Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

I purchased a new home in 2005 and equipped the kitchen with Whirlpool appliances. Every single appliance has broken at least once. The refrigerator ice-maker has been repaired once and replaced twice. Some of the control panel buttons on the dishwasher work some of the time. Other times we have to strike the panel to make them work. Weve had to replace the handle on the microwave door twice at nearly $50 a pop. And the motherboard on the dual-oven has been replaced once. I will NEVER purchase another Whirlpool appliance for as long as I live.

We paid extra for a 10 year warranty on purchase from Airport Appliances. On delivery I commented that the plastic material used throughout the fridge was of very flimsy material and wobbly. In the first week the crisper drawer joint cracked to our amazement and they had to send another one from Whirlpool. In the 14th month after the Whirlpool warranty had expired, we found the pantry drawer lid/cover shattered by the door which shut on it because of no reasonable leeway provided in its design.On calling the special warranty people they said they only covered the compressor and parts and nothing else. Called Whirlpool who quoted $85.00 for the lid, plus S&H and taxes. Now we have an eyesore every time we open the fridge when we see the taped up cracked three foot pantry drawer lid. We badly regret giving away a 25 year old perfectly working Whirlpool Workhorse Fridge and buy this newer model which we will have to live with for a quarter of a century. I am 75 years old now. Never a Whirlpool again!

Purchased Whirlpool clothes washer Cabrio Platinum about one year ago. Never sufficient water to clean items. Appears that there is no way to add additional water to ensure that items are cleaned. Many items come out dry and still soiled.

Updated on 07/09/2020: This fridge freezes produce. A part was replace to solve this problem but it has never worked properly. After several attempts to correct temperature fluctuation, Whirlpool decided it was working within their specs and advised us to set the temp higher to solve the problem. So we are doing that but now if the temp is too high the ice is watery and falls out of the ice compartment when we have finished using the ice dispenser. So we lower the temp and it again freezes the produce. Do NOT buy a Whirlpool!!! If you have any questions look at whirlfreezefood story...Original Review: Purchased September 2019. Worked for a couple weeks and then Freezes the produce. I have put it in the center drawer and in the main fridge still freezes. Go to ** for full story and recording of a message Whirlpool left me.

The burners were very crooked and the pans got burned out right away. They were covered under warranty but since then, they had the same problem with them with the new items. They had the light bulb stuck and couldnt get it out, they came under warranty and now a new light bulb wont work in it. The control top indicator light didnt work so I had that fixed under the warranty, but now it has the same problem and I cant afford to get it fixed and it could be a real safety issue.When it was under warranty, I called about the brown in between the oven door and they said it was cosmetic. It gets worse every time we use the self-cleaning oven like the seal isnt tight. The outside of the door gets brown also when using the self-cleaning oven. We thought we would have this range for a long time as we had a Whirlpool range before which lasted 20 years. I will never buy a Whirlpool product again and we have had a lot of them. e cant afford to buy a new one so we are stuck with this one with all its problems. Whirlpool just gives you the runaround when you call. When they brought the range, the self-cleaning oven part wasnt even hooked up so they had to come back and fix it. I cant believe they dont have more recalls on these. I have only had this for 4 years.

Aqua clean does not work. I purchased this range this year not knowing aqua clean was different than a standard self cleaning. I had not use the range since its delivery in June until Thanksgiving. One meal in the oven and the turkey had created staining on the sides and the bottom. I have run the self clean cycle so far four times and scrubbed till I’m blue in the face. The greasy stuff does not lift off and the warranty voids if you use anything else. Have already contacted the dealer to see if I can return this!

Cabrio Whirlpool Washer - Bought this washer from HHGregg in Orange Park, Florida. This washing machine is horrible!! It does not fill the tub with water enough to even cover the clothes. Some of the clothes are not even wet. They just sit in dirty water, no agitation. Then it refills with water and the rinse water is dirty, there is no agitation or movement during the wash cycle. My clothes are stained and dried food and dirt are still on the clothes. My white clothes are now gray. This is the worst machine. I have tried everything. I am now hand washing the clothes and trying to add water to at least cover the clothes but the sensor just drains the extra water out. This machine is less than a year old. There should be a class action lawsuit against Whirlpool. I am not the only one; everyone that has this machine says it is a nightmare.

Whirlpool model WRF560SMYB04 - We purchased this model Whirlpool in Dec 2015 after having a refrigerator for 18 years with no problems. We started having cooling issues in late 2017 and finally an intolerable fan noise in April 2018. Researched it and purchased a fan. Opened up the freezer panel and found that the unit was completely frosted up to the point where ice had formed around the freezer fan and was hitting the blades. Contacted a repairman who came out and called in the issue to the Whirlpool tech line. He was told that he should check continuity on a couple of wires. If these checked out, the problem was the user interface board at the top of the refrigerator. We purchased a new board for about $100 and installed same. No change. I was now $250 into repairs and no further. We became aware of Whirlpool Service Pointer W10875533A which described conditions that we were experiencing. The issue was a coil thermistor that would corrode (apparently within 2 years) and would not provide accurate signals. Whirlpool also issued an instruction sheet W10902213 Rev A describing how to relocate the thermistor and protect it with foil and tape. My repairman came out, confirmed the thermistor ($54) was bad, replaced same following the Instruction Sheet. We were now out over $300 on a $1000 refrigerator purchased 2 years earlier.Whirlpool issued the Service Pointer (not to consumers, but to repair shops) in Sept 2016 (within our warranty period). We received no notifications from Whirlpool of the defective design. Nor did we receive a recall notice. Moreover, Whirlpool tech group must have known about this issue, but instructed my repairman to replace the interface board. Whirlpool knows they have a defective product out there but are doing nothing to inform the consumer or stepping up to correct the problem. We have contacted Whirlpool to recover our expenses...will let you all know how that goes. Anybody interested in pursuing a class action?

We have had this Whirlpool washer duet 5 years. It regularly rips shirts, underwear, socks, and sweatshirts. Jeans or heavy denim are safe but polos, hanes, or flannel are not. We have been putting our clothes into laundry bags and lingerie bags for a couple of years now to wash safely. Additionally it leaks out the front door. We clean it regularly and it still has mold growing on the rubber gasket - we do prop the door open also. All in all it is a terrible dryer. My previous Maytag was fabulous. I will never buy a Whirlpool again!

Bought this machine in Feb 2007 as a pair Whirlpool Cabrio. I loved it for almost two years. The control board went out, Whirlpool replaced it. A couple of weeks later, the F-1 codes started then the F-51 codes. On July of 10, it was code after code. It sounded like a jet taking off and constant unbalanced load. I called repairman and was told to go buy new machine as repairs would start at $500 and since I live in a rural area, no one wanted to waste their time. Two repair techs told me point blank they wouldnt even touch it. We paid $1000 for this machine and we live pay check to pay check. I spent four months trying to get Whirlpool to do something. I kept getting told I should have bought extended warranty. Machine has been sitting under stairs for over year waiting to see if class action or recall can be done. Also when control board was replaced, the repair man told me it was rusting away from the inside out. My husband had to find us a used washer and this thing has done nothing but cost us money. So much for efficiency. Everyone posting here also needs to go to Whirlpools Facebook page and post there.

Whirlpool Gold Microwave Hood Combo GH5184XPS4 purchased new on 12/2009. The plastic vent cracked where clip attached by factory installed screw. The vent fell off microwave on 10/2011. I spoke with Whirlpool customer service. It is out of warranty and recommended to buy new vent part ($40.00). The new vent broke once again on 12/2011, clip attachment location. Now, the plastic door handle is cracking. The customer service is sorry and recommends to buy replacement parts as long as they remain available. There are many reports of similar instances noted online. I live in a newly constructed condominium where multiple owners have had the same problems with their Whirlpool Gold Microwave Hood Combo GH5184XPS4.

I purchased a Whirlpool Cabrio and a one year extended warranty two years ago. As soon as my warranty ended, my washer started to malfunction. I recently started to receive the F-51 code and the washer shuts down at the spin cycle. I am angry because I spent just under 1200 dollars on a washer a little bit over two years ago and now, it is sitting in my laundry room taking up space. When I called Whirlpool, they told me I could purchase another repair warranty for $316.94, which would take the cost over 1500 dollars for this washer and there was no empathy nor compassion for what I was feeling as a consumer from the customer service rep. I spent my hard-earned money on major appliance purchase and I think that it is only fair that I get more than a two year usage out of machine that was designed to last at least six years according to their website. There is no way that this should just be my lost and cost me additional funds.

We bought a brand new basic refrigerator, freezer on top, no frills, no ice maker, no water dispenser (model #WRT359SFYB) in Dec. 2011. For months, things on the bottom shelf of the fridge would freeze. The more we turn the control dial down, the more things would freeze. Finally, everything stopped freezing, including everything in the freezer. After having to throw everything out, we called for service. One year and 4 months out from our purchase date and without an extended warranty, we were offered no help. The repairman said that we had a leak as a result of poor manufacturing and there was no refrigerant left. He filled it but said he needed to check with Whirlpool to see if they would cover the repairs. It turns out they wont. I called them myself and spoke with a manager who offered no options at all, other than paying more than the price of the fridge to have it repaired. I asked if they were okay with their product having such a short life, filling landfills and causing such problems for their customers to which she replied that they are man-made and have no life expectancy. Crazy! For a manufacturer of large, costly appliances, one would think they would stand behind their product more. She also said that she would file my complaint and would have let me know if there was a recall on the fridge or any of its parts. It appears to me that others have had similar complaints. I wonder what warrants a recall. I will never buy Whirlpool again.

Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.

I purchased a replacement gas range (whirlpool) approximately 3 years ago. Its not the top of the line, no bells or whistles such as a self-cleaning oven or such. I did love the three huge grates on top, one which is interchangeable with a flat grill. If it only worked it would be a decent range. The center oblong burner struggled to ignite in full from the beginning. Often, I light the thing with a grill lighter. But the thing that pisses me off more than anything is the F2 error that appears 70% of the time on the control panel when I am preheating the freaking oven. I am NOT replacing the control panel on a $400.00 range. What I have discovered is I can hit off my power at the main, not once, but 2-3xs and reset or over ride the damn thing. I read this F2 code is a common occurrence so I got to thinking, why? My conclusion is the heat from the oven is vented up & directly on the control board panel. Really now, whos bright idea was it to expose a control board to repeated temps of 350+? Hate this appliance. Next range will NOT be a new one, Im looking to replace this junk with something mom or grandma had that lasted decades, not a couple years. Shame on you Whirlpool for producing such low quality, disposable products. By the way, I just went through this with a new fridge so theres much to be desired with new appliances. Theyre junk, designed to fail.

I purchase a new Whirlpool Calypso with Catalyst Washing Machine in 2006 after a house fire. Thinking that I was buying a great machine. I was so upset with my house burning that I never thought about the washing destroying my towels, rugs and sweaters until it was too late on the guarantee. I called the company and ask if there were any more complaints about this machine, and of course they said no. I ask if there was a recall and they said no. I told them that there needed to be a recall of this machine. I so want them to see the towels that I have to use. I am so embarrassed of my towels that I have to buy new when company comes. I made no difference on the price that I paid for the towels. They all were destroyed by this Whirlpool Washer. I have had enough, I am buying a new Washer and it will not be a Whirlpool. I believe that the right thing to do is for the Whirlpool company to put a recall on this machine and give our money back. I had a friend that is in charge of another washer company and had him to look at it. He said that if that was his customer complaining about his washer that they would automatically bring the customer another new machine. I wish I had went with his company. Shame on Whirlpool for treating their customers like they have.

We purchased our Cabrio washer and dryer in 2012. In 2014 we had to replace the rollers in the dryer. Since then it makes a loud clunking sound and it has to go through at least 2 or 3 dry cycles to dry the clothes, sometimes more. The washer lid lock doesnt work very well anymore. Sometimes it wont lock so I cant get the clothes washed. It takes forever to get it to work. Ill never buy Whirlpool again.

Purchased a Cabrio large capacity washer. It NEVER seemed to get the clothes clean enough, and after the sensors and bearings went bad within three years (out of warranty of course) I gladly kicked it to the curb. I bought a Samsung that has been great. Id like to support USA made, but not when it is AWFUL.

My oven was 11 months old when I tried to use the self-clean cycle for the first time. 2 hours into the 4 hour cycle, the oven completely shut down, door locked shut and no lights on the control panel. The repair tech came out on a warranty repair call (no charge), explained that Whirlpool does not use a thermal protector rated for a self-cleaning oven and that it blows every time. He then proceeded to replace it with the same thing because he is only allowed to put in the recommended part, which is not rated for the high temp cleaning cycle. So the oven is usable, but not the self-clean. Since I am at the end of the 1 yr warranty period, even if I were able to get Whirlpool to replace the oven (ha!) there would be no warranty because I only get the original time limit. So if I had a new oven and it blew out, it would not be under warranty for fix/replace. The repair tech said this is a COMMON problem with Whirlpool self-clean.

The oven has not worked correctly from day one. I have to use a thermometer plus after the correct temp is indicated I still have to wait another 15 minutes for the oven to reach the desired temp. Also have to set the temp for 25 degrees higher than the one I want. The burner that supposedly has two sizes in one is basically useless. Temps are not correct and sizes are misleading. There is a tiny groove around the outside edge of the stove top that gathers crumbs which are hard to clean out.

Help? WP Gold double convection wall ovens WOD93EC0AS rated very high by Consumer Reports installed end of February. Monday April 6, fan in top convection oven came on suddenly while oven not on. When I tried setting a baking temperature in top oven to see what was going on, message read This function is not available. After about 15 minutes the fan went off, and I could use the oven. Worked well Tuesday and Wednesday. Oven not used again this week, but this evening, Friday, same thing happened again. Process has been repeated several times with fewer times between fan turn on. Have turned off power to ovens until I can get a repairman. Has anyone else had this experience or know what the problem is. Have been reading about the problems with WP ovens. Wondering if I need in addition to Home Depot Warranty the one from Whirlpool as well. Had Bosch convection ovens for 12 years then self-cleaned and thermostats went out and cannot be replaced because parts no longer made or available through any supplier. Said I would not buy Bosch ovens again because the parts became unavailable even sooner. What a mistake. Apparently self-cleaning element blows a lot of ovens thermostats and/or circuit boards. Loved the ovens and had only one repair after the ovens were one or two years old. The Bosch dishwasher is same age and still working great and usually cant even tell it is on.

The lid stopped locking just over one year after I purchased a Whirlpool Cabrio top load washer, which disabled the washer from washing. After investigating, it seems the electronic control board needs to be replaced, which will cost $400 just for the part. I have a large family, including a disabled child, and a washing machine is mandatory necessity that I cant afford to replace after only one year.

I have had this machine (Indesit IWDE126 Washer/Dryer) for a very short time; the washer is great. It does a 20 minute daily wash which is good however the dryer part screws up everything you put into it and ironing, even with steam, makes no difference at all. The WORST part is the organisation DONT CARE. I wrote to the Chief Executive, Jeff Fettig, who neither acknowledged my complaint or responded to it. I made this complaint in October 2016 and STILL do not know what the outcome is. If you are reading this review I honestly would look elsewhere for a better machine. Try MIELE. They are expensive but 2000% better.

Whirlpool washing machine #WTW58ESVW1 - I bought this thinking Whirlpool was a good brand name. I was totally wrong. My machine is two years old and the auto sensor switch has quit working 6 times. One time it only did 6 loads of laundry. Another it only worked for 6 weeks. That time I replaced the switch myself to save money on a repairman. Ironically the switch is still under warranty but they will not replace it unless a serviceman comes to confirm that the switch is dead again. This is because 2 have already been returned to them. Obviously, there is a problem with the switch. The company will do nothing. They used the excuse that I did not purchase an extended warranty. This is merely an excuse. Do not purchase any Whirlpool products. You will be wasting your money and time having to end up going to go out to do laundry.

We recently purchased a refrigerator from a reputable local appliance store after months of shopping and comparing and research. As an opinion, Whirlpool seemed to set the standard for a quality appliance. Unfortunately, we failed miserably by buying this side-by-side fridge. Two unsolvable problems. First, the cold side door is extremely difficult to open. Ive tried ALL gasket lube methods and failed. Second, the stainless steel used on the front of the machine is obviously low grade that accepts magnets and is almost impossible to clean weekly without streaking. They were kind enough to provide us with their special cleaner {free} but it takes about an hour and a half to use for moderate success.The lady on the help desk listened but seemed rather cold and uninterested in the problems. At this point, we would be willing to pay the extra and go to a Kitchen Aid instead. Our advise is beware of these types of issues and get some kind of guarantee from your store when buying a WHIRLPOOL refrigerator. This is simply terrible.

The Cabrio washing machine I was told by salesman best made so I spent big $$, makes sense right?! Wrong! During spin cycles sounds like jet plane taking off, was told barrings or drive shaft is at fault cause water seeping inside, causing rust, Whirlpool didn’t seal it or designed it to ensure no seepage. Never again Whirlpool. I’m done with your ineptitude, Type: 580. mod. WTW6500WW1. Set.# CY4970595.

I bought my new Whirlpool Duet washer in April 2011 and the gas steam dryer in May 2011. In October 2011, the washer started to make a loud banging noise when starting the spin cycle. I contacted Whirlpool, and they scheduled a service call and stated that the washer was out of service. I told them it was and that I just bought it in April 2011. They said that the repair guy would need to see the receipt. Well, the A&E Factory service guy came out and said it was the bearings. Whirlpool only replaced the bearings with the whole tube unit and a few other parts. I was never told that all these parts would be mailed to my home, until I got a call from A&E about the tube being on back order. I was told that the part wouldnt be in until November 21, 2011, and it would take another week or more to schedule for a repair guy to come out. I called Whirlpool Executive Office (269-923-5000) and complained about all this. They said thats how it works--they ship everything to the customer and that there was nothing she could do about the back-ordered part. So I called Lowes corporate office and told them what was going on and asked if they could push Whirlpool into fixing my washer faster. About 4 1/2 hours later, I got a call from the assistant store manager; and they said that they would replace my washer with a brand-new one and would have it delivered in 2 days. Now, that was going above and beyond what I thought they would do. Just another reason why Ill continue to be a Lowes customer.Now, here it is, April 2012; and my dryer is leaking water into the drum. On Saturday, I went online and scheduled a service repair for Wednesday, April 25. Today, the 24th, I got a call from VIA that they would be out tomorrow and that I would owe them $120.00 for the service call as my dryer was out of warranty. Here we go once again, having to battle Whirlpool! I really dont give a dang what their dang system tells them about when I bought their product! I know when I bought it. And why did they keep telling me that Im wrong? They did almost to the point of calling me a liar!I called the Executive Office again and had to leave a message. Mark my words, I will never ever buy another Whirlpool product again! I will make sure that I tell everyone who I know at work and at home about the way Whirlpool handles their good customers!

I bought the Whirlpool Cabrio model # wtw5500xw2 about two 1/2 years ago. Besides my clothes not clean, I havent have any problems with it until recently. Usually it doesnt spin. The clothes are left soak and wet. First the belt broke, then the lid lock, then the nut came off the pulley, then the splutch assembly. There was a few more problems in there. Now who knows what is wrong with it? It is one problem after another. It is a money trap. The CEO was just after money. There needs to be one big lawsuit against Whirlpool. After I find out what is wrong with it and the cost to fix it, I probably will just go buy a new washer/dryer set. And it will NOT be a Whirlpool.

The plastic holding the vegetable drawers broke and now they are cracking because nothing is there to hold them in place. This fridge has a freezer on the bottom, which I like. Unfortunately, I had an Amana before this and it was wonderful- just old. I had to settle for a smaller refrigerator and that is part of the problem.

Purchased a whirlpool water heater 04/08/2005 and it worked for a short time. It had a 6 year warranty. I had to replace the thermocoupler assembly 1 time and it worked fine until last week. 09/02/1011, 4 months after warranty ran out, the unit started leaking severely from the top ? (Could of understood the bottom) here. After investigating further and being told to basically pound salt by the warranty number I called, I removed the top cove r(glued on by spray in insulation) and carved away the spray in insulation. All the bosses/threaded fittings for the inlet outlet and anode rod were all leaking under the insulation where it could not be seen! I know for a fact this unit was leaking long before the warranty expired! But because of the way it is built it is impossible to see it!. I strongly feel this was a manufacturing defect and there are hundreds if not thousands of these units in people houses all over the country!

I purchased the Stainless Steel, side by side with water and ice dispenser, model #WRS325FDAM04 on 11/30/16, paying over $1,600 for the refrigerator. We had trouble from the beginning with the freezer door not closing all the way. When the repairman came out, he said the entire door had to be replaced, as it was warped. Since then, one by one other items are breaking in the freezer and refrigerator. The plastic casings holding the glass shelves have broken on all three shelves in the refrigerator, the wall of the refrigerator and the freezer is cracked in several places, the ice bin has a hole in the bottom, where the device rotating the ice out broke and now when used, ice falls into the freezer, and the bins in the refrigerator have broken as well as some of the door shelves in the refrigerator and freezer.I called Whirlpool before posting a review to provide them an opportunity to at least offer to help in some way. Their response was due to so many pieces missing/damaged they would not be able to help in any way at this time. I purchased a Whirlpool product as I expected I was purchasing a quality product with quality workmanship from a reputable company. I have been sadly disappointed and will no longer support Whirlpool by purchasing any item manufactured by them and will share my experience at every opportunity.

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

We purchased our Whirlpool range a few months ago. We have the 6.1 cubic oven which is large inside with 5th element on top for keeping things warm which is a nice feature. The oven wipes easily if any spills occur. The only issue I have had is the top scratches easily. I used Creams Brute to clean the top which does well.

Oven was purchased new from Home Depot. Right off, the top black glass surface got scratched. Not sure how it happened. Seems to scratch easily. Then, the oven temperature for baking was found to not hold consistent. While pre-heating the oven for 350 F, the temperature goes up to 375 F, then well into the baking time, can drop to 100 degrees less (275 F). Oven feature is called accu bake. It ruined the baking and seems to be anything but.

I purchased a 50 gallon Whirlpool water heater, model FG1J5040T3, in November, 2005, and have had the same experience as reported by the hundreds of others, whose comments I have been reading. Basically, pilot wont stay lit. I called Whirlpool, relight the heater, when it doesnt relight, wait to receive repair parts, call a plumber, and pay to have them install it, then repeat same problems. Each time going for a week or so, without hot water.After relighting the heater 10 times in the past year, and service calls, Whirlpool authorized me yesterday to return it to Lowes, and get a replacement. I need to hire a plumber to unhook it, haul it to Lowes, get the new one, and install it. It cost me about $300 to $400. Will the replacement be any better? I am considering just replacing the heater with one made by Rheem.

Hi Folks, so today I had the pleasure to speak to Whirlpool regarding a repair bill on our washing machine which now has a bearing failure and estimate to repair was 1279.00. Its 6.5 Yrs old, just out of extended warranty and cost me with the pedestal a total of 1250.00 when new. I explained that in the 6.5 since I have lived at this house where we spend all new Whirlpool Gold Appliances, half have now failed. Range Microwave, Dishwasher and now the 1250.00 front loader is dying a slow and agonizing death with a bearing failure. Just so everyone understands, the estimate is from an official Whirlpool repair service that was booked through the Whirlpool website. Other repair folks just would not bother to look at it when I told them I believe the bearing was going bad.The repair man that arrived was professional and on time. However, I had a hard time understanding how a 6.5 Yr old washing machine would be considered beyond economical repair by costing 1279.00 to repair. Labor was 250.00 which I thought was fair. Time, etc. But parts made up the difference in cost. So later in the day, I spoke to Whirlpool and they offered the equal new washer for what would seem an excellent price. About half off. Wow, I thought that sounded good. So I asked if my existing pedestal would work with the new washer and it did not and I would have to pay for one. Regardless if my old one was fine or not.So, they offered a discounted rate from new at another half off. Total approx 800.00. So, I asked the Whirlpool rep to hold on and I need to check with my wife if she wants the replacement. She uses it as much as I do and wanted her thoughts. She checked the model on the washer and pedestal and with the local Home improvement store, they have it on sale for both units (washer and pedestal) and its about 50.00 less?Consequently, I called Whirlpool back and explained that it does not move the needle to regain my trust as compensation on a 6 yr bearing failure, failed dishwasher and range microwave they offer what a distributor of their product can offer for less as a package? Really? I mean, the Home improvement store is not in the business to lose money. Now, I am having a hard time understanding my own failure to have trust in a brand I used to have with my previous house.My mom had an old Whirlpool washing machine that lasted 25 years before she and my dad gave it away. You know, the old white top loader they used to make back in the 70s. Sheet metal, made a racket and never broke? Oh yeah got the clothes clean too! I dont know what to make of it anymore. So, I will just wait till it dies and take my hard earned money and spend it on another brand in my next house which we are going to move to soon. Maybe I can feel nostalgic and find my moms old washer. Its probably washing someones rags right now and getting them clean. It must be 35 yrs old by now.I dont expect to get anything for free. Its out of warranty, so I need to deal with the consequences, but there are steps the other party can take to help remedy the situation. I think they tried and it was genuine but in my thoughts its just not enough when your local box store is offering the same. When you develop a brand to extend a message of trust in quality and value, you need to have quality and value all the time. I suggested they help with the costs on the parts. I would certainly pay for the labor. Parts cost little to the manufacturer. Unable to help that way. I thought it was cheaper for them too. Guess not. Its come to be a throw away washing machine at 6.5 yrs and I am Infinitely disappointed. I just want my washing machine to work as well as my mothers old one and have the possibility to fix once in a while when needed.

I have had my Whirlpool stove for over 30 years and use it daily. Still a great stove. I would not trade this stove or any of the new types. I just need to get the self cleaner repaired. The only problem I have is finding parts to fit this older stove.

I have many rentals, and for over 39 years have always bought Whirlpool dishwashers for them and my own home. I have noticed over the last 15 years or so they are getting more and more poorly made. First I quit buying the plastic tub ones because they collected mold on the back. Then putting one in a rental, we went through 3 brand new ones that all leaked before we got a good one. Now, I bought the very best for my home 2 years ago, had the pump replaced under warranty due to leaks. Now, the plastic upper rack wheel has snapped off its plastic base. For under 30 dollars you get a replacement kit for it, that is all metal. So why didnt Whirlpool just put in the metal ones and charge a little more. So this will be my last Whirlpool, and all the brands they make. Do your research, many of the name brands you know are all made by Whirlpool.

Purchased Whirlpool Duet wfw9550ww00 in 2012 from PC Rich, who purchased machines in 5/11. Product stopped being made 5 yrs prior. Of course I did not know until my washer went and had service come to my house. He explained prior information, looked at my machine for 2 seconds and said someone put in a heavy load that machine was not able to handle and 2 belts broke and guts of machine are destroyed. Its a $799 fix, not including labor, youre better off buying a new machine. How does he know thats the reason for breaking??? The machine is 2 years old, not a scratch on it!!! Unbelievable!!!! Then states thats $114 for the service call. $114 for 2 seconds!!! Im absolutely furious!!! Whirlpool has a new program (if it helps anyone), if your machine is fairly new they will give you a invoice for 1/2 off a new Whirlpool... Take it from there. There should be a tremendous action lawsuit, look at all these complaints...

When I purchased my Cabrio washer 31/2 years ago I didnt bother to check reviews since Whirlpool was suppose to be the best of the best. An expensive lesson! A washer that spits out codes?!?! Whos got time for this? We paid 899.00 plus taxes for it, now we paid a repairman 99.00 to tell us its not worth fixing. He said the bearings were completely shot. As he was leaving he said his next service call was for the same type of washer! Whatever happened to appliances that last! Going green is all the rage but yet everything from cars to appliances is built to last only a short while. Judging by these reviews I cant believe Whirlpool didnt recall their garbage!

I purchased my Whirlpool washer on June 28, 2011. Within 4 months, I had to call for a repair. It is now going to be a year and I am on my seventh repair call. The repairs have been everything from loose pulleys, new belts, and new valves. When I called to complain, they said there is nothing they could do and I should take out the extended warranty. I have had washing machines last up to 15 years. Needless to say, they werent Whirlpools. I really would like to have it replaced. I dont think its fair to me that I should have to wait for a repairman to come out and tell me he doesnt have the part and has to come back. I did take out the extended warranty, which cost approximately $150.00 and that should not have to be.

Wife and I bought a WRF990SLAM00 fridge in 5/2013. Seemed like the nicest model Lowes had at the time. The first one delivered had problems: it wouldnt stand level or seal properly, and had to be replaced. Another unit was delivered a few days later. This one - the same model - worked very nicely, for a year and a half. A few days ago, it got loud. My wife noticed in the freezer, some things were beginning to thaw. We called Whirlpool, who said, Oh, its over a year, and youre out of warranty. Sorry! Ok, so they suck. After we had a technician examine the freezer, he suggested, This is something Whirlpool needs to address. It wasnt the first (or fourth) problem with this fridge that hes seen. Called Whirlpool again, this time to gripe. Sorry, youre more than a year, so no warranty BUT, well sell you a service contract for $330! Hows that sound? It sounds like Whirlpool just disqualified themselves from ever getting their hands on another dollar from my family. Theres too many other companies who DONT treat their customers like garbage.

Do not buy a Whirlpool refrigerator. This is the 3rd time I have to call in repair for the ice maker in 4 years. Water poured out on my floor for the 3rd time ruining my floors. Called Whirlpool and said there is nothing they can do to help me. They don’t care about their Customers! I could have bought a new one by now based on repair costs. They don’t back their products. I’m really annoyed now!

This is new and replaced an old model that was not doing the job. This new one seems to be ever so much better. The dishes are clean and I no longer have a white residue on the dishes and utensils. It is easy to load. I miss having a silverware separator for the holder because the silverware tends to be too close to each other. I always rinse things well before putting them into the machine because I usually run the machine about once a week. Overall, this is a good machine for the price I paid. I am loyal to Whirlpool and this one on sale was a very good value. Very pleased.

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..

My Whirlpool microwave broke. Im not sure how or why so today I purchased another 2 actually. Both were too big. The model I purchased is discontinued. I had to remove part of my Marble Backsplash - the turntable is tiny however mic is huge. Work on making microwave for smaller areas. Stick to get or Samsung for a nice size microwave not a Mongo mega oven above your oven.

GX5FHDXVY04 French door fridge. Ice maker backup issue - which cause water to build up and leak out of fridge. Fix was a known issue with a rubber grommet - $100.00. Fridge stopped blowing cold air - control board - $293. Fridge stopped blowing cold air again! Getting Nowhere with Customer service... Whirlpool used to be a great brand. They have lost me as a customer, and by the looks of this board, Facebook page, I am not alone!

Whirlpool GX5FHDXVB03 french door refrigerator: Continual water leaks. Condensation freezes in bottom of freezer compartment then leaks out on to floor. Per repairman, this is a common problem with this model which theyll come out and fix (remove ice and run hot water done drain line for a cost nearly $150) but it will happen again and again, etc. I cant tell you how many times weve had to perform this task. This is an engineering design defect that Whirlpool should fix.

Whirlpool Gold Fridge - For all the people who have water collecting at the bottom of their freezer... There is a plug in the drain pan underneath that needs to be removed. It comes that way from the factory. Thank God, I have a smart Hubby and Father-in-Law. I find it INSANE that these Repair people have not caught on or do they just want to keep billing for Service Calls.

Your Whirlpool French Door model # WRF993F1FM is a piece of junk... Had the fridge less than a year and had to have repairman come and fix it twice already... Would never buy Whirlpool Product again. Builds up ice in the refrigerator and then loses of most of the food in it. Leaks the water right onto the kitchen floor...really pitiful to spend more than 2000 dollars for a fridge that is a piece of junk.

Never buy a Whirlpool appliances because I bought the top of the line washing machine and after 4 years I had to replace it. And then I bought the top of the line refrigerator and after 6 years it goes out!!! I definitely will not recommend a Whirlpool ever!!! And me and my husband do construction and are asked a lot for a good appliances and we will tell our customers not to buy because Whirlpool is assembled in Mexico and their products are not worth putting in stores!!! Whirlpool is not the appliance that anyone needs so I definitely will tell everyone I come in contact with!!! Very dissatisfied!!!

Whirlpool Duet WFW94HEAW0 Washer - Bought the machine in Feb 2014 and was generally very pleased with it. However a few weeks ago we started getting oil/grease stains on clothing. Wasnt sure what was causing it but it has now got so bad that the machine cant be used. An internet search indicates it is possibly a ball racer ring and doesnt sound an uncommon issue. A call to Whirlpool resulted in a quote for circa $350 for a service call. Thats a 1/3rd of the original value (includes a 12 month warranty). And its just over a year old!!! We had a problem with the Maytag Neptune that ended in a class action suit and now this replacement machine seems to be even worse. I would recommend anyone to really consider what to buy and give this range a miss.

We just purchased this Whirlpool Washer. It is so awesome. Has all the many features I was looking for & we purchased it on sale. But really since using my washer I would buy it again even if it wasnt on sale. I love it. I have never been disappointed with Whirlpool. Everything I own in appliances is Whirlpool.

I have a 4.5year old Cabrio washer. Ive replaced the water pump 3 times due to a weak plastic part which keeps blowing out due to pressure. Now, the unit is leaking rusty, black fluid from the bottom. I purchased it at HH Gregg in Indianapolis, In. Svs tech called. They have never seen this on such a new unit. Parts and labor will equal $400.00. Calling whirlpool customer care did nothing. I offered to pay the labor of $100, If they would be willing to pay for parts. Talked to a supervisor who offered to sell me an extended warranty costing $300.00. I am a stock owner in Whirlpool, no joy, dissatisfied with faulty product. They are unwilling to make this situation right. The unit is poorly made. I think a $800 unit should last longer than 4-5 years. In 2006, Whirlpool stopped offering a 5 year normal warranty on their units. Supervisor would not let me talk to anyone else.

Hello, Here is our story. We bought this refrigerator Whirlpool - 26.2 Cu. Ft. 4-Door French Door Refrigerator through a local reputable retailer. After 16 months we started to have problems with ice melting in the ice bin. We continued to have problems related to cooling/freezing within the refrigerator to the point where almost all the major parts were replaced. The good news is the dealer negotiated with Whirlpool to have all repair costs covered after the first visit. I asked about just getting us a new refrigerator and was told Whirlpool requires a part to be replaced 3 (THREE) TIMES before consideration.In summary, the refrigerator could not be fixed and was condemned in agreement with both Whirlpool and the Dealer. Here is the interesting news - since the refrigerator was out of warranty (12 months and now we are at 18 months), they are requiring we pay $600+ for the replacement. Buyer beware - either pay for the extended warranty or risk having to be inconvenienced by having your refrigerator unavailable for days or in our case, weeks!

I had an addition added to my home in 9/2007, which included a new bathroom. A whirlpool hot water tank was added. This week, I woke up to no hot water, so I called the whirlpool customer number regarding the warranty on the model FG1F4034T3NOV. T hey told me the serial number shows its out of warranty, although I may have only had it since 2007. They also said there was a screen that needed to be clean under the bottom of, it that if not clean, would make it stop working. Since homeowners where not cleaning it, they have made a replacement door part that would fix it, and do away with the problem, but I would have to pay $35 for it. I asked them, since the serial number shows that the part has not been replaced on this unit, why not just send it to me, and I pay to have it put on. The person said no, you will have to pay for it if I wanted the part to fix it . Although my builder did not give me the receipt for it, thats just not right. If a manufacturer knows they are having problems with their product, which require a part replacement, and they have produced one, they should be willing to give the part to everyone with the product that request it. On top of that, this model has the left hand threaded thermocouple, which no one around seems to carry. I am totally disappointed with Whirlpool, and right now would not consider buying, or have any more of their products installed into my home.

I purchased a gold series whirlpool dishwasher on July 20th 2014. Today is Dec 31, 2015, for the past month I have been troubleshooting my dishwasher by myself. Because I had a maintenance man here already since I bought the dishwasher and due to Christmas cannot afford another 250 for another visit. Every time I try to wash, at end of any cycle I have tried using, I open the door and find the cascade soap sitting on the bottom of the tub, the dishes still wet and dirty. So I take them all out and hand wash them, I should not have to do this on a washer that is a little over one year old considering the price tag that I paid for it. I am not young anymore and if I wanted to hand wash dishes, I could have used that money for a nice vacation somewhere.The washer stops, start button blinking, I open it up, check it out to make sure everything looks ok, close it and restart again. It sounds like it is working, so I go about my business and come back an hour later to find the same issue. Dishes will not wash soap on the bottom of the tub again. This has been nothing but trouble since I purchased it. I have never had a problem with my old dishwasher until it got too old. On top of it all, I had to buy another clothes washer from the same manufacturer that now took over. This was only 5 years old and the motor burnt out. I had two maintenance men here from the Maytag/whirlpool company and they filled me in. So I had it hauled out of here and I bought an LG for another good price. It seems to me that it is all about money and they make nothing but crap. Now. I need to make another decision. About this POS dishwasher! What to do?

I purchased Whirlpool electric hot water tank in May 2011 (model no. EEZ80HD055V). The water tank was working fine for four months. It does not work anymore. I tried to get a hold of Whirlpool customer service. But I couldn’t get a hold of customer service at 877-817-6750. It is motel business without hot water. We could not open the business. We tried the best we could, but there is no contact or support from Lowes or Whirlpool. We have no other choice other than replace the hot water tank. We tried to find the right phone number to explain the situation to Whirlpool customer service rep.

We bought a Cabrio washer & dryer September 2010 for a room addition that wasnt completed yet. We didnt get moved in until the first of November. So the washer wasnt used until then. In January 2011 (15 months later) it stopped spinning so clothes were dripping wet. We called Whirlpool and were told that they would be happy to set us up for a service agreement for $322 for one year. We declined since we bought the washer for a little over $500. When we had a local Whirlpool service man come out and he determined that it was the control board which would cost $265 (Whirlpool only warrants parts 90 days). I sent an email to Whirlpool and was told too bad, so sad. We called their customer care line (that is really not the term for that phone center) and asked to talk to a supervisor, who essentially told me the same thing. Whirlpool is making equipment that is extremely poor quality. There is no incentive for them to produce a better quality product as they make money on the extended warranties that are necessary, or if you dont buy an extended warranty they charge an extraordinary huge price for their parts, which they dont warranty. We will never purchase anything made by Whirlpool. I am not sure where this useless piece of junk that I have will end up but I intend to let everyone I know what a terrible company Whirlpool is to deal with.

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

Whirlpool oven WOD93ECOA501 - This oven will most likely lock up if you use the clean cycle. I wish there was a class action suit in California. This happened first time I used the oven. Very expensive to fix, and though it was 9 months after a kitchen remodel, it was not under warranty because we bought it early and it sat in garage, and Whirlpool could only use purchase date. This is not new technology. Upper and lower oven both locked. Wish I had bought a Blue Star oven, as my Blue Star cook top is fantastic and a pleasure to use. HAS ANYONE GONE TO SMALL CLAIMS COURT?

Had to return my first 2019 purchase due to refrigerator freezing food and imbalanced top doors. I was unable to get straight answers from Whirlpool and so the mgr at BB gave exchange same problems except door not as off. Cheap product make/model. A class action lawsuit from 2016 has occurred and the company continues to distribute the same issues in their new make/model.

Model # WRF990SLAM00 Ser# K23919328 - It should be possible to rate this piece of junk zero stars!! Purchased on Feb 2013, it is driving me and my wife insane. It is noisy compressor wise all the time (Our kitchen and living room in the townhouse are one room). The problems started after the hurricane in 2016 killed our power for three days. I had to shut the refrigerator down to manually defrost the freezer section because the fan on the fan-coil was hitting a huge accumulation of ice. Then the weird blackouts started approx once per month where the panel light as well as the interior lights went on and off every minute with that dreadful BEEP. This went on for over 24 hrs and made living in the same room HELL. The beep and three clicks happen every minute and the cooling is none. Whirlpool service came ($80.00) just to look at it and will come back with the rest of the bill which probably will be astronomical. I feel cheated big time!! Minute and the cooling has worsened big time. Whirlpool service came ($ 80.00) just to look at it and stated it needs a new computer board as well as a new front panel on the left door.

Whirlpool side by side - What more can I say? A 1-year warranty is all Whirlpool can afford to give anyone since the compressor broke a few months after. They are paying for parts, but we are paying $300 for labor to fix a $1,200 fridge... in addition to having to be without it for a month, losing defrosted food, etc. Fortunately, the dealer gave us a loaner.

I am completely dissatisfied with the Whirlpool Cabrio top loading machine. Our washing machine is less than one-year-old. It doesnt get the clothes clean, especially the darks, and it is so rough on the clothes that they come out twisted tied into knots. The dark clothes come out dirtier than they went into machine. Even though we use the dark detergent on the dark clothes and program for an extra rinse cycle, the clothes come out with white powder all over them. They need to be washed again and sometimes again. And sometimes they still dont come out clean. That is not very energy efficient. The clothes come out of the machine so wrinkled that everything needs to be ironed. I can imagine making washing machine that doesnt do its primary function, which is to get clothes clean. Todays families do not have time for this extra work.

I bought my Whirlpool water heater from Lowe’s in 2010 and now 2 years later, the pilot light keeps going out. When I tried to buy replacement parts from Lowe’s, they stock parts for other brands but no parts for the brand they sell. The water heater is junk and Lowe’s is no help. I will not buy from Lowe’s again.

Whirlpool Wash-And-Go washer and dryer - I purchased these new November 2016. Since week two, they have been a constant problem (i.e. not enough water to even get clothes wet, forget about clean; gulping soap from the dispenser; rubbing holes in clothing; putting rust on washed items). The dryer NEVER gets the clothes dry; no matter what setting they always come out damp, even after Ive put them through for two cycles.Three separate repairmen have come to work on the washer replacing sensors and the entire control board. It worked fine for two weeks, now its back to guzzling soap. (It is supposed to do up to 12 loads on one refill of detergent. I get two per refill. Ridiculous! Soap isnt cheap!) And, today it ruined brand new bathroom mats with rust all over them that I had to hand wash to try and remove without much success. At this point I would advise anyone looking for new appliances to try any other major brand and NOT Whirlpool. As soon as I can get the money, these are being junked and Im NEVER buying Whirlpool anything again!

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

Takes 2 or 3 full cycles to dry small load. Big disappointment, drying is such a horrible experience since the clothes never dry when I expect them to. Not satisfied at all.

I originally purchased a Whirlpool hot water heater in 2005. After numerous problems Whirlpool agreed to replace January 2010. With the new hot water heater, everything was fine for the first two years. Now about every 6 months, we are having the thermocouple and the igniter. Each time you order the part, the part is free but you have to pay $30.00 for shipping. I am tired of dealing with this. We have decided even though we still have a warranty left on the hot water tank we are going to purchase a different one and never ever buy another Whirlpool product. They do not stand behind their products.

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

AquaLift Self-cleaning does not do the job as advertised. It does very little to clean the oven. Sitting-on-the-floor-in-front-of-the-oven scrubbing is what is needed to clean the oven.

We purchased a Whirlpool Cabrio washing machine in September 2006, and have had nothing, but problems. I constantly have to get online to check error codes. Several months ago, the washer just stopped working. We called Whirlpool technical support. They said wed have to pay for a repair. After several calls to Whirlpool for help, I found online references to a recall for the same problem. Whirlpool NEVER mentioned that the washer was recalled for the very same problem. I called them back with the recall information, and they politely sent someone out to rebuild the washer. Less than a year later it is no longer working, again. I went online first this time, to check for further recalls and complaints about the current problem (faulty control panel). I found many complaints about the same problem--even a reference to a class action law suit. Whirlpool said they were unaware of the problem, didnt have many complaints, and are unwilling to help. I asked for a supervisor, Benjamin, and he said there was NO means by which I could further escalate my complaint.

Since May 3, 2016, five servicemen have failed to repair my Whirlpool refrigerator (WRF560SEYM), which is less than 2 yrs old. One trainee from A&E Factory Service had the nerve to reinstall broken parts. I have been completely without refrigeration for the past 48 hrs only to learn that the repairman scheduled for tomorrow has been cancelled because AIG warranty has not approved his visit. Further investigation reveals that the parts were never ordered, pending approval from AIG. Whirlpool cant help me because AIG has not declared the appliance unfixable. Hhgregg cannot help. I have spent countless hours on the phone on hold & wasted hundreds of dollars on spoiled food. Dont trust Whirlpool. Theyre not the company they once were. Their warranties arent worth the paper theyre printed on. Buyer beware!

Whirlpool dishwasher failed after 16 months. It leaks continuously. they sent a service provider 5 days later out to fix it, then said there would be a $129 fee for coming (this was never mentioned at time of appointment), and the total repair cost would be $208. I wasted a day waiting for repair person to come, I declined the repair due to the cost. I called customer service later, during office hours, and I received the poorest level of customer service I have ever experienced. Whirlpool will no longer receive support from the our family. This machine cost over $500, and a ruined rug. Whirlpool wasted our time, and a day from work. We will never purchase Whirlpool appliances moving forward, due to this product and customer service experience.

I have had too many problems with the thermocouple beginning about two years after I purchased the water heater in 2003. Whirlpool keeps replacing the thermocouple, but I have to pay for the plumber to come out and repair the unit. This runs me about $180 each time. The thermocouple has burned out three times since September of this year. The plumber didnt charge me anything the second time it went out. But it went out for the 3rd time today and he recommended that I replace the unit. Of course, it is out of warranty and Whirlpool was happy to tell me that I could purchase a new thermocouple at my own expense from them. I have paid for this water heater three times over with repairs. Whirlpool knows that there is a defect with the design of the water heater. There is no way that a regular consumer can get inside the water heater to clean it. I will never purchase any Whirlpool products ever! I advise anyone reading this to follow suit.

As long as Whirlpool continues to use JB Hunt for delivery and installation service of their products, I would stay away from ordering. JB Hunt visited my home 3 times, and each time left with the dishwasher as they arrived without the appropriate tools to perform a basic installation. Whirlpool also sent 2 damaged dishwashers that could not be installed. Buyer beware.

Cabrio is our washer and dryer. Dryer had no issues in the last 7 years. Washer constantly throw UL or unbalanced error and stops. Rearranging clothes only works for another few minutes. First time under warranty, tech came and fixed it. Second time without warranty, I cleared some loose socks between the tub. Third time same problem. YouTube suggested to change the springs on four corners that hold the tub. $25 and problem fixed. Basically, if you are not an informed consumer you are screwed for $$ silly stuff.

Leaks water on bottom. Door seal dont go far to under door, is from manufacturing defect, is water overflow or is something else. Dishes washer is about 10 years older. Very real disappointed and wont buy this brand again on dishwashers.

On 02/25/13 we purchased a Whirlpool Gold Series side by side (French door) refrigerator with an ice maker at the cost of $1,850.00. In April of 2014 the ice maker stopped working and the freezer at the bottom would not freeze food. Luckily for us it was still under warranty and was repaired. At the time of the repair, the repairman (associated with HHGregg) told us that the refrigerator should have been replaced since the cost of the repair was more than the fridge itself. Now July 20th, 2015, the same issue has surfaced. Again the ice maker will not work and the freezer wont freeze. I would not recommend this product or if you do pay the extended warranty.

We purchased this washer (Whirlpool Cambrio #WTW8000BWO) in December of 2014. It is now 3 1/2 years old and while the washer worked great til just recently, we now have to purchase a different one because this one will cost too much to repair. We did not get the extended warranty. I have since read that the Cambrio has had a lot of problems. Always check the long term owners and what they have to say about the item, would never have purchased this washer had I known what the problems were and that they even were having them they should have taken it off the market til they got the situation fixed.

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!

We purchased the unit in March, by April it wasnt cooling. In June it shut down. In July after 8 tech appointments and repairs. Whirlpool finally said they would refund my purchase and I should see the money in about three weeks. That would be about a week longer than the refrigerator worked. I dont have the money to just get another one so I guess the family will be without a refrigerator for another month. That means shopping every day for perishable for a family of 10. I would not recommend another Whirlpool product. This is no joke, every time I called them one of the first things asked was Did you get the extended warranty? Why would they ask, sounds as if they dont trust their own product either. This unit was purchase online through Sears.com. Purchase price was $2299.99. Order placed on March 4, 2017.

Within a few months after I purchased my gas hotwater heater, I started having problems with it not wanting to stay lit. It was purchased in 2004. I see that this is an ongoing thing with Whirlpool. Every time I would call them, they would give me stupid answers on what it could be. One lady got hateful with me. I have replaced every part several times and Im having problems. About every two to three months, Im replacing thermal couple. As of right now, Ive been without hot water for eight days. I called and he told me about a trip button that is in the little white thing that has wires going to the thermal couple. I push in on it and then tried to start my heater and it worked. They have never offered to replace it or even give me a discount on a new one. No one should be having so much trouble out of your hotwater tank. This is not normal. These are defective and should be recalled. This company is ripping the consumers off and we need to stick together on this and do something about it. Im afraid to buy another heater because I can see that the new ones are still junk. What do you do?

I bought my fridge 6 years ago. 13 months after purchase I had to replace the compressor. Last month I had to replace the water drip pan. Now the fridge is knocking and hissing again and warm inside. Compressor needs to be replaced. I contacted Whirlpool and they said 6 years is old for an appliance. Seriously!?? What about 13 months when the compressor went? They obviously dont stand behind their products. They are unable to admit I got a dud. Im so disappointed and frustrated. Stay clear!!!

We did our research and wanted to buy a new washer and dryer with a trusted brand that would last. Our previous washer and dryer (different brand) lasted almost 20 years. Our new Whirlpool Duet HE Front Load washer only lasted about 2 years. The washer started making a terribly loud noise when spinning. We had a repair guy come out to evaluate the problem and provide an estimate for repairs. He said the drum, bearings, and truing was all one unit and the repairs would cost more than the washer. The factory warranty is only a year. BIG disappointment in Whirlpool.

I purchased a lot of Whirlpool appliances -- washer/dryer, dishwasher, microwave, and now a Whirlpool stainless steel refrigerator. This was approximately the end of 2014. Not long after I purchased the refrigerator, the front started with small rust stains. I notified Whirlpool and all they said was call Scratch-b-gone in California. My refrigerator should have been under warranty. They offered no other help. I live-chatted this morning and they say the same thing -- call another company. You are now out of service. Im so very disappointed in Whirlpool and will definitely rethink purchasing another Whirlpool appliance. My other stainless steel appliances are not having a rust problem -- just the refrigerator. I havent tried the Scratch-b-gone yet because on their website they say that a lot of Whirlpool products have a coating on them. VERY, VERY unhappy with Whirlpool and their customer service...

I have Whirlpool 25 in. Side by side. I love the space freezer size is bigger than the old one I had. Makes ice as it should. Overall solid appliance that I trust. I purchased this refrigerator a year ago after research.

The shelves in the newer units are plastic not glass with metal and they rip/break holding heavy contains like gallons of milk, and they are more expensive to replace. I just wish they would go back to building things like in the old days. My last refrigerator lasted 20 years. Ive had this one a year paid twice the price and already had to replace shelves and trays for it..

I had a perfectly good Kenmore range, but I didnt like the color. I purchased a Whirlpool 30-inch gas range at Lowes. I had problems immediately! The repairmen were at my house 6 times within the first year. My warranty expired and they wanted me to pay for an extended warranty. I refused to pay any more for this piece of junk! I fought with Whirlpool and demanded they either replace the range or reimburse me the full cost. They finally agreed, after many heated conversations, to replace or reimburse me as long as I promised not to purchase a Whirlpool product again. What kind of company would say that? A company that knows their product is defective and has poor customer service. I opted to take the new range that they promised wouldnt have the same problems. It is having the same issues as the original one. It shuts off in the middle of cooking and it is infuriating to say the least. I can promise Whirlpool I will never purchase a product from them ever again!

The refrigerator has worked OK except for occasional freezing towards the back. However the vegetable bins have both broken starting with various parts of the handles in front. We eventually replaced them. A brand new one arrive already broken. Same cheap brittle plastic. No alternative available. The company denies any problems or complaints about the bins. Feels like a small profit center for them.

The board manufacturer number W10312659 went out. They replaced the board. The oven was 6 months old, luckily was still under warranty. We didnt purchase a extended one because mostly it had a good name and brand. Well after a year and a half the board went out again. It gives error code H5P which there is no error H5P. So the boards out. It is very costly and thats with you doing your own service. Never will I buy another Whirlpool stove.

My side-by-side refrigerator leaks water. I find water on the floor but we cant find the source. When I called Whirlpool, they stated its not under warranty, but we can schedule a repair appointment, I declined. Im still looking for the leak. Its intermittent, sometimes I dont see water for a while. The last fridge we had, we had to get rid of it because the sides and front got too hot to the touch. I was afraid it would cause a fire.

November 4, 2017 we purchased a 2018 Tiffin RV with a Whirlpool 3-door refrigerator/freezer. We did not use the RV refrigerator until our first trip to Florida January 2018. Immediate problems with the freezer icing up on freezer door and icing up in the top 2 shelves of refrigerator. Milk, fruit, even cheese froze in the top of the refrigerator. Bottom freezer door froze so bad I had to yank on the drawer very hard to even get it open & chunks of ice would fall off the door on the floor outside once it opened. Called Whirlpool warranty service phone number two times 2/16/2018. I wont go into all the details but we were on hold for a 90 minutes and were transferred 7 times by the automated system. Talked to one person, Lindsey, who immediately transferred me again to RV Dept. No one ever answered. System kept saying, Please wait. Then just disconnected and another recording came on saying to call back. We did not after this fiasco! February 19, 2018 we called Tiffin MH & told them about the NO CUSTOMER SERVICE from Whirlpool. They told us to call Sears in Sebring, FL. We did. If we wanted Whirlpool service to bring the motorhome to them & the warranty only covered parts NOT labor or service calls. They did not want to work on it. March 13, 2018 We went to Tiffin MH Service in Red Bay, AL. Earl called Whirlpool tech, Steve, & tried to explain the problem. Steve told him he did not talk on speaker phone & told him very hatefully to put him on the private line. Steve just very angrily insisting that Earl had him on speaker phone. I do not understand Whirlpools Steve issue with being on speaker phone? Finally Earl got him to listen to our refrigerator problems as he stood there at the refrigerator going through each issue step-by-step. Steve said to put silicon in the seal & that Whirlpool WOULD NOT replace a 3 month old refrigerator that actually had only been used 2 months. We found out later Tiffin is going to replace the refrigerator.

I purchased this machine in April and already, the right leg is rusted and the under seam of machine is rusted. I have throw rug under it and where the leg is, there is rust on the rug. I called service from Whirlpool and 2 servicemen came out. The first one told me I was loading it wrong and the water was splashing over the inside tub to rust the leg and I asked, So why is the seam under the machine rusted? No answer. The second one came out and told me he could not find anything wrong with the machine and doesnt know why it is rusting, but he never gave me a paper to sign off on. He also said that maybe it was rusted when it was delivered. Not!!! Then I call P.C. Richard in Watchung, NJ where I bought the machine at and told them about the problem. They sent a serviceman out and he said that the bleach condensation is causing the rust, its known fact that this machine has this problem. He said that the water does not run through the dispenser but there is a model that does. I want a credit on this machine and get the upgraded one. It states on the machine that I can use bleach but it doesnt say it will cause rusting. I want you to tell me how a 9-month-old machine is rusted on one leg and the seam underneath is also rusted!!!! I had a machine for 10 years and it wasnt rusted. I am very unhappy with this product and with the customer service of Whirlpool. This is my first Whirlpool washer and I would not recommend this washer to anyone. I paid $600.00 for this washer and it should not be rusting.

I purchased an HIE washer one year ago this month. I have never been happy with the cleanliness of the clothes when they came out of the wash. The only way to get them moderately clean is to wash a few items at a time and even then the whites, especially socks, seem dingy. I noticed the new Whirlpool washers now have an extra setting to add more water to the machine, so the executives have realized there is a problem with the original model.I think Whirlpool should give all customers who previously purchased the models without this feature a trade-in option to get the newer model that fills with more water or for another model with the full spindle that has worked well for so many years. I have been very unhappy with the performance of this washer and would only hope the executives would do something to resolve this problem and satisfy previous customers.

I just replaced our Whirlpool Accubake Double Wall oven, model RBD305PDS14, because it fried the control panel after being put on self clean. This was the second time this has happened and I have probably only used the self clean feature three times since we purchased the oven. Im not a specialist in defective product design, but having a control panel burn up two out of three times when the self clean is used suggests a significant problem. I refused to pay to have it replaced again and obviously did not replace it with another Whirlpool product or any other brand associated with the company. I see that this problem has a long history dating back quite a few years with Whirlpool doing little or nothing to resolve the issue. (They just deny any knowledge about any defect in the design.) Fool me once, shame on you! Fool me twice shame on me!

I bought a full kitchen appliance package 3 years ago, the gas range Clock LED started cutting off the line at the top of the numbers... when the range was about 1 1/2 old... Now 3 years later the range doesnt hold its oven temperature, the cost to fix it is $230 more than what I paid for the range. Whirlpool is unwilling to stand behind their product or provide a replacement part for a reasonable price. So now I will be buying a brand new range and the 3 year old Whirlpool will be taken to the dump. I will never buy a whirlpool appliance again. I thought Whirlpool was a good brand and a reputable company until now. Please beware when buying appliances, whirlpool is not reliable or reputable.

My stove has met all my baking and cooking needs. Love the self cleaning oven and I mean it does clean every bit. Always bakes at right temperature. I love it. All my pies and cakes come out perfect and the look of it is just pretty and matches my kitchen.