I bought my Whirlpool gas stovetop in March of 2016. The burner knobs that connect to the stove is made of plastic and all 5 knobs broke within the first year. Each year I have replaced knobs and had issues with the knob breaking and then not being able to tell if the gas is off or on. I have called and talked to people at Whirlpool about this issue several times. Although they seemed concerned they will not replace the knobs and I have had to purchase them through Whirlpool. The gas stovetop obviously has a serious and extremely dangerous design flaw. I have kept some of the broken knobs just to tell others about this terrifying flaw. Again, last night the gas was on for several hours before we discovered it!! I called Whirlpool again and they were unconcerned. The Model is #WCG97US0DS00, Serial#D60509297. Beware and DO NOT PURCHASE this gas stovetop. I wish I had not bought mine.

My stainless steel french door refrigerators compressor quit working and needed replaced after 3 years and 10 months. I had to buy a replacement kit and it cost 400.00. The repairman cost 175.00. I tried to buy an extended warranty but they do not sell them. You get a 1 year warranty. The repairman told me you will be very lucky if you get 4 years out of the replacement. He said all of the new compressors are really junk. Remember when refrigerators used to last 30 to 40 years. Not anymore. It is a money racket. Do not buy anything Energy Star, it is all junk. I have gone through 5 washing machines in 18 years, and I live here by myself.

Whirlpool Cabrio Platinum WTW8800 model - In the words of the service technician who came out finally to service the machine. This machine is a piece of crap that should be recalled from the market. It is a low level-water unit that has no agitator ability in it and does not provide enough water to even slightly clean clothes. Everything must be sorted into the smallest loads possible and even then the clothes dont clean because they beehive into a ball and do not agitate. Technician says the machine cannot be fixed and simply recommends it be trashed (it is 1 1/2 years old). Technician recommends going back to front loaders where at least the clothes agitate. Called Whirlpool for help and was told all system are down...duhhhh. Call back in an hour and Good Luck.

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

I have Whirlpool gas range, model # WFG361LVS1. The igniter went out after only one and a half years of light use (4-5 times a week). I did not buy the extended warranty, so part is not covered. I only asked that they send me the part for free. I talked to a supervisor at Whirlpool (Dave). He said I should have bought the extended warranty. He said he could not help me. He was also very rude. I will never purchase another Whirlpool product.

Whirlpool Slide-In AquaClean Technology - My beautiful, modern oven is no longer. After 4 tries doing self-cleaning my oven was still dirty. I did have to wipe out the water (although I measured it) before I could take the scraper/sponge provided by Whirlpool to assist in the cleaning. Scraper bent - sponge disintegrated and I still have a dirty oven. Called service. My pleasant service tech informed me the water is only to reach 250 degrees! Really! My dinosaur of a Whirlpool cleaned fabulously! New technology has turned mine into an on your knees, scraping and broiling fool. Fool because I bought into the whole Aqualift Technology. We cannot use any kind of liner, etc. This slide-in may look great but the labor required to keep it that way is beyond this OCD person! So much for my efficient new kitchen. May the engineers who designed this technology be ashamed of this product. It is not even a self-steam cleaner!

Had the fridge 5 1/2 years. Freezer quit working was told by 2 different repairmen it would cost $800 to repair. Called Whirlpool, was on hold 45 minutes, literally, both times I called. They could not help me. Called the corporate complaint line. The man I talked to was such a smart **! I finally said I cannot believe you are talking to me like this, I have bought Whirlpool for 35 years. He backed off slightly. Still couldnt help me. BTW, I LOVE my new Samsung refrigerator! Will NEVER buy Whirlpool again.

I purchase almost four thousand dollars on WHIRLPOOL appliances this month. From: HOME DEPOT 114 FEDERAL RD DANBURY CT. Received the items a week and a half ago 9/15/18. I was told to exam item no scratches, dents etc. I did that and had them put in place. I didnt get a chance to use washer until the fourth day. At which time realized it didnt work. Went over to store and they gave me Whirlpool repair phone number. Called and was told they only repair Mon - Fri 8am-4pm. I work every day until 5pm and off weekends. Told Whirlpool repair just that. THEN I TOLD by girl I was speaking to (Whirlpool repair) I COULD JUST RETURN THE WASHER TO THE STORE (Home Depot) MYSELF. I WAS FIT TO BE TIED. I told her, What should I do? Carry it on my back? I have never been treated so poorly. I just moved here from Florida, started a new job. I cant take a day off to have the washer that should have worked fixed. I will never purchase anything else from Home Depot if this is how Im treated, and Whirlpool their customer service stinks!!! So now Im stuck with a washer that doesnt work and a company (Whirlpool) wont accommodate their customer. (Whats wrong with this picture???)

I purchased a Whirlpool Cabrio and a one year extended warranty two years ago. As soon as my warranty ended, my washer started to malfunction. I recently started to receive the F-51 code and the washer shuts down at the spin cycle. I am angry because I spent just under 1200 dollars on a washer a little bit over two years ago and now, it is sitting in my laundry room taking up space. When I called Whirlpool, they told me I could purchase another repair warranty for $316.94, which would take the cost over 1500 dollars for this washer and there was no empathy nor compassion for what I was feeling as a consumer from the customer service rep. I spent my hard-earned money on major appliance purchase and I think that it is only fair that I get more than a two year usage out of machine that was designed to last at least six years according to their website. There is no way that this should just be my lost and cost me additional funds.

If I fix this washer I will have been on 3 motherboards in the 5 years I have owned this machine. That is inexcusable and indicative of crap quality control and manufacturing process. I should not have to replace the control board at these intervals or, within 5 years, at all. I will never touch another Whirlpool appliance again.

I have always had a whirlpool dishwasher and have always been please until my last dishwasher. The part that holds the soap and liquid stuff has broken and also the part that holds the silverware. Been really disappointed in this product.

We purchased this Whirlpool Cabrio washing machine from Sears about four, maybe five years ago and have complained repeatedly. We have had repairmen out numerous times. Of course, they have had to order parts. My clothes are not getting clean and they now have an odor to them. The machine is getting noisier and noisier and it is rocking like crazy (I had to put plyboard underneath to protect the floor) during the rinse cycle. The water sprays out erratically and sprays even slower for cold water, then warm water, which was weird! Thankfully, I still have it under warranty (I got the extended warranty). I am now getting ready to call them again. I will never buy this brand again.

Stainless steel fingerprints and rusting are terrible. The storage doors in the freezer have an open bottom which allows items to slip out which is annoying. The fridge has ample space for all my items without being overly huge for no reason. Great for 1-3 people. The rest is perfectly fine.

I purchased Whirlpool Washer WTW4815EW on December 29, 2015 for my tenants apartment and by October 7, 2016 it was not working. I called Whirlpool for service since the product is under warranty. The closest appointment was more than 2 weeks out. On the appointment date the technician called me and said he was on his way to my house which is more than 30 miles from my tenants apartment. The technician said he could not service the tenant area as that was a different group, so we rescheduled for a week later. A week later no one shows up, so I rescheduled yet again for November 3rd and drove myself to wait for the service person who was supposed to be there between 8 am to 12 PM. At 11:40 I saw there was a 10:36 am Whirlpool attempt to call me but no message was left. When I called back they told me the technician called in sick and they called at 7:30 (my iPhone indicated 10:36 am). Now they say someone will come on Saturday November 5th. It will be one month on November 8th with no working washer. While it is bad enough the washer stopped working in less than one year their service support is even worse than the product.

I inherited this microwave when we bought our house and have been very happy with it. It does not take up much space, heats well and evenly and the beep at the end of the cycle is not as irritating as other microwaves I have owned. However, I do find the glass turntable difficult to get back on track after I take it out for cleaning. It will wobble if not put back exactly right.

Four years ago, I purchased a Whirlpool refrigerator - French doors (ice and water in the door) and freezer bottom drawer. Against everyone but the HH Greggs salesmans advice, I purchased the extended warranty as I had paid a large sum of money for the refrigerator. Within a year, I began experiencing problems with the ice maker. Over the next few years, I had to have it repaired/replaced an additional three times. Add to the whole mess the incompetency of the A & E Repairmen that required at least two visits each time to complete a repair and their inability to arrive during a 9 hour window, I stayed livid about my refrigerator for three long years. Finally, I demanded a replacement refrigerator under the lemon portion of my warranty. After numerous arguments, the warranty company offered me several different makes and models to pick to replace my hunk of junk. Stupidly thinking that my problems were related to one bad unit, I selected another Whirlpool only to have it completely crash a little over one year after acquiring it. I lost the food in it and am having to wait almost a month for the parts to arrive and the repairman to return. According to him, it will have to be completely rebuilt. I will never, never buy another Whirlpool!

I bought a top of the line Whirlpool dryer that cost me over $1,000. Havent had it for a month and it requires a service call. Have to wait two weeks for service! Totally unacceptable. The dryer is JUNK and now I am stuck with it. Horrible company. Bought from Home Depot.

I bought a Whirlpool gas range in March of 2015. Three months later the control module went out on it. It was still covered under warranty through Whirlpool, so they send a technician out to fix it. Its now a little over a year later and the control module is out again. I call Whirlpool and ask them if it was still under warranty and if they can it fix it so they say, you want me to send a technician out. Why? I just assumed since theyre sending a technician out but there were going to cover it. Well the technician gets here and its not covered under warranty. And I now I have to pay a $90 service charge fee for the guy to tell me that the control modules out on it which I already knew. Hes going to charge me more than the stove was worth to fix it so I declined to get it fixed.

I called customer service because my pilot light would not stay lit on my 2005 Whirlpool water heater. I was told that I needed to install the upgrade kit and that the water heater was malfunctioning because of a lack of air and that it needed to be cleaned at the bottom. I paid for the shipping of the kit although I believe it is called an upgrade or conversion kit versus a recall for this water heater to save money and to get the consumer to pay for replacing defective parts. A certified technician installed the kit but the pilot light would not remain lit. He replaced the thermocouple, although new parts had just been received. This did not help either. The technician and I called customer service, which didnt resolve the issue. I also asked for a manager who would only agree to send out another conversion kit. There are three years remaining on the warranty but I am being told to keep replacing new parts with new parts until it works. That is unacceptable. Also, I was not informed that my problem is a recurring problem with this Whirlpool water heater that I purchased at Lowes.

Just had the repairman at my house to repair my 2-year-old Whirlpool refrigerator Model GB2F4DXWS07 - he couldnt fix it. Just throw it away and get a new one. There is a blockage somewhere in the line, he suspects the lines were not cleaned before it was charged at the factory. Repairman said it was a typical 20-year-old refrigerator problem. Customer service was no help - Whirlpool live chat is currently unavailable. Lousy product with worse service. I will never buy another Whirlpool product.

I purchased a brand new 2019 Whirlpool side by side refrigerator in October of 2019 for my new house. Yes, that was 2.5 years ago. HOWEVER, I live alone and hardly ever use the ice dispenser. Maybe, it was used 20 times in 2 years. The ice dispenser just stopped working and today I notice the refrigerator is not even making ice! What a piece of garbage!

Purchased Whirlpool Gold appliances for a kitchen reno two years ago. Fridge and stove from a dealer and microwave from Lowes. Fridge - After one year the ice maker quit. $200 part plus labour. Seal on fridge door not sealing. New hinge and washers to adjust. $30 plus labour. Stove - three different stoves were delivered with the same paint flaw on the top of the control panel (3 inch section where paint did not adhere or was scraped off... Same spot on all three... clearly a factory issue). Stove door - when you touch it the interior light goes on. Warming button and switch was broken when purchased but didnt notice. Whirlpool wont warranty. $48 plus labour. Last piece in this puzzle... Microwave - magnetron went and wont heat. $300 plus labour. Obviously time to change brands. Now to figure out who is NOT under the same manufacturing umbrella.

After much frustration and disappointment, as well as 2 huge repair bills with my front loading washing machine I sent it off to the scrap yard, still looking brand new, and went back to a top loading machine. I purchased a Whirlpool top loading, high efficiency, low water machine. I have had it for almost 2 years now and am extremely happy with it. I would highly recommend it. Fairly quiet and easy to use and takes very little detergent. It does not have an agitator so it is gentle on clothes. I know some users have complained about tangled clothes but, in my opinion, if it is loaded correctly this should not be a problem.

Bought brand new stove, had issues from day 1, called them after TWO different repair companies came looked at it and said it was a melon, Whirlpool wanted to send a third repair company. Started dealing with this in September, its now end of December and Im still waiting for replacement stove.

Whirlpool 500galaxy gas water heater - First week ran great. Now Im lighting every day. Called Whirlpool and just getting run around. Had it a month today, still lighting every day. Cant afford to buy another.

Ive spent more repairing this washer than what I paid for it new!!! Its really ridiculous that Whirlpool isnt more responsible for their equipment that doesnt stand up to their name! Ive replaced more things than I want to type but just to start the computer board, pump, bearings just to name a few. Each time I had my repairman out it was a minimum of $300 to repair. Ive had my repairman out 5 times to repair things. Thinking each time its cheaper to fix it than buy another which I surely didnt think I would be repairing it several time! At this point Im just sick to death that a washer that is for a home of myself and my daughter has broken down so much. I cant imagine what a family would go through. Even after all the repairs it still isnt right but Im done sinking money into this sinking ship of a washer! Its loud constantly stops due to un level so I have to move the clothes around usually having to repeat this several times before I can get the load to finish!!! Then they come out wrinkled more than they went in and I have to iron clothes. A person should NOT need to iron! May as well wash them in the river on a rock. It would be easier!!! SO DISAPPOINTED!!!

I used their website to schedule an appointment for an estimate for a repair on my oven. I was never told they were sending an independent contractor to do the repair nor that there would be a charge for the estimate. I contacted Whirlpool and was told there is nothing on their website and I should have asked the service technician before he was at my door if there would be a charge. Therefore, it was my fault and I indeed had to pay the charge when I declined to have my oven repaired. I paid an independent contractor hired by Whirlpool for $129 to give me an estimate on the repair to my oven despite never being told of such a charge prior to the appointment.

Love my new fridge, not in love with the icemaker though. Every couple of days I have to reach in and scoop the ice off the little shelf in the back, or else it will quit making ice. The ice cubes block the arm from coming back down to trigger a refill.

We purchased the Cabrio washer and dryer due to the companys past reputation and our own past experience with Whirlpool appliances fully expecting to receive great performance and durability. We have had the pair just about 2 years and the washer started experiencing problems during the spin cycle. The unit would get out of balance easily and then it would stop without spinning, leaving the clothes very wet. Well, as our past experience had indicated to us the washer is usually much more reliable than the dryer, or thats the way it had been for us. So we only purchased the extended warranty on the dryer. Not being covered on the washer we located a local technician and he promptly diagnosed the problem as the transmission failed causing the noisy bearing and the failure of the unit to spin properly.Our tech quickly repaired the unit but this failure disappointed me to the point of contacting Whirlpool. Thats where I came upon this site and saw the multitude of complainers with the same type of problems and some that are worse than ours. Our purpose in this review is to add to the 1100 or more reviews that report the same kind of issues. We are now in the same mindset as the 1100. Will we ever buy another Whirlpool? Probably not, especially since it doesnt look like Whirlpool wants to stand with their customers to make it right. Customer support is just as important to us as the reliability we seek. I would much rather spend a bit more in the price than replace or repair the unit after the purchase. A little economics lesson for our friends at Whirlpool is that if you abandon your 1100 customers you will save about $440,000.00, but those 1100 will tell everyone they know of their problems with that product and as a result many thousands will never purchase a Whirlpool. So if we all influence 5 of our friends not to buy, then 1100 X 5 = 5500 people X an average price of $800 which equals about 4.4 million dollars of lost sales. Seems like a no brainer to want to stand behind your customers. We dont believe that any washing machine on the market should fail after a few months to 2 years. These products should be built to last many years and the maker of these products should have that goal.

We have had the washer and dryer for over 10 years and they are still working great. We have had washers and dryers in the past within 2 years have failed, and repairs have cost us almost as much as a new one. Thank God for the ones we have now.

I have owned an Accubake gas range since April 2012. The range is 3 months out of warranty, and the oven will not light... just a clicking sound and gas pouring into the oven. I have also had problems with the burners being turned on by brushing against against the knobs. I have a note by the stove to remind myself to check that the knobs are in the OFF position. My 1 year old grandson turned the burner on just by touching the knob... NO SAFETY FEATURES!!! I havent checked to see what a repair is going to cost me, but if it is several hundred dollars, I will just replace this piece of junk. It is very sad that a costly brand new appliance only comes with a one year warranty. I will never ever buy another Whirlpool appliance!!

We have the same complaints about the washer as other reviewers -- have to use deep water wash to get enough water in the tub to clean and rinse soap from clothes and we have to keep the loads small. Dryer thermostat had to be replaced right off the bat. Now on medium heat it just burned patterns into two light-weight polyester fleece items -- the clothes came out with the heat input screen pattern burned into them. Now I wonder if they stuck to the heating screen for any length of time, was it a fire hazard? The burned parts of the items are now stuck to the drum so that needs cleaning. So well be using low heat on most everything and drying them twice, since low heat leaves them pretty wet after 35 minutes. So much for buying energy saving appliances which, by the way, we were proud to buy! But, prior to buying these appliances, we had washer and dryers that last 20 years. Built in obsolescence with these new things? I have no faith in the consumer complaint process anymore. The retailer may care as they are a bit closer to the problem, but the manufacturer? Forget it. Vote with your wallet and dont buy these products.

We bought a WRS325FDAM02 Side by Side Whirlpool Refrigerator and from day 1 we have been having problems with rust buildup on both doors. Bought it in July 2014 and have had the service people over to figure out the problem many times. They finally decided to replace the doors which didnt help because the replacement doors are doing the same thing. We have bought everything they told us to buy to clean and try and prevent the rust from coming back but nothing helps. Our warranty was ready to expire so we bought the extended warranty only to find out that cosmetic issues are not covered under the extended warranty plan... Stay away from this model refrigerator... Not only that we were then told the doors are not really Stainless Steel just some fake crap that looks like Stainless Steel. We paid good money for this refrigerator and have to deal with cleaning rust off the doors day after day.

Apparently the planned obsolescence period for Whirlpool ovens and microwaves is 11 years. Last month, we had to get the oven repaired, and now the microwave has stopped heating. Coincidence??

Bought this 18 cu ft refrigerator this year. Only 3 choices for temp. Everything freezes, milk has crystals, ice cream is soft. Buyers remorse! Old ref was a Whirlpool. Wished I would have given others a chance.

Never again will I buy a Whirlpool product. I paid over $800 for a new washer 51/2 years ago. I had it worked on twice under extended warranty. Now the bearings are out of the tub and it sounds like a jet taking off when it spins. I had whirlpool products in the past and they lasted for years with no problems. I have a friend who has a relative who is an engineer for whirlpool and his job is to engineer their products so they fail within a certain time frame. They dont want them to last like they use to. They now have gotten their product line to the point where they can tell when it will fail. This is crap. What happened to products that lasted like they use to. NEVER BUY WHIRLPOOL.

I have been using this brand for many years. My first washer lasted for 30 years..so I will stick with what I know is reliable. It is a great machine. Very simple. I dont need anything fancy. 3 different cycles to choose from.

I have had this refrigerator for 23 months. The ice maker has been a continual problem. It overfills and water runs onto my hardwood floor. After four service calls for the ice maker, the defroster heater caught on fire and melted the interior wall of the freezer. Not sure if we fixed the ice maker since we had the fire four days after the last service call. My service rep declared the refrigerator unrepairable. Fortunately I had purchased an extended warranty and they refunded 85% of the purchase price after 2 years of use. Besides the ice maker problem and the fire, I also had trouble with food freezing in the refrigerator compartment. I dont recommend this model, but my repairman says that Whirlpool is as good as it gets.

The space could be laid out a little better. The flimsy shelf is not real stable for foods or ice tray. Where the shelf locks into the side wall is not deep enough to stabilize the shelf itself. The flat indentations in the bottom, where they meet the front, have an edge that makes properly cleaning the freezer a bit difficult.

I have had this machine (Indesit IWDE126 Washer/Dryer) for a very short time; the washer is great. It does a 20 minute daily wash which is good however the dryer part screws up everything you put into it and ironing, even with steam, makes no difference at all. The WORST part is the organisation DONT CARE. I wrote to the Chief Executive, Jeff Fettig, who neither acknowledged my complaint or responded to it. I made this complaint in October 2016 and STILL do not know what the outcome is. If you are reading this review I honestly would look elsewhere for a better machine. Try MIELE. They are expensive but 2000% better.

We owned a Whirlpool Duet washer that went out in late December 2011. We bought another Whirlpool Duet washer on January 8, 2012. On July 31, 2012, it stopped working with the error message F24. In WV, Whirlpool contracts their insurance/warranty through ACE Appliance. We scheduled with ACE the next day. They came out on August 6, 2012. The repairman told me it would be 7-10 days for the part. The part was on back-order, so in reality it took 17 days before they returned. It was repaired on August 23, 2012. Today, September 17, 2012, the washer stopped working again with the same error: F24. Whirlpool will do nothing to replace the washer, even though it is less than a year old and we paid $900 for the washer. This is the second Whirlpool we have owned that has crashed. I have two small children (4 and 2) and I am due with number 3 in 3 weeks. While the washer was broken, I spent nearly $80 at the laundromat for washing only - I carried baskets of wet laundry home to dry. And now I get to repeat the same exact struggle less than a month after it was fixed. When asked, the customer service rep told me that no matter how many times it broke, all they would do is send a repairman. They never ever replace appliances regardless of the problem. I am unbelievably frustrated and I want to tell everyone that I possibly can to stay away from Whirlpool appliances! Do not buy them new! Their manufacturers warranty is a joke!

We purchased our Whirlpool Front Loading HE Washing Machine a year and ten months ago from Future Shop, and now it has failed. After paying about $100 for a service call, we were told we need to order a motor control board that will cost an additional $397 plus tax, plus installation. Because it is off warranty, this means my $1030 washing machine that is less than two years old will cost me about $680 to repair! My parents old top loading washing machine still works after 30 years. And now I notice that so many other people have had the exact same problem. Why hasnt Whirlpool fixed this issue? This is criminal! What on earth is going on here? I was under the impression that Whirlpool was a top-notch brand.

My wife and I purchased a new Whirlpool Cabrio Washer / Dryer set approximately three years ago and have had nothing but problem after problem with these units. Weve had multiple service calls, multiple parts replaced, and after dumping hundreds of dollars into repairs and service calls (even called Whirlpool and asked for some help with parts cost but was given the cold shoulder and was told, We cant help you), we are dumping these machines where they belong - scrap heap. I will never purchase another Whirlpool product and will tell anyone who will listen what garbage Whirlpool manufacturers are and absolutely pathetic excuse for customer service and the poorest of quality product. Whirlpool will never be in my familys home again and will never see another cent of my monies.

It was not a good experience after I purchased a Whirlpool washer in Feb 2014. I have been going to Laundromat 5 months since I found the door did not able to secure. I reported in January 2015 and technicians from 3 different contractors made more than 10 visits for checking and replacing parts. Not only nothing gets done, I also missed work for all these days. Then I escalated to the Supervisor, ** and Miss ** in Executive Office of North American Region. Both of them are very nice that they understand the situation and how frustrate it is. Finally, ** said Whirlpool would replace it. ** told me that I should get phone call from H.H. Gregg within 48 hours. However, it has been two weeks and seems no one care. In this three days memorial weekend, I still need to go to Laundromat while they are enjoying BBQ with their friends and families. I dont know how long it take to replace it.

I have had the washer for 3 years now and it started to make a loud noise during spin cycle. I made a service call and found out the bearings are damaged. Something that cost this much money should last a lot longer. I have researched on the internet and found this to be the problem for a lot of consumers and would like to see something happen.

Bought new from menards. Doesnt work properly, doesnt wash right and cleans poorly. It too bad because I thought I was upgrading from my old Whirlpool washer that was 15 years old so I order the new cogs for the agitator on the old machine and now using it again. Works better than the new one. Sad that whirlpool wont stand behind the product. Might as well be made in china.

The oven will not turn off. When I called Whirlpool and told them what had happened they immediately put me in contact with the safety division. My question is if it is a safety issue, why is there not a recall and why do I have to pay for the circuit board. If there is a safety issue why is there not a recall.

Ive had this microwave for about a year and a half. Like some others I get the door sign frequently. I open the door and cant turn it on until the light goes on, which can take a minute to two. I have NEVER had problems with any microwave other than this one. I had a problem with the Whirlpool refrigerator too, which was fortunately still under warranty. I bought the fridge, oven and microwave as a deal. Trust me, there is no deal here. I will never buy this brand again. Lesson learned. Given other reviews, I might just buy another brand of microwave. Worth not having the hassle.

I have not had any issues with my washing machine yet as I have only had it for two and a half years. The features the machine offers are good and there are many options. So far the washing machine has worked as advertised / expected.

Over-the-range microwave hood combo - It is not that it does not work, it just wont shut off! Close the door, it turns on. Touch the side, it turns on. I have walked in the kitchen and found it on! I am afraid it will turn on when I am not home and burn down my house! After reading the poor customer service received by others, I will just replace it.

When I purchased my Cabrio washer 31/2 years ago I didnt bother to check reviews since Whirlpool was suppose to be the best of the best. An expensive lesson! A washer that spits out codes?!?! Whos got time for this? We paid 899.00 plus taxes for it, now we paid a repairman 99.00 to tell us its not worth fixing. He said the bearings were completely shot. As he was leaving he said his next service call was for the same type of washer! Whatever happened to appliances that last! Going green is all the rage but yet everything from cars to appliances is built to last only a short while. Judging by these reviews I cant believe Whirlpool didnt recall their garbage!

I bought the HE Whirlpool Cabrio 2 years ago. It has all the bells and whistles, fancy cycles, etc. but doesnt clean ANYTHING. I have to wash three times to get things clean... So much for energy efficiency. It also gets out of balance with larger loads. What a waste of money and time.

I cant believe the list of people here with poor quality of their washing Machine. My first problem was covered under warranty. I have paid for two service visits from A&E and now every 5 minutes get the LF error. My fabric softener does not drain into load either. My only option is repair again and I got a sorry from Whirlpool. I think Im going to look for an old fashion cheap machine as it cant be of worse quality than this Cabrio wtw6400sw1.

My dishwasher was only 18 months old when the rack adjuster broke causing the top rack to collapse. I researched and was able to order the replacement part which now comes only in metal. (The original Whirlpool piece was cheap plastic.) I spent $40 for the new part and spent several hours installing it without any help from Whirlpool. Then when I tried to use my dishwasher it wouldn’t run. Repair person came out and diagnosed it with a pump assembly failure. Part alone was $222 and it was on back order. Extremely disappointed. I have tried to contact Whirlpool to see if they would at least offer me a discount on the part. Their customer service number is never available. On hold for so long I finally gave up. Maybe I just got a lemon but I will not go with any Whirlpool product again.

From the very beginning the washing machine did not clean the load. It doesnt even get the load completely wet. The best you can hope for is to utilize lots of fabric softeners to at the least make your clothes smell clean because they surely wont be. Dont even get me started on the load lock feature because it serves no purpose other than to drive you batty. When your 15 year old son offers to give you money to buy a new washer after owning the one you just bought there is nothing I could say more profound than that. How Whirlpool stays in business befuddles the mind.

I bought my glass top stainless electric Whirlpool range in April of 2019. It worked great until December 2019. Four days before Christmas my daughter was home alone and using the oven to heat up dinner. She smelled a terrible smell and there was a ton of electrical blue smoke. She called me at work and I told her to turn it off. My husband came home as I was talking to her and pulled out the stove. The place where the stove meets to cord had burst into flames. The wires in the cord were so badly damaged they were all exposed and singed. Our house could have caught fire! The whirlpool company will not stand by their product. They blamed it on the team at Lowe’s who installed the range...Lowe’s has been nothing but confusing and frustrating to deal with! I can’t believe how we’ve been treated. Do not buy whirlpool! These stoves are dangerous!

I purchased Duet washer 3 years ago, but it wasnt installed until a little over a year and a half ago. Machine started making loud noise during spin cycle, and eventually would not spin the water out of the machine. I contacted Whirlpool and was told there was a defect in that particular WP model and if it was confirmed by a provided tech, WP would provide the parts for the repair. The tech confirmed the problem, and I was told the repair would still cost over $450, even with the free parts. When I approached WP and asked them to fix the machine since it was a known defect, it was denied that there was a defect.

We purchased a Whirlpool Cabrio Platinum washer and dryer from HH Gregg and have had continuous issues with the washer. We have had the lid springs replaced two times since we purchased it and they are out again. I called our service company to ask why we have to continue to replace the springs very 6 months and they said it was a problem Whirlpool was having with this unit. I called Whirlpool and after being on the phone for 45 minutes, they told me there was not a recall, but I could buy the parts directly from them for 1/2 price. This amounts to about $20. The repair cost me about $200 every 6 months because it is a difficult installation. Whirlpool is a terrible company to deal with when you have a problem and they do not stand behind their products. I will never buy another Whirlpool product and will tell everyone I know the same.

My Whirlpool Cabrio WTW7800 was bought 1 and 1/2 years ago. The lid is glass with a plastic edge. The plastic part of the lid next to the glass and hinge is cracking causing the glass to stick up. It is cracked from the top of the lid toward the base if the lid were closed. The only way this could happen if it werent a manufacturer defect would be if someone were to get inside of the washer with the lid locked and try to push up to get out right at the hinges. I have noticed several other complaints of the same problem on this website with the same model. Clearly this is a manufacturer defect. I am on the phone with Whirlpool now.

Everything Whirlpool that I buy is junk these days! Whirlpool used to be one of the best brands, now, cheap China GARBAGE! My dishwasher will not fill enough to clean the dishes without setting it on pots and pans. Then it runs for hours and uses a ton of electricity! I tested the water fill cut off, after it fills it is not even close to lifting it and the switch works fine. I returned the Whirlpool dehumidifier I bought recently, it was junk as well!

We bought a new Whirlpool refrigerator about three years ago. Because of space, we had to purchase one with a top freezer and also with no ice maker. First of all we didnt realize it was much deeper than our old Kenmore so it stuck out further into the kitchen space. That was not that big of an issue. At first everything ran great including the top freezer compartment, or so we thought. Then we noticed that when we had ice cream in the freezer and put water in ice cube trays to freeze, the ice cream would get very very soft. This continued to the point that now anytime I put water in there to freeze ice cubes I have to turn up the temperature to keep the ice cream frozen. Once the ice cubes are froze, there is no problem, but they take at least six hours to freeze. Then one day when a young child slammed the refrigerator door closed, the freezer door popped open about an eighth of an inch and then closed again. So, I tried it. Anytime you close the refrigerator door a little too hard the freezer door pops open. I then tried the dollar bill test to check the strength of the seal. The bill pulled right out of the door with very little effort. So, is the problem bad seals, bad design, or bad quality control, or what. How can I be assured that the frozen foods in the freezer are being frozen as solid as they should be. I know they dont freeze solid enough in the freezer door. I will eventually dump this refrigerator and go get another Frigidaire. If we have to get one with a bottom freezer, we will just have to rearrange our kitchen to accommodate it. But, having to turn the temp up and down every day is ridiculous. I have had issues with food close to the walls in all refrigerators slightly freeze, but never had an issue with keeping things cold enough. I will never buy another Whirlpool refrigerator, stove, or anything else for that matter. I have always had good luck with Frigidaire, so I will stick with what I know works.

My Whirlpool microwave heating plate is not rotating properly.

I purchased new and installed my heater in 2003. SN: 0253109845, MN: EE3J50RD0454. I started removing and replacing or cleaning heating elements in 2011: pretty good service. In 2015 I noticed black and brown water coming from the hot water taps. I opened it again, cleaned it, and realized anode replacement was required. That is when trouble started.I tried everything usual including 4 foot cheater bar, heating the coupling, impact wrench, tapping with a hammer, etc. Finally found a 700 ft-lb. pneumatic impact wrench on sale at Harbor Freight. After serious wear and tear on my air compressor and about 1-1/2 hours of work with the impact wrench, I got it out. The threads were messed up some, but I did not look close. I had to put the 1-1/4 inch head back in to return it to service while I found and ordered an anode. Could not get one from Whirlpool and could not buy one in Lowes where I bought the heater.The surprise was when I cleaned the threads to put the head back in, I had to use almost as much time and torque to get it to stop leaking as I did when I took it out. Then, when I did try to install the new anode, it required to same effort. Conclusion, There was some kind of imperfection with the threads in the coupling that messed up the threads on the initial installation of the anode, which made it nearly impossible to remove. Whirlpools quality control stinks. The next one will NOT be Whirlpool.

Wish I had done more homework before I purchased a Cabrio washer and dryer. The washer uses so little water that I sometimes find dry spots on clothing when I take it out. How can it possibly be clean if it doesnt even get entirely wet? I now pre-rinse all of my underwear before putting it in the machine. I know the instructions say not to put in wet clothing, but if it breaks sooner, Ill get to replace it sooner with a more traditional model. I always use the lowest spin speed - anything else makes my clothes hopelessly wrinkled. I like the large tub for washing blankets and comforters. Thats about the only advantage I can think of. The dryer sensor quite often goes off after about 2 minutes if I use any setting other than the delicate or timed features. Ive had the machines for 2 years and had the dryer repaired once under the extended warranty I purchased. Very disappointing purchase.

Regarding a Whirlpool Refrigerator (model ET8CHMXKQ04) purchased in 05. I dont remember exactly when the problem began but the freezer starts its defrost cycle, water drips down through the refrigerator compartment (soaking all paper/cardboard covered products), collects under the crisper trays and eventually spills out onto the floor. Its a river of water that requires a towel to collect.I believe whats missing is some sort of collection funnel and tube that catches this dripping water and delivers it to the evaporation tray behind the base cover plate under the refrigerator. Obviously, Whirlpool has no quality control nor does it do any field tests to ensure their products are designed and operate properly.

On July 19, I was forced to buy a new washer. Bought a Frigidaire which, when connected to the water supply, started immediately dumping water into the drum. Sent this defective washer back to the retailer and chose a new Whirlpool. O-M-I-G-O-S-H! It was delivered on 25 July and despite having 4 temperature settings, it only worked on either hot or cold AND you could never tell what temperature was going to be chosen by this computerized wonder. I repeatedly called Customer Support and received three different answers on what temperature was considered warm. The answers ranged from 65 to 102 degrees. Also, you could open the lid when the water was running in, which washers are no longer supposed to do. Whirlpool then arranged for A & D Service to come and repair my NEW washer and scheduled an appointment for a week later. I was forced to call that company to find out if they were even coming. When they did not show as promised, I cancelled the appointment and called Whirlpool to ask for another service company. They then scheduled me for two weeks later (now August 30th). The guy did come and told me there was user error - I had used too much soap as this was an HE washer. I asked him to show me where on the appliance and in the owners manual that it stated the washer was an HE. He couldnt find it either and said he would replace the computer and the door lock because his computer found that the washer was hit and miss on anything it was set on. At any rate, it is a little over a week later and I have heard nothing from the repairman and, of course, no follow-up from Whirlpool. Do not make the mistake of buying any Whirlpool product, and that now encompasses names such as Maytag, Amana, Jenn-Air, Kitchen-Aid and many more if you want to be assured of a quality product and excellent customer service. What if this had been a refrigerator? The whole debacle has been a nightmare. Wish I had bought a GE!

I purchased the top-of-the-line Whirlpool Cabrio washer and dryer. My washer is 6 years old and will not complete a wash cycle. According to the repairman, the drive shaft is stuck and it will cost $500.00 to repair it. When speaking with Whirlpool, their suggestion was to buy a new one and get an extended warranty. This company is a total disappointment.

I have a combo Microwave oven/oven GMC275PDS07. When the microwave is finished with the requested program, the end of program chime lets you know its done. Then, if the door is not opened for at least 3 seconds, the chime will ring again every minute thereafter ad nauseum. This will go on for hours without end. I know because I tried it. I reached out to Whirlpool via a web chat and my question was not even addressed. I was ignored. From reading other submissions, I assume this is de rigueur for Whirlpool. I then called Whirlpool and spoke to Katie in Tennessee. She was not able to bring up any make or model when I provided her the numbers exactly as listed on the inside of the door. She was not able to provide any respite from this annoying feature.This a Whirlpool Gold model, presumably the top of the line, in my book I will never purchase any Whirlpool product of any type and I will make it a point to let anyone who will listen that Whirlpool is not a manufacturer that takes its customers concerns seriously. Katie then advised that she looked up this feature and told me there is no way to turn the beeping off. I find this amusing since she could not find the model or serial number when I gave it to her.

I hope the CEO posts this on a giant screen in front of all their employees. The first thing I did after moving into our new home is brag about the American made Whirlpool appliances. Being from the Midwest I take pride in made in the USA product and go out of my way to support homegrown companies. I know that a number of the components in my fridge include the fan that failed after 11 month were most likely sourced and manufactured in China... but that no excuse!! Whirlpool needs to do a better job of QC. You need to be passionate and rigorous with your testing. Dont reduce cost at the cost of your customer base. It is amazing were to the point where we can no longer compete with China in quality.Second is customer service, if you know you cant compete in quality you need to be able to make up for that with customer support. I called Whirlpool and scheduled an appointment the day the fridge quit working. I was upset that it would take three days to have a working fridge but I was understanding. Lucky for me I had an understanding neighbor too. Anyways, when the day came for my scheduled warranty repair I was told that Whirlpool was mistaken and that I wouldnt be able to get it serviced for another week! This is just unacceptable.Right away I called the Whirlpool customer service representative and manager to express my frustration with this error. They were polite and both agreed with my frustration. It also sounded as if they also didnt understand why their own company was doing such a poor job addressing repair issues. They made it sound like this was a common problem of people getting overbook at repair service providers. Again another fumble. Bottom line, due to my position, I dont really have a choice but to wait another week for a repair. Take note: Every time you lose a customer like me this you lose 10! I will now go out of my way to tell people about my negative experience rather than my positive. So disappointed.

My 1 1/2 yr old refrigerators cooling unit quit and I have been so disappointed with A and E appliance the only warranty service provider for Whirlpool in the state. From first call it took 10 days to service - then told no part - then 2 weeks for part to arrive and service done. 3 + weeks is unacceptable. Lowes tried to help - but said Whirlpool had to authorize a replacement in time for a 3 generation family reunion. Whirlpool was to call A and E to see if they could expedite and Whirlpool never called me back. I will try again on Monday - but my frustration with A and E and Whirlpool prompts me to write this negative review and I am not a negative person!

The oven is a joke. It does not self-clean. I have to buy oven cleaner and clean the oven like in the distant past. They are lying about it being self-cleaning. Do yourself a favor and buy a real self-cleaning oven. NEVER WHIRLPOOL.

We purchased our 4 French door refrigerator in November 2014. It started making a loud noise, like an air compressor about a month ago. So loud that when we are watching TV in the bedroom we have to close the door! It continued to get louder and more frequent so I called Sears. It is under warranty so they sent a repairman out. When he came, he said it was because we had the refrigerator too cold & it was causing ice to be stuck around the fan??? We had it at 5 and the coldest is 7... He suggested we put it on 3. 2 days later and it is making the same noise again. Will be calling Sears again. I saw a similar review saying the same thing!!!! This is a five month old refrigerator! Very disappointed in product and service.

My 4-year old water heater has upper/lower sensor issues for the fourth time this year. The rep was supposed to send replacement parts to arrive today (day four with no hot water), but the wrong ones were shipped. A different rep called and offered to exchange the unit for a new one. The expense to me will be $350-$450 for the plumber to uninstall my unit, take it to Lowes and bring the new one back to install. The plumber suggested I take my $450 and just buy a new non-Whirlpool unit. He knew immediately that I had a Whirlpool hot water heater because its the most common repaired vendor. Whirlpool should be covering this expense for re-installation of their inferior product. Poor customer service. Day 4 with no hot water during the holidays with no solution in sight short of me purchasing a new hot water heater. Whirlpool finally got the right parts to me and I paid a plumber $190 to install. One week to the day later, my pilot light will not stay lit. No change in ventilation since it has been installed. I will say I have been dealing with their rep Chris on the phone who is extremely nice and I feel sorry for him. But we all have the exact same issue which is not being resolved.

I purchased a Whirlpool washer (WTW4800Q) in November 2011. Already, it has rust in the tub. The warranty does not cover this. I never really liked the thing since I have had it. It takes much too long. Lid locks and then starts over. Also, warranty is not good. I wouldnt ever buy their product again and suggest no one else should either. I loved Maytag before Whirlpool bought them out. Im putting this one on Craigslist and buying a real washer, a Speed Queen! Yes, Speed Queen has all metal parts and makes a home washer. Just have to find a local dealer. They are there.

Purchased from Home Depot and self-installed. That part was not too big a deal but after installing this stove we started a journey of irritation, aggravation and general dissatisfaction. This stove has the standard layout for burners that seem to be common to most low-end stoves. Two huge burners in the front, a simmer burner at the right rear and a general purpose burner at the left rear. Thats all wrong for me and our set up. I want a large burner at the left rear and general purpose every place else. Can you alter the standard configuration? NO! Not without some major alterations to the stove top.Next are the grills or cast cooktops (2 each). They are a bit cumbersome when cleaning the stove but doable. The real problem with the grills are Whirlpool decided to save money by skimping on this feature. The grills are not a stable cooking platform for smaller pans and it turns out Whirlpool recommends square pans for this stove. SAY WHAT? I have pans and skillets from my grandparents and they are ALL round. Thats how that stuff is made. ROUND! The grills design is unstable for any round pot, pan or skillet, if its diameter, is 6 or less. Kiss that excellent saucepan goodbye if you have this stove. My current solution is a piece of light expanded steel over the burner areas.Keeping in mind we use Propane as our heating gas. The adjustment of the flame temp on the four burners is non-existent. They all are either on high, medium or low. There seems to be no fine tuning with these burners. At the end of the day go look for something that is NOT a Whirlpool, LP gas range Model #: WFG515S0EW. You will be better served and less irritable with almost anything else. Even a campfire in the yard is a better choice.

Purchased WRF989SDAM00 French Door refrigerator in 2013, and 33 months later it is not cooling (fridge 45/freezer 36 degrees). Service call diagnosis is a leak in the sealed component area. Since it out of the 1 year warranty period, nothing is covered. This is the first of Whirlpools dual evaporator models, and is technically challenging according to the service technician. Most likely one or both evaporators are defective, and this type of failure comes with a recommendation to change out the compressor as well as it is moisture compromised.As my previous Kitchen Aids had 10 year sealed component warranties, and the Whirlpool is the same base mechanism as the Kitchen Aid, I contacted Whirlpool to see if they would extend my warranty coverage to these sealed components. Website submission - never got an answer. Called the customer service line - they politely told me they were sorry but there is nothing they can offer me. Even the extended service plan would not cover me as this refrigerator has a preexisting problem and it must be 100% operational to begin an extended service contract.Im extremely disappointed in this fridge only lasting 33 months, in comparison to my previous Whirlpool/Kitchen Aid refrigerators. Of course the internet just allows me to see that Im not alone is purchasing a short lived appliance. So here is my contribution to the internet of things: Do not purchase Whirlpool refrigerators expecting them to last much beyond the warranty period. Buyer beware.

I knew I couldnt be the only one with these problems. The reviews confirmed it. I bought my Cabrio washer in 2012. Energy efficient, no agitator to catch on clothes, Great. It took me a while to figure out that the machine was eating my clothes and not cleaning them at all. Oh, they smelled fresh. That HE detergent smells nasty. The machine ate the edges off my good towels, T-shirts, jeans. Brand new underwear (thick elastic) was stretched all the way out and pulled. Normal stains and dirt do not come out even with pretreating. I started running my clothes on the delicate cycle, prewashing stains in a bucket by hand and then putting clothes in mesh bag before running the load. They still came out dirty and ruined. When I run the loads, it still registers as not being that energy efficient on the controls. Id gladly trade it back for my old washer. I feel like I have stepped back in time to a time where you washed everything in a tub or bucket. What a waste of time.

We purchased the Whirlpool Cabrio washer and Dryer May 2017. First, this washer is SO LOUD! Honestly, NEVER had a washer that is this loud on the spin cycle. My second issue is, that when I wash my blacks, they have white splotches streaks on them. I use ALL clear and free liquid washer and Downy softener, so I stopped the softener, and still the white streaking. Ive since will use the additional rinse on during the wash, but still leaves white streaks. After 3 separate rinse cycles, no streaking. This leaves me thinking that with the lighter colored clothing, there is probably streaking as well, just can see it - my conclusion is that the clothes arent getting cleaned properly, or rinsed. Another issue is the dryer. First, takes longer than all my previous dryers, even the set 110 mins for towels on high, still takes longer. My washers are not packed tight with clothes either - its just my husband and myself - not a lot of washing. Also, I noticed a crack in the inside dryer/drum where it looks like the paint is chipping and cracked. I used some high heat touch up paint, and it did not help. Needless to say, what I thought was an good reputable product, turns out to be, not so good.

Purchased gas water heater from Lowes in 2012. Had no problems until July 2018. Its under warranty but have had to replace the control valve completely and the burner 5 times and it still is not fixed. Dont waste your money. Buy something else.

Everything I buy from this company breaks all the time. I purchased these brands hoping they were good but apparently not. Always have to get them serviced. Lately they did an exchange on my fridge. Hope it helps because after thousands of dollars of food in the garbage it better work. And the washer thought, Oh Im paying more. It will be good. At this point will cost me less to buy from another company. Buyers beware. Cause the company cant do nothing good for me so dont buy from them.

On May 25, 2008, I bought a Whirpool Model# BFG1J4040T3NOV 40 gallon natural gas hot water tank. The pilot light went out today, Sept. 26, 2011, and it will not re-light. This was bought at Lowes and was rated as a 12-year warranty on the tank and parts. This is premature failure of a product that is listed as 12 years. Due to all the other similar complaints of this Whirlpool hot water tank, I would like my money back ($455.81) plus installation or a new tank installed.

Purchased brand new washer & dryer that was chosen specifically for its HE & washing capabilities as Im a single mom with 5 kids, 2 of whom have disabilities, & I need a good washer & dryer. Washer and dryer both broke several times. I paid for an extended warranty but they never resolved the issue. Called Whirlpool & they didnt care. Four years later, Im using a set I bought used that rips my clothes while the washer & dryer sit still broken. Will never buy from Whirlpool or Kettles again.

My front load washer doesn’t get my clothes clean. I have to rinse twice and still there is soap in my towels and they smell bad. I’ve followed all the tips without much luck. Now I use only Oxyclean and rinse with 1/4-1/8 c vinegar. The machine doesn’t pump all of the water out of the machine either. To me it is low-efficiency!

BEWARE THE TEMP CAN BE 25 degrees off high and 25 deg lower and Whirlpool says that is within specifications. My oven temp was set at 350 and nothing was cooked... After 7 repair calls with their certified repair companies (the 2 worst repair companies that I have ever used) I was told that if you set your oven at 350 that if it stays in between 325 and 375 that Whirlpool claims that it is working fine and will not do anything. I called and talked to customer service and asked the lady that if you set your oven at 350 should it stay within a few degrees of that and she said YES.The people that work at Whirlpool do not even know what kind of junk that their company is selling. I asked to return it and get a more expensive model hoping that it would work better but they said that they sell ovens and do not buy them. Be sure to get in writing from your sales person that your oven will constantly hold the temp within a few degrees. I tried to do the Whirlpool survey but after 11 attempts they said that there was errors in receiving and they did not get it. If you buy Whirlpool then you did not ask the right questions. I WILL NEVER BUY Whirlpool again (unfortunately I have a Whirlpool dishwasher and refrigerator that are not much better) and if you do you will say the same things and be out Thousands like I am.

I will keep this brief because many of our issues on our 18-month-old washer are in other reviews. The anger I feel towards Whirlpool Customer Service and the logic they use in providing repairs on a “goodwill” basis are unbelievable. After a Whirlpool certified appliance repair person diagnosed our fairly new washer as requiring the entire guts to be replaced... transmission, bucket, etc., we were told the repair bill would be over $1,300! Are you kidding me... the washer only cost in the mid $500 range, and now Whirlpool is going to do us a big favor and cover that outrageous bill! I told the customer service supervisor to please give us a new washer and take away our broken washer and use it for parts (if there any good parts left in this miserable machine). His reply “thats not going to happen”. He used this phrase to us at least 20 times during our service call until I finally told him I thought his attitude was aggressive and demeaning. I refuse to be bullied by a major manufacturer for a substandard product.I can only warn you when considering Whirlpool (and every major appliance in our two homes are Whirlpool) that you should use due diligence in your selection. We paid extra to upgrade all our Whirlpool appliances in our homes and I will never make that mistake again. And don’t get me started on the white film that covers my dark clothes. They say I use too much detergent... not true. I am not stupid and understand the HE requirement to cut way back on soap.

We moved into a new home (brand new construction) in Dec 2018. The ice maker/water dispenser has never worked. Weve had 2 different repair people come a total of 5 times to no avail. Now have to deal with Whirlpool directly to deal with Warranty. Will Whirlpool offer a new fridge? No, they will send a replacement door. 8 months later and we still have a fridge that does not work. Not impressed with Whirlpool and extremely unsatisfied with the produce. Do not buy this brand.

I bought this fridge 2 years ago. I had multiple repairs already. Now the side panel makes noise when you shut the door. Repairman told me it is the foam separating from the side panel. There is nothing that can be done. I also have extended warranty.

Whirlpool Cabrio Washer model # WTW6800WW1. Bought it July 2009 and it broke Jan 2017... 7.5 years old. Cost to repair $715.00. The technician recommended that I just go ahead and buy a new one... not worth the while to fix. I paid $900 for this machine in 2009. This is an expensive machine, not a cheap ass one. Shame on Whirlpool for selling products that dont last and for making it unaffordable to fix.

Purchased a Whirlpool Cabrio Washer 5 years ago because our other washer died after coming home from vacation. Its just 2 people in this household so I dont do mountains of laundry. The other machine lasted 15 years so go figure. We purchased the Cabrio from Lowes. Got the extended warranty but as it goes the machine fails when all warranties expires. Over the last couple of weeks this machine started to not complete a wash cycle. All lights go off except for spin light and machine stops. Even asked the person in charge of washers and dryers at Lowes about this who then told me to get an extension cord and plug it into a different outlet. Seriously! I have had to unplug the machine after it fails to complete cycle, wait 5 minutes or so, plug it back in, select rinse and spin, it fails again 13 minutes left in cycle, unplug again, plug it back in, select drain and spin, wait for it to MAYBE complete that cycle. Do not purchase this type of machine. Just for a technician to come look at it is $100 or more and to replace whatever circuit board is probably another $300 or more. Screw that! Going to find a good old fashion one if possible. Piece of junk. Not going to spend $700 or $1000 just to wash clothes for 2 people.

Purchased Whirlpool side by side June 2010. Within a few months realized major problem with ice maker. Reservoir on door would leak and freeze inside the door. Service man out at least twice, advised to maintain service contract as would continue to have issues. It still leaks, freezes up and does not dispense properly. Now the inside liner of the refrigerator is cracking and neither the warranty company nor the WHIRLPOOL Manufacture Co. will stand by their product. It is my intent to warn as many people as possible, so they will not have the same bad experiences.

The washer (Cabrio WTW7800XWO) was less than 2 years old and we had a motor go out, so we paid a repairman to come out and repair the machine. The total cost was over $300. Now 2 months later, we get another code on the machine and Whirlpool says, We are sorry but there is nothing we can do, but if you would like to pay $219, we can get a repairman out there to check out the machine and repair it. Theyre also giving the machine an additional year warranty. Shortly after that, I noticed the lid was not staying up when I opened to put clothes in it to wash. So since I was wondering what was happening, I looked at the lid and to my surprise, the springs that hold the door up when open are built into the plastic lid cover that has a see-through glass on it. Right where the springs are located, it must be a stress point and the plastic lid has since cracked and is almost about to break off. I am now in the process of ordering another lid and Whirlpool offered to sell me a lid for $226 but I think I shall buy it from someone else as I dont want to put any more money into Whirlpools pockets. We paid over $1000 when we bought this machine. Now it is about 2.5 years old. I hope there is a class action lawsuit on Whirlpool as I will definitely join in if there is. This company needs to go out of business if they continue to sell machines like this that have so many problems especially when they are less than 2.5 years old. Goodbye Whirlpool. You have lost many more customers as I shall be letting everyone I know about all the problems and complaints about this machine.

I purchased a Gas Stove from Home Depot on 11/23 and it was delivered on December 3rd. My God, Im having a dinner party tonight and the stove doesnt heat up past 170.. Unbelievable!! Need a replacement gas range. Tried to chat and call Whirlpool unsuccessfully. I am very one disappointed customer right now!

I am 72 years old and this Whirlpool Energy Star HE Washing Machine is just useless. It does not clean clothes properly. It always leaves a stinky washing machine smell which never goes away despite no matter what you do. A completely useless, faulty washing machine! Never ever buy a Whirlpool HE washing machine! Some websites say that you need to buy a washer fan at a cost of $69.99 and attach it to the back of your washing machine as this is the only way you can get rid of the smell. Who has that kind of money? Why is this fan not already included in this washing machine if Whirlpool is aware of the smelly washing machine/smelly clothes problem? This is such a joke! We would like to be reimbursed for our deficient Whirlpool Washing Machine or at the very least, have a recall of this inefficient, poorly designed washing machine. Report them to the Better Business Bureau and anyone else you think can resolve this problem - thanks!! - Unhappy camper

We bought a new stove from Lowes in 2015 which is a Whirlpool with an AquaLift self-cleaning function. This function is totally useless. We have tried it several times and it does not remove the grime from the oven. We did not even have a very dirty oven. It doesnt clean the sides at all and the bottom is still dirty. I complained to the store and they told me the AquaLift function should be used every time the oven has been used. They recommend that I use a spray for the oven (which is porcelain) and scrub off the dirt. Give me back my old self-cleaning oven with the high heat. This new technology doesnt work.

I purchased a Whirlpool dishwasher and refrigerator/freezer from Home Depot. Within weeks the stainless steel on both products began rusting. They sent a third party repair service to look at both products and determined that, in fact, the stainless steel was rusting. Our technician said that both the dishwasher panes and the freezer doors would be ordered and replaced the following week. This was on September 4, 2015. After several promised arrival dates, the parts never arrived. I called both the third party repair company and Whirlpool on several occasions only to be told they were on back order. Finally, in late November, the new dishwasher panel arrived and was installed. It is now December 17, 2015 and our freezer door is still on back order. When asked what my options are, the Whirlpool representative simply said we have to wait. I said that because I have been so terribly inconvenienced that they should just come and pick up this piece of junk and replace it with a new one. Evidently, that is not an option. I will NEVER purchase a Whirlpool product again as they do not back their warranty. I now have a $2,000 rusted refrigerator freezer to adorn our beautiful Christmas kitchen. Thanks, Whirlpool. Youve certainly made this a Merry Christmas. (Yes, sarcasm in play.)

Ive had the stove a long time with no issues. The self clean doesnt really clean of course. In my experience, I dont think many do clean well. Maybe there are newer ones that do work better. I would probably buy Whirlpool again.

My refrigerator is about 7 years old. Has performed great. Good use of room inside. Easy to clean. Bought only Whirlpool products for years however since the last purchase of a range a couple years ago the quality was greatly diminished. May be changing brands now.

Note that most of the complaints are about gas water heaters, but the electric water heaters dont seem to be much better. Mine, barely made 4 yrs old and both elements and thermostat went. Had plumbers in for estimates in to repair - much cheaper to install a new one (No...not a Whirlpool!). Very disappointed in the product.

I purchased the model WDF530PAYM0 serial: F14106104 dishwasher. The foremost reason I purchased this was it had nylon racks. I have discovered that the racks are rusting! It is rusting on the ends where nothing can touch it. I am very disappointed that it is advertised having nylon racks and now it is rusting and deteriorating. This dishwasher states racks-nylon, not racks-nylon coated. I just took some pictures of the racks. I decided to look underneath the top rack where the upper spray arm is located. Now I am plain sick! Most of the underneath is rusting. This dishwasher was purchased and installed 2 years ago. I paid $600 and you would assume that something mechanical would quit after years of use on an average of 1 to 2 times per weeks. Not this one...rusting racks and hard telling what damage the rust flaking off during running is causing to the mechanical components. Lesson learned: Their definition of nylon and nylon coated has no difference.....I very much disagree!

After 3 short years, my dryer that cost me over $900 is not working and the part needed for the repair is no longer being manufactured. They did offer the parts for free, but that was useless since they arent available. They then offered me a new dryer which would cost me $800. I am currently waiting for the Product Exchange Team to contact me. Im not hopeful that will be of any use.