I have had my whirlpool oven for approximately 6 years. This will be the 3rd time I have had to replace the thermal fuse. For the last three times I have used the auto clean, it blows out the fuse. It has cost me $110.00 each time I called my appliance tech to replace the fuse.

I purchased a new high-efficiency front load Duet HT Whirlpool washing machine (WFW9200SQ02) in January of 2008 for nearly $1000. I dealt with the mold issues and permeating smell for all these years, but the machine failed catastrophically this month - after just over 3 years - on a $1000 machine! The rear bearing went out. The parts alone are nearly $500 and the labor is estimated to take 3-4 hours by a trained technician. We are talking about an $800 repair --more than a new machine would cost. The most disconcerting part is to see how often this is happening. It is commonplace. The bearings go out on these things, sometimes after only a year or two, sometimes after 3 or 4; but it is very rare to have any machine go longer than 6-7 years. Whirlpool wont do anything. The best chance is forcing a recall related to the class action lawsuits pending about the mold issues, but by that time, how many people will still have their machines?

After yet another frustrating round of laundry I have to write this. This has been the worst purchase (Cabrio 6800 Washer and Dryer) Ive ever made. Like other reviewers, I thought I was buying a high-end (high priced) product that has performed miserably from day one. Clothes do NOT come clean and for some reason, towels and dishcloths get ripped and shredded. All cycles (except sheets/towels) do not dispense enough water. Of course the one that does, results in the ripped and shredded problem. A little more than a year after purchase, we got an error code indicating the computer board was bad. Code would come up during initial cycle start and again at the start of the rinse cycle. Whirlpool basically said tough luck but shortly after, we started receiving offers in the mail to purchase an extended warranty for $175. Out of principle, I did not do this. Instead we discovered that we could push pause/start/pause/start multiple times and it would eventually keep going. We are still doing that on EVERY load of laundry (start and rinse cycles). I am not far from just biting the bullet and buying a new washer. It will not be a Whirlpool. One positive note is that the dryer has performed well, unlike some of the other reviewer experiences!

We have a Whirlpool Cabrio mod. WTW5600 XW2, ser. C12830447 he... H2O.. low wash system. Less than two years old. It does not get clothes or towels clean. I put 2 jackets in on bulky items and part of one of the jackets was still dry. They were two small childrens jackets. My husband and I wash as long as possible and on hot wash (which is not hot!). Should not take 70+ minutes to try & get normal clothes clean!Now the softener is draining into the wash with the detergent. Another service call. Learned you can only fill the softened bin half full or less. WHAT??? Our extended warranty is up soon and not sure what to do. We would like to get rid of this pile of junk but cant afford another washer bill. Also wouldnt want anyone else to get stuck with it. Its a shame a company cant put out #1 good product and #2 stand behind it. Bring all of the company production back to the USA or put out a better product and stop worshiping the almighty dollar. Im done with Whirlpool (which was the product to buy), but stuck with this washer for now until we are sure that the brand we buy performs as it should. What happened to the PRIDE in & RESPONSIBILITY of making a good product and standing by what youve made. As my hubby has said, if you have to buy an extended warranty, whats wrong with your product! Again worshiping the almighty dollar or is it you just dont care about the people who buy your product or its quality. Maybe both.P.S. Have contact you before without a response.

I bought a Whirlpool washer (model wtw57esvw1) about 17 months ago. In that time, the same part has gone out three times. It happens every 5 to 6 months. The part runs 97 dollars plus labor. In the mean time, I am without the use of my washer. They say they are sorry, but they only cover their product for one year. After that, you have to buy their extended warranty so you can get it fixed by them. I feel that if I pay that much for a product I should expect at least 3 years without having to repair every 6 months! I have no washer. I am giving one star only because I have to.

Purchased a Whirlpool washer and dryer (WFW75HEFW0) in September 2017. Have had 4 service calls on washer for not completely washing clothes, leaving excess water after cycles complete, excessive wrinkling of clothes even on non wrinkle clothes, odor on some clothes due to incomplete water fill on some cycles. Factory position since there are no error codes washer is fine. Asked factory to exchange washer and upgrade model which we would pay difference. Denied. Looking for another brand and will seek legal assistance in the matter.

The first thing I noticed after purchasing this stove was that the glass top did not clean properly. I used the product given to me by Sears and tried several others but still could not take marks off of the glass top. I never really used the oven that much until retired and started baking often. The self clean does not work at all unless by self clean they mean that you yourself cleans -- I should say scrub it down. I previously had a regular self clean and it truly self cleaned. All I did was take wet paper towel and wipe out. Yet when I asked the Sears saleswoman about how it cleans I was told that it was terrific -- I would not have any problems! What a laugh!

I purchased a Whirlpool duet set on sale at Lowes about two years ago. The front loading washer has been leaking when I put in a full load of clothes. It usually floods the floor when it leaks. I am upset and very angry because this leak has ruined the doors to my washer doors. Apparently, the defects with this machine was known by Lowes and the Whirlpool company at the time that I purchased it (thus the sale price). This was not forementioned at the time of purchase. What a lousy way to do business. Whirlpool screwed me. Shame on me. Never again.

I bought a new Whirlpool fridge that has been a piece of junk since the day I bought it. The minute the warranty expired. The thing broke down. The corporate service center was a joke. 15 min wait time just to get through. Then a runaround of misinformed referral numbers. Minimum charge $200/30 min just to have a service rep even look at it. And then $100/hour + parts after that. Highway robbery. My doctor doesn’t even charge me that much. I will never buy a piece of junk WP product ever again. Their customer service is rude and non-existent. The company does not stand behind its products. Don’t buy!

Overall, I am happy with my Cabrio BUT we purchased a Whirlpool WTW7000DW0 Cabrio top loading washer w/ electronic touch panel in May 2016. We experienced water hammer from day one. I finally had enough yesterday and knowing that the plumbing could be suffering (15 year old condo), purchased 2 Sioux Chief MiniRester, Model 660-H arresters (Lowes at $9.99 each) and had a plumber install them today. I could have but am nursing a fractured rib. Long story short, they work perfectly. There is NO indication elsewhere in the unit that water is even entering the tub unless youre standing right beside it.Ive been told that hammer problems exist in ALL high efficiency washers, all are prone to this problem. I was also told by a Whirlpool support person that the Cabrio is a Samsung design and the pulsing of supply water off and on, over and over is normal operation. If I had been informed when purchasing that hammer is a common problem, I would have installed arresters from the get-go. At the very least, manufacturers should include arresters as a part of the sale; installers should make sure that every new installation includes arresters. All told, I am out just under $200.00 for new technology that really could have been engineered out in the beginning.

We have an 8-year-old built-in Whirlpool Estate. It is probably as basic a model as you can get. It has been 100% reliable, and cleans the dishes well, even without rinsing. We do not buy expensive premium dishwasher detergents, either. So far, we have required no repairs. Basic features--heavy wash, normal wash, pots and pans. This dishwasher is standard (not extra large.) This is not a fancy dishwasher--just white. It is what matches the rest of the appliances. We have been lucky regarding the performance of such an inexpensive dishwasher. We paid about $250 for it.

My wife and I purchased a Whirlpool Duet washer and dryer 5 years 1 month ago. We purchased the front load style because they were supposed to be better made than the older style. Its just my wife and I no kids. We never overload the washer or dryer. Now the drum bearings in the washer have gone out. I feel that a washer should last longer than 5 years and 1 month. I dont think I will be buying another Whirlpool.

I have never posted a negative product review but must do so now. The refrigerator is 1 1/2 years old at most and has been well taken care of. I noticed today that the finish at either side of the bottom of each refrigerator door handle has a problem. I couldnt tell if the finish was pitting or is just discolored. I called customer service and expected that they would help, especially since we have an extended warranty. Representative number one told me that the extended warranty only covers problems that affect the function of the product. I spoke to her supervisor and then her supervisor. I got plenty of apologies but no support. I offered to send pictures, but they were not even interested in checking out the problem.After speaking to them, I took the handle off and I see now that the handle cut into some sort of film that exists on the metal. (I am not talking about the protective plastic coating that is on the the refrigerator at delivery.) The film is lifting off the surface and creating discoloration. If Whirlpool was at all concerned, I think this issue could be fixed with some sort of gasket to keep the metal handle from cutting into the surface. Im hoping the problem is static, but hard to say what will happen. If they had been interested in trying to understand the cause of the problem, it would have been easier to accept the limitations of the warranty. It would have demonstrated an interest in avoiding this problem for other consumers in the future. My last Whirlpool product. Period. Good luck if you decide to do business with them.

The clothes have a stale and mold smell. The whites like tee shirts and shorts and other whites are a dingy yellowish color. The detergent that was recommended and pellets used every month do not work. I have called and complained several times and the operator said that she had one and it works fine, the other person said to wipe the inside of the washer and leave the door open after each wash and not to store the dirty laundry in the washer till next use. They never explained that you have to run a special pellet through the afresh clean washer cycle. Well, we have tried it every time and the clothes still do not clean and stink bad. We asked them for an exchange and they said no. Is there anything we can do?

We bought the set washer/ drier from Lowes in 2008. The first problem was that it wasnt rinsing well. After finishing the washing cycle, clothes were still dripping water. It took us to make several phones calls to get the problem solved. Also, the clothes were smelling bad and needed to be wash again. Now we are having another situation that it start the wash cycle but it wont finish and shows a code F35 or sud.

We purchased a Whirlpool French Door Refrigerator WRF989SDAHOO less than two years ago. The refrigerator runs constantly and has gotten louder by the day. It is so loud you can hear it when you are in another room. The temperature on the refrigerator is too cold and freezes fruit when I put it in. I contact Whirlpool online and they said it seems fine to them and also there is no temperature control that I can change myself. I am afraid I am going to come home one day to a dead refrigerator and spoiled food. I was not happy with their response and I WOULD NOT PURCHASE this again. The other problem is, we bought as a set, matching stove, refrigerator, microwave and dishwasher. So if I have to get a new fridge it wont match.

I’ve had this washer since October 2018. Worst purchase ever. It does not clean the clothes nor does it put enough water in it. I’ve tried the deep water option too and it’s for sure still not enough. I don’t understand how they even thought that this was perfectly fine to sell. If I could’ve taken it back a month after having it, I for sure would. And no one will buy it because they’ve read reviews of how it’s terrible. I wasted $900 on this washer. I have the dryer also which works amazing. The washer just sucks something terrible. My husbands military uniforms always look dirty and a lot of the clothes aren’t ever wet. I’ve finally seen a picture of how you’re supposed to have clothes in there. Why in the world would you only allow barely a layer of clothes at the very bottom to be cleaned by the agitator? Why would you have this huge drum only to put not even a load in there? This was such a waste Whirlpool and I’m glad I’m not the only person who has the same issue. I will never purchase another Whirlpool washer, it’s upsetting I can’t currently get rid of this crap washer I have now.

I bought model #W4TXNWFWQ at Lowes in February 2013. It had a one-year warranty. Five months after the warranty expired, the defrost timer went out. It cost $100 to fix the $400 refrigerator. Planned obsolescence or coincidence? Either way, its poor quality.

I call them. Lowe's gave me #. Spoke to man there at CS. He took care of me. I was a Lowe's within 30 mins. Gave them PO. Home within 45 mins. Whirlpool you the best in Johnson city TN. You're just like Lowe's. I pay for Whirlpool because you make it. Thanks for all you do. The best. #1.

This set of washer and dryer are very simplistic and have few options. They came with the house I just purchased and I think they may be 10 or 12 years old. I cant wait to buy a new set... Very soon!!

Spent the extra money to have a beautiful, slide-in oven. The AquaLift technology just seemed like another plus. After the turkey cooked, just seemed like another oven to clean. The AQUALIFT does not work, except for the bottom of the oven!! A fresh oven cleaner? Only available only. Get this beautiful range, not AQUALIFT TECHNOLOGY. CLEANING with it.

I purchased a Whirlpool Cabrio washer (WTW6500WW1) on 9/11/09 for approximately $800. Now three years later, it needs a new rotor and stator costing $470 in parts and labor. I called Whirlpool and was told I could get no help with the cost of parts because of the age of the machine! A simple Google search of the F51 error code that I am getting will show you that these machines are $800 pieces of junk! I am not repairing this machine. I am going to run it until it dies and simply buy a new washer. You can bet your sweet self it will not be a Whirlpool! I can only hope to inform enough buyers about this to keep them from the same fate.

I purchased the original Whirlpool refrigerator in August of 2013. That was replaced in October of 2013 due to a factory defect that left the ice maker unusable. In April of 2014, we now have a factory defect that has resulted in the entire unit unable to keep the fridge below 70 degrees F. It has been 2 weeks since the fridge died and Whirlpool has informed me it will be another 2 weeks until a replacement fridge will be delivered. I have spoken with countless customer service reps and 2 customer service managers, as well as 1 executive from the executive office in Michigan. Several times Whirlpool has dropped the ball in this process. The original repair appointments were booked and had to be rebooked because the repair company could not accommodate the appointment times Whirlpool booked. It took over a week to get the fridge declared dead. Then another week just to process the request through tech support... After speaking with 2 customer service managers and being told it was being rushed, I spoke with an executive who said the claim had never been submitted and it would take another 24 to 48 hours to process. I spoke with the executive after the 48 hours and he said the fridge will be delivered in 2 weeks! 4 weeks without refrigeration for a second factory defect. I have explained that I have a newborn (6 weeks old when this started) and a 2 year old, and we have had up to 9 people staying in the house (to visit with the baby) over this period and that I need a fridge to keep my breast milk cold. I was told I would receive a $75 gift card and a $125 check to help with food and costs associated with the loss of our fridge... Neither have arrived. We are spending quite a bit on ice just to be able to keep food and milk cold to temp. so we dont have to spend money on eating out (too expensive for us). I am shocked by Whirlpool’s poor customer service. The first time the fridge was replaced I dealt with one person and didnt have to call the customer service line every day. I wish I had her number still.

We bought the Whirlpool duet washer & dryer in the winter 2011. The washer is absolutely awful. I have to keep it set on the Whitest White setting so every load gets a second rinse. In order for my clothes to smell CLEAN I use bleach in every load I can. With the loads I absolutely cant use bleach in, I have to be standing waiting to put the clothes in the dryer or I have to rewash the entire load because of the smell!! My towels are ruined from the bleach and my clothes are faded because of the multiple wash cycles. I have used the recommended Affresh numerous times and it does not help! Needless to say this washer was a total WASTE of money! We will be purchasing a new washer very soon! It will NOT be Whirlpool!!

I had the first microwave for 6 years. My husband messed it up so got a new one, same over the stove type. It has lots of programs. Its a rather large microwave, plus it has a steamer which cooks vegetables with steam while I am doing the rest of the meal and whats more important is its quiet. The site is fantastic not just in width but in depth. The best thing about this microwave too is that it has a frozen cycle which does not partially cook the food like most microwaves and the defrost is the same, it does not partially cook it actually defrosts completely without cooking it. This is by far the best microwave I have ever had, and I wouldnt want any other brand. It might cost a little more than the usual brands but its worth it. I also have a mini Whirlpool on my Countertop for my grandchild to use so he keeps away from stovetop at all times.

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

I purchased a replacement gas range (whirlpool) approximately 3 years ago. Its not the top of the line, no bells or whistles such as a self-cleaning oven or such. I did love the three huge grates on top, one which is interchangeable with a flat grill. If it only worked it would be a decent range. The center oblong burner struggled to ignite in full from the beginning. Often, I light the thing with a grill lighter. But the thing that pisses me off more than anything is the F2 error that appears 70% of the time on the control panel when I am preheating the freaking oven. I am NOT replacing the control panel on a $400.00 range. What I have discovered is I can hit off my power at the main, not once, but 2-3xs and reset or over ride the damn thing. I read this F2 code is a common occurrence so I got to thinking, why? My conclusion is the heat from the oven is vented up & directly on the control board panel. Really now, whos bright idea was it to expose a control board to repeated temps of 350+? Hate this appliance. Next range will NOT be a new one, Im looking to replace this junk with something mom or grandma had that lasted decades, not a couple years. Shame on you Whirlpool for producing such low quality, disposable products. By the way, I just went through this with a new fridge so theres much to be desired with new appliances. Theyre junk, designed to fail.

After a days work Old Grumpy around 7:00 PM drags to sink, fills pan with hot water & soap; starts scrubbing forks, spoons & occasional cereal bowl. I prewash everything placing it in the dishwasher, it takes it a week to reach 3/4 full: use for sanitation.

Bought a Whirlpool standing freezer EV161NZTQ 10/8/2013. Been fine to a week ago and meat was soft, not frozen and veggies on door soft. Dont hear compressor cycling on and off anymore. Still under warranty so well see what repairman says. Things just dont last anymore. Last Frigidaire freezer lasted 10 years but they werent rated good by consumer reports.

We got a DEAL for this nightmare for nearly $700 back in 2014. Nothing but problems. Constantly finding plastic pieces at the bottom... some identifiable; others not. They are from the cheap parts within. The control board lights (all but 1 works) went just after the 1 yr mark. We are now having to replace the top Rack Adjuster (MORE CHEAP PLASTIC), as it has been barely hanging on for the last year and a half... constantly fighting it, as it would drop all the dishes if you moved it wrong.Now, the water is not draining at all... period. We clean this religiously - always rinse dishes completely, use rinse aid, never stuff dishes. Today we find a random plastic piece, which we are now trying to identify. NOTE: we dont put plastics in the dishwasher. So, today a new plastic piece and major drain problems. We are in the market and purchasing a new French Door Refrigerator and Front Load Washer. Will NOT be going with anything Whirlpool. Not much better these days, but this name has a big RED NO for us. Made it even worse when we contacted for help after that 1 yr mark. NO HELP AT ALL.

I purchased my Whirlpool washer on June 28, 2011. Within 4 months, I had to call for a repair. It is now going to be a year and I am on my seventh repair call. The repairs have been everything from loose pulleys, new belts, and new valves. When I called to complain, they said there is nothing they could do and I should take out the extended warranty. I have had washing machines last up to 15 years. Needless to say, they werent Whirlpools. I really would like to have it replaced. I dont think its fair to me that I should have to wait for a repairman to come out and tell me he doesnt have the part and has to come back. I did take out the extended warranty, which cost approximately $150.00 and that should not have to be.

My oven was a lemon from day one. The light bulb would not light, the oven would not come on. Had the repairman in cause it was under warranty, he replaced the gas valve. A month later the same thing happened, the oven did not light. Have been putting up with this for a little over a year, it is finally off warranty. Same thing happens, you go to cook something and it will not light, then the oven door broke! We had to pay to have a new hinge installed. Whoever heard of a oven door breaking? I have had ovens 40 years old and they still work and the door doesnt break. Needless to say, my oven is still doing the same thing, lights sometimes and other times does not. Called Whirlpool several times, they are nasty and wont stand behind anything. Customer service says there is no lemon law for stoves. I will not ever buy another Whirlpool anything and that is not a threat but a PROMISE.

I bought fridge model WRS571CIDm02. The worse company in the world. Since I bought this fridge have a consistent problem with the evaporator fan. It makes noise. Geek Squad came 3 time in 3 years to replace the same part. Now the 4th time I ran out of warranty and Whirlpool dont care. On top of that the stainless steel is rusting. It is not stainless steel. It is a nightmare. Avoid at all cost. If there is zero I would give it to them.

This Whirlpool Duet washing machine is the worst purchase we ever made. The first problem I had was that after delivery, the balancer broke and it had to be returned to the store. 3 months later, my computer board went out. I have to wash twice because my clothes are not clean. 2 months ago, my hardwood floor was almost ruined because water was pouring out the soap dispenser because a sock sucked in the rubber hose and stopped it up. Today, Im unable to use my machine. Whirlpool should recall this machine. It’s too expensive and not worth the money. I do not recommend Whirlpool and will not buy any Whirlpool products again and will replace all Whirlpool products in my home.

Sole owner/operator for 6 years using same products that came packed with dishwasher. Bottom rack has simply crumbled away, prong by prong at first and now large sections. Inferior quality of coating and metal used for the forms, means it wont withstand the daily use for which a dishwasher is intended. Worst quality control ever!!

I contacted Whirlpool in regard to one of their water heaters we purchased from Lowes. It came with a 5-year warranty. At the end of 3 years, the lower element went out. Our plumber took the part back to Lowes, where he stated they normally just do a part replacement with them. On ours, he was told the owner would have to contact the manufacturer. I contacted them and supplied them with the plumbers bill and copies of the front and back of our canceled check, along with all my contact info. Their website states theyll get back with you within two days. I contacted them on March 13, 2013. Today is April 7, 2013 and they havent emailed, called or snail mailed me. After reading these consumer reports, the air has been let out of my balloon. No more Whirlpool products for me! Integrity in our country used to be extremely high. Today it is extremely low as demonstrated by the complaints on this website and now mine. Hey Whirlpool, you suck!

On 02/25/13 we purchased a Whirlpool Gold Series side by side (French door) refrigerator with an ice maker at the cost of $1,850.00. In April of 2014 the ice maker stopped working and the freezer at the bottom would not freeze food. Luckily for us it was still under warranty and was repaired. At the time of the repair, the repairman (associated with HHGregg) told us that the refrigerator should have been replaced since the cost of the repair was more than the fridge itself. Now July 20th, 2015, the same issue has surfaced. Again the ice maker will not work and the freezer wont freeze. I would not recommend this product or if you do pay the extended warranty.

I have Whirlpool 25 in. Side by side. I love the space freezer size is bigger than the old one I had. Makes ice as it should. Overall solid appliance that I trust. I purchased this refrigerator a year ago after research.

Dishwasher (WDT710PAYM5) handle on the left side loosened within 2 weeks of purchase. Today the handle fell completely off. The dishwasher will be a year old in August of this year. I cannot figure out how to reattach the handle and there is nothing I can find in the owners manual to help me. There are only two of us and I am the one who uses the dishwasher. This should not have happened. Not real impressed with this machine.

This seems to be a very common complaint with Whirlpool French door especially after reading other reviews. Bought a WRF560SMY in 2/2014, from Lowes who installed it and promised good service for that first year. Whatever went wrong, they would take care of it, replace if needed, pay for lost food, etc. So far, so good. Now in 7/2015, warranty is up of course!!! And we are selling our home, so thought I would get an extended warranty as another selling point that would transfer to new owners. Well, of course, right after I purchased the warranty, the day after actually, the freezer started buzzing. Took a look and the whole back wall of freezer was covered in frosty ice. So defrosted it, seemed to run okay... For a few hours, same problem. It sounds like the compressor fan is scraping on ice, and it runs continuously. Defrosted again, same problem. So now it is time to break down and get on the phone, which I hated to do since I went through this with Samsung in late 2013, took me 3 months to resolve. Anyway, called Whirlpool Michigan office, which I recommend. They claimed they would cover repairs, and to call their warranty repair dept. to schedule service. THEY told me I was out of luck, as my just purchased warranty would not be good for 60 days. Back to Michigan, they told me it WOULD be covered, and to try again. No go, and this time someone with a middle eastern accent told me not only would it not be covered, but even after the 60 days, it still would not be covered as it was a, GET THIS!!! pre-existing condition! Excuse me, this is not a brain tumor, and Obama did away with that anyway. So tried to call Lowes, who sympathized, but could not help since the warranty I purchased was from Whirlpool, but they would repair if I paid. And be aware that most chain stores require you purchase an extended warranty within 30 days of installation, so out of luck there, but they were nice about it, told me go back to Whirlpool. So another call to Michigan, and FINALLY got a gal at their call center in Tennessee, who resolved my problem in about three minutes. All in all, 12 phone calls. This is a manufacturer issue. she said, not a repair problem. which is what the others were apparently not educated about. It appears, although she did not say so in so many words, that this is a very, very common problem, and Whirlpool will indeed cover condenser or defrost heater assemblies for 3-5 years depending on the model. So she is supposedly calling a local repair and someone will be out in a day or two, but will call us first. No call yet, so still nail biting. I would recommend to all of you with this or other issues to read the manufacturer warranty very, very carefully. There are some things in there that go beyond the standard year, and I KNEW I had read that this problem was covered beyond the one year, and indeed, it is. And also to call, call. Call their Customer Experience Center in Michigan (1-800-253-1301) and if your freezer is icing up, you will most likely get them to fix, depending on the age of your unit. If you dont get satisfaction with the first person, keep calling back again and again, and get the NAME of the person you have spoken with and tell them to document your call. This saved me, as every call I made came up on their screen so they knew I was getting frustrated. But, she assured me, this particular problem is ABSOLUTELY COVERED BY WHIRLPOOL, so obviously it is a defect they know about. Why they dont fix it at factory, dont know but will continue to look for that answer. They got especially cooperative when I told them I was purchasing a home that would need all new appliances in the near future, which is true. Use the Michigan number and keep calling and calling until you get satisfaction. This is a covered repair beyond the one year. By the way, I do not have my ice cube maker hooked up and never did, but still had this issue. With this being said, I am very unhappy that yet another refrigerator failed on me. The Samsung after only 3 months, and the Whirlpool after only 17 months. But I will follow up on this report when and if these repairs are made in a day or two ;-] we shall see, and let you all know. The repair service is Whirlpool certified, so will grill the guy they send and see how many of these he has to fix, and whether it really is fixed So stay tuned. Just dont take your time and get frustrated talking with people who turn you down right off. Be persistent, and plan on about a dozen calls and two hours of your time. Remember to take notes of times, names, what was said, etc. This is the only thing that saved me with Samsung by the way. After 3 months they told me they HAD NO REPAIR PEOPLE in my area, and sent me a check for the purchase price to buy whatever replacement I wanted, but they also made me jump through many hoops, send pictures, docs, all kinds of stuff. Think I can almost speak a mid-eastern language now as well. Not so with Whirlpool though. It seems most if not all of their call centers are in the USA. Good luck to all of you. On my way to defrost again so we can get some sleep tonight without the chainsaw noise, and will update as soon as something occurs here. Hope I helped a little. As a PS, the last gal I spoke with was so very nice and knowledgeable. I told her she should not be taking calls, but promoted to training the call takers, and did take the time to call her supervisors and leave a message at how very good she was, which we should all do if we ever get a nice, educated person on the other end.Updated on 07/29/2015: I promised an update, so here it is. After thoroughly explaining my issue, they promised and delivered a repair person who arrived within the time they gave. He was very nice, but even tho they knew what my problem was, the guy did not have the parts onboard. He said it may take a week or two. So I am defrosting my freezer about every 48 hours to keep it from totally destroying itself. To the guy who exchanged his Whirlpool for a Samsung, I wish you a whole lot of luck if something goes wrong, and it will for sure. You wont get anyone who speaks English, but if you have a Lowes warranty, you may fare better. I can give you details on what will go wrong and how they deal with it if you want. I would advise you to have the Lowes warranty, and not a Samsung warranty, and make sure you get one within 30 days, or you are out of luck with Lowes. Good luck to you. Will update more on my Whirlpool, will say the repairman was very, very nice and gave me his card to call if I had more problems I could not solve myself until the part comes in. By the way, I do not use the icemaker and never did connect it, nor with the Samsung. I pity anyone who has to deal with Samsung directly and strongly advise you to get the warranty thru the store.

This is Whirlpool model MVWP835DC2. I bought brand new. Recently used about once a week. Got an alarm that indicated no communication to core unit. Talked to Whirlpool service and unit is out of warranty (20 months) and advised I should use authorized service company to come and diagnose. This took 2 weeks. Service man came, washer did not power up. He quoted that repairs would be $750 and not worth it, buy a new one. I went on internet and found YouTube videos that showed how to diagnose and fix. I called Whirlpool for new console, $350 and one month. Went to parts house and got part for $250. This fixed problem.I have a few problems with this machine and company. 1) This now turns out to be a known problem with these machines. The console fails. I am not sure how this is going to last 30 years. 2) Service man took nothing apart and could not diagnose problem with no power. He quoted $350 for the console and the balance for the core. He was guessing or pulling a scam. Take your choice.3) Part not available from Whirlpool because so many are failing.Thanks for making a great product.

It shows handprints, smudges, the door swings open and slams into stove. I did purchase extended warranty which I intend to pursue, not enough space, door issue, junk. Dissatisfied, dislike, low quality - that should say enough.

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

Frontload Sport Duet ht: After just 8 years, bearing out on washing machine. Just had repairman out. Cost more to fix than what I purchased it for. I bought both the washer and dryer, thus the reason for the duet. So now I have a good dryer and lost its mate. I am not going to purchase another one. Very disappointed. I will not be purchasing any more Whirlpool products in the future. Off to the laundromat.

I originally brought this to the attention of Whirlpool on February 27, 2014, and they chose to ignore the matter I raised. I am appalled at their customer service, but then again, customer service has been dead in America for decades now. I purchased a KitchenaAid (Architect Series II, Model KERS807SSS02, Ser. XW4704146) oven in 2009, which included a 5-year extended warranty. The first time I had to use my extended warranty was the first time a pot overboiled and thus overflowed covering the top of my range. Since then, Ive had to have my oven serviced two other times, but resulting from a pot which overflowed on the range.The controls are located in the front, directly below the stove top. There is most definitively a flaw in the design of the model I purchased. It seems quite obvious to me that the design should have included protection from moisture reaching the controls. It is very common for pots to overboil, from time to time, and thus overflow, but this should not cause the controls to malfunction due to seepage. Had I purchased the model that had controls behind the range and controls above the cooking surface, moisture would never reach the controls when a pot overflows. It should not cost hundreds of dollars each time a pot overflows on a range. Had I known that the oven model I purchased had a design flaw that allows moisture to reach the computer controls of the oven, I would have purchased the oven with the controls above the cooking surface.I invested over $2K on this oven because having owned KitchenAid appliances in the past, the KitchenAid brand had historically proven reliable. KitchenAid (or now Whirlpool) can no longer take pride in the quality of their products, most likely relative to the loss of manufacturing jobs in the U.S. Whirlpool ignored me the first time I contacted them on this matter and most recently today when I was told that it was a use matter. Apparently they believe that an overflowed pot is not a common occurrence on a range. I wrote directly to Jeff Fettig, CEO of Whirlpool and he has chosen to ignore me.

We purchased this dishwasher (Gold Dishwasher WDF60SADB) because of its low 49-decibel rating. It goes over 60 decibels regularly and occasionally up to 70 during operation (not including drain noises which cannot be controlled by the dishwasher). We used a tablet app to confirm. Decibels are not linear, they are exponential. 70 decibels is what your average shower or dishwasher sounds like. 50 is about as quiet as a refrigerator. You have to talk over this dishwasher. And yes there was a big price difference between it and Whirlpools next loudest rated washer.Whirlpools customer service says they will not replace or repair based on sound ever, only for functional failure. Bottom line, dont pay any attention to Whirlpool sound ratings. They dont stand by them and do not consider gross overages a defect. Fortunately the retailer (Lowes) does stand by what they sell and will trade for any other machine by any other manufacturer. We have only good things to say about Lowes in this process. This machine arrived Wednesday, and we pick a replacement Sunday. It will not be a Whirlpool. I will never buy a Whirlpool anything again. We said it will do X but we dont care if a brand new one wont is no way to do business.

I have a Whirlpool oven and dishwasher and have had nothing but problems with them both since day one! Our oven went out Christmas and couldnt get service on it and we were entertaining for Christmas. DONT EVER BUY A WHIRLPOOL PRODUCT!!! If you do you have no one to blame but yourself.

Whirlpool has always been a quality product in my household. I had Whirlpool microwave prior to the one I recently purchased. It lasted 10 years and was used frequently and always on daily basis. It worked like a dream and I would never purchase any other brand!

The beat goes on. My Cabrio washer is still down. After working for a mere 14 months, the control board died, and the machine would not spin out water. The repairman ordered a new one. Though the part arrived several days earlier than predicted, the repair service said they could not send anyone out, until our scheduled appointment. At last, today, the repairman arrived. I am ready to start whittling down the mountains of laundry we have stuffed in every closet. Some areas of my house are starting to smell like a locker room. It is not convenient for us to haul everything to a laundromat, or impose on a relative who lives nearby.The repairman was in the laundry room for at least 45 minutes, and then very apologetically tells us that the part is bad. It will not work at all. He has ordered a new one, and requested rush service, which I think they will ignore. I cant help but think these parts are manufactured somewhere outside the USA. Well, listen to this Whirlpool, I would rather pay $25 more for this part, and have your washing machine work. Dirty laundry might seem unimportant to you. It is not unimportant to us! If you cant do better than this, make something else. I am furious, and will spread this news to everyone I know, and I will report on this situation again.

I bought a glass top stove model number W10221843A. My son dropped a plastic cup on the top of the stove. It put a hole and shattered it. Now remind you, it was plastic. I barely use this side of the stove, so not like it was weak. I paid a lot of money for this product just for a plastic cup to destroy it. Is there any recall on this stove? Any help will be appreciated. Thank you.

Problem of refrigerator is working good for a few days, then the freezer is all melted down for a few days, then back to working good again. Model: FD2560HES. Serviced on and by: 7/16/2015 - ** - told me the controller board is bad, need to order part. 7/23/2015 - ** - replaced the controller board. Resulting same problem. NOTE, which means my old controller board is as good as the new one. 7/30/2015 - ** - opened the freezer, back of refrigerator, told me the compressor is no good, gave me an estimate of total cost $817.86. I did not accept the proposal, and I did not agree the compressor is no good. I called and scheduled for service after and scheduled to have service on 8/4/2015. Then got called from the office, said, Cant come on 8/4/2015 and told me I have to pay the $95.00 first visit. So I called and spoke to the manager, then scheduled for next service.8/13/2015 - ** - when he came, the refrigerator is working fine. He said, Cant diagnosis the refrigerator, told me to call for service when it is not working. He said the compressor is good. 8/15/2015, early morning the freezer is all melted. I called, been told cant service the same day. 8/17/2015 I called the office (1-888-717-9322), requested to talk to the manager, promised to call me back. By this date 8/28/2015, still no call back from the manager. They are located in Michigan. I was told the local office address is: 9582 Katella Ave., Anaheim, CA 92804.

My wife and I bought a Whirlpool Cabrio washer and dryer set less than three years ago. And so far the dryer has been ok, but our washer has had to have a new motherboard and now it smells like its burning. Our last washer and dryer set was a hand down and was over 15 years old and never had any issues like our new ones do. Ill never buy another Whirlpool product again.

The Cabrio washer does not efficiently clean clothes! The clothes have a type of lint on them after washing, and our sheets have an odd discoloration that stays on them even after drying. We have a max. capacity washer/dryer, & we dont overload. Plus, we use the recommended detergents and the amount of detergent as directed. Fabrics dont even smell clean.

Whirlpool Duet Machines - I feel very fortunate as I have not had a single problem whatsoever with my Whirlpool washer and dryer and it is 5 years old. Never once have I needed a part or had trouble with it. I feel bad for those of you who are dealing with this as what is worse than a washer/dryer that does not work?

We have a Whirlpool washer wtw5640xw2, we have been experiencing burning wire smells for some time. We had bought the extended warranty. Lowes sent out a repair company. They replaced the main board and the problem has continued. This has been as intermittent problem with the burning smell. We experienced it this week really bad! I thought the machine was on fire. We called the repair company and they said they had fixed the problem. My husband called the Whirpool number and they said they would NOT do anything to help us. We are trying to get help from Lowes where we bought the washer. I am terribly afraid to use the machine. This model needs to be discontinued.. We bought this machine 5-07-12. If we dont get some help, we are going to our lawyer.

Washer is not worth the cost. After 4th year of use in a two person household the washer bearings are gone and require replacement. The washer sounds like an airplane. I was told based on my description of the issue that the water has leaked due to washing and spinning into the bearing assembly and has caused it to have friction. The Whirlpool warranty is just as costly as the machine.

Whirlpool Cabrio TLWasher purchased 2011. Doesnt drain, no spin, inconsistent cycling, poor washing action....wont even attempt to repair, in light of reading product reviews and consumer experiences with this washing machine- $600 junk.

I called Whirlpool’s 800 customer service line to let them know I was having a problem with this loud humming and rattling noise coming from my refrigerator because of a manufacturing defect (according to the service tech that came to my house to fix it). Apparently, the metal grid is being held by a flat mental hook which vibrates. What a loud noise. We cannot eat in our kitchen: the noise it terrible. The repairmans solution was to put a piece of rubber between the two metal pieces. It worked until he left. I told him it would start again and it did! I even let the customer service rep hear the noise and she agreed. I am in the early stages of my problem, but from what I have read I am not very hopeful. I would like to have the names and phone numbers of the people at Whirlpool who refused to help. Maybe if we would all band together and call them, they would get tired of hearing from unhappy customers and fix the problems. I am game. Anyone else?

I bought Whirlpool Cabrio washer two months ago (Model number : WTW7300DW0). They indicate washer use less water and clean better, but that is not true. Some clothes on top of the load were not even getting wet and clothes smell bad after washing. Even worse is that clothes got holes in many places and some clothes were totally destroyed after washing. In just two months, I have to throw away many of my towels and clothes. I dont believe this kind of washer should be sold again. This should be a recall to give us a replacement ASAP and remove any products still in the market. There are many complaints online, I hope someone will stop this and do the right thing.

This French Door refrigerator looked beautiful. There are only two of us in the home. We purchased it at the end of 2014 and it just keeps getting worse. The front of each shelving has cracked. They look like they are dried out plastic the way it cracks. The drawer tracks have seem to keep crumbling pieces off. This is not a cheap refrigerator by no means, this is the first time buying Whirlpool, and I believe the last time.

I bought a top of the line Whirlpool front load washing machine (WFW97HEDW0) and drier with my new construction house. After a few months the washing machine began making a loud, banging noise during the spin cycle. Then about a month before the 1 year was up the unit broke and dumped all the water in the drum into the catch pan it was installed on. I called for service and someone showed up in about 3 days. The tech opened the unit and found that the plastic/composite drum the spin unit was contained in split in half all the way around. The tech exclaimed he had never come across this issue and would report in what he found but that he did not have the part and it would most likely be a whole new unit but that its up to whirlpool to make the call. I would find out that whirlpool had decided that the unit can be fixed and they have ordered the part and would call to schedule the repair.A week went by, with no word. I called warranty service company, Via Services, and they tell me that the part is on back order and that it would be two more weeks before it would come in. Now were looking at being without a washing machine for a month. I communicate this to the builder and they somehow get whirlpool to come out a week earlier than they said they could. The day came for the repair and two techs take nearly 8 hours to repair the unit (how is this efficient?).After the repair the unit ran with an odd noise that I attributed to the way it was stacked. A month goes by and two days after the 30 day repair warranty I go to do a load of laundry and the unit turns on but wont run. I called for warranty work because it was clearly not repaired sufficiently. I schedule a tech visit which is for a week after. The day come and the tech says he cant fix the unit without charging me for the repair because it is now out of warranty and if I have the extended warranty then I need to set that up with the extended warranty group. I send him away because I had just paid for the extended warranty. I called whirlpool for the extended warranty work and they schedule a repair contractor to come out in 3 days.The repair contractor calls me directly to confirm if the unit is side by side or stacked. I let them know that the units are stacked and they say they cant repair it because its a two tech job and they dont have enough techs. They send me back to talk to whirlpool. Whirlpool then notifies me that because its stacked I have to either unstack it myself or hire someone to unstack it for me. Well, I cant unstack the unit by myself and why should I have to pay someone to unstack it when thats what the unit was designed for? At this point I am going back and forth with the builder to get a refund so I can replace the unit. I will forever steer clear of any whirlpool or subsidiary products. The products are flimsy and the service is no better.

I purchased a 30 gallon gas hot water heater from Lowes in 2013. Within the first 3 months, it went out. I contacted whirlpool who troubleshot the heater 4 different times. Final contact was in early 2014, I requested a tech to look at the heater. Was informed it is now over a year old, it would be at my cost. Replacement parts $30. Shipping the water heater is great if you like cold showers. After a little searching, I find they know this water heater is junk as does Lowes but dont care.

I purchased a Whirlpool 50 gallon gas hot water heater 3 years ago. I have 3 daughters all in school age. When my old one finally quit due to tank failure and out of warranty, I went to Lowes and bought a 6 year warranty hot water heater costing around $600. Now I figured you get what you pay for RIGHT! WRONG! So about 2 years ago the pilot light started to just go out on occasion, a bit of an inconvenience but there was no default code warning me of any other issues. So typically we just relight it. I called Whirlpool to get help with this issue, but they wanted me to pay for a technician to diagnose the problem. Um isnt that what the warranty is for? I said dont bother. Im not paying $150 for someone to tell me what I already know. Ill just keep relighting it myself. So finally the pilot light goes out for the 100th time but this time I go to reignite it and BOOM! It sounded like a twelve gauge shot gun going off in my face! Then it flutters flames into the chimney of the hot water heater. Scared the crap out of me at first. But it finally stopped and run fine. Well Im laying in bed a few nights later and woke up to a loud thumping noise, I go down stairs and it stops. The following day Im in the kitchen and THUMP THUMP THUMP BURP BURP BURP. Run over to the hot water heater closet and theres the flames shooting out of the gas valve into the hot water heater then BOOM! Its out! The valve unit finally took a crap I guess. I call Whirlpool again to get my warranty - this time it definitely needs to be replaced. So the guy tells me the parts are covered in the warranty but a technician needs to look at it first and the technician Ill have to pay.. Excuse me but what the ** did you just say? I have to pay for a technician to look at your failing part? No I dont think so! Just send me the part - Ill replace it myself. Im a millwright electrician by trade. I specialize in power plants and refineries. Im sure this little gas valve wont be a problem. I spoke with these idiots on a Friday and he said I could have it ground shipped for free and it should be here in 5-6 days or pay extra for quicker delivery. What the hell did he just say? I could pay extra for quicker delivery on Whirlpools faulty part? ** whirlpool should be saying Well have the part overnight to you.Now since it was a 3 day weekend theres no sense in me paying $40 to have it delivered 3 day because it still wouldnt arrive until close to the five day. So I just looked to see where my damn part is because it shouldve been here by now according to the guy on the phone. NOPE! Its set to be delivered in 5 more ** days. DONT BUY A WHIRLPOOL PRODUCT. THEY DO NOT PRACTICE ETHICS.

Whirlpool serviceman came out to see why our brand new dishwasher didnt dry the dishes and left pools of water on glass bottoms. Repairman said all the new dishwashers are like this. The heating elements do not heat hot enough so that the machine gets a higher efficiency rating. He said the solution is to use the dishwasher during the day and at the end of the cycle, open the door so the dishes air dry. My previous 24 year old GE dishwasher did a great job of drying the dishes even when we didnt use the heated dry cycle! The only reason we had to buy a new dishwasher is because we bought a new house. I am very disgusted with the Whirlpool dishwasher. Might as well do dishes by hand.

Wish we had gone online to check all the complaints otherwise we would have NEVER bought a Whirlpool model #EB9FVHLVS. Only 3 years old. First repair call to fix a manufacturers faulty grommet manifested by leaking in the bottom freezer portion. Just outside the warranty - did not purchase extended. Now I know why retailers recommend the extended. My sister overheard the repairman call in the product to his contact at Platinum Appliance Service Inc., and he made direct reference to the model number in the category of Whirlpool products known to have this specific design flaw, and that the product was never recalled but customers were directed to purchase a repair kit to fix the problem. Apparently this became a very well documented and repeated incident within the 1-2 year purchase date of these products and models with the known factory installed defect were still sent out to retailers at a reduced cost with no reference, warning or attention to the factory defect. Now 4 months after the first call we have to call in for another repair issue because our light in both compartments and the motor shuts off for hours at a time. We lost about $80 in meat products, so now were afraid to keep any costly items in the freezer because we cant afford to replace a $100 of thawed products every week on top of groceries already bought!!! It seems as though Whirlpool is gleefully generating business for appliance repair while making more than one hole in the consumers wallet.

I bought this stove 4 years ago from Lowes. I have had nothing but problems ever since. My family is now afraid to use the stove and Whirlpool refuses to stand behind their product. The last straw was a bill for a service call that took 6 months to complete without correcting the problem. Whirlpool sent me a bill for $100 to pay for the privileged. When I complained, WP said if I paid the invoice, they would give me a deal towards a new stove. Meanwhile, the old stove does not work and we are afraid to use it, given our experience with its reliability and safety. I plan to return it to Lowes and buy anything but a Whirlpool product. Beware of Whirlpool Maytag anything!! The customer service is shameful!!

My Whirlpool refrigerator is about 13 months old and the paint is peeling off. I was told my an associate at whirlpool that I could have a service person come replace it for approximately $500. And this is only for one door not both.

I bought a brand new KitchenAid stainless steel refrigerator for close to $3,000.00. It has a big crack in the back casing which Im sure is affecting the seal. It is still under manufacturers warranty. Whirlpool sent out a technician to put a yellowish plastic epoxy to seal the crack. When I told him that this was unacceptable as it dries yellowish and has a dull finish he explained that that was all Whirlpool was willing to do.I have been dealing with Whirlpool for 4 weeks now and they refuse to repair the crack and they deny any manufacturing defect. I have sent them pictures of the crack and they still refuse to resolve this issue. Very bad, horrible experience with customer service, long waits on the phone, rude and ineffective employees. This CLEARLY is a company that will not stand by their product and I recommend everyone to CLEARLY stay away from purchasing any Whirlpool products. They will be paying a lot of money for very poorly manufactured products.Please, please, do not purchase Whirlpool products! You will be happier spending money on a company that values you as a customer before and after the sale. Obviously Whirlpool would rather forget you after they have sold you their product and have their money. Thank you for reading this. I hope I have saved potential appliance customers from making the same mistake I made. DO NOT BUY WHIRLPOOL!

I am waiting for the third repair on my front-load washer. I purchased them a year ago and was very satisfied with the ease of use. But in April of this year, the E2F3 started flashing up after I put in a load of clothes. I called the repair line and they sent a guy to check it. Determining it was a sensor, I waited three days for the repair. Then, almost two months later, now, it did this again. He called WP and they said to replace the sensor again. I waited two days for the repair. Before he left, he started the washer to run through the cycle - no problem. I then put in a small load of clothes, and almost immediately, the washer stopped and the E2F3 was flashing again. I called for a repair, and am again waiting (without a washer) for the repairman to come back on Tuesday!!!Today is Friday. I have been four weeks almost without a washer this year. Thats also the $20 I have spent this last week to wash clothes at the laundromat, not to mention the frustration of waiting for the warranty line to pick up and the hassle of having someone here when the repairman comes. I am glad I purchased an extended warranty for this product, but Whirlpool should make their products to last!

In defense of Whirlpool, I will preface my question with the fact that I did attempt to call them and they were closed and Ive used manual to troubleshoot. Problem: when I cook any baked good in top smaller oven, the cookies, etc. on front of pan closest to door bake even and are not burned. All cookies on back half of sheet are burned and not cooked thoroughly. Any advice or similar experience to share would be so appreciated.

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

Purchased Whirlpool Washer Mod# WTW57ESV1 12/9/2011. Washers transmission blew on 1/20/2012. Requested Whirlpool replacement. No results. Will never purchase Whirlpool products again.

I purchased the machine December of 2010 from Lowes along with the matching dryer. I also purchased an extended warranty. A year ago July the lid on the washer broke at the hinges. I contacted the warranty provider and was told that the repair would not be covered under warranty and the damage was operator error. I purchased a new lid for approx. $250. One year later the replacement lid broke in the same location. I have tried to get a response from Whirlpool no response. I contacted Parts Select and inquired about changes that should have been made to correct the lids. He was not aware of any changes but did advise that the part had a new number which he indicated probably meant a design change. I ordered a new lid just under $250. New machines have a metal frame around the glass instead of the plastic frame which keeps failing. The springs that hold the lid in the upright position are so stiff I can hardly move them by hand. I am very disappointed in Whirlpool quality and consumer support. I will not purchase any more Whirlpool products.

Whirlpool 2 Cu. Ft. Stainless Steel Over-the-Range Microwave - My wife and I have just remodeled our kitchen and we bought all the Whirlpool appliances, fridge, stove and microwave. We have had them for about 3 weeks now and now the display on the microwave just stop working. I just cant believe this. Its going to be a real pain now to remove this and replace it. Has anybody else had this problem and I wonder if its even covered under its warranty.

I just bought a house with a Whirlpool Accubake wall oven and after I did a self-clean, the oven quit working. It goes through the motions of working but neither element heats up. After replacing the elements ($95), I am going to replace the thermal fuse to see if that cures the problem. Whirlpools automated Customer Service phone service sucks. You cant talk to anyone about troubleshooting any problems so you spend money until you eliminate all possibilities.

Whirlpool Cabrio WTW8500DW0. Like: Top loading, Handsome appearance, clear glass lid, easy access soap dispenser plus separate Oxi dispenser. Dislike: Does not have a soak cycle. We didnt realize until after we replaced our old Sears Calypso what a really poor job it was doing. It damaged the clothes and never really got them clean. Also, the small capacity made it nearly impossible to wash large items such as bedspreads or comforters. The Whirlpool Cabrio WTW8500 has be a delight.

Our countertop Whirlpool microwave oven is just over two years old and one of the led lights in the clock display just went out. The push-button opening mechanism is very hard to work and quite loud when the door is shut. When the timer is set but the start button is not activated for a few minutes, the door warning goes on and you have to reset the timer. There are five beeps that indicate when cooking is done and they continue even when the door is opened. The only way to stop them is to push the stop button and there is no way to adjust the noise level or number of beeps.

Do not buy this washer. It does not get clothes clean. I use extra rinse (that negates the water savings) and still clothes comes out with stains on them. Some clothes are not even fully wet when removed after washings. I find myself soaking and pre-treating many items. White socks and undergarments are grey soon after buying. I always liked Whirlpool washer and dryer products, but this is a very poor product.

Whirlpool Microwave model #GMH5205XVS0 - Same story as many of these other reviews. Similar reviews on Amazon as well. We bought a new house early in 2011 with all Whirlpool appliances. We have gone through 3 magnetrons in 2 yrs. Now Whirlpool wont do anything for us. We will have to buy a new microwave. It just stopped heating all 3 times and the magnetron was replaced. Now it has happened again. Ridiculous. I will never buy a Whirlpool appliance again. This model # should be recalled. Its a lemon and sounds like it could be a danger as well.

2 loads of clothes and it is broke. I tried to call Whirlpool to no avail. So I called Costco where I bought this machine. They at least talked to me. Promise to get a hold of me tomorrow. Brand new (2 days old) and this happened. Didnt even finish the second load.

My washer worked less than a year. I finally called Whirlpool and they basically said, were a big company and you must for the rusty, broken drive shaft, pay for all new computer face plate, and service repair. I contacted the FTC and they told me they needed more complaints in order to make them do a recall on Cabrios. Good luck!

We purchased a new Cabrio top loading washer in June of 2011 to replace a Maytag Neptune (thinking at the time that wed gone as low as possible). We didnt abuse the machine. In fact, because it had a tempered glass lid (in a plastic frame), we were careful with the lid on the machine. It broke during a wash cycle. Because its heavy, the lid has spring supports on both sides; these are stronger than the plastic frame and over time the frame will break, rendering the machine inoperable. The discounted price for a new lid is over $200, and Maytag (I mean Whirlpool) tells us that it lasted through the 365 day warranty, so the bill is on us. It may be green when it works, but taking 18 month appliances to the landfill is not very green. And others on the web report say that the lid only lasts a year or so. The ratings scale needs to have negative values. Id give this appliance a -5.

I bought a Whirlpool Duet Front Load Washer in 2008 and it began showing F71 and F70 error code in 2011. I paid approximately $1,000 for the machine. The washer wont finish the cycles and often wont start. When I press the power button, I hear the 3 beeps and after a while, shows the F71 error over and over. The information I gathered online indicates that many people have the same problem. The repair cost is at least $550 to replace the user interface circuit board and is no guarantee. This is ridiculous.How could GE sell consumers this kind of junk that fails to work only after 2 years. I had a top loader for 12 years with no problems, not a single repair call. My wife and I are extremely frustrated with piles of dirty clothes and no washer to clean them. I want GE to refund the cost of the washer on a 10-year prorated basis. This is only fair.

Owner of 20 apartments, 16 of them have electric water heaters and 4 have natural gas units. Have replaced over the years all 20 water heaters. 19 of them were replaced with Whirlpool units bought at our local Lowes. It is my opinion that they are very unreliable. The tanks rust out in NO time. The electric units last just a little better than the gas units but still terrible. Of the 4 gas units so far I have had to replace 3 of them and the longest one lasted 6 years and 7 months!! One of them was just over 6 years and the other was 9 days away from warranty expiring. They replaced that one. If you have no other choice make sure to buy extended warranty if available. They just dont last!!

Purchased a Gold Series Whirlpool dishwasher, Mo. No. WDT720PADW2, From Maruszcak in Schererville, In. on 1-29-16. Approximately a year later door was replaced by Whirlpool because of paint problem due to faulty design. Replaced door is now peeling and rusting by exhaust vent also. Contacted Whirlpool and they will do nothing more. They said it was a favor the first time they replaced the door. They feel this is a cosmetic problem! I paid a total of $675.03, Their repairman would charge a $100.00 to look at it and another $235.00 for a new door. I feel this is a design problem and they should replace it with a new model, a refund would be better. Very unlikey, because Whirlpool does not stand behind their products. The line also includes Maytag, Jenn-Air, Amana and Hot Point. Besides this I have found plastic pieces that have fallen off! I had to use plastic ties to keep them in place. Dishwasher does not clean well. Have to rinse everything first. Products are bad, stay away from them!

I would like to share whirlpools lack of ownership for parts they knew were faulty that caused significant damage to my floor. Its absolutely horrendous that one would purchase the highest end dishwasher they offer (all highest end appliances in 3 homes so far) and the company is only willing to cover the replacement of the part. Its a horrible way to run a company. I hope that my review will warn prospective customers to stay away from a company who is only willing to take your cash at purchase (charging an arm and a leg no less) and not care about any repercussions after the fact. I hope they enjoy our 15k, because it will be the last penny they get from us.

I bought a Whirlpool Cabrio Top Load washing machine September of 2012. It has never cleaned the clothes well. For the last month the machine has a very loud spin cycle. I am very unhappy with this purchase and it is 2 months out of warranty. I emailed WHIRLPOOL and was told that all appliances have problems and wear out. WOW! It is 14 months old and has been used with care. I will never buy another Whirlpool product.

My Whirlpool French Door refrigerator will have its TWO year old birthday on September 15, 2015.. only if it lives that long! On August 8, one month and one week short of its 2nd birthday the compressor died. Of course the manufacturers warranty expired after one year. Thankfully, I purchased an extended warranty through the retailer. While this will cover my repairs, there is nothing that will cover the hundreds of dollars worth of spoiled frozen and refrigerated products which had to be discarded. I will NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT!

In 2008, I purchased the 40-gal. Whirlpool electric water heater to replace the original unit in my home that had lasted 14 years without issue until it died of old age. After about 2 1/5 years, it died and I was given authorization to return it to Lowes at my insistence. Now after another 2 1/5 years, this one has died. So far, I have replaced both elements, lost a days work, missed out on a date because I could not take a shower and now Im told I have to replace the electrical box on top which wont get here until Monday. Its Saturday and I havent been able to take a shower in my home for 5 days now.The first CSR (Crystal) I spoke with implied that since I had 2 consecutive failures, this was a site problem, not a product problem. Theres nothing special about my site, and my old unit made it 14 years with zero repairs. I would argue that since both of the units only lasted 2 1/5 years, that the product is substandard. I asked to speak to a manager but was told no because they were all busy (no doubt) and her demeanor was unapologetic and unsympathetic. The second CSR (Nick) I spoke with was very nice and at least sympathetic. That goes a long way in customer service, but I was still not allowed to speak with a manager.I am going to try and repair it one more time, but I have zero confidence in Whirlpool and would never buy another Whirlpool product of any sort again. If I get it working, and after all Ive read here I doubt that I will, I will only be using it for the time it takes to get a replacement of another brand. This was my first experience with a Whirlpool product and you can be sure it will absolutely be my last.

Bought a higher end Gold Series French door refrigerator. Immediately the door would malfunction and the the piece that pops out to seal the gap between the 2 doors kept piping out when the door opened...They came out and replaced it which did nothing...The repairman said we have to open the door slowly...Give me a break...Have a older cheaper model that is almost the same and its always been flawless.Now in year 2...the whole system shuts down out of the blue and thaws everything then suddenly works for a few months...Repair guy says cant do anything if he doesnt see the problem...Just got back from long vacation...We turned off the ice maker and emptied...Returned home to damaged wood floors and a bin full of ice...System reset when it restarted and started making ice...2 years old and we have a Samsung on order and the Whirlpool is going in the trash...Weve had many whirlpool products and the defects are getting worse every year...Absolutely done with them!

The washer worked well the first year and has gone downhill since. There is mold on the rubber seal where the door closes. This was supposed to be a recall and was never sent the replacement part. We have to constantly use bleach to clean the rubber.

We purchased the model WFC7500VW, 24” washer and accompanying dryer in June of 2015. Within a couple of months, the water pump went; also we continually had to take the front panel off and clean out the filter when we get an A11 code! Now we experienced an F06 code... This code means the washer can’t go into high speed. The repairman (Whirlpool recommended), told us that a new tachometer motor, etc would run $500-$800 with labor! He also said that the noise the drum made was bad. My dryer works fine (only complaint is the grinding noise it makes, which Whirlpool told me is normal)... I would like to purchase a new washer, but don’t know what will fit under the dryer. I do not want ANY Whirlpool product!

I have had my Whirlpool gold series dishwasher for approximately 10 years and it still does a great job washing my dishes. Recently, I found out if I forget to put a dish into it I would have to start the dishwasher all over again rather than it taking up where it left off. Also, the interior is badly stained and unable to clean it.

I purchased this washer about a year ago and have been dissatisfied with its performance since Day One. It takes a long time to run a cycle and has not saved me any water or electricity. I always have to add a second rinse because it doesnt get the soap out (using the recommended detergent) with the regular cycles. Sometimes it doesnt get my clothes clean.Today it tore huge holes in the front and back of one of my very favorite T-shirts, which was a very meaningful gift from a very good friend. This was due to its tangling the clothes even more tightly than it usually does; the tangling process was what tore the material. I always take pains to load the machine in the manner instructed, to put the clothes in loose balls around the outside of the drum, but nevertheless it can take me several minutes to untangle my laundry before I put it in the dryer (also a Whirlpool -- just waiting to see how it disappoints). If I had read the reviews here before I selected my new machines, I would never have purchased the Whirlpool washer or dryer. I certainly never will purchase Whirlpool machines again.

I purchased a Whirlpool Cabrio on October 27th, 2010. The Cabrio is always giving me the UL code, which indicates the load isnt in balance. Ive been doing laundry for 27 years. I know how to load dirty clothes into a washing machine evenly. Sometimes it will take me all day to do one load of laundry! Seven months after my purchase, my Whirlpool Cabrio washing machine started giving me the F51 error code. I called the phone number on my Lowes receipt for warranty work. Two weeks later, I finally had my washing machine running again. I was happy and thought Id only have to deal with the UL code. Boy was I wrong?!Now Im two weeks away from my warranty expiring. Im getting the F51 error code again! This washing machine is an $800 piece of junk! Hopefully, I can get the Cabrio repaired before my warranty expires in two weeks. I do a lot of laundry. We are a family of six. So, I know Im hard on washing machines but come on. Shouldnt an $800 washing machine last at least two years? Im not even a full year into owning this junky washer and Ive had two breakdowns! In my opinion, this washing machine needs to be recalled and people need a reliable replacement or refund.

When we bought our side by side fridge (model GD5RVAXVB02), the manual said to clean the condenser coils if you have excess dust and/or pet hair. We have both. We tried with the vacuum and with a brush but it is impossible to get to the coils because they run side to side instead of front to back. You can only get to the first coil in front. The rest cant be accessed from the front, sides or back. I called to find out how Whirlpool recommended they be cleaned and they could only recommend a vacuum attachment tool (8171579A) to clean the floor below the coils or a coil brush (4210463RW) that cant reach the coils! This design is meant to fail prematurely. They could have easily installed the coils running front to back so they could all be easily cleaned.

19 gallon Electric Whirlpool water heater Model #e1f20us015v - Purchased this water heater from Lowes to provide hot water to small apartment with no kitchen for my son, built in my garage. Had unit professionally installed within 1 foot of bath to provide hot water for shower and sink in bath only. Hot water lasts only 5 to 6 minutes and takes approx. 2 hours to recover. My son cannot even take a normal shower! ntacted Lowes who was unable to help and told me to contact Whirlpool. Contacted Whirlpool after my model number would not even come up on their website. I asked tech what was the normal expected amount of time before hot water depleted. She did not know. I asked what was the normal recovery rate. She did not know. I asked for information on the energy rating. She said there was no information available. I asked how I could receive a refund. She said that they could only send a plumber to check unit and that nothing would be done if it was heating water. I asked to speak with a supervisor. She said none were available and said one would call me. I never received a return call. VERY DISSATISFIED with Whirlpool on this issue. It appears my only recourse is to purchase a new water heater and scrap the present one.

Horrible. We purchased the set In October 2010. It worked great for a little over a year. (Go figure, just out of the manufacturers warranty.) The washer stopped spinning out water. Every other cycle completes successfully. The diagnostic cycle is also successful but once there is clothes in the machine, it wont spin. I called customer service and was told that a one year warranty was $230 and service is $130 plus parts. After reading another horror story, it seems that this venture is going to cost us around $450 for a new circuit board. Where is that class action suit at again?

The 12 year warranty, means nothing. The heater only worked for 30 months, and then its upper sensor fault code flashes, and the heater shut down. I called Whirlpool, and they have me use an ohm meter to help troubleshoot the problem. So if you are not handy, you are out of luck. They decided it was my control unit that is defective. They will send me the part free, but I have to pay shipping and installation. What a deal, and what kind of management would dream up of this. The heater is marketed as a 12 year warranty model (only on the tank). Would anyone, having been through this, buy another Whirlpool product?

Model gmh61xvb1 was purchased about 2011 and has had to be fixed 5 times. Now, its down again. My GE microwave lasted 23 years. I thought Whirlpool was supposed to be the best. Boy was I wrong. This has been a real headache. I ordered an LG yesterday. I was in the market for a refrigerator but it will not be a Whirlpool. What has happened to your quality control?