My old Whirlpool stopped working so I purchased a new one 2 weeks ago. I have had 3 items ruined since using this machine. It is leaving blotchy spots on the clothes and they will not come out. I do not use bleach but the spots look like bleached spots or stains. After reading other reviews I would like to know what the manufacturers are going to do. It is not very economical if we have to rewash everything or replace clothes the new washers are ruining. I have just spent hundreds of dollars for something that does not do its job and would like to know what the solution is. Is there a model washing Machine out there that still cleans clothes? Since mine is only 2 weeks old can I trade it in (Lowes)?

Bought the top of the line Whirlpool Cabrio washer and dryer. Washing machine lasted 3 years. Took forever to do a load and would not be clean after taking an hour to wash. The dryer is still going, but would not surprise me if it died any day. Do not buy.

We purchased a WRF989SDAM03 model French door refrigerator in September. A month later it began to make grinding noises when running. The noises got louder until it sounded like a car idling. We called for service, and the technician diagnosed a failing compressor. They replaced the compressor with some difficulty. Three days later we lost cooling. They replaced the compressor again. Now the refrigerator cools, but it runs 100% of the time. I dont mean frequently, I mean it NEVER. SHUTS. OFF. Its never not running. Today a technician came out, and after 1.5 hrs of diagnostics on the phone with a Whirlpool engineer, theyve declared that it works. Whirlpool refuses to honor their warranty and says that because the unit cools, I should accept that it runs 100% of the time. I can get no resolution from Whirlpool.

If you want clean clothes dont buy this machine(Cabrio Washer)! First of all I find that my clothes have dry spot on them when I pull them out of the machine. Whirlpools response is that the machine spins at such a high rate that the cloth will actually seem dry. Doesnt make sense to me that a shirt that has another garment on top of it gets dry in an unexposed area. I have also been told to always use the high water setting. This helps but the clothes still are not clean. Also my dark slacks come out with residue lines on them - Whirlpools solution; never wash anything in cold water. In addition the machine is very noisy. It sounds like the water pipes are being kicked out of the wall. And forget about washing a king size comforter as advertised, a twin comforter doesnt get clean or even thoroughly wet and residue lines are left behind. Hate this machine! So glad I didnt buy the extended warranty since my attempts to have them stand behind this product have failed. I feel the money would be better used towards a different brand.

I purchased a Whirlpool Washing Machine in November, 2015 and today, I had a repair person out who said the bearing had ruptured and the washing machine cannot be repaired - 2 1/2 years later. Contacted Whirlpool Customer Service who would do nothing other than try to explain to me that I should have purchased an extended warranty as they could not stand behind the machine past the one year. Would not even offer sending a tech out on their dime to confirm what my repairman had said that this is a failed production process of these machines - it was nothing that I had done caused this issue. But yet they wanted to sell me another machine. It will be a cold day before I purchase another Whirlpool product.I was shocked at the lack of customer service to assist with a situation that both the location I purchased it from and my own repair tech said that they are seeing so often with these machines. I would never purchase another item from Whirlpool again nor would I recommend any of their items. I will go to great lengths to give others the background on how Whirlpool will not stand behind their products, lack of customer service to resolve a situation or can work outside of what is given to them to correct a situation - this is not OK!

I have a 1 year old Whirlpool washing machine (Model: WFW94HEXSW Serial:C04151969). The grease from the drum is found to be the cause of clothes being ruined during the wash cycle. I waited over 3 months for a replacement. The drum arrived broken. I ordered again, and it was then said to be on back order. The water shut off developed a slow leak, causing the water to fill, and flow out the front door, causing carpet damage. We have been forced to throw away good clothes, and pay to have our clothes washed, at a not so local laundromat. We feel it would be more than reasonable to have our washer replaced, and professionally installed immediately.

We bought a Whirlpool Washing machine a couple of years ago. We have been having problems. It does not get the clothes clean and laundry has an odor to it. We bought it at HHGreg by the Dayton mall in Centerville, Ohio and also bought the extended warranty. It was the largest capacity machine they had in Whirlpool so I dont need to mention what we spent for this thing. We have had a service tech out 3 times. The first time he replaced a part. It still didnt fix it. So they were out two other times saying nothing was wrong with it. Not only is it not getting the clothes clean, but is putting lint pieces all over the laundry. The warranty place already said if they come out again and they cannot find out what is wrong, then we would have to pay for the service call. We then went to the store we bought the machine and talked to the manager. We got no help from him. All he did was throw us back to the warranty place. Not to mention, the family is having itching problems with their skin because the clothes are not only not getting clean but the soap is not rinsing out. In other words, we are suppose to eat this expense and move on. This is a new machine!!!!! And all it is worth is taking it to a metal place to scrap out!!!!! We will never buy another Whirlpool product again. It is really **. They don’t back their products up and do the consumer right. There are a lot of complaints online about the same identical thing I am writing about. They should reimburse the people the money that they wasted. Thank you.

The Cabrio washing machine I was told by salesman best made so I spent big $$, makes sense right?! Wrong! During spin cycles sounds like jet plane taking off, was told barrings or drive shaft is at fault cause water seeping inside, causing rust, Whirlpool didn’t seal it or designed it to ensure no seepage. Never again Whirlpool. I’m done with your ineptitude, Type: 580. mod. WTW6500WW1. Set.# CY4970595.

AquaLift Self-cleaning does not do the job as advertised. It does very little to clean the oven. Sitting-on-the-floor-in-front-of-the-oven scrubbing is what is needed to clean the oven.

Twelve years ago we bought an LPG Whirlpool range for our new home in Rio Rancho, NM. About 5 years ago, a tenant at our home reported a gas leak and the propane company determined that the Whirlpool range was at fault. The dealer in Albuquerque repaired the leak, by replacing all the valves at a cost of $470. A week ago, after a propane fill, once again, at least one valve was found to be leaking. Apparently, Whirlpool does not know how to make a valve that holds up over time. Over a 7 year period, I paid almost double the cost of the stove, only having to replace it at 12 years. These stoves are DANGEROUS! I will not purchase another Whirlpool product for the rest of my life.

We recently bought a home and our dishwasher came with the home. We saw our basement leaking and got 2 plumbers come over and check the pipes out, paying almost $600, only to realize that the leak was actually from the broken plastic in our dishwasher, and not any pipe. When we called the Customer Service to get it replaced as it comes with a 20 year warranty on the plastic body, they said they would replace the part, but I would have to pay $81 for the first 15 min & $19 every additional 15 min. for labor, which means I would end up paying at least close to $400 or more, depending on how long the technician takes to replace the fiber body. Neither their policy nor warranty make any sense to me. Its frustrating to see that in spite of being covered, I would be the one paying money out of my pocket.

Purchased above refrigerator (WRF736SDAM13) over a year ago and it has been nothing but trouble. Ive had service companies out 6 different times. The doors never lined up or closed properly from day one. The final and last attempt to fix was putting caulk in the seal of the doors!! Left door does not seal properly and moisture builds up on inside. I requested several times for a new one and Whirlpool refused. Also purchased microwave, stove and dishwasher. Microwave went out 6 months after using it. They had to replace a major part. At least they did this at no charge. Just the hassle of having to be home 2 times to meet service tech. WILL NEVER purchase Whirlpool appliances again. Ive been using them for in all my homes in the past. STAY AWAY from this model.

We purchase a Whirlpool washer model # WTW5000DWI, SERIAL #C842 43102 ON 10/30/2019 and it has been nothing but a disappointment. We are senior citizens living on a very limit income with several health problems, and cannot go to a washeteria to wash our clothes. We had a washer that lasted over 19 years and when the motor failed I figured it was more practical to purchase a new washer versus repairing this old one. We had a very reputable Whirlpool dealer here and was very helpful and recommended this washer and the price was in our budget! Was that a big mistake, it does not clean the clothes, does not rinse the clothes with using the 2 rinse cycle and still, does not rinse a load of sheets. I bought a large capacity washer so we could wash 2 sheets at a time. Wrong! You cannot get more than a couple inch of water on the Deepwater cycle, so its like washing clothes on a riverbank on rocks, it rubs clothes together. On my wifes good clothes it will cause little balls of fabrics on them, clothes does not smell clean, and if its real dirty clothes, it will not clean or take the stains out. Its water efficient alright, it does not use any water!Its for sale, and I have talked to a lawyer. Whirlpool customer service was no help at all/All they want was to send a dealer to check it out, the only problem if there is nothing wrong with it that will cost me min. of $125.00. Warranty will cover a manufacturing defect, not a design problem which is what this is. I will just go to small claims courts and get my money back and be done with Whirlpool, hell they dont care! I would buy any washer that is cheaper and has an agitator, without a water efficient features and is top loaded model. It does not pay in this world where large manufacturing companies dont care.

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

Purchased new from Best Buy for over $1000. One or two months after the warranty expired the ice through the door malfunctioned, would only spit out crushed all over the floor then clog up. Didnt bother to repair it, just open the freezer. Next, the door would not seal right and frost builds up in my frost free. Also, the ice delivery wont close tight. Now the unit is about 3 years old and I just finished paying it off and all the door shelves are cracking. Contacted Whirlpool and was told by email politely, Too bad. You are out of warranty, but please buy parts from us and say nice things about Whirlpool because we so value our customers. Never will buy Whirlpool again and recommend you DONT.

I just replaced our Whirlpool Accubake Double Wall oven, model RBD305PDS14, because it fried the control panel after being put on self clean. This was the second time this has happened and I have probably only used the self clean feature three times since we purchased the oven. Im not a specialist in defective product design, but having a control panel burn up two out of three times when the self clean is used suggests a significant problem. I refused to pay to have it replaced again and obviously did not replace it with another Whirlpool product or any other brand associated with the company. I see that this problem has a long history dating back quite a few years with Whirlpool doing little or nothing to resolve the issue. (They just deny any knowledge about any defect in the design.) Fool me once, shame on you! Fool me twice shame on me!

After only 14 months of light use, the magnetron in my over-the-range Whirlpool stainless steel microwave failed. The cost to repair was $350. I paid $450 for the whole unit upon purchase. I wrote to Whirlpool with documentation and got a voicemail that they were sorry, but the 12-month warranty had expired. The independent repair person said it is the Korean manufacturer of the magnetron that is the problem. He is replacing units all over town on all kinds of models Whirlpool is involved with, including KitchenAid. Whirlpool needs to get their money back from Korea! I will never buy another Whirlpool product and have told them so.

Whirlpool Duet Sports washer purchased 11-08 was found defective by service technician due to improperly secured bolts on counterweight at factory. I contacted Whirlpool service and was informed that warranty will not cover any parts or labor. I ordered parts for repair. It will take at least 2 weeks until arrival and repair of item. Clothes washing now were taken to town for washing at additional expense. After repair, only 90 days of warranty was given by the service technician. The cost of $260 to repair item for a possible life cycle of only 90 more days seems ridiculous.

I bought this Whirlpool America dishwasher because it was cheap. Even though Im Canadian, I like patriotism and I could get behind the American flag logo on the washer. Let me just say, if you like when food comes off your plates, and attaches to your cups, then this is the dishwasher for you. It is always a surprise when you open the door to discover which dishes have been cleaned, and which dishes have inherited the food particles from the now clean dishes. This appliance really helps you work on time management as you are required to wash all your dishes before you put them into the dishwasher. 0/10 would not recommend for anyone who wants clean dishes.

Our home is only 8 years old. Our neighbors and double ovens have all gone out! I mean it just quit working and the parts and repairs are crazy expensive! We have already spent $400 on a control board and now we need a control panel which is another $300! Its ridiculous spending $700 on repair of an oven that should have lasted a lot longer! Another thing is that our ovens are white and now the panels only come in black! I will never ever buy Whirlpool appliances again and I am spreading the word to everyone I know!

IM OLD AND DISABLED WOMAN. Bought a brand new $800 Whirlpool top loader washer and it wont work after not even a month. Called whirlpool and had the worst customer service from Tammy. I have to wait to compose myself to call back cause the washer is junk... F9E1 SENSOR. IM NOT A MAN! Worst customer service. Thought my washer would last longer. Its been 1 hour 45 minutes. Wont turn off. I CANT unplug TAMMY! IF I COULD I WOULD!

I am somewhat satisfied with my induction range. We ordered it just before Thanksgiving from Lowe’s a year and a half ago. We were told that we would have it before Christmas, which was fine with me. I don’t cook for Thanksgiving. Just a lot of Christmas baking. It turned out that Whirlpool had not started making our range until January and it wasn’t delivered until mid-January. It had been really good until about a month ago, when it blew the circuit breaker. My husband was cooking dinner while I was at work and it just blew the circuit breaker. No power surge in the rest of the house. No other circuit breakers affected. When the power was turned back on, two burners were out. As it turns out, the main circuit board is dead. So now the one large burner, a small burner and the ovens don’t work. There are two circuit boards for each oven. When it is working, it is a great stove. However when it doesn’t work, it is costly and takes a while to get repaired.

Nice refrigerator. Not enough flexibility in shelving adjustment. Same with compartments on doors, flexibility limited. Freezer design is limited. It is not easy to load the freezer with different items.

Right at 18 months ago, we bought the Whirlpool Cabrio Top Load washer. The last washer we had was the bottom of the barrel Whirlpool model and it lasted 8 years. So, I had no problem purchasing the brand. But now, our washer wont go through the cycles and we hare having lid lock issues. The repair guy said the lid lock was fine which I thought was good news because he said it would be $300 to replace including his service call. Now, it looks like our choice is a $350 motherboard, or a new washer. Whats wrong with this picture? I can go to Lowes right now and buy a used one (exactly the same for $399), pay $350 to repair my two-year-old $750 washer, or buy a different washer? Its hard to believe that a $750 washer is only good for 2 years.

We bought this dishwasher only 18 months ago and its not worth the money we paid. We have had cheaper models that cleaned way better and didnt need as much maintenance as this one. We already had to spend another $410.00 in having the motor replaced in it!! When calling Whirlpool it only has a 1-year warranty and to have a technician come out just to look at it is $150.00. It is so hard to see in the part where you put the jet dry it doesnt tell you when its full or empty and no matter what it always leaves the dishes wet after. Our other dishwasher that was a way cheaper model always cleaned our dishes and never left any food on the dishes unlike this model and we even rinse the dishes beforehand! Look for another dishwasher to save yourself money in the long run!

I saved my money a long time to purchase a new refrigerator (Whirlpool Refrigerator Model ED2VHEXV001). I have very low income so this was not an easy task. April 2009, purchased from Lowes. Ive read similar complaints and also believe there is a defect in the plastic material as there are cracks everywhere on the interior. Shelves have cracked and the whole thing is of poor quality. Seems like Whirlpool should step up and do the right thing. This needs to be replaced.

We just received our brand new Whirlpool washer and dryer from Home Depot. The delivery person started the washer and started the dryer and promptly departed. My husband immediately put a load of laundry into the washer, and he noticed there was insufficient water levels to adequately wet the clothing. Approximately 3 tablespoons of warm water were added at intervals of approximately one minute each. The water level never rose above 3 inches at the bottom of the tub despite setting the washer on the heavily soiled setting. After the spin cycles he removed the extremely damp clothing and it appeared that the machine had not properly completed the spin cycle and drained an insufficient amount of water from the clothing. He tried another load, and it appeared that the sensors were not working which regulate the water levels because most new machines use far less water. However this washer was defective. He then placed the clothes in the brand new Whirlpool dryer. The clothes ran for over five hours and never dried and the dryer never got hot. There was obviously something wrong with the thermostat. We are both disgusted and will never ever buy a Whirlpool product again. In addition because of the extremely poor response from Home Depot, we will never purchase an appliance from them again either. So sad that Made In America, which was on a sticker on the front of the machines, does it mean diddly squat these days.

Whoever came up with the idea of this AquaLift oven cleaning method should be fired! This method does not work. Ive barely used my oven but had some cheese pizza drip on it so thought I should clean before using again. What a JOB! The spill did not come off the bottom entirely and using the non-scratch scrubbing sponge was a joke. There is some soil on the sides and back of the oven that I will have to use elbow grease to get off and Im going to have to crawl into the oven to see if they can be remove. Welcome back to the old days before self-cleaning ovens!

I would not buy any Honeywell electronic water heater thermostat. Has failed two times. I have to pay for a new one to be mailed and for repair. A bad product from all the reviews. Honeywell is claiming they do not service it anymore and gave me a Sears telephone number. Servicemen have said it is a crap product and fails all the time.

I was having trouble with our Whirlpool water heater and thought that wed have to shell out and buy a whole new one. Chris saw my complaint and helped me find the right replacement kit at a minimal cost, as my unit was out of warranty. He even took the extra step and overnighted the parts for us at no extra cost. I was extremely impressed with Chris professionalism and customer support skills.

We bought a Whirlpool Gold Refrigerator from Lowes just over two years ago and have had trouble with it starting a year and a half later. It kept freezing up and the top refrigerator compartment wouldnt get cold. We had to defrost it every three months. Now it doesnt even work. This expensive unit is less than two and a half years old and Whirlpool expects us to pay for the repairs. What happened to the days when a refrigerator would last 30 years? I hate to say it but be smart and buy Japanese. At least they take pride in what they make.

I purchased a Whirlpool refrigerator (model number GX5SHDXVQ02/K02778282) on 9/18/2010. It broke down in 1 year and 8 months; the circuit board control went completely out and ruined all my food. Whirlpool stated I was beyond the 1-year warranty and said there was nothing they would do, except sell me a 1-year warranty for $299. I was at their mercy, so I purchased the warranty for $299 and had the fridge fixed. I would like to be reimbursed at least for the $299 warranty charge. This company should be ashamed of manufacturing such a flimsy product and not standing behind the item to protect their name.

I found this site while looking for a part number for the thermocouple. Lowes had one, but not for the FG model. I decided to call the number on here from Chris to see where I could buy the correct one with left-handed threads. I was told that they would sell me the conversion kit, but I couldnt get just the $8 thermocouple. Then $47.90 later and the conversion kit is on its way. Im not happy about it but at least I got 6 years out of my water heater before the thermocouple failed. The plus side is next time, I can get the $8 part from Lowes and not be without hot water for a week.

Regarding a Whirlpool Refrigerator (model ET8CHMXKQ04) purchased in 05. I dont remember exactly when the problem began but the freezer starts its defrost cycle, water drips down through the refrigerator compartment (soaking all paper/cardboard covered products), collects under the crisper trays and eventually spills out onto the floor. Its a river of water that requires a towel to collect.I believe whats missing is some sort of collection funnel and tube that catches this dripping water and delivers it to the evaporation tray behind the base cover plate under the refrigerator. Obviously, Whirlpool has no quality control nor does it do any field tests to ensure their products are designed and operate properly.

Washer is not worth the cost. After 4th year of use in a two person household the washer bearings are gone and require replacement. The washer sounds like an airplane. I was told based on my description of the issue that the water has leaked due to washing and spinning into the bearing assembly and has caused it to have friction. The Whirlpool warranty is just as costly as the machine.

Our 2.5 year old Whirlpool top loading clothes washer started leaking from the bottom, enough to form a sizable puddle that ran under the dryer all the way to the wall. It was still under warranty so we called the company and they recommended a repair service. Guy came couldnt really identify the exact problem but said hed order parts to stop the leak. That was 6 weeks ago. He cant get the parts despite us calling about every week to see if the parts came in. So for the last month weve been taking our clothes to a laundromat. There seems to be no end in sight to this problem. Seems stuck between Whirlpool and the repair service and were the victims. And, oh yeah we got a note that says our warranty is ending soon.

Front load washer Whirlpool Model# WFW9400SW02, only had this machine for about five years and the main interface control board has gone bad. This part cost 1/2 as much as buying a new machine. My parents had the same washing machine for almost 30 years and no problems. Whats wrong with this picture?

I have had 6 months of absolute HELL working with Whirlpool. I mistakenly purchased a Whirlpool Refrigerator from Home Depot and the moment I did Home Depot were hands off. Sadly my brand new refrigerator didnt work from the moment it arrived. The ice machine was dripping inside from the back making all the ice freeze together and created an ice sheet below the ice box that can be taken out. There also was water dripping out of the ice output. The water output wasnt working and the water was literally trickling out when you pushed for water.SO Whirlpool took 6 weeks to send their 1st technician from L.A.R Services out of Boston and the guy turned up and said it was due to needing a new ice tray/machine and our sink having an old filter. There was NO filter on the sink! And he then ordered an ice machine that arrived at their office in 4 weeks but they took 3 weeks to try to deliver it. When they finally came out they called to say they had to turn around because the road was blocked- there are 3 ways to get to our home....so I had to chase for 2 more weeks to get them to come back out. When they arrived they handed me the ice tray outside and drove off!!!SO WE TRIED AGAIN and this time had Home Depot call Whirlpool to get a service person in to fix it. We had to wait another 5 weeks and when he finally came he claimed our issue was due to the fridge not being perfectly level. Well, guess what, its now level and the ice is still freezing into giant blocks, some weird plastic strap is hanging inside the ice box and the water is still trickling out.Ive called the service guy 3 times and he is yet to call back and right now Im on hold with Whirlpool (its been 14 mins so far). NEVER AGAIN will I buy anything WHIRLPOOL and I will be sharing this experience in every consumer space possible so no one has to go through what we have. Our new fridge is still broken after 6 months!! All I want is my GE fridge again and I should have a followed the reviews.

Washer doesnt get soap out of clothes. Had tutorial from service man. Must use extra rinse every time and still have soap on dark clothes. Worst washer I have ever owned. Makes washing a lot of extra work and frustration. Have tried everything to no avail. Takes at least three times longer to wash clothes with all the steps I have to take to get soap out. I understand EPA demands for less water usage, but clothes still must be properly cleaned.

I’ve had my Whirlpool Duet for 12 years and it has been a great one. I’m a mom of three sons, all of them wash their own laundry!! Lots of loads are done weekly and it cleans well! We leave the door opened after it’s unloaded so the tub will dry. Every few months, I put a tab in it so it will clean out all of the buildup. I don’t get the “front loader smell” that way.

Purchased both Cabrio washer (wtw6200sw2) & dyer brand new in 2007 for $1200. Within 4 years the motherboard went out. Whirlpool didnt want to fix it. They said it was past warranty. After many complaints to corporate, they sent someone out to repair it for $496 (they paid). Repairman said these models had motherboards from Japan & Whirlpool was aware of the many issues, but wouldnt do a recall. 2009, the springs went out, 2011 F codes began to appear. Clothes dont get clean; not enough water. 2014 & 2015 DU & DL codes appear. Now I need a new Lid latch assembly. These washing machines are not worth buying. Never again will I buy another Whirlpool!! My mom had an old Kenmore that lasted 20 years and only needed a replacement belt. No more fancy high end washers for me!

We purchased a Whirlpool washing machine for $600 from a local retailer and it broke down within three months. It is now been two months and two repairman visits later and still not fixed. I called them and talked to customer service who then transferred me to another department. So far it’s just been the typical runaround with no results. I demanded an immediate replacement but was told that would need approval from yet another department. I don’t remember what departments are involved nor do I care. I am simply disgusted with this baloney.

Whirlpool dishwasher Wdt790slym1 - This is the worst dishwasher I have ever bought. The top rack assembly is made of all plastic and started falling apart within 13 months of purchase. I have had to order the same replacement parts numerous times and have reached the end of my patience. Buyer beware!!

Whirlpool Washing Cabrio machine model WTW5500XW0 - I purchased this machine five years ago. After about a year I started having problems where the clothes were not coming out clean. I contacted Whirlpool and was referred for a repair. The repair man told me these newer machines need the Affresh product to clean out the machine so this doesnt happen. I bought the Affresh product and there is still a problem. Every load of wash has to be put back in for another rinse cycle, sometimes two rinse cycles. Its ironic because the cover of the booklet for the machine says low-water washer which was the selling point to buying this machine. Instead of using less water, Im using DOUBLE the water.

Bought this dishwasher (Model No WDF530PAYB3) in 2013. First the plastic latch for the dishwasher detergent door broke. Then, the paint on the face of the door started to bubble, peel, and now is rusting. Next, the heating element broke. Lastly, it started leaked on my wood floor causing damage. 2013-2014 I bought that Dishwasher, Micro-Hood, Stove, Refrigerator, Washer, and Dryer all Whirlpool. All the kitchen appliances were Whirlpool Gold. They would not fix their product. Offered a discount on a new one as if I will ever buy Whirlpool again.

Bought wtw4800 washer brand new came with 1 yr. warranty. 19 months after buying plastic bearings went. 2 different technicians told me could not be repaired, junk. Washing machine less than 2 years old and can’t be repaired. Called Whirlpool. Told me they could do nothing to help me.

Whirlpool Washing machine Model WTW4800XQ1 - This machine ran fine for the first 6 months, even though my old machine took 40 minutes for a large load and this one takes an hour. Then, I had to call the repairman out and he said it was the fill valve. He didnt have one on the truck and said he should get it in within 3-5 days. Well a month later, I had to call Lowes again to find out what the problem was. They had him back out with the part within 2 days. Then, I had to call again. This time the repairman ran a test and found a bad spin motor, he had the part on truck. Third time to call and the machine is back to not spinning out properly. My old machine lasted over 14 years. Whats wrong with these new ones?

Both are Whirlpool Commercial quality. I got them free from my Co-Op. They didnt cost me anything. They have been here for years - at least 18 years. They have performed flawlessly. I would look for anything discounted. I do not have a problem buying scratch and dent items or last years models. I am not big into brand names and their claims. My sister has gone thru several Maytag appliances in just a few short years. I will not buy any front loading washer, its top load only for me. The dryer has to be electric because we do not have gas in my Co-Op complex. I have been lucky to have only two washer and dryer combos since I was a kid. My family bought a Kenmore washer dryer combo in the 70s that lasted maintenance free into the 90s when I got the Whirlpool set that I have now. I only need the basics side by side set ups. Even though I live alone I do a lot of laundry. Since I have had these commercial grade machines I am more leaning toward another set of commercial grade machines. They seem to be able to take more abuse/over loading than the fancy expensive machines.

I love my washer and dryer but am a little disappointed in a few areas. First, my washer stopped spinning normally after a few years, I forget exactly why. Then my clothes were too wet when it was done. My dryer then did not get my clothes dry in one cycle. Also, it was going to cost $500 to fix my washer which wasnt worth it. But Whirlpool did send us a new tub and all the parts for free. Thankfully my husband is handy and after finding a YouTube video, replaced it all and now it works again. My dryer still doesnt always dry everything all the way. I often have to do 2-3 cycles in the dryer to get my clothes dry. I thought there was supposed to be a sensor that would keep the dryer going until there was no more moisture. Maybe that is broken too.

I purchased a Whirlpool French door refrigerator model # gx5fhdxvyo4 in June 2011. Four months ago, ice was forming on the bottom of the freezer. Repair person replaced a clogged plug leading to evaporation tray. Its March 2013 and repair person now has to replace evaporator motor part # W10128551. I contacted Whirlpool and was told the warranty has expired (one year). This repair will be around $175. How can I trust a Whirlpool product in the future?

We have Whirlpool dishwasher for almost 10 year, very happy with the performance. This dishwasher is very quiet and also very spacious. The look and the price compared to other model is compatible and I will recommend it to other household. Thanks.

Originally, I loved my machine. At the one year mark, my washing machine began a f51 error code. I looked it up and it had a recall. The entire board had to be replaced. Now, I keep getting a ul code and it will not quit. Also, the inside of the top is rusting out so badly that chunks of rust fall into the washing machine and stain my clothes. I wish Whirlpool would fix these common errors. I see many other people complaining online that the same thing is happening over and over.

My glass stove top broke for the second time. The first time Whirlpool accused me of dropping something on it and chipping it. I didnt but paid the $400 glass replacement. Today while cooking, I put cold from the fridge not freezer, sausage into a warming fry pan. I heard the same pop I heard 2 years previously...sure enough the glass stove top broke. After a phone call to whirlpool, and hearing they were sorry but theres nothing they can do, I will write as many letters I can so others dont buy whirlpool.

Its a front loader and has lots of cycles and temperature to choose from. Its setting on a pedestal so its not too low. I dont like the way the soap is dispensed.. If you still have the door open when you pour it in the dispenser it almost comes out on you. It also knots your clothes up and makes them hard to get out. The rest is good.

I purchased a Whirlpool catnip washer from Brandsmart in August of 2010. It worked fairly well, but would sometimes need for clothes to be rearranged in order for the spin cycle to complete. In June of 2013, it started to not wring the clothes out completely. It then stopped working. I called a repairman and got an estimate of $550 dollars, but I paid $578 for it.I called Whirlpool and spoke to the supervisor of the consumer concern team. She offered me a fifty percent discount on the parts for the repair. I checked the web to see if anyone else had any problems with this product and found several. I suggest you do your homework before purchasing a Whirlpool washer. I was positive they would do more, since it’s such a prestigious company.

I replaced our old 50-gal water heater (10 years old) with a new top-of-the-line Whirlpool 50-gal water heater in Feb 2011. The Friday before Memorial Day, the heater went out and the pilot refused to stay lit. I called and jumped through all their hoops and finally figured out that it was the gas valve, because the pilot goes out as soon as you release the button and the milli-voltage reading is ok. They sent me a replacement and it cost $145 to have a plumber come out and install it. We were without hot water for 5 days. Now 9 days later, the pilot keeps going out. This time I can re-light it, but after the water heats up, it is apparently going out again. They refuse to replace a 12-year warrantied water heater that is only 2 years old and I am going to have to hire a plumber again to come out and attest to what we already know. This water heater is extremely loud. When we had it installed, I read the reviews and there were similar complaints (sounds like a mini jet engine). We dont seem to get as much hot water as we did with our old builders grade heater. This is a bad buy and I would advise anyone looking to purchase to look elsewhere.

Im very happy with my Whirlpool washer and dryer. The washer leaves the clothes clean and has a variety of wash cycles and water levels and is quiet. The dryer also has a variety of drying selections for all clothes and heavy loads and its very quiet.

We purchased the washer on April 25, 2015. It has been an absolute nightmare. Reached out to Sears within a week of delivery because the wash cycle was way over an hour. Is a terrible machine, my clothes come out dirty, is damaging my clothes and Sears says I cannot return it because according to them I havent had it fixed enough times. It washes for over an hour at times. It takes water and releases water and goes to wash again but is not cleaning the clothes. As a homeowner we pay water, and electricity and perhaps I wouldnt be so upset if my clothes would come out clean. At first the tech told me to change from the HE detergent purchased and recommended at Sears to liquid detergent and then since I still get stains on our clothes he advised me to use less than the recommended amount. I also purchased the kit to wash the machine. This is a real lemon and nobody wants to admit it. I have purchased Whirpool washer before but if they dont admit that this is poorly made and give me a voucher to buy another machine I will never ever in my life buy Whirlpool or Sears for that matter. The machine is just a year old and I cannot use it because it damages my clothes and worst, is not cleaning my clothes. It disgust me to wear dirty clothes or to have my family wear them. So now I have another appointment and at this point I no longer use the machine. I will tell everyone that is willing to hear my experience. Do not purchase this washer, is not good and is only trouble. You are not going to be able to get it exchanged or fixed. I think that a full year would have been enough time for Sears to determine this is a lemon and do the right thing by the customer. I now go to the laundromat because I have a machine that damages my clothes. I am also out of money to purchase a new one and the wearing dirty clothes disgust me.

Water pools at bottom of freezer and onto floor. Has been repaired twice, but still leaks.

I had my entire kitchen re-modeled in May of 2013 and purchase all new Whirlpool appliances. I work for Standard Pacific Homes and purchase the identical appliances we provide in our homes. I am so disappointed in the refrigerator. Two months ago it stopped making ice and I was told to replace the filter and it would be OK. I did that and still no ice. I bought ice trays. A couple of days ago, I came home to find water on my kitchen floor coming from under the refrigerator. I called Whirlpool again and no real help.... Told me to call Lowes. I called Lowes and they gave me 3 more numbers to call for service. None of those service providers had any available appointments and told me to call Whirlpool. Meanwhile my refrigerator is standing in the middle of my kitchen so I can keep the water mopped up. The refrigerator was so difficult to move. Getting the feet moved up so the wheels could touch the floor took an hour and I ended up with bruised hands. My lesson in this is to buy a better brand next time and go top of the line. I sell these to our buyers at Standard Pacific Homes everyday..... Wish I could believe in the product.

Whirlpool Cabrio wtw6400 - Never, never, never will I purchase a Whirlpool product again! I spent nearly $1,500 on this washer and dryer. The washer ties everything into knots and has had several problems, most recently the bearings going out! I just called customer service who said they would send a repair man, approx. cost $370. What a rip off! I strongly encourage everyone in this same boat to call their customer service complaint line and/or consumer reports. I bought from HH Gregg and will never shop there again either.

All of these awful reviews and you continue to sell the Made in China JUNK!!! And shame on the stores that advertise and sell Whirlpool JUNK!! They should put a warning on these machines stating Will not last, gets off balance and does not clean your clothes. Yes we bought the Cabrio like the others, our clothes would not get clean, because like sheets, would end up looking like a doughnut without a hole and all of the dirty water would drain through the middle and make a spot. Then you have to wash them over and over. But that is not the worse part! It only lasted 13 months, YES I said 13 months just past the warranty LOL!!When the man came to make repairs, it was the gear box and was going to cost almost $600. Almost as much as we paid for the machine. He recommended getting a Speed Queen, we did and I LOVE it!! I think it is the BEST MACHINE I have ever had. They are a little hard to find though, but I found where they were sold on the internet and the dealer had to order it. Well worth the time and trouble, (trouble) which I dont expect to have with this machine. Like I said it is a wonderful beast. And I will never buy another product made by Whirlpool. Before my husband retired he made prototypes for autos so he knows about testing and Whirlpool had to know this product had bad flaws before they put it on the market, I call that fraud. Bad taste in my wallet, Michigan.

We bought a Whirlpool washing machine two years ago and bought the extended warranty. The machine quit working so we called the warranty service number. We have had a repair man sent here 5 times from them. The technicians have put two new control boards and a new door lock on it. They have another part ordered for this week.The machine is still not working after five visits from service technicians and they say they cant fix it. The extended warranty service plan says if it cant be fixed they will replace it or send us a check for it. We have contacted them several times and they dont want to make good on it. So we have a broke down washing machine and have to go to a Laundromat every week.

I purchased the extended warranty for my refrigerator and the warranty company sent a technician out to repair my refrigerator. It has been six weeks and 4 attempts and no one can do anything to fix it. The warranty wont refund my money without deductions from the company coming out and fixing nothing and says itll take 2 weeks before I can get that. After mailing in writing that I want to cancel 500 dollars wasted and no one wants to help. Thanks Whirlpool. Ill definitely let all my family and friends know of my experience.

My Whirlpool microwave broke. Im not sure how or why so today I purchased another 2 actually. Both were too big. The model I purchased is discontinued. I had to remove part of my Marble Backsplash - the turntable is tiny however mic is huge. Work on making microwave for smaller areas. Stick to get or Samsung for a nice size microwave not a Mongo mega oven above your oven.

I bought a water heater in 2008 from Lowes department store. The heater would continually go out causing no hot water. The company had sent several technical repair men out to resolve this problem, and still the problem remains. The Technical Support requested that they will pay for the part and I could install it, not knowing if I am able to do such a job. The technicians who were sent to my home were not able to do the job. How do they expect me to do the job without proper experience? Whirlpool products are not reliable nor is their maintenance contract. Stay away from this company.

Our Whirlpool refrigerator has been an extraordinary kitchen appliance, it may even be 28 years old. The ice maker worked until just four years ago and thats amazing. Its never been serviced and never needed a repair. I dont know what one can say about something thats worked so flawlessly. This seems a little bit trivial when considering the cost of a new appliance, but the plastic veneer on the handle had fallen off and needed glued back on, but thats about it as far as maintenance and repairs go. Overall its been an ideal purchase and I wish wholeheartedly all my purchases were as good as our whirlpool refrigerator.

Whirlpool Cabrio - What a nightmare. One year in… from the beginning the washer completes a cycle without attention. It gets stuck in a rinse cycle and eventually stops with an FF error display. Because of this it wastes HUGE quantities of water and takes far too long to actually wash clothes. It is so frustrating. We will buy a new Bosch and THROW this way. We cant even pass it on to our grandchildren.

My girlfriend lives in Europe and bought a Whirlpool stove and countertop burner. She was washing dishes and heard a sound like a crack and she looked around the kitchen to find out where it came from. She looked at her stove top and there was a vertical crack down the center of it. It was turned on, no one was using it but it cracked. She tried to get a replacement glass top and the store told her they were not available. I sent an email to Whirlpool to find another one and never heard back from them. I sent a second email and that was left unanswered. After this I would never buy another stove or stove top made by Whirlpool again. Knowing that KitchenAid was bought out by Whirlpool these comments dont surprise me one bit. Whirlpool is another name for poor quality and no service.

l will never buy Whirlpool appliances again, nor do I recommend to anyone. My wall over was 1 1/2 yrs old with a worthless 1 yr limited Warranty. I had Total Appliance from Cleveland do the repair, the only ones I found at the time that would work on this type over with a Digital panel. I think the engineers think we all live in Silicon Valley. Unfortunately the cost to repair after I cleaned the oven for the first time was $384.00 to unlock the door and 2 trips and he had to remove the door to replace 2 fuses so the door and panel would work! Im afraid to clean them oven again..I called Whirlpool and the first wait time was 70 Mins... I put the phone on speaker, finally I talked to 2 Customer Service men to no avail. He basically said my Warranty was up and nothing they could do! I said I was going to complain on Social Media and he didnt care! Go to Consumers Digest before you buy any new appliance! PS, I also went on YOUTUBE and you can see all the TROUBLESHOOTING ON MANY APPLIANCES!

Washing Machine Model WTW4616FW - I purchased this machine at Home Depot after I had to return my Samsung Costco machine that was recalled due to the glass top flying off. I was attracted to it by its simplicity in design and price. I have had it almost a full year and love it. I like that it has the deep water wash for over-sized items and a full-sized agitator. I was shocked that it was actually Made in America. I highly recommend it and I hope they keep making this reliable machine that gets the clothes clean. Awesome machine without the bells and whistles that I dont expect to breakdown. Way to go Whirlpool!

Whirlpool gas range Model WFG5245LAB2 has serious flaws that are a danger. I noticed the handles to turn on the burners seem sloppy. So sloppy in fact that just brushing up against the knobs will turn the gas on. This happened when I had someone visiting and we returned you could smell gas in the house. We were none the worse since we were out however my 3 cats were in the house the entire time. Tonight I removed the large grates that go over the burners to clean the porcelain. Once again I brushed up against the handle and the back burner ignited causing me to burn my hand. This stove is a danger to all.

Let me just start by saying I have multiple Whirlpool appliances, and I have always bought Whirlpool appliances in the past. I bought a refrigerator 3 months ago, and it quit working. So, I called Whirlpool to come service it. The service repairman said someone left the freezer door open and it froze up. Two days later, I had to call them back again, because now, the fridge part was not keeping food cold. He came back out and told me it was the compressor. I then in return called Whirlpool that afternoon, and they refused to replace it saying they had to follow their Warranty Policy and they would call me back on Wednesday. They did call back on Wednesday and told me they had located the part. I got a call on Tuesday of the following week and was informed they could not locate the part. I called Whirlpool the next day, and they told me they would have to send it to their Exchange department for review and I would hear back from them in 3 business days. I asked for them to rush my request, but they told they have no way of doing that. I will never buy a Whirlpool product again!

I purchase a suite of Whirlpool Kitchen Appliances April 2017. My range is the slide in model. The knobs are on the front of the stove top. I 4 months in I saw that the paint behind the plastic panel where the knobs are was chipping. Also, the gasket in the oven had some loose threads so I finally decided to call the warranty. Whirlpool paid for the gasket to be replaced but Customer service said the chipping was cosmetic and that only covered for 30 days. I am so disappointed in this range and Whirlpool. My stove looks very used after 10 months. I followed the instructions on what to clean it with and how to clean so I know its not me. The paint chipping is crazy! How as consumers do we deal with this? This Range was a cost over $2000! and they give me touch-up paint!I purchased Whirlpool because I researched prior to purchasing my appliances. I thought I was buying Quality, this is not quality! At Christmas I had a pot of potatoes boil over and the element circle on the glass top cam off with cleaning. This too is not covered because its cosmetic. Ironically, my old glass top Whirlpool range did the same thing. That why I got a new one! I guess it still works. Who cares how it looks... RIGHT? Well, I WAS a good Whirlpool customer. Not anymore! Do not purchase Whirlpool glass top ranges unless you want it to look worn out after less than one year. I have tried to post pictures but this wont let me paste them!

I purchased a Whirlpool washing machine from PC Richards in Lake Grove 15 months ago. I paid $590.00. I had to call PC Richards back because it sounded like the machine was not spinning right. The servicemen came back and said nothing was wrong. It was supposed to sound like that. Now the machine stopped draining and spinning. I went to the store and they handed me customer service numbers and said they could not help me. I contacted Whirlpool online and received a phone call from a woman that gave me a lesson on how to load the machine and put soap in it! She was a very polite woman, but, gee, that didn’t solve my problem.After 4 days I was able to get through by phone and was told to call service. I contacted Mahler Appliance. He looked at it and said he couldn’t fix it and took a check for $81.47. He told me to call Whirlpool. I called Whirlpool again and got their service people. The gentleman came and could not figure out what was wrong. He tried a few things and said it was probably the main board. He said to call Whirlpool, but they most likely won’t give me back my money. He could charge me $460.00 for a new board per his supervisor. I just paid $590.00 for the machine and another $87.00 to some guy who took advantage. He left with an $87.00 check and I still have a broken washer. He did tighten up a loose wire he said he found and told me to try it and good luck. So I tried it. I put clothes in and turned it on.I came back about 20 minutes later to see if it continued to run and I slipped and fell on the ceramic floor because water drained out from somewhere and went all over my floor. I have injured my back and elbow from hitting the hard floor. I also have water all over the place and finally a very broken defective washer. I am angry. I hurt myself and have spent close to $1000.00 and I still have no working washer and no way to buy another one. The washer is 15 months old. That’s brand new to me. There was obviously a problem from the beginning. Whirlpool has always had a quality name for years. I would hope that they would stand by their product and fix my washer for me. It is obviously defective.

I have not had any problems with my Whirlpool refrigerator. It is four years old and has had two owners, including myself. It has the stainless steel look and has top to bottom french doors, one side is the freezer and the other the refrigerator. Both sides are equally the same size. It has a filtered water dispenser and ice maker in the door. Id say for the price it is a really good value.

I bought this stove 4 years ago from Lowes. I have had nothing but problems ever since. My family is now afraid to use the stove and Whirlpool refuses to stand behind their product. The last straw was a bill for a service call that took 6 months to complete without correcting the problem. Whirlpool sent me a bill for $100 to pay for the privileged. When I complained, WP said if I paid the invoice, they would give me a deal towards a new stove. Meanwhile, the old stove does not work and we are afraid to use it, given our experience with its reliability and safety. I plan to return it to Lowes and buy anything but a Whirlpool product. Beware of Whirlpool Maytag anything!! The customer service is shameful!!

As many others have posted - the Cabrio washer is awful. Cycle time > 1 hr. Clothes not clean and caked in soap even with extra rinse. Phone Whirlpool and found they dont care. All theyd say is its government regulation fault but for $100 they could send a technician to ensure it is working as designed. To environmental reasons for the new design, seems to me it missed the mark. Longer cycles, extra washes, extra rinses... All I can say is - Unbelievable!!!

Buyer beware! I purchased a Whirlpool Cabrico topload and with my second wash, I realized I had a mess of a new washer. Ive called the call center on 3 separate occasions and I have spoken to other customers who have the sample complaint. The clothes are not washed clean. They have a residue left on them. My advice to all potential buyers, dont even consider buying a Whirlpool Cabrio washer. It is the worst purchase I ever made in an appliance. Im very unhappy with my washer.

We bought a Gold Series dishwasher on 2/12/2013. It stopped working properly and we had a service call on August 6, 2013. Since then, we have had 3 companies come out 5 different times to try to fix the machine. Nothing on the top rack gets clean. In fact ,they come out dirtier than when they go in. The last service call was on October 7, 2013. I was told by a Whirlpool representative that the repairman would call technical services and that if the problem was not solved, that the machine would be deemed unrepairable and that Whirlpool would replace the machine since it was within the warranty. I was also told that their standard is that if a machine has to have 3 service repairs to be deemed unrepairable. So 7 days after the last repair, the machine was still not washing correctly. Once again everything on the top rack was dirty. The machine has had the motor, the pump, and the hoses replaced. Still doesnt work. So I called again to get the ball rolling on replacing the machine and was told that they would not replace the machine and that I needed to have another repairman come out and sit in front of the machine and call technical service. Apparently, the previous repairman didnt follow their instructions. I called and complained twice, I guess Whirlpool thinks that as consumers we have the ability to change work schedules, school schedules, take vacation time, etc. to wait around for the 6th service call, and wait through the 5-hour window that we are given for the repairman to get there. Well we dont. Obviously I have given Whirlpool plenty of opportunities to fix this problem. They havent been able to do so with 3 different companies. There comes a time when you just stop kicking the dead horse. Now is that time. If they cant figure out whats wrong the first time, and not the second time, and not the third time, why do they think the 6th time is the charm? Because I got so upset with them, they referred me to a customer care manager. She called and left me a message, and I have been calling her now for 2 days with no success on her DIRECT line nonetheless. My phone calls are not returned. I wont even go into how many customer service reps told me a different story every time I called. Whirlpools customer service doesnt care about their consumers. They dont care about our complaints. Now I have a $600 piece of junk. I will never buy another Whirlpool product. I will make sure that every person I know that is looking at appliances knows about what a horrible company Whirlpool is. They just put crap in a shiny package!

Purchased this oven on 9/12 from Sears, did not purchase an extended warranty and didnt think it was necessary. Im a 64 year old widow and only use the oven on holidays, to date Ive used the over 5 times. With Easter coming, I decided to clean the oven. Followed the instructions, the door locked and the oven died. Im totally disappointed, now it would cost over 100.00 to repair, money I cannot afford. Called Sears and all I was told over and over again that they can send a repaid person and I would have to pay. I was also told that I should have purchased a Kenmore and I wouldnt have had a problem and finally I was told that they couldnt fix it and referred me to whirlpool customer service, who also told me it would cost over 100.00. A 19 month oven should not have died. It should have cleaned the oven and continue to work for many more years. Again, Im upset, angry and disappointed with sears & whirlpool. And dont know what to do. Does anyone else have this problem with the oven, is there a recall?

You have to take into account that this microwave doesn’t heat up as others I’ve had so even if the instructions call for something to be cooked for 5 minutes, you have to add at least 2 minutes more. If not it would be undercooked.

First, I was put on hold by the first female for 44 minutes, and then a second woman finally answered, and said she didnt know why she would send me to her, because she was in the sales department, and she put me on hold for another 25 minutes. I finally had to go, because I had an appointment. When I got home, I called back, and got a man by the name of John, and at least he recommended he could schedule a repairman. The problem I told him is, the inside wall of my refrigerator has 2 cracks on the side, and a crack on the back wall. I dont want a repairman to come, just to tell me he cant put 2 new walls inside of my refrigerator. I could not find an email, so I could email Whirlpool about this problem, and definitely, they were of no help. I bought the refrigerator at Lowes late 2003. I have never, in my life, seen the inside walls of a fridge do this. I spent a lot of money for this, for it to crack on the inside walls. It does not seem like something is right with this.

In 2008, I purchased the 40-gal. Whirlpool electric water heater to replace the original unit in my home that had lasted 14 years without issue until it died of old age. After about 2 1/5 years, it died and I was given authorization to return it to Lowes at my insistence. Now after another 2 1/5 years, this one has died. So far, I have replaced both elements, lost a days work, missed out on a date because I could not take a shower and now Im told I have to replace the electrical box on top which wont get here until Monday. Its Saturday and I havent been able to take a shower in my home for 5 days now.The first CSR (Crystal) I spoke with implied that since I had 2 consecutive failures, this was a site problem, not a product problem. Theres nothing special about my site, and my old unit made it 14 years with zero repairs. I would argue that since both of the units only lasted 2 1/5 years, that the product is substandard. I asked to speak to a manager but was told no because they were all busy (no doubt) and her demeanor was unapologetic and unsympathetic. The second CSR (Nick) I spoke with was very nice and at least sympathetic. That goes a long way in customer service, but I was still not allowed to speak with a manager.I am going to try and repair it one more time, but I have zero confidence in Whirlpool and would never buy another Whirlpool product of any sort again. If I get it working, and after all Ive read here I doubt that I will, I will only be using it for the time it takes to get a replacement of another brand. This was my first experience with a Whirlpool product and you can be sure it will absolutely be my last.

I purchased a Whirlpool duet, model #wfw9550ww00, two years ago with added warranty. The machine stops mid-cycle. The time remaining flashes but no error code. Pressing start would begin the machine again. Sometimes, we could go several loads with no problems and other times it will stop three or four times in one load. Occasionally, pressing start would not work and the machine would require unplugging and restarting. We have had several service calls in. They have said it was the pump, then it was the motor, then it was the pressure switch, and yet the problem persists. They are due to come out again tomorrow for yet another examination to determine its cause. Its the third time in one month. Its a lemon.

I redid my kitchen two years ago. Put in Whirlpool appliances because they matched my refrigerator. I have been very happy with all aspects. It looks good, it’s easy to clean and cooks well. It doesn’t have a lot of special settings. Less to go wrong.

We purchased the model WFC7500VW, 24” washer and accompanying dryer in June of 2015. Within a couple of months, the water pump went; also we continually had to take the front panel off and clean out the filter when we get an A11 code! Now we experienced an F06 code... This code means the washer can’t go into high speed. The repairman (Whirlpool recommended), told us that a new tachometer motor, etc would run $500-$800 with labor! He also said that the noise the drum made was bad. My dryer works fine (only complaint is the grinding noise it makes, which Whirlpool told me is normal)... I would like to purchase a new washer, but don’t know what will fit under the dryer. I do not want ANY Whirlpool product!

I purchased a 40 gallon water heater at Lowes and installed about 3 years ago. A couple of weeks ago, it got an upper sensor failure code on the gas valve. It would heat by resetting (turning valve off, waiting a minute and then lighting) but after a few minutes, it would fail again. I called the customer service and they mailed out a new upper sensor. When it came a few days later (I paid for shipping), I installed it but the same failure code. Again, the only heat I could get was by resetting the valve several times before a shower. I called customer service again, told them what I did and they said, Oh, the problem is the gas valve then. So they mailed out a new gas valve unit. It then came a few days later and I installed it according to the enclosed directions to the letter. Still got the failure code and still had to keep resetting it to get any warm water before a shower.I called customer service again, told them what I did and he said, Well, did you flush the water heater with apple cider vinegar before you installed the new gas valve? I said, No, it wasnt in the enclosed directions to do so. He said, You should have done that and it would have worked. I will send out a new gas valve. At this point, I blew up. Two weeks with no reliable hot water. I told him I want a new water heater and he refused. I asked to speak to his superior. He said no. Dont ever get a Whirlpool product. Some other crappy company builds these turds.

The Whirlpool hot water heater model ES80H123-45D from Lowe’s is a free replacement for a lifetime warranty unit that went bad after 8 years. First heater would heat to 154 degrees with a setting of 150. Very good. New one heats to 140 degrees with a setting 150 degrees. Digital ESM screen on heater reads 150, but the water is only 140 by my temperature test. I talked to complaint line 5 times in 7 days and was told to do various test, but the temp never went past 140. They replaced both thermostats and temperature still never past 140 with ESM reading 150. They first told me standard temperature was plus or minus 5 degree range. Then, they changed their minds and said it was 10 degrees. They are calibrating their equipment to operate 10 degrees less then their Energy Smart module reads to cover up a performance issue with their water heater. They say this unit will operate between 80 and 150 degrees—nothing’s said about a plus or minus operating range. I will buy a new temperature gauge to see if my old one is correct. It was tested against a digital one a couple of years ago when I had a new dishwasher installed by Lowes. The installers gauge read over 152 and mine read 154 degrees at the sink next to the new dishwasher, so it was close to accurate at that time. Whirlpool is happy with their under-performance.

I am a very unhappy owner of a Whirlpool Cabrio Model: wtw5640xw0 & matching Dryer. About 4 years ago, my husband chose to replace our 11 year-old Maytag Performa Washer & Dryer instead of fixing a part that needed to be replaced in the Washer. I was upset with the very first load of laundry in the Cabrio and I was extra upset that my husband had junked my perfectly awesome working Performa Dryer. )-: First of all, the Cabrio set is Extremely LOUD! Secondly, I often have to wash loads more than once because they do not get clean the first time. Next, the Washer is Always knocked off balance. Ive resorted to using the settings on the Washer with the low spin every time, no matter how light the load. And, now there is something wrong with the lid lock mechanism (which has always sucked anyway), but this is a new problem... I was just checking on the internet to try to figure it out when I stopped to write this review. The lid will not lock & the lid lock light wont go off, so the Washer wont do anything at all! I can not express enough what a piece of junk this Washer is & Im never going to allow my husband (who doesnt even do the laundry) to choose my Washer & Dryer again!

I like the looks with brushed stainless steel and black. The most difficulty was getting someone to help get it and load it. But other than that, Ive had no problems with the dishwasher.

I have always liked Whirlpool products but it seems lately they are lagging in this department. My washer/dryer combo each separate I dont feel are doing the job they should be. Washer is the bigger problem. Softner dispenser not distributing the softner correctly and now I have to clean out after each use. These are about 10 years old now. Is not spinning all the water out and not at all sure if clothes are getting clean. Most of their products usually lasted much longer back a few years.

The exhaust fan for the gas range runs when using the microwave. The noise is loud and very aggravating and there is no way to turn it off. From what I can find the older models there was an option to turn it off. On the new models Whirlpool cut costs by not putting a small (QUIET) fan in the microwave but used the range fan for a dual purpose.

Safety issue with Dishwasher Model MDB6949SDH. Fire hazard! Strong electrical burning smell when using powerblast function. Waiting for some Whirlpool action but does not look to be too soon. Chat noted a report to be filed with safety department and will hear from them. No hear so far. Pick up phone Whirlpool.

All JUNK!! Replaced all new within the last two years. The washer I replaced was twenty + years and was still working fine was just upgrading, big mistake! Washer is sounding like it is going to walk out the door. Replaced dishwasher after twenty years and the new one was leaking within one year and recently got replaced. The new one did not last one year and also is leaking. Now washing dishes by hand. Lastly replaced hot water heater and that is junk too. Has six year warranty after one year pilot light wont stay lit, Whirlpool said would replace the gas control valve for free but I need to pay to install. I WILL NOT PURCHASE ANYMORE PRODUCTS FROM LOWES OR WHIRLPOOL AGAIN!!! HOW CAN A RETAIL COMPANY REPRESENT SO MUCH JUNK?

My Whirlpool washer would start up but would not add any water. It sat there doing absolutely nothing. Then it showed a code on the screen. It said to disconnect the power for 1 minute and plug it back in, which I did. I repeated that process several times. Still nothing. It also said to call Whirlpool, which I did. They wanted the Model # WFW97HEXLO and Serial #, I gave it to the gal on the phone at Whirlpool. I was told it would be a week before they could get someone out there to take a look at it. Really!! I work 80 hours a week and live in the country. I dont have a week. When I asked where the service man was coming from, he was coming from another town. I asked if there was someone closer. She gave me another appliance stores phone number. They showed up 2 business days later, looked at my washer, verified the code along with the Model and Serial #s, telling me it was the control panel. I gave that information to them on a Friday, they showed up on a Tuesday. They knew what that code was and what it meant for that make and model washer, but there just had to be a service call in there. The part was ordered on that Tuesday... here it is the following Saturday and the part still isnt here. I do not understand what takes Whirlpool so long to ship the part. Do they not care that in this hustle bustle life we live in, we dont have time to wait for a part that may or may not show up. Ship it overnight. That is an option. Making the parts accessible to the service people in a timely manner would make great customer-service. Better yet, how about going back to the old-style washers. This high-efficiency non-sense is highly expensive.

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

Whirlpool Gold with bottom freezer, had it for about eight years and no problems. Great seal and great storage space. Also plenty of space in the freezer. We are a family of four. It is extremely quiet. There is flexibility as to how to mount the shelves and they are easy to clean. I have never had any spoilage.

Whirlpool gold series bottom freezer unit - We have had numerous problems with this refrigerator. We have had several repairs done on it and have still not solved the problem. The defroster does not work right and we have to unplug it so it will unthaw, then the refrigerator gets cold again. The freezer when it is acting up freezes food and ice cream so hard it is inedible. We have just purchased a different refrigerator. This Whirlpool model has also been discontinued from what I can find. No doubt because of a design flaw. Why are they not responsible for this? We bought this appliance in good faith.

Our just over 1 year old Whirlpool washer died completely last month (mid May). After calling them and being directed to the extended warranty dept (which we ended up purchasing), a repair guy came out and told us it was our main controller board. Three days later, he returned with the board and nothing. We were then told it was the user interface. They were on backorder until June 5, which means our machine would be out of commission for three weeks. I just received another call informing us the part was now on backorder until June 15. Whirlpool, on what planet is it acceptable for your appliances to be out of commission for six full weeks? Never again.