I wrote down names, but I will not say them here. I found many recall sites on Whirlpool Cabrio WTW6200vwo for washer tub bearings. Which mine are bad. I called and logged my complaint but they say they have NO recall on any of their products and will send someone out but will charge me a service call unwarranted and parts if needed. I told them there are many websites that recall their tub bearings but they refused to fix the problem on recall. I dont have photos due to bearings are under the tub.

We have a built in double oven and we had some early problems with the thermostat. And from time to time the clock resets to 12:00 oclock when there is no other power outage indications. Its also been a challenge understanding the instructions sometimes.

I am writing to you all today to urge you to not purchase Whirlpool products specifically Whirlpool 2-cu ft High-Efficiency Front-Load Washer. I purchased a front loader washing machine for our tenants through Sears back in June of 2013. When it was hooked up it had an error code on it so we contacted Sears and 3 weeks later they sent out a repairman telling us it needed a new motor (this machine had not even washed 1 load of laundry). They ordered the part and Sears paid 1200 to replace a part on an 800.00 washer.....yeah I know dumb right. Well the part replacement did not work. (Surprised) They ordered and delivered a new washer 1 month later....same error code. Lets try again with another washer......same error code. How about another one......water would not stop running into the machine because the sensor was broken. Wait we are not done how about another one.....same error code. No I am not kidding, 10 months later 5 washing machines and my tenants have yet to have been able to wash a single load of laundry. I have been reimbursing my tenants every month for not having a washer for the past 10 months. I finally had Sears reimburse for the washer which they will pick up soon. I am out all the interest for the past 10 months for a product never used. To top it all off I called Whirlpool directly to see if they would be willing to at least give me a coupon for any amount toward the purchase of a different washer. They told me quote We dont do anything to compensate our customer for their troubles. That is the icing on the cake folks!!! I will never purchase another Whirlpool product and I encourage you all to not as well. I want to show them how not caring for their customers can impact them. Please share if you can, but more importantly please pass the word!!!!!

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.

We bought a Whirlpool gas range about a year and half ago. The oven started giving lighting problems we had to light with a match every once in a while. Then the broiler igniter started giving same problems so I replaced the igniter, still did not work. Then I tried the control panel, still nothing. The igniters were about 45.00 each. The control panel was 250.00. Then I replaced the spark module and it is now working. Some models the spark module dont control oven and broiler but mine does. That was 200.00. The best thing was the part place I was ordering from would exchange the parts that you try and they also can answer questions either online or by phone, Appliancepartspros.com. My oven model # is wfg371lvs3.

Refrigerator model LFFU17F5HWD - For 2 years it worked, but with problems - always frosting over. I called a service tech and they said it was a common problem, but to find a service tech to come and look at it. The cost for that was $250.00 and still no fix. Now it quit working completely. I was always told by my dad that Whirlpool was the best - maybe true, 30 years ago. I know one thing if I have to buy another refrigerator - it wont be a Whirlpool. You do stand up to your name Whirlpool of trouble. If anyone reads this, please take my advice and do not buy a Whirlpool. I have a washer and dryer thats Whirlpool too. They work but I wont have anything in my house that says Whirlpool on it. Its too bad that they were a great product at one time. Consumer Reports should do something about this company or the BBB. Im so mad I cant even spell well. Thats my 2 cents on Whirlpool of crap.

I exchanged my fancy front loader Cabrio washing machine for a top loader after having numerous issues: clothes werent getting clean, extended water cycle, and a leak. The original purchase was made at Lowes, where I elected to invest in the 3 yr extended warranty plan. After several visits from their sub-contractor, they allowed me to exchange the washer for a top loader Whirlpool Cabrio. At first the washer seemed to work, but after about 8 months I started having problems. The bearings went out and when the service company replaced it they forgot to screw top of the machine together. During my first load, I heard this terrible noise and discovered that the entire top of the machine had separated from the bottom by 2 inches. I frantically rushed to turn the washer off before my laundry room flooded. So, they were out again and screwed the machine back together but failed to retrieve the original screw that they removed from the washer during the first round. Well, the screw got lodged in-between the drum and interior, causing it to completely break the machine. Lowes agreed to exchange the washer for another top loader Cabrio, but my 3 year service contract would not cover the new washer. Not to my surprise, I immediately had issues with it and had to hire a repairman to assess the problem, who concluded that it was the bearings. He informed me that it would be about $700 to replace the bearings and cheaper to just buy a new machine. I called Whirlpool and explained to them about all my issues, now becoming almost comical. They arranged for an outside contractor to assess it. After confirming that the bearing were bad they replaced them. Another few months go by before problems occur, this time the washing machine stopped draining water and spinning. The service company was out another 4 times. They replaced things like the mother board and control panel. My last appointment was today, where the service guy said, There is only one error code. It is a stuck button. I said, Will you at least witness a full cycle so I can show you all my problems: clothes still dirty and stinky, items still wet after spin cycle, cycle taking 2 to 3 hours to run, horrible noises, and timer adding minutes to original cycle. He called Whirlpool because he genuinely felt sorry for my situation. They were of no help. He didnt stay to witness a cycle. Moral of story: if the error code doesnt detect a problem, the consumer will not be helped (this is something that consumers do not have access to). They will happily call a technician out to put a bandaid on an issue until your warranty runs out. I have had between 7 to 10 service calls out to my house, requiring me to take either an entire or 1/2 day off of work each time. If I added up all time lost at work, I could have easily purchased a top-of-the-line washer/dryer duo and been done with all this Whirlpool foolishness. Do yourself a favor, stay away from this product.

A little over one year ago, I bought this model from Lowes. Shortly after installation, the ceramic coating on the floor of the bottom oven cracked and shattered. I contacted Lowes... No help whatsoever. I then fought with Whirlpool for weeks until they agreed to replace the unit. Seven months later, the floor of the bottom oven, once again, cracked and shattered. I am now in another dogfight with Whirlpool. This appliance is garbage and Whirlpool does not stand by their product. Do not buy any Double Ovens from Whirlpool. My next step is to organize a class action lawsuit.

Whirlpool Gold Fridge Model GR2SHWXP002 purchased on August 15, 2007 for $1,368.77. Only repair issue so far was water leaking from the Water Inlet Valve Item # 949403. I bought a new part on Aug 8, 2011 for $73.45 and replaced it myself. The plastics on the fridge door have yellowed. No smoking in the house so not sure why the plastic has changed colour??? Would I buy one again?? Yes I love the water through the door feature and the automatic ice maker. 10 years old now and no major problems.

Our first Whirlpool washer barely lasted 1 1/2 years. They replaced it with another one that broke within 9 months. When it worked, it was great... When it didnt, it either overflowed or did not wring clothes tightly on the second rinse.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

First off, took five weeks to get the damned thing delivered after buying it at Lowes Home Improvement. Have problems with the drain overflowing when the washer tries to empty. Major plumbing work to rectify that. My complaint with Whirlpool is the washer doesnt work. It will partially fill and then stops. The wash light then lights up and nothing happens. I let it sit for three hours and the clothes never washed. It took an act of God to get the washer to empty. It never did spin the clothes. The washer refuses to work through the cycles. $1500 wasted on this POS! Trying to get an appointment scheduled is equally frustrating on Whirlpools website. Never again will I buy Whirlpool!

Very unreliable oven. Oven temperature never seems to get to the proper setting. Do not buy any Whirlpool appliance. They do not stand behind their product. A stove should be relatively simple but Whirlpool managed to produce a product that is complicated & unreliable.

Bought a nice house in 2012 which has a Quiet Partner 3 Dishwasher. About twice a week it has to be reset pressing buttons because it blinks at you when you press start. Control board was replaced a couple times since we bought house. We just put up with it. The tub has a manufacturers defect in bottom where the plastic is so thin it finally cracked and over time water trickling out went to wall. Then ruined an area in finished basement ceiling. Ive used a couple different things to stop the leak but it always starts leaking. Customer service says its not under warranty so will buy a new dishwasher. But not Whirlpool or Maytag. Same company now. Dishwasher is a total piece of crap.

I purchased a Duet Front Loading Washer (model WFW9750) in May 2010. In September 2011, the noise level had become intolerable. I called a local service company. They advised me that the main bearing was bad. It would cost more to repair than what it was worth. I contacted Whirlpool. They could not do anything unless the machine was inspected by one of their authorized service companies, which they scheduled. Two weeks later, A&E Factory Service arrived and confirmed that the bearing is bad and the cost to repair will be $1,542.06. Whirlpool customer service transferred me all over the country to tell me that the machine was out of warranty and there was nothing they could do.

Purchased a Whirpool fridge 1 1/12 - after Sandy, used for about 1 month. Now ready to move home and was told ice maker bad?? Thank god we purchased warranty! I want to know why ice maker is bad regardless covered?

I bought a Whirlpool refrigerator model GSF26C5EXW02 from Lowes. It is a huge piece of crap that has had so many visits from the Royal Appliance guy, that we are now on a first name basis. Lowes was awesome and has actually replaced this junker twice at no cost to me and has, in fact, reimbursed me for all the food this fridge has ruined by freezing. The appliance repair guy cant seem to find a problem so I just keep getting ruined food because of this hunk of junk.

First, I was put on hold by the first female for 44 minutes, and then a second woman finally answered, and said she didnt know why she would send me to her, because she was in the sales department, and she put me on hold for another 25 minutes. I finally had to go, because I had an appointment. When I got home, I called back, and got a man by the name of John, and at least he recommended he could schedule a repairman. The problem I told him is, the inside wall of my refrigerator has 2 cracks on the side, and a crack on the back wall. I dont want a repairman to come, just to tell me he cant put 2 new walls inside of my refrigerator. I could not find an email, so I could email Whirlpool about this problem, and definitely, they were of no help. I bought the refrigerator at Lowes late 2003. I have never, in my life, seen the inside walls of a fridge do this. I spent a lot of money for this, for it to crack on the inside walls. It does not seem like something is right with this.

On 16 March, I lodged the complaint to Whirlpool’s service center in New Delhi. My service request number is **. Engineer’s name is Dharmesh. He came for the first visit and he sent the person named Hassan who said there is gas leakage problem. I told him that problem is much more complex than leakage as I have already checked about the leakage, but he didnt listen and repaired and took Rs 2995 from me by giving 3 months warranty. The fridge again got damaged. Now, when I talked to Ms. **, she said the compressor is damaged and it will take Rs 2000 more, which means my earlier Rs 2995 has gone into vain and they are demanding Rs 2000 more, though it is in warranty. When I asked her that I want to talk to a senior manger, she rudely talked and refused. I called Whirlpool’s customer care on 01160008558. There’s a guy named ** who abused me and behaved rudely with me. The customer care executive doesn’t even have bit of manners as how to talk to the customers. It’s really a shameful thing which I had not even expected from the brand company like Whirlpool. I want very strict action to be taken against Ms. **, Mr. ** (CCE). I also want my fridge to be repaired as soon as possible without a single penny or I want my earlier Rs 2995 back.

After 6 years, Our $2500 Whirlpool refrigerator stopped cooling and would not dispense ice. Since we had purchased a Whirlpool extended warranty, a Whirlpool authorized technician replaced the compressor and informed Whirlpool it also required a new door that included an ice dispenser. A door was not available so Whirlpool refused additional repair and refunded the $400 purchase price of the warranty. Meanwhile the refrigerator stopped cooling again and Whirlpool refused any additional obligation. The refrigerator was now non-functional and we had to spend $3500 to get a comparable refrigerator. The moral: 1) Whirlpool makes very expensive refrigerators that have about 30% of the life-span compared to earlier vintage refrigerators. 2) They know this and will promptly refuse to warrant their product if it is to their benefit. Shame on you Whirlpool for using your corporate leverage and shady business practices to manipulate your customers.

I purchased this washer about 3 years ago to replace a dishwasher which lasted 20 years. Within a year the racks began to rot, the front panel plastic started to peel off. Within two years half of the racks rods completely rotted away. 3 years later the washer is busted - most likely pump which was probably blocked by one of the pieces of the rack rods. I am replacing it with Bosch - German engineering. Needless to say I will NEVER buy a Whirlpool - formerly reputable company again. Good-riddance Whirlpool.

We bought a new Whirlpool dishwasher with a kitchen reno. It cost over $1000. One month out of warranty the pump died. As this is apparently a common thing with these dishwashers the company sent a new pump, free of charge, but we still had to pay $150 for the install. Now, less than 2 years after purchase, the dishwasher refuses to drain. I wrote to the company, they are not interested. Dont buy Whirlpool, you are only throwing money away.

I just purchased a brand new home. I have an electric wall oven with the microwave over the oven. They are both built into the wall. Can anyone tell me why a massive amount of steam is coming out. It is really bad it makes my microwave glass so bad I can see through it. It is also making my cabinets so wet I have to use a towel to dry them. Plus I got a steam burn. Can someone tell me if this is normal.

We purchased the washing machine on February 2, 2013 and initially noticed that some of the clothes were still dry when the complete load was over. Meaning that I am not saving water cost because I then have to rewash the clothes and pre-scrub the clothes. Then a little over a year later, the machine is making this extremely loud piercing noise when spinning. The cost to replace the part is $250.00+ the repairmans fee. Whirlpool says there is nothing they will do. From reading the other reviews, this is really sad because of the numerous people having the same issueS with a capital S. I definitely would support a class action suit.

We had to have a sensor switch installed. We purchased this washer, plus the matching dryer June 10, 2010. This was just 16 months ago today.The cost of this repair was $160.24, for part labor and service call. The service call was excellent. Wish I could say the same for washer.We had previously owned a KitchenAid washer for over 20 years (before purchasing Whirlpool washer) and did not have to have one repair on it. Very doubtful I will purchase another Whirlpool.Looks like quality is a thing of the past.

My dishwasher was only 18 months old when the rack adjuster broke causing the top rack to collapse. I researched and was able to order the replacement part which now comes only in metal. (The original Whirlpool piece was cheap plastic.) I spent $40 for the new part and spent several hours installing it without any help from Whirlpool. Then when I tried to use my dishwasher it wouldn’t run. Repair person came out and diagnosed it with a pump assembly failure. Part alone was $222 and it was on back order. Extremely disappointed. I have tried to contact Whirlpool to see if they would at least offer me a discount on the part. Their customer service number is never available. On hold for so long I finally gave up. Maybe I just got a lemon but I will not go with any Whirlpool product again.

We bought our dishwasher April 2018. This morning I noticed the paint had bubbled above the heat vent (area 3x 1/2). Upon closer inspection, the the paint was also peeling. We called the company to see if they would replace the skin but the agent said the only thing they could do was send us touch-up paint. The door is considered cosmetic & only covered for 30 days. If we wanted to replace the door panel, we were welcome to buy one from them. However as this seems to be a manufacturing defect, we would be replacing the door every 16 months. When we realized whirlpool wouldnt back their product, my husband looked a little closer to see what needed to be done & found that it had rusted under the paint & painting on top of rust will adhere properly.

Whirlpool Clothes Washer Model WTW4930XW1 - We have experienced tub overfilling on (2) separate occasions with this washer model in a period of time of less than (2) years. Through extended warranty service purchased, a technician came out the first time; declared nothing explainable to cause the malfunction, re-calibrated the control panel, and off he went. This second event occurred much the same as the first; happened to walk in to notice water on laundry room floor and witnessed overflow out the lid on top. We have carefully washed additional loads after this second event without a similar malfunction. From my online research, this sure sounds like a faulty pressure switch not sensing high water level in the tub. Any other thoughts?

We purchased a Whirlpool oven a year and a half ago. Today the interior glass exploded while cooking frozen French fries. Whirlpool customer service indicates that this is unusual. Whirlpool indicated that the only way they will repair it is if we pay $375. We declined to pay an additional cost for this product which failed to function safely. In a quick Google search, it appears that the oven glass fails more frequently than represented by Whirlpool. We are disappointed in this product and the companys customer support and lack willingness to correct a product safety issue.

Ive had this dishwasher for 1 yr and 4 months. Its been used properly and kept clean. The motor quit. A dishwasher that only lasted a little over a year. Cheap piece of junk. I spent over $800.00 with installation. I will never buy a Whirlpool dishwasher again. Try and call Whirlpool and someone in India will politely read from a manual and waste your time. Useless!!!

After reading all of these reviews, Im not surprised at the negative comments. My husband and I owned a Whirlpool washer and dryer for 25 years prior to them both dying the same summer four years ago. I absolutely would not purchase anything but another set of Whirlpool washer and dryer because of the longevity of our previous set.We bought the Cabrio set 4 years ago this summer. After two years, we discovered it had a slow leak at the back hot water valve and underneath it somewhere when it spun and it had slowly leaked under the wall into our living room which eventually caused our hardwood floors to buckle. We had to replace the flooring in that section at a cost I will not even say and had a repairman come out and fix the lid lock, leak where for some reason there wasnt a washer in the valve area, underneath and the problem with the spin cycle. This was at a cost of around $200.00. Of course our one year warranty had run out. The next year it did the SAME THING AGAIN!!! Although we caught it quicker, we STILL had to replace a small section of hardwood flooring and have the machine repaired yet again at the tune of approximately $200.00. Now, as I type, our machine has yet again flooded our laundry room one year later and I will have to call a repairman in the morning yet again! Its becoming an annual and costly thing!!!I came across this site while looking to see if by chance this machine had been recalled and we would be able to get another one at no cost since we have already paid a fortune for the errors it has caused. I will be reporting to the Better Business Bureau and writing YET ANOTHER letter to the Whirlpool company with the hopes that they will recall this machine!! If enough people protest and report this shoddy workmanship, maybe they will!!!

I lodged a complaint of Microwave problem on 05/11/2011, and up to this date (18/11/2011), I am still waiting for the problem to be solved. I have a 1 year old baby. We cook food for him in it. Due to the microwave not working, he is suffering.

Cabrio Washing Machine - I purchased my washer and dryer in May of 2008. I had problems with sheets, towels and pants getting very twisted and tangled, but I just attributed that to a design flaw. My problems really began in January 2013 when loads were not level all the time. It didnt matter if it were 1 shirt or a load of towels; you had to stand by the machine and it took forever to finish a cycle.On 1/11/13, the first repair was the rods that kept the drum stable. $260.82 later, it worked again. On 2/16/13, the washer quit working. On 2/18/13, the repairman was back out. It needed a lid lock switch. It was $87.14 that time and he would be back when the part arrives ... There was still no washing machine. On 2/21/13, he returned with the lid switch and replaced it. That was $178.04 but wait, there were still other error codes so there was no working machine.I refuse to pay anymore as I now fear I will be buying a new machine after spending over $500 in less than 6 weeks, but Whirlpool did the right thing when I called and they agreed to repair the machine. They wanted a different company to come diagnose the problem (the machine gave an F50 and F51 error code to the repairman here on the 21st), so I have to wait for another repairman to come and look at the same codes flashing on the LED readout.On 3/1/13, the A&E repairman that Whirlpool sent out arrived at my house. I have been without a washer since the 16th of February. He diagnosed the problem and said that it is a $1,000 repair! I called Whirlpool and asked for a new machine, instead of throwing more money at this one. They informed me that if I didnt like their offer, they wont do anything then. I agreed to the repair.Parts started arriving at my house. On 3/13/13, another A&E repairman came out and started to fix the machine. He informed me that there was more wrong than the first guy thought, but he had the circuit boards so he would get it going. On 3/24/13, the washer quit working again and was flashing an F51 error code. This is the biggest piece of junk I have owned in my life. I have missed 5 half days of work since January and there is no end in sight. Why is Whirlpool allowed to get away with such an inferior machine?

We bought a Whirlpool Gold Refrigerator from Lowes just over two years ago and have had trouble with it starting a year and a half later. It kept freezing up and the top refrigerator compartment wouldnt get cold. We had to defrost it every three months. Now it doesnt even work. This expensive unit is less than two and a half years old and Whirlpool expects us to pay for the repairs. What happened to the days when a refrigerator would last 30 years? I hate to say it but be smart and buy Japanese. At least they take pride in what they make.

Bought a built in oven August 30, 2018. Oven stopped heating two weeks before Thanksgiving. Repairman fixed it. It is not working again, two weeks later. Bought from Best Buy. They will not take it back. Whirlpool will not replace it. UGH!!! $ 1,600 down the drain. Will no one help?

I really enjoy the self cleaning option on this unit. It really cleans everything without chemicals and then you just vacuum up the dust. My dislike is the ceramic top though. The top scratches really easily and hard to clean up spills during cooking. Overall I would give this stove a b rating.

We purchased our Consumer Reports rated #1 best washer, seven yrs. ago with a five-yr warranty. We have had nothing but repair after repair starting in the first year. The mother board replaced twice, the entire inside had been replaced within four years. It is only a household of three, the washer looks like new! The machine is now making a noise like a freight train... We had a repairman out $95.00 just to look at it! Cost of repair $1,116.21!!!! More than what the machine is worth. The replacement parts wore out in the last 2.5 yrs, again poor design. I contacted Whirlpool during the last repair issue and demanded a full replacement. The customer service rep, as RUDE as can be, checked with her higher-ups and said they would replace it for $845.00!!! WHAT A JOKE. I could buy a new one for that! The repair person said they are one of the highest repair units and the most costly out of warranty. He had one with the same issue just two days prior. I will never buy another Whirlpool product or purchase from H&H Gregg. They sold our warranty twice losing all of our repair records! It looks like I had an extra load size dumped on me!

I ordered a washer dryer combination through Whirlpool. I was given a delivery date 2 weeks out. Whirlpool employees must be doing their laundry very sparingly if they think that this would not put a strain on a household. But I was willing to wait. I asked the date and they wouldnt give it to me. A week later they called with the date and I asked the time. Again they wouldnt give it to me. However they said they would give me the time the night before. They then called with the time, which was during work hours. I told them I would be unable to do this during work hours and they gave me the only other optional date, also during work hours. I finally agreed and took a 1/2 personal day. When I arrived home. I received a phone call from Whirlpool that they will not be delivering my washer/dryer unit at all and to pick a different date. I canceled altogether.UPDATED ON 02/24/2016: I have worked hard to not get upset at companies. However I feel that this is an especially poor company and I cant remain silent anymore. I bought a Duet Washer and dryer over the phone with Whirlpool. It took 3.5 weeks for it to get delivered because Whirlpool kept cancelling. Each time, I took a 1/2 personal day so that I could meet the delivery people within their 4-hour window frame. On the 3rd attempt, they were finally delivered and set up by the delivery men.During the 2nd time I ever used the product, it stopped working, making a horrible grinding noise. I had to unplug the machine. My husband came home and hes pretty handy. However he was unable to even press 1 button. I had a friend in the repair business come the next day and he was unable to repair it. I called Whirlpool again and they said theyd have a repairman out the next day. They outsourced the job to a local company and Whirlpool sent me a confirmation email with a time and date. Again I took a 1/2 personal day. After hearing from no one, I called the repair company. They said they had no record of me in the system. I cried.I called Whirlpool and was put on hold for 3 hours. I hung up and called again. They said my department closed 8 minutes ago and they couldnt take my call. I asked how that could happen considering you began the call 3 hours before that time and would have stayed on hold until I died had I not decided to hang up and try again. Every time previous to this I had been on hold for a minimum of 1 hour.I have been trying to return the product. They tell me that Im unable to because my product is functional. I told them it was in fact not functional, which was about the 3rd time I said this, and they said Ill have to call back 1st thing in the morning. I told them I cant risk any more work time to deal with this poor company. So they put me on hold again and thats where I remain. I am currently going on 27 minutes.

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

Whirlpool side by side with in door ice maker W10281961D - I purchased the refrigerator 10-2013. Within 9 months all of the food in the refrigerator side was freezing. Unfortunately, I did not purchase the extended warranty so I would turn up the temp control every 24 hours as suggested in the manual. The water maker then stopped working. I am disabled and money is tight, but I was wasting so much by throwing frozen produce and eggs away and was worried about thawing meat on the counter since it was not possible to in the refrigerator.I finally broke down, called Sears, purchased the warranty at that time, which was $259.00 and when the repairman came out we found out the damper was broken, thus causing the food in the refrigerator to freeze and the motherboard had went out, thus causing the temp controls not to work. The extended warranty had a $500 max, so we had to pay an additional $120.00 out of pocket. It is working fine now, but in my opinion, it should not have stopped working as quickly as it did since it was an expensive purchase to start out with.

My refrigerator is a side by side and its freezer compartment is small (width). Whirlpool is always my brand of choice for household appliances. I personally would not choose the side by side design again but I would choose Whirlpool.

Our $2000+ Whirlpool Gold just had the control board fail. After calling Whirlpool, local services and all national parts suppliers we were told each time the part is on back order until June. If this is Whirlpools way of generating new fridge sales, it does not work. No Whirlpool, Kenmore, Frigidaire or KitchenAid, all made by the same company will ever enter my home. The control board runs the fridge. Which executive thinks a family can live without a fridge for 4 months? What terrible service. GE always has parts and service. Go with GE everyone.

I bought the Whirlpool French 4 door fridge WRX988SIBM 01. I like the way it stores and layout (other than the icemaker taking the entire left door out). But I got a lemon, I bought the Lowes 5 year warranty (with the 4 repairs replacement). The fourth repair and dead declaration was 5 years and a week (so just out of Lowes extended warranty by a week). The Death Certificate repair guy said they dont make em like they used to. So I am now buying another fridge - trying Samsung this time. Every fridge has a lemon once in awhile and with my luck... Well you can thank me for taking it off your hands! :) I am averaging 5 years per fridge. Thats a lot of money and I expect to get at least 10 years life on a major appliance.

Refrigerator door display cable failed. The company declared refrigerator is beyond repair. Cable must be replaceable, we cannot throw refrigerator for small fault. The cost of cable is hardly Rs. 200 and refrigerator cost is Rs 25000. It is a design fault. Company has to replace cable.

The salesperson was great but we are not happy with our washer. We already had it swapped out once because of white spots showing up on our clothes. The only thing they could think of was that the bleach I used wasnt rinsing out completely so it showed up on our clothes. Recently, I washed a table runner by itself and it had some red in it. Now there are red spots on a couple of items that I washed after the runner. My husband just now asked why there were red spots on a shirt that he wears all the time. I explained. Also, we have had some white spots on clothes and I could scratch it out without leaving a permanent mark. Were no longer using bleach and we use only liquid detergent and all of it is HE. So I dont understand the machine. I hate it.

I bought a house and for the first time in my life, I was able to afford and buy all new Whirlpool appliances at Sears. I worked so hard all my life and was so happy I could get new appliances when I was almost 50 years old. Up until then, I could only afford to get used appliances. Even then I had to finance them with a credit card, only to be so sad and disappointed. They are without a doubt the ** junk I have ever had. I wish I could have all my old appliances back. My new Whirlpool flat top oven burns everything and has ruined all my pots and pans. I do canning every year and it has ruined my very old and heavy pressure cookers. Even when you turn the heat all the way to low, it burns everything. I called the manufacturer and they say they do not have to disclose that it will ruin your pressure cookers or burn everything. I am very angry I bought any Whirlpool appliances. I also got a new washer and dryer; they are junk too. They dont clean my clothes like my old washer and everything is so wrinkled up when it comes out of the dryer. I need to iron everything. I have never seen anything like it. I also bought a Whirlpool hot water tank that has now gone out 2 times in 5 years because the thermostat burns out. I pray it doesnt burn my house down one of these days. One of the times it went out, I was about 10 feet away from it and it literally blew up and about gave me a heart attack. It was so loud and scared the bejezzers out of me. Whirlpool, you suck. I have told everyone I can tell how much junk your appliances are. Your company should have to be accountable for selling people such **! I would sure like to be paid not only for the cost of these junky appliances but also all my quality pressure cookers, ruined clothes and distress this has caused me. They have no consequences. They have gotten away with ripping people off and giving a lot of us tons of stress, stress, stress, and anxiety, not to mention all the financial cost. Thanks, Whirlpool, you piece of junk! I think if I had not worked so hard to finally get what I thought at the time were high quality new appliances, I wouldnt be so affected but I dont have the money now to get new quality appliances. Whirlpool took my hard earned money for their junk.

I bought a new home from DR Horton with Whirlpool appliances. All of the kitchen appliances were Whirlpool which came with a 1 year warranty. After closing on the house and getting in, started the dishwasher for the first time, it started leaking water instantly from the bottom of the unit and spilled all over the floor. Tried to contact the builder/inspector who asked us to contact Whirlpool. Called Whirlpool and I was kept on hold for over an hour before someone answered. The rep was so adamant talking all unrelated things and said that she cannot do anything for another 15 days. After escalating to the supervisor, it was the same response. The service at customer care is so bad with no fix in sight. I am not sure what they are going to do with the appliance and not sure whether they come and fix it or keep me waiting. Very unethical, the way they talk to the customers.

Whirlpool stove, product ID WFG540HOES. I purchased a whirlpool gas stove in 2014 for a lake house. Came to my lake house to find the temperature was 90 degrees inside and the oven was running full blast. The oven had turned itself on. Whirlpool appears to be having a problem with this type of issue. Called their customer care department and was transferred to the appliance safety line which was only a line to leave a voicemail. Very bad customer service. My kitchen countertops and kitchen floor will need to be replaced, also cannot get rid of the burnt smell in my house. Do not recommend purchasing Whirlpool appliances.

Quiet Partner II - Our dishwasher racks started to crack and rust very quickly, about two years after purchase. We repaired the racks and tines, but the rust got worse. We replaced our dishwasher today with another brand. Many of the tines on the drying rack had rusted and broken off. We have been told to only purchase Nylon racks. I hope this is good advice. I must admit I had no trouble with the machine as far as cleaning my dishes. I just felt the racks should last longer than two years. Cost to replace racks was about the same as replacing the whole machine.

This product is unsafe and should be recalled. It has aluminium wires that connect the unit to the 220 Vol Power source. Aluminium and copper wire dont mix. I took a shower and was getting ready to leave for the day when I went into my garage to smell burning plastic and wires. I traced it to the hot water heater and discovered the wires in the Energy Smart were melted and burned. I checked with Two Electricians who told me that the wires in the unit can not handle the high heat and melt. If you have one get rid of it. Had I left for the day I would have lost my home, cars and pets. If anyone would like to see this unit I still have it and photos.

I feel the Whirlpool washer we have Works amazing. Its an older model and Im still happy with it. It does big loads without having to do it over again or on balancing itself. I have actually had a Samsung washer and we constantly had issues with it - sensor problems and was not very user-friendly at times. I also feel that a lot of the newer washers out there are cheaply made plastic parts and can break easily. Too many companies cutting Corners these days.

This is a comment for the person with the ice maker problem. I have a side-by-side, in-door ice dispenser that clogs up. First sign of problem is either the ice wont come out or it comes out crushed. What happens is frost builds up in the path the ice takes at a couple of different points. The only solution I have found is as soon as the problem starts I turn off the ice maker using the switch on the inside of the freezer. Then let it empty with normal use (if you wait too long youve increased your problems). The release button for the ice bin has frozen by now so you cant just lift it out. The bin needs to be empty. When it is empty, work the bin loose and take it out. Youll find that frost and maybe cubes have collected, frozen and blocked the passage. Be sure to turn the ice bin on its side and spray water into the undercarriage to melt and remove all the ice build up there. I use a hot sponge to melt the frost in the ice tube and then dry everything. This gets messy so be prepared to have water on the floor. Dry the ice bin and reinstall it. Ice cubes will be ready to drop from the ice maker so it wont be long until you have plenty. I live in Florida with high humidity so need to go through this process about once a month. Its a pain, but now it is just part of owning this unit. Good luck and hope this helps.

I have not had any problems with my Whirlpool refrigerator. It is four years old and has had two owners, including myself. It has the stainless steel look and has top to bottom french doors, one side is the freezer and the other the refrigerator. Both sides are equally the same size. It has a filtered water dispenser and ice maker in the door. Id say for the price it is a really good value.

Note that most of the complaints are about gas water heaters, but the electric water heaters dont seem to be much better. Mine, barely made 4 yrs old and both elements and thermostat went. Had plumbers in for estimates in to repair - much cheaper to install a new one (No...not a Whirlpool!). Very disappointed in the product.

Bought this refrigerator in 2018 and ice maker went out 2x, then compressor went out and waited 4 weeks for part. Now the refrigerator is broken again and not cooling. Dozens of other reviews indicate the same issue with this model. It’s clearly a defective model. Customer service in Tennessee are very friendly but my refrigerator is still not working. Whirlpool French door - wrf954cihm.

Most of my appliances are Whirlpool - dishwasher, refrigerator, clothed dryer and the Cabrio washer. The washer before this one, I had it for over 10 years and replaced it because of rust (thats another problem with Whirlpool - rust). Now the Cabrio hasnt got all kinds of problems - UL, F1 and jumping. The serviceman asked me for $450 for repair; it included a set of springs for the drum, a new electronic board and a 30-day warranty on parts and labor. Im better off buying a new one (I cant afford at this moment). My wife is scared of the darn thing and refuse to use it so now I have the job of washing and standing guard to make sure the washer doesnt leave the garage. Thank you, Whirlpool - and my refrigerator works fine all rusted.

WTW5640X The machine is tearing up clothes of many including mine. I gave them the benefit of the doubt and thought I had over-loaded the machine. Not so. There has been nothing run through the machine other than clothes and bedding. When I called for service 1 1/2 months after warranty is out of date I am told I can have a service call including parts and labor and another year warranty for almost $400. If it werent for the numerous reports online of the machine doing the same to others I might have gone for it. Shame on you Whirlpool. Are you the next GM?

I have bought what I thought my dream washer and would never need to buy another one. I told people about it and could have sold many of them. That was in my first year. Now I am into our second year with them and it quits. It cost right at 500.00 and when I called Sears, the company I bought it from, they charged me a service call and says it will be $585.00 to fix. WHAT? This is a lemon. If I were to buy a car and have this sort of problem they would warranty it. Why not appliances? This is an outrage. This should be illegal to sell.

Not as big as appearance would indicate. Very disappointed in actual usable space. You have to open both doors to get anything but the smallest items out. Had unit for less than a year and had to get freezer door seal replaced. Glad we got the extended warranty.

Right from the start of buying a new suite of Whirlpool appliances, the light over the range burnt out. We figured it was just a bad bulb so we replaced it. Soon it burnt out again, replaced it again, then again it burnt out. I finally called Whirlpool about the problem and found out it is the electronic panel that needs to be replaced... Of course at a full charge to me! I am so over WhirlPoo, (yes I spelled it that way on purpose) every single appliance has had issues. I have just lived without a light over my range because fixing it is more expensive than buying a whole new microwave. Never again will I buy any WhirlPoo appliance!

I bought a Whirlpool washer WTW4800XQ top loader. I have owned it for about two years and now it has tore up, the repair bill will cost almost what I paid for the washer. I feel it is bad business to sale something and it not last any longer than it has. No one should have to buy a washer every two years!!!! When it gets to the spin cycle it works fine and then all of a sudden it will beat and bang and if you dont get it stopped it will be in the middle of the floor. Im very upset and put out with Whirlpool!!!!

My glass stove top broke for the second time. The first time Whirlpool accused me of dropping something on it and chipping it. I didnt but paid the $400 glass replacement. Today while cooking, I put cold from the fridge not freezer, sausage into a warming fry pan. I heard the same pop I heard 2 years previously...sure enough the glass stove top broke. After a phone call to whirlpool, and hearing they were sorry but theres nothing they can do, I will write as many letters I can so others dont buy whirlpool.

Purchased microwave 7/3/2016 & paid for installation on 7/9/16. Product started malfunctioned in December. Technician came out 12/30/16 and as of today we still do NOT have microwave. Whirlpool claims they issued credit for microwave & installation. But somehow between safety department & vendor relations with hhgregg they want us to pay AGAIN for installation & haul away on a defective microwave. Hhgregg vendor relations & Whirlpool pointing fingers at each other, we are still without a paid in full microwave. No one cares, and we have been treated poorly by both Whirlpool & hhgregg. Its 3 months without a microwave and Whirlpool doesnt seem to care one bit. Worst customer service Ive ever received.

Ive never considered writing a complaint before, but feel it is necessary in this situation. I have had my Whirlpool refrigerator since November, 2007. It has worked great until this past April when the freezer began to overfreeze, cause frost and ice to build up. I have had Whirlpool Factory Service out to repair the unit twice a month since April with still no resolution and the appointments are getting harder and harder to get someone to come out in a timely fashion. I called on September 1st and the closet appointment is September 15th. They werent even able to book the appointment when I called. I was told someone would call back within 3/4 days. When I didnt hear back today, I called to find out an appointment was set.Ive called the Resolution Team to obtain back records of service but havent been successful in receiving a phone call or email. I havent received all of the follow up emails after service which is frustrating since there have been two technicians that have come out for repair and were not provided any history on the unit. If I had the follow up emails, I would be able to share that information with them.I contacted Customer Service to find out what I can do in regards to the issue I am having and was told its best to stay with the service provider that I began with since they are familiar with the issue. I would imagine if they are familiar with the issue that it should have been fixed by now. Ive also sent a response card back to Whirlpool Home Appliances at the Survey Response Center and havent heard anything from them either. When I called to follow up there wasnt anyone that could point me in the right direction to obtain answers. They were able to provide me with the mailing address for Consumer Affairs though. Ive been told numerous times that if it gets to a point it costs too much to fix they will replace the unit. Im not sure when that decision is made. I have an extended contract and will extend it again in October when it expires. I just want the unit fixed or replaced. Its been since April with the same issue. Very disappointed consumer.

I have had this range since 2008 and used the self-clean last week. (I dont use the oven that often) Since the clean it has not heated up to required temp. I just called Whirlpool and a tech is coming out this Friday (Nov. 15th 2013). If it is determined to be the self-clean that did in fact cause this, the tech calls for an authorization and the repair is covered by Whirlpool. I will report back what happens.

In 2011, I bought in Croatia, for the start, 2 washers (model 3LCHW9100WQ) and 1 dryer (model 3LCED9100WQ) and opened the first self-service laundry in Pula, Croatia. Since the beginning, I had problems with the gum (black). After the washing cycles, you could see black lines on the laundry. Whirlpool Croatia denied that the gum can be the cause. After two months, they gave me new gums, but the problem still exists. After 5 months of work, the first malfunction on the washers started. The biggest problem is that it took and still takes them up to a month to repair them. And these problems I have ever since. Also, the error codes never showed the correct malfunction code. In global, if I take that I have these washers and dryer for about a year, they were out of function for more than 3 months. The warranty expired in April 2012. On these reasons, I cannot recommend any product of Whirlpool, and I have to change to another company to buy more washers and dryers.

Multiple issues with the Gold Series. Have lost two refrigerators full of food!!! First problem was ice on the back wall of the fridge. 2 years later refrigerator is not blowing cold air and it is only 4 years old!!! Terrible product!!

In April of 2009, I bought a Whirlpool over the range microwave, model # MH2175XSB-5. In September 2011, a small piece of the door fell off at the hinge. Pieces have continuously fallen off and now the door is splitting, rendering the item useless. It was purchased at Lowes and I had them installed the item. Two years of service plus installation come to big bucks for a piece of trash.

Whirlpool Gold Class Refrigerator is not quiet 4 years old. Starting at about a year old, I had to start defrosting the freezer periodically because the freezer coil would build up ice to the point where the fan would start rubbing on the ice and making a loud noise. Then about a year ago, it started leaking water from somewhere around the water filter. The water damaged my cabinets and flooring. Then the freezer slowly started to warm up. I had a technician look at it and he determined the compressor is bad. That would cost about $900 to fix, according to him. I thought it had a 5 year warranty on the compressor and associated parts. Whirlpool is claiming this is not true. The repair costs will not be covered. I paid almost $3,000 for this refrigerator! Didnt last 4 years and caused thousands of dollars in damage to my cabinets and flooring! I will never buy another Whirlpool appliance! Buyers beware. Stay away from Whirlpool at all costs!

After being a faithful Whirlpool consumer for years... I no longer have any faith. I purchased an entire kitchen suite. The side by side refrigerator Nov 2013. The first refrigerator was delivered with the side cabinet deeply dented in several areas. Another was delivered 4 weeks later. Silly me... I thought, Okay, no big deal... what could go wrong? I didnt take time off work again to receive the replacement. My son took delivery (never looked at it). I get home... the front of both doors looked like they had been kicked in all the way across! To add, the cabinet sides were textured (not smooth like what I ordered) and the door handles didnt match the other appliances. So, I called HDepot & called Whirlpool (only to be on the phone an hour each time due to high call volume. Imagine?). Then Whirlpool reps are talking to me like I am some sort of idiot... saying that the refrigerator was EXACTLY the same... not possible that the handles or sides were different!!! Because it was damaged (and I mean ridiculous! ) another 8 weeks for a replacement. Frig #3 arrives and I take time off to receive it. Ah, the right refrigerator... but again ~ handles dont match. Not POSSIBLE.. Ms. _ _ _ _... it is the exact refrigerator, those are the same handles. Hours and hours on the phone to HDepot and Whirlpool. Finally, HDepot rep has a WP rep at the store when I call, and bingo! Oh yes, there are two styles of the Exact same model. The handles are ordered... 10 weeks later I finally have matching handles! But, wait... gets better. The fridge has been loud from the start, CONSTANTLY running but, not cooling some areas and freezing in others. Then when you open the freezer it is like a burst of winter wonderland is unleashed in your face. There are sheaths of ice building up on the top of the inside door. Hmm, I think what is going on? The Whirlpool designated repair company comes out. Ah, well here is part of your problem. When the refrigerator was being put together they left a few thicknesses of blue packing tape between the door and the rubber seal in the freezer. The rep tried to fix it to no avail because the door was also warped. First they were going to replace the door. Waiting for another 10 weeks. Nobody calls, whats going on? Oh, never mind, or rather... that was never happening. I have spoken to many reps with Whirlpool, I have been polite with all. In turn, from most I get curt hard ball back. The offers to resolve this from Whirlpool have been ridiculous. I am sorry for my loyalty to Whirlpool, as it has not been reciprocated. I have had two more deliveries - both the wrong unit! I never thought there were others out there. What a mess. They should recall.

I bought my first Cabrio set in 2008 to replace Maytags that lasted forever but looked their age on the outside. No problem with cleaning and drying, just wanted something new. What a mistake! I looked in Consumer Report Guide to pick and found the Cabrio set. Had problems after the first 4 months - UL uneven load codes flashing up, and had to replace suspensions and bearings, boards, etc. Unfortunately within that 4 months I bought another Cabrio set to put in my vacation home. Started with the same issues and really hard to get a service technician to come out because of where we were located. Customer service with Whirlpool sucks as well as Sears service. It is AMAZING to me that Whirlpool will NOT stand behind this product. I am writing this as I see an F1 code flashing on my washer here at my second home. I have a load of towels in it and house guests arriving in the morning! I will be trashing this washer and dryer and finding something old school and reliable. I want no bells and whistles, just clean and dry clothes. Whirlpool, you should be ashamed.

I have a Whirlpool gas water heater that failed after only three years of operation. My previous water heater in the same spot lasted 18 years. The problem is a defective thermo coupler design that burns out if a filter you cant access isnt cleaned every three months.

Water pools at bottom of freezer and onto floor. Has been repaired twice, but still leaks.

I have a Whirlpool 33 inch wide Side by Side refrigerator. WRS311SDHM. This is the worst refrigerator I have ever had. Temperatures are inconsistent. It is less than a year old. Initially, I stored the big container of spring mix lettuce on the bottom shelf of the refrig as it wouldnt fit in the crisper draw. The temp setting in the refrigerator was set to ideal. Oddly though, in the freezer, ice cubes were melting and refreezing creating a massive frozen block. So, I raised the temperature in the refrigerator, but kept the freezer at coldest. However, I noticed that when I set the refrigerator to a warmer setting, ice cream became cold soup despite the coldest setting.I called Whirlpool and a service technician from Georges Appliance in New Providence, NJ came to my home (of course I had to take half a day off from work). He stuck a thermometer in the freezer and said, its working fine. While at my home he called Whirlpool who said that if lettuce isnt kept in the crisper drawer it will freeze (silly woman, dont you know that?) and ice cream will get soft in the freezer if the temp in the refridge is warmer than ideal. So, it seems I can have lettuce or ice cream, but not both. Okay, so I put the temp back to ideal, bought smaller packs of lettuce that would fit in the crisper draw and called it a day. Nope....lettuce and anything else in the crisper draw freezes too. Wilted, soggy lettuce is so nice in a salad and frozen baby carrots can break your teeth.I have been on the phone with Whirlpool executive dept several times. They offered to have another service company come out to look at the refrigerator. This repair company would not give me a 4 hr time frame until the day before the actual service call. This might be okay if you work from home or are retired, but this is not my case. I opted to not have them come. This is my last Whirlpool product. Since KitchenAid and Jenn Air are owned by Maytag/whirlpool, my other options are LG, Samsung, GE or Sub Zero.

I purchased a Whirlpool bottom freezer refrigerator for my wifes birthday because my old one was old, ugly, rusted and didnt match. Since she likes to cook, it was her dream in life to have a stainless steel refrigerator with a freezer on the bottom. At the time, it was the only kind that would fit into spot. One year ago, first the ice maker leaked causing water to spill onto the floor. Since I am a mechanical whiz I bought the part for about $30 and fixed it myself. We were happy.After two years, the freezer worked, but the refrigerator part went warm. I had a repairman replace the control box for $100. It still didnt work. We called Whirlpool, and they said the warranty expired, but as a courtesy, would charge me $95 for a service call. That was not acceptable. They told my wife that the products were man-made and are prone to mistakes. I replaced the fan myself for $100, but drove a total of two hours to get the part since it was rare. It worked great. For one and a half weeks, we were happy. Then the refrigerator and freezer DIED. Only the light and the fan worked. We bought a old school used GE top freezer, but at least it is stainless steel. We lost $2000 in two years and the people at Whirlpool refuse to do anything about it because it isnt their problem. Worst refrigerator EVER!!! !

I have been blessed with my washing machine. I have never had one problem with it. I have had my machine for over three years now. It is a reliable machine, with five different water levels from small to super. It also has three different water temperatures (just great). I am very pleased with my washing machine. I cannot tell you how many machines we looked at before selecting our Whirlpool, thank goodness we did.

We bought the microwave new after the 2011 flood where we had lost everything in Tennessee. I wanted to get Whirlpool appliances in the kitchen so all appliances were replaced. We bought a Whirlpool model WMH1163XVU-1 microwave; the unit will run but doesnt heat. I also called Whirlpool and with no regard to customer service at all even with all the complaints... This saddens me because I will never buy a Whirlpool appliance again and my grandparents only believed in them... With all the complaints, the attorney generals office should do something for the people.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

My double oven is less than 2 years old. I just used the self-cleaning feature on the bottom oven and now it wont work at all. I understand that this is a common problem with Whirlpool ovens and I will never buy another Whirlpool appliance again. What a piece of junk! I have used self-cleaning on my ovens ever since they were invented and have never had a problem before.

Mtf18 defective refrigerator - The unit is 2 yrs old and about 6 months prior to 2014 I could not keep ice in the refrigerators ice (freezer) and the appliance compressor ran 24 hrs. a day without recycling or stop. I did not purchase an extended warranty, after all, Maytag the dependable company. The lonely Maytag repairman. Right!! The unit cost $$700. and is now an anchor. You cannot repair the compressor, only replace it...

As described in many similar instances found on numerous complaint boards (including this one), Whirlpool has defective over the range microwave convection ovens (model # GMH6185XVS) with faulty magnatrons. I have had the exact same experience with a new product failing at 16 months (the first time) and within 6 months failing again. Whirlpool is not concerned about their consumers, only their money. They are more than happy to sell an extended warranty, but are not willing to work with customers that have lemon products.I tried working with Whirlpool customer support with little assistance other than to offer to sell me a $250 extended warranty. I additionally filed a complaint with the Better Business Bureau concerning Whirlpool to include over 10 pages in documentation with numerous people reporting this same complaint. Whirlpool is still not willing to acknowledge they have faulty or defective components in their product and so generously offered to pay for the replacement component (only - not the service to repair it).I spent $600 on this unit new, $163 to repair it the first time (at 16 months old) and no doubt it will cost me an additional $163 to repair it again (not even 6 months after the first repair). I am not willing to continue to throw good money after bad on a defective unit. For the cost of the repairs and their extended warranty, it is cheaper to buy a new unit from a different manufacturer.It is clear from this site (in addition to numerous others) that Whirlpool has a definite quality problem - both in products and service!

I cannot adequately express my dissatisfaction with the Cabrio washer and dryer that I purchased couple years ago. I will never buy a Whirlpool product again. That includes Maytag; Kenmore; or Amana products. I have had nothing but problems from the start. The washer sounds like jet engine taking off in the spin cycle. I found out the washer needs new tub bearings ~ $200. The washer is tearing up towels during the wash cycle not sure what the cause is.My washer will only wash clothes in certain cycles (bulk). I keep getting error codes in normal or other cycles. The washer takes long time to fill so it times out during fill cycle. I replaced fill lines and checked for blockage, everything was clear. The washer probably needs either new motherboard or water inlet valve. Not sure which, maybe both? It is impossible to wash a load of clothes without getting the UL unbalanced load indicator. I also have problems balancing the load. I have taken wet clothes out and put them back in with no luck. It takes hours for a load to finally wash.The dryer has had its problems. I just replaced the belt tensioner on the dryer because it was making a terrible screeching sound. The noise was very annoying. I am very disappointed with quality of Whirlpool products. However, don’t worry about improving customer relations because I will never buy a Whirlpool product again. P. S. How come you have not issued product recall? There are 1,000s of similar complaints concerning the Cabrio washer. Frustrated customer.

Such an expensive refrigerator but poor quality. Bought at Home Depot back in November of 2019. The bottom Freezer freezes up messing up everything only three months after purchase. I wouldn’t recommend it at all to anyone.

The space could be laid out a little better. The flimsy shelf is not real stable for foods or ice tray. Where the shelf locks into the side wall is not deep enough to stabilize the shelf itself. The flat indentations in the bottom, where they meet the front, have an edge that makes properly cleaning the freezer a bit difficult.

The oven will not turn off. When I called Whirlpool and told them what had happened they immediately put me in contact with the safety division. My question is if it is a safety issue, why is there not a recall and why do I have to pay for the circuit board. If there is a safety issue why is there not a recall.

Bought a Whirlpool Gold stainless steel refrigerator and the thermostat didnt work after a couple months of use. Lost all the product in the refrigerator and freezer and whirlpool would not compensate us. They did pay for the $29 part because it was under warranty but still think it was completely their fault for putting a defective thermostat in it. Last night the relay on the circuit breaker stopped working and I again lost all my refrigerated food overnight. This time it is not under warranty because the warranty was only good for one year. So, I just paid $314.03 to have it repaired. So angry that I spent so much money on 4 Whirlpool Gold products when I remodeled my kitchen.

I will never buy another Whirlpool again or recommend them to anyone, and discourage anyone from buying one. I bought a Cabrio washing machine just over 2 years ago and yesterday I received an F51 error code. The manual says that this code requires a technician to come a check for repairs. Well, before I do anything I google the problem, and lo and behold there are thousands of complaints about this issue with the Cabrio models. Some saying that what needed to be replaced were a control board ($280) and a rotor (unknown amount), not including the price of labor. Some said that Whirlpool knows about this problem and they covered the parts and repair. This didnt get my hopes up, but I called customer service and of course they said that there were no reported issues with the model and that what I found on the internet was probably an older model. Of course! The lady on the phone told me that they would not cover the costs and it would be anywhere from $300 to $500 depending on the route I wanted to take. That is a 1/3 to 1/2 the price I paid for the machine. This is ridiculous! I am tempted to just get rid of the washer and go with a better company that actually cares about their customers. This error code was definitely something they know is a big deal if there was nothing I could do about it other than call a technician. I paid almost $1000 for a machine that has barely lasted 2 years before I have to pay money to have it fixed. Not a company I would ever purchase anything from again!

Purchased Whirlpool dishwasher and range approximately 16 months ago. Dishwasher must stop in middle of rinse cycle because the dishes always feel filmy and there is an inch or two of water in bottom. Must be bailed out by hand. Piece of garbage. Called Whirlpool and they can get us a service man from 8-4 (who waits an entire day these days) on New Years Eve. Next appointment is following week to examine and will fix (if it is their fault and for a fee). The last two dishwashers I purchased lasted 10 and 7 years respectively. Stay away if you dont want bad equipment, uncooperative service, and aggravation. Range I bought was OK but the oven temperature is always off 10-15 degrees from what it says it is. I honestly wanted to buy American but I feel cheated. Next time Ill try Samsung and see if they give a damn.

Its now Nov 8 and Ive been officially dealing with this issue since Sept 26. This washer was installed in a new home. After less than 10 loads, my washer stopped draining and I was left with a load of towel soup for over a week while waiting for a service call. I still have the same defective non functioning washer sitting in my home and have been unable to do laundry at home in all that time. So far Ive spoken with 2 customer service representatives. The first was incapable of scheduling a service call. She clearly did not understand how to operate the database used for scheduling. I was finally able to schedule appointment on my own but had to wait a week before the technician was able to come by. It was determined that either the latch mechanism or the mother board or both are defective from the factory.The second was just plain dismissive and completely unhelpful. I sat on hold for about an hour each time before getting to speak to a person. Ive also received two canned emails in response to my poor review of this washer on the Whirlpool website. They basically blame COVID for the delays and state the parts delivery should take 3-4 weeks. I was originally told 14 working days for delivery of the parts. We are already past both deadline with no end in sight. At this point, Id like the defective washer replaced rather than repaired. And for the record, this was a new washer (less that one month old) installed in a new house that now stinks to high heaven because slimy, scummy water that will not drain out has been there since September 26. Id really just like for someone at Whirlpool to honestly care about this and take a moment to address this issue.

I feel as though they could use some additional features, it’s also hard to change out some of the wiring in the back. I’ve had some issues with smells coming from the washers as well from them. Hopefully they can start to look into tweaking smaller details to improve the overall machine.

My dishwasher interior and exterior is easy to keep clean. Very quiet and cleans all my dishes. The various cleaning options meet all of my needs. I would recommend this brand to everyone. I have had my dishwasher for 2 years and have had to call for service.

Do not buy anything Whirlpool makes. I purchased a new home and new appliances. In less than 4 years motor is gone in dishwasher. 6 weeks later I have another leak that has ruined my hardwood floors. My fridge is making all sorts of weird noises and alarm is going off. They are coming to ‘look’ tomorrow. And my washing machine is no longer draining. Whichever you buy from check how the extended warranty works... Trail Appliances Calgary uses a company that is horrific to work with, doesnt have a human to talk to and wont acknowledge you unless you pay $149 upfront. RUN AWAY!!!

I bought a Cabrio washer in 2009. I started receiving the infamous F51 code. When I called Whirlpool, they refused to even acknowledge that there is a problem with this washer. When I brought up the pages and pages of complaints about it, they acted like they did not exist. I hope this review will deter people from purchasing one of these faulty products!

Purchased this Upright freezer model 160NZTQ02 approximately 2 years ago. Freezer had problems maintaining temperature from the beginning. Noticed it freezing up at air vents in back of interior. Unplugged, removed contents, and let defrost by ambient temperature (approximately 4 hours). After using this method for first three defrost periods (approximately two weeks apart) I began defrosted with hair dryer, then moved on to heat gun. Bottom line is this junk wont hold temperature and freezes up every few days to a week. No more Whirpool for me.

Whirlpool Duet Steam Washing Machine WFW9500TW had F35/Suds code 14 months after we purchased the washer. Hose / air trap is clear and the hose from the analog pressure switch is connected properly. The appliance tech we had come out to look at the washer determined that the analog pressure switch was defective. He told us that this is a common problem with this washing machine. Whirlpool supervisor, Michael (female), stated that they could send a tech out - and charge us for the call - to diagnose the problem. She refused to transfer me to someone who could help and couldnt comprehend that the its out of warranty excuse isnt a proper defense for a product defect. There are many posts about Analog Pressure Switch problems with this washing machine.The posts about Whirlpools poor customer service are absolutely accurate. They are horrible - good luck in getting them to work with you. We read the reviews for the Whirlpool Duet Steam washing machine before purchasing one and we disregarded the bad ones as disgruntled customers. Please do not make the same mistake we made. After my conversation with their customer service dept today, I will never buy another Whirlpool product again. Defective parts happen. Refusing to fix a known problem is unacceptable.

I have been given a runaround for over a month to get my refrigerator fixed. They gave me a defected piece and it broke down in less than a year. I have been calling them up every day and they put me on hold forever-then they ask for all the details and direct me to another company. As of right now I have not received any help-My family is really frustrated as we have no fridge all this time. I dont know what to do.

I purchased my water heater at Lowes and had it installed professionally. I suspected something was not quite right on numerous occasions because the hot water recovery time seemed excessive. I finally called Whirlpool and they gave me the names and numbers of two companies that were on their list. The first asked for the model number and normal information and never called back. The second showed up spent five minutes charged me 78 dollars and said they could not get the part (gas valve) I needed. And if I could get it from Whirlpool they would charge me 250 to put it on. They also said Whirlpool made horrible water heaters and I should save myself the trouble and just replace it. I have since heard from additional plumbers and the gas company to stay away from Whirlpool. I did have the water heater replaced. When they did it and they drained the old water heater it had so much sludge in it draining it was very difficult. The sludge is mystery since I have a softener in my home and it should have prevented that. The individual from that gas company said that was just one of the many issue others had experienced with these heaters.

Whirlpool Cabrio Washing Machine F1 code - We have had this washing machine for over 6 years now, and ever since our 3 year warranty time was up, the washing machine will only stop, and display the F1 code as soon as the wash cycle has completed, with 23 minutes left. To start off, with this problem, it is causing me more water, and electricity that should not have to be wasted if the machine worked properly. I called the place where I got the machine, and was told to give Whirlpool a call. I did this, and was told that there was nothing that could be done, and if I would like to schedule an appointment for a tech to come out and work on it, they could do that. YES, I would have to pay for it. Needless to say, the washer has been doing this for over 6 years, and if there is a way to get it fixed WITHOUT having to pay for the repairs, that would be wonderful.

Our Whirlpool Duet front loader washer developed a mildew smell and started making a horrible banging noise on the spin cycle. We had a service man come out and the concrete weight had broken in half. He said this was not uncommon. I just did a Google search and apparently this is a true factory defect. Luckily we had purchased an extended warranty. I always thought Whirlpool was a premium brand but after this experience I will never buy another washer from them. They should do a product recall.

Whirlpools front load washers do not have easy access to the drain pump filter. The entire front of the machine including the door has to be taken off to access the filter. When putting washer back together the parts are cheap and screws break. Most companies that sell front load washers provide easy access to the drain pump filter. Buy one of those instead of a Whirlpool and you will save yourself a lot of time and hassle.