I bought the Whirlpool Cabrio topload washer (WTW7800XW2) in April 2011. In May 2012, I noticed the door was broken on both sides. It has now popped up and is broken so bad that it can barely be used without replacing it. I called Lowes, where it was purchased, to quickly be told that there was nothing they could do because it is out of the years warranty. This is just such a copy out to have an excuse, so that they would not even offer any assistance. Also, I paid $2,000.00 for the set; I bought the dryer as well. I just could not imagine an expensive machine like this having such a problem. Prior to buying this machine, I had my washer for 10 years. It has no problem; it was just time to buy a newer model, so I thought!After the store (Lowes) would not help, I decided to call Whirlpool; and the woman I spoke with was even less help. Andrea said there was nothing they could do since it was outside the year of manufacturers warranty. She seemed glad to have this as an excuse. I told her this is too much money to have something like this to happen. I told her it is obvious the door was defective. She said again sorry but that theres nothing she could do. She did offer to sell me a warranty for a year for $327.52. This was too expensive. I asked her what else could she do, and she told me nothing. I asked how much the door was, and she told me $212.00. I feel like I have been royally and deliberately ripped off, and Whirlpool knows it. I say to anyone reading this to please be aware if you are purchasing this product. You will most likely be sorry you invested all this money for it. You will get a companys brand that does not care and will not stand by their product.

I purchased washer (Whirlpool Cabrio wtw5600xwg) on April Fools Day 2011. The first repair was check on 1-27-12. I complained the machine was too loud and clothes seemed too wet - the call was under warranty but tech was unable to verify complaint. So guess what? On Jan. 21, 2013, machine sounds like a stressed jet engine. Now we are diagnosed with a bad gear case for a total repair of $439. Now we are not under warranty and Whirlpool takes no responsibility. Doesnt the consumer have any rights? Do you think Ill buy Whirlpool again?

Literally from day one I had an issue with my Gold Series which was aggravating but at least it was on warranty. Then 2 months out of warranty I had another problem, a leak. Now no water circulation. I think it is maybe 3 years old. What a piece of junk and my Whirlpool washer and dryer? Not much better. I will never buy another.

Purchased a new Whirlpool washer and dryer at Best Buy 6 months ago. We complained to Best Buy and Whirlpool about our clothes not getting cleaned. In other words, my clothes are coming out of the washer dirty. My make-up towels come out with make-up, my husband’s fishing clothes smells like fish and my son’s bike riding clothes is full of dirt. Whirlpool’s answer was the technician is reporting that the machine is working fine. Whirlpool told me to use different cycles and detergent etc. and I have done everything they ask, but my clothes are still the same. I told them this is a defected item. A washer should do its job - wash dirt and smells out. I want a different washer and they refuse to exchange this item for another washer after a second call to technician. Best Buy is telling us there nothing they can do for us. What has America come to? The manufacturers and dealers are selling to consumers and taking advantage of them by not responding to the needs of the consumer. In other words, we the consumers pay for product, take time from work and personal time to reports these problems and we get nothing back, just the run around. Is there something we can do? What can we do? This is very frustrating. We work for what we need. We pay for what we need and we dont get what we need. On the other hand, the manufacturer and dealer get what they need, our hard working money. What can we, the consumer, do to get our hard working money worth????? If anyone knows, please share your experience.

We bought this washing machine in 2013 from Plass, an appliance store in Chicago that is now out of business. The top loading plastic lid that holds the glass piece snapped and broke. I called the company, and they said that there is not a recall but that I could order parts. They put me on hold, and 10 minutes later, I was on the phone with a company in Missouri that wanted to sell me a lid for $219.38 plus tax and shipping. I am surprised to see that others are having the same problem and that there are no recalls from Whirlpool!

After owning the highly recommended Cabrio for only 2 years, I was told it would cost $300 for the motherboard!! I have always used Whirlpool but this machine is terrible. Water saving is not an option when washing clothes. Unless I use the bulky cycle, my clothes come out dry and smell dirty.

Very sad appliance company. I purchased a Standard Pacific Home in June 30, 2015 and moved in Aug 1, 2015. Use my Whirlpool Dishwasher for the first time back in Oct and it was not working properly. Whirlpool scheduled an appointment with Accord Appliance in Temecula Ca and the company was a no show. Called Whirlpool back and Rep Emma was very rude and had to call supervisor to schedule another appointment to repair dishwasher. Whirlpool have sad employees and sad appliance.

We bought the Whirlpool Cabrio set from Sears in February 2010, for our second home. We counted up the weeks we have actually been here since then, it is about 10 weeks. We figure we used the washer about three times per week. So, we have gotten about 30 wash loads from this washer and it dies mid-cycle. We assume the motherboard crashed. It kicked the breaker. Lid was locked and we couldnt get it open. The washer would not power up. Repairman arrived three days later, got the latch opened but couldnt figure out what was wrong with it. He said it is probably a board and it might be better for us to replace. He wants to pick it up tomorrow to take to his shop. I called Whirlpool to complain. I know the one year warranty is up but to get 30 uses out of this expensive piece of junk and not get any consideration from the manufacturer is not right. I wish I had seen all these complaints before I bought it. No Whirlpool ever!

We bought 2 Whirlpool refrigerators for our new home 5 years ago. The first ice maker died 2 years ago at 3 years old. The second has now died this month. We called the repairman in who told us that Whirlpool knew there was a problem with their ice makers, but because they did not cause fires, they were not recalled. We paid $480 later for items that should last at least 10 years, not 3-5 years. We will never purchase another Whirlpool appliance and neither will any our family. A company with this level of ethical behavior that knows they have a faulty piece of equipment and just chooses to do nothing does not warrant my business.

In 2010 we had to purchase a new hot water heater. Went to our local Lowes store to see what they offered. We decided to buy a Whirlpool energy smart electric water heater. It was large, 50 gallon. We have a large family and didnt like running out of hot water so we thought this would be great. Worked fine until yesterday when I kept smelling an odor like something melting. Could not figure out where the smell was coming from until this morning I got in the shower and had very little hot water. Went downstairs and seen the water heater was not working. Got the user guide out to see if we could pinpoint what was wrong. It said no power to control board. I checked the breaker box and found no problems. I got a flashlight to look at the control board and discovered it had overheated and melt the top of it. Have been on phone with Whirlpool nonstop with just a recording. The heater has a lifetime warranty so Im trying to get the replacement part for it that will cost me $115 plus shipping. I am really concerned that with this overheating it did not trip the breaker. Grateful it did not start a fire and worried if we repair it will this happen again and possibly not be as fortunate. I have seen on this site of another complaint with the same problem. Shocked there hasnt been a recall issued. Be careful!

Whirlpool has been an absolute nightmare from day 1. We bought a brand new 50-gallon water heater from Lowes. It did not work. We went back to Lowes and were told to contact whirlpool. We contacted Whirlpool and were told to conduct a number of test and all test passed, so they said we needed a plumber to come look at it. Remind you that this water heater is brand new and has not worked since day 1. They said the plumber would cost $130 and they would pay for parts. Why am I having to pay when my water heater has never worked. Paid the money. Had them come. They replaced a part, did not work, replaced another and it did not work, so the plumber requested a new water heater. Whirlpool refused. What is the point of paying and they are not going to fix it.Whirlpool insisted it was our ventilation even though all test proved that was not the problem. So out of pocket again to fix the ventilation and it did not work. After 2 months of no hot water with a two-year old at home we had someone we know come look at it and fixed the main pipe. Whirlpool took my money and didnt fix my problem. HORRIBLE SERVICE.

Late on the evening of Monday, January 27, 2014, after springing a leak in my 8-year-old water heater, I purchased a new Whirlpool model N50T61 replacement from Lowes. Installation went smoothly and the unit lit off fine the first time. It heated the initial tank of water rather quickly, but the next morning, I noticed the status light on the control unit was not blinking, which indicated the pilot light had gone out. I relit the pilot light, the water heater fired off and appeared to be working properly. 12 hours later, the status light was out again. I relit the pilot, but within 20 minutes, it went out again.On Wednesday, the 29th, I called Whirlpool customer service and explained to the representative what had been happening. He stated that since the status light was not blinking a code, the problem was either an air supply or venting problem, and he couldnt help me. I relit the water heater again and performed the match smoke test described in the owners manual on the vent connection. It did exactly what the manual said it should do, so I assumed that was not the problem. However, while performing this test, the water heater went out again. This time, being right there when it shut off, I saw the status light blink twice about 5 or 6 times before it quit blinking all together. The two blink error code indicated low millivolt signal from thermopile.I called customer service again and explained to the representative what the first person had told me and also told him the results of my test and that this time, I had observed the two blink error code. He asked if I had a multimeter (which I do), so he had me disconnect the wires for the thermopile, connect the meter to the wires, light the pilot and read the voltage. My meter is an old analog unit, and not capable of reading millivolts (which is what the thermopile output is), and I informed the rep of this, but he had me do it anyway. As I suspected, I saw absolutely no reading on the meter. The service rep stated that he believed the error code and decided to send me a new thermopile assembly. However, their shipping department was closed for the day and I should not expect to see the new part until Friday. This was unacceptable, but he stated that this was the only option available to me.After thinking about this situation for a while, I again called Whirlpool customer service and told the representative that I was not satisfied with the solution previously presented to me and that I wanted a return authorization to take the water heater back to Lowes for replacement. The rep stated he couldnt do that, but said that there were a couple other things I could try. He attempted to explain these procedures to me, but wasnt able to do so clearly. He stated he would email the instructions to me. As of this writing, I still have not received the instructions.In the meantime, I did some internet research and found that Whirlpool water heaters have numerous chronic problems, including the issues I was experiencing. I decided this was not a product I cared to own. I called the Lowes store where I purchased the water heater and spoke with the manager. I explained the entire sequence of events to him, and he told me to bring the water heater back for a full refund. Since my local Lowes store only sells the Whirlpool brand, I took the money and purchased a different brand of water heater from another home improvement store. Needless to say, it will be a cold day in hell before I ever purchase another Whirlpool product.

Whirlpool’s customer service is one of the worst I have encountered. They consider a 6-7 year old $1500.00 range to be old! I said to her, “Wow, if the population was to throw their Whirlpool appliances into the landfills after 7 years, this would be quite a horrendous situation.” I think its disgusting for a company to build appliances with a shelf life of 6-7 years and with only a 1-year warranty! What a horrible brand! I will never buy another Whirlpool brand product ever again. You spend $1500.00 on a range oven and then around 5 to 7 years the control board blows out and costs another $500.00 to replace plus a service agents fee to remove and install.I asked the Whirlpool agent if I could get the control board discounted and she refused and said, “I am sorry, we are unable to help you.” Pathetic! Their cost on these boards is around $120.00 or so. I was told by an appliance service rep they could discount that $500.00 board even half and still make a decent profit. Do not ever buy Whirlpool. Go with other brands instead. Their customer service policies are horrible. Your hard-earned money will be buying an appliance with a 6 to 7-year shelf life before major repairs.

My oven had been temperamental since day one, then got worse over time. I do not use my oven that much so was not really worried or alarmed until a tray of cookies caught fire. It was set at 350 and jumped to 525 on its own. (I bought an oven thermometer to monitor) Minor burn taking tray out but all okay :-). Contacted Lowe’s where we bought it and they would do nothing (note: at this point the oven is 15-months old and out of warranty). Advised me to contact Whirlpool. Did that - they sent out a repair service and they determined it was the temp. sensor. It is now April 2014 and I am still waiting for the part (this all started Sept 2013). I have since talked and wrote to Whirlpool for this to be resolved and also asked that the range be recalled due to fire hazard at the least! When I spoke to them in December, they said they could give me ‘50% off the part’. Remember I am still waiting for that part, lol! After writing corp h/q, they said “Sorry, since we cant get the part why not have someone come in and take the old part out and have it rebuilt.” I ask you Whirlpool w/q would you be happy with that??? Will post any follow-ups... would love to hear from anyone else with this problem - model # GFE461LVS. Great day everyone. :-)

Just bought a Whirlpool stove (WFE540H0ES) from Home Depot. Oven gave off so much heat around the handle that I burned myself opening the door... Tech came out said it wasnt supposed to do that. Called into Whirlpool to get clearance for a replacement and corporate says no to the replacement because that is normal. Thats BS! If that is normal DONT BUY A WHIRLPOOL!! BTW... They are owned by Maytag.

I purchased this machine from Sears on 04/23/2016 and have had nothing but problems and issues with it. It is loud and makes different sounds every time I use it. It has overfilled and underfilled with water a few times, the machine shuts down while washing and I have had to restart the machine. Half the time the clothes come out covered in soap and I have to put them through another rinse cycle. My bedding always has to either go through a second rinse cycle due to being covered in soap or I have to rewash it because it is all packaged together in the fitted sheet and never got washed. During the spin cycle it sounds like it is getting ready launch into outer space and it vibrates excessively. On numerous occasions I have had to untie my clothes as they are tied in knots. There have been times that I had to put the clothes through another spin cycle because the clothes contained too much water. The final straw was last week (03/27/2019). I washed my sheets and they came out bundled up in the fitted sheet full of soap stains and I had to rewash them. When the sheets were done I put the comforter in the wash and started to clean the house. When I went into the laundry room the washer was not running but the wash light was on so I opened the lid and felt the comforter and found it to be dry. I closed the lid and pushed the start button. After a few seconds the washer shifted to rinse without even washing the comforter. When the washer stopped running and the ready light came on I removed the comforter, unplugged the machine, shut off the water, disconnected the water hoses, placed the machine on a dolly and took it to my scrap pile. I could not find any Whirlpool washers with any good reviews so I purchased a Speed Queen with a 5 year parts and labor warranty.

I have a Whirlpool built-in double oven. It is 7 years old. The top oven has overheated 3 times with food in it and it locks the door. The oven beeps and says, Too hot, and locks the door. Luckily I was in the kitchen when it overheated, so I could turn the oven off. After turning the oven off, the oven has to cool off before the door will unlock and the food can be taken out. By then, the food is really burnt.I called Whirlpool to see if there is a recall and they said, No recall, and the oven was out of warranty. So I called the repair shop. They said it was the control board and they were not sure they could get a new control board. I may have to find someone that can rebuild this control board. They said not to use the oven. It could cause a fire. I would think that they should recall these ovens. They should have a safety switch that shuts the oven off if it overheats like mine has done.

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...

Extremely quiet machine. I love that the silverware wrack is situated across the front of the door giving plenty of space for lots of silverware. This leaves even more room in the already large washing area for pots, pans, dishes, bowl, glassware & more.

Purchased in January of 2014: Brand new Whirlpool WOS51EC7AS01 model oven - interior bottom metal has buckled causing the enamel to crack and break off from oven bottom. I registered all my new appliances immediately for warranty. When this happened after the fourth or fifth time baking in the oven, I called Whirlpool to get a service person to look at it. First person Whirlpool scheduled to come out refused to even come out, without looking at my oven. He said he knew we did something wrong? They immediately set up a second service person, after two weeks waiting for an answer; I had to call him (twice). He said that his report and pictures sent into Whirlpool shows normal use and there is nothing wrong with our oven? So, Whirlpool will do nothing to repair the oven? We just spent almost $4,000.00 on all new Whirlpool appliances, and this is how we get treated? WOW! Never again will I ever purchase a Whirlpool product. The enamel is gone in spots from our oven floor. How long do they think that will last with no protective coating on the oven? Terrible customer service.

I installed my new water heater in 2012. Within 3 months, it was not producing hot water. When I called, a helpful person at the Whirlpool warranty line told me it was because there was too much cold water being mixed into the hot water coming from the tank. I hung up... Called again and was told that they would be able to get someone in 2 weeks out to my house to check it. I told them that was not acceptable. I hung up... I called Lowes, where I bought it. The person on the other line finally, after more than 1 hour, was able to get a repair person out there within 2 days. I had to pay the fee to have the guy come look at my hot water tank, and tell me that he hated Whirlpools. He called Whirlpool, 3 times; he was hung up on 2 times. He explained what had happened was I had a hot water leak, that it probably it was overloaded, the thermostat control everything else was fine. However, that I had installed the heater myself not a professional. Therefore it was not up to NATIONAL code; therefore, Whirlpool refused to honor the warranty. So, short version, in order to get the tank repaired, I was supposed to spend an additional $300-$400 to bring the heater up to code for them to honor the warranty. What you ask made my heater out of code? It is outside in my utility room, and the flue was cut to fit and the OUTSIDE vent pipe was not above the roofline. It didnt matter that it is not in an enclosed space, that this was nothing to do with the reasoning the thermocouple went out.I simply turned up the heat, so far so good. Will I ever buy another Whirlpool? No. I have a Whirlpool fridge bought before the hot water tank situation. The ice maker went out within 6 months of purchase. When I called to have it repaired, the service guy stated he hates Whirlpool. The piece he had to replace was plastic that was replaced with a metal piece that should have been metal to begin with.

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.

We purchased a whirlpool gas dryer 30 years ago this past February. Its still going strong with 30 years of continuous use!! The only service ever required was a belt change I did myself 18 years ago. Not too bad whirlpool!!

I have the Cabrio washer that is only four years old. It is leaking oil and is very loud during the spin cycle. I paid $800 for this washer and am extremely frustrated that it didnt last longer than this. I contacted Whirlpool customer service and had no luck since it is out of warranty. Due to the high number of complaints with the same issue, please consider a class action lawsuit. Thank you.

I purchased a new Whirlpool stainless steel smooth top range model #WEE745H0FS and it was installed the day before Thanksgiving, 11/22/17. The oven door handle was broken on inside by installers. I called Whirlpool warranty on 11/24/17 and requested a repair. A repairman came the following week two days late. He said he needed to order a part. After calling the “Whirlpool approved” repair shop multiple times over the next two weeks, I was told the part was backordered. Finally, yesterday, 12/13/17 the repairman showed up an hour later than appt. time. He took the oven door apart again and the new part didn’t fit my oven door. He had carelessly ordered the wrong part. I was told he’d put a rush on the correct part and that it would be here 12/18/17. I will never buy another appliance from Kelley Appliance in Augusta GA nor another Whirlpool product. I have had to use duct tape on my brand NEW oven just to use the oven so it doesn’t fall apart when opening.

This new oven came with my house. I like the oven but hate the aqua clean feature. It is impossible to get the grease off. I cant reach the back sides or the back. I scrub with all my might on parts I can reach but the baked on grease is back with the next use. The aqua clean feature is only good for light spills on the bottom. I like a clean oven. I am now looking to replace a practically new oven which will run me about $2000.00 which I am not happy about. I highly recommend the high heat cleaning feature ovens. I also developed a pitting area on the bottom the size of a quarter & I dont know how that occurred. Buyer beware of aqua cleaning features.

I bought a Whirlpool Cambrio washer/dryer set last year. I hate them. They dont get the clothes clean, let alone wet! I couldnt believe it! I put my grandsons bib in the wash and it came out completely dry with the stuck on food still there. My husbands shirts still smell like the cologne he put on! I asked a Home Depot sales person about this and he says, yeah, we hear that a lot. !!!!!!! Im going back to a washer with an agitator so that I know my clothes are being cleaned. This whole water control business is insane. Whats the point if you have to wash the clothes several times to feel like they are marginally clean? The problem is that the industry has decreased the amount of models that still have an agitator so my selection is very slim. First and LAST time I ever buy Whirlpool.

First, I was put on hold by the first female for 44 minutes, and then a second woman finally answered, and said she didnt know why she would send me to her, because she was in the sales department, and she put me on hold for another 25 minutes. I finally had to go, because I had an appointment. When I got home, I called back, and got a man by the name of John, and at least he recommended he could schedule a repairman. The problem I told him is, the inside wall of my refrigerator has 2 cracks on the side, and a crack on the back wall. I dont want a repairman to come, just to tell me he cant put 2 new walls inside of my refrigerator. I could not find an email, so I could email Whirlpool about this problem, and definitely, they were of no help. I bought the refrigerator at Lowes late 2003. I have never, in my life, seen the inside walls of a fridge do this. I spent a lot of money for this, for it to crack on the inside walls. It does not seem like something is right with this.

Had to return my first 2019 purchase due to refrigerator freezing food and imbalanced top doors. I was unable to get straight answers from Whirlpool and so the mgr at BB gave exchange same problems except door not as off. Cheap product make/model. A class action lawsuit from 2016 has occurred and the company continues to distribute the same issues in their new make/model.

I purchased a Whirpool fridge five years ago. To date it has had 7 repairs. The latest round has lasted over five weeks and the expensive warranty I also bought is about to run out. The repair man is on his third repair and I havent had refrigeration for five weeks. In the meantime they wont replace the fridge, and it takes two weeks between scheduled visits by the authorized repair man.

Do not under any circumstance end up with the Whirlpool fabric washer and or dryer in your dwelling to wash and dry your clothes. The washer, model # WTW7000DW0 and dryer, model # WED7000DW0. I am so upset with these units and the company I bought a 5 year extended warranty thru. I cannot put down in words what I think, because this review would not be published. Do not even accept these units, even if they are free. Even the repairmen who have been here said they would not buy these Whirlpool junk washer and or dryer series. They acknowledged the problem and said nothing could be done even though there is a legitimate problem. Not only is there a problem with the washer, the dryer as well has serious issues. All washes have to be put on the deep water cycle and some loads have totally dry spots on clothes where the clothes did not even get wet after the washer went thru the complete cycle. Also, get this, this washing machine even has to be cleaned itself with a cleaning tablet run thru a cleaning cycle. What happens are the clothes get a nasty, slimy, white muck on them. Even, immediately after the washer gets cleaned, sometimes the clothes 32nd up with this muck on them again. If you do not see this muck on your clothes before putting in the junk dryer, then the clothes have to be washed and dried again. This washer is supposed to be efficient, not a chance. It gets costly having to purchase the cleaning tablets and the washer(28th only two people in the household) has to be cleaned a lot more than what the manufacturer says and I called and asked. Pure junk, do yourself and even your enemies a favor, stay away at any cost, and like I said, even if they are free.

I am so disappointed, angry and tired! Unfortunately, I listened to the salesperson regarding this feature and bought it hook, line and sinker! The Aqualift self clean system is a joke! It only cleans the bottom of the oven and that is after you mop up the water left in the bottom and scrub it. No amount of scrubbing even touches the sides, back or window, even after using the Aqualift feature 3 times! I spent hundreds of dollars only to be down on my hands and knees scrubbing to no avail. I have not seen 1 good review regarding this system. Shame on me for believing a salesperson and shame on me for not researching first. I will not make this mistake again!

In the last 6 years I have had two refrigerators each lasting three years with major repairs from day 1. I am on my 6th repair for my Whirlpool Model WRF89SDAM02 purchased in October of 2013. WHAT A PIECE OF JUNK.

I have had to replace my Whirlpool 50-gallon hot water heater 2 times. First time it broke, it caused thousands of dollars’ worth of damages plus Im out a $760.00 deductible. I had the last one just over 1 month and couldnt exchange it at Lowe’s because it’s a few days over a month. So I had to get return authorization before I could return it again. I went through speaking to a hateful CSR. After calling back again, the lady, a real nice lady, helped me. I will never buy another Whirlpool product again, and if anyone is smart, they will stay away from them too. Hateful, hateful CSR. Beware.

Refrigerator stopped cooling... Paid $200 to have it diagnosed... Cost more than a new refrigerator to get fixed...$14,000. Refrigerator was 7 years old, energy star. How can it be energy efficient if it was made to last only seven years? How much energy is wasted making new ones to replace the broken ones, that cost too much to fix. Energy star. What a scam.

I love the way the clothes are clean when I wash them. I also love how well they are rung out when I get them out of the washer to be put into the dryer. The washing time isn’t too long either as compared to other washers I’ve used where it took almost an hour to wash and the clothes didn’t seem as clean.

We purchased a Whirlpool (gas) range with double oven, in April of this year. We found that the upper oven over heats, on the right side, and therefore burns or bakes unevenly.The repair company will be out for the fourth time tomorrow. They have been very nice to deal with, but really have not been able to repair or come up with any definitive plan of repair action.

The broiler came on its own during the night. We went to bed at midnight. 4:30 in the morning woke up to a smell, the broiler was going wide open. It had melted the handle off the front of the drawer. There are cookie sheets in the broiler. We dont use it, we have never used it, it was so hot Teflon on the cookie sheets burnt off. The side of the stove was so hot I couldnt touch it to get behind to turn off the gas. It almost burnt my house down. The carpet and the wall are black in the back.

The refrigerator is a Whirlpool Model #GSC25C6EYW0. We purchased it on September 17, 2013. So far we had to fix the ice maker, the drawer broke, the refrigerator cools unevenly. They tried to fix it but cant. Therefore, I cannot put tall things on the top shelf. Now it is not cooling and I have to repair or replace it.

I had sold appliance for ten years. I purchase a Whirlpool Cabrio 2010. After two years started rusting. It is rusting on the outside and now on the inside, that I cannot wash delicates or whites. I so disappointed. I had lots of confidence in Whirlpool. The model is wtw7300xwo... I call talk to whirlpool but got no help. Now I going to need to purchase a new washer. It will not be a Whirlpool.

Im very frustrated. I bought a Whirlpool Refrigerator for nearly $1300 in Sept. 11. It is a side-by-side Model #ED5KVEXVL00. The refrigerator side started warming up to the point that we noticed. We put a thermometer inside to confirm; it went up to nearly 60 degrees. We tried cleaning any dust underneath from the coils and even unplugged it for a while. The compressor appears to be the potential problem. Sears is not sending a repair guy for 2 WEEKS (It is a hot July here in NY)!!!!We are saddened that Whirlpool says it is out of the one-year warranty - so now we are facing the choice of a large repair bill or buying a new refrigerator. What a waste of money... Its not even 2 years and it needs service or a dumpster. Shame on Whirlpool for not standing up for customers when clearly there is something wrong with this machine so close to the warranty and so new. Sears and Whirlpool - youve lost me as a future appliance customer!!! :(

I have been using Whirlpool brand of appliances for over 40 years. They have always served me well and very dependable. Im a semi retired HVAC contractor and also installed Whirlpool heating and air conditioning systems in peoples home, also very satisfied with the results.

Whirlpool Gas Range WFG540H0es - Purchased 2 months ago. After 2 weeks there was a spill. The black burner caps are powder coated. After cooling we washed it with dish detergent & a sponge. The powder coating came off. Called the company. They replaced burner caps. Last week there was a spill and it stained the burner bases which are powder coated in a silver color. We tried 409 cleaner, Windex, dish detergent with a sponge. Could NOT get the stain out started removing powder coating. Called the company they ONLY guarantee cosmetic appearance 30 days. They wanted $139.00 for a new set of burner bases. I am going to go back to Lowes & see if we can return this Whirlpool range.

Whirlpool Cabrio Platinum Washer Model WTW8800YC1 - I bought the Cabrio washer and dryer pair about 2 years ago at Lowes. About 5 weeks ago the lid fell apart. The hinge area came loose so now there are three pieces to line up (glass lid, metal arm, plastic frame), the fourth piece fell off completely. If you are successful at lining them up you can push the lid down and set a weight on it in order to wash. My first repairman said it was common issue. He expedited a lid. Three weeks later I called to find out when it may be repaired. He said he hadnt gotten the part from Whirlpool. I called Whirlpool... nice lady told me the part was on back order but should ship the first of the week. So on week 4 after not hearing anything I called a new appliance repair person. It is going to cost about $280 dollars to repair. This is one third the cost of a new washer??? I fight with this machine every day to get it to wash.

No response from Whirlpool, but I did find out what the rust was. Instead of using stainless steel or plastic or rubber, the inside light frame is made of a cheap metal that has rusted and is literally falling apart, sharp and very rusty pieces were falling into the washer tub. No wonder I find holes in the clothes that werent there before washing. I removed what I could, including the part it should hold, a plastic plate that covers the light, protecting it from moisture. My husband covered it with electrical tape to prevent injury and possible electrocution. I contacted Whirlpool, but they have ignored my questions and have not answered. They do not have a replacement part for it (stated on their parts website) They give you no solutions to a problematic appliance that should have been recalled and taken off the market due to safety issues that have caused injury and possibly worse.

After months of careful research and comparison, I finally bought a pricey (over $2K) Whirlpool refrigerator with a bottom freezer and French doors with water dispenser on top. I really did not want any fancy features, just narrow doors because of my small kitchen, and a fridge on top because of my back pain. Since the date of purchase in May, 2014, I have had 4 service calls. The first was covered under warranty, but no cause of the sheet of ice collection and underside water leakage was identified; I did, however, receive a somewhat patronizing lecture on the importance of thorough reading and comprehension of the owners manual, and a statement that most of my service calls are for customer education. A follow-up service call, a few weeks later and also covered under warranty, identified the cause of the ice collection and water leakage: a faulty duck bill little piece of plastic in the drainage system that is a problem well known to Whirlpool. In mid-June of 2015, the ice maker had to be replaced, to the tune of $360.00. Today, I had a service call ($103.00) and received an estimate of $405.50 to replace the broken freezer drawer slides, which prevent the freezer drawer from fully closing. I will be applying that $405.50 to the purchase of the simplest model, non-Whirlpool refrigerator available, and have the Whirlpool hauled away. Besides the problems noted above, the center of the refrigerator freezes the food, while the freezer compartment arbitrarily defrosts. There are alarm icons that go from blue to red to alert you of the need to replace the (expensive) ice and water filter, refrigerator air filter and crisper freshener. Alarm bells ring to inform you that the doors have been open too long, but nothing alerts you to the fact that the freezer door is not completely shut, or that the freezer has gone into defrost mode because someone inadvertently brushed up against the control panel and changed the settings, or that water is pouring freely out from underneath the appliance. I have had to change my buying habits because fridge holds at least 15% less food, even though it is the same cubic footage as my previous (top freezer) one. Freezer contents easily slip down behind the top freezer drawer and jam the door open. I have to take most frozen boxed items out of their original containers and pack them flat in freezer bags to get enough storage. Some tall bottles do not fit anywhere in the refrigerator compartment, and have to get put in sideways. Even in the absence of mechanical problems, using this refrigerator is like packing and unpacking a suitcase many times a day. While Whirlpool customer service personnel were not overtly rude, there were dismissive and condescending overtones in some of the questions and directives I received from them, and another insinuation that service calls would not be covered under warranty if they end up being for the purpose of customer education. The extended wait (7+ days) for appointments with a Whirlpool-certified appliance repair company, along with the customer education exclusion, were absolute deterrents to the purchase of the extended warranty. Besides my personal disappointment and disgust with the purchase of this appliance, I am sad to see that the Whirlpool brand has slipped so far in product design, quality and customer support.

We bought a Whirlpool range with glass cooktop and convection oven to replace a 20 year old stove which had served us reliably but was beginning to look a bit dated and worse for the wear. The new range was installed in February, less than 2 months ago. Today, while I was preparing Easter dinner and had a ham in the oven, the cooktop elements refused to heat, even though the cooktop on light was lit up. We followed all the troubleshooting tips we could find in the user manual and online, but nothing worked. We decided to do the rest of the meal in the microwave and just finish the ham in the oven (which had been working). Then the oven failed, and would not heat back up.As a last resort, we pulled the range out and unplugged it, to perform a hard reset of the electronics. (This was recommended in some of the online troubleshooting tips.) No joy. Both the oven and cooktop elements will not heat, even though the lights on the control panel light up. Now we have to call a service technician to come fix it in the middle of a pandemic. How can a brand new and expensive range be less reliable and less useful than the cheap 20 year old stove we just got rid of?

I had my entire kitchen re-modeled in May of 2013 and purchase all new Whirlpool appliances. I work for Standard Pacific Homes and purchase the identical appliances we provide in our homes. I am so disappointed in the refrigerator. Two months ago it stopped making ice and I was told to replace the filter and it would be OK. I did that and still no ice. I bought ice trays. A couple of days ago, I came home to find water on my kitchen floor coming from under the refrigerator. I called Whirlpool again and no real help.... Told me to call Lowes. I called Lowes and they gave me 3 more numbers to call for service. None of those service providers had any available appointments and told me to call Whirlpool. Meanwhile my refrigerator is standing in the middle of my kitchen so I can keep the water mopped up. The refrigerator was so difficult to move. Getting the feet moved up so the wheels could touch the floor took an hour and I ended up with bruised hands. My lesson in this is to buy a better brand next time and go top of the line. I sell these to our buyers at Standard Pacific Homes everyday..... Wish I could believe in the product.

My husband and I remodeled our home and needed a new refrigerator... I wanted to try a Samsung, but after exhaustive research on my husbands part, he insisted we purchase a Whirlpool fridge... From the get go, I have regretted that decision. The main reason being the door on the L side of the fridge does not close completely. Sure, it alarms for a time, but what about all the times I close the door and leave the house. I have had to dispose of more groceries than I care to think about... Never again will I purchase anything by Whirlpool!

Offers a long-lasting, high-quality finish that resists scratches and rust. Provides smooth, efficient operation and reliable combustion efficiency. The ECM motor provides computer-programmed airflow for greater efficiency, humidity control, reduced noise levels and increased comfort. 2-Stage Gas Valve System Allows the furnace to operate at a lower output setting to more efficiently control your home’s comfort in relation to the temperature outside. Reduces gas usage by 30% on most days. Durable, Baked Polyester Pre-Painted Steel Cabinet Offers a long-lasting, high-quality finish that resists scratches and rust. Aluminized Steel In-Shot Burners Provides smooth, efficient operation and reliable combustion efficiency.

Purchased Whirlpool Microwave 1.6. The design has 5 BIG flaws. 1. Too large in depth, cabinets on each side cant open. 2. The one light under unit is so far to the back wall, you need a flashlight to cook spaghetti or use stove. 3. Too large in height, cant get a big pan on your stove. 4. Top of unit is open so much, if you spilled something from the cabinet above it would go right inside the works. 5. Instructions are hard to read & figure out, the wall hanging support is just one piece and if you dont have 2 main beams youre out of luck. GO buy a GE, put it up in 1/2 time & good & secure and works great. Has 2 lights on each side under unit. Fingers over the holes at the top. 1 inch shorter, 1 inch thinner. To my surprise the turntable is even larger, go figure.

We bought this washer on 9/05/09. Recently, it sprung a leak due to a worn out seal that the repairman said would cost more to fix than just getting another washer. You would think this might be cause for distress, but I literally jumped in the air and clicked my heels with joy! This washer has been nothing but a pain. First of all, I have to pre-soak every load before washing or the clothes come out just as dirty as they went in. I would set the timer on my stove to let me know when the 40 min soak cycle ended so I could change it to wash. Then I reset the timer for another 40 minutes. I also learned the hard way, that using any kind of heavy duty setting would turn towels into a pile of yarn. This washer cost $998, and guilt is the only reason I didnt replace it years ago. Ding Dong the washer is DEAD!!!

I bought a brand new Whirlpool fridge 3 years ago and it went out completely while on vacation. I lost 5 black bags of food. The compressor went bad due to it leaking Freon or whatever it is called. This is a recall on most models but they say not on my model so nothing is being done. So I will never buy another thing made by Whirlpool again.

The washer and dryer, Cabrio, machines are not even 4 years old and Ive had to repair four different things! Literally just replaced idler pulley today, went to put a load in wash and F1 code appeared. Control panel, 350.00 for whirlpool or a technician to repair! 285.00 for part. I called Whirlpool and was not offered any apology. Never again will I purchase Whirlpool crap appliances!

My Duet washer is just 3 years old and has had light use as there are only two people in the household. After just 3 short years the machine stopped working. We were told it needed a controller board and new valves. The cost of the repair was quoted at $733.00. This is far more than we paid for the machine. So we called customer service and at first they thought they could sell us a plan for $350.00 that would cover the repair but it was denied by the supervisor. So zero help, absolutely nothing. Now the backdrop here is that our last Whirlpool (same type) is still in use with our son no repairs in 15 years. Does anyone reading this think we should buy another Whirlpool or recommend it to our Friends and family? I think a Maytag is in our future. Whatever happened to companies standing behind their reputation in America?

The stove is okay except it scratches on its glass surface fairly easy with the non-stick pans. Also wished it had a self-cleaning oven. Its not the easiest to clean on the inside of the oven. The knobs are easy to use but its hard to navigate knobs to low to keep food warm rather than cooking at a low temperature. It has strong exhaust fan that really does its job.

I am very upset with this company. I bought my fridge two months ago from Sears. The fridge is leaking water and Im having a lot of problems with the freezer and the ice maker isnt working at all. Ive been trying to reach the company but they always leave me hanging in the phone and never answer and keep hanging up. I am very upset with this company. I wasted a lot of money for nothing. Please people dont buy fridges from Whirlpool and dont waste your money.

We purchased the Whirlpool Cabrio washer and Dryer May 2017. First, this washer is SO LOUD! Honestly, NEVER had a washer that is this loud on the spin cycle. My second issue is, that when I wash my blacks, they have white splotches streaks on them. I use ALL clear and free liquid washer and Downy softener, so I stopped the softener, and still the white streaking. Ive since will use the additional rinse on during the wash, but still leaves white streaks. After 3 separate rinse cycles, no streaking. This leaves me thinking that with the lighter colored clothing, there is probably streaking as well, just can see it - my conclusion is that the clothes arent getting cleaned properly, or rinsed. Another issue is the dryer. First, takes longer than all my previous dryers, even the set 110 mins for towels on high, still takes longer. My washers are not packed tight with clothes either - its just my husband and myself - not a lot of washing. Also, I noticed a crack in the inside dryer/drum where it looks like the paint is chipping and cracked. I used some high heat touch up paint, and it did not help. Needless to say, what I thought was an good reputable product, turns out to be, not so good.

Inconsistent freezer and frig temperatures, with vegetables and fruits freezing in the fridge, even when temperature is properly set. Freezer control knob and vents too easily blocked. Unit is very noisy.

I purchased Whirlpool Microwave/Convection Oven a little over a year ago. It needed repair four times and the latest repair debacle appears that it will take ~5-6 weeks to get it repaired if the part that comes in works. The microwave model number is GMH6185XVS1. I will never buy another Whirlpool appliance. I spoke with Whirlpool (not the extended warranty company to which I was referred), and they refused to help, period.The extended warranty company (although very nice), werent much help and will continue to attempt repairs until the price of the repair(s) exceeds the value of the microwave no matter how it inconveniences my household.

We have tried to have our refrigerator fixed 3 times. Same problem every time ice build up in the freezer. Clearly after reading all the reviews Whirlpool has made a very poor quality of a product and they dont care. Hopefully others will read these reviews and learn that its not worth it to buy a Whirlpool.

We bought this 26 cu ft fridge from Nebraska Furniture Mart in April 2017. In November stopped making ice. Was repaired. Now it’s not working again. Multiple enquirers shows this is a common problem with this fridges. I’m debating whether it’s worth the effort to repair it or just put in junkyard. WORTHLESS piece of shiny metal.

I purchased a Whirlpool washer in March 2007. That washer is now leaking from the bottom. I called Whirlpool. I was told that the machine only had a one-year warranty, so repairs would be at my expense. The CSR then offered to schedule a service call for me at $139, which I refused. A few weeks later, I received in the mail an offer for an extended warranty on my Whirlpool washer.

The Whirlpool microwave has been very reliable and efficient. I like its multiple functions, from heating up leftovers to defrosting meat and poultry, baking potatoes. All the functions are easy to use.

So after having the old white standby refrigerator and stove from the late 1970s, I figured it was time to upgrade. I have had theses appliance for TWO MONTHS! And they are starting to rust! I dont want to complain, I want a solution. Is there a law suit or advocacy to get our money back? I even bought the 5 year warranty, but found out that it is considered cosmetic!

We bought a top loaded Whirlpool washer, model WTW5000DW2 last May from Lowe’s for a summer beach cottage. It has been a terrible experience. There was a 30 day warranty from Lowe’s which unfortunately we missed because we had not moved down for the summer till after the 30 days. Working through Whirlpool, they sent an independent contractor out 5 times over the summer. Control panel was replaced twice. It never worked properly. I’m now back for the summer, and it still does not work. Do not buy this washer.

I like my machine even though there is no agitator. It is a top loader so it does not smell. It is a water saver which, when I first got it, I thought that it could never clean the clothes in that small amt of water...but it does clean the clothes very well.

I loved the Whirlpool Refrigerator! Nice size and always worked well. Had to replace it after condenser quit working. This current fridge is unhandy in many ways. No light in the freezer and size is too small. Had to fit into existing space, but does not have as much storage space as the KitchenAid that fit in the same space.

Whirlpool microwave 1163XVS - I purchased a new home and a Whirlpool microwave in May 2010. The microwave has all of a sudden stopped heating! Turns on, spins, counts down, lights up, etc., but will not heat. Found this site by trying on my own to detect a possible reason and Im shocked to see these many complaints of the exact problem. Unbelievable, should be class action suit maybe for continuing to take money from consumers for defective product that Whirlpool knows about and appears to not take responsibility. Ive read enough, not even going to call for repair. Im buying another brand and spending more wisely this time. Thanks for the heads up. Shame on Whirlpool.

The Whirlpool duet model wfw9150ww01 washing machine is a piece junk. After using it for two years, the bearing has gone out on it and it sounds like a freight train. It will cost $600 to repair it. We only paid $575 for it. What a rip off. Whirlpool makes junk only. Buy something else.

The machine pass all the cycles but the clothes are only very wet and still dirty.

I purchased a Whirlpool Cabrio top loading machine approx 3 yrs. ago. When I first bought it, the machine was super quiet... loved it. I loved the capacity of it. About a yr ago I noticed it started making all kinds of noise, we cant have a conversation downstairs because its so loud. Turns out the bearings are broken. The technician was nice enough to explain to me that its a common problem with those machines. However, Whirlpool is not willing to stand by their product and repair it free of charge. Any other product would of been recalled and repaired. That goes for cars, baby products, and so on. But not Whirlpool, I called and spoke to Andrea in Michigan who told me that there is nothing that they are willing to do. After reading the other reviews and their terrible one star average rating it doesnt surprise me. Shame on me for not researching this product before buying. I hope this saves someone else from making the same mistake. In case your wondering, it cost me $117.00 to have the tech look at the machine. The labor would of cost $125.00 and the part is $251.00........

Reading the many reviews of malfunctioning washers and other appliances, I wonder why organizations like Consumer Affairs and Consumer Reports do NOT help the many cheated customers form a class action lawsuit or boycott or some other means to effectively organize and force manufacturers to return the full cost of purchase, taxes, shipping, moving and repairs for 5 years for every product. The manufacturer have NO consequences for selling shoddy, malfunctioning but terribly expensive products. We are all being taken for fools by the corporations.I was stupidly brand loyal and bought a Whirlpool Duet front-load washer and dryer because we had to leave our perfectly good 28-yr-old Whirlpool washer when we sold our house. The first set of instruction is to pull the electric cord from a small hole in the back of the washer. No amount of pulling would budge the cord. Finally yanked with all my strength, heard a snapping sound and 12 of cord came out. Then no more pulling, yanking or tugging would produce another inch of cord. So I took off the top of the machine and found the cord tightly wedged in the fork of a plastic thing that looked like part of a stabilizer for the drum.A similar plastic thing on the other side was broken at the fork, the snapping sound I heard. Freed the cord with lots of effort, but it was still firmly stuck way down inside. Removed the back of the machine, found the cord stuck inside a circular thing with one tiny opening. Took lots of time and effort to free the cord from that, but it was still stuck. Finally managed to reach the plug, which was firmly anchored to the bottom of the frame with an orange lanyard. Cut the lanyard with a knife to finally free the cord. This had to be an act of sabotage by an assembly worker, as no way could the cord accidentally jam itself into 3 different places too small for the cord to slip in, and it certainly didnt tie itself to the bottom of the frame with a lanyard.The hour it took to free the cord was just the start of troubles with this machine. It did start and kind of tumbled clothes in an odd fashion, but when it went into spin cycle, it literally jumped all around the room, almost jumping out the door. The whole house shook and I feared the floor would collapse. That machine must weigh well over 100 lbs. even without water and clothes. Next load I tried delicate cycle which had a slow spin cycle.Same result, even worse. I had to wedge my body in the 10 space between washer and dryer and press down with all my 170 lbs. to keep the machine from doing serious damage to the dryer, walls and floor. I contacted seller, Lowes, and they said call Whirlpool. So I did, but no response. Before buying that machine, I read many horrible reviews of Whirlpool Duet machines, but I have only owned 2 washers since 1967, both Whirlpools, so I had strong but stupid brand loyalty.

I have a Whirlpool Duet front loader. Sick of it since I bought it! Not enough water to wash & rinse clothes. After consulting sites on internet, husband decided to try adjusting part. He just took off the 3 screws & lifted top off. On the outside part that has a white plastic housing, he turned the longer screw 2 1/4 times clockwise. EUREKA! We have more water! You may need to start out adjusting 1 turn & work up till you see a water level you like. Just dont let the water come over the wide rubber water guard.

I have always like the Whirlpool brand in general. It is a well known company and the products have always been of quality. I will say that recently I discovered that Whirlpool will only allow their own technicians to work on more current washers and driers and that is concerning since I have always used a technician I know and trust.

Whirlpool Cabrio Washer WTW7800XW2 - After buying my American made washer..... at nearly $900 with extended warranty about 2 years ago. This week noticed small cracks in plastic that surrounds and holds glass lid. Now lid will not sit flat and glass is emerging from encasement. Called extended warranty claim center and was told it was a cosmetic issue. Called Whirlpool, and was told they were unaware of this flaw, even though countless websites, chat sites, and Youtube. My frustration is how they claim to be unaware of this flaw and refusal address it, after countless consumers have called. I would be willing to start a class action on this matter!

In 2011, I bought in Croatia, for the start, 2 washers (model 3LCHW9100WQ) and 1 dryer (model 3LCED9100WQ) and opened the first self-service laundry in Pula, Croatia. Since the beginning, I had problems with the gum (black). After the washing cycles, you could see black lines on the laundry. Whirlpool Croatia denied that the gum can be the cause. After two months, they gave me new gums, but the problem still exists. After 5 months of work, the first malfunction on the washers started. The biggest problem is that it took and still takes them up to a month to repair them. And these problems I have ever since. Also, the error codes never showed the correct malfunction code. In global, if I take that I have these washers and dryer for about a year, they were out of function for more than 3 months. The warranty expired in April 2012. On these reasons, I cannot recommend any product of Whirlpool, and I have to change to another company to buy more washers and dryers.

Whirlpool water heater FG1F5040T3NOV - I noticed that when I was taking a shower, my hot water wasnt working. I went downstairs and the pilot light on my water heater wasnt on. I tried to restart it. The pilot light wouldnt work or relight. I gave up and contacted a plumber. I dont feel I should have to pay for a plumber when its a product flaw!

We have had this washer for a little over three years. We are a family of 2 so it gets only light use. The agitator stopped working and the repair was going to be $370! The repair person suggested we contact the manufacturer but they refused to even pay a portion of the repair. Goodbye Whirlpool! And yes, it left white streaks on our clothes as well.

Whirlpool refrigerator Model WRT771RWYW01 - Having been pleased with my old Whirlpool, I made the mistake of buying one now made outside the US. First, we had to have the cold cut tray replaced, which was covered in our warranty and not a problem. Then, we complained because you can only put things on the front half of the shelves or they freeze solid. We were told, This is the way they are made, dont put things in the back.” So, I have to put my eggs in sideways so the back ones dont freeze and cant use the back portion of the refrigerator shelves. I paid a lot and I am angry. Lets go back to the US people where things were made right.

Bought side by side in 2010 and after the first 3 mth the ice maker jammed up. Found out the dispenser door was not working right so it was change. But lo and behold the dame thing jammed up again within 3 weeks and the door is working. I will never buy WHIRLPOOL AGAIN. I hope they go out of Business. They are selling junk and they do not care. Made in American. Pack your bags Whirlpool. You are no longer needed.

We purchased this washer in 2017, its the top loading Cabrio washer and it has been nothing but junk since day one. Purchased from RC Wiley in Boise and unfortunately did not buy the extended warranty because we trusted that this American company would make a washer that would last longer than 3 yrs. This washer barely washes clothes, leaves a residue on them since there is no agitator, also constantly gets unbalanced or gives and error of LF which means water supply issue when there isnt one. My 15 yr old about has a heart attack when he uses the quick setting and his clothes arent done in an hour and a half. Ive even resorted to turning the thing on to just rinse and spin so things get done sooner, still the stupid washer just sits. I would sell it but I dont want to pass on the pain, so its going to the dump to or to Goodwill cause its not worth the headache. Too bad you cant trust an American company to make a good product. Sad I really wanted to like this washer.

Purchased model # WRX7355D8MOO through Lowes summer of 2013. By summer of 2014 ice started building up under freeze drawer. Little did I realize the compressor was failing, air flow was stopped up. Ice maker failed. In 2016 water dispenser calibration off, freezer failed. Called in certified Whirlpool repair. They spent three days troubleshooting problems. Repairmen told me, not to spend any more money to repair this fridge, buy a new fridge. I spent $2300 on this fridge. Its only 2 1/2 years old. Whirlpool better get their quality control issues resolved or shut down the plant. I know many part are made in Mexico, poor quality. Why pay for an expensive appliance that only last two years.

We bought this Cabrio washer WTW6400SW2 several years ago. Immediately after having it delivered and installed, it started displaying an F1 fault code. The main control board was replaced under warranty. It happened again within six months. Another board was replaced. That board lasted another six months. The warranty was up by then, so I used the machine by hovering over it and restarting it every time it failed. After two years of this piece of junk, we put it in storage while we worked on the road. It was brought out on 10/01/11. I called a repairman (who came on 10/04/11) to come replace the board again. He told me that the last two times it had been replaced with the same defective board, that Whirlpool had never fixed the problem. He claimed he had the new improved board, which he replaced for about $350. Two days ago (361 days later), it went bad again. The same repair company came back and said it was the board again. I just tried chatting with a person working on the Whirlpool website. They (of course) said they would do nothing about the washer. They do not stand behind their product, obviously. Does anyone know of a class action lawsuit over these washers? It is a ridiculous amount of money to spend for a product that does not work. This is just wrong!

The machine meets our needs and just the right capacity. It has just the right number of selection for proper washing. Very easy to load clothes and remove from the washer. There were a number of colors to select.

My dishwasher is very basic with no extra amenities, more features like an area on the rack that would wash the inside of small opening glasses and jars and I do not like the way my silverware holder just balances on the front of the bottom rack and does not attach to where it doesnt fall off every time its bumped.

I am also disappointed with this manufacturer. I recently purchased an over-the-range microwave oven model KHMS2056S. Within 45 days of use, it quit heating. I initially established a service call through Kitchenaids web site, with the first available weekend appointment approximately 2 weeks away. When the contracted service represented arrived (A&E), he asked me for a cup of water and placed it in the microwave, along with a temperature meter. After running the microwave for 45 seconds, he informed me that microwave was not heating. This was the extent of his troubleshooting, only to confirm what I had already reported in my initial service appointment description. The next step was to order parts and wait another 10-20 days for a new service appointment. When I challenged the technician on this, he stated that they were required to verify the problem and check the model/serial number of the appliance. But these were also provided through the automated service appointment system. Thanks to Lowes who allowed me to return the item, even though the purchase date was outside the 30-day window. It seemed obvious to me this warranty contractor was simply creating multiple service calls to inflate the repair costs. And ultimately the consumer pays this.

I knew I couldnt be the only one with these problems. The reviews confirmed it. I bought my Cabrio washer in 2012. Energy efficient, no agitator to catch on clothes, Great. It took me a while to figure out that the machine was eating my clothes and not cleaning them at all. Oh, they smelled fresh. That HE detergent smells nasty. The machine ate the edges off my good towels, T-shirts, jeans. Brand new underwear (thick elastic) was stretched all the way out and pulled. Normal stains and dirt do not come out even with pretreating. I started running my clothes on the delicate cycle, prewashing stains in a bucket by hand and then putting clothes in mesh bag before running the load. They still came out dirty and ruined. When I run the loads, it still registers as not being that energy efficient on the controls. Id gladly trade it back for my old washer. I feel like I have stepped back in time to a time where you washed everything in a tub or bucket. What a waste of time.

I called Whirlpool about the refrigerator that I purchased in June of this year and nothing was done about it. My situation is that the refrigerator scratches very easily. It seems that it gets scratch only by looking at it. This refrigerator is very expensive and I not even done paying for it and this appliance looks awful!! Susan the person that I was chatting with just told me that cosmetic doesnt cover and there is nothing that Whirlpool can do about. It bothers me that paying so much money for something that it is poor quality material.

I bought a Whirlpool gas range in March of 2015. Three months later the control module went out on it. It was still covered under warranty through Whirlpool, so they send a technician out to fix it. Its now a little over a year later and the control module is out again. I call Whirlpool and ask them if it was still under warranty and if they can it fix it so they say, you want me to send a technician out. Why? I just assumed since theyre sending a technician out but there were going to cover it. Well the technician gets here and its not covered under warranty. And I now I have to pay a $90 service charge fee for the guy to tell me that the control modules out on it which I already knew. Hes going to charge me more than the stove was worth to fix it so I declined to get it fixed.

Bought this model #WTW8500DC from Lowes in 2015. Ever since had problems. Stopping in the middle, not starting, recently keeps running water, lid lock issues, had multiple service calls and multiple hardware changes, paid extra for extended warranty from Whirlpool hoping that within a year all problems would be gone after so many repairs. Boys I was wrong. After spending around $1200 between this machine and the extended warranty, three year later after the warranty expired now I am stuck with this non-functional piece of junk and looking for another washing machine. Would love to hear from Whirlpool if I stumbled upon a lemon, or three year is expected life of their $1000 plus machines.

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

I have a gas range Model WFG540HOESO Airlift self clean. When anyone reaches across or leans against the range, ever so slightly, the knobs turn and gas is released. It is EXTREMELY dangerous. The Airlift self clean has never worked. When the repairman contacted the technicians at Whirlpool, they told him that there was nothing they could do. In other words, I am stuck with an oven that will not self clean. The water in the bottom does not even come to a boil.

I purchased a washer, dryer and refrigerator from Sears and it has been a terrible experience! The fridge broke twice, the dryer broke twice, and the washer broke around four times! I was told that since they fixed it last time for free, this repair was on me! If all the items didnt break numerous times, I would not be upset. But for all the items to break so many times, thats telling me that I shopped at the wrong store! The Whirlpool Cabrio sucks! So, I was told by Sears on 8/1/11 to ** it up!

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

We had Lowes install a Whirlpool model Nu40T121-403 natural gas water heater early October 2012. The temp controller went out in October of 2014. I replaced the controller myself at a cost of $30 for overnight UPS from the manufacturer, American Water Heater. The controller went out again almost exactly one year later and I again replaced it for the $30 shipping charge. In both instances the customer service person told me the malfunction was probably due to my not flushing the heater annually, causing a sediment buildup. The water to the heater not only flushed annually, but is filtered through a water softener and there was absolutely no evidence of sediment in the drain water or on the part of the control that is in the tank. Now it has stopped working a third time. I called Lowes about replacing it, but they only carry Whirlpool, so wont be buying a replacement from them.

Bought top of the line KitchenAid refrigerator $4500... Completely stopped working in 3 months. Cannot get ahold of anyone at Whirlpool & their phone system is ineffective. Appliance technician came out, cannot get the parts he needs from Whirlpool!?! He said that if he cant get parts in 21 business days then Whirlpool may consider replacing the fridge. Is this a joke?!!! I have a 1970s Frigidaire still working!

My Whirlpool refrigerator/freezer stopped cooling just after a year. I had to buy a $319 warranty. It was fixed, but broke several months later. The repairman said he would try to stop the leak and it worked for a couple more months. The refrigerator was obviously irreparable and we should have had it replaced by Whirlpool at this point. Now, that it broke again (stopped cooling and freezing) the repair service is giving us the runaround. Its over a week and they wanted us to call a repair service and they would reimburse them. The repair service and Whirlwind know about this problem, but refuse to acknowledge it and are getting away with it. With all the comments Im reading here, there should definitely be a recall. Id like to know what it takes to have one authorized.

We bought a Whirlpool oven in Costa Rica. Wanted a good oven from a reputable manufacturer. Oven has had numerous problems over the past 2 months. Local vendor is worthless and trying to run out guarantee time. Whirlpool U.S.A. says it will not help with problems for products sold outside US or Canada. Fair enough. THEN DO NOT SELL THE WHIRLPOOL BRAND WHERE YOU DO NOT SUPPORT YOUR PRODUCT.

Purchased a new Jenn-Air JCD2295KES in 2007 when we remodeled our Kitchen. Its been a decent fridge. When it quit a couple of weeks ago, I had the repairman come. He informed me that the HV circuit board was bad and sorry but they dont make them anymore. What, a 7yr. old fridge and thats it? I sort of expect things to have to be repaired or maintained but to have to throw it away because Whirlpool chose not to carry the parts any longer. I decided to scour the net and see if I could find this legendary board. Lot of places seemed to have carried it but could no longer get it from Whirlpool. I found a place that could supposedly repair them but after a few days, they called and said the microprocessor was not repairable.I contacted Whirlpool and they gave me a place that does obsolete parts and although helpful, I thought they were real opportunists and wanted to charge me considerably more for a reconditioned board that a new one would have cost if I could find one. I kept looking on the internet to no avail and when I called Whirlpool again I was getting pretty upset. Here I am with a 7-year old refrigerator and cant get parts for it, thats just not right. They were pleasant but basically their stand was sorry, theres nothing we can do. I told them that I bought a lot of appliances as I have quite a few rental properties. I cant throw an appliance away just because I cant get a part. It just doesnt make sense. I feel Whirlpool/Jenn-Air simply doesnt care. Im not interested in their excuses, I just want parts. I dont think it is unreasonable to expect to be able to obtain parts for at least a dozen years or maybe even a little more.I posed the question to them. Would you buy a $2000 refrigerator if you knew it would only run 7 years? The customer rep. said no she wouldnt. Well, Whirlpool, neither will I. I was unimpressed with their lackluster response and offer of a $300 rebate on a new fridge. I can find better deals than that on my own. I have purchased many appliance and always actually liked the Whirlpool line but Ill not buy any of them again. Shame on you Whirlpool for letting your customers down. Just because you can ignore me, doesnt mean you should. Im in business and I would go to the ends of the earth for a customer to make them happy. No wonder the Asian companies are kicking butt on the so-called American manufacturers. If your not going to get service you might as well go for the cheap price.On a final note, I did after two weeks of searching find a board hidden in a little appliance repair shop in Colorado. It should arrive here tomorrow and was priced $150 less than the reconditioned board that the gougers Whirlpool recommended. I believe it is the last board on the planet. Hopefully it will get my fridge another 7 years down the road and by then Whirlpool and its subsidiaries will have been sucked up by foreign companies and under a different label.