We bought a new Whirlpool Cabrio Platinum washer and dryer in July of 2014. We were continually finding wet areas in our clothes after they were supposed to be dry. We finally called Lowes where we purchased the set. We had bought Whirlpool appliances about 10 years ago and were pleased with the product as we never had any problems. Lowes sent a service technician on September 12th who checked out the dryer and told us there was nothing wrong with the dryer, but the vent was unsatisfactory (he was from A&E Appliance Repair). He said there was nothing he could do and charged us around $148 for the 14 minutes he was here. We checked out the vent and found it to be working satisfactorily, but we continued finding wet areas on the clothes that were supposed to be dry. We continued to call Lowes and finally spoke to Amy at their Headquarters Customer Care Dept. with no positive results. We then called Whirlpool, and they sent someone who replaced the steam dryer valve which he said was leaking in November (it took another month to get this part). It is now January of 2015, and we are still experiencing wet spots on our clothes even worse than before!

We have had this microwave 3 years. The first thing we noticed was that baked potatoes were way overdone and nothing heated up correctly when using the sensor Not a big deal - just stopped using the sensor button. Now, we keep getting the open/close door message keeps coming up. I have done all the recommended fixes with no luck. Now we need to have a repairman come out to fix it. It seems when you are paying over $300.00 for a microwave, it should last longer. If I had known it would be such a poor quality, I would have bought a less expensive one and definitely a different brand. We do not use a microwave on a daily basis, so it certainly did not crap out from overuse. I would not recommend this to anyone. Save your money or you will be spending much more on repairs.

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

Unfortunately, I can not rate this machine LESS than one star. I would rate it ZERO. We purchased the Whirlpool Cabrio washing machine model WTW7800XW0, 2 1/2 years ago in 2011. Since that time, we have had nothing but trouble from this machine. The machine basket gets off center when you have heavy items in there like jeans or a large load of towels and just stops working until you raise the lid and even out the clothing in the basket. If you wash something like a throw or a set of sheets in it, they get all twisted and wrapped around the thing in the center and end up in a big mound. We have had the glass top lid replaced on this machine TWO times over the last 2 years because the plastic frame on the lid around the glass cracked and broke and became warped in a raised position. This caused the machine to stop working because the machine will not wash clothing unless the door is locked down, and the door cant lock if the lid is cracked and warped and broken. So you have to set something heavy on top of the lid to get the lid to lock so you can wash a load of clothing! TWO times we have had repair people out to our home to replace the lid and now the lid is cracked and broken again, for the THIRD time! This is THREE broken lids in just over 2 years. Unacceptable!! The hinges on the lid that attach the lid to the machine are also rusted. This rusting has happened on all the lids that we have had replaced in the last 2 years. I will never, NEVER purchase another Whirlpool product again, EVER. Their products are inferior quality and JUNK. We have the Whirlpool dryer also to match the junk washing machine and the quality is just as bad but we are living with it because we have no choice right now. It takes 2 hours to get a load of clothing dry and forget drying jeans or towels; it takes forever! Whirlpool makes a dreadful product and their customer service is even more dreadful. =(

Love my new Whirlpool Refrigerator! Works well and no problems for the last year. Filters are pricey but found some at Lowe’s cheaper. Whirlpool stays in touch frequently emailing information about their products, some useful some not applicable. Would I buy this refrigerator again? Yes, I love the ice maker, it is quite large (enough to fill a small cooler), and the convenience of crushed or cubed ice is nice. Most people complain about the motors are loud yet we have not experienced that.

I purchased the 19 cu. ft. Whirlpool Estar refrigerator WRT 3595FYW on 4/28/12. Freezer began showing frost immediately. Repairman from Marcellas Appliance where purchased - (518) 381-1957, came to check it, put a sealer around the door openings of refrigerator and freezer. Frost continued. I called Whirlpool. They sent another repairman from EB Russell in Schenectady, NY, door needs replacing. Door was ordered and when received by them, the door was replaced on my refrigerator.In August 2012, frost is in freezer, on its roof, on the door daily. I called Whirlpool. I told them I wanted to remove it from my home. Whirlpools reply was, you have a repair warranty, not a replacement warranty. I was not advised of this when I purchased. Otherwise, I would have gone to Sears, Lowes, etc. On 8/16/12, another repairman from The Appliance Man, Albany will be here Monday. Its dishonest sale, replacement was advised possible by Marcella, that it was just a matter of course to get an okay from Whirlpool. This is not so. There is no replacement or return policy. Please help. Thank you.

Whirlpool Double wall-mounted Oven model#WOD51EC7AW05. Have had nothing but problems (at least 7 problems). The 1st one is a potential fire hazard. Porcelain/enamel shattered on bottom interior panel of BOTH ovens in less than 60 days (exposing underlying metal to rust). Cracked in an odd stress-pattern that indicates the metal expanded during heating, and the porcelain finish did not tolerate the expansion. The lower oven had only been used 2X before I noticed the fracture pattern. Obviously faulty design; a manufacturers defect. Whirlpool claims it is cosmetic damage and when porcelain eventually flakes off, they will send me touch-up paint. (If I dent the outside of an appliance with my wheelchair, thats cosmetic damage. Its a manufacturers defect if the damage happens during normal operation. The appliance damaged itself, not the user.)The preheat function does not work on either oven. The oven indicates it is 350-degrees, when it is actually 125-degrees. Repairman says this is normal; ignore the indicator and navigate by store-bought thermometers”. The temperature can vary 50 degrees on either side of the actual setting (thats a 100 degree range!). Between the faulty preheat and the wide range in temperature, it makes it very hard to bake bread or cake.The rest are annoying problems: The timer is a single “beep” (not even very loud), followed by another single beep every minute. This is not much help if you are folding laundry while the cookies bake. The windows have so many dots on them theyre not clear enough to see how the food is cooking (or read the store-bought thermometers) without opening the doors. The oven produces a lot of steam that fogs up the windows (Ive never had this happen, and Im past the half century point). The exhaust fan is loud and it blows hot air into the drawer under the oven (another potential fire hazard). Dont buy this oven. It has several design flaws and Whirlpool does not stand behind their product.

I purchased the glass top Cabrio a couple of years ago. Without an agitator; it is amazing how nice thick towels come out with holes or rips! Clothes get so twisted. My sister needed a new washer and after telling her the problems with the Whirlpool; she purchased an LG. I have told many people that have purchased an agitator free machine to stock up on Affresh or one of the other tub cleaners... you need them to keep the odor from getting into your clean? clothes. I cannot wait to sell this washer or give it away!!

We purchased the Whirlpool Double Oven Range model GGG388LXS in April of 2011. The reason we purchased the oven is that we are empty nesters. We almost exclusively use the small top oven. We have streaks between the double glass on the bottom oven. We can not clean it. It is obviously a design flaw. I looked on this site to see if others have the same problem as it is too early to talk to customer service at Whirlpool. How have others fared with this obvious flaw?

I purchased a Whirlpool oven 14 months ago. I just paid it off 2 months ago. The oven stopped heating. I talked to Whirlpool... and basically because I did not purchase the extented warranty I am SOL. I will never buy a product from them again. Complete junk.

The Whirlpool duet model wfw9150ww01 washing machine is a piece junk. After using it for two years, the bearing has gone out on it and it sounds like a freight train. It will cost $600 to repair it. We only paid $575 for it. What a rip off. Whirlpool makes junk only. Buy something else.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

I bought a new washer and dryer 2 years ago, it was built by Whirlpool under the Kenmore name plate. In the first two weeks we had them come and service it as it was very loud in spin mode. The serviceman said they were all like that. Now, two years later, it is so loud you cannot even carry on a conversation while in the spin mode. Called for service again. After two minutes he says, You better buy a new washer, this one will cost over $800 to fix. Never will buy another Whirlpool appliance or Kenmore again. Buyer beware!

All JUNK!! Replaced all new within the last two years. The washer I replaced was twenty + years and was still working fine was just upgrading, big mistake! Washer is sounding like it is going to walk out the door. Replaced dishwasher after twenty years and the new one was leaking within one year and recently got replaced. The new one did not last one year and also is leaking. Now washing dishes by hand. Lastly replaced hot water heater and that is junk too. Has six year warranty after one year pilot light wont stay lit, Whirlpool said would replace the gas control valve for free but I need to pay to install. I WILL NOT PURCHASE ANYMORE PRODUCTS FROM LOWES OR WHIRLPOOL AGAIN!!! HOW CAN A RETAIL COMPANY REPRESENT SO MUCH JUNK?

My wife and I bought a Whirlpool Cabrio washer and dryer set less than three years ago. And so far the dryer has been ok, but our washer has had to have a new motherboard and now it smells like its burning. Our last washer and dryer set was a hand down and was over 15 years old and never had any issues like our new ones do. Ill never buy another Whirlpool product again.

Bought a whirlpool refrigerator in 2015, have had both handles replaced 3 times, the bottom pieces of the handles are made of plastic and they crack. We had to take them to a metal fabricator and have them replaced with metal to keep them from breaking. Lowes and whirlpool know of this problem and they do nothing about it. Will not buy another whirlpool product. Very dissatisfied.

I purchased this washer model WTW4950XW0 new. Within 6 months, it stopped spinning and was repaired under warranty. The spin actuator was defective. Great. A few months later, it stopped spinning, repaired under warranty and the spin actuator was bad. A few months later it stopped spinning, repaired under warranty, and the actuator was bad. Great. Another few months it stopped spinning again. This time, Whirlpool sent someone to repair it, another bad spin actuator. This time we had to pay for the part. So now that we are completely on our own, it stopped spinning yet again. Let me guess. The spin actuator is bad!!! Incredible. What a piece of crap. This washer was never used heavily.

We bought a new oven/range in April 2019. December 7th 2019 it stopped working. No power at all. We contacted Whirlpool about our unit as it was still under the year warranty. They contacted their local repair company. 3 times they have said they were coming out to fix it and they had the part. Three times they have told us never mind. They didnt have the part and would have to come later. Most recent update, they wont get the part until the 20th and wont make it out until the 23rd. That is over 2 weeks after our unit broke and it is the holidays and we will have family visiting. We have tried to get answers about what is really going on and we keep being told they cant help us or give us any answers. So frustrated. You can bet I will never buy another Whirlpool appliance again!

I purchased Whirlpool Washer WTW4815EW on December 29, 2015 for my tenants apartment and by October 7, 2016 it was not working. I called Whirlpool for service since the product is under warranty. The closest appointment was more than 2 weeks out. On the appointment date the technician called me and said he was on his way to my house which is more than 30 miles from my tenants apartment. The technician said he could not service the tenant area as that was a different group, so we rescheduled for a week later. A week later no one shows up, so I rescheduled yet again for November 3rd and drove myself to wait for the service person who was supposed to be there between 8 am to 12 PM. At 11:40 I saw there was a 10:36 am Whirlpool attempt to call me but no message was left. When I called back they told me the technician called in sick and they called at 7:30 (my iPhone indicated 10:36 am). Now they say someone will come on Saturday November 5th. It will be one month on November 8th with no working washer. While it is bad enough the washer stopped working in less than one year their service support is even worse than the product.

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

My husband and I purchased this washer in August of 2011. Within 2 years the lid broke because of it a cheap plastic frame on a heavy glass lid. At that time I researched it and found many people with the same complaint. Whirlpool would not do anything for us but the company that we purchased it from did agree to supply the part if we paid the labor. We did this and replaced the lid. Well here it is just right at 2 years again and the lid is completely broken and the washer is unusable. There is no way to bypass the lid issue which makes the washer completely useless.I called Whirlpool again and was told there was nothing that could be done and that because there was not a recall on the product, they would not be able to do anything for me. We have purchased a new Samsung washer that received excellent reviews from Consumer reports and we will NEVER buy another Whirlpool product again. I cannot believe a company that old and as large as Whirlpool will not stand behind a faulty design and faulty made piece of equipment. It is very disappointing.

I purchased a Whirlpool fridge in September of 2015. In March of 2016 I noticed the Fridge portion was getting too cold. By April 2016 the freezer stopped freezing and fridge started warming up. I reported the issue to Whirlpool and made an appointment. The day of the appointment the first company called and their tech couldnt make it because of a family emergency. They sent another company out instead. That company diagnosed the issue as a faulty chiller and ordered the part and told me they would be in touch. A week goes by with no working fridge and I call them. They say it will be another week for the parts. Two weeks go by - no call. I call them and they say they have the parts and I make an appointment.The day of the appointment I call them to find out what time they will be out and they tell me they dont have all the parts. And when I mention that I have been without a fridge and that I am frustrated that they arent calling me and that I am having to call them back the lady starts yelling at me asking me if I want to cancel my appointment. So I call Whirlpool and ask for another company. They send a company out that is not trained to be working on a sealed unit. So I call Whirlpool back again and they send an in house tech out three days later. This is over about a month without a fridge at this point. Their tech simply recharges the system and says that it should be fine.A week later the freezer stops freezing and the fridge warms up to the point that both are not usable. The tech comes out and diagnoses that there it is most likely the chiller because of a build up of frost in the freezer. Orders the part and a week and a bit later I call Whirlpool up to get an ETA on the parts. They say they have the parts now (no call??) and they schedule an appointment. The tech comes out and puts the part in almost a week later (2 months now) and says that it is still building up frost in an area that it shouldnt and calls tech support back and forth for the next two hours. He leaves saying give it some time to see if it works, but admits to me that it is likely it is leaking in an area that he cant access.So I call up Whirlpool and explain the situation and ask for a new Fridge. It has been two months and the tech by his own admission could not say he fixed the problem and thought the problem maybe somewhere else. After looking at my case and me being on hold back and forth for about a half hour the supervisor says that at this time I need to wait to see if it fails again. And that if it does I need to have a tech back on site to verify. So this will be the seventh time I took time off work, it will be the fourth time the fridge fails and that I will have to throw out groceries. When is enough enough. I am into this now for almost double what the fridge is worth in lost wages and groceries.Do yourself a favour and stay away from Whirlpool!!! If I have to guess the following will happen: five days from now the fridge will stop working again (when the Freon leaks out - same timeline as previously) and then I have to call for a tech (3-4 days) and the tech will come out, determine that it isnt working. I have another conversation with a supervisor asking for a new fridge and they miraculously agree (yeah I know). Then what two weeks, a month... before I get a new fridge. I anticipate that I will have been without a fridge for 3 months before it is all resolved. Ridiculous is all I can say. Whirlpool should be embarrassed.

Although stackables are a little pricey, Ive had this dryer for around 10 years and its still working just as good as the first day! Never had any repairs done on it. Great dependable dryer and washer!)$ Ive dried regular size loads in it also! A loyal appliance through and through! Thanks Whirlpool for such a great and dependable product! Whirlpool Heavy Duty-Automatic Dry Miser-End of Cycle Signal*3 Cycles.

We bought a Whirlpool refrigerator in January at Home Depot. In July we started noticing that the freezer doesnt work. The ice maker doesnt work, everything melt away. Frozen items were lost. We constantly have to dry the floor since it is leaking water. We called whirlpool on July 27 and they send someone to check it out the following day. He reported that we need a new freezer door. I call for a follow up, I was told that it will take 6-8 weeks before we get a new door and part for the ice maker. We recently called to follow up on the status of the door just to find out that the order didnt get process until mid August. In the meanwhile, the fridge is having condensation. Water is everywhere inside. Fruits are being rotten because of too much moisture. We called again and they send out the same technician. The technician reported that the fridge will not work properly until freezer is fix. We call whirlpool again just for them to tell us to wait for the part, and gave us an extra 6 month warranty.

I have Whirlpool 40 gallon heater 5 years ago. The pilot light went out and I replaced the parts. This has happened three times and I have replaced the entire thermocouple assembly three times. The last time, the parts came straight from Whirlpool. This time, the pilot light will not stay lit. I am on my way to buy another hot water heater for my family because I have had enough.

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

I purchased this rather expensive gas range and use the oven very little. We are empty nesters that eat out every day. Went to use oven and it had error code for cooling fan. Called repairman who replaced sensor and oven worked (literally used two times in 4 months). Now error code again. When I checked the code I realized this is a problem with these stoves. Whirlpool why no recall or free fix?

We purchased a Whirlpool Duet front load washing machine Model #WFW9550WL in July 2009. In July 2016, the guide on the door hinge broke, making the machine unusable. When performing a national search for the part number (#8183202) to replace the broken hinge, I found that there were none available anywhere in the United States. When talking to Whirlpool, they indicated that during 2015, they only sold 142 of this part, and were currently looking for a new manufacturer for the part. They further indicated that the part would not be available until late September or early October of this year.

Bought the hot water heater, installed it. It leaked from bottom. Whirlpool warranties it. Replace it with new heater. It too leaks. I Google problems with Whirlpool hot water heaters. Found over 1500 complaints.

I have a roughly 2-year-old 30 Whirlpool electric range that has just got out of warranty 4 or 5 months ago. It has been a great stove up until the last couple of months. We have had 4 incidents where the burner would shoot up to high on its own even with the knob down at medium or low. 4 times in the last month, it has come close to catching fire while we were cooking. I have contacted Whirlpool about this issue and have yet to get a response.

This is my first electric range. It’s amazing! It cooks evenly and at the exact temperature! The stovetop has size adjusted burners, again at the precise temperature. And the look is very sleek & modern, perfect for a new kitchen! I am so very pleased.

Purchased this electric range Maytag model YMES8800FZ1 in September 2017. Thought it was just like my old range with self cleaning mode. Beware! Do Not buy this or anything with this new AquaLift self clean technology. That means youre down on your hands and knées, scrubbing. It doesn’t work. Read all the reviews about this new technology. Salesman never informed us. We innocently bought the range with self cleaning, paid lots of money, for crap! Very upset. Will spread the word for all future buyers, pay attention to the self clean mode on what youre buying, cause no one will tell you. Now trying to reach Maytag, but apparently they don’t care.

We purchased a new home in July of 2011 and we paid extra for the upgraded appliance package, which included a Whirlpool Microwave/Convection Hood Combination unit. We have Model # GH7208XRS3. We use the microwave a few times a week and only used the home 6 months each year during 2012, 2013 and 2014, for a total of approximately 18 months. From the very beginning, we had trouble with the microwave control panel turning itself on and the electronics going through various timing and programming functions independent of any human operator.During the combined two-year warranty period from July 2011 July 2013 (the Manufacturers Warranty lasted one year and the Developers extended Warranty lasted an additional year) we had 5 service calls on the same issue. The Authorized Repair Center repairman called the Whirlpool Tech Line while he was in our home and was told that there was a flaw in the design of this model. They replaced the door and then when it acted up again, they replaced the control panel. In Nov. 2012, after the repairman told us the door needed to be replaced again, we asked for a new appliance since we had the same issue repeatedly and they had already tried to fix it by replacing the door and it was still under warranty. We were told that Whirlpool would not replace the appliance until they had tried to fix it three times and we needed to get a new door again. We were told that because it was the same issue repeatedly, we would get a replacement if it still went bad after the warranty was up. So we had the door replaced again, which did not fix the problem.In late 2014, we again had the same issue with the control panel and made a call to Whirlpools Customer Experience Center. At that time, we were told that the warranty was no longer in effect and Whirlpool would do nothing to fix the issue. Even though it was the same issue that they had attempted and failed to fix while under warranty, the company would no longer stand behind the promise of customer satisfaction and told us they will not replace a 3-year-old microwave. When I asked the Customer Service Rep to speak to a Manager to escalate the issue, I was transferred to the Tennessee Office. When I got the same repeated run-around from the Supervisor, Melissa, I asked that Customer Service Supervisor to let me speak to a Manager and she told me she could not give me the name of anyone else to speak with and hung up on me.I am writing to you to express my extreme disappointment in Whirlpool and the products reliability, the way the company has handled fixing the problem and especially in the conduct of the Customer Service department. Whirlpool gave us nothing but a run-around for the years the warranty was in effect, knowing that this model has a design flaw and trying to do band-aid fixes until the warranty ran out. We were told that our only option now is to pay to have the same problem fixed a fourth time or purchase a new microwave.Whirlpool has trained their Customer Service people to be polite but ineffective and obstructionist on the phone and then hang up on the customer when they cannot resolve the customers issue. I believe that Whirlpool should be committed to customer satisfaction and making sure that their products work as intended and fix the problem that was reported while under warranty, even if it no longer in warranty. Whirlpool should be as disappointed as I am that after three attempts the problem is still not fixed and should be committed to customer satisfaction enough to replace the appliance after three failed attempts.

I purchased the Whirlpool Cabrio washer and dryer about 5 years ago. I wanted to pay for a good pair to last a long time for the money. We have had a repair man out twice for the washer. They ended up replacing the computer board. It worked fine for a few years. Now, it keeps getting the unbalanced error code for almost every load of clothes that we start. Sometimes, it takes 20-30 minutes of rearranging the clothes to get it to finally work. I have had to manually set it to finish the loads on a number of occasions. It is so time consuming to do laundry due to having to play with the clothes to get the loads to finish. Plus, I dont know how many times it has woken up my grandkids because of the loud thumping noise it makes when it gets unbalanced. I have never had a washer do this. I would expect when you pay big bucks for an appliance that it should last a long long time. One usually gets what they pay for. I should have bought a cheaper pair. Then, they probably would have lasted 15 to 20 years.

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..

We bought this washer on 9/05/09. Recently, it sprung a leak due to a worn out seal that the repairman said would cost more to fix than just getting another washer. You would think this might be cause for distress, but I literally jumped in the air and clicked my heels with joy! This washer has been nothing but a pain. First of all, I have to pre-soak every load before washing or the clothes come out just as dirty as they went in. I would set the timer on my stove to let me know when the 40 min soak cycle ended so I could change it to wash. Then I reset the timer for another 40 minutes. I also learned the hard way, that using any kind of heavy duty setting would turn towels into a pile of yarn. This washer cost $998, and guilt is the only reason I didnt replace it years ago. Ding Dong the washer is DEAD!!!

We purchased a Whirlpool side by side from Lowes and an extended warranty. Immediately maybe a month the ice maker froze. Ice container in the door. Repairman said design is notorious for this problem. This was an ongoing problem. They replaced icemaker and it continued. Finally the warranty people told me it could be deemed a lemon if repaired for the same issue 4 times in a year. They deemed it a LEMON and I received a store credit for the purchase price less the warranty amount. I purchased a new LG French door. No issues and its been 5 years. If you have an extended warranty do some checking on the lemon.

I purchased a Whirlpool fridge brand new. Not even a freaking yr old it went out!!!! Repairman came out and said it had leaked crap all over really. He said it would be too much to repair. Better off on purchasing a new one.

I purchased a washer 6 months ago and it was starting by itself so I called to get a technician out and it took them 3 days to tell me that they did not service in our area. Long story short I was out of a washer for 2 weeks talking back & forth with Whirlpool which was absolutely a nightmare. Kept me on hold forever and hung up on me several times so they didnt have to deal with the situation. Absolutely no customer service at all. When it came down to it they were going to issue me a new washing machine and I had to go to the store to get it and when I got to the store they told me I had a $415.00 credit to spend. Thats less than what I had paid for the washing machine and then I am having to spend an extra $200.00 out of pocket to get another washing machine.My warning to you is not to purchase any Whirlpool appliances unless you want to go thru pure hell. These people do not care about anyone after the product is sold. Their customer service sucks, their appliances suck and Whirlpool just sucks all the way around!! Worst experience I have ever had and I hope they never sell another appliance again!!

Bought this model #WTW8500DC from Lowes in 2015. Ever since had problems. Stopping in the middle, not starting, recently keeps running water, lid lock issues, had multiple service calls and multiple hardware changes, paid extra for extended warranty from Whirlpool hoping that within a year all problems would be gone after so many repairs. Boys I was wrong. After spending around $1200 between this machine and the extended warranty, three year later after the warranty expired now I am stuck with this non-functional piece of junk and looking for another washing machine. Would love to hear from Whirlpool if I stumbled upon a lemon, or three year is expected life of their $1000 plus machines.

Purchased on Nov 2010 at Lowes. Washer machine sounds like an airplane on the wash and worst on the spin cycles. Bearings are gone!! Customer service was no help. Basically was told I was ** out of luck. Have service bulletin addressing this issue, yet they refused to help. $1300 learning experience about Whirlpool. Social media here we come. Goal: to keep at least 1 million customers away from their scrap!!

I bought a range on 2/11/11. On 2/14/12, I cleaned the oven for the first time at high temperature and noticed burned grease marks which appeared at the inside of the glass in front of the oven. I called for service and the repairman took apart the door and cleaned it. He said it would probably happen again. There was a leakage somewhere and he couldnt repair it. I think it is a quality control problem at the manufacturing levels.

After 2-1/2 years we started having trouble with the spin cycle on our Maytag washer. We live in an area with no repairman. Whirlpool want us to pay just to talk to us. Now the timings off. It will not spin out.

We purchased the Whirlpool Gold Series smooth top stove from Lowes in December of 2013. The stove is not even 2 years old and it doesnt work. Last September, I noticed a few times that while baking food in the oven, it was burnt after only 10 minutes, due to a runaway temperature. After that, the oven wouldnt heat up properly, it would take too long to bake anything because the temperature wouldnt reach the reading on the display. Then it just stopped baking or broiling all together with the error Feature unavailable. Weve had a serviceman out at least 3 times. Of course, the warrantys run out and its cost us close to $500 to keep fixing it, and two motherboards and a bottom element later, its still not fixed. They wanted to order 2 more parts at our expense, but we cant continue trying to fix this lemon. I will be shopping for another oven, and will never recommend Whirlpool to anyone.

My Whirlpool Cabrio WTW7800 was bought 1 and 1/2 years ago. The lid is glass with a plastic edge. The plastic part of the lid next to the glass and hinge is cracking causing the glass to stick up. It is cracked from the top of the lid toward the base if the lid were closed. The only way this could happen if it werent a manufacturer defect would be if someone were to get inside of the washer with the lid locked and try to push up to get out right at the hinges. I have noticed several other complaints of the same problem on this website with the same model. Clearly this is a manufacturer defect. I am on the phone with Whirlpool now.

This machine does not clean the clothes well, keeps an odor even after using Clorox (probably due to water inside that never leaves), and does not spin the clothes well. Every washing is longer than traditional washers and then I must use the spin-only cycle twice (adding another 30 minutes). I must also shake the inside of the tub to get the spin to work at all. The tech came out and re-calibrated, but to no advantage. Terrible machine and should be, as one viewer said, under recall, in my opinion. NOT WORTH THE MONEY -- and I am very disappointed in Whirlpool.

I purchased a Whirlpool refrigerator from Gerhard’s Appliance, Glenside, PA on 12/15/2011.There have been problems with the unit since it was delivered on 12/19/2011. The doors were not the same height. There were stains (which looked like rust) on both doors. A shelf on the door and one in the fridge were missing. One of the deliverymen adjusted the door height then, and the door has been creaking on opening/closing since. That door has been replaced, but the problem continues. The freezer (which has an icemaker/water dispenser built in) started to produce ice on the inside of the unit door and on the wall surfaces. Attempts made to rectify the problem were unsuccessful. A new freezer door was ordered. After the door replacement, the frost problem got worse. I can fax you a copy of all service contacts so far (at least 7). Please help me replace this lemon.

Found after care service as bad as oven performance. Phoned for advice and told need to get used to new oven. My advice would be do not buy whirlpool ovens.

55 Gal Electric New in 2003 / Limited Lifetime Warranty - I paid quite a bit more initially at Lowes for this unit. Its stainless lined. I have had numerous problems since purchase. I had to replace the sensing element in the Smart Box in 2006. Then the lights started flashing again making a humming sound in the box. I took each piece apart in smart box and cleaned them, which seemed to help. Then the upper element that is also stainless that requires a special wrench to replace went bad according to the blinking lights. Lights stopped after several resets. Now, the water is boiling out of the top of heater and they tell me its the seal in the element that I never replaced. The cover for the element is off. Water cannot possibly build up and force out the top of the cover of tank. I am not an idiot, yet they tell me that is most likely the problem. They didnt listen to me long enough to properly assess my concern. Every plumber I talk to says its the separation of the liner inside the heater. Nonetheless, I have a water problem now in the basement and have never heard back from Whirlpool as promised with troubleshooting guide on an email. I am sick of calling and getting the runaround with every issue. The warranty is horrible for the consumer. Sure, you have a limited lifetime warranty, but when you cant get proper information when you need it, what good is it? Made in America is why I bought the product. I also need a new washer but will not be searching in the Whirlpool line due to their lack of care with an important issue with my heater.

We bought our washer about 3 years ago brand new from Lowes. Like others, I have had problems with holes in clothing and spots that looked like grease. It worked well up until recently when we noticed some brown splatters on the floor. Shortly after it made a loud noise like a plane taking off and the load would become unbalanced. We researched and found many people were having issues with the bearings going bad. My husband was going to order parts to fix it but you have to have a special tool that is expensive to buy... It was going to be almost $200 to repair ourselves! He called a washing machine repair man and he said he doesnt even touch them because the repair wont last. I guess were going to be better off buying a new washer. There really needs to be a recall on this product!!!

I purchased a Whirlpool Cabrio washer and dryer from a local appliance center. Everything was working great. After some time, the washer began to have error codes. I would have to turn it off and restart using more detergent, more water and more electricity to attempt to get a load washed. I did purchase an extended warranty. I reported the issue to Whirlpool and I have had 7 home repair visits while still under Whirlpools warranty. The first time, the repair tech went under the washer and tightened a screw. REALLY! The next visit, the motherboard was changed and the issues kept coming back. Well, the Whirlpool warranty was now over so the extended warranty had to be picked up from the appliance center. Things got worse and had continued repair calls. After I had enough, I called Whirlpool and spoke to everyone under the sun. I tossed it outside and bought another brand washer. Several weeks went by and this washer still under the shed, Whirlpool contacted me and bought back my washer, GREAT.Now, here it starts all over again with the dryer, same issues with motherboard. Only this time, I am 1 month out of Whirlpool warranty and need $385 for a new motherboard plus cost to replace. I call Whirlpool again but only this time, they show no issues with this dryer and are not budging. I toss it out and again, purchase another brand dryer. I grew more angry by the day looking at this dryer sitting useless outside. I had it hauled off as trash. My question is how does a consumer protect themselves against these manufacturers? I do understand warranties but if it smells like a lemon, acts like a lemon, it must be a lemon!

Bought a Whirlpool Cabrio Washer, which I see has MANY complaints. I had a problem with the F1 issue during the first year. Same issue and I was also told Whirlpool knows it was bad design yet they refuse to help the consumer in anyway. Maybe 50% a new WP washer. Upon my call they will fix it for 389.00 and give a 1 year warranty again. Im no longer confident in WP products.

Whirlpool WRT351SFYW 21.1 Cu. Ft. White Top Freezer Refrigerator - Energy... puts out a very irritating high pitch noise, unlike my previous Whirlpool fridge. The old one was perfectly quiet. I believe Whirlpool is going downhill in every way. WP is buying refrigerators from 3rd world countries and slapping the name on them. The delivery people were very rude with me when I was unable to give them a tip, even though I had to supply my truck to shuttle the fridge up to my house and help them unload it. I also had to go and find them when they would not follow my directions to my house. So, they kept the wrench I loaned them; they did not have their own tools for the installation. And they refused to return it when I asked them to do so. Denvers Customer Service refused to respond in any way to my requests for information or complaints about the noise and delivery. Finally, their head office contacted me a month or two later, and the customer service person had initiated the discussion in argumentative attitude despite my saying I did not care anymore, I gave up on them and dont expect anything from Whirlpool anymore. While she told me that there are standard levels of acceptable noise that come from their refrigerator, while, she refused to acknowledge that they are not my standards, and I am the customer, besides, I had an older Whirlpool fridge that did not make any noise. I am sorry trusted WP, when I tried to upgrade the old fridge - it was an expensive downgrade! Buy LG or Amana - wished I did!

Model gmh61xvb1 was purchased about 2011 and has had to be fixed 5 times. Now, its down again. My GE microwave lasted 23 years. I thought Whirlpool was supposed to be the best. Boy was I wrong. This has been a real headache. I ordered an LG yesterday. I was in the market for a refrigerator but it will not be a Whirlpool. What has happened to your quality control?

The oven will not turn off. When I called Whirlpool and told them what had happened they immediately put me in contact with the safety division. My question is if it is a safety issue, why is there not a recall and why do I have to pay for the circuit board. If there is a safety issue why is there not a recall.

We bought our Whirlpool washer and dryer set through a PX at Fort Hood, Texas. Took it home, plugged it in and... nothing. Called the service desk, and they sent a repairman right away. He replaced the panel and the water intake fuse (I think? It was a fuse that dealt with the water filling) and then we were off and running. I thought, Great! Now I can wash laundry! After about a couple months, the washer would be so stinking loud in the spin cycle, we would plan outside activities ha ha. Fast forward 2 years, the loud sound continues, but Ive not had any problems. Then, Im washing a load of bed sheets, and just happen to walk past the washer while its spinning... I smelled something HOT and BURNING! Sure enough, it was the washer! I hurried and stopped the spin and unplugged the machine. Opened the door to pull out my sheets, and white smoke comes pouring out of the machine. IT NEARLY STARTED A HOUSE FIRE. I was praising God I smelled the problem. Who knows what would have happened. So I call an appliance shop I trust. They send out a guy who tells me I might as well purchase a new machine because the bearing is bad, and the repair is going to cost $600+. Never again, Whirlpool. Never again. You dont endanger my familys safety in exchange for a quick buck on cheap parts. Ridiculous. And, now that I am reading all these reviews on this website about my washer, I am floored. How is there not a class action lawsuit against this company? Mold and fire-hazards are serious infractions, in my opinion.

I bought my Whirlpool induction stove several years ago. We normally use a toaster oven for baking as we are only 2 in our home. Last year I decided to cook a large turkey for the family. I threw the turkey into the oven and started cooking it. After an hour or so I decided to start cooking the potatoes etc on the stovetop portion. My potatoes started cooking and my element shut down. I did everything I could to get it going but finally resorted to the manual to see if there was a suggestion. The suggestion was that the oven had heated the burners too high and that I had to shut off the burners and wait for 5 minutes and try again to use them. The oven was only cooking at 300F. I waited 15 mins to get it running again. The stovetop went out once again and I had to stop cooking. Conversely Ive had the same issue with the oven. Ive been cooking in the oven and have had it shut down as a way to address the stovetop being too hot. How am I suppose to cook on this unit with any kind of confidence? I did an online chat with a rep today and they suggested getting a technician over to the house. I was told I could pay $129 to have them look at it. This is obviously a design flaw that I was never told about prior to my purchase and would never have bought had I known. Shame on Whirlpool!

Whirlpool Duet $1300, in the past we had great service from other Whirlpool products. Just a more modern look and knowing it was a company we had used in the past with very little or no problems so we expected the same only with energy and water savings. We are energy aware and believe in conserving energy and water where we can. My wife wanted to stick with the brand that gave us good service in the past and chose one of their most conservative units on the market (I believe it was based mainly on looks). What burns me the most about this unit is its constant consumption of clothing, the repair guy found nothing askew with the unit and suggested smaller loads. So we reduced the load size smaller and smaller till we were washing each outfit separately and guess what, it still ate clothes, just chews them up.We lose about a hundred dollars a month in clothing. This washer tears holes and shreds clothing on almost every load, I have to put shirts and lighter clothes to the back of the washer then load the heavier blue jeans and such toward the front and hope they finish in the same position or something is ruined. The fabric becomes distressed, stretched, shredded or has holes, or any combination of the above. We have taken to going to a laundromat or sending clothes to the cleaners. These units are three years old and we are now looking for a replacement for the washer because the local service guy won’t even come out any more. This problem surfaced within a week of the first use of the machine and has remained steady, as we are retired and travel a lot we are not always using them so they are what I would term very lightly used.

We purchased a mid-grade Whirlpool Gold Series dishwasher a little over 2 years ago. 14 months in, the motor failed, requiring a $295.00 repair/replacement. That was nine months ago, and now the motor has failed again. That is outrageous! No more expensive repairs on this piece of junk. Its going to the scrap heap. We just ordered a Frigidaire. While I have no experience with that brand, it cant possibly be as bad as Whirlpool.

I just want to say that this washer is indeed a colossal waste of money. I bought an HE machine thinking Id be environmentally responsible, but the amount of times I have to re-rinse clothes negates that. Whats worse is that clothes come out dirtier than when they go in. Thats right--just put a brand new set of sheets in the washer and when they came out, there were dissolved detergent marks and gray, linty patches all over them (this using warm water and a soft gel detergent)--resembling dirt you might get from hanging clothes on a mildew clothes line. I cant tell you how many times I need to re-run the drain and spin cycle. This wastes time, water and quality of life. Id try to re-sell it on Craigslist but wouldnt want to subject anyone else to it--not fair even at $100!Updated on 02/23/2015I wrote a review in September 2014 on the Whirlpool cabrio model WTW5600XWO. To update the community on my recent customer service experience with Whirlpool: I wrote them a letter a few weeks ago stating that I dont expect them to follow up but wanted to let them know I would be buying Bosh products from now on and reiterating my anger at needing to miracle brush any dark piece of clothing after it goes through the cabrio. My letter specifically said I did not expect customer resolution but wanted to express what a rotten product they produced and marketed. They called back leaving a message to the effect: We apologize want to help you but need to speak in person. Please call [toll free number] and have your make and serial numbers available. I called back, and after waiting on hold for 10 mins., the rep took my model and serial numbers, said, Oh I see your letter. Please give me a moment to review it. Then I was told there was nothing she could do. I do apologize for your frustration. I couldnt BELIEVE they would bother contacting me only to make me go through that charade-- They are PATHETIC! I say boycott the company! Well, I certainly will.

This is a replacement of a similar model, that lasted 23 years. This modest, white, 2 door, side by side refrigerator, was purchased without the optional ice maker. It was bought specifically for the dimensions, of our custom cabinets. There are obvious differences, from the previous incarnation. The textured doors were replaced with a smooth glossy finish and their height extends higher than the refrigerator cabinet. The adjustable shelves were replaced with less adjustable pre fixed shelf supports. The LED interior lighting is much brighter that the incandescent bulbs they replaced. Overall, so far a very capable refrigerator, for a moderately sized kitchen and if the life, lasts as long as the one it replaced, this was a very good purchase.

We bought a Whirlpool Cabrio 2 years ago and they are an absolute piece of junk!!! There is only 2 people in our family so its not like we are washing big loads. It doesnt get my clothes clean and the clothes stink. I have followed the directions on cleaning the washer and it does not good. Now my clothes are soaking wet at the end of the cycle so I have to put it on drain and spin just to get most (not all) the water out of them. And when I take my clothes out, they are just as dirty as when I put them in. Called a technician and its going to cost over $400.00 to fix. This is nothing short of robbery!!!! This machine is a piece of junk. I read over 500 reviews on this washer and they all had problems that cost as almost as much as the washer cost to repair. There really needs to be a recall or a class action lawsuit against Whirlpool.

I ordered this Whirlpool 29 cu.ft. white french door refrigerator online from Goedeckers on April 26, 2013. Delivered May 15, 2013. Ever since we got it, there was a frost buildup in left back of ref. Also ice would fall out of dispenser all by itself. Also a buildup of ice under ice bin. Water would also drip from dispenser. We thought maybe since it was new these problems would go away. But they just got worse. I called Whirlpool & they sent out tech on 8/12/13. He told me Whirlpool has a problem with these refrigerators & would order parts. Well after 3 times of cancelling repairman due to parts on backorder, I told repair I would call when parts come in. I keep calling Whirlpool & keep hearing parts are on backorder, saying parts will be in in 7 days. I call back in 7 days and hear the same lies. Its a shame that they cant get parts in knowing that there is a major problem. It sounds like a real quality control problem. I really pride myself on buying American made but Whirlpool is not helping my case for buying American made. It would be nice if they offered to replace it being they cant seem to find parts.

I bought the Whirlpool WTW 5000DW1 washer and dryer to go with it. Within the first 2 weeks the plastic handle broke on the dryer. Ive been using the corner of the plastic handle ever since to open the dryer. The washer is the worst washer I have ever purchased in my life. The tub doesnt fill up over the clothes half the time. It is perfectly balanced on the floor but it always bounces around and you cannot open it to rearrange the clothes because they lock the lid. The only option is to try to hold it and wait for it to finish or start over by pressing the button for at least 3 seconds. I have had a few items get shredded by it and a lot of times the clothes dont get cleaned and rinsed properly. Even on 2 rinse option. Just the fact that it has a 2 rinse option is a big red flag. It is supposed to be a energy saver and water saver but that isnt true. If you have to wash and rinse the clothes twice because it has spots from the detergent still on the sheets, something just isnt right. Whirlpool shouldnt even put a product like this on the market. I have owned many Whirlpool products before this but this is the last Whirlpool product I will ever buy. Obviously Whirlpool doesnt test its products or care about quality.

Our Whirlpool Duet Washer pair is 2.5 yrs old. The washer didnt work at first, but a repairman found the problem and fixed it right up. They have not broken. The dryer has been fine and we have had them stacked for most of the time without any issues. My problem sounds minor compared to those others listed here, but this thing is ruining all our white or light colored clothes. They go in white, and come out covered with splotchy, dirty looking spots literally all over them! They werent that kind of dirty when they went in. It’s the oddest thing, like it makes dirt. Reading some of these concerns makes me wonder if it has a mold problem inside somewhere, and that is what is ruining our clothes. Tax return is coming and it is going. End of story.

The technician that was here to repair my propane water heater called Whirlpool to get help with the problem. The pilot would not stay lit, they would not help him. I told him it was installed in a mobile home and he had to cap the gas to the heater, it was still under warranty. Later I found out there was a recall on this heater and that probably was the reason they told him that. I ordered a water heater just for mobiles and am in the process of getting it installed. I kept the old heater for now and will still pursue this issue under the warranty.

Originally, I loved my machine. At the one year mark, my washing machine began a f51 error code. I looked it up and it had a recall. The entire board had to be replaced. Now, I keep getting a ul code and it will not quit. Also, the inside of the top is rusting out so badly that chunks of rust fall into the washing machine and stain my clothes. I wish Whirlpool would fix these common errors. I see many other people complaining online that the same thing is happening over and over.

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

We bought a Whirlpool front door open washer machine from Best Buy on Oct. 2, 2011. We didnt start to use until our basement got finished. In November when the basement was ready, we found out that the machine didnt work at all. We called A&E factory service as suggested by Best Buy. They sent technicians 3 times in 2 months to check the machine. Now, it is 3 months later since we purchased the machine, the machine is still not working. We contacted Whirlpool, and they would not exchange to another machine, instead, they told us they will send another technician to check it once again. This machine costs us $800 before tax, but until now, it is still not working. Can you tell us what to do? We called Best Buy and they said this machine is under factorys warranty. So we called A& E service, who said that if Whirlpool called them, they will tell them it cannot be fixed. However, they need Whirlpool to call them because they work for Whirlpool. Is 3 month waiting not enough for a brand new machine to get fixed? And the worst thing is we still owe money to Best Buy creditor. Please help us to get rid of this! Thanks!

I purchased my range, model #WEG730H0DW0 in April 2016. I am extremely dissatisfied with the product and the Whirlpool service. I guess its comforting to know that Im not alone. Ive had two problems so far. The first is with the broiler that clicks on and off. It took several visits and a new electrical board for the service person and me to figure out that the door has to be closed to broil. Not sure about all of you but I am used to keeping the door cracked open to be able to keep an eye on the food being broiled. Apparently there is a thermostat at the front of the oven designed to keep the electrical controls from getting overheated or from melting so when the door is cracked open the heat from the broiler hits that thermostat and the broiler is shut off.The people at Whirlpool are awful and rude. I made so many calls and described the problem in so many ways and not one person knew about this newly placed thermostat or thought to ask about keeping the door closed. It took me and my service tech over an hour of troubleshooting on his SECOND visit to figure it out. He looked up the specs and we figured it out. I wonder how many new electrical boards have been replaced when the solution is as simple as keeping the door closed. A stupid design. Also having the same problems with the knobs. They turn so easily that twice I have smelled gas and realized one of the knobs was turned ever so slightly (before the clicking sound to ignite the stove).Then the third time could have been deadly. I had friends come pick me up and we stood in the kitchen for a bit before we left for the entire day. When we returned the whole house smelled of gas. Someone inadvertently must have brushed up against the stove and the knob turned. My dog, thankfully is still alive and so are we. THIS IS NOT ONLY A STUPID DESIGN BUT A POTENTIALLY DEADLY ONE!! I am forwarding this message directly to Whirlpool in the hopes of getting my money back. I am replacing the range immediately and will never purchase a Whirlpool product again!

Worst refrigerator (French Door Refrigerator WRF989SDAB00) ever! Even though this Technical Service Pointer was issued, it takes forever to get any satisfaction from Whirlpool. They were not pleasant to deal with when calling the Whirlpool Corporation. I had to research the problem while on the phone with their service representatives. The technician arrives and confirms that the evaporator in the fresh food section is indeed the problem but then it takes days for the parts to come in and then another appointment will be scheduled. Whirlpool does not provide good customer service. A refrigerator should last more than three years. Very disappointed and would never recommend Whirlpool to anyone.

I purchased a Whirlpool refrigerator in 2012 and now it does not work and Whirlpool says a 1300.00 refrigerator only has a one year warranty. Please do not purchase a Whirlpool brand because they do not live up to their brand name.

Bought this refrigerator in 2018 and ice maker went out 2x, then compressor went out and waited 4 weeks for part. Now the refrigerator is broken again and not cooling. Dozens of other reviews indicate the same issue with this model. It’s clearly a defective model. Customer service in Tennessee are very friendly but my refrigerator is still not working. Whirlpool French door - wrf954cihm.

Switched to bottom freezer and love the size. We all use and enjoy the filtered water. Whirlpool has proven to be a manufacturer I will always consider when making major appliance purchases for performance, service, and dependability.

Whirlpool Cabrio WTW8500DC0 - 2 months out of warranty, 14 months old. Motherboard fried. $300 if I do it myself. $550 to have it done. The unit was $780 on sale. Brand new piece of junk. Zero stars but thats not an option. Quite honestly, it doesnt clean very well and it doesnt rinse very well so we have to rinse twice to get the smell out if we use bleach. So whats the sense in buying a high efficiency washer? I work outdoors and weve had cheap washers in the past that clean much better and lasted many years.

I purchased Whirlpool Microwave/Convection Oven a little over a year ago. It needed repair four times and the latest repair debacle appears that it will take ~5-6 weeks to get it repaired if the part that comes in works. The microwave model number is GMH6185XVS1. I will never buy another Whirlpool appliance. I spoke with Whirlpool (not the extended warranty company to which I was referred), and they refused to help, period.The extended warranty company (although very nice), werent much help and will continue to attempt repairs until the price of the repair(s) exceeds the value of the microwave no matter how it inconveniences my household.

We purchased a high end KitchenAid Refrigerator Dec 2018. Rust developed on water dispenser door in less than year. They would not honor warranty. Since March we have had ongoing cooling problems with 5 service calls and 4 different fixes and unit still doesnt work. Local authorized service company, Fields, in Jacksonville FL is incompetent. Whirlpool doesnt return calls. The products value is not consistent with the high cost. Here are the gory details. Ref: Setzers, Jacksonville FL (sold unit). Fields Jacksonville FL (factory authorized service company).Less than 1 year in, it began to rust. We called for a Warranty check. Fields Appliance (their factory authorized service company) came out and agreed all 5 doors needed to be replaced. A month rocked on, finally we called to find out where the doors were, and were told Whirlpool (Makers of Kitchenaid) denied the claim. Citing that we lived near the coast! Well, our other appliances arent rusting and the refrigerator doesnt sit outside! They sent us a 6 oz bottle of rust cleaner. A few months later, this refrigerator stops cooling! This was in March, 3 months out of 1 yr warranty. The refrigerant system is warranted for 5 yrs. This was also right at the beginning of Covid 19 shutdown. Fields could not give us a appointment, due to shutdowns. So, I called a local company to fix it out of pocket. He discovered a leak in the coolant lines, fixed the leak and replaced the coolant ($453.61 on 4/9/20). Great, it works! About 3 weeks later, it stops cooling again. Called local service repairman out once more to see whats going on. He replaces a thermal bi metal sensor and well ahh! It works again ($100 on 4/28/2020).About 3 weeks after that, it stops working again! We are thinking by now, its a problem for Setzers, Whirlpool, and Fields. We call the local service repairman out to confirm and he states that the evaporator fan motor will need to be replaced, and that part replaces all sensors as well ($59.99 5/28/2020 service call). We call Setzers and schedule an appointment with Fields. First appointment we could get was 6/16/2020. Guy comes out, and cited a factory defect, per a technical bulletin he had, and relocated a sensor. Simple as that, he assured us it was fixed! Even though I pointed out it felt no cooler when he packed his things to leave. It did nothing! In the background Setzers (when they would call back) were supposedly working with Whirlpool to help fix the problem! Whirlpools reply was that since our repairman was not factory authorized, it completely voided our warranty! Explaining we had no choice, since Fields wouldnt come out and by now we are without a working refrigerator for 3 months, they could care less! Feeling totally frustrated, we call Fields again! On 6/19/2020, they send out another repairman. This guy came in, opened up the back, and immediately stated the refrigerant was overfilled. Didnt do any diagnostics, just told us that we were **, and walked away, without even putting the refrigerator back in place! Neither Fields rep hooked up a diagnostic tool to confirm any real issue, I guess they just knew! Total incompetence! So... As of now we have paid the local repairman ($448.33 on 6/26/2020) to order the evaporation fan motor and install it this coming Monday (7/20/2020). Total amount out of pocket at this point, $1053.90. It took that long to get here! Wish us luck! Setzers wiped their hands clean of the issue and told us to call Whirlpool. We did have not ever received callback.

We started noticing pools of water on the floor on the left side of the freezer. We would then open up the drawer and it was covered in ice. The water was not noticed until the morning so it has caused damage to the floor and molding in our house that was built in 2012. I called the repair company that I used to have my Whirlpool oven fixed (broke twice). That is when the manager gave me the lowdown on what has been happening with this fridge. He told me to call Whirlpool and have them pay for the repair and part and to research online, that it is a design flaw with the freezer and the p-trap and draining under the ice maker being not efficient.I called Whirlpool and complained. All of my appliances are Whirlpool and I spoke to a Supervisor. They only would not agree to pay for the repair and only will pay for the part (which is only $27.00). This fridge is 15 months old and I am irate at the lack of customer loyalty from Whirlpool. They responded the exact same way when my oven broke a month out of warranty. I will never buy another Whirlpool appliance again, and would like buyers to be aware before they buy an almost $2,000 fridge.

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

In the first year of my Whirlpool Washing Machine, the motor quit working entirely. Fortunately, the machine was under a 1-year warranty and the motor was replaced by a Whirlpool service technician. My big complaint with this washing machine is this: Even though you select hot water for the wash cycle, the machine has sensors in it that only allow the water to get lukewarm. If it senses the water getting too hot, it adds cold water to bring the wash temperature back down to 78 degrees F. Next time I will do my research and buy a machine that actually allows one to use hot water.

It’s a great stove. I love the glass top. Only dislike about mine is that it doesn’t have the self-cleaning option. I’m very weak in arms and have back injury so bending over to clean it myself is not possible.

Whirlpool Dryers: I have 2 Duet Dryers and the user interface has gone bad with both several times. I called whirlpool several times to repair. The last time, they refused to repair the dryer. I started having problems with my dryers within the first 6 months of owning them. The repair guy that they sent out the first time said this repair was a major problem with the duets but the company chooses to not acknowledge the problem. They should be required to have a recall. Never by this dryer, you will regret it!

Whirlpool Gold GC3SHAXVBOO - Two issues in two years. We purchased this refrigerator online through Whirlpool in April 2010. Almost a year later, a circuit board went. This was repaired under warranty. Our refrigerator was making loud cycling noises and we were told this was normal. Now a year later, again we have an issue. This time its the compressor. We called customer service and were told there is nothing they can do. The cost to fix approximately is $700. This is very upsetting to buy a $2000 refrigerator and have two major issues within two years and then not have the company stand by their product. I would wonder how many other people have this model and have these issues as it seems like a lot. Whirlpool customer service is terrible, non-caring and offered no assistance.

Everything I buy from this company breaks all the time. I purchased these brands hoping they were good but apparently not. Always have to get them serviced. Lately they did an exchange on my fridge. Hope it helps because after thousands of dollars of food in the garbage it better work. And the washer thought, Oh Im paying more. It will be good. At this point will cost me less to buy from another company. Buyers beware. Cause the company cant do nothing good for me so dont buy from them.

Gas control not working. I have replaced the thermostat twice in three years. Now, the hot water tank pilot will not light. The igniter works; a new thermostat has been properly installed, and the pilot will not light. The gas is on, and the tank has functioned. I just want a new gas control.

Our newly renovated condo came with a Whirlpool washer/dryer, and its been a nightmare. Not only has the unit destroyed 5-6 items of clothing, but weve had to have two repairmen out to remove socks that were sucked into the drainage pipe. On top of all of that, the customer service has been terrible - their hours are very limited, and theres nothing the call center employees can do beyond sending a tech out to look at your appliance for a cool $175. All this for a machine that was purchase new in June 2014! We will never buy a Whirlpool product again. Sad example of why American manufacturing has so thoroughly declined.

Let me just start by saying I have multiple Whirlpool appliances, and I have always bought Whirlpool appliances in the past. I bought a refrigerator 3 months ago, and it quit working. So, I called Whirlpool to come service it. The service repairman said someone left the freezer door open and it froze up. Two days later, I had to call them back again, because now, the fridge part was not keeping food cold. He came back out and told me it was the compressor. I then in return called Whirlpool that afternoon, and they refused to replace it saying they had to follow their Warranty Policy and they would call me back on Wednesday. They did call back on Wednesday and told me they had located the part. I got a call on Tuesday of the following week and was informed they could not locate the part. I called Whirlpool the next day, and they told me they would have to send it to their Exchange department for review and I would hear back from them in 3 business days. I asked for them to rush my request, but they told they have no way of doing that. I will never buy a Whirlpool product again!

I had the junky gas water heater for two years and cant keep the thing lit. Calling Whirlpool does no good. They give you the runaround; the store cant do anything. They know they have a faulty product and keep selling it. Some companies are only out for the money. If that wasnt the case, they would discontinue the junk. They will send you replacement parts but if you know nothing about them, you have to put out more money for someone to come and fix it. I would love to send them the bill! I would not recommend this brand of anything to anyone.

My Duet Sport washer drum is damaged due to the poor quality of the bearings. I replaced the Whirlpool Duet Front Loader Washer Bearing & Seal Kit W10253866, W10253856 but because the bearings were damaged the drum is also damaged. When I opened the rear panel of the washer the bearings had literally come apart and bearings fell out. All of the floor and the oil/grease was everywhere. I replaced the bearings but it didnt matter because the drum is warped. Priced the drum and it is nearly $400.00 to replace the assembly. The cost of the drum assembly is about half the cost of a new washer. I will never buy another Whirlpool product again. Just a shame that the cost of a replacement drum is so high. What caused the bearings to just explode and damage the drum. What did I do to cause this? Absolutely nothing. I have since discovered that this is has happened to scores of people with this same washer.

What a disaster! Within one year we had to repair the stove twice, the dishwasher and the fridge! Almost three years later, we are experiencing problems with two burners and with the fridge! The company does not stand behind its products. Avoid them.

I bought my new Whirlpool Duet washer and dryer in November 2011. Washer was loud from day one, but I never owned a front loader and thought that is how it was. Then someone told me that meant the bearings were bad, so I called. While still under warranty, they did replace; and I had to wait 6 weeks. Then a few months later, it started leaking. I had the extended warranty, and A & E came out and told me the bearings failed again. And now, I get a check for $750. But the machine cost more than that. Do not buy any Whirlpool, Maytag, or Kenmore. They are all made by Whirlpool.

It never seems to clean the dishes and it runs for 3 1/2 hrs. It is suppose to have all these Features but does a very bad cleaning job. I have used liquid soap, the cascade pods and the jet dry, still gives very poor results. Use to have a Kitchenaid that lasted almost 30 years - great appliance...

Washer is not worth the cost. After 4th year of use in a two person household the washer bearings are gone and require replacement. The washer sounds like an airplane. I was told based on my description of the issue that the water has leaked due to washing and spinning into the bearing assembly and has caused it to have friction. The Whirlpool warranty is just as costly as the machine.

I purchased a Whirlpool 50 gallon gas hot water heater 3 years ago. I have 3 daughters all in school age. When my old one finally quit due to tank failure and out of warranty, I went to Lowes and bought a 6 year warranty hot water heater costing around $600. Now I figured you get what you pay for RIGHT! WRONG! So about 2 years ago the pilot light started to just go out on occasion, a bit of an inconvenience but there was no default code warning me of any other issues. So typically we just relight it. I called Whirlpool to get help with this issue, but they wanted me to pay for a technician to diagnose the problem. Um isnt that what the warranty is for? I said dont bother. Im not paying $150 for someone to tell me what I already know. Ill just keep relighting it myself. So finally the pilot light goes out for the 100th time but this time I go to reignite it and BOOM! It sounded like a twelve gauge shot gun going off in my face! Then it flutters flames into the chimney of the hot water heater. Scared the crap out of me at first. But it finally stopped and run fine. Well Im laying in bed a few nights later and woke up to a loud thumping noise, I go down stairs and it stops. The following day Im in the kitchen and THUMP THUMP THUMP BURP BURP BURP. Run over to the hot water heater closet and theres the flames shooting out of the gas valve into the hot water heater then BOOM! Its out! The valve unit finally took a crap I guess. I call Whirlpool again to get my warranty - this time it definitely needs to be replaced. So the guy tells me the parts are covered in the warranty but a technician needs to look at it first and the technician Ill have to pay.. Excuse me but what the ** did you just say? I have to pay for a technician to look at your failing part? No I dont think so! Just send me the part - Ill replace it myself. Im a millwright electrician by trade. I specialize in power plants and refineries. Im sure this little gas valve wont be a problem. I spoke with these idiots on a Friday and he said I could have it ground shipped for free and it should be here in 5-6 days or pay extra for quicker delivery. What the hell did he just say? I could pay extra for quicker delivery on Whirlpools faulty part? ** whirlpool should be saying Well have the part overnight to you.Now since it was a 3 day weekend theres no sense in me paying $40 to have it delivered 3 day because it still wouldnt arrive until close to the five day. So I just looked to see where my damn part is because it shouldve been here by now according to the guy on the phone. NOPE! Its set to be delivered in 5 more ** days. DONT BUY A WHIRLPOOL PRODUCT. THEY DO NOT PRACTICE ETHICS.

Have always loved Whirlpool. Like the silverware in the door. Doesnt take up space for other dishes. Cleans well and quiet. Trusted brand and would highly recommend Whirlpool. All of my appliances are Whirlpool, stove, refrigerator, washer and dryer. You might call me a diehard fan.

I purchased a Whirlpool French door fridge 6 years ago. In less than a year, it was not cooling and I was able to retroactively purchase an extended warranty which ended up saving me a ton. Less than 3 years later it had broken 3 times with three different part problems with a total down time of 6 months. Despite saying it didn’t qualify for lemon law, I was able to get it replaced after presenting all the facts. 3 years later, the new one is now currently experiencing the same problem and running a toasty 58 degrees and my food is once again in coolers on ice. Shopping for a different brand and I recommend you do as well. Whirlpool used to be a brand you could rely on. No more.

My stainless steel french door refrigerators compressor quit working and needed replaced after 3 years and 10 months. I had to buy a replacement kit and it cost 400.00. The repairman cost 175.00. I tried to buy an extended warranty but they do not sell them. You get a 1 year warranty. The repairman told me you will be very lucky if you get 4 years out of the replacement. He said all of the new compressors are really junk. Remember when refrigerators used to last 30 to 40 years. Not anymore. It is a money racket. Do not buy anything Energy Star, it is all junk. I have gone through 5 washing machines in 18 years, and I live here by myself.

Purchased the refrigerator in May 2018 from Lowes. August of 2019 the compressor stopped working and I lost all of my food. Repairman came out and stated that the compressor was bad on a brand new refrigerator. I am now waiting for a new compressor to arrive.

Two years ago, we bought a Whirlpool gas range, model WFG361LVQ2. The range-top grates were porcelain-coated, smooth and shiny. The range itself has worked flawlessly (Admittedly, it gets only light use in our elderly household, which consists of me and my wife). The only complaint I have is that the porcelain on the grates is failing. On one of the grates, its flaking off where the flame contacts with it during cooking (Photos attached). On another two, the porcelain has developed a surface roughness thats clearly a prelude to same type of damage as the first. The fourth grate still appears to be intact. The differences in damage is no doubt due to the different amount of use that each receives.When I called Whirlpool, a supervisor there told me that grates have no specific life expectancy, and that is true for plain metal grates as well has porcelain-coated grates. She also said that some chemicals can penetrate the porcelain and shorten its life. I told her we didnt use any chemicals on the grates, but only rarely used common kitchen scouring powder, and I cant imagine the powder or the chlorine in the powder could do that kind of damage.When I asked what it would cost to replace the four grates, she said $187. I told her the entire stove cost about $500, and it didnt make sense to pay almost $200 to buy grates every two years for the next thirty years. I told her that the grates on our previous (non-Whirlpool) range lasted the life of the range - about forty years. So I declined to purchase new grates, despite her offer of a one-time discount of 25%. Though the grates are becoming eyesores, theyre still perfectly usable. So Ill hang onto them until I can find some bare metal ones to replace them.

No matter what I do after I wash clothes on quick or deep water cycle or even running the cycle over again, the clothes are left with soap residue. This is very annoying, particularly on dark clothing because it stands out. If I could start over, I would purchase a washer with an agitator. I watch the clothes as it goes through a cycle and the clothes stay in the same position...no wonder they dont get clean. What a ripoff!!