When the fridge is running and there is a power loss of about a second or so, the fridge shuts down and will not restart (even after hours). I have to unplug it for a minute or so then plug it back in; it runs fine until the next very short power failure. When we are out of town for a few days and that happens, we come home to a fridge of ruined food and a mess. I have contacted Whirlpool (2 times) and they were no help at all. It seems to me a software change could solve the problem, but they are unwilling to listen.

They will not honor the extended warranty on their fridge which Ive had for less than three years which will not defrost making me lose thousands in spoiled food. Extended warranties are contracts and this company should be penalized and shut down for fraud.

It is my belief that through my experience that most Gas Range manufacturers mainly Whirlpool corporation purposely designs the stove igniter part to fail in 5-10 years. They do this in hope the consumer will purchase a new stove. The igniter in my stove has failed 6 times since I purchased it in 2005. I have had to replace it at my expense each time. The last time it failed, I asked Whirlpool if they would do a good faith gesture and replace it. They very rudely refused. I will never purchase another Whirlpool appliance again and encourage others to follow me. If they give me this much grief over a simple good faith gesture, I can only imagine the difficulties in getting them to honor a warranty claim!

On 3/31/2012, we purchased a Whirlpool refrigerator (model #ED5FVGXWS07, serial #HR14602963) from the electronic appliance store called SuperCo, located at 17523 Colima Road, City of Industry, CA. Within around a month, we noticed that things kept in the refrigerator all showed weird phenomena; raw eggs were frozen inside the shells and ice is frozen on food and utensils stored, not in the freezer, but on the fridge side. At the same time, all food kept in the refrigerator turned bad easily, especially during summer time. Cooked food went bad and had a bad smell within just three days of being kept in the fridge. Also, the ventilator-like part on top of the fridge (the part which released cold air) had ice frozen around it from time to time.Obviously, the fridge was not working, as the freezer was not cold enough and the side was either making food turn bad or causing ice to freeze on stuff kept inside. The temperature seemed to be extremely uneven inside. We then asked SuperCo for repairs or a replacement, but they refused and referred us back to the manufacturer, Whirlpool. Repair services have been called three times on 2012, according to the paperwork records I have: a) on 5/31/2012, bad damper was broken and replaced; b) on 6/7/2012, (according to paper records from SuperCo), replaced parts; and c) on 6/20/2012, turned ice maker off and cleaned (the hand writing was hard to read).Then, around December of 2012, after the services, we experienced another great problem with this fridge again. When ice cream was kept in the freezer, they appear to have melted and my brother suffered from diarrhea after eating the ice cream. The ventilator-like part on top of the fridge still had ice frozen around it. We then took pictures as fresh vegetables kept at the bottom drawer of the fridge had ice frozen on it, too. I finally emailed Whirlpool through their official website on 2/7/2013 and asked for a new fridge replacement based on the Lemon Rule. An e-solutions specialist, Judy, replied that the product was warranted for a specified time period for repairs, not the replacement of the product, and Whirlpool declined my request for a replacement.Repair service was then requested by me for the fourth time, through email. On 2/21/2013, this fourth repair company came and checked the fridge. After a detailed inspection, the technician concluded that some parts of the fridge needed to be replaced, one of the parts called the thermostat. Strangely, after he called his company, he changed all that he said before and claimed that the fridge was 100% working and that no repairs were needed at all. Even when we showed him the frozen vegetables from the fridge side that we got recently, he insisted that the fridge had no problems at all and left.The way Whirlpool responded to my request was extremely disappointing, with their refusal to replace the fridge after three complete repair visits, and the fourth visit changing the inspection conclusion with no reason. Of course, the disappointment is greatest with the extremely bad quality of this electronic appliance. As of this moment, my fridge could still not keep food well and is causing us bad health. I think the only way I could go to now is to take action against the company for the lemon refrigerator, for breach of warranty, and maybe fraud.

We purchased the Whirlpool refrigerator on July 9, 2012. Refrigerator was replaced on August 23, 2012. Since then there have been many, many service calls. I wish I had kept records to be able to tell you exactly how many times, but we purchased an extended warranty. From memory, I can tell you the ice maker has been replaced twice, new doors have been installed for refrigerator and freezer (replacing ice maker a third time), then within the last three months the freezer door was again replaced (replacing ice maker a fourth time). The gasket on the freezer door has been replaced. At one point the refrigerator was colder and freezing and the freezer was not freezing. Parts and pieces have been repaired on several occasions. The inside of the freezer door next to the ice maker is still frosting up and yet again the ice maker is not functioning and needs to be replaced a fifth time. In other words this Whirlpool refrigerator has been a lemon for us. Finally, we figured it out. There is a fairly large gap at the top of the freezer door between the case and the gasket. If you run your hand across the area where the gap is, there is definitely a dip in the face of the refrigerator case where you can see the top of the ice maker. A picture showing the gap is attached. I am not sure that our purchasing a store extended warranty was fortunate or not. My husband has insisted on repairing this thing over and over and over because of the extended warranty. I think repairing it is futile and the only people being punished by all the repair calls is us because we frequently do not have ice, we are losing food because of freezing or not freezing or cooling or not cooling as the case may be. Thank God, the warranty expires in July and we can repair this Whirlpool by replacing it with another brand -- not in any way associated with Whirlpool. If you Google Whirlpool, you will find that Whirlpool is affiliated with almost every other brand of refrigerator and really limits your choices. Based on my experience with this Whirlpool refrigerator, I will never purchase another Whirlpool or any other brand associated with the Whirlpool brand. The myriad of repair persons in my home probably find a Whirlpool refrigerator is job security for them.

I hope the CEO posts this on a giant screen in front of all their employees. The first thing I did after moving into our new home is brag about the American made Whirlpool appliances. Being from the Midwest I take pride in made in the USA product and go out of my way to support homegrown companies. I know that a number of the components in my fridge include the fan that failed after 11 month were most likely sourced and manufactured in China... but that no excuse!! Whirlpool needs to do a better job of QC. You need to be passionate and rigorous with your testing. Dont reduce cost at the cost of your customer base. It is amazing were to the point where we can no longer compete with China in quality.Second is customer service, if you know you cant compete in quality you need to be able to make up for that with customer support. I called Whirlpool and scheduled an appointment the day the fridge quit working. I was upset that it would take three days to have a working fridge but I was understanding. Lucky for me I had an understanding neighbor too. Anyways, when the day came for my scheduled warranty repair I was told that Whirlpool was mistaken and that I wouldnt be able to get it serviced for another week! This is just unacceptable.Right away I called the Whirlpool customer service representative and manager to express my frustration with this error. They were polite and both agreed with my frustration. It also sounded as if they also didnt understand why their own company was doing such a poor job addressing repair issues. They made it sound like this was a common problem of people getting overbook at repair service providers. Again another fumble. Bottom line, due to my position, I dont really have a choice but to wait another week for a repair. Take note: Every time you lose a customer like me this you lose 10! I will now go out of my way to tell people about my negative experience rather than my positive. So disappointed.

My old dishwasher washed much better than this one. For one thing, I do not think having the silverware basket in the door is a hindrance more than anything. For one thing, the silverware does not always get clean. Even some of the dishes do not get clean. I think the engineering of the dishwasher is poor. When you pull the bottom rack out to put more dirty dishes in, it gets caught on the silverware that are in the silverware basket in the door. Makes it very difficult to get the bottom rack out or in. I have no gripe on the size of the dishwasher. I would just like it to wash the dishes and silverware clean. The appearance of the dishwasher is good but that doesnt clean the dishes. I am more than satisfied with the appearance of it. I do like the buttons being at the top of the dishwasher so that a person cannot bump them when it is running. I just think the design of it could have been much better. My other dishwasher had the silverware basket inside on the bottom rack and I really liked that and if I ever buy another dishwasher, I would make sure that it is inside the dishwasher. I dont believe that Whirlpool is the company it used to be. I have an oven that has been nothing but a problem for me and it is a self-cleaning oven but I cant even use the self-cleaning feature because it blows something in it and it doesnt get hot and clean it. Have had it fixed twice and the company that sold it to us will not even talk to us about it. Im not sure that I would buy another Whirlpool appliance of any kind again.

I have a Whirlpool Cabrio washer (Model: wtw6400sw2 / Serial Number: cu0271913) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool and I will contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

Bought these Whirlpool Cabrio Platinum combo about three years ago, nothing but junk from the get go! Washer never gets clothes clean, towels always come out smelling mildew and sour no matter what liquid soap you use Tide, Gain, whatever same results. Plus always mold coming from inside tub and yes we use refresh weekly and wash it out on refresh setting. I’m so tired of our towels smelling sour but can’t afford to buy new washer and dryer living on fixed income. If I could these would be in the recycling yard now. From everything I’m reading all new H e machines are crap and energy efficient my foot. I wish for my old style washer and dryer. WHIRLPOOL YOU HAVE LOST A LONG TIME CUSTOMER!

Thank you EPA for requiring water limits on manufactures of washing machines. As a result, I am forced to use the deep water and extra rinse functions to get clothes half way clean. So much for saving water! This Whirlpool Cabrio machine cost way too much for such lousy results. Additionally, I have to purchase a special product and clean my machine every month or two. Ridiculous!! I yearn for the old days when I could wash my clothes and they would actually come out clean.

We bought a new side-by-side refrigerator (GSF26C5EXB00 26cf) with water and ice in the door. We have had to replace the built-in water filter every two months at $30+ per filter. This is unacceptable. We just want to know what to do to fix this problem. There is only one person who uses the ice maker, and no one uses the water in the door.

We purchased an electric range model WFE371LVQ O in June 2010. This range is only used during the winter months in our vacation home. In January 2016 the oven turned on by itself. The control panel was replace. It happened again on 1/25/19. IT IS A FIRE HAZARD!! Thankfully we were home both times. The only way we got it to turn off was to flip the circuit breaker. If this would have happened when we werent home and a fire started and it killed our dogs I have no idea what I would do. Im not even attempting to have the control panel replaced again. Well be buying another brand. I DO NOT RECOMMEND THIS TO ANYONE. The company must have known about the issue because when we called the first time it happened, which was several years PAST the warranty period, they didnt hesitate to do the repair free of charge.

I bought this to provide A/C to our bedroom during a power outage by use of our Gasoline generator. It is very quiet and provide a very cool air flow. The double vent pipes make it efficient and more than capable of cooling out 15 X 25 foor bedroom. Whirlpool has 28,000 employees in the USA.

I have purchased a 3 door Refrigerator of Whirlpool on 27th October, 2014 from Sargam India Electronics Pvt Ltd. Now my refrigerator was not working properly. So we registered a complaint regarding same. On 3rd July your one executive came and he asked that its compressor is not working and we have to refill gas also and charges will be 2000 rupees for Gas and compressor is under warranty. Then on 4th July your another executive came with compressor and he worked for 1 hr on fridge then he asked, Compressor is not taking load. My senior will come tomorrow, mujh se nahi ho raha. On 5th July morning we got a call and he asked that he will come till evening. Now we got a call. They are asking that its not under warranty. Hum log paso mai dhik kar sakte hai. When purchased in 2014 last ist thing its under warranty only they have told us for 10 yrs. And we have purchased 4 yrs + back not 5 yrs completed. Apart from your customer service guys we never shown this to any one else as its under warranty, I am clearing this thing on prior notice. Senior are not taking action. They are asking we can do it in money. They are asking, If you want to go consumer court you can go.

I purchased this Cabrio washing machine in December of 2016. I have had a huge amount of trouble with the soap not washing out along with it tangling my clothes. This has to be the worst machine I have ever purchased.

Whirlpool Refrigerator: Model # WRT111SFDW - We bought this frost-free frig. in Feb of 2016 and this Feb. before the year was up, it started freezing up. I called the Co. and they sent a young man to my house to fix it and he thought he had. Well 2 wks after that it started freezing again and I called the Co. again and the same thing happened again and this was after my warranty had expired. Well then this young man came out and replaced the fan and a heating rod I believe to help it to stop freezing. Well 2 days ago it started freezing up once again. Im disabled and live on a fix income so now Ive got to figure out to get me another frig. And it WILL NOT BE A WHIRLPOOL REFRIGERATOR. But kudos to the Co. and the young man for trying to fix it even though it took 3XS and still not working.

Bought this washer and dryer on sale at HD. The washer hasnt worked from the beginning. The clothes dont get wet because its an HE. I have to add buckets of water to even get the clothes wet enough to wash. The clothes come out with a residue on them. We use liquid HE detergent. It appears Im having the same problem as the majority of posters here. I will NEVER buy another Whirlpool appliance. There should be a class action suit to get Whirlpool to respond.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

I purchased the Cabrio washer and dryer 4 years ago and had no problems until recently. The motor and the harness broke and the cost to repair was almost as much as a new washer. The repairman told me that this is a common problem with all washers that Whirlpool makes as they have the same motor and harness. He gave me a list of all the brands that they make and suggested if I buy one to get an extended warranty. I would not recommend anyone buy an appliance from a company that continues to manufacture faulty products. I wonder if they own the extended warranty company?

I bought a Whirlpool Gold Series Microwave, model # WMH76718AW, on 2/19/13. It stopped working 1/25/15. It doesnt heat food anymore. I also have a whirlpool dishwasher that doesnt clean dishes. Whirlpool products are junk. Whirlpool customer service is awful. The cost of fixing this lemon and then buying an extended warranty for the repair (which they recommend) will make this a $1000 piece of garbage. They dont stand behind their defective products. Ill never buy another one again.

Purchased 2 sets of the full sized refrigerator and freezer combo. First was 2005 and second was 2015, both new build homes. We had a few probs with 1st set but the 2nd has been a nightmare. Just like others we have lost time and food because of the constant problems. Avoid @ all costs!!!! Apparently they only care about lining their pockets and not the consumer.

I purchased Whirlpool only front load compact washer in June 2015 and lasted only a year before the door lock broke and getting F6 error that means mother board to be replaced. Whirlpool warranty department (AIG) did not bother to do a complete repair and offer buy out at a 75% of my purchase price. My five year warranty premium cost was not refunded. I do not recommend this model be purchased by anyone. Whirlpool washes its hands on the quality and reliability of its product in US and that is a shame! A service life the unit should be at least 9 years with affordable maintenance cost.

I purchased a front load washer and dryer brand new. The washer is under a 2-year warranty on all parts and labor. Since I have purchased them, the washer has had to be fixed on several occasions. I have had 10 parts replaced and had to be out a washer for a month at one given time. I have had the repair company email me all the parts and services that they have done. All I want is a new washer! I have argued with Georges Appliances on several occasions because I believe they sold me the obviously faulty washer and I dont believe that I should be responsible to have to figure it out for myself. They should be responsible to provide me a new one. They told me that I had to contact Whirlpool in order to receive a new washer. Please contact me asap.

I purchased a 40 gallon water heater at Lowes and installed about 3 years ago. A couple of weeks ago, it got an upper sensor failure code on the gas valve. It would heat by resetting (turning valve off, waiting a minute and then lighting) but after a few minutes, it would fail again. I called the customer service and they mailed out a new upper sensor. When it came a few days later (I paid for shipping), I installed it but the same failure code. Again, the only heat I could get was by resetting the valve several times before a shower. I called customer service again, told them what I did and they said, Oh, the problem is the gas valve then. So they mailed out a new gas valve unit. It then came a few days later and I installed it according to the enclosed directions to the letter. Still got the failure code and still had to keep resetting it to get any warm water before a shower.I called customer service again, told them what I did and he said, Well, did you flush the water heater with apple cider vinegar before you installed the new gas valve? I said, No, it wasnt in the enclosed directions to do so. He said, You should have done that and it would have worked. I will send out a new gas valve. At this point, I blew up. Two weeks with no reliable hot water. I told him I want a new water heater and he refused. I asked to speak to his superior. He said no. Dont ever get a Whirlpool product. Some other crappy company builds these turds.

GX5FHDXVY04 French door fridge. Ice maker backup issue - which cause water to build up and leak out of fridge. Fix was a known issue with a rubber grommet - $100.00. Fridge stopped blowing cold air - control board - $293. Fridge stopped blowing cold air again! Getting Nowhere with Customer service... Whirlpool used to be a great brand. They have lost me as a customer, and by the looks of this board, Facebook page, I am not alone!

This is the worst product (Whirlpool Cabrio Washer) I have ever purchased. I paid $999 for it new. I had to have it repaired at the cost of $500 at just two years old. My sister bought and had the exact same repair needed. I used to trust Whirlpool but not anymore. I wont buy Maytag either since it is a Whirlpool product as well.

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

Our 3 1/2 year old dishwasher is falling apart. First the left slider broke on the top rack. We ordered a replacement part ($74) and when ready to install, discovered the right rack was also falling apart. At that same moment, the rollers fell off the bottom rack! It seems the plastic parts cannot tolerate the heat in this dishwasher (just a guess). We’ve returned the new replacement part and are shopping for a new dishwasher. It will not be anything from the Whirlpool line!

Washer has rusted out after only four years. I bought my set from Sears, and thought I would get good use out of it for many years; but I am experiencing rust falling from around the rim of the washer. Very dissatisfied with the product, I will never buy another appliance from Sears again. I have always used Sears appliances but after this experience I would not recommend Sears to anyone. I was told that the warranty was for one year, and the rust would not have been covered anyway. Very Dissatisfied Consumer. I thought Sears would stand behind their products. Yea, right.

My dishwasher is more than five years old. The water jets need to cleaned regularly. A little noisy but I can chalk that up to age. I use 1 or two packs of detergent. Sometimes, if I don’t pre-wash, I need to run through the cycle.

Our Whirlpool dryer broke less than 3 months after we bought it. We called Whirlpool and spent more than 2 hours on the phone. They sent someone out and that person told us he couldnt fix the part that was broken. He gave us a phone number to call and we called and spent another hour on the phone after which we were told to call Whirlpool back. We called them on 3 separate days and spent hours on the phone trying to contact real people. After another week (during which time the dryer went out of warranty) we had to call someone to fix it. After that we spend a month calling and emailing Whirlpool to get reimbursed for the almost $400 we spent fixing it. No luck. We were told that it was out of warranty and we didnt use a Whirlpool technician. I was hung up on, given the runaround through phone menus, continually told it wasnt the correct department, and finally that Whirlpool doesnt cover it. Bottom line is...never buy Whirlpool.

Model # WMH 1163XVQ-1 manufactured 2010 however I purchased and installed it in July 2011. Noticed a small crack at the base of the handle about a year later. Within the past couple of weeks cracks are appearing everywhere including around the handle, the entire exterior frame as well as interior frame of the door. Neither my wife nor I slam the door or mishandle it to cause this damage. Called Whirlpool this week. Bottom line is that it would cost nearly as much to get a new door as to buy another microwave. This is an over the stove model. My previous microwave was GE and lasted over 15 years. Wont buy Whirlpool again.

It has been a rude awakening, that Whirlpool is a substandard company. I have gone through 3 refrigerators under the label Kenmore, Whirlpool & 2 1/2 days ago Maytag. I purchased a Maytag 9 years ago and it is still working fine, and even cools a bit too much. Now mentioned labels are under Whirlpool; Since Whirlpool bought out Maytag in 2006, Whirlpool turned Maytag into a sub standard product company. They are spuming refrigerators with defective thermostats. Just think of it, I am one customer that have had the same issue with 3 REFRIGERATORS UNDER 3 LABELS MANUFACTURED THE WHIRLPOOL. I just called Maytag, and when I tried to make sense of the name of either Daren, Karen or Taren, ** hung up on me. I then called Home Depot online major appliances & ended transferring me to WHIRLPOOL!My Maytag refrigerator was delivered 07/25/17, after less than 24 hours, I had to move the settings to 4 from 3 for the refrigerator. She said that if the refrigerator cools enough at 4 then there is nothing wrong! Nothing wrong! To be substandard, in my book its plenty wrong. They have no business sense nor customer service sense. I will buy another refrigerator or appliance from any Whirlpool labels when hell freezes over! For them to accept substandard parts, probably foreign, it is not acceptable in CA nor the USA. Since; since this is a foreign owned company, I pray they will be a company not doing much business in the USA unless the measure up to our standards. Since; going forward we will make American and Buy American!

My wife and I purchased the Whirlpool calypso washer and dryers and have been regretting ever purchasing a Whirlpool product. Not more than a year and a half after spending thousands of dollars on their products the troubles started. I called the company and they sent someone out to look at it for repair. He vacuumed out the lines and kept restarting it over and over and eventually it started working again and they charged a hundred dollars and something and said there most likely be more problems since they have many calls on this issue. Sure enough it started again and just kept retrying it over and over to get it to work again as well as vacuumed the lines again like he did. Now its at the point it will not work no matter what. It just keeps flashing LD and shuts down. So I did a online search for other consumers having the same problem and was shocked by the amount of the same problem with others (search this model flashing LD and you will see for yourself). When I contacted Whirlpool they played dumb and lied right thru their teeth saying they have no issues with this model and refused to do anything. I have since learned there has been court cases where the courts ruled against them saying that it was defective and had to notify consumers which they never did. Even when the repairman came out nothing was said. I have since learned that all they did was changed the name to a different model which is having the same problem (no kidding!!) and continued to rip the public off in the name of CORPORATE Greed!!!!! I advise everybody never to purchase a Whirlpool product ever again and maybe we can bankrupt them and put them out of business where they belong. All the customer service agents deserve to be unemployed and suffering after long waits on the phone and then lying straight face to the consumers. Pure evil!!!! We all have to stick together and bring these criminals down. How can they say we have no issues when a simple search of Whirlpool Calypso problems with draining and flashing LD and shutting down. There are thousands of people complaining and no action is done. Shame on these people and their souls are lost forever. Never buy a Whirlpool product and tell everybody you know to stay away! They should have their ** and/or ** cut off and have to suffer the same way the struggling consumers are after scrounging up thousands of dollars for a 200-pound metal paper weight that aint worth a damn!!!!

I purchased my new Whirlpool Cabrio Top Load washer to replace a Maytag that had finally given out in the summer of 2012. I wish I did more due diligence, but with a toddler and a newborn, I needed a washer asap. I severely regret my $800 purchase from Sears. It is now February 2013 and the machine basically only runs on two cycles - Casual and Normal. All the others stop in mid-cycle. Sometimes, the items are still dry or partially wet so I need to switch to another cycle to complete the wash. This is not good for Delicates or when I wash Whites, Heavy Duty or Bulky items which is one of the reasons I purchased the model. The cycle stops when the items are soaked with massive amounts of water. So I then have to turn it to the Drain cycle and start over. After a day of washing one load, I couldve done it the old-fashioned way in my utility basin sink and hung it out to dry ... I dont have the time for this. I am going to make a formal complaint to Whirlpool and to Sears. I cannot keep spending nearly $1,000 for items that break within a year. These companies should be ashamed of their lack of quality. I shouldve gone with the Electrolux and just dealt with the price tag - I wouldve been much happier.

Bought all Whirlpool appliances for my home and the dishwasher doesnt work right and all that they can tell me is its not even 7 months old. They dont have any repair technician around where I live so Im on my own to get it fixed. So much for getting your moneys worth.

I purchase December 2019, I had my previous stove for 20 years and wanted a new fresh look. I purchased the stove during a Black Friday sale. Started having problems with the door not closing. Customer service hold time took days and hours of hold time. Took 3 weeks to repair. Now seeing and hearing sparking and its week before Thanksgiving NO STOVE AT ALL. DONT BUY!!!! What happens when warranty is over????

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...

My 4-year old water heater has upper/lower sensor issues for the fourth time this year. The rep was supposed to send replacement parts to arrive today (day four with no hot water), but the wrong ones were shipped. A different rep called and offered to exchange the unit for a new one. The expense to me will be $350-$450 for the plumber to uninstall my unit, take it to Lowes and bring the new one back to install. The plumber suggested I take my $450 and just buy a new non-Whirlpool unit. He knew immediately that I had a Whirlpool hot water heater because its the most common repaired vendor. Whirlpool should be covering this expense for re-installation of their inferior product. Poor customer service. Day 4 with no hot water during the holidays with no solution in sight short of me purchasing a new hot water heater. Whirlpool finally got the right parts to me and I paid a plumber $190 to install. One week to the day later, my pilot light will not stay lit. No change in ventilation since it has been installed. I will say I have been dealing with their rep Chris on the phone who is extremely nice and I feel sorry for him. But we all have the exact same issue which is not being resolved.

AquaLift cleaning system does not work. My oven was barely dirty and I had to scrub with the special sponge to remove baked on food after I did the cleaning system twice! Rust is also showing up on the drawer which they refuse to repair because it is ONLY COSMETIC! Stove is 16 months old.

Whirlpool Washing Machine Model WTW4950XW0 - This washing machine was purchased as a gift by my father. We have owned this machine for about 2 years. I am very disappointed with the quality of this machine. I have 3 children and several pets. I use my machine a lot and need a quality item that will last. This machine is not that item. Within a few months, the machine was off balance and bolts had to be tightened. We have had problems with the belt, bolts coming loose and the machine not draining.More recently, the machine has become very loud... For approximately the last 6 months. My husband has taken the machine apart and looked for anything to be wrong with it and has found nothing. Now the machine is not running. I will turn it on and it fills with water and then stops. I will clear it out and restart it and it does the same thing. Another issue has been with spinning and draining. The clothes are soaking wet even after the drain/spin cycle.I have researched what could possibly be wrong with this machine and have found a vast number of items that could need replaced. With the money I have already put into fixing this machine in the past and the amount it will cost to fix it this time, I believe I will be further ahead if I buy a new machine made by a different company. I will not be buying a Whirlpool product again.

We purchase a Whirlpool duet washing machine 4.5 years ago. Just recently the bearing went on the machine. Took the machine apart to fix and was originally told new parts will be delivered free of charge since this is a common occurrence. 5 weeks later and several phone calls, we were told the part is on back order and they do not make it anymore. Then they send an email to keep us as customers for 15% off. Ridiculous. How do you go from getting parts for free since it is a frequent occurrence to not having the parts at all and getting 15% off for a new product? Why would I want to stay with these false claims? Talk about a slap in the face!

This is a good size fridge/freezer with double doors 25.4 cu ft, its given us good service for 13 yrs without any problems. My only complaint that I wish it was more quiet. (Whirlpool brand) double doors, ice maker w/ water and lights.

This Whirlpool refrigerator/freezer Model W10314956B was purchased from Lowes on June 29, 2012. Recently noticed rust appearing under ice/water dispenser tray. Requested warranty service, but was told the problem was considered DUE TO WEAR & TEAR! TOTAL COP-OUT! There are NO MOVING PARTS in this area; how can there be WEAR and TEAR? To my mind, this can only be charged as SHODDY MANUFACTURING or INADEQUATE QUALITY CONTROL by the manufacturer.This appliance is only 6 1/2 years old! Consumers expect refrigerators to last much longer than that. The only possible cause for this problem is as stated above: poor quality control by the manufacturing plant, and I completely discount being told the problem was due to WEAR and TEAR! I will think long and hard before I ever even CONSIDER purchasing another Whirlpool product, and maybe YOU SHOULD TOO!One issue that keeps gnawing at me is HOW, since this is supposed to be a STAINLESS STEEL refrigerator, can it rust? The best answer I found on Google was that its likely due to insufficient chromium in the mixture of metals used to make stainless steel. To me this continues to point to shoddy workmanship at the manufacturing plant. I have pictures of the problem, but for some reason Im unable to copy them to this complaint. Probably because Whirlpool is afraid of pictures that confirm their shoddy craftsmanship!

I had the best experience when I purchased my washing machine and dryer. The personnel were professional and very pleasant. I am quite pleased with my washer and dryer. I have had a couple of minor problems but the warranty that I had on them was excellent.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

40-gal gas water heater - I own several rental properties and unfortunately put Whirlpool water heaters in them when the old ones go. It is because they are at Lowes and they are cheap. Today, another call came in from a tenant with no hot water. I called customer service and they determined I received the repair kit from an original design defect from back in the middle 2000s. Now 3 years later, it goes out again. Because I have already received the conversion kit taking thermal couple threading from LH to RH, I needed another part number to repair for a grand total of $160! The same part before the conversion kit was $60. I will never buy another Lowes/Whirlpool water heater for as long as I live. I own a hundred rentals and Whirlpool will never again see another cent for the junk water heaters.

My hot water tank wont stay lit. I replaced the heating element, and the thermo couple. It will light up now but it only stays on for about 10 minutes.

I purchased this Whirlpool washing machine in July 2009. The repairman just gave us a $1400 estimate for repairs due to failure of bearings. This is an energy efficient, expensive appliance that we expected to last for years and we feel that 2 1/2 years of service is unacceptable. We did not purchase an extended warranty and Whirlpool said they would help with the cost of parts - not labor. We cannot afford to repair a lemon and so purchased an LG front-loading washing machine today. Hopefully we will have a better experience with LG as we will not be purchasing any more Whirlpool appliances ever.

I purchased a high dollar built in side by side fridge with custom panels in 4/2005 and had my first service call in 5/2005. Since 2005 we have had 11 service call mostly for defrost failures and over temp. readings. From 2011-11/20/2013 we were issue free then the fridge over temp alarm sounded and we could not hear the fan motor. We had the certified tech come out to evaluate and found that the main control board needed to be replaced. Kitchen Aid/Whirlpool no longer make this item and forwarded us to Core Centric solutions to have a new one built. After speaking with the certified tech who had been out to service our fridge 11 times he informed us that these boards in his experience have never lasted more than a year. We spoke with a customer service rep a Kitchen Aid and asked about a prorated discount on a new built in fridge and she said it seemed reasonable but after checking for authorization informed me I needed to have the board rebuilt at my own cost and that even though this typically takes about 4 weeks to build the fact that our family would be without a fridge is not Kitchen Aids problem. 6/20/2005-over temp/not cooling call (replaced defrost thermostat) 9/2005-over temp/freezer iced over in bottom (freezer decided and drain unclogged) 10/05-over temp/not cooling (replaced fan motor) 9/06-over temp/freezer iced over in bottom (drain line decided, kitchen aid had no advice on how to fix) 10/06-over temp/not cooling, ice build up (whirlpool recommended replace heat kit and bimetal) 11/7-over temp and ice buildup in freezer with leakage (adj to drain pump and defrost drain basin made) 11/07- over temp and freezer icing over (whirlpool sent out a new heater probe) 6/08-over temp and ice buildup (bimetal and foam block replaced) 10/09-over temp, lights and motor shutting on and off (replaced defective board) 10/09- fan making excessive noise (ice buildup found on evaporator fan)11/13-over temp ice buildup in freezer, burning smell from fridge and no air movement or cooling in either compartment (need board rebuilt as on 10/09)Board no longer available from whirlpool, must be custom built at owners expense and will take up to 4 weeks. D/t continuing issues and whirlpool not willing to help the customer with replacement I would highly suggest no one buy a Kitchen Aid fridge.

On July 19, I was forced to buy a new washer. Bought a Frigidaire which, when connected to the water supply, started immediately dumping water into the drum. Sent this defective washer back to the retailer and chose a new Whirlpool. O-M-I-G-O-S-H! It was delivered on 25 July and despite having 4 temperature settings, it only worked on either hot or cold AND you could never tell what temperature was going to be chosen by this computerized wonder. I repeatedly called Customer Support and received three different answers on what temperature was considered warm. The answers ranged from 65 to 102 degrees. Also, you could open the lid when the water was running in, which washers are no longer supposed to do. Whirlpool then arranged for A & D Service to come and repair my NEW washer and scheduled an appointment for a week later. I was forced to call that company to find out if they were even coming. When they did not show as promised, I cancelled the appointment and called Whirlpool to ask for another service company. They then scheduled me for two weeks later (now August 30th). The guy did come and told me there was user error - I had used too much soap as this was an HE washer. I asked him to show me where on the appliance and in the owners manual that it stated the washer was an HE. He couldnt find it either and said he would replace the computer and the door lock because his computer found that the washer was hit and miss on anything it was set on. At any rate, it is a little over a week later and I have heard nothing from the repairman and, of course, no follow-up from Whirlpool. Do not make the mistake of buying any Whirlpool product, and that now encompasses names such as Maytag, Amana, Jenn-Air, Kitchen-Aid and many more if you want to be assured of a quality product and excellent customer service. What if this had been a refrigerator? The whole debacle has been a nightmare. Wish I had bought a GE!

I purchased a washing machine FS65 on 10-30-2005. In Oct. 2009, my washing machine developed some fault so I contacted the Whirlpool service center and got it repaired. Again in Dec. 2010, the appliance became faulty and so I contacted the service engineer to attend to the machine. He repaired it and I paid 2500/-. But the very next day, my appliance showed the faults again. It was rectified with replacement of PCB and I was charged 2786/- on 01-20-2011. Again on 09-04-2011, the machine became defective. On the call to service center on 09-05-2011 and attended by engineer on 09-06-2011, I was informed that PCB is defective. I failed to understand that the PCB replaced in January was of what quality that it has to be replaced now after such a short span of time. I feel that this is clear cheating with me.

My dishwasher is 4 months old and is having some electrical issues. I have had to call into customer service 3 time to try to get a service call. Two of the service calls did not show up. To this Whirlpool said it was not their responsibility. From my experience Whirlpool does not care that the service calls are weeks out, or that the dishwasher does not work.

My Side-by-Side Whirlpool fridge which I bought very expensive in Colombia one year ago had the glass shelves totally cloudy and foggy. You could hardly see what was inside. 8 technicians were sent through the authorized center to meet warranties to check the fridge. The first 7 technicians(!) did not have a clue of what the problem was. After many calls, they sent a supervisor who discovered the problem and finally, after 10 months of this battle, they changed the fridge for a new one. But guess what?! I received the new fridge 2 weeks ago and the new one has exactly the same problem. I am very disappointed and I do not know what to do at this point. Going through the same process again makes me sick but losing my money and all the time invested in this product makes me furious. Is there any way that Whirlpool can help me through this forum?

I purchased a Whirlpool gas water heater for one of my properties that developed an issue outside of the warranty period. My initial CS complaint is with Whirlpools IVR system, which was far less than a desirable experience. After tricking the system, a CS agent answered promptly but was not able to address my concerns. I asked to speak to a supervisor and received a return call from Chris within minutes. I found Chris to be patient and understanding of my issues. Chris promptly assisted me with my issues and offered an equitable resolution. Chris is whats right with American companies and domestic customer support.

We purchased a side by side Whirlpool refrigerator/freezer in June 2011 and have had nothing but problems with this piece of crap appliance. Ice maker has been repaired 3 times, water line clogged twice because of freezing and thawing. Now the machine only cools both sides to 45 degrees F. I am having a repair person come out on Monday to tell me what is wrong but I am so upset with the poor workmanship of this product I dont want to put another dime into the repair. We paid $1100 on this and have paid at least $600 in repairs over the past 4 years!! I agree with all of the other comments on the poor manufacturing choices. We had a GE prior to this and it lasted 10 years but we had the same issues. Repairing it every few years. I am not sure what brand to purchase next. If anyone has a suggestion I would be open to it.

My Whirlpool microwave has been great. Just the right size for my family, with enough settings that it wasnt complicated to use. I found it was very useful with different recipes that I liked to make. I always used it whenever possible to cut down on my cooking time because time is something we dont seem to have enough of. I have baked a lot of different items in my microwave, chickens, all kind of casseroles, cakes. You can even scramble eggs in this one!! It keeps dishes warm until you decide to serve it which is a plus because all microwaves do not have this option. I believe you will enjoy it too!

I bought Whirlpool refrigerators around one and half year ago. After 1 year the light of refrigerator was broken. I was contacting customer service and arranged the fix. However, the contractor never showed up. After I making the call several times, I gave up finally. The repair is really bad experience!

My double oven is less than 2 years old. I just used the self-cleaning feature on the bottom oven and now it wont work at all. I understand that this is a common problem with Whirlpool ovens and I will never buy another Whirlpool appliance again. What a piece of junk! I have used self-cleaning on my ovens ever since they were invented and have never had a problem before.

It’s just a month old not even - and the dishes are not coming out clean. The cups are stained and I don’t feel it’s clean as it should be given it’s a brand new machine. I would not recommend this particular brand in Dishwashers.

My Whirlpool dishwasher is used 2-3 times per week. The interior has more than adequate space for a full load of pots, plates and utensils. A normal cycle is used and the washer is essentially very quiet. Dishes/glassware always come out spotless and squeaky clean.

We purchased a new Whirlpool dishwasher in June of 2014. By February 2015 the racks were rusting. I called loses warranty and they referred me to Whirlpool since it was still under a year old and covered by the manufacturer warranty. They said no problem and would have new ones sent out. Three months later I still did not get them. I called them back and they said that they were not covering them due to rust being normal. This is the absolute worst customer service and it says a lot about how Whirlpool stands behind their products.

I bought new and both have broken over and over. The oven takes forever to heat up. The fridges ice maker broke and then the defroster in the fridge side broke. Dont buy Whirlpool.

Overall, I am happy with my Cabrio BUT we purchased a Whirlpool WTW7000DW0 Cabrio top loading washer w/ electronic touch panel in May 2016. We experienced water hammer from day one. I finally had enough yesterday and knowing that the plumbing could be suffering (15 year old condo), purchased 2 Sioux Chief MiniRester, Model 660-H arresters (Lowes at $9.99 each) and had a plumber install them today. I could have but am nursing a fractured rib. Long story short, they work perfectly. There is NO indication elsewhere in the unit that water is even entering the tub unless youre standing right beside it.Ive been told that hammer problems exist in ALL high efficiency washers, all are prone to this problem. I was also told by a Whirlpool support person that the Cabrio is a Samsung design and the pulsing of supply water off and on, over and over is normal operation. If I had been informed when purchasing that hammer is a common problem, I would have installed arresters from the get-go. At the very least, manufacturers should include arresters as a part of the sale; installers should make sure that every new installation includes arresters. All told, I am out just under $200.00 for new technology that really could have been engineered out in the beginning.

We purchased 6 six appliances for our home just over one year ago. The initial problem with the washing machine literally took ten home visit to resolve with the final solution being total replacement. Far too many days away from work. The laundry appliances have a loud beeping noise that goes off with the slightest contact, annoying and designed to be eliminated or muted. Today we discovered that the water filter in the fridge is single sourced at over $50 with shipping, which seems usurious at best. Will look elsewhere for the next house/purchase and NEVER buy from this company, including their other brands...Kitchenaid, Maytag, etc.

This $1,000+ Whirlpool Cabrio washer high-efficiency machine should have lasted between 10-15 years, not 1, not 2, not 3, not 4, not 5! To expect less is to fall for the consumer cave in - where you just give up, give in and buy another. The Whirlpool tech just told the appliance repair guy that was here that the repair would involve a recirculating water pump and a bearing, and would cost $481 to repair. The appliance repairman said he is not in business to condemn appliances, but said he has a Kenmore top loader at his house. Simple, no electronics and less things to go wrong. Well after researching brands and reading reports, I thought I was buying a machine that would last at least as long as my second hand Maytag. Whirlpool has not heard the end of me. I have heard several other people say the same thing. Repair bills are huge and machines do not hold up. So much for buying quality. Now Im going to contact the MA attorney general for the states implied warranty, which means if you spend your money on any appliance, that appliance has an expected lifetime of service. A $1,000+ machine is not expected to fall apart after a few years.

I have a Whirlpool Duet front loader. Sick of it since I bought it! Not enough water to wash & rinse clothes. After consulting sites on internet, husband decided to try adjusting part. He just took off the 3 screws & lifted top off. On the outside part that has a white plastic housing, he turned the longer screw 2 1/4 times clockwise. EUREKA! We have more water! You may need to start out adjusting 1 turn & work up till you see a water level you like. Just dont let the water come over the wide rubber water guard.

I placed a service call for a high pitch sound that emanates from our new Whirlpool refrigerator MD#WRF990SALM00. It is hardly perceptible although hurts my wife and Is ears. The technician was courteous and efficient although said that the sound was typical of this model. He did find another issue with condensation forming at the top and returned with the repair part in a timely manner. I placed another call to Whirlpool whom suggested that I order a different authorized service company to investigate although if the results of the call was that it is a typical sound of this model that there would be a service call charge. I will most likely order this service call in the future although I will wait to see if there are any similar issues that arise. If you experience the same problem with your Whirlpool Appliance please leave your experience. Thank you.

Just cleaning the outside of our piece of ** oven. Must have hit either the on or off button to lock because the damn thing locked. Tried unplugging it, pushing all the buttons suggested on these websites, etc. Hell, even tried to call Whirlpool, where I just talked to a computer. Lesson learned: Whirlpool wont get our business again. Period.

Purchased Whirlpool Duet wfw9550ww00 in 2012 from PC Rich, who purchased machines in 5/11. Product stopped being made 5 yrs prior. Of course I did not know until my washer went and had service come to my house. He explained prior information, looked at my machine for 2 seconds and said someone put in a heavy load that machine was not able to handle and 2 belts broke and guts of machine are destroyed. Its a $799 fix, not including labor, youre better off buying a new machine. How does he know thats the reason for breaking??? The machine is 2 years old, not a scratch on it!!! Unbelievable!!!! Then states thats $114 for the service call. $114 for 2 seconds!!! Im absolutely furious!!! Whirlpool has a new program (if it helps anyone), if your machine is fairly new they will give you a invoice for 1/2 off a new Whirlpool... Take it from there. There should be a tremendous action lawsuit, look at all these complaints...

Whirlpool side by side refrigerator/freezer Model #GSF26C5EXB. LESS than five years old and the ice maker is not working! Bought at Lowes. Great service. Out of warranty now. Lowes sent a repairman and it has to be replaced. I called Whirlpool and they said sorry. THATS IT? Ice makers dont ever last five years now? Unreal!

I Wish I had reviewed this refrigerator sooner. I bought a Whirlpool side by side refrigerator with ice and water dispenser in the door in 2016. Problem #1: Water leaks from the water dispenser and dribbles down the front of the door. I am as vigilant as I can be about wiping up the spills, but over time it has left a water stain. Stainless steel is not stainless! Problem #2: The freezer is too narrow. Too many frozen items that come packaged in boxes have to be wedged into it or stood on end. Problem #3: Ice cubes sometimes randomly drop out of the dispenser and melt on my hardwood floor. Problem #4: Even though the water is filtered, mineral deposits have built upon the well that collects the drips and I have yet to find any product that cleans it. It looks horrible and filthy. If Id had any idea how awful this appliance would look after just a couple of years, I would have been in contact with Whirlpool immediately.

Bought this new in Oct 2012. A week back stopped working. After a week found out it needs new compressor and will cost 1,096.00. Paid 2,100 for this new and now need to buy another fridge but not this make.

Ran Aqualift self cleaning cycle 4 times at 40 minutes and only bottom was cleaned, sides are still spotted and the rear wall still shows a heavy spotting. My stove is less than a year old. My prior stove with self clean at a higher heat was great, when done only had to wipe out!

A little over one year ago, I bought this model from Lowes. Shortly after installation, the ceramic coating on the floor of the bottom oven cracked and shattered. I contacted Lowes... No help whatsoever. I then fought with Whirlpool for weeks until they agreed to replace the unit. Seven months later, the floor of the bottom oven, once again, cracked and shattered. I am now in another dogfight with Whirlpool. This appliance is garbage and Whirlpool does not stand by their product. Do not buy any Double Ovens from Whirlpool. My next step is to organize a class action lawsuit.

I purchased a refrigerator from this company Model #WRF989DAM. It worked for only 14 months. I had service people come 4 times to try and fix it, called customer service and was suppose to get a replacement, paid $300.00 for a different model, been 49 days and still have no refrigerator in my home. Had to go out and buy my own replacement. I have called and sent emails with no response of when I would be getting the replacement.

My $800 Whirlpool Cabrio top loader does not rinse the soap out of the clothes. Nor does it even get the clothes completely wet. After the final cycle I have soap scum in all the wrinkles of the clothes. Most dissatisfied purchase I’ve ever made. The one-star rating comes from the pretty blue digital displays. I’ll be purchasing another; this one goes to the dump where it belongs!

Bought this from Lowes in 2010 with the 12 yr extended warranty. Have not been able to keep it lit. Takes 4-10 days for repairman just to LOOK AT IT and then he usually has to order a new control valve, taking another 2-4 days (have had the control valve replace 3xs). This means, my husband has to get down at eye level to try to get it to light (hes 63) & if it doesnt light on the 40th try or the cramp in his hand stops him sooner, we have to heat water on the stove, carry it through the house to the bathtub, try to get the temp not too hot or too cool, then hope that our 70 yr old bodies can get down into the tub plus get back out without falling (showers are preferable). My husband bought The best hot water heater $ could buy at our local Lowes store. Because we are getting up there in years, we hoped that this would be the best answer by also getting the extended warranty. They have had numerous repairmen out to our house (6 or 7 last count)... two different men told my husband that they would only be here a couple of minutes knowing it was not going to light for them either. Time wasted. Patience gone. Still they wont replace it because if anyone can get it to light up again, no matter how long that may take, then theres no need to replace it! They have already put more money into parts, labor & repairs than it originally cost. I was told today by the ex. warranty representative that its not considered a lemon! So how do those LOWES/WHIRLPOOL people sleep at night????

My Whirlpool Cabrio WTW5550xw0 has had many problems. It started with the lid lock error, replaced it, lasted about 2 weeks, and got another one. I did the diagnostic test that pointed me to the actuator, replaced it. It worked for 2 weeks, got another one, and then another one. I was getting a bad reading from the control panel, replaced it, and that worked for a while. I found out that the actuator had a little water drops on it. I figured that it must be the tub seal, so I replaced it. That lasted about a week and a half, and it started dripping again. Now, I figured it is that the transmission has bad bearings, that causes my tub seal to leak, that causes water drips to go onto my actuator, causing a failure in that, which can give me all kinds of bad readings on the diagnostic test. I have replaced at least half the cost of the original purchase price on a year and a half old washer. I also bought my son a Whirlpool Cabrio washer a few months before I bought mine, and he hasnt had a single problem.

I want to make this clear I’d give NO stars if I could!! Whirlpool is totally junk!! I bought a whole suite of Whirlpool kitchen appliances from Home Depot that is a dishwasher, stove, and fridge. The dishwasher never cleaned the dishes, always left a film on everything, cant clean out the drain area, the screens don’t come off and less a year later the dishwasher top rack literally fell off and broke all the glasses that were loaded in it and the fridge keeps freezing all my food!!! I keep having to adjust the thermostat up down up down just to make it doesn’t freeze. Now that the warranty is no good on any of the crap I will no doubt be charged an arm and a leg to get it fixed, which definitely won’t be worth it!!! Whirlpool is such crap!!! Made in America no wonder!!! Don’t buy any whirlpool anything!!! You will be very VERY disappointed!!! I’ve bought plenty of brand new appliances. Bosch is by far the best dishwasher even the cheaper ones. Now I have to pay to dispose the whirlpool crap!!! I am sure whirlpool doesn’t give a crap though!!! They will keep selling their crap, but don’t Buy it!!! You will be soooo disappointed!!!

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

We have a small space that fit a washing machine and figured we could add a dryer on top but didn't have an outside vent, so took a chance in this model. It fit perfectly in the space and saves us from a regular trip to the laundromat. It takes a bit longer to dry but is energy efficient.

I purchased a Whirlpool fridge (model GX2SHBXVQOO) on November 27, 2010 and it leaks water on my floor. I have to keep a towel there or it runs all over. I also purchased a Whirlpool range (model YGFE461LVQ) and the convection fan went on it a month after we bought it. The manufactures warranty does not allow repair people to travel any further than 100 km to repair, something that we had to take the stove in to be repaired. We got the stove back the same day and brought it home. Low and behold, after a short period of time it started to rattle again and got steadily worse. Also, now my one burner on high does not stay on high; it keeps going out then coming back on.I have called the place we purchased these pieces of junk from and they said there is nothing they can do. I also sent e-mails to Whirlpool and they said they will look into it and get back to me. That was months ago. I called Whirlpool and was basically told that there was nothing they can do, that I was to call the repairman. Never, never, ever buy a Whirlpool product.

Love my new fridge, not in love with the icemaker though. Every couple of days I have to reach in and scoop the ice off the little shelf in the back, or else it will quit making ice. The ice cubes block the arm from coming back down to trigger a refill.

Whirlpool Cabria Washing Machine hold down switched failed in just 18 months of use. It took the Technician 5 days to serviced and repair our Whirlpool top loading washing machine. The washer is till acting up and stop working unless you put a weight on the top loader cover.

Whirlpool Gold microwave quit heating after little use. We moved in house one year ago, microwave 6 years old. Spoke with Timena customer service rep. She took my model, serial info and clearly explained this model had defects and they would replace for free even though 1 year warranty was up. Delivery staff would call within 24 business hours. After 4 days I call back and get Mia rep, she claims I was disapproved for new unit after all?? I spoke to 2 supervisors above her Karin in Tennessee, and another. They claim I was mistaken??? I said, “Look up the recorded call and you will see the message is clear... They acted shifty and claimed I should buy a new starting at $1399!!! They would consider small discount?? Their rep was clear at first then they failed to back her up. Terrible customer service. Lied etc. Never buy Whirlpool!!! They are cheap and don’t stand behind reps. Awful company!!!

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

All I ever wanted was a nice refrigerator with the ability to get crushed ice from the door. We bought our refrigerator from Lowes several years ago and have had problems with the ice dispenser ever since. Lowes sent repairmen many times and even replaced the one we purchased with a newer model. Whirlpool refused to replace. The problem persisted and we had to continue calling repairmen. The last straw was when the repairman asked to borrow my hair dryer to help him melt the ice that continuously builds up in the door chute. I stopped going through Lowes and went directly to whirlpool for repairs. Since then I have been told that I should remove the ice box and clean out weekly, be nicer in order to get better help and that my husband should do the talking so that Whirlpool will be more helpful. I am so disappointed. Its been a couple of years since I last called for repairs even though we had the extended warranty. I have to clean the chute daily in order to get crushed ice from the door. Whirlpool knows that their engineers developed an ice dispenser with problems but will not admit it. Their customer service is the worst ever. I will never buy a whirlpool refrigerator again.

The washer worked well the first year and has gone downhill since. There is mold on the rubber seal where the door closes. This was supposed to be a recall and was never sent the replacement part. We have to constantly use bleach to clean the rubber.

Ive had so many problems with this washer. Everything has been replaced on the machine and it is still a failure! It has overflowed 5+ times. Stopped draining 4 times (fun getting water out of it...). Have been without a washer for a total of two months! My In-Laws have the same and theirs hasnt been a problem (however it isnt used as much as mine.). Hopefully mine is just a Lemon! Ill never buy another one!!!!! Especially from Lowes. They deem it only a lemon if it has had the same issue for 4-5 times. That is with the extended warranty! TO THE DUMP IT GOES!

My Whirlpool microwave broke. Im not sure how or why so today I purchased another 2 actually. Both were too big. The model I purchased is discontinued. I had to remove part of my Marble Backsplash - the turntable is tiny however mic is huge. Work on making microwave for smaller areas. Stick to get or Samsung for a nice size microwave not a Mongo mega oven above your oven.

I have a smaller/apartment size fridge. As a 1 person household it is a perfect fit. Works well & wasnt expensive. I am a Foodie, having it so nothing is too warm/cold, all the temps are equal, is a big deal. And in 10 years no breakdowns.

I purchased a washing centre at Canadian Appliance Source. I paid to have it delivered, installed and for them to take away my old appliances. I had several issues and when I called the store, they sent me to Whirlpool warranty who dispatched a repair technician a few days later. With nothing solved to my satisfaction, I called Whirlpool again. I spoke to a customer service rep who gave these responses, she put me through to a manager who gave me the same responses. When I asked to speak with someone above her, she said she could put me through to another person at her level but noone at a higher level.I want to hear the same response again? Really? Her only other answer was to email the Whirlpool Executive, which will be my next step. This is a summary only of my experience of the first few days after the purchase.Problem: The first load I washed was 1 set of blue sheets with 2 pillow cases. The water didnt seem to cover the load but I thought when it started to wash, they would get wet. When I took the sheets out of the washer, there were several dry spots and some kind of residue on several areas, so not washed or cleaned as expected. I tried washing one sheet, same thing. Tech solution: Put in some wet items to the load so the washer thinks the load is heavier and will add more water, or add a bucket of water to the load, Really? Whirlpool response: The washer is working as expected. Really? Problem: I did a warm water wash, expecting the machine to dispense a mix of hot and cold AT THE SAME TIME making it warm water. The washer starts with cold water then stops and puts in hot water. I dont want cold water or hot water on this load I want warm as recommended by the manufacturer! Tech solution:Dont use warm water wash. Really? Whirlpool response: Works as expected. Really?Problem: Dryer is way too hot on the delicate cycle, not good for delicates! Tech solution: Use the air dry cycle. Really? Whirlpool response: Dryer is working as expected. Really?Problems I didnt even discuss: The load is really really wrinkled when it comes out of the washer. Who wants to have to go back to ironing everything they own? The washer tub and dryer are really really small! I should have read more reviews and headed the warnings! Comments: I purchased online, biggest mistake. The store will not take it back. Whirlpool will not take it back. Hindsight is 2020! If I could have given negative stars, I would have.

Three Whirlpool fridges in 5 years. 1. Fridge one three doors replaced still not satisfactory, returned, warranty VOID. 2. Fridge two simply stopped being cold therefore not working 100+ food wasted before year. 3. Fridge three freezer leaking all over floor. Two years old 0 warranty left. I now pay again to repair. I am so beyond WHIRLPOOL PRODUCTS and so fuming??? Mad. $$$. 1300.00 to 1500.00 purchases ALL JUNK. NEVER WILL I PURCHASE ANOTHER WHIRLPOOL product. I do own a full file of continuous complaints. Brault & Martineau store Gatineau did the best to help with exchanges, sent repair man who did nothing. Will not deal with them again either.

I purchased a Whirlpool Cabrio washer and dryer from a local appliance center. Everything was working great. After some time, the washer began to have error codes. I would have to turn it off and restart using more detergent, more water and more electricity to attempt to get a load washed. I did purchase an extended warranty. I reported the issue to Whirlpool and I have had 7 home repair visits while still under Whirlpools warranty. The first time, the repair tech went under the washer and tightened a screw. REALLY! The next visit, the motherboard was changed and the issues kept coming back. Well, the Whirlpool warranty was now over so the extended warranty had to be picked up from the appliance center. Things got worse and had continued repair calls. After I had enough, I called Whirlpool and spoke to everyone under the sun. I tossed it outside and bought another brand washer. Several weeks went by and this washer still under the shed, Whirlpool contacted me and bought back my washer, GREAT.Now, here it starts all over again with the dryer, same issues with motherboard. Only this time, I am 1 month out of Whirlpool warranty and need $385 for a new motherboard plus cost to replace. I call Whirlpool again but only this time, they show no issues with this dryer and are not budging. I toss it out and again, purchase another brand dryer. I grew more angry by the day looking at this dryer sitting useless outside. I had it hauled off as trash. My question is how does a consumer protect themselves against these manufacturers? I do understand warranties but if it smells like a lemon, acts like a lemon, it must be a lemon!

I purchased my stove in June 2020. I had no idea it was to be connected to the internet, but no big deal. Had I known of all the other quirks I would have thought twice. 1: A red light comes on to tell you a burner is on but not which one. 2: A red light appears when a burner is hot but it doesnt show which one. 3: Only 3 burners out of 5 can be used for cooking the other 2 are warming and melting ONLY. 4: The stove updates its software whenever it feels like it and shuts off the oven and burners. 5: Periodically I have the oven on and it just turns itself off!6: The touch controls for the oven are in a bad spot because if you accidentally touch them when the oven is on the oven will shut off.Not sure if it has any serious problems just the inconveniences listed.

My experience was terrible. We purchased a side by side refrigerator on June 27, 2011 and it stopped working in December, 2011. We reported this onDecember 19, 2011. A repairman was sent out a few days later, who could not solve the problem because a piece had to be ordered. The piece was ordered and the repairman came to install the part on December 28, 2011.The refrigerator is still not working at all. We have been without ice for this period of time, not to mention the inconvenience of non-refrigeration of food. I pleaded for them to pick up the refrigerator and give me even a partial refund. I was told that three repairs had to be done before they would even consider picking up the refrigerator. I am not a person who complains, but this was ridiculous. I will never purchase another Whirlpool product.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

I have a lower end 4 burner model but I love it. Both power burns are in the front (I would change that) and electronic ignition. The oven temp is true and heats up quickly, I bake upwards of 700 cookies at Christmas time. Even being a lower end model it works great and I use it everyday. I think it is more energy efficient than the model that I replaced, which I replaced in order to have the electronic ignition. I would recommend this Whirlpool Range!

Sounds crazy, but the outside of my stainless steel door is all dented. I live alone and one day noticed that it looks like someone body slammed my fridge. Is there air in the door panels that could be escaping or something like that? Anyone hear of this?