but I am writing it just to my satisfaction. I am a doctor (dentist) living in Haridwar. I had bought a Whirlpool fridge around 2-3 years back. I am not sure about the date. I have the bill. I will have to check the exact date. So around 3 months back, the fridge stopped cooling and I lodged a complaint in your customer care center. The engineer turned up, and he said that the compressor was not working and the company will change it. We only have to pay for the gas to be refilled. I said ok. Everything went well for nearly 3 months, then again one fine day, the cooling stopped. I called the companys customer care, and they gave me a complaint number and customer satisfaction number. But nobody turned up for 2 days. I called and called, then after much calling, a guy from the company came and said that the compressor was not working and they have to change it but that it will not be possible for 4 days. After 4 days, he will come.Sir, can you live without a fridge for 4 days and not getting the guarantee that it will be ok in the next 4 days? So, I went to the market bought a Kirloskar compressor, got it fixed, and got the gas filled; and the fridge is working fine now on the same day. This cost me nearly 4500rs, but I am happy that I have solved the problem. Till date, nobody has come to see my problem; and to my utter surprise, I received an SMS from Whirlpool that the customer is not willing to pay. Ha ha ha. My fridge is a double-door 280-liter fridge. What should I do?

We have purchased 4 refrigerators in the past 20 years. The first three were not Whirlpool and were a constant issue for us. Once we purchased the Whirlpool, we no longer had issues. We have the side by side with a freezer at the bottom. This model has performed exceptionally well for us and hasnt presented any issues for us. I would highly recommend it to family and friends, thus the rating of a five.

My microwave is very reliable and has lasted a very long time. I have never had a problem other than the circular glass plate that broke. It took me a little time to get use to the timer on it which is a little different than other microwaves that I have used. Overall a good buy.

Whirlpool N50T61-403 - I bought this thing today 8.21.14 from Lowes. It is a Whirlpool 50-Gal water heater (6th sense) and was going to have it installed by their installer, but elected after seeing it was very similar to lining up with my old unit. I got it in and then filled it. After filling, I lit the pilot light per the instructions then turned the knob for heating it up. Success, the flame spread across the burners...then went out. The steady blink changed to the 2 blink code indicating a bad thermopile. It did not work - right out of the box. No plumber near me carries the part. Whirlpool has thus been pretty good about it offering to have someone come out at their cost... But if no one has the parts, that is no good. I am moving from this house so if we can get it to work, its the problem for the next owner. If not - Ill have to get an RMA and go back to Lowes... Then try the Rheem from Home Depot. Will see if they will overnight a part tomorrow. I found the other reviews - and I dont like it that this thing appears to have difficulty right out of the box.

I recently purchased the Whirlpool Cabrio washer and it is the worst product ever!! It does not wash the clothes, it tangles it in knots and has ruined all of my clothes because it leaves holes in the clothing. I have had multiple service calls and all of the diagnostics check out. It is a horrible product that should be recalled and Whirlpool customer service does not stand by their product. Their supervisors and customer service is very rude and I will never purchase another Whirlpool product!!! I plan on posting my complaint everywhere possible.

The refrigerator does what it is supposed to do. The fact that I had to have it repaired only after 1 year of ownership confounds me. The space in this side by side is a bit crampy. Seems like Im always shuffling things around. I truly believe that Whirlpool made the condensation tray underneath the unit out of cardboard. It literally disintegrated and started leaking after about a year and it was 200.00 to have it replaced by a repairman. The water filters always tend to piddle on the floor too. At least I hope thats what it is, and not another wilted tray!

Something inside the machine broke causing it to tear up my clothes! I had it repaired once, now it is 4 months outside warranty and it is destroying my clothes again. Whirlpool will do nothing to help remedy my problem. They did offer to help repair it at a cost of $350. Not happy with my Whirlpool washer. Looking to replace my 16-month old washer.

Microwave didnt even last 2 years. I bought all new Whirlpool Appliances less than 2 years ago & they were not cheap! The microwave wont work until the light comes on inside. Well for some reason now it takes almost 10 minutes for the light to come on & I have to leave the door open until then. Now today I cant shut it because the light wont shut off & if I try to shut it the fans runs constantly. So frustrating as they dont stand behind any of their products! I will never ever purchase anything Whirlpool again.

I purchased a Whirlpool cook ceramic cook top for our new kitchen. The very first time I made something (it was lentil soup) something stuck to the cook top. I have had a ceramic cook top before for 18 years - never had a problem until the whirlpool cook top. I cannot get it clean. I have tried everything! Such as stove top cleaner designed for whirlpool cook tops ($22), other cook top cleaners, the single edged razor, a scrubby sponge, steel wool, I even resorted to furniture stripper - NOTHING has removed this spot. I am ready to throw out this new stove top! What a huge disappointment this Whirlpool product is.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

This dishwasher is so far advanced from what came with our new home 18 years ago. It is absolutely the quietest machine. You have to look at the light display to know if it is even running. Its a well thought out unit with the exception of the silverware accommodation. They used a flat low-profile basket attached to the inside of the door. Not accommodating enough space wise. Solved by augmenting the more stars compartmentalized basket that came with the old dishwasher. Would recommend and purchase again in a heartbeat!

I have had to replace the thermostat 3 times. Worst fridge I have ever owned. Lost lots of food and time and money that I will never get back. I will never ever buy another Whirlpool product again. Aint got time for that.

I bought a Whirlpool larder fridge 18 months ago. It suddenly stopped working so we got a service engineer up who said there was no gas. He said it would cost 50.00, but with no guarantee it would work afterwards.

My daughter bought a mobile home manufactured by sunshine mobile home co. in Red Bay al. The home is only 6 mo. old. In that home there is a Whirlpool microwave oven model # WMH2175XVB-1 Serial # TRY 20 23398. After 2 months my daughter microwave stopped working, Whirlpool sent a repair man out to fix it. He didnt have the parts to repair it so he left to order some parts that he thought might be the problem. When the repairman returned two weeks later with the parts, he replaced a door switch. The oven started to work. About 4 days later it quit working again. The repairman returned for the third time, tried repairing the oven and was unable. I had to help him remove the oven so he could take it home with him so he could try to repair it. At that time I was so angry that the Whirlpool co. would send a repair man out three times to repair something that was obviously junk. When I talked to the people at Whirlpool they told me all they were authorized to do was repair it. I explained the repairman has tried three times and couldnt and that they in good faith replace the unit. The answer I received had to come from a mentally challenged person. If this is the response of Whirlpool about their product, then I want no part of them in the future.

Whirlpool Gold Refrigerator, #GI6FDRXXY07 ICE MAKER PROBLEM - Ever since we bought this ref in 2012, we have been facing problems one after the other. First the refrigerator was shutting off on itself thawing the food the ref & freezer. (When we were on vacation, in summer of 2012 , it was a disaster when we returned home.) This a continuous on going problem... not fixed. Second 2012 Spring the Icemaker shuts off spilling water at the dispenser, when called customer service they sent a technician who replaced the ice maker. But again the icemaker is spilling water or leaking now. Third 2013 Winter, the bottom freezer was leaking and ice buildup at bottom. We have been having problems ever since we got this. WHIRLPOOL YOU HAVE DISAPPOINTED US, its been an exasperating experience. Please Help, its not our fault for your poor design & faulty product.

3 months after warranty the oven will not stay on. I will stay on for only 20 minutes then it goes out. It clicks but will not come on. I can only use my oven for backing biscuits but cannot bake chicken or meats.

My induction cooktop totally failed to work two months after installation. Whirlpool sent a repairman who told us it was the main board. He also said he was unable to locate any of that part anywhere in his computer. We called Whirlpool via our store, Ikea. They apologized, asked for 48 hours to locate a part, then said they would replace the cooktop if they were unable to find out. Almost 48 hours later, they hadnt located it and denied any replacement option. The parts cost is over $800. The cooktop cost just over $900. Whirlpool reps would only read from a script of legal warranty jargon. Then they said they needed 5 to 7 days. We had a baby visiting - we needed our stove. To me, an apology would be replacing that unit if the part wasnt available, not a verbal statement. Fortunately, we had the phone # of a local Ikea manager who told us to bring the cooktop to the store as they had them in stock. They replaced it with a new one. Over the years of my long life, I have bought many Whirlpool products. Never again. I need a washer and dryer, and will not be purchasing any associated with the Whirlpool Corporation. Thanks to Ikea, though, for standing by their customers.

Our Whirlpool Cabrio Washer did a decent job for the 3.5 years that weve had it. Last week, it stopped spinning properly after rinsing, leaving the clothes quite wet. The repair person said it needs a new control panel and is not worth repairing. So, we have to buy a new one after such a short time. Very disappointing. Next time, well try another brand and buy an extended warranty this time. Buyer beware!

I purchased a Whirlpool Cabrio and a one year extended warranty two years ago. As soon as my warranty ended, my washer started to malfunction. I recently started to receive the F-51 code and the washer shuts down at the spin cycle. I am angry because I spent just under 1200 dollars on a washer a little bit over two years ago and now, it is sitting in my laundry room taking up space. When I called Whirlpool, they told me I could purchase another repair warranty for $316.94, which would take the cost over 1500 dollars for this washer and there was no empathy nor compassion for what I was feeling as a consumer from the customer service rep. I spent my hard-earned money on major appliance purchase and I think that it is only fair that I get more than a two year usage out of machine that was designed to last at least six years according to their website. There is no way that this should just be my lost and cost me additional funds.

My Whirlpool Cabrio has been a real workhorse of a machine. It has been able to take large loads and small loads and get them equally clean and fresh. This was a more expensive model but it was worth the purchase price as I have used the various features provided. I also have appreciated that if you leave clothes on the washer overnight they are still fresh in the morning.

Certain brands of dishwashers made by Whirlpool, including Whirlpool, Kitchenaid and Kenmore, are a fire hazard. Most appeared to be made in the mid-00s. My Kenmore Elite, model# 665.16293400, bought in March 2006, started emitting a burning plastic smell. I removed the door panel and found where the control board wires have been overheating and melting the plastic liner inside the door.Further investigation led me to kitchenaidfire.com, which details the models involved and includes hundreds of reports of fires from these models. I also searched saferproducts.gov and also found over 100 reports of fires from these models. The report logs are growing rapidly as it appears most of the control boards start to malfunction about five years in.I called Sears and they said that Whirlpool needs to do a recall. I called Whirlpool and I was told that they do not make Kenmore dishwashers, only some parts. This is completely false. I couldnt believe the representative was told to tell me that besides the part that is failing is stamped Whirlpool. These Whirpool-made dishwashers are a documented fire hazard and need to be recalled. I do not know what it takes, hundreds of fire reports have been logged and they are rapidly growing, but I hope that it doesnt take someone to be killed before they are recalled.

I purchased a Whirlpool classic range model number rf263LXTS0 on January 2010. We had some hang-ups on the kitchen renovation and were not able to install the appliances until May of 2011.I used the cooktop that evening and was very pleased. I then went to use the oven 2 weeks later and it did not heat up. I asked the contractor to check things out (maybe it was something minor that he could fix). He checked the things that he installed and everything on his end was working fine, so he told me to call Whirlpool.A service technician came out and, within 10 minutes, said that the oven controls were defective.I paid $450.00 for the oven originally. The service technician charged me $136.74 for 10 minutes to tell me that the oven control needed to be replaced (that is the major part of the oven) and that it would cost me $318.41 to replace the part.I called Whirlpool and explained my circumstance and Paula, the supervisor from Tennessee, said that there was nothing she could do. I told her that even if I installed the oven back in January of 2010, the major part of the oven should last more than 1 and 1/2 years.What terrible craftsmanship and crappy customer service. It is sad that customer service cant stand by their product and Whirlpool has to rely on making their money on repairing defectives products. I now have to go out and buy a new oven. I also buy a lot of appliances in my business and I will never buy a Whirlpool again.

My wife and I purchased a Cabrio washing machine and dryer, this is by far the worst washing machine we’ve ever owned. It hardly fills, even in deep water cycle. If you watch the clothes through the smoked glass lid with a flashlight, you can see they don’t even go underwater. The dryer seems to be fine but I would never recommend the washing machine to anybody looking to buy one.

Worst refrigerator Ive ever bought. Previous one still perfect shape. 22 years old. Freezes everything on top shelf. Motor making grrrr noises. Had repaired. Now bottom crisper drawers so cheap the plastic is breaking. Drawers wont slide. Now Deli tray lid snapped in half! STAY AWAY from this USA made product.

I purchased a 40 gallon water heater at Lowes and installed about 3 years ago. A couple of weeks ago, it got an upper sensor failure code on the gas valve. It would heat by resetting (turning valve off, waiting a minute and then lighting) but after a few minutes, it would fail again. I called the customer service and they mailed out a new upper sensor. When it came a few days later (I paid for shipping), I installed it but the same failure code. Again, the only heat I could get was by resetting the valve several times before a shower. I called customer service again, told them what I did and they said, Oh, the problem is the gas valve then. So they mailed out a new gas valve unit. It then came a few days later and I installed it according to the enclosed directions to the letter. Still got the failure code and still had to keep resetting it to get any warm water before a shower.I called customer service again, told them what I did and he said, Well, did you flush the water heater with apple cider vinegar before you installed the new gas valve? I said, No, it wasnt in the enclosed directions to do so. He said, You should have done that and it would have worked. I will send out a new gas valve. At this point, I blew up. Two weeks with no reliable hot water. I told him I want a new water heater and he refused. I asked to speak to his superior. He said no. Dont ever get a Whirlpool product. Some other crappy company builds these turds.

We had purchased a Whirlpool Duet Sport Washer and Dryer in 2007. Since that time we have had several repairs on the dryer, resulting in us having to purchase an entire new unit in 2011 (4 years old), along with mold that has accumulated in the washing machine on the tub and rubber seal that cannot be removed after several attempts utilizing several products that were recommended. The end result is our laundry that has been washed - comes out with a musty odor. Not happy at all with the top of the line, best possible machine to produce clean laundry as was sold to us! This has been a nightmare, and a totally dysfunctional appliance that should have lasted longer than 5 years!

We purchased a new Whirlpool Cabrio washer, model #WTW6340WW0, and dryer unit 2 1/2 years ago. We did our research online; Consumer Reports got great reviews everywhere. We went to Lowes and was told that this set (washer/dryer) was the top of the line in top load washers, so we purchased it. Now 2 1/2 years later, our washer is out of service, bad power board is the suspect and maybe the pump. I have heard that there may be a class action lawsuit coming down the pipe against Whirlpool and would like to know more info if it is. We paid nearly $1,000.00 for the washer and like other complaints, we were led to believe that we would get 10-14 years service out of the unit. But that did not happen. I think Whirlpool, Consumer Reports and Lowes should all be held accountable for misrepresentation. I can assure you that all of their executives received attractive bonuses for misleading the consumer. I would not recommend Whirlpool to anyone, Consumer Reports nor Lowes.

Bought a Whirlpool Cabrio. Noticed it was getting really loud less than a year into owning it. Called while it was under warranty. The tech said it was fine. Within the next year and a half it got so loud, you cant hear anything else in the house while it is running. Now it is leaking from the tub seals and the bearings are going out according to two service techs I have had come look at it. They say it is more expensive to fix than the washer is even worth. This is due to the parts that would be used to fix it are the same cheap Whirlpool parts that were put in it in the first place. They both said that these are not good washers and commonly go out about a year and half to three years old. Shame on Whirlpool for making such a low quality product and not being willing to do anything about it.

We recently purchased a refrigerator from a reputable local appliance store after months of shopping and comparing and research. As an opinion, Whirlpool seemed to set the standard for a quality appliance. Unfortunately, we failed miserably by buying this side-by-side fridge. Two unsolvable problems. First, the cold side door is extremely difficult to open. Ive tried ALL gasket lube methods and failed. Second, the stainless steel used on the front of the machine is obviously low grade that accepts magnets and is almost impossible to clean weekly without streaking. They were kind enough to provide us with their special cleaner {free} but it takes about an hour and a half to use for moderate success.The lady on the help desk listened but seemed rather cold and uninterested in the problems. At this point, we would be willing to pay the extra and go to a Kitchen Aid instead. Our advise is beware of these types of issues and get some kind of guarantee from your store when buying a WHIRLPOOL refrigerator. This is simply terrible.

My double oven is only 6 years old - it stopped working on xmas day, had a repair man look at it. He has phoned Whirlpool and has not had his calls returned to buy the part needed. Why is this. I need my oven, why is Whirlpool making it so hard for me to have it repaired.

Recently bought a 19-cubic ft French Door Whirlpool refrigerator. Seems to work fine at this point, but the compressor/cooling system has a fairly loud swishing noise it makes off and on during the cooling cycle. According to the owners manual, this is normal. If I had known this, I would not have bought this brand. Believe me, it is loud and you can hear it from all parts of my apartment. Also, once you examine the fridge up close, it really is cheaply made. Low-grade plastics for shelves and compartments. And this was not an inexpensive product to buy. We are talking out the door paying $2,000. Sad it is American made. My parents bought a Samsung last year and it is of much higher quality than the Whirlpool I have. But so far, it is keeping the food cold. Just wish it was quiet.

My Whirlpool has all basic features and works for household jobs. It is extremely useful for routines like towels and clothing. It also works gently enough to launder curtains and goose downquilts. Operations are very simple and the controls make it very simple.

Regarding a Whirlpool Refrigerator (model ET8CHMXKQ04) purchased in 05. I dont remember exactly when the problem began but the freezer starts its defrost cycle, water drips down through the refrigerator compartment (soaking all paper/cardboard covered products), collects under the crisper trays and eventually spills out onto the floor. Its a river of water that requires a towel to collect.I believe whats missing is some sort of collection funnel and tube that catches this dripping water and delivers it to the evaporation tray behind the base cover plate under the refrigerator. Obviously, Whirlpool has no quality control nor does it do any field tests to ensure their products are designed and operate properly.

Buyer beware! I purchased a Whirlpool Cabrico topload and with my second wash, I realized I had a mess of a new washer. Ive called the call center on 3 separate occasions and I have spoken to other customers who have the sample complaint. The clothes are not washed clean. They have a residue left on them. My advice to all potential buyers, dont even consider buying a Whirlpool Cabrio washer. It is the worst purchase I ever made in an appliance. Im very unhappy with my washer.

I just bought a brand new Sterling steel refrigerator not even 2 months ago, and since I got it, noticed rusty spots coming out,and now has spread all over. I called customer care, and they said it wasnt cover under the guarantee,and to buy a special spray out of my pocket expensive to remove the rust. I am Very disappointed with the service I received, for its not even 2 months old refrigerator and it looks like it is old now. In addition, the company didnt offer to send someone to take a look, checking and make sure theres no future problems with my new purchase, and as a courtesy removing the rust free of charge.

Warning: Whirlpool water heaters are junk! Spent $553.00 for a high quality ( lmao ) water heater that had a 6 year warranty. Started leaking internally and rusted through, then rusted a hole in the bottom. 6 years and 3 months later they said you are S.O.L. Leak occurred well over 3 months ago, but they said it has to be reported before the 6 years. Do not waist your money on this junk!

I have had problems with my electric range (Whirlpool) since day one. It always ran hot. I wrote letters to Whirlpool and received one very condescending phone call. Now two days before Thanksgiving it is running terribly hot from 350 to 500 degrees. When I called Whirlpool they said the best they could do was offer me a maintenance plan for 293.00.

It was obviously designed by someone who has never had to clean a refrigerator. There are grooves in the door gaskets seemingly making their sole purpose to collect crumbs and mold with no obvious way to keep them clean (No, Q-tips dont do it). A layer of ice forms below the basket in the freezer (bottom freezer) which, when it melts, soaks the kitchen floor. Ice must be chipped out at least every two weeks to avoid flooding.

I purchased a new French door refrigerator in May of 2016. Professionally installed. Last May 2017 icemaker stopped working and was replaced. June 2018 icemaker stopped working. This part of the refrigerator is poor quality and because of that I will never purchase another Whirlpool appliance. They use to be good quality and dependable. Not anymore.

Whirlpool Quiet Partner II Model # DU1055XTUS1 - We bought the dishwasher in Aug 2010 and after the 2nd yr, it started to occasionally shut off by itself in early cycle. After 3 yrs, it now shuts off repeatedly... needs to be restarted at least 15 times. It use to shut down early in the cycle. Now it shuts off whenever. I should have read the reviews on this dishwasher before buying but it was on sale for such a good price. I guess I got what I paid for. Just keep in mind that Whirlpool dishwasher seem to last only 3 years. I guess thats also why their warranty for electrical parts is one of the worst compared to other brands.

I went to get ice from my Whirlpool Gold refrigerator, model GB2FHDXWS, and found it was melted. Light and fans were working. I had to throw out all that was in the freezer drawer. I called Lowes service and reported that our four-month old refrigerator wasnt working. They sent a food claim number and set up a service call. Then, the lady said to unplug it and plug it back in. We had since cleaned it out. I unplugged it and plugged after a minute and it came back on. The Ace service guy called to confirm his schedule. After hearing that it is running again, he said they are computer controlled and unplugging it and plugging it back in reboots it, as you might reboot locked up PC. He also said that since it is now running, Whirlpool wont stand behind a service call. He said wait until it does it again. Now thats just jim-dandy. We have an expensive new Whirlpool Gold refrigerator that has computer controlling that cant be trusted as the control may or may not lock up in the future spoiling the stored food.

I bought my Cabrio washer about 3.5 years ago. Little after the year, I had to replace the lid because the hinge broke. Then came the F1 code, which I noticed if you turn the machine off for a couple of minutes, it resets itself. About a week ago, it started making a grinding noise and staining the clothes with oil or grease. Transmission problems. I was told by the seller it had a 10 year warranty. I called them up and now I got to foot the bill for a technician to come to my house and tell me what I already know plus labor. Might as well buy a new one. Beware because I believe Kenmore is manufactured by the same company.

We purchased a Whirlpool (gas) range with double oven, in April of this year. We found that the upper oven over heats, on the right side, and therefore burns or bakes unevenly.The repair company will be out for the fourth time tomorrow. They have been very nice to deal with, but really have not been able to repair or come up with any definitive plan of repair action.

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.