Ill be just as responsible as Whirlpool and Nasons has been... I bought my Whirlpool stove less than 2 yrs ago from a reputable business in a nearby community, CROWN POINT, INDIANA! I have had trouble w/ the burner knobs ever since I bought it...just brushing up against them turns them on. Enough gas escapes into the kitchen... I bought knob covers to prevent that (they did NOT work)! So I called the place I bought the stove from and they sent out a repairman...he said there was no fix for it... but that I owed him $69.99 for the service call. And every time I turn the oven on to heat it to bake something you smell gas also... Im almost afraid to use it... 3 nights ago I woke up to the kitchen filled w/ gas...knob covers on but still one was still on a bit... it was a whopping -25 and we had to open windows to clear out the gas... you shouldnt have to check the knobs once youve turned them off. Nor should they come on when you brush by them...when youre not even cooking... Granted I am short but the serviceman said I should move everything I needed to cook w/ closer to me so I didnt have to brush up against the stove... what????? I have cabinets above and all around the stove. What I cant use those cabinets????? Something is terribly wrong w/ the stove and the service... If youre in the market for a new stove, dont buy a Whirlpool and for certain DONT buy anything from NASONS appliances in Crown Point Indiana... They along with whirlpool dont stand behind their product... They told me they never had that complaint before. WRONG, I read it more than once on this site...liars all of them!

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

The space could be laid out a little better. The flimsy shelf is not real stable for foods or ice tray. Where the shelf locks into the side wall is not deep enough to stabilize the shelf itself. The flat indentations in the bottom, where they meet the front, have an edge that makes properly cleaning the freezer a bit difficult.

Updated on 03/15/2020: We bought this eight years ago to replace a 20-year-old Maytag that had finally developed a rust-related leak after serving us faithfully and needing only one almost trivial repair ($10 DIY lid switch replacement) over that period. I have replaced the water pump, the gear case, rotating seal (3 times), the lid switch striker (3 times), and the replacement gear case is making noises indicating incipient bearing failure. In its finite wisdom, Whirlpool decided to make the failure-prone main bearing irreplaceable, which means you have to replace the entire gear case, at a best-case cost of $120 and a worst-case cost of $300, plus labor, unless you do the work yourself, as I do. The secondary issue is mold and a musty odor. The most effective way to eliminate this is to pull the drum (non-trivial, requires a car jack, a 2x4, and a special spanner/wrench) and swab down the inside of the tub with disinfectant. (Been there ... done that three times over 8 years.)Original Review: I am in the process of replacing the bottom seal on my 6-year-old Whirlpool Cabrio (WTW5500XW2) washer. This will be the fourth major repair I have done on it. Fortunately, I can do the work myself and know how to find the best price on parts, but it is still discouraging that a lightly-used washer would have so many problems in such as short time. (It replaced a 20-year-old Maytag that finally rusted out.) Repairs to date: 1) replaced drain pump motor; 2) replaced lid switch; 3) removed basket twice to clean outer tub, due to mold and odors; 4) replaced suspension rods due to excessive spin vibration; 5) out of commission awaiting a new bottom seal. Total cost of parts (labor was on me) is well over $100.

We bought this Gold series refrigerator in 2013.. Less than a year we started having problems with rust on doors. It was so embarrassing people could see this. After that it was like one part after another, the motherboard, the ice on fridge, the ice maker. They changed the same part several times. Now April 2015 they say vapor cooling is not good and they have to put coolant and replace another kit.. Now we have to wait 1 week for that part. Meanwhile our food is going to go bad. Ive been calling for years about this lemon of a fridge. And the last time I spoke to somebody they say buy another fridge while youre waiting on the part to come out. Wow. This is literally driving my family insane.. I cant believe they just expect us to let this happen.. We paid about 2,500 for this lemon of a fridge.. I see so many complaints and youre telling me Whirlpool can get away with this.

I am having the very same problem with my french door stainless steel Whirlpool gold refrigerator. Water pooling in the bottom of freezer, freezing into a solid sheet and then leaking onto the floor. It is less than 2 years old. Apparently, this is a significant defect in this problem seeing how so many people are having the same problem with the same fridge. Has anyone reported to BBB? Im thinking class action lawsuit. Im getting ready to have to repair my kitchen floors as a result of this defect. I will be talking to my brother-in-law attorney about this and will post his response/recommendation. Whirlpool should stand behind their product and make this right.

Whirlpool Gold Freestanding Accu bake Duo FIRE HAZZARD - We bought our house August 2013 and we were SO happy to see the stainless steel appliances and we thought Whirlpool was a good brand that our grandparents stood behind for years (they obviously havent bought from them in 50+ years... times must have changed for the worse). Anyway, I got all moved in and was fixing supper and noticed how REALLY dark and greasy the oven was. I could barely see inside because the coating of grime was so thick that it dimmed the light by being so thick over the glass bulb cover. I immediately thought Wow... the past homeowners were nasty and lazy because they have this nice self-cleaning oven and dont even bother to clean it. I noticed it smelled slightly like it had a gas leak somewhere when it was preheating but it cooked the supper okay that night.Because it was hotter than a jungle in NC in the summer heat of August, I decided to wait until winter to use the self-clean... thought it would warm the house as it got rid of the gunk, right? I kept using the dark coated oven about a total of 25 times and always noticed the faint gas smell at first when it would preheat. I thought maybe it was SO dirty that the oven seal wasnt working right and since it was now November, I figured I should just run the self clean cycle and maybe it would make it run properly as it was REALLY dirty and the igniter or something may actually be clogged. I figured it would probably stink a little at first when it started the cleaning cycle because of the excess build up but it needed cleaning so bad that I cleaned it... The smoke alarms started to go off, we just disconnected them for peace and quiet... Our throats and eyes were burning and it smelled more like plastic burning... FOR HOURS it was horrible! The walls and the Terracotta tile floor were flaming hot!!! The next morning the house actually smelled like it had caught on fire and it stayed that way for weeks!The oven was very clean inside after the cleaning BUT the oven is now totally useless! It will not stay lit. I have never been able to use it again as it will not come up to temperature... just clicks over and over and hisses trying to light. I tried again today and it started LOUDLY hissing like a big open gas pipe was on in there and I got scared and cut it off. THANK GOD it went off!I have been reading similar complaints about Whirlpool Gold ovens for a couple hours now and I am truly scared to use this oven now. After reading the comments of the hundreds of dollars it will take to get it to bake again and how most people STILL had the same reoccurring issues and NO help from Whirlpool... Well I decided to share my experience in hopes that if anyone else is reading this... and I am sorry to say... Well... you are not imagining the problem either. We never read these blogs like this BEFORE we buy or use our appliances, only AFTER something scares the crap out of you and you look for a recall. If I could afford to sue Whirlpool for a replacement then I would. I wish everyone could afford to sue Whirlpool for their unresolved issues that have cost them unnecessary expenses due to the customer loyalty we have had for Whirlpool as we used to be taught You get what you pay for and Do not go with an off brand because those companies go out of business when you need them to repair or service stuff. Am I the only one that was taught this? Times are very hard now and the economy is getting worse and now we have to be screwed by big companies like Whirlpool getting rich off of hardworking people and they do not care enough o help pay for the poor workmanship issues they are making. Shame on you, Whirlpool. I am taking the rest of the day to read reviews on a replacement stove so I can get this ticking time-bomb out of my new home. I too have read enough about the same oven that others have had worse memories than I did. I will not waste anymore of our hard-earned money on Whirlpool ovens. You have to decide what is good for you....

Bought a Whirlpool refrigerator from Best Buy a yr 1/2 ago. Went wrong from delivery and never stopped! There isnt enough room here to specify so Ill try to synopsis this. They screwed up delivery date and then time. Fridge was unbalanced, doors wouldnt close delivery guys didnt know what to do. Tried to fix it and then call their office and were put on hold for over 30 mins. And the Rep was unhelpful and rude to me and then the delivery guys finally got door shut on freezer but Ice maker wouldnt work so they said they would have to have someone Whirlpool to fix it after them talking and being on hold again with their Rep. They were upset and late and felt sorry for me and told me Confidentially That this was not uncommon and they would do what they could to help me.It took many calls, people and conversations (subsequently I found dents, drawers cracked, cracks in back wall) for them to get someone here. When they did the guy was rude and acted like a pre-programmed robot. He said, Show me whats wrong and I did. He stood there and just stared at me and said, I dont see anything wrong. I was shocked! I said, You mean thats supposed to shower the kitchen with crushed ice, etc? He said YES! I said, Ok, please leave my home. I will contact Whirlpool and Best Buy Again. I did and it went on and on and on and to this day theyve done nothing. I have copious notes, dates, names etc. I have also heard many other complaints about both companies and will never do business with either again and will tell anyone and everyone I meet.

We bought a Whirlpool washer (Model # WTW4900BWO) and dryer (#WED4850BW) and within 2 months I was having problems with the washer AND dryer. Every time I washed a load of clothes, the clothes would have some yucky stuff hanging all over it. I called Whirlpool and was told to try setting the washer on 1 Rinse with Softener even though I never use a liquid softener. Their suggestion did solve the problem, but why doesnt a brand-new washer work the way its supposed to? A short time later, my dryer buzzer stopped working and the knob would not advance when set on the Energy Preferred setting. I called Whirlpool again and was told they did not have a service technician in the area where I lived and that it was not likely that one technician would come on the same day to service both machines. I asked why they would sell their products in an area where they were not willing to service them and they said that is the choice of the store that sold it to me. Then they told me there was a service technician available about 40 miles away and they would fax the order to them so they could contact me. The technician who came did look at both machines and was able to determine that the control panel needed replacing on the dryer, but was not able to do anything about the Rinse Option problem on the washer. He suggested that I continue to follow the recommendation of Whirlpool as long as it works. I can do that, but Im not happy that a new machine does not work the way its supposed to. He also recommended NOT using liquid laundry detergent or fabric softener in my washer because it contains animal fat and can build up and cause problems. Nowhere in the manual did it say that. He took the washer apart and showed me how it was already building up under the washer basket. I told the technician that my laundry has had an unpleasant odor to it when it comes out of the washer and even after it is dry. He said that might be because of the small amount of water that is used in the energy saving washer. If these problems cannot be resolved, I consider this washer to be a lemon and hope it will be replaced with a new one. If I had to do it all over again, I would buy a traditional washer. I liked the idea of conserving water, but not if my familys clothes stinks.

We bought this washer on 9/05/09. Recently, it sprung a leak due to a worn out seal that the repairman said would cost more to fix than just getting another washer. You would think this might be cause for distress, but I literally jumped in the air and clicked my heels with joy! This washer has been nothing but a pain. First of all, I have to pre-soak every load before washing or the clothes come out just as dirty as they went in. I would set the timer on my stove to let me know when the 40 min soak cycle ended so I could change it to wash. Then I reset the timer for another 40 minutes. I also learned the hard way, that using any kind of heavy duty setting would turn towels into a pile of yarn. This washer cost $998, and guilt is the only reason I didnt replace it years ago. Ding Dong the washer is DEAD!!!

Whirlpool has been a trusted name for us for many years. The large tub has cut my wash load in half. Large towels to delicates have never been a problem. My washer is going on 12 yrs old and runs like a champ.

I bought a Whirlpool washing machine on 16 Feb 2011. I started having problems with it in June. It was making very loud noises when it was agitating and the clothes were still wet after the spin cycle. I called Nebraska Furniture Mart where I purchased it and they said that after 30 days, I had to call the manufacturer. I called Whirlpool and they sent A&E out to fix it. The technician that came out spent an hour trying to figure out what was wrong with it. When he was gone, I was left with two inches of water on my washroom floor and I had to pull the washer and dryer out myself to wipe it up. He ordered a part that came the next week and a different technician came out to put it in. After looking at the washer, the second technician said that the first technician diagnosed it wrong and he ordered a new transmission for it. About a week later, the transmission arrived at my house and a third technician came to install it. The washer worked for a few days and started acting up again and leaking water. I once again called Whirlpool and they sent yet another technician out. I told Whirlpool that I had lost faith in A&E so they sent All Appliances out. The technician from All Appliances said that it needed a transmission and he would have to order it in. A few days later, he came back to install it. It worked for a few loads. The leaking had stopped but now, it does not spin out the clothes. To make matters worse, it now releases the Downy at the wrong time and I now have blue spots all over my clothes. I have made repeated calls to Whirlpool and talked to two different managers. I asked the first manager for her direct number so I wouldnt have to go through the whole explanation again if I needed to call back. But she gave me her number without her 4-digit extension so, there was no way of finding her again. When I talked to the second manager (by this time, I have lost my patience), I told him my whole story and I told him that Whirlpool has spent $1,000.00 between parts and technician service on a $460.00 machine and it still doesnt work. It is a lemon and I deserve a voucher for the full price to purchase something different.After one and a half hours on the phone, Lukas informed me that the only thing he could do was to send yet another technician to my home. I have lost all faith in Whirlpool and I believe that they do not stand behind their product. They only push you until the warranty has expired! I will never buy another Whirlpool appliance again!

The front of our Whirlpool washing machine started to rust in one place at the bottom within six years. Now it has broken out in three of four places on the front. We are very dissatisfied with machine and will never buy one again.

My father and I both got the Whirlpool Gold gas furnace 3 seasons ago. I can't tell you how happy we both are! Our heating bills plummeted; the unit is quiet and does a fantastic job. I am 50 and I have to admit this is in the top 5 of the best purchases I ever made. For me to take the time to find a place to write a review 3 years later should be testament to how happy I am. Make sure you have it professionally installed! Don't skimp here…this is the key!

Its just a plain refrigerator. No bells and whistles. It could have more space in the bottom and well as a ice machine or ice maker. Nothing special about it. Just a place to keep food. The light in top could be higher so food does not touch it.

Purchased this oven in September 2012. Three months in, we tried to use the self-cleaning feature and blew a thermal link (guessing terminology). Tech came out and got the oven open and that was his determination. Also said he would replace both the front and the rear one because it was pretty common that if one was bad the other would probably follow. Said hed have it within a because he had to order it from the factory. I called a week later because no revisit had been scheduled and found out that the factory also did not have the part and was sending me a new unit. Whirlpool was supposed to call and tell me that and did not. It would be another week. Then a few more days for them to come out and replace it and pick up the original unit.Now I have brand new unit again so we tried the self-cleaner. Same issue. To make a long story short I called again this morning and scheduled yet another service call because the oven is inoperable again after running the self-cleaner. This is the 4th time with the replacement oven. They have replaced the thermal units several times and have replaced the fan.Fortunately, when I complained vehemently about the original unit, Whirlpool gave me a one year extended warranty on the replacement so I am still under warranty, which, if youre dumb enough to buy a Whirlpool after reading this, I would advise paying for. If you already have one and are having similar issues, call Whirlpool and insist they give you one for free because they sell junk.This time I told the nice customer service lady that, since the holidays are over and I can get by without the oven, I am going to run the self-clean right after the tech leaves. When it blows and gets repaired again I am going to repeat the process until they refund my money or send me something that works. Whirlpool apparently doesnt care because in their agreement with their service companies they only have to pay for the first visit. After that they just supply parts. I will keep doing this until I run out of service companies in Denver. Then I am going to pay for another extended warranty when this one ends in September 2014 and continue the process.Wake up Whirlpool!! If these units fail consistently at high altitudes (which every tech that has come out here has mentioned as an issue) then fix the problem or quit selling it in these areas.

I know that appliances are made to be disposable, but throwing away a $40 toaster after 18 months is easier to live with than throwing away a $350-$400 dishwasher. We bought a new dishwasher at Lowes on October 15, 2015. It is now May 11, 2016. The manufacturers warranty was for a year. It has been about a year and half since it was installed. Not very long for an appliance that one would assume would last at least 5-10 years. When we called Whirlpool to see about a repair visit, we were told that the trip to the house would cost $105, and the parts could go as high as $250-$300. So if you weigh the original price to the repair price, having it repaired is not rational, but neither is throwing away a dishwasher thats almost new. Its still clean inside. No soap residue or anything in the tub. In the past, by the time we were in the market for a new dishwasher, our old dishwasher looked like it had been through the war. It just breaks my heart to know that a company is so slipshod at making appliances that they wear out in less than two years. There doesnt seem to be any recourse but to dump a perfectly good, relatively new dishwasher in the landfill. We are leaving a very big footprint by doing this.

I recently renovated my kitchen and was so excited to have a new range. Loved the looks of this one so I bought it. I’ve had it a little over a year now, and am so disappointed. The “stainless” trim around the knob area is peeling and the AquaLift self-clean DOES NOT WORK! After the AquaLift cycle, there was a watery mess in the bottom of the oven which was difficult to clean up. It would have been better if I had cleaned it the conventional way. I’m not sure what to do at this point. The area where the trim peeled off looks awful and is very noticeable. Take my advice and do not buy!

NOT Even a 1 STAR!!! We spent A LOT of money on a Whirlpool Smart wall oven combo. It has only been installed for about 2 hrs. My husband and I have been trying to figure out why all the features on the Whirlpool app aren’t working. Most of our home has smart features and is connected to our phones so it’s not the fact that we aren’t tech savvy. I finally gave up and decided I’ll call customer service line about it tomorrow when they open. It’s Sunday night so every number we call says it’s outside of business hrs. Then excited to turn on the oven for the first time I turn the oven on and the noise that the fan is making is so loud you can’t even talk over it. The oven has been off for 15 min now but the noise continues. 3000.00 for a huge disappointment. Not to mention the thing is HEAVY. So the thought of us having to remove it and replace it with another does NOT make us happy at all. Best Buy or Whirlpool WILL be the ones doing that. For the trouble and money spent that’s the least they can do. Also family is coming into town for the holiday. We made sure to purchase way ahead of time to be sure we had it, installed it and can use it a few times to get the new smell out of it. Very very upset, angry and disappointed. Now it’s been 10 more minutes and the loud broken fan still won’t even turn off. Now we have to shut it off at the breaker. At this point I don’t think we will be even exchanging it for the same product. I knew we should have bought a Samsung!

I am very unhappy with the Whirlpool Cabrio washing machine that I purchased. Dark clothing comes out with lint deposits that will not come off. I have to rewash them at least one more time and then it does not always come out. I dont know if it is because the water level is too low or that it has no lint filter but I will never purchase another Whirlpool product again.

We went out and bought the new front loader washing machine and dryer. Neither one of them works correctly. A service call had to be made the the day we ran the first load. The washing machine only washes errors popping up F8 and E3. On the dryer error code E3 pops up and cannot dry clothes. Worst purchase I have ever made.

I had one of the first Maytag Neptunes. Loved it to pieces but finally had a problem and my beloved repair guy said it was almost 20 years old so to give up and move on. Obviously, cant be without a washer for very long so grabbed this Whirlpool Cabrio Platinum Washer. One of the biggest disappointments ever! Clothes come out streaked and splotched, dont smell very fresh or clean even straight after having been washed, stains dont come out even with pre-treating, have to run everything on heavy duty, whites are getting grayer by the week, and all-around horrid performance.Im ready to give up my Starbucks, start packing my lunches for a couple months, skip whatever treats I have to in order to get back to a quality machine that can actually WASH CLOTHES. I wondered exactly what it was or wasnt doing so I stood over it for half an hour. Initially, it loads up about a gallon of water and then spits it out over the rotating drum of clothes. Then it stops and spins that water out. I suspect the design logic was that it would force that gallon of water thru the clothes taking some dirt out with it. It repeats that stupid process several times. Then it finally gets a few inches of water in the bottom and the vestigial agitator tries to move it around.I watched one hand towel lie on top like a dead weasel, never getting pulled down or pushed out or whatever it was supposed to do to get down among the other items and squish together. Life throws me everything from sick kids spewing body fluids to people coming home reeking of hydraulic and other industrial fluids. When I say clean I mean CLEAN. This piece of junk couldnt satisfactorily process half a dozen dust rags. Neptune, Im coming back with my hat in my hand and a whole new appreciation!

I purchased this Whirlpool Aqualift oven at now bankrupt HH Gregg so my recourse is limited. I loved the look of the slide in range and the salesman raved about the quality of this appliance. First the ceramic top is a nightmare to keep clean, not mentioned at purchase. The Aqualift feature is totally useless. I use my oven on a very limited basis. Putting water in the bottom of oven does absolutely nothing to clean oven and even less on sides and oven door. I spent a substantial amount of money on this so called self clean oven and I am so disappointed in results. It does not get off even a minimum of spots, I would hate to have something actually spill over. Aqualift does not work and then you are advised to not use anything else to clean it, so what now?

My Whirlpool refrigerator, a side by side refrigerator, doesnt stay cold. Now it is 60 inside and my ice is melting but temp says it is 40 in freezer. It is only little over a year old and warranty is no longer good. Hard to believe it didnt last any longer. I paid an expensive price for it. Now I have to have a repair man come and fix it.

I knew I couldnt be the only one with these problems. The reviews confirmed it. I bought my Cabrio washer in 2012. Energy efficient, no agitator to catch on clothes, Great. It took me a while to figure out that the machine was eating my clothes and not cleaning them at all. Oh, they smelled fresh. That HE detergent smells nasty. The machine ate the edges off my good towels, T-shirts, jeans. Brand new underwear (thick elastic) was stretched all the way out and pulled. Normal stains and dirt do not come out even with pretreating. I started running my clothes on the delicate cycle, prewashing stains in a bucket by hand and then putting clothes in mesh bag before running the load. They still came out dirty and ruined. When I run the loads, it still registers as not being that energy efficient on the controls. Id gladly trade it back for my old washer. I feel like I have stepped back in time to a time where you washed everything in a tub or bucket. What a waste of time.

We built a new home at the beach to enjoy our retirement and the builder installed new Whirlpool appliances. As far as we are concerned this was the BIGGEST WASTE OF MONEY WE HAD. Our appliances were under warranty for 1 year as usual and after 14 months things began to break. The latest is the ice maker in the French door fridge. After finding the diagnostics test online I ran the test and determined that the whole ice maker needs replaced. This ridiculous since the fridge is only a little over a year old. We even upgraded the fridge to avoid any problems. After talking to the people in our neighborhood we have come to find out that most people here have had trouble with whirlpool appliances.. I am ready to send these to the junkyard and replace them with a reputable brand (LG) that we owned before and were very happy with.. I dont understand if there is all these problems with Whirlpool products why the technical team doesnt fix the problem... Get parts from the USA NOT CHINA!!! My neighbor just told me he had the repairman at his house 7 times to fix his fridge and finally got a new one. Just got tired of the hassle and expense....

[Model WTW6300WW0, Type 580] A few years ago Whirlpool goofed - they left out the Perma-press cycle on a high-efficiency washing machine model.We noticed the absence of Perma-press (or Casual as it sometimes now called) on the shop floor, and were assured we could arrive at the same results with the dizzying array of buttons that allow the consumer to tailor the cycles to their wash load. It turns out that it doesnt allow this. Buttons are disabled on some of the cycles, thereby preventing recreating a Perma-press cycle. No amount of prodding... Whirlpool has provided me with an override for the combination of a normal wash and a gentle spin that comprise a typical Perma-press cycle.On contacting Whirlpool about the missing cycle, they claim consumers no longer want the Perma-press cycle. Puzzled by this statement, I returned to the showroom floor to see for myself. All the washers have Perma-press cycles. Whirlpool goofed with this model. They left it out. They have not provided a replacement machine for a consumer who blows this whistle on their goof. Among the solutions their customer support DID provide: add softeners to the rinse cycle and add dryer sheets to the dryer to reduce wrinkles [by purchasing a high-efficiency machine, we aimed to reduce waste, not increase it]. Among their invalid suggestions: choose the Casual cycle [there is no Casual cycle setting on this machine]; choose Normal cycle, then set spin speed to low [this machine disables the low speed choice on the Normal cycle]; on this machine the Perma-press cycle is renamed Delicate [Wrong. Delicate only swishes clothes back and forth, not robust enough for business shirt colors and cuffs]; on this machine the Perma-press cycle is renamed Colors [Wrong. Business shirts come out too wrinkled on Colors]. There has been nothing I can do to convince Whirlpool that they produced a lemon in this model [Model WTW6300WW0, Type 580] and should replace it with a normal washing machine. I have tried for years, only for Whirlpool to come to the same conclusion: its the consumers problem now, not theirs.

I have purchased offloading washing machine in 13 Oct. Within three years it has given lot of problems. Every third month we have to call for service and spend lot of money. We had changed drain motor and condenser. Wiring is faulty. Machine will be down many times.

This machine is junk. It does not get clothes clean. I had jeans that I soaked and were fairly clean when I put them into wash and had another pair of jeans with a little dried mud. My whole load came out filthy. I am having to rewash the whole load after hand cleaning the washing machine. I replaced a machine that was 25 years old that did a better job than this piece of junk now sitting on its place.

Whirlpool makes a beautiful product that does not last. I bought model WRX988SIBM in April 2015. Two years later the compressor is bad and no warranty coverage. Do not buy this model. It does not carry the Whirlpool 2-5 year sealed refrigeration warranty. Its amazing that an appliance that retails over $3K only comes with a 1 year sealed refrigeration warranty when Whirlpool offers it on other models. Be sure you know what your warranty coverage is before you buy any Whirlpool product.

Purchased both Cabrio washer (wtw6200sw2) & dyer brand new in 2007 for $1200. Within 4 years the motherboard went out. Whirlpool didnt want to fix it. They said it was past warranty. After many complaints to corporate, they sent someone out to repair it for $496 (they paid). Repairman said these models had motherboards from Japan & Whirlpool was aware of the many issues, but wouldnt do a recall. 2009, the springs went out, 2011 F codes began to appear. Clothes dont get clean; not enough water. 2014 & 2015 DU & DL codes appear. Now I need a new Lid latch assembly. These washing machines are not worth buying. Never again will I buy another Whirlpool!! My mom had an old Kenmore that lasted 20 years and only needed a replacement belt. No more fancy high end washers for me!

I have had the washer for 3 years now and it started to make a loud noise during spin cycle. I made a service call and found out the bearings are damaged. Something that cost this much money should last a lot longer. I have researched on the internet and found this to be the problem for a lot of consumers and would like to see something happen.

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

This piece of junk just broke down not even one year after the purchase. Every singe Whirlpool washing machine has broken one way or another. This one will set the wash time for 57 minutes, and exactly 24 minutes left in the cycler, you hear this big crash and then everything stops. Another dumb thing about this piece of crap is that when the problem happens, the POS keeps the lid locked so that you cant tell what the problem is. What morons would put a lock on the lid? Its not like someones going to take a jacuzzi bath!Restarted the POS again, and exactly 24 minutes left on the wash cycle, there was another crash. Both times, exactly 24 minutes. NEVER BUY FROM WHIRLPOOL!

We bought a Whirlpool gas range about a year and half ago. The oven started giving lighting problems we had to light with a match every once in a while. Then the broiler igniter started giving same problems so I replaced the igniter, still did not work. Then I tried the control panel, still nothing. The igniters were about 45.00 each. The control panel was 250.00. Then I replaced the spark module and it is now working. Some models the spark module dont control oven and broiler but mine does. That was 200.00. The best thing was the part place I was ordering from would exchange the parts that you try and they also can answer questions either online or by phone, Appliancepartspros.com. My oven model # is wfg371lvs3.

Bought a Whirlpool Cabrio washer from Home Depot. It started making noises on the spin cycle 2 months after the purchase. A technician came out and concluded it was a clothes hanger behind the machine making the noise. False. Two days later I tried to wash a load. All the panel lights came on. And then the machine died. No power. The tech came out and tried to run tests but the machine would not respond correctly. Informed it has a bad control. The machine will malfunction even if a button is pressed too long. And then its repairman time again. This machine is poorly designed. No doubt whoever designed the digital control panel did not think about ease of use. The tech has to recalibrate the controls after every failure. Whirlpool and Maytag have put out a bad product and this will be my last.

In 2007, I purchased two 30 gal. Whirlpool Flame Lock water heaters (Model: FG1F3030T3NOV) from Lowes for two different homes that I own. I started having trouble with one of them after about two months. I replaced the thermocouple several times, with each one working only about a month. After that, Lowes replaced the complete burner assembly and that, so far, fixed the problem.Now, the second one has (1 Oct 11) gone out. The local Lowes told me that they are out of the burner assembly for this water heater. I called them this evening and was told that they didnt know when they would have the part, but to call back about every other day to see if they had received the burner assembly for this water heater. They said that it could be from two days to two weeks before they may receive this part!In 2008, I also purchased a 40 gal. Whirlpool Flame Lock water heater (Model: BFG1F4034T3NOV) for my house and no problems so far. In 2007, I even recommended that a friend of mine purchase and install one of these in a home that he owned. He did. I helped him install it and it later had the same problems! I am now needing a water heater for my workshop. What can I buy thats dependable?

My wife and I were gifted a brand new washer (model: WTW7300DW0) and dryer set. We were very excited to try them out as we had just moved into our new home and had been without a W/D for about a week. We ran our first couple of loads and discovered that our clothing was, especially dark colors, covered in white stains. We didnt know what it was so, we did a little research and found out it was most likely soap residue. So, we reduced the amount of soap we were using... and it still happened. We tried every setting available on the touch screen... clothes still came out covered in soap. We eventually called Whirlpool and had a technician come check it out. He ran his tests, said everything was fine, and to use only a teaspoon of soap for every full load of laundry. This didnt sound right to me but we tried it out... stains... still... and I noticed our whites were not getting cleaned very well at all. Sweat stains from undergarments were hardly touched during the wash cycle. After several more phone calls to Whirlpool, were having another technician come out. I just want Whirlpool to take this POS off of our hands and exchange it for something that works. A washing machine that actually washes would be nice.

I bought my new ceramic top electric range/oven with convection, and the aqua-lift cleaning system in spring 2017. The aqualift cleaning function is a joke, so be prepared to be down on your hands and knees scrubbing. Im careful, and Ive not spilled anything yet, but the oven still gets splatters from roasting meats, etc. Id hate to see what Ill have to deal with when I actually let something spill. Today, as I was down on my hands and knees trying to clean it, I noticed that the enamel is chipping off where the oven racks slide in. Great. I have never had an oven where the enamel came off, much less within a year. I am struggling with heart failure, and I am not up to fighting with Whirlpool.

I am completely dissatisfied with the competence and accountability that I have encountered while dealing with Whirlpool Canada. I ordered a Whirlpool Refrigerator in September of 2011. I opted to switch the door swing myself since it is a relatively simple task and of course they charge you extra if they do it for you. Once I had the door installed, the last step was to screw on the handle. The door was missing the threading which allowed the handle to be installed. I contacted Goehmans to set up a service call. They looked at the fridge only to tell me that they needed to order an entire door. A month and a half later I had not been contacted by anyone regarding the whereabouts of the replacement door.Long story short, over four months later and after hours of phone calls recounting the details of the events numerous times to numerous employees, all Whirlpool had to say over and over again was I understand, but unfortunately we do not provide any compensation.” They said that the warranty only covered repairs and not product replacement, which would be fine if it ever broke but they delivered a fridge that was not built correctly in the first place. They took no responsibility for the lack of quality control.After speaking with the supervisor Josh, and insisting that we be compensated for the inconveniences and frustration, he finally agreed to extend the warranty by 3 months. I told him that they should offer a year extension since if they stood behind their product that it wouldnt even cost them a cent. He politely told me that he understood and what email address did I want the extended warranty information to go to and that he would offer only the 3 month warranty. When I received the email, I found out that I had yet another phone call to make in order to engage the extra 3 month warranty.I am extremely frustrated with the level of service and I feel as though they school their employees to be therapists that offer no solutions. They were all very willing to listen and offer a sympathetic ear, tell you that they understand but not to take action or offer a solution. They seemed to think that it was acceptable that I pay them full price for a fridge but not deliver the full appliance for a projected 6-8 months. In my book and to most consumers, this is not acceptable. When I pay full price for a product, I feel that a full product should be delivered to me in working order. Whirlpool got their money and the special order door seems to be at the low end of their priority list. How else can they justify a 6-8 month wait for part replacement?Somebody please sell Josh a car with no stereo system, make him pay for the option and see if he if he thinks waiting 6-8 months for it is acceptable. Oh yeah, and waste 6-10 hours of his personal time trying find out where the heck his stereo system is then tell him how much you understand. I guess I can stroke Whirlpool off as a brand of appliance for any future purchases.

Less than 2 years after we purchased our whirlpool dishwasher, the rack started to rust. Now the tines are so soft they fall off. The last time we bought a dishwasher the Same thing happened, but after 15 years! They dont even have an option for that to be under warranty so it tells me they dont stand by their product. I will never buy whirlpool again.

I thought the new AquaLift cleaning would be the greatest. Boy, was I disappointed -- no thoroughly disgusted and very angry -- when I tried to use the self cleaning oven. I had cooked a prime rib roast and a lot of grease had spattered inside the oven. I wiped away the excess and did a cleaning cycle -- what a joke! There was still grease running down the door and walls. Nothing was changed after two cleaning cycles. Now I have to crawl inside the oven and scrub it manually. I was always pleased with the old self cleaning ovens which only left some ash and a little bit to clean up. The AquaLift technology doesnt work at all, didnt Whirlpool test it prior to selling it to the public? They will surely lose my business and I hope a lot of other peoples business as well. This technology was a huge mistake!!

On 5/3/16 I purchased an Amana high-efficiency, low water, top loading washer. What a joke, it is a piece of junk. There is no water so clothes dont come clean, and if you leave money in the pockets no worries. As it will be right there after the clothes are washed and dried (got matching dyer also). They dont even smell clean after two washing. And now you are to purchase a cleaner to clean your washing machine. This is truly not an efficient machine in any way.

The microwave was easy to install above the stove and it has the exhaust fan conveniently hidden out of site underneath it. The cost was very low and it is not complicated to set up and use. I also like the fact of not having countertop space taken up by having the microwave sitting on it.

I purchased the top-of-the-line Whirlpool Cabrio washer and dryer. My washer is 6 years old and will not complete a wash cycle. According to the repairman, the drive shaft is stuck and it will cost $500.00 to repair it. When speaking with Whirlpool, their suggestion was to buy a new one and get an extended warranty. This company is a total disappointment.

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

This thing will not bake correctly, leaves pie bottoms raw, yes we use convection. We have tried everything to get it to bake correctly but to no avail. Top and control panel get very hot when only using oven. This thing is junk, taking it back to Lowes.

I used the Whirlpool website contact form, and described an issue I have with the Cabrio washing machine. When the form is submitted, it states that the company will respond in three business days. Two weeks later, after no response, I submitted a second contact form. It has been five days, and I still have not received a response.

My family purchased a Whirlpool Cabrio washing machine approximately 4 years ago. The first two years were fine. I had no issues out of the machine at all. The last two years (just as my warranty expired) have been terrible. It was serviced twice just before the warranty was up and my husband has serviced it twice since. On two separate occasions, the bearings have worn-out and the bottom seal leaks water all over my floors. I would never recommend one of these machines to anyone!

In 2012 we purchased a Whirlpool Nu40T61-403 water heater from Lowes that I installed due to us not being able to afford a plumber. I have since become a plumber. This morning while attempting to shower I noticed that the water was lukewarm with the shower valve turned all the way to hot. I got dressed and inspected the heater. I began to diagnose the problem. Pilot was out and Gas control valve signal light was off. Lit the pilot and it appeared to be functioning normally. My first thought was the thermopile had failed but seeing the pilot stayed lit this proved to not be the case. I was extremely relieved at that point. Turned the temperature control knob to high and the burner kicked on. At first it appeared to be functioning fine. But within about 20 seconds I began to hear detonations within the sealed combustion chamber.

We have had our Whirlpool range for probably 20 years. We have never had any issues or problems with it. Our washer and dryer are both Whirlpool too. I would recommend this brand 100%! I think this is the brand that my mom always had too. Their products are very well made and last forever (it seems like they do!).

I purchased a Fridge/Freezer just over 4 years ago. It was an expensive one. The gas is gone and they cannot re-gas it. If I was told this when I was purchasing it I certainly would not have spent this money. I rang the concessional team. They would give me nothing towards a replacement as they had not one in stock, POOR Service for a big company. I am in business and this is not the way I would treat my customers. This has certainly turned me away from purchasing Whirlpool Products, despite having a industrial washing machine and Dryer. For the record, I had 2 servicemen to check it and they were most pleasant. It was beyond repair.

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

Hot water heater model #0833T402747 purchased late 2008 - Several service calls had to be made to a plumber, due to this unit not working. The door assembly was shipped to me by Whirlpool. I had to pay again for the plumber to install this part. Hes been here 3-4 times since I bought the unit. Last Wednesday, May 2, 2012, no hot water again. The same plumber came out and said the door assembly had again gone bad. Whirlpool was contacted on Thursday morning and would not agree to do anything. They were given my plumbers name and number and I never heard back from them. I contacted Lowes in Acworth, GA and they agreed to replace the hot water heater. So now Im forced to pay for another install. I requested that Whirlpool pay this expense, and their representative, **, said no. I intend to sue them for all monies spent on this lemon and due to this lemon, I will never buy another Whirlpool product of any kind. I have told family and friends and theyve agreed that due to the bad product and worse customer service, they will also stay away from purchasing anything made by this company. Whirlpool certainly wont be hurt by me and me alone. But Ill make sure that anyone I run into at Lowes or anywhere else is even looking at a Whirlpool product will get an earful from me. This is the type of customer service that consumers dont have to put up with anymore. There are many resources on the internet to get the word out and I intend to spend a great deal of my time doing just that.

Whirlpool microwave oven a few months old stopped working. Customer service center not helpful with prolonged holds (>30 minutes), no response to email, and amazingly no response to live chat. The 800 number was busy at one point for over an hour. When I finally did get thru, there was no coordination with local repair men, and a factory delay on the parts. I am going on 6 weeks without a functioning microwave and 3 kids at home. Thanks Whirlpool.

We just purchased a new fridge - September 2021 -- Whirlpool side by side. Why is just okay? It is a loud refrigerator. A roaring sound is pretty constant. The ice tray in the door has no recessed tray ... so water and melting ice just follow down the front of the door and onto the floor. Two days after purchase we went back to Lowes to return this fridge ... but all the other refrigerators do not have a recessed ice tray. And since they are not plugged in ... who knows if they roar.

Whirlpool Gold Series Dishwasher - I wish I had discovered this website BEFORE I bought this piece of trash last year to replace our antique Maytag that ran like a champ for 10 years. But after 10 year the gaskets wore out and it started leaking. Even at ten years old that Maytag cleaned and dried better than this brand new Whirlpool. My complaints are the same as everybody else here. Doesnt clean even slightly soiled dishes and then it doesnt dry any of the silverware, or plastic pieces like measuring cups and tupperware. All are totally wet and need to be hand dried. So, why am I cleaning the dishes beforehand and drying them after??? The only good thing I can say about this unit, is that it is quiet. But, as my husband said, so is a brick, and a brick would be just about as good at washing and drying our dishes. Buyers Beware!!! This is a terrible product. Turned me against Whirlpool appliances forever.

Purchased the American Made Whirlpool in Oct. 2020. There is plenty of room and there are only 2 adults in the home. It is a basic no frills refrigerator. We do not even need the ice maker that it has. Would purchase this again. The only negative is it makes weird gurgling sounds on occasion.

We purchased a gas range (Whirlpool AccuBake model # mfgxfg361lvt1 serial ry1810956) a few years ago and have been very unhappy with the gray grids that it came with. We wrote to you about how we should clean them and you recommended heavy-duty degreaser, pin31552a and gas grate & grill cleaner, pin3167a, which we purchased. Neither worked, even with heavy elbow grease. We are very upset. We have purchased Whirlpool products all of our life and would like an answer or some type of explanation. If possible, can we get the grids in black? We try our best to keep these things clean and this is a very bad patten.

I am posting to help anyone else avoid the purchase of this machine! The lid has cracked and now warped into a position where it wont stay down. Obviously a washer will not work without being in the locked position, so we have to put several heavy things on top of it just to run a load of laundry. This is not what we expect out of a washer that we paid $900 for only two years ago!!!! We contacted Whirlpool and they offered to fix it for $350. REALLY??? I SHOULD NOT have to pour money into a washer this expensive after two years!!!! I am so disappointed in Whirlpool, this was the entire reason we purchased Whirlpool products, to avoid stress of broken appliances. We wanted reliability for our busy family and instead we bought into more stress.

New whirlpool washing machine 2016 - This washer is supposed to be smart, but it NEVER fills up with water! I always have to fill a bucket with water and throw it in the washing machine. My clothes do not come out smelling fresh and its not the detergent to blame, its the washer! Im so disappointed with this product. Whirlpool should stop making products.

I have had too many problems with the thermocouple beginning about two years after I purchased the water heater in 2003. Whirlpool keeps replacing the thermocouple, but I have to pay for the plumber to come out and repair the unit. This runs me about $180 each time. The thermocouple has burned out three times since September of this year. The plumber didnt charge me anything the second time it went out. But it went out for the 3rd time today and he recommended that I replace the unit. Of course, it is out of warranty and Whirlpool was happy to tell me that I could purchase a new thermocouple at my own expense from them. I have paid for this water heater three times over with repairs. Whirlpool knows that there is a defect with the design of the water heater. There is no way that a regular consumer can get inside the water heater to clean it. I will never purchase any Whirlpool products ever! I advise anyone reading this to follow suit.

We purchased a brand new stainless steel refrigerator in 2013. Our 2 year refrigerator stopped producing ice and the freezer stopped working as well. We called Whirlpool customer service and they said they could not help due to 1 year manufacturer warranty only. We called another company (SoBellas) that charged us $85 to tell us that it is the seal system which should be covered up to 5 years by Whirlpool. The man showed me the Whirlpool refrigerator warranty on Google which states the sealed refrigeration parts are covered up to 5 years. There was no specific model numbers listed which gave me the impression this was a standard warranty for all Whirlpool refrigerators. I explained the situation to Whirlpool customer service including the 5 year warranty that is found on Google for everyone to see. I was told that our refrigerator model number did not qualify for that specific warranty. We ended up having to buy extended warranty for $350 on top of the $85 we already spent. This started July 24, we had to wait until August 10 for Whirlpools warranty company to see us. They checked it and said they had to order parts but he supposedly tweaked it to make our fridge run better.... It made it worse and it ended up completely breaking down. We had to buy ice chest and waited until Thursday August 27th for them to finally come back with parts and fix the refrigerator. I took time off from work once again due to our time slot being between 3 and 5 but the guy didnt even show up until 7:30. I could have worked my normal hours instead of taking more time off! The guy never once called to inform us that he was running late. We kept calling the company to make sure we werent forgotten. The guy told us that everything should be working within 20 hours or so, by Friday our freezer was still not working and no ice either, back to square one! I called Whirlpool customer service once again to explain the situation, nothing could be done. The next available time for them to come back out is September 17 for them to come look at our refrigerator. We have been stuck without ice and a freezer, buying food every other day waiting for our brand new, horrible Whirlpool refrigerator to be fixed. Will never ever buy Whirlpool brand again! Actually, we purchased all brand new Whirlpool appliances... Good luck to us!!!!!

Do not purchase (Whirlpool products). Discuss guarantees with salespeople when purchasing! They are total sham and in fact borderline fraud! Purchased $5,000 dollar KitchenAid fridge only to have it breakdown after only 8 months. What they dont tell you is instead of recalling a product they give their repair personnel whats called a notice which means they know there are issues with their products!After much discussion and trying to return the product to no avail, I was told very adamantly my fridge would need to break down another additional 2 times before my fridge would be replaced with a new fridge. Forget about the cost of your food inside the fridge, they dont care! Just beware that their warranties and parts and labour are a complete and utter joke! My advice after much research if you can afford it buy Miele or Subzero product. Its more expensive but a lot less headaches in the long run! Ive eaten the cost of my KitchenAid appliance and went with a Subzero fridge. Dont believe the higher pressure sales pitch from salesman. Youre best to call a repairman and ask what hes fixing more often than not and 9/10 times he will tell you Whirlpool product! Customer service is a complete circus and gong show. Youll get further ahead talking to a donkey!!! Buyer beware! Whirlpool Canada/USA is a joke!!! Dont say I didnt warn ya!!!

This product is just DISAPPOINTING. The gas knobs got stuck TWICE IN 13 months only! The range is NEW! The first time 3 out of the 4 knobs broke, this time only one. It would not turn off, so we are forced to climb on the counter and turn the gas off every time we are finished cooking and turn it on again. The company wont be able to send us anybody till next week, which will force us to go on like this for NINE days plus, of course, the time it will take to order the parts needed.There is not even a back up emergency service, which should be in place since we are dealing with GAS! I have heard complaints about this product in this area: in my opinion the range should be recalled. Of course, the representatives one talks to are all trained to keep calm and reply the usual things: Oh, I am sorry etc. but the bottom line is that neither the product nor the customer service are good (the first customer service person was not very friendly either). I highly recommend that you AVOID this range if you are considering buying a gas one with double oven.

I bought a Whirlpool dishwasher in 2008 from Best Buy and purchased the extended warranty through Best Buy. First of all, my complaint is not with Best Buy (model # DU1145XTPBA). I have had nothing but trouble with the unit not filling with water, being noisy, and other problems. And then, my intelligence is insulted by these independent contractors, who are supposed to be appliance repair specialists. I found that far from the truth in most cases. They have a list of patented things that the consumer is doing wrong: not having a hot water heater next to the unit, using too much detergent, not loading it properly, and on and on. They must think we are idiots. I always would run the water from the sink till it got hot before filling. And I am a miser so I use less detergent than what the manufacturer or the detergent package says. Anyway to make a long tale short, it started leaking last week, so I assumed the door seal or some other such thing. But lo and behold, the door is rotted out at the bottom. The black finish has bubbled up and the metal is actually rotting away. I am from up north and it looks like my old Chevy 2 Nova rotted out. I called Whirlpool and spoke with several people and supposedly someone in management. They were, of course, sympathetic but offered no assistance or explanation. They offered to send a factory authorized repairman to replace the door at more than the cost of a new dishwasher. Are we that stupid? They never offered me a voucher for a discount on a new unit, which I am going to have to buy. I would not have accepted it anyway, as my last few experiences with Whirlpool have been dreadful. I will never buy another Whirlpool anything. The name used to stand for a quality product that you could depend on. But now it is like most things are offered to the consumer in this throw away society. And as long as we keep buying inferior products and only expecting them to last a few years, I am afraid that is what we will continue to get. Be vocal and let them know how you feel, even though they are probably yawning on the other side of the phone. They are without compassion and could not care any less. They are just looking for a paycheck and have probably heard a hundred complaints like mine, so its water off the proverbial ducks back. But when its their own job in jeopardy, perhaps they will start passing on these complaints to someone who will be willing to listen. Its a very bad experience and I will never buy Whirlpool again.

This is the only time in my life when I have seen a Microwave behave so badly (and one that is relatively expensive). The microwave is defective out of the box. Seems like there is a comWhirlpool MWA269 (4You)mon trend with Whirlpool products and cheap Chinese boards. The microwave never stops working once the timer runs out. It will just keep going. Model is Whirlpool MWA269 (4You).

Purchased a Whirlpool Cabrio 4 years ago. It worked fine until last October when I had to call a Repair Service as all the Digital Controls would not work. It was the Digital Board had to be replaced at a cost of $ 315.00. That was October 2016 and in October of this year 2017 it started doing the same thing again. I call the Repair Service and they told me not to waste any more money on this machine as it is a piece of junk. I guess he was right as when I read all the bad reviews it got today, I realize I will be better off to buy another machine. It will not be a Whirlpool product. I purchased a Sears Kenmore Washer & Dryer back in 1995 and the washer lasted 20 years and I still have the dryer. This is what you refer to as a good product.

I bought a Whirlpool washing machine, model WTW4855HW, and was I ever shocked at how noisy it was. The wash cycle had a grinding noise that was just too much. After 2 loads I sent it back and didnt regret having to pay the restocking fee. I just couldnt believe that with all the technology we have today, that they couldnt build a quiet machine. Im an engineer so I know there are methods through gearing, belts, soundproofing, etc, to produce a quiet machine. Remember the dishwasher of days gone by. You couldnt watch TV with the dishwasher going. Nowadays, you can stand in the kitchen and have a nice conversation with it running. The technology exists. As a matter of a fact, my old Maytag that finally went bad after 10 years was fairly quiet. So, if you dont have your washing machine in the garage or basement room where you can close the door, dont buy this machine! Bruce in Portland

Very loud when in spin cycle, tub leaking out of the bottom. Bearing is shot. Only lasted about 3 years. It also knots up the laundry, does not remove dirt from soiled clothing.

Re: wdf7payw6. I purchased this unit last February. It has never washed properly. In the last month 2 separate warranty service reps have been out. The first one told me that I have not been doing a good enough job of prewashing the dishes so the arms were clogged. While cleaning them, he broke the top arm. When he came back to replace the top arm, he added that the dishes were not drying because I didnt use enough jet dry so I would have to dry by hand, and that the arms were clogging because I didnt prewash well enough. I told him to leave and never come back. I called customer service and they sent out a new company.The rep today told me that even on time delay or overnight settings I must run the hot water prior to starting the unit. And that since the water wasnt hot enough; the undissolved detergent was clogging the spray arms. This was confirmed by your phone support person who told me that for best results thats what I had to do. The result I want is for the thing to wash dishes. It doesnt do that. The current rep ordered a heater, motor pump and spray arms. My previous dishwasher operated perfectly (until the pump failed) for the 18 years I have lived in this house plus however long it was here before I moved in. I will never buy a Whirlpool product or anything built by subsidiaries or parent AGAIN.

Bought a model wdt730pahz in Nov 2017. Up until recently it ran fine and we were very happy. Some folks have reported that the soap dispenser door gets stuck. Same here. In our case we found, when using those detergent pods, to make sure that they are pushed all the way into the dispenser before you close the lid, or the lid jams. Other than that, the dishwasher got the dishes nice and clean. However, after just two years of using it maybe 3 times a week (there are only 2 of us) the motor died. Youd think a new motor ought to survive at least 500 cycles. Anyway, parts and labor was quoted at nearly $400. Debating whether to fix or replace the dishwasher. Might try ordering a motor and pump and replacing it myself.

So, I have a house full of relatives from out of town staying over and as luck would have it, my Whirlpool water heater (model # BFG1F4033T3NOV) which I had installed 15 months ago, decided to stop working. The pilot light went out and would not stay lit no matter how long I held the red restart button. I called Whirlpool customer service and was informed straight away that their computer system was down and they wouldnt be able to order parts if I needed them (great start right?). I explained to the woman on the phone what my issue was and also told her that after searching online, Ive found that this is a common failure with these hot water heaters that Lowes sells where the thermal couple is defective and needs to be replaced. She began to inform me that before any parts was ordered (which she couldnt do because the computers were down), I would have to clean the vent openings on the bottom of the HW heater. No big deal. Then, Id have to have my gas line pressure verified by my gas company (what?). If both were found to be fine, Id have to confirm that my flue is at least three feet above my roof line before they would send me parts to repair my unit. This is about where I lost my mind.I run the RMA/Customer service department in my company and if anyone has issues with our products, we ship first and ask questions later. How can a company with known defective products give their customers the runaround and basically tell them that they are screwed until they can take off time from work for a gas co. to come to their home and will also have to have flue replaced before theyll warranty their product?! Whirlpool should be ashamed of themselves and Lowes should distance themselves from such a crappy company with substandard products and shoddy warranty practices. Ill never buy another Whirlpool product as long as I live and will warn anyone away from this company.

The gas water heater that we purchased has been a headache. Pilot went out several times. When we contacted Customer service they informed us that we would have to have a new kit put on it. We ordered that and it worked a while and then we started having the same problem. Just recently we had to purchase another part and once again we have cold water. Fed up.

Whirlpool model WRV986FDEM Purchased May 31, 2017 from Lowes. Cost: 2,638.10 including 229.97 for the 5 year extended warranty. We’ve experienced four failures in the nearly four years we’ve owned this lemon. The first failure occurred within the one year manufacturer’s warranty period. The three failures since then have been fairly close together. Control boards and mechanical parts have been replaced. We are now waiting for a “made to order” part, with no scheduled delivery date. When I pressed Lowe’s on the reliability of this fridge, I was told that if four failures occur during the extended warranty period, they would give us a replacement. Considering the delays in repairs and frequency of failures, this is unacceptable. Do Lowes and Whirlpool expect their customers to just suck it up and do without a refrigerator for months while we wait? The warranty is worthless without prompt problem resolution. Whatever happened to real customer service?

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

I have purchased many Whirlpool ranges for my apartment buildings that I own and operate. They never give me a problem with operation or length of service. I only have to replace them when a tenant does something dastardly to them. My husband and I remodeled our kitchen and we purchased one for our kitchen too!

Cabrio Washer - We were getting unbalanced load messages and the washer would stop. I called in a serviceman and he said it wasnt worth fixing. It would be cheaper to buy a new one. This washer is only 5 years old.

I have a washer, dryer, dishwasher, hood vent, stove top, and oven, all Whirlpool. I cant say enough how pleased I am with this product. My old washer and dryer was over 23 years old when I needed to replace them. Thank you Whirlpool for making such a quality product.

Have had this Whirlpool for 17 years at least. Only issue we’ve had with it was the ice maker that went out after about 14 years. There is plenty of space in the door. A place that holds cans, 2 shelves that go across the door, a small shelf and a butter shelf with a lid over it. Nice looking too.

I have had two Gold Series dishwashers before but the model number I used had been discontinued so I purchased the W10491035A about a year ago in 2013. It has to be the worst dishwashers I have ever had and we have used them for forty years. Its loud. It won’t dry the dishes, and unless you wash I dont mean rinse, most of dishes are not clean, and that is with the recommended detergent. Whatever you do I would suggest not buying this dishwasher. I dont even know why they would offer a machine such as this.

I just purchased a new Whirlpool 6th Sense hot water tank #333570. This unit is a piece of garbage. Whirlpool should be ashamed at the quality of product they make. This unit came with a bent temperature and pressure relief valve, which required a piece of copper tubing to be bent awkwardly just to remedy the situation. Also, the control box is set at 12 (most other brands are 14, which is common), forcing the gas lines to be re-piped (very expensive). This unit also is extremely noisy, runs really, really hot and is not energy-efficient at all. Shame on me for not researching this product more closely. If youre buying a new hot water tank, steer clear of Whirlpool products.

If you come across any problem or issue with washing machine, the service person will come and will have a typical vouge glance of the washing machine.. and the inner bearing problem etc. He will arrange a call with his boss.. who also tells the same thing… and collects Rs 450/- as visiting charges and goes. They ask you to bring the Washing machine to their showroom... on account of repair they do all nonsense and do replace some parts which are not at all required...*** Instead of going to the show room first, if you take second opinion from any local repair technician... you will be shocked to know that hardly it is very minimum problem like loose connection, biting of wires by rats or other problem which would just resolved in front of us..But certainly not the Big issue as these show room service mafia does.. I have encountered the same brought the same to the notice of the Care Manager Mr.**.. But no proper answer... One should understand that there is big mafia kind of activity just betraying the customers.. Please beware of the frauds of the Whirlpool Washing machine Servicing Team..

Why do I have to select a star? This product deserves none. My experience with a brand new washer has been horrible. I purchased the washer/dryer Whirlpool set from Lowes on 7/1/17. The washer does not agitate and it makes a zooming noise for hours, I have to eventually shut it off and take my clothes to the laundromat. Technicians have come out 4-5 times to “fix” it and replace parts and it is still not working. I called Whirlpool today again and they want to send a technician out again. I told them I cant keep missing work to wait for a technician which is costing me money. But they don’t care. They should be ashamed of selling these manufacturer defected products and then simply refuse to take them back. I wasted around $1700/set on their defected washer and I hope they make it last as they will not sell another product it depends on me purchasing it.I am livid to see how cowardly these big corporations get away with treating the little guy so poorly. But, that is ok, Im in tears right now as I lost my hard earn money and will now have to buy a new washer/dryer set as yours simply don’t work. You just want to continue doing patchwork instead of taking the appliance back and researching what you did wrong to avoid selling these defected products to consumers. Very unfortunate. So if you are reading this review, please don’t buy their products. And big stores like Lowes and HD should stop selling this brand. I’m more angry at the way I’ve been treated by Whirlpool. Rita the resolution specialist made it sound like its my fault the machine wont work. Here is their # 1800-253-1301. If you want to ask any questions about their repair warranty.

On the 10-05-05, I purchased a Whirlpool natural gas water heater from Lows Orem. The unit has a 9 years warranty agreement. Lows sales S0178JC3 647605; cost $378. Model number FG1H5040T3. Serial number 0515140765. Following installation, the unit has failed repeatedly. Since keeping records of the failures, the unit failed either by the gas control valve or the thermocouple on December 2011, November 2011, April 2010, February 2009, and April 2008. Whirlpool has at all times supplied the parts but denied that the parts are technically faulted. Whirlpool has further rejected all requests to refund me for defective product. The major consequences have been an unreliable water heater. There were periods without hot water. Time was spent involving undertaking repairs.

I cannot adequately express my dissatisfaction with the Cabrio washer and dryer that I purchased couple years ago. I will never buy a Whirlpool product again. That includes Maytag; Kenmore; or Amana products. I have had nothing but problems from the start. The washer sounds like jet engine taking off in the spin cycle. I found out the washer needs new tub bearings ~ $200. The washer is tearing up towels during the wash cycle not sure what the cause is.My washer will only wash clothes in certain cycles (bulk). I keep getting error codes in normal or other cycles. The washer takes long time to fill so it times out during fill cycle. I replaced fill lines and checked for blockage, everything was clear. The washer probably needs either new motherboard or water inlet valve. Not sure which, maybe both? It is impossible to wash a load of clothes without getting the UL unbalanced load indicator. I also have problems balancing the load. I have taken wet clothes out and put them back in with no luck. It takes hours for a load to finally wash.The dryer has had its problems. I just replaced the belt tensioner on the dryer because it was making a terrible screeching sound. The noise was very annoying. I am very disappointed with quality of Whirlpool products. However, don’t worry about improving customer relations because I will never buy a Whirlpool product again. P. S. How come you have not issued product recall? There are 1,000s of similar complaints concerning the Cabrio washer. Frustrated customer.

We bought a Whirlpool Cabrio in April 2012 and in July 2012, it started giving problems. It wouldnt start. It started humming. We heard money-like jingling noises. It stopped spinning and rinsing clothes. I called for service. No luck with that. So in order to wash, I had to drag the washer to the back door (which ripped up my new floors) hang hose outside for it to finish the load. Well a few months later, that didnt work so the assistant where it was purchased told us to cut the pipe down in the wall. Now we have a big hole in the wall. My floors are ruined and we are out getting another washer. This one is not even a year old. That was a $750 loss.

I have a rental home and my residence, I have purchased a fridge for BOTH places. Within 1.5 years, both of the fridges shelving cracked. Customer service will not do anything to remedy this. It is a known issue with his model of appliance. There are numerous complaints and they DO NOT stand behind heir product. NEVER BUY WHIRLPOOL.

I was having trouble with our Whirlpool water heater and thought that wed have to shell out and buy a whole new one. Chris saw my complaint and helped me find the right replacement kit at a minimal cost, as my unit was out of warranty. He even took the extra step and overnighted the parts for us at no extra cost. I was extremely impressed with Chris professionalism and customer support skills.

Just cleaning the outside of our piece of ** oven. Must have hit either the on or off button to lock because the damn thing locked. Tried unplugging it, pushing all the buttons suggested on these websites, etc. Hell, even tried to call Whirlpool, where I just talked to a computer. Lesson learned: Whirlpool wont get our business again. Period.

My 79 year old grandmother hasnt used her Whirlpool washer in 5 months because of defects that Whirlpool USA thinks they are going to fix. Really??? How long is she going to go without being able to use her washer that she bought from your company? Is it going to take a year? 5 months!!!! I should be billing you for all of the out service of laundry we are having to pay for because of this inconvenience. I have never experienced worse customer service and more of a waste of my time and my dad’s time. I hate posting this but the only other option is therapy for my family from dealing with this insane issue.

I purchased a Whirlpool refrigerator in 2012 and now it does not work and Whirlpool says a 1300.00 refrigerator only has a one year warranty. Please do not purchase a Whirlpool brand because they do not live up to their brand name.

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.

We purchased our Whirlpool Refrigerator, oven, and microwave a little more than a year ago. Not a single negative event with any of these products and my wife and I wholeheartedly recommend Whirlpool for operation and last ability, unlike the products we replaced them with.

In 2008, I purchased the 40-gal. Whirlpool electric water heater to replace the original unit in my home that had lasted 14 years without issue until it died of old age. After about 2 1/5 years, it died and I was given authorization to return it to Lowes at my insistence. Now after another 2 1/5 years, this one has died. So far, I have replaced both elements, lost a days work, missed out on a date because I could not take a shower and now Im told I have to replace the electrical box on top which wont get here until Monday. Its Saturday and I havent been able to take a shower in my home for 5 days now.The first CSR (Crystal) I spoke with implied that since I had 2 consecutive failures, this was a site problem, not a product problem. Theres nothing special about my site, and my old unit made it 14 years with zero repairs. I would argue that since both of the units only lasted 2 1/5 years, that the product is substandard. I asked to speak to a manager but was told no because they were all busy (no doubt) and her demeanor was unapologetic and unsympathetic. The second CSR (Nick) I spoke with was very nice and at least sympathetic. That goes a long way in customer service, but I was still not allowed to speak with a manager.I am going to try and repair it one more time, but I have zero confidence in Whirlpool and would never buy another Whirlpool product of any sort again. If I get it working, and after all Ive read here I doubt that I will, I will only be using it for the time it takes to get a replacement of another brand. This was my first experience with a Whirlpool product and you can be sure it will absolutely be my last.

I bought a new washer and dryer 2 years ago, it was built by Whirlpool under the Kenmore name plate. In the first two weeks we had them come and service it as it was very loud in spin mode. The serviceman said they were all like that. Now, two years later, it is so loud you cannot even carry on a conversation while in the spin mode. Called for service again. After two minutes he says, You better buy a new washer, this one will cost over $800 to fix. Never will buy another Whirlpool appliance or Kenmore again. Buyer beware!

I purchased a washer 6 months ago and it was starting by itself so I called to get a technician out and it took them 3 days to tell me that they did not service in our area. Long story short I was out of a washer for 2 weeks talking back & forth with Whirlpool which was absolutely a nightmare. Kept me on hold forever and hung up on me several times so they didnt have to deal with the situation. Absolutely no customer service at all. When it came down to it they were going to issue me a new washing machine and I had to go to the store to get it and when I got to the store they told me I had a $415.00 credit to spend. Thats less than what I had paid for the washing machine and then I am having to spend an extra $200.00 out of pocket to get another washing machine.My warning to you is not to purchase any Whirlpool appliances unless you want to go thru pure hell. These people do not care about anyone after the product is sold. Their customer service sucks, their appliances suck and Whirlpool just sucks all the way around!! Worst experience I have ever had and I hope they never sell another appliance again!!

My WTW4900BWO failed after about 2 1/2 years. Out of warranty, but I called Whirlpool Customer Service and was initially delighted that they offered to sell me a repair warranty that would cover the repair of my broken transmission. Was told that through AIG Insurance, I would have a repairman at the house tomorrow to repair the washer. A few hours later, their contracted local repair service called to try to push appointment back a day but I refused since I was told my washer would be repaired tomorrow. They showed up the next day in a old faded van, diagnosed the problem and then told me they would have to get authorization and come back in 3-4 days. A couple of days later I received a voice mail from AIG saying that since the cost of repair was more than the cost of the premium, they were canceling my policy & would refund my money. So a week later I still had a broken machine and no solution other than buying a new one or paying the cost of a new one to repair. Moral of the story: Whirlpool builds unreliable washing machines (and water softeners) and their customer service will promise you a repair that may not happen. Dont buy Whirlpool, but if you feel compelled, you better buy an extended warranty and cross your fingers. That said, we always had purchased GE appliances and never had a problem.

This Whirlpool refrigerator/freezer Model W10314956B was purchased from Lowes on June 29, 2012. Recently noticed rust appearing under ice/water dispenser tray. Requested warranty service, but was told the problem was considered DUE TO WEAR & TEAR! TOTAL COP-OUT! There are NO MOVING PARTS in this area; how can there be WEAR and TEAR? To my mind, this can only be charged as SHODDY MANUFACTURING or INADEQUATE QUALITY CONTROL by the manufacturer.This appliance is only 6 1/2 years old! Consumers expect refrigerators to last much longer than that. The only possible cause for this problem is as stated above: poor quality control by the manufacturing plant, and I completely discount being told the problem was due to WEAR and TEAR! I will think long and hard before I ever even CONSIDER purchasing another Whirlpool product, and maybe YOU SHOULD TOO!One issue that keeps gnawing at me is HOW, since this is supposed to be a STAINLESS STEEL refrigerator, can it rust? The best answer I found on Google was that its likely due to insufficient chromium in the mixture of metals used to make stainless steel. To me this continues to point to shoddy workmanship at the manufacturing plant. I have pictures of the problem, but for some reason Im unable to copy them to this complaint. Probably because Whirlpool is afraid of pictures that confirm their shoddy craftsmanship!

We have owned refrigerators for over 40 years. Never had one as bad as this. Three ice maker replacements lasting maybe from 6 months to 2 years. Cap that off with customer service people who by voice and tone could not give a rats ** about helping the customer. Today it took me from 3:10 pm to 5:30 pm to get a real person on the phone. When I did the attitude is so reminiscent of a fast food hamburger joint with arches. Yes they know the refrig and ice maker are and have been a problem but they don’t care cause we have no option. Whirlpool will NEVER SEE ANOTHER penny of my money. Time to look at real appliance makers. Horrible.