I purchased this Whirlpool WTW7800XW2 washer expecting it to last many years. As a senior citizen, I spent well over $700 on this model because of its large capacity and water saving feature. It has been in service for just over two years and has had limited use. Last week the glass top popped up and I notice that it broke at the hinge. This is definitely a design flaw. The washer has a lock feature and with the broken top, it is useless. I called Whirlpool and the customer service rep said she could sell me a new $250.00 lid at a 25% discount. Looking online, I found that hundreds of consumers have this same problem. Whirlpool refuses to acknowledge the defect. The customer service rep indicated that I should have bought an extended warranty. This is my last Whirlpool appliance ever!

Cabrio washing machine - I have had the exact same problems as all of the above... lid locks occasionally ... after many frustrating tries. I am ready to pick up this stupid washing machine and pitch it in the junk pile! Soap on clothes so I have to redo ... except many times it takes forever to get the stupid machine to restart... Most times I end up rinsing things by hand in the sink. We are constantly itchy from soap residue. My clothes do not come out clean. Especially the towels. Clothes are not spun out as much as they should be... Have been doing it over again by hand many times... which is not good because They still have way too much water in them and it takes 2 -3 Times longer to dry them! I am so disappointed in this set. I always thought Whirlpool was a great brand but, sadly, I was terribly mistaken. Never again. Finally got someone to say they have to replace all the controls. They say they will send parts but I have to pay someone to change it out... sounds like they admit there is a problem but will not accept full responsibility for it. I did not make the item so why do I have to pay to have it fixed? I believe they should issue a recall and make all of us believers in them again. I guess its my fault for buying their product? So... doesnt clean, spin, rinse, lock and has a bad odor... not a great product, is it?

We bought a Whirlpool Cabrio 2 years ago and they are an absolute piece of junk!!! There is only 2 people in our family so its not like we are washing big loads. It doesnt get my clothes clean and the clothes stink. I have followed the directions on cleaning the washer and it does not good. Now my clothes are soaking wet at the end of the cycle so I have to put it on drain and spin just to get most (not all) the water out of them. And when I take my clothes out, they are just as dirty as when I put them in. Called a technician and its going to cost over $400.00 to fix. This is nothing short of robbery!!!! This machine is a piece of junk. I read over 500 reviews on this washer and they all had problems that cost as almost as much as the washer cost to repair. There really needs to be a recall or a class action lawsuit against Whirlpool.

I like the double bottom french drawers but I don’t like that the top door hinge covers are plastic. Also I wish there was more height inside the refrigerator for tall bottles and pots. The wheels are great for moving.

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

I own a Cabrio Whirlpool washer. It already had several repairs and never got my wash clean. I complained to the company, no results. This washer is not even a year old. Why will they not stand behind their products?

Does the CEO know you do not stand behind your products? My washer is not even a year old and cost about $400.00. And you have stuck about $1800.00 into repairs instead of replacing a lemon washer! The washer had problems the 2nd month I owned it and you stuck a new clutch in out. Now just about everything replaced, it still does not work so I will order more parts. This is ridiculous. I would love to hear back from your CEO and would like to be reimbursed for 5 days of pay to take off and wait for repair men, laundry mat fees, etc!

We purchased the gas slide in range with gas oven. Immediately the temperature would hold a consistent heat, therefore it continually reset with a start sound (swoosh) every 5 minutes. The manual says it will do this, but clearly this is not normal. Then, the oven stopped working, showing an error message FBE0, that the cooling fan is not at high enough speeds! It sounds as though, along with hundreds of other people, we have all been ripped off! If anyone can please tell me what can be done about these defective stoves, I would appreciate it, thanks very much!

We purchased this Gold Series Whirlpool Dishwasher about 4 years ago. It worked very well up until April of this year. At that time, the main pump stopped working and it has to be replaced. There are just two of us in the household so the dishwasher was only used 2 or 3 times a week. We also kept it very clean with no build up. The gasket around the soap dispenser came out and one of the wheels fell off of the bottom rack. We just feel that 3 1/2 years is too soon for a major appliance to stop working and fall apart, especially given the light usage.

This machine was my dream machine for about two years. Then the noise started during the spin cycle. It gradually got louder and louder, until it got so loud that it sounded like a jet engine taking off. You could not be near the wash room and hear each other talk. Then it began to aggravate me with the UL flashing. I know how to load a washing machine. It was just a defect. Then it started making a grinding sound to add to the roaring spin noise. We were told that it would take over $500.00 to fix, so we just sat back and waited for it to die. Well, the other day it began to leak some water out of the bottom of the machine. Now today we are paying our last respects to a piece of junk that Whirlpool calls a washing machine! It is less than 5 years old. This was a $900.00 washer. There should be a recall. We should ban together and demand a recall! Now I will be forced to go buy a new washer. I can tell you which name brand I will not buy, Whirlpool!

I purchased a Whirlpool Washer at Lowes on 02/29/16. After 3 weeks it simply stopped after the last rinse, never drained the water or starting the spin circle. One and a half month later after 5 service calls still no working washer. Whirlpool customer service just adds insult to injury. They refuse to replace to washer or to issue a refund. Apparently they dont care if their customers have to use a laundromat indefinitely after buying one of their washers.

Machine wont go through the whole wash cycle., Wash, Rinse, Spin. It stops and shows an error message and then I have to keep rearranging contents, over and over. This is worse if you try to wash a small load.

I have a Whirlpool double oven. When I attempted to use the self-clean feature according to manufacture instruction, the bottom oven stopped cleaning in the middle of the cycle. I had a repairman out and he replaced the thermal fuse in the back of the oven. It cost $85. I didnt attempt to clean it again for another few months since I dont use the bottom oven often. When I did attempt to use the self-clean feature according to manufacture instruction, the same thing happened. I called the repairman and he said that the thermal fuse would blow every time I tried to clean the oven, because of the way the oven was manufactured. I contacted Whirlpool and they were not at all helpful. I intend to contact them again.

I have owned a Whirlpool Gold refrigerator since 2011. It has required two repair calls due to a water leak. The company did repair it free of charge on the second visit even though it was out of warranty. It is now leaking again which has caused damage to my wood floor and basement ceiling tiles. I am told that I have pay for the repairs this time even though it is the same problem. I was offered a modest discount to purchase a new refrigerator. I will never buy another Whirlpool product. This refrigerator should be recalled. I recommend GE products. They stand behind their products and they last a lot longer. Shame on Whirlpool! So many complaints with very little response .

Bought Whirlpool 30 gal propane water heater in Feb, it lasted until May before the unit died. Paid for the extended plan warranty (NEVER do that!). Called support and they said they could send someone out in a little over a week (week with no hot water). The week goes by and on the day it was suppose to be repaired the guy calls and says his van broke down (this was a Friday, getting that early weekend). The earliest they can reschedule is in another week (over 2 weeks no hot water). Called Lowes to see if I can just return it (extended plan and all), no, you need a return code from the whirlpool customer support. Call the Whirlpool number again to ask for a return code, no, it is a repairable problem (even though no one will come repair it). Lesson learned, will never buy Whirlpool or anything over $50 from Lowes again.

I bought a whirlpool water heater at Lowes 4 months ago, and it has stopped working. I called the customer service number and was treated so unjust. I told them that I had just had it looked at by a plumber and he said that the water heater needed to be replaced, I told the whirlpool represented if what the plumber had just advise me. So I asked them if they could just replace it, the customer service representative told me I had to call another number to have their service people look at it and that wasnt for another 10 days. At which time I asked the representative what was I to do without hot water for 10 days. She told me that they could only schedule it that way. So Im here to tell you all please please please dont ever Buy anything from whirlpool because they will not back it up! I on the other hand just lost $500 and went out and bought a Rheem water heater instead.

I purchased this machine in April and already, the right leg is rusted and the under seam of machine is rusted. I have throw rug under it and where the leg is, there is rust on the rug. I called service from Whirlpool and 2 servicemen came out. The first one told me I was loading it wrong and the water was splashing over the inside tub to rust the leg and I asked, So why is the seam under the machine rusted? No answer. The second one came out and told me he could not find anything wrong with the machine and doesnt know why it is rusting, but he never gave me a paper to sign off on. He also said that maybe it was rusted when it was delivered. Not!!! Then I call P.C. Richard in Watchung, NJ where I bought the machine at and told them about the problem. They sent a serviceman out and he said that the bleach condensation is causing the rust, its known fact that this machine has this problem. He said that the water does not run through the dispenser but there is a model that does. I want a credit on this machine and get the upgraded one. It states on the machine that I can use bleach but it doesnt say it will cause rusting. I want you to tell me how a 9-month-old machine is rusted on one leg and the seam underneath is also rusted!!!! I had a machine for 10 years and it wasnt rusted. I am very unhappy with this product and with the customer service of Whirlpool. This is my first Whirlpool washer and I would not recommend this washer to anyone. I paid $600.00 for this washer and it should not be rusting.

We purchased a Whirlpool washer/dryer set 19 months ago and the washer just stopped working. Our trusted fix-it man came out and diagnosed it as a spin bearing problem assuring me it was not anything we had done. He stated it was a defected part or Whirlpool had never put grease in the bearings. A 450.00 part not counting diagnosis and labor. When I called Whirlpool, the first response I got was that they were sorry but we didnt buy the extended warranty, and of course the warranty it had was only a year. I asked to talked to a supervisor and finally she agreed to supply the part, but I was still responsible for the diagnostic and labor fee, which will be a couple of hundreds of dollars! Not happy with Whirlpool and will NEVER buy any product with their name again. Beware consumers!!!

Right from the start of buying a new suite of Whirlpool appliances, the light over the range burnt out. We figured it was just a bad bulb so we replaced it. Soon it burnt out again, replaced it again, then again it burnt out. I finally called Whirlpool about the problem and found out it is the electronic panel that needs to be replaced... Of course at a full charge to me! I am so over WhirlPoo, (yes I spelled it that way on purpose) every single appliance has had issues. I have just lived without a light over my range because fixing it is more expensive than buying a whole new microwave. Never again will I buy any WhirlPoo appliance!

We bought this Cabrio washer WTW6400SW2 several years ago. Immediately after having it delivered and installed, it started displaying an F1 fault code. The main control board was replaced under warranty. It happened again within six months. Another board was replaced. That board lasted another six months. The warranty was up by then, so I used the machine by hovering over it and restarting it every time it failed. After two years of this piece of junk, we put it in storage while we worked on the road. It was brought out on 10/01/11. I called a repairman (who came on 10/04/11) to come replace the board again. He told me that the last two times it had been replaced with the same defective board, that Whirlpool had never fixed the problem. He claimed he had the new improved board, which he replaced for about $350. Two days ago (361 days later), it went bad again. The same repair company came back and said it was the board again. I just tried chatting with a person working on the Whirlpool website. They (of course) said they would do nothing about the washer. They do not stand behind their product, obviously. Does anyone know of a class action lawsuit over these washers? It is a ridiculous amount of money to spend for a product that does not work. This is just wrong!

I’ve had my washer and dryer for a long time and it has been okay and it’s time to update. It has had its up and down and I may get another just after a while they are outdated and better appliances come along. Smarter people are making smarter things.

The refrigerator fits perfect in my space, keeps frozen (ice cream is creamy not a frozen block ) and cooled foods well. I love the glass shelves. I purchased 2 more bins for the refrigerator door, now I can get all my spices and condiments on the door as well as lots of other things. The freezer has racks instead of glass shelves. The top shelf is adjustable, that is nice in order to use more space. I love the ice and water on the outside of the door.

Nice looking, prices very fair for quality product. Options are always good. My mom used Whirlpool. That thing that goes in the middle of the old time washer is now gone. That thing would rip or stretch out clothing bras. Anything that was nice it would make it look horrible. Ive had my washer and dryer for 6 years and they still work like new. When shopping for a washer and dryer I do look for capacity, energy efficient and the brand. I prefer to stick to the old school brands just like my mother did. I must admit that I do love the fact that it is an HD high efficiency washer. The deal-breaker would be a low quality construction made a washer or dryer nobody needs to have problems with it. If youre spending that type of money you need to get good quality items.I love my washer and dryer. Theyre both and white color. Its a Whirlpool Cabrio with HD High efficient load energy saver and H2 wash system. The washer has a lid with a see-through glass which I love. My dryer is also a Whirlpool Cabrio steam with a resource saver that gives me a lot of different options as far as my clothing is concerned on how I need it dry.

Whirlpool hot water heater - The water coming from the faucets when it is hot is red. Therefore, I contacted Whirlpool and was informed that the anode has failed. The anode is not covered because, according to this company, it is not considered a working part. It baffles me that the anode is not a working part since it keeps the tank from rotting. I have only had the hot water tank for three years and this part has failed causing my hot water to be red. Since this company contradicts itself, I either have to live with red hot water (rust) or replace the part on my own. Unlike your company, Lowes has customer service. They apologized and will be paying for half of the expense for the part. Unfortunately, I still must pay for an employee to replace the part. This whole situation is absolutely ridiculous. I will never be purchasing another item from your company and in addition to that, I will tell everyone I know to avoid this company at all costs. You should strongly consider revising this policy before you lose all of your customers.

We purchased our refrigerator about five years ago and we have dealt with it freezing up constantly. The coals and vent are at the bottom of the refrigerator. I believe that is a lot of the problem. We have continuously blowed off the coals to keep it from freezing up but sometimes its still freezes up. I do not recommend the two-sided door Whirlpool refrigerator.

I bought my Whirlpool 50-gallon gas water heater from Lowe’s 10 years ago. After the first year, it was nothing but problem. The thermocouple was replaced so many times and there’s the inconvenience of not having hot water. Customer service sucks and they continue to send you to Lowe’s to pick up the part for free. I have 2 more years on the warranty and Im replacing it after its over! 3 days ago my water heater stopped working and now again I will replace the thermocouple. Dont buy Whirlpool products: they are junk!

Im glad to see that Im not the only one that is dissatisfied with Whirlpools products. Three weeks ago I found my basement to be flooded and you could tell that it was from the hot water heater that was installed in 2005. The plumber changed the release valve. I thought that was it. This past Wednesday I go down the basement and find another flood. The plumber said pilot was not lit. The explanation was wind could have come down the chimney and blew out the pilot. Pilot was relighted and within 12 hours there’s cold water again. I called the plumber again and said that the thermal coupling must have gone bad. I went to Lowe’s to get a replacement and found that Whirlpool is sending a free replacement but I would have to pay shipping. All well and good, but what do I do in the meantime for hot water? If Whirlpool made a mistake, why didnt they send the replacement parts to the businesses that sell their products? I guess that would be the simple solution; instead, they expect me to pay $30.00 for shipping and be without hot water. Well, let me tell you: Im tired of this hot water heater. Whirlpool can go out of business for all I care because they dont stand behind their products. Im going to buy myself a Rheem and Im sure Ill be a lot happier. Need a new hot water heater? Don’t get a Whirlpool!

I have the Whirlpool washing machine for last 15 years and there has not been any complaint since its acquisition. I do a lot of laundry because I have a big family, but not major issue so far. I will recommend this brand to anyone willing to buy a washing machine.

I purchased a new high-efficiency front load Duet HT Whirlpool washing machine (WFW9200SQ02) in January of 2008 for nearly $1000. I dealt with the mold issues and permeating smell for all these years, but the machine failed catastrophically this month - after just over 3 years - on a $1000 machine! The rear bearing went out. The parts alone are nearly $500 and the labor is estimated to take 3-4 hours by a trained technician. We are talking about an $800 repair --more than a new machine would cost. The most disconcerting part is to see how often this is happening. It is commonplace. The bearings go out on these things, sometimes after only a year or two, sometimes after 3 or 4; but it is very rare to have any machine go longer than 6-7 years. Whirlpool wont do anything. The best chance is forcing a recall related to the class action lawsuits pending about the mold issues, but by that time, how many people will still have their machines?

We purchased this refrigerator towards the end of 2008. The entire interior of the refrigerator is imploding. The plastic Whirlpool used to frame the glass shelves is cracking and shards are falling off. There are 3 drawers; one has already fallen because the plastic sliders the drawer moves along has disintegrated. We noticed the small hairline cracks appearing some time ago but never thought they would go to this extreme. Apparently the plastic used cannot stand up to cold temperatures.I contacted Whirlpools chat and was told that the product is out of warranty and I need to place a service call to get new parts. I proceeded to email the CEO of Whirlpool, Mr. Fettig because I dont believe I should have to pay for a service call when its a manufacturing problem. I received a call the day after and was told the same thing; that they are sorry we are experiencing a problem but the warranty only covers the first year. I was told that if there was a problem with the plastic being inferior that they should have cracked in the first year. I responded that the cracks may have been occurring early on in the back of the refrigerator which is the coldest part but were noticeable.Its very frustrating because a refrigerator purchase is expensive and not something that I planned on doing a mere 5 years later. I believe that Whirlpool at the very least could have shown goodwill towards their customers and given at least some discount on the replacement parts or at the very least a certificate with an amount off toward the purchase of a new refrigerator. Its a win-win situation for everyone because the customer is still happy with their Whirlpool refrigerator and/or it guarantees repeat business for Whirlpool. Apparently Whirlpool doesnt care about keeping customers happy and want and/or need repeat business. Its the last Whirlpool I will ever purchase!!!

I purchased my range, model #WEG730H0DW0 in April 2016. I am extremely dissatisfied with the product and the Whirlpool service. I guess its comforting to know that Im not alone. Ive had two problems so far. The first is with the broiler that clicks on and off. It took several visits and a new electrical board for the service person and me to figure out that the door has to be closed to broil. Not sure about all of you but I am used to keeping the door cracked open to be able to keep an eye on the food being broiled. Apparently there is a thermostat at the front of the oven designed to keep the electrical controls from getting overheated or from melting so when the door is cracked open the heat from the broiler hits that thermostat and the broiler is shut off.The people at Whirlpool are awful and rude. I made so many calls and described the problem in so many ways and not one person knew about this newly placed thermostat or thought to ask about keeping the door closed. It took me and my service tech over an hour of troubleshooting on his SECOND visit to figure it out. He looked up the specs and we figured it out. I wonder how many new electrical boards have been replaced when the solution is as simple as keeping the door closed. A stupid design. Also having the same problems with the knobs. They turn so easily that twice I have smelled gas and realized one of the knobs was turned ever so slightly (before the clicking sound to ignite the stove).Then the third time could have been deadly. I had friends come pick me up and we stood in the kitchen for a bit before we left for the entire day. When we returned the whole house smelled of gas. Someone inadvertently must have brushed up against the stove and the knob turned. My dog, thankfully is still alive and so are we. THIS IS NOT ONLY A STUPID DESIGN BUT A POTENTIALLY DEADLY ONE!! I am forwarding this message directly to Whirlpool in the hopes of getting my money back. I am replacing the range immediately and will never purchase a Whirlpool product again!

I hope this review makes it to the president of Whirlpool! My husband and I built our first home and finally moved into it on April 22, 2017. We saved everywhere we could and I did my best to research my appliances. I was so excited to buy a BIG refrigerator for our family of five, (3 are hungry teenagers!) after years of using a smaller side-by-side. We went with the 31.5-cu ft French door/drawer with dual icemakers, model #WRF993FIFM. The original price was $3,599 but we got it on sale for $2,298 at Home Depot. After only 5 months it stopped cooling! I woke up one morning to find a fridge full of spoiled food!! After waiting 3 weeks I had 2 different repairmen come out and have been told that it is un-repairable due to two parts that are needed, one of which is on back order indefinitely. Ive called Whirlpool numerous times and only get the run around and Im sorry mam we cant do anything else. So Im just supposed to be without my refrigerator until who knows when?! The first 2 weeks of this crap we had to live out of Igloo coolers on our back porch. That meant no buying real groceries, only milk and juice and drinks. Thankfully the awesome people at Home Depot brought us a loaner, which is an apartment size fridge, to use while we wait. So now I just have to walk across the house to my garage every time I need something, and I cant buy much food because it wont fit!! Im so disgusted with how Whirlpool is handling this!!! Not only did we buy our fridge but we also went with Whirlpool for our stove, dishwasher and microwave, and we already owned a newer Whirlpool washer and dryer set. We spent thousands of dollars and cant even get them to exchange this piece of junk! Come on Whirlpool, surely you dont treat all your customers this way!? Do the right thing and let us have a replacement!!!

We purchased the Cabrio Agi top loading washing machine in 2011 (3 years ago). After 2 years it started leaking from the plastic drum (Bearings?). Luckily we have it in the basement on concrete floor, so there was no damage, just frustration. This was poor purchase on our part. We should have searched for more reviews. The wash time is ridiculous; it is too long, an average of 50 minutes per load. I dont know about how clean the clothes were, I guess they were OK. I didnt notice a smell, or them looking dingy. The Cabrio is a piece of junk if the bearings went out after 2 years?? We just purchased a heavy duty Speed Queen, top loading, agitator washer. My wife loves this, its like the old Maytag we had. They told us they wont be selling these washers after next year. Buy them while you can. The Cabrio is headed to scrap yard.

This washer never worked right. It simply mixes the clothes up with little water. A real piece of crap. See the 2000 other complaints. Time for class action suit.

These machines are designed to clean your clothes by rubbing them together which they attempt to do in a minute amount of water. They destroy the fabric, pull the seam out of shape, wrinkle them beyond the point of wearable, do not get them clean and do not get all the detergent out. I have had clothes come out partially dry. They also do not dilute the fabric softener, leaving unremovable stains on your clothes. In addition, they take forever to do a load of clothes even without the extra rinse you need if you want any hope of getting the clothes rinsed. The dryer is the slowest dryer I have ever had. The steam refresh that is supposed to get the hideous wrinkles out of your clothes does not put steam into the dryer. Instead, it sets the dryer to the highest heat so that those clothes you did not want on high heat are now getting it; then it shoots bursts, yes large bursts, of water on them. Your clothes come out a combination of still wrinkles and wet. If you hear of a class action suit, please contact me. These machines should be recalled.

This microwave usually has great reviews but I think I just got a dud. I purchased this model (WMH53520CS-0) as part of my new home build. After 9 months the door sensor broke and anytime we would go to run the microwave, it would tell you to open/close the door. Whirlpool sent out a certified factory dealer to fix the problem. They found it to be a faulty control panel and replaced it. After that was replaced, the exhaust fan broke. Whirlpool sent out that dealer again with the new part, and everything was working perfectly. Flash forward a whole 24 hours later, and the microwave would make the loudest sound ever and shut off after 3 seconds and blow the fuse. Turns out the turntable motor had broke and the NEW control panel was already faulty.The turntable motor part was on back order for a month and I am still currently waiting for it to be shipped to me while I have a microwave shut off collecting dust. As most anyone would be, I was extremely frustrated knowing that Whirlpool has spent at least 4 times more sending out certified dealers and replacing parts, than if they were to just order me a new microwave. They stood firm on their policy even if it meant a customer without a working microwave for over a month. Whirlpool did offer me a nice $75 debit card that took 4 weeks to arrive to help pay for a temporary microwave, but they would not work with me when I asked for the warranty to be extended 3 or 6 months. I wanted that peace of mind and its frustrating that for 2 of my 12 month warranty, the microwave was completely broken.Overall, its a nice microwave when its working but with all I have had to go through, I wouldnt recommend this model nor any Whirlpool appliances...

I purchased my Cabrio Whirlpool washer 4 years ago and have had problems every since I bought it! Thank goodness I bought the extended warranty! The last two repair bills were over $1000 each! My warranty just ran out and I had it repaired last two months ago! This is not my first complaint! When will they start listening to consumers? This is ridiculous! Now I am faced with the problem of just trashing this washer or spending another $1000 to repair it! Something needs to be done! I am warning all of my friends and family and will post again my problems with this washer on all my social networking sights! Whirlpool needs to take responsibility for their problems! I will never purchase any Whirlpool products ever again if they do not assume responsibility!

We purchased a new Whirlpool in June 2017. About 3 months ago it began making foul tasting ice cubes and now they are so bad we cannot use them. Called Whirlpool for help solving the problem and they basically told me there was no fix. It was my bad water. My water is wonderfully pure and good tasting. It only is bad from the ice in, what I consider a new fridge. They did want to make an appointment for a tech to come out and check it. I dont know why when they told me it cannot be fixed. So sorry we bought a Whirlpool and will never buy any of their products again. Hopefully this will help someone else.

My husband and I bought a new Whirlpool Cabrio Platinum Series Washer and Dryer in November 2012 from Lowes. My clothes, especially towels, smell like mildew and mold since I have used it. I thought it was just me. I have even thrown some items away when they smelled so bad. I love doing laundry but this not being able to have clean smells was driving me crazy. I tried everything I could think of but to no avail. Finally in October of this year 2015 my washing machine began to make a loud noise. My husband said sounds like a bearing is going out. I immediately sought a repairman thinking that it would be a simple fix. $420 later I had a new bushing, bearing, sleeve, etc. The machine was still making noises even louder and my repairman came back, this time to the tune of $180. So far weve spent $600 on a washer that we gave a little over $800 for. Now I have a UL code showing up when my load is almost completely done and guess what? My repairman says he has yet another part that should take care of the noise but he wasnt so sure about the panel. He may have to do a little research on that. I think all I have is a repairman that is a parts replacer so we were forced to purchase a new washer yesterday and my Cabrio is sitting in my garage. If someone needs a boat anchor just please contact us. I wrote a letter to the corporate office of Whirlpool before I even knew that so many consumers were having problems. Two repairmen told me that the Cabrios were junk. Most of them belonged in the landfill. Whirlpool customer service called me and offered me a discount coupon on a new washer. I told them that I didnt think I needed another piece of crap. I also questioned them as to why they could foist these crappy machines off on the American public. They had no apologies whatsoever. While researching what brand washing machine to invest in, I realized that there were numerous complaints regarding the Whirlpool Cabrio. With as many consumers who have been taken advantage of with this awful product, why cant someone do something?

We have the four-door model, french fridge part, drawer, and bottom freezer. Overall has been a good appliance. Icemaker burned out in third year. Icemaker replacement is very noisy, popping and groaning during drop-out and refill. Noise level otherwise is average.

I purchased a Whirlpool electric water heater in August of 2008. The unit had a 12-year warranty on the tank. On January 21, 2012, I discovered that the water heater sprung a leak somewhere in the tank shell; it’s not the pressure relief valve, thermostat or anode port. The tank was never abused and operated well within its design limits. Not sure what caused it to start leaking into the catch pan and out onto my laundry room floor.I purchased the tank at Lowes and went for the longest tank warranty to reduce replacement intervals. I sent Whirlpool an email on 1/22/2012 explaining my problem and I referenced this site. The next day 1/23/2012 I receive a call from Whirlpool (Chris) asking me about my problem. I explained again and they gave me an RMA number and told me to go to Lowe’s and they would replace my hot water heater. I went straight to Lowe’s customer service and within an hour I was on my way home with a brand new hot water heater. Thank you, Chris, Whirlpool and Lowe’s. I am very happy with my outcome on this issue.

Mine is a stacked unit...saves space and I just love the stooping over factor... BUT, its an energy saver and I always have to add about 5 gallons of water to it for it to cover even half a normal load...ugh!!!

We bought model WRS571CID*** which has an in-door ice maker that has stopped working after exactly 3 years. An excellent authorized service rep advised that the wire harness from the freezer to the door was damaged by chafing from normal opening and closing the freezer door, which has caused the ice maker wires to break, thereby disabling the ice maker. The only remedy is replacing entire the door, which would cost $1700 according to Whirlpools published repair data, which he is obligated to charge. Apparently, the wiring harness is not a replaceable part, because I suspect the labor hours needed to disassemble and reassemble the door is prohibitive. Well, a new fridge costs about the repair. I spoke to the Whirlpool company about whether they acknowledge that the design is faulty and that the door should be replaced at their expense even out of warranty, and they declined.So I advise prospective buyers to be aware of this issue and watch other reviews. There are many customer reviews on various sites complaining about this very issue. Our workaround is to put ice trays into the freezer to make ice, and while the dispenser still works, pour the ice thus made into the ice dispenser manually - until the wire control that also becomes damaged and stops working. I would not recommend buying this model.

Whirlpool - good price for pair. I have had this pair for over 10 years and they work good and are reliable even though they were not the top of the line models. Large capacity is a must - energy efficient is also a must. Discounts are nice to get but if not available I will go with a name brand. I want a washer with an agitator not one of the new ones that dont have one. Reliability is the most important factor so repairs are not needed. I want a full size washer with several cycles and all cycles have a cold rinse to save energy. Having a center agitator is a must - cant stand the newer ones.

Purchased 11-02-2016. This Whirlpool/Kenmore dishwasher is falling apart. Top rack wheels are totally broken, ordered parts 4 times, gave up. Now they are held together by gorilla glue. I have gone through 3 gray plastic end caps for the top rack runners. Now one is contained by a plastic slip tie. Last week it started leaking. Sears was totally useless. Whirlpool keeps sending me back to them. Now, I have to go buy another new dishwasher. It will not be a Whirlpool. Next time getting the extended warranty.

Love the bottom freezer & french doors. Unit uses way less energy than older fridge. Did need a new evaporator but it was covered by a recall. Happy so far. Love having icemaker in the door so it doesnt take up freezer space.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

I purchased Whirlpool Cabrio on 04/06/2017 at Best Buy in Lake Worth. The washer stopped working last month. I went to Best Buy to complain. I was told to contact Whirlpool which l did. Was on the phone for over 2 hours with representatives. Finally l was told a service person will come take a look and tell me whats wrong with it. The service person came after one week out. Told me he has to order parts and it will take a week for the parts to come in. That his company may send some else to come and fit the washer. Meanwhile l took off the day from work.Now today 08/08/2017 the service company that Whirlpool contract with sent another service person with the parts only for him not to be able to repair the washer. He has to order more parts and it will take another week or so. I was so upset called Whirlpool, spoke with two different representatives. All they could say is sorry for the inconvenience that l have to wait until the service person comes out again with the parts. And if he cant fit thats when they will be able tell me if it will be replace. Bottom line is that l will never ever buy Whirlpool products again.

Just plain terrible. Purchased Whirlpool Gold Seris Dishwasher Model w10698637a in June and now its been 3 attempts so far to fix a brand new dishwasher that does not clean. So far I have been asked... have you been heating the water before you start the cycle?, my favorite... Is this a whirlpool dishwasher. So I find out today that it will take another visit from a company that hasnt been able to fix it, plus a call to the tech line to make sure they havent missed anything. Heres what Ive missed, a dishwasher that cleans.

I purchased a Whirlpool washer and dryer from Best Buy. I purchased one on sale that was a great value. The delivery and set-up went well. However, the model I have had a loud vibrate. The drum in the washing machine would wobble and shake across the floor. I finally had to return it and replaced with same model. I experienced the same issue after 30 days. I didnt take the insurance out and I regret that move.

This has been the worst purchase I have ever made! Within 2 months of it going out of its one year warranty I called (Lowes) to have it repaired. Spent $300 on the first repair to get rid of the jet engine sound AND the oil splatter all over the floor then within one month from that repair it has a F code error and wont finish washing a load. It just stops. I have tried everything from unplugging it to restarting and it just wont work. Now have to wait 1 week for the repairman to come back out (hopefully that warranty of 90 days will be helpful). Do Not Buy this machine!!!

Two years ago, I bought two Whirlpool Water Heaters. Like the others who have posted, after one year the first one went out. Last night the second one went out. I just wish that I had read the prior reviews before I bought these replacement water heaters. I also had to navigate a very unfriendly customer experience, first with Whirlpool and then the manufacturer. After that I had to wait a week to get a repair person out only to have to order the part and then be asked to pay for it and the express shipping. Totally amazing! I have decided to buy new water heaters next quarter because I just cannot put up with either the aggravation or the expense of constant repairs. I will returning these two water heaters to Lowes, where they were purchased. Perhaps if enough of us return them, Lowes will decide its not worth damaging their brand to sell a known inferior product. When this many people complain about a product and they all have the same experience its a lack of quality, plain and simple. And I would think that Lowes would not want to go on supporting a known inferior product when even Whirlpool is lukewarm in their response to our complaints.

Ours is a glass top & has 2 dual burners & we are very pleased with that feature. The oven however takes quite long to preheat & the alert sounds are so weak you can barely hear them. It was a rapid purchase on a sale item. I wish we had shopped a bit more.

My stove fits my needs as I’m looking to simplify my life and not have a behemoth with books and crannies to scrub and clean or polish. I’m looking to cook less, not more and this stove fits the bill just fine.

My Whirlpool refrigerator model #ED5FHEXV001, serial #HR0248 - I have spoken to a couple of reps on the phone. I am very dissatisfied because it was like one rep I spoke with on the telephone advised me to buy an extended warranty and at that time, the company would consider alternative ways to deal with this complaint and perhaps replace the refrigerator. I did not want to pay an additional $100 for a warranty, unless the company would guarantee me a solution, preferably my money back. I did not really believe the warranty would help me after the warranty was expired. I would still have the same problem and I feel that in the event after the extra warranty expired, the company would tell me I should have kept the coils clean, which is my complaint. There is no way to keep the coils clean. I guess blowing out the residue, then all that residue material would end up all in my house. Also, very important, there have been 3-4 technicians to my house the first year. I was told various things to do, such as adjust the refrigerator to a lower setting and freezer to a little higher setting. One tech actually replaced a part? The second tech said he would clean the coils. The last tech told me the problem was my coils had to stay clean. My question is, how the heck is that possible with the coils on the bottom of the fridge and susceptible to a lot of dust and dirt, unless I move my fridge everyday? Most people do not expect to have to clean under the fridge each day and the coils would still be dirty anyway. It is very dumb that the coils are not on the back of the fridge. With the fridge coils on the back, I have never experienced this problem. Please advise what my next step would be. Thank you.

Whirlpool Washing machine Model WTW4800XQ1 - This machine ran fine for the first 6 months, even though my old machine took 40 minutes for a large load and this one takes an hour. Then, I had to call the repairman out and he said it was the fill valve. He didnt have one on the truck and said he should get it in within 3-5 days. Well a month later, I had to call Lowes again to find out what the problem was. They had him back out with the part within 2 days. Then, I had to call again. This time the repairman ran a test and found a bad spin motor, he had the part on truck. Third time to call and the machine is back to not spinning out properly. My old machine lasted over 14 years. Whats wrong with these new ones?

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

Outstanding, however our location has a hard water rating and as such we have to use a deodorizer to balance this out. A wide range of variables which are a fit for my purposes. Interior dimensions and layout are more than perfect for my uses. This particular dishwasher is built in so blends aesthetically into the design of the kitchen seamlessly. The product has a drying system which successfully blows air over the top tray to eliminate wet areas within depressions of crockery, glass, and so forth, its excellent. There is also a light steam setting which removes tough deposits from surfaces.

The felt drum gasket came off our 6 month old Whirlpool Cabrio dryer purchased through KB homes. When I contacted the helpline on the 16th of May I was promptly set up with an appointment on the 18th of May. On the 18th I called to confirm a time and the company that whirlpool subcontracts in San Antonio, said they had no appointment for that day and the soonest they could get out here was June 1. I contacted Whirlpool to let them know this wasnt acceptable and I received many apologies and I understand how you feels. I asked how is it you have one company in all of San Antonio to service our dryer? Again more apologies. Then I asked since when does only apologizing and saying, I understand your feeling, be the end all of your customer service? No reply to that so I called Sears who promptly had a repairman out to the tune of $200 bucks with my military discount. Never again Whirlpool.

Ive had other brands of washers and dryers and I must say I always return to Whirlpool. They are well made and do what they are supposed to. Never had problems. My last set of Whirlpool was about 12 years old. Great product.

I had started the dishwasher and had gone to bed last night. I came downstairs ten minutes later to get a bottle of water. There was smoke throughout my downstairs levels. Our Whirlpool Gold Dishwashers control had dark, noxious smoke emitting from it. I tried to turn it off but it was too hot to touch. I went to the breaker box and shut it off there, turned on fans, and went back to bed. This morning, it turned the electricity back on. It started smoking again. I tried to cancel the cycle but it wouldnt cancel. I opened the door to stop the cycle and it continued spraying water and still wouldnt shut down. I had to shut it off at the breaker again. Next problem is my refrigerator, washer and dryer are all on the same breaker. UGH! This is the second Whirlpool I have had. The first one had a rusted tub that leaked into our basement. The repair guy said he had never seen that before...sure...why would you put something in a dishwasher that would rust out on you? Whirlpool, NEVER AGAIN. I WILL PASS THIS INFO ON TO EACH AND EVERY PERSON I EVER KNOW. COUNT ON IT.

I like the dishwasher. It cleans pretty well. Some time it soap doesnt open and the dishes don’t get cleaned. But when it’s working good the dishes get cleaned very well.

We have always bought whirlpool appliances, and trusted the name. We can put a man on the moon but we cant build a reliable bottom freezer refrigerator. My previous refrigerator was whirlpool. 19 yrs old when it went out for a new whirlpool bottom freezer fridge, 2014 Jan. 14 months after purchase, no warranty. The temp in freezer and upper compartment would increase and stop making ice. At first, we thought it was the icemaker. Repairman NOT FACTORY TRAINED, THIS IS VERY IMPORTANT.. Came and looked at it said, yep, icemaker. Plugged it in after 4 days. Just like brand new - making ice, not the icemaker. About 4 days later same problem - temp increasing. Called the store where we purchased it, sent the same repairman. He said it was a cooling fan. This went on for 2 months trying to figure the problem. Well, we cant rebuild a refrigerator out of parts it doesnt need, so we called a FACTORY TRAINED TECH who diagnosed the thermostat and defroster in the bottom of fridge taking two screws out and pulling bottom freezer out. It was iced up. Cost to fix it - 522.00. So I called whirlpool corp., explained problem. They agreed to pay for parts if we paid labor, 100.00. This is doable. However, if we continue to have problems after this, we will purchase a top freezer fridge, no ice maker because they constantly break down.

I bought in 2008 a Whirlpool Cabrio washer because it was the best. It cost me $900 plus 170 extended warranty for four years.This month, my washer showed an f1 code. I call the Maytag store and guess what, they are not there anymore. They closed the store. I called for my extended warranty and guess what, they are not with Maytag and they filed a chapter 7. So, I spent over $1000 in a machine that only worked three years and now I have to buy another just because no one wants to take the responsibility on the warranty. I have to pay another $300 to fix the problem and even doing that, theres no guarantee that it wont fail again. So, and this is to the people of Maytag and their cheats, you may take my money but you lose me as a customer forever. Thank you for nothing. I will keep that in mind next week when Ill be in the store buying another washer.

IM OLD AND DISABLED WOMAN. Bought a brand new $800 Whirlpool top loader washer and it wont work after not even a month. Called whirlpool and had the worst customer service from Tammy. I have to wait to compose myself to call back cause the washer is junk... F9E1 SENSOR. IM NOT A MAN! Worst customer service. Thought my washer would last longer. Its been 1 hour 45 minutes. Wont turn off. I CANT unplug TAMMY! IF I COULD I WOULD!

We purchased a Whirlpool Countertop Microwave (model MT4155) at HHGregg on 6/02/2012. (This was a replacement for another oven that failed after a couple of years - NOT a Whirlpool.) On 6/04/2013, i.e., 2 days past the standard 1 yr warranty expiration, the oven went nuts. I was cooking a plateful of baked potatoes on the auto setting. When the potatoes were done, I opened the door to take them out and the oven started to run! WITH the door open! When I shut the door, it stopped. So the only way to get the oven to operate was to OPEN the door. I dont think this is a safe or effective practice. Knowing it was two days past the warranty, I called customer service anyway just to see what they would say. To my surprise, they (I talked to two different people) were VERY pleasant and accommodating, and offered to cover the cost of repairs and even set up an appointment for the authorized repair person, and then called to verify the appt. as well. Great! I was impressed!The repairman showed up as scheduled and seemed puzzled at first, but he dismantled the outside cabinet and determined the fault was in the door switch. He wasnt sure he had a replacement with him, but he did find one, put the new part in the oven, and re-assembled everything. We made sure it worked and he then left. Fast forward 5.5 months, when again I was cooking potatoes (boiled this time. Maybe the oven doesnt like potatoes!). I had the timer set for 20 minutes on 100%. I was out of the room when it quit cooking, but I think it ran for about 6 minutes and then just shut off and could not be persuaded to restart. The clock continued to count down, and all the other bells and whistles still functioned - it just wouldnt cook. Major hassle. The following day, I was looking at it, messing around to see if I could figure out what was wrong, and discovered that if I pushed on the door latch just a little, the oven would run. Well, thats a nifty workaround, as long as you arent doing any more than briefly reheating something, but not so great if you are actually trying to cook something. I continued to do this for the next few days and then suddenly one night it reverted to the first bad behavior - only running when the door was open. I was able to get that to stop, but the following day, it refused to work at all and it is now sitting here uselessly, just a little over 1.5 years old. I want to go buy another oven (and YES - a different brand!) - my SO wants to repair this one, again. After reading the experiences of others on this site, I REALLY cant see the point in repairing esp not if I have to pay this time (which I probably will), and also when it seems to be a faulty part/design causing this problem. I dont have the time or patience to deal with an unreliable appliance, esp one that I use often. I have not tried to call customer service yet, but Im not expecting great things, not this time. Planned obsolescence? Sure makes me wonder.

I own a top two door refrigerator cabinet with a middle drawer meat cooler and a pull-out out lower chest freezer. The ice maker is built into the door and it is a very simple to operate and stable appliance. The refrigerators space is very functional and flexible for your food storage.. We have moved it 3 times and never had a problem. It is my wifes favorite appliance and fits our needs perfectly without a lot of bells and whistles. The ice maker filter is easy to change and the ice maker itself is super reliable. The model number is WRX735SDBM00. We have been Maytag and Whirlpool appliance owners forever because of their reliability and the ease of used to clean them.

I bought a Whirlpool front load washer, model wfw5620hw, July 19 2019. It worked for 5 months and quit working properly. I have been trying to get whirlpool to fix this piece of junk and have gotten nowhere. When I try to call them there is a 40 to 70 minute waiting time then I got transferred to another department for another 60 wait. This has happened several times in the last two months. I have never been treated so badly by any company in my life. I bought this machine from Menards and they just refer me to whirlpool so they are no help. I have two other commercial coin operated whirlpool machines and they have been great but this model is junk. Other people are having the same problem with it as I am having.

On 12-22-13 we purchased a new Whirlpool Washer- Model=Top Loading-WTW4800BQ. We also purchased Lowes extended warranty. Washer was delivered on 12-24-13 around 1:00pm. Connected washer. Washer filled with water. System started but would not wash. 10 minutes later it rinsed and drained but would not go thru wash cycle. We clicked the cancel button for 3-seconds to restart. Same problem. Called Lowes - Lady name Kelly continued to tell us we did something wrong. She would not listen and continued to say its Christmas EVE. Finally the workers came out to check it out around 4:00. Confirmed washer is defective and new washer will be delivered on 12-26-13. Confused as to the label on the machine says made with pride in America. Our 20yr. old Cabrio only lasted two years and went up. Never buy another Whirlpool product!

Lasted a whole two years, no warranty from Whirlpool. No biggie until I read countless complaints that Whirlpool OTR microwaves dont last. When I was young we had a Whirlpool microwave oven that lasted 15 years. Apparently this one (made in China) is the direction Whirlpool has chosen to take, cheaper products for higher profits.

Two years ago, we purchased a Whirlpool Cabrio Washing Machine from Sears. All of a sudden, it was making sounds in the spin cycle that sounded like a jet airplane taking off. It was terribly loud. We called repair technician, which cost $90, only to find out that the bearing is gone and its going to cost over $500 to fix it. This is absolutely ridiculous! We expected it to last several years, only to find out that we would have to spend almost as much as the washer originally cost in order to fix it. We paid $700 for this machine, two years ago, and I can say that Ive never been more disappointed with a product in my life. My previous washer lasted thirteen years, not to mention my dryer and stove fifteen years, with minimal repairs. I will never buy another Whirlpool appliance again. I have read some other complaints on this consumer affairs website, as well as other sites, regarding this same washer with the same problem on the bearing and cost to repair. If anything, I think Whirlpool should make good on this product and offer something regarding a recall or payment for repair in some form. As far as Im concerned, I will alert everyone I know about Whirlpool appliances and advise them not to purchase it. Now, I either have to pay over $500 to repair my washer or go buy another one. I do not even want this Whirlpool appliance in my house when I can get a washer for cheaper than the cost to repair it.

My Whirlpool dishwasher is 11 years old and has performed satisfactorily throughout. The utensil container is in the door, saving room inside but making it a bit less convenient to remove. The results are satisfactory, but I carefully rinse everything before putting it in the dishwasher. I dont believe dishes with hardened food would come out clean without this step.

The space could be laid out a little better. The flimsy shelf is not real stable for foods or ice tray. Where the shelf locks into the side wall is not deep enough to stabilize the shelf itself. The flat indentations in the bottom, where they meet the front, have an edge that makes properly cleaning the freezer a bit difficult.

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

I purchased the Whirlpool Gold OTC microwave model #GMH6185XVQ on November 29, 2010, and it was installed on December 26, 2010. After 18 months, the Magnatron went out. Its just me and my husband, and we eat out most of the time. So, it wasnt used a lot. I called Whirlpool, and Sherrie could only say that she feels my frustration. No, she doesnt. She has no idea. I just purchased $4000 worth of Whirlpool appliances, and now, I have no idea if they are going to last. It is a piece of junk that I paid good money for. In this day and time, we have to watch what we spend. I think Whirlpool should be a stand-up company and admit to taking our hard-earned money for a piece of junk. Dont they realize that its going to hurt their business.

My silverware, when it is washed, a piece or two comes through one of the openings in the basket and I have to work it out before I can lift it out of the dishwasher (MOD WDP320PAD50 Serial #F4432749) to put the pieces away. Please update your dishwasher by making the openings smaller for the silverware so I can stop cussing. Send me a new basket when you do. The dishwasher was in a new home I bought.

Whirlpool Gold Series French door, bottom freezer. - This fridge is beautiful. Thats as far as the pros go for it. The Freon is leaking and cant be repaired because of where the leak is coming from. I can always tell when its time for a recharge because it leaks water profusely when at a low charge (every 4 to 6 weeks). We paid over $1800 for this fridge back in 2013. It has been just over two years and we are now having to replace this fridge. I cant express my frustration at this point. Whirlpool wont do anything to help us. They told me, You are out of warranty, and thats all they have to say. Thats over a thousand dollars a year to own this POS when you consider taxes. Over $1250 a year when you consider the service calls along with it. I will not purchase another Whirlpool product ever again. I am disgusted by this company and their refusal to stand behind their product. They have literally stole money from me and are laughing about it. Do yourself a favor and stay far from Whirlpool.

My husband and I have been loyal Whirlpool consumers for over thirty years. When it came time to purchase a new refrigerator, we purchased the GC3SHAXVY00 model. It was quite expensive but we decided to splurge. This was the worst mistake. Let me also state that we have had the refrigerator now for maybe 5 years. Within the first 6 months, the door that is the central operating system for the appliance went out. The appliance was still under warranty at that time, so Whirlpool ordered a new door. The technician replaced the door and left. However, within 15 minutes of the new door being replaced, the entire refrigerator began to shut down, not just the freezer. Fortunately, we had the techs cell and we called him and he came back and put the old door on until he could order another new door. That made three doors in the first 6 months of us owning the appliance. Then, the ice maker started freezing up. We were told just to defrost the ice maker once a month, that this was a problem the company was experiencing with this 500-dollar refrigerator. Then, the water line started freezing so we would have to leave the freezer door open for about half an hour every week to get the line to thaw so that we could get the water to come out of the dispenser. Now, the ice maker has quit completely. Are we going to call a whirlpool tech? NO, what for?This refrigerator has been a true lemon from day one. I have three more Whirlpool appliances that have broken down within 6 weeks of purchasing them. It was time to replace our appliances so we thought we would support our local economy by purchasing Whirlpool. To say the least, that will never happen again. I will be replacing all my appliances with LG from this day forward.

For the last 5 years, 3 Whirlpool dishwashers. For these years been tracking to see how long they will work, but it seem like they are not build to satisfy the customer. Many telephone calls to service, but they will use the same lines, Nothing we can do... your extended warranty expired. From now on will look for a different brand.

Had washer less than 1 year and washer stopped and was flashing code F 51. Called Whirlpool and they sent a repair person. He worked on it and didnt fix problem. Called Whirlpool back. They had to order parts. Repairman came back - replaced parts. Now not 6 months later same thing happening. Whirlpool said we have to pay for labor to repair again. We went online after this happened the first time and saw where others had same problem - this washer should be recalled. The repairman said this part was corroding. This should not be happening on a new washer. We will never buy another Whirlpool product again!!!! Im concerned that it will keep repeating over and over and we paid 700+ for this washer not 1 1/2 ago. My last washer lasted 15 years!!! Wasnt a Whirlpool!!!

Had one double wall oven lasted 15 years with just about no problems until the control panel broke and could not be fixed. Bought another just like it and it is having problems after 6 months. Light wont work. Turn on from the control panel and the time does not work.

I bought a whirlpool W 10632082A a yr ago. I read the reviews and thought it was a good product. I was wrong. It has never washed the dishes good. It has terrible screens that always get clogged. The dishes never get dry. I think the dishes would get cleaner throwing them in the yard and spraying them off with a hose. I would not recommend this product at all.

I purchased this Whirlpool Aqualift oven at now bankrupt HH Gregg so my recourse is limited. I loved the look of the slide in range and the salesman raved about the quality of this appliance. First the ceramic top is a nightmare to keep clean, not mentioned at purchase. The Aqualift feature is totally useless. I use my oven on a very limited basis. Putting water in the bottom of oven does absolutely nothing to clean oven and even less on sides and oven door. I spent a substantial amount of money on this so called self clean oven and I am so disappointed in results. It does not get off even a minimum of spots, I would hate to have something actually spill over. Aqualift does not work and then you are advised to not use anything else to clean it, so what now?

I am so thankful that there are others who are having the same problems with their washers. Since 2006, my husband and I have had words regarding who is not loading the washer right, why are the clothes still dirty, and why does the dryer have so much lint. The excessive amount of lint ruined my dryer. I get UL codes all the time! Before the UL flashes, it sounds like someones trying to break in. It is 2011. Despite the problems, it has not died yet. I am selling it and will never purchase another from them again. I have the dryer and it went out 2 years ago. It has problems with the motor. You can guess I did not buy a Whirlpool.

I just replaced our Whirlpool Accubake Double Wall oven, model RBD305PDS14, because it fried the control panel after being put on self clean. This was the second time this has happened and I have probably only used the self clean feature three times since we purchased the oven. Im not a specialist in defective product design, but having a control panel burn up two out of three times when the self clean is used suggests a significant problem. I refused to pay to have it replaced again and obviously did not replace it with another Whirlpool product or any other brand associated with the company. I see that this problem has a long history dating back quite a few years with Whirlpool doing little or nothing to resolve the issue. (They just deny any knowledge about any defect in the design.) Fool me once, shame on you! Fool me twice shame on me!

I have a home that was new 5 years ago. My microwave/oven Whirlpool Gold was built in March 2005. The light bulb went out in the microwave 3 days ago. The users guide that comes with the unit says for this call assistance. I called the local appliance co. Cost to replace the bulb is $10 parts, $65 service call $25 labor thats $100 plus tax for a $.10 bulb! I called Whirlpool. What a joke, the biggest bunch of puppets paid by a Michigan based company who never heard of what happened in Detroit! They were no help and understood my frustration but flat did not give a **! For a $.10 part Whirlpool is willing to get bad press worth whatever I can amass!

Duet Washer GHW9150PH0 - The washer is about nine years old. Last year I got the dreaded F-11 error code, and had to purchase a new controller board and install it. Now the spider arm on the basket has snapped (cast part). Ive been on the phone with Whirlpool for over a half hour now, and all I get is We have to send a service tech out, and you have to pay for them. I have the broken part in hand, I know the Whirlpool part number, yet they want me to pay for a tech to come see the part and confirm it. Ive been unable to talk to a manager yet, none are available.Eventually the lady agreed to replace the broken basket, after telling me at least five times she could not, but she refused to replace the tub which was destroyed when the basket broke. Ill be calling back to talk to another agent soon.

We bought a complete set of Whirlpool Appliances three years ago. The set we bought were in the upper price range. In the past three years: The freezer began forming ice on the bottom which melted and poured water all over the floor (a unit on the freezer had to be replaced 18 months ago). An element on the stove quit working and had to be replaced (12 months ago). The ice maker quit working and had to be completely replaced (9 months ago). The dishwasher quit working and the entire motor had to be replaced (3 months ago). The ice maker quit working again four days ago. The repair person who just came said the entire unit needed to be replaced, AGAIN. He said the warranty on the part is only 6 months. I called Whirlpool itself - their warranty is only 1 year. The fact that their warranties are so short, and there are so many problems with their products is evidence that they do not make products to actually work. They simply make them to sell. They do not care if the product works once the consumer has paid for it. This was obvious in my conversation with the Whirlpool service person. She took 10 minutes to gather all my personal information then took 10 seconds to tell me there was nothing they would do.

I have purchased one refrigerator double door Mastermind 230 Ltr. capacity on 08/02/2009 at a price of Rs17200 from Himanshu Sales at Halol, Panchmahal, Gujarat. After one year, there was a problem in the refrigerator. My complaint was given to Himanshu Sales Halol. A service engineer came and replaced OLR and starting relay. I was charged Rs500. The bill was not given. Again cooling was not achieved. My complaint was given to customer car complain no. 22265 on 26/04/2011. Service engineer came on 10/05/2011 and reported that compressor get overheated. He has replaced compressor, capillary, gas, starting and overload relay and charged Rs1650. But compressor continued on, it does not cut off on temperature. I complained on 22/05/2011. Again service engineer came and replaced thermostat and charged Rs150. On 02/06/2011,again cooling was not proper. I complained on 05/06/2011. Service engineer came and advice to send the refrigerator to service center at Halol at our cost. After one week, it was sent back to me. Still ice not forming in freezer. We thought that it is due to summer. We also informed Himanshu Sales Halol. They advice to give complaint to customer care. Complaint was given on 28/11/2011. On 29/11/2011, a service engineer came and informed us that the compressor overheated. On 06/12/2011, the service engineer came with new compressor. He replaced the compressor, capillary, starting and overload. After gas charging, fridge was started. Still ice was not forming in the freezer and there was abnormal sound coming from compressor.Now we are tired to take service from Whirpool. I think this is a company defected piece, so send some senior authority to check the same and to take necessary action. Also due to this problem, my electricity bill got on higher side, and the purpose of the appliance is not solving. On 12/12/2011 at 11:30, the service engineer came and put some instrument to measure temperature at freeze on super cool mode and told that he and Samir will come to check the same. After that, compressor was in running mode up to 19:30 without cut off on temperature. Nobody has came to check,we called him. He replied that Mr. **, the regional head, will come tomorrow, 13/12/11. Still cooling is not achieved, We have registered complaint under complain no. AH1211007719 dated 13/12/2011.

Purchased first water heater in 2008 with 6 year warranty. In 2011, pilot light would not stay lit. Whirlpool told me to go to Lowes and get a new one at no cost. But I had to pay for service to identify the problem and installation of new one, costing $250.00. A year and a half later on a six year warranty, the same issue the pilot light not staying lit. They send a pilot light assembly and we pay the shipping and installation cost of $130.00.Two years later, the same issue begins again. Calling tech support, they determine it needs a third pilot assembly at $30.00 for shipping and $265.00 service installation fee by a certified Whirlpool technician. Worked one day! Im so done with this company!!!! I was promised a call from a supervisor with Whirlpool which Im still waiting on days later. Probably for the best at this point. I think I would feel better if I could beat the crap out of a Whirlpool CEO with it! Im cutting my losses and going with a different provider. I will NEVER again purchase another Whirlpool product!

This is a great choice if you like a drawer for a freezer. It’s double door. The racks are easily moved. There’s are drawers for beverages and cheeses and vegetables. One downfall is replacing water filter cartridge every couple months and freezer could be set up a little better so you don’t have to pack things on top of each other.

I bought the Whirlpool Cabrio top loader set in 2006. Honeymoon was over after the first year and I had to change the dryer element then the washer with the F51 code six months later. Last year, I had to replace the heating element again! For the last six months, I have been dealing with the dreaded UL on the washer. I cant afford to pay a technician $100 to come out and tell me whats wrong let alone what they will charge to repair a problem that, from the looks of this message board, will never be fixed. I have no choice but to get it fixed in order to sell the ** machine. I paid $1400 for this brand new set and have already invested $500 in repairs. How is this possible? I had a 20-year-old machine prior to this and never had an issue. There are lemon laws for cars, why arent there any for appliances over a certain amount? How in this day and age can a company be allowed to sell such garbage? I will never, ever buy another Whirlpool appliance as long as I live. Any other brand can have my money any day.

In 2015 door of top loading washer (Whirlpool Cabrio Washer) needed total replacement. Lucky I had an extended warranty. 2018 March, extended warranty expired and now have the exact same problem. Pretty crummy product if major part like a door has to be replaced every 3-4 years. We do not wash large items like blankets/quilts in this machine. That goes to a laundromat where there are oversized machines or to a dry cleaner. So the only reason for this breakage is a default in the lid assembly. There is only one phone number for customer service, repair, parts etc. Put in my service call and filed a complaint at same time hoping for at least a small discount. Ha! $100 plus tax for service call- part price ranges from $150-230 plus tax. Whirlpool could tell me the part exists but would not say how long it takes to get it! Do NOT buy Whirlpool washer with top load lid that has glass window. Big problem is that Whirlpool now has Jenn-Air, KitchenAid, Maytag and Amana all under their umbrella.

We got our Whirlpool french door refrigerator with freezer on the bottom (Model: GX5FHDXVY04) in June 2010. In the past six months, the refrigerator portion loses cooling and temperatures go to the 60s or 70s. We found out that by turning the unit off until it defrosts, it will work again for awhile. Weve had water overflow on our wood floor. When this happened the third time, I called Whirlpool to send a repair person.The person I talked to said it could be over $400 to repair and that it would be more economical to get an extended warranty for about $314, which I did. I did not receive the contract via email (it may have gotten lost in spam). The repair man came and said yes, this was a common problem due to a design flaw and that it needed a $6 part to make the water drain smaller - so that too much air didnt get in.It was May 1st before the repair could return to install it. This was done and we thought - expensive but its taken care of. Today, May 5th, the same problem happened and I have to throw away food again. Its the weekend and there is not a repair person available for two weeks - I got an order number and may request that the repair come sooner. To add insult to injury, I found out that the extended warranty is good only up to $450 and not good for any repair that might be needed in a year. Most of the repair goes to travel to get to Fairfield and labor and we have used most of the warranty already.

My Cabrio was built in April 2016, its now Feb 2019, and its not working. Shows error code of LF, the inlet water value is bad. I bought a Sears protection plan, repairman comes out, tells me no-one has the part anywhere, its backordered and no way to know when it will deliver. Sounds like a scam so Sears doesnt have to fix it and Whirlpool makes little to none of the part so you have to buy a new machine. This machine also takes forever to wash clothes, sometimes part of the clothes come out dry because not enough water. Its a huge tub, but of no use because theres not enough water to clean properly therefore, you have to do small loads. I always put it on high water because the other features like, quick wash & normal do not give but only little streams of water! The first one I had delivered made a funny noise from day one so Sears replaced it the next day. This one has NOT even lasted 3 yrs. There needs to be new legislation placed upon these companies with regards to the products they make. It should be illegal to make such junk and be able to charge high dollar for it and it doesnt operate well or last very long. They are laughing all the way to the bank on everyones dollar, intentionally making products that last less than a few years! I Will NOT purchase Whirlpool or any of their products again! They owe me a new Cabrio and Im going to make sure I get it and get my moneys worth! DONT WASTE YOUR HARD EARNED MONEY ON THIS JUNKER! DONT BE FOOLED BY ITS PRETTY SLEEK LOOK.

Whirlpool Cabrio platinum washer (JUNK. DO NOT BUY). As mentioned in other complaints, the Cabrio top loading washer is garbage. Sound during the spin cycle is VERY LOUD because of a bearing noise. The clothes dont even get clean, lint all over dark clothes. I am the only person in the household so the machine did not get used as much as a family would use it. DO NOT BUY THE CABRIO WASHERS.

The washing machine continued to display an F1 error code. I contacted the manufacturer and was told that they will not do anything about the problem due to it being out of warranty. This is the first time I have complained about a product or service and want to try and assist anyone who may be thinking of purchasing a washer from Whirlpool. I do not recommend purchase of these units.

I purchased a new water heater in August 2013. The pilot light started going out in October/November of 2013. After calling the Tech Support phone number, (877) 817-6750, I was advised to clean the burner screen. First this is very difficult to do because the burner screen is underneath the water heater and almost impossible to access. Second the closet the water heater is in did not show any signs of debris that could clog the burner screen. I did as they recommended. Several calls, and several weeks later, they finally authorized a technician to come and service water heater. He performed a cleaning even though he couldnt find anything to clean; and he replaced the control module. The new control module worked through the spring and summer seasons and then I started having issues again in the fall, late October. Started calling the same phone number and was told again to clean the burner screen. I convinced them to send out the technician again. The A and E Factory technician came out and only cleaned the burner screen and left before I had a chance to get home. This happened several times and I called Whirlpool every time. The next A and E technician told me to try changing out the draft vent chimney to a different size, which I did. Problem happened Again! I finally asked for another plumber and they sent me 3 names of their authorized plumbers. I called Phil, Philco Plumbing. He told me that I needed to have more ventilation, so I added more ventilation, even though I later found documentation stating I already had more than what was required by the manufacturer. Again, a week later, started having problems. Call back and asked to have my personal plumber come out. This time the rep told me that I have always been free to choose any plumber I wish (why wasnt I given that option the first 10 times I called?). My plumber came out and replaced the control module and the thermocouple, but wasnt convinced that these were faulty parts, he honestly couldnt figure out why I am having this problem, but it was worth a try. That lasted about 1 week and now I am having the problem again!!Whirlpool will FINALLY authorize a new water heater, but they will not authorize installation for the new water heater. I have already spent money on recommended repairs that have not worked. I have taken 15+ hours off of work to watch plumbers do nothing that has rectified my problems. And now Whirlpool wants me to deal with installing the unit myself, OR pay to have it installed! They say they wont cover installation because I purchased it more than 1 year ago. They seem to be missing the fact that I have had trouble with it the ENTIRE time I have owned it!This Flame lock system is garbage. I found on Consumer Affairs that a few years ago a class-action lawsuit settled, dealing with the same issues. I think it is time for another round! I KNOW that I am not the only one dealing with this problem because the plumbers I had out all had similar complaints from many of their clients. Whirlpool wont fess up to the problem, but the problem is real.

I purchased a new Whirlpool top load washer and dryer in 2012. I heard all kinds of crazy stories about all the new machines, so I tried to stay with the regular top load style. About 6 months ago my machine seems to have lost its mind! It forgets where it is in the cycle and pulls hot water when it should be cold and the washing machine has even overflowed all over my laundry room floor. I tried unplugging it, but thats just a temporary fix, it goes right back to its antics! I had my last washer and dryer for over 12 years. Im really upset that I spent a small fortune on this machine and now it needs repairs! Repairman is scheduled for next week. I will never buy Whirlpool again! JUNK!!!!