The W/D combo-Cabrio is crap... Dont buy it. Salesperson @ Lowes told us all washers moving away from the agitator to ones like this so we bought it. The washers does not clean everything - does not use enough water to clean - leaves your delicates so wrinkled and clothes in general beat up. The dryer decides when it thinks your clothes are dry when they are actually still very wet... very noisy. Whirlpool must have sold out because quality integrity sure is gone.

We purchased a number of Whirlpool appliances (dishwasher, double door refrigerator, Duet stackable washer and dryer). After 14 months, the ice maker broke. $200 later, it was repaired with an upgraded kit.Last week, the washer error coded and the door locked so we could not get out the wet clothes. Called customer (no) service and they advised that we needed to call a service tech because he has a special tool to unlock the door. I stopped by our local appliance store and the counter person told me how to open the door. Had the tech come out for $70 and it could be the lock mechanism or the control panel. It turns out to be the control panel, which costs $250 + labor and would total to around $500, give or take a little. We are in our 60s, my wife does not take in laundry and the ice dispenser was seldom used because I can sneeze ice faster than this can dispense it so I open the freezer door to get my ice.The tech and the store clerk said that these were common problems with these machines. This was a major expense when purchased. So far, the dish washer has not had any problems, but tonight might be the night. The reason we bought Whirlpool is because of the Maytag connection, now that is in the same toilet.

Problem of refrigerator is working good for a few days, then the freezer is all melted down for a few days, then back to working good again. Model: FD2560HES. Serviced on and by: 7/16/2015 - ** - told me the controller board is bad, need to order part. 7/23/2015 - ** - replaced the controller board. Resulting same problem. NOTE, which means my old controller board is as good as the new one. 7/30/2015 - ** - opened the freezer, back of refrigerator, told me the compressor is no good, gave me an estimate of total cost $817.86. I did not accept the proposal, and I did not agree the compressor is no good. I called and scheduled for service after and scheduled to have service on 8/4/2015. Then got called from the office, said, Cant come on 8/4/2015 and told me I have to pay the $95.00 first visit. So I called and spoke to the manager, then scheduled for next service.8/13/2015 - ** - when he came, the refrigerator is working fine. He said, Cant diagnosis the refrigerator, told me to call for service when it is not working. He said the compressor is good. 8/15/2015, early morning the freezer is all melted. I called, been told cant service the same day. 8/17/2015 I called the office (1-888-717-9322), requested to talk to the manager, promised to call me back. By this date 8/28/2015, still no call back from the manager. They are located in Michigan. I was told the local office address is: 9582 Katella Ave., Anaheim, CA 92804.

Purchased a double wall oven and had it for 13 months. Used it this past Christmas and for the first time used the self cleaning mode. After an hour the power went out and now the oven is dead. Whirlpool service sent me to a local repair company and they want $70 to come out and look at the oven. This seems like a huge problem based on all of the feedback on the web. This is an obvious lemon and Im going to talk all over social media about the poor quality of this product.

Water heater purchased in 2011 and is already broken. Called the hotline and they were rude. Told me I need a $199 part. I read all the reviews and it seems that Whirlpool has made a bad name for themselves with the water heaters. They were not willing to work with me.

My wife and I spent about $2500 on a new Whirlpool Dutch Door fridge five years ago. 18 months later the evaporator went out and the warranty was only good for one year! We bought an extended warranty, got it fixed and the other evaporator went out less than a year later after that! Next, the circuit board control on the crisper went out. Then, the water filter would not disengage and a repairman had to take the fridge apart just to put in a new filter! And now, the ice-maker has gone out and the fan is icing up like another evaporator is going... Insane! Our warranty is up next year. Once the warranty ends we will start shopping for another unit - and it wont be a Whirlpool - thats for sure. I have never owned anything this unreliable in my entire life! Also, I would say most of the time we have owned this piece of you-know-what it has made a loud disturbing fan noise... What a waste of good money! Run! Run far, far away!!!

I purchased a very expensive Cabrio top-loading washer thinking I would never have to worry because supposedly it’s the top of the line, right? Well, I have it a few years; the first week they replaced the basket because it was ruining my clothes. And then I had to replace the pump because of a coin getting caught and putting a hole in the pump. Really? What the heck? Now the basket is all shredded at the top. Obviously that isn’t right, so what do I do now? Replace the basket again? Who gives them the right to charge so much for a piece of junk? Plus, it’s supposed to save on water, but I feel that the clothes don’t really clean well. They hardly feel wet coming out of the machine.

I bought a Whirlpool Cabrio washer on 11/07/10. I brought it home, hooked it up, turned it on and water came pouring out the bottom. I should have known better then, but I took it back and got another one, same model. I dont even have it 2 years and its locked up. I had a repairman here and was told it needed a new water pump ($200 plus). There are 3 adults in my home so its not like I use it hard. I am really disgusted. This is the 3rd washer I bought from Whirlpool in less than 10 years. I went on the Whirlpool site and voiced my disappointment and my problems with their washers. I was told they take pride in their products and I should have a nice day. Yeah, right, they dont have to drag clothes up and down the stairs and then to a laundromat when theyre in their 50s with a bad knee and back. Yes, I will have a nice day when I get that piece of junk out of my house. I will never buy anything made by Whirlpool again.

Ive bought a new home and I purchased a brand new Whirlpool black oven range. First, a piece of metallic on top of the oven broke. I couldnt believe it. And the biggest problem is that whatever I do to clean the top surface, it always leaves a stain. After a few months, the oven looked like 10 years old piece. I called whirlpool and talked to a customer service rep, he told me that I needed to clean the surface immediately after something spill on it. To make sure if I understood it right, I asked him You mean when I am cooking some rice and some water spill out, do I have to remove the pot and clean the surface and repeat that all along while I am cooking? BELIEVE OR NOT, THE ANSWER WAS yes. I cant believe the bad quality of this product and worst, its customer service defensive attitude. Dont buy this product.

The Whirlpool repairman left today after replacing the burned out motor on my 5 yr old dishwasher bought in Feb 2012 and installed July 2012 as did not arrive from Quebec to Surrey BC until the end of June 2012. So the Finish dishwasher detergent was in the dishwasher as samples and coupons and recommended this Finish for use in the new dishwasher so I stupidly believed them and used it. Well last week my dishwasher stopped working after it started and turns out today the cause was from the Finish dishwasher detergent. I was told today after paying 393 dollars for the repairs. Not to use Finish anymore or I will have the same problem. To only use Cascade. So what is a person suppose to believe.

Brand new Whirlpool dishwasher letting steam out ruining cabinets. Whirlpool admitted this has happened before. ** sent 3 different service repair companies to my house and all 3 told me the parts they recommended from Whirlpool was not going to fix problem. They finally after 3 different repairmen agreed to refund dishwasher. I requested they hire someone to give estimate on my kitchen cabinets. It was their product that done damage and I live in rural area and no one wants the job of restaining. If the cabinet is replaced it is expensive. Granite counters have to be removed and placed back, sink etc. I requested 3000.00 or Whirlpool send someone to give estimate. This has been dragging on for 2 months and still cant use dishwasher. Is that too much to ask for? This has been a nightmare and Whirlpool should be embarrassed. So many emails and messages and most of the time they are unreturned

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

Model # WFG510S0AS1 SER #R30850040. Oven was installed NEW in the home I purchased in July of 2013. I used the cleaning feature on it in Nov 2014. I am amazed that it did not start a fire. Please see pictures attached. The whole control panel melted. This makes the oven unusable and extremely dangerous. I will need to replace the whole control panel. I followed the instructions completely in the manual provided for the cleaning cycle. It says in the manual to only clean the over this way as using easy off or any other cleaner will damage the inner surfaces.Whirlpool claims they have no knowledge of this problem but there are numerous complaints on their site about it as well as other internet sites complaining about the melting of the control panel. I need to know how to fix this problem and dont believe I should have to pay for something that is obviously a flaw in the materials used. It is extremely dangerous. Since these pieces of Whirlpool equipment were installed by the broker that originally purchased the home, I have no record of purchase. I can try and contact him and see if he has anything but kind of doubt he has receipts now.

About three months ago the freezer iced up. Tech showed up stating that the motherboard went out, needs to be replaced, had to wait 6 days for part to show. Was replaced. Two weeks later freezer iced up and refrigerator got hot, lost a lot of food. Again motherboard went out again, had to wait another six days. Part came in Tech replaced the motherboard and installed a heater defroster. Worked for 2 weeks and now the freezer is icing up again. What a pain in the ass.

We purchased 2 Whirlpool Cabrio washing machines in 2011. Both required service calls in June 2015. After 3.5 years, the repair company diagnosed that the Whirlpool Cabrio model number WTW7800XW2 bearing needed to be replaced for an estimated $650.00 and recommended that we purchase a new machine. The other machine was spewing water out of the side of the machine. The repair person took the machine apart and could not duplicate the problem.

I purchased a new Whirlpool washer and dryer (model number WED9250WR0 #WFW9250WR00). The washer broke after about 2 months. They took my washer and gave me some off brand one, because I purchased a 5 year extended warranty. They kept my washer for over 3 months, saying that the manufacturer takes that long to get the parts in. Its ridiculous! The tub, seal, and some other parts had to be replaced. It was shredding my clothing and my bedding. The first time they fixed it, a couple days later, it started making a horrible noise. The repairman came out, and a part had fallen off inside, so he put it back on. It kept happening, so I called them back, and he taped the part on!About 2 months later, the seal started shredding, and so did my clothing. I called again, and they had to replace the seal again. It still sounds off balance, and they said that was normal, because of the give in the floor. The day they fixed the seal, I washed a childs sleeping bag, and it shredded it too! I called again, and they refused to replace it, and they want to come and look at it again. My dryer lint trap seal also keeps coming apart, and I have gone through 3 of those in less than 8 months. They said they are just made poorly, so it will keep happening. I just want my money back, and buy a different washer and dryer somewhere else. I had an old pair that I bought, used, and they lasted me 5 years with less problems than these that I paid two grand for.

I purchased a new Whirlpool Cabrio washer/dryer set 2 1/2 years ago (Jan. 2009). I have 4 kids and do lots of laundry. This is THE WORST appliance, namely washer, I have ever owned! I so wish I had researched this product more. I ditto everything that has been said about this washer. It tore up so many items of clothing, I lost count and does a horrible job of getting stains out. I contacted Whirlpool on several occasions only to be told that they would send a technician out to see if there was something wrong. The technician would report that the washer was working properly and Whirlpool would then tell me, sorry, we cant do anything about it. I asked them if a washer was supposed to clean your clothes and unravel them? Yes, it is supposed to clean them. Well, its not doing that. No, it is not supposed to unravel and destroy them but well, it IS doing that! Therefore, the washer is not working properly. Just because a technician can not physically find something wrong with it, doesnt mean it is a poor functioning washer. This company should better learn very soon that you must stand behind the QUALITY of your products or you will soon be out of business. I will never purchase Whirlpool products ever again nor would I recommend it to anyone!

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

I purchased this Whirlpool Cabrio washer three months ago from hhgregg. If I hit the lottery, the first thing Im going to do is take it to the dump and buy a new washer. There is no way to wash a load of towels in this machine. I started a load at 7:35 this morning and it is now 9:53 and Im still dealing with the drain and spin cycles. Over and over, I try to get it to spin out enough water that I can put the towels in the dryer. I should have suspected something when I saw that the washer even had a separate drain and spin cycle. It should have told me something. Its a piece of junk. Never again. Im back to Kenmore.

I purchased a new Whirlpool stainless steel smooth top range model #WEE745H0FS and it was installed the day before Thanksgiving, 11/22/17. The oven door handle was broken on inside by installers. I called Whirlpool warranty on 11/24/17 and requested a repair. A repairman came the following week two days late. He said he needed to order a part. After calling the “Whirlpool approved” repair shop multiple times over the next two weeks, I was told the part was backordered. Finally, yesterday, 12/13/17 the repairman showed up an hour later than appt. time. He took the oven door apart again and the new part didn’t fit my oven door. He had carelessly ordered the wrong part. I was told he’d put a rush on the correct part and that it would be here 12/18/17. I will never buy another appliance from Kelley Appliance in Augusta GA nor another Whirlpool product. I have had to use duct tape on my brand NEW oven just to use the oven so it doesn’t fall apart when opening.

We purchased our 4 French door refrigerator in November 2014. It started making a loud noise, like an air compressor about a month ago. So loud that when we are watching TV in the bedroom we have to close the door! It continued to get louder and more frequent so I called Sears. It is under warranty so they sent a repairman out. When he came, he said it was because we had the refrigerator too cold & it was causing ice to be stuck around the fan??? We had it at 5 and the coldest is 7... He suggested we put it on 3. 2 days later and it is making the same noise again. Will be calling Sears again. I saw a similar review saying the same thing!!!! This is a five month old refrigerator! Very disappointed in product and service.

This washer is a piece of junk!! It doesnt use enough water to clean the clothes and now it wont spin them dry. I have maybe two loads a week on a regular basis. I have always used HE detergent. Never overload. It is only three years old and I have been having to go to the laundromat because I cant afford a service call and especially if it is what they say which costs almost much as the washer. Be ahead to buy a used washer or a cheap one. It wasnt getting the clothes spun out dry enough - dripping wet. Then it flashed od and ul and sd and f51 and then it kidnapped my clothes - couldnt get the door to unlock with the pause or power until I unplugged and still had to wait several minutes. They refuse to help. Do not buy this machine!!! The customer service was not one bit of help. Instead she wanted to charge me $350.00+ dollars for some plan.

About two months ago the washer starting stopping and the UL light continued to come on during every spin cycle. So I would adjust the clothes and start it again. So I decided that I should call a certified serviceman to come out and access the problem. Today a certified serviceman came out to access the problem. After about twenty minutes I was told the tub needed to be replaced and the cost and labor would be $600 or more. I do realize that the washer is about 8 years old but to completely need a repair like a new tub. I am very upset and have no idea what to do.

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

Whirlpool refrigerators are best whenever I used many refrigerators. It provide many useful service to users. It allow us to store different varieties of products including vegetables, fruits, beverages and many more. It can make cube ice for to use in different drinks, products, etc. It consume less energy to used this Whirlpool refrigerator products. We used Whirlpool refrigerator with less stress of storages of fresh vegetables and fruits. Water is main thing we used to store in this fridge, it maintain temperature well for cool and fresh taste of nectar of nature. Nowadays, refrigerator are used widely in our locality especially Whirlpool which I mentioned them earlier to buy this awesome product to give comfort of mankind. I recommend Whirlpool refrigerator.

I have a Whirlpool top-loading washing machine model 3LA5580XSW3. The timer switch is not working and I have been told that spares are not available. Is this true? Everything else works well. Please advise as I really need a new timer.

I just bought this water heater on 2/12/12 and it has already started having problems. I got a self diagnosis of the gas valve needing to be replaced. I think that if this becomes an ongoing problem, whether I have a warranty or not, I’m going to trash it and go with another brand. I shouldn’t have to pay to have the gas valve replaced.

Purchased Whirlpool Microwave 1.6. The design has 5 BIG flaws. 1. Too large in depth, cabinets on each side cant open. 2. The one light under unit is so far to the back wall, you need a flashlight to cook spaghetti or use stove. 3. Too large in height, cant get a big pan on your stove. 4. Top of unit is open so much, if you spilled something from the cabinet above it would go right inside the works. 5. Instructions are hard to read & figure out, the wall hanging support is just one piece and if you dont have 2 main beams youre out of luck. GO buy a GE, put it up in 1/2 time & good & secure and works great. Has 2 lights on each side under unit. Fingers over the holes at the top. 1 inch shorter, 1 inch thinner. To my surprise the turntable is even larger, go figure.

My Whirlpool refrigerator, model number ET8MHJKXM005, constantly leaks water into the bottom inside of the refrigerator. Its only 4 years old, for crying out loud! I have a repairman coming over in a few days who tells me the newer Whirlpool refrigerators are notorious for having the drain ice up. Why would Whirlpool design such garbage? They should all be recalled.

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

BEWARE THE TEMP CAN BE 25 degrees off high and 25 deg lower and Whirlpool says that is within specifications. My oven temp was set at 350 and nothing was cooked... After 7 repair calls with their certified repair companies (the 2 worst repair companies that I have ever used) I was told that if you set your oven at 350 that if it stays in between 325 and 375 that Whirlpool claims that it is working fine and will not do anything. I called and talked to customer service and asked the lady that if you set your oven at 350 should it stay within a few degrees of that and she said YES.The people that work at Whirlpool do not even know what kind of junk that their company is selling. I asked to return it and get a more expensive model hoping that it would work better but they said that they sell ovens and do not buy them. Be sure to get in writing from your sales person that your oven will constantly hold the temp within a few degrees. I tried to do the Whirlpool survey but after 11 attempts they said that there was errors in receiving and they did not get it. If you buy Whirlpool then you did not ask the right questions. I WILL NEVER BUY Whirlpool again (unfortunately I have a Whirlpool dishwasher and refrigerator that are not much better) and if you do you will say the same things and be out Thousands like I am.

Whirlpool electric range with ceramic cooktop - I have a large black mark on one of the cooktop burners that appears to be beneath the surface of the cooktop. It’s almost within the finish of the burner and unable to be cleaned with cooktop cleaner. I have purchased an extended warranty and arranged for a service call. The repairman came out as scheduled, but informed me after making a phone call to who knows, because he did not tell us that the problem was cosmetic and could not be repaired under warranty. However, if we wanted a replacement cooktop, it would cost almost as much as a new stove. He also said that he had seen many of these ceramic burners with that problem and it was not unusual. All I really want is what is fair, a defect that is not my fault that needs to be replaced. The stove (Whirlpool electric range with ceramic cooktop) was purchased in 2004 and is kept very, very clean.

In August of 2008 I purchased a Whirlpool Amana refrigerator, Model# ABR2227FES. It worked great for exactly 6 years. In Aug of 2014, the motherboard needed to be replaced as it was not forcing a defrost when needed. I tried to get a refund on the cost of the part and labour but both were refused. In Dec 2016, just two and half years after the motherboard was replaced, the exact same problem re-occurred. Again I tried to get a refund on the cost of the part and labour but both were refused. Will I be buying this refrigerator in the future? A definite no!!!

I thought this was a nice high end washer and dryer set but it does not clean even wet mud. The mud just smears onto other parts of the clothes. My dog had an accident on her blanket so I threw only her blanket in on deep water setting, this is a large capacity washer and not a large blanket, the accident was still on her blanket when the cycle was finished. I had to rewash for another long cycle. Maybe its because it doesnt have an agitator. I was worried about this when I bought it and I will never by one again.

I absolutely hate this washing machine. When I bought it a couple of years ago I thought it would be great for large items... NOT! It leaves white residue on dark colors but the MOST important issue is going off balance. The lid stays locked and you have to start the cycle from the beginning... What a waste!!! Never again will I get a Whirlpool.

I posted about our problem with the Whirlpool water heater on the 20th. Chris ** of Whirlpool called me back. He totally took care of the problem and got us back working. After 3 years, our problem is resolved. I am grateful to Chris for finally resolving the problem. He was professional, courteous and knowledgeable. Thank you.

I purchased a Whirlpool gas water heater for one of my properties that developed an issue outside of the warranty period. My initial CS complaint is with Whirlpools IVR system, which was far less than a desirable experience. After tricking the system, a CS agent answered promptly but was not able to address my concerns. I asked to speak to a supervisor and received a return call from Chris within minutes. I found Chris to be patient and understanding of my issues. Chris promptly assisted me with my issues and offered an equitable resolution. Chris is whats right with American companies and domestic customer support.

My stove has met all my baking and cooking needs. Love the self cleaning oven and I mean it does clean every bit. Always bakes at right temperature. I love it. All my pies and cakes come out perfect and the look of it is just pretty and matches my kitchen.

We bought the dishwasher because ours was not a very good quality, and it was a Whirlpool and was larger than our old one. But the arrangement of the bottom shelf doesnt allow for effective placement of larger items. If you wash any large items it doesnt wash the top shelf dishes.

It has been a great refrigerator that has lasted for years without repairs. As of today, it is a bit outdated but still functioning. I hope it doesnt break now that I praised it.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

I have had our Whirlpool Cabrio washer and dryer (CU0771356 and MU0803512) for four years. Our trouble started when the machines were 14 months old. The numerous error codes have been fixed by replacing boards, the bearing has went out, and the entire tub has been replaced. The dryer has had two service calls for going out. Now, both are out again. The washer pump is bad and the dryer has stopped heating up. Where is the class action lawsuit?

Ordered this two days after my son came home from college. He had to be out of his apartment July 31 2016 and brought 4 years worth of laundry with him. Monday my machine breaks, Tuesday I order this thing from Lowes Arrives at 2:30 on Thursday and as it is being installed I ask why the water fill is so slow. It is trickling out like a childs toy. Delivery man tells me the water is completely turned on. He hears this remark a lot from people who buy this model. I put in my first load of laundry, a small load of about 6 things that I am washing for my mother who is in a nursing home. They have that nursing home smell. I push pause as the machine is cleaning to unlock the lid and peek inside. Oh my God the clothes are sitting on top of each other not even covered in water. I then shut the lid and listen to the tiny slush of the machine agitating. At the end of the cycle they smell exactly the same. Dirty.I had read to use the deep fill so I rewash them on deep fill. Look inside halfway through and what do I see? Wet clothes piled on top of each other, still not floating in water. How are these clothes getting clean when they are in a wet pile on the bottom of the machine? I take them out. Still not clean. Not smelling quite as bad, but not smelling like soap. I then washed sheets, a blanket, and some clothing of my sons. Nothing smelled particularly dirty but NOTHING smelled like soap. The quilt was covered in hairs (my son and roommates had a dog) and soap residue. I had read this in reviews online also. I am wasting time since each load takes from 50 to 130 minutes (yes). I am wasting soap, oh but I am saving water - not really.Well Lowes has a 30 day return policy so I went down there and am expecting a GE machine with an agitator tomorrow, Saturday! Cant wait. The only one saving money are these manufacturers They no longer are spending cash on producing the agitator out of plastic, attaching it with nuts and bolts, or using gaskets between the parts. DO NOT BUY THIS PIECE OF JUNK, do not even look at it. I question all the HE machines at this point. You need to use HE soap cause you cant wash away suds in a machine with no water. What a con - the whole thing is.

Bought a Whirlpool refrigerator December 2011, it is now 3 yrs. old, keeps shutting itself off. There is nothing under the troubleshooting area of the instructions for this. I called Whirlpool, they said I have to pay a tech to come here and troubleshoot. The warranty is 1 years, so after paying over 1k for an appliance, that gets you 1 year! I try to support American made, but no more Whirlpools here! I have all Whirlpool appliances, but Im guessing they wont last either. Very disappointed in the lack of customer service.

I have had this refrigerator for over 25 years and cant ask for anything better than that. Would buy another Whirlpool refrigerator. Has original french doors at top and bottom door on freezer. However, I dont particularly like the pull out drawer that the new refrigerators have now as I get so much more room with a door. The new refrigerators have improved rubber around the doors. That is the only thing I had to replace on this refrigerator.

I purchased a brand-new, $4600 36 gas range online. They finally installed all appliances by 10:30 pm last Friday, July 8, 2011. On Saturday, July 9, 2011, I woke at 2 am to weird smell (gas). I opened all the windows and went back to bed not sure since we never had gas before. Gas company came out that day and determined that the burners were bypassing gas. Jenn-Air said it was normal for some gas to come out and that they have sent the repair technician out three times to not find any leaks. The gas company red-tagged the stove saying it was hazardous. Jenn-Air has terrible customer service. I was on the phone Monday to Friday this week, every day talking with safety managers to supervisors with no results. This will be the LAST Jenn-Air purchase EVER!

After 5 service calls for cooling problem, under extended warranty, refrigerator was replaced. Had purchased 3 water filters directly from Whirlpool before problem. Could not use these filters in replacement model. In spite of that fact & filters in unopened factory package, Whirlpool would not refund the $100 purchase price because I DID NOT RETURN THEM WITHIN 90 DAYS OF PURCHASE, even though I wrote to their US president. Really unfair treatment & they could care less that I had to replace a defective product.

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2016. What a nightmare. Just a few months after having it, we kept getting an E3 error message that would not go away. After 2 weeks of waiting before a tech could come out there replaced a door mechanism said it would be fine. After the next wash same thing, same problem. Could not even open the door to get my laundry out. Again they could not get a tech out for at least 2 weeks so Im stuck with the cost of getting my laundry done elsewhere. This time it was the motherboard. Had to wait a week for that to be shipped out. This was all completed in June 2016. We are now the beginning of September and same problem. Again we are told at least 1-2 weeks to get a tech out. Seriously Whirlpool, we are your customer. I have a family and we need to wash our clothes. We spent $1200 on this machine only to have to take our laundry to a public laundry mat because your machine keeps breaking down. They will not replace the machine even though this is the 3rd time with the same problem. The customer service is horrible. They are not willing to help in any way to get this fixed much sooner for her or give us a new machine. This one is obviously a lemon! I will never purchase any Whirlpool appliance again and I suggest based on some of the reviews on here no one does. Next appliance I buy I will do more research for sure.

I have purchased Protton 3 door (Protton 20142, S.N **) fridge in Mar 2016 and since purchase of the fridge I have facing cooling issue. Its take around 24 hours to make ice. After sales service is also pathetic because after raised request the service person came about 6 or 7 days later, and he did not check anything and recommend me to go to the service center. I am not sure why Whirlpool kept this type service person and service. My concern is if Whirlpool is not ready to provide home service then should mentioned in service commitment we dont provide home service. I am using first time Whirlpool product and I realized Whirlpool product are very bad and service is also too bad. I strongly recommend to everyone please dont buy the Whirlpool product and I also want to know either Whirlpool will provide service or this fridge product is useless for me.

This washer is going back. It simply will not spin the water out of the clothes. It says it gets clothes drier than a conventional washer, but I have not found that to be true. I have to use the drain/spin cycle over and over and still the clothes are wet. I had the repair crew out and they were able to get it to spin out a very small load consisting of two sheets and two towels. Other than that, it does not spin out water. It is also very difficult to load if you attempt to leave the center open as they recommend. The cycles are very long. Not being able to look inside without pausing it and waiting for it to unlock is also a huge hassle. I am getting one with a glass top so I can see what is going on. If you leave it open for too long, it cancels the cycle and drains all the water, and you have to start over which is another problem because all your detergent just got drained out before the load gets going. It uses so little water on most of the cycles that the clothes get totally tangled up with one another. I think you should be able to choose the water level manually. I am all for saving water but if I want more water from time to time, this does not allow you to do that. I DO NOT RECOMMEND!

We have owned our refrigerator approximately 7 years. We have replaced this fan 3 times and now it went out again. The store we purchased it is now out of business. I am so flustered I do not know if we should replace it again or buy a new refrigerator, I can guarantee we will not be buying another Whirlpool. Their part runs about $50 but how do we know that is not going to go out again?

Thank God for this website and Frank of Dover (postings on Feb. 11, 2013 and Jan. 7, 2011). We just had exactly the same horrid experience with the lid on our Whirlpool Cabrio Washer WTW7800XW. Just as with Frank, our home warranty provider first accused us of abusing the machine. I merely printed out Franks comments and description, whereupon the home warranty provider reluctantly agreed to replace the lid. We also bought an extra lid and are keeping it in our attic for the next failure. Do not purchase this washer!

Love the design and style. It is an above the stove built-in model. And love the combination of microwave use and to have the ability to also use convection. It certainly has been an excellent purchase and would buy it again and would strongly recommend it to anyone.

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

Weeks ago, we received a new refrigerator from Whirlpool. Never really got down to temp. They replaced the compressor and still does not work. You would think a company like Whirlpool would replace it. That is a joke. They want to try and repair it again, another compressor? Now I have thrown out the food in it and feel like Whirlpool could care less. DO YOURSELF A FAVOR< DONT BUY ANYTHING MADE BY THIS COMPANY OR THEIR OFFSHOOTS.

I would not give this any stars! I purchased a Whirlpool gas range (model #WFG371LVB1) just 2 years ago at Lowe’s. The oven heats up to 475 no matter what temperature it is set at. The Whirlpool authorized service agent said it needed a control board which would cost $650 to install. The repair company found one for less--only $300. After reading all of the other complaints about these ranges, weve decided not to repair it and will probably have to replace it soon. We have been Whirlpool customers for years and will not purchase another Whirlpool product. There should be a recall on any of their products that have these continual problems. The oven cannot be safely used for normal baking.

My experiences using Whirpool ranges and ovens have been very positive. As a matter of fact, that is the brand preferred by my family through several generations. Durability, reliability and warranties have been the main features we have found useful. Most of the ranges and ovens have been replaced at home, always with Whirlpool brand, but with added improvements that manufacturer come up with, in order to integrate our devices to the latest technologies. I would recommend this brand to the readers, friends and neighbors.

Im guessing the company that makes Whirlpool appliances no longer make dependable appliances… bought home 2 yrs. ago. Bought Whirlpool over stove microwave and expensive side by side fridge. After 1 yr. microwave stopped heating. Now my fridge is no longer cooling. Have cleaned it underneath, did all a normal person would do. I replaced my microwave last year with a Maytag. I’m sure I will have to replace the fridge very soon. My stove is a Maytag. Dishwasher a Frigidaire... have had no problem. Just the Whirlpools… Will never buy another Whirlpool. Not just me, my niece bought a microwave. Her stopped heating after one year.

I just replaced our Whirlpool Accubake Double Wall oven, model RBD305PDS14, because it fried the control panel after being put on self clean. This was the second time this has happened and I have probably only used the self clean feature three times since we purchased the oven. Im not a specialist in defective product design, but having a control panel burn up two out of three times when the self clean is used suggests a significant problem. I refused to pay to have it replaced again and obviously did not replace it with another Whirlpool product or any other brand associated with the company. I see that this problem has a long history dating back quite a few years with Whirlpool doing little or nothing to resolve the issue. (They just deny any knowledge about any defect in the design.) Fool me once, shame on you! Fool me twice shame on me!

My wife and I purchased a Whirlpool Cabrio washer 1 year and 4 months ago. Its just three of us in the house. We never overload the washer. Now the drum bearings in the washer have gone bad. I feel that a washer should last longer than 1 year and 4 months. I signed up for the Whirlpool Repair Plus 1 Service Plan which is supposed to cover repair plus 1 year additional warranty. I was told that it would cost more than $1000 to repair so they would only return service plan cost. Whirlpool used to have a dependable product and dependable service. I dont think I will be buying another Whirlpool.

After 2 months of owning this fridge (Whirlpool Model WRF993FIFM) it started making a horrible buzzing noise that you could hear all around the house, both ice makers stopped working, and it wasnt cooling properly. After three technician visits, and of course having to miss work to have the technicians come to my house, my fridge still doesnt work. The most recent visit today was from 2pm until almost 8pm, yes seriously 6 hours, and now the noise has gotten even louder and my ice makers still dont work. AND after the tech left, my carbon monoxide detectors were going off for almost an hour. We had to open all of our windows and sit outside to not DIE of carbon monoxide poisoning. So beyond livid with this situation. Its been a month since Ive had a properly working fridge. Whirlpool needs to do right and fix this situation. I will be calling tomorrow first thing.

I bought this machine in September of 2014. Six months later I HATE IT!! It does NOT get the clothes clean and dont even try to bleach white towels or socks, it doesnt pump the correct amount of hot water and things come out just as dirty as when they went in. It tangles everything together and frequently stops working because it unbalances the load with its lack of water. Ive always been proud of how my familys laundry looked and now Im just embarrassed. Im considering donating this to a human society for dog towels. Stay away from this washer, its horrible. Im going to the laundromat and shopping for a new machine ASAP!

I purchased a Whirlpool Cabrio Washer WTW6200 & this yr purchased a newer dryer w/ steam capability. I wish I would have waited a couple months for a new washer that yr and purchased the one with no agitator inside! But my washer died that day & I needed one & NO ONE informed us of the changes or problems of this agitator at the time of purchase. I have had this service several times my first year and the agitator replaced I believe twice. But it still destroys clothing. I called 1 month out of warranty and even though they had been out several times the first year for the same issue, they would not help me! Yep, even after the 1st year they said to get things done I had to purchase an extended warranty even though this was a mfr issue no doubt! So, 3-4 years later I still am dealing with the very same issue over and over with NO RESOLUTION in site and $900 in the hole for this washer and I am losing money with clothing damage weekly!Even today I had two pair of jeans, $98 ea rec these terrible uniformed marks all across the legs making them unwearable! At least for where they were intended to wear them at. They are now yard jeans...yep $98 expensive yard jeans now!!! These were my good jeans which I cant afford to buy more nor replace them so I have to do without. We cant wash anything with strings such as hoodies, shirts or baby clothing with spaghetti straps or little dangle things; we have to use the laundry mat and come home & dry w/ my Cabrio steam dryer which I love. Most everything I have to use zipper net bags but even then things still can get destroyed, especially if a hole gets torn in the bag from the wings of the agitator as you will see in the below photograph. I currently have & own an expensive washer I purchased from HHGregg by Whirlpool replacing a previous whirlpool I owned for 22 years! Yep, Im wishing I had it back & put the $200 some needed to repair it! Please Whirlpool will you please do something & make this right once and for all. I dont have $900 for another washer. I just want to be able to use my washer without it destroying everything I own. I have darn photos of what this is doing and you wouldnt believe it. It took us an hour, yes an hour to untangle a top that became entangled in the flaps on the agitator. This is the worst design I have ever seen and needs to be recalled once and for all and either fixed or replaced with new machines of equal model with the agitation issues resolved or removed & with no issues or further costs to your customers! Why would you honestly believe that an agitator with wings coming off the bottom that are not attached to the bottom would serve some type of positive purpose in cleaning clothing? All it is doing is tearing them to shreds, tangling them up, doing things to hoodies which make them unrecognizable after ripping the cords so hard out of the hoodies that Ive seen them shred the material across the collar area and opening of the cording completely ruining hoodies ranging from $35-$75 a piece even after placing them in mesh bags! Why did we keep placing hoodies in the machine? Well with 4 children at times they just dont listen or get all the info as to what is going on with the machine as 3 were college kids coming home periodically & yes, to do their laundry. Look, lets talk straight. You as a company from what I have learned from appliance salesmen locally and regionally, you knew this was wrong and knew this was your last ditch effort of an agitator before you knowingly knew you were going to an agitator-less unit on your washing machines & already had one ready to go out on the floors. I know that you Whirlpool CEOs knew this unit was a bad call but chose to ignore it. You had to know it because there was no way this could have passed quality control. It had to have failed sometime in its trials showing you the issues of the wings. Unless you never did any quality control on this unit and just rushed it through? Please to the CEOs of Whirlpool, I am asking you to make this right if not for good standing of your company do it at least for families like myself who cant afford to buy another machine and are now stuck with NEW machines yet going to Laundry mats. This was to be my last washing machine I would buy hopefully. I am 54 and was not planning on buying another. How do you think this makes your company look???? Im just so tired of dealing w/ Whirlpool to only hear I have to purchase a $400 extended warranty with no guarantee that they will fix the issue. If an attorney wants to step in & believes they can help us and maybe others then Yes please help us because this is absolutely ridiculous and is a product that needs to be recalled. We are out so much money now and like I said we are to the point we cant purchase another washer. We had to purchase all new appliances as they all began going bad around the same time.

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

I have owned a Whirlpool Cabrio model no. WTW7800XW2 washing machine for less than 3 years. The plastic frame for the top glass lid cracked (on the right next to the spring loaded hinge). After reading that other people have had a similar problem, I contacted Whirlpool about this and talked to its TN call center representative. I requested that Whirlpool repair the appliance free of charge since there is a known defect with it. She said Whirlpool would only offer me a 50% price reduction from the retail cost of the lid plus charge me shipping and taxes. I will not be buying another Whirlpool product as a result.

I have many rentals, and for over 39 years have always bought Whirlpool dishwashers for them and my own home. I have noticed over the last 15 years or so they are getting more and more poorly made. First I quit buying the plastic tub ones because they collected mold on the back. Then putting one in a rental, we went through 3 brand new ones that all leaked before we got a good one. Now, I bought the very best for my home 2 years ago, had the pump replaced under warranty due to leaks. Now, the plastic upper rack wheel has snapped off its plastic base. For under 30 dollars you get a replacement kit for it, that is all metal. So why didnt Whirlpool just put in the metal ones and charge a little more. So this will be my last Whirlpool, and all the brands they make. Do your research, many of the name brands you know are all made by Whirlpool.

I purchased Whirlpool washer in 12/2011. Immediately, I noticed the noise and called service. It was a whistling noise. The clerk told me nothing was in the manual and it would cost $65 to have a tech come out. He advised me to wait until it was louder and more consistent. I called again when it was. Gear case was replaced on 5/2/2012 five months after purchasing the machine. I called Whirlpool again in 5/2013 - same problem. I was told the diagnostic call would be $95, labor which is extended for a major job is $85 and the part would be $290. It would cost $470 to repair as the gear case was guaranteed for only three months. This machine is a lemon since the gear case is now shot again prior to the machine being 1-1/2 yrs. old. I called Whirlpool and spoke to Amy (Esc. Sup.) who advised they would replace the part only. The appointment was scheduled; the tech came, did diagnostics reading a manual and said the gear case is shot. I inquired, Well, you are going to fix it today right? The reply was, Oh no, it has to be ordered and its a two-man job. When I arranged for this appointment, this was clearly explained and what I was expecting, two men and the part to be replaced with them. Now its a five-day wait to get the part and then a scheduling issue when they could do it. This machine is a lemon and Id like to have the machine replaced or my money refunded. This is a runaround, scheduling the appointment and having someone show up with the manual and having no parts and not knowing that it was the part which broke again from previously being replaced.

I had an electric 36 Whirlpool, smooth top cook top for 18 yrs. Worked great, cleaned with Windex and occasional scraper. Didnt show streaks or spots. I remodeled my kitchen 10/15 and bought a KitchenAid 36 glass smooth top vented cook top. What a piece of junk. Wish I had kept my Whirlpool. I can not get it cleaned. Every little fingerprint, mark, etc. shows. I thought KitchenAid was an upgrade to whirlpool but I was surely wrong. I am glad that I didnt change my built-in double oven. I did change out the Whirlpool quiet gold dishwasher for the KitchenAid. Again, wish I kept my Whirlpool. The KitchenAid is noisier, looks terrible with the stainless inside. Im embarrassed to open it with all the water stains. My Whirlpool was white inside and looked like new. I wish I had the money to change it back but I dont unfortunately. Moral of the story is if it aint broken dont fix it!

The machine is reliable, does not take forever to do a load, it is relatively quiet. It has sufficient options depending on the size of the load. Additional options are time setting, choice of warm, cold or warm/cold water settings. On light and medium loads it extracts almost all of the water; on heavier loads an extra dry spin does the job. In all the years that we have had it, it has required only one service call. The maintenance man told us that this model is the best in a series and he recommends that we hang on to it for as long as possible. We're very happy with it.

The oven will not turn off. When I called Whirlpool and told them what had happened they immediately put me in contact with the safety division. My question is if it is a safety issue, why is there not a recall and why do I have to pay for the circuit board. If there is a safety issue why is there not a recall.

Right from the start of buying a new suite of Whirlpool appliances, the light over the range burnt out. We figured it was just a bad bulb so we replaced it. Soon it burnt out again, replaced it again, then again it burnt out. I finally called Whirlpool about the problem and found out it is the electronic panel that needs to be replaced... Of course at a full charge to me! I am so over WhirlPoo, (yes I spelled it that way on purpose) every single appliance has had issues. I have just lived without a light over my range because fixing it is more expensive than buying a whole new microwave. Never again will I buy any WhirlPoo appliance!

I installed this Whirlpool Gold Series oven in December just before Christmas. I cooked a 9lbs Turkey for over 4hrs at 350 degrees (it should have only taken 21/2 hrs at 325) used a thermometer to test the temp. Well the breast part was fine but later in the evening I removed the entire turkey only to find that the legs, thighs and bottom of the turkey was still RAW. Lucky no one had asked for that part of the turkey. Next I tried a small prime rib roast. Same thing happened. The top of the roast was fine and the bottom was RAW. I dont dare cook anything in the oven now. Called whirlpool and they are going to send someone to look at it but I wont hold my breath for any results. After reading the same complaint on several reviews and the TV show Marketplace it seems to be pretty standard for this product.

We purchased our Consumer Reports rated #1 best washer, seven yrs. ago with a five-yr warranty. We have had nothing but repair after repair starting in the first year. The mother board replaced twice, the entire inside had been replaced within four years. It is only a household of three, the washer looks like new! The machine is now making a noise like a freight train... We had a repairman out $95.00 just to look at it! Cost of repair $1,116.21!!!! More than what the machine is worth. The replacement parts wore out in the last 2.5 yrs, again poor design. I contacted Whirlpool during the last repair issue and demanded a full replacement. The customer service rep, as RUDE as can be, checked with her higher-ups and said they would replace it for $845.00!!! WHAT A JOKE. I could buy a new one for that! The repair person said they are one of the highest repair units and the most costly out of warranty. He had one with the same issue just two days prior. I will never buy another Whirlpool product or purchase from H&H Gregg. They sold our warranty twice losing all of our repair records! It looks like I had an extra load size dumped on me!

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

Whirlpool is the manufacturer of most appliances including the Kenmore dishwasher. Your products are made horribly for the mother board to go out in 2 years is ridiculous. I purchased a stainless steel dishwasher from Sears in August of 2014. 2 weeks ago I received error codes E2 and F2. A technician came out and the mother board needs replaced because water got into it... its a dishwasher. The cost to fix $465. I paid $673. The sales person informed me that I should have purchased the extended warranty because the appliances now only last a few years. Seriously... fleecing of America. This is my last purchase from Sears. We have bought appliances for 30 years from Sears and this is the end. They could care less about customer service or their products. Apparently everything is now made by Whirlpool who will also be getting a review. Shame on you for making poor products.

I hate my Whirlpool refrigerator: It has a upper freezer with no light. The shelves are not split and raising or lowering shelves gains nothing and may even take space away. I would never ever buy another Whirlpool.

After careful research, I purchased a Whirlpool microwave 2 years ago. Model WMH2175XVT-2. It looks brand new. Three months after the extended warranty expired, my microwave wont heat anything. Ive tried all the suggested troubleshooting in the manual. When I called Whirlpool (the number right inside the microwave door) I get a recording that asks me if it has been more than a year since my purchase. I can only say yes because even the extended warranty with Sears had expired by three months. Then Im directed by the auto-operator to schedule a repair service. Im fuming and seeing dollar signs and no human to talk to, so I hung up. I googled my problem and was asked to pay $50 by an online repairman, so I clicked out of that window not wanting to sink more money into a bad purchase. Then I found a website from a consumer saying the Whirlpool Company admitted it was a bad magnetron with this model and that they have had a lot of problems. They should have recalled this microwave model or offered to repair or replace it for free. I have just decided that I will no longer purchase Whirlpool products. As soon as my oven and dishwasher die I think Im going back to Kenmore products.

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

This dishwasher (model #WDT710PAYM5) leaked water after having it for 9 months. Service man came out to look at it and said it wasnt level. The very next day when I use it the water came out again on my wooden floor. Now the wood floor looks like it has water damage. Sadly this floor was just installed.

I would not, at this time, even really give this product 1 star, but that was the lowest rating allowable. We purchased a Whirlpool Gold French Door Refrigerator at Lowes a couple of years ago after our Amana was toasted by a close proximity lightning strike. (It got more than just our frig, but the replacement frig is the only item we have had issues with.) We even got the extended warranty thru Lowes for the unit. Shortly after the extended warranty expired we started having issues with the bottom freezer door icing up. We thought that possibly the grandkids had not shut the freezer. So we cleaned up the ice around the door, but the problem persisted.The ice cream in the freezer was rock solid, to get it out of the container you had to put it in the microwave for a couple of minutes. The items in the frig were also frozen. So we emptied the frig and freezer, unplugged the unit and let it sit for a couple of days with the doors all open. We then plugged it back in and hoped for the best. It seemed to be ok for a couple of days then the ice on the freezer door appeared again. At this point, I contacted Whirlpool to see who was a licensed repair company in our area. I contacted the licensed repair service, explained my issue, they got the model and serial number info and ordered what parts could conceivably be the culprits.The tech came, the unit was frozen up, all the vents in the freezer were showing icing. So he removed the back of the freezer compartment and thawed the unit out. At the same time I mentioned that the ice maker had quit working, he found that the wiring connection was not properly connected and fixed that while he had all the stuff out. After re-assembly he ran all the diagnostic tests Whirlpool lists and found everything passed. Since the boxes of parts had not been opened they could all be returned to stock. So no charge for parts, as he could not find indication that any were needed.So 1 service call at $100 and it appeared that maybe the issue was resolved, not the case. Not even a month later, issue re-occurred. No grandkids had been there, no instance of the freezer possibly left ajar. Another service call, and by the time the tech arrived, since I had unplugged the unit and emptied it again, all the frost/ice was melted. $100 for a service call, tests all came back as nothing indicated as not functioning.So if I dont put too much stuff in the freezer or too much stuff in the frig it will run without freezing up for about a month. Oh and weekly put it into the defrost mode a couple of times. Now it has started making a tic-tic-tic or rat-tat-tat sound to the fun and games. If the noise is non-stop, it only stops when you open the freezer door. Leading me to believe it is a fan. (Correct, I was told by the local Whirlpool licensed repair facility.) I have spent the weekend, again thawing out my unit in hopes that the noise will cease. It is loud enough to be heard at the other end of the house.No such luck, so I spent an unproductive 1-1/2 hours on a call to Whirlpool yesterday. The larger part of the time was on hold waiting to talk with someone, anyone. Due to our unusually high call volume, wait-time is long today. Thank you for your patience. To retain your place in line, do not hang up. Finally, I got a rep named Karen, who sounded like she was almost asleep. She had very little to offer except, Im sorry you are experiencing these problems. I have no record of previous complaints like yours on record for this model of our product.Hello, I found 929 reports of the same issue on Consumer Reports. Oh, you cant believe what you read on the internet was her response to that tidbit. She offered to sell me a Repair Plus 1 Plan for only $359.95. A licensed repair service comes, repairs your unit and the plan gives you ONE YEAR of peace of mind. Lets see... I said... so you are offering me an extended one year warranty? Oh, but it comes with a repair first then one-year peace of mind. Seems that Whirlpool has moved into selling warranty extensions rather than fixing the issues with these Whirlpool Gold French Door refrigerators. With what I have already paid for service calls added to this Repair plus 1 Plan, I would have invested $$$ enough to BUY A NEW FRIG that is not a Whirlpool product.Seems a bit foolish to me. So Whirlpool is not admitting that there is a design or manufacturing problem with these units. Even the ones sold just this year seem to have the same issue. They have not corrected this and it appears they have no intent to do anything about it. She did indicate that they had a known issue with the drain and that a fix was offered for that (a redesigned drain unit could be installed). But since I was not getting ice build up on the bottom of my freezer compartment I did not appear to need the redesigned drain unit. Her evaluation of my issue was that the drain did not appear to be a problem.So after a fruitless call to Whirlpool, oh and they did have my previous emails concerning my issues on file but did not consider my complaints to be part of a known issue, I have the local tech coming back to see if possibly there is something, anything to be done with this refrigerator. So another $100 at least, likely no resolution if the service tests all come up normal again! So when the tech comes, I am going to ask him to contact the service engineer that he is supposed to have the contact info for (per Karen at Whirlpool) and see if he can get any resolution to my issues by using that service engineer.

I have purchased one refrigerator double door Mastermind 230 Ltr. capacity on 08/02/2009 at a price of Rs17200 from Himanshu Sales at Halol, Panchmahal, Gujarat. After one year, there was a problem in the refrigerator. My complaint was given to Himanshu Sales Halol. A service engineer came and replaced OLR and starting relay. I was charged Rs500. The bill was not given. Again cooling was not achieved. My complaint was given to customer car complain no. 22265 on 26/04/2011. Service engineer came on 10/05/2011 and reported that compressor get overheated. He has replaced compressor, capillary, gas, starting and overload relay and charged Rs1650. But compressor continued on, it does not cut off on temperature. I complained on 22/05/2011. Again service engineer came and replaced thermostat and charged Rs150. On 02/06/2011,again cooling was not proper. I complained on 05/06/2011. Service engineer came and advice to send the refrigerator to service center at Halol at our cost. After one week, it was sent back to me. Still ice not forming in freezer. We thought that it is due to summer. We also informed Himanshu Sales Halol. They advice to give complaint to customer care. Complaint was given on 28/11/2011. On 29/11/2011, a service engineer came and informed us that the compressor overheated. On 06/12/2011, the service engineer came with new compressor. He replaced the compressor, capillary, starting and overload. After gas charging, fridge was started. Still ice was not forming in the freezer and there was abnormal sound coming from compressor.Now we are tired to take service from Whirpool. I think this is a company defected piece, so send some senior authority to check the same and to take necessary action. Also due to this problem, my electricity bill got on higher side, and the purpose of the appliance is not solving. On 12/12/2011 at 11:30, the service engineer came and put some instrument to measure temperature at freeze on super cool mode and told that he and Samir will come to check the same. After that, compressor was in running mode up to 19:30 without cut off on temperature. Nobody has came to check,we called him. He replied that Mr. **, the regional head, will come tomorrow, 13/12/11. Still cooling is not achieved, We have registered complaint under complain no. AH1211007719 dated 13/12/2011.

We bought the dishwasher on 12/28/11. It broke 4 weeks later. I had the company come out to fix it. 6 months later, it broke again, needed a whole new control board. 3 months later, it broke again, they came out and did some type of repair. 7 months later, it broke again and it needed a whole new control board. They wanted to charge us $250.00 for this, but after some major arguing in regards to how New this was and the warranty now out, they waived the fee. 3 weeks later, the same problem as before! I am so angry about this lemon of a dishwasher! They are coming out again today! I am quite sure they will need to replace the control board again! I will never buy another Whirlpool product.

Whirlpool refrigerator runs continuously, but doesnt cool. I have to turn it off manually to cool down the motor. I have to run it on the highest number (5), then freezes some things on the top shelf but lower shelves are warm. We need these refrigerators and freezers replaced with different brands of our choice!

I purchased a Whirlpool washer in 2005. After the extended warranty expired, our washer broke. The Whirlpool manufacturer did not have parts in stock. It’s on backorder, so what does that tell you? So we have had to wait for over a month for the repair shop to receive parts from Whirlpool’s manufacturer. Service is very slow and the quality of product is very poor. After five weeks and no repair parts, we are going to have to purchase a new washer since we do not have our washing machine repaired yet. I promise to never purchase a Whirlpool product again.

AquaLift Self-cleaning does not do the job as advertised. It does very little to clean the oven. Sitting-on-the-floor-in-front-of-the-oven scrubbing is what is needed to clean the oven.

I bought my Whirlpool Convection oven in mid August 2019 from Lowes. I have had to call no less than 5 times about my NEW oven which I am extremely remorseful of buying. I am so unhappy with my experience mostly due to my expectation that my new oven would have been able to meet my demanding needs baking and cooking. I would have thought that it would have lasted longer than 4-5 months. The bottom left hinge is faulty which I am told is an undocumented problem for this particular oven. I noticed that it was having a problem when the oven wasn’t quite making a seal. Slowly it got worse until now it makes an initial click then I can open it about 5 to 6 inches and then have to lift it up so that I can open it without making a horrible noise and a dent in the frame.The first time I called was on Saturday Jan 4th. It took me 1 hour to get through to speak to a person. I asked why I couldn’t get a new door to the oven and they told me the hinges have to be installed separately because this model is made to be able to take the door off for cleaning purposes. They set me up for service on Wed Jan 8th between 12 and 4p. I wasn’t as unhappy at this point. I even got a text saying that the appliance company would be coming between 12 and 2. At 12 when I woke up after working nights, I got a message saying that they hadn’t received the part yet and that there would be no point in them coming. I called Whirlpool again and they told me that the part was on backorder and that in fact the part had to be fabricated and it may take up to 10 business days but that they would have the part sent directly to my house. By this stage I am very unhappy.I called back this morning and told the person that I would rather have a new oven or my money back and that my less expensive and less decorative oven that came with my house lasted me 20 yrs. I get a lot of “I’m sorry” and “I apologize” but that doesn’t fix my problem. I also told them that now the frame of the oven is being dented so I am going to have a less than perfect appliance which is no fault of my own. The only info the person could give me is the tracking number of the part they were able to locate which would be coming Fedex.I tracked it and it was due to come no later than Tuesday night. So I called the original service company in my area who told me to call to set up the service time when the part came in. I figured I would get a jump on it and call. They told me that they were all booked up this week and I would have to wait until next week. Do you think that this is how your customers should be treated? I feel as though I am being punished by choosing to buy an appliance from Whirlpool. I then tried calling back to set up an appt with a new company but the wait time was too long. I had just worked nights and needed to get some sleep. I called back this afternoon and again had to explain the whole situation AGAIN. I was able to set up an appt with a different company for Monday between 12 and 4 which happens to be on Martin Luther King day…so I am hoping it is not a mistake.Do you think this is fair treatment for a customer who just bought a brand new oven less than 5 months ago? Would you like this type of service? Would this give you any confidence to buy products from Whirlpool? I don’t believe that I would be able to recommend Whirlpool in good faith. The people who I have talked to have never been rude or disrespectful however, I feel as though my unhappiness is just par for the course. I feel as though it is just my tough luck and “oh well so sorry” instead of the attitude that you want to make everything right as quickly as possible. I ask myself if the problem was the store I chose to buy from? If I should have gone to Sears and bought one of their products or where I went wrong.

I came back from vacation and found a sheet of ice at the bottom of my freezer, just like that lady from SC and some vegetables frozen in the vegetable bin; not very happy. Have not contacted anyone yet, but I’m very unhappy about this situation. This refrigerator is less than 2 years old; I’m afraid of putting anything in this unit as it is very undependable.

Bought this washer NEW 4 yrs ago. Now sounds like a freight train in the house when in use. Whirlpool customer service is absolutely USELESS!!! They do not stand behind their product and refuse to acknowledge what is a common issue. PISS POOR and will NOT give me a number to a higher up. Absolute disgrace!!!UPDATED ON 10/28/2015: This is an update to my previous review. 1st, I contacted Whirlpool who was absolutely NO help whatsoever and the person I spoke to refused to put me through to higher ups on the food chain. I was wrong in my previous review when I stated that we purchased the washer & dryer 4 yrs ago. It was purchased in January 2012. Started making noise in 2014 and has progressively turned into the sound of a freight train. I also failed to mention the stench that comes from this machine. It has also got to the point where it quits with 10 minutes to go in every wash. Whirlpool did send out a Whirlpool certified technician, which they paid for, who stated this has been a common issue with these and other models of Whirlpool Cabrio wash machines. Says in his 3 yrs with the company he has seen and diagnosed over 30 machines with basically the same issues (bearings are SHOT) and Whirlpool refuses to accept any responsibility for the defective design and that, in his opinion, they shouldve never been released. He gave me an estimate of $257.13 to repair. We decided to go ahead with the repair and technician came out only to tell me that there has been a re-work in the design of the replacement parts as Whirlpool realized they were faulty. So I now have to wait for the NEW designed replacement parts to come in as they are back ordered. WTF does that mean??? Shouldnt there be a RE-CALL and shouldnt they accept responsibility for this??? This has been, without a doubt, the most disappointment weve had with any purchase of a NEW appliance or, anything else for that matter, in our lives. After reading through some of these same complaints Im wondering if this machine is nothing, but a money pit and whats going to go wrong next. We also purchased the Cabrio dryer at the same time and have had no issues with it as of this time, but I assure you, I wait with baited breath. Their customer service department is piss poor AT BEST!! Please, stay away from ALL Whirlpool appliances in the future.

I purchased a washer and dryer set, the Cabrio Platinum Series WTW8500BRO, about 3 years ago. I had a UL code come up a year ago and the machine was serviced and all was back to normal. Then only 9 months later it started acting up again. This time it sounds like an airplane taking off and there is a black spatter leaking from underneath, also the lid lock stopped engaging. I started to look up the error code for the lid lock and while reviewing that issue it was an easy fix, however, the noise and black spatter issue led me to tons of horrible reviews about this product. It is a bearing/tub/shaft issue that is going to cost me $500 to fix. First off I did not pay cash for this set, I rented it for 3 years and paid twice what it’s worth, around $4,000. Stupid on my part but I couldn’t afford it the other way. Weekly payments were easier. Now I am scared to fix this product because of all the reviews I’ve seen from other consumers. I haven’t had the other issues like dirty clothes, not enough water, high cycle times because they all start with a high number but after it configured the load the time shrinks, but this major issue about the bearings, they say I have to replace the entire tub assembly which is half the cost of the unit. So stupid and I cannot believe Whirlpool is getting away with this crap. Please please please inform me about any lawsuits. I will gladly participate in that. They should be held accountable for such a worthless piece of junk. Like I said I am now afraid to fix this machine because from what I’m reading, more than likely it will only last a short time.

I purchased this washer (Whirlpool Cabrio HE) 2 years ago against the advise of many people including my husband due to the cost, $850 for what is now no more than a large paper weight! It had never really done a good job at cleaning our clothes. About 6 months ago, it started not spinning enough to remove all the water from the load. I thought, no big deal, I will just use the extra spin cycle. It became the normal thing - wash, spin, extra spin. Well, then it became wash, spin, extra spin, extra spin. I noticed 3 months ago that it was not even agitating. It fills up, sounds like it is agitating and then drains. There was no movement from inside at all. All along I am getting from my husband. told you not to buy it! I gave in and called the repairman - $185 for a console, $26 for a sensor and $55 for a couple of drum clips and then the $35/hour for the repairs. I would rather spend a couple hundred dollars and buy a washer with an agitator that really works. I would never recommend this washer to anyone!

Whirlpool Gold Refrigerator Control Panel Failure - This French door refrigerator with freezer on the bottom was purchased new in November 2008. This August, the refrigerator stopped cooling. I contacted a reputable local appliance company who diagnosed the motherboard was not functioning on the appliance. They ordered a new one from Whirlpool and replaced it. Forty-five days later, the replacement motherboard stopped functioning. When I contacted Whirlpool directly to inform them what was happening, they continually stated that the appliance company was not part of Whirlpools approved appliance technicians, and offered no assistance in guaranteeing the problem will not continue to happen. I am extremely disappointed with Whirlpools customer service and unwillingness to guarantee their products. A 3 year old refrigerator should not stop working.

I purchased a lot of Whirlpool appliances -- washer/dryer, dishwasher, microwave, and now a Whirlpool stainless steel refrigerator. This was approximately the end of 2014. Not long after I purchased the refrigerator, the front started with small rust stains. I notified Whirlpool and all they said was call Scratch-b-gone in California. My refrigerator should have been under warranty. They offered no other help. I live-chatted this morning and they say the same thing -- call another company. You are now out of service. Im so very disappointed in Whirlpool and will definitely rethink purchasing another Whirlpool appliance. My other stainless steel appliances are not having a rust problem -- just the refrigerator. I havent tried the Scratch-b-gone yet because on their website they say that a lot of Whirlpool products have a coating on them. VERY, VERY unhappy with Whirlpool and their customer service...

Whirlpool washing machine was not a good buy at all specially after using it and seeing that over the years I had to incur high costs of maintenance. Over the months and years of buying Whirlpool front load washing machine, I had to replace motor twice, digital display twice, motherboard twice THAT TOO at a very high price every time something broke. This time the angle that supports the drum broke and Whirlpool says drum needs to be replaced. HOWEVER, after waiting a month company says DRUM IS UNAVAILABLE. Which means my machine has become absolutely useless just because Whirlpool does not have the spare. Whirlpool has a ridiculous track record with poor service and poor product quality. Manufacturing in one country and selling it in another WITHOUT SPARES is defective and poor service, totally unreliable. Wouldnt recommend Whirlpool to anyone.

These products (Dishwasher, refrigerator, cooktop, and wall ovens) are less than 5 years old and everyone of is in of repair. The cooktop and wall ovens the repair on them would equal the price of a new one. I feel that the products should last more just a few years and also their warranties. This tells me they do not stand by quality of their products.

Whirlpool Washer Front Loader - Ripped off! It cost $250.00 to repair; the serviceman was at my home all of 15 minutes. The below or otherwise known as the rubber seal was ripped up and caused my washer to leak water all over the floor. I washed a load of laundry, 1 item being my 2-year-old granddaughter’s pants that had a 4 zipper in the pant leg. The serviceman suspected the damage was done by the zipper. So how many of us wash clothes with zippers?!I called and ordered the part from Sears thinking this was possibly something we could fix ourselves, only the part was on back order and would take a month before it was in. Therefore I looked online and could purchase the part, delivered for $91.00. I called for repair service to ask them about it. He said they could be difficult. It would take him about an hour to put it on. Guess what, it was on in 5 minutes. Now, Im even madder because I know I could have done this myself. Whirlpool! Oh yeah, I forgot to mention this was 1 and a half years old; we’re a family of two, no warranty. Think people, we’re getting ripped off.

I have the Whirlpool Gold microwave model GMH3204XVQ-1 manufactured in May of 2010. The plastic around the lower door handle is cracking (currently in 4 directions from the handle) and the plastic on the side of the control panel is cracking in the center area and lower side. Neither of these area experience abnormal stress in day-to-day use. Unfortunately I could not get a good photo of the other crack on the lower corner of the control panel but included the one on the side in the middle. I contacted Whirlpool customer support about 1-2 months ago and to date, have not received any type of response or concern from them about this issue.

My 5-year-old Cabrio started coming up with error codes, and not draining and spinning the clothes. I called a week ago, they offered me 2 options, one being put $339 on a credit card and that would cover all parts, labor, and a 1 year extended warranty. They charged the credit card immediately for the biggest piece of crap washing machine. Someone came out 2 days later and told me he has worked on a lot of Cabrios but never one in quite that condition. I was led to believe that after charging the credit card, boxes would be arriving with parts to fix it. I called 2 days later to find out the status of when it would be repaired and they told me they already put a credit thru on the credit card because to fix it would be equal to the price of 2 brand new washing machines, and they will do nothing to honor that agreement. So I now have a piece of ** in my laundry room and takes me two days to do a load of laundry. DO NOT BUY THE CABRIO! In fact Im not going with a Whirlpool ever again!

We use a Whirlpool Washing Machine and it is one that came with this apartment provided to us by our employers. My parents had a Whirlpool Washing Machine too and they have had no problems since I have known them to use a Whirlpool. The Whirlpool that we are using has been very reliable in the past 3 years we have been using it. No issues whatsoever! The clothes do come out clean, so it does it's job! It is a top loading washing machine as opposed to the newer front loading ones. I have not used a front loading washing machine, so I do not know how it compares to them. The settings on our Whirlpool are basic and very easy to use. (If you know what you are doing, of course). LOL! Reliable is the word for Whirlpool!!

I love the large capacity of the washer. But something is turning my whites YELLOW! I have never had this problem in 40 years of washing clothes. All of my whites come out yellowish and I am getting what could be rust stains on heavier cloth (white denim). Also, I regularly used the soak setting on my old Whirlpool. That setting is not available in the Cabrio. I have tried catching between cycles and the drum is constantly emptied. I wish Id read these reviews before I bought.