Bought this model from Bad Boy in 2006 and just after the warranty ended the problems began. We kept getting the F1 error code so with a little internet research we found it was a known problem with Whirlpool. I contacted them and was told they knew nothing about this issue being nationwide, however I emailed them copies of the complaints and responses. They sent out a technician who had to replace the motherboard free of charge. Next issue was a loud noise coming from washer sounding like a jet plane taking off. Hubby ripped machine apart to find the bearings blown apart and in tiny pieces. We ordered new ones and also found that when the new ones arrived they came with a tube of grease and a sealer to use so water would not get in later and cause more problems. Funny there was no sealer on the original bearings.Next the lid lock finally failed, ordered a new one but did NOT install it back into the machine, now it sits beside the machine. In case it fails again we will have total access to the laundry this time. Finally the UL error code keeps coming up. I refuse to put any more money into this machine again so I am allowing hubby to fix it if he chooses, whichever way he wants as long as no money is involved. So right now we have bungee cords holding the suspension rods tight to help with the uneven load code coming up all the time. Personal thoughts - DO NOT BUY WHIRLPOOL washer/dryers. They are crap and the company just does not care and they try to lie their way out of repairs if people have not done their homework.

Ours is a glass top & has 2 dual burners & we are very pleased with that feature. The oven however takes quite long to preheat & the alert sounds are so weak you can barely hear them. It was a rapid purchase on a sale item. I wish we had shopped a bit more.

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.

Whirlpool serviceman came out to see why our brand new dishwasher didnt dry the dishes and left pools of water on glass bottoms. Repairman said all the new dishwashers are like this. The heating elements do not heat hot enough so that the machine gets a higher efficiency rating. He said the solution is to use the dishwasher during the day and at the end of the cycle, open the door so the dishes air dry. My previous 24 year old GE dishwasher did a great job of drying the dishes even when we didnt use the heated dry cycle! The only reason we had to buy a new dishwasher is because we bought a new house. I am very disgusted with the Whirlpool dishwasher. Might as well do dishes by hand.

The Worst experience with Gold Series Mod WRF 757SDEM01. Purchased from Best Buy June 2016. $2215.00. Within 6 months The interior light began going dark within 6 months. Our very reputable warranty repair service ordered a part that did not repair it. Was only temporary. They did figure out that the circuit board was bad and promptly took care of our problem. Next I kept noticing water appearing on our wood flooring. Let it go because it only appeared sporadically. Called Whirlpool only to find out they switched to a warranty repair service that was inept and inexperienced. Said he could fix it. Blamed it on a freeze-over so I let floor dry up then re-started and refilled. Thought he did fix it cause it made sense. When reassembling he broke to upper freezer try glide. Then 3-4 weeks later I notice one morning water again on my wood floor. The dripping had been running beneath the wood slats and had seeped up through the joints. Now the flooring wood has swollen and will need to be replaced because of this. This is the second time I had to unload all food and store at neighbors and give away. Extremely poor engineering designs as each time the ice dispenser is used, nothing prevents ice from flying out onto the floor ever since day one. Same with water. The release does not shut down to prevent water or ice from pouring out onto the floor when removing any size cup. The refridge doors must both be opened to use the lower level drawer. Loses much cooling with having to always open both. Next, weve come home MANY times with the left refridge door partially open because of the difficulty of the mechanism to secure at closing. This happens to us 5 times a week for three years-honestly!. This was the only refridge we could find that would fit our opening in a 20-yr-old home. The fridge is so heavy one man cant pull it out of its opening. Only 2 very small wheels in front and skids in rear stick due to weight. Weve confirmed this is not a spigot leak from the ice maker. Finally (but probably not) the ice container allow much air in because of having to open the left door that your ice is always melted together plus it too small for a family of two and ice must be purchased when entertaining. And to top it off, the human that took the warranty call this time is foreign and my wife could not get them to get our last name spelled correctly nor the phone number correct after constantly repeating it. This unit and model is an absolute lemon. Im going out today to find another unnecessary $2500.00 to buy another.

This is a defect due to the removal of the dispenser heater being removed. The insulation is inadequate behind the ice/water dispenser (@ 3 feet from the bottom of the door.) Replaced the line, thawed it out multiple times, added extra line under the fridge in the coils to try and warm up the water in the line between the 90 degree elbow connector and the dispenser... no luck. Since all the manufacturers models are being assembled in Mexico, using the same designs, other models are have the same issue. GE is backing theirs with a replacement freezer door. Well see if Whirlpool backs theirs. This whirlpool Gold is @ 3 years old and the issue started around a year ago.

I lodged a complaint of Microwave problem on 05/11/2011, and up to this date (18/11/2011), I am still waiting for the problem to be solved. I have a 1 year old baby. We cook food for him in it. Due to the microwave not working, he is suffering.

This Whirlpool Cabrio washing machine just does not do the job. It smells inside and does not get clothes clean, just normal everyday laundry. I usually have to put them through twice. It is supposed to be a water save, but I dont think it uses enough. I use minimal he detergent, yet you can see detergent residue on the clothes after they are washed, I think because there is not enough water running through to rinse clothes very well.

This is not a new washer (Whirlpool Cabrio INTW6200VWO) and it works well BUT since we have owned it we have had rust at the bleach dispenser. I am seeing on the internet there are many complaints about this and there was a recall? But they have run out of replacement parts??? Never received any recall notice. We have online instructions on how to repair and have done this many times and the rust comes back. About a week ago we sanded, primed and enamel painted the area plus I have put NO BLEACH in the dispenser and the rust is coming back. I hate to replace a working machine but this rust can and will get on my clothing. Whirlpool was the absolutely best in the past but this one is a lemon.

I bought a whirlpool washer from Whirlpool on February 27, 2011. Since then, they have come out and repaired the washer for 5 times. They have even taken the whole motor out, and replaced it. The last time they came, they said I would have to pay for the next time. Now, it has broken again, and I have to pay for a washer repair that is less than a year old. We bought the Whirlpool washer at Sears, and neither Sears, nor Whirlpool will stick by their product. We cannot afford another new washer, and to pay for repairs is a stretch too. Is there anything you can do?

Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.

This is the worst washer ever. I purchased this washer (Whirlpool Cabrio Washer Top load) brand new in the box thinking it was a great price and a good deal. Worst choice ever. I have been so disappointed in this product. It is very noisy which is something I have learned to live with. It doesnt even get simple stains out. I have tried every load combination and change detergents and stain remover a couple of times. Most time I have to soak stains again and again and then wash several times and most times it simply doesnt clean clothes. It leaves detergent residue on dark clothes so of course I end up washing those again as well. The towels and sheets turn into mushrooms in the bottom of washer.

The burners were very crooked and the pans got burned out right away. They were covered under warranty but since then, they had the same problem with them with the new items. They had the light bulb stuck and couldnt get it out, they came under warranty and now a new light bulb wont work in it. The control top indicator light didnt work so I had that fixed under the warranty, but now it has the same problem and I cant afford to get it fixed and it could be a real safety issue.When it was under warranty, I called about the brown in between the oven door and they said it was cosmetic. It gets worse every time we use the self-cleaning oven like the seal isnt tight. The outside of the door gets brown also when using the self-cleaning oven. We thought we would have this range for a long time as we had a Whirlpool range before which lasted 20 years. I will never buy a Whirlpool product again and we have had a lot of them. e cant afford to buy a new one so we are stuck with this one with all its problems. Whirlpool just gives you the runaround when you call. When they brought the range, the self-cleaning oven part wasnt even hooked up so they had to come back and fix it. I cant believe they dont have more recalls on these. I have only had this for 4 years.

I have been a dedicated Whirlpool customer for 50 years. I purchased my new, Cabrio washer and dryer in 2011. The dryer works fine. The washer does not. It ties everything in knots. Most everything comes out in one large, wrinkled lump. When washing sheets, it wraps the whole load in a soaking wet, fitted sheet bubble. You cannot wash one item by itself, because it will become unbalanced and shutdown. I will say that I havent had any repairs yet, but I have a feeling, its only a matter of time. I have decided to buy a new washer, but it will not be a Whirlpool.

I bought this fridge 2 years ago. I had multiple repairs already. Now the side panel makes noise when you shut the door. Repairman told me it is the foam separating from the side panel. There is nothing that can be done. I also have extended warranty.

I purchased this machine from Sears on 04/23/2016 and have had nothing but problems and issues with it. It is loud and makes different sounds every time I use it. It has overfilled and underfilled with water a few times, the machine shuts down while washing and I have had to restart the machine. Half the time the clothes come out covered in soap and I have to put them through another rinse cycle. My bedding always has to either go through a second rinse cycle due to being covered in soap or I have to rewash it because it is all packaged together in the fitted sheet and never got washed. During the spin cycle it sounds like it is getting ready launch into outer space and it vibrates excessively. On numerous occasions I have had to untie my clothes as they are tied in knots. There have been times that I had to put the clothes through another spin cycle because the clothes contained too much water. The final straw was last week (03/27/2019). I washed my sheets and they came out bundled up in the fitted sheet full of soap stains and I had to rewash them. When the sheets were done I put the comforter in the wash and started to clean the house. When I went into the laundry room the washer was not running but the wash light was on so I opened the lid and felt the comforter and found it to be dry. I closed the lid and pushed the start button. After a few seconds the washer shifted to rinse without even washing the comforter. When the washer stopped running and the ready light came on I removed the comforter, unplugged the machine, shut off the water, disconnected the water hoses, placed the machine on a dolly and took it to my scrap pile. I could not find any Whirlpool washers with any good reviews so I purchased a Speed Queen with a 5 year parts and labor warranty.

We purchased a gas range (Whirlpool AccuBake model # mfgxfg361lvt1 serial ry1810956) a few years ago and have been very unhappy with the gray grids that it came with. We wrote to you about how we should clean them and you recommended heavy-duty degreaser, pin31552a and gas grate & grill cleaner, pin3167a, which we purchased. Neither worked, even with heavy elbow grease. We are very upset. We have purchased Whirlpool products all of our life and would like an answer or some type of explanation. If possible, can we get the grids in black? We try our best to keep these things clean and this is a very bad patten.

Whirlpool gas range convection oven - I have only had this range for 2 weeks. Manual is sketchy to say the least. Purchased from LOWES - salesman were not well-informed. I have had to do a chat to find out information. Range looks great but performs poorly. Takes a while to heat anything even on high and on large burners. Grates are too heavy. I am sorry I did not see the editor review before I purchased. I have not used the convection so I cannot speak to this but my choices were limited when I purchased and I did not want a convection oven and other ranges would not purposeful for my use.

2012 1st year water dispenser stuck, would not stop pouring water until I shut water valve off behind refrigerator. Replaced switch under warranty. 1st year bottom mount freezer stopped working, replaced condenser under warranty. Handle coming off freezer door not replaced. Today Nov 5th past warranty date Oct. 21st 2012. There is ice buildup in bottom of freezer due to a duckbill valve that I just found out about... This is junk and I already replaced the washing machine. Now I am going to replace this fridge if I have to have money to fix this out of pocket. Dont buy whirlpool and i think they make the same thing under other brands like Kitchenaid. My fridge was registered with whirlpool and no one contacted me from whirlpool about the problem they were aware of, to tell me that the valve is free and labor was free for first two years. Now only part is free. What a rip off. My appliances were part of the purchase price of a new home from a developer.

Bought a water heater on May 5th for 539.00 and was unable to get hot water all the time. After many days and dealing with Lowes which did not help and Whirlpool, I discovered that the unit I bought had no dip tube to bring the cold water to the bottom to be heated and thus provide hot water to the hot water outlet on the heater to the rest of the house. People at Lowes had no dip tubes and really have no knowledge of what is going on as the people at Whirlpool whom I called.

I am really disappointed because I purchased the refrigerator and now the dispenser display assembly is not working and the company does not have the replacement part to fix it. So now do I have to buy a new one???

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

Do not buy Whirlpool appliances! Save yourself the trouble. I have a Whirlpool free-standing gas range that I bought when I purchased my house in June 2008. Just the other day, the oven stopped working. When I went to turn the oven on, I can hear a clicking sound but the burners in the oven do not ignite. I called Whirlpool and they offered to send someone out to fix the problem. By the time someone comes out and charges me for parts, labor, etc, I will probably have paid half of what I paid for the range when it was new! I also had the same thing happen with a Frigidaire refrigerator last year! The bottom line is that brand name appliances are not built the way they used to be. I am actually looking at buying a Samsung or some other model and try my chances with them!

Whirlpool Cabrio Washing Machine F1 code - We have had this washing machine for over 6 years now, and ever since our 3 year warranty time was up, the washing machine will only stop, and display the F1 code as soon as the wash cycle has completed, with 23 minutes left. To start off, with this problem, it is causing me more water, and electricity that should not have to be wasted if the machine worked properly. I called the place where I got the machine, and was told to give Whirlpool a call. I did this, and was told that there was nothing that could be done, and if I would like to schedule an appointment for a tech to come out and work on it, they could do that. YES, I would have to pay for it. Needless to say, the washer has been doing this for over 6 years, and if there is a way to get it fixed WITHOUT having to pay for the repairs, that would be wonderful.

My Whirlpool microwave has been serving me for over 20 years. Never a problem. It performs well at all settings. Size is convenient for mounting over range. I recommend highly because of reliability and performance.

Purchased a Whirlpool side-by-side refrigerator model #ED5KVEXVB07 in July 2012 from Sears for about $1000. Unit quit cooling late Dec 2014. I did not purchase the extended warranty, so the Whirlpool 1 year warranty was all I had. The repair technician (local company, not from Whirlpool directly) told me that the compressor had seized up, and the repair would be at least $300. I thought Id call Whirlpool just to see if theyd be willing to do anything for me. Long story short: No. I told the person on the phone: “I will never buy another Whirlpool appliance.” She said: “Im very sorry about that.” After I hung up, I thought: If Whirlpool was really sorry, theyd stand behind their products for a part that should not fail after only 2.5 years.

All of sudden, this expensive microwave stopped heating. Called whirlpool, they said they will charge $300 to fix it and $540 to replace. So much after paying new piece of garbage in 2-3 years.

What a piece of expensive junk! Do not buy it, does not clean clothes well, lid broke, lock broke, now it just wont start. Parts are super expensive. Next one I buy will be a basic washer, forget all the bells and whistles!!

Bought the top of the line Whirlpool Cabrio washer and dryer. Washing machine lasted 3 years. Took forever to do a load and would not be clean after taking an hour to wash. The dryer is still going, but would not surprise me if it died any day. Do not buy.

We just recently remodelled our kitchen and decided to buy a Whirlpool Range. Big mistake. First off, the range was advertised as a built in but it ended up looking like a slide in. We were disappointed but decided it was ok as long as the range performed fine. However, within 6 months of buying it, the oven fan broke and the oven became unusable. I used it only 2 - 3 times before it gave up. Extremely disappointed. Our old oven was sturdier and lasted many years and was in a very good condition when we gave it away. Extremely disappointed since we paid a lot for it.

There seemed to be an issue with the Whirlpool Cabrio Washer Pump. If a button comes off from your clothing or snap, etc., it gets trapped in the washer pump, causing it to crack and leak. Whirlpool on warranty only allows for one free change and anything after that costs $300.00. This is going to be the third time we are having problems with this and it is becoming, economically, a struggle for us. We have checked every button and snap to make sure they are fastened tightly, as well as any other type of items that may fall off in the wash and become trapped in the pump causing it to crack and leak. These pumps were poorly made and Whirlpool needs to be more aware of this problem rather than telling the customer that they are not aware of the situation.

I had a Whirlpool washer that was 31 years old so when the motor went out I bought a Whilpool Cabrio. I HATE it!!! First, it takes at least an hour for 1 small load to finish. Then the clothes are not even clean and rinsed all the way. Dry patches on clothes and where the soap did reach the clothes there is white soap scum all over. I tried using the extra rinse function and still soap everywhere. Im hardly using any soap to begin with. I have to wash some things twice to get the soap off. Thought I was doing good by buying HE. What a waste of money. I cant wait til it breaks which should be soon according to all the previous comments. I have only had it 4 weeks. Dont buy this machine!

I purchased this washer model WTW4950XW0 new. Within 6 months, it stopped spinning and was repaired under warranty. The spin actuator was defective. Great. A few months later, it stopped spinning, repaired under warranty and the spin actuator was bad. A few months later it stopped spinning, repaired under warranty, and the actuator was bad. Great. Another few months it stopped spinning again. This time, Whirlpool sent someone to repair it, another bad spin actuator. This time we had to pay for the part. So now that we are completely on our own, it stopped spinning yet again. Let me guess. The spin actuator is bad!!! Incredible. What a piece of crap. This washer was never used heavily.

I just bought a new dishwasher because my 5-year-old one went out, model number DU1145XTPBA. After pulling the old one out, I took the motor out and lo and behold, what did I find but bad bearings. The motor was fine, just the bearings were rusted out and were jamming the motor so that it wouldnt move. The price of a new motor, $149.00. Well thats a bit much for something that only lasts 5 years. I went on eBay and found them for $70 to $170.00. So if you have a problem where your dish wont wash at all but fills up with water, it may be nothing more than cheap bearings in the motor. If I, myself, were this companys CEO i would really consider changing companies that they have making these motors or at least the bearings. Just wanted you to know that this is the only problem I have had with this one and Im going to replace the motor now that I know what it is. Thank you Whirlpool for a day spending repairing and replacing one of your dishwashers. I learned a lot.

I bought a Duet front load washer and dryer set in January 2009 from our local Lowes. Spin cycle noise progressively got louder over time to the point we contacted our locally owned service company to check it out in June 2011. Cause is defective shell and spin tub, total repair cost $750. This was about the original cost of the washer! I contacted Whirlpool via e-mail (wait time via their phone is outrageous), they wont do anything. Out of warranty. Up until now, Whirlpool has had a good name with me. Not anymore. I will never buy anything Whirlpool manufactured ever again. (Maytag, Kenmore, maybe more brands.)American companys insensitivity such as this is what gives some of American industry a bad name and drives consumers away to quality foreign brands made in Europe: German, Swiss, Italian, Swedish,etc.Im going to take a hard look at Bosch washers to replace this Whirlpool piece of junk.

I purchased a Whirlpool electric water heater in August of 2008. The unit had a 12-year warranty on the tank. On January 21, 2012, I discovered that the water heater sprung a leak somewhere in the tank shell; it’s not the pressure relief valve, thermostat or anode port. The tank was never abused and operated well within its design limits. Not sure what caused it to start leaking into the catch pan and out onto my laundry room floor.I purchased the tank at Lowes and went for the longest tank warranty to reduce replacement intervals. I sent Whirlpool an email on 1/22/2012 explaining my problem and I referenced this site. The next day 1/23/2012 I receive a call from Whirlpool (Chris) asking me about my problem. I explained again and they gave me an RMA number and told me to go to Lowe’s and they would replace my hot water heater. I went straight to Lowe’s customer service and within an hour I was on my way home with a brand new hot water heater. Thank you, Chris, Whirlpool and Lowe’s. I am very happy with my outcome on this issue.

This is my second Maytag French door refrigerator. 1st died after 5years. Bought the same again but bought an extended warranty. After 3 years, a month of service calls I still do not have a running refrigerator. Had to rent one from rent a center while Whirlpool sends more repairman. Try calling their customer service is where they got their name. They give you such a runaround they create a whirlpool. Product is junk.

I had the best experience when I purchased my washing machine and dryer. The personnel were professional and very pleasant. I am quite pleased with my washer and dryer. I have had a couple of minor problems but the warranty that I had on them was excellent.

Whirlpool’s water heater coupler. Our plumber came to our home and explained how there was a problem with our type of water heater from Whirlpool that had been sold from Lowe’s between 2000 and 2006. We purchased ours in 2004. I have the receipt. Our plumber stated the underneath screen was clear and in good shape. He also said they had other water heaters with the same type of problem and those companies had provided the new part free and free shipping due to the suit. Whirlpool has not. We have been without hot water for a couple of days and we are hoping to have the piece by tomorrow. Since this suit has already been dealt with, then how do I get my money back from Whirlpool for being dishonest with requiring me to pay? Do I need to file something? I have followed the links and I have been researching it and our model number and serial match the product that was found faulty.

The refrigerator has worked OK except for occasional freezing towards the back. However the vegetable bins have both broken starting with various parts of the handles in front. We eventually replaced them. A brand new one arrive already broken. Same cheap brittle plastic. No alternative available. The company denies any problems or complaints about the bins. Feels like a small profit center for them.

I purchased a Whirlpool water heater and after working fine for about 2 1/2 years, I began having problems with it staying lit. I dealt with troubleshooting beginning in January of 2012 and finally in March of 2012, I was sent some replacement parts. The unit worked fine through the summer and once the weather started getting cold in October of 2012, I began to have problems with the unit again. After a couple of months complaining and threatening to file a BBB complaint, I was sent all of the parts left to change on the water heater. And I was told after the parts were changed if the unit still did not work, that it was probably a venting issue and that I would be responsible for that issue and the unit was not defective. I received the parts on 12/04/12 and they were changed out the same day. Now the unit will light when I hold down the button to light it but once I let go, the pilot light goes out. At least before changing out the parts, the unit was able to be turned on and sometimes it would work and other times it didnt, but now it will not light at all. This is very frustrating because the unit is under warranty and Whirlpool has for an entire year fought me tooth and nail just to send me the parts for the unit, only for the unit to still not work. I have a family and it is discouraging to not know when you are going to have hot water, having to constantly fix the unit or to call Whirlpool to troubleshoot and finally for the unit to still not work after replacing the parts. It looks like I will not have any hot water at all now.

If you are in the market for a new washing machine, steer clear of the Whirlpool Cabrio (or any Whirlpool for that matter). We have had issues with ours from the beginning. We had Whirlpool techs come out and were continually unable to fix the issues. Eventually they told them that it was not broken, even though one tech told us it definitely was. After four service calls they just stopped sending out techs and told us too bad. Now after less than two years it is leaking from the bottom. Yeah, Whirlpool, theres no problem with it. Save yourself the potential headache and get something else. Anything else.

We bought a Roper refrigerator about seven years ago. Less than two months later two of the cheap plastic door shelves broke and we had to buy replacements at over $20 a piece. Since then weve had to replace one more. Tonight another one broke so well have to fork over another $20+ to replace this one. I checked the Whirlpool website and they have the exact same flimsy plastic shelves as the Roper. I will be in the market to purchase at least three refrigerators in the next two years and you can bet that they wont be either Roper or Whirlpool. My advice to anyone in the market for a refrigerator to steer clear of these two brands as their shelving is cheap and shoddy.

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.

I purchased an electric double oven range on 11/20/11, model # GGE388XS00 and serial # D02584385. Something is getting in between the glass on the bottom oven door and theres no way for me to clean it out. I feel it is an issue with the seals they have around the glass oven doors.Whirlpool says its common for that to happen. They say its condensation. But it doesnt look like condensation to me. Whirlpool says theres nothing they can do about it.I had this same issue with a Whirlpool microwave oven I had. I finally ditched the microwave and bought a new one, because after a while, it starts looking really nasty. I never complained about the microwave, but after buying a new oven and it starting to do the same thing, I thought Id better complain and see what they would do about it. Theyre not doing anything about it.

Had washer since 2016. Have NEVER washed a load where there was not a problem from washer dancing to having clothes come out without water ever touching them. Would NEVER recommend Whirlpool! Tried to contact Whirlpool website to register a rating & even their website is defective - could not get through after several attempts.

I am a senior who has not used the Whirlpool Range installed by the builder in 2007 very much. First of all, I did not like the way the covered jets hid the lighted jets when they were turned on low. Then about 8 months ago, I smelled gas and no one had used the range. I checked the knobs and one was turned slightly without any gas lit. I know that for years the companies were required to have push-in knob before you could turn them for safety reasons (especially children). These knobs barely push in before turning so that they can easily be accidentally brushed against and leak gas, which is exactly what happened to me again today. My daughter was visiting. Neither of us had used the range and when she left, I sat in my living room and smelled gas. I immediately checked the range and the small front jet was turned slightly on. The odor was so strong that I know it had to have been on for some time. Its been an hour and Im still airing out the house. I have used gas ranges for over fifty years and never had a problem such as this. Im thankful that I do not have issues with my sense of smell. Otherwise, I would not be sitting here writing this.

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

Updated on 02/13/2021: Company fails on customer service. My stove’s trim is rubbing off on my Whirlpool stove only 6 months old. No chemicals were ever used to clean the surface. This trim piece surrounds the controls and is not covered under warranty. An expensive cheaply made stove. Multiple attempts to have the piece replaced got nowhere. A letter sent to the head office was deferred back to customer service. Whirlpool has lost credibility and I will no longer buy their products.Original Review: So disappointed to find the paint finish coming off the trim on my 8 month old Whirlpool range. No harsh cleaning chemicals were used. Only mild dish soap and a microfiber towel. The trim, attached to the control panel on the front of the stove, is not actually stainless steel, but painted to look like stainless steel. Whirlpool warranty doesnt cover esthetics and refused to replace the trim, stating replacement would include the entire control panel and it is not covered under warranty. So be prepared to have your new expensive stove look old in a matter of months.

Oven was purchased new from Home Depot. Right off, the top black glass surface got scratched. Not sure how it happened. Seems to scratch easily. Then, the oven temperature for baking was found to not hold consistent. While pre-heating the oven for 350 F, the temperature goes up to 375 F, then well into the baking time, can drop to 100 degrees less (275 F). Oven feature is called accu bake. It ruined the baking and seems to be anything but.

Another reviewer complained about a knocking sound upon startup. My Brand New fridge has been doing that and I have just ignored it. Maybe I shouldnt. Compared to our original Beaumark fridge, the Whirlpool is VERY NOISY.. Since the actual workings seem fine, I am not complaining but rather quite concerned.Especially after reading the numerous Negative Reviews.

My low Budget rental property combinations oven stovetop could not handle it. 1st two of my stovetop burned out. 2nd the knobs broke just from turning the stove off and on. 3rd the oven only works with the oven timer. 4th the was only two years old when it fell apart. I dont recommend this low budget stove.

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

There is a chronic and well-known problem with recent French door, bottom freezer refrigerators sold by Whirlpool, including the the brand names KitchenAid, Jenn-Air, Maytag, and Amana. The problem is caused when the defrost drain freezes, preventing defrosted water from reaching the evaporation pan. After enough water builds up, it overflows along the front of the refrigerator. In my particular case, we have wood floors and they were ruined by the water. After doing some investigation on the internet, I have learned that this problem affected approximately 1,500 model numbers sold under these names. These model numbers are listed in a Technical Service Pointer issued by Whirlpool.In August 2013, after experiencing several years of problems with these units, Whirlpool issued a Technical Service Pointer W10632338, advising service technicians that a new P Trap drain tube kit was now available, and suggesting that the defective duck bill check valve should be replaced by this new part. The problem for years had been that the rubber duck bill check valve would, over time, become sticky (or tacky) and would then not open - causing water to build up above it. Eventually, the water would freeze and since newly defrosted water could no longer escape, it would build up and eventually overflow.From what Ive seen online, plus a conversation with the Sears technician who come out to diagnose and repair my leak, I am convinced there are many thousands of customers who have experienced this problem. Because it takes a while for the rubber check valve to become sticky and no longer open, it is not uncommon for the problem to not appear until after the standard one-year warranty has expired. From reports, Whirlpool has sometimes acknowledged the problem and effected repair of refrigerators no longer under warranty.But what about those customers, like me, who have experienced water damage to floors and cabinets? Shouldnt Whirlpool be liable for those repairs, too? Id be interested to know if anyone knows of plans for a class action lawsuit.

My front load washer doesn’t get my clothes clean. I have to rinse twice and still there is soap in my towels and they smell bad. I’ve followed all the tips without much luck. Now I use only Oxyclean and rinse with 1/4-1/8 c vinegar. The machine doesn’t pump all of the water out of the machine either. To me it is low-efficiency!

Cabrio he washer wtw6400sw2 - I bought this washer about 6 years ago at the time we paid around $900. Now my bearings went bad and the repair person told me it would cost around $300 to $400 to replace the bearings and seal and shaft but that I should call Whirlpool and see if they could replace the part or give me some discount cause it is becoming an issue with all the Cabrio washers. So I called and spoke with a so called manager - as far as I know it could of been a cleaning person there. She told me that she could not do nothing about the issue. So if a lawyer would be nice to help me and the rest of the world that are having all these issues to file a suit against Whirlpool Corp.

The dishwasher is noisy and the latch which holds the soap, at times sticks. When we think it is done and ready to unload we need to run it again because the latch that holds the soap DID NOT open. Not good.

Cabrio is our washer and dryer. Dryer had no issues in the last 7 years. Washer constantly throw UL or unbalanced error and stops. Rearranging clothes only works for another few minutes. First time under warranty, tech came and fixed it. Second time without warranty, I cleared some loose socks between the tub. Third time same problem. YouTube suggested to change the springs on four corners that hold the tub. $25 and problem fixed. Basically, if you are not an informed consumer you are screwed for $$ silly stuff.

We moved into our house about 5 years ago. We didnt know how old the heater was so 2 years after moving in, we replaced it with a Whirlpool Electric Water Heater. (2009) Last August, (2 1/2 years after installation) we found our carpet soaked in the room adjacent to the water heater and discovered it had been leaking into my finished basement for who knows how long. We contacted Whirlpool and they said they would replace the heater but I had to pay for the install because it was over a year. Mind you I had just paid 300 bucks 2 1/2 years before to put that one in. So I paid another 300 bucks to have a plumber come out and install this one. I had extensive damage to my basement, rug, walls with mildew and possible mold from the water. I went through my homeowners insurance and had almost $5000.00 worth of damage.So about a week ago my husband calls me downstairs and guess what, my brand new rug that I had replaced 11 months ago due to a leaking Whirlpool Water Heater was soaked again. This heater, 11 months old, leaked yet again!!! Needless to say Im beside myself, especially when I call Whirlpool and they will replace it, again, but who the hell wants to have damage to their finished basement every year??? When I called and asked them to pay for the damage this time because I cant possibly put another claim in with my insurance in less than a year for the same thing, they just say that they will have the labor charges dismissed as a courtesy. As a courtesy??? I said its been less than a year so they owe me the labor charges; she said no that it goes by the original warranty from 2009. What??? Thats utterly ridiculous and how is it possible that they can get away with this. That has to be against some state statue or law, to use the previous warranty on a defective product. So now Im left with about $2000.00 worth of damages this time to my brand new refinished basement all at the hands of Whirlpool. I had to get another one of their heaters because they wouldnt even give me the money for the heater so I could buy a different kind. I will NEVER buy a Whirlpool product again and Id advise to anyone who will listen to spend a little extra to avoid this hassle!

In 2099, I purchased a Whirlpool Gold from Lowes. It has never cleaned my dishes, especially the pots and pans. My dishes also have a powder coating on them after various cleaning cycles that I have tried. I have tried every detergent available.The repairman suggested a detergent, which I already tried. He told me that the dishwasher uses only 1.9 gallons of water in total. That confirmed what I thought the problem was, not enough water! It is a design problem that cannot be fixed. I have bought Whirlpool for years but not in the future.

I purchase a suite of Whirlpool Kitchen Appliances April 2017. My range is the slide in model. The knobs are on the front of the stove top. I 4 months in I saw that the paint behind the plastic panel where the knobs are was chipping. Also, the gasket in the oven had some loose threads so I finally decided to call the warranty. Whirlpool paid for the gasket to be replaced but Customer service said the chipping was cosmetic and that only covered for 30 days. I am so disappointed in this range and Whirlpool. My stove looks very used after 10 months. I followed the instructions on what to clean it with and how to clean so I know its not me. The paint chipping is crazy! How as consumers do we deal with this? This Range was a cost over $2000! and they give me touch-up paint!I purchased Whirlpool because I researched prior to purchasing my appliances. I thought I was buying Quality, this is not quality! At Christmas I had a pot of potatoes boil over and the element circle on the glass top cam off with cleaning. This too is not covered because its cosmetic. Ironically, my old glass top Whirlpool range did the same thing. That why I got a new one! I guess it still works. Who cares how it looks... RIGHT? Well, I WAS a good Whirlpool customer. Not anymore! Do not purchase Whirlpool glass top ranges unless you want it to look worn out after less than one year. I have tried to post pictures but this wont let me paste them!

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

I submitted a complaint several days ago about my 3-year old Whirlpool Duet washer not working and costing $550 to fix. I decided to just replace it so my husband unhooked it this morning. We were going to to try to sell it on Craigslist as is. I pulled out the laundry detergent compartment to clean it because I had filled it with detergent and fabric softener the other day. The smell that came from inside the washer where the detergent is dispensed was awful. I looked inside and it was completely filled with mold. I had periodically run the clean cycle with bleach but apparently this did nothing. I am writing this second review to warn people about this. I am going to just trash the washer now and I hope this has not affected our health in any way. For those of you who are thinking about purchasing this washer or one similar, I strongly urge you to stick with the plain old top loader. That is what I am going back to.

Started researching online about a week ago because my dryer was making an awful noise. Found out that the new idler pulley system the company used in my Whirlpool cabrio washer & dryer model (WED5500XW0) was so ineffective that they have since started replacing it with the old part #691366 they used to use. Also I am having a problem with my washer not spinning all of the water out of the clothes. Found out that this is a common problem with this model (WTW5500XW0).Had a certified repairman out to replace the dryer idler pulley system. He also calibrated the washer to see if that may help (it did not). The repairman said that some of the Whirlpool washers had been recalled and he had actually replaced some control panels and that seemed to work. He suggested that I contact Whirlpool. So I contacted Whirlpool, thinking that they obviously knew that there have been many problems with these machines (idler pulley part being discontinued & and recall on SOME models), and thought they would be more than willing to rectify this problem. Well think again! The two young ladies that I spoke with sounded like robots, Unfortunately, you are not within your 1 year manufacturers warranty so there would be nothing we could do at this time. Although I must tell you, the second young lady I spoke with did offer to sell me a new washer at a deep discounted price of $386 (which is only $86 more than fixing the washer). I think everyone who has a problem should contact Whirlpool and express this dissatisfaction. And if you are shopping for a washer and dryer, stay away from Whirlpool because their customer service is disheartening.

I purchased all new Whirlpool appliances for my kitchen from Lowes about 5 years ago. The dishwasher was leaking water onto my hardwood floors after about a year. I figured out that the seal was pulling away on the lower left corner. I fixed that myself. It cleaned pretty well for about 3 years. Now its not cleaning at all. I took the lower spray arm off to try to clean it. Almost all of the holes are clogged with debris. (I clean the filter at least once a week.) I went ahead and ordered a new sprayer arm, maybe that will help.As for the rest of the appliances... After about 6 months, the freezer started filling up with water that then froze on the bottom and allowed water to pour onto the floor. The microwave handled broke after about a month. (They did send me a replacement handle.) The knobs on the stove are starting to peel. One of the knobs wont stay on, so I keep it in the drawer next to the stove. Overall, I am very disappointed in all of the appliances. This will be the last time I buy Whirlpool.

I bought a whirlpool water heater at Lowes 4 months ago, and it has stopped working. I called the customer service number and was treated so unjust. I told them that I had just had it looked at by a plumber and he said that the water heater needed to be replaced, I told the whirlpool represented if what the plumber had just advise me. So I asked them if they could just replace it, the customer service representative told me I had to call another number to have their service people look at it and that wasnt for another 10 days. At which time I asked the representative what was I to do without hot water for 10 days. She told me that they could only schedule it that way. So Im here to tell you all please please please dont ever Buy anything from whirlpool because they will not back it up! I on the other hand just lost $500 and went out and bought a Rheem water heater instead.

I just purchased a top load wtw5000dw01. There have not been any changes to this revised model except the lid only locks in the rinse/spin cycle now. If that even helps anybody. It still has the noisy agitator which is the thing I hate most. Whirlpool engineers better go back to the drawing board and redesign their washers. Whats this country come to when you spend a pile of money on something that sounds like it is broken from brand new. I also had a washer that was 15 years old and never had noise issues or problems with it. Its just not Whirlpool that uses this so called new technology.

My husband and I purchased a Whirlpool French-door Refrigerator in Feb. 2014 from Best Buy. We did not purchase a warranty through them (BIG MISTAKE) because everything we heard about Whirlpool was positive, at least through friends and family. 1 year and 6 months later we have NO freezer and their warranty expires a year after purchase date! I called the company and they are no help at all! From all the comments I have read on here, there are few positive results! From now on I will be checking all reviews before I purchase a product again and WILL NEVER buy another whirlpool product again!

5 years and 11 months ago I bought a 50 gallon gas, Whirlpool hot water heater with a 6-year warranty from Lowes. The 2007 water heaters were on sale, so I paid $329 for it. Within 6 months, I replaced the gas valve, and a few months after that, the thermo-couple went out and I replace that. Each time I called Whirlpool and got return authorization numbers for the parts, I still ended up paying for the parts plus labor. A year after that, the igniter went out and I had that replaced. Last year (the day before Thanksgiving), the thermo-couple went out again and I had to have that replaced - and it cost me for the part plus the labor - even though I had a return authorization number. I also replaced the water line connections/hoses to the water heater at that time. The customer service rep for Whirlpool told me at that time if I had another problem with the water heater, they would replace it for free - and the warranty was good until Dec 31, 2013 (this year). NOTE: Every plumber that has come out to fix the water heater and replace the parts stated that they see a myriad of problems with Whirlpool water heaters. They said the parts like the thermo-couples, igniters, gas valves, etc are poorly built and they replace them all the time. On Christmas Eve 2013 (two days ago), the water heater started leaking from the top by the valves - and so much pressure had built up in the heater the new water hose connections burst, spewing water all over the heater closet. I called Whirlpool the day after Christmas (today). At first, they told me they would not replace the heater as it was not in warranty and then I told them what I was told by the service rep last year. She finally agreed that my heater is indeed under warranty and gave me a replacement authorization number but she told me my warranty did not cover labor. I called Lowes. At first, they told me I would have to remove the old hot water heater myself and bring it back to the store in order to get my replacement. I am a 59 year old woman and I take care of my brother, a disable veteran. Although I am in good shape and healthy, I dont have anyone to help me get the gas and water disconnected and help me lift it into my Suburban. The man at Lowes agreed to bring out the the replacement heater and pick up the old one at no charge, but I will still have to pay $299 plus the cost of new hoses to have it installed. By the time the replacement one is installed, I will have paid a little over $1200 for a $329 water heater. I could have installed a tankless one for that, but I cannot see spending that kind of money right after Christmas. If I have one issue with this replacement, I will install a tankless water heater - and it will not be made by Whirlpool or any of its affiliates. My recommendation would be to steer clear of Whirlpool and their products.

Bought a commercial coin operated Whirlpool washer on 4-18-2015. As of this date machine has not been used that much, the electronic part has gone haywire.All lights on and shows the door lock (which is not) disconnected, nothing changes when I put it back. Contacted Whirlpool technician, have been told that this is a defective model. He has apparently had several service calls that are new machines and they are all the same issue. Told to contacted Whirlpool, Whirlpool playing dumb. I have several other older Whirlpool commercial washers and dryers, never had issues. I guess they are doing shortcut garbage machines. Also, the interior of machine is less sturdy than the older models. Will not buy any Whirlpool products again. They do not stand by their products try to tell me that they are not aware of defective machines. Cheaper to play stupid!!! Disappointed with their lack of standing by what they sell!!!

Our new home came with brand new appliances. I love our Whirlpool microwave. Its reliable, quick & has lots of great pre-programmed features to assist with regular. The independent timer is a total bonus too.

We purchased a Whirlpool upright frost-less freezer (model # EVL201NXRQ05) in October of 2008. So, you see, it is not even four years old. A few months ago I noticed that some things in the freezer were very soft. I looked at the back of the freezer and there was some ice buildup around the area where the coils are located. I took everything out of the freezer and removed the panel over the coils. There was major ice buildup on the coils. I completely defrosted it and dried it out. I restarted it and it seemed to be working okay. But a few days ago, when I got something from the top shelf of the freezer, it was not even frozen. So, here I go again. I removed everything from the freezer and have defrosted it again. However, this time, as soon as I turned it back on, the ice started building up on the coils immediately. It is impossible to contact anyone at Whirlpool that gives a crap. We have also been having problems with our Whirlpool Gold refrigerator. We have spent over $250 on it and it still is not working properly. I would love to just throw them in a ravine, but we have spent a lot of money on these appliances. We thought that Whirlpool was supposed to be number one in appliances. What a huge mistake we have made and it is costing us dearly.

I purchased a refrigerator from this company Model #WRF989DAM. It worked for only 14 months. I had service people come 4 times to try and fix it, called customer service and was suppose to get a replacement, paid $300.00 for a different model, been 49 days and still have no refrigerator in my home. Had to go out and buy my own replacement. I have called and sent emails with no response of when I would be getting the replacement.

Admiral dryer 14 months old and contacts in the timer broke. I contacted Whirlpool customer service and was told too bad, not under warranty. Warranty was for 12 months. Obviously, the timer is defective. How much of a difference do you think 2 months makes? Customer service even said that the parts are made by humans so mistakes will be made. Really? Wouldnt that be considered a defect? Whirlpool has a great web site with a quality circle of promise. What a joke. Guess they dont care about the big picture or their customers. Ill never buy another Whirlpool product. Thats my circle of promise. The repair tech told me that when they go for updated training, that Whirlpool is the worst for providing them with any technical help or specs for their appliances.

Own Whirlpool GB2FHDXWS04 refrigerator for 14 months. From the beginning, the ice maker made gross tasting ice and never got better (had to start buying ice). Then a smell started coming from the fridge every time the fan came on. We called before the warranty was up and talked to Whirlpool, and they said that we must have put something smelly in the fridge that caused the plastic to absorb the smell (which we didnt). They told us to put baking soda in and change it everyday. No change. They kept telling us there is no way it could be giving off a smell for any other reason and if they sent a tech out, we would have to pay for it. Trying to intimidate us until the warranty was up. Then after a month or so, the bottom mount freezer starts leaking water all over the wood floors every 3 days. At first we turned off the water line, but then realized it is coming when the freezer defrosts. One good thing, the freezer, from the beginning, knocked really loud and now that its leaking it doesnt knock. We spent $1,200 just over a year ago and will probably have to go purchase a new one now. I will tell you it will never be another Whirlpool product. Whirlpool has not apologized or done anything but say, Now your warranty is up, you should have bought the extended warranty. Great customer care! With all these same complaints, you would think Whirlpool would figure the problem is their inferior product (which they know) and actually take responsibility.

Bought a Whirlpool dishwasher about 2 years ago. Used it once a day for one year. The bushings already need replacing (maybe $3 to make) and it’s $270 for the part or $280 for whole motor. Do the math. Not impressed.

When our home burned down, had to get a manufactured home. Orig. refrigerator size was 32 cu.ft. This one that came w/ the house is a lot smaller. Weve has issues with ice dispenser several times in the 18 months weve been here. But I would recommend this size.

I purchased a new home and then purchased 4 appliances, all Whirlpool Gold. In less than a year, the stoves electronic ignition and the microwave hood keypad went out. Since they were under warranty, a repairman replaced a bunch of parts and now they are working fine. One month after the refrigerator was out of warranty, the water line to the ice cube maker split about an inch and a half and water would spew out onto the hardwood floor under the unit. We were on vacation for all that month and didnt see any damage until one day there was a puddle in front of the refrigerator. When we pulled it out, we saw that the floor was ruined under the unit, the cabinet next to it black with mold and of course, the line had to be replaced. Whirlpool wasnt interested in the fact that the refrigerator had probably still been under warranty when the split occurred, only that we hadnt reported it before the warranty expired. Next to go was the water seal that goes on the inside of the door of the dishwasher. I was running it about a month after the refrigerator debacle and water came spewing out of the side. The seal had come out and nothing was stopping the water from exiting out the side of the door. Thats 4 for 4 in less than 15 months. I will never buy a Whirlpool product. They couldnt be any worse.

My 15 year old front loader quit working and was going to cost more to repair than we thought was worth it. So, we went shopping at Home Depot and based on discussions with salespeople ended up with the Whirlpool cabrio toploader. What a mistake. I am so disgusted with this washer I dont even know where to start. If there was any way we could return it we would do so. The clothes come out wrinkled, twisted, absolutely covered in pet hair and detergent and fabric softener residue. Yes, Im using HE detergent, in the correct amounts. Yes, Ive read the manual front to back. Yes, Ive tried all the troubleshooting suggestions. No, they dont make a damn bit of difference.I would give anything to have my old front loader back. It was a great little machine that did a wonderful job of cleaning our laundry. Pet hair was washed off, I could lay things out to dry and they werent all wrinkly and did not require ironing. Just about everything that comes out of this cabrio machine that I lay to dry needs to be ironed before it can be worn. It is just a horrible, horrible machine and Whirlpool should be ashamed of themselves for foisting this off on unsuspecting consumers.

I purchased a Whirpool fridge five years ago. To date it has had 7 repairs. The latest round has lasted over five weeks and the expensive warranty I also bought is about to run out. The repair man is on his third repair and I havent had refrigeration for five weeks. In the meantime they wont replace the fridge, and it takes two weeks between scheduled visits by the authorized repair man.

We bought this refrigerator (Whirlpool Model # WRF9913F1FM00) last August 2016. From day 1, the water coming out from the water dispenser was not cold at all. Same temperature as the tap water. By November, the refrigerator started to get warm. Apparently, the evaporator fan motor had to be changed according to the technician who spent more than an hour on the phone with their technical advisor to diagnose the problem with the refrigerator. After a week, the refrigerator got fixed. Not only did the refrigerator started working again, even the water from the dispenser got finally cold, too. Now four months later, March 2016, the same problem: the fridge started to not get cold again. In addition to that, the ice would not come out from the ice dispenser and water from the water dispenser is not cold again. When my husband checked inside the door, the ice were all clumped together. They looked like they melted. And even the ice in the freezer bin looked the same. And on top of this, the refrigerator was making so much noise. The technician was just here again today.

Our first Whirlpool washer barely lasted 1 1/2 years. They replaced it with another one that broke within 9 months. When it worked, it was great... When it didnt, it either overflowed or did not wring clothes tightly on the second rinse.

Just had the repairman at my house to repair my 2-year-old Whirlpool refrigerator Model GB2F4DXWS07 - he couldnt fix it. Just throw it away and get a new one. There is a blockage somewhere in the line, he suspects the lines were not cleaned before it was charged at the factory. Repairman said it was a typical 20-year-old refrigerator problem. Customer service was no help - Whirlpool live chat is currently unavailable. Lousy product with worse service. I will never buy another Whirlpool product.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

I bought a Whirlpool refrigerator, model # wrt779reyb00 with serial # vs13537798. The icemaker quit working and then water started leaking out from the door. A&E serviceman came out to repair and said we needed a new door. It had been over 11 weeks and the door still has not arrived and we have been told it could be as late as November. When I purchased an item, I expect it to work and if not, to be repaired within a reasonable time or be replaced. I have called and been told that replacement is not an option and that I will just have to wait. This is unacceptable. I purchased this refrigerator with water in the door and an icemaker and I expect it to work.

A top loading washing machine with an agitator in my opinion, gets my clothes 100xs cleaner than one without. Ive owned front loaders and top without agitators. Never again. Top with agitator is my personal preference from now on. Also Whirlpool has never failed me unlike other brands.

We bought the microwave in August 2018 and last week it burned a hole through the turn table which broke it and burned a hole in the floor of the microwave. Whirlpool said it was under warranty but refused to bring a new one. They ordered a new glass turntable and painted the spot that had the hole burned in it. What makes me believe it is safe now to use? What caused a microwave to go awry in the first place. It has to be a safety issue and Whirlpool will do nothing about it. Lousy customer experience.

Whirlpool Cabrio Platinum Option - Very stylish. Well built - very solid and heavy constructions. Full features from quick wash to sanitary wash, very energy efficient, steam setting on dryer for touch-ups. Quick loads, etc. We were looking for a washer and dryer set that would accommodate large quilts and blankets and still have the flexibility to handle small and delicate loads, and be energy efficient. The Whirlpool Cabrio Platinum Option is solidly built and very sturdy. It handles small and large loads and is very energy efficient. Both the washer and dryer handle sheets and pillowcases without a problem. Wed recommend them to anyone.

Dishwasher is 15 years old and still going strong. Minor leak which disappeared when I cleaned the gasket. Good internal arrangement for fitting dishes & silverware. One of the best appliances I ever got!

Bought Whirlpool 30 gal propane water heater in Feb, it lasted until May before the unit died. Paid for the extended plan warranty (NEVER do that!). Called support and they said they could send someone out in a little over a week (week with no hot water). The week goes by and on the day it was suppose to be repaired the guy calls and says his van broke down (this was a Friday, getting that early weekend). The earliest they can reschedule is in another week (over 2 weeks no hot water). Called Lowes to see if I can just return it (extended plan and all), no, you need a return code from the whirlpool customer support. Call the Whirlpool number again to ask for a return code, no, it is a repairable problem (even though no one will come repair it). Lesson learned, will never buy Whirlpool or anything over $50 from Lowes again.

Our Whirlpool Cabrio Washer is barely over one year old, and its getting increasingly louder (I cant hear the TV in the other room). I researched this issue and found this is a common problem with the upper and lower bearings. Check it out on YouTube; its easy to find. Whirlpool should buy these back! Is anyone aware of a class action lawsuit against Whirlpool regarding these pieces of junk?

Whirlpool top loading piece of junk! I would give it a zero star review if I could! Do not buy this machine!!! I agree with many other reviews. It doesn’t get the clothes cleaned and now a completely doesn’t work. We reset it, we’ve had the service guy come in and replace a bunch of parts on it. It’s past its one year warranty and doesn’t work anymore. Piece of junk! Junk, junk, junk!!! Waste of money. Do you not buy the Whirlpool tub loading washing machine!

I have replaced the damper control unit three times the last three years. The part begins to fail after nine months in used. The temperature becomes too cold in the refrigerator and the food started frozen because the damper door wont closed as cold air flows from freezer to the refrigerator. It adds to the displeasure that Whirlpool is not taking care of the shipping cost even the part is under warranty.

Purchased 03/28/13. Refrigerator 62 degrees on July 4, 2013. Called for service July 5 - came out July 9 and told unrepairable - wiring harness set against tubing rusted and broke wires. Since July 9, I have been trying to get my replacement from Whirlpool and always told they will call me 24-48 hours - never calls. Asked for supervisor on July 22, then asked for her name and direct number. Supervisor said someone would call me about delivery. Supervisor told me if a local store would have had in stock, they would have sent it out from there (called local store and was told 6 were in stock and could be delivered tomorrow). Tried to call supervisor back to inform her, but number would not go through (apparently bogus number). As of July 22, 2013, still no refrigerator. Very poor customer service/service repair. July 24 - asked if I needed to get an attorney and/or contact local new consumer advocate - Whirlpool said they would issue a refund check for the refrigerator, and that I should receive it in 14-21 business days - said they could not refund on credit card I used to make original purchase. Hopefully, the check will arrive.

Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

1st range arrived in June and would not heat to temperature. Sensor and control panel replaced. After 3 techs Whirlpool agreed to replace in September. 6 weeks later new range arrives. Protective film stuck to the lettering and when you try to remove it the lettering comes off. Chunk of enamel missing off inside oven door and defect in the glass cook top. Fast forward to today. THIRD range delivered. Same issue with the protective film and gouge in chalking around cooktop. Leons has been fantastic. They are replacing it with an entire new brand!

I purchased this washers predecessor, the WTW6200 in May of 09, along with the matching dryer. The bearings gave out after 36 months of use, and our household comprises two adults in their mid-fifties. Estimated cost of the repair? $650! Why am I posting this here? Because two weeks ago, my daughter-in-law called to say that shed so liked my machine when she visited in 09 - Id had the thing for two weeks at that time - that shed bought the WTW8500B and... the bearings were already giving out. I suggested she get the thing repaired, sell it immediately and replace it with an LG product, which is what Ive done.She has been put on a three-month waiting list for the repair, confirming my feeling that Whirlpool, as a whole, has gone down the tubes. Their service record is dreadful, with an excess of 20K complaints existing at various consumer agencies regarding ALL the Cabrio line, and their warranty, Ive learned, is considered the worst in the industry. All in all, the single worst purchase of my fifty-odd years.

Never worked proper form the start, always condensation, bottom froze and top unthawed and vice versa. No help from store or company. During any temp change the fresh food would freeze and top unfreeze and no matter how long you waited and changed settings. Junk.

Whirlpool is a very good company and their products work very efficiently! If I had a choice to choose in a different type of washing machine I don’t think I could choose. Whirlpool is very reliable. Their older machines as well as their newer machines! They last pretty long. The dryer is dry very well as well as the washing machines agitate your clothes to get them clean.

The machine starts shaking uncontrollably, has to be paused and clothes redistributed but still shakes. The stabilizers were replaced approximately 1 year ago. This worked until today. I was was washing a small load and distributed the load accordingly. On the spin cycle, the washer again began shaking and I shut it off. I will never buy Whirlpool products again!