As a rule, everything I put in it comes out spotless, but I know it is more a function of the detergent than the washer itself. Has nice features but the digital system does not allow you to turn a knob and go to a particular function like the older one, I miss that. Its a standard under the counter dishwasher, plain white with a nice, attractive operating panel with small LED indicators. NEVER put any vinyl, 45 or 78 record into a dishwasher!!! It will dissolve the labels, and if its made of acetate (home recordings) it will destroy it.

My new Whirlpool refrigerator has accumulated ice on the top of the freezer compartment from day 1. I called Whirlpool and a repair was scheduled five weeks later September 12. The repair person said he needed a part and would order a new light switch and ice door parts from Whirlpool. Ten days later he came back with a new switch and instructions to file some plastic off the ice door part so it will close properly. It only partially worked; ice stopped forming in the ice chute but still formed on the top around the light switch. The new switch is not flush with the liner and the plastic liner has a small crack starting at the switch. How Whirlpool wants to cut out a six inch square of the liner including the switch and glue in a patch. This patch would only be warrantied for the balance of my one year warranty. I find this unacceptable and will complain to the store where I purchased the refrigerator.

I bought my new Whirlpool Duet washer and dryer in November 2011. Washer was loud from day one, but I never owned a front loader and thought that is how it was. Then someone told me that meant the bearings were bad, so I called. While still under warranty, they did replace; and I had to wait 6 weeks. Then a few months later, it started leaking. I had the extended warranty, and A & E came out and told me the bearings failed again. And now, I get a check for $750. But the machine cost more than that. Do not buy any Whirlpool, Maytag, or Kenmore. They are all made by Whirlpool.

My family purchased a Whirlpool Cabrio washing machine approximately 4 years ago. The first two years were fine. I had no issues out of the machine at all. The last two years (just as my warranty expired) have been terrible. It was serviced twice just before the warranty was up and my husband has serviced it twice since. On two separate occasions, the bearings have worn-out and the bottom seal leaks water all over my floors. I would never recommend one of these machines to anyone!

I had this dishwasher for about a year. It was a great purchase for this model and the price was reasonable. The dishwasher is very quiet and wash dishes wonderfully. The only exception is it does take a long time to wash dishes. The cycle are long.

We purchased a 50 gallon water heater that claimed to come with a 6-year warranty on parts. Its been a little over two years that we owned the product, and we noticed rust on the bottom. We checked to make sure if water or even moisture is visible from the outside - nothing. The problem is obviously coming from the inside. Since we have warranty, we called them and got nowhere! We were told that it is just cosmetic. They refused to send out a technician to take a look at it. We even emailed them pictures (see pictures) and still nothing, no service. Their warranty is a joke. We will never by any Whirlpool product ever again. Dont believe the sticker that claims you are covered for a certain amount of time. When it comes down to it, they will not do anything for you.

I purchased a brand new 2019 Whirlpool side by side refrigerator in October of 2019 for my new house. Yes, that was 2.5 years ago. HOWEVER, I live alone and hardly ever use the ice dispenser. Maybe, it was used 20 times in 2 years. The ice dispenser just stopped working and today I notice the refrigerator is not even making ice! What a piece of garbage!

I am very happy with this dishwasher. It is not a high end, rather middle of the road, but is very quiet, does a great job of cleaning my dishes and pots and pans.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

We purchased this washer and dryer new in 2011. Have repaired door to washer twice. New doors total cost $500.00 each time. Now it is cracked yet again and the dryer door has to be adjusted. The temp does not work right. Have to do minimum of 2 cycles for drying. Very unhappy. We may as well buy a new set of another make. Tired of the expensive repairs.

I am following up on a review I submitted on April 22, 2015 about a Whirlpool refrigerator with french doors and bottom refrigerator. At the time, paint was falling off from the door as pictured in the previous review. This another chapter on this story and probably the closing chapter. A few months after the paint event which I could have lived for a while, the right door hinge literally disintegrated leaving the door without support. The door seals material is of such poor quality that they have disintegrated and the water condenses inside. The bottom photo shows hinge components that came off the door hinge on the kitchen floor. The second photo from the bottom up photo shows how the door scraped the plastic of the freezer door top trim if the door is not lifted to clear it. The second photo from top to bottom shows the door over the hinge pin if I am not careful lifting the door to clear the freezer door.The first photo from top to bottom shows how the door remains open if not lifted so that the door magnetic seal keeps it in place. It is very hard for me to believe that a country like the United States of America treats its customers with no respect. I met my obligation to pay the amount on the price tag of this appliance but I cannot say that Whirlpool did its part of providing a basic quality product. There is no consumer protection agency in this country to protect consumers from corporate predators that have no sense of a fair deal with a customer. So here we are, being abused by United Corporations of America. I hope the future brings a different understanding of the american people on these matters. Thank you for the opportunity to express myself on this matter. Next step... buy a foreign made appliance that will support another country work force... sounds familiar.

Do not waste your valuable dollars on this refrigerator. Not even 5 years old and have had nothing but issues with this fridge. The ice maker quit a few months ago, started leaking water from somewhere behind the wall panels and now the freezer door is frozen shut and the refrigerator section is warmer than the outside air. Did I mention that this refrigerator isnt even 5 years old yet? A piece of junk is a piece of junk and this fridge is a piece of junk!!!

I purchased the Whirlpool Cabrio, Model no. WTW5640XW2, on March 3, 2012. I have tried every setting and water temperature and am totally dissatisfied with the washer. It does not clean clothes, tangles them into a twisted mess which requires that they be vigorously shaken out, destroys anything with a draw string. I had an online chat with a representative and was told she was sorry. I posted to Facebook and did receive a call from a repairman, which I will return; however, I do not anticipate receiving any satisfaction. The machine is worthless for washing clothes. I was better off with my 12-year old agitator Whirlpool washer. I do not understand how this machine can be allowed to stay on the market. Id be better off at the river beating my clothes against rocks. I hope someone will get on Whirlpool to give consumer refunds. I have been brought to tears by this machine and I am one tough cookie. Please help!

We our adding our name to a list that is remarkably long. We purchased a top loading Cabrio washing machine just over a year ago and the problems with the balancing of the unit are the same as everyone else who has written in. The service company A&E has promised a lot but has done little to resolve the issues we have had with the machine. One representative told us that she would order the part and have it sent to our home. When the part did not arrive, we called A&E back only to find out it was never ordered because the service technician would not return their phone calls. I find this excuse ridiculous and similar to other false statements they have given us on the other four phone calls made to address the problem. After reading these reviews, we realize that this is only the beginning of what will be a frustrating and costly experience. Never again will we buy a Whirlpool!

I spoke to Sue in Tennessee that refused to let me speak to a supervisor regarding replacing a light bulb in my microwave. Sue insists that I can do this, despite no instructions in the owner’s manual and warnings all over about electrocution if I open the panel. Sue refused to assist me and is sending out a repairman. I will never do business with this company again, and I am angry that Sue refuses to see a problem with me paying $75 to replace a light bulb in a nearly new microwave. She continued to give me incorrect instructions on how to replace the bulb, and the owner’s manual does not have instructions nor do they exist on the internet. The owners are not supposed to dismantle this model, but Sue at Whirlpool Customer (no) service told me that I have to pay. Seriously? For a less than two year old microwave? Never again. I think I will take this unit out and get a GE.

I purchased my Whirlpool refrigerator last Summer and so far I’ve had no issues, no probs! I love the energy efficient refrigerator along with its easy settings and options to use a ice maker. Wouldn’t trade my Whirlpool for any other brand!

I bought a brand new washer from Home Depot, Whirlpool 4.3 cu High Efficiency Top Load Washer to be exact. It hasnt even been 90 days and it started to make the loud, horrible noise so we had someone come and look at it. Apparently the transmission blew and the oil leaked all over my tile floor. I work full time and I do laundry only on the weekends and there is only two people living in the house so you can imagine we do not use it that much. I went to Home Depot first and since it was past 30 days we had to called Whirlpool direct. The customer service is horrible. I thought since the transmission blew, they would replace the entire machine since that is the brain of it. NOPE! They said to replace the entire machine and give us a new one, it would have to break 3 times. Are you kidding me? They did not offer to reimburse the tile damage or the amount of money I had to spend at the laundromat. Not to mention its been over a week and the guy still has not come out and fixed the transmission. It would not be a big deal to me if the hose broke or something simple, but imagine if you bought a BRAND NEW car and the transmission broke 60 days after you bought it. You would take it back to get a new car. The customer service line could not care less about the issue. I spent over 2 grand in appliances from Whirlpool and I will never buy their product again because of the customer service and the fact they did not want to make the situation right. I just bought the machine brand new for a reason!

After only 14 months of light use, the magnetron in my over-the-range Whirlpool stainless steel microwave failed. The cost to repair was $350. I paid $450 for the whole unit upon purchase. I wrote to Whirlpool with documentation and got a voicemail that they were sorry, but the 12-month warranty had expired. The independent repair person said it is the Korean manufacturer of the magnetron that is the problem. He is replacing units all over town on all kinds of models Whirlpool is involved with, including KitchenAid. Whirlpool needs to get their money back from Korea! I will never buy another Whirlpool product and have told them so.

Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty. Spoke with manager, Tracy **. She said they would not help - out of warranty. Called local parts/service center - ea. hinge is $42 plus shipping and labor to install. Obviously this is a defective design. The lid is too heavy. I was having a difficult time deciding to spend 150-200 dollars every 2-3 years for hinges on a $700 washer and then I read all the other complaints about Whirlpool washers. I will sell it for scrap and buy a better brand.

Immediately after purchasing an entire kitchen of Gold Series kitchen appliances including the refrigerator with bottom freezer in 2/2013 from Lowes we began having issues with the refrigerator. I am not an engineer and dont profess to be, but even I can figure out that the whole thing is a problem based on a design issue. The top drips water consistently and has from the first, which has been addressed numerous times. Ice maker replaced trying to fix the situation two times. The freezer guides were messed up and off from the beginning, and had to be ordered-waited for, then installed. In total a repair person has been here, an inconvenience on our part - 7 or 8 times and we still dont have a refrigerator that works properly!The last time we had someone look at it, there was a part that had to be ordered from, yes, Mexico and we had to wait a week or so and they told us they could rent us a loaner!!! Are you kidding me?? I should have kept the old 26 yr old fridge in my garage that is still working that was built in America! After buying $8000 in appliances and supposedly a top of the line brand name that in the past has shown integrity to their products... I pay my bill each month, because if I didnt someone would put it on my credit. But who puts it on Whirlpools credit? Who is going to hold them accountable and how many complaints must there be in order for someone in the government to step up and do something to a company that is taking tax dollars from our US and sending it to other countries but selling less quality products to those who do pay the taxes? I am ready to sign a petition! I should have gone with the other brand! Any other brand would have given me a better shot than this of having less of an issue! Terrible experience and certainly NOT GOLD! Shame on YOU Whirlpool!

Its now Nov 8 and Ive been officially dealing with this issue since Sept 26. This washer was installed in a new home. After less than 10 loads, my washer stopped draining and I was left with a load of towel soup for over a week while waiting for a service call. I still have the same defective non functioning washer sitting in my home and have been unable to do laundry at home in all that time. So far Ive spoken with 2 customer service representatives. The first was incapable of scheduling a service call. She clearly did not understand how to operate the database used for scheduling. I was finally able to schedule appointment on my own but had to wait a week before the technician was able to come by. It was determined that either the latch mechanism or the mother board or both are defective from the factory.The second was just plain dismissive and completely unhelpful. I sat on hold for about an hour each time before getting to speak to a person. Ive also received two canned emails in response to my poor review of this washer on the Whirlpool website. They basically blame COVID for the delays and state the parts delivery should take 3-4 weeks. I was originally told 14 working days for delivery of the parts. We are already past both deadline with no end in sight. At this point, Id like the defective washer replaced rather than repaired. And for the record, this was a new washer (less that one month old) installed in a new house that now stinks to high heaven because slimy, scummy water that will not drain out has been there since September 26. Id really just like for someone at Whirlpool to honestly care about this and take a moment to address this issue.

I paid $1246 for a Whirlpool glass top range. This was not a cheap model, but I wanted it as the starting point of my new kitchen. After only about a year, we noticed that the area surrounding the operation controls was turning a funny color. On closer inspection, we noticed what appeared to be something peeling off, it was paint! The area surrounding the controls, which appeared to be brushed metal, was actually painted plastic! I was furious that an appliance at this cost level was made of plastic....really, a stove top made of painted plastic? I complained and after a huge fuss they agreed to come out and replace it ONCE. Well its been just over a year since they replaced it, and guess what? It is peeling off again!I dont know what to do, as Whirlpool obviously has gone the cheap end and doesnt want to fix problems. As others have mentioned, they say that it is JUST cosmetic, and they wont cover it under warranty...now my first new appliance for my first new kitchen since 1972 looks like crap! I should have kept my old avocado green appliances - they lasted over 40 years, still worked, and still looked good (except they were green). I wont ever buy another Whirlpool appliance. For those who mentioned that their appliance would turn on unexpectedly, please check recalls....this is one of the major problems on recall. Buyer beware!!!!

Initially felt the burners and oven took a LONG time to heat up, but just accepted it. After a year and a half, the motherboard died. The part alone was almost $400 and labor $100. The self clean does not work very well. Glass top is very hard to clean. It has a large oven space and looks nice, but would avoid Whirlpool at all costs following this experience.

The shelves in freezer don’t lock into anything so if you don’t balance the food right on the shelf it will tip over. I had to replace the fan motor in freezer. The refrigerator is only 4 years old. The little tray under the water and ice outside of door if you shut the freezer door too quick water from tray goes everywhere. The water filter cost $50.00. If you have bad water you will need to change it twice a month.

We purchased a brand new stainless steel refrigerator in 2013. Our 2 year refrigerator stopped producing ice and the freezer stopped working as well. We called Whirlpool customer service and they said they could not help due to 1 year manufacturer warranty only. We called another company (SoBellas) that charged us $85 to tell us that it is the seal system which should be covered up to 5 years by Whirlpool. The man showed me the Whirlpool refrigerator warranty on Google which states the sealed refrigeration parts are covered up to 5 years. There was no specific model numbers listed which gave me the impression this was a standard warranty for all Whirlpool refrigerators. I explained the situation to Whirlpool customer service including the 5 year warranty that is found on Google for everyone to see. I was told that our refrigerator model number did not qualify for that specific warranty. We ended up having to buy extended warranty for $350 on top of the $85 we already spent. This started July 24, we had to wait until August 10 for Whirlpools warranty company to see us. They checked it and said they had to order parts but he supposedly tweaked it to make our fridge run better.... It made it worse and it ended up completely breaking down. We had to buy ice chest and waited until Thursday August 27th for them to finally come back with parts and fix the refrigerator. I took time off from work once again due to our time slot being between 3 and 5 but the guy didnt even show up until 7:30. I could have worked my normal hours instead of taking more time off! The guy never once called to inform us that he was running late. We kept calling the company to make sure we werent forgotten. The guy told us that everything should be working within 20 hours or so, by Friday our freezer was still not working and no ice either, back to square one! I called Whirlpool customer service once again to explain the situation, nothing could be done. The next available time for them to come back out is September 17 for them to come look at our refrigerator. We have been stuck without ice and a freezer, buying food every other day waiting for our brand new, horrible Whirlpool refrigerator to be fixed. Will never ever buy Whirlpool brand again! Actually, we purchased all brand new Whirlpool appliances... Good luck to us!!!!!

Im with the rest of the people on here... The only mistake I made was not checking the reviews before purchasing a Whirlpool product. My washing machine is horrible... I dont recommend anyone purchase any Whirlpool products. Its cheap and has already stopped working twice in the last 6 months... I have had a repair man come out twice to replace the door locking mechanism... Not to mention the buttons dont work, they just slide back into the machine... Plus, you have to jump through hoops just to get the machine started the way you like it... If you make a mistake, there goes your whole ** load of laundry, not to mention the water wasted. Hell with Whirlpool - Dont ever buy a whirlpool product as long as you live.

I bought my Whirlpool top loading washing machine 07-22-14. I so dislike the locking mechanism and will be certain to never, ever buy a machine with that feature again. It is so irritating to try to add something but cant because its locked so have to hold the button 3 seconds to unlock and start all over. If there was any way to get around it I would. I will stay away from Whirlpool products in the future and will be sure to check the next time I buy that the lid of the washer can be lifted when not spinning. Also, I do not like that it sticks on rinse sometimes and the only way to end a cycle is to hold the button and then start over with much wasted water.

Whirlpool washing machine model WCW4950XW2 - We have a barely two year washing machine that we purchased at Best Buy and it no longer drains or spins. After $100 repair call we were told that this is a common problem with this model. It is a transmission problem, and with the way the machine is built a repair person cannot get into the transmission to fix it. He suggested we buy a new washing machine. This is a travesty on so many levels! If whirlpool know it has a problem it should offer a partial refund for the purchase of a newer better machine. I keep thinking about what our landfill in this world look like with the proliferation of appliances that are engineered to last a year or two. I can guarantee you I will never purchase any Whirlpool produce again, and I will research whether other brands are associated with the whirlpool brand before I buy it. Sad that a once good company has gone to hell.

I purchased the Whirlpool Cabrio set about 5 years ago. My problem is that the washing machine has NEVER gotten our clothes clean. The dryer is fine but the washing machine is useless. Clothes come out of the machine in the same state that they went in even if I use stain remover. Dont buy this machine!!

I purchased a new Whirlpool (2015) Model: WRF736SDAM13 French Door Refrigerator. Two days later, water was dripping from the light in the top of the refrigerator. I was removing about a cup of water twice a day, which dripped from the light. The company was friendly when I called, and offered a replacement or repair. I elected the repair as I felt that would be acceptable. The repair man inspected the refrigerator and determined the problem to be condensation from the water holding tank, located in the top of the refrigerator. He stated that because the incoming water has the opportunity to reach room temperature prior to entering the fridge, and because of the high temperatures (80’s & 90’s) the water holding tank has condensation that collects in the top of the refrigerator, which drips onto the top of inter refrigerator liner, and eventually drips through the light. He stated there is no fix, as it is not broken. While it is not broken, this is a bad design error, which would affect anyone who lives in an area where the temperatures exceed 80 degrees outside, which could only be fixed with a collection tray that would allow the water not to drip into the refrigerator. Currently there is none available. Because I only had the refrigerator for two days before the problem was reported, Lowes allowed me to make an immediate exchange. However, had this been purchased during cooler temperatures, the issue would not have been noticed until after the 30-day time frame and the exchange would not have been an option. When I made the exchange, I noticed that all the 3 & 4 door refrigerators are made the same and will have the same problem. I ended up exchanging it for a Samsung model. Kudos to Lowes. Whirlpool, you need to find a fix for this problem if you want to sell me another one.

Purchased electric double oven range WGE555SOBS02, from Lowes end of 2014. Couple months it came on by itself, middle of night, 879°. Repaired panel 3x, then Lowes replaced stove, middle 2015. 6/26/2017 error message F2E1, control panel... stuck / shorted key. Out of warranty. Lowes and Whirlpool both claim no previous complaints. They will send repairman to assess problem, $150.

I love my Refrigerator. It is a side-by-side with ice-maker and water in the door. I have plenty of room in the refrigerator, and I really like the adjustable shelves. I would definitely purchase another Whirlpool (next time with freezer on the bottom). I love the Stainless and would probably purchase again - or depending on the kitchen maybe black.

We have had our washer just over a year when the plastic hose that fills the detergent tray began leaking. The entire assembly is plastic and poor quality. Whirlpool customer service says since it is after 1 year, that I would need to pay for the parts & service ($489). I would not recommend this machine or anything Whirlpool.

Just got new side by side to replace old one. Motor runs every 30 minutes. Stays cold and makes ice but Im concerned about noise. Called Whirlpool and was told to record noise and show to Home Depot where it was purchased. No help from either place. Need to call warranty company. Funny thing it arrived with pieces of some sort of shrub in drawers. I guess this is new and improved and energy saving like newer washer that takes 45 minutes to wash a load.

I purchased a dishwasher from Menards. It was a top of the line Whirlpool Dishwasher. We ordered new cabinets for a kitchen upgrade and when the cabinets arrived they were damaged during Thanksgiving holiday. We purchased the dishwasher and it sat in our garage until the second set of cabinets arrived in mid January.Once the GC installed the new cabinets we noticed a small dent in the front of the stainless steel dishwasher. I notified Whirlpool and they took my model and serial number. The supervisor April said there is nothing that I can do. You passed the 30 day cosmetic warranty. I explained the issue to her and she didnt seem to care.The dishwasher sat in the garage for 7-8 weeks. This is not the consumers fault. This company could of sent a service mechanic out and replaced the front panel. But she chose to ready some meaningless policy to me. I will never buy a Whirlpool product again, and I will tell everyone about the poor and unprofessional service that Whirlpool offers.

When purchasing a new home, the almost new Whirlpool double-door ice-dispensing stainless steel refrigerator came with the kitchen. This beautiful-looking fridge worked well for close to three years, but gave up the ghost shortly after its warranty expired; designed obsolescence perhaps? Problem was, it would have cost almost as much to repair as it would have to purchase a new fridge with a warranty. So, thats what I did, via a local big-box store. I bought a single door floor model, with the Whirlpool ending up as scrap, the whole incident leaving a bad taste in my mouth. If you have your grandmothers old fridge that still runs, keep it!

I purchased a Whirlpool microwave at the end of November 2015. Since then it has needed repair 3 times. Now I am being told it is not repairable. Microwave is only 1.5 years old and Whirlpool would not stand behind its product and provide additional warranty service or even a discount toward a new one. When I asked to speak with a supervisor I was just left on hold, 20 minutes later I hung up! Poor customer service!

We bought the microwave in August 2018 and last week it burned a hole through the turn table which broke it and burned a hole in the floor of the microwave. Whirlpool said it was under warranty but refused to bring a new one. They ordered a new glass turntable and painted the spot that had the hole burned in it. What makes me believe it is safe now to use? What caused a microwave to go awry in the first place. It has to be a safety issue and Whirlpool will do nothing about it. Lousy customer experience.

I purchased Whirlpool Slide-In 30 Gas SS Conventional Range. Terrible product quality. After about three years of use, the range shows an error message cooling fan is too low. I wasnt able to use the oven. Abt Services came in to do the repair. One month after the cooling fan was installed, the same message came up again. When Abt Services replaced the cooling fan again, the display was completely out. The cost of the repair parts is over $800. Are you kidding me! I paid $1500 for the range. Now I need to pay $800 to repair. Whirlpool didnt offer any discount for repairing the defective product but offered purchase similar product at a discount price. I will never ever pay a dime for Whirlpool product. It is a nightmare using the product. I learned my lesson. No Whirlpool product again in our house.

After 2.5 years seal around door melted on microwave. Whirlpool Corp sent a repairman to do a safety check. Said unit was ok to use. Plastic seal on for area totally melted about 2 inches wide. Co. Had a recall about a similar problem but our serial number was not included???? Did not want to give them any stars.

I purchased a Whirlpool Microwave on 9/21/10 from Hamilton-Bryan in Wichita Falls, Texas. I had a small fire in my microwave on 9/19/11, due to a faulty mica board. This was replaced by Mr. Bobs in Wichita Falls, TX, under the warranty. Then on 1/9/12, the microwave would not warm anything. I called Mr. Bobs again, and they said the transformer was out. I called Whirlpool, and was told by Yvonne that Whirlpool would replace the part only, with no labor, but Mr. Bobs was closed, and to call back in the morning, so this authorization could be set up with Mr. Bobs. I called back and there was no record of my call with Yvonne. I talked to a supervisor Rachel in Tennessee. She put me on hold for a while and finally said she found Yvonnes note to authorize the part. I explained to each person I talked to that I was dissatisfied with Whirlpool. I believe I have a defective microwave. I would like my money back, or a new microwave. I believe the defective mica board is related to the defective transformer. I am a very dissatisfied customer. I have used Whirlpool most of my adult life. I have used them since the 1970s. I currently have a Whirlpool refrigerator, washer, and dryer. A similar situation like this occurred when I bought a Samsung washer. I was dissatisfied, and Samsung refunded my money, and I bought a Whirlpool washer to replace Samsung. I will not be satisfied with this situation, until the microwave is replaced. Thank you for your concern and attention to this matter.

Purchased a Whirlpool Cabrio washer WTW5800BW0 September 2014. Two years and 8 months later it no longer works. Call Sears and Whirlpool and was basically told I should have purchased a warranty. Whirlpool tried to sell me an extended warranty for $495.00 which is about 80% of the original sale price of the washer. Was told it is my responsibility to care for the maintenance of my purchase. WOW. Way to stand by your product. So now its my fault they sell a product that does not last longer than 3 years. So we tried option 2 - called a repairman. His response save your money and buy a new washer. WOW. A repairman rather lose money than try and fix this washer. Save your money and pass on Whirlpool products.

I bake a lot so my husband bought me a new gas range for our 54th anniversary. After the first few times I used the oven, I decided to clean it. I noticed then that there were some burnt grease spots and streaks between the oven glass door. After 2 years of use, it has gotten much worse so I decided to take the door apart to try to clean the glass in between the layers of glass but there are three instead of two. I cleaned the inside of the outer glass, but that didnt take care of the problem. Most of the stains are between the other two panes of glass. That, I cant get to. I feel that this is poor design and not sealed properly. I take good care of everything I own and I expected this range to last me the rest of my life but it is put together with cheap plastic parts that wont last long. It is the first new range that I ever owned and paid a lot more for it than any Ive had. I expected better.

I purchased this machine, a Whirlpool Cabrio WTW5640XW, from Lowes on Dec. 11, 2010. I just realized today, Dec. 24 2012, I had a 2-year extended warranty plan! Shame on me. At any rate the washing machine is very hard on clothing, tearing light fabrics and ruining my wifes bras. The clothes often come out with shreds of fabric from the other clothes in the washer. Oftentimes, it will not complete a cycle because it constantly goes out of balance. Today I paused the machine halfway through the wash cycle after the soak cycle to throw in some more laundry and start the cycle over. Half the clothes were still dry! Yes it may save water, but if you only use a cup of water for a load of clothes, how well can it clean? My wife has sensitive skin. So now we wash a load with extra rinse and normal soap then run the cycle again with no soap to get the soap residue rinsed out. Were saving big now! Yes, we are using HE detergent and the recommended amount. The machine is pure junk. I would love to see a class action suit against Whirlpool for selling such an inferior product. I know thats asking a lot in the land of no accountability we live in today, but one can always dream.

Bought the HE Whirlpool Cabrio in 2013 after having my old agitator Maytag for 19 years. After reading the other reviews I do not feel alone. An awful washer, a year after our purchase the spin cycle is so loud we have to close the laundry room door. Now it has been leaking into my basement. I called a repairman, explained my problem. He suggested to junk the washer, it will cost more to repair than buying a new washer. In addition my clothes did not clean properly, soap stains on clothes because it does not use enough water. This was about $1000 purchase that lasted less than 4 years! I am done with Whirlpool and suggest to anyone not purchase a HE washer, nothing like the old style agitator washers.

My appliance is less than two years old, and it wont stop heating. I have to manually turn it up and down to heat water, which seems strange, since most or all of the complaints are because it wont stay lit. Mine stays lit (knock on wood). It wont shut off. A new thermostat costs $60.00 after two years? Please.

Cabrio washer broken lid, asked WP to fix warranty. They offered $250 off $500 Amana washer. Said just send me the new lid that would cost me $210. They said no. Asked if they would send me metal lid with hinges less than $100 they said no. Told them I was not going to spend more money with WP, my turn to say no. If you are wise dont buy WP products...

I purchased this Whirlpool Cabrio Platinum washer on 12/1/12. I started getting an F1 fault and all the lights on the machine light up like a Christmas tree during cycles now. I thought I would research Google to see if others were having the same problem. I was VERY disappointed to see all of the same issues others were having with this high end washer. Without even calling a repairman, I know that this motherboard fix is $400+ based on all of the negative feedback. We have a large Whirlpool plant in my hometown, and I hate to see the lack of resolve by Whirlpool.

My machine has been ripping clothes for a few years but I thought, initially, that it was a snap, zipper or hook causing the problem. I recently got fed up and found this: **. It makes it pretty clear that it is a manufacturing defect. I called their customer service centre and spoke to a supervisor that told me it is normal wear and tear and that perhaps the glass in the door had worn out. Yes, thats right, she said maybe the glass has worn out.They are offering ZERO assistance in what would be a $500+ repair for me. Admittedly, my machine is five years old and out of warranty, but to me, when the repair is to install an entirely new style of door so that the clothes no longer get caught underneath, it is a defect. 43 different models of their machines are included in this issue and it was identified in 2012, a year before my machine was made. Why didnt they correct it before that?

I purchased this stove in September and I am very unhappy with the Aqualift. The service department said I would have to probably do the cleaning process about 7-8 times for it to really work. I find that very unacceptable would never recommend this to anyone.

One year old Whirlpool gas oven/range w messed up control panel. Every brand new Whirlpool so far has broken or is messed up within first year of purchase. I am going to complain to BBB.

I bought a Whirlpool High Efficiency top load washer. It does not get the clothes clean. Dark clothes come out with spots all over them. There is not enough water to rinse out the dirt. It is left on the clothes in spots. I have to take my clothes to the laundry mat to wash them to get them clean. I am 74 years old and have used Whirlpool appliances all my life. I have dt3 rental houses I keep Whirlpool appliances in. But I wont be buying any more. I had to call the repair man one month after I bought it. He had to recalibrate the machine. If all you want to wash or maybe rinse out is a pair of slacks or a shirt, it might be o.k. but not a load of dirty clothes. It is just a JOKE.

We bought a side by side refrigerator/freezer in 2013 from our local Best Buy. We have usually bought Whirlpool appliances. Before we bought this refrigerator the last Whirlpool we had for 25 years. This past week our refrigerator went out. We called a repair man. He said the circuit board was out and would cost $450.00 to replace it. We decided to buy a new one. I am very disappointed that it only lasted 7 years. Oh I forgot to mention the ice maker went out about a year ago. We did get new filters as instructed. We did not buy another Whirlpool.

Whirlpool Refrigerator WRF736sdam13. Purchased from Lowe’s June 2015... freezing started in April 2019. Freezer bottom is not draining correctly and the bottom keeps freezing making it difficult to push door close. I have the extended warranty. This will be the 5th time on Monday, July 29 repair person will come out.I talked to Whirlpool and Lowe’s. The product cannot be considered a lemon because the problem continues to be “fixable” as stated from answering service when I reported the problem again. Customer service has been amazing up to this point. Anyone else have an issue with this model with the bottom freezing solid? Any suggestions?

I had a Whirlpool GI7FVCXWY01. Purchase 3/13/2010. I had repairman after repairman come to fix it. The last one probably saved my family and my house. The light in the back corner was not only blinking, but flashing rapidly, much like some wild party light. It eventually stopped. The freezer works perfectly fine, the fridge works when it wants to. The ice maker makes ice some days but not others. The motor on the ice dispenser is completely frozen up. Does that all sound about right? If it does, clean it out and cut the power to it before someone gets electrocuted or your house catches fire.If you cant find the electrical diagram, or the company wants $455 to answer your questions, look under the right side of the freezer draw, but not on the draw. Remove the guard on the very bottom of the unit, near the wheels on the right side. You will feel a plastic bag attached to the underside. Inside that bag is the complete diagram of all the wiring harnesses along with the schematic for the amps and voltages for each wire. Are they telling your circuit board is bad and you will need a new one? Before you do that, inside the fridge compartment, in between the water filter and the ice maker, remove the light cover. Notice that inside that space is the access to another panel. Remove that panel. BE SURE THERE IS NO POWER RUNNING TO THE UNIT FIRST. Here you will find a connection plug with more or less 15 wires that are connected to the main wiring harness. Above that plug you will find a holding chamber. This holding chamber contains water from the filter that is waiting to go to the ice maker. It has dripped condensation on the plug since the day you first turned on your fridge. Your wires are most likely broken and corroded. You will need to have your unit completely rewired, but because of the design flaw that fix will only buy you another 4-5 years. My Whirlpool GI7FVCXWY01 left yesterday 5/15/2014 and none too soon.

I ordered this Whirlpool 29 cu.ft. white french door refrigerator online from Goedeckers on April 26, 2013. Delivered May 15, 2013. Ever since we got it, there was a frost buildup in left back of ref. Also ice would fall out of dispenser all by itself. Also a buildup of ice under ice bin. Water would also drip from dispenser. We thought maybe since it was new these problems would go away. But they just got worse. I called Whirlpool & they sent out tech on 8/12/13. He told me Whirlpool has a problem with these refrigerators & would order parts. Well after 3 times of cancelling repairman due to parts on backorder, I told repair I would call when parts come in. I keep calling Whirlpool & keep hearing parts are on backorder, saying parts will be in in 7 days. I call back in 7 days and hear the same lies. Its a shame that they cant get parts in knowing that there is a major problem. It sounds like a real quality control problem. I really pride myself on buying American made but Whirlpool is not helping my case for buying American made. It would be nice if they offered to replace it being they cant seem to find parts.

I bought a Whirlpool duet washer and dryer. These appliances are still under one-year warrantee. My washing machine was broken for four weeks, and they have been unable to receive all of the parts needed to repair it. They have made three appointments to fix the machine, telling me that they have the parts and only to cancel the appointment the night before. I have tried to get Pacific Sales to exchange the broken machine, but they will not do that or compensate in any way. This is a top of the line model; I would have been better off with a low-priced model, and I might actually have a machine that worked. Whirlpool supposedly had the parts on back order, which is not what Whirlpool informed me when I was able to reach them.

I have had my Cabrio for a year now and quite frankly, I find more satisfaction taking all of my laundry to a local laundromat. There is no soak cycle and when you have a kid in sports, that doesnt help. There is no agitator, and I am now convinced that they were originally in all washers for a reason. My clothes have all worn out and are shredding, not to mention my very expensive bath towels that I am now cutting into rags. This was the worst purchase I have ever made in my life and will never even look at a Whirlpool again. When I bought my house, I had a Maytag that was 35 years old and it did a better job than the new Cabrio. Should have stuck with that brand!

I purchased this washer (Whirlpool Cabrio Model #WTW8000DW) 10-25-17 from Best Buy & now it has no power to the panel at all. The power to the outlet is fine which I can plug a hair dryer in & the hair dryer works. Tried all the reset buttons & options with nothing on the panel working as well as unplugging. Still nothing. It is barely 4 months old & I am very dissatisfied for the amount of money I paid for a high efficiency top loading washer.

I bought this washer (model WTW7800XW) on 12/23/2010. Never happy with its performance from the beginning. Within the first 18 months, the lid hinge completely rusted and broke. The repairman stated that the hinges and glass lid would need to be replaced at a cost of over $400. We paid $899 for the washer. Instead of paying that much, not knowing if it would only last another 18 months, we removed both hinges and removed the lid manually to use the washer. After complaining to Whirlpool about the problem, they thanked me for the info so they could use it for the future. The latest problem to arise is the light inside the washer. The mount for the light was made of steel and has completely rusted away, so the light is just hanging inside the washer. Whirlpool needs to step up and resolve the issue with an extended warranty for these machines.

I bought an adapter that I added to the kitchen pipe, drilled a few holes in my cabinets to route the hose and voila! It is small but big enough so it's perfect for me. I didn't realize it had an internal heater so I was moving the hose between hot & cold under the sink but now that I know. I will try the heater. The settings are complicated so you have to read the instructions fully. Before I read them I thought every load took 2-3 hours but they don't. I do like to use the heavy soil setting and that does take a couple hours, but if I'm in a hurry or the load is not that bad I use a shorter 50 min setting. For the drain hose I either put it out the window or put a screen in the sink & tie it to the faucet. You have to tie it down wherever you aim it because the water comes out with enough force to throw the hose. I had a couple incidents of kitchen flood before this stuck in my head, now that sucker is secured well. I intend to make a permanent drain to the pipe eventually but for now I just use window/ sink. This required a longer drain hose. For apartment use, I am very happy.

We purchased 4.0 cu. ft. Cabrio Top Load Washer with 6th Sense Technology MODEL WTW7340XW2 on 11/20/2011. We are a small family of 3 so use of the machine is light. We noticed a strange sound and some leaks a week ago and called in a technician recommended on the Whirlpool website. To our horror he informed us that we need to replace the tub bearing assembly, rotor and stator - to a cost of $1095! This machine is not even 3 years old. Did we buy a lemon? I called Whirlpool. They were simply not interested. The online chat person sent me to the Whirlpool Customer Experience Team where I was told that I should buy an insurance plan to cover the costs of repairs. They then sent me on to the insurance department who want me to pay $338 to buy a repair plan to have the machine fixed. And then referred me to the Manufacturing division when I wanted to know how to escalate the problem - and if you call that number - there is no option to deal with problems - seriously?!? Is this what I should expect when buying the Whirlpool brand?

This is not a new washer (Whirlpool Cabrio INTW6200VWO) and it works well BUT since we have owned it we have had rust at the bleach dispenser. I am seeing on the internet there are many complaints about this and there was a recall? But they have run out of replacement parts??? Never received any recall notice. We have online instructions on how to repair and have done this many times and the rust comes back. About a week ago we sanded, primed and enamel painted the area plus I have put NO BLEACH in the dispenser and the rust is coming back. I hate to replace a working machine but this rust can and will get on my clothing. Whirlpool was the absolutely best in the past but this one is a lemon.

It does not clean properly, if the dishes are not almost totally cleaned before putting them in the dishwasher. It has stainless steel inside, but the plastic holders have all had to be replaced. It is a large dishwasher that holds pots and pan. It is plain and has nothing outstanding to look at. Dishwasher are not meant to last any longer than 8 years, I have been told by a repairman. I will never purchase a KitchenAid, made by Whirlpool again!

I bought my Whirlpool Duet set with pedestal in February 2008. I just had a tech here to figure out why my machine is so loud during agitation and that I cant hear anything else. He said its the drum hitting something. I never overload my machine - just normal use for 4 years. It costs more to repair the machine than to buy a new one. Now, after seeing this information, Im not the only one who has this problem with my Whirlpool washer. I am disappointed that there isnt anything else the Whirlpool company tech can do for me - just a receipt that shows the parts alone cost $600.00. Now, I have to pay about $50.00 just to get rid of what from the outside looks like a perfectly good machine.

We bought our dishwasher April 2018. This morning I noticed the paint had bubbled above the heat vent (area 3x 1/2). Upon closer inspection, the the paint was also peeling. We called the company to see if they would replace the skin but the agent said the only thing they could do was send us touch-up paint. The door is considered cosmetic & only covered for 30 days. If we wanted to replace the door panel, we were welcome to buy one from them. However as this seems to be a manufacturing defect, we would be replacing the door every 16 months. When we realized whirlpool wouldnt back their product, my husband looked a little closer to see what needed to be done & found that it had rusted under the paint & painting on top of rust will adhere properly.

I have had a lot of washing machines in my life and trusted that Whirlpool would have good products. Well, with this top-loader, I couldnt be more wrong! I have never had a machine that just sloshes clothes around - at best - leaving them just as dirty! Our water bill has greatly increased on top of that - I AM SO VERY DISAPPOINTED! Unfortunately I cant return the bad merchandise since I bought at a Scratch and Dent store (just a dent on the outside does not interfere with performance...).

Bought Whirlpool 30 gal propane water heater in Feb, it lasted until May before the unit died. Paid for the extended plan warranty (NEVER do that!). Called support and they said they could send someone out in a little over a week (week with no hot water). The week goes by and on the day it was suppose to be repaired the guy calls and says his van broke down (this was a Friday, getting that early weekend). The earliest they can reschedule is in another week (over 2 weeks no hot water). Called Lowes to see if I can just return it (extended plan and all), no, you need a return code from the whirlpool customer support. Call the Whirlpool number again to ask for a return code, no, it is a repairable problem (even though no one will come repair it). Lesson learned, will never buy Whirlpool or anything over $50 from Lowes again.

I am very impressed with Whirlpool. After seeing my review, they contacted me and offered to send the parts to fix the problem with the LED lights. They sent a Whirlpool authorized repairman to my home with the understanding that since the refrigerator is out of warranty, I would have to pay him. Whirlpool also asked me to return the faulty part so they can research the problem. We are once again happy owners of Whirlpool products. Thank you Whirlpool!

I bought Whirlpool water heater model #FG1H5040T3NOV about 5 years ago. Burner assembly was replaced two years ago and now, thermocouple was replaced yesterday.

We purchased a Whirlpool Cabrio Washer in 2010. I have had nothing but problems trying to wash black/dark clothes, it leaves white stuff. I assume its soap scum all over the clothes. Ive tried cleaning the machine with Refresh more often than recommended and it still has the same problem.

I have a portable dishwasher. It does not dry the dishes when cycle is completed. I have to either leave the door open or take them out and towel dry them.

So after having the old white standby refrigerator and stove from the late 1970s, I figured it was time to upgrade. I have had theses appliance for TWO MONTHS! And they are starting to rust! I dont want to complain, I want a solution. Is there a law suit or advocacy to get our money back? I even bought the 5 year warranty, but found out that it is considered cosmetic!

We purchased a Whirlpool Cabrio washer in 2009. It makes awful sounds during the draining and spinning cycles, has started leaking in the past month and now, several error codes and will not finish a load of laundry. We have a family of eight and thought that we had bought a very dependable product for what we need. Boy, we were wrong!

The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.

Whirlpool Gas Range Model WFG524LAB0 - Purchased on 09/2013. Product works well but noticed back in July 2014 that cook top was not cleaning well. Did not mind it that much thinking it was just baked on grease and would just do a general cleaning when I get to it. After the holidays and now getting around to clean the range top, I discovered the cause of range top not cleaning well. The porcelain was chipping away.Today I called Whirlpool customer to complain and see what they do. They replied that it was just a cosmetic blemish and that was not covered under warranty. I told them that that cosmetic blemish lead to rusting and eventually result to failure of the product. They also said it was out of warranty but was eager to have a tech come over to check the problem out for additional fee.

I have a Whirlpool gas water heater that failed after only three years of operation. My previous water heater in the same spot lasted 18 years. The problem is a defective thermo coupler design that burns out if a filter you cant access isnt cleaned every three months.

The Weatherization program installed a whirlpool refrigerator in our home in October 2012. The fridge is less than 2 years old and the blower fan went out. We lost most of our food (what wouldnt keep in a cooler) and my daughters insulin spoiled. When they put this fridge in, they took our old one saying it was less efficient. Now we are stuck with a fridge that doesnt work and is out of warranty at less than 2 years old. We have left several messages for a Whirlpool representative to call us back and here we are, one week later, and no call back.This is frustrating because although the fridge we had may not have been as energy efficient, I am almost certain that it would still be working. I have never heard of a fridge that lasts less than 2 years. Also, we know that the blower fan must be a common problem because they are back-ordered approx. one month. We checked online, and called local businesses and not one place has the part available.I think we at least deserve a call back considering how stressful this has been on us. I had just spent all of my grocery money for the month, and 70% of it went bad and had to be thrown away. Money is tight for us and replacing spoiled food is not an option. Also, the insurance company denied our request to refill my daughters insulin a little early. Without proper refrigeration the insulin goes bad. The insurance doesnt replace lost or spoiled medication. Guess we get to pay for that too! Thanks so much Whirlpool! Ill be sure and highly recommend your products to my friends. (NOT GONNA HAPPEN.)

I purchased the Cabrio washer/dryer in 2006. We have had it repaired 6 times and I even purchased a two year extended warranty after having issues with it the first year. Now I seem to be in the same boat. The washer will not spin and drain. This has already been looked at by a technician several months ago. I feel like this product is faulty and has not worked properly from the start. Are there lemon laws for appliances? It seems that this product would qualify. I will never purchase Whirlpool again.

Extremely quiet machine. I love that the silverware wrack is situated across the front of the door giving plenty of space for lots of silverware. This leaves even more room in the already large washing area for pots, pans, dishes, bowl, glassware & more.

I purchased Duet washer 3 years ago, but it wasnt installed until a little over a year and a half ago. Machine started making loud noise during spin cycle, and eventually would not spin the water out of the machine. I contacted Whirlpool and was told there was a defect in that particular WP model and if it was confirmed by a provided tech, WP would provide the parts for the repair. The tech confirmed the problem, and I was told the repair would still cost over $450, even with the free parts. When I approached WP and asked them to fix the machine since it was a known defect, it was denied that there was a defect.

Bought appliance (Whirlpool French Door Refrigerator Freezer) in 2014. The seal that closes all the brackets with screws and you had to hand guide it to close. Then the freezer got out of alignment and wouldnt close and seal. Ice built up behind drawer which prohibited the opening of freezer drawer. Wouldnt open more than 5 inches on one side and 3 inches on the other. Had service tech out. Cost almost $200. Did not get French doors repaired because the part cost over $125. Less than a year later I have to have a repairman back out for same problem with the freezer door and ice build up. Not happy.

Whirlpool Water Heater FG1F4040S3NOV - I had this water heater installed in 2005 by a professional plumber and every year since like clockwork, I have to replace the gas control valve/thermostat. Last year, Sears came and did the work and made their arrangements to have the part replaced. This year 2012, March 9 my gas control valve went again. The unit is not even a year old and broke again. Unfortunately, the six-year warranty is up on the hot water tank. I called Whirlpool two times. The first time, the guy told me that the warranty was up and hung up on me! The second time, the guy would not honor the replacing of a part that is not even a year old yet. The money I spent over the six years making repair on it, I could have bought a new one. This company is nothing but a bunch of **. Is there anything that I can do? I have paid to replace this five years in a row.

Oven was purchased new from Home Depot. Right off, the top black glass surface got scratched. Not sure how it happened. Seems to scratch easily. Then, the oven temperature for baking was found to not hold consistent. While pre-heating the oven for 350 F, the temperature goes up to 375 F, then well into the baking time, can drop to 100 degrees less (275 F). Oven feature is called accu bake. It ruined the baking and seems to be anything but.

Whirlpool N50T61-403 - I bought this thing today 8.21.14 from Lowes. It is a Whirlpool 50-Gal water heater (6th sense) and was going to have it installed by their installer, but elected after seeing it was very similar to lining up with my old unit. I got it in and then filled it. After filling, I lit the pilot light per the instructions then turned the knob for heating it up. Success, the flame spread across the burners...then went out. The steady blink changed to the 2 blink code indicating a bad thermopile. It did not work - right out of the box. No plumber near me carries the part. Whirlpool has thus been pretty good about it offering to have someone come out at their cost... But if no one has the parts, that is no good. I am moving from this house so if we can get it to work, its the problem for the next owner. If not - Ill have to get an RMA and go back to Lowes... Then try the Rheem from Home Depot. Will see if they will overnight a part tomorrow. I found the other reviews - and I dont like it that this thing appears to have difficulty right out of the box.

Bought new dishwasher on 11/29/2013. Model #WDT710PAYM. The top rack cannot hold much weight. It keeps collapsing. One side keeps falling out of the track. Had man in for repair, still doing it. They sent me a new rack and rollers, still doing it. Having repair man come back again in a few days. I am so disappointed with Whirlpool. I cant believe they went so cheap in building these machines. I gave away a whirlpool gold that was 20 yrs old and it is still going strong with no problems. I just wanted to update up kitchen with stainless steel appliances. I will never buy whirlpool again!! This cannot be fixed. It just doesnt fit tight. Im stuck with a bad dishwasher and shouldnt be.

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

My Whirlpool electric range has been a nightmare! I bought this thing 5 years ago and I am having it replaced on Saturday! It had a cleaning thing where I put in distilled water and 20 minutes later I could just wipe it out. Not true. I had to use oven off??? Next the oven would not work. Learned if I turned off the power it would reboot itself! The next thing it did was all on its own it turned the temp. from 250 degrees to a full BROIL. The oven now will not heat up to 350 degrees! I just blew $1200.00! On the other hand I did buy a Whirlpool fridge. It has been awesome!

Sounding like a broken record, this washer is such a disappointment! I had high hopes for this top loader and thought I did enough research. Bought a Cabrio in Oct 2016 and have never liked it. They will have you believe it’s your fault... the wrinkly clothes, the clothes not clean enough, the white marks over all your clothes... you can’t change your detergent or softener enough and change the amount enough... it will still be there. So disappointed??? Want my front loader back!

My Whirlpool is reliable, however it does not have a soaking cycle which I would enjoy having. It also has an unbalancing problem when speeding if I attempt to wash heavy loads on the extra large load cycle. However, it responds very well on large loads for heavy washing. Shortly after I got it the timing had to be replaced, but no problems since then. Overall pound for pound for the dollar it is a good machine.

Our Cabrio washer often ties clothes into (unwashed/still dirty) knots. They are so bad that it takes several minutes to untangle and then the load has to be rewashed. It also has to be set for hot water when you want cold, and vice-versa. I am unable to do that for the rinse cycle, so all our clothes are rinsed in hot water. It doesnt even get the clothes clean, when it doesnt tie them up. Ive gotten used to it sounding like the space shuttle taking off and managed to shut off most of the annoying beeps. The dryer is almost as bad, it seems to take a long time to dry clothes, and they come out very wrinkled, even on the wrinkle guard. The finish isnt even good on either one. It scratches very easily, and scratches start to rust almost immediately. This is quite possibly the worst piece of junk my family has ever owned, except maybe for an unfortunate experience with a 77 Dodge Aspen. We bought this set thinking we were paying enough that we were getting the best. Never again!

I would not recommend this product at all, nor would I recommend the Whirlpool Company. This washer was over $1200.00. Within two weeks of purchase, I had to call a service repair company as I was immediately having issues with the washer not draining. Being a front loader, this machine required using the appropriate HE detergent. I followed the instructions, used the appropriate products and had nothing but continuous problems. It is a (lemon), and very frustrating, as it does not seem repairable. No serviceman could give an appropriate reason as to why the washer would not drain, nor could they figure out why. It didnt matter the size of the laundry load or the type of items...towels, jeans, or silky delicates...the washer failed at turning from the wash cycle to the drain cycle. It also leaked because of the lack of draining, and began building up a mold film and odor even though I consistently wiped it dry and left the door opened when not in use. I received no assistance from Whirlpool and was given the runaround and told I must be doing something incorrectly.

Purchased an expensive, Cabriolet Washer in 2014 to replace a well used Kenmore washer. Sucked into the, Whirlpool is a good brand and spent more than I would have. Lid lock fault started about 3 months ago, googled fix and found this to be a very common problem with this brand. Have been able to override and reset it but it is very frustrating to deal with. Called in a repair person this morning who, for $140 told us we had a faulty lid lock and for $360 he would replace it. I contacted Whirlpool and asked if they were aware of this very common complaint (just google it) and they were not but offered to make a record of mine. Please do not buy Whirlpool. Very disappointed with their product and their response.

The capacity is small but it does a good job of washing and drying the dishes. I always check to make sure that all dishes are washed including silverware and they are. My dishwasher is quite old but it is still sufficient for our use.

My first time with Whirlpool (Always had GE) but at the suggestion of our builder, we went with Whirlpool and the stainless steel is horrendous. Nothing will clean it or make it look STAINLESS. My refrigerator, dishwasher, double oven, tall vent all look terrible no matter what I use! I have never had this problem before. Im embarrassed to have anyone go into my kitchen...

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

Watery body from all the refrigerator side since 9 – 10 months and complained to Whirlpool 2 months back. They changed the thermostat 2 times but no use. Problem same. Please help. I complained during the last warranty days. Please let me know.

Whirlpool Duet Sport W & D purchased from Costco in mid 2007 for $1600. Costco gives an additional one year warranty, totaling three years. Both have worked exceptionally, I must say -- clothes come much much cleaner, keep their color, and last much longer vs. top loaders (Im sure the water softener helps). Two separate techs just confirmed the circuit boards went on the washer ($450 with labor) to replace. Washer looks brand new, but now will be going to the curb.

Our new fridge, which was already an exchange from another unit that went bad, kept freezing things in fridge compartment. A tech was sent out three times and then the compartment quit working completely. They stated they would replace for us, only way they would replace was to have them ship a new unit which would take two weeks. So we are without a refrigerator for two weeks. Asked if I could go buy one and be reimbursed. I could but I would NOT be reimbursed for full amount. The company reps I spoke to could have cared less about our situation especially Fred who supposedly is a supervisor. Do yourself a favor...DON’T buy Whirlpool. Their customer service sucks!!!

I bought the Whirlpool Cabrio model # wtw5500xw2 about two 1/2 years ago. Besides my clothes not clean, I havent have any problems with it until recently. Usually it doesnt spin. The clothes are left soak and wet. First the belt broke, then the lid lock, then the nut came off the pulley, then the splutch assembly. There was a few more problems in there. Now who knows what is wrong with it? It is one problem after another. It is a money trap. The CEO was just after money. There needs to be one big lawsuit against Whirlpool. After I find out what is wrong with it and the cost to fix it, I probably will just go buy a new washer/dryer set. And it will NOT be a Whirlpool.