My front load washer doesn’t get my clothes clean. I have to rinse twice and still there is soap in my towels and they smell bad. I’ve followed all the tips without much luck. Now I use only Oxyclean and rinse with 1/4-1/8 c vinegar. The machine doesn’t pump all of the water out of the machine either. To me it is low-efficiency!

I purchased a front loader Whirlpool Cabrio washer/dryer in June of 2011. I was sold an extended warranty which ends June 30 of this year. I have made 4 calls to the Co which warranties the washer because it is making squeaking noises on the spin cycle. I was refused service because the customer service rep didnt “hear” anything. I finally had a local service Co check out the machine and was told the motor needs to be replaced and if under warranty I should demand it be replaced. I called again and still cannot get NSI to come out and see the problem.

Bought fridge in 2010, I am about to replace the icemaker for the 2nd time at a cost of over $300 each time by a Whirlpool authorized repair tech. No kids in the house and very limited use of icemaker. Motor keeps burning out because of the design flaw per the tech. Very poor design for a $1,500 fridge. Due to these issues I do not intend on purchasing Whirlpool products in the future.

This is the worst washing machine Ive ever purchased. Bought 12/19. The water level never never goes up high enough, to cover the cloths. I have to add water no matter what setting. I hate that. The sensor isnt working. You arent able to adjust it yourself, its computerized. The water shuts off when you lift the lid so you cant rinse out the soap or fabric softener caps. I hate that. The lid locks when the rinse cycle starts so I have to unlock the lid to add fabric softener. Why lock the lid so soon, wait till its in spinning mode. Really really badly designed!!!! Will never buy anything by Whirlpool ever again!

I called customer service because my pilot light would not stay lit on my 2005 Whirlpool water heater. I was told that I needed to install the upgrade kit and that the water heater was malfunctioning because of a lack of air and that it needed to be cleaned at the bottom. I paid for the shipping of the kit although I believe it is called an upgrade or conversion kit versus a recall for this water heater to save money and to get the consumer to pay for replacing defective parts. A certified technician installed the kit but the pilot light would not remain lit. He replaced the thermocouple, although new parts had just been received. This did not help either. The technician and I called customer service, which didnt resolve the issue. I also asked for a manager who would only agree to send out another conversion kit. There are three years remaining on the warranty but I am being told to keep replacing new parts with new parts until it works. That is unacceptable. Also, I was not informed that my problem is a recurring problem with this Whirlpool water heater that I purchased at Lowes.

After 14 years of good service with Whirlpool Duet front load washer dryer set, wife chose Whirlpool kitchen appliances as part of a kitchen update project. All matching fridge, range, microwave hood and dishwasher. What a nightmare! The icemaker growls and whines all the time and the dishwasher was broken before being packaged at the manufacturer. A wheel from the middle rack was missing when the dishwasher was opened. It wasnt in the sealed dishwasher nor in the box. So it had to have been broken off before the item was boxed. We called for warranty claim and A-1 Appliance was recommended out of Shreveport, LA. In a few weeks he showed up, looked at the rack for a while and said Ill have to order a new part. I said fine. (How hard can that be? Right?) So here we are 5 months later, unable to use the middle rack because it cant hold any weight with the roller missing. Multiple calls to Whirlpool and A1 and we keep getting promises and runarounds that turn out to be lies. How hard is it to say go to your local Lowes and well authorize them to give to give you a rack from an in-stock dishwasher? Let Lowes wait on the new part! Sounds simple, and any other company would have done that, or told us to return it to Lowes for another one. But NO! Whirlpool just whines about being behind on parts, shorthanded, or lies about the part is in and its A1s problem now.So, today, same story. A1 says they need 2 parts. **! Its one part. Whirlpool says A1 has the needed part. Same old runaround. So, we just replaced our 14 year old washer and dryer with NON Whirlpool units. $2500 more in of appliances that Whirlpool could have gotten, but Im guessing they dont even care about missing and losing sells. They certainly do not care about warranty, parts, quality, customer satisfaction or repeat customers. Never again with Whirlpool! Beware!

I have had a Whirlpool washer for less than 1 year and have had it serviced over 7 times with drain problems - code A10 being displayed. Have not been able to resolve the problem with neither the dealer nor the manufacturer. What a lemon!

In remodeling a house, we got all Whirlpool appliances for the kitchen, right when the lockdown started our freezer went out, 8 visits later from a local repair person, Whirpool will not honor the warranty and get us a new fridge!!! They just want the repair guy to keep replacing all the parts he has already replaced, the repair guy is beyond frustrated with Whirlpool and their crap!!! Never again, totally lost a customer here.

We purchased a Whirlpool Cabrio Washer Model WTW7340XW0 type 580 Serial C02770464 and a Whirlpool Cabrio Dryer Model WED7300XW0 Type DSSA-ELE-2406026-EL54 Ser M02717021 in 2010 for over $1,700. Included was a 3-yr anything goes wrong, well replace for free warranty. A month after the purchase, we lost our home and were forced to move. We put the new appliances in storage and they have been there ever since. From the day we purchased the washer, we never got a clean wash out of it. It seemed it used about a teaspoon of water. Clothes were never clean... We had many other problems at the time and both washer and dryer were put into storage.Today, the warranty has long expired and I happened to check on the ConsumerAffairs site to see if there were any comments regarding whirlpool Cabrio washers... WOW! 1600 negative comments and not one positive. Later, I realize we made a $1700 mistake. My question is do I have any recourse? Please advise.

I purchased a Whirlpool over the range microwave (model #YWMH31017AS-1) in April 2013, and had it installed in August of same year. It worked fine up until November 2014 - just over one year later. Everything on it works, except for the most important feature - IT DOESNT HEAT ANYTHING UP. Doesnt matter how long you set the timer for - the contents come out stone cold! I called Whirlpools 1-800 number and was told that because I did not purchase the extended warranty, I was responsible for all parts and labor costs. I find this completely unacceptable! I have had cheap $70 microwaves that have lasted 15-20 years. I will never buy another Whirlpool product, and am telling everyone I know to do the same!

We bought a washer in Sept. 2014 and it was used for 4 months before we left and went south for the winter. When we came back in May, we started hearing a loud banging noise so we notified Whirlpool since we were still under warranty. They sent a repairman and he said he needed to take the washer in so he could repair it. They have sent the part out 3 times and they said it was chipped or cracked so another would need to be sent. This has been going on for 2 months that weve been without the washer and today we checked and supposedly another part should be coming. They tell us our warranty is only for parts and labor not replacement. Help would be appreciated. Thank you.

I had a 6 year warranty on the new Water heater and about only 4 years into it the tank began leaking. Whirlpool replaced it but of course I was responsible for Parts and labor to replace it. The replacement only lasted just over only 2 years and just outside the total of 6 years from original purchase date on the first. Whirlpool refused to discuss it since it was a few months out of warranty. If someone else has purchased this heater it would have failed at 2 years and they would have had to warranty it anyway. I will never own another Whirlpool appliance because of their substandard products and warranty. I only wish I had reviewed the reviews of others and taken their experiences into consideration and not purchased Whirlpool. I am now out for another heater and reinstallation charges again.

Purchased a Whirlpool Cabrio Washer a few years back... Started getting F1 error message and just proceeded thru it like most did initially, but now has become pain in the rear just to do one load of laundry as we get the error 2-3 times when we start each load - then on every load w/ 21 minutes left on the cycle. From the looks of things online this is a chronic problem and should be fixed by manufacturer. I called Whirlpool customer service and first person I talked with said they understand it is an issue but no longer are any recalls or reworks on that machine. I asked to speak w/ supervisor and sat on hold until I got one. Was then informed they do know it was a problem but was not something they could do anything about other than schedule a service company to come take a look. I specifically asked if there was at one time a recall or if they were fixing this issue for a while. She said Yes, they took care of some of their customers but are no longer doing that for this model. So basically because I didnt call in at the right time I need to fix my machine myself. I said it will be the last Whirlpool or Whirlpool associated appliance I ever purchase if this is the kind of customer service I can expect... The supervisor just said she was sorry to hear that and to have a nice day. Hopefully enough people read these reviews as I wish I would have before purchasing my Cabrio and dont buy Whirlpool.

The knob on the Gas Cook top stove from Whirlpool (Part no: W10594481) is very poorly designed. It is very flimsy and breaks easily inside. Outside it still looks intact, but if you examine it on the reverse side, where it actually fits into the cooktops metal rod to turn the gas up or down, we can see it breaks there, as it is made of very cheap plastic. Although it is supposed to be a Stainless steel knob, it is actually all plastic where it matters most. I bought the new cook top from Whirlpool in 2014 and within a year have replaced all the knobs as they were breaking once every couple of months. I am still having this problem after 2 years now. I have contacted Whirlpool and have asked for a solution to this problem. They dont have any, other than offering a new version of the knob which costs $10 more and it is not easily available anywhere. I feel very cheated that I got a poor quality product and no help from them on fixing the problem.

I exchanged my fancy front loader Cabrio washing machine for a top loader after having numerous issues: clothes werent getting clean, extended water cycle, and a leak. The original purchase was made at Lowes, where I elected to invest in the 3 yr extended warranty plan. After several visits from their sub-contractor, they allowed me to exchange the washer for a top loader Whirlpool Cabrio. At first the washer seemed to work, but after about 8 months I started having problems. The bearings went out and when the service company replaced it they forgot to screw top of the machine together. During my first load, I heard this terrible noise and discovered that the entire top of the machine had separated from the bottom by 2 inches. I frantically rushed to turn the washer off before my laundry room flooded. So, they were out again and screwed the machine back together but failed to retrieve the original screw that they removed from the washer during the first round. Well, the screw got lodged in-between the drum and interior, causing it to completely break the machine. Lowes agreed to exchange the washer for another top loader Cabrio, but my 3 year service contract would not cover the new washer. Not to my surprise, I immediately had issues with it and had to hire a repairman to assess the problem, who concluded that it was the bearings. He informed me that it would be about $700 to replace the bearings and cheaper to just buy a new machine. I called Whirlpool and explained to them about all my issues, now becoming almost comical. They arranged for an outside contractor to assess it. After confirming that the bearing were bad they replaced them. Another few months go by before problems occur, this time the washing machine stopped draining water and spinning. The service company was out another 4 times. They replaced things like the mother board and control panel. My last appointment was today, where the service guy said, There is only one error code. It is a stuck button. I said, Will you at least witness a full cycle so I can show you all my problems: clothes still dirty and stinky, items still wet after spin cycle, cycle taking 2 to 3 hours to run, horrible noises, and timer adding minutes to original cycle. He called Whirlpool because he genuinely felt sorry for my situation. They were of no help. He didnt stay to witness a cycle. Moral of story: if the error code doesnt detect a problem, the consumer will not be helped (this is something that consumers do not have access to). They will happily call a technician out to put a bandaid on an issue until your warranty runs out. I have had between 7 to 10 service calls out to my house, requiring me to take either an entire or 1/2 day off of work each time. If I added up all time lost at work, I could have easily purchased a top-of-the-line washer/dryer duo and been done with all this Whirlpool foolishness. Do yourself a favor, stay away from this product.

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

Does everything its supposed to except get the clothes clean! Nothing gets clean, even on bulky setting when theres supposed to be more water in the machine!

Whirlpool Cabrio - What a nightmare. One year in… from the beginning the washer completes a cycle without attention. It gets stuck in a rinse cycle and eventually stops with an FF error display. Because of this it wastes HUGE quantities of water and takes far too long to actually wash clothes. It is so frustrating. We will buy a new Bosch and THROW this way. We cant even pass it on to our grandchildren.

Purchase whirlpool washer model W2W4800xQ2 in Sept. 2012. Had problem with lid lock after warranty. Now lid lock does not work, takes 1/2 hour to start wash and does no spin. Called whirlpool and they will do nothing. Repair will be $200. I opt to just purchase new machine. This machine is one piece of garbage.

Whirlpool Model WDT920SADM0 Dishwasher. We built a new modular home so Abraham Builders ordered all my kitchen appliances in 2014. We did not move in and start using the appliances until June, 2016. Here is what happened during the first 6 months: 1) Would not dissolve dry soap or packets as there were still particles and plastic in the dispenser. 2) Dishes were not getting clean and were spotty. 3) Would not dry dishes, ever!!! 4) Parts would keep popping off as we would find them on the bottom or hanging down. 5) Final straw was this morning around 4 a.m. (12/4/16)... woke up to the smell of wire burning in the house and discovered it was coming from the dishwasher that we had put on delay wash that night and when we opened the door, smoke came out from inside!!Since it was past purchase warranty date, we had no warranty and the builder would not return any of my calls on any problems and the manufacturer of my house closed the factory. Needless to say, we now have to spend another $900+ for another dishwasher! Not happy at all about this Whirlpool model and would not recommend it.

I purchased a Whirlpool Duet washer and dryer set in 2008. The washer control panel lasted 3 years. Because I did not have an extended warranty, Whirlpool would not do anything to accommodate me, despite the exorbitant cost of this machine. I told them that I would never buy another Whirlpool product. It is now 2017, and I have not purchased any other product made by Whirlpool. I want to make sure that a company manufacturing expensive machines designed to break within only a few years of normal use, goes out of business. Spread the Word to everyone you know about Whirlpools garbage machines. Maybe if enough consumers purchase products from other manufacturers, Whirlpool will get the message that they need to manufacture quality, long lasting machines. Try Speed Queen instead.

I have a Whirlpool stove. Theres nothing but problems with the oven sensor. This is the 3rd time we have to replace it. It had problems ever since I bought and thats been 11 years ago. My Magic Chef lasted 13 years with no problems. I have a Whirlpool microwave that had a recall on it. Never buy Whirlpool!

Thank you EPA for requiring water limits on manufactures of washing machines. As a result, I am forced to use the deep water and extra rinse functions to get clothes half way clean. So much for saving water! This Whirlpool Cabrio machine cost way too much for such lousy results. Additionally, I have to purchase a special product and clean my machine every month or two. Ridiculous!! I yearn for the old days when I could wash my clothes and they would actually come out clean.

Whirlpool Duet $1300, in the past we had great service from other Whirlpool products. Just a more modern look and knowing it was a company we had used in the past with very little or no problems so we expected the same only with energy and water savings. We are energy aware and believe in conserving energy and water where we can. My wife wanted to stick with the brand that gave us good service in the past and chose one of their most conservative units on the market (I believe it was based mainly on looks). What burns me the most about this unit is its constant consumption of clothing, the repair guy found nothing askew with the unit and suggested smaller loads. So we reduced the load size smaller and smaller till we were washing each outfit separately and guess what, it still ate clothes, just chews them up.We lose about a hundred dollars a month in clothing. This washer tears holes and shreds clothing on almost every load, I have to put shirts and lighter clothes to the back of the washer then load the heavier blue jeans and such toward the front and hope they finish in the same position or something is ruined. The fabric becomes distressed, stretched, shredded or has holes, or any combination of the above. We have taken to going to a laundromat or sending clothes to the cleaners. These units are three years old and we are now looking for a replacement for the washer because the local service guy won’t even come out any more. This problem surfaced within a week of the first use of the machine and has remained steady, as we are retired and travel a lot we are not always using them so they are what I would term very lightly used.

We purchased a Whirlpool washer model WTW7500 in November of 2017. I found the clothes were not getting clean and also noticed that even after a full wash some parts of the clothing or sheets had dry spots! I checked all connections and called for service. As soon as the serviceman saw the machine he said, “yes, that’s a problem with those machines”. They are low water/water saving as per some American regulation and that’s what happens... you’re going to have to live with it. He also suggested running an extra rinse and using “deep water” function. I did this and it made very little difference except now a wash cycle for bedding is 104 minutes! Also, still had a big dry spot on my sheets!When I called again to Whirlpool they scheduled another repairman for a second opinion, turned out to be the same person with the same answers... I called Whirlpool again and was informed that my washing machine is working as designed! I argued that a washing machine is designed to wash and clean clothes so this one does not do what it is designed for... I spoke to the supervisor, she was actually just rude, also said I not had 30 days to make a complaint and I was outside of that, when I asked to speak to her supervisor she said there was no one above her although she denied being the owner of Whirlpool! (That’s my little joke). Anyway wish someone had warned me prior to this purchase.

My dishwasher is really a simple basic dishwasher. It is efficient and does a good job of cleaning. You can put many items in the top and bottom and the utensil basket can be moved for better cleaning or more room. If I had one complaint that would be that it is a bit too loud but other than that it is wonderful.

We purchased this model in July of 2019 and have had nothing but problems with it since. The design is really bad - if you set the temperature on the ideal setting, everything on the top shelf freezes solid. If you reduce the setting to the one below ideal, your freezer doesnt get cold enough to keep ice cream hard. The ice cubes are a little more than half the size of our last Whirlpool refrigerator and the unit is noisy. Weve had Whirlpool out to work on it 4 or 5 times in the first 6 months and twice weve had to throw away food due to the unit not cycling on and off properly. One of the technicians told us he spends a lot of time working on this particular model - evidently, it has a lot of issues. We are now using our old garage refrigerator while we try to get Lowes to give us a refund on this piece of junk.

I purchased a Whirlpool washer in 2010. It has started to rust. I called the customer services dept. They told me that there was nothing they could do about it because it was over a year old. I asked to be transferred to a supervisor. She told me the same thing. I told her that its not as if Im looking for a new washer. She said that there was nothing they could do; I had to pay for the repairs myself. I told her, After spending almost $1,000 on a washer, I have to pay for the repairs? She said, Yes, maam. I asked if I could speak to someone over her. She said that she had to take down my name and number and someone would call me back in 24 hrs ... from the management team.She asked for my number and not my name and said someone would be calling back. I told her, How are you going to forward the message without a name? Maam, Im sorry. Whats your name? I doubt if anyone will be calling me back. Whirlpool customer service sucks! They dont know how to treat their customers. Watch out for the warranty. What they call a warranty is not.

First, let me say we are so lucky and blessed to get home in time to prevent my home from burning. My Whirlpool range, model 4rf364pxk0, apparently decided to turn itself on (no one home) and grew hotter and hotter. It obviously burned out the thermostat because it was way hotter than cleaning mode. The key pad was melted and sagging inward the control panel warped, heat pouring from it. The racks and interior were glowing orange! My back splash tile blackened and cracked! The oven door locked! Oven hood ruined although it probably saved my cabinets! We hit the breaker! There was so much heat you could feel it on the outside of the exterior wall of the house 30 minutes later! The clean up to my kitchen has been horrible. Black soot and strange greasy film on everything and the stench has been toxic enough to give my husband a raw throat and myself a migraine! Oh and here is the ironic part - my husband was bringing me home from a hospital stay from high blood pressure! It would be almost comic if it wasnt so darn scary! Please, please address this issue before a more tragic story is posted! From looking at this site, it is obvious that there have been other incidence of your stoves turning themselves on and uncontrolled heat. I firmly believe another few minutes and our home would have been engulfed in flames. Now I will spend my weekend shopping for a new ceramic range, hood and tile!

Good washing machine for 3 year. 4th year onwards your repair cost starts increasing. I purchased machine for 24 k. Now my repairs costs are 25 k. Each time the service guy comes puts me a bill of 7 k and above. The complaints to Mr ** goes to deaf years as he never picks the call. Their visit charges also are more and never give warranty above 30 days. How will you feel when you have paid more money on services ce than the product. I have supporting hills for all.

Its just OK, the electric cook top heats up slowly, but once heated works OK. Oven is just average! Glass cooktop stains easily and shows some discoloration in places. The glass on the oven door is also discolored on the inside and not cleanable!

Bought Whirlpool Dishwasher MDf760SADMZ including protection plan in November 2015. Product did not last even four years --top and bottom racks began falling apart-- and drain motor went out causing near flood in my kitchen. Disappointed consumer.

I just purchased a new stove after using my old one for 15 years with the same great quality. Its the brand I will purchase when I have my retirement home built next year and leave my new one in the home for my son so he wont have to buy one for 15/20 years.

It has plenty of room. The compartments within the refrigerator are well organized. There is plenty of room in the freezer. Have had this for about eight years and going strong.

Whirlpool fridge (model no ETILFKXKS) - I purchased this fridge from a very good dealer (Trail Appliances, Edmonton). Within a year, I had my first of the frozen water drain from top freezer to water pan. Of course, I blamed myself - too much warm food, blah blah. Now this is happening more and more often. The fridge is kept at number 1 of 5 for coldness. All foods are left on counter to cool, but three times over my Christmas holidays this year when I swore I would throw this fridge in the garbage - the drain froze, water all over the fridge, food having to be removed and placed in other peoples fridges, blah blah. Now it did it again this weekend! There are only two living here. I work all day and no one even opens the fridge much and again this happened. Im really sad that such a faulty product (too much insulation hiding the drain pipe behind the fridge and it must be much too small in diameter; otherwise, it wouldnt freeze up). Talking about work. We have two fridges there with 50 people using them all day and they run perfectly for the last 8 years that I have been there. So I think it indicates that my fridge is faulty. Im so sad too because I dont have the money for a new one. I just turned 65 and am about to retire (single mom). You would think that a $1,300 fridge would last longer than 6 years!

Whirlpool oven aqua lift - This oven is the worst in the world. I cant even imagine cooking a turkey in it. After cooking a pizza it took four cleanings and a lot of scrubbing. Self cleaning --- not, you clean and clean and clean. I have had ovens that were not self cleaning and easier to clean than this. Do not buy. And Lowes is no help at all. Run as fast as you can.

They are good washers but they are overpriced. They have way too many functions for doing laundry. I know everyone wants their washer to do it all but the machines just can’t. There is no washing machine in the world that can sense a stain and pinpoint it and remove it.

I recently purchased a new Whirlpool propane water heater. Dependable name, dependable product, years of trusted service, right?! We have bought many Whirlpool products over the years but never again. Got it home and installed it. It sounded like a plane taking off, and that was in the garage. Next came the lack of hot water. Mind you, we replaced a 40-gallon tank with a 40-gallon tank and the last one we had lasted 18 years without a problem.Well, same showers as usual, and we were turning up the heat mid-shower and again and again during the shower. Even turning up the heat on the water heater didnt relieve the problem. We are not happy with the product. And, no, there is nothing mechanically wrong with it; its just sub-par. Our water heater from 18 years ago worked more efficiently than this newer model. We called customer service, and we were told that unless there was something mechanically wrong with it, such as a defect, there was nothing we could do. There’s simply no recourse.Shame on Whirlpool for not making a quality product and standing behind it. This was a very expensive purchase - over $500.00. We thought we were buying a quality appliance. Very disappointed, and I will be returning it. I’m never buying another Whirlpool product again. I can only hope that the company we bought it from has a better customer service policy. Very frustrated and disappointed.

Bought this model #WTW8500DC from Lowes in 2015. Ever since had problems. Stopping in the middle, not starting, recently keeps running water, lid lock issues, had multiple service calls and multiple hardware changes, paid extra for extended warranty from Whirlpool hoping that within a year all problems would be gone after so many repairs. Boys I was wrong. After spending around $1200 between this machine and the extended warranty, three year later after the warranty expired now I am stuck with this non-functional piece of junk and looking for another washing machine. Would love to hear from Whirlpool if I stumbled upon a lemon, or three year is expected life of their $1000 plus machines.

I purchased a Whirlpool water heater on 9/30/2011. It is leaking at the point of cold water entry and is spewing a brown colored watery substance, leaking on the floor.

I purchased a Whirlpool Gold top freezer refrigerator (G2IXEFMWQ03) in May 2011. Six months later, the freezer began to collect frost and eventually clogged the refrigerator port from freezer. Since cold air from the freezer was not going to fridge, I had to turn down the refrigerator temp to lowest setting. I had a service person come out and replace Adaptive Defrost Control under warranty - it would have cost me around $250. Now roughly 12 months after repair, the defrost issue is back. The part cost me $175, and that is if I install it myself. I called and mailed Whirlpool which was a waste of time. This is the last Whirlpool I plan to purchase. For the same issue to occur in this short time span, it has engineering flaw written all over it.

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

I have enjoyed my stove for 16 yrs, it is very reliable and easy to use. The heating elements work well and heats up quickly. During this time I have not had any repair done. The areas of improvement that needs to be implemented is the inter glass that is installed at the front looking into the oven. In order to clean you have to take the front door off which is very difficult to put back together.

We purchased this Whirlpool pair after our upright machine was unable to be repaired... because of parts coming from China and being hard, if not, impossible to get. We have had this pair for about 2 years now (Lowe’s). It still doesnt clean the clothes and it continually goes off balance when doing sheets, comforters etc. Myself I feel since they have taken the middle agitator out of the machine - it no longer performs the way a washer should and that its main function is to get the clothes clean! I did write a letter to Whirlpool about it and they pretty much told me, “Well too bad.” So much for buying American made products... at least the upright did last 6 years!

Our Whirlpool Duet Washer started sounding like a jet engine 13 months after purchase. We spent $800 on a washer and it started to get very loud during spin cycle. After reading several reviews online with other people describing the same problem, figured it was the bearings. $800 to do my laundry for 13 months kind of crazy right. It would have cost almost $300 for the extended warranty through Whirlpool. In order to have it repaired, the cost would be around $600 because the drum and bearings need to be replaced at this point. Whirlpool’s customer service was no help and pretended they had never heard of this problem. However, reading reviews online tells me otherwise. I can buy a new Samsung on sale for $623, so that is the route we will probably take. We feel extremely cheated by what was once a well-known, reputable company. We will not buy Whirlpool/Maytag again until they put more emphasis on quality products with a cost efficient, longer duration warranty plan.

We purchased a brand new home with a brand new Whirlpool microwave in it. It was a combo, over the range/hood vent, model WMH1162XVB-0. Every now and again, sparks fly when preparing vegetables. Three times a repairman came to our home with no results. Each time, the problem persisted, with no improvement. On the first visit, the diagnosis was that we did not know how to properly use a microwave. It was noted that they gave us operating instructions and a personal tutorial to solve the problem.On the 2nd visit, we were instructed to buy a protective cover for our bowls when using the microwave. I asked if this would solve the problem, and was told no, but at least we wouldnt see it. This time, the random sparks happened in front of the repair man. He responded that it was the high iron content in the corn and peas that would ignite the sparks. Also, he said we needed to thaw everything before putting it in the microwave. Again, our issue was listed as consumer-use error and nothing was done.On the 3rd visit, we explained that we could not use the microwave on any setting higher than 70 for risking of sparks flying. We showed him the cover we were using, and the permanent marks being left by sparks. Again, the serviceman witnessed the sparks flying, even on thawed peas and corn that simply needed to be heated. He responded that by adjusting the power, and using the cover, we were obviously learning how to work the microwave and informed us that the next service call for this issue would be at our expense. There was nothing they would do for us, as the problem was our fault, not theirs. We explained that other neighbors with the same microwaves are not having this trouble, and we felt it was simply a faulty unit. He didnt seem to agree, nor care what we felt.I have been using microwaves daily for over 20 years. Our neighbors, having the same exact model, have had no issues at all. I know this is simply a faulty unit, and feel endangered each time I use the microwave. Whats even worse is the way Whirlpool has handled our situation. Our microwave is now 4 years old, and I have learned to rely on my toaster oven. When people visit, we have to caution them on the microwave. I will never buy any Whirlpool appliance for my home again. I do not trust the quality of their products or their service.

This machine needs to go back to the engineering dept. There are too many engineering defects to mention. My Cabrio washer and dryer was delivered October 11th of 2017. It is just my husband and myself so laundry was scarce. I have been unhappy with the washer since the beginning and just recently decided to try and solve the problem. I contacted Whirlpool first and was told these machines have great reviews and nothing is wrong with them. When I started describing the flaws, there was one excuse after another and the person from Whirlpool blew me off. The flaws... all begin with not cleaning which is caused by design. The water level, even with the deep water setting, does not even cover the amount of clothes in a small load; the agitator is so small, there is no effect on agitating the clothes; even with using a SMALL amount of HD detergent, there is always soap residue on the clothes because of the lack of water; and last issue but not final is the load going off balance. The machine will walk all over and error codes according to the repairman need to be cleared so must call if it happened again. Well, the very next load it went off balance again. I did not call because I would have the repairman living with us and I am not willing to set up a bedroom for him or feed him. So, Whirlpool does not care if their product needs redesigning, they only care about selling their product and then the consumer is on their own. Basically the same train of thought from Best Buy where we purchased the machines. Best Buy would be happy to sell me another laundry set... per the store manager but that is all he could do. Will I purchase from Best Buy again... I think you know the answer to that. If they cannot stand behind a product they sell, then they can keep everything they sell, no more money coming from my checkbook to them ever again. Someone, whether the manufacturer or the retailer, should be willing to stand behind their product. But, no one cares. Bottomline, do not believe the ratings on the Cabrio washer. This machine has design flaws that cannot be corrected.

I bought a Whirlpool water heater in 2009. I paid $588.46 at Lowes. Turns out it is in a class action lawsuit for faulty thermocouple. I was given a coupon from Whirlpool for 2 new thermocouples as part of the class action lawsuit. The thermocouple goes out on it every 1-3 months. You never know when youre going to have a cold shower getting ready for work in the morning. I literally could have bought a new water heater for what Ive spent on thermocouples the last few years. The last two times it went out, I had to replace it twice within 1 day. Im sick of replacing it and have decided to install a new hot water heater. I am disgusted with Whirlpool and tried to contact them about it but have gotten no response. I will never buy another Whirlpool product and would not recommend them to anyone!

Do not purchase (Whirlpool products). Discuss guarantees with salespeople when purchasing! They are total sham and in fact borderline fraud! Purchased $5,000 dollar KitchenAid fridge only to have it breakdown after only 8 months. What they dont tell you is instead of recalling a product they give their repair personnel whats called a notice which means they know there are issues with their products!After much discussion and trying to return the product to no avail, I was told very adamantly my fridge would need to break down another additional 2 times before my fridge would be replaced with a new fridge. Forget about the cost of your food inside the fridge, they dont care! Just beware that their warranties and parts and labour are a complete and utter joke! My advice after much research if you can afford it buy Miele or Subzero product. Its more expensive but a lot less headaches in the long run! Ive eaten the cost of my KitchenAid appliance and went with a Subzero fridge. Dont believe the higher pressure sales pitch from salesman. Youre best to call a repairman and ask what hes fixing more often than not and 9/10 times he will tell you Whirlpool product! Customer service is a complete circus and gong show. Youll get further ahead talking to a donkey!!! Buyer beware! Whirlpool Canada/USA is a joke!!! Dont say I didnt warn ya!!!

After reading all reviews online on the lid of the Whirlpool Cabrio Washer, it upsets me that there has not been a recall on this. Our lid has snapped & has to be held down until the lock light comes on. Often times during the cycle it must sense the lid is broken & thinks it is not locked & sets the load off line. I have to pause the load & then reset the load & hold the lid down tight until it restarts.

We purchased a Whirlpool Countertop Microwave (model MT4155) at HHGregg on 6/02/2012. (This was a replacement for another oven that failed after a couple of years - NOT a Whirlpool.) On 6/04/2013, i.e., 2 days past the standard 1 yr warranty expiration, the oven went nuts. I was cooking a plateful of baked potatoes on the auto setting. When the potatoes were done, I opened the door to take them out and the oven started to run! WITH the door open! When I shut the door, it stopped. So the only way to get the oven to operate was to OPEN the door. I dont think this is a safe or effective practice. Knowing it was two days past the warranty, I called customer service anyway just to see what they would say. To my surprise, they (I talked to two different people) were VERY pleasant and accommodating, and offered to cover the cost of repairs and even set up an appointment for the authorized repair person, and then called to verify the appt. as well. Great! I was impressed!The repairman showed up as scheduled and seemed puzzled at first, but he dismantled the outside cabinet and determined the fault was in the door switch. He wasnt sure he had a replacement with him, but he did find one, put the new part in the oven, and re-assembled everything. We made sure it worked and he then left. Fast forward 5.5 months, when again I was cooking potatoes (boiled this time. Maybe the oven doesnt like potatoes!). I had the timer set for 20 minutes on 100%. I was out of the room when it quit cooking, but I think it ran for about 6 minutes and then just shut off and could not be persuaded to restart. The clock continued to count down, and all the other bells and whistles still functioned - it just wouldnt cook. Major hassle. The following day, I was looking at it, messing around to see if I could figure out what was wrong, and discovered that if I pushed on the door latch just a little, the oven would run. Well, thats a nifty workaround, as long as you arent doing any more than briefly reheating something, but not so great if you are actually trying to cook something. I continued to do this for the next few days and then suddenly one night it reverted to the first bad behavior - only running when the door was open. I was able to get that to stop, but the following day, it refused to work at all and it is now sitting here uselessly, just a little over 1.5 years old. I want to go buy another oven (and YES - a different brand!) - my SO wants to repair this one, again. After reading the experiences of others on this site, I REALLY cant see the point in repairing esp not if I have to pay this time (which I probably will), and also when it seems to be a faulty part/design causing this problem. I dont have the time or patience to deal with an unreliable appliance, esp one that I use often. I have not tried to call customer service yet, but Im not expecting great things, not this time. Planned obsolescence? Sure makes me wonder.

I have a new Duet Washer and it is a nightmare. It keeps throwing the same F8 E1 code. The repair people have replaced five parts and been out four times. I feel like I have been scammed out of $900. I will never purchase a Whirlpool again ever!

I wish I had read all these reviews before buying this junk/lemon of a machine. Havent had the machine for a year yet and lots of problems. Only can wash five towels at a time and thats pushing it. Decided I would deal with it, until it gave other problems. First sometimes skipped cycles, then water came in when it was spinning. Called for service. Checking to see if we even can get you service in your area, representative says.About a week later tech comes and puts two parts in and left. Happy to get laundry going but, guess what??? Washes only doesnt do anything else and trying desperately to drain water out. Of course I have to take clothes out and bring to laundry. Tech comes back next day. Now he cant get any cycles to work either. Fried, tech says. Sets me up for next Saturday, fine.Now get a call on Monday, not coming. Tuesday is next appointment. Apparently inventory representative says. Didnt know that before??? Call Whirlpool, service first, then company. I want a new one, this is definitely a lemon. Nope, tech will be there on Tuesday. I hope Whirlpool reads this. They should be ashamed of their company. They used to be good, always bought their products. Dont buy these machines, trust me you dont need the aggravation. Totally disgusted.

At some point, Whirlpool should accept the fact that they should not sell this machine. Word of mouth spreads fast! Im hoping it will make a big dent in sales because I know then they will listen and act! I purchased it in 2006 for $800, thinking this Cabrio 6400SW is a dream, I can get more done in less time (at that time, there were seven in our family). However, problems within the first year, F1, but I was happy and still under warranty! It was fixed, only to start the problem again. This time, not under warranty! I really wish I had said yes to the extended warranty! Even the repair guy Whirlpool sent suggested it may be a good thing to get the extended warranty if I were you! I think he was trying to tell me something!My naive thought was, why spend more money we did not have? After all, it is a new machine! I did not comprehend that any company could sell and continue to sell something that was clearly a defective machine! Nor did I entertain the thought that a company would not stand behind their product! It is now 2012, I still have the machine because we have dealt with it and have/had no extra money to throw out at it. I have dealt with F1 for several years and did not contact Whirlpool, mostly out of lack of time to research what the deal was and if others were experiencing the same. In November 2011, after reading many complaints and frustrations on the internet and what results they got, I called Whirlpool. Using a level head, sugar sweet persona and a mindset of disbelief that Whirlpool would allow such problems, the customer service girl did her best with what she was told to reply with (meaning, there is nothing she can do). It is then that you ask to speak with a manager or director. I won in getting a repair guy out to fix the F1. They made it sound like they were doing me a onetime favor. The machine board was replaced, the repair person also thought there was an obstruction in the hose and he could fix it, but it would cost us money and suggested we try our hand at it first. We did find an obstruction and for one week, the machine was quietly working beautifully! Whirlpool even called to see about how it was working and my husband had answered that everything works well, not knowing that Ld is our new problem. Ld had started to pop up at the end of that week.So here it is July and Im so frustrated trying to get wash done. Im thinking of all the wasted time, all the wasted electricity and energy Ive spent trying to get this machine to work! My kids are trained to hit stop/pause if they hear it beeping. Some days we cant even get the clothes to spin dry. I try different cycles to get the machine to start and often have to cancel the cycle and change it to another cycle to get the machine to continue. Is there a smell? Yes, and I run the clean washer cycle twice in a row just about every other week now. That doesnt even seem to clean the washer anymore! Tangled clothes sometimes. Ld always, uL sometimes and a sound like it is trying to do something but is stuck. Lots of laundry to do! No money to fix it! Whirlpool needs to stop selling an inferior machine! I know one thing. Never Whirlpool again and I tell everyone not to go with Whirlpool Cabrio. Even one of my co-workers had one and bought a new washer (not Whirlpool) because of problems with her Cabrio only after three years! Do not purchase a Cabrio!

I purchased a Whirlpool Cabrio Set from a local store. Just over a year later, the washer got very loud like a jet engine. Called the registered repairman, he came out took a look and said he would get back to me. Called him 3 times over 3 weeks, no show (Hoodland Appliance). Called someone else, repaired it for $400.00. Called Whirlpool, they are not interested. 2 years later now and the machine is getting loud again. This is due to the spin throws water up and it is able to get out of the tub and down into the barring and the soap residue wears the barring out. Bad design. Called Whirlpool again and again they are not interested but can put me in touch with a repairman. I will not repair again but will use until dies and buy something else not related to Whirlpool. So much for energy efficiency.

I have had our new Whirlpool Cabrio Washer for about a year. I absolutely hate it. I along with all the other people that is complaining about their Cabrio. I have found it to stain my clothes, not get them clean... Sometimes not even get part of them wet. I wash every load now no matter how small on the deep water option. I still have to add about 3 to 6 gals of water after it fills to try to help them get as clean as I possible can. I have stopped using fabric softener because I believe that is what may be leaving the stains on the clothes because it doesnt dilute it. Also you cant soak clothes in the washer long enough. I know it offers a presoak but when the clothes are not getting wet... That is not soaking. I tried to fill it up and raise the lid so it wouldnt wash until I was ready for it to wash but it automatically emptied the tub after a short time.It is funny watching the clothes when washing... Even I could tell they were not going to be washed well. I thought who in the world developed this washer. Certainly no one that had ever really considered what women need to wash clothes on a daily basis. I would sell it but I dont think anyone would buy it. If there is a class action suit I would consider joining in. Whirlpool could not have spent much effort in checking this washer out. A lot of money down the drain. I did not buy the dryer because of the lint vent being on top of it. What a mess those make when you have to empty it. So I purchased a Maytag Bravos XL. Now that is a wonderful dryer! As one homemaker to another I suggest you check it out. Never had one I liked more.

I love my Refrigerator. It is a side-by-side with ice-maker and water in the door. I have plenty of room in the refrigerator, and I really like the adjustable shelves. I would definitely purchase another Whirlpool (next time with freezer on the bottom). I love the Stainless and would probably purchase again - or depending on the kitchen maybe black.

Not cooling properly on wpf560smywc2 French door - Milk only last 3 days. Temp wont stay consistent. 4 times out and say normal. Ice is forming on fan in freezer and back wall causing no flow in refrigerator but freezer cooling. Only 3 months old. Lowes Service Advantage (Extended Warranty) nor Whirlpool will replace or do anything about it. Was told 3 times out and replacement then today they sent me email with their policy or 3 times out with a repair (Parts must be changed) wait 30 days then another repair etc. then on 4th repair will replace. Lied to buy sales and called liar by repair guy when he told Whirlpool nothing wrong. I just wanted a new one cause I didnt like features. Lowes has a return policy which has in fine print only 30 days for refrigerator so they wont help. Was told I have to do a food loss claim and they would email form. Still hasnt happen. Lied to and get a replacement or repair and cant afford another.

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

Have always loved Whirlpool. Like the silverware in the door. Doesnt take up space for other dishes. Cleans well and quiet. Trusted brand and would highly recommend Whirlpool. All of my appliances are Whirlpool, stove, refrigerator, washer and dryer. You might call me a diehard fan.

I purchased a new gas water heater and had it installed by a plumber. It worked for 3 weeks then we lost hot water. I called the 877 number and got shoveled around to 3 or 4 people. I got hung up on twice then spent 45 minutes repeating all the instructions that are on the tank to relight the pilot light. They agreed to send a new valve. The first time, I never received the valve (after 10 days) and had to call back. The second time I called in, I spent 20 minutes trying to get another valve sent. The valve I, finally, received had plumbers dope on the back and clearly was previously used. Had the original plumber replace the faulty valve? And lo and behold, the second valve didnt work either. I have no idea why a gas water heater would have any issues after 3 weeks. I bought it brand new from Lowe’s. It is obvious that Whirlpool makes shoddy products. They have very poor customer service and care little for the customers’ time either in correcting the problem or being without hot water. I have spent over 2 hours with Whirlpool. Only to 3 weeks after the initial call, I still do not have hot water from a heater that is less than 2 months old! I called them on the issue of the second valve not working and they put me on hold (after 10 minutes the line went dead and I was disconnected) despite the fact I asked them not to do that!

Had one double wall oven lasted 15 years with just about no problems until the control panel broke and could not be fixed. Bought another just like it and it is having problems after 6 months. Light wont work. Turn on from the control panel and the time does not work.

Never again will I buy a Whirlpool product. I paid over $800 for a new washer 51/2 years ago. I had it worked on twice under extended warranty. Now the bearings are out of the tub and it sounds like a jet taking off when it spins. I had whirlpool products in the past and they lasted for years with no problems. I have a friend who has a relative who is an engineer for whirlpool and his job is to engineer their products so they fail within a certain time frame. They dont want them to last like they use to. They now have gotten their product line to the point where they can tell when it will fail. This is crap. What happened to products that lasted like they use to. NEVER BUY WHIRLPOOL.

I Purchased a Whirlpool range with self cleaning. I do not recommend anyone to purchase these ranges. The self-cleaning does not work at all. Like numerous reviews that said you can run them several times to do the self cleaning and they do not clean at all. Save your money. Do not purchase a whirlpool appliance!

We bought a top loaded Whirlpool washer, model WTW5000DW2 last May from Lowe’s for a summer beach cottage. It has been a terrible experience. There was a 30 day warranty from Lowe’s which unfortunately we missed because we had not moved down for the summer till after the 30 days. Working through Whirlpool, they sent an independent contractor out 5 times over the summer. Control panel was replaced twice. It never worked properly. I’m now back for the summer, and it still does not work. Do not buy this washer.

My Whirlpool washer is lasted 15 yrs and is very good at cleaning clothes, it is also easy join my water bill. I purchased mine at Home Depot. They also finance. I hope you enjoy your purchase. I know I do.

My WTW4900BWO failed after about 2 1/2 years. Out of warranty, but I called Whirlpool Customer Service and was initially delighted that they offered to sell me a repair warranty that would cover the repair of my broken transmission. Was told that through AIG Insurance, I would have a repairman at the house tomorrow to repair the washer. A few hours later, their contracted local repair service called to try to push appointment back a day but I refused since I was told my washer would be repaired tomorrow. They showed up the next day in a old faded van, diagnosed the problem and then told me they would have to get authorization and come back in 3-4 days. A couple of days later I received a voice mail from AIG saying that since the cost of repair was more than the cost of the premium, they were canceling my policy & would refund my money. So a week later I still had a broken machine and no solution other than buying a new one or paying the cost of a new one to repair. Moral of the story: Whirlpool builds unreliable washing machines (and water softeners) and their customer service will promise you a repair that may not happen. Dont buy Whirlpool, but if you feel compelled, you better buy an extended warranty and cross your fingers. That said, we always had purchased GE appliances and never had a problem.

The tub mounts of my 6 years old Whirlpool washer are broken. It’s too expensive to replace. Seems like built in obsolescence! Ive also had mold/odor issues. Finally, I know how to fix that, now this. I just want to warn others, these machines are not designed for the long haul.

This company should be avoided at all costs. Purchased 2 Whirlpool dishwashers in 2018 and in less than 2 year the top dish rack glide rail front wheel broke off causing the rack to drop down and render the dishwasher unusable. Warranty was one year and I went online only to notice that the OEM factory replacement part(s) are now made out of stainless steel (or aluminum). I also noted that the parts were made prior to 2015 (date on the video and other vendor sites) Which is a good 2 years prior to my purchasing of this product. This means that they obviously knew there was an issue but continued to produce and sell them with known faulty parts well after they realized at least 2 plus years when you consider that they would have had to re-tool, redesign and send to production prior to the product release date.So it looks like they have continued to sell the product knowing fully well they were defective and did so just to sell replacement parts or to use up existing parts inventory. Either way this means this company has no scruples and does not stand behind their product. Another stain on the reputation of products made in China! Shame on you Whirlpool!

The washer was 5 months old and broke. Three service appointments and multiple phone calls, it still wasn’t fixed. Whirlpool sent rusty parts out to my home and that was the second excuse for not fixing the washer. The poor service guy must have been 70 years old. Hello, how do washer parts get rusty when they are not even used and are kept in a box?

A whirlpool water heater model FG1F5040T3 purchased from Lowes five years ago developed problems, which could not be fixed. My problems started two weeks ago when the pilot light would not stay lit eight hours at a time and then nothing. Having a service plan through our utilities, they were notified not once but as it stands now, 6 times. Six techs have been out to my house and replaced the thermocouple twice and a complete gas control valve. The pilot still will not stay lit. Supervisor contacted Whirlpool on Thursday. Now its Saturday and no word from Whirlpool and no hot water. Try to get assistance from Whirlpool after work hours and it is impossible. This tells me that they do not care about their customer or the product that they make. Do not buy Whirlpool products!

I purchased my Whirlpool refrigerator in March of 2011 and the ice dispenser failed in early April of 2012. I called Whirlpool and asked for a repair, but they refused, saying the refrigerator was out of warranty. Being a handy person and upset about the failure after only just over a year, I took the dispenser apart and found that a plastic part had broken and caused the ice door to become unhinged. I called Whirlpool back and explained what had happened, but they refused to help again. They transferred me to the parts department where I was told that the part that was broken was not available and the only thing I could do was replace the entire door! Not only is their product poorly designed, but it is also not easily repaired. I will never buy another Whirlpool appliance.

I had this same refrigerator in another home and had no issues, this particular one now I have nothing but issues with it. It seems that the quality is not consistent. First the ice maker was not working, then the freezer light burned out and now there is extensive frost build up in the freezer. The refrigerator is only 2 years old!

I bought the Whirlpool Cabrio model # wtw5500xw2 about two 1/2 years ago. Besides my clothes not clean, I havent have any problems with it until recently. Usually it doesnt spin. The clothes are left soak and wet. First the belt broke, then the lid lock, then the nut came off the pulley, then the splutch assembly. There was a few more problems in there. Now who knows what is wrong with it? It is one problem after another. It is a money trap. The CEO was just after money. There needs to be one big lawsuit against Whirlpool. After I find out what is wrong with it and the cost to fix it, I probably will just go buy a new washer/dryer set. And it will NOT be a Whirlpool.

I purchased the Whirlpool Cabrio HE top loading washer and front-loading dryer about 7 years ago. It has been okay, but nothing special. Recently it began stopping in the middle of the cycle and showing an F51 error. Then all of a sudden the noise during spin was deafening. Brought out a tech, who came and did some eval. Left with some basic maintenance. Did a load, and happily no more F51 code, but still so very loud during spin cycle.Called again; tech returned and said that drum and shaft would likely need to be replaced to the tune of some $500. The same story as others have told. We should have bought the extended warranty. Like others, I also felt that washers lasted at least 10 years. And that seemed a short time given expectations in the past of 20 years of service. Im disappointed in Whirlpool. Even though Consumer Reports gives the Whirlpool Duet washer (new 2013) one of its highest reviews, I cant bring myself to buy another Whirlpool product. It appears to me that this warrants recall as well.

We have the Cabrio model and are thoroughly pleased with the performance. My only issue is the amount of sounds during the spin cycle. Otherwise, the machine is quiet. I like having the automatic dispensers for soap, bleach and fabric softener. Not having the classic tub makes loading a little different as the clothes need to be distributed around the side of the tub and avoid the center.

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

After owning the highly recommended Cabrio for only 2 years, I was told it would cost $300 for the motherboard!! I have always used Whirlpool but this machine is terrible. Water saving is not an option when washing clothes. Unless I use the bulky cycle, my clothes come out dry and smell dirty.

Exterior metal reaches temperatures that cause minor burns on an adult finger and could be potentially more dangerous for a child. The self-clean feature has crashed the oven on two out of three uses of this function and overheats handle.

My Whirlpool microwave door started cracking little by little. Pieces started falling off. My warranty company stated it was cosmetics, so my warranty did not cover it. Finally, the whole door came off. The warranty company finally agreed to replace the door. Less then a month after replacing the door, part of the handle cracked off. There must be some sort of defect in the plastic used to make these doors, and if so, there should be a recall.

I have a Whirlpool Gas Water Heater, product #0733136, that was installed in 2010. The pilot has repeatedly gone out and had to be re-lit. After reading some of the comments, I am amazed that other people were told to verify gas supply with the gas company (done) and clean the air intake (done) and then to call customer service and be told to do the intake cleaning again (done professionally six days ago). I will never buy another Whirlpool appliance, and fortunately, I am in property management and can advise others to avoid this company as well. I am extremely disappointed in Lowes for not doing a better job of providing reliable choices for their customers especially after these many complaints over the years. I have decided to replace the water heater with another brand immediately.

I bought my Whirlpool Cabrio washer from Lowes in Statesboro GA on 2-14-14. I did purchases an extended warranty on it. After 11 months is when I started to have my problems. I was washing my clothes. I did not hear my beep on my washer. After 2 hours my laundry should have been done. I stopped on the wash cycle and shut off. I put it on the rinse cycle thinking it washed my clothes. It shut off during the rinse cycle. I called the Lowes repair. ** was to come the next day, He did not show up. I had to call again. It took 2 more days before he came out.It takes over 6 business days before I get my part. I have to have my laundry washed else where. It did the same thing again. I called. ** came out. He ordered the other part. It took 7 business days. It came in Tuesday. I tried to wash my daughters comfort on Wednesday. It did the same thing. Shut off during the wash cycle. I called at once. ** was to have been here Thursday. He never showed up. I called Friday. They said hell be there by 5. He still never showed up. I called back today .This time ** called me. He said, “So you tore it up?” I said, “NO it’s still doing the same thing.” He said hell be here tomorrow between 8-12. I am so tired of this washer. I even asked if I could get a replacement. They said no. I said this is stressing me out. I am on anxiety pills already. This is not doing any good. I paid all the money for this washer and it does not work. I have to arrange to have my laundry done some where else. All they said was sorry.This is the worse washer to buy.

We bought a Cabrio washer model #WTW7300DW0 and are very unhappy. The clothes come out of the washer dirty, with chunks of soap, (yes we are using HE detergent) and patches of lint on them. The low water design is a joke. The clothes on the top of the load never get into the water. The lid needed repair from the first day we bought it. We have tried all the water settings and the clothes on the top barely move. Why hasnt Whirlpool figured out that this design is just not working? Our three month old washer is headed out of our house one way or another! Notice we didnt give it any stars!

We built a new home at the beach to enjoy our retirement and the builder installed new Whirlpool appliances. As far as we are concerned this was the BIGGEST WASTE OF MONEY WE HAD. Our appliances were under warranty for 1 year as usual and after 14 months things began to break. The latest is the ice maker in the French door fridge. After finding the diagnostics test online I ran the test and determined that the whole ice maker needs replaced. This ridiculous since the fridge is only a little over a year old. We even upgraded the fridge to avoid any problems. After talking to the people in our neighborhood we have come to find out that most people here have had trouble with whirlpool appliances.. I am ready to send these to the junkyard and replace them with a reputable brand (LG) that we owned before and were very happy with.. I dont understand if there is all these problems with Whirlpool products why the technical team doesnt fix the problem... Get parts from the USA NOT CHINA!!! My neighbor just told me he had the repairman at his house 7 times to fix his fridge and finally got a new one. Just got tired of the hassle and expense....

Whirlpool Dishwasher MOD#WDT970SAHZ0. I have to wash the dish before it goes in otherwise it doesn’t get food or anything off. It DOES NOT DRY at all. Even when I add the heat extended dry button. The normal setting takes 3 hrs & 12min to run & again, doesnt really wash & for sure doesnt dry. I have added jet dry. I called and they keep telling me it should have more jet dry! Ugh! I now have rust happening because it doesn’t dry. DO NOT BUY THIS MODEL.

Whirlpool Washer WTW8700EC + Dryer WGD8700EC. Bought to replace a 35-year-old Whirlpool set that is still working and had no repairs in that 35 years of ownership. Gave to family member and its working well. Was not a cheap item but well worth the money. It performs beautifully. I chose Whirlpool. It is a proven brand with a long history of reliability. When I bought my last Whirlpool, I bought the top of the line model washer and dryer. They say you get what you pay for and that holds true in my case as has with many others who believe it! So this time I did the same thing and bought the best top loader they had. It has many options I still need to learn. I just use it like the old machine and dont need to worry about types of fabrics or making mistakes. Just follow the instructions for detergent and softeners and all is good. This machine cleans as great as the old one without beating the clothes to death. New agitator design keeps from paddling the clothes, so I dont need to use the gentle cycle or medium to preserve the clothes. The dryer I can say is most efficient as I noticed it took far less time to dry, and notice a small drop in my electric bill and gas bill. I think this will be my last machine ever needed. I do take care of my things and I do clean and polish my machines, they are an investment like a car or house. Front loaders have a lot of problems with leaks from the doors. Will stick with top load only!

Purchased a Whirlpool double oven (WGE745COFH) in September 2018. It is now May 2019. After 5 service technicians verified the erratic temperature fluctuations in the ovens, Whirlpool insists that a +25 degree to -25 degree fluctuation in a heating cycle is normal. The motherboard was changed 3 times, and the sensors were changed 3 times, including hard-wiring the last set of sensors. I called Whirlpool and customer service says that is normal. Ever tried baking at a 350 degree setting that fluctuates from 375 degrees down to 312 degrees while trying to maintain a 350 degree setting? I understand there has to be some fluctuation, but either it took a lot of extra time or burned my food consistently. Ridiculous.So, with the help of wonderful people at Lowes (where I purchased the double oven) Whirlpool is refunding my money and Lowes has taken back the slide-in double oven. In my quest to replace it, multiple appliance sellers have told me that all the new ovens having motherboards and sensors have big fluctuations in the oven heating cycles. I find that unacceptable. My husband and other family members have worked daily in an industry where temperatures were critical. They used ovens that could maintain temperature within 5 degrees of set temperature with analog controls. The home consumers are being ripped off with cheap, sub-standard parts making throw away appliances and getting away with it. What do I buy? Havent figured that out yet, but have purchased a countertop toaster oven that bakes beautifully.

Purchased front load washer & dryer 2009 - have had issues with the washer ever since. The last episode has taken 3 visits from repairman - they cant figure out what the problem is - wont finish a cycle (any of them) and locks up. Cant open the door without turning it off and then back on. But the load wont spin dry - leaves clothes wet. Already had the harness replaced a couple of years ago and now they replaced the flywheel (it was warped) thinking that was the problem. Nope. Still wont work & the repair company said they cant figure it out & neither can Whirlpool. Im very angry after reading all of these posts about Whirlpool. Not a happy customer. But what can you do???

I Bought the Whirlpool Duet Steam Mod#: WFW95HEDC0 in 2015. I have always wondered how a machine can get clothes clean with less water but liked the idea of the energy star and saving water. However, I found that I was right and the clothes do not get very clean. They do not even get all wet hence the dry feeling when they are done. I just recently got a little frustrated at having to rewash some things by hand afterwards. I started to pretreat and wash out stains by hand beforehand. That helped some. I finally stopped the machine after all the water was done filling it and it tumbled a bit. It looked like it was wet from the window but when I dug through the clothes I pulled out a t-shirt that was almost bone dry. Some of the other thicker clothes like jeans etc. had a lot of dry spots too. This is why the odors don’t come out and why spots and lines are left where the dry meets the wet. There just isn’t enough water get all the material wet. I then proceeded to pour a pail of water in to get all the clothes wet. When I started it back up, it drained some of the water and I still had the problem. So now I get all the clothes wet in the sink before I put them in the washer. It’s amazing how clean they got and they didn’t have the body odors either. I think this machine would be fine if it could be reprogrammed to add more water for cycles. I know that would change the “Energy Star” but this water saving idea is bogus if we have to rewash and add more water to the cycles. At this point I will be looking for a new machine that doesn’t have the energy star but allows me to adjust the water myself. I do not trust these machines anymore.

This washer (Cabrio 6th Sense Washer) is less than 4 years old and now needs $500.00 worth of repair. You have to replace the tub in order to replace the bearings. If your washer starts to make noises during the spin cycle, you are in for a big repair bill. I still havent decided if I am going to repair it or junk it. The towels always smell sour even if you wash them twice.

Cabrio Whirlpool washer - I hate this washer. Had it for about 3 years now and it will not spin out and does not give a code. Called a service tech out and they cannot find anything wrong with it. The water goes out but will not spin. It sits on 20 minutes and does nothing. Will not buy another Whirlpool washer. Wanted a good washer and got a piece of junk. Will not recommend it to anyone else. Think Im going back to the old style.

I need to start by saying I or we, my wife and I are both disabled - her with a head injury and a prosthetic leg and walks with a cane and myself well Im stuck in a wheelchair, this makes grocery shopping more of a chore for us than most people and putting things away is part two for this chore. I figured Id buy the biggest, best (LOL) refrigerator Whirlpool had to offer, so I could do our grocery shopping once a month and have a place for everything and the fridge being so big would be capable of holding a months worth of food. It performs that function very well!The problem began when I purchased this wonderful piece of quality craftsmanship (cough) at Lowes in Denton Texas on 6/19/13. While one delivery guy stood on my sidewalk talking to me, we watched the one other guy bringing my rather large brand new Whirlpool refrigerator up the driveway with a regular (not an appliance) dolly. After getting to the end of the driveway and having to go through the front yard to get to the sidewalk, the monster fridge started leaning and eventually ended up on its side in the front yard, needless to say I was a little concerned about damage. They continued to get it in the house after providing me a nice gouge in the door frame before realizing it may be best to take the front door off before entry. So after getting it to the kitchen and removing the box we noticed the left door was way out of whack, so the delivery guy called his boss and we all agreed I needed a new refrigerator. A week later my second new refrigerator was delivered, no box around this one but it made it all the way into the kitchen without a hitch or any more scraps in the front door frame.Three months of dealing with water running down from the ice maker into the door storage areas I made my first service call, the guy said Whirlpool doesnt always put the correct thickness of gasket between the ice machine door and the ice bucket. He ordered gaskets and installed them the next week. Water continued to run down the door from the ice bucket to the shelf storage. 5/14/14 I called for another problem. The refrigerator seems to be running all the time, and there was a fan starting and stopping continuously as well. This was Miles Appliance - he seen the water running down the door and squirted a tube of sealer in the ice machine, replaced the little plastic fan and said that should fix it! I let the Whirlpool service scheduler talk me into the extended warranty since my one year warranty was about to expire so I bit and bought the warranty. 7/18/14 the fridge had a new sound going on for the last few days and still seems to be running all the time. I called for another warrant service, this time I drew In Home Appliance Repair. After waiting three days a guy comes out, verifies the fridge isnt cooling properly and tells me to unplug it for three days, so the ice ball that has formed somewhere can melt, that the noise I was hearing was a fan rubbing against the ice ball. So three more days go by and I plug in the fridge. Two days later the freezer has only cooled to 50 degrees. I called In Home Appliance Repair and they told me Id have to call into Assurant to make another service ticket, which I did. It takes two to three days for service tickets to get processes. After the second day, I called McNiels in Denton to see when I was going to receive my service, they didnt have a ticket for me. I told them Assurant said they would be providing my warranty service. McNiels told me they only service what they sell! I called Assurant back, they turned it over the scheduling gods. Three days later they set me up with a repairman 45 miles away. After waiting on him for four days he says he just doesnt have time to come by and pick up my refrigerator to take to his shop. I call Assurant again and am told its being turned over to the scheduling gods again. Three more days go by and they set me back up with In Home Appliance Repair. I call and they tell me they will be out on July 7 2014. The evening of July 6, 2014 In Home Appliance Repair calls and tells me theyve decided since the defrosting didnt fix the problem two weeks ago it was a system failure and they dont do that type of repair, they would call Assurant for a different service provider. I call Assurant to see whats up, they tell me A&E Factory will be out on July 13,2014. Now nearing a month WITHOUT a refrigerator and still not knowing how long its going to take to fix the problem! If Whirlpool is trusting Assurant to provide extended warranty service then thats exactly what they should be doing, it certainly isnt my fault they cant get service people out in a timely manner to resolve appliance issues. Its not like being without a stove or microwave - this is a refrigerator!!! This is the poorest service I have ever received from Whirlpool and Ive been a faithful Whirlpool customer for many years. In my opinion they should bring me a new fridge, haul this piece of crap to the nearest dump and be done with it! And after reading some of these posts there are lots of people that feel the same way about their appliances. This type of Customer Service needs to STOP, $2700.00 for a refrigerator and have to deal with crap like this is crazy!!!

My oven had been temperamental since day one, then got worse over time. I do not use my oven that much so was not really worried or alarmed until a tray of cookies caught fire. It was set at 350 and jumped to 525 on its own. (I bought an oven thermometer to monitor) Minor burn taking tray out but all okay :-). Contacted Lowe’s where we bought it and they would do nothing (note: at this point the oven is 15-months old and out of warranty). Advised me to contact Whirlpool. Did that - they sent out a repair service and they determined it was the temp. sensor. It is now April 2014 and I am still waiting for the part (this all started Sept 2013). I have since talked and wrote to Whirlpool for this to be resolved and also asked that the range be recalled due to fire hazard at the least! When I spoke to them in December, they said they could give me ‘50% off the part’. Remember I am still waiting for that part, lol! After writing corp h/q, they said “Sorry, since we cant get the part why not have someone come in and take the old part out and have it rebuilt.” I ask you Whirlpool w/q would you be happy with that??? Will post any follow-ups... would love to hear from anyone else with this problem - model # GFE461LVS. Great day everyone. :-)

I had my range installed in January of 2015. The very first week, using a new Farberware non-stick skillet, the cooking surface became permanently scratched. Could not polish it out, and polishing - it must be done every time you cook on it! In early September the cooling fan for the electrical panel went out. Also, the convection oven would not maintain heat. Had the cooling fan replaced last week. Its out again, along with the convection oven not maintaining a regulated temperature. Also, 3 months ago, my grandson put a ceramic casserole on the stove top. After he took it out of the oven, it permanently scratched the paint off the control panel. Im very disappointed in the fragility (painted plastic surrounds top of control panel) and unreliability of this product, a total lemon.

Love the chrome exterior and overall appearance of this side-by-side. The compartments and shelf spacing are well thought out & offer flexible adjustments. The outside components on the freezer (crushed ice, ice water, ice cubes, & light) I love, and most importantly the unit comes with a built-in replacement water filter.

Why am I not surprised by this stupid American company? I purchased a brand new fridge in June this year and for the last 5 months I have had about 20 different technician visits by five different technicians who changed almost everything you could possibly imagine - evaporator, control, sensor, compressor, display, etc., etc. And the company still refused to take any responsibilities. They kept telling me that more inspection was needed EVEN AFTER all the technicians said there was NOTHING THEY COULD DO. After having to yell at them for about an hour, they finally realized they had to issue me a new fridge. What a piece of crap they are. Even then when I called back about the exchange, they pretended they could not find my file. WTF??? They really tried EVERYTHING they could not to issue an exchange. Wow. What an incredible company and its customer service. I will never, ever buy another American product - nothing complicated with computerized parts anyway. They are NOT capable of producing such complex machines. They should stick with toasters or juicers - lol. Stupid Americans. LG and Samsung all the way baby!!! ** you Whirlpool.

I took the time to read the owners manual, and then ran machine (washer wtw5000dw0). Using an affordable HE approved detergent (Xtra), I had no problems. If the washer doesnt fill or drain correctly, look up how to recalibrate it, was easy to do because I did that after transporting it. My clothes are cleaner, and I am using LESS detergent!

I purchased a brand new Whirlpool Cabrio washer and dryer set not even 2 years prior. When I first started using it, I pulled shirts out of the wash after being ran through and found deodorant marks still on the inside of the shirts. I had to wash all of my loads on heavy soil and still had to run some loads through more than once. The wash machine quit working about 1 month ago, so I had a service man out to look at it. It ended up being the control panel and the part itself was going to cost me $300 and by the time I paid to have it repaired, the total cost was just under $400. The service man proceeded to tell me that Whirlpool had another company actually make the control panels for the Cabrio model and he has serviced several of these washers and when he would repair one part, another part would stop working. I was very upset and bought a new wash machine. I would like to add, I am a single mom with a 2 1/2 year old, so the wash machine was not used excessively in any way. I dont work outside so my clothes are never soiled heavily. Needless to say, my washer was not under warranty so Whirlpool couldnt do anything for me. A wash machine should last longer than less than 2 years. I would not recommend this model to anyone. And for Whirlpool to put their name on such a poor product is very disappointing since I have had good experiences with their products in the past.

I purchased the Whirlpool washer with the expectation of having at least clean clothes. In fairness, I do wash some pet items but they are done separately. My clothes at time come out dry in spots because theyve not been touched with water. Forget the balancing issue. What I will have to do is wash, rinse, and repeat. This will be my life until I can get a new washer. Never again Whirlpool.

I hate the thing. The grates are way too large, they are too heavy, and the fact the high is not a true high and the other three are different temperatures. The oven is awful. It half cooks. You cannot do decent canning on the thing because you only have one burner. This is a mess from the get go. Why in the hell do companies think everything has to have a computer attached to it? Computers and heat do NOT mix for Gods sake. A simple gas stove is sufficient to cook with. Take the computerized junk off and make a normal stove.