Whirlpool Cabrio 6600 SW2 - Somehow a coin or two (?) are under the tub. It is not a high pitched sound. Just sounds like the machine is rubbing against the tub or something when it is being used. It does an excellent job of washing and spin drying the clothes, but the noise irritates my wife, which then irritates me. I took the top piece off and can see a coin DOWN there, but cannot reach it. Must I turn the machine upside down and try to shake the coin(s) out?

We bought a whirlpool water heater about two and a half years ago and started having problems with the pilot light going out. The gas company said that these have been recalled but he was wrong its the 2005 year. Sure we will have to buy a new water heater soon.

This product is unsafe and should be recalled. It has aluminium wires that connect the unit to the 220 Vol Power source. Aluminium and copper wire dont mix. I took a shower and was getting ready to leave for the day when I went into my garage to smell burning plastic and wires. I traced it to the hot water heater and discovered the wires in the Energy Smart were melted and burned. I checked with Two Electricians who told me that the wires in the unit can not handle the high heat and melt. If you have one get rid of it. Had I left for the day I would have lost my home, cars and pets. If anyone would like to see this unit I still have it and photos.

We purchased a Whirlpool gas range at Home Depot. After less than 2 years the oven would cut off and the time would start flashing. Check on other peoples problems and found out that I was not the only one. Called Whirlpool and the man on the phone told me I could have a problem with the circuit board. Said he could sell me a 1-year warranty to cover service and parts. I think the best thing to do is to buy another oven and not spend any more money on this junk. Never again will I buy Whirlpool or buy appliances from Home Depot

We purchased this washer and dryer new in 2011. Have repaired door to washer twice. New doors total cost $500.00 each time. Now it is cracked yet again and the dryer door has to be adjusted. The temp does not work right. Have to do minimum of 2 cycles for drying. Very unhappy. We may as well buy a new set of another make. Tired of the expensive repairs.

We have had a GX5fhdxvy 07 Whirlpool Gold French door fridge with bottom freezer that is approximately 4 years old. Since the first 6 months of use, so 3.5 years now, we have had continual problems with a flat sheet of ice on the bottom of the freezer which then builds up and leaks all over our floor. Twice I have slipped, once banged my big toe to the point of cracking my big toenail and bleeding profusely, and the second time I slipped on my butt and really hurt my back. This is of real concern as one of my children has Cerebral Palsy and autism and could really hurt himself in our kitchen. We originally called while it was still under warranty and the technician said that we will need to learn how to defrost the tube that seems to be getting built up with ice. Thats the only way to fix it. We thought it meant fix it for a long period of time. After several months of this re-occurring problem, we realized that this is something you need to do very frequently, meaning several times a week. We have had no help from Whirlpool, they tell us that essentially it is our problem. They didnt even offer to provide parts. They were not interested in our problems and just asked us if we wanted to pay for a service call, and that was it. Now but what kind of service is this?? Clearly, after researching these products, this is a design flaw and a lot of consumers have complained about the the same issues. You would think that Whirlpool would have the decency and the business smarts to create a recall to solve consumers issues.Unfortunately, I am not able to purchase a new unit. This was an expensive purchase as it was… and we have absolutely no resolution to the problem. I have to say that after our injuries in our household, eventually someone will slip and do some serious permanent damage to their body or even worse, fall and sustain a head injury and perhaps even die. And although this may seem like a far fetched comment, it really isnt out of the realm of possibility at all! How long does it take for a manufacturer to respond to a flaw in their design??

Whirlpool duet steam model: WFW9750WW00Serial: CSY3601165Please see attached the pictures of our washer that was purchased without a top counter balance from HH Gregg in May of 2010. We were told by the extended warranty technician when he came to diagnose the machine on 6/24/13 that the bearing and basket were bad. He ordered the parts and returned on 7/2 to repair the machine. Upon taking it apart, he discovered the top counter balance was missing and was the reason that the bearing and other parts had failed. I will include pictures of the plastic that the counter balance should have been attached to. You can see there are no screw holes or scuffs on the plastic. It was suggested by one of the customer service agents, Kitty in TN, that we remove the counter balance. Per Kitty, Because had it come from the factory like that, it would have walked all over the laundry room and not worked right since the first day. Honestly, we have scuffs all over our walls and my husband just thought the legs needed adjusted or it wasnt sitting properly on the pedestal. We have never owned a front load washer, so we didnt know what to expect. The washer sits in a very tight space under the cabinets, but will walk in the middle of the floor especially before we installed the pedestal.The top counter balance was ordered on 7/2 and we were told it would arrive and be installed today. The technician called me at 10:55AM today and stated the package had not arrived. We are asking Whirlpool for a replacement washer as the one we purchased brand new came from the factory defective. We have been told a solid NO. Upon further inspection of the machine while taking pictures, I noticed that the bottom counter balance is cracked clear through as well. Im attaching pictures of that. I did speak with Laticia in MI. She was VERY nice and more empathetic than the other 6 or so people we have spoken with at Whirlpool customer service. She was professional, helpful and I hope who Whirlpool would want representing their company and brand.We feel Whirlpool sold us a faulty machine and they should replace it. We have been told by them that they are sending the parts as a GOODWILL gesture, and will have the parts installed. Now after the whole inside of it is shot and possibly the motor and boards, thats awesome. We are now an LG/Samsung family. This was our 3rd and last set of appliances from Whirlpool. When the rest of these die, we will replace with another brand. How sad that what once was a great company, and I grew up with my mom and grandma thinking there was no other brand to use beside Whirlpool, now we are left washerless for 3 weeks. They refuse to stand behind a mistake that was made in the factory. Ive read these are made in Germany. Maybe Whirlpool needs to bring jobs back to the US and improve their quality control.

I purchased a Whirlpool microwave in November 2011 from BestBuy.com. The microwaves handle is coming apart. Best Buy wont honor because I didnt purchase the Geek policy. One year warranty is still valid, but Whirlpool claims that a door handle falling apart is cosmetic. Serial number TR14430004, model number MH3205XVS-2.

Bought a Whirlpool dishwasher approx. 3 years ago from Home Depot and it just quit working. Troubleshooting did nothing. Called Whirlpool to make sure there was no recalls on it. I have owned many Whirlpool appliances and bought this last one because of past good experience. Turns out, after $300 plus repair, it was the control panel. The repairman said, This should not have happened, it is like new. I asked him if he thought it was a lemon? He just looked down, it happens. I am so disappointed in the quality of Whirlpool. I no longer can just buy their products with confidence.

Whirlpool Cabrio Platinum Option - Very stylish. Well built - very solid and heavy constructions. Full features from quick wash to sanitary wash, very energy efficient, steam setting on dryer for touch-ups. Quick loads, etc. We were looking for a washer and dryer set that would accommodate large quilts and blankets and still have the flexibility to handle small and delicate loads, and be energy efficient. The Whirlpool Cabrio Platinum Option is solidly built and very sturdy. It handles small and large loads and is very energy efficient. Both the washer and dryer handle sheets and pillowcases without a problem. Wed recommend them to anyone.

I bought a Whirlpool French door, freezer drawer on bottom at Lowes 2 years ago for $2,600. The refrigerator needed a new motherboard within the first year and now that it is in the 2nd year, service is required again. The repairman ordered the part and came the 2nd time to replace the part upon receipt. Now it needs the 3rd part since it is still not working. I have a herniated disc in my neck and had to remove everything from the refrigerator and freezer to take downstairs to salvage our food. Now I have to go through the same thing again for the 3rd time after the additional part comes. This refrigerator is junk. I asked Lowes for a new replacement but of course was denied. Does anyone know a good lawyer for this type of situation? I never had a problem with an appliance like this.

The Cabrio washing machine I was told by salesman best made so I spent big $$, makes sense right?! Wrong! During spin cycles sounds like jet plane taking off, was told barrings or drive shaft is at fault cause water seeping inside, causing rust, Whirlpool didn’t seal it or designed it to ensure no seepage. Never again Whirlpool. I’m done with your ineptitude, Type: 580. mod. WTW6500WW1. Set.# CY4970595.

Handle needs smarter design. I purchased model #WRT311FZDM00 in November of 2015, didnt install in my new home till December. I am a single senior female, so there is little wear on the fridge, unlike a family of several people and with kids. The door handle actually broke just behind the screws that hold it in place, the plastic part of it broke into a couple of pieces. The cost to replace this handle is approximately $80, which is ridiculous in my opinion. Please start making things of quality materials instead of cheap plastic, especially at a stress point of a part. Even I know better than that. All 4 of my major kitchen appliances are Whirlpool, as well as my washer/dryer. I thought I was buying quality products. Hopefully things will hold up better with the other ones.

In 2012 we bought three new Whirlpool kitchen appliance back in 2012. The refrigerator has needed a drain pan replacement, and two air diffuser replacements. Of course, both air diffuser issues occurred just outside the one year warranty. Then the range oven has required two spark modulator replacements – again just outside the one year warranty. Whirlpool’s solution: buy another 1 year warranty to get it fixed; or buy a new Whirlpool appliance at a discounted price.

Whirlpool Double wall-mounted Oven model#WOD51EC7AW05. Have had nothing but problems (at least 7 problems). The 1st one is a potential fire hazard. Porcelain/enamel shattered on bottom interior panel of BOTH ovens in less than 60 days (exposing underlying metal to rust). Cracked in an odd stress-pattern that indicates the metal expanded during heating, and the porcelain finish did not tolerate the expansion. The lower oven had only been used 2X before I noticed the fracture pattern. Obviously faulty design; a manufacturers defect. Whirlpool claims it is cosmetic damage and when porcelain eventually flakes off, they will send me touch-up paint. (If I dent the outside of an appliance with my wheelchair, thats cosmetic damage. Its a manufacturers defect if the damage happens during normal operation. The appliance damaged itself, not the user.)The preheat function does not work on either oven. The oven indicates it is 350-degrees, when it is actually 125-degrees. Repairman says this is normal; ignore the indicator and navigate by store-bought thermometers”. The temperature can vary 50 degrees on either side of the actual setting (thats a 100 degree range!). Between the faulty preheat and the wide range in temperature, it makes it very hard to bake bread or cake.The rest are annoying problems: The timer is a single “beep” (not even very loud), followed by another single beep every minute. This is not much help if you are folding laundry while the cookies bake. The windows have so many dots on them theyre not clear enough to see how the food is cooking (or read the store-bought thermometers) without opening the doors. The oven produces a lot of steam that fogs up the windows (Ive never had this happen, and Im past the half century point). The exhaust fan is loud and it blows hot air into the drawer under the oven (another potential fire hazard). Dont buy this oven. It has several design flaws and Whirlpool does not stand behind their product.

My refrigerator was purchased in May 2014, and died in August 2015. Before it died, it produced a very loud, rattling noise for two days. Thus, the refrigerator cost me $100/month. It does seem, upon reflection, I would have been better off buying a piece of junk for $50. It would have lasted longer. Additionally, the so-called stainless steel started rusting all over the front surface, first popping up in one spot, then another. One year old, rusty and dead. Great job Whirlpool. Buy American.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

After 12 months (warranty) the bearings had to be replaced, $300. 12 months later bearings needed replaced again for another $300... was told by the repairman not to waste my money. This would happen again in another 12 months. This is a issue with these washers. Opted to get something else. Very unhappy to only get a couple of years out of this machine. I have also had to wash some loads twice to get clean... unacceptable performance!!! Contacted Lowes & Whirlpool to no avail of course. Never again!!

This has been the worst purchase I have ever made! Within 2 months of it going out of its one year warranty I called (Lowes) to have it repaired. Spent $300 on the first repair to get rid of the jet engine sound AND the oil splatter all over the floor then within one month from that repair it has a F code error and wont finish washing a load. It just stops. I have tried everything from unplugging it to restarting and it just wont work. Now have to wait 1 week for the repairman to come back out (hopefully that warranty of 90 days will be helpful). Do Not Buy this machine!!!

I purchased a Whirlpool dishwasher from Home Depot on 2/5/2015. It was delivered damaged on 2/9/2015. Home Depot refused to take it back and Whirlpool sent a tech out to see the damage. I told them I did not want a refurbished dishwasher that I paid almost $1000 for. Whirlpool advised Home Depot that the machine can be repaired. Once again I told both whirlpool and Home Depot that I did not want this dishwasher and to pick it up. Home Depot stated that there would be a 15 percent restocking fee along with a $65 to pick up the washer. Why should we have to pay anything? I am so disgusted for the treatment I received.

I was searching online and stumbled across this site. Funny that there were so many complaints about the console on the ovens, considering that my issue was with the console on a dryer I purchased. I have only had the dryer a year, and it stopped working. There is nothing else wrong with it, no codes, no problems with the lights, or anything else. A technician came out and found that it was a small plastic and metal button piece that helps the press here: spot on the dryer panel to connect to the start button on the console. The little arm had broken and the switch no longer worked.Figured we would have to purchase a new button. NOPE, apparently we were told that we had to purchase a new console (over $200 dollars, close to $300 with shipping)???!!! We were also told that wear and tear can cause the issue. Wear and tear?? On a dryer thats maybe run once a week for about a year? Try again, I think I need my boots because it sounds like horse** to me. I think I will pass this information along to people I know that are technicians so that they can let people know not to purchase from this company because they obviously arent going to address the situation. I think I might also utilize social media to let people know so that they dont have to go through this much aggravation. I certainly dont know what we are going to do, since it took me a year to pay that dryer off, I cant afford another dryer at this time. So unfortunately with a new baby on the way, you wont get any sympathy from me if your company takes a character hit.

The lid stopped locking just over one year after I purchased a Whirlpool Cabrio top load washer, which disabled the washer from washing. After investigating, it seems the electronic control board needs to be replaced, which will cost $400 just for the part. I have a large family, including a disabled child, and a washing machine is mandatory necessity that I cant afford to replace after only one year.

The washer buttons stopped responding after 19 months. Lid lock sensor didn’t work. Replaced control board because new sensor did not fix it. Went bad again after a week. I have to replace it. I think 1 year warranties are not enough for a major appliance.

I purchased this washers predecessor, the WTW6200 in May of 09, along with the matching dryer. The bearings gave out after 36 months of use, and our household comprises two adults in their mid-fifties. Estimated cost of the repair? $650! Why am I posting this here? Because two weeks ago, my daughter-in-law called to say that shed so liked my machine when she visited in 09 - Id had the thing for two weeks at that time - that shed bought the WTW8500B and... the bearings were already giving out. I suggested she get the thing repaired, sell it immediately and replace it with an LG product, which is what Ive done.She has been put on a three-month waiting list for the repair, confirming my feeling that Whirlpool, as a whole, has gone down the tubes. Their service record is dreadful, with an excess of 20K complaints existing at various consumer agencies regarding ALL the Cabrio line, and their warranty, Ive learned, is considered the worst in the industry. All in all, the single worst purchase of my fifty-odd years.

Bought this new in Oct 2012. A week back stopped working. After a week found out it needs new compressor and will cost 1,096.00. Paid 2,100 for this new and now need to buy another fridge but not this make.

We purchased our first front-loader washing machine (Whirlpool Duet WFW9250WW00) just over two years ago. Since we purchased it, it has torn clothes and we have replaced the drum baffles twice (this would be the third time, but we are throwing the washer out), the drum seals twice (another place clothes can get caught). I had adjusted my washing (maybe I overfilled the washer, maybe I was using the wrong spinning speed), but every so often clothing would come out with holes or torn. The drum baffles must come loose before they come out, and clothing can get caught underneath them (I think that is where the tears occur). It has happened at least once a month and I had spent a fair amount of time trying to figure out where the clothes got caught and torn. Many people complain about bad smells from the washers (which I never had - I like the Tide with Febreeze detergent and every so often clean it with bleach or Affresh), but never torn clothing. I would really like to use a front-loading washing machine, but we are going back to the top loader - we cannot afford the clothing tears. I have seen that many people replace baffles (not many speak of clothing tears) and maybe in the future this problem will be addressed. But in the meantime, I would stay away from Whirlpool front-end washers. (GE makes some nice top loaders - and in 40 years of washing clothes and only owning two other washers, I have always thought washers to be an appliance that would last 15 years or longer with very little maintenance or trouble). I believe that I really tried to make this washing machine work out, but it got to the point where my husband did not want to wash baseball uniforms and other irreplaceable clothing in our washer.

Whirlpool fridge still freezes water in the bottom of freezer... after five service attempts. We purchased a five-year warranty and so far, they claim that as long as the warranty is good, they will continue to warranty it. We now have three and a half years left. We have currently owned our refrigerator for just over a year (approx. 18 months). During this time, it has had the same warranty repair issue that has been serviced five times so far. We now have an appointment for a sixth time since RC Willey does not want to fix a lemon the right way. The first three warranty repairs were under the manufacturers warranty. We are now under a warranty (extended) that was purchased from the place we bought the fridge from, RC Willey.I want my money back on the whole deal. I was going to be civilized about it because I thought they were common sense decent place to buy from. I thought they would, through common sense, realize that this unit is a lemon and allow credit towards another fridge. In just the past two years, we have bought from RC Willey over $10,000 worth of flooring, appliances, etc. and thats not counting previous years.

In August of 2013 the lid on my Whirlpool Cabrio, model #WTW7800XW0 simply fell apart. This washer was purchased from Lowe’s in Live Oak, Florida on August 23, 2010. Lowe’s put me in contact with the authorized repair service, A&E Factory Service. The A&E technician arrived and told me the hinges were the cause of the lid breaking apart. He ordered a new lid and new hinges. When the lid and hinges were delivered the technician came back to my home and looked at the hinges again and said they didnt look that bad so he didnt bother even opening the box with the new hinges. He just put the new lid on and said I shouldnt have any further problem. The total cost of the new lid, hinges and service call amounted to $385.50. Well, here it is - not even a year later and the same problem is back with me. Yesterday (July 23, 2014) I was doing a load of laundry. When the load was complete and the lid lock turned off - the lid actually sprung upward and now the lid wont close. It seems that Whirlpool is fully aware they either have a design flaw of defective lids and they are gouging the customers for their errors. The Cabrio model is supposed to be top of the line - certainly not a cheap machine. I was, at least, happy with the performance of this machine cleaning my clothes properly but this lid problem is ridiculous. I do not plan to purchase any Whirlpool products in the future if they do not make things right by myself and hundreds of others with this same problem.

We purchased a $3000 WRF990SLAM00 / K22019120 refrigerator in 2013. Within the first two and a half years we have already put over $700 in repairs. We were told today the coolant for the ice maker has a leak (either a slow leak or a fast leak, they arent sure). But from here on out we will have to put coolant in it to keep the ice maker working. A week ago we spent another $300 to repair the water dispenser. This is the worst fridge we have ever owned. Whirlpool could care less and we are basically out right at $4,000! DONT BUY WHIRLPOOL.

I chose a Kitchen Aid Stainless Steel, Counter Depth Refrigerator from Lowe’s in early February, 2018. (Model #KRFC300ESS) At the time KA was recommended as the best choice. 1) Within a month there were numerous rust stains on the French door and that needed to be replaced and 2) There is the Damper Control unit which makes a intolerable noise until you replace this motor. This noise then returns....about every three months. Plan on paying just under $200 every year for the life of the refrigerator (at average of 14 years= $2,800!). We have had servicemen to our home now 4 times since our 2/7/18 delivery. A local retailer just rated Appliance Brands in 2020 for reliability and the amount of times serviced and found Kitchen Aid to be 10 of the 10 listed. My recommendation would be to try another brand. This one creates a money pit. :(

Had to return my first 2019 purchase due to refrigerator freezing food and imbalanced top doors. I was unable to get straight answers from Whirlpool and so the mgr at BB gave exchange same problems except door not as off. Cheap product make/model. A class action lawsuit from 2016 has occurred and the company continues to distribute the same issues in their new make/model.

Whirlpool Gold Series Dishwasher Model # WDT710PAYM6 - Purchased this dishwasher in July, 2014. Last week the dishwasher powered off mid cycle. Could not power back up. Tried a few suggestions found online to reset which did not work. I had both a plumber and an electrician look at it. All water lines were fine and power coming in and out of dishwasher and control panel was checked and all looked okay to electrician, but could not get the machine to power up. No longer under warranty. Very dissatisfied there is no recourse.

We bought this fridge 1 year ago. We have already been without a fridge from Oct 2016 to Jan 30, 2017 due to a drawer going bad which caused the whole thing to quit. Now it has an obstruction in the Freon lines that causes it to freeze up and not cool. It was deemed not repairable by service company sent by Whirlpool/KitchenAid, and yet they want one more test run. The last person I spoke with at customer service had a flippant attitude and said there are no notes. What they do is drag you along for so long, make you wait and abuse you with tests, and hope you finally give up and go away. I will never buy another thing with Whirlpool/KitchenAid stamped on it!

I purchased the Whirlpool Cabrio washer and dryer about 5 years ago. I wanted to pay for a good pair to last a long time for the money. We have had a repair man out twice for the washer. They ended up replacing the computer board. It worked fine for a few years. Now, it keeps getting the unbalanced error code for almost every load of clothes that we start. Sometimes, it takes 20-30 minutes of rearranging the clothes to get it to finally work. I have had to manually set it to finish the loads on a number of occasions. It is so time consuming to do laundry due to having to play with the clothes to get the loads to finish. Plus, I dont know how many times it has woken up my grandkids because of the loud thumping noise it makes when it gets unbalanced. I have never had a washer do this. I would expect when you pay big bucks for an appliance that it should last a long long time. One usually gets what they pay for. I should have bought a cheaper pair. Then, they probably would have lasted 15 to 20 years.

I purchased a Whirlpool Cabrio washer and dryer from a local appliance center. Everything was working great. After some time, the washer began to have error codes. I would have to turn it off and restart using more detergent, more water and more electricity to attempt to get a load washed. I did purchase an extended warranty. I reported the issue to Whirlpool and I have had 7 home repair visits while still under Whirlpools warranty. The first time, the repair tech went under the washer and tightened a screw. REALLY! The next visit, the motherboard was changed and the issues kept coming back. Well, the Whirlpool warranty was now over so the extended warranty had to be picked up from the appliance center. Things got worse and had continued repair calls. After I had enough, I called Whirlpool and spoke to everyone under the sun. I tossed it outside and bought another brand washer. Several weeks went by and this washer still under the shed, Whirlpool contacted me and bought back my washer, GREAT.Now, here it starts all over again with the dryer, same issues with motherboard. Only this time, I am 1 month out of Whirlpool warranty and need $385 for a new motherboard plus cost to replace. I call Whirlpool again but only this time, they show no issues with this dryer and are not budging. I toss it out and again, purchase another brand dryer. I grew more angry by the day looking at this dryer sitting useless outside. I had it hauled off as trash. My question is how does a consumer protect themselves against these manufacturers? I do understand warranties but if it smells like a lemon, acts like a lemon, it must be a lemon!

We purchased a mid-grade Whirlpool Gold Series dishwasher a little over 2 years ago. 14 months in, the motor failed, requiring a $295.00 repair/replacement. That was nine months ago, and now the motor has failed again. That is outrageous! No more expensive repairs on this piece of junk. Its going to the scrap heap. We just ordered a Frigidaire. While I have no experience with that brand, it cant possibly be as bad as Whirlpool.

Washing Machine Model WTW4616FW - I purchased this machine at Home Depot after I had to return my Samsung Costco machine that was recalled due to the glass top flying off. I was attracted to it by its simplicity in design and price. I have had it almost a full year and love it. I like that it has the deep water wash for over-sized items and a full-sized agitator. I was shocked that it was actually Made in America. I highly recommend it and I hope they keep making this reliable machine that gets the clothes clean. Awesome machine without the bells and whistles that I dont expect to breakdown. Way to go Whirlpool!

Refrigerator ice maker quit working. This is replacement fridge for first refrigerator that quit working same model. This one has electrical burn marks inside behind a panel. Whirlpool says this is normal. How can burn marks inside a refrigerator be normal. If house or fridge catch on fire will be suing Whirlpool. Ice maker and water valve replaced. Still not working. Maybe it has to do with the burn marks.

I have a Cabrio washing machine and the circuit board has gone bad. I understand from Whirlpools customer service that if your machine was made before 2005, they are fixing the issue. Mine was made after 2006. Even though the problem is the same, Whirlpool will not correct the problem. I was told it was fixed in the new machines. The circuit board goes bad and you have to start and stop the machine at least three times before it will start your cycle, then it stops again at the 17 minute mark and you have to cancel and start the machine again for it to finish its cycle. The error is F1. Customer service acknowledged that this is a known problem for the Whirlpool machines built before 2005 but deny any claim that is is happening to the machines after 2005. Looking at all the other complaints, it is still a problem. I am disappointed in Whirlpool for their customer service attitude and for them not standing behind their product and fixing a known problem. I have always bought Whirlpool products but going forward will be switching to a better company. Shame on you Whirlpool. For a machine I spent $1000 on, the part is going to cost $300 to fix.

Sad that I have to file this review! After reading multiple other reviews on all brands available to American citizens, I have come to the realization that cheap labor and materials are creating massive appliance garbage in our country as well as financial rip off for us all. It needs to STOP! What has happened to doing things right!! What company is going to be the first to produce good refrigerators! Paid over $2000 for my side by side and it is only 5 years old and has a freon leak that cant be fixed. Repairman said will have to buy a new refrigerator. Pathetic!! Cheap manufacturing in foreign countries is killing our economy and our household finances. Be prepared to buy NOTHING that works! Yeah, thats what I work hard for and look forward to. Americans better wake up.

I purchased a Whirlpool Cabrio washer and dryer. They work well but the washer underneath lid has rusted already. I did purchase the washer in Dec. 2011 and in June 2012 the inside lid to my surprise had rust on it. I called the Whirlpool company and was told that is considered cosmetic and not covered under warranty..

Bought a Whirlpool French Door, Bottom freezer mount appliance from Lowes in Jan 2014. Model WRF990SLAM00. Jan 2015 the freezer part stopped working. Whirlpool approved repairman came and knew exactly the problem because he was aware of this being a consistent issue with Whirlpools. He contacted Whirlpool and they quickly agreed to send repair kit for FREE. Took 2 wks for parts to arrive, and neglected to send along required tool/gauges for repair to occur. I called Whirlpool C.S. and they claimed they knew nothing and said our fridge was on no problem list. I had repairman call Whirlpool and they claimed appropriate tool/gauges are no longer available! This fridge is only 1 year old!!! Now we are completely ignored. Whirlpool will not even talk to us about help of any kind. HORRIBLE customer service!!! Crappy appliance! After thinking our Whirlpool appliances were a good investment, I will NEVER EVER BUY WHIRLPOOL AGAIN!!!

I purchased a Whirlpool classic range model number rf263LXTS0 on January 2010. We had some hang-ups on the kitchen renovation and were not able to install the appliances until May of 2011.I used the cooktop that evening and was very pleased. I then went to use the oven 2 weeks later and it did not heat up. I asked the contractor to check things out (maybe it was something minor that he could fix). He checked the things that he installed and everything on his end was working fine, so he told me to call Whirlpool.A service technician came out and, within 10 minutes, said that the oven controls were defective.I paid $450.00 for the oven originally. The service technician charged me $136.74 for 10 minutes to tell me that the oven control needed to be replaced (that is the major part of the oven) and that it would cost me $318.41 to replace the part.I called Whirlpool and explained my circumstance and Paula, the supervisor from Tennessee, said that there was nothing she could do. I told her that even if I installed the oven back in January of 2010, the major part of the oven should last more than 1 and 1/2 years.What terrible craftsmanship and crappy customer service. It is sad that customer service cant stand by their product and Whirlpool has to rely on making their money on repairing defectives products. I now have to go out and buy a new oven. I also buy a lot of appliances in my business and I will never buy a Whirlpool again.

Purchased WP fridge, stove, and dishwasher at the same time. All were the gold series. At 20 months, freezer stopped cooling. WP would not cover the repair. Refrigerator has been noisy from day one. This company does not care about their customers.

Whirlpool Range Model XFE381LVS - 12/13/2014 4:30PM Wife was cooking dinner and turned oven on. Smoke started coming out of the back and called me. I ran to the breaker panel and turned off the breaker. Back to the stove, pulled it out and smoke still coming out in back at the top. I could see fire in the top of the back panel. Slowly the fire went out. Unplugged the stove, I removed the back panel, wires were still smoldering and the Control panel was burned thru. Took pictures so I could contact Whirlpool Monday. The Electrical control panel is destroyed as well as many wires. Glad we were home and oven was not left on while we were out in the yard or Home could have been destroyed. Purchased the stove from Lowes 11/02/2010 with a extended warranty. Tried to add receipt but would not accept, wrong type doc.

My landlord replaced our old Whirpool topload washer with a Whirlpool HE topload machine last year. Looks sleek, lots of settings BUT IT DOES NOT GET CLOTHES CLEAN - not on any setting, not if loaded as recommended or under-loaded, not if I use more or less detergent, and not if I follow all the tips for getting rid of residue. This machine so under-performs I have to spot clean my clothes AFTER I was them. And were not talking deep dirt or grime here, or things that need special treatment, Just ordinary dirt dirt, to which the machine adds gray streaks of dirty water residue. Thank God I didnt buy this turkey for myself -- I will NEVER buy one of these machines. I did two small rugs today and they came out dingier than they went in. These machines should be recalled. If I could give it less than one star, I would.

My Whirlpool washing machine has not worked properly from the first day. Whirlpool washing machine customer care is pathetic. I bought a Whirlpool semi-automatic washing machine, Sparkle. This product is in warranty period. From the first day, this product did not give right result. Machine sound is very high and I called customer care center may times (around 9-10 times). They sent this machine three times in service center but the results remained the same. The problem arose when we put some load in it. He said the gear box should be changed and the machine should be cleansed off the dirt. He offered some powder costing Rs. 1500/- to be used in washing machine.Later, he asked Rs. 350/- for other parts after two months then I paid them again after 15 days for a piece that did not work. Then, they want to charge me Rs. 350/- again. When I showed the previous slip, they then changed that part without any cost. But after 15 days, again same problem occurred. They charged me 150/- Rs. but the problem is the same. Total money I spent is Rs. 1500/-+350/-+150/-. I also purchased a stand and cover for safety, but what will happen if product is not good? The technicians visited many times and they all said this piece is not okay but they cant do anything. The company should change this product. The machine is still rotting at my home. Im not sure if it could be accepted to be exchanged for a new one. Customer care gave us the satisfaction code but technician did not ask for this code. Im really very sad that I have called around 10 complaints within two years. Why are you people not listening? You all are doing time pass. You can check my complaint codes in your records and ask your technicians about Noida. Many times, I did not note the complaints number. Please open my file and check the issue. I told the technician many times that I want to talk to your seniors and want to tell them the problem because from the first day, it was the same, but they refused. I have also purchased a 320 LT fridge from you but that product is very nice. You should listen to our problems. This was not expected of such a branded company. I promised myself that I will never in my life purchase a Whirlpool product and advise the same to others.

Ice maker kept freezing up. Im continually taking the ice tray out to unfreeze. The frequent removal of the tray eventually broke the tab off on the liner. Ive now been told this (liner) is not a replaceable part and since that is the case, the warranty will not cover. Im upset that the repair technician did not process the claim properly and state that the make had a problem freezing. What kind of company would manufacture a product that would have parts that are unrepairable? You spend close to $2,000 on a refrigerator, wouldnt you think you would have an ice maker that works? I know they hope to sell more appliances this way but you can bet I will not be purchasing another Whirlpool anything! I will also be retracting my recommendations to friends and family to purchase a Whirlpool. The company does not stand behind its products.

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

Im with the rest of the people on here... The only mistake I made was not checking the reviews before purchasing a Whirlpool product. My washing machine is horrible... I dont recommend anyone purchase any Whirlpool products. Its cheap and has already stopped working twice in the last 6 months... I have had a repair man come out twice to replace the door locking mechanism... Not to mention the buttons dont work, they just slide back into the machine... Plus, you have to jump through hoops just to get the machine started the way you like it... If you make a mistake, there goes your whole ** load of laundry, not to mention the water wasted. Hell with Whirlpool - Dont ever buy a whirlpool product as long as you live.

We purchased a dishwasher for $650 and within a very short period of time, the upper rack was so squeaky that it was intolerable. Service guys came and replaced the rack and wheels and all was well until a few months passed and it happened again. At that point, it was outside of the warranty, so we called upon our extended warranty we bought through Whirlpool. Guess what? That warranty doesnt cover the racks. So they referred us back to Whirlpool. They told us we had to pay for it ourselves. After being treated like a ping pong ball several times, we ended up paying about $150 for labor for another guy to come out and replace the racks again. Whirlpool agreed to pay for the parts. A few months later, we again have a squeaky upper rack that is so loud it wakes people up in our house and its less than two years old at this point. Weve been sold a LEMON!! Just got off the phone with a supervisor at Whirlpool who said they cant do anything about it and wont acknowledge we have a lemon. When I told her I was going to take this as far as I need to to resolve it, even if we have to go to court, she laughed out loud at me. We will never again buy a Whirlpool product. Our LG appliances have been great however.

I have a kitchen collection of Whirlpool products, not even 2 1/2 years old. I have had nothing but issues. Microwave was completely rebuilt within few months, refrigerator and freezer multiple issues. Latest is the freezer stopped working, now my good is ruined!!! Wont always make ice in the icemaker. Already had to replace freezer door because it was warped and the seal didnt work and now my dishwasher isnt working!!! **!!! I waited 20 years for a new kitchen, finally got one and did extensive research thinking I was safe with whirlpool. I was wrong. So now what, what happens when the warranty runs out, Im screwed. Shame on you whirlpool for putting out crappy products and doing NOTHING to try and fix this!!

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

This washer has been a lemon since the day we bought it. Always leaves marks all over dark clothes. Had to have a part replaced before we owned it a year & repairman from the company said they have to replace that same part every time they go out so they carry them on the truck. Latch broke after owning it for less than 2 years & now it no longer spins water out of clothes. All this & we havent even owned it 3 years. I had a GE washer for years when I first got married & had children. Never had problems like this. Paid it off on Monday & on Friday it became a piece of junk. How is Whirlpool getting away with this misrepresentation? I dont even see how they can call it a washer.

The pilot of my Whirlpool hot water heater (model FG1H5040T3NOV) suddenly went out and I called in a plumber to check it out. He managed to restart the pilot and we had hot water again, but it went out again within 12 hours. He mentioned that I would most likely need a part called a thermo coupling and I should start looking for it. Well, I found this site and read one of the positive reviews that provided the WP toll free number, so I called. Talk about great customer service! Ben was amazing – he took down all my info and was very helpful. Even though the warranty expired years ago, he overnighted me the replacement parts I needed at no charge. And there’s no charge for shipping either! My plumber is completely anti-Whirlpool HWHs and now he will change his mind when I tell him how efficient they are. I also hope he doesnt charge me a bundle to install the replacement part.

I have a Whirlpool cabrio washer (Model: wtw6300 Serial Number: CT3573525) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. At the beginning, I didnt care because I had warranty with BrandsMart. I had to call at least four times. But now, I bought the automatic control and it didnt work. For two days, I was trying to balance this machine but it is impossible since the beginning.I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool. Two of the gas burners of my Whirlpool kitchen, after two years of use, are no longer working. I will definitely contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

A top loading washing machine with an agitator in my opinion, gets my clothes 100xs cleaner than one without. Ive owned front loaders and top without agitators. Never again. Top with agitator is my personal preference from now on. Also Whirlpool has never failed me unlike other brands.

It is a good refrigerator for the price, but it is not big enough for our family. It does get very cold in the refrigerator part unlike our last refrigerator. I only wish it had more shelf space on the door and the egg place fit more than 6 eggs.

We purchased a Whirlpool front loading washer about three years ago. During our first year the machine worked OK, but three months after warranty expiration (12 month warranty), the sensors seems to go wonky and it no longer worked (at 15 months of age). We paid about $95 in the Minneapolis area for a service call. The repairman had to call Whirlpool from our home to inquire about the sequence of flashing lights on the sensor. After getting off the phone he told us he thought he knew the problem, but could not guarantee that the $200+ part he suggested ordering would solve the problem. The installation would require additional labor charges, of course. I reported the incident to the manager of the repair service and was told the repairman was expert in Whirlpools but this did not further inspire confidence. We were not willing to sink this amount into the machine, so ditched it and bought a top-loading inexpensive Roeper. The top-loading machine definitely appears harder on the clothes than the front loading Whirlpool, but it gets the clothes cleaner and has been problem-free so far.

We bought a complete set of Whirlpool Appliances three years ago. The set we bought were in the upper price range. In the past three years: The freezer began forming ice on the bottom which melted and poured water all over the floor (a unit on the freezer had to be replaced 18 months ago). An element on the stove quit working and had to be replaced (12 months ago). The ice maker quit working and had to be completely replaced (9 months ago). The dishwasher quit working and the entire motor had to be replaced (3 months ago). The ice maker quit working again four days ago. The repair person who just came said the entire unit needed to be replaced, AGAIN. He said the warranty on the part is only 6 months. I called Whirlpool itself - their warranty is only 1 year. The fact that their warranties are so short, and there are so many problems with their products is evidence that they do not make products to actually work. They simply make them to sell. They do not care if the product works once the consumer has paid for it. This was obvious in my conversation with the Whirlpool service person. She took 10 minutes to gather all my personal information then took 10 seconds to tell me there was nothing they would do.

Not working at all and only 3 years old. Completely non-functional. No fridge or freezer. Lost all my food. Garbage. DO NOT BUY.

Buyers beware of Whirlpool ovens! We bought a Whirlpool Built-In Electric Oven in August 2008. Fifteen months later, I decided to clean the oven for the first time and when I turned it on the auto-clean, the entire control panel went dark. The technician said he has seen this problem several times in such ovens and was able to repair the oven. I called Whirlpool and they had not heard of this being a common problem. Last week, the air blower wasnt functioning and had to be replaced. I called Whirlpool again and told them about this second incident in a 4 year old oven that is not used frequently. I told them their quality assurance people and/or engineers need to re-evaluate their products. My lesson learned is that I will never purchase another Whirlpool or Whirlpool related product.

I purchased 5 Whirlpool appliances when I moved into a new home approximately 5 years ago. The selection buttons on the plastic panels on the front of 3 (dishwasher, washer and dryer) out of the 5 appliances has either broken completely through or are in the process of breaking through, leaving an ugly appearance on the front of the appliances. When inquiring if I could replace these panels, I was told that one (dishwasher) would cost me $100.00. I believe that the structure of these panels has been extremely poorly manufactured. Why would you put perforation around each button? It is obvious that they would push through. What can Whirlpool do for me?

Purchased above refrigerator (WRF736SDAM13) over a year ago and it has been nothing but trouble. Ive had service companies out 6 different times. The doors never lined up or closed properly from day one. The final and last attempt to fix was putting caulk in the seal of the doors!! Left door does not seal properly and moisture builds up on inside. I requested several times for a new one and Whirlpool refused. Also purchased microwave, stove and dishwasher. Microwave went out 6 months after using it. They had to replace a major part. At least they did this at no charge. Just the hassle of having to be home 2 times to meet service tech. WILL NEVER purchase Whirlpool appliances again. Ive been using them for in all my homes in the past. STAY AWAY from this model.

I really enjoy the self cleaning option on this unit. It really cleans everything without chemicals and then you just vacuum up the dust. My dislike is the ceramic top though. The top scratches really easily and hard to clean up spills during cooking. Overall I would give this stove a b rating.

8 cu. ft. Cabrio® High-Efficiency Top Load Washer with Steam - I bought a new washer. It did a poor job rinsing and spinning dry. Whirlpool customer threatened me that a service charge may be charge if the repairman came out and found nothing wrong. After calling three times I ordered a repairman out. The repairman explained that only way to prevent soap residue on your clean clothes is to use the bulky and deep water options. Also dont use high spin or when it spins your clothes dry, it leaves them in a tangled mess that requires ironing to remove the wrinkles. This washer is not ready for the market and must be removed until they can perfect it. It cost me $200 to return and exchange this model for the Front Load Duet, which works excellent. Whirlpool should be ashamed to have ever put this machine on the market.

I purchased my stove in June 2020. I had no idea it was to be connected to the internet, but no big deal. Had I known of all the other quirks I would have thought twice. 1: A red light comes on to tell you a burner is on but not which one. 2: A red light appears when a burner is hot but it doesnt show which one. 3: Only 3 burners out of 5 can be used for cooking the other 2 are warming and melting ONLY. 4: The stove updates its software whenever it feels like it and shuts off the oven and burners. 5: Periodically I have the oven on and it just turns itself off!6: The touch controls for the oven are in a bad spot because if you accidentally touch them when the oven is on the oven will shut off.Not sure if it has any serious problems just the inconveniences listed.

In 2007, I purchased two 30 gal. Whirlpool Flame Lock water heaters (Model: FG1F3030T3NOV) from Lowes for two different homes that I own. I started having trouble with one of them after about two months. I replaced the thermocouple several times, with each one working only about a month. After that, Lowes replaced the complete burner assembly and that, so far, fixed the problem.Now, the second one has (1 Oct 11) gone out. The local Lowes told me that they are out of the burner assembly for this water heater. I called them this evening and was told that they didnt know when they would have the part, but to call back about every other day to see if they had received the burner assembly for this water heater. They said that it could be from two days to two weeks before they may receive this part!In 2008, I also purchased a 40 gal. Whirlpool Flame Lock water heater (Model: BFG1F4034T3NOV) for my house and no problems so far. In 2007, I even recommended that a friend of mine purchase and install one of these in a home that he owned. He did. I helped him install it and it later had the same problems! I am now needing a water heater for my workshop. What can I buy thats dependable?

The exhaust fan for the gas range runs when using the microwave. The noise is loud and very aggravating and there is no way to turn it off. From what I can find the older models there was an option to turn it off. On the new models Whirlpool cut costs by not putting a small (QUIET) fan in the microwave but used the range fan for a dual purpose.

Our new home came with brand new appliances. I love our Whirlpool microwave. Its reliable, quick & has lots of great pre-programmed features to assist with regular. The independent timer is a total bonus too.

Our Whirlpool refrigerator has been an extraordinary kitchen appliance, it may even be 28 years old. The ice maker worked until just four years ago and thats amazing. Its never been serviced and never needed a repair. I dont know what one can say about something thats worked so flawlessly. This seems a little bit trivial when considering the cost of a new appliance, but the plastic veneer on the handle had fallen off and needed glued back on, but thats about it as far as maintenance and repairs go. Overall its been an ideal purchase and I wish wholeheartedly all my purchases were as good as our whirlpool refrigerator.

I called Whirlpool’s 800 customer service line to let them know I was having a problem with this loud humming and rattling noise coming from my refrigerator because of a manufacturing defect (according to the service tech that came to my house to fix it). Apparently, the metal grid is being held by a flat mental hook which vibrates. What a loud noise. We cannot eat in our kitchen: the noise it terrible. The repairmans solution was to put a piece of rubber between the two metal pieces. It worked until he left. I told him it would start again and it did! I even let the customer service rep hear the noise and she agreed. I am in the early stages of my problem, but from what I have read I am not very hopeful. I would like to have the names and phone numbers of the people at Whirlpool who refused to help. Maybe if we would all band together and call them, they would get tired of hearing from unhappy customers and fix the problems. I am game. Anyone else?

After Hurricane Katrina, six years ago, the gas water heater in my house had to be replaced due to the house getting flooded. For the past six years, the pilot light and/or igniter for the gas water heater has had to be replaced if not once a year, twice a year because it will not stay lit. Each time, Whirlpool would send a new igniter and/or pilot light part and would reimburse me the cost of labor to have the part(s) replaced.Now, after six years and exhausted of fighting with Whirlpool to stand behind their product and make it right, they are finally giving me an authorization to get a new gas water heater. However, now they are telling me they will not cover the cost of labor for replacing the entire water heater. My plumber will have to pull the defective water heater out of my house, take it to Lowes, pick up the new water heater and install it in my home. And Im supposed to accept their not paying for the labor of replacing their faulty water heater? I questioned this and told Whirlpool they paid for labor for the parts to be replaced for the past six years. Whirlpool then said they would pay up to $100. This is not acceptable. I was reimbursed more than $100 for the labor to replace a part that fits in a shoe box. (Multiply $100+ times 6. They paid more than $600 over the past six years.) The cost to replace an entire water heater, picking it up from the store included, will cost more than $200, if not $300! I would not have to pay anything if the Whirlpool product was not defective!I told the manager I was speaking with at Whirlpool I wanted to speak with his boss or someone who had more authority than he did. He refused. I asked him, Was he telling me no I could not speak with someone above him? He finally said he would have someone call me.I believe I should be reimbursed for the entire amount of labor to replace the water heater since the water heater is a defective product and I have to have it replaced not by my choice but out of necessity and safety. If it is defective in one area, who is to say in trying to light the pilot light, one day it will not do something worse than just not light up. What if it decides to explode? Defective is defective and I feel my family is in danger from a defective product and it should be replaced at the cost of Whirlpool not mine.

I purchased my Cabrio washer and dryer 4 years ago, my dryer doesnt dry completely, I have to do 2 to 3 cycles to dry. My washer has an f51 code and I have problems unlocking the lid and it takes 2 to 3 hours to wash. This is ridiculous and it causing my electric bill to spike. Is there a recall on the Cabrio?

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

Had the entire kitchen remodeled. We bought a Whirlpool Gold French Door refrigerator from Sears, did not buy an extended service contract. The refrigerator has NEVER made an ice cube. The water dispenser in the left door sometimes works, mostly not. The fridge freezes the food inside, temp. set at 41°F. The entire ice maker has been replaced, several valves have been replaced, a service company rep. tore the back off the fridge, found some insulation misplaced, said he repaired that. We have been very patient. Three repair companies have been sent out by Whirlpool, two said the refrigerator CANNOT BE REPAIRED. Whirlpool told me the only resolution is repair.Whirlpools Customer Experience Center is a joke, they do nothing but try to schedule another repair call. Tell you how sorry they are about your problem but do nothing to solve the problem. Carefully trained to give you the BIG runaround and nothing else. You never get the same person twice or the same city twice. Patients exhausted. Calling my lawyer. I would strongly advise anyone needing a new refrigerator not to buy a Whirlpool product. You should also check the list of other brands they make, there are several. I wouldnt buy them either. Buy a fridge made in Japan by a Japanese company. They get it right and know the Quality Process.

ED5PHEXNK00 Stainless Steel side by side Refrigerator bought in 2004, look out!The refrigerator caught fire today and there was smoke everywhere. Had I not been home, damage would have been out of control. I traced the smoke to the bottom of the refrigerator. I pulled the unit out from the wall and unplugged the power to the unit. My unit is out of warranty and past the extended Lowes warranty. The repair diagnosis is $100 to start.Whirlpool has recalled its other brands (Maytag, etc.) for this same problem but not its Whirlpool brand. Our problem is the same problem with hundreds of other people: Whirlpool fridges burning, smoking, and being a life threatening hazard to families all over America because of the faulty relay to compressor. Whirlpool better recall this model. They need to fix this or they will have much bigger issues to deal with (corporate manslaughter from a known issue and no action or protection for its consumers). The refrigerator is a result of Whirlpool’s negligence; thus, it’s potentially deadly.

My front loading machine is moldy and smells terrible ALL THE TIME -- I hate this machine and will never ever buy one like this again. I spend more money on cleaner than I do on actual laundry soap.

Purchasing this refrigerator Model Number WRS571CIDMOO in September 2015 and now only being May 2017 the ice maker has stopped working. When I contacted Whirlpool USA they offered a warranty plan for $454.00 for one year when I purchased the refrigerator for $989.00. I told the representative, Why would I pay that much money for one year of service when I purchased the appliance for half of what the service fee? I now will no longer purchase anything from Whirlpool when other brands last much longer!

I purchased Whirlpool top loading washing machine model # WTW57ESVW less than 2 years ago. It stopped working yesterday. I had a trusted professional repairman evaluate it today. The motor needs to be replaced after less than 2 years?! The customer service reps basically said sorry. I should have purchased the extended warranty. Is it not reasonable to trust that a Whirlpool washing machine motor should last more than 2 years.I am very unhappy and very angry that Whirlpool will not stand behind their product. The last customer service rep I spoke to suggested she could send one of their repairmen and replace the motor at a cost to me of $299.00. So, after less than 2 years, I am offered an amount to pay of about half the cost I paid less than 2 years ago for the brand new washing machine. My home is full of Whirlpool appliances. I have been a good and loyal customer for over 30 years. I am very angry and upset with Whirlpool. Please explain to me why it is not reasonable for me to trust and believe that a Whirlpool top loading machine that is well cared for and not abused in any fashion should last longer than 2 years? Is this being a loyal Whirlpool customer gets you, I should have purchased the extended warranty”? We are talking about a motor here, not a fabric or bleach dispenser that breaks. Although, those parts should not break either, there is a big difference from something like that and a motor. Please contact me as soon as possible at either number listed above. Thank you.

The space could be laid out a little better. The flimsy shelf is not real stable for foods or ice tray. Where the shelf locks into the side wall is not deep enough to stabilize the shelf itself. The flat indentations in the bottom, where they meet the front, have an edge that makes properly cleaning the freezer a bit difficult.

The drawer guides on the large clear drawer at the top of the whirlpool refrigerator are very flimsy causing the drawer to drop when pulled out to the stop. When I called about this I was told it was cosmetic and not covered under warranty. I purchased the extended warranty which will replace the flimsy parts with the same flimsy parts. On 6/24/2024 Denisia sent me new side rails, exactly the type I have. I replaced them but the right side one broke. I regret ever owning one and will not recommend a whirlpool product to anyone. It is very obvious to anyone, after using this product, that that particular part is not safe and is definitely more than a cosmetic problem. I have already dumped the contents on the floor once and have just managed to catch it more times than I care to count. I spoke with Danielle on 5/14/2014. She sent the small plastic drawer that goes on the bottom.

I have always used Whirlpool washers and dryers. There are many models to choose from to meet a families needs. I can only remember one time when I had to replace an operating part to improve performance.

I purchased the Cabrio washer/dryer in 2006. We have had it repaired 6 times and I even purchased a two year extended warranty after having issues with it the first year. Now I seem to be in the same boat. The washer will not spin and drain. This has already been looked at by a technician several months ago. I feel like this product is faulty and has not worked properly from the start. Are there lemon laws for appliances? It seems that this product would qualify. I will never purchase Whirlpool again.

I saved my money a long time to purchase a new refrigerator (Whirlpool Refrigerator Model ED2VHEXV001). I have very low income so this was not an easy task. April 2009, purchased from Lowes. Ive read similar complaints and also believe there is a defect in the plastic material as there are cracks everywhere on the interior. Shelves have cracked and the whole thing is of poor quality. Seems like Whirlpool should step up and do the right thing. This needs to be replaced.

I have a Whirlpool Cabrio washer (Model: wtw6400sw2 / Serial Number: cu0271913) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool and I will contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

I had the best experience when I purchased my washing machine and dryer. The personnel were professional and very pleasant. I am quite pleased with my washer and dryer. I have had a couple of minor problems but the warranty that I had on them was excellent.

Ive only had my matching set of Duet Washer and dryer for 14 months when the noise got so bad that we could wash when we were at home. We would start a load and leave. I bought the Repair plus one and Whirlpool and said they would give me $599.00 to replace my machine. I cant buy one for $599.99. They said they replace when I purchased the warranty, but now Im told at 75% of its value because its between 1-5 years old. Now, Ive paid $300.00 for the warranty and will half to spend another $200.00 to replace it. Im frustrated and disgusted with Whirlpool.

I really like my new 5 burner gas double oven gas range made by Whirlpool. Except for 1 minor flaw where the backsplash panel warped at the beginning and was promptly replaced by whirlpool I have had no problems with my range, love having 5 burners and a double oven. Plus the left front burner has a much bigger burner with higher btu which helps water come to a boil way faster than any other ranger I have ever had. That is a real nice feature and I really like having 2 ovens, When cooking on an average day for my small family there is no need to heat up the big oven and the little oven is just the perfect size to bake 1 or 2 dishes. And on holidays when I am cooking for more people or many more dishes I have the capacity to cook more items.

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...

Purchased this Upright freezer model 160NZTQ02 approximately 2 years ago. Freezer had problems maintaining temperature from the beginning. Noticed it freezing up at air vents in back of interior. Unplugged, removed contents, and let defrost by ambient temperature (approximately 4 hours). After using this method for first three defrost periods (approximately two weeks apart) I began defrosted with hair dryer, then moved on to heat gun. Bottom line is this junk wont hold temperature and freezes up every few days to a week. No more Whirpool for me.

Whirlpool Microwave model #GMH5205XVS0 - Same story as many of these other reviews. Similar reviews on Amazon as well. We bought a new house early in 2011 with all Whirlpool appliances. We have gone through 3 magnetrons in 2 yrs. Now Whirlpool wont do anything for us. We will have to buy a new microwave. It just stopped heating all 3 times and the magnetron was replaced. Now it has happened again. Ridiculous. I will never buy a Whirlpool appliance again. This model # should be recalled. Its a lemon and sounds like it could be a danger as well.

2010 upright Whirlpool freezer - Door is totally bubbled in rust. Warranty Plan not covered for this. Whirlpool Corp Serv. Dept said they are sorry but it is not a functional problem. Cost of repairs on 3-yr-old freezer that cost $600.00 would be $732.62. This freezer was rated CR Best Buy in Sept 2009 which was why I purchased it. I paid $81.00 for repair tech from Whirlpool today who could do nothing either. Whirlpool knows that this has been a problem as consumers have complained about this rust in Google, some saying they will never buy a Whirlpool product again. Same here!

We built 8 years ago, with ALL new appliances...All Whirlpool Gold...been very unsatisfied with ALL appliances... Had to replace range and parts for refrigerator..And extendend warranties all nonusable..We live NM off a tarred county road by 1/4 mile...no one wants to even come and look. Not good.

Amazing pice. Would recommend to anyone. The heat is great. The oven is amazing. I got this for my birthday and my kids were helping me to get it and I was so excited to receive it I was crying. Amazing machine, wish I had two. Would definitely buy again. I especially love how clean the oven top looks and how the knobs for the burners are easy to use.

We purchased 2 whirlpool commercial coin operated washer machines and both computer boards had to be replaced twice each - model CAE2743bqo and CAE27438qd.

After less than three months the oven control failed. Local repairman said it would cost $450, better to get new one. Whirlpool set-up service call with their Certified Technician, who didnt come. I had to pay compensation to rental guests in the property who went without an oven for almost a full week. Also had to buy a replacement ($633) to provide a functioning range for these guests and next weeks guests. Whirlpools only response was to offer to set-up ANOTHER service call. I am out over a thousand dollars. I have been a loyal and repeat Whirlpool customer for years, but no longer. What an extremely unsatisfying experience!

We purchased the unit in March, by April it wasnt cooling. In June it shut down. In July after 8 tech appointments and repairs. Whirlpool finally said they would refund my purchase and I should see the money in about three weeks. That would be about a week longer than the refrigerator worked. I dont have the money to just get another one so I guess the family will be without a refrigerator for another month. That means shopping every day for perishable for a family of 10. I would not recommend another Whirlpool product. This is no joke, every time I called them one of the first things asked was Did you get the extended warranty? Why would they ask, sounds as if they dont trust their own product either. This unit was purchase online through Sears.com. Purchase price was $2299.99. Order placed on March 4, 2017.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

We had to buy a new fridge in 2000 because ours broke. Following consumer reports, we went with a side-by-side Whirlpool gold and was it pricey! Within the first five years of its life, we had to replace the fan twice...the bar that separates the fridge and freezer could have fried an egg--it was so hot! When I had to replace it the second time, I pitched a fit to Whirlpool and they could care less! Now I see that the inside wall of the fridge section has cracks forming! I know the average lifespan is 10-15 years but I still will say that I will not buy from Whirlpool anymore! Their stuff is very expensive and it just seems it has too many small things that do not hold up!