After 3 short years, my dryer that cost me over $900 is not working and the part needed for the repair is no longer being manufactured. They did offer the parts for free, but that was useless since they arent available. They then offered me a new dryer which would cost me $800. I am currently waiting for the Product Exchange Team to contact me. Im not hopeful that will be of any use.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

I bought a Cabrio set in June 2007. Within two years, I had to have the barrings replaced ($800 job). Now, its two years later and Im getting a F50 code. The repairman put in a new part, still got the same code and left. I am out $970. I am a disabled vet/single parent and now I have to buy a new washer. Who is going to start the class action suit against Whirlpool?

We purchased 3 Whirlpool Gold appliances, fridge, range and over-the-range microwave in 4/2011. Since that time, the fridge needed repair, the microwave door had to be replaced and the range had to be repaired. Now the heating element on the microwave went and Whirlpool will not fix the problem. We purchased the extended warranty through Whirlpool and they are saying it is not worth fixing. We paid $470.00 plus tax and install and now all they are giving us is $348.00. Since we have had repeated problems with these appliances, why not just fix the problem or replace the microwave??? What Whirlpool customer service told me was that would be options for us if we did not purchase their extended warranty. Tell me, is that fair? The cost to repair the microwave was $388.00 and they are giving us $348.00 - do you not think for the $40.00 difference, it would be worth to spend it to keep us happy. We will never purchase another Whirlpool product again and will tell everyone we know not to buy their products.

Whirlpool front load washer was not working. I waited two and a half weeks for parts. The parts came but they cant fix it. I waited for answer for two more weeks. They decided to replace. After waiting two more weeks, no washer. Its going on eighth week, still no washer. Theres no reason we have to wait so long after paying for the extended warranty in this day and age, and paying good money for the washer.

We purchased our first front-loader washing machine (Whirlpool Duet WFW9250WW00) just over two years ago. Since we purchased it, it has torn clothes and we have replaced the drum baffles twice (this would be the third time, but we are throwing the washer out), the drum seals twice (another place clothes can get caught). I had adjusted my washing (maybe I overfilled the washer, maybe I was using the wrong spinning speed), but every so often clothing would come out with holes or torn. The drum baffles must come loose before they come out, and clothing can get caught underneath them (I think that is where the tears occur). It has happened at least once a month and I had spent a fair amount of time trying to figure out where the clothes got caught and torn. Many people complain about bad smells from the washers (which I never had - I like the Tide with Febreeze detergent and every so often clean it with bleach or Affresh), but never torn clothing. I would really like to use a front-loading washing machine, but we are going back to the top loader - we cannot afford the clothing tears. I have seen that many people replace baffles (not many speak of clothing tears) and maybe in the future this problem will be addressed. But in the meantime, I would stay away from Whirlpool front-end washers. (GE makes some nice top loaders - and in 40 years of washing clothes and only owning two other washers, I have always thought washers to be an appliance that would last 15 years or longer with very little maintenance or trouble). I believe that I really tried to make this washing machine work out, but it got to the point where my husband did not want to wash baseball uniforms and other irreplaceable clothing in our washer.

We bought all Whirlpool Gold Appliances when we re-did our kitchen 5 years ago -- fridge, d. washer, oven, glass top stove, and microwave. Recently I noticed a pool of water in front of the fridge. Turns out there is a sticky grommet problem that prevents moisture from draining into a pan on the inside back bottom of the fridge. Whirlpool will send you a replacement part that is totally different than the original poor design (a long hose affair) BUT wont pay for the labor to put it in unless the unit is less than 2 years old.I watched a video showing how to do it, but it looks pretty tricky and involved plus risky because you can break the drain pan in the process. Spoke with a Whirlpool rep and a supervisor -- both admitted to a quality problem but got nowhere on the labor. Theyre sending the part, and the supervisors supervisor is supposed to give me a call, so well see if they eventually do the right thing and cover the labor. I mean cmon... the parts obvious a bad design, or they wouldnt be sending a totally redesigned part! Covering the labor only if its two years old or less? Even the Whirlpool techs online are saying the problem happens after about 4 years! The grommet gets sticky and wont drain due to heat from the compressor, and that takes time to happen. Ill update this when I hear back from Whirlpool.

I have had trouble with this AccuBake stove since four months after I bought it in 2011. First, the clean cycle would work intermittently then would not ignite to bake, broil warm or clean. All burners would light intermittently. Every time I had trouble, I called the service tech from Homestead Lumber, where I purchased the product from and he could never find anything wrong. Product would work fine whenever he came out. Finally, it acted up in May of this year while the product was still under warranty and while the service tech was here. The tech replaced the circuit board. One month later, Im still having trouble replacing igniter. Four days ago, Im still having trouble. This stove stinks. Right now, I wish I had my $959 back for the stove and wish Whirlpool had it stuck up their butt.

Bought a built in oven August 30, 2018. Oven stopped heating two weeks before Thanksgiving. Repairman fixed it. It is not working again, two weeks later. Bought from Best Buy. They will not take it back. Whirlpool will not replace it. UGH!!! $ 1,600 down the drain. Will no one help?

I stumbled across this site while browsing the Net, looking for a way to deal with the same situation I now know you all have been struggling with: Whirlpool Washing Machine! I wonder: Is NASA still accepting volunteers for their living on Mars experiment? Id rather beat my clothes on a rock than touch that POS Whirlpool that has me back on tranquilizers! Mine was purchased about 2 years ago when I was in bad health and my son was handling my affairs. I could tell - just by listening - there was something very wrong with it, from the first load my son attempted to wash. It would start and stop, restart, restop, ad infinitum and made a terrible racket. I told him nobody would intentionally make a machine like that--something had to be wrong with it but he assured me that he had checked both with the store that sold it and he also read the manual. He had a hard time accepting but we thought maybe this was because it was new and would settle down after some use; after all, the store (Best Buy) assured him the sound was normal for this particular machine. However, the weird sounds did NOT lessen nor stop, nor did the starts and stops. Little did we know, this was just the tip of the iceberg! We have encountered/suffered through every nasty performance detailed here: low water, wont spin, leaves clothes soaking wet, wont spin out excess water, lid locks (grrrrrr), it cant seem to switch from one procedure to the next; there is nothing washing the dirt out of the clothes--they just sit in the water and soak(?), then the water is released. Clothes come out with stains still on, so wet that the water must be wrung out of them! Very hard for me with arthritis all through my body! Ive tried countless times to reset machine to Drain & Spin. Ive even waited (yawn) for it to unlock so I can open and then readjust the heavy/wet laundry, trying to make it even all the way around so to avoid an unbalance. But nothing helps. It will start to spin. And then it stops. (wait, wait) Starts to spin again. Stops. (wait, wait) Starts again, does it a bit longer. (start to relax) Stops. Ive spent HOURS engaged in that kind of mindless, maddening frustration, just trying to wash one small-medium load. (I wash only for one person--myself, now.) My son, who got married and no longer lives with me, said the only way he could manage to struggle through it - and agrees it DOES take an inordinate amount of time--for just ONE load, he has to put the settings so that it washes in Deep Water even if small load. He sets Rinse, to 2 Rinses. He sets it to Soak even if the soil is light. Even then, it still makes noises, starts and stops, has to be adjusted several times during Drain & Spin. Last but not least, the noxious odor: OMG! I left one batch of laundry in the machine, with the lid open, as it was very late so figured Id dry them next morning. Some hours later when I went back to shake them out and put in clothes dryer, they smelled so awful, I had to wash them all over again! In fact, Ive had to follow my sons admonition to leave the lid up AT ALL TIMES unless actually washing in order to keep down the stink. I washed my last load with Baking Soda added to wash cycle in an attempt to lessen the odor and get laundry cleaner. Someone here wrote - in their review - that there should be a Class Action (Law) Suit filed against Whirlpool. I AGREE!!! And I want to opt IN on it. There are several law firms that advertise on t.v. that specialize in Class Actions. It would take some time and paperwork but will not cost us anything unless we win the case. Then the law firm gets a percentage. I am willing to work with one more others here who truly want to settle out this problem. I cant believe 2,000 (and thats only here), people are willing to eat hundreds, thousands of dollars of worthless, mind-gripping, rubble such as we have spent our hard-earned money. Other manufacturers recall their defective merchandise and/or replace it, or make arrangements with the retail stores who carry it to make amends, free repairs, whatever it takes to make dissatisfied, disenfranchised customers, whole. We paid for these demons from hell and we deserve to get an equivalent in merchandise (that works properly) or services. That is how it is done here in the U.S. For the life of me, I just cant comprehend why Whirlpool has been allowed to continue selling this junk--why no entity or person or lawsuit has stopped them! As I said, I am willing to work with a core group who is serious about filing a Class Action (Law) Suit against Whirlpool. It may be that the retail stores would be included as well; however, that is a matter best left to the discretion of whichever law firm we select to represent us. For those of you here who do NOT wish to be included, do not worry; you are not being pushed into anything. The way Class Actions work, you have the choice to opt IN (be included to receive your pro-rata share of what is collected). Or you are completely free to opt OUT. By opting out, that means you do not wish to be part of the Class Action and therefore, you will not be included nor will you receive any portion of the recompense collected via the Class Action. Just for your information, though: You are allowed, by law, to bring your OWN lawsuit against all or some of the same parties. The most common reason for opting out, is if you have suffered an extra large financial loss and prefer to file your own suit in order to collect ALL recompense; whereas, sometimes - in a Class Action - the individual plaintiffs may not recoup the total amount they feel they have lost. If you DO decide to opt out and go on your own, realize you will be fully responsible for lawyer fees (although you CAN add them into the balance you are seeking in your suit. Settlement of your claim may or may not include lawyers fees.) Good Luck to all. To those who wish to file a Class Action with some of the rest of us, please contact me if you want me as part of the core group of plaintiffs.

We purchased this large 4 door refrigerator in December 2018, from Costco in Florida, having in mind with the 2 years Manufacturing warranties and 2 years of Costco warranties above the manufacturing warranties. We didnt expect any problems for the initial 4 years. Up on delivery some parts of the unit was missing, delivery guys said they will make a report for the missing left drawers and the parts. We did not have any manuals how to setup and use. After we called the customer service they send us the operating manual.We encounter several other problems with this unit and the most recent one to our surprise the warning light to change the water filter was on. We hardly using the water from the fridge because of the having monthly spring water delivery service. We called customer service and after explanation of our concern and following their instruction the light was on. Finally we were told that whether or not using the water filter has to be changed every 6 months and send us the additional service warranty contract which is $411.95 for 3 years. We still have 3 years 4 months remaining from our original warranty.

3-4 years ago, I had replaced my hot water heater with a Whirlpool, which was purchased at Lowes. On 10/23/11, I awoke to a flooded basement from the said water heater. When I entered the basement, I was able to verify that the water was spraying right from the casing of the unit. Who knows how long it had been spraying, but the place was a complete mess. The water was about 10 inches deep and many things were ruined. I proceeded back to Lowes and purchased another exact unit. This morning I awoke to the sound of what seemed to be water bubbling, only to enter the basement and see exactly what I saw just three weeks previously... another flooded basement from water just pouring out the side of the unit. This is an obvious defect in craftsmanship. Now I find myself with a flooded basement, no hot water, and a decision to make. Do I fight for another replacement or give up on the brand? A replacement water heater will solve my lack of hot water but for now, the question is for how long? Not to mention the cost and time spent with the clean up I did twice.

I have purchased many Whirlpool ranges for my apartment buildings that I own and operate. They never give me a problem with operation or length of service. I only have to replace them when a tenant does something dastardly to them. My husband and I remodeled our kitchen and we purchased one for our kitchen too!

My Whirlpool has been in use about three years. It was purchased on sale at a very reasonable price. My only complaint is the heat dry function which somewhat fulfills its purpose, but I usually have to hand dry some dishes. Overall, it is an average dishwasher that gets the job done. The best feature is that it is very quiet; you barely notice that it is running.

Bought this machine June 23, 2016. First use, I called Lowes where I purchased it to say there is something wrong as it makes a grinding noise. I was informed that is normal for agitatorless machines. I asked if he could hear the noise, and he said yes, thats it. So I disconnected thinking, Wow, who makes a machine in todays technology that is so loud you think something or someone is in serious pain?! Now am at the point where I want this design in pain out of my house! Going to Lowes today to try and talk rationally for a complete refund so I can purchase an LG or Samsung which is what I should have done originally.

Moved into a house with a 2009 Gold Series Dishwasher model GU2475XTVY0. It has never worked since we moved in 3 years ago, always left dishes musty and poorly cleaned. We basically used it as a rinse/dry and pre-washed everything by hand. Even then it would mold up frequently and required manual cleaning. Total piece of junk, but looked really nice, stainless finish. Yeah.Latest chapter is it completely stopped working. Called a tech out for the usual $80+. His advice: this is a total lemon, and has been from the start. Not worth repairing. So Whirlpool, is this the standard you have now? 5-6 years for a dishwasher life cycle? Noted that my fridge is a matching 2009 Gold series, it has also had several problems with keeping a steady temp and has gone through 2 control boards at a hefty fee each. I guess Im done with Whirlpool, running out of appliance brands to blacklist here...

I purchased this machine from Sears on 04/23/2016 and have had nothing but problems and issues with it. It is loud and makes different sounds every time I use it. It has overfilled and underfilled with water a few times, the machine shuts down while washing and I have had to restart the machine. Half the time the clothes come out covered in soap and I have to put them through another rinse cycle. My bedding always has to either go through a second rinse cycle due to being covered in soap or I have to rewash it because it is all packaged together in the fitted sheet and never got washed. During the spin cycle it sounds like it is getting ready launch into outer space and it vibrates excessively. On numerous occasions I have had to untie my clothes as they are tied in knots. There have been times that I had to put the clothes through another spin cycle because the clothes contained too much water. The final straw was last week (03/27/2019). I washed my sheets and they came out bundled up in the fitted sheet full of soap stains and I had to rewash them. When the sheets were done I put the comforter in the wash and started to clean the house. When I went into the laundry room the washer was not running but the wash light was on so I opened the lid and felt the comforter and found it to be dry. I closed the lid and pushed the start button. After a few seconds the washer shifted to rinse without even washing the comforter. When the washer stopped running and the ready light came on I removed the comforter, unplugged the machine, shut off the water, disconnected the water hoses, placed the machine on a dolly and took it to my scrap pile. I could not find any Whirlpool washers with any good reviews so I purchased a Speed Queen with a 5 year parts and labor warranty.

I purchased a Whirlpool (Cabrio) Washer on March 1 2018. I previously had a Roper top loader with an agitator that was 22 years old. I used that washer for that many years and washed clothes 6 out of the 7 days of the week. Probably at least 20 loads a week. I never had a problem with it getting my clothes wet & clean. It never left them dirtier after washing them than they were before washing them. I am so disappointed in this washer!!! I can see it will not do any good to complain to Whirlpool because apparently they dont care about their customers. They think theyre products are perfect when they are far from it. I plainly told the associate I wash clothes every day. Really dirt clothes. (My son is a mechanic). I need a good washer. I can wash them by hand better than this washer does. I am very thankful I have not paid the full price for this washer yet. I will be calling them to come pick it up when my next payment is due. I will be going to one of the local consignment or thrift stores and purchasing myself an old timey top loader washer with an agitator for $100 or less. Whirlpool I had high hopes with this product and would have been buying a dryer to match soon but I believe I will stick to my Roper products or anything other than Whirlpool.

Just wondered if anyone else has had a problem with the paint bubbling up and peeling off their washer and/or dryer. My washer and dryer are in my laundry room off the kitchen with a heat and air vent in the room and I dont understand why my paint is doing this. They are about 5 years old and have always been in this room, never in a garage or basement. My dryer was rusting on the outside about 3 years ago and even though I bought the extended warranty, Whirlpool said it was only cosmetic and they wouldnt do anything about it. I bought them at Lowes and they were good enough to give me a new one to replace it. Both of the machines now have the paint bubbling up and peeling off and there is nothing that can be done. Anybody else have this problem and if so what can be done to repair the paint? This is my 3rd set of Whirlpool washer and dryers over the past 44 years and I will purchase another brand next time.

My washing machine ruined clothes with tiny rips. Small rubber pieces appeared in clothes. This happened during warranty but Whirlpool would do nothing. Finally, the bellow completely broke apart after 13 months. Repairman could not determine problem until this time. Whirlpool would do nothing.

On October 25, 2014, I lost my home, all of my belongings, and nearly lost my wife when my Whirlpool range model xfe371lvbo shorted out and caught fire. After spending thousands of dollars for an independent investigation to be conducted on the stove, it was determined that the control panel on the console shorted out, causing the fire. Since then, I havent had any response back from Whirlpool. I am in the process of meeting the required criteria for filing a claim, but have some questions, and everyone seems to be ignoring me. Please help.

We own this range and in 6 years its 4 main boards and 3 touch pads were replaced. The electronics suck big time. We have nothing but trouble with this range from day one and out-of-pocket cost for service calls that were recommended by whirlpool. They were absolutely no help. Expensive piece of crap! I will recommend NOT TO BUY ANY WHIRLPOOL PRODUCTS. The electronics suck big time! I kicked the Jenn Air out the door and to the land fill. I bought a new range, but not whirlpool product, with dials only, no electronics!

We bought a Cabrio washer four years ago for over 1,000 dollars. It lasted two years. The cost to repair was too high. We bought a low-end simple machine two years ago from Whirlpool. Now we are told it needs a new control panel, which again is going to make it not worth fixing. Two machines in four years. I called their customer service and there was nothing they could for me. The person they recommended to fix it told me it wasnt worth fixing and didnt even come out. I am done with Whirlpool.

The agitator is higher than any I have seen and when we washed aprons that have plastic buckles on them, they get stuck under the agitator. When complained their solution was to use laundry bags to wash 15 aprons in, they are long aprons. Paying a lot of money for the machine and it being commercial I didnt think we would not be able to use it. The whole machine shut down when three of the buckles got stuck. The washer is model # CAE2793BQ and I would suggest that no one purchase one of these machines.

The stove started having problems about 5 months after I bought it new, it had a 1 year warranty on it so the first repair was covered but it begun to have the same problem a few months after the repair. By the time I contacted the company they told me the warranty was expired and ask if I wanted to buy another year of coverage for $300, of course I said no. I repaired it myself and once again it worked for a few months and now the problem came back. Will not heat up so dont waste your money.

In May 2010, I purchased a Whirlpool WFW9750WW front load washing machine. In October 2010, the machine started making a strange noise and by December 2010, the machine sounded like a jet airplane. I called Whirlpool warranty and they sent out the appliance doctor. They looked at it and said that the bearings were shot and needed an inner basket, outer basket and one other item. They would order it and come back in a week or so. We were told not to use our machine. Ten days later, I called to check repair status and they said that the items were on back order until late January. I called Whirlpool and after several conversations and going to the second level of supervisor over a week time frame, they finally located the part and shipped it. However, it was not until the end of January 2011 (seven weeks after my call for service) that the part arrived and was installed. The sound was never right after the repair. The appliance doctor came out and told me that all washers are loud. In December 2011, the jet airplane sound returned. I called Whirlpool but I was now out of warranty. Luckily, I bought the extended warranty through Lowes. They sent out Night Owl on February 9th 2012. They diagnosed the same problem with the bearings and said they would order the parts. I called Night Owl on February 17th to check on status and they said that the parts were ordered. I called to check status again today and now the parts are on back order (same as last time) until sometime in March. Night Owl turned claim over to check on getting the machine replaced rather than repaired. I was told that this would be another five days. Its amazing how there are no parts available. I was told the repair cost for this item is over $450 as it takes two repairmen about two to three hours to complete. Issue is still not resolved. I highly recommend not buying a similar washing machine. Whirlpools product, warranty and customer service suck.

So I bought this $700.00 dishwasher. It has been several years since my dishwasher wasnt fixed, even though I called Whirlpool customer service several times.AGAIN, WHIRLPOOL HAS VERY POOR CUSTOMER SERVICE, INCLUDING DISRESPECTFUL, ARROGANT EMPLOYEES. The service was really slow. What, the materials took 4 months to get delivered? So today they leave a voicemail and they said that technicians were at my house at 12 noon WITHOUT even notifying me when they will get to my house. They basically just came to my house without asking me an question about the schedule and appointment. This wasnt first time. So I called, and the person was like Um, the technicians were at your house. Excuse me? She sighed and said tsk, tsk, tsk. This woman was SO DISRESPECTFUL. She tried to end up conversation by saying, ugh, the technicians will call you tomorrow morning and they will let you know okay?? Bye. and hung up the phone. I didnt have any chance to say something. Again, this is my bad experience. Never going to buy products in this company. Extremely poor customer service, with disrespectful employees. If you dont want to get bad experience, dont buy any products in this company.

Four year old Whirlpool Refrigerator/Freezer Model W10771736A. Ice maker broke right after the warranty ended. No refrigerator or certified whirlpool repairman was able to fix the problem. Our microwave is cracked on the side, and it is only four years old.

My Whirlpool stove works really well, and it is self cleaning. I have had my present oven/stove combo now for 5 years and had not had one single mishap at all. I am so confident that you will like it I am personally recommending it. It bakes beautifully and if there is a spill or overflow in the oven I just press a button & it cleans itself!

Bought a Whirlpool Gas Range model WFG530S0ES0 in Nov 2015. Eleven months into owning it the oven wouldnt heat up. Turns out the motherboard and wiring harness needed replaced. Since it was within a year of purchase, parts and labor were covered. Dec 2018 the same darn thing happened. I called Whirlpool and they basically said, Tough luck, lady. Was I surprised, not in the least. I talked to a supervisor who said that they dont have a single complaint on their Gas Ranges. Did I believe that, not in the least. Whirlpool finally agreed to pay for the parts but not the labor. Whirlpool supervisor said that equipment failure occurs. I said theres a difference between reasonable equipment failure and unreasonable equipment failure. For a 3 year old Whirlpool gas range to failure twice, with the same problem, is unreasonable failure. The supervisor said in such a pleasant voice, Basically too bad for you. Oh and have a Merry Christmas.

This is one of the best washers I have had 4 years now. The spin cycle is great. Feel almost dry when done. My daughter was going to order this set but cant get them anymore. I guess it is because it is too good of a washer.

We bought our new Cabrio (washer and dryer) in the fall. Within 2 weeks, I realized what a piece of crap these machines are. They simply do not clean the clothes. I have complained to the store where we purchased them, and I was told there is nothing they could do as the machines are performing as designed? Im waiting for a class action suit to join to get rid of this junk. Curt

I hate hate hate this Whirlpool Washer WTW5000DW1! To put it nicely. This is my first washer without traditional agitator and the sensing feature. I will never again buy a High Efficiency Washer with these features. It constantly gets stuck on sensing! We rearrange the load over and over and it still does not want to work. I have researched the online videos and this is a common problem. I wish I had researched prior to buying this type of machine.

I have a Whirlpool Gas Water Heater, product #0733136, that was installed in 2010. The pilot has repeatedly gone out and had to be re-lit. After reading some of the comments, I am amazed that other people were told to verify gas supply with the gas company (done) and clean the air intake (done) and then to call customer service and be told to do the intake cleaning again (done professionally six days ago). I will never buy another Whirlpool appliance, and fortunately, I am in property management and can advise others to avoid this company as well. I am extremely disappointed in Lowes for not doing a better job of providing reliable choices for their customers especially after these many complaints over the years. I have decided to replace the water heater with another brand immediately.

We purchased a brand new stainless steel refrigerator in 2013. Our 2 year refrigerator stopped producing ice and the freezer stopped working as well. We called Whirlpool customer service and they said they could not help due to 1 year manufacturer warranty only. We called another company (SoBellas) that charged us $85 to tell us that it is the seal system which should be covered up to 5 years by Whirlpool. The man showed me the Whirlpool refrigerator warranty on Google which states the sealed refrigeration parts are covered up to 5 years. There was no specific model numbers listed which gave me the impression this was a standard warranty for all Whirlpool refrigerators. I explained the situation to Whirlpool customer service including the 5 year warranty that is found on Google for everyone to see. I was told that our refrigerator model number did not qualify for that specific warranty. We ended up having to buy extended warranty for $350 on top of the $85 we already spent. This started July 24, we had to wait until August 10 for Whirlpools warranty company to see us. They checked it and said they had to order parts but he supposedly tweaked it to make our fridge run better.... It made it worse and it ended up completely breaking down. We had to buy ice chest and waited until Thursday August 27th for them to finally come back with parts and fix the refrigerator. I took time off from work once again due to our time slot being between 3 and 5 but the guy didnt even show up until 7:30. I could have worked my normal hours instead of taking more time off! The guy never once called to inform us that he was running late. We kept calling the company to make sure we werent forgotten. The guy told us that everything should be working within 20 hours or so, by Friday our freezer was still not working and no ice either, back to square one! I called Whirlpool customer service once again to explain the situation, nothing could be done. The next available time for them to come back out is September 17 for them to come look at our refrigerator. We have been stuck without ice and a freezer, buying food every other day waiting for our brand new, horrible Whirlpool refrigerator to be fixed. Will never ever buy Whirlpool brand again! Actually, we purchased all brand new Whirlpool appliances... Good luck to us!!!!!

My husband and I purchased our Whirlpool Gold French Door Fridge-Freezer on bottom in January 2012. Water collects in the bottom of the freezer and creates thick sheets of ice. When the bottom of the freezer is a full sheet of ice, the water just drips onto the floor. I come home from work to a river of water that stretches across the kitchen--and now my linoleum floor is warping from the water. This started only 6 months after we bought the refrigerator. Im sure the warranty is out--what can I do?

I bought a commercial coin operator washer (Whirlpool washer model CAE2743BQ) for $800 and after using it for 4 months the washer stop working. The main board panel lights turned all and the washer did not start. Called Whirlpool several times and nobody could help me and told me to look online for a distribution center to get parts. The customer service only knew about regular washers not coin operator. The washer had only 3 months warranty from Home Depot and I was supposed to pay for all the repairs and Whirlpool would pay for parts. So far I spend $400 in repairs and the certified technicians could not repair the washer. They replaced the actuator shift, the main board etc, etc and nothing. The technicians reset the washer at least 10 times, calling Whirlpool tech support and the washer worked for one load and the main board lights stayed on all over again, the start button did not work. I sent a letter to the warranty department that I got online and they told me to call the same 1800 that I had called at least 50 times in the past year. Now it has been more than one year and the machine is defective. Technician said could be the soap that my tenants are using, or overloading the washer or an electric problem that they cannot identify. I gave up... I will not buy a coin operator heavy duty washer from them again. I requested a return authorization for a defective product and I did not get anywhere. Thanks.

I spent the extra money and bought a very nice looking Whirlpool range and oven. Within months, it started rusting. I keep a meticulously clean kitchen and Ive never had this problem with any other appliance. I sent letters to no avail. They said that their warranty on rust was 30 days! They refused to do anything about it and told me to go ahead and sue them. Terrible product. Defective from the factory. Do not ever buy a Whirlpool product as they do not stand behind it.

I bought all my kitchen appliances in Home Depot 4 months ago (April 2014). The wall oven, Whirlpool, never worked. Flamingo Appliances is the name of the company that does services for Whirlpool in my city. They keep changing parts and today is the 3rd visit that the technician will be in my house trying to solve the problem. Customer service in Michigan is DISGUSTING! I probably have to buy another oven because they say they wont replace it if they think its fixable. 3 MONTHS! I will never buy Whirlpool again. I hate them.

I have tried to contact Whirlpool, email and telephone call. Finally someone called me but Customer Service was poor. I asked her to have a Manager call me, but she never did. They also never responded to my email. We Purchased our new Refrigerator 21 c.f. side by side 2 months ago. The ice maker is driving us crazy. It is very loud. There are white plugs on the 2 bottom corners that make the appliance look extremely cheap. I am not happy with this Refrigerator!

Design is made so you will need a repair man to clean filter. The machine has to be taken apart to get to filter. About one hour of your time. If youre not handy its a paid repair About $250 to $300. Also the valves that control the water into the washer failed after about 5 years. An easy fix part costs about $60. All appliances are designed to fail after the purchased extended warranty expires. More features more repairs. So if you arent going to use a feature get a simpler machine. More money does not mean better machine. Or that it will last longer. The days of an appliance lasting 10 to 20 years are over.

I purchased my refrigerator (Whirlpool side by side refrigerator model ED5FVGXW507) in January 2013. We travel more than 6 months out of the year, so we have not had excess usage from the refrigerator. After only a few months, the plastic drawers started to crack. Now, after less than a year and a half, all my drawers are cracked, as well as all my door bins. I will be married 50 years in December, have owned refrigerators for all those years, and this is the first time that I have ever had a drawer crack, let alone all of them, as well as the door bins.

My house was built 20 years ago, with all Whirlpool appliances; built-in microwave over the electric oven, gas cooktop, and under counter dishwasher. The oven just gave out. Everything else works fine! Let me repeat that. I have a 20 yr old Whirlpool microwave that works just fine! Well, since the oven broke, we thought, maybe its time to update all the appliances. We went to the large appliance store from which our original ones came, and were told that all microwaves are now made in China by Sharp, and are crap!! Wed be lucky to get 3 years out of one. My jaw hit the ground. I couldnt believe the appliance salesman was telling us this! In fact, the appliance repairman that diagnosed my oven to be unrepairable ($100 trip charge, thank you very much) didnt have much good to say about the newer refrigerators... They contain much less Freon and dont seem to hold up as well... So, I guess Ill just keep my old appliances going as long as possible! How can appliance manufacturers stay in business!

Six months after purchasing my Whirlpool Washer model number WTW5000DW0 I would hear what sounded like rocks in the bottom of spin drum during spin cycles. Then noticed it was taking longer for clothes to wash and sometimes the water did not completely drain. Called for Service under LOWES warranty (the worst people to deal with). Tech comes removes a penny and dime and tells me that is the problem. Leaves. 45 minutes after he leaves there is the noise again. Call and set up for this Service Company to come back. Even though they went out of business prior to the appointment Lowes Service would not listen to me and insisted I stay home ALL DAY for someone who did not show up. Repeated calls to the Service Company resulted in nothing - phone disconnected.So finally after much frustration I am given new appointment with new Service Company - PARRISH. Tech comes in here five minutes and wants to know the sound, I explain. He checks out the unit and tells me it is a major problem and the part and labor will be costly. Best if they just replace the machine. His added comment - I see a lot of this. So if this machine is such a problem why was it not recalled? I am getting a replacement as I have warranty and machine was not a year old when problem started. Lowes Service Contract is another problem but I will deal with that later.

Our Cabrio washer often ties clothes into (unwashed/still dirty) knots. They are so bad that it takes several minutes to untangle and then the load has to be rewashed. It also has to be set for hot water when you want cold, and vice-versa. I am unable to do that for the rinse cycle, so all our clothes are rinsed in hot water. It doesnt even get the clothes clean, when it doesnt tie them up. Ive gotten used to it sounding like the space shuttle taking off and managed to shut off most of the annoying beeps. The dryer is almost as bad, it seems to take a long time to dry clothes, and they come out very wrinkled, even on the wrinkle guard. The finish isnt even good on either one. It scratches very easily, and scratches start to rust almost immediately. This is quite possibly the worst piece of junk my family has ever owned, except maybe for an unfortunate experience with a 77 Dodge Aspen. We bought this set thinking we were paying enough that we were getting the best. Never again!

I dont like the sensing feature that takes away my choice of water level control. I dont like the locking lid. It doesnt clean the heavily soiled clothes and I have to wash them twice because of the low water level. When the water is running in during the spin cycle, after the rinse cycle it washes away all the fabric softener. It takes longer from start to finish, so I dont see how it could be energy efficient. I dont like anything about the so-called energy efficient models. My opinion is they should not have changed from the old model. If it is not broken, dont try to fix it! I will never buy another Whirlpool product unless I see some significant improvements.

It took several delivery attempts to get a refrigerator without cosmetic flaw and it only lasted four years before Freon leak in evaporative system occurred. It would have cost more to repair than replace. Needless to say, I replaced it with another brand.

I purchased a gas hot water heater from Whirlpool. I have had problems with it since it was new. Whirlpool kept sending repair parts, which I installed, until the warranty expired. Now they say “Sorry Charlie, the warranty has expired.” The water heater has never been fixed. They just dragged it along until the warranty expired. Whirlpool has no complaint department or the repair place will not give it to you. They told me there would be no use for a complaint department. They would just tell the same thing the repair was telling me.

Purchased on 9/12 at Home Depot. Ice maker paid for as stated in ad for home depot, did not come with fridge. Tech needed for warm food, had to repair gasket. Tech needed for cracked handle. 6 calls for freezing food in fridge compartment. No resolve. Whirlpool wanted a 2nd opinion and another tech came deeming the fridge unrepairable. Not good enough for Whirlpool. After speaking to several customer service agents, they said they do not refund or replace, only repair. I have lost hundreds of dollars of food from freezing. My fridge is reading at 31 deg. This is way below what it is supposed to read at. No call from Whirlpool since last tech came. Their customer service is terrible and cold. Whirlpool Corp. was not any help either. You can see the problem with this model if you look up Whirlpool fridge freezing food in Florida, as a woman there called ABC news and they reported it. I will also do the same.

New water making loud pinging noises when burner shut off. Whirlpool referred plumber. Plumber stated this is normal. After few months heater would make loud humming noise when burner turned on. Called Whirlpool again. Said I had to pay for plumber to troubleshoot and if part needed I had to pay labor to replace part. Would never recommend this product to anybody.

I am somewhat satisfied with my induction range. We ordered it just before Thanksgiving from Lowe’s a year and a half ago. We were told that we would have it before Christmas, which was fine with me. I don’t cook for Thanksgiving. Just a lot of Christmas baking. It turned out that Whirlpool had not started making our range until January and it wasn’t delivered until mid-January. It had been really good until about a month ago, when it blew the circuit breaker. My husband was cooking dinner while I was at work and it just blew the circuit breaker. No power surge in the rest of the house. No other circuit breakers affected. When the power was turned back on, two burners were out. As it turns out, the main circuit board is dead. So now the one large burner, a small burner and the ovens don’t work. There are two circuit boards for each oven. When it is working, it is a great stove. However when it doesn’t work, it is costly and takes a while to get repaired.

Sounding like a broken record, this washer is such a disappointment! I had high hopes for this top loader and thought I did enough research. Bought a Cabrio in Oct 2016 and have never liked it. They will have you believe it’s your fault... the wrinkly clothes, the clothes not clean enough, the white marks over all your clothes... you can’t change your detergent or softener enough and change the amount enough... it will still be there. So disappointed??? Want my front loader back!

Its supposed to be energy efficient yet it takes AT LEAST two times as long to get one load done, regardless of size or cycle preference! Now laundry takes all day! Literally! And why is there a lid lockout? Did someone accidentally fall in? If I drop something after Ive pushed start, I have to wait until the machine unlocks the lid. Why? This seems counterproductive. Its a top loader!

Will never buy another Whirlpool/GE product again. Nothing but problems. Paid $1700 for a Whirlpool/goldstar refrigerator 2 years ago. Problems from the start with slide-out shelf cracking, evaporator fan burnt out within 2 years, digital display cannot read anymore. Now have another problem again - not cooling. Going to the trash. No wonder your stock price have dropped. I would sell off to. Whirlpool/GE have been going down hill for the last 5 years. Maybe more. Cheap products, do reflect, it just a matter of time, I would think you would address these issues in your product line, but it shows your company is all about profits instead of quality of products. Keep going like you are, and you will be bankrupt. Cheap overpriced and nothing but junk in any products you manufacture.

Problem resolved - This is an update to my previous complaint... The repair man arrived this morning and after resetting the thermostat, the water heater started up again. He explained to me that these new water heaters are super sensitive because of the new designs and systems that are required by the State of California. He said that all brands have to have the same system. He said that the new water heaters dont breathe as well as the old ones. In our case, he suspected that after being installed, there were probably some air bubbles in the pipes which tricked the computer into telling it that there was not enough ventilation, when in fact our ventilation was fine, but that triggered a total shut down! In my previous written complaint, I was really upset because I have not had a shower in 3 days and thought this problem water heater would not be fixed until next week. I was furious! My understanding is that basically the way the new water heaters are designed is not very well and there is nothing we can do because about it they are all the same, unless we want to go to a tankless water heater system which plumbing included would cost $4000.00... so we are stuck and hope this will not happen again!

Water saver does not provide enough water to wet the clothes. Even deep wash cycle does not provide enough water. This is right from the start. We should have returned it the next day rather than trying to learn how to use it wasting time so it could never be returned. I rated them as 1 star because there was nothing less I could have given them. DO NOT BUY ANY WHIRLPOOL PRODUCTS.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

Purchased model # WRX7355D8MOO through Lowes summer of 2013. By summer of 2014 ice started building up under freeze drawer. Little did I realize the compressor was failing, air flow was stopped up. Ice maker failed. In 2016 water dispenser calibration off, freezer failed. Called in certified Whirlpool repair. They spent three days troubleshooting problems. Repairmen told me, not to spend any more money to repair this fridge, buy a new fridge. I spent $2300 on this fridge. Its only 2 1/2 years old. Whirlpool better get their quality control issues resolved or shut down the plant. I know many part are made in Mexico, poor quality. Why pay for an expensive appliance that only last two years.

Whirlpool Cabrio Model WTW6500WW1 - Have had good luck with previous Whirlpool Washers so thought I would purchase this one 2 years ago from Menards. Paid more than I normally would and thought it would be worth the extra money. Not so.......As many others, it has a foul odor that will not go away and now sounds like a freight train in the house. Called Whirlpool about this issue and parts are not covered. Total cost of parts including the tool that is needed for this repair is $187.00 not including shipping. Whirlpool has lost my business moving forward as like many others, Im sure. Very disappointed!

After 12 months (warranty) the bearings had to be replaced, $300. 12 months later bearings needed replaced again for another $300... was told by the repairman not to waste my money. This would happen again in another 12 months. This is a issue with these washers. Opted to get something else. Very unhappy to only get a couple of years out of this machine. I have also had to wash some loads twice to get clean... unacceptable performance!!! Contacted Lowes & Whirlpool to no avail of course. Never again!!

I had a Whirlpool dishwasher for year and it worked great, but the baskets were rusting. I decided Feb 2014 to purchase another Whirlpool dishwasher. It did not clear as well as my old dishwasher. The seller of the dishwasher stated it was our water or detergent. The water and detergent were the same. The only difference was the dishwasher. Day prior to changing the dishwasher, the dishes were clear and the day I changed the dishwasher, the dishes were not clean. November 2016, the main board has gone out. The part costs $148, plus the service call. I called Whirlpool. They stated they would sell me the part or would discount a new dishwasher. I think they should discount the part!!! Whirlpool makes most brands of dishwashers, so you cant change companies. Their quality is all you can get.

I purchased a Whirlpool induction cooktop Aqualift self cleaning oven Nov.1/12. The oven has never been easy to clean you always have to scrub it, now I boiled some pies over in Oct/13, the syrup burned into the bottom of the oven before the pies were finished baking. My oven is now pitted, warped, and bakes very unevenly, have contacted the merchant, Saskatoon Appliance, Whirlpool, and Excelsior Insurance (extra warranty) Insurance guarantees 24-48 hr service but to no avail. We still have no service 1 month later.

Whirlpool Duet 3.9 cu ft High-Efficiency WFW9451XW00 - Hear my first experience with Whirlpool. I purchased a washer machine 30 April 2014. Guess what - machine stop working suddenly on July 30th, just about three months later. I had a lot of guest from overseas. While they visit me, I did not have my washer machine. How embarrassing. It was big mistake to buy Whirlpool. It is all made plastic inside and they uses cheap Chinese material. Anyway, technician came house to check what the problem was... all control system was burned. He ordered almost 10 parts from Whirlpool on 04 August. Whirlpool scheduled delivery for 20 of August. I called them for them to send the parts faster so my guests could wash their clothes. They send them little faster for August 16. After a day, technician was in the house again. I waited about 3 hours for him to fix my machine. He was really nice guy. He put install all new parts. Just in front of me, new parts broke after 5 minute. Whirlpool still did not contact me about their decision. Today is August 26th... I called them 5 time already - Nobody give me useful info. NO Whirlpool, guys - bad service.

I purchased the Cabrio washer during the black Friday sale. The washer was a pretty slate gray. I loved the color and the fact it was a Whirlpool, which I thought meant quality. It was expensive but we were updating our appliances as our 10 year plus washer needed replacing. Big mistake. This washer is terrible. It keeps me stressed. There is not enough water to clean the clothes, my husbands white underwear is always dingy and dirty looking. The sheets are dirty and smells. I try putting bleach on whites before washing and the whites still come out with underarm stains. I tried all the recommendations to no avail. This machine is awful. This was a big financial mistake. As soon as I am able this machine is gone. Will go back to the agitator in the middle, and NOT a Whirlpool. I DO NOT recommend this machine unless you want something pretty because this is NOT a washing machine.

In March of 2013, I purchased a Whirlpool refrigerator; model number WRF990SLAM00 from Lowes. About two weeks after my manufacturers warranty expired, I called Whirlpool because the refrigerator wasnt working anymore. It took several weeks and the need to call four different repair companies before we finally had one that was willing and able to come attempt to repair the refrigerator. They came out, changed a few parts and left. Several weeks later, the refrigerator quit again. This time, when I called whirlpool (about June 2014), I was able to convince them to give me an extended warranty. They told me that the warranty would expire in December, and that all the work and service would be covered up to that date. This was fortunate because that repair, parts alone, was near a thousand dollars. Of course, the repair company couldnt make these repairs in my kitchen, so they had to remove the refrigerator and take it to their shop for several days. By this point, we had lost two refrigerators full of food. In mid-November 2014, the refrigerator quit again. We lost another refrigerator full of food. We called Whirlpool and the repair company again, and the repair was scheduled. I have six children and we spent Thanksgiving without a refrigerator in our home. The repair shop kept the refrigerator for several days after they fixed it to make sure it wouldnt leak coolant, because by this time, they had figured out that there were several pin hole sized leaks in the coolant line. It didnt leak. They had it for about four weeks total before they brought it back to us. By the next morning after having the refrigerator plugged in for several hours in our kitchen, the temp was at 65 degrees in the refrigerator and 60 in the freezer. I called the repair company again and whirlpool. The repair company has come to the conclusion that there must be a leak in the coolant line in the walls of the refrigerator and it is deemed unrepairable. They called the whirlpool tech line and the tech people told them to come back to our house and read the pressures the next day. They came out, read the pressures, determined that coolant had leaked out and told the tech department it was not repairable. The tech department told them to go through the entire cooling system again. This is something they have done several times. Today, they brought the refrigerator back after going through the entire cooling system, yet again. Its still not working. As I type this, my refrigerator is at a balmy 55 degrees. The repair company and I have both, on numerous occasions requested a replacement refrigerator. This was a very high end purchase for us. The original cost of the refrigerator was around $3,000. I have lost around $1500 worth of food, which Ive also requested on numerous occasions for Whirlpool to reimburse and they refuse. Whirlpool refuses to replace the refrigerator. Today, I found out that, by mistake, they gave me a one year extended warranty instead of six months. They said that it does not expire until June 19, 2015. Even with this information, they told me that the best offer that they will give me is IF I am willing to EXCHANGE my lemon that is in my kitchen right now, they will SELL me a replacement refrigerator at a discount. They say that the terms of the extended warranty are different than terms of a manufacturers warranty.This is unacceptable. I am currently out several thousand dollars for an over sized filtered water dispenser in my kitchen. Throughout 2014, we spent somewhere between three and four months without a working refrigerator in our home. As of right now, I havent had a working refrigerator for about six weeks and through Thanksgiving, Christmas, and New Years. I bought the refrigerator because I thought it would act like a refrigerator and not a paper weight. An Implied Warranty of Merchantability has no expiration date. It requires that the goods be fit for the ordinary purposes for which they are to be used. This refrigerator is not fit to be used.Id also like to mention that during the times that Ive spoken with Whirlpool on the phone, they have told me that they would replace the refrigerator if the repair company deemed it unrepairable. Typically when I call whirlpool, I am on hold for fifteen to thirty minutes before I get to a representative. Today, I was on hold for forty minutes before my call was disconnected. This has happened numerous times. Ive also had representatives disconnect the call several times when they were transferring me to another department, or putting me on hold. I estimate that I have spent at least forty hours on the phone with the customer service department for whirlpool in the last several months. And even, with all that, I have not had a dependable refrigerator for eight months. I need this resolved and I dont feel that it is fair for me to be financially punished because of the lemon that Ive already purchased from Whirlpool.

Its awful! We paid over $600 for our Whirlpool Gold Series convection/microwave clean release oven (model GMH 6185XVQ1). It worked fine for 12.5 months at which time it started clicking and, after a final zapping sound, would not heat anything at all. I called Customer Service, Oh, so sorry, its past its one year warranty. I was finally transferred to Escalations then to the supervisor of the Escalation specialist. Finally, we negotiated that I would pay for the service call ($129) and they would pay for parts (which were around $300 for a fried magnetron, diode, and something else). That repair was 6 months ago. Today while heating a glass of water in our microwave, I heard the familiar zap and no matter what, the microwave will not heat anything. I called Customer Service again, figuring the newer parts were still under warranty. Wrong. The newer parts were only covered for 90 days. This time, they tried to sell me a service plus package. For only $289, they will re-warranty my microwave for 1 year after they come out and fix it again (cost on me). My other option is to pay $129 again for another service call plus any parts (which Im sure will be about the same as last time. I will never buy Whirlpool again! Buyer beware!

Bought a whirlpool refrigerator in 2015, have had both handles replaced 3 times, the bottom pieces of the handles are made of plastic and they crack. We had to take them to a metal fabricator and have them replaced with metal to keep them from breaking. Lowes and whirlpool know of this problem and they do nothing about it. Will not buy another whirlpool product. Very dissatisfied.

We got our Whirlpool french door refrigerator with freezer on the bottom (Model: GX5FHDXVY04) in June 2010. In the past six months, the refrigerator portion loses cooling and temperatures go to the 60s or 70s. We found out that by turning the unit off until it defrosts, it will work again for awhile. Weve had water overflow on our wood floor. When this happened the third time, I called Whirlpool to send a repair person.The person I talked to said it could be over $400 to repair and that it would be more economical to get an extended warranty for about $314, which I did. I did not receive the contract via email (it may have gotten lost in spam). The repair man came and said yes, this was a common problem due to a design flaw and that it needed a $6 part to make the water drain smaller - so that too much air didnt get in.It was May 1st before the repair could return to install it. This was done and we thought - expensive but its taken care of. Today, May 5th, the same problem happened and I have to throw away food again. Its the weekend and there is not a repair person available for two weeks - I got an order number and may request that the repair come sooner. To add insult to injury, I found out that the extended warranty is good only up to $450 and not good for any repair that might be needed in a year. Most of the repair goes to travel to get to Fairfield and labor and we have used most of the warranty already.

Whirlpool gas range Model WFG5245LAB2 has serious flaws that are a danger. I noticed the handles to turn on the burners seem sloppy. So sloppy in fact that just brushing up against the knobs will turn the gas on. This happened when I had someone visiting and we returned you could smell gas in the house. We were none the worse since we were out however my 3 cats were in the house the entire time. Tonight I removed the large grates that go over the burners to clean the porcelain. Once again I brushed up against the handle and the back burner ignited causing me to burn my hand. This stove is a danger to all.

The washing machine started leaking and making a noise like a freight train 6 months after purchasing it. We complained in February 2011, but the parts were not available until March 31, 2011. The same problem occurred in September 2011, and we are still waiting for the parts until October 18, 2011. In the mean time, I have been spending hundreds of dollars doing wash at the laundromat.

Our new Maytag (i.e. owned by Whirlpool) oven/range is a stainless steel pile of junk. It takes FOREVER to pre-heat. The range elements take FOREVER to heat up. And like others on here, the Aqua Lift cleaning simply does not work. We put the oven through 3 back-to-back cycles and only the bottom gets a little clean. What a scam.

I purchased Whirlpool only front load compact washer in June 2015 and lasted only a year before the door lock broke and getting F6 error that means mother board to be replaced. Whirlpool warranty department (AIG) did not bother to do a complete repair and offer buy out at a 75% of my purchase price. My five year warranty premium cost was not refunded. I do not recommend this model be purchased by anyone. Whirlpool washes its hands on the quality and reliability of its product in US and that is a shame! A service life the unit should be at least 9 years with affordable maintenance cost.

My new Tridel Condo came with a brand new Whirlpool washer and dryer and the washer has not been working well since the beginning. After several service calls the repairman finally gave up and now were getting a new replacement. However its been a nightmare working with them trying to get this washer replaced. The Whirlpool delivery team and the service team cant seem to coordinate a time together for the replacement. We had to make a first appointment for the service guy to uninstall the old unit, the second appt for the delivery guy to drop off the new unit and pick up the old and a 3rd appt to install the new unit. Each appt has a 4 hour wait window. This is their standard procedure, which is totally inconvenient to customers. To make matter worse, the delivery guy came too early for a condo delivery (before 9 AM) and told us he will be back the next day. And he didnt show up. It looks like now we actually have to have 5 appts (including the 2 missed appts by their delivery guy) to have the washer replaced. All the time I wasted waiting for this delivery is worth more than the washer itself. What would be 4 hours X 5 appts = 20 hours. This is the worst customer experience ever. After 3 months of constantly calling Whirlpool and still no washer. Whirlpool needs to hire some competent people who actually care about servicing their customers.

I have not had any issues with my washing machine yet as I have only had it for two and a half years. The features the machine offers are good and there are many options. So far the washing machine has worked as advertised / expected.

I am a retiree after 35 years and 5 months, the last 20 plus years on salary. I purchased a new Whirlpool washer on April 18, 2012 at Lowes in Tiffin, Ohio. The clerk said to take the receipt to Clyde to apply for my rebate. I was informed by a receptionist that we only get a rebate if our purchase is from Sears. I only went to Lowes because of the urgency and was not aware of this change in your policy. I consider this a real slap in the face after all the years of what I consider excellent service to Whirlpool Corporation.

When we bought our house the Matching set of Whirlpool Cabrio Platinums came with it as they were new. I decided to keep them and sell my LG Troms.Absolutely the worst mistake was keeping these Whirlpools. Who in their right mind would consider a washer with no agitator a washing machine? The clothes just sit and do nothing. They don’t get clean at all. Its a complete pile of useless junk and the person or persons who engineered it shouldn’t even be in charge of designing birdhouses.Whirlpool themselves should be ashamed to put out such a pile of garbage to the consumer. Our house came with all new Whirlpool appliances and we are going to replace them all and never give Whirlpool a look again. Whatever you do don’t fall for the shiny unit, slick salesmen. Because all youre going to get with Whirlpools washer is all talk and zero action. Thanks for the not so clean clothes Whirlpool. The local laundry mat thanks you when I need to actually clean my clothes.

We have the four-door model, french fridge part, drawer, and bottom freezer. Overall has been a good appliance. Icemaker burned out in third year. Icemaker replacement is very noisy, popping and groaning during drop-out and refill. Noise level otherwise is average.

I purchased a Whirlpool top load 8500 washing machine from LOWEs two years ago. I noticed that the clothes were not getting wet, clean, were coming out covered in lint, soap film and stained. It is misleading to call it a HE washer since I have to wash each load 3 - 4.5 hours. It is NOT energy efficient if you have to wash each load of clothes 3 times with a rinse. I have tried all of the tricks - changing soaps, labeling the wash as bulky, wetting the clothes to add weight... Washing clothes should not be this complicated. The clothes are sorted appropriately and washed in the right temperature. I do not understand what is staining the clothes. I put new white towels in and they come out stained (see photo)? Lowes sent out a repairman who said the machine would never clean the clothes since there was not enough water in the washing machine to wash the clothes. I tried to return the washer to Lowes but they said it was past the 30 days. Unfortunately, I purchased the appliances on a Lowes credit card so there was no recourse. I then contacted Whirlpool and was put on hold and transferred to various people before I gave up.

When washing towels or a blanket or quilt, anything substantial it wont spin the water out of the laundry. This washer is only 5 months old.

I purchased Whirlpool top loading washing machine model # WTW57ESVW less than 2 years ago. It stopped working yesterday. I had a trusted professional repairman evaluate it today. The motor needs to be replaced after less than 2 years?! The customer service reps basically said sorry. I should have purchased the extended warranty. Is it not reasonable to trust that a Whirlpool washing machine motor should last more than 2 years.I am very unhappy and very angry that Whirlpool will not stand behind their product. The last customer service rep I spoke to suggested she could send one of their repairmen and replace the motor at a cost to me of $299.00. So, after less than 2 years, I am offered an amount to pay of about half the cost I paid less than 2 years ago for the brand new washing machine. My home is full of Whirlpool appliances. I have been a good and loyal customer for over 30 years. I am very angry and upset with Whirlpool. Please explain to me why it is not reasonable for me to trust and believe that a Whirlpool top loading machine that is well cared for and not abused in any fashion should last longer than 2 years? Is this being a loyal Whirlpool customer gets you, I should have purchased the extended warranty”? We are talking about a motor here, not a fabric or bleach dispenser that breaks. Although, those parts should not break either, there is a big difference from something like that and a motor. Please contact me as soon as possible at either number listed above. Thank you.

Avoid Whirlpool at all cost. I have had the GSS series, which was horrible. It was declared unfixable by service after 2 weeks of ownership. It was replaced with a similar WP model WS series and was told it was basically identical to the GSS series except for some cosmetic differences (They do look identical and yes, it’s just as horrible as the GSS.). The first one was defective from day 1. It was replaced and assured the next one would be thoroughly checked out prior to delivery. Obviously, nobody did this (was still in box and never opened). The fridge arrived and had the same exact defects as the previous units. Service literally said these were junk and they had nothing but issues with them that they simply cannot fix, and issues Whirlpool is obviously aware of but will not admit to, nor back up their products. Service literally told me to avoid WP at all cost or I will have nothing but non-stop issues and non-stop service calls and the fridge will still not be fixed. I purchased the extended 5 year warranty that clearly states that the fridge will be fixed or replaced if deemed non-repairable. Mine was! Yet, neither Whirlpool nor the retailer will do anything. I was literally told Take it to the dump and go buy a new fridge by both Whirlpool and the retailer. My purchase was less than a year ago. The 3rd fridge has only been here 3 months. They took my $1,500. They took my money for the extended warranty. It has been declared non-repairable, yet Whirlpool’s and the retailer’s response is Too bad, we are keeping your money, not honoring the warranty. We don’t care if it’s non-repairable. Take it to the dump and buy a new one.This is new! The money it cost, the money for extended warranty, the money for lost food, the money for lost wages due to having to be here for repeated service calls, the huge amount of time spent using hair dryers and everything else under the sun (this fridge must be baby sat and monitored pretty much 24/7 due to more issues than I can list). The fact this fridge has taken over my life, with freezer and fridge unusable (totally unusable, it has taken over my life, but I still can’t use it and spend a fortune getting take-out food) is just shocking, but more shocking is the fact neither WP or the retailer (the blue one that starts with an L, ends with an S and competes with HD the orange store) will stand behind the product or the warranty and instead is telling me to flush multi thousands of dollars down the drain and take my new, with extended warranty, to the dump and buy a new one. Calls to both companies only led to more wasted time and frustration.I don’t even see how this can be legal. They happily took my money. They fully explained how I needed the extended warranty in case something like this happens and assured me the extended warranty would protect me in case something goes wrong for 5 full years. They will replace it with a new one if un-repairable. Yet in less than a year, Ive gotten 3 defective ones with the last one only 3 months old with the first service call made on the day after delivery, but I’m supposed to throw all this money down the drain, take my new fully warranted fridge to the dump and buy a new one?!Shocking and not something I can afford to do. If I could afford it, I would get this thing out of my house in a heartbeat and buy something else, but I’m not made of money so this is not an option. Not sure what I can do other than to warn others to avoid Whirlpool and avoid the retailer (L---s). I’m just in shock and to say I’m upset would not even come close to describing my utter disappointment and frustration with both companies and this whole ordeal (never ending nightmare is more appropriate).

I purchased a Whirlpool gas stove model #WFG540H0AH from Sears in March 2103. Since that time, the oven has repeatedly broken. After two major repairs, the repair company said the fas venue (?) suspect board was defective and needed to be replaced by the manufacturer. After 3 weeks of back and forth calls with Whirlpool customer service, the only solution they provided was for me to purchase a new stove at a discount with no compensation for installation, the gas connection kit, or haul-away of the old appliance. The original stove cost me $1100 including the installation, haul-away and taxes. The replacement option would have cost me $800 and still did not included haul-away, the gas installation kit, or taxes. Hardly an affordable solution. Whirlpool at no time addressed that a part on the stove was deemed defective.

I purchased a Whirlpool cabrio mod. wtw5840bwo washing machine in Oct. of 2014. As of June 2015 I am ready to kick it to the curb. The washer works to it design and hasnt broke down but it doesnt clean our clothes. We load the machine, add the right amount of clothes and recommended detergents and 1hr later after the wash cycle is completed, the clothes still stink with the smell of daily perspiration. I went back to using our old washer that has a worn out agitator. It does a better job.

I purchased a Whirlpool refrigerator, model # ED2FHAX005, serial #SW1126490, two years ago. I have nothing but trouble with the ice maker. It keeps jamming up with frozen cube. While under warranty, I had it fixed but since then, it has happened twice more. The repairman who fixed it said there was a part missing and a part of the unit was melted. Not only that, but the plastic is coming off on the handle. Nobody at Whirlpool will help me. Too bad, there is no warranty anymore. This refrigerator is a lemon. I am so sorry that I purchased it.

This washing machine has been the worst machine I have ever owned - I have called Paddys Market on several occasions to have a repairman come out and take a look at this machine, which they did - but the machine never got any better - it has never ever washed my clothes properly its a piece of garbage - clothes come out dirtier than when they went in and sometimes come out dry. Its so busy trying to save water - it doesnt use hardly any - and forget doing bigger loads - I WILL NEVER BUY ANOTHER WHIRLPOOL product again.

Six warranty visits and the fridge still doesnt work. Cools to around 44 degrees in the upper part and lower part barely freezes. We have gotten sick from food left in the fridge after two days from the grocery store. It is now approaching two months without the use of our new refrigerator. DO NOT buy a Whirlpool. Apparently there was a manufacturing defect. We are now learning that a $2,400 fridge doesnt seem to be able to be fixed by factory-trained specialists.

We purchased a Whirlpool dishwasher in August of 2014 (Model #WDT710PAYM6) and it broke for the first time in the summertime of 2015, so it was still under warranty. The manufacturer set us up with a local company to fix it. First of all, the guy comes out to look at it and has no parts with him whatsoever to fix it once he figures out the problem. So we ended up waiting for over a month before our dishwasher was fixed. That is a long time to have to hand wash dishes, especially with the amount that we go through each day. I know that ranting about having to hand wash dishes is such a first world problem thing to complain about, but my gosh...if I buy a brand new dishwasher for a good amount of money, I shouldnt have to hand wash my stupid dishes!!It has now broken AGAIN and it is no longer under warranty. We called Whirlpool to see what they could do because it should not be breaking this often. They told us we could either spend $250 for a years worth of maintenance on it, or just pay out of pocket. So you want me to pay $250 or more to fix a dishwasher that we spent over $400 on that has broken twice in a year??? Ive been looking on their website for this model to leave a review and cannot find it, so that leads me to believe that it is discontinued. So thank you, Whirlpool for the piece-of-crap dishwasher. I can see you really take care of your customers when they call about their concerns too. I will NEVER buy any Whirlpool appliance again, and I will be sure to let all of my friends know they shouldnt either. If I could rate this with negative stars I would. So now we have to go out and purchase another dishwasher. Thank God Cyber Monday is here. So I cannot say it enough, do not, do not, do not buy a Whirlpool. If you do, youll find its actually a Whirl-poo, because its a POS.

We been having the same issues as all of the people that have consumed the water heater. We have replaced the pilot more than 3 times and other parts of this water heater! Well, we are a family of 9 and the only way we can shower is by heating up water like everyone that has the same issue.So I would never recommend this (Whirlpool) water heater to anyone!

I purchased a new Whirlpool Cabrio set, in 2009. I bought the top loading washer, and matching dryer. Since 2009, I have had the washer serviced FIVE times. Bearings, water pump, F1, F2, ul codes, and a few other things, I honestly cant remember. I love this capacity. But that is all I love about this machine. Today, the water pump went out again. I have been reading online regarding loose coins making their way into the drain pump, the hose, and other parts of the washer. I am diligent about emptying my pockets, but, obviously, someone in the house is not. There should be a trap for the coins, buttons, and any other debris that passes through, but, clearly there is not, and it appears I am not the only one with this problem. I am so frustrated. I paid almost $3,000.00 for this set. It was my very first brand new set and I have had so many problems with this. With all of the problems and all of the complaints, and so many similar complaints, why is Whirlpool not acknowledging them? Why are they not doing anything about it? Side note, my dryer works fine.

I bought a Whirlpool French door, freezer drawer on bottom at Lowes 2 years ago for $2,600. The refrigerator needed a new motherboard within the first year and now that it is in the 2nd year, service is required again. The repairman ordered the part and came the 2nd time to replace the part upon receipt. Now it needs the 3rd part since it is still not working. I have a herniated disc in my neck and had to remove everything from the refrigerator and freezer to take downstairs to salvage our food. Now I have to go through the same thing again for the 3rd time after the additional part comes. This refrigerator is junk. I asked Lowes for a new replacement but of course was denied. Does anyone know a good lawyer for this type of situation? I never had a problem with an appliance like this.

Whirlpool Cabrio Model WTW6500 - I ask all of you to stay away from the Whirlpool Cabrio sets. I have spent hundreds of dollars trying to fix my washer. I just spent $260 for a computer board. Now it stays on rinse cycle. So now I need the motor sensor harness which is another $90. Service call $80 x 2. So, now I am going to take the computer board back and get my 260 dollars back. For the cost of $400 to fix this washer. You can go and buy a new one for around $400. Then, Im going to the lawyers to file a class action suit against Whirlpool. So, owners; be looking in your mailboxes for a class action suit against Whirlpool for those who own the cabrio set. Im tired of having to deal with whirlpool customer service. Maybe, whirlpool should think of having their laundry made back in America.

I couldnt wait to get a front loader and hated it. As soon as I saved up enough money, I bought the water saver Whirlpool top loader. I love it! The clothes get cleaner and dont smell musty. Im very happy with whirlpool.

Aqualift self clean oven??? I followed the directions on how to clean my oven. I wiped and scraped out spilled residue from the oven. Then started the cleaning process. The sides of the oven were not cleaned even when I wiped them with a damp cloth. Scrubbing and scraping with the tools that came with the oven helped somewhat. The bottom of the oven was not cleaned. I had to continually scrub and scrape to get it looking half clean and even then, there were still spots that would not clean away. I would have preferred an oven that uses oven cleaner, it gets the oven much cleaner and with less scrubbing on my part. All in all I am very dissatisfied with the oven and would never recommend it.

Whirlpool duet steam model: WFW9750WW00Serial: CSY3601165Please see attached the pictures of our washer that was purchased without a top counter balance from HH Gregg in May of 2010. We were told by the extended warranty technician when he came to diagnose the machine on 6/24/13 that the bearing and basket were bad. He ordered the parts and returned on 7/2 to repair the machine. Upon taking it apart, he discovered the top counter balance was missing and was the reason that the bearing and other parts had failed. I will include pictures of the plastic that the counter balance should have been attached to. You can see there are no screw holes or scuffs on the plastic. It was suggested by one of the customer service agents, Kitty in TN, that we remove the counter balance. Per Kitty, Because had it come from the factory like that, it would have walked all over the laundry room and not worked right since the first day. Honestly, we have scuffs all over our walls and my husband just thought the legs needed adjusted or it wasnt sitting properly on the pedestal. We have never owned a front load washer, so we didnt know what to expect. The washer sits in a very tight space under the cabinets, but will walk in the middle of the floor especially before we installed the pedestal.The top counter balance was ordered on 7/2 and we were told it would arrive and be installed today. The technician called me at 10:55AM today and stated the package had not arrived. We are asking Whirlpool for a replacement washer as the one we purchased brand new came from the factory defective. We have been told a solid NO. Upon further inspection of the machine while taking pictures, I noticed that the bottom counter balance is cracked clear through as well. Im attaching pictures of that. I did speak with Laticia in MI. She was VERY nice and more empathetic than the other 6 or so people we have spoken with at Whirlpool customer service. She was professional, helpful and I hope who Whirlpool would want representing their company and brand.We feel Whirlpool sold us a faulty machine and they should replace it. We have been told by them that they are sending the parts as a GOODWILL gesture, and will have the parts installed. Now after the whole inside of it is shot and possibly the motor and boards, thats awesome. We are now an LG/Samsung family. This was our 3rd and last set of appliances from Whirlpool. When the rest of these die, we will replace with another brand. How sad that what once was a great company, and I grew up with my mom and grandma thinking there was no other brand to use beside Whirlpool, now we are left washerless for 3 weeks. They refuse to stand behind a mistake that was made in the factory. Ive read these are made in Germany. Maybe Whirlpool needs to bring jobs back to the US and improve their quality control.

We have had a Whirlpool hot water heater for 6 years and 14 days. Note the 14 days. It has been nothing but trouble and we have called the company repeatedly for help. It finally stopped working altogether 14 days after the warranty ran out. Thank you Whirlpool for nothing! It had a filter on the bottom of the heater that constantly had to be cleaned which was next to impossible. We had to buy a special brush to try to reach it. My husband had to take it apart several times a year and clean it to keep it running. Whirlpool should have replaced it within the first year but instead offered many suggestions about cleaning and etc. so they would not have to replace. Today it is out of my house for good and I would advise anyone reading this to beware! Horrible product!!!

Ice maker will freeze up every couple of week. I cleaned it all out last Saturday and today, Friday, it was frozen up again.

Bought a Whirlpool washer and dryer in 2/2013. In 5/2014, the washer went out of balance, but corrected itself quickly. Since then, it sounds like a cement mixer during the spin cycle. It took one month to get someone to come out and look at it. Apparently the bearings went and the part alone costs $450! Add another $250-$300 for labor and I could buy another washer. We called Whirlpool, who were unwilling to do anything to rectify the situation, i.e., replace the washer, send a replacement part, give us a discount on the replacement part. We didnt buy the extended warranty because who would think that a brand new washer would crap out after 15 months... and theres only the two of us.Not like Im washing clothes for a family of 5! I only needed a new washer/dryer because I moved out of state and didnt want to move the ones I had. Regretting that decision. Its unfortunate that there has been a decline in the manufacturing of goods to the point that they can be considered a throw away item. Will NOT be replacing this with another Whirlpool.

I have bought a top load 6.2kg washing machine 3 months back. But now almost all the plastic parts are having a cracks. When I asked for replacement they said plastic parts are not covered in warranty.

I just purchased a brand new refrigerator from Whirpool and after 2 weeks been delivered I started having a lot of issues. They sent a technician twice to get it FIX but Im still having the same problem. And they dont want to replace the unit. They want to keep sending technicians to make the same repairs. Its a NIGHTMARE!! Please do yourself a big favor and buy a different brand. I dont recommend!! By the way this appliances are made in MEXICO!!

These are the worst sets in the world. We bought this set from a hometown store, had them 6 months and all belts on dryer had to have the belt on the dryer replaced, then 2 months later the washing machine went out, so the store did replace both and weve had them about 3 month. The dryer works great so far, the washing machine on the other hand not good at all! The tray where the detergent goes continues to have mold/mildew in it, the clothes come out of wash cycle smelling soured. We have this set inside and we keep our temp set on 67 in our home. There is no excuse for all the problems, not to mention that noise it makes when it washes!! I am completely disgusted!!