Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

This morning another chunk of our Whirlpool Microwave handle fell off while I was cooking breakfast. I got on the internet after breakfast and typed in whirlpool microwaves to see if anyone else had experienced problems with their microwave handles and found this site. We purchased a Whirlpool Microwave oven from Lowes in 2011 (over the range model). About two weeks after it was installed, I noticed a crack in the handle. Then a few days after that, a small chunk of glass/plastic fell off of the handle when I shut the microwave door. Since that time, the door handle has been steadily disintegrating. Sometimes chunks of plastic fall off when one shuts the door, even if you are very gentle. Chunks of plastic fall off nearly every time I clean the microwave door, even if I dont touch the handle. Sometimes chunks fall off randomly when Im not even using the microwave. Pieces of plastic have fallen into my cooking pots a few times. Perhaps the steam from the cooking food loosens the cheap glue holding the handle on? What an inferior product! I am very dissatisfied with Whirlpool and will not recommend their products to anyone.

I bought my Whirlpool over the range microwave WMH32L19AS November 28, 2015. We started having problems with it, working intermittently one year later. I called Whirlpool in January 2017 and they told me it was out of warranty and it would cost $150.00 for a repair person to just look at it. I decided to just keep using the microwave because I only paid $232.00 for it and I figured after parts and labor if would probably cost over $200.00 to fix it. I called Whirlpool back in June because the microwave wouldnt shut off and even kept running when you opened the door. Whirlpool sent out a repair person at no cost to fix it. But the repair person told me Whirlpool only paid for him to diagnose the problem. I had to pay for the repair. After working on the microwave and replacing sensors and fuses he determined the microwave irreparable. I called Whirlpool back and they just told me that my microwave is 1 1/2 years old and they were not responsible after 1 year and I should have bought the extended warranty. I will never buy another Whirlpool appliance again.

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

My parents bought a Whirlpool washer machine and the machine was fine for the first two years, then water started leaking from the bottom of the machine and no one has yet to fix the problem! They have the worst customer service department. The A&E worker who came to my parents house smelled, wasted a bunch of time working on the machine and didnt fix anything! The A&E worker visited my parents house over 10 times and the problem still wasnt fixed! They (worker) have ordered parts after parts and still water keeps running from the bottom of the machine! Someone, please help and cut Whirlpool from the stores! Ive spent almost a whole on the phone trying to help out my elderly parents! Its ** and a lot of headache! Never use Whirlpool; theyre all crap!

Purchased front load washer & dryer 2009 - have had issues with the washer ever since. The last episode has taken 3 visits from repairman - they cant figure out what the problem is - wont finish a cycle (any of them) and locks up. Cant open the door without turning it off and then back on. But the load wont spin dry - leaves clothes wet. Already had the harness replaced a couple of years ago and now they replaced the flywheel (it was warped) thinking that was the problem. Nope. Still wont work & the repair company said they cant figure it out & neither can Whirlpool. Im very angry after reading all of these posts about Whirlpool. Not a happy customer. But what can you do???

We had the refrigerator delivered in March, 2013. We noticed a leak in February 2014, only because we smelled a musty smell in our garage, and removed the rug outside the door, from the garage to the kitchen. Then we started noticing water in the garage. It was shortly after we determined it was the refrigerator. We bought this at Lowes and they use A&E, and they did not show up for the first appt. They did replace the pan a few days later while we had to replace dry wall behind the fridge. This time around (month later) we noticed the fridge/freezer was not cooling. So A&E came out and determined its the compressor. So now we threw out hundreds of dollars of groceries, and water was leaking all over the floor again from ice thawing. I believe the refrigerator has had problems all along. We have had it for one year. I think we should be reimbursed for the compressor! Thats the least Whirlpool can do after losing so much food and money spent on the wall, and all the water mess etc. I will never buy Whirlpool again, and I will never purchase from Lowes again. We always bought at Lowes, but this was a bad experience, and I get told one thing on the phone with reps and another by A&E.

The washer has a convenient water level feature which enables conservation. The dryer also feature multiple heat/timing features, another conservation plus. Both are compact and easily loaded and unloaded. The multiple alerts at the ending of the dryer cycles are a convenience.

We had refrigerator 2 years and compressor went out. Whirlpool would not repair. I will not buy Whirlpool again.

Whirlpool Cabrio washing machine: The washer was purchased in March of 2012 and malfunctioned in December 2014. After phoning Whirlpool, the machine was scheduled for repair with a factory-authorized company. The first repair attempt was unsuccessful due to a lack of parts. It took 10 days for the parts to arrive, and another unsuccessful repair attempt was made. The verdict is that a new motor control board, costing $350 plus labor, is necessary. With the delay in service and cost of repairs, I may as well buy a new machine.

I will be brief. Bought Whirlpool ref. model #WRF560Smywo4 on April 15, 2016. The refrigerator quit work July 29, 2016. Called Whirlpool. They responded they had no repairman in our area. After several calls they scheduled a repairman. He came and put on a part. It did not work. Called Whirlpool again. They sent the same repairman. He stated it needed a new compressor. A week later he arrived with the part (August 12, 2016). As of now the refrigerator is working. Now this was two (2) weeks without a refrigerator. This has been a bad experience. I WILL NEVER BUY ANOTHER WHIRLPOOL APPLIANCE AND RECOMMEND THAT YOU DO NOT PURCHASE ONE.

Very unhappy with this fridge. The ice maker is finicky and the side shelves keep breaking. The cake drawer cover broke almost immediately. We replaced it and it broke again so we just took it off.

We replaced our kitchen appliances and went with Whirlpool. The oven and Refrigerator havent had any issues yet but the dishwasher has been crap since it was installed. While it looks 10 times better than my old dirty dishwasher it replaced, its main function of washing dishes is 1/4 the of the quality after running two or three times. Not to mention the average cycle time is 4-8 hrs. Dishwashers by design, should be convenient and save time. Whirlpool managed to remove both of those traits from this Dishwasher and now their warranty service said they can send out a technician but I will have to pay for it if it’s not covered under warranty!

First my pump went out on a 4 month old washer. Had to wait several days for them to fix it. My washer worked for two weeks and same problem. Its been over a week and the service man cancels then shows up and tells me pumps out and can get one for several weeks. I cant stand them still not fixed.

I have a Whirlpool Cabrio washer (Model: wtw6400sw2 / Serial Number: cu0271913) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool and I will contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

My Duet Sport washer drum is damaged due to the poor quality of the bearings. I replaced the Whirlpool Duet Front Loader Washer Bearing & Seal Kit W10253866, W10253856 but because the bearings were damaged the drum is also damaged. When I opened the rear panel of the washer the bearings had literally come apart and bearings fell out. All of the floor and the oil/grease was everywhere. I replaced the bearings but it didnt matter because the drum is warped. Priced the drum and it is nearly $400.00 to replace the assembly. The cost of the drum assembly is about half the cost of a new washer. I will never buy another Whirlpool product again. Just a shame that the cost of a replacement drum is so high. What caused the bearings to just explode and damage the drum. What did I do to cause this? Absolutely nothing. I have since discovered that this is has happened to scores of people with this same washer.

I hate my Whirlpool refrigerator: It has a upper freezer with no light. The shelves are not split and raising or lowering shelves gains nothing and may even take space away. I would never ever buy another Whirlpool.

This is Whirlpool model MVWP835DC2. I bought brand new. Recently used about once a week. Got an alarm that indicated no communication to core unit. Talked to Whirlpool service and unit is out of warranty (20 months) and advised I should use authorized service company to come and diagnose. This took 2 weeks. Service man came, washer did not power up. He quoted that repairs would be $750 and not worth it, buy a new one. I went on internet and found YouTube videos that showed how to diagnose and fix. I called Whirlpool for new console, $350 and one month. Went to parts house and got part for $250. This fixed problem.I have a few problems with this machine and company. 1) This now turns out to be a known problem with these machines. The console fails. I am not sure how this is going to last 30 years. 2) Service man took nothing apart and could not diagnose problem with no power. He quoted $350 for the console and the balance for the core. He was guessing or pulling a scam. Take your choice.3) Part not available from Whirlpool because so many are failing.Thanks for making a great product.

This refrigerator (French Door Refrigerator Model: WRF757SDEM) has been problematic since day one. The ice dispenser sends crushed ice all over the kitchen floor. The temperature in the upper 3/4 of the storage area and on the door is 57 degrees (it should be between 36 and 40 degrees). The item was purchased at Best Buy on October, 2016. It is still under warranty. I have had several visits by repair people and so far no fix. My friends call it a crockerator, since you can freeze food in the freezer and slowly cook food in the refrigerator section. I tried twice to get Whirlpool to pick up this thing, but so far no go. DO NOT EVER BUY A WHIRLPOOL REFRIGERATOR! They used to make good products, but no longer do.

I paid a lot of money for this because I thought it would be high quality and last for quite a while without problems. First of all, you HAVE to open the right door before the left door and then remember to ALWAYS close the left door first and then the right door. If you dont the doors dont close well and your refrigerator gets hot AND THERE IS NO BUZZER OR ALARM TO TELL YOU THE DOORS ARENT CLOSED. After 2 years the freezer repeatedly freezes up and then the refrigerator heats up. My repairman says the controls on this refrigerator are WAY odd and instead of just buying an inexpensive part (defrost timer for example for $50) he need to order the entire control for probably 3 time more. NOT WORTH THE MONEY OR TROUBLE. BUY ANYTHING OTHER THAN WHIRLPOOL GOLD.

I have not use wash machine for 46 years, however, since I the caregiver for my wife (with Parkinson), Im the user of our washing machine, High Efficiency Whirlpool for 8 months. It Is very easy to use including the dials. It is very efficient to use.

Whirlpool Calibri washing machine - I have the washer for 4 years and have replaced four computer boards to the tune of nearly $300 each. When Whirlpool was told of my experience, they said they were sorry. Obviously, I am too and will not buy again. You would think they would give me one board at no cost, but I guess words are cheap.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

In October 2009, I purchased a Whirlpool Energy smart gas water heater with flame lock safety system.$509.00 I had it installed on 5/4/2009 by Westmoreland Affordable Plumbing, $218.00. On 10/15 called Whirlpool stating that the upper thermistor was coding as a failure. They sent me another one to replace it on 10/19/2009. On 10/19/2009, 1 and 1/2 hours later, the tank was coding a bad gas valve, called back and told Whirlpool what had happened and that I smelled gas. I shut off the gas to the water heater and waited for a valve replacement to arrive. On 10/21/2009 I had E.H. Plumbing to install the new gas valve to the water heater, $150.00. On 10/28/2009 the new gas valve went bad. I contacted Whirlpool and argued with them until I had them replace the hot water tank. With their approval I went to Lowes and tried to get the same water tank but they no longer sold that model anymore. I was given their equivalent to the one I had purchased earlier. I had it installed on 10/29/2009, $150.00. I now see a class action suit was filed against Whirlpool for the model in 2008. They were still selling this model after the lawsuit???? I spent $1027.00 for a $509 hot water tank and a lot a days without any hot water. I have all my receipts and returned codes for this transaction. Is it possible to get my $300.00 back (for two extra installations) as a result of this problem? I also kept the old gas valve thermostat.

Purchased the fridge from hhregg in August/September 2012. Model G16FARXX. After less than three years of owning it, found out today that the compressor is shot and will have to be replaced. Replacement/repair costs are ~$900, almost as much as the fridge brand new. Chatted with customer support and then would/could not do anything. I feel ripped off. If it happened after 5 years of use, then my attitude would be different, but not a major component going out in less than 3 years.

I bought a washer dryer Cabrio set and the washer after 2 years has a bearing failure and is squealing badly. The service technician quoted $400.00 to fix a washer that cost me $800.00 new and is 2 years old. I had a Whirlpool washer and dryer set for 11 years with minimal issues and that is why I bought Whirlpool again. This will be the last time. It is a matter of time before the washer fails and I will have to purchase new or pay the service technician.

Never ever go for Whirlpool. It has the worst customer service. We brought an oven but accidentally we broke the inner oven plate. We called up the customer care person on 18002081800 and tried asking him the dimensions of the plate pr at least how we could reorder it. He never listened to us. He just got our details. Said that technician will come at 11am tomorrow and disconnected the call when we were trying to explain what our query is all about. Is that all the respect a customer deserves!? Is that how whirlpool trains their service people!? He doesnt even have the basic courtesy to listen to the customer, I wonder how was he even recruited as a customer care person. If you want at least your basic respect, please DONT BUY WHIRLPOOL.

Purchased this washer 5 months ago. Have had service 3 times as dark clothes come out with white residue. I have done everything possible to correct the problem. They recommended from cleaning the machine, using less detergent, minimizing the load, using extra rinse, deep water and still the clothes come out with the residue. And it takes way too long to wash a batch of clothes. This is a known problem with this model. Repair company recommended a replacement and Whirlpool insists that it is a usage problem. One thing they said Could be water is too cold, I live in Florida there is no cold water! Whirlpool refuses to replace it. DONT BUY IT!!!

Their water heater is the worst ever! I will never buy another Whirlpool product. We purchased our water heater on January 17, 2010. We had to have the entire electronic system replaced in August 2011, including the lower element, control unit, thermisol, and electronic. Now, just a few short months later, the system is not working again, plus, the containment unit failed, flooding our basement. When we called Whirlpool, we were treated callously and rudely. Now, we have to pay to have the old unit removed, and a new one installed (they told us to throw it in our trunk and return it to Lowes, as if). Why did we pay to have this warranty when both the product, and the warranty are junk? Never, ever again! While Im at it, I should add that our range, and refrigerator are also made by Whirlpool, and those too, are pieces of junk. I guess were bucking up, and scheduling a new installation. If there are any further problems, I will be contacting an attorney.

My Whirlpool Duet washer was purchased on August 2006. The first one had to be replaced as it flooded my laundry room on the first floor and the basement – not once but twice. When I was told that they would send yet another service person out to try and fix it, I told them it would be at the curb and that I was looking forward to filing a lawsuit. Then after being on hold for forever and getting the company that sold me the unit involved, they replaced the washer at no charge.From day one I hated this washer machine. If you failed to take the clothes out immediately after washing, they would get a musty type odor and I never felt the clothes got cleaned enough. Yesterday, I went to empty a load of laundry and it was soaking wet with water pooling in the bottom of the barrel. Today, I had a certified Whirlpool tech come and look at the washer and he told me to put it at the curb as the rear bearing is shot and needed to be replaced. He also told me not to buy another front loader and the cost of the repair would be approximately $800.Thank you to Whirlpool for manufacturing a true hunk of crap that, may I say, cost me $1300. I will make sure I tell everyone I know that your products are crap and I would rather wash my clothes by hand. I did call the WP customer service number and was told that this is unheard of and that these machines rarely have any problems. After just reading multiple complaints of the exact same problem, I now know that this product is inferior and the design of the bearing assembly is seriously flawed. A major recall is probably in the near future and Whirlpool is hoping that most people will just dump them before the recall is made public.

My Whirlpool has all basic features and works for household jobs. It is extremely useful for routines like towels and clothing. It also works gently enough to launder curtains and goose downquilts. Operations are very simple and the controls make it very simple.

I purchased a high dollar built in side by side fridge with custom panels in 4/2005 and had my first service call in 5/2005. Since 2005 we have had 11 service call mostly for defrost failures and over temp. readings. From 2011-11/20/2013 we were issue free then the fridge over temp alarm sounded and we could not hear the fan motor. We had the certified tech come out to evaluate and found that the main control board needed to be replaced. Kitchen Aid/Whirlpool no longer make this item and forwarded us to Core Centric solutions to have a new one built. After speaking with the certified tech who had been out to service our fridge 11 times he informed us that these boards in his experience have never lasted more than a year. We spoke with a customer service rep a Kitchen Aid and asked about a prorated discount on a new built in fridge and she said it seemed reasonable but after checking for authorization informed me I needed to have the board rebuilt at my own cost and that even though this typically takes about 4 weeks to build the fact that our family would be without a fridge is not Kitchen Aids problem. 6/20/2005-over temp/not cooling call (replaced defrost thermostat) 9/2005-over temp/freezer iced over in bottom (freezer decided and drain unclogged) 10/05-over temp/not cooling (replaced fan motor) 9/06-over temp/freezer iced over in bottom (drain line decided, kitchen aid had no advice on how to fix) 10/06-over temp/not cooling, ice build up (whirlpool recommended replace heat kit and bimetal) 11/7-over temp and ice buildup in freezer with leakage (adj to drain pump and defrost drain basin made) 11/07- over temp and freezer icing over (whirlpool sent out a new heater probe) 6/08-over temp and ice buildup (bimetal and foam block replaced) 10/09-over temp, lights and motor shutting on and off (replaced defective board) 10/09- fan making excessive noise (ice buildup found on evaporator fan)11/13-over temp ice buildup in freezer, burning smell from fridge and no air movement or cooling in either compartment (need board rebuilt as on 10/09)Board no longer available from whirlpool, must be custom built at owners expense and will take up to 4 weeks. D/t continuing issues and whirlpool not willing to help the customer with replacement I would highly suggest no one buy a Kitchen Aid fridge.

The dryer is okay but the washer is no good. Doesnt save water because clothes have to be washed twice. Sometimes thrice to get them clean. Cycles are longer therefore more energy used. More water, more time, more energy. Terrible design. Useless piece of junk.

We just wanted a black, good looking microwave, so far so good. It been easy to keep clean and cooks food fast. We actually installed it ourselves and it was pretty easy. It hasnt broken down or given us any struggles.

Twice purchased washers Cabrio and both after 5 to 6 years break down showing f1, f2, UL codes. Shame on this company. They refuse to give us a particular time to fix it and have the nerve to charge us for the visit without fixing it first.

Within 5 months my 850$ dishwasher broke. 2 months to repair and 15 plus hours on the phone. Warranty is cryptic. You must allow them 30 business days from when they order parts. Buy Bosch, wish I did!

No matter what I do after I wash clothes on quick or deep water cycle or even running the cycle over again, the clothes are left with soap residue. This is very annoying, particularly on dark clothing because it stands out. If I could start over, I would purchase a washer with an agitator. I watch the clothes as it goes through a cycle and the clothes stay in the same position...no wonder they dont get clean. What a ripoff!!

Problem of refrigerator is working good for a few days, then the freezer is all melted down for a few days, then back to working good again. Model: FD2560HES. Serviced on and by: 7/16/2015 - ** - told me the controller board is bad, need to order part. 7/23/2015 - ** - replaced the controller board. Resulting same problem. NOTE, which means my old controller board is as good as the new one. 7/30/2015 - ** - opened the freezer, back of refrigerator, told me the compressor is no good, gave me an estimate of total cost $817.86. I did not accept the proposal, and I did not agree the compressor is no good. I called and scheduled for service after and scheduled to have service on 8/4/2015. Then got called from the office, said, Cant come on 8/4/2015 and told me I have to pay the $95.00 first visit. So I called and spoke to the manager, then scheduled for next service.8/13/2015 - ** - when he came, the refrigerator is working fine. He said, Cant diagnosis the refrigerator, told me to call for service when it is not working. He said the compressor is good. 8/15/2015, early morning the freezer is all melted. I called, been told cant service the same day. 8/17/2015 I called the office (1-888-717-9322), requested to talk to the manager, promised to call me back. By this date 8/28/2015, still no call back from the manager. They are located in Michigan. I was told the local office address is: 9582 Katella Ave., Anaheim, CA 92804.

Purchased water heater in 2005 with a lifetime warranty. We had our first problem May 30, 2013. Water would not heat above lukewarm. Called Whirlpool. Our plumber and Whirlpool determined that the temp sensor was defective. Plumber took it off and it appeared it had shorted out as the wires were black and plastic coating had slightly melted in one spot. We had replacement part in 24 hours. Licensed Plumber did repair (2 hours @ $75/hr = $150). Second problem occurred October 23, 2013. Not even 5 months later! No hot water. Hit reset button, turned temp up. No change. The diagnostic light on water heater indicated it was the same problem as before. Called Whirlpool. They sent out repair part which arrived in 24 hours. Licensed Plumber repaired (1.5 hours @ $75/hour = $112.50).I took a picture of the melted plastic caps where the wires screw into, of the housing around the wires, of the melted, charcoal crispy black of the Junction Box in the area that was directly above and covered the wires and sensor panel. It was much worse than last time. Plumber said that the part that screwed into the plastic cap had to be pried out and it broke off. You could see that this might be the spot where the problem started. We feel fortunate that we didnt have an electrical fire start from this problem. Something isnt right. Within less than 5 months, we have spent $262.50 to repair a water heater that has a lifetime warranty. Id like to give this 0 stars. Whirlpool owes us $262.50 and it might be more before this is all said and done.

Bought a side-by-side with extended warranty model ED5VHEXVB01. I had a problem with the ice door. They came out, said they saw a bug, left no comments made, received no word from company. Finally, I called them to be informed on the bug problem. They canceled my warranty with no refund given. Now this will be the 3rd time I have to buy. The starter/overload relay fridge is only 4 years old (out of my pocket). I was told by a parts company this problem the company knows about and will not resolve. My advice is RUN, DONT WALK, away from ALL Whirlpool appliances.

I bought my Whirlpool washer/gas dryer 13 years ago and up till now I havent had one service call or repair done on either one of them. I have owned a Whirlpool washer/dryer before and I didnt have any problems with them either. When the time comes and I have to buy another set, there is no doubt in my mind that I purchase Whirlpool products again!

Do not buy anything Whirlpool makes. I purchased a new home and new appliances. In less than 4 years motor is gone in dishwasher. 6 weeks later I have another leak that has ruined my hardwood floors. My fridge is making all sorts of weird noises and alarm is going off. They are coming to ‘look’ tomorrow. And my washing machine is no longer draining. Whichever you buy from check how the extended warranty works... Trail Appliances Calgary uses a company that is horrific to work with, doesnt have a human to talk to and wont acknowledge you unless you pay $149 upfront. RUN AWAY!!!

I purchased a Gold Star Whirlpool Refrigerator from Sears which was installed on July 1, 2010. The freezer was icing up along seams, so sealant was used. However, now I noticed after 14 months that the interior refrigerators lining is fracturing throughout the sides and bottom of the refrigerator. Not at seams but all over fractures, spanning 10 to 3 to 2 on the bottom and side of the interior lining of the refrigerator.Sears answer is more sealant, and Whirlpool does not take any responsibility in designing a defective liner since it is pass the one year time frame. This causes your refrigerator to be on more often, because of the cracks. Unfortunately, the consumer loses out. Both representatives were nasty and when I asked for a supervisor from Whirlpool, an incident report was written, however I will not ever be able to get a copy of it. It will be considered an internal document. It is a great setup between Whirlpool and Sears having defective appliances made to last a year, and Sears to win with warranty agreements for the life of your appliance of $250, for one year coverage. When you buy the warranty and have a lemon, Sears doesnt replace it, My suggestion to consumers is to buy a tube of sealant.

I replaced a 4 year old Whirlpool dishwasher with a new Whirlpool dishwasher on 01/18/2019. July 2020, dishwasher failed. Finally got Whirlpool to send out a repair technician and was advised that the sump and motor had failed. This is after only a year and a half. Whirlpool will not back their product because I did not send another $200 for a service plan. So basically whirlpool cant even guarantee that their product will even last a year.My 4 year old dishwasher had the same issue which is still unacceptable. I have a Whirlpool refrigerator that almost burned down my house and just replaced a failed Whirlpool stove with a Samsung. I wish I could say what I am replacing this dishwasher with, but I am too frustrated to even look for a replacement after only a year and a half. Replacement parts will cost $250 just for me to do it myself. Do yourself a favor and research the product. Should you spend more? I cant answer that. I have seen 20+ year old Frigidaire dishwashers still working. I honestly dont know what brand to get, but I do know that I will never purchase another Whirlpool product again, and neither should you.

Purchased a new Whirlpool built in microwave oven model WMH 310 17 AB-1 in July 1, 2013. As of February 2014, the glossy black finish on this microwave is dull where the finger push controls are and scratched up along the top of control panel and top front of door. We only use a wet cloth and towel or microfiber cloth to clean this microwave; nothing that would be abrasive so very disappointed in this product. It looks quite ugly for a new appliance. I did not anticipate how delicate the outside surface would be - never in over 30 years have I had this problem with another appliance, even stainless steel does not scratch like this.

Read reviews on the same washer (Cabrio Whirlpool) that I had purchased in January 2017. I have the same problem everyone else has with it, not cleaning the clothes. It was such a disappointment. Had a Whirlpool front in loader for 15 years. Loved it! But the washing machines without the agitator on it is a laugh. What person thought up that design. What a joke on the poor unknowing people that purchased one. Im also upset at G&H Appliances for not standing by their products they sell. Found out that Lowes has a 30 day satisfaction guarantee on what they sell. Not buying from Lowes and buying a washer without on agitator on it. Was two big mistakes I made. I wanted to help out a small local business, but wont be doing that again. They sure are not worried about me.

Purchased 11-02-2016. This Whirlpool/Kenmore dishwasher is falling apart. Top rack wheels are totally broken, ordered parts 4 times, gave up. Now they are held together by gorilla glue. I have gone through 3 gray plastic end caps for the top rack runners. Now one is contained by a plastic slip tie. Last week it started leaking. Sears was totally useless. Whirlpool keeps sending me back to them. Now, I have to go buy another new dishwasher. It will not be a Whirlpool. Next time getting the extended warranty.

I waited years to buy this machine. I hate it!!! I agree with the other bad reviews. It destroys clothes. There is barely enough water in it to cover the bottom of the machine much less the laundry. Even deep water is a joke. It does not clean. I put it on the hottest water temp and I can put my hand in there and it is barely warm (it is not my hot water heater). My lightweight comforters come out all tacky and grungy in the middle. The softener dispenser (I use vinegar) dumps in the laundry (no it is not over full) (no I do not slam it shut). I can not let anything soak because the machine will drain after a few minutes and all my detergent, scent crystals etc. are all wasted. I feel like I have to take a survey and complete a questionnaire every time I do laundry. Can someone tell me how to put a comforter in there and leave that little middle eye open? They say the water saver is government regulated? Yup I need the government to do my laundry... I believe in saving water. I have a water saver toilet, shower, faucets. However I can not clean dirty jeans in a gallon of water. My clothes do not even get wet. How does whirlpool get away with advertising this machine can do king size comforter? The gentle cycle will tear apart anything I might put in there because there is no water and that blooming thing just twist and turns so it tears anything delicate. This is the 21st century. I think I should not have to babysit my washing machine. Why should I have to readjust everything in hopes it might be almost clean??? Place this here and that there, wipe the lint out before doing dark laundry. This machine belongs in the dark ages. It is so complicated yet it achieves nothing. A big rip off. I so tired of crying over this purchase. I hate this machine!!!

I bought a 50-gal. Whirlpool electric hot water heater about 6 years ago from Lowes. About every two years, something goes bad. So far, I had to replace electronic control board that sits on top of heater twice. Then the heating element went bad. Well, this time, the electronic control board started to smoke and melt. I was home so I smelled something melting and found it. What would have happened if I was not at home? I have dogs that are like my kids; they could have been killed. Whirlpool wants to send the replacement parts knowing this part is no good. Do not buy a Whirlpool electric water heater! Now, Im scared the next time I wont be at home to find the thing smoking. I dont have money to buy a new one. How many other people have the same problem?

I purchased this Whirlpool Cabrio washer three months ago from hhgregg. If I hit the lottery, the first thing Im going to do is take it to the dump and buy a new washer. There is no way to wash a load of towels in this machine. I started a load at 7:35 this morning and it is now 9:53 and Im still dealing with the drain and spin cycles. Over and over, I try to get it to spin out enough water that I can put the towels in the dryer. I should have suspected something when I saw that the washer even had a separate drain and spin cycle. It should have told me something. Its a piece of junk. Never again. Im back to Kenmore.

Purchased both Cabrio washer (wtw6200sw2) & dyer brand new in 2007 for $1200. Within 4 years the motherboard went out. Whirlpool didnt want to fix it. They said it was past warranty. After many complaints to corporate, they sent someone out to repair it for $496 (they paid). Repairman said these models had motherboards from Japan & Whirlpool was aware of the many issues, but wouldnt do a recall. 2009, the springs went out, 2011 F codes began to appear. Clothes dont get clean; not enough water. 2014 & 2015 DU & DL codes appear. Now I need a new Lid latch assembly. These washing machines are not worth buying. Never again will I buy another Whirlpool!! My mom had an old Kenmore that lasted 20 years and only needed a replacement belt. No more fancy high end washers for me!

I purchased my whirlpool washer on 01/24/2011 and I purchased a 5 yr extended warranty at the time of purchase. My washer broke down. I called the whirlpool co. After 5 mins getting through the phone prompts and another 30 mins on hold I finally spoke with a rep name Ashley who state that there was no account or record of my warranty. She connected me to another department where I spoke with Eva. I was advised that since the company that sold me the warranty was out of business whirlpool would set up an account for me if I faxed the information documenting my original purchase. I faxed the information, waited three days without a response. I called today went through the phone prompts and could not reach the reps I spoke with before. The reps today were not helpful and refused to even try to get me to the reps I spoke with before. I was advised that the previous reps provided inaccurate information.If an appliance comes with a one year warranty and a consumer purchases a 5 yr extended warranty should it be added to the 1 yr or is the first year included in the 5yrs? Wouldnt it only be a 4 yr extended warranty if that were the case? I am very disappointed in the lack of quality of my washer and misrepresentation that was communicated by whirlpool reps. At the very least they should answer the phone promptly and honor the commitment to repair products. This is the case number (**) I was provided the first time I called, but it is not recognized by the reps I spoke with the 2nd time. I was provided 866.368.6478 as a contact# and a fax#. I faxed my receipts to that number as instructed.

I have had this range since 2008 and used the self-clean last week. (I dont use the oven that often) Since the clean it has not heated up to required temp. I just called Whirlpool and a tech is coming out this Friday (Nov. 15th 2013). If it is determined to be the self-clean that did in fact cause this, the tech calls for an authorization and the repair is covered by Whirlpool. I will report back what happens.

We recently bought a home and our dishwasher came with the home. We saw our basement leaking and got 2 plumbers come over and check the pipes out, paying almost $600, only to realize that the leak was actually from the broken plastic in our dishwasher, and not any pipe. When we called the Customer Service to get it replaced as it comes with a 20 year warranty on the plastic body, they said they would replace the part, but I would have to pay $81 for the first 15 min & $19 every additional 15 min. for labor, which means I would end up paying at least close to $400 or more, depending on how long the technician takes to replace the fiber body. Neither their policy nor warranty make any sense to me. Its frustrating to see that in spite of being covered, I would be the one paying money out of my pocket.

I had my old agitating washer for 8 yrs that went out. I liked Whirlpool so decide to try their washer. Found the Cabrio washer (SWS5000WO) and thought without the agitator it would give me more room for clothes to wash better. Boy was I wrong, no matter what cycle or what size load it is off balance on the very first spin. I have to stay near by to stop the washer before the first spin adjust the load and start over again. Jeans and towels are impossible to clean. It throws the tub so bad it has pushed the side out. I have checked the balancing rods and they are fine. After reading other complaints realize the Cabrio washers are terrible. I will be looking for a refurbished washer with an agitator and doubt I will buy Whirlpool again. They should have a recall on these machines. They are terrible.

In August 2011, I purchased and had installed a Whirlpool Wall Oven RBS305PVQ04 for $1000+. In July 2014, the oven failed with blown internal fuses and a thermostat $225+. In November 2014, the oven failed again, this time with a failed controller board. Whirlpool claims there are no replacement parts after just three years! In calling Whirlpool customer service for help, they basically said tough luck! NO parts, NO adjustments, NO service, you own a boat anchor. I tried to buy American; boy, was that a mistake. So it cost me $415 per year to own this LEMON. DO NOT DEAL WITH THE WHIRLPOOL COMPANY!

Bought this machine at Lowes as it was recommended by the salesperson. The machine broke down in 2 months due to a control module. Besides that, the clothes do not get clean! They come out with all the stains still on them. The water does not even get the clothes wet! And they smell. Called Whirlpool up and they sent out tech 2x and said there was nothing wrong. Went back to Lowes and they will not honor my claim to replace the unit. I now have to purchase a new machine since this one is useless. Never will I buy a Whirlpool again and dont you either!!!

We bought a Whirlpool Range gas stainless steel five burners on top. We haven’t had it a year and the paint is chipping off of it. It’s starting to rust now. I know stainless steel ovens. You have to clean them specifically with certain chemicals which I do so there should be no reason why it’s rusting and the paint coming off of it. Hasn’t even been a year yet since we bought it.

I purchased GMH6185XVS microwave in Dec. 2011. It was installed in January 2012. This was for a remodel kitchen with all Whirlpool appliances. In August 2014, we discovered the micro would not heat. I called Whirlpool as directed by Sears. I am told I have to call a repair service and pay for it. I have a 14 year old Whirlpool in my home. We have never had a problem with it. I had a Whirlpool micro in my previous home; never a problem. This is a second home that we hardly ever use. We are two adults. My daughter had the same problem with the same microwave. I am very upset with Sears as well as Whirlpool. Even if I used this machine everyday, it should not break in 2.5 years. Shame on both Whirlpool and Sears. I will never purchase another Whirlpool product again. I will be telling everyone I know.

I have had this Whirpool Cabrio washer now for one year. Clothes always come out wrinkled (even after drying). It leaves clothes unclean and leaves white streaks in clothes. Water level is so low in, that it cannot rinse or wash clothes properly. After washing towels, when removed to put in the dryer, soap is left in towels. I have had a repairman here, he says the design is bad, yet reports works as designed. Dont buy this washer. This is a piece of junk!

We have a wtw5500xw2 washing machine we bought 03/2012. We can no longer use it. The machine would not spin or agitate so the clothes do not get clean or get the water out and after the cycle is done we have to wring them out after to be able to take them to the laundromat. So two repair companies and 3 months later we find out that it is the wiring harness that is the culprit. After a new motor and a shift actuator, we contacted Whirlpool only to be advised that the washing machine is out of warranty and that we are out of luck. If the company has a known issue about these wiring harness they should be looking into it and changing suppliers or offering to replace the wiring harness at a discount to its customers. I will not be buying a Whirlpool appliance ever again. I would recommend going with a Kenmore. I have had a Kenmore dryer that I got 19 yrs ago that we got used and only had to replace the heating element.

I bought a 40-gallon hot water heater in November 2007. First problem I had with it was in 2009 when the pilot wouldnt stay lit. They sent me a requisition number to take to Lowe’s to pick up the part (igniter) and gave me a service number to give to the plumber to fix it. Plumber actually told me these heaters were junk and this wasnt the last problem Id have. Last Sunday (January 2012)--here we go again. Pilot went out and wont stay lit. Whirlpool is telling me its because I have a draft. Yeppers, that must be it because after they had me (arthritic 53-year old) and my disabled husband performing circus acts trying to relight it, then it was the filter on the bottom, then it was a draft. Last time I tried to light, which really someone as blind and disabled as me shouldnt be doing anyway, I about blew up. I hate getting ** by big corps. I filed a complaint with state Attorney General. If that doesnt work, hell, I think Ill take both Whirlpool and Lowe’s to small claims court. What do I have to lose? $35? Their fancy-schmancy lawyers will probably charge them a couple grand for their efforts. Im sick and tired of getting the short end of the stick. Since when is a hot water tank supposed to last a mere 4 years? Oh, by the way, Whirlpool says it’s all on me now--well see about that. First of all, both of these chumps just lost a customer and I Facebooked by friends about this pleasant experience plus included a link to this page. Consequences are all mine, I guess. Its pretty swell bathing in a sink full of water that you heated on the stove. I dont have any money because Im too busy giving it all to big insurance and big pharma right now. What a country!

I bought my refrigerator model #WRV986FDEM, in October. It has not made ice in over a month. I think its very unfair to purchase a product and not be able to use it. The technician has been out here twice and the situation is still not resolved. I understand that customer service is not a strong suit of your company but I am not a customer to be taken lightly. I paid almost three thousand dollars for this piece of junk and I want it to work properly. I find it unacceptable that the technician just left and the situation is not resolved. I will be posting my displeasure on every site I can today since I had to take yet another day off to accommodate you and your inferior product. ALL I WANT IS ICE from a fridge I bought 4 months ago. In the words of our illustrious president. Very, Very BAD.

ECO friendly top load Whirlpool washing machine - I bought this machine September 2013. Now it has a continuous clicking sound. It appears to be the lid locking mechanism and the washing machine will not turn on. It is under warranty and I am finding it hard to get a repair service in my area that is directed to Whirlpool to come and fix it. The only appliance repair in our area states that they will charge for trip and service if they find that is not a defect within the Whirlpool perimeters. I could be charged up to $200 for trip and service which is half of what I paid for. Whirlpool states this is not the case, and I am now having to wait a week to even set up yet another appointment. I have other machines that lasted 7-10 years until they wore out. I am frustrated and what could be a simple fix has turned into a financial nightmare.

I have had a terrible experience with fridge Whirlpool. Two fridges have been delivered to me in bad condition. The first one was aesthetically awful (looked old and used) and the freezer didnt work so it was exchanged. The second one works and it looks ok but it makes very loud noises all day every day. I live in an open concept condo and this fridge sounds like a train for more than an hour more than 5 times a day, it is terrible. I have been calling customer support for a solution and first of all, there are no technicians in my area, and since the fridge works as designed there is nothing to fix so Im stuck with a terrible noisy fridge that I hate and destroys my day which I paid a lot of money for thinking that the brand meant quality but it doesnt. Customer support doesnt respect the customer and their answer that the first works as designed makes me understand that Whirpool designs bad quality fridges. I have never heard a fridge making these noises, not even brands that are less named than Whirlpool. For your inner peace, I recommend you to stay away from Whirlpool-Maytag fridges... If the fridge is in bad condition (but working) youre going to be stuck with it. The brand doesnt really mean quality and support... it just means more expensive.

I purchased a Whirlpool water heater on 9/30/2011. It is leaking at the point of cold water entry and is spewing a brown colored watery substance, leaking on the floor.

Best dishwasher Ive ever used, Quiet, extremely clean, priced well for the quality. A really gorgeous piece added to my kitchen. Would highly recommend this product. Up to date. Easy to use. Sleek design. Would be beautiful in any design.

Weve had this Whirlpool 5000DW1 machine since June 2017. Never fills with enough water no matter what cycle you pick! Clothes come out with DRY areas on them! Obviously not clean. Who would design a washer that you put soap in and clothes right on top of that! Seriously, how ridiculous. I will forfeit the money spend on this junk if its possible to find something built today that cleans clothes.

My Whirlpool French Door refrigerator will have its TWO year old birthday on September 15, 2015.. only if it lives that long! On August 8, one month and one week short of its 2nd birthday the compressor died. Of course the manufacturers warranty expired after one year. Thankfully, I purchased an extended warranty through the retailer. While this will cover my repairs, there is nothing that will cover the hundreds of dollars worth of spoiled frozen and refrigerated products which had to be discarded. I will NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT!

I purchased my Whirlpool Duet in 2007. I have since paid more than what the washer costs in repairs. Now, the metal that braces the basket has corroded and fallen apart. Ive read that this has happened to many people and since then the company has changed the part. However, they are unwilling to send a new part to me. I will never buy a whirlpool appliance again.

I brought a water heater from Lowes in 2011 and I had a 6 year warranty on it which will end November 2017. Well now the water heater is leaking and they wont replace it because of the location of the water heater and they saying I need to get a direct water heater. Well what is the use of having a warranty if I cant get another water heater. I will never buy another water heater from Whirlpool! I cannot afford to get a direct water heater.

Easter is in five days. Our dishwasher purchased in December 2014 is not working. It has been broken since December 2015. Repairmen have been here THREE times. We were told that our warranty only covers parts and repair. Our dishwasher does not wash dishes. We went for a more expensive model and it didnt last a year. Whirlpool, remember your commercial?

I would like to know if anyone else is having trouble with the broiler unit. The unit quit working. Thankfully I had purchased the extended warranty. The guy came out, cleaned the orifice and called it good. The next day I went to use it, and guess what, it did not work!! So we thought maybe we needed to leave the oven door cracked open a bit... Well, guess what... It melted two of my knobs!! We called, got another guy out here. He checked everything. Even pulled the stove out to check out connections. Then he informs us that you can set the broiler to whatever temp you want. Thats new. So again, we try the broiler.... Guess what... It got to the temp and clicked off. Now I ask, how does one broil a steak if it does that? I did call Whirlpool directly and got nothing. Our model is WFG361LVQ2. So please, if anyone out there knows that this is how it is supposed to be... please let me know.

I had a Whirlpool washer for three years that I bought at Sears and it started making a noise. I called Sears repair and they said it was the bearings. Would cost 600.00 dollars. The machine is still running making a noise are there more in a machine. I will never buy a Whirlpool product. I just lost my husband and I cannot find the bill but I am calling Sears tomorrow.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

The exterior look of the refrigerator (WRX735SDBM00) is impressive and the stainless steel does not show finger prints easily. It has two french doors on top, a middle drawer, and the freezer drawer on the bottom. The interior is 25 cf, but there isnt much space, even with reconfiguring the shelves, and the crisper/meat drawers are so small, that a large bell pepper wont fit. When one French door is closed it pops open the other door, which then does not close back tightly. Although there is an alarm system to warn a door is open, it only works if the doors are open and not just cracked. We have to constantly push on both doors to be sure they are closed tightly, even after washing down the gasket to get a better seal.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

We bought a Whirlpool Gold French Door refrigerator in 2010. Just when the warranty period passed, the refrigerator started leaking water from the bottom floor. Initially, it only leaked about once per month. But as time passed, the refrigerator started leaking more often, and now its leaking every 2-3 days. I saw many people complaining on the same problem and some of them even submitted since 2006. I dont know why Whirlpool doesnt resolve this issue in many years.

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

We bought our Whirlpool Refrigerator a little over three years ago. Within a few months we started having problems with the unit. From ice maker issues, cooling and freezing. Initially the frig was covered under Whirlpools 1 year warranty. Then our extended 3 year warranty kicked in through HH Gregg which they supplied for free because of their poor handling of the initial sale. We have lost track in how many times a repair man has come out to work on the refrigerator. In the last year alone its been at least 8 times. The most recent problem had been the freezer not defrosting properly to the point where we had to store food in our neighbors freezer. The repairman has tried everything he knows and is stumped. Well our extended warranty has run out but theyll continue to work on the problem as long as we report the issue within 30 days which creates a whole different set of issues. The extended warranty states they will replace the refrigerator if it has the same problem 3 times. However what they dont tell you is that if you call BEFORE 3 time period its considered a recall and that doesnt count towards the 3 strike rule. We contacted Whirlpool and they wont cover the refrigerator because the repair company isnt on their approved list. Really a Sears repairman isnt approved? So buyer beware of a lemon Whirlpool Frig! They seem to have a way of not covering their product.

I have automatic Whirlpool washing machine since 3 1/2 years I am using. Now 2 times electronic board came problem so how many times can change like this? Why they are manufacturing if they cannot solve this problems? Should not sell in the market. This all not coming free and need to struggle. Whirlpool products all very bad appliances.

I purchased a brand new refrigerator model # WRX735SDBM00 Ser # K51621170 on 30 June at Lowes. Paid about 1600.00. Within 5 days the ice maker was no longer functioning. I called the service department and a lengthy ordeal commenced of trying to repair. It is now 13 August 2015 and I have had over 10 visits from a technician and I still have no ice. I made a terrible mistake in not returning the appliance to the store within 30 days so now it has to go through the process which means that now I have to continue to wait until the technicians deem that this appliance is not repairable anymore before I can attempt to get a replacement.In the meantime, we have been inconvenienced, aggravated not to mention not be provided a product that works with no future date where I can get this appliance repaired. The local store management have been great to deal with and are trying but their hands are tied until the manufacturer determines they cant fix. In the meantime, the consumer is continuing to wait for the repair/replacement. No one seems to care or has there been any discussion of some compensation (not necessarily money) for the aggravation and inconvenience I have endured. Something is just not right. Suffice to say, never again will I buy a Whirlpool. HORRIBLE EXPERIENCE.

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

We bought a new Whirlpool refrigerator about three years ago. Because of space, we had to purchase one with a top freezer and also with no ice maker. First of all we didnt realize it was much deeper than our old Kenmore so it stuck out further into the kitchen space. That was not that big of an issue. At first everything ran great including the top freezer compartment, or so we thought. Then we noticed that when we had ice cream in the freezer and put water in ice cube trays to freeze, the ice cream would get very very soft. This continued to the point that now anytime I put water in there to freeze ice cubes I have to turn up the temperature to keep the ice cream frozen. Once the ice cubes are froze, there is no problem, but they take at least six hours to freeze. Then one day when a young child slammed the refrigerator door closed, the freezer door popped open about an eighth of an inch and then closed again. So, I tried it. Anytime you close the refrigerator door a little too hard the freezer door pops open. I then tried the dollar bill test to check the strength of the seal. The bill pulled right out of the door with very little effort. So, is the problem bad seals, bad design, or bad quality control, or what. How can I be assured that the frozen foods in the freezer are being frozen as solid as they should be. I know they dont freeze solid enough in the freezer door. I will eventually dump this refrigerator and go get another Frigidaire. If we have to get one with a bottom freezer, we will just have to rearrange our kitchen to accommodate it. But, having to turn the temp up and down every day is ridiculous. I have had issues with food close to the walls in all refrigerators slightly freeze, but never had an issue with keeping things cold enough. I will never buy another Whirlpool refrigerator, stove, or anything else for that matter. I have always had good luck with Frigidaire, so I will stick with what I know works.

Whirlpool Gold Series French door, bottom freezer. - This fridge is beautiful. Thats as far as the pros go for it. The Freon is leaking and cant be repaired because of where the leak is coming from. I can always tell when its time for a recharge because it leaks water profusely when at a low charge (every 4 to 6 weeks). We paid over $1800 for this fridge back in 2013. It has been just over two years and we are now having to replace this fridge. I cant express my frustration at this point. Whirlpool wont do anything to help us. They told me, You are out of warranty, and thats all they have to say. Thats over a thousand dollars a year to own this POS when you consider taxes. Over $1250 a year when you consider the service calls along with it. I will not purchase another Whirlpool product ever again. I am disgusted by this company and their refusal to stand behind their product. They have literally stole money from me and are laughing about it. Do yourself a favor and stay far from Whirlpool.

We bought a new Whirlpool gold gas stove. We had just finished redoing our complete kitchen, and thought it would be nice to replace appliances. I thought Whirlpool had a reputable name and good service record, but clearly, I should have checked. Three months after installing the stove, the handle pulled right off the door. We called the service tech who came in, took the door apart, and replaced the handle, but for some reason, installed different and incorrect screws for the door. Over the next 7 or 8 months, the handle pulled off twice more, and we repeated the cycle. At this point in time, we had been experiencing a situation where the stove would shut itself off. Bear in mind, it is less than 18 months old. Even now, the oven heats, and mid way through cooking anything, it decides to shut itself off. Clearly, there are issues with Whirlpool products, and when I called them, they want to do nothing about it. They jockey me around, from one service person to the next, frustrating me as I have to retell the issues to each new individual, and then they only tell me a replaced board, which would cost more than $600, is the way to go. Ive had this stove for 2 years, and it is seriously the biggest piece of garbage anyone ever put out on the market. Apparently there are no recalls on it, and so apparently, Whirlpool is more interested in ripping off their customers, than standing behind their product. I am currently seeking permission in a local paper to write a public service piece. I hope people will read it, and avoid this company at all costs. I hope whirlpool enjoys it. I dont know how they have turned a blind eye to all these complaints. As far as what I have read, with regards to other whirlpool problems, exploding glass, dangerous fumes, etc. They should be investigated, because what they are pulling off is criminal. If I want someone to steal from me, Ill leave my doors open, and let them come take me for what I have. I dont need to support a company that is stealing from me, while they wear smile on their face.

Stainless steel, easy to adjust, cools very well installed in a RV instead of standard RV fridge. Took a little bit of carpenter work to make Whirlpool fit but well worth the effort. The only problem I have with the fridge is that whirlpool wont honor the warranty because it is installed in a RV.

I have a Whirlpool Duet Steam Washer that will be two years old in September 2013. It has been making terrible, loud noises during the spin cycle for a few months now. Repair tech told me it was the bearings and very costly. It will cost me over half of the original cost to repair a less than two year old washer. This is my second Duet front loader from Whirlpool. The first one was a drum issue and the rod ended up snapping. Again, very costly so I bought a new one. I should have learned my lesson the first time. I do not agree with extended warranties and it is just an additional money maker for the manufacturer. They should be making the product so people do not have to purchase those. Anyway, back to the washer at hand. I refuse to spend that much on a newer washer and will never purchase a Whirlpool product again. I will let this thing bang for as long as it is going to last. Unfortunately have also just purchased the dryer that matches this washer since I still had the old model Duet Dryer, so kind of stuck with them. Spent an hour and a half yesterday on the phone talking to people at Whirlpool and they really dont care if you have an issue or not no matter how old your machine is. They just want you to have purchased the extended warranty or forget it. There should be a recall and they should be helping these customers who all seem to be having the same issue. Done with them!!

Whirlpool Duet - they are highly rated and are aesthetically pleasing. Highly rated, they are expensive, my last Duet w/d didnt last as long as expected. Ive had to repair both machines once since I purchased them. Good quality is of utmost importance, plenty of washing and drying options, front loading washing machine, full size extra large capacity, attractive machines, good reputation for quality and lack of repairs.

If you are searching for a top freezer refrigerator that works and keeps the food cold, do not buy this brand. I recently ordered a brand new refrigerator from Home Depot, the Whirlpool brand. It was set to standard factory settings, and I let it sit plugged in for 24 hours as required. The fridge was remaining in between 45 to 50°F, and I let it run for another 24 hours after filing a complaint and talking to the people at Whirlpool. The fridge still cannot get beneath 40°F, though the freezer seems to be okay. I spent almost $1000 on the refrigerator, and I’m very disappointed in the quality that this supposedly good brand produces. I went on Facebook marketplace, found an old 1995 Kenmore and bought it for $50. It works so much better than this brand new, fancy looking refrigerator, because back decades ago is when they actually took the time to make quality products, and didn’t make the crap that they do now that breaks down instantly or after only a few years. Unfortunately, and my researching has confirmed this, appliance manufacturers today create bad quality products that break down shortly in order that you will have to purchase more of their products after only a few years. Refrigerators used to last decades, now you’d be lucky if they lasted maybe 8 to 10 years. Trust me on this, don’t waste your time on this brand. A refrigerator should have no problem on factory settings getting at or below 40°F within 24 hours. DON’T BUY THIS JUNK!

When we moved into our new home in May of 2012 we needed to buy appliances. After much research we purchased all Whirlpool appliances at Lowes. After a year and a half our Whirlpool model WRT5L1SMYFOO failed to freeze or keep items cool. We called Whirlpool and they connected us with a technician who said it would cost more money to fix than buy a new one. He said that we got a bad one. We called Whirlpool again and received no assistance. Refrigerators should last more than a year and a half! I have seen other complaints on this model and have yet to see any proof of restitution from the Whirlpool corporation. This is complete consumer abuse. Some sort of action needs to be taken against Whirlpool. This corrupt behavior is the downfall of our country.

Extremely disappointed in Whirlpool oven! Built new home and this was recommendation by BAC Appliance. The oven does not self-clean well at all, and my spills are minimal. Deposits between glass doors that cant be removed. Oven is barely cleaner than before I cleaned for full cycle. Oven suddenly shuts off for a short while and then restarts. Steam comes when using lower oven and removes finish on upper oven. I expected Whirlpool to have a quality product. Definitely not! BAC really had no answers for me.

We bought this dishwasher only 18 months ago and its not worth the money we paid. We have had cheaper models that cleaned way better and didnt need as much maintenance as this one. We already had to spend another $410.00 in having the motor replaced in it!! When calling Whirlpool it only has a 1-year warranty and to have a technician come out just to look at it is $150.00. It is so hard to see in the part where you put the jet dry it doesnt tell you when its full or empty and no matter what it always leaves the dishes wet after. Our other dishwasher that was a way cheaper model always cleaned our dishes and never left any food on the dishes unlike this model and we even rinse the dishes beforehand! Look for another dishwasher to save yourself money in the long run!

On the 10-05-05, I purchased a Whirlpool natural gas water heater from Lows Orem. The unit has a 9 years warranty agreement. Lows sales S0178JC3 647605; cost $378. Model number FG1H5040T3. Serial number 0515140765. Following installation, the unit has failed repeatedly. Since keeping records of the failures, the unit failed either by the gas control valve or the thermocouple on December 2011, November 2011, April 2010, February 2009, and April 2008. Whirlpool has at all times supplied the parts but denied that the parts are technically faulted. Whirlpool has further rejected all requests to refund me for defective product. The major consequences have been an unreliable water heater. There were periods without hot water. Time was spent involving undertaking repairs.

I have been using Whirlpool products for quite sometime. I had bought a 3 door refrigerator (Protton) about 2 years back. However I am noticing that of late, the vegetable drawer does not cool to the appropriate temperature. The vegetables as a result are spoilt. I am unable to understand what to do. I have checked with the other temperature settings and they are all in the normal mode.

Last year I purchased a Whirlpool washer at the suggestion of a friend who works at Lowes. It was dented and reduced, but my 20 year old Maytag, although still chugging away, was due for replacement. Am I sorry I did! My husband has recently broken his hip and we were caught in Hurricane Matthew just 1 day after I brought him home. We were forced to evacuate. Upon returning with a mountain of laundry, I found my washer lock light blinking although the washer had not been running when we lost power. I tried opening it but could not. I unplugged and reconnected power to no avail. I called customer service only to find we had to wait 2 weeks for a Whirlpool repair person. He arrived yesterday (Oct 26, 2016) and charged $95.00 to tell me this was an almost universal problem with Whirlpools and the company was aware of it. He called this morning to tell me the required part would cost $495.00! The entire washer cost approx. $500. He stated that he thought Whirlpool should have covered the cost as it was not far out of warranty and a known defect, but he could not get Whirlpool to assist financially. I tried calling myself for an explanation of the fact that they knew these machines had a defective part and yet they sold them. I got a song and dance from the rep. Although my husband was unable to help and I am a 65 year old woman, I went out and bought the cheapest machine I could and manhandled it home and connected it. It is afternoon and I am on my 4th load of well overdue laundry, no thanks to Whirlpool. I intend to make this story public through every internet forum I can find. I have a large extended family and friends and I will make sure they do not purchase Whirlpool appliances if they are looking for a good product and good customer service. I will also be sure to never buy a Whirlpool appliance again.

I love my stove and all of its features. My stove is easy to clean and I Love the self cleaning oven. I have a flat top so that helps when it comes to cleaning, not to mention it makes cooking a breeze. I love all the push buttons and how smart my stove is. I highly recommend my Whirlpool to anyone looking for a great appliance.

This oven/range (W10665261B) has a cleaning feature that DOES NOT WORK! Do not buy unless you want to hand scrub the oven without any cleaning products. No one at the company cares. I will discard the oven.

Five years ago, I decided to splurge on a really nice (expensive) over-the-range microwave during a complete kitchen remodel and had the Whirlpool Gold Velos Microwave GH7208XRS installed, thinking Whirlpool would be a reliable brand to replace our 18+ year-old (still working) Kenmore countertop model that we had used previously. About 4 months ago, after a couple of mysterious cases of the control panel going haywire (turning on by itself in a different modes), it started pouring smoke out the top and service was called and the magnetron and inverter were replaced to the tune of $482.Fine, things happen. Yesterday, while opening the door, the handle snapped off and (upon closer inspection) I noticed cracks around all sides of the door frame - see photos. After reading about similar complaints about Whirlpool microwaves on this forum, I really feel that this is a defect in materials and should be recalled or at least addressed by the company if they want to maintain their reputation. Right now, I am waiting on their authorized repair service to see what my recourse will be.

I purchased a Whirlpool CABRIO H2Low top load washing machine approximately 12-15 months ago from Lowes in Columbus, GA. I have been very dissatisfied with it from the beginning. I contacted Lowes and discussed the machine and expressed my complaints. I realize that it has a sensor and fills the machine with the amount of water according to the weight of the clothes but have found that regardless of what cycle I place the machine in, it doesnt place over 2 inches of water in the machine. It does not clean the linens, under garments or any type clothes. In fact, it has ruined my designer clothes. It is impossible to get the wrinkles out with an iron. Im very disappointed in the service we have received with this washer.