Purchased this Upright freezer model 160NZTQ02 approximately 2 years ago. Freezer had problems maintaining temperature from the beginning. Noticed it freezing up at air vents in back of interior. Unplugged, removed contents, and let defrost by ambient temperature (approximately 4 hours). After using this method for first three defrost periods (approximately two weeks apart) I began defrosted with hair dryer, then moved on to heat gun. Bottom line is this junk wont hold temperature and freezes up every few days to a week. No more Whirpool for me.

Aqualift technology does not work!! This is absolutely the worst product I have purchased from Whirlpool. The aqualift technology DOES not clean the oven, even if you clean the oven after EACH time you use it! I am not able to bend over and spend the afternoon in the oven. And even when I do, I cannot get this oven clean!!! Please DO NOT buy a Whirlpool stove with an aqualift technology oven cleaning process!!! You WILL be sorry!!!

Whirlpool sent me a different part 3 times and hot water tank only work for a few weeks, then the pilot light goes back out. They never offered any more help.

Weve had this washing machine only a few years, and our household of 2 probably averages 1 load of laundry per week. Weve always had the same problem everyone has with the detergent stains on clothing and having to rewash loads, and the only remedy weve found was using the oversized loads setting and rewashing a load. The last straw was 6 months ago. It quit going through a complete cycle and would not spin out without resetting it. Then it quit spinning out at all. Service Guard, a 3rd party warranty company, diagnosed a faulty motor and ordered a replacement. After a long delay Whirlpool advised it was back-ordered for 3 months. A week ago Whirlpool advised them it was now back-ordered until 5-27. They did not know whether wed ever obtain a replacement motor. After taking clothes to our sons house for a couple months to wash, we purchased another used machine to use until ours is repaired. It is beginning to appear that machine may be our permanent machine. This is a pretty sad testimonial about whirlpool. We have always used Whirlpool appliances but appears we may have to switch brands. And it certainly does appear these low water machines are garbage. Very disappointed in Whirlpool.

We have owned the Whirlpool Quiet Partner II for about 2.5 years. We purchased this from our local Lowes store (on sale). For the first few months, everything was fine. Then, the dishwasher stopped completing a full cycle and left the dishes somewhat dirty. I found online that I could reset the controls by pressing heated dry-normal-heated dry-normal quickly.When the cycle starts, I press cancel and then set the cycle I want and it will do it correctly. I do this every time I wash the dishes since I dont know when it will decide to stop working (wasting water and soap to redo).Now, the dishes are not drying and water collects on the ceiling of the tub. I saw this after a smell was coming from the tub (like mold) and when I looked up at the top of the tub, I saw water droplets hanging there and mold forming around the sprayer and back of tub. I have to wipe the ceiling dry now or just run vinegar through it often. I cant see paying someone to come out since service calls start around $70 just to come to my home. I did look at reviews for the dishwasher before buying but I wished that I had seen this site first. I would not ever recommend this dishwasher to anyone!

Today I had the unfortunate experience to have to deal with Whirlpool customer service and claims. I WILL NEVER BUY ANOTHER WHIRLPOOL PRODUCT again! My refrigerator, that was purchased in 2013, has a door misalignment problem. It is a known problem with Whirlpool (service pointer W107317828). My refrigerator serial number and model number are affected. Because I am outside the one year warranty, Whirlpool refuses to provide service that is required to fix this known issue with my model/serial number. After having to talk to four supervisors the only resolution that was given was that they would cover the cost of the 7/16 hex nut ($4.33). Dont get me wrong I do appreciate the offer.The two supervisors that were below her assured me that no one can do anything to assist me further. The attitude of the second and third supervisor was pathetic. After over a hour on the phone I was so disappointed that I could not take it further. The cost that we are talking about that I am asking them to pay is $154.28. I am very disappointed. They say they stand by their product. To me standing by your product means that you will fix or replace any known issue. $154.28. I hope it is worth it to you Whirlpool. You lost a long time customer.

This is a defect due to the removal of the dispenser heater being removed. The insulation is inadequate behind the ice/water dispenser (@ 3 feet from the bottom of the door.) Replaced the line, thawed it out multiple times, added extra line under the fridge in the coils to try and warm up the water in the line between the 90 degree elbow connector and the dispenser... no luck. Since all the manufacturers models are being assembled in Mexico, using the same designs, other models are have the same issue. GE is backing theirs with a replacement freezer door. Well see if Whirlpool backs theirs. This whirlpool Gold is @ 3 years old and the issue started around a year ago.

I bought a Whirlpool water heater 5 years ago and after one year I had to replace the thermocouple every 3 months. Each time I call to complain, they would just send me a new thermocouple. I asked them several times to replace the item and they refused and just continued to send me replacement parts and refuse to honor their warranty. The water heater had some type of defect, but they still refuse to replace the item and did admit on the phone they have records of several parts that they sent.

The machine works well but it is extremely noisy. Large loads need to be washed twice otherwise they seem to not be washed. This machine washes small loads better. Given an option next time I will buy a front loader.

My $800 Whirlpool Cabrio top loader does not rinse the soap out of the clothes. Nor does it even get the clothes completely wet. After the final cycle I have soap scum in all the wrinkles of the clothes. Most dissatisfied purchase I’ve ever made. The one-star rating comes from the pretty blue digital displays. I’ll be purchasing another; this one goes to the dump where it belongs!

In the last 6 years I have had two refrigerators each lasting three years with major repairs from day 1. I am on my 6th repair for my Whirlpool Model WRF89SDAM02 purchased in October of 2013. WHAT A PIECE OF JUNK.

We bought a new refrigerator when we bought our house in Dec. 2008. On the third of July 2015 my Whirlpool Gold stopped being cold. In fact it was a bit warm. Had a repairman out here today. Warranty expired and the compressor has failed. Wow! Im not happy.

Whirlpool W8RXEGMWQ01 leaks - It looks like the seal is not tight around the freezer box. They blamed it on my floor but I think its because the door sags. The door needs to be lifted about 1/2 to fit snugly into the freezer box opening. They came out three times but couldnt fix it, then they said it was my fault. Then I finally gave up.

Whirlpool Cabrio washing machine - We purchased the (best name brand) from Get It Now and all we ever had was problems. We will fill the washer 1/2 full of clothes and the clothes on top would not even get wet. So we have to do it again, to make sure the rest of the clothes were washed. Many times there was white smudge marks on the clothes, sorta like powder (we use only liquid soap that you recommend). Today I washed a child’s bedspread for the 4th time because the stains would not come out (from a cookie). I had to turn the bedspread twice just to get it wet. I used bulk load and heavy duty load and it doesnt work. Your product is a very big disappointment for the price a person has to pay. I will recommend that no one purchase this product. Your people need to do further research on who this machine cleans clothes.

I also have a side-by-side Whirlpool Gold Fridge purchased from Lowes Retail Store, and I paid $1,480.00 for it. It is now 4 years old and I just noticed large cracks on right, inside part of the fridge. I called Whirlpool and got a runaround. Some lame guy said, Sorry, nothing we can do for you.When are people going to stand up for their rights and fight for their bucks? They havent heard the last of me but I will put this on the back of my truck with a nice sign on it for thousands to see. If anyone else has had this problem email me at ** and lets talk. I will never buy any Whirlpool items ever, ever again! Buyers beware! I also hold Lowes Retail Store responsible for this. They should research and stand behind what they sell, they are no better than Whirlpool!

This washer was expensive, platinum line. Clothes never smelled fresh and clean like they should. There is not enough water to cover and clean. After 4 years it started smelling dank and unpleasant even after cleaning cycle is run. Now I discover it has been leaking for quite a while. It will be 6 years old in July. The top wont stay up. This happened months ago. The part alone is 250.00 according to several sites. I just prop it up. Very displeased with this poorly constructed, expensive rip off!

The dishwasher is less than 2 years old, out of warranty, and will not start. The repairman said the problem is in the electronics. It would cost $500+ to repair.

I own a Cabrio Whirlpool washer. It already had several repairs and never got my wash clean. I complained to the company, no results. This washer is not even a year old. Why will they not stand behind their products?

The capacity is small but it does a good job of washing and drying the dishes. I always check to make sure that all dishes are washed including silverware and they are. My dishwasher is quite old but it is still sufficient for our use.

My review is not about Lowes, it is about the Whirlpool Range I purchased. I purchased a Whirlpool Range in 2013. In a matter of a few weeks the drawer at the bottom was giving problems. It was still under warranty and a repairman was sent to repair it at no cost to me. Something was broke about it. The drawer is so flimsy made it is not made to hold much of anything to start with. I have to take all sorts of effort to get it to close correctly. It is just shoddy made. Then a few weeks ago a piece of the side trim on the oven door fell off. My husband got it back on and then it fell off again last night. I am not happy with this stove, it is cheap made for $550.00. It is white with a smooth cooking surface. Drawer is so shallow and wont stay on the tracks, things fall out over the back. I am not satisfied with this stove, but I have got to keep it.

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..

Bought refrigerator in Jan of 2019. Quit making ice in Oct of 2019. 3 service calls and felt like it was band aided until manufacturers warranty ran out. Now waiting on new freezer door to be made. 6 to 8 weeks out. We will see. Called Whirlpool and was offered nothing. No customer service whatsoever. Will never buy another whirlpool product again.

Worst refrigerator (French Door Refrigerator WRF989SDAB00) ever! Even though this Technical Service Pointer was issued, it takes forever to get any satisfaction from Whirlpool. They were not pleasant to deal with when calling the Whirlpool Corporation. I had to research the problem while on the phone with their service representatives. The technician arrives and confirms that the evaporator in the fresh food section is indeed the problem but then it takes days for the parts to come in and then another appointment will be scheduled. Whirlpool does not provide good customer service. A refrigerator should last more than three years. Very disappointed and would never recommend Whirlpool to anyone.

I bought a Cabrio Washer and Dryer around January 2015 at Lowes. After going through the worse service imaginable, the washer was like pouring salt in the wound. I like the dryer fine, but months later, Im still unhappy with the washer. While it washes OK, it takes forever to wash a load. Most of the time, it does not spin the clothes out enough. There is no way to just spin again. You have to go through a rinse/spin cycle and you may or may not get lucky with a sufficient spinning. Why cant they just have a spin cycle and why does it have to take so long to wash a simple load of clothes? I have bought many Whirlpool appliances, but this is my last ever.

I had sold appliance for ten years. I purchase a Whirlpool Cabrio 2010. After two years started rusting. It is rusting on the outside and now on the inside, that I cannot wash delicates or whites. I so disappointed. I had lots of confidence in Whirlpool. The model is wtw7300xwo... I call talk to whirlpool but got no help. Now I going to need to purchase a new washer. It will not be a Whirlpool.

My parents 89 and 76 years old bought a Whirlpool fridge a few months ago. A month after purchase fridge built up moisture terribly. Water was laying inside so much seeping on floor. We called, Whirlpool sent serviceman out. Serviceman number 1 put some kind of black tape in the door saying it was the seal. We were just disgusted over this and it didnt work. We called again, serviceman number 2 came out, said bad door, so he ordered door. Serviceman number 3 came out, replaced door. Moisture still in fridge, food isnt staying cool, and you can physically still see gap indoor. We called again. Serviceman number 4 came out and said fridge is not level due to floor in house. But nothing wrong with floor in house. This serviceman pushed on fridge said to my 89 year old dad and 76 year old mother and I quote, Put a piece of wood under this side of fridge. We will not replace this fridge. Now mind the fridge was delivered and set up by Lowes. So now this brand new fridge is no good and we have had no help whatsoever to fix this problem. So my parents whom have been married for 62 years with 5 grown children, 16 grandchildren, a 36 greatgrandchildren and 1 great great grandchild have promised none of us will ever look at another Whirlpool anything much less purchase a whirlpool appliance. Just for the simple fact of how a multi trillion dollar company will not stand behind their warranty nor name. We are disgusted with the whole situation. This is the worst experience any of us have ever had. So no I would not recommend Whirlpool to anyone for the simply fact of the way my parents have been so disrespected by this company. Its horrible to know this kind of behavior is even allowed for employees to disrespect people. The Whirlpool fridge is warped, damaged from the time it was built. The warranty I hold in my hand says and I quote after 3 visits and problem not fixed fridge will be replaced.Well Whirlpool has been out 4 times and has refused to replace it. This couple has worked hard all of there lifes, lives on a fixed income and has just threw away money on a Whirlpool fridge they cant use. So now we have are in the process of hiring a lawyer. Its the principle of Good Vs Evil with Whirlpool. How whirlpool has refused to stand behind the Whirlpool warranty. So Like I said earlier I would never recommend buying any product that has anything to do with whirlpool. Shame on Whirlpool just shame on them.

Bought on 9/11/2014 and installed by Lowes installers on the 15th. It quit heating two days later. Called Lowes and they said I would have to call Whirlpool. I did. WP had me metering with a multi-meter until found OTC button was tripped. Then they suggested I troubleshoot the elements and sent me a video. I called Lowes and they said they would replace. Later they called back and said WP would not give them a RA number and for me to call them. I did and the rep after much arguing directed me to call their factory authorized service, A & E. I did and they said it would be 33 days before they could come out. I hung up and called Lowes who called back later and wanted me to call WP again. This time they said they did not have a repair service close enough to come, but I could try buying the lower heating element and replacing it to see if that worked. I said no, the heater was brand new and they needed to fix it. Their next solution was have me contact a local plumber and arrange to troubleshoot, me pay the plumber and then send them the bill. They would reimburse me up to $100.00. Not acceptable and now the button has to be reset every few hours and the water gets scalding hot while it is heating. I called Lowes and they said they would get back to me, but I have little hope of a resolution. Product number is ** SN is ** Model is E2F50HD045V. Bought at Lowes, Lindale, TX.

I bought my fridge in late 2008 and I am already experiencing potentially expensive repairs due to what I believe is a defective design system, of which, consumers are having to bare the consequences for those who collected our hard-earned cash and delivered a lousy product! I saw so many similar complaints about the ice system on this fridge that I am almost positive that it qualifies for a class action suit and settlement. How about a collaborative approach to this since we have all suffered needlessly? Tell me what you think and if you are in on it.

I purchased this machine about a year ago and it is the biggest piece of garbage on the planet. The biggest problem is that it will not spin if the load is even slightly unbalanced. It does not clean the clothes. If you try to rebalance and spin the load, it adds more water and then gets stuck in a cycle where it drains and adds water forever. Do not buy one of these. I am finally surrendering and buying a different machine. A total waste of money.

Whirlpool 29 cu ft French Door Refrigerator WRF989SDAM - We purchased this refrigerator September 2013 for our new home. We moved in November 18, 2013. The refrigerator made a very loud buzzing/humming noise from the beginning and did not make enough ice. The shop we bought it from came on 2 occasions to work on the ice maker and finally totally replaced it. Then the rack on the bottom of the left door fell out and contained glass jars of pickled vegetables. They broke and made a big mess and etched our travertine tile floor. We called the shop and they sent their son out who put the rack in with duct tape which of course did not work so we took it out and put it in the cabinet. We had to pay to have the tile polished to remove the etching. On the weekend of November 15, 2014 the humming noise was so loud that we called the repair person again and they came out on November 17, 2014. At first they thought it was a fan motor but the freezer started making a loud noise and the owner came and said the compressor was going out. Our food was beginning to thaw and we asked if they could at least loan us a refrigerator to use. They brought us an old small fridge which was put in the garage. We took all our food out there. They came November 25 and picked up the fridge to be repaired. We had been told the warranty was out but after calling your company they were told Whirlpool would cover parts and labor. Today is Thanksgiving Day and we can not cook a big meal due to the small fridge and freezer and we are buying bags of ice every day. We have family visiting and must go out for dinner. We have no idea of when our refrigerator will be returned to us. This has been an expensive and disappointing experience. I would never recommend your refrigerator to anyone due to this experience. I really feel we should have been offered a new refrigerator at a discount. We bought all our appliances from Dons Appliances in Okeechobee, FL 34974 and they are all Whirlpool. This refrigerator cost $2299 and our total order was $9,642.84. We would appreciate a response from your company.

Purchased a new home in Florida. Builder used Whirlpool appliances. For a year opening the refrigerator door has caused breakers to trip off. No matter what builder and Whirlpool do, breakers keep tripping. Cannot sell house with this issue. If someone was counting on electricity for a medical device they could die when refrigerator causes power to go out. Unfortunately, it looks like legal action is the only thing that will save our investment in the house.

I have had my fridge (model WRX735SDHZ02) for 6 months now and it has never worked properly. All our food was getting frozen so we bought a thermometer to check the temperature inside the fridge and it was showing around 22F. The technician came 4 times and finally said that the fridge couldnt be fixed. He asked me to call Whirlpool since there was nothing else he could do. Every time I have called Whirlpool (6 times already) the wait times have been between 52 minutes to almost 1.5 hours. When I called customer service to tell them the technician said the fridge cant be fixed, Whirlpool said that I had to contact the technician again and schedule another visit. Whirlpool said the technician had to call them from MY home and tell them the fridge cant be fixed. I asked why couldnt the technician just call them now to let them know and why did I have to schedule another visit for that? Whirlpool said it was protocol. Makes absolutely no sense. In a nutshell, its been 6 months and my fridge is still not fixed and Whirlpool is not being helpful. If I could go back I would not buy Whirlpool.

We purchased a Whirlpool Duet front load washing machine Model #WFW9550WL in July 2009. In July 2016, the guide on the door hinge broke, making the machine unusable. When performing a national search for the part number (#8183202) to replace the broken hinge, I found that there were none available anywhere in the United States. When talking to Whirlpool, they indicated that during 2015, they only sold 142 of this part, and were currently looking for a new manufacturer for the part. They further indicated that the part would not be available until late September or early October of this year.

In July 2018 I purchased a coin operated commercial front load 27 in washer and dryer. It was placed in and used in a six unit apartment building occupied by 8 long term adults. Prior washers and dryers had been operational for years with minor repairs at times. In June of 2019 the interior cement center balance on the top of the washer drum broke with resulting damage to screws securing the center balance and potentially other unknown parts. This was reported to Whirlpool customer Care service and they referred me to one of their a repair services. The repair service in about early August repaired the washer.In late September 2019 the cement balance broke a second time and this was again reported to Whirlpool service who requested I notify their recommended repair service. On inspecting the washer the repair service stated the entire washer was required to be rebuilt. The labor for installation of would cost me $1,125 with Whirlpool providing the parts under their warranty. The $1,125 labor cost was just under what I paid for a new coin operated front load washer. I reported this to Whirlpool whose supervising staff, without any inspection of damaged washer as to determine whether the washer was fit for its purpose when sold as a commercial washer, rejected any replacement of the less one year old washer and insisted they would only pay for the parts and I would have to pay for the labor, particularly when the both the cost of the replacement parts and the labor would be substantially in excess of a new machine. Due to time and effort constraints the problem was resolved by simply dumping the defective washer and purchasing a new commercial front load washer from a more responsible company.

The drawer guides on the large clear drawer at the top of the whirlpool refrigerator are very flimsy causing the drawer to drop when pulled out to the stop. When I called about this I was told it was cosmetic and not covered under warranty. I purchased the extended warranty which will replace the flimsy parts with the same flimsy parts. On 6/24/2024 Denisia sent me new side rails, exactly the type I have. I replaced them but the right side one broke. I regret ever owning one and will not recommend a whirlpool product to anyone. It is very obvious to anyone, after using this product, that that particular part is not safe and is definitely more than a cosmetic problem. I have already dumped the contents on the floor once and have just managed to catch it more times than I care to count. I spoke with Danielle on 5/14/2014. She sent the small plastic drawer that goes on the bottom.

After buying the best washer and dryer out there, I have found out that they are not. Thank you Whirlpool for taking my $2000 and giving me a junk. I know that you do not care one bit. Never again.

I purchased the Whirlpool Cabrio Washer thinking I was purchasing a quality product. Unfortunately it was one of the worst decision my wife and I have made. The bearings (lower) only last about 2 years. We purchased the extended warranty and the first time it was covered. The second set were not covered and now we will have to change them again. We will not ever purchase another Whirlpool product. I contacted them several times with no positive results. I still saved the last worn out bearings to show the CEO. The engineers do not have a very good idea to make the lower bearing last. Where I purchased the machine they told me after the first change that it would happen again and they were correct. If anyone needs to contact me about this product feel free. NEVER EVER BUY A WHIRLPOOL PRODUCT.

This Maytag dishwasher is awful. The parent company is Whirlpool and their customer service is as bad as their products. I bought this dishwasher and less than a week later the pump isnt working and stagnant water is sitting in the machine. It took Whirlpool 3 weeks to replace the machine and they sent over another defective machine. This time it lasted less than 2 days. The Whirlpool customer reps are rude and vindictive and antagonize the customer with their lack of service. Called corporate office with no help from Cust. Service and was told to leave a message with the operator and await a callback. With this fiasco I wouldnt buy another Whirlpool or Maytag product again. BTW. Im still awaiting my callback from the corporate office... Im not holding my breath. I called the company that I bought the dishwasher from to see if they can help me unload this machine and get a different brand...

Cabrio washer - This was a huge disappointment, clothes not clean, sometimes still dry in middle even with small loads! Have had washer just over a year, second time it has quit working! This time it wont even give a code to why it wont spin out! Living on a budget, I cant afford such a shoddy product! Never again will I buy any product associated with whirlpool!

After only 14 months of light use, the magnetron in my over-the-range Whirlpool stainless steel microwave failed. The cost to repair was $350. I paid $450 for the whole unit upon purchase. I wrote to Whirlpool with documentation and got a voicemail that they were sorry, but the 12-month warranty had expired. The independent repair person said it is the Korean manufacturer of the magnetron that is the problem. He is replacing units all over town on all kinds of models Whirlpool is involved with, including KitchenAid. Whirlpool needs to get their money back from Korea! I will never buy another Whirlpool product and have told them so.

Whirlpool Duet - Steam cycle and sanitize on wash. Dryer is fast and automatic cycles actually work! Have had the washer 4 years and the dryer over 10. We like the Duet Washer because it had a steam cycle and a sanitize cycle plus it has a light inside that helps us see the laundry in our dark room or at night. Also we have been very happy with the cleaning - does a great job and gets the dirtiest clothes clean. The Fan Fresh feature and Delay Start are very handy especially for busy parents who may forget the laundry is in the washer.

I bought a Whirlpool water heater from Lowes in the fall of 2009. For the first 4 years it worked fine. Since the spring of 2015, it started to stop working. I called the company, and they recommend their contractors to fix it. In less than a year, I had it repaired at least ten times. I spent more to repair it than I bought it. This water heater has a 10-year warranty on it. Per the companys recommendation, I replaced the thermocouple, clean it, have it regularly serviced. The technician told us we need to change the gas valve assembly. When I called, they sent a burner assembly. When I called, they asked me about the exhaust pipe, whether it is go through the roof or go through the side of the house. I took several pictures of the exhaust system and sent to them. I called, one of the people on the company side said my exhaust was wrong, and need to be repaired by a HVAC company. I asked what is wrong? They dont tell me. I sent emails, and called to ask an answer, and got nothing. My impression is that they dont want to deal with the issues and simply want the consumer to get tired and replace the water heater. It really shows the total disregard of the interest of the consumers. This should not be the way people do business in the United States. When a big company has large numbers of lawyers, they can ignore the law. What a corrupt system!

I purchased a Duet Front Loading Washer (model WFW9750) in May 2010. In September 2011, the noise level had become intolerable. I called a local service company. They advised me that the main bearing was bad. It would cost more to repair than what it was worth. I contacted Whirlpool. They could not do anything unless the machine was inspected by one of their authorized service companies, which they scheduled. Two weeks later, A&E Factory Service arrived and confirmed that the bearing is bad and the cost to repair will be $1,542.06. Whirlpool customer service transferred me all over the country to tell me that the machine was out of warranty and there was nothing they could do.

So I had a problem with the water heater after 2 years and had the sensor fix by my heating people. Now the water heater is 3 years old and started leaking from the top of the water heater. Called my heating people and they fix the pipe and coupling on top but he told me the water was still bubbling up at the top. He told me it could stop and 70% it would be ok. Went to check on it and it continues to leak so I called Whirlpool because it was still under warranty. They are the most horrible people to deal with. First of all I told the guy it was leaking from the top but he asked me if it was leaking out of the side pipe. Didnt know what he was talking about and he kept sighing on the phone. If I knew about water heaters I wouldnt be calling them. After all the questions it came down to it was leaking where I told him at the top. He gave me a number and told me to take the water heater back to Lowes and get a new one and then call them and they would move the warranty over to the new heater. Really???? We are not talking about clothes you want to bring back to a store. Asked him how I should do this and he told me to call a heating contractor. So does he think that the heating contractor and going to run the water heater back for a new one??? In the end I just called my heating people and they are going to send somebody out to install a new heater. So much for Whirlpools warranty. If this is under warranty and it is exclusive to Lowes then they should be having Lowes bring a new one and install it.

I purchased a WhirlPool dishwasher in 2016. The primary motor had to be replaced in 2018. WP paid for the part; however, I had to cover the labor, which was expensive. In 2019 the drying element broke. Again, WP will replace the part but leave me to cover the labor. Ive decided to purchase a new dishwasher (none of the Whirlpool brands) with a 5 year warranty. I will never purchase another WP product and recommend everyone avoid all of their brands. Heres the list of brands you should avoid. https://www.whirlpoolcorp.com/brands-we-love/

I love my Whirlpool Washing machine. Purchased it 2 yrs ago & have not had any issues. Its quiet, large capacity. Washes my clothes very clean. The various washing cycles makes it so convenient to wash as much or as little as I need on any occasion. I do recommend to anyone that you do the cleaning cycle on these new washers to ensure top performance when washing.

Our home came with an Asko dishwasher, theoretically a premium device though the experience was not the best. Anyways, had to replace it after a few years and decided to buy a Whirlpool under the assumption that if an Asko kind of sucks, being so expensive, it was not worth the money to spend big bucks on an expensive dishwasher. I could not have been more wrong! Bought a middle of the pack Whirlpool, I think we spend around $500. Complete junk. I had to use our Sears home warranty like 6 times. They replaced two times the computer board, all the sensors another couple of times, motor, you name it! Worst part is that all of the non essentials part that also broke off (wheels, and plastic pieces of the door) were not covered by Sears warranty so I had to end up using glue and all kind of contraptions to keep them together. Finally, when we decided to put our house in the market we replaced this junk with a Bosch. So far so good. Whirlpool actually never even washed properly, now with the Bosch we finally know what it means to have a dishwasher that really washes for real!

Bought this machine in July 2015 to replace LG front loader that went bad. This machine is the worst at rinsing the soap out of dark clothes, and probably the whites and lights too! Dark clothes always have white streaks and spots all over them. Called Customer Service and was told it was due to too much soap, the way the clothes were loaded, needed to add an extra rinse cycle to load, and/or because there is a water softener in the home. Have changed soaps 3x, changed the way I was loading the clothes, and I doubt the water softener has anything to do with this problem. I dont see how adding an extra cycle is efficient and seems wasteful. This machine is horrible and whether I just got a lemon or if its a defect in this machine, I dont know. Whirlpool doesnt seem to care either. I am going to attempt to sell this one and will not consider Whirlpool for the next one. Do not buy this machine!!

We purchased the Whirlpool Cabrio washing machine around January 2006, and from the start weve had nothing but problems with this appliance. Within the first year, water was leaking under the washer which was coming from a crack in the plastic housing of the water pump. I replaced the pump myself to save on labor. No big deal. The very next year, I started getting the F51 code and there was no way for me to get around calling a service company to have it repaired. $350 and one circuit board later, it was repaired. It remained working without fail until recently when it began giving the same F51 code. Let me guess, another $350 for better repair? I have to assume that the new circuit board that was installed wasnt any better than the original one that was replaced. I wouldnt put another $1 into this hunk of junk and Whirlpool should be ashamed to have this product on the market. I will never buy another Whirlpool product.

Whirlpool model WRF560SMYB04 - We purchased this model Whirlpool in Dec 2015 after having a refrigerator for 18 years with no problems. We started having cooling issues in late 2017 and finally an intolerable fan noise in April 2018. Researched it and purchased a fan. Opened up the freezer panel and found that the unit was completely frosted up to the point where ice had formed around the freezer fan and was hitting the blades. Contacted a repairman who came out and called in the issue to the Whirlpool tech line. He was told that he should check continuity on a couple of wires. If these checked out, the problem was the user interface board at the top of the refrigerator. We purchased a new board for about $100 and installed same. No change. I was now $250 into repairs and no further. We became aware of Whirlpool Service Pointer W10875533A which described conditions that we were experiencing. The issue was a coil thermistor that would corrode (apparently within 2 years) and would not provide accurate signals. Whirlpool also issued an instruction sheet W10902213 Rev A describing how to relocate the thermistor and protect it with foil and tape. My repairman came out, confirmed the thermistor ($54) was bad, replaced same following the Instruction Sheet. We were now out over $300 on a $1000 refrigerator purchased 2 years earlier.Whirlpool issued the Service Pointer (not to consumers, but to repair shops) in Sept 2016 (within our warranty period). We received no notifications from Whirlpool of the defective design. Nor did we receive a recall notice. Moreover, Whirlpool tech group must have known about this issue, but instructed my repairman to replace the interface board. Whirlpool knows they have a defective product out there but are doing nothing to inform the consumer or stepping up to correct the problem. We have contacted Whirlpool to recover our expenses...will let you all know how that goes. Anybody interested in pursuing a class action?

I just purchased a top load wtw5000dw01. There have not been any changes to this revised model except the lid only locks in the rinse/spin cycle now. If that even helps anybody. It still has the noisy agitator which is the thing I hate most. Whirlpool engineers better go back to the drawing board and redesign their washers. Whats this country come to when you spend a pile of money on something that sounds like it is broken from brand new. I also had a washer that was 15 years old and never had noise issues or problems with it. Its just not Whirlpool that uses this so called new technology.

Four microwave ovens to finally get one that works. Four months after purchase, the French door fridge accumulated ice, 3/4 thick, in the bottom of the freezer compartment. I had no knowledge of this until the drawer became difficult to open and close. Lowes is replacing the unit.

I purchased model FG1F4040SEPV Whirlpool water heater from Lowes about 5 years ago and have had to literally replace the thermocouple each year. At least 3 of these years we have had to pay someone to fix this for us until we learned to do it on our own. Im very surprised Whirlpool didnt recall these water heaters and make it right for their consumers. What this did for us was confirm that we will never purchase another Whirlpool item ever again. We are switching over to Kenmore!

At after 4 years of use, my double door refrigerator is giving cooling problem. Upper refrigerator part has excessive cooling and lower part has no cooling... after complaints in customer care, engineer was sent who changed the part that regulates auto cut... it gets blocked by ice so cooling air is not reaching lower part. Once changed exactly after 5 days same problem started... In spite of complaints no one came to check for good 2 wks. After long fight, it was defective board that was changed again. After 3 days same problem again, board was changed... Now after 2 and half month same problem. And now today service center has replied that engineer will be sent after one week.

We have had our range for over one year. The main problem is that the large burners are in the front and the small burners are in the back. This means that when we are using the two front burners we cannot access the rear burners safely. (What country provided the engineering design for this?) One minor problem is that we cannot get used to the burner control arrangement. The outside controls control the front burners and the inside controls control the back burners. Our old range was the right control for the back burner and the left was for the front burner. Another small problem is that there is no back to the pan drawer. So, with the drawer full if a pan move when the drawer is shut it will be scraped off the drawer and fall into the back and becomes hard to reach to remove.

Whirlpool Clothes Washer Model WTW4930XW1 - We have experienced tub overfilling on (2) separate occasions with this washer model in a period of time of less than (2) years. Through extended warranty service purchased, a technician came out the first time; declared nothing explainable to cause the malfunction, re-calibrated the control panel, and off he went. This second event occurred much the same as the first; happened to walk in to notice water on laundry room floor and witnessed overflow out the lid on top. We have carefully washed additional loads after this second event without a similar malfunction. From my online research, this sure sounds like a faulty pressure switch not sensing high water level in the tub. Any other thoughts?

Do not buy whirlpool water heater!!! It will only last 3 years.

Whirlpool N50T91-403 purchased in Mar 12 had an error code 4. I knew the water heater had a safety installed in it when I was working on the plumbing and allowed it to drain the hot water side down to 16% of capacitance of 50 GL. After the plumbing issue was resolved, I saw the water heater had shut off (thermal protection) but the switch wasnt tripped as far as I could tell. Knowing small processors can only remember anything if they have power, I removed the Honeywell circuit board and with my multimeter probed all of the capacitors contacting them both (-) and (+) and in reverse order. Doing this forces the IC to forget its codes because they require a small amount of voltage to remember them, usually powered by a small capacitor. I reinstalled it and voila! Presto! It works again.

Purchased my Whirlpool Duet front load washer WFW9150WW00 new in 2010. Also purchased extended warranty. After four years, just before my extended warranty was up, the entire inside needed replacing (drums, bearings). Now at only five years old, it keeps making a beeping noise in middle of wash cycle and wont continue working. Serviceman was told by a Whirlpool tech. that it could be two things, one being the door jamb, the other being the control panel. Door jamb was fine. Ordered new control panel ($240), had it installed and yet the washing machine still keeps beeping and doing the same thing. The serviceman doesnt know what else it could be. So, I am forced to return the part and purchase a new washing machine. I would never recommend Whirlpool to anyone!

The home I bought a few years ago, had brand new Whirlpool appliances. The oven and range, work great, although it does take my oven seems like a long time to get to temperature. The size of the oven is great, has plenty of room to cook lots and/or large amounts. The range, works really good too. Its a glass top range. The glass is very durable, I find it does not scratch easily. Cleans up well by just using a good glass top cleaner. I do have one of the burners, does make a little noise if used but 4 years in, no issues out of the range or oven.

Whirlpool ADP100 wh. A few programs, washes well, dries ok, not great but ok. Standard free standing size, 60 x 85 x 59 cm. The washer itself is fine, but oh the cheap moulded plastic parts, utensil basket, water arms etc, so poorly made. Its amazing that a company would use such poor quality and design to save what can be a few cents on the overall product, personally I was disgusted at the cheap crappy plastic bits.

This stove is a joke. The range gets too hot even when you have the setting on low. The oven now has started becoming hot when its not turned on. Goes up to 245 and its scary. I have to turn off the breaker to ensure it gets cold again, but Ive had to do that every day for a week now. I will be calling Whirlpool to file a complaint. I have small children and Im scared my house will catch fire or have a unnecessary increase in my electric bill.

Literally from day one I had an issue with my Gold Series which was aggravating but at least it was on warranty. Then 2 months out of warranty I had another problem, a leak. Now no water circulation. I think it is maybe 3 years old. What a piece of junk and my Whirlpool washer and dryer? Not much better. I will never buy another.

I bought this Whirlpool dishwasher 3 years ago and the first time I used it I was completely blown away. We can run it at night and never hear it. The first time I turned it on I had to go back and check it to make sure it was on.

I bought a 50-gal. Whirlpool electric hot water heater about 6 years ago from Lowes. About every two years, something goes bad. So far, I had to replace electronic control board that sits on top of heater twice. Then the heating element went bad. Well, this time, the electronic control board started to smoke and melt. I was home so I smelled something melting and found it. What would have happened if I was not at home? I have dogs that are like my kids; they could have been killed. Whirlpool wants to send the replacement parts knowing this part is no good. Do not buy a Whirlpool electric water heater! Now, Im scared the next time I wont be at home to find the thing smoking. I dont have money to buy a new one. How many other people have the same problem?

We purchased a new Whirlpool Cabrio Platinum W10405142B washer and dryer just over 3 years ago. We decided to go back to the top load as we were having so many issues with odor from our front load. We purchased the set at a Sears store in Timmins Ontario and we’re quite confident that we were getting an excellent product. From day 1 we have had issues with having to rewash our clothes. We have lint and white streaks on the clothes as if we were using powdered detergent and they are all tangled. We have always used HE liquid and at one point I switched to soap nuts to get rid of using chemicals. We have now changed to pods and still have issues. When the washer is spinning it is deafening. You can hear it outside for goodness sakes. It sounds like it is about to take off and fly.The cycles are ridiculously long. For a quick cycle the other day and a very small load it took 72 minutes... how is that quick? When the wash is done my clothes are all tangled up and are stretching things out of shape. I am careful what goes in my washer and how large my load is. I know not to wash sheets or towels when I am not home as they will eventually be unbalanced and have Sat all day in the washer only to have another hour of washing when I get home. We are currently doing some work in our home and pulled out the washer. The floor has a rust circle from God knows what. I will attach a picture. The lid not longer closes. I have to hold it down until it locks and it still pops up a wee bit.I do not understand why I am responsible for purchasing a new set when the product I bought should have lasted and not caused damage to my clothes or my flooring. How do we as consumers make the manufacturers responsible for things like this. If nothing else the appliances should be removed from my home by the Company and I should be reimbursed for damages and the cost of a new set. I will continue to look for my receipt as I keep everything and I am unsure what is meant by order #.

Maybe they make some higher end ovens but ours was not one of them. The oven light fixture works intermittently and its only been 8 months that we have had it. The insulation on the oven is lacking as well. You can turn the oven off at 450 and within 15 mins its already below 200.

After only two and a half years, my Whirlpool bottom freezer refrigerator (GB2SHDXTQ0) was frosting over and the top food section stopped working altogether. I made a call to Lowe’s. It’s not their problem. I then called Whirlpool and he said I had a bad gasket. I had a 28-year-old refrigerator that was still working with the original gasket and it has no problem. After reading all the complaints with Whirlpool, I would never buy another one again. After cleaning out the refrigerator and freezer two times, carrying things to a friend’s house and having to pay $90 service calls just to walk into the door, I am ready to throw this one out. This refrigerator cost me $1200 and I am a single person living on $900 a month. Thanks for nothing, Whirlpool. There should be a class action suit.

I have a model ED20PK. The doors are rusting on the outside.This refrigerator was purchased by my husband who has passed, I do not have the receipt and I dont know where he purchased it. The refrigerator worked perfect. It has been in my kitchen from day of purchase. My home is adequately heated in winter and air conditioned in the summer. I have an up-scale home. I dont see any reason to replace the refrigerator, but I cannot stand the deteriorating condition of the doors.If I replace it, I will not buy a Whirlpool or any brand made by Whirlpool.The rust is not just a discoloration, it is actually rough to the touch and is getting worse day by day. If you have any answers or help I would appreciate a phone call. I am not really in an economic position to just go and buy a new refrigerator.

In 2002, I purchased an EE3Z50RD055V 50 gal. Whirlpool hot water heater. Recently several solder joints on the computer module became unsoldered so I cleaned the joints and resoldered them. But several months later another joint became unsoldered so I thought Id just purchase a new module. I called 1-877-817-6750, explained the problem to the young lady. She informed me that they would ship me a new one overnight. I asked her how much this would cost and she told me there would be no charge as it had a lifetime warranty. SURPRISE! Thats what I call customer service! A few years ago, I purchased a Whirlpool Duet front load washer and dryer. Now Im twice as glad that I did. My wife and I LOVE the Duet.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

I bought an whirlpool stove from conn store in 2007. The oven hasnt work right since day one. They send different people out to service it - still dont work the right. We smell gas when we try to light it. It wont come on 90 percent of the time, sometime we have wait a while to start it. They refuse to exchange from day one, we cant afford to throw our money away so we do more top cooking than bottom.

1.0 out of 5. This is the absolute worst washer that I have ever owned. Do NOT fall for the top loader hype. The clothes do not get clean. Anything black constantly comes out with a white residue and whites are dingy. Ive tried numerous detergents and used as little as a tablespoon and still get the same results. The company just insists that its too much detergent or that I need to run the clean cycle after every 4-5 loads. The service guy that came out said this is the number 1 complaint with these washers and Ive talked to plenty of friends that experience the same issue. The company would have you think this is the first time they have heard of it.I have spent hours on the phone with whirlpool and Home Depot over the past year and neither accept responsibility or offer any solution other than some free cleaning tablets from Whirlpool and Home Depot offered $200 off the purchase of another washer. This was when the washer was only 6 months old. The only way around this is to rewash the clothes and a second cycle and to wash all loads on bulk load with an extra rinse. Yep. Great water savings there! Save yourself the headache and dont buy a top loader of any brand and I would never buy another appliance of any kind from Whirlpool and Home Depot because of their poor customer service in handling this common issue.

The first thing I noticed after purchasing this stove was that the glass top did not clean properly. I used the product given to me by Sears and tried several others but still could not take marks off of the glass top. I never really used the oven that much until retired and started baking often. The self clean does not work at all unless by self clean they mean that you yourself cleans -- I should say scrub it down. I previously had a regular self clean and it truly self cleaned. All I did was take wet paper towel and wipe out. Yet when I asked the Sears saleswoman about how it cleans I was told that it was terrific -- I would not have any problems! What a laugh!

I purchased a Whirlpool side-by-side refrigerator from Lowes for $1,100. It arrived missing a shelf. Last year, the warranty expired and the ice maker mysteriously failed. Next a drawer slide failed. Next the lights, both of them, failed. I was offered a service call, the estimate $300+. Next, the ice bucket bottom broke and filled the freezer with cubes. Next another drawer slide failed. Whirlpool makes an over-priced, poorly engineered, poorly made product and Lowes sells their products without any care for their customers. I will do my best to warn anybody who is interested that while Whirlpool used to be a good company, it has degraded into producing junk and trading on a once storied reputation. And Lowes touts these products without any interest in its consumers.

This $1,000+ Whirlpool Cabrio washer high-efficiency machine should have lasted between 10-15 years, not 1, not 2, not 3, not 4, not 5! To expect less is to fall for the consumer cave in - where you just give up, give in and buy another. The Whirlpool tech just told the appliance repair guy that was here that the repair would involve a recirculating water pump and a bearing, and would cost $481 to repair. The appliance repairman said he is not in business to condemn appliances, but said he has a Kenmore top loader at his house. Simple, no electronics and less things to go wrong. Well after researching brands and reading reports, I thought I was buying a machine that would last at least as long as my second hand Maytag. Whirlpool has not heard the end of me. I have heard several other people say the same thing. Repair bills are huge and machines do not hold up. So much for buying quality. Now Im going to contact the MA attorney general for the states implied warranty, which means if you spend your money on any appliance, that appliance has an expected lifetime of service. A $1,000+ machine is not expected to fall apart after a few years.

I bought my first Cabrio set in 2008 to replace Maytags that lasted forever but looked their age on the outside. No problem with cleaning and drying, just wanted something new. What a mistake! I looked in Consumer Report Guide to pick and found the Cabrio set. Had problems after the first 4 months - UL uneven load codes flashing up, and had to replace suspensions and bearings, boards, etc. Unfortunately within that 4 months I bought another Cabrio set to put in my vacation home. Started with the same issues and really hard to get a service technician to come out because of where we were located. Customer service with Whirlpool sucks as well as Sears service. It is AMAZING to me that Whirlpool will NOT stand behind this product. I am writing this as I see an F1 code flashing on my washer here at my second home. I have a load of towels in it and house guests arriving in the morning! I will be trashing this washer and dryer and finding something old school and reliable. I want no bells and whistles, just clean and dry clothes. Whirlpool, you should be ashamed.

Moved to new house with new Whirlpool appliances, including oven, in August, 2015. I did not cook in oven at all until Thanksgiving meal. Had something spill over in oven. Spillover caught fire. Oven at 350 degrees. Complained to Whirlpool. A supervisor told me that it is normal for spillover to catch fire. They sent out a tech to check oven, and said I would be responsible for paying tech. The tech explained that unlike conventional ovens, this oven has heating elements outside of oven, so to get to the temperature of 350 degrees, the heat at the bottom of oven can get to over 550 degrees. He could not get Whirlpool to replace oven. I didnt have to pay, but now I am afraid to use it. Some of the finish on the inside of the oven was burned away, so it is not like I can trade it in. I feel the oven has a defective design if spillovers are supposed to catch fire while you are cooking, and the finish gets damaged. I will never buy another Whirlpool appliance again, if I can help it.

Smelled strange odor in laundry room area.. Noticed plastic panel to Whirlpool electric water heater controls was melting and immediately closed breaker to the heater.. After inspection of heater control panel, noticed all wiring damaged and burnt causing burning smell.

Water began accumulating on the floor, dripping out of the freezer 16 months from installation. Upon investigating I found the bottom of the freezer had a solid sheet of ice on it. Water was dripping out from the back of the freezer and collecting until it froze. I followed a YouTube video that explained the problem, the freezer drain clogs. The video continued with a how-to dismantle the freezer to defrost the drain and drain the water. Apparently the drain is too small and the fix is a new grommet which costs approximately $27.00. I followed the YouTube video and TEMPORARILY fixed the trouble myself. This is a Whirlpool defect, aka, poor design. What is Whirlpool offering to customers to permanently solve this problem at no cost?

First three months, the main water gasket broke. Thank you for lots of water all over the kitchen. I pulled the washer out to inspect the cause, wanted to see if it was house plumbing or dishwasher. The hose was hanging off the bottom of the machine. During the 45-minute call, I got in my car and drove to plumbing supply and applied a new hose clamp. The next day, a free service call, the repairman said it was the second one this week, Thats just what I would have done, but would not put the machine back. (void the warranty, finish work, etc...not sure how he would have serviced the machine if I did not pull it out for him). A few months later the wheels on the top shelves give way/fall off the rack, so we have those replaced. As soon as one is replaced, the other side falls off... Now, approximately 14 months into installation, the dishwasher does not work. The control panel is flashing and will not start. What a runaround with KitchenAid. We were told there was a recall on the hose clamp (we never got one). We cannot have the control panel worked on until the hose clamp is certified... That will take a week. Then we can call back... What a hassle. We bought this expensive product on good reviews. We are most disappointed. There is very little concern for making the product good. Its incredible that so much can go wrong in such a short time of limited use. Once/day... The hose clamp is just poor engineering. The rest is terrible quality and support

I purchased this machine in April and already, the right leg is rusted and the under seam of machine is rusted. I have throw rug under it and where the leg is, there is rust on the rug. I called service from Whirlpool and 2 servicemen came out. The first one told me I was loading it wrong and the water was splashing over the inside tub to rust the leg and I asked, So why is the seam under the machine rusted? No answer. The second one came out and told me he could not find anything wrong with the machine and doesnt know why it is rusting, but he never gave me a paper to sign off on. He also said that maybe it was rusted when it was delivered. Not!!! Then I call P.C. Richard in Watchung, NJ where I bought the machine at and told them about the problem. They sent a serviceman out and he said that the bleach condensation is causing the rust, its known fact that this machine has this problem. He said that the water does not run through the dispenser but there is a model that does. I want a credit on this machine and get the upgraded one. It states on the machine that I can use bleach but it doesnt say it will cause rusting. I want you to tell me how a 9-month-old machine is rusted on one leg and the seam underneath is also rusted!!!! I had a machine for 10 years and it wasnt rusted. I am very unhappy with this product and with the customer service of Whirlpool. This is my first Whirlpool washer and I would not recommend this washer to anyone. I paid $600.00 for this washer and it should not be rusting.

We purchased this washer in 2017, its the top loading Cabrio washer and it has been nothing but junk since day one. Purchased from RC Wiley in Boise and unfortunately did not buy the extended warranty because we trusted that this American company would make a washer that would last longer than 3 yrs. This washer barely washes clothes, leaves a residue on them since there is no agitator, also constantly gets unbalanced or gives and error of LF which means water supply issue when there isnt one. My 15 yr old about has a heart attack when he uses the quick setting and his clothes arent done in an hour and a half. Ive even resorted to turning the thing on to just rinse and spin so things get done sooner, still the stupid washer just sits. I would sell it but I dont want to pass on the pain, so its going to the dump to or to Goodwill cause its not worth the headache. Too bad you cant trust an American company to make a good product. Sad I really wanted to like this washer.

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

I purchased a dishwasher and hooked it up. The reason I install products myself is I dont like people in my house. I dont know if they are there to help or inventory what they plan to rob from me later. It did not drain so I called Whirlpool who said that I probably hooked it up wrong. Whirlpool said that they would send a service man but if it was hooked up wrong I would have to pay for the service. The service man did arrive and had tattoos all over his neck and arms. (A tear drop would have confirmed that he was a murderer). The machine was hooked up correctly, the water pump was not working at all. The service company that Whirlpool contracted took 3 day to order the part. Yes three day to even order the part. Then another 10 days to get the part in. I called Whirlpool and they did not seem to care at all. My thought is, I am out $599 plus tax, and I have to wait 2 weeks to get my machine fixed, plus I have to take hours off work to wait for the service man and now I have to worry about the service man breaking into my house and robbing me and Whirlpool doesnt care. They should have to pay for the time I was off work and for the interest I lost on the money not being in my account during that two weeks. Whirlpool didnt care at all though. Worst customer service ever. Used to be that Made in America was something good. Not anymore thanks to companies like Whirlpool. Made in America = Garbage!!

My whirlpool refrigerator relay switch caught on fire and customer service told me that my model wasnt on their list of problems refrigerators, but they know there are a lot of units out with the chance that it could start a fire if anyone has a whirlpool product refrigerator. I would call 1-888-923-8502 and check to see if it is on there list to replace the switch.

Its big enough, but the ice maker is always messing up, the shelves broke easily, the water takes forever to get cold from the indoor dispenser. The finish, which is called Satina or something like that, dents real easy. It is really a piece of **! When it was new, we had the repair man out 4 times before it was fixed. He even said it was a piece of junk and it should be lemon lawed out. Drawers broke, shelves broke, and parts are really expensive when you break one of the plastic parts.

Ice maker not working. Freezer not working. Fridge not working. There is some cooling in the fridge/freezer system - maybe 50 degrees. Not under warranty, 2 years old. Repair person is coming. Will edit when I have more details.

In June of 2010, I purchased a new Whirlpool Estate EED4400WQ0 dryer (serial number M01156261) with an accompanying washing machine. It has been in a clean, climate-controlled environment and gently used by my family of four for just short of two years. Last week, I began to notice that the clothes coming out of the dryer were cool and damp and it quickly became apparent that the dryer was only heating intermittently. This morning, the service person from the dealer who sold me the washer and dryer set (and a Whirlpool dishwasher a few months later) told me that contacts on the timer unit were bad and that the entire switch would have to be replaced. This is no small portion of the machine and the part alone will cost me about $150. After labor, we are looking at an expense of approximately half of the original cost of the machine - in less than two years. I called the Whirlpool’s customer service line to ask if there was anything that could be done and the answer was: Sorry, we cant do anything for you.” It is not acceptable to me for an appliance to become that expensive that fast. If Whirlpool cant do anything for me about this, then I will not be purchasing anymore Whirlpool products.

What is the brilliant idea of a mode dial on a washing machine that needs to be pushed in or pulled out to engage its function??? In other words, why is there a free-spin mode of THE DIAL itself? Okay. IN OTHER WORDS, why not just let the handle part of the dial stay affixed to the red line mark, so that they continuously turn together at ALL times???

Purchased a Whirlpool refrigerator July 29, 2015. Our first service call was August 4, 2015. The units freezer was frosting over, the basket rails were covered in frost, which made it hard to open. Items in freezer containers were covered in frost and labels unreadable. The interior light was frozen shut. Since the first service call we have had 8 service calls with multiple appliance dealers. No one can fix the frost issue. It just keeps recurring. Whirlpool did step up and extend our warranty for another year. In order to schedule a repair we have to call Whirlpool, a 45 minute phone call for an appliance company not of our choice to make the service call. The unit has been removed from our home for repair in dealers shop. Very inconvenient for us to have no refrigerator. Whirlpool has refused to replace the unit, choosing instead to patch-patch-patch one service call at a time. Whirlpool has enjoyed years of an excellent reputation. We are very disappointed. This is no longer true.

Never ever plan to buy a Whirlpool product. I took the washing machine in December 2008. System was not got at first time also. I called service center, and he came and asked to put this and that. Again, it got a problem. This time, he told me to change powder. I was shocked how a powder became a problem for its failure in washing clothes. Next, he told me to put a stand. After a long interval of 6 to 7 months, I got fed up and called him again. He told me it was not in the warranty. Its the worst service. Zero percent satisfaction Hats off to Whirlpool service. Please, friends, never buy cheap Whirlpool products.

Whirlpool Cambridge Model #WTW7300DW0 - Someone needs to help us consumers with this wash machine purchase being refund our money back from Whirlpool. It literally eats my clothes. I have 23 shirts that have pin holes in them and 1 shirt with large holes in it. I also have a ruined comforter and blanket. The comforter has soap stains everywhere which dont come out so its not cleaning the clothes, the blanket (which Ive had for over 30 years) was frayed one side, seam torn off - the piece never came out of the wash machine. I have pictures attached of the damaged. Its suppose to be Water Efficient - thats a joke! I do 1 set of king sheets. It runs for an hour and 20 minutes and fills water to the rim of the washer and does this twice. Id like them to pay for my water bills! Oh they came to service it only to tell me I was putting the clothes in wrong. The service company said I had to put the clothes against the sides and leave the middle open. They told me there was nothing wrong but consumer error. Well I did clothes today and aligned them like the service company said - 4 more shirts were ruined. Called Whirlpool today. They said they were sending someone else out to fix the problem and said, Unfortunately, we dont pay for damaged goods. Well from all the reviews I read Whirlpool needs to suck it up and recall this piece of crap they call a wash machine. Did I mention its only 1 year old, yea this is horrible!

I have always used Whirlpool products and have grown up with them. From washing machines to dishwashers. Not only is it made in the USA but its reliable. The only problem is space and it can do with more freezer space. Other than that its a great refrigerator.

Whirlpool convection/microwave GMH6185XVS - In 2011, we purchased a whole new kitchen for our home with the top of the line Whirlpool products. The sorry side of this project was our microwave. This product has been terrible for us! It has been removed from our wall 4 times for failing... and four times we have gone for weeks at a time with a big hole in our kitchen wall!! All of the failures were due to the microwave not heating food or drink, and all, according to our local dealership, were for various different reasons. Again, it has failed and our local appliance center who we bought everything from does not want to deal with it anymore. I dont blame them... I dont either!! It looks beautiful up there above our range telling me the time of day... My wife and I are older adults and take very good care of everything we own. There certainly has never been any abuse to this product (not to mention we spend half our year at a winter home so this microwave only is used for 6 months a year). I contacted Whirlpool customer service about the reliability of this product and their response was that it is now not under warranty and we should deal with our local store about repairs. I have a small Sharp microwave sitting on the counter below this crappy excuse for one that stays there all the time in anticipation on the Whirlpool going down!!! The $60.00 Sharp never fails me!! This was our 2nd time around purchasing all Whirlpool products for our house. We did the same thing when we built back in 1990. All appliances performed as they should have back then. It seems Whirlpool integrity has gone downhill. I will never buy another Whirlpool product nor I will recommend to anyone I know to do the same. Good luck to anyone who purchased one of these.

In June 2010 my wife and I bought a new Whirlpool water heater (model ee2h50rd045v). As I have fairly extensive experience in both the electrical and plumbing areas (was head lab technician for an aquatics lab for 7 years and worked with maintenance on a farm for 10 years), I installed the unit myself. Two months later the motherboard fried. Whirlpool sent me a replacement and all was fine. Six months after this the motherboard fried and set the unit on fire. Luckily I was home and caught it before it got out of hand and the circuit breaker had tripped when this happened (the circuit breaker saved the house).After I had ripped the smoldering unit out of the garage I immediately called Whirlpools Customer Hotline and told them what happened. They said they would send me replacement parts. I reminded them that the motherboard had fried once before and that this time the unit had almost cost me the house. I also informed them that I have now worked for Lowes for 4 years and I am responsible for selling their product (in addition to other brands). The lady stated all they could do was send me new parts and the problem probably was with my circuit breaker. I informed her the circuit breaker was tripped so the problem was not there. She reiterated that all they could do was send new parts.The next day I started to remove the control panel and motherboard to find that the plastic had fused itself to the frame and insulation. I called the customer hotline and spoke to someone new and informed them about the new problem with the melted plastic. I was told that the melted plastic could be scrapped off safely and that since the problem was not the circuit breaker, the problem must have been how the wires had been spliced from my conduit into the water heater. The gentleman then proceeded to tell me how to do it in violation of Maryland code and told me he would have replacement parts sent to me. I checked with a certified electrician to make sure my wire splice had been done in accordance with code and he verified I was correct.I then had a Department Manager call Whirlpool. He was given the same runaround and told the parts would be mailed to me. He was also given the story about how the malfunction was due to the wire splice being too tight. He then asked to speak to the representatives supervisor and she told him she would not transfer him over to her supervisor. I have forgotten to mention that 2 months prior to this, a Whirlpool water heater (same model) had been returned to my Lowes store within the 30-day purchase window. The unit had caught fire. Since I had had problems with my unit motherboard at this point, I took that unit apart to see what had caused it. The problem started with the motherboard in that unit also. This is unacceptable. Whirlpool obviously has product quality issues.Sometimes bad units are put out. This happens with every brand. But when the same model has such a high failure rate and is known to catch fire, Whirlpools actions are inexcusable. Currently my refrigerator, oven, dishwasher and obviously the water heater are Whirlpools. I will not replace either of these units with a Whirlpool when they reach the end of their operational periods. Also in the future when customers ask me about Whirlpool appliances, I will be sure to tell them just how great Whirlpool is, how reliable they are, how great their customer service is and then quickly usher them over to Samsung, Frigidaire and Electrolux appliances. The department manager that had called Whirlpool for me has shared similar sentiments about future customer recommendations.

They stink. Major issues with most all of these Whirlpool water heaters. I have had issues with 3 different units. I own properties and these are pure junk. Cant find parts and have to pay for shipping on warranty parts! 2 years old units junked, Ridiculous... never buy Whirlpool!

I liked Whirlpool brand. I was excited about the convection option and the warming burner. Plus it was on sale. I really like the AquaLift self-cleaning option but guess what? It does not work well. It is very frustrating!!! I would not recommend buying a Whirlpool oven/range. Low quality construction, features that work poorly, and poor online reviews. Another deal breaker would be poor customer service and repair service. Over, the Whirlpool oven/range is fair. The electric glass top does a good job cooking but keeping the glass top clean is nearly impossible. The oven does a good job baking BUT, the AquaLift self-cleaning does not work. I would recommend that consumers pass on the Whirlpool.

I purchased a Whirlpool washer in 2010. It has started to rust. I called the customer services dept. They told me that there was nothing they could do about it because it was over a year old. I asked to be transferred to a supervisor. She told me the same thing. I told her that its not as if Im looking for a new washer. She said that there was nothing they could do; I had to pay for the repairs myself. I told her, After spending almost $1,000 on a washer, I have to pay for the repairs? She said, Yes, maam. I asked if I could speak to someone over her. She said that she had to take down my name and number and someone would call me back in 24 hrs ... from the management team.She asked for my number and not my name and said someone would be calling back. I told her, How are you going to forward the message without a name? Maam, Im sorry. Whats your name? I doubt if anyone will be calling me back. Whirlpool customer service sucks! They dont know how to treat their customers. Watch out for the warranty. What they call a warranty is not.