I have had my refrigerator for eight years. Only had one prior repair which cost me $85. I have had a wonderful experience with this particular product. I am pleased with the liability and hope to replace with an equal or better appliance.

I purchased this washer about 3 years ago to replace a dishwasher which lasted 20 years. Within a year the racks began to rot, the front panel plastic started to peel off. Within two years half of the racks rods completely rotted away. 3 years later the washer is busted - most likely pump which was probably blocked by one of the pieces of the rack rods. I am replacing it with Bosch - German engineering. Needless to say I will NEVER buy a Whirlpool - formerly reputable company again. Good-riddance Whirlpool.

We purchased a Cabrio top loading washer (WTW6400SW2) and a Cabrio dryer (WGD6200SW1) in 2007. From day one the washer has tied clothes in knots, never cleaned the clothes properly, and sputters the detergent and bleach unevenly. The fabric softener dispenser clogs up too, rendering it useless. The knotting of the clothes leaves them so tightly wrinkled they come out of the dryer very wrinkled. The water level, determined by the washers self-sensor that weighs each load, does not fully submerge the clothes. The manual says this is normal operation for this model and that it will not affect the cleaning process. Wrong. The small agitator is insufficient to clean the clothes but does a wonderful job of twisting them in long, tight knots. I want to kick myself every time I walk past the washer for paying so much money for such a poorly designed washer. I was very sick when they were first delivered and wasnt able to do much laundry. By the time I was well enough to do more with it, I noticed the clothes werent getting clean and were actually being damaged by the washers process thanks to uneven detergent distribution/spotting from the clothes sitting above the water level, and being poorly agitated and rinsed. Before I knew it, my warranty had expired. It was a very hectic year. Ive been very sick. We purchased it from Lowe’s. I had their techs out a time or two to check it in the beginning, but they always smoothed it over with some waffy, generic explanation. Eventually, I was past my 30-day trial period. I was on my own with Whirlpool, whod refer me to the manual and make me feel like I just had to get used to the new technology of the self-sensoring washer. Ive read that Whirlpool is aware of this issue and doing nothing. Ive read other complaints that describe the same problems I have and its obvious this is a design flaw. I appreciate these posts because I least I dont feel like Im insane anymore. No, just horribly ripped off by Whirlpool.

I purchased a gas range with JDR8895 last 09/06/2007 at Home Depot in Metro Denver for approximately $1700.00. I will make my final payment on my Home Depot account next month. I was preparing dinner last September 10, 2011. I had the pans on the cooktop, one on the right rear and one on the left front burners. This was the set up because the right front burner has stopped working some time ago. Both burners were on a low setting as I was simmering pasta sauce and just warming water as I was later going to boil it for the noodles. I was in my living room when I started to smell something odd. When I approached my kitchen, there was a fire coming from the rear of the cooktop and beneath the three burner knobs. It smelled like an electrical fire. I immediately turned off the burners with my hand wrapped in a towel and started putting out the fire by hitting it with the towel and blowing. The towel caught on fire. I grabbed my fire extinguisher and was ready to spray when finally, it looked like it burned out. The smell in my home is terrible, when I tried to test the lower burner it looked like it was catching on fire underneath the knob as well, so i immediately turned it off and batted it with a towel. Im not sure what happened here. I will make my final payment on this range next month and had the previous range in here since 1977 and that still worked fine. I spent a small fortune on this Jenn-Air, only to have it catch on fire that could have potentially burned my house down.On various web sites including consumer affairs, JDR8895 has many reports of fires. If this is a known problem, why has it not been addressed as a recall? My 9-year old was making soup the day before while I was in the living room. This could of easily happened to her! It is a very dangerous situation to put your consumers in!Whirlpool Corporation contacted the appliance repair company, Columbine Appliances, to inform them that they would only be covering the cost of their visit and not the cost of the parts to be replaced in the range (the ones that caught on fire). Through Columbine Appliance, Whirlpool wanted to inform me that this is not a safety hazard and that it was my fault as I got water in the control knobs. This is not true. If I did, I was not aware and was unable to find any literature about that being a safety hazard or that it could cause a fire. I have found and have forwarded to the CPSC many instances of this exact problem, often when the range was not even in use and are happening to other consumers. I am working on combining the data, contacting the other consumers and have since refused service on the range by Columbine Appliances. Whirlpool only tried to contact me after I left them a message regarding the status of the range and that I had no interest in paying for what I viewed as a defect in their range and a safety hazard. I found a news story of this range going up in flames. Its unbelievable that this company continues to stand behind this product and blame these fires on the consumers actions. I am disabled and have an oxygen machine in my home. I have no desire to have this unit catch on fire again and potentially die, especially since water does, on occasion, end up on cooktops. Thank you for your time and attention to this matter.

In a recent decision regarding the highly expensive, supposed elite performing Whirlpool Gold refrigerators, a group of unsatisfied Whirlpool owners who are tired of cleaning water puddles from in front of their new refrigerators have hired all automobile corporations to manufacture cars only available to the CEO, Executive Board as well as the entire engineering staff at Whirlpool.These cars will be guaranteed to run ok. However, once the car is heated up under normal working conditions, the cars will be guaranteed to leak oil all over whatever surface they are parked upon. We hope that this will not be an inconvenience to the CEO of Whirlpool; however, perhaps once you have destroyed your new garage floor, you will understand the nature of our complaint with your poorly designed and engineered Whirlpool product.While this letter will have no effect on my current defective product provided to me by Whirlpool, it makes me feel better and I have not had the attention span to listen to my wife complain while she is cleaning up yet another (whirl) pool underneath our fridge.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

Similar to what I am reading below and on other sites, my hot water heater stopped working. I spent about an hour trying to relight the pilot light, which apparently you cant do with this model because it breaks. My first thought and action was to call a plumber to come fix it. When he arrived he said it was reverse thread and that I would have to call Lowes to get a replacement part. When I called Lowes they said they would call Whirlpool and then give me a call back. Two days later I still havent heard back or taken a shower; I am going to the gym tonight. Finally, I got online and called the 800-number and am being sent a part to arrive tomorrow. I asked to be reimbursed for the cost of the plumber since they obviously knew they had a problem (they assumed why I was calling the warranty line) and redesigned the issue with a voluntary recall. Whirlpool, please make this right. I know you license your name to American but it is still your name and brand reputation.

My wife and I purchased a Whirlpool Duet washer and dryer 5 years 1 month ago. We purchased the front load style because they were supposed to be better made than the older style. Its just my wife and I no kids. We never overload the washer or dryer. Now the drum bearings in the washer have gone out. I feel that a washer should last longer than 5 years and 1 month. I dont think I will be buying another Whirlpool.

My son purchased a Whirlpool washer and dryer as a Christmas gift on 12-24-10 from Sears. It didnt wash the clothes properly and I would have to rewash them. Also, it would not spin the cloths properly and the top would take forever to unlock. Then in July, I called for repair because the water would not spin out at all. It took at least two weeks for them to come out. Another two weeks to get the part they ordered then to find out that they also needed another part that was not diagnosed in the first place. After another three weeks had gone by and having to go to the laundry to wash our clothes several times, it was finally fixed. I continued to have problems with the clothes not getting cleaned. How can this possibly be an energy efficient product when you have to do the load twice? I am so grateful to my son for the gift but am so dissatisfied with the product. I rate this product 1 out of 5 stars.

I am concerned that Whirlpool microwaves installed over the stove have extremely faulty doors. I have two homes in which I have Whirlpool microwaves, and both have huge cracks in the door and small pieces inside the doors beginning to fall out. It deeply concerns me that it will cost more to replace the doors than to replace the microwaves. I have always believed in Whirlpool appliances but now feel that I will have to change brands. My question is “What in the world is wrong with your doors that they crack so easily and the company holds no responsibility with such faulty work?” I would simply think that this was just a faulty door on my microwave, but I have two that are cracked! This definitely means you have a faulty product.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

Once again I am disappointed in a product that I felt was of the utmost quality. However after buying in 2010 and not being installed until 2011, the over the oven microwave has a crack on the outside of the door. Two pieces have fallen off from under the plastic rim on the inside of the door, two pieces of the door one on the top right side and the other on the bottom right side have fallen off. All I have to say is the two Whirlpool products I bought at Lowes has been a huge disappointment especially since the other two bought from the same stores are Frigidaires and work beautifully...

Whirlpool Quiet Partner II Model # DU1055XTUS1 - We bought the dishwasher in Aug 2010 and after the 2nd yr, it started to occasionally shut off by itself in early cycle. After 3 yrs, it now shuts off repeatedly... needs to be restarted at least 15 times. It use to shut down early in the cycle. Now it shuts off whenever. I should have read the reviews on this dishwasher before buying but it was on sale for such a good price. I guess I got what I paid for. Just keep in mind that Whirlpool dishwasher seem to last only 3 years. I guess thats also why their warranty for electrical parts is one of the worst compared to other brands.

We purchased our home brand new in June 2010 and with it came all Whirlpool appliances. We started having cosmetic problems with our over the counter microwave about 2 years later (model WMH2175XVS-2). The plastic casing around the door handle started to crack on the top and the bottom and now both pieces are completely gone as they fell off. The handle is still attached and the microwave is usable; however, it looks shoddy. To replace it, we were told by a Whirlpool authorized repair person that you would have to replace the whole door at a cost of $300 or more if you include labor. I am disappointed that this happened and that we cant get it repaired. It makes me think again about purchasing more Whirlpool appliances.

Bought a Whirlpool fridge (WRF560SFHZ) 3.5 years old not cheap! Suddenly one day, the freezer drawer cannot close properly. Since it broke down on a long weekend, I have to wait 3 days in order to contact Whirlpool customer services. And then wait for another 4 days for them to send a technician. The technician advised it is a screw on the rail fall down and he fixed it and charged as 115CAD repairing fee (for a loose screw). He said it is a product defect from Whirlpool and that we should call Whirlpool to ask for a refund.Of course after a long wait from the hotline, Whirlpool refused to refund, saying that, It is not within warranty period and it is perfectly normal that you paid for 17** CAD fridge and can only used for 3,5 years and that things happens (screw can get loose). The service rep. even said, You bought it, it is your property now... And they dont care you have to throw away food in the freezer since the door cannot be closed. And of course they refuse to admit that the product has an inherent defect... Will never buy this brand ever again!

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

Model # WFG510S0AS1 SER #R30850040. Oven was installed NEW in the home I purchased in July of 2013. I used the cleaning feature on it in Nov 2014. I am amazed that it did not start a fire. Please see pictures attached. The whole control panel melted. This makes the oven unusable and extremely dangerous. I will need to replace the whole control panel. I followed the instructions completely in the manual provided for the cleaning cycle. It says in the manual to only clean the over this way as using easy off or any other cleaner will damage the inner surfaces.Whirlpool claims they have no knowledge of this problem but there are numerous complaints on their site about it as well as other internet sites complaining about the melting of the control panel. I need to know how to fix this problem and dont believe I should have to pay for something that is obviously a flaw in the materials used. It is extremely dangerous. Since these pieces of Whirlpool equipment were installed by the broker that originally purchased the home, I have no record of purchase. I can try and contact him and see if he has anything but kind of doubt he has receipts now.

We bought the WDF330PAHB1 Whirlpool Dishwasher from Lowes last year. It is a terrible dishwasher. It does not wash or dry the plastic dishes well and has a continued foul spoiled milk smell despite many cleanings with dishwasher cleaning tablets. I use Cascade and Finish rinse aid. My china and glassware are fine and it is a quiet unit but this gook I have to keep cleaning up is gross. I clean the removable filter and screen 2-3x a week but the stuff gets on and in every place it can cling to. Its a greasy, smelly muck. Its in both water jets, so I have to constantly remove them and bang the stuff out. We pre-rinse our dishes (which Ive never had to do before) but still this slime keeps building up. Do not buy this machine. I wish I could give mine back!

I bought a Cabrio Washer and Dryer around January 2015 at Lowes. After going through the worse service imaginable, the washer was like pouring salt in the wound. I like the dryer fine, but months later, Im still unhappy with the washer. While it washes OK, it takes forever to wash a load. Most of the time, it does not spin the clothes out enough. There is no way to just spin again. You have to go through a rinse/spin cycle and you may or may not get lucky with a sufficient spinning. Why cant they just have a spin cycle and why does it have to take so long to wash a simple load of clothes? I have bought many Whirlpool appliances, but this is my last ever.

We purchased a new Whirlpool water heater April 2013 at Lowes and every 3-4 months the pilot would go out. My husband would simply re-light the heater, I guess he didnt think it was a big deal. However, in September 2014 the water heaters pilot went out and would not re-light, so I contacted Whirlpool about the warranty. It took 4 telephone calls (two of which involved a plumber, per Whirlpools request), and several days of cold showers for an authorization code to purchase a $8 part (thermo coupler). The hassles that Whirlpool put me through, no one should have to endure. Who ever heard of a technician telling you that they have to talk to the plumber, when you call them to explain a problem with your water heater, such as, the pilot will not stay lit and the plumber said it is the coupler (I couldnt remember the whole name of the part, but surely they should have understood what was wrong). Secondly, providing a plumber (unless youre married to one) to converse with them involves more money. Now I have a plumber at my house so I call Whirlpool and this technician insists that the plumber perform a test on thermo coupler to make sure that it was faulty before she gave the authorization for a new one. Yet again, when I called to Whirlpool with the plumber, while I was voicing my problems in resolving the issue of my water heater with this technician, and she just hung-up on me. So as not to be defeated and having already invested in the expense of the plumber, I called Whirlpool again and requested a manager. The technician asked if she could help and I informed her of my previous encounters. She apologized and took my information to have a manager to call me later; however, she did give me the authorization code for the thermo coupler without delay. When I went to purchase the part, I didnt have the old part (as trade; the plumber hadnt removed it), so I paid for it out-of pocket, to return the old part later.

My side-by-side refrigerator leaks water. I find water on the floor but we cant find the source. When I called Whirlpool, they stated its not under warranty, but we can schedule a repair appointment, I declined. Im still looking for the leak. Its intermittent, sometimes I dont see water for a while. The last fridge we had, we had to get rid of it because the sides and front got too hot to the touch. I was afraid it would cause a fire.

2007 we purchase a Whirlpool Casio washing machine. Rusted out in three years. 2008 we purchase Whirlpool gold dishwasher. In two years the front panel rusted out. We replaced this panel and now the second one has rusted out. According to Whirlpool they do not cover rust. When we replace the washer it was with a Samsung. NO SIGNS OR RUST IN THE LAST THREE YEARS. When we replace the dishwasher it will not be a Whirlpool. As far as I am concerned, Whirlpool products are junk.

I am on my second Cabrio. The first one only lasted a few years, but I stayed with the Cabrio line because I didnt want to replace the dryer. That was my first mistake. The second Cabrio washer constantly leaves a white residue on dark clothing. I used an HE detergent, reduced the detergent and put the dark clothes through an extra rinse and still find residue that has to be scraped off. I called Whirlpool on Dec. 19th, 2018 to complain about this and was told there was no history reported of this kind of problem. Then I went on the ConsumerAffairs website to learn that many others have the same residue issue, among many other products. I will not ever purchase a Whirlpool machine of any kind again.

I have hated this Cabrio washer and dryer set since the day they were delivered brand new by Best Buy a couple of years ago. The washer does not clean well, often does not spin dry, and leaves some clothes dry after a full wash cycle!!! I have to wash small loads on the deep water cycle to even have a chance at cleaning the clothes. The clothes are so dreadfully compacted and tangled that it takes great effort to birth them out of the washer, unfurl them, shake them, and put them into the next torture machine- the dryer. It is as if Whirlpool intended to build a machine to twist clothing so tight that it requires a bodybuilder to untangle the clothing. Then the items are so incredibly crumpled that ironing has found its way back into my already busy life. Ironing is a massive challenge to the degree of wrinkles in the clothing. The slanted tops are icing on the cake. Cant even pull the clothes out of the dryer to the top of it because they slide right off. Cool.

Love my Whirlpool stove and I just bought a Whirlpool French door fridge. I also have a Whirlpool washer and dryer and I am very happy with the way they work and look. I replaced my Tappan stove that I had for quite a while and it was a good stove but I am very happy with my Whirlpool stove, it not only works great but it looks great.

Bought a home with a Whirlpool WRF540CWBM01 french door refrigerator circa Oct 2016. The unit stopped freezing/cooling and the appliance guy replaced a relay and this did not help. I called Whirlpool to check on the warranty, only 1 year. Then, I called the extended warranty and they wanted $342 for 1 year and $567 for 3 year but wanted 60 days before this would go into effect. Hmm, wait 2 months w/out a working fridge, great idea. So, after 2 short years the compressor failed and nobody will attempt this job and cost is too high. Had to buy a new GE fridge w/ a 5-year parts/labor covering this type of issue. Whirlpool needs to fix these issues. Very disappointed.

I purchased my Whirlpool Double-Oven one year ago and couldnt wait to use my new oven. I was told it was so efficient because I could use the top oven for quick baking instead of heating the entire oven (plus I could set it at different temperature settings). About a month in, I cooked 2 pizzas side by side. The first one burnt to a crisp and the one right beside it was doughy on top and burnt on the bottom. Not thinking, I blamed the pizzas! I also blamed myself, thinking it was me not being used to the stove.A few weeks later, I baked cupcakes. About 15 minutes in, I smelled burning and the cupcakes were raw on top and burnt black on the bottom. I called Whirlpool and they sent a technician out and he replaced the circuit board/clock. Worked for a couple of weeks and then the burning began again. Called Whirlpool again - another technician came out and adjusted the temperature. Here I am again, had to call Whirlpool again.This stove has been so inconsistent and Im so tired of wasting food because of this stove. My 4-year old Whirlpool dryer also went out last week so needless to say, Im not very fond of Whirlpool right now! If you are planning on buying a Whirlpool product, buyer beware and I hope you have a lot of patience...

Whirlpool 29 cu ft French Door Refrigerator WRF989SDAM - We purchased this refrigerator September 2013 for our new home. We moved in November 18, 2013. The refrigerator made a very loud buzzing/humming noise from the beginning and did not make enough ice. The shop we bought it from came on 2 occasions to work on the ice maker and finally totally replaced it. Then the rack on the bottom of the left door fell out and contained glass jars of pickled vegetables. They broke and made a big mess and etched our travertine tile floor. We called the shop and they sent their son out who put the rack in with duct tape which of course did not work so we took it out and put it in the cabinet. We had to pay to have the tile polished to remove the etching. On the weekend of November 15, 2014 the humming noise was so loud that we called the repair person again and they came out on November 17, 2014. At first they thought it was a fan motor but the freezer started making a loud noise and the owner came and said the compressor was going out. Our food was beginning to thaw and we asked if they could at least loan us a refrigerator to use. They brought us an old small fridge which was put in the garage. We took all our food out there. They came November 25 and picked up the fridge to be repaired. We had been told the warranty was out but after calling your company they were told Whirlpool would cover parts and labor. Today is Thanksgiving Day and we can not cook a big meal due to the small fridge and freezer and we are buying bags of ice every day. We have family visiting and must go out for dinner. We have no idea of when our refrigerator will be returned to us. This has been an expensive and disappointing experience. I would never recommend your refrigerator to anyone due to this experience. I really feel we should have been offered a new refrigerator at a discount. We bought all our appliances from Dons Appliances in Okeechobee, FL 34974 and they are all Whirlpool. This refrigerator cost $2299 and our total order was $9,642.84. We would appreciate a response from your company.

I love my Whirlpool refrigerator, its great. I have not had any major issues with this brand. I only wish that the freezer was made a little different. Im not a big fan of the side-by-side doors. I would much rather have the one with the freezer at the bottom and the fridge at the top...

If you have the double oven below with bad board, start shopping for a new oven, but the part is no longer made. How can you end of the life a product after only 6 years? This is about the RBD305PDS12 double oven! I have wasted 3.5 days with Whirlpool/Maytag. Its very Frustrating how each department passes you along and makes promises about what the other department can do, resulting in zero satisfaction. None of them are well informed to say the least.I have a 6-year-old double oven that has a bad board and after 3 days, I find out it is no longer made. I paid $1500.00 six plus years ago and now I get to spend $2000 plus to get a new one. Again, how can you end of life a product after only 6 years?

I purchased this washer 3 years ago. At year 2, I had to replace the RPS part. The codes that appear represent 2 different issues as well: one being the RPS part and also for the control panel. In less than 1 year since this replacement, it is broken again! The clothes do not get very clean. You cant soak whites in hot water and bleach (it drains after 5 minutes if you stop it). You have to use the bulky setting to get enough water to actually wash your clothes. If you get too much detergent, your clothes comes out crunchy feeling even with the extra rinse.I thought this Whirlpool product would be great since my 22 year old dishwasher is a Whirlpool and still works but as the old saying goes... They dont make them to last like they used to. To say this washer is a POS Lemon is an understatement! I also have the companion dryer and it is starting to have problems including the door latch breaking into pieces. I will never purchase another Whirlpool product again! I have been told that Kenmore and Maytag are also under the Whirlpool umbrella so Im not sure what I will buy next. My recommendation: DO NOT BUY THESE PRODUCTS!!!

Whirlpool W8RXEGMWQ01 leaks - It looks like the seal is not tight around the freezer box. They blamed it on my floor but I think its because the door sags. The door needs to be lifted about 1/2 to fit snugly into the freezer box opening. They came out three times but couldnt fix it, then they said it was my fault. Then I finally gave up.

I bought a house 2 years ago that came equipped with all new Whirlpool kitchen appliances (refrigerator/freezer, stove top and dishwasher). A few months ago, the damper door in our refrigerator broke causing food in the refrigerator to freeze. Just the other day my Whirlpool dishwasher stopped draining properly. Both instances a repairman was needed and were now out over $400 for repairs and parts. I would definitely not recommend purchasing any Whirlpool appliances and I am deeply frustrated that Im having to deal with these repairs and costs for appliances less than 2 years old.

Very similar experience with warranty issues as everyone else. I purchased a brand new $2k side by side stainless steel model in Dec of 2013. It began not cooling in August of 2014 and they have since had 8 repairs and still will not exchange the fridge/replace the fridge. We finally had to buy another fridge and put it in our garage in order to have food in our home (of 5 kids and 2 adults). Ridiculous customer service every phone call. Possibly the least educated, rudest individuals always. Never buy from Whirlpool - worst reputation ever.

I have had this washer for about 7 years. I have not had any problems with it. I wish that it is stingy with rinse water. I see suds on the items before the rinse cycle and it doesnt seem to use enough water for a good rinse. Therefore I use the extra cycle.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

I just purchased a new Whirlpool 6th Sense hot water tank #333570. This unit is a piece of garbage. Whirlpool should be ashamed at the quality of product they make. This unit came with a bent temperature and pressure relief valve, which required a piece of copper tubing to be bent awkwardly just to remedy the situation. Also, the control box is set at 12 (most other brands are 14, which is common), forcing the gas lines to be re-piped (very expensive). This unit also is extremely noisy, runs really, really hot and is not energy-efficient at all. Shame on me for not researching this product more closely. If youre buying a new hot water tank, steer clear of Whirlpool products.

Cabrio fabric washer and dryer sucks. I gave almost $500 for a piece of **. Doesnt get the clothes clean. Hell most of them dont even get wet. Its junk. Wouldnt have another one. Lowes junk and the dryer aint know better. Its always flashing check lint even when its clean and you have to ** with it just to get it to start.

I bought a 38 gal. low boy electric Whirlpool water heater from Lowe’s. It was replaced because of a leak around the upper heating element after only one year. Now, the replacement heater is leaking in the same place, and it has been leaking so long that the electric terminals are rusted, water is standing in the cover plate, and the lining is soaked. I cannot see behind the plate and dont know it until the water finally made its way into the drip pan beneath the heater. When we saw the standing water, we turned off the electricity and shut off the water to it to stop a fire hazard. The warranty is up on my water heater, but my concern is that this could cause someones home to burn.

Whirlpool Dishwasher purchased at ABC Warehouse in Chesterfield, MI and was delivered on 10-2-2014, and one year later, we noticed that the tips of the lower basket were coming off. We contacted the holder of the extended warranty (5-yr.) and also Whirlpool. Both replied the fault was cosmetic and was not covered by warranty, that only mechanical/electrical components were covered. When we were buying the extended warranty, we were told that we were covered for all issues that may occur. We werent told cosmetic flaws were not covered. I guess consumers should, before buying a new product, make a specific list of possible problems, and make sure whats covered and not covered. We have been unable to resolve this issue.

I am a very unhappy owner of a Whirlpool Cabrio Model: wtw5640xw0 & matching Dryer. About 4 years ago, my husband chose to replace our 11 year-old Maytag Performa Washer & Dryer instead of fixing a part that needed to be replaced in the Washer. I was upset with the very first load of laundry in the Cabrio and I was extra upset that my husband had junked my perfectly awesome working Performa Dryer. )-: First of all, the Cabrio set is Extremely LOUD! Secondly, I often have to wash loads more than once because they do not get clean the first time. Next, the Washer is Always knocked off balance. Ive resorted to using the settings on the Washer with the low spin every time, no matter how light the load. And, now there is something wrong with the lid lock mechanism (which has always sucked anyway), but this is a new problem... I was just checking on the internet to try to figure it out when I stopped to write this review. The lid will not lock & the lid lock light wont go off, so the Washer wont do anything at all! I can not express enough what a piece of junk this Washer is & Im never going to allow my husband (who doesnt even do the laundry) to choose my Washer & Dryer again!

I am the owner of a 4-year-old stainless steel Whirlpool refrigerator, Model GB9SHDXPS02. Yesterday morning, my 5-year-old daughter opened the fridge door to get a snack. The door came crashing down, hit the floor - missing my 21-month-old daughter by less than two feet - the drawer smashed off on impact and flew across the kitchen floor and the contents of the drawer (salad dressings, syrup, condiments, etc) went flying too. Miraculously, no one was hurt. My children were obviously upset and crying, and I was shaken. My laminate floor has a large dent and long scratch from the impact.My fridge door is broken. I cannot get through to Whirlpool Canadas corporate office to speak to anyone. The Whirlpool Canada call center is giving me the runaround. Yesterday I spoke to a supervisor at the call center who advised me that someone from the Corporate Safety Division would phone me within 24 hours - but I have not received a phone call and it has been more than 24 hours. I am noticing a complete disconnect between the gravity of the situation and an appropriate response from Whirlpool. I am a mother of 4 small children - two of which were very nearly killed/badly injured by a faulty refrigerator door. I cant even get a phone call in response. This is a serious safety issue. Im tired of apologies, some real action needs to be taken to ensure this never happens again to any consumer.

I purchased a Whirlpool Water Heater BFG1J5040T3NOV from Lowe’s and have had numerous problems. The biggest issue is having to replace the thermocouple three times. It works fine for about a year then I need to replace it again. This is tiresome and wasteful and Whirlpool should be ashamed. As a company that once had a high reputation, this is sad. I would not recommend buying anything from them, especially their water heaters. After repairing this one, again, I will look elsewhere for the next one.

Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.

We purchased this Whirlpool refrigerator at the end of July 2018. At the beginning of November 2019 all the interior lights went out at the same time. We called the store where it was purchased, and they instructed us to call Whirlpool. Because a year had passed, they were not willing to do anything other than put us in touch with someone who could service the refrigerator. We already know the repair will cost over $200. That does not include payment for the service call or the labor. At almost the same time we purchased a new Whirlpool microwave. We have also had problems with that. My advice is to stay away from Whirlpool products if you want something that will last longer than a year.

I wrote you about this oven. This morning, they replaced the thermostat and then wanted me to self-clean it again. Now it wont work again, so I called Whirlpool and wanted to replace it and it would cost me $1,070 extra. I told them that was not acceptable. I paid over $3,000 for the one I have. Now, I have to stay home again tomorrow so they can replace the same part again. To keep in warranty, I have to replace the part every ninety days if I want to self-clean my oven.

I bought a Whirlpool water heater from Lowes. I had trouble with it from day 1. It never worked correctly. Their service department is terrible. All they want to do is sell you extended coverage policies on it. Every time I have it fixed, its never covered, and I have to pay again. You will be sorry if you buy a Whirlpool water heater.

I love my Whirlpool LP Gas Range. Cooks great and bakes wonderful stuff. Also has a drawer under to hold pots and pans. Self Cleaning Oven. I do a lot of baking and I cook three meals a day. The burners are easy to clean off on top. I try and wipe spills up in the oven as much as possible, It has everything on it that I love, except it could have a plug in which would really nice.

Multiple issues with the Gold Series. Have lost two refrigerators full of food!!! First problem was ice on the back wall of the fridge. 2 years later refrigerator is not blowing cold air and it is only 4 years old!!! Terrible product!!

I purchased this fridge in February 2015. In August, the handle on the fridge door broke. I called for a replacement on 8/7, on 9/14/15 I received it. It broke on 10/3/15 and had a replacement on 10/13/15. It broke again on 12/26/15. I called for a replacement. I should get it in 10 days. Obviously, there is a flaw in their design. What bothers me is that no one seems to care. I will hope I never have to buy a Whirlpool product again. And I will certainly discourage anyone I know who is thinking about buying their products. I purchased this product at Lowes and they did not care when I went to them.

I sold my 4 yr old Maytag and bought the Cabrio 3 yrs ago because of all the manufacturer promising advertising. Its a top load with agitator, but it takes 2 hrs to wash a load and buzzes the entire time. So relaxing coming home and spending my evening listening to this buzz, so loud I have to max out my tv to hear it. With 2 hrs spent washing a load, I can only do one per evening. Whirlpool you owe all of us a replacement or a major discount coupon toward another (50%) if you are worth anything at all. You are scum!

I purchased washer (Whirlpool Cabrio wtw5600xwg) on April Fools Day 2011. The first repair was check on 1-27-12. I complained the machine was too loud and clothes seemed too wet - the call was under warranty but tech was unable to verify complaint. So guess what? On Jan. 21, 2013, machine sounds like a stressed jet engine. Now we are diagnosed with a bad gear case for a total repair of $439. Now we are not under warranty and Whirlpool takes no responsibility. Doesnt the consumer have any rights? Do you think Ill buy Whirlpool again?

We purchased a front loader Duet in August of 2011. It is now January 2013 and we had to have a service person come out. We did not buy the extended warranty because a washer should last longer than 1 year 5 months, but not ours! We need to have the drum replaced at $600. Are you kidding me! I will never buy another Whirlpool product.

Cabrio washer - I have always had a Whirlpool appliances and have always been satisfied with them, but this is the worst washer ever manufactured. I bought it to wash heavy loads of jeans and it takes me all day to wash 1 load because it is always out of balance. No matter what setting I put it on I have to keep rearranging the load. Without putting up with that, the load takes 87 minutes on bulky wash. That is far too long and then you add all the time I spend rearranging it to get it to work. I think there should be a recall or at least admit you have a poor design. My son works for Whirlpool, but Im not sure I will be supporting this company again.

New range and the faceplate keeps melting. Had it fixed once and it is melting again. I have been trying to contact Whirlpool but to no avail. What is my next step and is anyone else having a problem with this.

This Cabrio washing machine is really frustrating....... It goes off balance all the time. It does not matter if you have a full load or partial load, I know it has a tendency to go off balance, so I try to put the clothes in evenly. BUT it doesnt matter, it goes off balance. When the washer is downstairs, it gets to be a pain. The lid lock is a pain also. If you forget to put something in the machine, you hit pause button then you have to wait forever until it unlocks, and wait forever to unlock when it goes off balance. When it doesnt go off balance, it washes everything just fine. But if I knew what I know now about it, I would have never bought it....... I would recommend a different washer and check the reviews, which I didnt do. :(

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

We have had the same problem with the magnetron in our Whirlpool Microwave Hood Combination. Replaced this part in Dec. 2012 after warranty expired. Cost of repair was nearly cost of microwave. Magnetron went out a second time this week. When I called Whirlpool customer service, the management rep was very hard line about the warranty on the unit and parts. Very clear this company has a product reliability issue and does not want to keep its customers. I dont plan to purchase another Whirlpool product ever. What a frustrating disappointment!

Hello. We bought this refrigerator from Costco, so we can have extended one year warranty for the appliance. When we need this then we are not getting help. Our Fridge is not working from last couple of weeks. Technician came a day late to see the fridge, then order the part on the 01/03/2017, I didnt hear back from service provider till 01/11/2017. Finally I got a callback after spend an hour on the phone saying that it will take one more week. I had to call Whirlpool to expedite service and because of weekend I have to wait another 4 days to get the part.There are 7 people living in my house including 2 yr old. We are having hard time with the food and waste of food. We probably throw away $200 worth of food. And spending money every single day on food. I have to buy every other day for my 2 yr old. Whenever I tried to call for compensation, I get transferred to different department. I am so tired with this kind of service. I would never buy any appliance from Costco or Never refer to anyone. Very very bad service.

Moved into a house with a 2009 Gold Series Dishwasher model GU2475XTVY0. It has never worked since we moved in 3 years ago, always left dishes musty and poorly cleaned. We basically used it as a rinse/dry and pre-washed everything by hand. Even then it would mold up frequently and required manual cleaning. Total piece of junk, but looked really nice, stainless finish. Yeah.Latest chapter is it completely stopped working. Called a tech out for the usual $80+. His advice: this is a total lemon, and has been from the start. Not worth repairing. So Whirlpool, is this the standard you have now? 5-6 years for a dishwasher life cycle? Noted that my fridge is a matching 2009 Gold series, it has also had several problems with keeping a steady temp and has gone through 2 control boards at a hefty fee each. I guess Im done with Whirlpool, running out of appliance brands to blacklist here...

I purchased a (second) Whirlpool washer (WFW87HEDW0) in October 2014. Since purchasing (and to this day), I manually dried the rubber gasket after completing my daily washes, knowing that mold growth was possible. I wash one to two loads of clothes about three to four days per week. During the first year, I did not notice any mold in this area and was confident that the manual drying and cleaning with Affresh was preventing mold growth. However, at the beginning of this year I discovered a little mold growth, which has slowly been increasing, in the inside lower lip of the rubber gasket. The image attached reflects mold in its current state. I was very surprise to see this happening since my diligent cleaning has been thorough and never ending. I even remove the soap dispenser tray to clean and air dry it outside of the washer and leave the washer door open at the end of the daily washes for extra fresh air circulation. This is my first official complaint about a Whirlpool front loader washer, even though I previously owned another (GHW9200LQ0) before this one and had mold growing on the rubber door gasket but, unfortunately, never officially complained about that old machine. Now, I dont qualify for the $500 compensation because I never officially complained three times within the first five years of owning the old washer. To my dismay, I did not immediately realize I had mold growth in the old washer. It was only until years later that a repairman told me that I had mold growth in it. In addition to telling me the price of replacing the rubber part and replacing a broken water pump plus labor would cost as much as buying a new washer. Before purchasing a new washer, I researched and read many reviews about Whirlpool and other brands before deciding on this new Whirlpool. I decided to give Whirlpool another chance and to follow their recommendations on the proper cleaning of the machine. Once again, I am disappointed and angry with Whirlpool and, now, have to figure out what to do with my current situation.

The board manufacturer number W10312659 went out. They replaced the board. The oven was 6 months old, luckily was still under warranty. We didnt purchase a extended one because mostly it had a good name and brand. Well after a year and a half the board went out again. It gives error code H5P which there is no error H5P. So the boards out. It is very costly and thats with you doing your own service. Never will I buy another Whirlpool stove.

We have had our catalytic oven explode into millions of hot pieces again for the 3rd time. Contacting them they sold me an extended warranty which Im trying to cancel and have been trying since 30th Mar to contact on ALL of their lines. It is permanently on hold or engaged. This company should be avoided at all costs. If you work for this disgusting company DONT!! You will be out of work soon! It is unbelievable how bad they are at responding to their (now ex) customers. What the hell are we in the EU for when a supposed UK co is Italian and they never respond (AKA 1940). Ludicrous! Incompetent! Stupid! Totally without comprehension. Do NOT buy ANY INDESIT or HOTPOINT products EVER!!! They are dangerous and you will NOT get any help to put them right.

I bought a Whirlpool duet washer and dryer. These appliances are still under one-year warrantee. My washing machine was broken for four weeks, and they have been unable to receive all of the parts needed to repair it. They have made three appointments to fix the machine, telling me that they have the parts and only to cancel the appointment the night before. I have tried to get Pacific Sales to exchange the broken machine, but they will not do that or compensate in any way. This is a top of the line model; I would have been better off with a low-priced model, and I might actually have a machine that worked. Whirlpool supposedly had the parts on back order, which is not what Whirlpool informed me when I was able to reach them.

My mother bought these two years ago along with a washing machine and fridge. And now they are falling apart. The dishwasher wouldnt clean the dishes so my mother called the warranty people. It took a week to have someone come out and say it was fixed. The very first load it wouldnt clean the dishes. Now it takes another week to have someone to come out and say they need to order a part. Once the part gets here two weeks later it took 6 hours to fix. They replace the whole bottom half of the dishwasher, could have easily replaced the whole unit. Now a week later the clothes dryer doesnt turn on.

After 48 years of marriage, I had never had a new, matching washer/dryer set. I had had several new washers, but only used dryers. These all were very good units and served me well for years. So I was excited to buy a new, matching set. I have never been soooo dissatisfied with anything in my life. As I have read from other reviews, the washer uses very little water, sometimes hardly enough to get the load of clothes wet, very little soap, and in my opinion, does hardly any agitating. I dont feel my clothes have ever appeared clean. The only ones that look clean were the ones that started out looking clean when I put them in. I know this is all an ecology thing, water saving, government guidelines, etc., but please give me my old washer back. It did enough agitation to get clothes clean. And the dryer usually will not get the jeans dry on the first attempt. I have tried various settings, and they just dont get dry. In short, I HATE THIS WASHER/DRYER SET. I have heard others talk about the same thing. No one likes them, but we are stuck with them. Would like to have the government step in and see how dissatisfied everyone is with them and force Whirlpool to give us our money back, trash these units, and buy something that actually works. PLEASE, IF YOU ARE LOOKING FOR WASHERS AND DRYERS, DONT BUY THESE. I believe they are called Cabrio.

I have a lower end 4 burner model but I love it. Both power burns are in the front (I would change that) and electronic ignition. The oven temp is true and heats up quickly, I bake upwards of 700 cookies at Christmas time. Even being a lower end model it works great and I use it everyday. I think it is more energy efficient than the model that I replaced, which I replaced in order to have the electronic ignition. I would recommend this Whirlpool Range!

This machine is 18 months old. First it failed to drain (LD code). Ran diagnostics and found the drain pump ($60) failed. The Mexican part was replaced with an Italian part. Two weeks later, the infamous F1 code flashed - control board. I sourced a new one. I ran one load and another F1 code is flashing. These are $150 electronic parts. Fuhgetaboutit. Im sending this ** to the dump and going back to electromechanical controls. I had a Maytag that lasted 15 years.

French Door Model WRF989SDAWOO: Horrible quality, worse support! We have a new French Door (not inexpensive). Within 3 months of owning it, we phoned in because the unit was periodically making a very loud, metallic humming sound. We were politely told that noise was normal, and that if the unit was working when the service man came out, we would be charged. A few months later, the noise was constant, and we noticed that the temperature was not stable. Freezer was set to 0, Fridge to 36, yet the thermometer was reading 20 (freezer) and 38 (fridge). We called in, concerned that it was failing. We were put on a schedule for 9 days later. We were told we would get a call the day before with a 2-hour window when the tech would come. That didnt happen. We got a call that the tech would come between 8:00 am and 5:00 pm (he showed up at 5:35 pm).We phoned in 3 days later to tell them that we were losing food (freezer was now showing 29, fridge 40). We were told (by both Westinghouse and by A&E Factory Service, which is Sears) that we should rent another refrigerator. When the service tech showed up, the first point of contention was that we had Whirlpools warranty (and had paid for the extended warranty) rather than Sears Master Protection agreement. Nevertheless, the tech finds that there is a problem with the evaporator coil, which had to be ordered from the factory. The tech was nice, and told us not to wait to be rescheduled, but to call him directly, and he would come the business workday after we notified him that the part arrived. Another week without a refrigerator / freezer, and now we have to worry about what the tech told us; these units are NOT of good quality, and have had repeated failures in the cooling systems.

I purchased the Whirlpool Cabrio (wtw6600sw2) about five years ago. Last year, the motherboard had to be replaced. This year, it started to have load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $75 to have someone look at it, and to fix it will cost almost $400, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. I called Whirlpool and my model does not have a recall, but models with same problems have been recalled. I will never buy a Whirlpool again!!!

Purchased a Jenn-Air single wall oven model JJW2427WS after seeing it displayed in an appliance store. Oven was installed as directed. Upon viewing the panel, I discovered that it does not light up. You cannot read the function or numbers, never mind start and cancel without a flashlight. I have been a Jenn-Air customer for over 20 years. This is the first time I have been disappointed. Also, has this model been discontinued or recalled?I wrote to the CEO of Whirlpool and explained my problem. I was told that this is not a functional problem, but perhaps a design dissatisfaction. I cannot believe that there are other consumers who are not having difficulty using their appliance without additional lighting in their kitchens.

I was so excited when my husband bought me this as a gift this past year as we are a family of 6 which means lots of laundry. The first few months I assumed it was operator error trying to learn how the new one worked. Well here we are months later googling why it makes my clothes dirtier coming out than they were going. It leaves black linty looking streaks on all my white clothes, both inside and out and leaves white linty looking streaks on my darks, also both inside and outside. It DOES NOT REMOVE PET HAIR AT ALL! If you purchase one, and have long haired pets that shed, expect to invest in some lint remover. Im on my third type in an attempt to save me time. I will say OxiClean laundry detergent seems to be the only detergent that actually cleaned the clothes. Sadly, stores around here stopped selling.And whatever you do, DO NOT USE LAUNDRY PODS. It DOES NOT DISSOLVE THE HOUSING AND LEAVES SLIMY RESIDUE ALL OVER YOUR CLOTHES. I believe this is due to the fact that despite the setting, it uses little no hot water. Which would be great if it actually cleaned your clothes. I could run my clothes under a faucet with no soap and they would cleaner than this pos. Bottom line. Dont waste your money and if you do keep your expectations very low!

We bought this Whirlpool washer dryer set last year and extended warranty. 7 weeks ago the washer stopped working. I have spent around 60 hours so far trying to get the washer fixed. Have talked to the repair shop as well customer care up and down the chain. 5 visits so far by technicians and still not fixed. Customer care people promise to call back w/update but never do. We were going to buy LG but bought this to give business to an American company. Now our patriotism is bearing fruit. Customer care blames AIG (service contractor) and Whirlpool say that they can’t manage AIG. At the end of our rope with constant trips to laundromats. Have no idea if it will ever be fixed. So frustrating to see the name of Whirlpool tarnished to this extent. Nobody seems to be in charge and everybody passes the buck. Whirlpool is a shameful example of a company that deserves to go out of business.

It is a good refrigerator for the price, but it is not big enough for our family. It does get very cold in the refrigerator part unlike our last refrigerator. I only wish it had more shelf space on the door and the egg place fit more than 6 eggs.

Whirlpool model WRV986FDEM Purchased May 31, 2017 from Lowes. Cost: 2,638.10 including 229.97 for the 5 year extended warranty. We’ve experienced four failures in the nearly four years we’ve owned this lemon. The first failure occurred within the one year manufacturer’s warranty period. The three failures since then have been fairly close together. Control boards and mechanical parts have been replaced. We are now waiting for a “made to order” part, with no scheduled delivery date. When I pressed Lowe’s on the reliability of this fridge, I was told that if four failures occur during the extended warranty period, they would give us a replacement. Considering the delays in repairs and frequency of failures, this is unacceptable. Do Lowes and Whirlpool expect their customers to just suck it up and do without a refrigerator for months while we wait? The warranty is worthless without prompt problem resolution. Whatever happened to real customer service?

I bought a new Whirlpool gas range a few years ago. I am now trying to purchase my 3rd control panel at a cost of $281.00. The oven will not bake or broil. The oven now a provides storage area until we can purchase a new range, which will not be a Whirlpool or any brand associated with Whirlpool. Very Dissatisfied.

In less than 4 years my dryer had to be fixed twice as well as my washer. The dryer does its job. The washer is one of those HE washers that does not use much water. Clothes do not get clean without much water so I always need to set the washer on bulky to have water to cover the clothes. I wished I had kept my old washer. It worked a lot better.

Its now Nov 8 and Ive been officially dealing with this issue since Sept 26. This washer was installed in a new home. After less than 10 loads, my washer stopped draining and I was left with a load of towel soup for over a week while waiting for a service call. I still have the same defective non functioning washer sitting in my home and have been unable to do laundry at home in all that time. So far Ive spoken with 2 customer service representatives. The first was incapable of scheduling a service call. She clearly did not understand how to operate the database used for scheduling. I was finally able to schedule appointment on my own but had to wait a week before the technician was able to come by. It was determined that either the latch mechanism or the mother board or both are defective from the factory.The second was just plain dismissive and completely unhelpful. I sat on hold for about an hour each time before getting to speak to a person. Ive also received two canned emails in response to my poor review of this washer on the Whirlpool website. They basically blame COVID for the delays and state the parts delivery should take 3-4 weeks. I was originally told 14 working days for delivery of the parts. We are already past both deadline with no end in sight. At this point, Id like the defective washer replaced rather than repaired. And for the record, this was a new washer (less that one month old) installed in a new house that now stinks to high heaven because slimy, scummy water that will not drain out has been there since September 26. Id really just like for someone at Whirlpool to honestly care about this and take a moment to address this issue.

Same problem a lot of people have written about in your forum. Purchased a double door stainless steel refrigerator, bottom freezer, # GX2SHBXVY from Sears Canada on 12/17/2011. Warranty expired December 2012. Now we have ice forming on the floor under the bottom freezer though water hasnt seeped out as we are now cleaning it daily. Sears wants to charge $75 per hour + parts as there is no extended warranty. Whirlpool says its a common problem with most other Competitor models too. REALLY, ITS NOT. Have checked with a lot of friends of mine with similar models. Nobody is having a problem with especially units hardly one and a half years old. My bro-in-law also bought a Whirlpool a year prior to mine. He is having no problems. See no reason to spend $300-$400 on a comparatively new unit. Also have a 7-month-old stainless steel Whirlpool dishwasher and 4-year-old Gold Accura cooking range. Now spend morning and nights looking at them wondering when they are gonna blow. Need to replace my washer/dryer too but guess which brand I am not opting for.

Whirlpool N50T91-403 purchased in Mar 12 had an error code 4. I knew the water heater had a safety installed in it when I was working on the plumbing and allowed it to drain the hot water side down to 16% of capacitance of 50 GL. After the plumbing issue was resolved, I saw the water heater had shut off (thermal protection) but the switch wasnt tripped as far as I could tell. Knowing small processors can only remember anything if they have power, I removed the Honeywell circuit board and with my multimeter probed all of the capacitors contacting them both (-) and (+) and in reverse order. Doing this forces the IC to forget its codes because they require a small amount of voltage to remember them, usually powered by a small capacitor. I reinstalled it and voila! Presto! It works again.

I purchased a Whirlpool Cabrio washer in 2007 and had to replace the control panel for $300 each time twice.

I redid my kitchen two years ago. Put in Whirlpool appliances because they matched my refrigerator. I have been very happy with all aspects. It looks good, it’s easy to clean and cooks well. It doesn’t have a lot of special settings. Less to go wrong.

Needed a washer right away and have had Whirlpool before. Simple & easy to use. Not confusing to the average person or teenager for that matter. Reliability from Whirlpool is excellent. I have had many products from them and have enjoyed them all. They have been quite reliable over the last 9 years. They are out of date but they work. Not a lot of bells and whistles but still nice. They are both full size and have enough options for me. I am still happy with the pair and would purchase again if needed in the future. Price was good at the time as I cannot see spending $1K on them. Not always the more expensive is a good idea either.

My very expensive Whirlpool refrigerator thats three and a half years old broke down before Thanksgiving 2020. I am not able to get parts until after May 18th 2021. After calling numerous times and spending lots of time on hold I was told February 11th by Whirlpool that they had the parts in stock and they gave me a price for each part. Then they connected me to the parts department where they told me they dont have two of the 4 parts that I need. The price that they gave me for the same parts with a lot higher than what they told me at whirlpool. Whirlpool customer service was terrible its as if they dont give a damn. They just dont care.I cant believe its going to be 7 to 8 months to get parts for a three and a half year old refrigerator. I have fallen down my basement steps where I have a small very very old refrigerator twice carrying food up and down. Spreading mustard and sour cream all over my carpet my stairs my walls. Not to mention the fact that I have bruises all over my body. If I were you I would not buy a whirlpool. Its going to cost over $600 for the parts replacements that is if I can ever get them. Im going to have to break down and buy another refrigerator. Remember Whirlpool customer service is terrible and you can just forget about getting the parts.

Most dissatisfying experience with Whirlpool. In 2013 I bought a stackable Whirlpool washer and dryer. Everything worked well for two months, and then the washer started having problems. The washer memory board unit (MBU) needed to be replaced. This was done under warranty. One and half years later I started getting the error F07 which means an electrical problem. I called Whirlpool and they told me a technician would cost $85 for a service call. I delayed the call until today.The technician came, did a diagnostic and then advised me that I would need a new MBU. The cost plus labour amounts to almost the cost of a brand new washer. To add insult to injury, Whirlpool advised the service call would cost $89. (They upped the price since my last call.) You can imagine my shock when the technician told me that the $89 covers the first 15 minutes. I paid $133.34 for one half hour diagnostic testing and to be told I need a new MBU which is on back order for at least 6 months!!! My recommendation is - NEVER BUY any Whirlpool product ever.

I have made a conscious choice to remove baked food from my diet back in early 2013. That has not stopped my wife from pursuing her passion for baking from time to time. It goes without saying that baking requires a well functioning baking oven. The one that came with our home was a Whirlpool Wall Oven/Microwave combination. Sometime in early 2014 the Oven broke down. I had no choice but to replace the combination. After doing some online research and a couple of trips to stores like Sears, Home Depot and Lowes, we decided to drop $2700 of our hard earned dollars on a brand new Whirlpool WOC95EC0AS wall oven microwave combo to replace the old one. Lowes sent someone home to take measurement to make sure that we ordered the right size for the slot in our kitchen. 2 weeks after the purchase, around March 27th or 28th, we had the Microwave/oven combo installed in our kitchen by some Lowes provided installation contractor. After installing the appliance, the technician demoed both the microwave and the oven part of the combo. Everything looked good and we were happy to see the shiny new appliance adorning our kitchen. Little did we know then that this would start a seemingly unending horror story. For the first 3-4 weeks we used only the microwave and it worked as expected. Then one weekend, my wife decided to do some baking. The dough was prepared meticulously and then came the first surprise, the oven refused to turn on. Feature not available - the message scrolled across the LED display. And horror of horrors, the microwave started giving the same message immediately after. We looked online for solutions, and we found one that suggested that we try breaking the circuit for 1 minute and turn on again we tried it to no avail. And now we went from having a working microwave/broken oven to no microwave/no oven.We waited till the next day or so before placing a call to the customer service number provided in our warranty receipt. By now the 30 day return guarantee had expired and it was the end of April, 2014. Product was now under manufacturers warranty. Whirlpool/Lowes customer service scheduled a technician to come take a look at the oven.My wife took a day off from work and waited for the technician. The technician from J&H appliance repair of SJ came home, took a look and then tried breaking the circuit and turning it on again after a minute; of course, it did not work. After consulting with someone on the phone, he decided to order some parts the main circuit board. He promised to come back after the part arrived. We did receive a call from J&H to schedule an appointment to install the part and schedule a time we did. J&H decided to no-show us on the appointment and my wife wasted another day of her time-off from work.We called customer-service again and this time they decided to send in a technician from a Sears owned company called A&E Factory Service. A technician came home and he went through the same steps as the earlier technician from J&H. This time, it was my turn to stay home and welcome the visitor. Finally when there was no trick up his sleeves to left to try, he decided he is going to order the main board. A&E technician did something different, he ordered the part to my home. I called him as soon as it arrived. We scheduled a time and he arrived to install the part. I stayed home again. Well, result was no different and the appliance was in no mood to oblige to our coaxing and cajoling. Feature not available, it continued to bleep out. He ordered 2 more boards to my home. I stayed home again to welcome the technician and he arrived again to install the 2 new boards but the result was no different than the last time. Feature not available - the zombie appliance screamed. He told me that there is only one that remains to be done which is to replace the front panel circuitry so he ordered it. By now it was end of June. We hadnt used the oven for 3 full months and the microwave for 2 months.First week of July, a new technician from A&E showed up early in the morning to install the newly ordered front panel. Surprise, Surprise - Feature not available screamed the shiny lemon sitting in my kitchen wall. The technician asked me if I will be home the whole day and I said yes. Another technician, a supposedly senior expert came by that afternoon. He tinkered with it for a couple of hours and like all who came before him, he surrendered. He said there is nothing left to do with the oven and that he is going to recommend that the oven be replaced.He left me a voice mail next morning saying that I need to call Whirlpool myself and apprise them of my experience and ask for a replacement. So I called the customer service after a long 1 hour talk with customer service rep, followed by a conversation with his rude supervisor. I was told that Whirlpool no longer deals with A&E that they broke their relationship with them as of June 31st, 2014. I failed to understand why that was my fault. I was told they need to send technician from another company, can you guess the company whirlpool recommended? It would be funny, if it wasnt incredibly painful to deal with horrible customer support representatives yes, it was the the no-show company J&H. I told him Id have nothing to do with J&H. So they recommended their only other option, a company called AGO.AGO technicians started showing up at my house since early July and I waited with baited breath for them to suggest a way forward to a resolution. Well good thing that I didnt hold my breath for that to happen. AGO technicians have made 8-9 visits to my home during July and August with the last visit being on Aug 20th. They replaced all the boards that A&E guys had already replaced the previous month. On August 21st, I received a call from AGO rep saying that they have given up that the product is irreparable. They gave me a reference number and asked me to call Whirlpool for a final resolution.I called Whirlpool customer service on August 22, 2014 and Spoke to Jennifer and her supervisor for 32 minutes. They wanted to restart the whole process of sending technicians to my home. It would be funny if they hadnt stolen $2700 of my hard earned money + all the lost hours and productivity + vacation time lost + headache they caused + the pain of not having a working Oven/Microwave in our kitchen + dealing with rude customer service reps, I lost it. I threatened to put the whole recorded conversation on YouTube. The rude inconsiderate supervisor hung up on me.I called back after a few minutes and spoke with a tad bit more reasonable rep named Ashley. At least, she had the patience to hear me out without barking at me about what my rights are as a customer. Well she had no better solution than to suggest another technician appointment what was the excuse this time? That the last technician from AGO didnt call Whirlpools tech support line while he was at my house. As if that is my fault. I agreed and we setup an appointment for Wednesday, August 27, 2014 between 8AM and 12PM with the same old company J&H who no showed me once. Goes to show you who Whirlpools associates in business are. They had only two companies providing repair services in San Jose AGO and J&H.I took the morning off from work on Aug 27, 2014 and waited till 12 noon and there was no sign of technician. So I called Whirlpool customer service number one more time. As you would expect by now, a rude customer service person named Eva from Michigan picked up my call. It was reasonably clear to me during that conversation that the J&H technician no-showed because appointment was not communicated to them. She emphatically claimed that my warranty is not a product replacement warranty but a repair warranty and that she needs to send me a technician to take a look at the product. Can anyone believe it? She told me I have only one option either to accept the perpetual technician visits or she will note that I have rejected their offer to service the product. I told her I am not rejecting anything, just exploring all my options. She assured me I had no other options. The arrogance of these people! So here I am, several thousand of my hard earned money stolen by Whirlpool and I still have no working product. Adding insult to injury, 2 weeks ago I received a letter from Whirlpool pitching me to extend my 3 year extended warranty to 5 years. They want to inflict more pain and charge you for the privilege.I have more options than Eva would want me to know. Luckily I have legal coverage under my benefit plans at work. Even more importantly there is social media and internet. I am pursuing those options at the moment. Heres the summary: Lowes takes my $2700 on March 13th. I get the Wall Oven delivered and installed on March 27th. A total of at least 15 repair visits are made to my home between first week of March May and August 21 (I have started losing count). Time since product purchase: > 5 months. # of times the oven has worked : 0. Hours spent talking to rude customer service reps: 4-6 hours. Time spent at home baby sitting repair technicians : > 100 hours. Lowes, Inc washed their hand stating 30 day money back guarantee is over. Its customer service people were not of any help either. UPDATE 9/15/14:Within a few hours of publishing this post (on 9/2/14), I was contacted by both Lowes and Whirlpool via Twitter. Both the companies seemed genuinely interested in resolving this issue. After I DMed my appliance and contact information via twitter, Melissa from Whirlpool called me and left me a voice mail on Wednesday, Sept 3rd, 2014 informing that they have decided to replace the oven. I was told in that voice mail that I should expect a call from Whirlpool on the details of the exchange before end of day on Friday (Sept 5th). I was contacted by Lowes and I informed the Lowes rep that Whirlpool has agreed to replace my oven.I thought I would really be able to make a single update to the post informing the world that Whirlpool really made amends and tried to hard to correct the failures of the past. It is 9/15/14 today and I havent received any updates from Whirlpool about the how/when of the exchange. I made 2 customer service calls to Whirlpool last week. I was unable to speak to Melissa the first time, but did speak with another rep. She told me she will pass the information on to Melissa and ask her to contact me. She connected me to Melissas voice mail and I left her a voice mail. Melissas voice mail greetings suggested that I also contact her via Whirlpools customer service email for faster response. So I did that too.On Thursday 12:37PM pacific, I received a call from Melissa. She had no useful information to share with me. She is waiting for some paper pusher to do his/her job and could not make any promises as to when it will be resolved. My file is stuck in one of Whirlpools many bureaucratic bottlenecks. This is no personal indictment of Melissa it is just evidence that Whirlpools is not serious about customer satisfaction. My experience is not isolated as evidenced not just by this event but also by the number of people ranting on their social media handles. Here was an opportunity to rectify its mistake and win the confidence of a customer back and so far Whirlpool seems to be uninterested in any such thing.IMPORTANT UPDATE (9/16/14): Please share this story via your social media handles. It is important to hold these people accountable for their actions. It is also important that we inform consumer about the perils of doing business with these organizations. Thank you very much. UPDATE (9/17/14): Whirlpools customer supports twitter moniker is @WhirlpoolCare. LOL. They could have demonstrated care by resolving customer issues, instead they removed my permission to post to their Facebook Page. WhirlpoolCare indeed.:) I will be handling this mostly through Twitter follow me at **. I will be using hashtag #whirlpoolsux going forward. I would request that you do the same. Thank you.https://www.facebook.com/WhirlpoolCare.

Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

Buy a new in a box dishwasher, it is not working, not a good customer services, I wait 1 week for a tech to come and fixed, and I will wait to tech to come back with parts to be fix. Company not replace the unit, I pay for something that is not working. Very frustrated for the time waste. 3 day off from work.

Microwave Model # MH1150XMB# - I have had this microwave for 6 and 1/2 years. It came with the condo I purchased. Shortly after I moved in, I noticed hairline crack in the frame near the handle. I have replaced this door once and now the second door has done the same exact thing - formed these hairline cracks in the door frame. This is a defective product and needs to be taken care of by Whirlpool. But you keep denying the problem. No one can afford to replace a door every year. The microwave still works, but the door has fallen apart. The remainder of the microwave works fine.

This washer never worked right. It simply mixes the clothes up with little water. A real piece of crap. See the 2000 other complaints. Time for class action suit.

This Whirlpool Cabrio washing machine just does not do the job. It smells inside and does not get clothes clean, just normal everyday laundry. I usually have to put them through twice. It is supposed to be a water save, but I dont think it uses enough. I use minimal he detergent, yet you can see detergent residue on the clothes after they are washed, I think because there is not enough water running through to rinse clothes very well.

A disaster from start to finish. I would give it zero stars if possible. Purchased from Home Depot online in September, 2020. The first delivery was scheduled for October 11, 2020 at 7am on a Sunday. I spent hours on the phone trying to get the time changed. I was assured it would take place later. That didnt happen. The delivery service Temco called at 6:30a and refused to come back later. I had to make a new appointment. A week later they delivered the dishwasher, left it on the porch, refused to uncrate it or bring it inside the house, refused to haul away the old machine and stole the Dishwasher parts kit that I had paid for which delayed installing the dishwasher. After the machine was installed I discovered the machine did not come with a manual. I was told I had to download and print the manual.When I complained that I should not have to use my paper and ink to print a users manual after paying $800 for a dishwasher. I was promised a check to offset my costs. I was supposed to get a credit for my inconvenience but that never happened either. The first time I ran the machine using the one hour cycle water was all over the machine and I had to dry inside. I was told that I had to use a longer wash cycle so I did the second time. After 4 hours of washing, the glasses had a film on them, even though I rinse the dishes before putting them in the machine the dishes had some debris on them and water had still collected on the top of the glasses.Whirlpool sent a repair company out and the technician said motor pump and display control were faulty and it would probably be cheaper to replace the dishwasher rather than repair it. I was told I would get an email the next day telling me what would happen. I never got the email. During the week I called Whirlpool and Home Depot many times to complain about the faulty dishwasher, stolen parts and the promised refunds for my inconvenience as well as having to print the manual. Calling Whirlpool or Home Depot customer care will take hours and gets you nowhere. A week after the repair person came out I called the repair company to request a report as to what had been done and was told that they were coming back out the following Monday to fix the machine again. Monday, The repair technician came out and replaced the control panel but not the pump. The machine wont heat up to dry the dishes--the heating coil wasnt even warm after being on for 8 min. I am supposed to be contacted again for a 3rd visit!! I have a dishwasher that is faulty (read lemon) and Home Depot wont allow me to return it because their return policy is 48 hours after delivery. Whirlpool refuses to replace it unless the technician says it cant be fixed. Obviously, that will never happen. I should have repaired my old dishwasher rather than waste my money on this horrible machine. Whirlpool used to make fine products but those days are over. How does running a dishwasher for four hours saving energy? My old over 10 year old Whirlpool dishwasher was perfect until the pump broke. The dishes were always clean, dry and came out of the machine hot and sanitized. I am so disappointed in both Whirlpool and Home Depot.

I purchased Duet washer 3 years ago, but it wasnt installed until a little over a year and a half ago. Machine started making loud noise during spin cycle, and eventually would not spin the water out of the machine. I contacted Whirlpool and was told there was a defect in that particular WP model and if it was confirmed by a provided tech, WP would provide the parts for the repair. The tech confirmed the problem, and I was told the repair would still cost over $450, even with the free parts. When I approached WP and asked them to fix the machine since it was a known defect, it was denied that there was a defect.

I had this dishwasher for about a year. It was a great purchase for this model and the price was reasonable. The dishwasher is very quiet and wash dishes wonderfully. The only exception is it does take a long time to wash dishes. The cycle are long.

I recently purchased a Whirlpool Gold Edition double range. After a couple of uses, the top oven thermostat went on the blink. I sat the thermostat to preheat. After 20 mins. and a call to the warranty department, the oven never reached the desired temperature. The warranty department sent a repair person who could find nothing wrong with the stove. I called Lowes and told them I couldnt trust the oven not to do it again (after several times of it happening and resetting the circuit breaker). This would be a disaster if it happened during the holidays when I cook for 20 or more people. Lowes manager said they wanted me to feel comfortable so they replaced the entire range. GUESS WHAT... 2 weeks after having the new one... same problem. I set the thermostat to 400 degrees and when it got to 390, I saw the light blinking. Waiting 10 more mins, nothing changed. I hit the cancel button, reset the bake... the thermostat, when I turned it back on, showed 365... What the heck! I didnt open the oven door. Whirlpool ranges are a piece of crap. I am calling Lowes again tomorrow to return and advise them to stop selling the junk. Dont blame Lowes... They do the best they can with the crap they sell.

I purchased a Whirlpool Refrigerator Model # WRF990SLAM00 in May of 2013. My wife started noticing ice build up on the ice maker in the refrigerator section of this French Door model. We had it serviced for the same problem 4 times and the problem still existed. At this point, Whirlpool offer to give us our money back, and here is where things got interesting. My wife spoke with a Sheila who was to issue a check to a third party company who would then pick up the refrigerator and give us the check. Sounds simple enough, huh? The company was to get the check in 7-10 business days so we bought a new refrigerator, a Samsung this time, and scheduled its delivery for the time frame we were told the non-functioning fridge would be picked up. My wife could not get in touch with Sheila, which was always a problem, and we talked to a Beth who told us that this whole process had not even been started yet. Well, we are having our new fridge delivered and still waiting on our check and for someone to come and pick up this American-made piece of crap! We wanted to buy American, but this is what we got, a piece of crap!!

Worst company for home appliance... I got my fridge repaired from an authorized service person and next day it again stopped functioning. Upon calling the service center again, they said that few more things needs to be repaired once again and for that fridge needs to be moved to their workshop and for that they will be charging 1600 Rs again. Upon asking for the refund for the useless spare part, the rude service person said ek din k liye to chale tha na fridge, fir kis baat ka refund... Such a ** company is Whirlpool that they are not entertaining any complaint on their all India customer care number...

I could echo all of these complaints and more. I just gave up on the heater, junked it, and went to Home Depot and bought a Rheem. Recommendation: NEVER BUY A WHIRLPOOL!

Our Whirlpool refrigerator had to have repair in less than a year after purchase. That was a bad experience last summer and I had to complain through every avenue I could find just to get the replacement part shipped to the repair shop. Now I know it was not too smart on my part, but I bought a Whirlpool washer last September. You guessed it, not even a year old and it is not working. All I am hoping for in this posting is to help some other hardworking consumer make a better choice with their money. It is probably not advisable to buy Whirlpool.

We purchased a Whirlpool side by side from Lowes and an extended warranty. Immediately maybe a month the ice maker froze. Ice container in the door. Repairman said design is notorious for this problem. This was an ongoing problem. They replaced icemaker and it continued. Finally the warranty people told me it could be deemed a lemon if repaired for the same issue 4 times in a year. They deemed it a LEMON and I received a store credit for the purchase price less the warranty amount. I purchased a new LG French door. No issues and its been 5 years. If you have an extended warranty do some checking on the lemon.