Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

Washer, barely 6 months old, purchased at Lowes. While my washer cleans and I am happy with it, my washer started making loud noises during the spin cycle. I called Lowes warranty service approx 9/26/13; tech scheduled for 10/8, over a week later. Diagnosis: stripped bearings; total bearings and all tub components must be replaced. Parts ordered to be delivered to my door. Cost of washer: approx $800. Cost of parts: over $1600. Washer cannot be replaced until they have attempted to fix it at least 3 times. Repairman returns on 10/18 to repair. Oops, large plastic tub component shipped broken from manufacturer. Reorder parts for repair on 10/29. Finally a repair BUT A&E left the large tub part saying they had no room to take the part. So now Lowes is trying to arrange to dispose of the huge part sitting in my home. I live in a condo so the part cannot be disposed of in our facility. This has been a nightmare to fix and while customer service was cordial, they were totally unable to provide what is considered excellent customer service. So whose fault is it? I have missed several hours of work to try to get this taken care of. I spent money visiting a laundromat for over a month. I am the customer and guess what that means? Nothing! Now my concern is getting that large part out of my home and whether to buy an extended warranty OR just throw it out if it breaks. Very dissatisfied customer! And no the warranty for this major part overhaul is not a year from installation..... my warranty still starts the day of purchase. Are you serious? My advice: ask your friends about their appliances & esp service if they received it.

Weve had this washing machine only a few years, and our household of 2 probably averages 1 load of laundry per week. Weve always had the same problem everyone has with the detergent stains on clothing and having to rewash loads, and the only remedy weve found was using the oversized loads setting and rewashing a load. The last straw was 6 months ago. It quit going through a complete cycle and would not spin out without resetting it. Then it quit spinning out at all. Service Guard, a 3rd party warranty company, diagnosed a faulty motor and ordered a replacement. After a long delay Whirlpool advised it was back-ordered for 3 months. A week ago Whirlpool advised them it was now back-ordered until 5-27. They did not know whether wed ever obtain a replacement motor. After taking clothes to our sons house for a couple months to wash, we purchased another used machine to use until ours is repaired. It is beginning to appear that machine may be our permanent machine. This is a pretty sad testimonial about whirlpool. We have always used Whirlpool appliances but appears we may have to switch brands. And it certainly does appear these low water machines are garbage. Very disappointed in Whirlpool.

Whirlpool gas range model WDF560SAFT bisque color, purchased in June 2020 from Home Depot online. After a 3.5 month wait range was delivered September 12, 2020 and installed. Have used the oven less than 5 times. Standing in my kitchen yesterday and heard a pinging noise, noticed chips of the finish all over my floor, it was chipping inside the top of the oven door, overnight the exterior top of the door was also chipping, bits of finish flying all over my kitchen! Have been on hold with Home a depot Cust. Serv. for almost 60 min. Will attempt to return to a Home Depot. Not sure what to do short of complaining about lousy Whirlpool product. Next time will come to Consumer Affairs and research.

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

Please contact me if a class action Lawsuit has been filed for I am one of those who spent close to 3,000.00 for a lemon and to get the runaround. I spent every penny I earned to buy a long lasting fridge (Whirlpool Gold Series) only to have a headache ever since I bought it. Only owning a year the freezer went out, yes I had to endure the loud noise, no ice. Then the thing would spoil my milk and ham making my stomach to be sick. The temp is 60•. The people that Whirlpool sends out are in cahoots. Told me my compressor is out and I just heard it kick on. We are currently using refrigerator we brought out of the travel trailer kitchen because this thing sucked out all my money.

These products (Dishwasher, refrigerator, cooktop, and wall ovens) are less than 5 years old and everyone of is in of repair. The cooktop and wall ovens the repair on them would equal the price of a new one. I feel that the products should last more just a few years and also their warranties. This tells me they do not stand by quality of their products.

Purchased a Whirlpool dishwasher less than 2 years ago, began noticing a mildew buildup inside. Cleaned it, and bought dishwasher cleaner products, but the problem continued. Realized the dishwasher heater was not working. The dishwasher was staying wet, therefore causing mold. Called appliance repair, and spent 3/4 of the price of the 2 year old dishwasher to repair it. The control box malfunctioned. I was told by the repairman that that was unusual. At the suggestion of the repairman called Whirlpool. I was told since it was beyond the 1 year warranty they will comp us nothing. As a consumer I have no other recourse but to warn others, and to never buy a Whirlpool product again!

Bought dishwasher and a gas range about a year ago. Had to call the repairman twice on our dishwasher and three times on our gas range. Now it is little over a year and I am out of warranty. I paid extra and thought I was buying products of a good brand. I should have bought products from one of the cheaper brands along with the extended warranty.

Whirlpool Clothes Washer Model WTW4930XW1 - We have experienced tub overfilling on (2) separate occasions with this washer model in a period of time of less than (2) years. Through extended warranty service purchased, a technician came out the first time; declared nothing explainable to cause the malfunction, re-calibrated the control panel, and off he went. This second event occurred much the same as the first; happened to walk in to notice water on laundry room floor and witnessed overflow out the lid on top. We have carefully washed additional loads after this second event without a similar malfunction. From my online research, this sure sounds like a faulty pressure switch not sensing high water level in the tub. Any other thoughts?

I purchased the Whirlpool Duet Steam Washer and Dryer in the spring of 2010. Washer bearings just broke. I was told that the bearings in these machines are not strong enough to support the spin cycles. It is very disappointing to think that a company like Whirlpool would have their customers pay $1000 for a machine they know is not going to last. I agree with Julie. Maybe a class action lawsuit needs to be filed. Is there a lemon law for washing machines?

We moved into a new home (brand new construction) in Dec 2018. The ice maker/water dispenser has never worked. Weve had 2 different repair people come a total of 5 times to no avail. Now have to deal with Whirlpool directly to deal with Warranty. Will Whirlpool offer a new fridge? No, they will send a replacement door. 8 months later and we still have a fridge that does not work. Not impressed with Whirlpool and extremely unsatisfied with the produce. Do not buy this brand.

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.

My water heater burner went out after just over 3 years caused the pilot to go out. I was worried that although all parts were covered for 12 years and labor for only 3 and the labor would be very expensive. When I called and told them about the problem they said the part was covered and would ship it next day air but 10 minutes later another rep called and said they would cover the labor as well and to check a nearby service company as they might have the part in stock. Long story short without having to scream and yell my problem was corrected within 8 hours and all I have to do is drop off the new burner at the service company when it arrives. I have been lucky and haven't had many warranty problems in my life but none that I have had have been resolved so painlessly. I will never buy anything but Whirlpool from this day forward. Thank you Whirlpool.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

Washer MOD WTW4800XQ2 - I purchased this washer about 2 years ago after my 15 year old washer died. I have always used Whirlpool appliances as well as my Mother that recommended Whirlpool to me some 40 years ago. I knew when this machine was delivered and set up that I was in for change. It locks down to where you cant get in it for too long of a period of time. I am a really busy person, and HATE this, but if that were the only issue, I could accept that. We live on a farm and our clothes get really soiled especially in the warmer months. I like to pre-soak white clothes, NOT happening with this machine!!! It ends the cycle after about 30 minutes so I have to start over, wasting water. But the main issue is the machine tries to level the clothes, or whatever it is doing on its own before filling with water. I wash a lot of clothes!!! I am going to say that 90% of the loads of clothes that I have washed with this machine have been off balance, banging around bad. I then have to wait for it to unlock so that I can pull out the dripping wet clothes and replace to try and get it balanced. I am 59 years old, I got married at 14. So Ive been washing clothes for a LONG time... This machine is junk to say the least. I recently house sat for family. They purchased a new GE washer and dryer a little bit before I got these, wonderful machines!!! I washed dog beds, sheets, blankets and tons of clothes during this time. WOW, I had forgot that washing clothes didnt have to be torture. I will NEVER purchase another Whirlpool product. This washer has exhausted me. I purchased it at Lowes on tunnel rd in Asheville, NC. Please, if you havent already, junk this design... Its gonna lose your loyal customers. This complaint has nothing to do with where I purchased it. I did not contact the store as they did not design the machine. I did NOT want to pay for service on a poorly designed product...

I have called numerous times to complain about my new Cabrio washer. The first thing the employee did at the service center was to send me an owners manual, which I did not receive when I purchased the washer at Lowes. I followed all of the washing recommendations and still had problems with soap being left on the clothes. I called again and they said that perhaps there was something wrong with the washer and they were going to send a service technician out. I told her that he would probably not find anything wrong with it. I was just very unhappy with the product. She told me that we should check it out and not to worry. It was still under warranty and Whirlpool was going to take care of the service call. The technician told me that they have received many complaints about the machine, but there were no fixes available at this time. Yesterday, I received a bill from the service company for $129.00. I called the service company and told them that Whirlpool should be billed for this, not me. She told me that I had to call Whirlpool and if they wouldnt take care of it, I would have to. I then called Whirlpool, only to be told by the customer service rep that since they didnt find anything wrong with the machine, there was nothing that could be done. I asked to speak to someone else and she let me talk to her supervisor. She pretty much repeated what I was told by the first person and it is in the owners contract. I told her that I wanted to cancel the extended warranty that I just mailed in this week and she gave me another phone number to call. I cannot express how unhappy I am with your customer service department; the lack of compassion your company displays; and how I was told one thing and then charged a fee. It would seem that you have no eagles working for your company. I cant believe that a company as large as Whirlpool does not stand behind their products.

My range was made after this date and needs this Service Bulletin part. Whirlpool refuses to ship at no cost. I have spent money on this already to discover they knew the issue in April 2004 yet sold the range in October 2005. Rena in service stated she is the highest authority at Whirlpool anyone can talk to!

When I purchased my Whirlpool Cabrio washer and dry, I was told by the sales associate that this was the top of the line. I paid a higher price for what I thought was quality only to find out that this washing machine (WTW6600SW2) Serial number CU2973872 is in fact poor quality, made of components that are cheap, unreliable and made to last only as long as the initial warranty. Prior to buying Whirlpool, I owned Kenmore and had a washer and dry that raised four kids, now I own a Top of the line Cabrio that cant wash the clothes of two adults. I think it is funny that two days after the washer started sounding like a jet plane taking off during the spin cycle, I received your sign up for an extended warranty letter. Then I take the washer apart to locate the trouble and find it is a single bearing on the top of the drive shaft, but can I buy the bearing and replace it? No, I have to buy the entire outer tub and drive shaft. So a $10.00 bearing will now cost me $200.00. I am sure that helps your profit margins considering all you have to do is a search for Cabrio problems to find 350,000 hits, or to ask a professional technician and receive the reply that they are replacing 2-3 of these tub and drive shafts per week. I would recommend that Whirlpool tell its shareholders that you have compromised customer satisfaction to line their pockets with profits. If that was your intent then you have succeeded, however you need to also tell them to sell their shares now as you will have no return customers. Most corporations have core values that deal with safety first and then always followed by quality. I can say with confidence that your quality can be nowhere near the top five with this many problems with your top of the line product.

2 years of use the wash plate went. $150 later, one year later wash plate went again (the wash plate is all plastic, the motor spline in metal total stripes the plastic teeth in the wash plate) I replace myself. 3 weeks later the shift actuator failed which cost another $60 which I replaced. Now the bearing is going. There are only 3 people living in the house. I would stay away from the top loader washers from Whirlpool h2 low series. Huge disappointment.

Whirlpool microwave 1163XVS - I purchased a new home and a Whirlpool microwave in May 2010. The microwave has all of a sudden stopped heating! Turns on, spins, counts down, lights up, etc., but will not heat. Found this site by trying on my own to detect a possible reason and Im shocked to see these many complaints of the exact problem. Unbelievable, should be class action suit maybe for continuing to take money from consumers for defective product that Whirlpool knows about and appears to not take responsibility. Ive read enough, not even going to call for repair. Im buying another brand and spending more wisely this time. Thanks for the heads up. Shame on Whirlpool.

I have to wiggle everything just to get thru a cycle on my brand new dishwasher! It fills up and works great when it does work. No prob! But it takes a good 30 minutes to get it work and I walk away come back NO WATER! Sometimes I have to unload it just to wash them myself! Now Im going back to purchase place and return or have repaired. Less than year old, repair free?

I have had this unit less than a year and started having pilot problems. I would just relight and ask family members to take shorter showers or not run the washing machine or dishwasher at the same time. I would have to relight the pilot 3-4 times a year and would just tolerate. Now the water heater fails on a daily basis. In the last four weeks, my wife would say NO HOT WATER AGAIN. I am so tired of dealing with this, so last night, I called Whirlpool and associate was polite but gave me a lot of things that I should do (43 yrs a pipefitter). Before all was said and done, he is shipping me a new gas valve (at my expense) that I will gladly install to get rid of this problem. Will not EVER buy a hot water heater from Whirpool or Lowes ever again. Whirpool should stick to washing machines!

I was gifted a washer and ventless dryer for my condo. It takes a little longer than a regular dryer but it works great. It fits perfectly in a closet.

Buyer Beware!!!! Warning!!!! Dont buy Whirlpool. Youll be sorry if you do! Dont buy appliances from Home Depot. Youll be sorry if you do! Purchased new Whirlpool gas range 10/29/2019 from Home Depot. By February 2020 the front door fell off, its not cooking properly (18 min frozen pizza takes 30 mins to cook). Clock not keep correct time. Whirlpool unwilling to replace the unit while the third party repair company, “well you should have bought it from us, we stand behind what we sell.” They have no idea when or if the parts will ever come in due to COVID-19. Its been down 8 weeks now.Even under threat of a lawsuit Whirlpool said, Sorry we NOT replacing it, go ahead and sue us. We covered by our contractual warranty agreement. Home Depot said they are unable to help due to their contractual agreement with Whirlpool. I have a dozen hours invested talking Home Depot and Whirlpool on the phone and have no more information than I did a month ago. Whirlpool Case # **. Next step is small claims and public shaming of Whirlpool!

I bought the Whirlpool Refrigerator wrf989sdam00 in September 2013. Ive had nothing but problems with it breaking down within the first year. 5 days after the first year the 2nd cooling coil stopped working. After several attempts to get some help from the company I paid $500 for the second coil to be replaced. One year later that second coil has broken down once again, called Whirlpool and got nowhere. Ill have to pay another repair company to come in, AGAIN, to repair this piece of junk! Whirlpool does not, will not, has not, stood by their disastrous attempts to produce a refrigerator to keep your foods fresh. DO NOT BUY ANYTHING FROM WHIRLPOOL AS THEY DO NOT HONOR THEIR OWN PRODUCTS!!!

We purchased in July 2016 from Best Buy. Very nice product. Our former Whirlpool had lasted 20 years and was a work horse for our family. The new one began not freezing ice cream in November. Then, it would periodically freeze things very well and then not freeze items fully. We contacted Best Buy thinking we had a lemon. Worthless - no help. Told us to contact Whirlpool directly. The repair person came out today and told us that our refrigerator cannot be in our garage outdoors because the energy efficiency of the refrigerator causes it to shut off when the surrounding temp drops below 54F. Our former Whirlpool had been outdoors in our garage in that spot for 18 years, no problems. The new models now no longer operate if the air cools down around them. What!? There is no warning information, no sales information, no way to learn this until after you shell out 1000 dollars and lose your frozen food. It is in the manual in fine print, but we didnt read the manual cover to cover when we got the refrigerator, and we sure didnt read it BEFORE we bought it. And no one at the store, nor the installation people who represented Best Buy as paid installers told me I couldnt have this outside, even though I specifically told them I was buying it for our outside extra fridge and freezer to replace the old one, and the installers installed it outside. Technically our refrigerator is working as its supposed to apparently. However, I think it should prominently be noted on pre-sales materials that it must be operated indoors only (in climates always >54 degrees). Now I have a new refrigerator that I cant use as an extra in our garage. Apparently all the new fridges are energy efficient like this and shut off below 54. I cannot find any info on the internet about this, or any other complaints about a similar situation to mine. How does that make any sense? Freezing is 32 so any frozen goods will thaw, by default, always, if the machine is in cool environments. Phooey on this design spec. Dumb engineers.

Cabrio washer - This was a huge disappointment, clothes not clean, sometimes still dry in middle even with small loads! Have had washer just over a year, second time it has quit working! This time it wont even give a code to why it wont spin out! Living on a budget, I cant afford such a shoddy product! Never again will I buy any product associated with whirlpool!

My Whirlpool Cabrio Washer is less than one year old and quit working. Sears was supposed to come out and fix it (I even have the extended warranty till 2014). Service never showed up; when we called, they told us we had been rescheduled. Here it is the rescheduled day time slot and they still have not arrived. Im getting the runaround from them and I am supposed to be grateful because they gave me a $75 gift card for my inconvenience. Im on hold with Whirlpool because I just want them to take the washer back. I have been told by Sears since it is over 90 days, they cannot refund my money. I just have to wait for a repair which may or may not happen since they may not have the parts. This is unsatisfactory service from both Sears and Whirlpool. I have always bought my appliances through Sears and they have always been Whirlpool. I wish I would have read all these reviews before I purchased this model.

We purchased a Whirlpool upright frost-less freezer (model # EVL201NXRQ05) in October of 2008. So, you see, it is not even four years old. A few months ago I noticed that some things in the freezer were very soft. I looked at the back of the freezer and there was some ice buildup around the area where the coils are located. I took everything out of the freezer and removed the panel over the coils. There was major ice buildup on the coils. I completely defrosted it and dried it out. I restarted it and it seemed to be working okay. But a few days ago, when I got something from the top shelf of the freezer, it was not even frozen. So, here I go again. I removed everything from the freezer and have defrosted it again. However, this time, as soon as I turned it back on, the ice started building up on the coils immediately. It is impossible to contact anyone at Whirlpool that gives a crap. We have also been having problems with our Whirlpool Gold refrigerator. We have spent over $250 on it and it still is not working properly. I would love to just throw them in a ravine, but we have spent a lot of money on these appliances. We thought that Whirlpool was supposed to be number one in appliances. What a huge mistake we have made and it is costing us dearly.

If you want clean clothes dont buy this machine(Cabrio Washer)! First of all I find that my clothes have dry spot on them when I pull them out of the machine. Whirlpools response is that the machine spins at such a high rate that the cloth will actually seem dry. Doesnt make sense to me that a shirt that has another garment on top of it gets dry in an unexposed area. I have also been told to always use the high water setting. This helps but the clothes still are not clean. Also my dark slacks come out with residue lines on them - Whirlpools solution; never wash anything in cold water. In addition the machine is very noisy. It sounds like the water pipes are being kicked out of the wall. And forget about washing a king size comforter as advertised, a twin comforter doesnt get clean or even thoroughly wet and residue lines are left behind. Hate this machine! So glad I didnt buy the extended warranty since my attempts to have them stand behind this product have failed. I feel the money would be better used towards a different brand.

This is the information I tried to send to Whirlpool only to get a message that it was undeliverable: I purchased a set of whirlpool cabrio washer and dryer on 10-23-2013 (model numbers WTW8540BW, and WED8500BW). On 01-25-15 the washing machine failed to power up just over 2 months out of the standard warranty. This wasnt the low end cheap models. With cash discounts we paid over $1600.00 for the set. After a $70.00 dollar charge to the repairman we are told that the unit has a bad electric control board (part # W10761026). And unfortunately the part is on back order until March 1st, 2015 as of right now. So if and when the repairman gets the part and installs it, I get to pay him an additional $260.00. My family has always been such a dedicated Whirlpool appliance purchaser but this is wrong.Oh I almost forget, now I have to rent a washing machine at a cost of $55.00 per month until mine is repaired. I believed I was purchasing Whirlpool quality. The type of quality that doesnt need an extended warranty because Whirlpool is made to last correct? Please assist me in making this situation right and restore my faith in the quality I was raised with in Whirlpool products.

This refrigerator was already part of the appliance package that came with the property. I dont think if I had a choice, I would choose this brand. The stainless steel finish has rust spots, the top shelf has cracked and it is less that 5 years old.

Whirlpool Duet Steam Washing Machine WFW9500TW had F35/Suds code 14 months after we purchased the washer. Hose / air trap is clear and the hose from the analog pressure switch is connected properly. The appliance tech we had come out to look at the washer determined that the analog pressure switch was defective. He told us that this is a common problem with this washing machine. Whirlpool supervisor, Michael (female), stated that they could send a tech out - and charge us for the call - to diagnose the problem. She refused to transfer me to someone who could help and couldnt comprehend that the its out of warranty excuse isnt a proper defense for a product defect. There are many posts about Analog Pressure Switch problems with this washing machine.The posts about Whirlpools poor customer service are absolutely accurate. They are horrible - good luck in getting them to work with you. We read the reviews for the Whirlpool Duet Steam washing machine before purchasing one and we disregarded the bad ones as disgruntled customers. Please do not make the same mistake we made. After my conversation with their customer service dept today, I will never buy another Whirlpool product again. Defective parts happen. Refusing to fix a known problem is unacceptable.

Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

Very sad appliance company. I purchased a Standard Pacific Home in June 30, 2015 and moved in Aug 1, 2015. Use my Whirlpool Dishwasher for the first time back in Oct and it was not working properly. Whirlpool scheduled an appointment with Accord Appliance in Temecula Ca and the company was a no show. Called Whirlpool back and Rep Emma was very rude and had to call supervisor to schedule another appointment to repair dishwasher. Whirlpool have sad employees and sad appliance.

We purchased a new Whirlpool water heater April 2013 at Lowes and every 3-4 months the pilot would go out. My husband would simply re-light the heater, I guess he didnt think it was a big deal. However, in September 2014 the water heaters pilot went out and would not re-light, so I contacted Whirlpool about the warranty. It took 4 telephone calls (two of which involved a plumber, per Whirlpools request), and several days of cold showers for an authorization code to purchase a $8 part (thermo coupler). The hassles that Whirlpool put me through, no one should have to endure. Who ever heard of a technician telling you that they have to talk to the plumber, when you call them to explain a problem with your water heater, such as, the pilot will not stay lit and the plumber said it is the coupler (I couldnt remember the whole name of the part, but surely they should have understood what was wrong). Secondly, providing a plumber (unless youre married to one) to converse with them involves more money. Now I have a plumber at my house so I call Whirlpool and this technician insists that the plumber perform a test on thermo coupler to make sure that it was faulty before she gave the authorization for a new one. Yet again, when I called to Whirlpool with the plumber, while I was voicing my problems in resolving the issue of my water heater with this technician, and she just hung-up on me. So as not to be defeated and having already invested in the expense of the plumber, I called Whirlpool again and requested a manager. The technician asked if she could help and I informed her of my previous encounters. She apologized and took my information to have a manager to call me later; however, she did give me the authorization code for the thermo coupler without delay. When I went to purchase the part, I didnt have the old part (as trade; the plumber hadnt removed it), so I paid for it out-of pocket, to return the old part later.

We have had a Whirlpool dishwasher for about 2.5 years and have been happy with how it cleans dishes. About a year ago we replaced our counter top and in the process had to adjust the bend in the mountain brackets that attach the dishwasher to the underside of the counter. This requires flexing the thin piece of aluminum at the perforated line. In the process, one of the brackets snapped. The other was barely still intact and broke several months later. I tried jerry-rigging them, but eventually decided to replace them and called Whirlpool customer service to ask for replacement parts.Unfortunately, Whirlpool wanted to charge me $10.50 apiece and another $9.00 for shipping and handling. These parts could not cost more than a few cents apiece. I was shocked that they would charge me $30.00 to replace these flawed parts. Never have I had such and experience with any customer service department. The three people I spoke with were all rude and unapologetic about my situation. Two blamed it on the install...Ive installed plenty of dishwashers and never had any problems in the past. Even if it was a failure on my behalf, the simple replacement of the parts for a reasonable charge would have been fine by me. I told them Id be happy to pay a few dollars and to pay the full shipping fee (which was also high, in my opinion), but they refused to meet me halfway. I can only think that this is part of their business plan...make dishwashers with sub-par parts, and then over charge for the replacement parts when they fail. Well, I re-upped my jerry-rigging efforts and have improved the engineering of the faulty part. Save my $30. But Whirlpool will never again get my business and Ill be sure to steer clients and friends away from this brand as well.

Microwave Hood Combination...moisture sensor failed...potato caught on fire. Service company Whirlpool sent failed to show (Whirlpool selected a repair shop over 100 miles away). 2nd service company told me sensor failed and they would return with new part (ignoring the fact the white microwave was not gray and black) in a few days. If I wanted a new microwave without the dust and ash, I had to call Whirlpool. Whirlpool is ALWAYS experiencing a high volume of calls.Whirlpool states 7 - 14 days (unit on back order of course) for the microwave will arrive. 21 days later..no microwave. More high volume of calls... Whirpool state a repair center has received the microwave on July 31st and should have called me. Said repair center has no record of this transaction. Whirlpool reps claim to have records of my claim...but... they keep asking did we tell you it had been handled? I say read my file... Customer rep says my file is hard to understand (i.e. it is long). But they assure me they are empowered to help me. Maybe they should look up that word.Today...it is not Whirlpool customer service fault! No... It is being handled by a Product Replacement Specialist... Sadly they cannot provide me with any contact info for that Specialist. Empowered but not informed! Lesson: Whirlpool dont buy or if you do... and it catches on fire...just buy a new one... They make it impossible to get a replacement.

We made a major appliance purchases on July 1, 2010 of a Front Loading Washer and Stackable Dryer. The dryer required servicing at 11 months with was was covered but it required a major service for a broken motor control board. This has nothing to do with regular usage. The cost to repair is over half the total cost of the appliance.This is unacceptable on a 15-month old washer. Whirlpool would not stand behind their product or service. I had to purchase their Repair Plus 1 program to get it fixed. What a racket!

I had purchased a hot water heater on Saturday and installed it myself. I filled the tank and waited about twenty minutes before turning the power on. I waited a couple of hours before testing the water temperature and it was cold. I checked the temperature setting and it was set at one twenty five, I went to Lowes and informed the service person and was told there was nothing they could do about it, I had to call the number on the tank for Whirlpool. I called the number and was told they could come out to check it but we would be responsible for the labor charges. I didnt understand why because it was under warranty and we had also purchased the extended warranty. I informed my wife so she could deal with Whirlpool because I was going to work. My wife called a number of times and was getting transferred from one person to another and getting no help at all. She was told by one person that it was maybe a problem with the wiring in our home or maybe the plumbing. One person told her that it was not their problem. We had to finally pay an electrician to come out to look at it and had to pay him to replace a heating element. The cost of the electrician and the part came to an extra two seventy five dollars. The only real help that we received was from Lowes managers that were willing to take the water heater back if we could get an authorization number to return the water which Whirlpool claimed they did not have any type of a number. Our 400 dollar water heater turned into an almost 700 dollar water heater. We had also purchased a refrigerator from Lowes that was the Whirlpool brand that quit working after about four months and we had to pay to have it fixed. Needless to say, we will never again purchase any Whirlpool products or recommend them to anyone. The service was very very poor and we are not happy with Whirlpool.

Whirlpool gold model GI6FDRXXQ06 - This fridge is 3 years old and we are about to put the fifth ice maker in it. Vegetables freeze in the vegetable drawer (yes, its set correctly). Our repairman even says the design is faulty but since the warranty is out, we have to keep replacing the units!

A few weeks after we bought it, the washer was already having issues spinning out, and the clothes would have to go through another rinse and spin cycle. A bout a year and a half in and I had to replace the pump because it stopped draining. Even carefully loading the machine, and at least two or three times a week it would not spin out. Two weeks ago it stopped agitating actually performing washing action and spinning out all together. Last night I replaced the actuator which controls the speed or lack thereof in the spin. Still nothing. Ive reset it multiple times, still nothing. At least the clothes are getting wet. At tax return time I am replacing this piece if garbage and I will never get another whirlpool, or Maytag washer again because from what I have been told by dealers and repair men; they are all garbage.

About three months ago the freezer iced up. Tech showed up stating that the motherboard went out, needs to be replaced, had to wait 6 days for part to show. Was replaced. Two weeks later freezer iced up and refrigerator got hot, lost a lot of food. Again motherboard went out again, had to wait another six days. Part came in Tech replaced the motherboard and installed a heater defroster. Worked for 2 weeks and now the freezer is icing up again. What a pain in the ass.

Very functional microwave which also comes in convection oven if needed. Stainless steel, finger print resistant, is very handy and easy to clean. Overall very happy with it so far. Much better than the earlier Samsung that we had.

I bought a matched set of Whirlpool washer and dryer. Within about 3 months the dryer quit running on any of its cycles except heavy duty. About a month after that the washer started messing up. First it quit putting in the bleach. Next it quit adding water except under the heavy duty cycle. Then after about another week or so it quit putting in fabric softener. After a couple of more months it only uses hot water. Now not quite a year after I purchased it the washer now only adds water in the wash mode and not the rinse cycle. Now all this would not be a problem except I had lost the warranty cards and in their website would not let me register it online.

Even with the hottest water on the most heavy duty setting, regular dinner plates are not cleaned. The flatware holders that are set in the door (instead of free-standing in a rack) do not have adequate holes in the holders and are too far away from the limited jets to get adequate soap and water to cleanse the flatware. Even after rinsing all scraps off the plates and flatware, we find bits of food, gravy, or smudges on the plates and flatware - since its first usage. The manufacturer had the audacity to claim that was normal. Settings include delayed starting, heavy duty versus normal washing, and different types of drying. The heavy duty washing is definitely poor quality, and there seems to be no difference between any of the drying settings. The delayed start is nice. The physical layout of the prongs on the racks and the folding racks do not allow easy fit for most sizes of pots plus plates on the same bottom rack. I cannot put a 1 gallon pot level on the same rack as dinner plates. I must put it beside salad plates. Only small sauce pans fit neatly or cleanly beside dinner plates. Yet the external dimensions of this dishwasher are the same as the competitors standard size. Looks neat and is easy to clean. Also, the exterior does not show scratches. Actually, I cannot see where the exterior has any scratches. The service people were very little help. The Warranty said that after five (5) service calls the unit would be replaced. We made six (6) service calls, but we were told that we did NOT have six because if you called again within 90 days of a call, that was considered the same service call. That requires 450 days minimum to have five (5) qualified service calls, but that warranty was good for only 365 days!

Whirlpool refrigerator - I purchased $6950.93 in Whirlpool products in one day last year at HH GREGG in Lexington, Ky. The refrigerator was purchased on that day September 18, 2012 and my kitchen wasnt going to be ready until December, but I wanted all items bought for measurements (specs) for the new kitchen designer. HH GREGG delivered to my garage October 26, 2012 because they couldnt hold any longer, but when we purchased that day they promised to hold till December when my kitchen would be finished. I have Proof from the kitchen installers the day they finished, December 28, 2012, was the day the appliances were installed. Well here I sit typing this letter on January 7, 2014 and my Whirlpool refrigerator is as of right now is in need of a compressor while losing approx $1000.00 in purchased food. In other words, approximately $900.00 in repair cost. Isnt Whirlpool a large enough company to stand behind its products when I paid $2599.00 for this refrigerator for at least one year from installation instead of purchase date? My fiancee has been trying to work out a solution with Whirlpool and the parts are on back order now. For at least two weeks we have been without a refrigerator and have two young children. Doesnt it show that the parts being on back order from Whirlpool, barely being a year old prove the defective product is being sold to the public daily? I plan on going further with this action due to the name Whirlpool all over my kitchen which disgusts me. Im going to write every columnist I can and do all I can with what little resources I have against this large company if no one helps us. This is absolutely an injustice against consumers...

Whirlpool Cabrio washing machine WTW8800YC0 - My washing machine that I purchased a little over 3 years ago apparently is a piece of junk. Ive noticed a smell in the past few months, even while using Affresh. Now, its making so much noise that we must close the laundry room door while the washer is on. I called customer service and they will sell me a new 1-year warranty for about $345.00. Customer service thinks it sounds like the motor or the gear box! After reading the reviews on this washer, its not worth it to repair. More trouble looms for us. Whirlpool doesnt stand behind the product and as many complaints as there are, the washer shouldnt even be sold anymore! Never buy Whirlpool!

I have the same pilot light problems as everybody else. I pulled the burner unit out, and cleaned, and blew everything out, and took a wire brush to the openings on the floor of the unit. I called customer service, and was asked about ventilation. I didnt mention that the heater still didnt work, even when the door to the tin water heater was removed, so venting is not the likely culprit. She authorized a repair that will likely do nothing from the comments I see.The real problem with their customer service, is the apparent stupidity of the computer system. She asked me for the model and ID number. I had to cut through the extra insulation blanked on the tank to get it. However, when I gave it to her, she then asked me if I was ** and if I live at **. If this information was already in the computer, why couldnt there be a search by my name and address, to get the model and serial number. Obviously, I had registered the water heater in the past. Isnt being able to get this information the reason to register in the first place?Now, I have to replace the extra insulation, all because of a stupid inability to create the necessary searches in their customer database. Yes, I could have written the numbers down, but why have the customer registration at all, if it isnt to be used for anything, other than data mining of the customer base.

Whirlpool gold bottom freezer is 2 years old. This model has a design flaw. And due to this the drain is frozen in the bottom of the freezer. Water is leaking onto the floor. I called for service and whirlpool is charging me. To fix a problem that is their fault. This is unfair.

I like the double bottom french drawers but I don’t like that the top door hinge covers are plastic. Also I wish there was more height inside the refrigerator for tall bottles and pots. The wheels are great for moving.

I bought the Whirlpool Cabrio 5.3 cubic foot washing machine to replace a Samsung equivalent machine. I am so extremely disappointed with it. As a mother of nine (seven of them boys) I need a quality machine. Unfortunately this is not one. The clothes come out of the machine just as dirty as they went in. The pants still have dirt on the knees. I think a rinse in the sink would yield better results. I use the highest soil setting, warmest water fabric will allow, and exclusively Tide detergent. I only fill the tub with half a load (completely voiding the value of large capacity) and yet still have to run clothes through twice.I really don’t have time for this. All the kids clothes have to be inspected before drying. I wish I could go back in time and keep my Samsung which was recalled. I would rather take the risk of an exploding machine than deal with this one any longer. Unfortunately, after spending over $1000 on the washer (and buying the matching dryer) I’m stuck with this useless machine. I hope others don’t make the same mistake I did.

Rather than replace the heating element in my 15 year old Sears dryer, I opted to replace both my Sears washer and dryer with a new HE Whirlpool. It was the biggest mistake that Ive made. The washer does not have an agitator and the clothes turn into a twisted knot. Deodorant did not wash out of load of three sweaters. When I called tech support, the woman told me that the washer met specification. I suppose that means that it uses only limited water but has nothing to do with the cleanliness of the finished load. I was told by the repairman that future calls regarding unclean clothes would cost me despite a warranty that I purchased from Lowes.He suggested that I wash on using the Bulky Items setting and with a specific laundry soap. The setting provides more water but without the agitator, my clothing turns into a huge knot and comes out of the machine dingy despite washing loads for over 60 minutes at a time. My electric bill has gone up because I have to also add an extra rinse. The machine frequently become unbalanced. My dryers seal started loosening up two years after my purchase and finally became twisted in a sheet and ripped itself loose. Whirlpool has lost all future business with me.

I’m a 69 year old married man who has probably owned about 8-10 clothes washers during my life. I purchased my first Whirlpool washer about 1 1/2 years ago (Cabrio - model WTW8500DC2). It began leaving sediment on my clothes immediately, even though I followed the specific washing instructions. Whirlpool sent 3 different repairmen to fix the problem, each indicated there had been problems with this machine. None were able to fix the problem. When I called Customer Service for the 4th time, they refused to discuss the problem. They said there was nothing wrong with the machine, it was my problem, I must have too much “lint” in my clothes. Haven’t had that problem for 69 years, but this was their way of handling the problem. They refused any further help. I would discourage everyone from buying a Whirlpool product. I absolutely do not back their products. You are on your own!!

I hate my Whirlpool refrigerator: It has a upper freezer with no light. The shelves are not split and raising or lowering shelves gains nothing and may even take space away. I would never ever buy another Whirlpool.

My very expensive Whirlpool refrigerator thats three and a half years old broke down before Thanksgiving 2020. I am not able to get parts until after May 18th 2021. After calling numerous times and spending lots of time on hold I was told February 11th by Whirlpool that they had the parts in stock and they gave me a price for each part. Then they connected me to the parts department where they told me they dont have two of the 4 parts that I need. The price that they gave me for the same parts with a lot higher than what they told me at whirlpool. Whirlpool customer service was terrible its as if they dont give a damn. They just dont care.I cant believe its going to be 7 to 8 months to get parts for a three and a half year old refrigerator. I have fallen down my basement steps where I have a small very very old refrigerator twice carrying food up and down. Spreading mustard and sour cream all over my carpet my stairs my walls. Not to mention the fact that I have bruises all over my body. If I were you I would not buy a whirlpool. Its going to cost over $600 for the parts replacements that is if I can ever get them. Im going to have to break down and buy another refrigerator. Remember Whirlpool customer service is terrible and you can just forget about getting the parts.

Purchased a 80 gallon Whirlpool Water Heater with a Life Time Warranty. When it overflowed because the system failed to detect the water temperature, called and they sent in the temp sensor (I paid for shipping). Had plumber replace it. One day later the same thing happened, called and they sent in a board. Same exact thing happened. By this time, Im without hot water for over 2 weeks in dead cold January on the East coast. They will replace the water heater but only a 50 gallon NOT the 80 because they no longer manufactured the 80. Option given by Lowes is to add a recirculating pump to give additional gallons. But, of course Whirlpool said NO. They only can give me the 50 gallon. What a ripoff!!! Please, please DO NOT purchase any product from Whirlpool. Now they change the same to A.O. Smith Signature Premier.

We have owned the Whirlpool Quiet Partner II for about 2.5 years. We purchased this from our local Lowes store (on sale). For the first few months, everything was fine. Then, the dishwasher stopped completing a full cycle and left the dishes somewhat dirty. I found online that I could reset the controls by pressing heated dry-normal-heated dry-normal quickly.When the cycle starts, I press cancel and then set the cycle I want and it will do it correctly. I do this every time I wash the dishes since I dont know when it will decide to stop working (wasting water and soap to redo).Now, the dishes are not drying and water collects on the ceiling of the tub. I saw this after a smell was coming from the tub (like mold) and when I looked up at the top of the tub, I saw water droplets hanging there and mold forming around the sprayer and back of tub. I have to wipe the ceiling dry now or just run vinegar through it often. I cant see paying someone to come out since service calls start around $70 just to come to my home. I did look at reviews for the dishwasher before buying but I wished that I had seen this site first. I would not ever recommend this dishwasher to anyone!

Ordered water filters for refrigerator. They did not arrive. Tracking # came back not found. Waited on phone for an hour. Talked to representative. She could not help me. Transferred me to another department. Been holding for an hour. Still no help. If this is what Whirlpool calls good service, they are completely lacking. I will not order another Whirlpool product.

Why does your AquaLift self-clean feature not work? Tried numerous times & have been scrubbing all afternoon... Horrible!!! My last oven (Maytag) self-cleaning feature worked awesome, just had to vacuum out ashes & wipe down with regular soap & water. Have no idea what to do to get this oven cleaned!!! Very frustrated...

This morning is the fifth morning I had to take a cold shower. My hot water heater keeps going out. When we call, we are told to dust the underneath better, as it sucks dust. Are you kidding? The hot water heater is still under warranty, which means I will have to spend around $200 to have repaired again. So much for top of the line.

I had a 6 year warranty on the new Water heater and about only 4 years into it the tank began leaking. Whirlpool replaced it but of course I was responsible for Parts and labor to replace it. The replacement only lasted just over only 2 years and just outside the total of 6 years from original purchase date on the first. Whirlpool refused to discuss it since it was a few months out of warranty. If someone else has purchased this heater it would have failed at 2 years and they would have had to warranty it anyway. I will never own another Whirlpool appliance because of their substandard products and warranty. I only wish I had reviewed the reviews of others and taken their experiences into consideration and not purchased Whirlpool. I am now out for another heater and reinstallation charges again.

We purchased the Induction Range Whirlpool Model WF1910H0AS0 almost 2 years ago and bought the extended warranty that was offered by A.J. Madison. We started having problems about 8 months after the purchase. We have had technicians out numerous times and they couldnt solve the problem of the cooktop part of the range locking and beeping when we use the oven. I have made several calls to Whirlpool and basically was told too bad. I see that there have been several complaints with the product and they have stopped making it. On one repair visit we were told that they were replacing a particular part because they were having so many problems with the heat blocker that goes under the glass top that they made it thicker and were hoping that this would solve the problem. It did not.The thing that really has sent me over the edge is that last night I was just boiling water and I heard a pop that came along with a smell (electrical burning smell) and the range blew a fuse and now the cooktop part just shows the deadly error F47. I am so disappointed in Whirlpool and their customer service and too bad attitude. You would think when you are spend almost $1800 for a range that it would not have problems so quickly and pretty much render useless in less than 2 years. Also shame on A.J. Madison for selling extended warranties through a company that has such a bad ratings with the Better Business Bureau. The only reason I gave 1 star is because you cant have no star.

I bought at Lowes. The first one was sent back (doors stuck, suction cracked lining). Now the temps are not working in the fridge or freezer. All the food got dumped. Its sad. My old one lasted closer to 25 yrs. (and may I add up to ten children). This one has only been used by adults. I thought I could trust Whirlpool?! I sent info to local Lowes. We will see if theres any help.

My Whirlpool dishwasher is used 2-3 times per week. The interior has more than adequate space for a full load of pots, plates and utensils. A normal cycle is used and the washer is essentially very quiet. Dishes/glassware always come out spotless and squeaky clean.

We have a Whirlpool range that was produced for Kenmore (Sears brand). It’s a glass top with electronic controls. Over the 13 years we have had this range we’ve had to replace the controls 3 times at a cost of over $300 each time. Each time we were under severe lightning storms and got hit with a surge. It would burn out the Control board. We finally got a whole house surge suppressor since a large device is required for 240 volt appliances. Also the glass top has gotten scored over the years. We would not recommend this oven and will likely replace it with an industrial gas stove with manual controls when this one dies or gets too expensive to repair.

After the pilot light on my water heater would no longer stay lit, I contacted the Whirlpool technical support number listed on the unit only to be told my unit was still under warranty, but I would be responsible to pay a $65 diagnostic fee and any labor associated with a repair. The technician came and said my ventilation system was the problem and didnt even touch the unit. He then sent a report to Whirlpool that the unit was flooded which voided my warranty. He did not submit photos to substantiate his water damage claim and now Im being told the unit is unsafe and must be replaced at my expense. This all sounds like collusion to not honor the warranty! I will never purchase a Whirlpool product again!

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

Whirlpool Cabrio Washer - After 15 months, washer bearing have gone out due to tub seal leaking. Repairs are $450 but repairman doesnt want to touch it due to he know it will go out again. Whirlpool said Im sorry. Lowes said these are coming off the shelves soon but there are still some for sale. DONT BUY!!!

We have the four-door model, french fridge part, drawer, and bottom freezer. Overall has been a good appliance. Icemaker burned out in third year. Icemaker replacement is very noisy, popping and groaning during drop-out and refill. Noise level otherwise is average.

I purchased a 50-gallon Whirlpool natural gas water heater (12 year warranty) from Lowes approx 2.5 years ago. Just before Thanksgiving, the pilot light started going out once a day, then twice a day. Now, I can light the pilot light in Pilot mode but as soon as I release the red button, the flame goes out. I called Whirlpool and received phone troubleshooting support resulting in a recommendation to pick up a new thermocoupler from Lowes which I did. While searching for someone to install (unfortunately Im not that handy), I ran into the thousands of complaints filed about the very same problem Im having over a number of years and right up to todays date. I called Whirlpool back and got the same song and dance. Theyd be happy to help me troubleshoot if I can get the required meters etc. to test devices, do draft tests, etc. They claimed the problems were fixed with the newer model that I have but certainly cant explain why I have exactly the same issue. What they are not willing to do is stand behind their product and get me hot water. Tried calling Lowes and got the response that I have to deal with Whirlpool. It appears that this newer BFG model is just as flawed as the older model and the warranty is pretty much worthless other than getting a few parts. I used to think that Whirlpool products were reasonably good, however, I will never purchase another.

I am done with Whirlpool. Everything I have bought is failing. I bought all new appliances when moving into my home. Dishwasher, 2.5 years old, quit. Cost is going to be as much as a new one. Refrigerator quit at 5 years old, what a mess that was. Paint is peeling off my clothes washer. I am not going to buy or recommend any more of this junk.

Ive always had good luck with Whirlpool. They last longer & dont have as many repairs. Ive had to have a lot of repairs with Maytag washers. The dryers didnt give any trouble. I recommend Whirlpool.

I bought the #1 rated Consumer Reports recommended Whirlpool Gold fridge 15 months ago (how convenient their warranty stops at 12 months). The control board has already gone out, lots of ruined food and ruined perception that Whirlpool made good products. I will avoid buying anything they make again. When repairman was taking it apart, I saw Made in China stickers.

Where to begin? I bought Whirlpool Duet Front-Load Washing Machine about 11 months ago after my top load bearing went bad and start making a lot of noise after 8-9 years. 4 months ago (6 months from purchase) it started to act strange; washing machine will not unlock after a cycle, start throwing F3E1 error. Thats when I first called their support service. Their service technicians are very nice actually. They seem to be local small appliance shop, contacted out by Whirlpool, from my guess. Initial visit was to inform me that Im using WAY too much soap, while I was only using well below what was recommended by Whirlpool manual. RED FLAG #1. Technicians told me to stop using too much soap or start using POD. Also to flush my washing machine with 2 cups of white vinegar in hot cycle every few weeks. Ive changed my soap to Tide POD and starting flushing my washing machine immediately after he left my house. It was running OK, but I still saw F3E1 error at the end of every other cycle, until... thing went really bad one day, it simply stopped responding any command while clothes was still in the washing machine. I unplugged power cable and plug it back, it hums for 10 mins and in the end it was the same result. After several attempt, it finally unlocked itself, thus I could wash my clothes at my parents house. This is when I called support service 2nd time. The same technician came and this time, I had video recording of everything. He could not dismiss this with simple soap theory, so he opens up the washing machine and tells me that its due to bad control board. He proceeds to order new control board, which took a few weeks. New technician comes back with new control board and installs, runs a few test command (not full cycle) and leaves. During this whole time, Im left with no washing machine at home. Good thing I travel sometimes and laundry is done remotely sometimes. This repair didnt improve the situation much. I called them back for another appointment. Another technician comes back and tells me that Whirlpool sent back BAD control board. Now, Im really suspecting their product is really piece of **. At least at this point, I was still happy with their service. He leaves my house claiming that they will order new control board and re-install.A few days later, I receive a call from a lady, claiming that Whirlpool has instructed them to ask me to use different outlet, since they believe my outlet is causing issues. Now Im really pissed. Coming from electrical engineering background, I know theres always any chance, but they should double check this with their own technicians. Anyways, I perform their recommendation, which I knew was a shot in the dark. During this whole ordeal, Im working on a project that are out of state (CA). Not only do I have time to stay home for all these service visits, but Im not even home to test my washing machine. During one of the holiday, I was able to take a few days off. This is when I decided to take different approach. I went to the retailer, whom I purchased my washing machine from. They were also nice, but theres so much they can do.I called Whirlpool direct line to explain my situation, how unhappy I was, and to replace my washing machine. Their response was by the book: We can only execute our warranty policy and replacement is not part of warranty. The representative specialist had enough nerve to ask me why I have not called back in several weeks and continue to repeat it as if its my problem for not reporting back. I had spent 2 months of supports and 4 site visits, where I had to reschedule my work or take a day off, before travelling for projects after holiday seasons. This representative really took customer service to next level of hell. In the end Im without properly functioning washing machine for 4 months. I have to coordinate with my parents to use their washing machine when Im back home. My advice, you should really think 3 times before buying Whirlpool washing machine or any other appliance. Also consider that youre on your own, when their product malfunctions, and youll be sitting on dead appliances.

My 2 year Jennaire (made by Whirlpool) broke down on 12/14/11. Repairman came out on 12/19. He said that the compressor was not working and ordered another and he came out again on 12/22. He said that it could not be fixed (internal leak or something). An aside to this story was that a tank of compressed oil blew and damaged my hallway and kitchen walls and floors and 2 rugs. That was being handled by the repairmans insurance company.We called Whirlpool and they said that they we could pick out a new refrigerator priced at no more than $2399 even though we paid $2799 for the Jennaire and would have to pay the difference for a model costing more. We went with a Maytag (Whirlpool product) that listed for $2899 but was available at 2 local stores for $2050 and $2100 but I had to give Whirlpool anther $500 because they use the MRP.They finally delivered it on 1/5/12 but would not leave it because no one disconnected the water line to the appliance and they would not touch it. It took me 20 seconds to do it and if they would have told me so it would have been done on the 5th. Rescheduled delivery for 1/8/12 and the unit was delivered damaged (large dent in front) and they would not temporarily leave it until a replacement came.I called Whirlpool again and asked them to just call a local Home Depot or anyone in my area (all had the unit in stock) to deliver one but they told me that it must come from the warehouse in Michigan (I live in PA) and that it would be yet another 5 to 10 business days to receive it. So, I am paying $700 more for a unit that I could have bought and had delivered before Christmas not to mention the inconvenience of no unit for a month. Not to mention the damage to my home, $200+ dollars in thrown away food, time to shop for new unit, time for 2 repairman appointments and time for the 2 deliveries thus far and countless phone calls to Whirlpool to get the new unit.Today is 1/10/12, so I guess Ill have by month end if there are no other problems, you would think that they would try to expedite this just because its been so long or give us a substantial credit for all the trouble. Never again Whirlpool.

I bought a washer dryer Cabrio set and the washer after 2 years has a bearing failure and is squealing badly. The service technician quoted $400.00 to fix a washer that cost me $800.00 new and is 2 years old. I had a Whirlpool washer and dryer set for 11 years with minimal issues and that is why I bought Whirlpool again. This will be the last time. It is a matter of time before the washer fails and I will have to purchase new or pay the service technician.

We bought our Whirlpool Cabrio washing machine and dryer in October 2010 and it was the worst purchase we have ever made. We had two worthless calls to Whirlpool and all the regular brain-dead suggestions that do not improve function. We have had a technician out to our home and we have the extended warranty. The technician stated that the machine will never function properly and Whirlpool knows this. The low water level prevents washing, rinsing. The problems with the washing machine are many and the required multiple washes and rinses make the claim for low energy usage false advertising.It leaves white streaks on dark clothes constantly and has residue on everything from sheets to silks, no matter the cycle. Theres not enough water which covers the clothes, so clothes do not get clean. The spin cycle is so violent that clothes are damaged. The soak cycle is a joke. Soaking means to sit in water and soak. This machine drains the water so there is no soaking. With this very expensive machine, we can use only one cycle; bulky items on the low spin with a repeat rinse. According to the technician, these complaints are what they respond to all day, everyday. There is no mechanical fix for this design flawed machine. If you are looking at buying this machine, dont! The machine has ruined lots of laundry. Do not waste your money or your time. I would like my money back. The Whirlpool company definitely plays dumb on the customer service calls. Its a non-functional washer as it damages laundry and has false claim for low energy usage.

Warranty services are trouble. For one (1) simple washer part its taking over 2 months. They state its on back order...while my food is wasting away. Whirlpool didnt even know what he was doing, and to the top it off, forgot to put back the part he took off!

I had the best experience when I purchased my washing machine and dryer. The personnel were professional and very pleasant. I am quite pleased with my washer and dryer. I have had a couple of minor problems but the warranty that I had on them was excellent.

My KitchenAid side by side refrigerator/freezer is a beautiful thing, shiny steel surface, gleaming white inside. However, its made poorly. The ice cube maker compartment broke and the replacement came without any installation instructions. It was hard to figure out and I broke it. Now, everything in the refrigerator is freezing and changing the temperature on the digital panel makes no difference. McKinneys appliance, where I bought it, no longer has a refrigeration technician and they referred me to Whirlpools 1-800 number where I supplied some information and sat in my chair on hold listening to music for a half hour before hanging up.The recording on the phone suggested their online chat where I was asked the same sorts of questions and was told I would get the answers I wanted by paying $5.00. I had no idea what I was getting into but I didnt pay, just terminated that inquiry. Feeling cheated by the company whose product I had mistakenly purchased. Im now running the risk of a technician visit, sometime between 8 am and 4 pm a couple of days from now. I have to be prepared to wait around all day for somebody to look at my refrigerator, charge me a lot of money and, from what Ive read online, potentially see the problem return in a very short space of time.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

I bought a whirlpool washer from Whirlpool on February 27, 2011. Since then, they have come out and repaired the washer for 5 times. They have even taken the whole motor out, and replaced it. The last time they came, they said I would have to pay for the next time. Now, it has broken again, and I have to pay for a washer repair that is less than a year old. We bought the Whirlpool washer at Sears, and neither Sears, nor Whirlpool will stick by their product. We cannot afford another new washer, and to pay for repairs is a stretch too. Is there anything you can do?

We our adding our name to a list that is remarkably long. We purchased a top loading Cabrio washing machine just over a year ago and the problems with the balancing of the unit are the same as everyone else who has written in. The service company A&E has promised a lot but has done little to resolve the issues we have had with the machine. One representative told us that she would order the part and have it sent to our home. When the part did not arrive, we called A&E back only to find out it was never ordered because the service technician would not return their phone calls. I find this excuse ridiculous and similar to other false statements they have given us on the other four phone calls made to address the problem. After reading these reviews, we realize that this is only the beginning of what will be a frustrating and costly experience. Never again will we buy a Whirlpool!

Two years ago, we purchased a Whirlpool Cabrio Washing Machine from Sears. All of a sudden, it was making sounds in the spin cycle that sounded like a jet airplane taking off. It was terribly loud. We called repair technician, which cost $90, only to find out that the bearing is gone and its going to cost over $500 to fix it. This is absolutely ridiculous! We expected it to last several years, only to find out that we would have to spend almost as much as the washer originally cost in order to fix it. We paid $700 for this machine, two years ago, and I can say that Ive never been more disappointed with a product in my life. My previous washer lasted thirteen years, not to mention my dryer and stove fifteen years, with minimal repairs. I will never buy another Whirlpool appliance again. I have read some other complaints on this consumer affairs website, as well as other sites, regarding this same washer with the same problem on the bearing and cost to repair. If anything, I think Whirlpool should make good on this product and offer something regarding a recall or payment for repair in some form. As far as Im concerned, I will alert everyone I know about Whirlpool appliances and advise them not to purchase it. Now, I either have to pay over $500 to repair my washer or go buy another one. I do not even want this Whirlpool appliance in my house when I can get a washer for cheaper than the cost to repair it.

We own a Whirlpool microwave hood combination. The door started cracking where the handle attaches. Ordered a new door and installed in July 2017. 18 months in the door and the handle have both started to crack again. This seems to be a problem with Whirlpool microwaves but they wont stand behind their product. Theyll send someone out to replace it for $$$$ but they wont admit they have a flawed product. One year warranty - no exceptions. Will have to replace the microwave and it wont be Whirlpool!

Bought this refrigerator in June 2018. Had issues with freezer section and service technician came July 19. Issue was resolved but only temporarily. Had another technician come in Oct 3 and was told he had to order a new freezer drawer which should take 3 days. Now being told the drawer won’t arrive until Nov 15. You call that service? It would have taken less time to get a new refrigerator. I would never recommend buying Whirlpool products to anyone. What’s the point in buying a product that you can’t get proper service on.

My double oven is only 6 years old - it stopped working on xmas day, had a repair man look at it. He has phoned Whirlpool and has not had his calls returned to buy the part needed. Why is this. I need my oven, why is Whirlpool making it so hard for me to have it repaired.

I bought a Whirlpool Duet Washer and Dryer in September 2013 and washer is already broken. It leaks out the front of the front loading door (yes, I clean it as advised, including leaving door open to air dry etc). I am a retired senior citizen and my wife and I spend 6 months of the year in Florida so the washer has barely been used since we are barely home and its not like we are trying to wash load after load of heavily soiled items daily. I would not recommend this product at all!! The repair people said it would cost approximately $300 to fix and offered a plan to fix it for $350 with a 1 year warranty. Why should I bother to do either if I will have to do same after 1 year? This machine is barely used and broke?! The customer service people were not helpful and seemed only interested selling me the repair plan to fix what should not need fixing. So, to recap - I bought the machine in 9/13 then went to Florida from 10/13 to 4/14 (so it was used 1 month). Then, it was used from 4/14 until 10/14 (6 months). I returned from Florida this year in April 2015 and it started leaking in June 2015 (2 months). So, my machine has been used for a grand total of 9 months and it is already broken!!! Stay far away. Whirlpool should come and replace this machine for us for free if they care anything about customer service and senior citizens but clearly they do not. In Florida we have an old Sears Kenmore machine that has lasted for over 20 years!!

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

Model # WFG510S0AS1 SER #R30850040. Oven was installed NEW in the home I purchased in July of 2013. I used the cleaning feature on it in Nov 2014. I am amazed that it did not start a fire. Please see pictures attached. The whole control panel melted. This makes the oven unusable and extremely dangerous. I will need to replace the whole control panel. I followed the instructions completely in the manual provided for the cleaning cycle. It says in the manual to only clean the over this way as using easy off or any other cleaner will damage the inner surfaces.Whirlpool claims they have no knowledge of this problem but there are numerous complaints on their site about it as well as other internet sites complaining about the melting of the control panel. I need to know how to fix this problem and dont believe I should have to pay for something that is obviously a flaw in the materials used. It is extremely dangerous. Since these pieces of Whirlpool equipment were installed by the broker that originally purchased the home, I have no record of purchase. I can try and contact him and see if he has anything but kind of doubt he has receipts now.

I bought a French door, counter depth, Whirlpool refrigerator model GIOFSAXVY05 in 2011. It leaks water under the front of the freezer on to my cherry wood floor. This has caused much damage to my new house and floor. It is noisy, runs a lot, but its the leaking that has me most disgusted. I wish I would have known about this defect before purchase and ruining my floor.

New whirlpool washing machine 2016 - This washer is supposed to be smart, but it NEVER fills up with water! I always have to fill a bucket with water and throw it in the washing machine. My clothes do not come out smelling fresh and its not the detergent to blame, its the washer! Im so disappointed with this product. Whirlpool should stop making products.

Purchased a Whirlpool French door in April 2020 during the pandemic for 2K. The first week of owning it my fresh vegetables froze. I lowered the factory set temperature by one degree. The next week the ice maker stopped making ice. 3 days later it started up again. The 3rd week my freezer food defrosted and the ice maker stopped making ice. Called Whirlpool And requested a refund. They said, No we will send a tech. The tech determined the control board was defective. I had to empty the entire fridge and turn it off, defrost it for 24 hours. The headache to find someone to take your food! The part took 2 weeks to get replaced.The tech said, If this doesn’t work we will have to come back and take the back off to see what the issue is. Told to defrost again for 24 hrs. The ice was so thick we did it for 48 Hrs. 1 week later ice started to form in the freezer and the ice stopped working again. Called whirlpool demanded a refund and they said no. A tech will come again. I’ve relocated my food 3x already. How many more times can I do that! Whirlpool is not concerned about their reputation at all, as I read through other reviews of situations similar to mine. Do not buy whirlpool!

I bought a fridge from this company not even 14 months ago. Went away for a week and came home to a fridge and freezer of rotten food. The fridge had died - Im guessing not long after I had gone away by the look and smell of the food and house. I have had nothing but the run around ever since that day. Spoke to this person and then that person. The electrician confirmed that my fridge is completely dead because of the compressor. So they sent a report to Whirlpool and they have now confirmed that I will get a new fridge. Now Im being told that will take 7-14 days. So I have been left with no food whatsoever as well as no fridge. I have two kids and cant even buy shopping for my son to take to school. And now Im being told that I had 9 months left on the warranty for the fridge that died and that’s all I will get on a new fridge. Should I not receive a new warranty for a new fridge? And should they replace my food? Could really do with some feedback on this matter. Please help me.

I bought the Whirlpool Duet front load washing machine. It was a piece of junk and I bought it 3 years ago. Sounds like a jet taking off during spin cycle and drain.Well, let me tell you, its terrible. It walks out of the space its in during spin all the time and the F Codes. Im done! Just replaced the pump and motor for the drain on the thing and unplugged it several times to reset it. Still is giving me F codes.Im done, I tell you! Done! This has been going on since we bought it!

The cabrio washer that we purchased in 2010 did a good job of cleaning the clothes but the case started rusting within 6 months. After service calls and e-mails and phone calls, there have been no helpful suggestions beyond buy a complete new case. I hesitate to do that because I am convinced there is a design flaw in the area where the soap dispenser is located which allows the soap to flow between the case and the drum and it eats away theinside of the case through the inadequate paint covering on the outside of the case. It is a mess. Now the instruction panel is bubbling and lifting. I carefully care for my equipment and have kept two washers over 15 years and they still were in good shape with cases still looking new. This is not something I am doing wrong. It is a piece of junk with a terrible paint job and it cost more than any washer I have ever had. I wish I had some recourse. I am on a fixed income and had hoped this would be the last washer I would have to buy. I have photos.

The unit had all the features that we wanted and considered essential. The unit only weak issues is temperature(s) in both sections. The freezer is very poor with ice build up on the food stored for more than a couple of days. The manufacturer has been very weak in support as to how to solve this problem.

I purchased a home that came with Whirlpool appliances. I begged the company for GE or Maytag. Of course they went with the cheapest they could find. I must admit the microwave gets very hot but the dishwasher is a piece of crap! The water doesnt get hot and the dryer doesnt work. They tried to tell me it NEEDED Jet-Dry. I own 4 homes and have lived in all of them. Ive NEVER used Jet-Dry and all the others work perfectly. Run as far as you can from Whirlpool!