My Whirlpool Cabrio WTW5550xw0 has had many problems. It started with the lid lock error, replaced it, lasted about 2 weeks, and got another one. I did the diagnostic test that pointed me to the actuator, replaced it. It worked for 2 weeks, got another one, and then another one. I was getting a bad reading from the control panel, replaced it, and that worked for a while. I found out that the actuator had a little water drops on it. I figured that it must be the tub seal, so I replaced it. That lasted about a week and a half, and it started dripping again. Now, I figured it is that the transmission has bad bearings, that causes my tub seal to leak, that causes water drips to go onto my actuator, causing a failure in that, which can give me all kinds of bad readings on the diagnostic test. I have replaced at least half the cost of the original purchase price on a year and a half old washer. I also bought my son a Whirlpool Cabrio washer a few months before I bought mine, and he hasnt had a single problem.

Whirlpool is the manufacturer of most appliances including the Kenmore dishwasher. Your products are made horribly for the mother board to go out in 2 years is ridiculous. I purchased a stainless steel dishwasher from Sears in August of 2014. 2 weeks ago I received error codes E2 and F2. A technician came out and the mother board needs replaced because water got into it... its a dishwasher. The cost to fix $465. I paid $673. The sales person informed me that I should have purchased the extended warranty because the appliances now only last a few years. Seriously... fleecing of America. This is my last purchase from Sears. We have bought appliances for 30 years from Sears and this is the end. They could care less about customer service or their products. Apparently everything is now made by Whirlpool who will also be getting a review. Shame on you for making poor products.

My Whirlpool Cabrio washing machine. f1 keeps showing up on washer on. Shuts off again and again.

Piece of crap. We built home 2 years ago and have all gold series appliances! They are all CRAP. Wish we would’ve upgraded to KitchenAid. Dishwasher won’t wash, microwave has hot spots and has to be unplugged and plugged back in often to work. Freezer side of the refrigerator will stop making ice because it freezes up often! NEVER buy Whirlpool!

August 26th 2014 purchased a NG (NO GOOD actually natural gas) Whirlpool water heater from Lowes. Model No. N40561-403. Installed it and everything was fine until this morning August 29th 2014. The indicator light was out and so was the pilot. Tried to light it without success. Called Whirlpool and they are sending me a new controller that now needs to be installed. Called Lowes and they will not take it back. Wish I would have found this site prior to this costly fiasco. Waiting on part now and I will keep you informed as to my progress. I have a feeling this is going to be 2 days wasted and $367.00.

I bought the Whirlpool Cabrio model # wtw5500xw2 about two 1/2 years ago. Besides my clothes not clean, I havent have any problems with it until recently. Usually it doesnt spin. The clothes are left soak and wet. First the belt broke, then the lid lock, then the nut came off the pulley, then the splutch assembly. There was a few more problems in there. Now who knows what is wrong with it? It is one problem after another. It is a money trap. The CEO was just after money. There needs to be one big lawsuit against Whirlpool. After I find out what is wrong with it and the cost to fix it, I probably will just go buy a new washer/dryer set. And it will NOT be a Whirlpool.

I am writing this complaint because of the very poor service of Whirlpool. My washing machine broke after 1 year of use. Luckily, I was on my 2-year insurance. The wiring fully collapsed and I needed to change the whole drum. I called Whirlpools customer service and they said that they would fix the problem after 2 weeks. They came on the day and found out the problem and ordered a new drum. They said they would fix it up on the 5th of December, and it has already been over 3 weeks. On the 4th of December, Whirlpool called me and said that the item they had ordered for me has been damaged. I am not satisfied by these products because it is only a drum (it cant break that easily). I cannot recommend this company to my friends and family due to the quality of the products and the poor customer service as I was waiting on the phone for almost an hour trying to get through.

The door can be slightly open on the model GSC25C4EYY02, and the alarm will not register. Ive come home on too many occasions to find the food no longer at a desirable temperature. Im very bummed about this refrigerator choice. The refrigerator door open alarm is useless.

Whirlpool Gold Fridge - For all the people who have water collecting at the bottom of their freezer... There is a plug in the drain pan underneath that needs to be removed. It comes that way from the factory. Thank God, I have a smart Hubby and Father-in-Law. I find it INSANE that these Repair people have not caught on or do they just want to keep billing for Service Calls.

It is a really great microwave, but the door is falling off of it. We can still use it, but try to be careful about it. I honestly and truthfully love my whirlpool microwave as well as my whole set of whirl pool appliances. The door is trying to fall off, but we can still use the microwave. If we get another one we will probably get another whirlpool because I love it so much.

We bought our Duet washer in 2007 with a three-year warranty. In 2010, the washer started banging so we called it in for repair. It was determined that the bearing on the drum was bad, so the entire drum assembly was replaced because the poor design of integrating the bearing into the drum. Almost one year to the day, our washer started banging again. The washer is no longer under warranty. We were told the parts are around $400 plus and another $400 for labor.The repairman was from the store we bought the washer and he is a certified Whirlpool repairman. He related to us that this is a very common occurrence for Whirlpool washers because they are using cheap foreign made bearings. He services this problem on a weekly basis and Whirlpool will not do a recall because unless it is a safety hazard, it is not a concern to them if consumers have to pay out the nose for cheaply made parts. This repairman informed us that during training at a Whirlpool class, he learned that on the main board of the washers, they could put a 2 cent lamp that would indicate a bad board which would simplify diagnosis, expedite repair and reduce service time, but Whirlpool wont do it because it isnt cost effective. The repairman told us that we can call customer service until we are blue in the face, but Whirlpool wont give a ** because it is out of warranty. He sees this happen all the time with Whirlpool. My wife called Whirlpool Customer Service just to be told we are ** even though the cheap, crappy bearing that went bad was done under warranty, a year earlier.Well Whirlpool, I guess you lost another customer who will make sure that you lose a lot more customers. We are going to take our business elsewhere and we will make sure all our family, friends, neighbors and coworkers know how bad your customer service and poor attitude is toward consumers. If you cant back your products when you put cheap foreign garbage parts in your product, then you need to lose business and get out of the market.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

Got a simple error code E6 F2 on the display of my oven (only 8 years old). Called Whirlpool to schedule a repair. They told me there were no available dates for one of their techs to fix my unit. They referred me to 3 outside companies that wanted to charge me over $100 just to come out and take a look. One of the phone numbers to the companies they referred me to was a wrong number. I asked them to tell me what the error code means and they said they couldnt tell me with any degree of accuracy. (What use is an error code, then??!!) I checked all over the internet and different websites say it might be a control board (over $300 for the part) issue. But several techs also said that it is a crap shoot and could also be a Temperature Sensor. I called back Whirlpool to see if they could get me a deal on the part. But, guess what? They dont sell it anymore...in fact they dont even sell their own parts at all!! And, they transferred me to some outside company that refused to even give me part numbers, to avoid me shopping for a better deal (which I did end up finding on Amazon after number 6 below). I called back Whirlpool and after getting transferred around to 2-3 different people and wasting about an hour I finally got someone who finally wanted to just give me whatever decent service they could and they finally got me the part numbers of the 2 different control boards (Main Control Unit and Sister board that controls the locking mechanism, $367 and $140 respectively). Now I am faced with paying an Appliance Repair person over $500 for what seems to me is a BIG FAT LEMON of an appliance due to the sheer number of unsatisfied people that are having the same issue, have had it fixed, and had the error just return again. THUS.... WHIRLPOOL AND THEIR CUSTOMER SERVICE AND THEIR PRODUCTS JUST SUCK!! AND I WOULD NOT RECOMMEND THEM TO ANYONE! THE LEAST THEIR COMPANY COULD DO IS TRY TO HELP FIX THE PROBLEM, NOT EXACERBATE IT BY GIVING SHADY CUSTOMER SERVICE AND REFUSING TO HELP FIX THE PROBLEM!!!

Near 3 years ago we purchased this side by side going by how good Whirlpool products are supposed to be. Recently the bottom freezer started frosting up and not clearing. Tried all suggestions in the manual. Could not find any information online. The manual was useless. I went online to Whirlpool support 3 different times asking for help. Never got a reply. The racket it made was driving us crazy. It short cycled since it was frosting up. Set up an appointment online. They got that correct and responded quickly. Go figure. The tech came was very nice & professional. No warranty. Find out they only provide a one year warranty. That is absolutely nuts. A refrigerator should last 15 years with no major problems. Should not have needed a $500.00 extended warranty for a $1,300.00 refrigerator. Turned out 2 components needed replacing. Cost just over $400.00. Now were worried it is going to fail again in who knows how long. Whirlpool used to be a respected brand. Never again will we buy a Whirlpool product. 1 year warranty show you they know how cheap they are building their products.

I have a Whirlpool refrigerator from 2017 that is causing so many issues and finally completely broken after spending $500 on repairs. 4 months ago, refrigerator was making loud noise and freezer wasnt working. Then within a week the whole unit stopped working. Then, freezer got all frosty and the whole unit got shut off. 2 month later, the ice maker stopped working and nothing is working now. I called the Whirlpool and they offered me to purchase extended warranty for $530. I could not believe they wanted me to spend another $530 on this refrigerator after spending all this money on repairs and still useless. I refused to buy any more Whirlpool product that I used to love in the past. I am just so disappointed with the customer service as the supervisor from Whirlpool said that is why they offer extended warranty. $2000 refrigerator to last me 3 years???? Not doing this again.

I have had my Whirlpool dishwasher for 8 years..I cant use the top rack anymore as it doesnt clean dishes!! I bought a brand new one for my cabin..I hope it works longer (right now it cleans amazing).

This product deserves ZERO stars! I purchased a Cabrio washer - dryer in October, 2013. I have carefully followed the instructions for the washer. I am hugely distressed about the large amount of money I spent on a washer that is absolutely terrible, horrible, awful., no words can adequately express how bad this so-called washer is. The low-water washing has torn up all of my new towels in the matter of a couple of washes. It has completely ripped out the hems of the towels and pulled long ragged strings in the towel. And these were not cheap towels. I am mad at myself for not researching better before buying. I hope my complaint can save another consumer from the misery I am suffering because of this shameful product.

This refrigerator (Model #wrf560seymoo, Serial # VS31343718) was new in April 2013. In the last 3 years it has required 3 service repairs. Two under the extended warranty, one recent one 3 months out of warranty. All repairs came up in the last 3 years. The first repair addressed frost build up in the freezer. The second required replacement of the water filter compartment and the third will be addressing water dripping from the freezer door when I open it. Even after turning off the ice maker and removing the frozen puddle from the bottom of the freezer, it still drips water when I open the door. I have a call into service on this right now. I would like the company to fix the current issue even though it is outside of warranty. This product is too new to have so many problems and be just over 5 years old.

I have called Whirlpool six times to request a replacement for a broken deli drawer in my refrigerator. I was told to throw everything away from the unit, since the whole assembly would come complete in the mail. First call: Ordered the replacement: what came was a glass shelf without a drawer or gliders and hardware. Second call: requested the drawer and remaining parts. Third call: only received the plastic drawer without any means of installing it. Fourth call: received only one side glider, again without hardware to install. Fifth call: requested a supervisor (Kimberly) who took the order for the remaining glider and all hardware. Received second glider and (1) screw when two are needed.Sixth call: asked rep Brigitte for a supervisor and was not connected. Given the run around and told that the rep spoke with a supervisor for me and would send out a repairman to assemble the unit. I just need the missing screw. I have spent a lot of time on the phone trying to get what I need from Whirlpool and do not have time to wait for a service repairman to come out. I just cannot fathom how that many calls - with me being patient and calm - cannot produce the required items. Horrible.

I bought Whirlpool top-loading high-efficiency low-water washer Sept 2018, model WTW5000DW, Serial # C83444466. Worst washing machine ever! No matter which water level you choose, it will not dispense enough water to cover the top of the clothes load, therefore the clothes are just moved from side to side with only the bottom layer of clothes getting wet; top clothes stay dry. Not enough water to fully agitate to clean the clothes!Whirlpool serviceman came today (Jan 13, 2020) to recalibrate the settings. VERY NICE MAN BUT THERE WAS NOTHING HE COULD DO TO SOLVE THE LOW WATER LEVEL. Recalibrating settings did nothing to solve the problem of not enough water. I am 81 years old and I have to manually add at least 4 buckets of water to an average load of clothes. This is unacceptable. Wont someone please initiate a class action lawsuit against Whirlpool for selling this very obvious poorly designed machine? NEVER EVER BUY A WHIRLPOOL WASHING MACHINE. It is a waste of money.

We have had this Refrigerator for 3 years in December of 2016. To date, we have had to call a repairman (in February 2016) to replace a circuit board on the back of the refrigerator. That took 4 days, as the company sent the repairman the wrong parts. After that $300 repair, which we got at a discount because, the repairman felt bad that the company actually sent the wrong part. Since then we have taken it apart ourselves for several reasons: The freezer compartment filled up with a layer of ice and started to melt all over the floor, shutting the refrigerator off, (which then forced us to borrow coolers to store the food) until it could be repaired. The drain tube was completely blocked and in order to fix this problem, the tube had to be taken out and modified, according to the Internet videos we then watched. In order to make all of these repairs, the door, the shelves and baskets have to be removed, which is definitely not an easy thing to do at all.There are so many hidden screws and tabs that must be manipulated with tools and by hand to remove the doors, shelves and trays just to get where you need to be in order to make these repairs. With each repair, the ice maker and water dispenser started having problems, because, each time the refrigerator has to be shut down, it takes hours for it to re-set itself. Luckily my husband had the tools necessary, with videos on the Internet to assist us. However, once the first problem started, it was a snowball effect, literally. ALL of these problems have been identified by the manufacturer, however, nothing has been done. VERY POOR DESIGN!

This is NOT a true review of the oven as I have not used it for baking yet. I just wanted to make a comment about my new oven which was installed this morning. I turned it on as instructed and heated at the high temperature to rid it of the odours. When it is turned completely off the cooling down process begins, which blows the hot air from the oven into the room, causing some annoyance from the hot air, as well as the noise. Not sure I am going to be so happy in summer. I am certain it is a wonderful product for baking results, but with this annoying feature, I am not feeling so happy about it.

I took the time to read the owners manual, and then ran machine (washer wtw5000dw0). Using an affordable HE approved detergent (Xtra), I had no problems. If the washer doesnt fill or drain correctly, look up how to recalibrate it, was easy to do because I did that after transporting it. My clothes are cleaner, and I am using LESS detergent!

Whirlpool Washing Cabrio machine model WTW5500XW0 - I purchased this machine five years ago. After about a year I started having problems where the clothes were not coming out clean. I contacted Whirlpool and was referred for a repair. The repair man told me these newer machines need the Affresh product to clean out the machine so this doesnt happen. I bought the Affresh product and there is still a problem. Every load of wash has to be put back in for another rinse cycle, sometimes two rinse cycles. Its ironic because the cover of the booklet for the machine says low-water washer which was the selling point to buying this machine. Instead of using less water, Im using DOUBLE the water.

I have had an extremely frustrating experience with Whirlpool refrigerator WRT311. It broke after 6 months. So far it has been diagnosed twice with a faulty compressor and leaking coolant. Whirlpool will (seemingly) never replace an appliance--even if it makes no sense to keep trying to fix it. This is a $600 refrigerator! I cant imagine how much they have spent in repair costs. They simply send a service tech time after time, jerking the consumer around with no regard for what we have to go through to arrange 6 tech visits, some of them multiple hours long. Yes, we have had six tech visits, for a total of 10+ hours, and six weeks living with a broken refrigerator. As well as 30+ phone calls, hours on hold, etc.The refrigerator is loudly throbbing away after being refilled with coolant twice, and is still leaking coolant. Are they hoping the customer just gives up and buys a new appliance on their own? I wonder about the many positive reviews of their appliances: Are they fake? Are they churned out by Whirlpool? I have no confidence in this company. They are inept, if not crooked, and I would advise buyers to beware of poor quality and extremely poor warranty and consumer service.

Bought a whirlpool water heater less than two years ago and it has already failed. I could not find parts for it and was told by a lowes employee that I would have to call whirlpool on the 5th of July (three days away) to order any parts. I tried three plumbers in the Indianapolis area and they all told me that I would be better off replacing it with a different brand. I just put in a new rheem in its place. I will never buy another thing from whirlpool. They are no good.

Me and my wife bought a Whirlpool top load washer June 2011. Two months later the motor locked up and they repaired it; then the transmission started whining the next month. It was repaired. Now a bearing is going out all in the first seven months of ownership and they will not exchange washers, they just want to keep fixing this one until the warranty runs out. Whirlpool washers are a piece of junk and I will tell everybody not to buy anything Whirlpool.

I am very happy with my Whirlpool appliance- oven. Ive had it for almost 5 years, with hardly any issues. -Its very user-friendly when I need to program any cooking instructions. Both the elements & the actual oven cook everything to a perfect.

Had the entire kitchen remodeled. We bought a Whirlpool Gold French Door refrigerator from Sears, did not buy an extended service contract. The refrigerator has NEVER made an ice cube. The water dispenser in the left door sometimes works, mostly not. The fridge freezes the food inside, temp. set at 41°F. The entire ice maker has been replaced, several valves have been replaced, a service company rep. tore the back off the fridge, found some insulation misplaced, said he repaired that. We have been very patient. Three repair companies have been sent out by Whirlpool, two said the refrigerator CANNOT BE REPAIRED. Whirlpool told me the only resolution is repair.Whirlpools Customer Experience Center is a joke, they do nothing but try to schedule another repair call. Tell you how sorry they are about your problem but do nothing to solve the problem. Carefully trained to give you the BIG runaround and nothing else. You never get the same person twice or the same city twice. Patients exhausted. Calling my lawyer. I would strongly advise anyone needing a new refrigerator not to buy a Whirlpool product. You should also check the list of other brands they make, there are several. I wouldnt buy them either. Buy a fridge made in Japan by a Japanese company. They get it right and know the Quality Process.

We bought a Whirlpool French Door refrigerator in July of 2018 and it has gone out twice (quit cooling and has completely frozen over). The first time it went out at 6 months and the second was two days after the factory warranty expired (the warranty for the Whirlpool repair company lasted only 90 days for parts and labor which is useless). I’ve called the company to come take a look and it will cost over $100 just to have someone come out since we are outside the factory warranty window by four whole days. I was basically told there is nothing they will do even though the same problem keeps happening. This refrigerator was brand new and didn’t even make it six months.Now we will need to either pay hundreds of dollars for repairs (knowing that the issue will likely happen again) or buy a new refrigerator. Even though we have barely had this appliance a year. I will never, ever buy Whirlpool products ever again. I also posted my negative rev on their official website and it never got published. They only show their 4-5 star reviews (all of which say the customer has been incentivized in some way). This is a misleading and sneaky process.

I purchased a whirlpool gold series microwave model #WMH76718AS one and a half years ago, paid $500.00 for it. It stopped heating. Everything else works on it so it looks like I paid $500.00 for a digital clock and a fancy bread box! I went online and read complaint after complaint that the same thing happened to other people. It appears that the magnetron is faulty. I called Whirlpool and asked their service rep how she would feel if she bought a microwave and after 1 1/2 years it wasnt working. She told me that it was man made and that I should EXPECT things to go wrong. She did offer to pay for parts... which did surprise me. But I have to pay for a $45.00 service call and all labor that it costs to fix it. I called the number she gave me and got a answering machine.... still waiting for them to call me back. I most likely will just throw this Whirlpool piece of junk in the garbage where it belongs. I dont want to spend hundreds of dollars to repair a lemon. I feel that Whirlpool knows there is a problem with their product... that is why they offer to pay for parts. But why should their mistake cost their customers money on top of all the inconvenience. Whirlpool does not back their products or care about their customers after they get your money. I will Never buy a whirlpool product again and that includes anything from their sister companies Maytag, Kitchenaid, Jenn-air, Amana and there are many more. So before you buy anything make sure you check to see who you are really buying it from!

Smelled strange odor in laundry room area.. Noticed plastic panel to Whirlpool electric water heater controls was melting and immediately closed breaker to the heater.. After inspection of heater control panel, noticed all wiring damaged and burnt causing burning smell.

You have to take into account that this microwave doesn’t heat up as others I’ve had so even if the instructions call for something to be cooked for 5 minutes, you have to add at least 2 minutes more. If not it would be undercooked.

I purchased the Energy Smart Gas Water Heater about a year and a half ago, intending to install right away as part of our upgrades. Just now, I was able to install this replacement to our 30-year-old water heater that was showing problems. When trying to start the unit, I kept getting the response that the lower sensor unit failed. We contacted plumbing companies. We were told they would not work on any Whirlpool models purchased from Lowe’s, because they were the worst hot water heater ever made. I called Whirlpool support. They wouldnt put me through to a tech support person until I was registered in the system. I gave up trying after many minutes of frustration.

Ill be just as responsible as Whirlpool and Nasons has been... I bought my Whirlpool stove less than 2 yrs ago from a reputable business in a nearby community, CROWN POINT, INDIANA! I have had trouble w/ the burner knobs ever since I bought it...just brushing up against them turns them on. Enough gas escapes into the kitchen... I bought knob covers to prevent that (they did NOT work)! So I called the place I bought the stove from and they sent out a repairman...he said there was no fix for it... but that I owed him $69.99 for the service call. And every time I turn the oven on to heat it to bake something you smell gas also... Im almost afraid to use it... 3 nights ago I woke up to the kitchen filled w/ gas...knob covers on but still one was still on a bit... it was a whopping -25 and we had to open windows to clear out the gas... you shouldnt have to check the knobs once youve turned them off. Nor should they come on when you brush by them...when youre not even cooking... Granted I am short but the serviceman said I should move everything I needed to cook w/ closer to me so I didnt have to brush up against the stove... what????? I have cabinets above and all around the stove. What I cant use those cabinets????? Something is terribly wrong w/ the stove and the service... If youre in the market for a new stove, dont buy a Whirlpool and for certain DONT buy anything from NASONS appliances in Crown Point Indiana... They along with whirlpool dont stand behind their product... They told me they never had that complaint before. WRONG, I read it more than once on this site...liars all of them!

Before a year was up after purchasing 4 Whirlpool appliances for our kitchen, our refrigerator needed a new compressor. Of course, they covered the cost because it wasnt a year old yet. After much complaining, they gave me a whopping extra 3 months coverage, until Jan. 2014. Now we have water leaking on the floor and ice collecting on the bottom of the freezer drawer. What a piece of junk! I had sent an e-mail to Whirlpool after the compressor situation telling them that I would never buy from them again and would have nothing good to say about them. No one responded. Goes to show that Whirlpool could care less about their customers satisfaction. Never again will I buy anything Whirlpool makes. By the way, our old frig is in our mud room working absolutely fine.

Whirlpool Duet - Front loading with additional base makes loading and unloading easy. We have had the washer and Dryer about one year now. They were replacements for Kenmore front loaders. We replaced a Kenmore front loading pair that served us faithfully for more than ten years. But when we purchased a new house we decided that it was necessary to upgrade to better units. The Whirlpool Duet pair has performed exceptionally well with one little caveat. Periodically we have to unplug the units to reset the computers when they dont function properly. Small problem, easily solved.

This machine always leaves me questioning if its going to finish the cycle. It goes thru all kinds of spastic sounds in order to advance to the next step. I learned I cannot presoak a load more than 10 minutes before the machine empties ON ITS OWN! I just dont trust the machine and would not buy again.

Whirlpool Cabrio washer w103386894 - I have had nothing but problems with this piece of crap washing machine. Either the clothes come out soaked at the end of the spin cycle, or it gets stuck in a cycle and repeats. It makes so much noise you can hear it through the whole house. It is less than three years old and now it is leaking water. I had a base model Sears Kenmore that I had for over 12 years and it died from old age. This Whirlpool is pure crap, do not buy.

We have a Cabrio washer and dryer. The Washer has had problems since year one. We have just gone through service with Sears to fix a rusted out hinge on the lid. The tech broke the lid trying to drill out the rusted screws. He ordered a new lid and six weeks and one day later came to put the lid on. This was terrible. We were rescheduled two times for our appointment. Today the washer will not start on the cycle when you press the start button. We will never buy another Whirlpool product and not Maytag if what I read is true. Probably will be six more weeks to get this resolved.

This WP stove is so easy to use a child could do it. We use the built in timer all the time, not only when using the oven but timing items on the top of stove as well. Speaking of the oven, the self clean not only cleans but it leaves the oven sparkling. We love it.

Whirlpool Cabrio washer - Its been a month now and still the washer is not fixed. The repairman through Lowes warranty service is the worst by far I have ever dealt with. I had new transmission put on, still wont agitate and smells hot. The washer is only 18 months old, well taken care of. This expensive hunk of junk is worthless and the aggravation for all this mess is worse. I called Whirlpool 2 times. The first time, I got a call with the standard oh so sorry bit. Oh boy, that gets the washer fixed. Not. I blasted them and Lowes again. I have had it with this mess. The repairman is supposed to contact Lowes a week ago for replacement. He has done zero. I called Lowes to check. How can they sell this junk to customers who pay for this washer? They know it is junk, Lowes and Whirlpool, so do the right thing and recall the junker for refunds to consumers.

Whirlpool Cabrio Model Wtw8000BW - Purchased machine Jan. 2014. It does not wash my clothes clean. Clothes come out with dirty streaks all over them. The clothes I dry on a line smell dirty, like they werent rinsed properly. I have been cleaning the machine the first of every month per the instructions. I will never buy another HE washer again, this is my second one. Purchased a new one with an agitator.

Found after care service as bad as oven performance. Phoned for advice and told need to get used to new oven. My advice would be do not buy whirlpool ovens.

Spent the extra money to have a beautiful, slide-in oven. The AquaLift technology just seemed like another plus. After the turkey cooked, just seemed like another oven to clean. The AQUALIFT does not work, except for the bottom of the oven!! A fresh oven cleaner? Only available only. Get this beautiful range, not AQUALIFT TECHNOLOGY. CLEANING with it.

We purchased a Whirlpool Range from Brands Mart USA and did not try to use it for quite some time because our house was not ready to move in. When we tried to turn on the oven it would not come on. We called a repair service and was told the Motherboard was not working. We realize the warranty was out on the stove but it never worked and the stove is Brand New. We called Whirlpool and they was going to repair and changed their mind on December 18, 2014 at 8:54 am. Before that call we had spent quite a lot of hours on the phone with Whirlpool and Brands Mart USA.. We purchased three appliances from Brands Mart USA Range, Dishwasher and Microwave at the same time they were all Whirlpool products. What happened to Good Customer Service and Return Customers for Job Security? Well neither Company care for their customers. We did not break a motherboard for a stove oven because the range was never turned on because it was broken when purchased.. We are unable to get any help from either company. I talked today to ** & Supervisor ** from-Whirlpool and ** - Brands Mart USA, again no help. Why transfer you from one company to another for 1 hour and 45 minutes? WISH I COULD GET SOME HELP. And we wonder why companies go out of business - word of mouth complaints and especially with Senior Citizens like us.

Refrigerator model LFFU17F5HWD - For 2 years it worked, but with problems - always frosting over. I called a service tech and they said it was a common problem, but to find a service tech to come and look at it. The cost for that was $250.00 and still no fix. Now it quit working completely. I was always told by my dad that Whirlpool was the best - maybe true, 30 years ago. I know one thing if I have to buy another refrigerator - it wont be a Whirlpool. You do stand up to your name Whirlpool of trouble. If anyone reads this, please take my advice and do not buy a Whirlpool. I have a washer and dryer thats Whirlpool too. They work but I wont have anything in my house that says Whirlpool on it. Its too bad that they were a great product at one time. Consumer Reports should do something about this company or the BBB. Im so mad I cant even spell well. Thats my 2 cents on Whirlpool of crap.

I am sorry to have updated that review 2 years later. Whirlpool has actually contacted me after posting on their Facebook support group. I am not sure how it happened but I was contacted by their executive team who is WAY more professional and efficient than their support team. In a matter of days my washer was replaced and installed by a new one - the closet available to the model I had - I did not pay a penny and no questions asked even though the washer was out of warranty. So my answer to you is when you are stuck do your best to talk to the executive team!

Sounds crazy, but the outside of my stainless steel door is all dented. I live alone and one day noticed that it looks like someone body slammed my fridge. Is there air in the door panels that could be escaping or something like that? Anyone hear of this?

I paid over $1,000.00 for a washer based upon previous experience with Whirlpool appliances. I am single, over 65, and use this machine infrequently, as compared to when I had children. The only thing Whirlpool is offering is another of their machines at a discounted price. I value principles more than dollars. I refuse to give them another $600+ as a reward for making junk which apparently should have been recalled. The part I need is not available any place Ive found online. And it completely controls the power to the machine. You cannot open the door, you cannot turn it on. I had two service calls to discover this part is not available.

I am a fan of Whirlpool and I think the issues I have with this Duet machine is more because of the style but who knows. This is a front loader with lower water usage. It would have never gotten my sons sports uniforms clean. Never. The gasket around the front loading window frequently clogs so water doesnt drain. And perhaps worse, the drawer where detergent goes stays wet so it had gotten moldy and I didnt realize it. Now I remove the drawer after every wash so it can dry and I leave the loading door open as well. That just seems like a major design flaw and health issue.

Sixteen months after I bought the Cabrio washer (model # WTW7800XWO), the F1 error light came on. I had to replace the electronic panel on the machine for $400. Whirlpool refused to replace it even though they have been replacing this panel for others. This is a common problem with the Cabrio washer.

Model CAE2745FQ0, Serial #C72680766 - Purchased this coin op clothes washer 2/2/2018 at Brandsmart, Deerfield Beach FL. Would not empty or spin correctly; 1st service call 2/28/2018. (Less than 30 days from purchase date). 3/21/2018 called Whirlpool again as same problem continues (as listed above). Washer is not being overloaded. Whirlpool repair visit scheduled again for 3/23/2018. This is the 2nd repair time since we purchased the washer on 2/28/2018. Purchased the same model 2 years ago, and experienced repeated problems to the point where we got rid of that machine and purchased the most current model referenced here. We are looking for a full refund of the purchase price as it appears that this recently purchased machine is on its way to be a repeat performance of the 1st machine that we got rid of (that was purchased 2 years ago). Again, we want the full purchase price refunded, which is $900.88. This machine is not even 2 months old. Thank you.

I bought a fridge from this company not even 14 months ago. Went away for a week and came home to a fridge and freezer of rotten food. The fridge had died - Im guessing not long after I had gone away by the look and smell of the food and house. I have had nothing but the run around ever since that day. Spoke to this person and then that person. The electrician confirmed that my fridge is completely dead because of the compressor. So they sent a report to Whirlpool and they have now confirmed that I will get a new fridge. Now Im being told that will take 7-14 days. So I have been left with no food whatsoever as well as no fridge. I have two kids and cant even buy shopping for my son to take to school. And now Im being told that I had 9 months left on the warranty for the fridge that died and that’s all I will get on a new fridge. Should I not receive a new warranty for a new fridge? And should they replace my food? Could really do with some feedback on this matter. Please help me.

I have owned a Whirlpool Gold refrigerator since 2011. It has required two repair calls due to a water leak. The company did repair it free of charge on the second visit even though it was out of warranty. It is now leaking again which has caused damage to my wood floor and basement ceiling tiles. I am told that I have pay for the repairs this time even though it is the same problem. I was offered a modest discount to purchase a new refrigerator. I will never buy another Whirlpool product. This refrigerator should be recalled. I recommend GE products. They stand behind their products and they last a lot longer. Shame on Whirlpool! So many complaints with very little response .

It goes off balance, frequently. It is moldy and stinky. I wipe it out, use a cleaner and leave the door open, but it still stinks. I am getting rid of it and buying a Speed Queen top loader. I am extremely disappointed in the front loader Whirlpool.

I bought a whirlpool cabrio with high hopes. Unfortunately, it has been the worst washing machine I have ever had. Then I moved in with my fiance and he too had a cabrio. It too is a piece of junk - and brand new! Every load comes out with left over residue and the clothes look worse than before they went in! I have tried everything and I do mean everything! IM 41 y.o. - IM well aware of how to load a machine. I load it just the way the instructions say: as if there was an agitator there. Ive tried using no laundry detergent or fabric softener - clothes still come out disgusting. Ive made sure the screens are clean, doing extra small loads, turning on the extra rinse, everything! Ive called whirlpool, but there is no such thing as customer service anymore. They just blamed me for not loading the clothes properly and blew me off. The machine becomes unbalanced very easily (it is leveled on the floor), sometimes the clothes are still soaking wet at the end of the cycle and sometimes all knotted up. This is a horrible machine!! I wish I could say it makes me feel better that IM, by far, not the only one having issues with this piece of junk!

My new Washing machine was to be energy efficient. Yes, It uses less water to wash a load of clothes. Problem is, it takes twice as long to wash a load of clothes as older models. If it uses twice as much electricity, In what universe can this be considered energy efficient?

We have had our Whirlpool Cabrio washer for quite a few years. I agree that the machine is a piece of garbage. Every load is unbalanced. You have to stand there when the spin cycle starts, with your finger on the pause button, so you can rebalance the load, which is no easy task. My 80 minute whitest whites cycle took 2 1/2 hours to complete. Thank goodness I started the load at 5:30am. I hate this washer and anytime I am in an appliance store and see someone looking at it, I inform them it is a piece of junk. I havent contacted Whirlpool because I know they wont help with any issues were having.

I purchased a Whirlpool range YGY399LXUQ in 2012 from a great local appliance store, Trail Appliances. In 2013 the control panel stopped working and I contacted Trail. They quickly came out and replaced the control panel. In 2014 the same issue came up, but Trail could and would not do anything so I contacted Whirlpool Directly - they came out and replaced the control panel. In 2015 (same month) the control panel is not working AGAIN and Whirlpool has washed their hands of it. A replacement is over $400 + installation. The stove is barely worth that much. I would have thought that they would stand behind their product, in that this is an obvious continual issue or at the very least the service that they provide. I would not recommend their ranges to anyone because they will not stand behind what they product nor will I ever purchase anything that Whirlpool makes as it is obviously low quality.

Whirlpool Cabrio Washer model # WTW6800WW1. Bought it July 2009 and it broke Jan 2017... 7.5 years old. Cost to repair $715.00. The technician recommended that I just go ahead and buy a new one... not worth the while to fix. I paid $900 for this machine in 2009. This is an expensive machine, not a cheap ass one. Shame on Whirlpool for selling products that dont last and for making it unaffordable to fix.

My Whirlpool range, was purchased 14 years ago. It was fine until 2 months ago. I was preparing a meal for a dinner party and the oven went from low baking into Clean mode. (This cant be done by accident, it is many step process to go into clean mode) Locking the door! When I realized what was happening I immediately turned the breaker off but we still could not open the range door. Since the oven had my potato casserole and my Teflon coated cookie sheets inside it started to emit a toxic smell choking all of us inside the house. The unit was too hot to touch so my husband and brother-in-law finally donned gloves and got the range outside. I called Whirlpool the next morning and got the run around as to what type of range it was Kenmore/Whirlpool. Whirlpool finally sent someone out to look at the range and their determination was it caught on fire and melted! The company will not do anything about the unit or all the damage it cause because the range is over 10 years old. But they did not tell me this until I had spent weeks getting estimates and gathering information for them. I TOLD THEM DURING THE INITIAL CALL THE RANGE WAS 14 YEARS OLD. I TOLD THEM THE EXACT DATE IT WAS PURCHASED. Whirlpool sent me a letter from their Claims Resolution Department saying my DISHWASHER will not be covered and misspelling my last name. I have tried to call the person ** at least 25 times and she never answers the phone, only get her voicemail. I just wanted to tell them I was a little concerned about their accuracy with the typing of the name and product..... How complete could the investigation have been if they didnt even get the product correct.The smoke/smell ruined my microwave and ceiling fan. We had to paint the ceiling, redo wallpaper and professionally clean all the carpets and drapes on my first floor (we had just remodeled our kitchen last May so this was an expensive redo not in the budget. Not to mention the cost of a new range). I will NEVER buy a Whirlpool again. And I want to spread the word about the possibility of your range having the same problem.

Whirlpool serviceman came out to see why our brand new dishwasher didnt dry the dishes and left pools of water on glass bottoms. Repairman said all the new dishwashers are like this. The heating elements do not heat hot enough so that the machine gets a higher efficiency rating. He said the solution is to use the dishwasher during the day and at the end of the cycle, open the door so the dishes air dry. My previous 24 year old GE dishwasher did a great job of drying the dishes even when we didnt use the heated dry cycle! The only reason we had to buy a new dishwasher is because we bought a new house. I am very disgusted with the Whirlpool dishwasher. Might as well do dishes by hand.

The repair technician just left telling us that our Whirlpool Cabrio washing machine is fine. It is a little over a year old, makes LOUD noises as it runs, doesnt get the clothes clean and often doesnt even get them wet. The clothing sits above the water and comes out with pet hair, soap and dry spots. We use it the way the manual directs but it seems to be a totally defective machine. We sure wouldnt sell it to anyone nor give it away to some poor unsuspecting soul. Guess it needs to go to the dump. Shame on you Whirlpool for taking advantage of so many of us.

Washer does not clean clothes period. Darks come out covered with white soap residue and smell dirty regardless of how little soap is used or with using extra rinse, which takes 84 minutes by the way. Whites only seem slightly cleaner since hot water is used and you cant see the soap residue. If you wash more than 5 or 5 items at a time some do not even get completely wet. Just waiting for it to break down next according to the other reviews. I spent a lot of money to get a nice washer and dryer and ended up with junk. Id rather have an old 1970 washer, probably designed better and most likely would clean better.

Bought set 12/5/14 at Lowes Tucson. First load came out with shirts looking like theyd been scrubbed with sandpaper. Called Whirlpool & was advised to use higher water level for loads. Then noticed small hole in my favorite shirt. Oh well. Next I found an area in my king sized bottom sheet with several holes and torn fibers. Thought maybe it might be from my toenails, except it wasnt where my feet would be. Finally a pair of capris (just worn twice) found with same type of holes and torn fibers. Dryer also inefficient. Balls up clothes - outside dry; inside wet. Re-run one or two inside wet pieces and they dont dry at all! What kind of technology is this?

We purchased a Whirlpool fridge from Future Shop four years ago. It was delivered by professional movers and we plugged it in and smoke filled the house. We called Future Shop and very soon, another fridge arrived on the back of a pickup truck (no box or papers, etc.). This fridge is slowly ruining our kitchen floor as from time to time, we notice a puddle of water leaking from under the fridge. We called the store a few times but were told its normal for a fridge to do that in hot weather.

Having multiple apartments I have some experience with water heaters, with that being said, old school water heaters would last 30 years with basically no maintenance. Since those old, manual no BS flashing light codes were replaced with Whirlpool brand, I see constant problems. Honeywell valve/motherboards was the worst thing that could have been put on any equipment. More or less they all failed within few months past warranty expiration date. Replacement part is cost almost half of what brand new product costs. When called customer service, they are aware of said problem but will not help, or recall above product. There are plenty of videos and forums of people complaining about the same issue. Being poorly treated by customer service, I know that I will no longer be spending my money on whirlpool brand. 3 years off of the water heater is a joke.

Bought fridge in 2010, I am about to replace the icemaker for the 2nd time at a cost of over $300 each time by a Whirlpool authorized repair tech. No kids in the house and very limited use of icemaker. Motor keeps burning out because of the design flaw per the tech. Very poor design for a $1,500 fridge. Due to these issues I do not intend on purchasing Whirlpool products in the future.

The Whirlpool side-by-side had the space and durability we had hoped for in the price range we shopped in. It lasted longer than the refrigerator it replaced.

Ill never buy Whirlpool appliances again. I purchased all new kitchen appliances less than 3 years ago. The range had electrical issues within the first year, which was extremely scary. Thankfully because of the warranty they took it back, reimbursed me for it and I replaced it with a GE. I absolutely love the GE. The dish in the microwave never stays on its track in the center. Its quite an inconvenience to fix it almost daily. The top rack in the dishwasher constantly breaks, drops down on one side. Random parts from inside the dishwasher constantly come loose and fall off. But the worst of all....my refrigerator has broken down twice in 6 months from the same issue due to no fault of my own. To give some credit, Whirlpool fixed it out of warranty the first time. However the same issue happened 6 months later and they are expecting me to pay for it. The repair company contracted with Whirlpool covers their parts under warranty, however different parts need to be ordered. I had to pay for these parts, a service call and labor. Whirlpool came out with a service pointer on this because they know its a manufacturing defect but are refusing to cover the cost. The representative I spoke to was nasty and inconsiderate but sadly the manager was even worse. DONT buy Whirlpool!!! I recommend GE, youll be much happier. Worst customer service and support.

We purchased a Whirlpool refrigerator on October 18, ‘11 in Viveks at Tambaram. Next day itself, 19th of October, 11, the door lock of the fridge is not working and the defrost light is also not working. Immediately we logged a complaint in Whirlpool customer care, which is in Chennai (mothers care). The engineer came and he removed the lock and he said, “Its a new model lock, we dont have any spare. We will raise an incident to Whirlpool and will replace with a week.” But almost one month over, today is the 21st of November, ‘11. We called the customer care office more than 10 times in this period, but we are not getting any response from them. Today, I spoke to one of the executive in the customer care Mr. R. and asked about the status. But he said we dont have that lock and he asked me the copy of the purchased bill of the refrigerator for replacing the unit. Really, its very poor customer service and I’m very much disappointed with Whirlpools product. We used Kelvinator for more than 11 years and we never had any problem. But with this Whirlpool product, within 2 days we faced these problems. Cooling coming out through the lock hole in the door of the refrigerator. Electricity consumption is more. No defrost happens automatically so far. Almost, it seems that the refrigerator may go down to critical condition. Request your intervention to resolve the issue as soon as possible.

These machines are designed to clean your clothes by rubbing them together which they attempt to do in a minute amount of water. They destroy the fabric, pull the seam out of shape, wrinkle them beyond the point of wearable, do not get them clean and do not get all the detergent out. I have had clothes come out partially dry. They also do not dilute the fabric softener, leaving unremovable stains on your clothes. In addition, they take forever to do a load of clothes even without the extra rinse you need if you want any hope of getting the clothes rinsed. The dryer is the slowest dryer I have ever had. The steam refresh that is supposed to get the hideous wrinkles out of your clothes does not put steam into the dryer. Instead, it sets the dryer to the highest heat so that those clothes you did not want on high heat are now getting it; then it shoots bursts, yes large bursts, of water on them. Your clothes come out a combination of still wrinkles and wet. If you hear of a class action suit, please contact me. These machines should be recalled.

After 2 years the motherboard failed on my Top load Cabrio washer. We had to spend $300.00 dollars to get fixed. When we called Whirlpool to see what they would do about it, they actually offered to sell us the board for $345.00 dollars and a 1 year warranty on the board. They actually wanted us to pay more from them than a local repair service. DO NOT BUY THIS MACHINE OR ANY OTHER WHIRLPOOL PRODUCTS. Also does anyone know of any class action lawsuits surrounding their obvious use of defective parts?

I have purchased 2 Ikea/Whirlpool ovens in 2011 from Ikea in Canada. I have used the self clean feature on both ovens and both ovens quit completely and the doors stayed locked. This problem is discussed hundreds of times on the internet for Whirlpool, Ikea and Kitchen Aid ovens. Since they are all made by Whirlpool they are all very similar or exactly the same in some cases, as is the problem. I have discussed this with Ikea and they have said they didnt know about the problem but would help to get it fixed to my satisfaction. I have had Whirlpool authorized service repair both ovens but after trying the self clean feature again, same problem.During one of my conversations with an Ikea representative on the phone, she contacted Whirlpool and was told that if the oven was repaired 3 times and deemed by the service technician as unrepairable, Whirlpool would do a buyback. In other words according to Ikea, Whirlpool would take the oven and pay me what I paid for the oven. Well after contacting the authorized service dept (not Whirlpool itself) for the third time, they did some investigation with Whirlpool about the problem. To his and my amazement, Whirlpool has come up with a fix as of October 2013. The technician ordered the new kit and installed it in both ovens. I have since tried the self clean in one oven and this time it worked. For the information of others, Whirlpool has the kit and in it is an instruction sheet with pictures as to how to replace and install all the parts in the kit.I watched the installation, quite a process. From the instruction sheet there is a number on it. Here is the number - w10625529 rev. A 10/13. This is an instruction sheet for Ikea TOD (thermal overload device) service kit. I have looked at many of the service parts diagrams on the internet for many different current models of Ikea, Whirlpool and Kitchen Aid ovens and in most cases almost all the inside parts are the same or very very similar which leads me to the conclusion that this service kit may work in most of these ovens to correct the same problem, but I suggest checking with the appropriate service people before taking my word for it. My observation is that the kit moves the TOD off the top of the metal plate of the oven and onto a new bracket which the tech thought it was to get it further away from heat (this Im not sure of since Im not an expert). He also suggested that this kit may also be designed to allow more air flow around the oven.My only concern after having the self clean feature finally work is the heat produced inside the kitchen cabinet in which the oven is installed. Approximately an hour and a half after turning the self clean on, I felt the side of the cabinet between it and the fridge (open space), and at one area of the wood cabinet I could not hold my hand on the cabinet as it was too very hot. I will be checking the inside of the cabinet for signs of excess heat and if I see any evidence, I will again call the service people. Since the elements were not on when I checked this, I assume the self clean had finished the heat cycle and was in the process of cooling down. When I test the other oven, I will make sure the elements are still on as I can see them thru the glass door. When I checked the temperature of the outside wood cabinet using a laser thermometer, the outside wood registered 64 degrees C or 142 F approximately. Not sure what the inside temperature was as the oven was still in place. Hopefully I will not get a higher reading when the self clean is at its maximum temperature in the cleaning cycle. Will the oven create any problems in the future for the cabinet, I hope not but time will tell. For clarification, the cabinets were built by a kitchen cabinet company using the instruction sheet that came with the ovens. I hope some of this will be of help to some of the hundreds of people who have posted this very same problem on the internet. When you have paid for an appliance you wanted because of the features it came with, it should provide you with what you paid for and not constantly break down. Im lucky as they came with a 5-year warranty so it hasnt cost me anything yet and hopefully wont in the future. Good luck to all in getting this resolved for all of you.

Whirlpool Dryers: I have 2 Duet Dryers and the user interface has gone bad with both several times. I called whirlpool several times to repair. The last time, they refused to repair the dryer. I started having problems with my dryers within the first 6 months of owning them. The repair guy that they sent out the first time said this repair was a major problem with the duets but the company chooses to not acknowledge the problem. They should be required to have a recall. Never by this dryer, you will regret it!

I just bought a house with a Whirlpool Accubake wall oven and after I did a self-clean, the oven quit working. It goes through the motions of working but neither element heats up. After replacing the elements ($95), I am going to replace the thermal fuse to see if that cures the problem. Whirlpools automated Customer Service phone service sucks. You cant talk to anyone about troubleshooting any problems so you spend money until you eliminate all possibilities.

We purchased commercial washing machines for our building, we discovered that the clothes were coming out of the machines with dry spots and partials of soap. When we asked the dealer about this they sent a tech. to check the machines. It seems that these machines do not allow a adequate amount of water into the tub to wash the clothes. Only 6 or 7 inches of water is not enough water to wash a full load. When asked how this can be fixed I was told it cant be fixed. I was told this is a energy saving machine, which means you can only wash very small loads!What is the point of running a machine for twice the amount of time to do what you used to do in one load? Had we known this before purchasing what we felt was a quality machine, we are now stuck with machine not capable of doing what is required of them. When asked if they would take the machine back, no is all they say. I would never buy any product made by Whirlpool or Maytag because of the way this problem of ours has been handled. We purchased these machines from Prestige appliance, they have been good, but with no support from Whirlpool.

Not cooling properly on wpf560smywc2 French door - Milk only last 3 days. Temp wont stay consistent. 4 times out and say normal. Ice is forming on fan in freezer and back wall causing no flow in refrigerator but freezer cooling. Only 3 months old. Lowes Service Advantage (Extended Warranty) nor Whirlpool will replace or do anything about it. Was told 3 times out and replacement then today they sent me email with their policy or 3 times out with a repair (Parts must be changed) wait 30 days then another repair etc. then on 4th repair will replace. Lied to buy sales and called liar by repair guy when he told Whirlpool nothing wrong. I just wanted a new one cause I didnt like features. Lowes has a return policy which has in fine print only 30 days for refrigerator so they wont help. Was told I have to do a food loss claim and they would email form. Still hasnt happen. Lied to and get a replacement or repair and cant afford another.

I have a new Whirlpool double convection oven which is very noisy. There is a rattle and pinging noise that occurs and the fan is also loud. Im not sure if it is an install or product issue. Can anyone comment on their convection oven? I dont believe this is normal. I am disappointed with my purchase and would opt for gas or basic electric. The double convection ovens were fairly pricey too.

Exterior metal reaches temperatures that cause minor burns on an adult finger and could be potentially more dangerous for a child. The self-clean feature has crashed the oven on two out of three uses of this function and overheats handle.

The washer works well for the age of it. However, I would say it is not designed as nicely as some of the others I have seen. I found it performed okay doing the wash, but it didnt hold up as well I as I would have liked. Seems cheaply made. The machines plastic parts have stained from rust and seem tinny.

In 2007 and 2008, I purchased 7 natural gas heaters: 1 for my home and 6 for rental properties. I have had nothing but problems from all of them. Two of them failed this weekend (one 40-gallon and one 50-gallon). I called the 800 number and have to pay $63.50 for parts for the 40-gallon and was given a PO number to pick up parts for the 50-gallon at Lowes. They do not have the parts. I have spent over $250,000 at Lowes since 2000. I have all Whirlpool appliances in rentals and my own home. The discussion I had at two Lowes stores today really showed me how they take care of their customers. I told both stores that I will never buy the Whirlpool brand again!

Only problem is you have to open door to access functions. 30 second increments and stop are on outside. Beautiful to look at and inside is easy to clean. 4 fan levels, vent inside or outside. 2 light settings. Nice and bright. Low profile over stove but big enough to hold large casseroles.

I purchased a Whirlpool induction cooktop Aqualift self cleaning oven Nov.1/12. The oven has never been easy to clean you always have to scrub it, now I boiled some pies over in Oct/13, the syrup burned into the bottom of the oven before the pies were finished baking. My oven is now pitted, warped, and bakes very unevenly, have contacted the merchant, Saskatoon Appliance, Whirlpool, and Excelsior Insurance (extra warranty) Insurance guarantees 24-48 hr service but to no avail. We still have no service 1 month later.

Uses little soap. Not sure on clean. Don’t think front loader clean as well as top loaders. Would recommend top loaders with no agitation. Also would recommend white as a standard color. I am unhappy with the way a front loader works. I am happier with a top loader, cleans better.

My refrigerator will be 3 years old in September. It stopped working two months after my warranty ended, in November Thanksgiving Day. I was so thankful that I had snow on my deck to keep everything cold. I had several family members in my house and watching my husband defrost a frost-free frig? This was a nightmare. Then a few weeks later, my husband company refrigerators did the same thing: freeze up and stop working. He defrosted theirs as well.I know that lots of consumers have had the same issue with any of the bottom freezer refrigerator doing the same thing. I think we, consumers, should make these company recall these lemons. Why should we have to pay more and buy more our parents had their appliances last for years. He had done this approximately 3 times since my warranty ended in September of last year. The problem is the food goes bad, the freezer ices up, causing the refrigerator to ice up and stop the air flow.I contacted the company and this is what they told me: I had to pay $295.12 to get the repair completed. It was the DEF control board. I guess others have the compressor go out and that cost over $600 to fix. Why is it our fault as a consumer buying their products promised and concern for 1 year, not 10 years. It is no wonder why America is broke? My question to the Whirlpool was, how on earth can this be the consumers fault? Here is their reply:According to the model and serial number provided, we do not indicate that there are any known recalls with this particular model. A recall requires that a product poses a threat to a persons life or health. Since this is not the case in this instance, we do not have a recall. Once a product warranty has expired, any costs for maintenance, service, or component replacements are then within the owners time frame of responsibility. Taking this into consideration, I regret to inform you that due to the age of the product, we will be unable to assist with the cost of the repair. If you have purchased an extended warranty, we would recommend contacting your extended warranty provider directly to discuss the options they provide.Oh, they sent me a postcard asking if the repair service I received was good... Yes, the company who came out did a fantastic job. I think I may have to call them back; it is acting up again. I have 90 day warranty....

It was a complete nightmare buying our all side by side stainless steel freezer and refrigerator. Freezer still working fine but the refrigerator started blowing hot air, all the food spoiled within 2 days as we were trying to figure out what was wrong. The store did the best to correct the problem and it seemed the Whirlpool company had no faith in their product as over the phone recommended having extended warranty. So sorry we bought this product, nothing but hassle!!!

Whirlpool French Door 32 Cu. Refrigerator - Purchased refrigerator Nov 2016. Never worked, never cooled. Called Sears and was told to call Whirpool. Had to then wait 1 week for repair company to send out service tech. He determined it was unrepairable. A replacement was delivered. The replacement started flooding the interior down the back, filling underneath the bottom drawer and down into the freezer (ruining everything in the freezer) and out onto the floor. Called Whirlpool and had to wait another week for a tech. They assessed the problem and left. I was told it would be fixed within the week, that theyd call when the parts arrived. 3 weeks later, no word. Called Whirlpool, the parts were on backorder with no ETA. Two weeks later the parts were expedited, after I called again crying, and a tech came out again to fix the flooding. Two weeks ago the fan started to make a very loud noise and the internal temperature started to fluctuate and finally settled between 55-60+. Everything was ruined, again. This refrigerator is defective. Whirlpools customer service is deplorable. DO NOT BUY ANYTHING FROM WHIRLPOOL!!! They dont care that they make and sell defective crap. They dont care about how much money and time youve lost because of their defective merchandise. You have to have a service repair person come out at least 3 times before theyll even consider a replacement unless the repair tech considers it unrepairable even if it never really works or if the parts take weeks to be delivered. They DONT CARE about anything. Worst part is that I have no power or recourse. No one will help me. I was told today by the Sears Customer Relations to hire a lawyer. :( This is so wrong.

I purchased my Whirlpool refrigerator in March of 2011 and the ice dispenser failed in early April of 2012. I called Whirlpool and asked for a repair, but they refused, saying the refrigerator was out of warranty. Being a handy person and upset about the failure after only just over a year, I took the dispenser apart and found that a plastic part had broken and caused the ice door to become unhinged. I called Whirlpool back and explained what had happened, but they refused to help again. They transferred me to the parts department where I was told that the part that was broken was not available and the only thing I could do was replace the entire door! Not only is their product poorly designed, but it is also not easily repaired. I will never buy another Whirlpool appliance.

I bought a Whirlpool refrigerator because it was the lowest priced model that offered a bottom freezer compartment and fit into our available space in the kitchen. We also want a white coloured appliance. One thing we never noticed until set up at home was that there were no ice making trays nor an ice bin. We have had the fridge for five years with no problems. It is quite noisy when running.

The latch on the attached-to-the-door silverware basket on our Whirlpool GU3600XTVQ3 dishwasher has broken three times since the unit was installed in July 2011. This last time, the technician brought a new one and it broke the next day. I cannot understand why a company with a supposedly good reputation would include an accessory with such a faulty design, made of such flimsy materials. We have the basket wired shut again and have to call the repair place, but I have no confidence that anything the technician brings to us will work any better, since its the same stupid design and shoddy workmanship.

12 months and 2 weeks, my ice maker quit working. I called Lowes where I purchased this top of the line junk. The first thing they asked was do I purchase the extended warranty. I said no. He advised to call a repairman he recommended, but I would have to pay for the repairs. Whirlpool was just as bad; no warranty, you pay. It appears they are both relying on warranties rather than selling dependable products or customer satisfaction. A couple months later, ice forming on the bottom of the freezer, and puddles every couple of days in front of the refrigerator. I pulled the two draws out and removed the ice. Within a week, it was back. A $2400 refrigerator should last longer then a 1 1/2 years without falling apart. My Whirlpool dishwashers only lasted 1 1/2 years also.

I purchased a washing machine in year 2002. It was working perfectly. Recently, its drive belt started slipping. I called local service center, S. R. Enterprises, with mobile number 9204792391.The technician came after 3 days and declared that the gear box is leaking and will have to be replaced. They had no gearbox in stock for model f45, top loading, fully automatic.After a wait, they took away the machine to their workshop on 30.09.2011 and returned it on 04.10.2011.They charged me Rs. 4,730. I will have to be replaced. I found that its LID, which was perfectly okay, is now making a terrible sound when opened and would fall down, not allowing to load the machine. I informed the service center immediately. After many reminders, a man turned up yesterday and declared that the LID will have to be replaced and I will have to pay Rs. 2,000 for that. I rang up the service center to say, Since it has been damaged in your workshop, you should replace it free of cost to me. Their reply was evasive and negative. I called your call center and they registered my complaint - customer number **, comp. number **. I was assured that the LID will be replaced within 24 hours.

Purchased 11-02-2016. This Whirlpool/Kenmore dishwasher is falling apart. Top rack wheels are totally broken, ordered parts 4 times, gave up. Now they are held together by gorilla glue. I have gone through 3 gray plastic end caps for the top rack runners. Now one is contained by a plastic slip tie. Last week it started leaking. Sears was totally useless. Whirlpool keeps sending me back to them. Now, I have to go buy another new dishwasher. It will not be a Whirlpool. Next time getting the extended warranty.

I purchased a Whirlpool refrigerator less than a year ago and both the door and icemaker have a problem in which PC Richards, the store I purchased it from, has had to service the refrigerator at least 3 times and have not resolved the problem. The door does not close properly and every time I use the icemaker, condensation builds up. Each time a tech person comes to my home, a different reason is given. I need this problem resolved. I dont need to monitor the refrigerator like a sick patient.

We purchased Whirlpool Cabrio Washer WTW5600 series in October of 2010. I bought the machine from Sears and also bought the extended warranty. Less than 6 months after I had been using it, I noticed that all my husband’s shirts were getting sweat stains under the arms and my hand towels were very smelly after drying with them one time. I called Sears to have someone come out and tell us what the problem was. He said I was using too much detergent so I reduced the amount of what I was using. It did not help the problem so I started using the extra rinse each time I washed, still did not fix the problem. I called them out 3 more times in 2011. One tech told me I was still using too much detergent so I reduced down to 1 tablespoon like he suggested. I stopped using softener in my washer because he said I needed to clean my machine more than one time a month, to clean it every 3 weeks. No solution to the problem still. I have had a tech from Sears and one from Whirlpool (who incidentally was the same man, he was from A&E Appliances). When he came in the door, my husband told him he had been here before and I said 2 times. He lied and said he had not been out before. Are we blind? No. He ran the cycle but sat in his truck while he was running it. None of the techs have ever put a tool on the machine to check if the water level is right. They just stand there and tell us to change the amount of detergent or clean the machine with Clorox more often. I cleaned it 8 days in a row and the clothes still smell and still do not get cleaned. We talked to main man at Whirlpool and said they couldnt do anything because their 1 year warranty had run out. We have been using Whirlpool appliances for over 30 years but I will not ever buy another one. I have probably had 5 Whirlpool washers over the years but never had a problem until we got this Cabrio top loader without an agitator. I would not recommend this washer to my worst enemy, if I had one.

The Whirlpool water heater I bought 2 years ago at Lowes has had continued problems with its thermocouple causing the water heater to shut down. At first I would have to relight it about every 2 weeks, now I had to do this everyday. I was going to replace the thermocouple until I read numerous sites explaining that several people did this and experienced the same problems.

Whirlpool has been around for years. This is my 3rd machine. I had both washer and dryer. But machines today arent made like they use to. They breaks down easily. The parts are cheap. I had a Samsung washer. It was one of the recalls. I got ripped off by Samsung and Best buy. I have received the full value.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.