The Whirlpool range #GY398LXPQ00 is four years old. This is the fourth major problem. Oven overheats and will not function. I set it at 350 and the bottom coil and broiler both came on and overheat quickly. This is the third time with same problem. I am going to have enough invested in repairs to buy another range. I shall never purchase another item made by Whirlpool or any of its affiliates. That leaves me with Samsung or Bosch, I think. The people are very curt and offered no help at all so calling them is extremely useless. This range is definitely a lemon. Too bad, there arent avenues to make them replace it. I am angry, disappointed, and disgusted. Are you listening, Whirlpool? Never again. May your company go down the drain.

I thank the folks at Whirlpool for building a washer (Cabrio tub bearing failure) that lasted 22 days just shy of four years, better than the Whirlpool Duet that lasted 14 months, tub bearing failure also. Now I have high confidence that Whirlpool pre-engineers failure into every washer they build.

I purchased a very expensive Cabrio top-loading washer thinking I would never have to worry because supposedly it’s the top of the line, right? Well, I have it a few years; the first week they replaced the basket because it was ruining my clothes. And then I had to replace the pump because of a coin getting caught and putting a hole in the pump. Really? What the heck? Now the basket is all shredded at the top. Obviously that isn’t right, so what do I do now? Replace the basket again? Who gives them the right to charge so much for a piece of junk? Plus, it’s supposed to save on water, but I feel that the clothes don’t really clean well. They hardly feel wet coming out of the machine.

We have had every issue with our Cabrio model 6600 SB2 that Kimber of Salem, VA has had. Thankfully, we purchased an extended warranty at time of purchase(1-31-07) from Lowes or repair costs would have totaled more that the price of the washer, which was $900.00.It is now making a loud noise during spin cycle that sounds like a bearing going out. It is 1 month from being out of the 4 year extended warranty and today, 12-26-11, the repairman has told me that the washer needs to be rebuilt. The washer itself, does not clean that well and the clothes are so wrinkled when they come out, that the dryer cannot get the wrinkles out, so everything needs to be ironed. What a pain!We bought this washer because Consumer Reports magazine listed it as a best buy. This is not the first recommendation Ive chosen because of their magazine that I was disappointed with. I have lost faith in them. I would not recommend this washer to anyone. The matching dryer, however, has been trouble free.

We bought the Whirlpool water heater and not long after, it quit heating. After many phone calls, we finally got a response and were told to get the replacement thermocouple. We did this and it was the wrong part. We found out that we had to have a right hand thread thermocouple. Now, the heater is out of warranty and we cannot keep it lit at all. It takes at least 3-4 times before it will light once and then it goes out every time the hot water is used.

I bought a WDT 720PADW2 dishwasher 15 months ago from Home Depot. In the last few months, it has begun to rust at the vent above the the handle. Whirlpool will not address the issue because it is out of the 12 month warranty period, yet is obviously a design flaw.

My Whirlpool Cabrio Washer is only 4 years old. I have had balancing & spin issues since day one. Thought it was just me. Constantly had to drain and spin after rebalancing. Now 10 days ago it cost me $250 to have it fixed. The aqcuator (?) Went. It wouldnt spin out. Now 10 days later it stops again. The appliance guy reads code. F7E7. He tells me the bearings are no good. Will cost another $400 and they need some special tool to fix it. IM DONE. My last set was 15 years old. The price is ridiculous and quality not worth what this triple capacity set cost.

My oven was 11 months old when I tried to use the self-clean cycle for the first time. 2 hours into the 4 hour cycle, the oven completely shut down, door locked shut and no lights on the control panel. The repair tech came out on a warranty repair call (no charge), explained that Whirlpool does not use a thermal protector rated for a self-cleaning oven and that it blows every time. He then proceeded to replace it with the same thing because he is only allowed to put in the recommended part, which is not rated for the high temp cleaning cycle. So the oven is usable, but not the self-clean. Since I am at the end of the 1 yr warranty period, even if I were able to get Whirlpool to replace the oven (ha!) there would be no warranty because I only get the original time limit. So if I had a new oven and it blew out, it would not be under warranty for fix/replace. The repair tech said this is a COMMON problem with Whirlpool self-clean.

After 3 short years, my dryer that cost me over $900 is not working and the part needed for the repair is no longer being manufactured. They did offer the parts for free, but that was useless since they arent available. They then offered me a new dryer which would cost me $800. I am currently waiting for the Product Exchange Team to contact me. Im not hopeful that will be of any use.

WRF989SDAB00 - Our house burnt down in April 2012. We purchased all Whirlpool products to be put back into our house. We had to purchase these items in November 2012 so the contractor could get them into our house because of the cabinets. We did not move into our house until the last week of December and could not use these items until then. In December of 2013, our freezer went out along with the ice maker. I had to fight for Whirlpool to pay for these repairs. They kept saying that it was over the one year warranty. They did accept responsibility and paid for A&E to come look at the frig. One guy came out the first time and thought he fixed it. No. A month later two guys came out. They said it was the condenser. They ordered the parts and came back a third time to replace it. A month and a half later, same problem. A&E came out a fourth time and thought they fixed it again. Nope. During this period, I purchased a extended service plan. I AM TELLING EVERYONE TO DO THIS NOW BECAUSE IT TAKES 60 DAYS FOR THIS PLAN TO TAKE EFFECT. Now the service plan people sent a different company out and he said it is going to cost a lot of money because the things that need to be replaced. The plan SHOULD cover all of this. I called both the service company and Whirlpool demanding that they send us a replacement frig. I believe sending someone out at least SIX TIMES to fix the same problem is ridiculous. Each company is blaming the other and each is saying its the others responsibility to replace the frig.

I purchased a washer model# wtw560xw, serial# c04830040 on 1/11/11. This product has never properly washed clothes. I have had 3 technicians come out and press buttons on my machine. The most recent supervisor I spoke w is Niki id# **. She said that the machine washes but is not supposed to clean clothes. I am getting blown off and aggravated. I filed a complaint with BBB that went nowhere. Someone from the corporate office named Amanda called me and told me she would look into it and a week and a half later, not return my call. I had to track her down for her to tell me she can do nothing! The hold times are always extended. I have a pile of ruined clothes and a pile that I am attempting to hand wash. I am beyond frustrated and need a machine that will wash my clothes. I am not in the 1800s. I should not be hand washing when I paid hundreds of dollars for this useless machine. I am ready to file a class action suit. I can be contacted at ** **.

Weve owned this refrigerator for about 6 weeks now. It is a 23 cu. ft. model with a bottom freezer. It is working great, and we have no problems with temperature control in either the refrigerator or freezer sections.

I purchased Whirlpool 6.2ct electric range on 3/16/2013 from Lowes, Fremont, CA. I tried to bake my cake on 11/19/2013, and preheat it to 400F degree. When the temperature achieved to 400 degree, I put my cake in not even 5 minutes and go to dining room to pick up something. When I turn around, I saw the oven window is so bright and I open the door right away, it has fire from the left side bottom. I turn off the power right away but still has big fire. So I use the fire extinguisher to get the fire off.I went to Lowes to complain, this product is still under the manufacture warranty and I also purchased two years extended warranty from the store. Lowes sent the 3rd party technician over to check, they open the bottom element and insist I drop something to catch on fire. He tried 350F degree is working. But the fact is, theres nothing dropped, no oil, water or and any ingredients, only fire extinguisher powder all over the bottom. Technician put back the cover, I asked him, How do I clean up the bottom extinguisher mess? He said, You dont need to, just clean the top, and wont try 400F degree for me since the top didnt clean up. I asked him, I am so fear to use it now, you asked me to clean it up and try again. I only use my oven to bake cakes, cookies, and muffins, and that day the cake even not still raise yet. How could it catch on fire? Is this product defective? I doubt it.I also called Whirlpool, they said most likely its short circuit. They only provide the repair, unless it cant be repaired, then they replace it. Manufacturer also told me that my temperature is high. I dont think so. I have no problem to use any oven in 425-450 in the past. If this is high, why your stove has function to that high degree? I am so upset with both services. From my concern, nothing dropped to bottom and caught on fire. They all refused to replace the new one and asked me to continue using it. I really dont feel confident to use this one and dont know who can help me to replace it.

This is the worst washing machine Ive ever purchased. Bought 12/19. The water level never never goes up high enough, to cover the cloths. I have to add water no matter what setting. I hate that. The sensor isnt working. You arent able to adjust it yourself, its computerized. The water shuts off when you lift the lid so you cant rinse out the soap or fabric softener caps. I hate that. The lid locks when the rinse cycle starts so I have to unlock the lid to add fabric softener. Why lock the lid so soon, wait till its in spinning mode. Really really badly designed!!!! Will never buy anything by Whirlpool ever again!

Whirlpool 2 Cu. Ft. Stainless Steel Over-the-Range Microwave - My wife and I have just remodeled our kitchen and we bought all the Whirlpool appliances, fridge, stove and microwave. We have had them for about 3 weeks now and now the display on the microwave just stop working. I just cant believe this. Its going to be a real pain now to remove this and replace it. Has anybody else had this problem and I wonder if its even covered under its warranty.

I have had no issues with my washing machine. Love the different settings. Washes clothes well. Dryer has minor issues like the drying dial stopped moving so I need to manually turn it off. It’s more of an inconvenience, but for the price it should work.

Whirlpool 500galaxy gas water heater - First week ran great. Now Im lighting every day. Called Whirlpool and just getting run around. Had it a month today, still lighting every day. Cant afford to buy another.

On December 24, I was planning my annual Christmas Eve dinner when my oven just decided to quit working completely. This was the third time my oven broke down on me. I called Whirlpool and they pretty much told me theyll get to me when they can but it was the holiday. So I understood that it would be a few days. I had a technician come out to my house on December 27 and tell me that he needed to order a fuse. He called all over the state to find one but no one had one so he put it as an emergency. The technician did everything he could to accommodate me but could only do so much. So I waited and waited but heard nothing.Today, January 3, I called the department to see when my part was going to be here and they tell me January 10 - unacceptable. I called the management team and spoke with Tiffany who pretty much just told me, Sorry. You have to wait five business days to find out if the part is available. If not, then we can discuss sending new ovens. Why would we have to wait five business days from January 3 when it was ordered on December 27? Look, Im a very reasonable woman and this is the first time I have ever complained online about a company. But I have gone 10 days without an oven and I have a family that I cook for daily.My ovens are four months old so this should not be happening. And when it does, there should be parts to fix it or a replacement on hand because no family should have to go without an oven when they just paid a ** load of money for it. Customer Service should be a little more sympathetic and a little less about business because at the end of the day, theyre not the ones suffering, we are. Also if this part is on back order, that tells me that this probably happens often. Maybe Whirlpool should recall this oven model because whoever heard of an oven overheating? Get it together. I will spread the word of mouth about my experience!

I have never had such a horrible experience in my life as I have with Whirlpool. Refrigerator ($2,500) broke within three months, and then broke again another two months later and hasn’t worked right since. They have the most horrible customer service, parts are on back order, I’ve had to throw away hundreds of dollars worth of food because everything keeps freezing but they do not care. Ice machine has been broken for over a month for the second time. They are the worst company I’ve ever dealt with. Buyer beware. Do not buy anything from this company. Their products are the worst and they have zero customer service. Good luck if you buy something and it breaks. You might as well just buy a completely new appliance.

I purchased my Whirlpool side by side refrigerator approximately 6 months ago. Immediately upon delivery the compressor showed itself to be very noisy, especially upon start up. I questioned the delivery persons and was told it would become quieter with time. It did I not. In fact, in the following days it got worse. I contacted Whirlpool and was sent an “approved” repairman. The confusions and scheduling difficulties in this process, however, were many. Finally, when the man did arrive. He listened and said the refrigerator was working but agreed it was loud but apologized there was nothing he could do.I called Whirlpool again several times to note the noise and constantly was given the sympathy of people saying they “understood but there was nothing they could do.” Finally, out of desperation I contacted the store where I had purchased the refrigerator and they sent a manager who agreed the unit was unreasonably loud and took the refrigerator back. I researched the Whirlpool company and found they are essentially the same company that makes several other common American name brands, so I made a point not to purchase from any of these companies. Instead, I purchased from a foreign manufacturer and couldn’t be happier. All I can say is I tried to buy American but have been greatly disappointed by both the product and lack of customer service by Whirlpool. I will not buy from them or their other companies again.

Whirlpool Cabrio WTW5600XW - Bought the washer/dryer set on May 13, 2011. The dryer has not given me any trouble. The washer on the other hand has been awful! From the very beginning, I noticed the washer was not getting my familys clothes clean! If one of my children had gotten anything at all on their clothes, I would have to wash about 5 items of clothing to even have a chance to get it clean! Doing this did not always work! I usually send my really dirty clothes to my mother for her to wash in her old style washing machine with an actual agitator! They always came out clean when she washed them! Also, please do not attempt to wash comforters, sheets or any bedding in this washing machine. It does not clean them! When you take them out, they smell worse than when you washed them and have wet and dry spots all over! Oh, and they are still dirty! It is now May 8, 2013 and my washing machine does not wash or agitate anymore! I called Whirlpool and they can only offer 2 options. A repairman for Whirlpool in my area will come out for $129 to diagnose what is wrong. This price does not include parts or labor! My other option is a flat $300 where this will pay for everything along with a 1 year extended warranty. So with the $300 option, this will put me paying about $1,000 for my washing machine! This is ridiculous. My washing machine is only 2 years old. I should not have to be repairing already! Do not buy this washing machine. If you do, definitely purchase the extended warranty and be ready to use it!

I purchased a Whirlpool duet front load washer 1/2013 new from Lowes. In 5 yrs it is my 2nd washer of Whirlpool. After 2 1/2 yrs, the bearings have gone out, also every time I run the cleaning cycle, water leaks out under the washer. My boyfriend looked the parts to fix the washer, since I called Lowes concerning the warranty and its out. Cost to repair, just in parts would be around $400, I paid a lot of money for a product to last only 2 1/2 yrs. Such a lack of quality in workmanship. With these price, there should be better quality. Do not purchase a whirlpool. 2 washers for them in 5 yrs is not a great track record.

I am extremely disappointed in my new Whirlpool washer dryer matched set. My washer started to leak at less than 6 months of age, and my clothes are extremely wrinkled due to excessive spin and smell absolutely foul. I have adjusted the spin cycle to the lowest setting to prevent wrinkling as suggested in the product materials. I have cleaned the washer with the recommended product on the clean washer setting, although now with the leak, that means a good floor mopping too!I have contacted customer service about the leak since the machine is still under warranty - and they gave me a 4-hour window on a specified day for the service. I took the time off work and the technician failed to show. I called twice to follow up on his whereabouts and ETA. They did nothing except tell me to keep waiting. 45 minutes after the outside hour of arrival had passed, I called again. The customer service offered to make me another appointment so I could take another half day off work and hope he would show up the next time. When I asked for a preferential booking (with a real time) to minimize taking more time off work, the manager said all she could do was give me another 4-hour window. I said that was really bad service and she hung up on me! Another rep did do a little better - he sent me a name and number and said I could try to book an appointment directly and hopefully minimize the additional time off. Its the last Whirlpool appliance Ill buy - with that kind of customer service, Id rather be out pounding my laundry on a rock.

I chose this dishwasher with stainless steel exterior to match other appliances in the kitchen. It functions very well and has for years. Very easy to keep clean. The interior shows no wear and the racks provided make it easy to arrange the dishes and silverware.

I purchased an HIE washer one year ago this month. I have never been happy with the cleanliness of the clothes when they came out of the wash. The only way to get them moderately clean is to wash a few items at a time and even then the whites, especially socks, seem dingy. I noticed the new Whirlpool washers now have an extra setting to add more water to the machine, so the executives have realized there is a problem with the original model.I think Whirlpool should give all customers who previously purchased the models without this feature a trade-in option to get the newer model that fills with more water or for another model with the full spindle that has worked well for so many years. I have been very unhappy with the performance of this washer and would only hope the executives would do something to resolve this problem and satisfy previous customers.

I purchased the Cabrio washer/dryer in 2006. We have had it repaired 6 times and I even purchased a two year extended warranty after having issues with it the first year. Now I seem to be in the same boat. The washer will not spin and drain. This has already been looked at by a technician several months ago. I feel like this product is faulty and has not worked properly from the start. Are there lemon laws for appliances? It seems that this product would qualify. I will never purchase Whirlpool again.

Do not bother purchasing Whirlpool refrigerators. Bought mine new in November. The paint on the exterior has been chipping. They inform me that its a cosmetic issue and that they are not going to repair it. They told me to use touch up paint. The paint has chipped more than once and Im afraid this is going to be an ongoing issue. Its obviously a product defect (my last fridge lasted 27 years without incident). I dont do business with companies who dont stand behind the products they manufacture. These days its all about get their money and the hell with them once we do. Last time I purchase anything Whirlpool.

I purchased the Whirlpool washer in February 2019 and delivery was in March. As stated in my previous reviews for the manufacturer, and subsequent repair calls, three; from the first time using the washer, it didnt fill properly for the amount of the clothes in it. A piece of paper towel never got wet through the whole wash cycle. I had to resort to raising & lowering the lid numerous times to get to the correct water level; adding water with a container or just pressing down on the switch under the top cover; 4-5 count. Needless to say very time consuming. As for hot water for doing white clothes, forget about it! It seem to me its the same problems with this whirlpool washer thats been happening with most of the other reviewers/purchasers. Did Whirlpool ever think about taken back one of these problem washers and checking it out for themselves? Maybe installing a clear plastic lid to monitor water levels at different wash cycles? Hot water temps when called for? Are these negative reviews ever seen by Whirlpool? Or in the trade is it called.... JOB SECURITY? Any more detail required? Cabo

Called Whirlpool customer care for help with identifying make and model number of a slide-in, ceramic cook-top range (one of their popular brands). The representative was cordial, patient and very helpful when it came to giving me directions on how to locate make/model information on the unit. That was until I let her know about a recent problem with the stove. The edge of the cooktop is much too sharp! My hand got cut while wiping down the stove top/adjacent counter. Although Ive had the stove for a while, Id never had that happen before; thats probably because I used a thin rag this time around to do the cleaning. I asked the rep if anyone else had reported getting cut by the stove top. She said, No. I let her know that my goal was to just them know about the situation, because such a sharp edge on a cooktop is a safety issue. She disagreed. But what could or should she have said? In all fairness, it came down to balancing loyalty to the company with genuine care for the customer.I do appreciate how kind she was in communicating with me, but am very displeased that once Id shared about the problem she seemed rather dismissive of the situation. How could the risk of being cut NOT be a product safety issue??? If you visit the Consumer Products Safety Commission website, you can see where risk of laceration is a reason some products are recalled. Based on that understanding, I would say that sharp edges on a ceramic cooktop IS a safety issue!

Whirlpool Cabrio Platinum Washer - The seal on the top of the drum is breaking down. It is cracking at the bleach and soap dispenser. Somewhere in the washer drum or plate is causing holes and cuts in the clothes. The machine is only 2 years old.

They really dont make them like they use to, do they? This Whirlpool Cabrio aka Caprio has given us problems for the past 3 years, weve owned it for 5 years. It doesnt matter how much, or how little clothing you put in this washer machine. It will start going NUTS, Thudding, Banging against the inside of itself, completely out of whack, and then it will show a UL where the time is shown. Every time we do laundry this happens, and we have to stick our hands in the hot water and reorganize the clothes, and pull more and more clothes out till theres only about 3 items of clothing left! This washer is GARBAGE! I advise people to keep away from it. The washer we had in the past lasted us years upon years. These washers of now in days are Crap Garbage. Keep the fancy tech look, and give me the old fashion Knobs ANY DAY! Whirlpool brand is Not what it once was.

I bought a Whirlpool water heater from Lowes. I had trouble with it from day 1. It never worked correctly. Their service department is terrible. All they want to do is sell you extended coverage policies on it. Every time I have it fixed, its never covered, and I have to pay again. You will be sorry if you buy a Whirlpool water heater.

I bought a complete kitchen set of the Whirlpool Gold Series Appliance from Brand-Smart in 2/2013. The first problem I had was the compressor on the refrigerator. It started making a noise & stopped cooling in 04/2014. I called Whirlpool and they said there was only a year warranty on parts and service. I was not notified that I could get an ext. warranty. Therefore I will have to pay for the repair. I called a service tech out and he said I needed a new compressor, total cost 255.00. Then in 11/2014 it started making the same noise & stopped cooling another $255.00. Now its doing the same thing. It needs another compressor, will cost me $255.00 more! A total of $765.00!! And I have only had the refrigerator 2 years 2/2015.

Shortly after the warranty expired my refrigerator started building ice on the floor of the freezer. With the build-up of ice the freezer started leaking on the bottom. Sometimes it gets so bad I have a hard time closing the freezer door properly. The Model# GB9FHDXWS06, Serial# K31505096 of my Whirlpool refrigerator. I do not recommend any Whirlpool product. Do your research before you buy any Whirlpool product.

We bought our Cabrio set 2 yrs ago. They have worked fine, until about 4 weeks ago when we begun getting what looks like bleach stains on our dark and colored clothes. I blamed my wife for using bleach or splashing it accidentally. So today it happened again, and no bleach was used or even open near the machine. This was the third load today and the first one was towels, no damage, 2nd load whites and light underwear with some spotting, third load pair of pants and pair of shorts ruined. What is happening?

Whirlpool Washer WTW8700EC + Dryer WGD8700EC. Bought to replace a 35-year-old Whirlpool set that is still working and had no repairs in that 35 years of ownership. Gave to family member and its working well. Was not a cheap item but well worth the money. It performs beautifully. I chose Whirlpool. It is a proven brand with a long history of reliability. When I bought my last Whirlpool, I bought the top of the line model washer and dryer. They say you get what you pay for and that holds true in my case as has with many others who believe it! So this time I did the same thing and bought the best top loader they had. It has many options I still need to learn. I just use it like the old machine and dont need to worry about types of fabrics or making mistakes. Just follow the instructions for detergent and softeners and all is good. This machine cleans as great as the old one without beating the clothes to death. New agitator design keeps from paddling the clothes, so I dont need to use the gentle cycle or medium to preserve the clothes. The dryer I can say is most efficient as I noticed it took far less time to dry, and notice a small drop in my electric bill and gas bill. I think this will be my last machine ever needed. I do take care of my things and I do clean and polish my machines, they are an investment like a car or house. Front loaders have a lot of problems with leaks from the doors. Will stick with top load only!

I have a front load Whirlpool Washer and it has leaked within 6 months of having it. The rubber piece was replaced and it still leaked. Whirlpool wont take responsibility for its product. I have to put towels down around the washer every time I use it because it leaks. I purchased this because it is more economical to use a front load but not when water is leaking from the washer.

I got a new Whirlpool washing machine and dryer last year and Im very happy with both. I like the fact that it offers a quick cycle if you have a small load or need something quickly. If youre debating on what brand of washing machine you should buy I highly recommend Whirlpool or the other brands because Ive had really good luck with mine.

We purchased this Whirlpool pair after our upright machine was unable to be repaired... because of parts coming from China and being hard, if not, impossible to get. We have had this pair for about 2 years now (Lowe’s). It still doesnt clean the clothes and it continually goes off balance when doing sheets, comforters etc. Myself I feel since they have taken the middle agitator out of the machine - it no longer performs the way a washer should and that its main function is to get the clothes clean! I did write a letter to Whirlpool about it and they pretty much told me, “Well too bad.” So much for buying American made products... at least the upright did last 6 years!

I have always used Whirlpool products and have grown up with them. From washing machines to dishwashers. Not only is it made in the USA but its reliable. The only problem is space and it can do with more freezer space. Other than that its a great refrigerator.

I purchased a Whirlpool Cabrio washer in 2007 and had to replace the control panel for $300 each time twice.

For the most part, the dishwasher performs well, but I wish they would ask the input of women when designing appliances. I just can’t figure out how having spikes on the top and the bottom racks is supposed to help in organizing your dishes better for proper cleaning.

We have just built a new home and have spent a ton of money on appliances. I so wish I had looked up the reviews on this Whirlpool Cabrio Washer before we bought it. It makes a very loud annoying sound through at least a third of the cycle (which I was just told by Whirlpool is the normal agitating sound). We have also had to have service out here twice in the first few months because some of the clothes come out dirty in areas that were folded over because of lack of water even on the high water setting. It also, ripped my favorite white blouse right in half. Trust me DONT buy it, you will be sorry.

I purchased a Whirlpool refrigerator for my condo in February of 2012. During the past six months it started to freeze everything in the food compartment, and then during this past month the freezer started to slowly die. Ice cream became soup. After calling repair and examination it appears the fridge has basically died and it would have cost me over $500 to fix a $570 refrigerator. That type of lifespan is unacceptable. Before energy efficiency demands from the government, refrigerators lasted much longer. In the 50s, 60s, the refrigerator my parents owed lasted nearly 30 years. Am I expecting too much? Apparently so. I went out and purchased a Frigidaire this time. Hopefully, Ill get a few more years out of that one (Not happy).

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

I purchased a brand new 2019 Whirlpool side by side refrigerator in October of 2019 for my new house. Yes, that was 2.5 years ago. HOWEVER, I live alone and hardly ever use the ice dispenser. Maybe, it was used 20 times in 2 years. The ice dispenser just stopped working and today I notice the refrigerator is not even making ice! What a piece of garbage!

Whirlpool - good price for pair. I have had this pair for over 10 years and they work good and are reliable even though they were not the top of the line models. Large capacity is a must - energy efficient is also a must. Discounts are nice to get but if not available I will go with a name brand. I want a washer with an agitator not one of the new ones that dont have one. Reliability is the most important factor so repairs are not needed. I want a full size washer with several cycles and all cycles have a cold rinse to save energy. Having a center agitator is a must - cant stand the newer ones.

The refrigerator does what it is supposed to do. The fact that I had to have it repaired only after 1 year of ownership confounds me. The space in this side by side is a bit crampy. Seems like Im always shuffling things around. I truly believe that Whirlpool made the condensation tray underneath the unit out of cardboard. It literally disintegrated and started leaking after about a year and it was 200.00 to have it replaced by a repairman. The water filters always tend to piddle on the floor too. At least I hope thats what it is, and not another wilted tray!

We recently purchased a new Whirlpool refrigerator and washer/dryer set from Home Depot. The truck for delivery was late and unable to pick up the refrigerator in time for scheduled delivery. Whirlpool contacted us to inform that it was now on back order for another week claiming there was nothing else they could do. Strike one. We paid for the installation and kit for the washer and dryer set. The tech who delivered them claimed the kit was not correct and that he could not install the dryer. We contacted Home Depot, Whirlpool, and had Home Depot call Whirlpool on our behalf with no resolution. They will not refund the installation even though they didn’t install anything.Whirlpool will not directly say whether or not they will send someone else out to actually install it this time. To top it off - I asked the Whirlpool rep which kit needs to be used and she told me whichever I want... for a gas hook up... whichever I want. This is ridiculous and Whirlpool has the worst customer service I have ever experienced. Side note - don’t waste time on the chat feature they provide. You will be directed back to the 800 number with 30 minute hold times. Horrible company!

What a POS. Havent even used the thing to cook a meal yet and already some chunk of metal fell out from the port at the top left inside the oven (behind the vent). It was clearly cheap pot metal. What else is this thing made out of?

I had ancient appliances (refrigerator, microwave, range, and dishwasher) that were all mismatched and were in the house when I purchased it in the mid 1990s. I saved up my money and even though my old appliances were working fine, I wanted stainless steel and everything to match so I decided to go ahead and replace my refrigerator, microwave, range, and dishwasher. I decided on Whirlpool since the company has been making appliances for many years and I thought they made a good product. I bought those appliances in 2012.In 2015, the microwave started to malfunction. At first, it would light up and act as though it was working, but it wasnt. I had it repaired - they said it was a fuse - and the fuse repair cost me about $75.00. It worked for about 2-weeks. I called the repair guy back and they didnt charge me, thinking it was something they did wrong when they fixed it. This time it worked for about a week when it went out again. Not wanting to miss any more work waiting on a repair guy, I went to Lowes and bought a pack of the appropriate microwave fuses and replaced the fuse myself. This time it worked about three weeks - I noticed it was popcorn that seemed to kill the microwave. I finally gave up repairing it when I used up all the fuses in the pack from Lowes. I bought a GE Microwave and it has been a dream. It does a better job all around and looks a lot better than the Whirlpool. I no longer have matching appliances but at least they work!But thats not all. Now the Whirlpool refrigerator has been slowly dying. It has been groaning and creaking since I had it installed but it has gotten so loud that I have to sleep with white noise so that it doesnt wake me up. Yesterday, I took out a Drumstick ice cream cone from the freezer - they are the cones that have chocolate covered ice cream with nuts. I bit into the chocolate coating and the ice cream all spilled out like milk! Looks like Whirlpool struck again and I am not even going to bother to repair it. I just hope I dont get food poisoning until I can get it replaced. And...the dishwasher. Well, it wont dispense the Jet Dry liquid if I fill up the reservoir. I have to fill it only half way or it wont work. I had to use an eyedropper to get the tank down to half. It doesnt really get the dishes clean either. My 20+ year old one I got rid of was 100% better than this Whirlpool dishwasher.Luckily, I hardly ever use the range...and when I do, its a burner or two so I havent had any problem with it yet. I am thinking of replacing it anyway simply because I dont want - ever - anything that says Whirlpool in my home. I was so excited when I decided to buy new appliances. I was finally going to have something new and nice in my home...or so I thought. Instead I wasted my money and got aggravation instead of joy. I dont know about others but I will never buy Whirlpool appliances again- never ever. And now I feel like my money was stolen from me -- and my joy definitely was stolen.

Received power bill and it had doubled. Went straight to water heater. Bought water heater 02/11/2011 and 12/25/2013. The brain they call it on top of the heater has a screw that has blown through the metal plate.They do not sell this type of heater at the stores so this must be a problem with all this type heater.

Model #wfw70hebw Duet washer. Lasted 18 months, replaced one sensor and then find out computer board is toast. Seems this was an issue as I was told there is a CORE deposit on the old board so it can be repaired and resold. WTF? New board (repaired) is almost $300. That is a bunch of bull.

In a recent decision regarding the highly expensive, supposed elite performing Whirlpool Gold refrigerators, a group of unsatisfied Whirlpool owners who are tired of cleaning water puddles from in front of their new refrigerators have hired all automobile corporations to manufacture cars only available to the CEO, Executive Board as well as the entire engineering staff at Whirlpool.These cars will be guaranteed to run ok. However, once the car is heated up under normal working conditions, the cars will be guaranteed to leak oil all over whatever surface they are parked upon. We hope that this will not be an inconvenience to the CEO of Whirlpool; however, perhaps once you have destroyed your new garage floor, you will understand the nature of our complaint with your poorly designed and engineered Whirlpool product.While this letter will have no effect on my current defective product provided to me by Whirlpool, it makes me feel better and I have not had the attention span to listen to my wife complain while she is cleaning up yet another (whirl) pool underneath our fridge.

I had an addition added to my home in 9/2007, which included a new bathroom. A whirlpool hot water tank was added. This week, I woke up to no hot water, so I called the whirlpool customer number regarding the warranty on the model FG1F4034T3NOV. T hey told me the serial number shows its out of warranty, although I may have only had it since 2007. They also said there was a screen that needed to be clean under the bottom of, it that if not clean, would make it stop working. Since homeowners where not cleaning it, they have made a replacement door part that would fix it, and do away with the problem, but I would have to pay $35 for it. I asked them, since the serial number shows that the part has not been replaced on this unit, why not just send it to me, and I pay to have it put on. The person said no, you will have to pay for it if I wanted the part to fix it . Although my builder did not give me the receipt for it, thats just not right. If a manufacturer knows they are having problems with their product, which require a part replacement, and they have produced one, they should be willing to give the part to everyone with the product that request it. On top of that, this model has the left hand threaded thermocouple, which no one around seems to carry. I am totally disappointed with Whirlpool, and right now would not consider buying, or have any more of their products installed into my home.

I bought a Whirlpool washing machine, model WTW4855HW, and was I ever shocked at how noisy it was. The wash cycle had a grinding noise that was just too much. After 2 loads I sent it back and didnt regret having to pay the restocking fee. I just couldnt believe that with all the technology we have today, that they couldnt build a quiet machine. Im an engineer so I know there are methods through gearing, belts, soundproofing, etc, to produce a quiet machine. Remember the dishwasher of days gone by. You couldnt watch TV with the dishwasher going. Nowadays, you can stand in the kitchen and have a nice conversation with it running. The technology exists. As a matter of a fact, my old Maytag that finally went bad after 10 years was fairly quiet. So, if you dont have your washing machine in the garage or basement room where you can close the door, dont buy this machine! Bruce in Portland

I’ve had my washer and dryer for a long time and it has been okay and it’s time to update. It has had its up and down and I may get another just after a while they are outdated and better appliances come along. Smarter people are making smarter things.

11 months after purchasing my Whirlpool 40 Gal Gas Water Heater N40T61-343 I woke to cold water one morning and found the LED flashing 4 times - high temperature shutdown. Unable to find any reset I called Whirlpool and after a couple questions, was sent a replacement control unit. Happily it arrived 2 days later. I was told then that it was because I had residue in the tank. I had no idea how he determined that because none of his questions even touched on that. Anyway, I had hot water.Nearly a year later now to the day and again I have no hot water. This time the pilot burns very weakly when I try to light it and then goes out. After three attempts I get 7 flashes on the LED - Gas Control Valve Failure, part of the same unit I replaced a year ago. Am calling tomorrow since its too late to go through any tech support steps over the phone that Im reading about on this site and seeing on Youtube. Honestly, I didnt replace the last heater because I had nothing better to do than replace parts on this one annually. No, I will not purchase another Whirlpool unit especially after reading all of the similar if not identical issues others are having.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

I just replaced a 4 year Cabiro washer with a Samsung. The washer was making terrible loud noise when spinning. It sounded like a jet plane. The repairman said it was a bearing that was going out and that it was a common problem in the Cabiro washers. Cost to repair it would be $500.00. Last week, it finally started spewing oil from underneath so had to buy a new washer. I will never, ever buy anything made by Whirlpool. Whirlpool said it was off the one year warranty (duh) and they wouldnt help with repairs.

My Cabrio washer worked fine for approx 3 years. Within the last 9 mos there has been one repair/replacement issue after the other: pump, computer board, bearings, seal, etc. Whirlpool takes no responsibility. Worse purchase I ever made.

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

Why are the Whirlpool appliances so badly made that they are not fit for normal use? Are they buying substandard parts? Do ConsumerAffairs advocate for more robust, long lasting products, particularly with current sustainability concerns for the world? Having to buy a new motherboard and burners, cups and knobs after a couple of years of normal, careful use, is unacceptable, surely? The motherboard, burners and fitting charge is almost half the cost of a new appliance (gas range). Is this acceptable?

We got a deal on our stove/dishwasher combination, establishing a payment plan upon purchase. And as a bonus, when you have a brand name appliance like Whirlpool, that made us more secure with the purchase.

DO NOT BUY THIS MACHINE. Mine is less than 2 years old. First one month after warranty expired, the clear lid cracked...$350 to replace! Then a few days ago a rusted circuit board came apart and jammed up my washer. This should NEVER happen. I contacted customer service and they told me that they are not covering this problem and that the service call is $175 and cannot estimate the repair cost. They also could not send a repair person out for 5 days. The washer has not been repaired yet so I do not know the entire cost but it will be expensive!

Very disheartening to know that an established company such as Whirlpool does not stand behind their products or acknowledge known product defects. Based on the quantity of complaints logged on this site alone, Id think a recall would be required. Identical to other consumer posts within, we purchased the Cabrio Platinum washer/dryer set (WTW8000BW0). Exactly 24 months to the purchase date, jet planes began flying through our home with the noise concentrated in the laundry room. The dryer has been fine; however, the washer is a whole other issue. The bearings are shot (as many users have cited) and the noise is deafening... even with the laundry door closed, TV on high, dogs barking and flurry of activity in the kitchen! We made a switch to the Whirlpool brand 2yrs ago due to reputation and longevity. Ooops. Lesson learned and $700 out the window. Back to GEs. If youre reading this and concur with our review, just remember... customers always have a choice! Unfortunately, Whirlpool will figure this out the hard way. Just like other iconic brands... Smith-Corona, Blockbuster, Polaroid, Nokia, Saturn, Pontiac/Oldsmobile, Sony and many others. There is typically a reason a company offers tremendous sales incentives (price cut, rebate, special financing) to unload products. We found out why. Thanks for the memories Whirlpool!

My brother bought my 80-year-old mom this range so that she could bake all her delicious desserts with ease in a new beautiful oven. I was at her house visiting and saw that she was down on her hands and knees cleaning her SELF-CLEANING OVEN. She tried several times using the useless AQUALIFT FEATURE but to no avail. In this day and age with self-cleaning technology, WHY would Whirlpool install this unbelievable bad AQUALIFT cleaning feature? To see my poor mother scrubbing the inside of the oven like she did back in the 50s & 60s just completely appalling!! PLUS the top surface enamel is bubbling up with rust and the oven is only 2-3 years old. So we are trying to contact Best Buy to see if we can get a refund on this HORRIBLE appliance.

I had my Whirlpool Quiet Partner 11 Portable Dishwasher for less than a year when it started leaving dirt, food particles, and white cloudy film on my glasses and dishes in the top basket. It got so bad that we started to wash the dishes twice but it would not clean the dishes. We called a repairman out to see what the problem could be. He checked everything and told us nothing was wrong with the dishwasher and to clean it with CLR. We cleaned it with CLR twice and the dishes looked better with the first wash. The next wash was the same with leaving grit and dried food particles on the glasses. I am now washing my dishes by hand if I want to clean dishes. Can anyone tell me what is wrong with my dishwasher? I am ready to buy a new one but not a Whirlpool.

Whirlpool is a very good company and their products work very efficiently! If I had a choice to choose in a different type of washing machine I don’t think I could choose. Whirlpool is very reliable. Their older machines as well as their newer machines! They last pretty long. The dryer is dry very well as well as the washing machines agitate your clothes to get them clean.

Product: Whirlpool Gold Series, Model WRX988SIBM01: Purchased 2014 at Lowes. 2nd day after delivery, called Whirlpool, refrigerator not working properly, freezer drawer will not close, condensation on outside. Sent person that delivered the refrigerator to fix problem, freezer had frozen ice behind each drawer approximately 2 inches that would not allow drawers to close. Delivery person used hair dryer to melt ice and adjusted drawers. Still periodically have to physically remove ice build up to allow drawers in freezer to seal properly. Ice maker stopped working, makes no ice at all, ice comes from inside refrigerator not from freezer, bad design.Today woke up to freezer drawers completely thawed and had to throw away all food, panel shows temperature at -2*. All food thawed and unable to be cooked/used. Called Whirlpool could not send someone until next Tuesday (4 days). We are a family of 5 and cannot wait that long. Unfortunately have called 3 other appliance companies only to find that refrigerator has to be repaired by special technicians! This is our first Whirlpool, bought because made in America, have been very disappointed with our $2500.00 purchase. Not sure that we will ever purchase another Whirlpool product, our inclination will be to buy less expensive product and choose to replace as opposed to paying recurring service calls + parts and labor.

We bought a new Whirlpool refrigerator from Sears last summer --- and after experiencing some motor noise we thought this would be ok. We went away to Mexico for 4 months this past winter and this spring the noise seems to be much worse. It seems to have changed -- and we called Whirlpool and they would not help. They said we pay even though we bought this fridge less than a year ago. Consumers should be made aware that if your fridge is noisy you pay for any servicing - they only cover a malfunction. My fridge needs a professional to look at the cause of the loud motor noise.

I purchased a new Whirlpool Cabrio washer and it has been nothing but a headache. The machine constantly rips our clothes and stretches them beyond repair. Now, the washer keeps showing an F1 error code and I have to restart the machine three times to get it to start. It also stops in the middle of the cycle and I have to restart it. What a piece of garbage! I called Whirlpool several times and they do not stand behind their products. Do not buy Whirlpool. I filed a complaint with the Attorney General and I suggest anyone else having the same problems should do so. Maybe we can get this machine recalled.

This is about my Whirlpool washing machine that has abruptly stopped working. My Whirlpool washing machine was bought in 2013 and was running [absolutely] great until Tuesday October 3, 2017. I called customer service and they said it was out of warranty. My Whirlpool washing machine model number is: WTW48008Q0. Serial number is: C34923747. I do not have the money to get this machine fixed. I am already a struggling mom, working hard to pay bills and I am already falling behind on most of them. I just had death in my family and now the machine dies - well there seems to be no end to all of this. I would really appreciate Whirlpools help in getting my machine up and running again. I have been a loyal Whirlpool customer over the span of more than two decades. I am a Whirlpool fan. My past machines have lasted 12 plus years on upwards to 15 years each.Let me share exactly what my washing machine is doing: I went to wash clothes as usual the other day; the machine filled up and stopped abruptly - that was it! It did not spin but instead emptied the water without washing the clothes and made some loud chitty chitty bang bang noises before it was all over. I unplugged it after wasting a lot more water thinking that it might just suddenly start working. It did not start working again, it just continued its non-working status.My family has bought Whirlpool washing machines and dryers for years from Sears; we were totally satisfied with the products we purchased, however, this washing machine did not make the five year mark. I really do not know what is going on with the machine; what I do know is this - it stopped working and I would like to get it working again. Hopefully it is not defective by design. #WhirlpoolWasherDefectiveByDesign. I found Whirlpool washing machines to be very reliable and would love to continue my great relationship with Whirlpool.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

I have a Whirlpool Cabrio washer. It was great for almost year. After that it has been nothing but trouble. The body of the washer has rust coming through the paint and large areas that is so rusted that the paint has chipped off completely. A washer is expected to deal with water and not rust through the body. I have a 10-year old Ford truck without a speck of rust. Dont they undercoat? The circuit board has had to be replaced because of rust. I have to take several Q-tips and go under the cover to remove all the rust if I dont it gets rust stains on my clothes, which is impossible to remove. The customer service is non existent. They have left me on the line for over 40 minutes. I hang on only because it would be another hour or so of my time to get someone to answer. I was without a washer for a month while waiting for parts. Why dont they have parts for their products? I had to slop my way too dirty laundry mats 3 times a week as I do 2 to 3 loads a day.My washer is downstairs and stops and gives me the unbalanced message even when its not, running up and down the stairs several times to complete one load. I also get the F51 message for no perceivable reason. The extra rinse button only works 1/2 the time. This was an expensive washer ($1,000.00) and I feel that I deserve my money back. They are knowingly making an inferior product.

My washing machine is a front loader. Previously I would not have purchased one, but after using it for a year or so I have changed my mind. As long as I do not overload it my clothes come out perfectly clean using cold water, and partially dry so needing less drying time.

After 22 years, I replaced my Whirlpool, electric, 50 gallon water heater, due to age and it was still working well. Went to Lowe's and they do not carry Whirlpool any longer, so I purchased and installed an A.O. Smith water heater, electric, 50 gallon water heater, model ES12-50R55DV110. Hoping for as good a product now, as I had from my Whirlpool. Also, I installed myself.

Whirlpool anode rod went bad in 2 months. Called Whirlpool, would not stand behind warranty. Had previous hot water tank (not a Whirlpool) in for 10 years with same well and water conditions. Also noticed Whirlpool hot water tank is not nearly as efficient on energy use. Overall, this is a very poor water heater and even worse customer service to not replace a part that was under warranty.

I absolutely hate this Cabrio machine. This should be off the market. Shame on them for selling this. Salesman sold me a bill of goods on this washer and dryer. I have to wash some clothes 3x or hand wash. Whirlpool told me to use bulky or delicate cycles, as this puts more water into the machine so my clothes will rinse clean (doesnt work). When I wrote, they didnt even offer to make a service appointment. They know they have a bad product! I agree. Greed.

Two years ago, we bought a Whirlpool gas range, model WFG361LVQ2. The range-top grates were porcelain-coated, smooth and shiny. The range itself has worked flawlessly (Admittedly, it gets only light use in our elderly household, which consists of me and my wife). The only complaint I have is that the porcelain on the grates is failing. On one of the grates, its flaking off where the flame contacts with it during cooking (Photos attached). On another two, the porcelain has developed a surface roughness thats clearly a prelude to same type of damage as the first. The fourth grate still appears to be intact. The differences in damage is no doubt due to the different amount of use that each receives.When I called Whirlpool, a supervisor there told me that grates have no specific life expectancy, and that is true for plain metal grates as well has porcelain-coated grates. She also said that some chemicals can penetrate the porcelain and shorten its life. I told her we didnt use any chemicals on the grates, but only rarely used common kitchen scouring powder, and I cant imagine the powder or the chlorine in the powder could do that kind of damage.When I asked what it would cost to replace the four grates, she said $187. I told her the entire stove cost about $500, and it didnt make sense to pay almost $200 to buy grates every two years for the next thirty years. I told her that the grates on our previous (non-Whirlpool) range lasted the life of the range - about forty years. So I declined to purchase new grates, despite her offer of a one-time discount of 25%. Though the grates are becoming eyesores, theyre still perfectly usable. So Ill hang onto them until I can find some bare metal ones to replace them.

My induction cooktop totally failed to work two months after installation. Whirlpool sent a repairman who told us it was the main board. He also said he was unable to locate any of that part anywhere in his computer. We called Whirlpool via our store, Ikea. They apologized, asked for 48 hours to locate a part, then said they would replace the cooktop if they were unable to find out. Almost 48 hours later, they hadnt located it and denied any replacement option. The parts cost is over $800. The cooktop cost just over $900. Whirlpool reps would only read from a script of legal warranty jargon. Then they said they needed 5 to 7 days. We had a baby visiting - we needed our stove. To me, an apology would be replacing that unit if the part wasnt available, not a verbal statement. Fortunately, we had the phone # of a local Ikea manager who told us to bring the cooktop to the store as they had them in stock. They replaced it with a new one. Over the years of my long life, I have bought many Whirlpool products. Never again. I need a washer and dryer, and will not be purchasing any associated with the Whirlpool Corporation. Thanks to Ikea, though, for standing by their customers.

I have never posted a negative product review but must do so now. The refrigerator is 1 1/2 years old at most and has been well taken care of. I noticed today that the finish at either side of the bottom of each refrigerator door handle has a problem. I couldnt tell if the finish was pitting or is just discolored. I called customer service and expected that they would help, especially since we have an extended warranty. Representative number one told me that the extended warranty only covers problems that affect the function of the product. I spoke to her supervisor and then her supervisor. I got plenty of apologies but no support. I offered to send pictures, but they were not even interested in checking out the problem.After speaking to them, I took the handle off and I see now that the handle cut into some sort of film that exists on the metal. (I am not talking about the protective plastic coating that is on the the refrigerator at delivery.) The film is lifting off the surface and creating discoloration. If Whirlpool was at all concerned, I think this issue could be fixed with some sort of gasket to keep the metal handle from cutting into the surface. Im hoping the problem is static, but hard to say what will happen. If they had been interested in trying to understand the cause of the problem, it would have been easier to accept the limitations of the warranty. It would have demonstrated an interest in avoiding this problem for other consumers in the future. My last Whirlpool product. Period. Good luck if you decide to do business with them.

My microwave is a Whirlpool WMC10511AW purchased in Jan 2014 for $150. It is very light weight and moves around when opening and closing the door. I have to use something behind it on the counter top to keep from moving backward and causing problems getting things in and out. In the first year we had problems with the door latch, but after a while it stopped being a problem. I am used to the stability of Amana Radarange so these very lightweight microwaves seem really cheap to me. It works fine at this point but it seems that these really inexpensive countertop microwaves have to be replaced about every 2-3 years where an Amana which costs a lot more lasts for around 20 years and are very stable not moving around all the time.

We purchased our oven new in a package deal with the rest of our kitchen appliances four years ago. The bottom heating element in the oven has already stopped working. Every oven I have seen in my life has lasted a minimum of 15 years, and most 20. All I can say is DO NOT BUY WHIRLPOOL APPLIANCES! In the past 4 years, weve had the repair technician work on the Whirlpool refrigerator (once), dishwasher (3 times), and microwave (3 times). Now, the stove isnt working correctly, making this a total of 8 home visits by the Whirlpool repairman. Whirlpool is manufacturing trash for the landfill now, not quality lasting appliances.

My dishwasher interior and exterior is easy to keep clean. Very quiet and cleans all my dishes. The various cleaning options meet all of my needs. I would recommend this brand to everyone. I have had my dishwasher for 2 years and have had to call for service.

We bought our Whirlpool washer and dryer set through a PX at Fort Hood, Texas. Took it home, plugged it in and... nothing. Called the service desk, and they sent a repairman right away. He replaced the panel and the water intake fuse (I think? It was a fuse that dealt with the water filling) and then we were off and running. I thought, Great! Now I can wash laundry! After about a couple months, the washer would be so stinking loud in the spin cycle, we would plan outside activities ha ha. Fast forward 2 years, the loud sound continues, but Ive not had any problems. Then, Im washing a load of bed sheets, and just happen to walk past the washer while its spinning... I smelled something HOT and BURNING! Sure enough, it was the washer! I hurried and stopped the spin and unplugged the machine. Opened the door to pull out my sheets, and white smoke comes pouring out of the machine. IT NEARLY STARTED A HOUSE FIRE. I was praising God I smelled the problem. Who knows what would have happened. So I call an appliance shop I trust. They send out a guy who tells me I might as well purchase a new machine because the bearing is bad, and the repair is going to cost $600+. Never again, Whirlpool. Never again. You dont endanger my familys safety in exchange for a quick buck on cheap parts. Ridiculous. And, now that I am reading all these reviews on this website about my washer, I am floored. How is there not a class action lawsuit against this company? Mold and fire-hazards are serious infractions, in my opinion.

Apparently my machine, bought in 2011, was the first year they were made in the US. The washer has leaked soap down the front (a front loader) since day one. Service has come and replaced just about everything and its never helped. Its literally a piece of junk. Very disappointing. My older ones were great.

I purchased a Whirlpool 12-gallon point-of-use water heater as a booster when I was going to get a tankless and when we decided that we didnt need a tankless, I tried to get an RA number through the manufacturer so that the store could give me credit, as it says directly on the water heater, Do not return to store. They said there is nothing that they will do and it cant be returned to the store. So, what am I supposed to do with this water heater now? Before I knew this was going to happen, I purchased a 50-gallon Whirlpool water heater as well. So now, I have the 50-gallon that I have had to replace the element for already and I have only had it for less than a month and a half, and the 12-gallon is just sitting in my garage. Im completely irritated with this company and do not recommend anyone to go with this company! This is the worst customer service!

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

Their water heater is the worst ever! I will never buy another Whirlpool product. We purchased our water heater on January 17, 2010. We had to have the entire electronic system replaced in August 2011, including the lower element, control unit, thermisol, and electronic. Now, just a few short months later, the system is not working again, plus, the containment unit failed, flooding our basement. When we called Whirlpool, we were treated callously and rudely. Now, we have to pay to have the old unit removed, and a new one installed (they told us to throw it in our trunk and return it to Lowes, as if). Why did we pay to have this warranty when both the product, and the warranty are junk? Never, ever again! While Im at it, I should add that our range, and refrigerator are also made by Whirlpool, and those too, are pieces of junk. I guess were bucking up, and scheduling a new installation. If there are any further problems, I will be contacting an attorney.

My wife and I made the unfortunate mistake of purchasing the Whirlpool Gold Series, model #WRF989SDAM00 refrigerator two years ago...yes TWO YEARS AGO! We have experienced numerous issues with the appliance but our latest (no cold air in both the fridge and freezer) prompted a call to a service center. The serviceman that showed up knew immediately what the issue was, our compressor and evaporator had malfunctioned and according to him, We have seen the same problem in a number of these models and that Whirlpool has since redesigned the casing to prevent this issue in new models. What about those of us who purchased the previous model?! Now shame on us I guess for not purchasing the extended warranty...I suppose I just took it for granted that in todays competitive manufacturing world Whirlpool would be committed to building a quality product! Because of this I was offered two options from Whirlpool. #1 - pay for the parts yourself...over $800 or #2 - purchase their 1 year warranty program @ $350/year, this warranty will cover all parts and labor for an entire year. Based on my experiences though, I will need to purchase a 1 year warranty @ $350/year for the life of this lemon, potentially costing me $5500 over a 10 year period. I ultimately took option 3...tossed the piece of junk and bought a new fridge from their competition. Dont be fooled by the attractive design and appearance, the Whirlpool Gold Series refrigerator is a money pit waiting to happen!

I purchased 5 Whirlpool appliances when I remodelled my kitchen and am extremely disappointed with the quality and ability of them. The self-cleaning range (this phrase is a joke) has proven to be useless. I followed the cleaning direction according to the manufacturers direction even using the distilled water as indicated. The AquaLift self-clean did not clean the oven at all. It looks like I never turned the self-clean on. I gave up a great working GE self-cleaning oven that actually did clean itself. If I could afford to change this product for another brand I would do it in a heartbeat.

I purchased a Whirlpool water heater with the Flame Lock Safety System on 6/4/12. When installing the water heater, the cold water pipe would not screw into the top of the water heater. I exchanged this water heater for a new water heater of the same make and model. I brought this water heater home and had it installed and noticed that the flame on the burner was orange and too high. I called the 877-817-6750 number for warranty and was told by the customer service rep that it was either the gas regulator or the orifice inside the water heater. I was told to contact a plumber to take care of this issue and it was not a warranty claim and not their problem. I then went to the Lowes store where I purchased the unit and spoke to a manager. The manager called the same number I called and was told the same thing, that I was responsible for the repairs to the unit. How can this not be covered? Both pieces are internal to the unit and were never touched during installation. I now have to remove and return this unit and install a new water heater that will not be a Whirlpool at my own expense. Do not buy Whirlpool.

Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty. Spoke with manager, Tracy **. She said they would not help - out of warranty. Called local parts/service center - ea. hinge is $42 plus shipping and labor to install. Obviously this is a defective design. The lid is too heavy. I was having a difficult time deciding to spend 150-200 dollars every 2-3 years for hinges on a $700 washer and then I read all the other complaints about Whirlpool washers. I will sell it for scrap and buy a better brand.

Awful customer service. We bought a washing machine in 2010 and it has shredded a ton of clothes over the years. I called customer service to see what they could do to help me with this problem. After about 45 minutes of trying to get more than a service that I would have to be responsible for, the supervisor offered me a new washer at a discounted price. I went online to compare and found out I could purchase the exact same washing machine at home depot & best buy for $50 cheaper. I called back to see if there was anything they could have done and they would not budge.Shame on you Whirlpool. You have lost a customer and I will make sure no one I know buys one of your products ever again. I cannot believe that you would not make any accommodations for us. We bought that washing machine with the intention of keeping it for 15 years. It has cost us countless amounts of blankets, shirts, pants, etc. I cant believe you wouldnt help us after all the money this piece of junk cost us.

I purchased this piece of crap excuse for a washing machine, the Whirlpool Cabrio, almost 2 years ago, in September, 2015. Since that time I have had nothing but dissatisfaction about how it washes, and the extremely poor results. I contacted my sales associate early on, I was told, just like others who have purchased this machine, that it was a water-saving machine, and I needed to read the manual closely and just do what it said to do. I did that. Long story short, I am sick and tired of this machine, stopped using it, bought another machine that lets me choose how much water for each and every cycle, it washes extremely well, my clothes come out clean, it HAS AN AGITATOR, DIFFERENT BRAND, and I am very HAPPY with it! I will never ever buy a Whirlpool product again. I am well-known, have an extremely large number of friends, and I will be spreading the word that Whirlpool built a piece of crap. Never mind that piece of crap washing machine was mandated per government regulations to cut down on water, thats a bunch of crap. Users should not have to buy expensive cleaners, tote extra water to a washing machine that uses so little water that it barely covers the clothes, and no person should have to use a product like this. Never. Washed clothes from this machine stink, the odors will not leave my clothes, whites are now yellow, stained, and colors have white spots on them. Whirlpool, you have built this piece of crap, I hope you have large heapings of Karma! What a joke. What a useless company now, sell out and go play on the beach. You deserve the dirt, not your use-to-be-loyal customers.

Water pools at bottom of freezer and onto floor. Has been repaired twice, but still leaks.

Whirlpool Cabrio washer w103386894 - I have had nothing but problems with this piece of crap washing machine. Either the clothes come out soaked at the end of the spin cycle, or it gets stuck in a cycle and repeats. It makes so much noise you can hear it through the whole house. It is less than three years old and now it is leaking water. I had a base model Sears Kenmore that I had for over 12 years and it died from old age. This Whirlpool is pure crap, do not buy.

Purchased this dishwasher in 2015. It has been horrible. The unit has never cleaned sufficiently on any cycle. I run the unit in the evening for the full cycle with heat. It takes almost 4 hours. The dishes are still soaking wet the next morning. We would be considered light use as a family of two. I hand wash any larger pans or cookware as the racks do not support anything of midrange weight or above.With the poor cleaning, I purchased a additional silverware rack and placed it more centrally to attempt better cleaning. It remains mediocre at best. The most recent irritation is the door latch has started pulling free from the unit and remains attached to the door! I have to take pliers and remove it from the door and reaffix it into the housing of the unit. Will never recommend this nor will I ever purchase anything from this company in the future. Sad to see the quality falter to the point of absolute failure.