Do not under any circumstance end up with the Whirlpool fabric washer and or dryer in your dwelling to wash and dry your clothes. The washer, model # WTW7000DW0 and dryer, model # WED7000DW0. I am so upset with these units and the company I bought a 5 year extended warranty thru. I cannot put down in words what I think, because this review would not be published. Do not even accept these units, even if they are free. Even the repairmen who have been here said they would not buy these Whirlpool junk washer and or dryer series. They acknowledged the problem and said nothing could be done even though there is a legitimate problem. Not only is there a problem with the washer, the dryer as well has serious issues. All washes have to be put on the deep water cycle and some loads have totally dry spots on clothes where the clothes did not even get wet after the washer went thru the complete cycle. Also, get this, this washing machine even has to be cleaned itself with a cleaning tablet run thru a cleaning cycle. What happens are the clothes get a nasty, slimy, white muck on them. Even, immediately after the washer gets cleaned, sometimes the clothes 32nd up with this muck on them again. If you do not see this muck on your clothes before putting in the junk dryer, then the clothes have to be washed and dried again. This washer is supposed to be efficient, not a chance. It gets costly having to purchase the cleaning tablets and the washer(28th only two people in the household) has to be cleaned a lot more than what the manufacturer says and I called and asked. Pure junk, do yourself and even your enemies a favor, stay away at any cost, and like I said, even if they are free.

Microwave has melted a hole on the inside rectangular plastic cover. Model number is on recall list but not serial number. Opened microwave to find melted plastic on my popcorn bag that was dripping from the plastic up top. I will replace microwave but not with a Whirlpool again.

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

Purchased a Whirlpool dishwasher less than 3 years ago. Absolutely horrible! The LEDs stopped working on the control panel within the second year. A few months after that the heating element stopped working. Replacing the element and thermostat did not help. The warranty only last for a year, and now I know why. Whirlpool does not stand behind their products and they were completely unwilling to help, and were quite rude honestly. I will never buy a Whirlpool product again!

March 18, 2018. I was called today to inform me that the right front burner on my new stove Model # WEG745H0FS0 (ordered in early September and not delivered until mid-October from Menards) was not operating properly. The flame was noisy and yellow. I inspected it and found that the front burner base was substantially damaged by heat. See photo (Whirlpool stove part damage1). On inspection of the other front burner base, I discovered early signs of the same problem. (Note changes on burner base on the left of the photo.)In this photo (Whirlpool stove part damage2.JPG), you can see the damage to the burner base and also see some changes on the 3 to 5 O’clock position on the burner base on the left of the photo. This stove is less than 6 months old. The fact that the burner parts can be melted indicate poor design and danger to the owner/operator of the stove. Further, the operators manual for the stove I bought does not include any information on the model I have. It has pictures of the range top similar to mine but the model number is completely different. In addition to this, the Aqua-Lift Technology for cleaning the oven is completely ineffective. This is noted in several other reviews of this equipment. The problem noted by the other review became obvious the very first day I tried to use this range. A 2 cup pot spilled all over the cooktop as soon as I put it on the grate.

We have Whirlpool dishwasher for almost 10 year, very happy with the performance. This dishwasher is very quiet and also very spacious. The look and the price compared to other model is compatible and I will recommend it to other household. Thanks.

GW399LXUS range is Dangerous. Sheet metal cuts your fingers. In over 6 months, Whirlpool has failed miserably in fixing the problem. Bad replacement parts. Incomplete parts shipments. A dozen service calls. The local independent service companies are the only ones who have acted professionally. Other than the poor people who answer the complaint lines, nobody at Whirlpool seems to care. The product is poorly made and the product support is not competent. The range may have the features that we wanted, but who needs all this headache?

Bought this washer and dryer on sale at HD. The washer hasnt worked from the beginning. The clothes dont get wet because its an HE. I have to add buckets of water to even get the clothes wet enough to wash. The clothes come out with a residue on them. We use liquid HE detergent. It appears Im having the same problem as the majority of posters here. I will NEVER buy another Whirlpool appliance. There should be a class action suit to get Whirlpool to respond.

I purchased this stove in September and I am very unhappy with the Aqualift. The service department said I would have to probably do the cleaning process about 7-8 times for it to really work. I find that very unacceptable would never recommend this to anyone.

Bought in 2009 brand new set washer and dryer together at Best Buy. The washing machine in 2011 started its never ending problems. I’ve paid for parts & labor for the door lock sensor mechanism multiple times where I learned to repair that myself even buying parts and installing on my own last time... Then a drain pump went bad. Replaced that. Now a code f51 sensor to a motor rotor not spinning issue. Horrible. All the money and time in this unreliable machine is so awful. This thing also isn’t that great when it works too. Goes unlevel way too much having to redistribute and restart cycles all the time... Wish it washed better for the price and all the trouble. It is the worst machine. Has to be! Everyone I know can’t believe the fight I’ve had through the years with this machine. The company doesnt help you. Costly headache Junk machine!

My Whirlpool gas hot water heater will not stay lit. The thermal coupling has been replaced by my plumber. It did not help. This tank is defective. The product details are as follows: model # FG1F4949S3NOV, product # B07330262, and serial # **.

I purchased a Whirlpool washer 7 months ago, and a month ago, it broke. I have been without my washer for 1 month, and it has been repaired 4 times in that month. It is still not working. All I get is that, its under warranty, and there isnt anything they can do, but to keep trying to fix it. I have been having to take my clothes to a laundromat, and pay to have them washed. I have asked for them to deem it defective, but they refuse.

Purchased this Dishwasher on Feb. 28, 2015. In June 2016 about a 2 by 3 inch section of the enamel face on the door rusted and fell off above the air vent. After three hours of hold time between Lowes (with the extended warranty) and Whirlpool (their warranty department) it was determined that this was not covered by either warranty as it was beyond the date of the 1-year mfg warranty and was not covered by the extended warranty (it was only a cosmetic issue). As these calls took place over a matter of 2 days, it was interesting that between day 1 and day 2, Whirlpool had issued a statement that no rust repairs would be covered under any warranty repair - regardless, unless it affects the functionality of the dishwasher. In other words, they KNOW this is an issue with this model and are doing nothing to fix the problem. I must say that the folks at Lowes were most helpful; cannot say the same for the folks at Whirlpool. I do not think I will trust their products again.

I am so unhappy with my Whirlpool Cabrio washer and dryer. The clothes get so tangled and twisted that it stretches my sweaters totally out of shape. There is not enough water on any of the cycles that really clean your clothes. I saved my money so I could get something energy efficient and look great in my new laundry room. I would never recommend this product. Your sheets will not come clean because they ball up in the middle of the washer and come out partly dry. I have had this set for 3 years and now the bearing is gone; it leaks from the bottom and throws grease all over my new floor. I have battled the horrible odor since the second month. It smells so bad that I make sure I dont wash the day I have guest over. I am so disappointed and mad at myself for not reading any reviews before I spent my hard earned money. So here I am now 3 years into my ownership and having to spend more money on a defective product. The sad part is that I really thought I was getting something nice that would last me and my husband for years. There are only two of us in our household. This machine does not work properly; now it is broken, but hey it really looks good.

Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both ice makers went out, The computer on the filtration will go off. Refrigerator had problems maintaining temperature since 8.12.17. The refrigerator no longer works. This is my second unit since 11.09.16. It came from nfm.com.

Within a few months after I purchased my gas hotwater heater, I started having problems with it not wanting to stay lit. It was purchased in 2004. I see that this is an ongoing thing with Whirlpool. Every time I would call them, they would give me stupid answers on what it could be. One lady got hateful with me. I have replaced every part several times and Im having problems. About every two to three months, Im replacing thermal couple. As of right now, Ive been without hot water for eight days. I called and he told me about a trip button that is in the little white thing that has wires going to the thermal couple. I push in on it and then tried to start my heater and it worked. They have never offered to replace it or even give me a discount on a new one. No one should be having so much trouble out of your hotwater tank. This is not normal. These are defective and should be recalled. This company is ripping the consumers off and we need to stick together on this and do something about it. Im afraid to buy another heater because I can see that the new ones are still junk. What do you do?

I purchased a brand new fridge in July of 2014 (model wrf990slam00) hoping refrigeration repairs were now behind me. They were not. The ice machine did not work from day one and they knew it was defective when I called so they had someone come out to replace it. Just over a year later it is not working again and my freezer will not freeze either. They tell me I am now out of warranty and any repairs going forward will be out of pocket. Congratulations Whirlpool. You make products that last a whole year. Do not buy Whirlpool. They could care less about you or the quality of their products.

We bought the Whirlpool Gold series side-by-side about 2 years ago with an ice maker in the door and with this design, the ice bucket is on the inside of the door, which we thought was a very clever design, taking up less freezer space. Well, to remove the ice bucket, we had to use a blow dryer because even though you press the button which is supposed to disengage the bucket from the door, it has always been frozen onto the base.Then we started having issues of water leaking from the ice maker. It turns out, that the lever that controls the chute was broken. We called a certified Whirlpool technician to come out to fix the ice maker dispenser lever. Well as it turns out, it cannot be fixed. It is a sealed in the door unit and to fix it, we have to replace the door, a repair estimate for door and labor is approximately $800. That is absurd.I contacted Whirlpool and was told that my refrigerator is out of warranty and that there is not an option to repair the dispenser. There is nothing we can do. I said that according to the repairman, we are not the first to report this problem. When I contacted Whirlpool I was told there is no recall for this item. We purchased the Whirlpool based on the reputation that it has had in the past and the good product we have in a Maytag (which is associated with Whirlpool) dishwasher. Well, never again are we going to purchase a Whirlpool or any of its subsidiaries products. I have read so many unhappy customers here that I cannot believe that Whirlpool continues to make such inferior products or designs.

Whirlpool sent out a repairman to fix my range. I had it for 3 years, and one day I was baking cookies in the lower range and boiling water for pasta on the top left burner. There was a very loud pop, a bright flash in the glass top where the back left burner is, then there was no power to the range or oven at all. No clock display, burners would not work, oven would not work, nothing. As if it were unplugged. Of course, my warranty was about to expire in approximately 6 days (go figure) so I called the customer service line for repair. After 2 hours of back and forth with 3 different people, I finally had a technician coming out 4 days later. He shows up, takes about 35 minutes to get the glass top off, then says to me that he needs to order a part for it. This will take a few days. Ugh. Fine. 3 days later, part comes in. Same guy comes back out, fixes it. Ok.Up and running fine for about a year and 2 months. Then... POP! It happens again. Same scenario, different menu. (I was cooking breakfast). Now, warranty has run out and I have a $1,300 piece of scrap metal sitting in my kitchen. Worthless. My old KitchenAid stove was great. Had that thing for 13 years. Never a problem outside of replacing a $68 heating element one time. I paid $450 for that range. Tossed it out for this bells and whistles newer stainless steel glass top range/double oven. Regretting that tremendously. Whirlpool will be on my do-not-buy list for any appliance from now on. Didn’t even last 5 years. Oh did I mention the service call cost me $85? Yeah... Garbage!

I bought a new Whirlpool electric range in the spring of 2008 and purchased the extended warranty from Leons. The oven worked fine for the first three & 1/2 years, but then the bottom element in the oven seemed to have stopped working. The top element would still come on, in an effort to keep the oven at temperature, but was not effective.I called in a repair. The technician showed up, turned the oven on, noted that the bottom element did not come on properly & replaced the motherboard in the control panel with no further diagnosis. The oven worked for approximately 9 months and then the problem recurred. I called in another warranty repair. This time when the technician showed up, he turned the oven on & told me he was going to order a new bottom element, which he installed about a week later, again, with no further diagnosis.Now, here we are again, one month off warranty and 6 mos since the last repair, and again, the bottom element in the oven is not working correctly. I reported the issue & my dissatisfaction to Whirlpool and was basically told, How sad, too bad - hardware components fail and theres nothing we are going to do about it. Seriously? This range is just barely 5 years old and has a history of repeated problems with the bake function - obviously, something is defective in this product.I can see it, if I had not had any problems until this point, but when the same issue keeps coming up & obviously has not been correctly diagnosed and repaired, I would think they would have enough integrity to offer some kind of help or solution. Given the history here, its highly unlikely that Im going to be willing to spend big bucks on another attempted repair that, in all likelihood, will be merely a short term band-aid, so Ill probably have to buy another new range - which I cant really afford right now. Trust me, it will not be a Whirlpool & it will not be from Leons.

I replaced our old 50-gal water heater (10 years old) with a new top-of-the-line Whirlpool 50-gal water heater in Feb 2011. The Friday before Memorial Day, the heater went out and the pilot refused to stay lit. I called and jumped through all their hoops and finally figured out that it was the gas valve, because the pilot goes out as soon as you release the button and the milli-voltage reading is ok. They sent me a replacement and it cost $145 to have a plumber come out and install it. We were without hot water for 5 days. Now 9 days later, the pilot keeps going out. This time I can re-light it, but after the water heats up, it is apparently going out again. They refuse to replace a 12-year warrantied water heater that is only 2 years old and I am going to have to hire a plumber again to come out and attest to what we already know. This water heater is extremely loud. When we had it installed, I read the reviews and there were similar complaints (sounds like a mini jet engine). We dont seem to get as much hot water as we did with our old builders grade heater. This is a bad buy and I would advise anyone looking to purchase to look elsewhere.

After 6 years, Our $2500 Whirlpool refrigerator stopped cooling and would not dispense ice. Since we had purchased a Whirlpool extended warranty, a Whirlpool authorized technician replaced the compressor and informed Whirlpool it also required a new door that included an ice dispenser. A door was not available so Whirlpool refused additional repair and refunded the $400 purchase price of the warranty. Meanwhile the refrigerator stopped cooling again and Whirlpool refused any additional obligation. The refrigerator was now non-functional and we had to spend $3500 to get a comparable refrigerator. The moral: 1) Whirlpool makes very expensive refrigerators that have about 30% of the life-span compared to earlier vintage refrigerators. 2) They know this and will promptly refuse to warrant their product if it is to their benefit. Shame on you Whirlpool for using your corporate leverage and shady business practices to manipulate your customers.

I am experiencing problems with keeping my pilot lit too. I checked the screen and this is not the issue. I have just returned from Lowes where I purchased the water heater and they informed me Whirlpool supplied kits for this issue and it was widespread. They mentioned a class action and went on to tell me they and all surrounding Lowes stores are out of the free kit and arent expecting anymore. Am I to feel lucky my water heater water didnt fail sooner only to feel unlucky all of the free repair kits are now gone? Lowes provided me with the Whirlpool phone number for help and they have just informed me it will cost me $35.44 plus shipping. I now see how widespread this problem is. This isnt right. I am very disappointed in the handling of this known problem! What is my next course of action?

Owned it for approximately 15 years and has never had any problems with it all. I would highly recommend this product because it is affordable and easy to care for. It even comes with a filter for water. Great refrigerator.

DO NOT BUY THIS DISHWASHER (Whirlpool Gold Series dishwasher)!!! We bought a camp with this dishwasher in it brand new. It has been serviced three times in the past year because the dishes (especially utensils) do not dry. The service company first said it was because I needed to use jet dry. What a joke! I told them I was using jet dry so they sent a service man out. He had to read a manual in order to try and figure out what was wrong with it. He then decided the entire motherboard needed replacing and he would order the part. He came back, replaced the part and it still did not fix the problem.I called again to complain so they sent another service man out and he said the drying air vent may not be working. They came back out to replace it weeks later because the part was on back order. Wonder Why??? I still have to dry the utensils every time I run the dishwasher. The interior walls of the dishwasher are wet even after running through the drying cycle. Either this dishwasher is a lemon or Whirlpool is selling a dishwasher that does not dry to the consumers!!! So BEWARE!!!

Clothes dont always come out clean. If there is anything more than 2 sheets in the washer, it becomes unbalanced and then goes through a rinse until the water is up to the top! You have to watch any heavy load for this! Today there were 3 sheets in the washer and sure enough it kept rinsing until I physically reached in and rearranged the sheets. Then when it was done and I pulled the sheets out to put in the dryer, they were SOAKING wet! I hate this machine and will NEVER get an HE washer again.

I purchased a Whirlpool washing machine (new) in 2004. From the beginning, I had problems with the spin cycle. I phoned Whirlpool. I paid for service with no reimbursement. With the costs I have had for service, I could have purchased 2 machines. I have had to go to Laundromat to do wash then come home to dry. I have for 30 years only purchased Whirlpool large appliance. My washer and dryer were always refurbished but they were Whirlpool. I have had a (refurbished) Whirlpool dryer since 1997 with one (1) service call. However, this wash machine, purchased new, has been a money pit and a piece of trash with Whirlpool only giving lip service when calling. Also, going to the Laundromat, I have been amazed at how many individuals I speak with are there doing wash because their Whirlpool washer, mostly even newer models than mine, do not work! And they have the same story. There’s no service when you call. Shameful Whirlpool! Buy your parts from us. Maybe your credibility could be restored. But I will never purchase your Whirlpool or other names under Whirlpool! When I do get another washer, yours will be put on my front lawn with a large sign of your disgraceful products and service!

My wife and I bought a Whirlpool Cabrio washer and dryer set less than three years ago. And so far the dryer has been ok, but our washer has had to have a new motherboard and now it smells like its burning. Our last washer and dryer set was a hand down and was over 15 years old and never had any issues like our new ones do. Ill never buy another Whirlpool product again.

As a consumer, Im very disappointed in this Whirlpool Cabrio Platinum washer. It does NOT clean your clothes. Many times Im washing my clothes twice, only loading a 1/3 of a load of laundry in it because of this problem. No matter what you do, it just doesnt clean your clothes. Has anyone considered putting a law-suit against the company. They will NOT stand behind this issue, NOR replace your washer with something that works. Maybe that is what it will take. DO NOT ever ever ever ever ever ever buy this piece of crap washing machine. You will waste your money, your time, your extra detergent it takes to wash your clothes AND the cost of the machine too! The MILDEW SMELL is horrible and no matter what you do you CANT GET IT OUT! Ive tried it all. Im just angry because I had to save money to purchase this set and it is a piece of crap! The customer service is just a runaround, they wont help you! They will just give excuse after excuse. They need to replace EVERY ONE of our washers with something that works!!! For the cost of this machine alone, they should do something to resolve this issue!

Whirlpool Corp. stands behind its products. Bought the Cabrio Washer in June 2011. Lid cracked in October 2012 and was not covered under the Lowes extended warranty because they called it a wear item. However, our local Lowes store in Avondale, PA replaced it for us. In December 2013, the lid cracked again. I called Whirlpool customer service and they couldnt do anything. I called the Whirlpool corporate headquarters and was directed to a member of their executive staff. After explaining my situation, Whirlpool agreed to send me a new door free of charge and even pay to have it installed (which I told them I can do myself). Aside from the cracking of two doors, this washer is an exceptional unit. Its good to see Whirlpool stands behind its products this way, outside of the warranty period. I would guess that they always hear a lot of whining and complaining, but it seems if you explain things logically, people listen and are willing to help.

This microwave has crack everywhere and its barely 3 months old. When I want to use it, it makes this weird noise and then it stops. I have not talked to Whirlpool yet, but Ill see what theyll say. My recommendation right now for all those individuals trying to purchase a microwave, dont even look at Whirlpool brand, they just ***.

Whirlpool under-counter dishwasher (model DU1345XTVB0) was purchased 14 months ago. Upper rack plastic adjustable wheel rack is broken. Will not replace. Dishwasher has probable design flaw with wheel positions causing overhanging load to put extreme stress on outer two wheels. The design was done to save money instead of having telescoping rails as most dishwashers do. Explained this. They will not even send a part. Many other Whirlpool dishwashers use these parts. Probable class action suit material.

We bought a new Whirlpool Dishwasher. Installed it, wife used it for two loads. The third time she tried using it the door sprung and it no longer latches. After two weeks of calling Whirlpool, we finally had someone come out to fix it. After the repairman took a hammer to the frame he stated that it had been dropped. He wobbled the dishwasher back and forth with his hand. He said the frame will never be correctable and we will always have problems. After another week we got a hold of Whirlpool and were told the repairman has ordered parts to repair the dishwasher. Whirlpool is hoping it will hang together until the warranty expires. If the dishwasher were fixable that would be fine. However, when the repairman who has years of experience in his job tells me it will never be right and will always be a problem, I believe him.

I bought a Whirlpool Duet Front Load Washer in 2008 and it began showing F71 and F70 error code in 2011. I paid approximately $1,000 for the machine. The washer wont finish the cycles and often wont start. When I press the power button, I hear the 3 beeps and after a while, shows the F71 error over and over. The information I gathered online indicates that many people have the same problem. The repair cost is at least $550 to replace the user interface circuit board and is no guarantee. This is ridiculous.How could GE sell consumers this kind of junk that fails to work only after 2 years. I had a top loader for 12 years with no problems, not a single repair call. My wife and I are extremely frustrated with piles of dirty clothes and no washer to clean them. I want GE to refund the cost of the washer on a 10-year prorated basis. This is only fair.

Wish I had done more homework before I purchased a Cabrio washer and dryer. The washer uses so little water that I sometimes find dry spots on clothing when I take it out. How can it possibly be clean if it doesnt even get entirely wet? I now pre-rinse all of my underwear before putting it in the machine. I know the instructions say not to put in wet clothing, but if it breaks sooner, Ill get to replace it sooner with a more traditional model. I always use the lowest spin speed - anything else makes my clothes hopelessly wrinkled. I like the large tub for washing blankets and comforters. Thats about the only advantage I can think of. The dryer sensor quite often goes off after about 2 minutes if I use any setting other than the delicate or timed features. Ive had the machines for 2 years and had the dryer repaired once under the extended warranty I purchased. Very disappointing purchase.

Whirlpool Cabrio Washer WTW5000DW - I have owned at least two other washers in my life, and I just recently bought a new washer/dryer set at HHgregg. Was told they are doing away with agitator washing machines in the very near future so this is my first experience with a top load agitator-less washer. This thing is AWFUL!! First of all it took a minute to get used to the weird popping, grinding noises it makes while going through the cycle (which I might add seems to take FOREVER). The other thing I hate about it is there is no way to add the fabric softener at the start of the wash in this model unless you have a downy ball of which I have yet to find at my local dollar store or even the KROGER??? So I run back and forth trying to catch the rinse cycle to STOP the machine (wait I might add) and then add the FS manually.BUT THE ABSOLUTE WORSE THING is - my clothes come out with SPOTS that look like lint all over them, and they wont wipe off unless you have a wet rag to do it with!! AND YES - I have cleaned this washer TWICE already since January with the very expensive AFFRESH. I wear scrubs and they are solid colors, so it really shows up and I have to wipe off every pair EVERY day before I put them on then roll a lint brush down them. WHO HAS TIME FOR THIS??? This is on my SOLID colors which is easy to see, I can only imagine the GUNK that is on the rest of my laundry!!! I dont feel like my laundry is getting clean at all!! I am divorced and money is tight - I paid around $500 buck for this piece of crap. I am already seriously thinking of getting me another one - the OLD tried and true kind with an AGITATOR! And yes I am ANGRY. Can you tell??

I have to wiggle everything just to get thru a cycle on my brand new dishwasher! It fills up and works great when it does work. No prob! But it takes a good 30 minutes to get it work and I walk away come back NO WATER! Sometimes I have to unload it just to wash them myself! Now Im going back to purchase place and return or have repaired. Less than year old, repair free?

There is almost NOTHING I like about my new $1000 Whirlpool Cabrio Platinum washing machine! The clothes dont get clean. Stains become PERMANENT because clothes are spun and matted so tightly together, the 2 inches of water allowed into the tub cant dissolve them. Fabric softener stays a gummy substance because it has to be SUCKED out of the dispenser, not sprinkled out with water. I pin socks together to keep them in pairs, but this machine rips them apart and the safety pin end up in the bottom. My bathroom rugs are shredded. You cant add an extra item if you need to, because the tiny portion of water leaks out. There were DRY spots still on the sheets at the end of a cycle. This machine is an engineering nightmare, sort of like the Edsel. The only action programmed to clean the clothes is a wiggling motion on the floor of the tub. The tub spins so much, energy goes through the roof. Man was given 3 survival elements to assure our existence on earth: water, air, and food. Why are engineers trying to faze out our use of water? This machine has dazzling looks, but NOTHING else. I am so sorry I didnt read all the reviews first. Who would ever think the environmentalists would inflict such pain on our basic domestic obligations! If I dont get my money back or a decent exchange at Sears where we bought it, Im taking the machine to their parking lot and commencing a show with a baseball bat.

I purchased a high dollar built in side by side fridge with custom panels in 4/2005 and had my first service call in 5/2005. Since 2005 we have had 11 service call mostly for defrost failures and over temp. readings. From 2011-11/20/2013 we were issue free then the fridge over temp alarm sounded and we could not hear the fan motor. We had the certified tech come out to evaluate and found that the main control board needed to be replaced. Kitchen Aid/Whirlpool no longer make this item and forwarded us to Core Centric solutions to have a new one built. After speaking with the certified tech who had been out to service our fridge 11 times he informed us that these boards in his experience have never lasted more than a year. We spoke with a customer service rep a Kitchen Aid and asked about a prorated discount on a new built in fridge and she said it seemed reasonable but after checking for authorization informed me I needed to have the board rebuilt at my own cost and that even though this typically takes about 4 weeks to build the fact that our family would be without a fridge is not Kitchen Aids problem. 6/20/2005-over temp/not cooling call (replaced defrost thermostat) 9/2005-over temp/freezer iced over in bottom (freezer decided and drain unclogged) 10/05-over temp/not cooling (replaced fan motor) 9/06-over temp/freezer iced over in bottom (drain line decided, kitchen aid had no advice on how to fix) 10/06-over temp/not cooling, ice build up (whirlpool recommended replace heat kit and bimetal) 11/7-over temp and ice buildup in freezer with leakage (adj to drain pump and defrost drain basin made) 11/07- over temp and freezer icing over (whirlpool sent out a new heater probe) 6/08-over temp and ice buildup (bimetal and foam block replaced) 10/09-over temp, lights and motor shutting on and off (replaced defective board) 10/09- fan making excessive noise (ice buildup found on evaporator fan)11/13-over temp ice buildup in freezer, burning smell from fridge and no air movement or cooling in either compartment (need board rebuilt as on 10/09)Board no longer available from whirlpool, must be custom built at owners expense and will take up to 4 weeks. D/t continuing issues and whirlpool not willing to help the customer with replacement I would highly suggest no one buy a Kitchen Aid fridge.

After purchasing three gold series kitchen appliances in 2013 two months after purchase refrigerator failed. Whirlpool did not have a fix at the time. Told me I had to wait two months for a part to be engineered and then service to be scheduled which is not acceptable. They would not take back the refrigerator and give me a different model so I had to press Lowes to accept it back and they did give me a refund. I then had to purchase a different brand refrigerator which now I dont have a matching set in my kitchen.Then the dishwasher became part of class action lawsuit and now my gold series gas range is obviously damaged too. The control had the plastic panel is bubbling and it is split. Again after talking with Whirlpool customer service they refused to help with this at all claiming this is a cosmetic issue and it wouldve only been covered for 30 days from date of purchase. This gas range also has an aqua lift self-cleaning feature which does absolutely nothing. It does not clean the stove. You have to go into it and clean it the old-fashioned way with chemicals, gloves, mask and a scrub brush. These products are absolute junk and the customer support is non-existent. Do not buy Whirlpool products.

Purchased a Whirlpool french door refrigerator at Lowes less than two years ago. Last week the freezer compartment failed, out of the one-year warranty of course. The independent tech who came to service the machine told me of all the refrigerators he services Whirlpools are the closest to total junk and he would never recommend them. Wish I knew him before I bought this soon to be piece of trash. The CEO of Whirlpool, Jeff Fettig, received total compensation valued at $14.4 million in 2010, up about 15% from a year earlier, the appliance maker reported in a securities filing recently. Appears to me that Mr. Fettig is ripping off customers for his own gain, with his boards approval. Shame on all of them -- another example corporate rip offs that are plaguing our nation.

Whirlpool duet - I have had this machine for 4 years and have gone through as many door gaskets. They rip in no time causing damage to clothing and with the leaking damaging my wood floors. A definite do not buy!!!

WTW8000BW0 washer - This is the worst washer I have ever brought. We bought a pair washer and dryer. The washer started making noise when it was in spin cycle so we called repairman. He came and said it would be better if got rid of it and bought something else. Said it would cost too much to fix and hes seen too many of these. The noise is so loud we close door on laundry room and we cant hear TV in front room. This is the worse junk we have ever brought. Whirlpool should be accountable for this.

We purchased Whirlpool Cabrio Washer WTW5600 series in October of 2010. I bought the machine from Sears and also bought the extended warranty. Less than 6 months after I had been using it, I noticed that all my husband’s shirts were getting sweat stains under the arms and my hand towels were very smelly after drying with them one time. I called Sears to have someone come out and tell us what the problem was. He said I was using too much detergent so I reduced the amount of what I was using. It did not help the problem so I started using the extra rinse each time I washed, still did not fix the problem. I called them out 3 more times in 2011. One tech told me I was still using too much detergent so I reduced down to 1 tablespoon like he suggested. I stopped using softener in my washer because he said I needed to clean my machine more than one time a month, to clean it every 3 weeks. No solution to the problem still. I have had a tech from Sears and one from Whirlpool (who incidentally was the same man, he was from A&E Appliances). When he came in the door, my husband told him he had been here before and I said 2 times. He lied and said he had not been out before. Are we blind? No. He ran the cycle but sat in his truck while he was running it. None of the techs have ever put a tool on the machine to check if the water level is right. They just stand there and tell us to change the amount of detergent or clean the machine with Clorox more often. I cleaned it 8 days in a row and the clothes still smell and still do not get cleaned. We talked to main man at Whirlpool and said they couldnt do anything because their 1 year warranty had run out. We have been using Whirlpool appliances for over 30 years but I will not ever buy another one. I have probably had 5 Whirlpool washers over the years but never had a problem until we got this Cabrio top loader without an agitator. I would not recommend this washer to my worst enemy, if I had one.

My brand new top-loading, high efficiency washer has squealed like a banshee from day one. Whirlpool replaced the main agitator part, with no success. It still squeals so loud, you cant have a conversation in the same room. Now, Whirlpool says that it is normal. No, it is not normal for a washer to squeal so loud. I am still waiting on Whirlpool to replace the same part they replaced the last time. We are still not abe to hear each other over the squeal of our new Whirlpool washer. This is not normal.

Purchased a Whirlpool washer and dryer (WFW75HEFW0) in September 2017. Have had 4 service calls on washer for not completely washing clothes, leaving excess water after cycles complete, excessive wrinkling of clothes even on non wrinkle clothes, odor on some clothes due to incomplete water fill on some cycles. Factory position since there are no error codes washer is fine. Asked factory to exchange washer and upgrade model which we would pay difference. Denied. Looking for another brand and will seek legal assistance in the matter.

I highly recommend a Whirlpool dishwasher. Ours is a simple model. Cleans well and is quiet. It is 7 years old and I am glad we chose this model. Very happy with Whirlpool. All of our appliances are Whirlpool.

My Whirlpool dishwasher is only 2.5 years old. The first 1.5 years we were not full time in the house, so the dishwasher has not been used much. The touch pad went bad already and it was $450 to fix. Whirlpool sent me an email after I vented and it was a cookie cutter reply. They dont care that the appliance was manufactured with a faulty pad. We never buy service agreements because we feel an expensive item like this should last the term of service agreement if made correctly. No more Whirlpool purchases for us!

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

I bought a Whirlpool/Fridge Freezer Model WRF560SMYM 01, less that two years ago. Two months ago it started making a terrible noise. Apparently the freezer was iced up and a mechanic defrosted it. It happened twice more and he left saying he could not fix it. Another arrived and took the model number and he disappeared. A third the same. Now I have an empty freezer, just an ice maker. It seems to not freeze up so quickly with the moisture control on. Over $2,000 down the drain unless somebody can fix it. Oh and the fridge gets very cold! Does anyone have any ideas apart from throwing it out and buying another? Never another Whirlpool!

I purchased the washer and dryer set. My complaint is with the washing machine top loader that does not have the tall agitator not getting the clothing clean. All of my clothing come out of the dryer with dirty spots on them where they did not come out in the wash. Its a waste of water and energy because I have to wash them twice! I purchased the combo model numbers WED7300DWO and WTW7300DW0.

After much frustration and disappointment, as well as 2 huge repair bills with my front loading washing machine I sent it off to the scrap yard, still looking brand new, and went back to a top loading machine. I purchased a Whirlpool top loading, high efficiency, low water machine. I have had it for almost 2 years now and am extremely happy with it. I would highly recommend it. Fairly quiet and easy to use and takes very little detergent. It does not have an agitator so it is gentle on clothes. I know some users have complained about tangled clothes but, in my opinion, if it is loaded correctly this should not be a problem.

I bought a WDT 720PADW2 dishwasher 15 months ago from Home Depot. In the last few months, it has begun to rust at the vent above the the handle. Whirlpool will not address the issue because it is out of the 12 month warranty period, yet is obviously a design flaw.

I have the model FG1H5040T3NOV water heater and had found this message board. I called the number posted by Chris with American Water Heater and provided them with my serial number. They shipped me the replacement assembly next day and after about an hour, I had it installed and working again. Im not too happy with the fact that it failed, but it does appear they have their act together in getting the replacement parts distributed.Based on the discussion with the person on the phone, my only real gripe is this: the cause of the component failure was potentially caused by a dirty-flame trap that supposedly needs to be cleaned regularly. Since the trap is underneath the water heater and is in no way really accessible, relying on people to see the fine print in the manual (which hardly anyone reads) isnt sufficient. At an absolute minimum, a very clear and apparent sticker should be included on all water heaters indicating this needs to be cleaned and a clear description of how to clean it properly to prevent this sort of unnecessary headache in the future.

I bought a new computerized Whirlpool Cabrio top-loading washer and matching dryer 3 years ago. Bearings wore out under warranty, it was repaired. Just outside warranty, washer has broken down twice more. I contacted Whirlpool and received a high level of indifference to my concerns that they manufacture junk, and are not willing to stand behind it. Clearly, this is a faulty issue with the machine and should be repaired then and now at their cost. Do not buy Whirlpool products people.

I bake a lot so my husband bought me a new gas range for our 54th anniversary. After the first few times I used the oven, I decided to clean it. I noticed then that there were some burnt grease spots and streaks between the oven glass door. After 2 years of use, it has gotten much worse so I decided to take the door apart to try to clean the glass in between the layers of glass but there are three instead of two. I cleaned the inside of the outer glass, but that didnt take care of the problem. Most of the stains are between the other two panes of glass. That, I cant get to. I feel that this is poor design and not sealed properly. I take good care of everything I own and I expected this range to last me the rest of my life but it is put together with cheap plastic parts that wont last long. It is the first new range that I ever owned and paid a lot more for it than any Ive had. I expected better.

I purchased this washer (Whirlpool Cabrio HE) 2 years ago against the advise of many people including my husband due to the cost, $850 for what is now no more than a large paper weight! It had never really done a good job at cleaning our clothes. About 6 months ago, it started not spinning enough to remove all the water from the load. I thought, no big deal, I will just use the extra spin cycle. It became the normal thing - wash, spin, extra spin. Well, then it became wash, spin, extra spin, extra spin. I noticed 3 months ago that it was not even agitating. It fills up, sounds like it is agitating and then drains. There was no movement from inside at all. All along I am getting from my husband. told you not to buy it! I gave in and called the repairman - $185 for a console, $26 for a sensor and $55 for a couple of drum clips and then the $35/hour for the repairs. I would rather spend a couple hundred dollars and buy a washer with an agitator that really works. I would never recommend this washer to anyone!

Without a doubt, the worst washing machine Ive ever owned. After 15 years, my trusty old Maytag finally quit, so we searched around and ended up purchasing the Whirlpool Cabrio Platinum 3 years ago. In that time, the hinge on the lid broke, and now it makes a deafening noise when spinning. We called a repairman and he said the bearings were bad and needed to be replaced... Total cost $275 plus $50 for fixing the lid. When we told the repairman that it was only 3 years old he couldnt believe it! We decided against fixing it because from the start it never got the clothes as clean as we were used to, and without the agitator post in the middle, which was a big selling point by the salesperson who sold it to us, the washer continually stops with an Uneven Load message. Large load, small load, it doesnt matter. You cant do a load of any size without the load becoming uneven. We are now searching for a new washer, and although I dont know what well buy, I can guarantee it wont be a Whirlpool.

Purchased Whirlpool clothes washer Cabrio Platinum about one year ago. Never sufficient water to clean items. Appears that there is no way to add additional water to ensure that items are cleaned. Many items come out dry and still soiled.

Had a part come off right after our purchase but was a easy fix to repair. The silverware basket also kept coming off until we looked at it and realized it was on wrong. This dishwasher is much quieter than our last one. It also shows fingerprints. We got this dishwasher in a group purchase during a sale at Lowe’s that included the refrigerator a stove, microwave and this dishwasher.

We bought our washer (Whirlpool Cabrio) from a rent to own company about 2 years ago, and finally got it paid off. About a week ago, the lid started sticking when it was done washing. I went to open it last night to start some laundry, and it BROKE. Now theres a piece stuck in the bottom part of the lock, and the washer wont start. Anyone else have this issue?

My washer is a top load, energy and water efficient model. I am amazed at how little water it uses and how well it cleans. I do have two issues, the capacity looks huge but it will not take a queen size and double sheet set in the same load. It unbalances and then cant seem to get going again. The other issue is that you cant pause the wash and adjust things, you have to cancel and start over.

Unfortunately where I live the walls are thin. And my neighbors have complained about how loud my washing machine is. I load it correctly and sometimes while it’s washing it rearranges the clothes and it becomes unbalanced and makes incredibly loud thumping sounds when this happens. I’d say 1 out of every 4-5 times. Also I have multiple towels and clothing that have been pulled. The threads of brand new towel sets ruined from the washer.

My microwave is a Whirlpool WMC10511AW purchased in Jan 2014 for $150. It is very light weight and moves around when opening and closing the door. I have to use something behind it on the counter top to keep from moving backward and causing problems getting things in and out. In the first year we had problems with the door latch, but after a while it stopped being a problem. I am used to the stability of Amana Radarange so these very lightweight microwaves seem really cheap to me. It works fine at this point but it seems that these really inexpensive countertop microwaves have to be replaced about every 2-3 years where an Amana which costs a lot more lasts for around 20 years and are very stable not moving around all the time.

I purchased a Whirlpool® 4.5 cu. ft. Front Load Washer with Load & Go Dispenser in 2017. By August of 2020 the washing machine was no longer working. The machine would continue to fill with water and not shut off. The machine would then give an error of E01 and F03 and drain all water within 5 minutes of the wash load starting. I had a certified Whirlpool technician come and diagnose the problem for $99. The technician said these error codes happen ALL THE TIME on Whirlpool washers. The technician tried to replace the water pressure switch with no success. He then spoke to a corporate office and was told we would have to replace the motherboard for over $500. The total cost for the diagnosis and repair was almost the exact price I paid for a new washer just 3 years earlier. I will NEVER purchase any Whirlpool appliance ever again.

I purchased Whirlpool only front load compact washer in June 2015 and lasted only a year before the door lock broke and getting F6 error that means mother board to be replaced. Whirlpool warranty department (AIG) did not bother to do a complete repair and offer buy out at a 75% of my purchase price. My five year warranty premium cost was not refunded. I do not recommend this model be purchased by anyone. Whirlpool washes its hands on the quality and reliability of its product in US and that is a shame! A service life the unit should be at least 9 years with affordable maintenance cost.

I have been noticing my husbands shirts as well as my clothes continue to get what are spots of bleach and I do not use bleach on anything other than whites. This has been going on for quite some time and I noticed this morning another outfit is RUINED because of bleach spots. I decided to look up on the internet if this is a problem with this machine - AND IT IS! I am so disappointed I could cry. The clothes I have are donated to me. All my clothes are hand-me-downs - and my Whirlpool washing machine is ruining all my clothes and my husbands.

I purchased both the Cabrio washer and dryer because my dryer stopped working, it was old, and I knew that soon the washer would too, and wanted to modernize my set -- it was my moms old set. I was thrilled to get it delivered and should have had the delivery man from Lowes take it right back, when he told me they had just come from picking up one from another lady who was thoroughly dissatisfied with hers.Well, it didnt take too many washings for me to understand why that lady was upset! I really wish I had done the same thing! EVERY load of dark clothes have to be wiped off to get off the disgusting wet lint thats all over the clothes! Thats been going on since DAY 1! In every load, the clothes do not get completely wet and I thought I had combated that issue by having a pitcher of water always available to pour onto the load, so the sensor will add more water... That doesnt work, I now see!!! I just noticed last night lots of wet lint was on my fabric shower curtain liner, and I was thoroughly upset! I just never feel as though anything I wash gets clean. I truly wish I had come across this site BEFORE I purchased my set, and I would never have done so. Is there ANYTHING that can be done for people who have purchased these horrible appliances?

I think the whirlpool washer is a very nice machine. I think it does a good job of cleaning but still has the tub odor problem that a lot of front load machines have. As far as reliability it has done pretty well but I did have to replace the tub bellow and it is only 5 years old. It also makes a lot of noise so it is not a quiet machine at all. The steam option on the washer is a nice feature but not sure how much it does to help clean stuff.

I am questioning my loyalty because the last two Whirlpool fridges have been repair prone, and have bad design issues for ice dispensing. The dispenser door doesn’t close reliably and lets the ice maker warm up and melts the ice. This supports my rating.

I bought a house with Whirlpool appliances and I bought the extended warranty for all the appliances, I started to have issues with the refrigerator almost 4 months ago and still waiting for results, do not buy whirlpool products, every time you call the warranty department be prepared to spend at least one hour waiting for a customer representative. Buy LG or GE instead. These are excellent brands that I have owned in the past.

I purchased this Refrigerator Model #wrb322dmb, bottom freezer, 21cu ft. last year on July 3, 2015. In September I noticed rust spots on the top door. I called Home Depot where I purchased and they directed me to Whirlpool. I did purchase an extended warranty with Home Depot. Whirlpool did replace the top door. Thought that took care of it. Today one year and two weeks out of warranty, I again notice rust on both doors. Called Whirlpool. They said too bad out of warranty, not considering I had a previous report of this very same issue. So since I am very unsatisfied with this result and the fact that an expensive product is rusting, I decided to share to try to prevent someone getting stuck. Stainless steel is not supposed to rust which leads me to believe that it is not Stainless steel, but a Stainless Steel finish and not a very good one. So I am stuck with a rusting $1200.00 refrigerator only after one year. I have always purchased Whirlpool, but no more. They lost a 40-year customer. I have always bought American made but no wonder people are not buying American made any longer. TO SUM IT UP WHIRLPOOL STAINLESS STEEL APPLIANCES RUST! DO NOT BUY!

I purchased a whirlpool under counter oven - my main reason for not buying something cheap was the safety of my family - I chose the AKZM656 eye level oven. The stove is about two years old, but we do not use it that much. Two days ago my wife set the timer and placed a dish in for cooking; she then went outside to water the garden. About twenty minutes later she returned as something was burning- the oven reached a temperature of 350 degrees and would have burnt the whole kitchen down if she did not spot it. Now surely the oven should be designed to switch off if sensors fail? I reported this to Hirsch (Ballito) but they say they have no one servicing the Richards Bay area. I am not sure if this stove should be fixed as it is obviously not safe and makes me wonder how Whirlpool get safety standards passed on these items. Surely you expect better when buying a well-known whirlpool brand?

I purchased my range, model #WEG730H0DW0 in April 2016. I am extremely dissatisfied with the product and the Whirlpool service. I guess its comforting to know that Im not alone. Ive had two problems so far. The first is with the broiler that clicks on and off. It took several visits and a new electrical board for the service person and me to figure out that the door has to be closed to broil. Not sure about all of you but I am used to keeping the door cracked open to be able to keep an eye on the food being broiled. Apparently there is a thermostat at the front of the oven designed to keep the electrical controls from getting overheated or from melting so when the door is cracked open the heat from the broiler hits that thermostat and the broiler is shut off.The people at Whirlpool are awful and rude. I made so many calls and described the problem in so many ways and not one person knew about this newly placed thermostat or thought to ask about keeping the door closed. It took me and my service tech over an hour of troubleshooting on his SECOND visit to figure it out. He looked up the specs and we figured it out. I wonder how many new electrical boards have been replaced when the solution is as simple as keeping the door closed. A stupid design. Also having the same problems with the knobs. They turn so easily that twice I have smelled gas and realized one of the knobs was turned ever so slightly (before the clicking sound to ignite the stove).Then the third time could have been deadly. I had friends come pick me up and we stood in the kitchen for a bit before we left for the entire day. When we returned the whole house smelled of gas. Someone inadvertently must have brushed up against the stove and the knob turned. My dog, thankfully is still alive and so are we. THIS IS NOT ONLY A STUPID DESIGN BUT A POTENTIALLY DEADLY ONE!! I am forwarding this message directly to Whirlpool in the hopes of getting my money back. I am replacing the range immediately and will never purchase a Whirlpool product again!

I purchased a new Whirlpool stainless steel smooth top range model #WEE745H0FS and it was installed the day before Thanksgiving, 11/22/17. The oven door handle was broken on inside by installers. I called Whirlpool warranty on 11/24/17 and requested a repair. A repairman came the following week two days late. He said he needed to order a part. After calling the “Whirlpool approved” repair shop multiple times over the next two weeks, I was told the part was backordered. Finally, yesterday, 12/13/17 the repairman showed up an hour later than appt. time. He took the oven door apart again and the new part didn’t fit my oven door. He had carelessly ordered the wrong part. I was told he’d put a rush on the correct part and that it would be here 12/18/17. I will never buy another appliance from Kelley Appliance in Augusta GA nor another Whirlpool product. I have had to use duct tape on my brand NEW oven just to use the oven so it doesn’t fall apart when opening.

I replaced our old Whirlpool washer that we had for 10 years with a new Whirlpool high-efficiency front load washer in August 2020 - it quit working on December 11, 2020. Got a repair person through Whirlpool on December 22nd who said I need a new motherboard. I am still waiting!!! 42 days with no washer and Whirlpool has no answers regarding the parts arrival and I can’t even sell the thing and get another brand because it doesn’t work! I’m beyond angry!!

Purchased a double wall oven and had it for 13 months. Used it this past Christmas and for the first time used the self cleaning mode. After an hour the power went out and now the oven is dead. Whirlpool service sent me to a local repair company and they want $70 to come out and look at the oven. This seems like a huge problem based on all of the feedback on the web. This is an obvious lemon and Im going to talk all over social media about the poor quality of this product.

I purchased this dishwasher washer (Model WDT710Paym3) in May 2013, quit cleaning. I have checked filter. I run this washer 1 or 2 times a week. Very disappointed in washer and the quality of the product. Dont think my next purchase will be a Whirlpool.

I like the dishwasher. It cleans pretty well. Some time it soap doesnt open and the dishes don’t get cleaned. But when it’s working good the dishes get cleaned very well.

On April 10, I bought a Whirlpool washing machine with a sensor. My clothes do not come clean. The dirty spots are still visible. I had three technicians come to check it out and after they just made the machine start, make the water run, and make the water empty, they confirmed that it was working normally. I have insisted on having someone come and just do a small wash and they did not agree because they are not there to wash clothes. I went back to Leon’s where I bought it and the saleslady told me that she could not do anything about it. I have been dealing with the customer service and the person has tried three times to get someone to come and check the washer properly and was insisting in front of me that I wasnt at all satisfied with the performance of the washer and still confirmed that the washer was working fine. They keep saying that there are no parts that need to be fixed or exchanged, so that means there is nothing wrong with the washer. I have tried all different kind of soaps. They were suggesting that I use Tide, which was the best performing soap. I used Tide or Purex - I even tried half a bottle of bleach - and it would not clean my clothes. The problem is the clothes are not turning, they just hardly moved with water that just keeps the clothes humid. I tried putting in more water with a bucket and when I push the start button, it would drain out all the water that it did not put itself. Ive called the consumer protection and they have advised me to take legal actions against the company and the store that sold it to me. They confirmed that whatever we buy, the article has to do the work it was made for; so the performance of a washing machine is to wash clothes. I even took a three-year prolonged warranty and the store told me that once the one-year warranty with the company has expired, then they could help me with sending their technicians and see what the problem was and they would take it from there. I have an account with the store and I have eighteen months to pay it off. So I was wondering if the saleslady did sell me an appliance saying that it was very good and that I should not have any problems with it. Can I take steps going against her for false advertisement? It’s a month now that my clothes are not washed properly and I need to rewash them by hand before putting them out to dry. The consumer protection office has been telling me that the store should be the one to finalize the problem with the company, but it seems that not even they can come to an agreement. Whatever steps I will take against the company and the store, what are my chances of getting my washer replaced? Whirlpool has been advised about me taking them to court and I got permission to do so. Actually, they invited me to go ahead and do what I thought was right. I do not have the money or time to waste on something that maybe I will have no chance to get anywhere. All I want is to have it replaced with another washer that would be more performing. If anyone has had the same problem and had their case solved, maybe it will give me hope to go on. Please, what is the best and fastest way for me to get this problem resolved? I do need a washing machine. I do need to wear clean clothes. Thank you for your patience and understanding.

The French door fridge with the freezer drawers on the bottom are very flexible and easy to access. It goes downhill from there. The ice maker takes 4 days to fill up the bin with no use. The unit does not defrost and freezes up every six weeks requiring a manual defrost. Three mods have been made under the service contract and performance has not improved. PC boards have been replaced and at least one thermistor. My understanding is this is a single compressor unit with piping, relays and valves to port refrigerant to two different evaporators as needed. Unfortunately it simply does not properly balance/defrost and the freezer door freezes up. It certainly is not compatible with a high humidity environment. We will never buy another cooling design like this, but sure like the French Door layout. Glad we have a service contract.

I have always liked Whirlpool products but it seems lately they are lagging in this department. My washer/dryer combo each separate I dont feel are doing the job they should be. Washer is the bigger problem. Softner dispenser not distributing the softner correctly and now I have to clean out after each use. These are about 10 years old now. Is not spinning all the water out and not at all sure if clothes are getting clean. Most of their products usually lasted much longer back a few years.

I bought my new ceramic top electric range/oven with convection, and the aqua-lift cleaning system in spring 2017. The aqualift cleaning function is a joke, so be prepared to be down on your hands and knees scrubbing. Im careful, and Ive not spilled anything yet, but the oven still gets splatters from roasting meats, etc. Id hate to see what Ill have to deal with when I actually let something spill. Today, as I was down on my hands and knees trying to clean it, I noticed that the enamel is chipping off where the oven racks slide in. Great. I have never had an oven where the enamel came off, much less within a year. I am struggling with heart failure, and I am not up to fighting with Whirlpool.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

We bought a Whirlpool dishwasher and microwave from a reputable appliance store. The dishwasher top basket broke within 30 days. The microwave lost 100% power within 30 days. Both under warranty but parts had to be ordered. Couldnt use either appliance for over a month. What is going on Whirlpool? We need a refrigerator, but I no longer trust your brand. I dont want it to quit and then lose all of our food! Please get it together and make quality products again.

This is the only time in my life when I have seen a Microwave behave so badly (and one that is relatively expensive). The microwave is defective out of the box. Seems like there is a comWhirlpool MWA269 (4You)mon trend with Whirlpool products and cheap Chinese boards. The microwave never stops working once the timer runs out. It will just keep going. Model is Whirlpool MWA269 (4You).

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

Purchased the new dishwasher in 2009 through the builder of our home. I quit working completely like there was no power to it. We replaced the fuse to it and then it worked, but kept pausing during the cycle. Sometimes it will completely go off and then when the control panel comes back on, it sits paused until you push the button. We replaced the computer with a new one and it works even worse. It shuts down more often and still requires a restart. So frustrating! Appliances should last longer than a couple of years.

Ill never buy Whirlpool appliances again. I purchased all new kitchen appliances less than 3 years ago. The range had electrical issues within the first year, which was extremely scary. Thankfully because of the warranty they took it back, reimbursed me for it and I replaced it with a GE. I absolutely love the GE. The dish in the microwave never stays on its track in the center. Its quite an inconvenience to fix it almost daily. The top rack in the dishwasher constantly breaks, drops down on one side. Random parts from inside the dishwasher constantly come loose and fall off. But the worst of all....my refrigerator has broken down twice in 6 months from the same issue due to no fault of my own. To give some credit, Whirlpool fixed it out of warranty the first time. However the same issue happened 6 months later and they are expecting me to pay for it. The repair company contracted with Whirlpool covers their parts under warranty, however different parts need to be ordered. I had to pay for these parts, a service call and labor. Whirlpool came out with a service pointer on this because they know its a manufacturing defect but are refusing to cover the cost. The representative I spoke to was nasty and inconsiderate but sadly the manager was even worse. DONT buy Whirlpool!!! I recommend GE, youll be much happier. Worst customer service and support.

I purchased the Cabrio washer and dryer and paid for the extended warranty from Lowes about 5 years ago. After about a year, the washer had problems with excessive vibration and noise. Under Lowes warranty, a repairman came and adjusted the level. He came out several more times and made other adjustments, replaced the drum, then bearings and raised the level again. He said he could not declare the washer a lemon, even though it was because they were told this was taboo. They were instructed to do whatever they could to keep the washer going throughout the life of the warranty. Now the washer stops mid-cycle and an fl or f1 error code appears on the control board. I contacted Customer Service who said I can purchase another extended warranty for over $300 or pay their repairman for the visit including parts and labor. What I paid for the extended warranty and to purchase a new one would pay for a new washer.

Worst refrigerator Ive ever bought. Previous one still perfect shape. 22 years old. Freezes everything on top shelf. Motor making grrrr noises. Had repaired. Now bottom crisper drawers so cheap the plastic is breaking. Drawers wont slide. Now Deli tray lid snapped in half! STAY AWAY from this USA made product.

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

On May 15, 2017, I purchased a new Whirlpool Water Heater, unknowingly made by American Water Heater Co., from Lowes (receipt attached). Model Number ES40R10-55 with a 10 year warranty. The water heater was installed using the directions in the owners manual. Upon turning on the current to the water heater after it was filled with water and all air removed from the plumbing, the module gave a code stating the top element was not working. Called the Technician Assistance Hotline and they gave me a RA number to get a new top element from Lowes. Got that on May 16 and had to call the plumber that is contracted by American Water Heater Co. to come to the house and inspect the heater to make sure it was installed correctly.The water heater worked once the new element was installed. On Oct. 3, 2017, had more issues with the module stating the top element was not working. Called the Tech. Assistance Hotline and they gave me another RA number to get another top element. On Oct. 4, got the top element and installed it. The water heater started working again. On Oct. 6, the module stated the bottom element was not working. Called the Tech. Assistant Hotline and had the plumber come out. He determined that he could not find out why it was doing this and also said that both elements were good along with the element that I removed on Oct. 4, which I still had. Since then, the module has been giving codes stating that both elements are bad and I have not had any hot water since Oct. 7. American Water Heater Co., Whirlpool, and Lowes all refuse to give me a refund for this piece of junk! All blame the other for the problems and none will take any responsibility for the water heater not working. I will never buy another appliance with the Whirlpool name and definitely will not buy anything made by American Water Heater Co. I also will never buy another appliance from Lowes as they are not willing to help me in this matter. If you do not want to experience the headache and frustration of owning a new appliance that does not work, I would suggest that you do the same!!!

I bought a Cabrio washer in 2009. I started receiving the infamous F51 code. When I called Whirlpool, they refused to even acknowledge that there is a problem with this washer. When I brought up the pages and pages of complaints about it, they acted like they did not exist. I hope this review will deter people from purchasing one of these faulty products!

This complaint refers to model number ET8MHKXMB. It was purchased in November of 2008 and the fan had to be replaced on May 29, 2012. The cost of this repair was $189.79. This is a terrible thing to have happened. Obviously, the fan was made cheaply. We are very dissatisfied and will not purchase another Whirlpool refrigerator ever!

We purchased our suite of appliances from Home Depot, this was a great experience. Unfortunately that is were it stopped. Our 1st refrigerator caught on fire in the electrical within the unit. We got a 2nd refrigerator sent to us and it came damaged. Then they sent us a 3rd refrigerator and it caught on fire in the electrical as well. Weve been dealing with this all since August 27th 2019 and here its now October 14th 2019. At this point I feel this model of Whirlpool is truly unsafe.

The washing machine has been through 4 boots. The boot material is so flimsy, that they tear constantly causing water to leak out of the machine. There are times it is minimum water, and other times a lot of water.

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

Own Whirlpool GB2FHDXWS04 refrigerator for 14 months. From the beginning, the ice maker made gross tasting ice and never got better (had to start buying ice). Then a smell started coming from the fridge every time the fan came on. We called before the warranty was up and talked to Whirlpool, and they said that we must have put something smelly in the fridge that caused the plastic to absorb the smell (which we didnt). They told us to put baking soda in and change it everyday. No change. They kept telling us there is no way it could be giving off a smell for any other reason and if they sent a tech out, we would have to pay for it. Trying to intimidate us until the warranty was up. Then after a month or so, the bottom mount freezer starts leaking water all over the wood floors every 3 days. At first we turned off the water line, but then realized it is coming when the freezer defrosts. One good thing, the freezer, from the beginning, knocked really loud and now that its leaking it doesnt knock. We spent $1,200 just over a year ago and will probably have to go purchase a new one now. I will tell you it will never be another Whirlpool product. Whirlpool has not apologized or done anything but say, Now your warranty is up, you should have bought the extended warranty. Great customer care! With all these same complaints, you would think Whirlpool would figure the problem is their inferior product (which they know) and actually take responsibility.

Purchased this simple 30 wide fridge July 2017 to fit a short kitchen slot. It worked adequately, but it only had 3 temp settings. The highest setting was too warm and coldest froze food in the fridge within days. The middle setting was a little cold but the best option. Food in the back did occasionally freeze and we had to be careful for vegetables in the drawer freezing. Often we wrapped lettuce and more fragile veggies in towels to absorb moisture and slow down freezing. Two years after buying - almost to the day - the fridge stopped cooling below 45F. The freezer still worked, so I thought it might be fixable. I tried some DIY repairs from a couple of websites but nothing worked. Within a week, the fridge temps were up to 50-55F. I gave up on buying ice and keeping food in coolers. I bought a GE and havent looked back.