I just bought a Whirlpool Cabrio Washer WTW8800YC1 yesterday (1/19/14) delivered today. First load never finished, kept getting error of F51, which I looked up and its a sensor. I looked up the review on this washer and it seems to be the census that this washer is POS. Im having the store pick it up and refunding my money. My old washer is 20 years old and never had an issue with it. We just wanted a more efficient washer. Thank Goodness I didnt have the store haul it away.

This is a Whirlpool dishwasher that has been functioning for 25 years! Much better than any of my 4 newer appliances. It has never had a problem. It is easy to load and unload. The dishes are always clean. Dread getting a new one.

We got a french door Whirlpool refrigerator about 15 months ago. Model Wrf757sdem01. There were problems from day one. Serviced about 6 times by 3 different companies... Died again less than 2 weeks ago. Finally the store decided to replace it. Was under an extended warranty. We have been without a fridge for over 10 days. It has caused multiple problems for us as we are out in the country. We have to haul ice to 4 coolers... Wait on the new one (a Whirlpool). Plumber had to be called in and he has had 3 of this same model replaced! Years ago you could trust Whirlpool. Now apparently not. I hope we do not have to regret our replacement one which still is not installed! By the way the water filters have to be replaced to the tune of 100.00 a year. We are not going to use an icemaker or get water from the new one.

Do not buy Whirlpool or Maytag appliances. They do not stand by their products. We have purchased 2 washing machines in the past 8 years. Both of them quit or broke almost as fast as we got them. The customer service agents were pleasant, but they would not help us at all. The machine we purchased has a design flaw that they will not acknowledge. They have been contacted by us several times and cant fix the problem. They need to correct a design flaw that is in all their machines.All of our clothes get encircled around the agitator and the machine gets off balance. We have to untangle our clothes from the agitator and pull them apart by hand. They make bad products, including a Whirlpool refrigerator that broke within a month of us buying it. They care about selling these crappy machines. Buy a GE, Bosch or LG. You will get a machine that works properly as soon as you hook it up. We have had their representative out several times to our house and they could not repair it. The repair techs have told us that Maytag and Whirlpool clothes washers are no good.

My experience was terrible. We purchased a side by side refrigerator on June 27, 2011 and it stopped working in December, 2011. We reported this onDecember 19, 2011. A repairman was sent out a few days later, who could not solve the problem because a piece had to be ordered. The piece was ordered and the repairman came to install the part on December 28, 2011.The refrigerator is still not working at all. We have been without ice for this period of time, not to mention the inconvenience of non-refrigeration of food. I pleaded for them to pick up the refrigerator and give me even a partial refund. I was told that three repairs had to be done before they would even consider picking up the refrigerator. I am not a person who complains, but this was ridiculous. I will never purchase another Whirlpool product.

I needed a new washer and dryer, as I sold my other ones with my last house. I have been so happy with the economy of a front loading washer, and the clothes really dont require pretreating because Tide and the washer take care of everything!

We bought a WRS325FDAM02 Side by Side Whirlpool Refrigerator and from day 1 we have been having problems with rust buildup on both doors. Bought it in July 2014 and have had the service people over to figure out the problem many times. They finally decided to replace the doors which didnt help because the replacement doors are doing the same thing. We have bought everything they told us to buy to clean and try and prevent the rust from coming back but nothing helps. Our warranty was ready to expire so we bought the extended warranty only to find out that cosmetic issues are not covered under the extended warranty plan... Stay away from this model refrigerator... Not only that we were then told the doors are not really Stainless Steel just some fake crap that looks like Stainless Steel. We paid good money for this refrigerator and have to deal with cleaning rust off the doors day after day.

Water heater purchased in 2011 and is already broken. Called the hotline and they were rude. Told me I need a $199 part. I read all the reviews and it seems that Whirlpool has made a bad name for themselves with the water heaters. They were not willing to work with me.

It took several delivery attempts to get a refrigerator without cosmetic flaw and it only lasted four years before Freon leak in evaporative system occurred. It would have cost more to repair than replace. Needless to say, I replaced it with another brand.

We saw water all over my wood floor and traced it to the lower freezer unit of my 15-month old refrigerator/freezer. We had to call a repairman which traced the problem to a frozen defrost. He put in a new thermometer at the tune of $200 and now we have to deal with a wood floor problem on top of it. I purchased because Whirlpool was always known to be a quality product. I wont make that mistake again.

I purchased the Whirlpool Duet June 2011. Within two weeks, it was tearing my clothes. It didnt matter how little of a load it was, they still ripped. Five months later, my machine was leaking water. The repair man came out. I told him it was also tearing my clothes. His only response was dont load it to full. Well, I called the store where I purchased it and they are sending a repair man out again. I told them to either fix this from ripping my clothes or I was going to take a hammer to the machine and never buy a Whirlpool again or give them a good reference. I also called Whirlpool directly and told them of my problem and they acted like they had never heard of this happening before. I told them to search the internet because everyone is having the same complaint! I had a Fridgidaire front loader for 9 years and never had a problem with it eating my clothes.

I bought my new Whirlpool Duet washer and dryer in November 2011. Washer was loud from day one, but I never owned a front loader and thought that is how it was. Then someone told me that meant the bearings were bad, so I called. While still under warranty, they did replace; and I had to wait 6 weeks. Then a few months later, it started leaking. I had the extended warranty, and A & E came out and told me the bearings failed again. And now, I get a check for $750. But the machine cost more than that. Do not buy any Whirlpool, Maytag, or Kenmore. They are all made by Whirlpool.

I purchased a gas range stove about three to four years ago. I am extremely dissatisfied with this Whirlpool stove. This is the second time the electric ignitors have been replaced due to the stove not working and it is still not working right. The gas valve regulator has also been replaced because it went bad too and my oven still isnt working. I have already put around two hundred dollars in and no one has any idea why it isnt working. Apparently these stoves are a real piece of ** and everyone is having the same type of problems. Something should be done for the customers as it is now. I will never buy Whirlpool again. What a piece of garbage!

Bought a dryer (wgd9050xw) 3 years ago. We bought a more expensive one than we had originally picked out. Every year its had to have a repair of same part. First year it was under warranty which tried to bill me so I had to dispute the charge. Charge was finally dropped. We just had it fixed again for third time in 3 years. Its a fire hazard because belt wears a pulley and basically melts it and gets belt hot. I just contacted Whirlpool and awaiting response.

We bought a dishwasher, stove and refrigerator last month. Dishwasher and stove work great, however the refrigerator is junk! The freezer part works great, but the refrigerator doesnt cool at all. The first time he was here the repair man said the seal on the door was bad and he glued it. He told us to not open the door for 48 hours then everything would be fine. IT WASNT. A week and a half later he came back. He looked inside, scratched his head and told us, “This model should have the “deluxe” fan and I dont think it does!” Said he would be back in 6 days with the fan and well “see if that fixes it”.I called Whirlpool service waited on hold for an hour before getting cut off. Called back waited 35 more minutes but actually got to speak to someone. The big solution... They offered me a 6 month extended warranty!!! Ive lost an entire refrigerator full of food. Missed two days of work and am going to miss another when he brings the “deluxe” fan. Also been eating out all month and probably spent $100 buying ice. IE... MOST EXPENSIVE REFRIGERATOR EVER!!!

Love the chrome exterior and overall appearance of this side-by-side. The compartments and shelf spacing are well thought out & offer flexible adjustments. The outside components on the freezer (crushed ice, ice water, ice cubes, & light) I love, and most importantly the unit comes with a built-in replacement water filter.

The washer is a lower priced but basic machine with few bells and whistles. However this is what we wanted. Less tech with less problems so for us it works. Does the job it is required to do. Cycles do take much longer than our old machine did. Probably due to water conservation.

We bought a whirlpool water heater about two and a half years ago and started having problems with the pilot light going out. The gas company said that these have been recalled but he was wrong its the 2005 year. Sure we will have to buy a new water heater soon.

Bought a Whirlpool dishwasher and just over a year later all the wheels fell off the bottom rack. Called to get replacements and it was going to cost me over $200. I paid $800 for the whole machine. I would NOT recommend Whirlpool. I have now heard of other people having the same issue. Very disappointed. Will probably buy a new dishwasher as it will probably happen again with the replacement wheels.

I am not pleased with my self-cleaning oven. I dont even use my oven that often and I cannot get off even the simplest of stains on the sides, top, and bottom. I have tried to clean the oven three times and the stains from pie drippings are still not coming clean. It should not be this hard to clean an oven because my last oven was so much better and it was not Aqualift. The top of the oven is also very hard to keep the burners clean and looking like new. I am very disappointed in this oven and believe that this is false advertisement to the consumers. I pride myself in keeping my kitchen looking clean but this just is not working for me!

This Cabrio washing machine is really frustrating....... It goes off balance all the time. It does not matter if you have a full load or partial load, I know it has a tendency to go off balance, so I try to put the clothes in evenly. BUT it doesnt matter, it goes off balance. When the washer is downstairs, it gets to be a pain. The lid lock is a pain also. If you forget to put something in the machine, you hit pause button then you have to wait forever until it unlocks, and wait forever to unlock when it goes off balance. When it doesnt go off balance, it washes everything just fine. But if I knew what I know now about it, I would have never bought it....... I would recommend a different washer and check the reviews, which I didnt do. :(

Appliance repairman is coming tomorrow. Washer is less than 2 years old and will stop mid-cycle more than once (I re-start it)... At first when I thought the cycle was done I would get ready to move the clothes to the dryer and realize they were all soapy and sometimes they were just massively soaked so something is not working right. Sensor?? Hopefully not the computer panel as that will be too expensive to repair.

I am waiting for the third repair on my front-load washer. I purchased them a year ago and was very satisfied with the ease of use. But in April of this year, the E2F3 started flashing up after I put in a load of clothes. I called the repair line and they sent a guy to check it. Determining it was a sensor, I waited three days for the repair. Then, almost two months later, now, it did this again. He called WP and they said to replace the sensor again. I waited two days for the repair. Before he left, he started the washer to run through the cycle - no problem. I then put in a small load of clothes, and almost immediately, the washer stopped and the E2F3 was flashing again. I called for a repair, and am again waiting (without a washer) for the repairman to come back on Tuesday!!!Today is Friday. I have been four weeks almost without a washer this year. Thats also the $20 I have spent this last week to wash clothes at the laundromat, not to mention the frustration of waiting for the warranty line to pick up and the hassle of having someone here when the repairman comes. I am glad I purchased an extended warranty for this product, but Whirlpool should make their products to last!

I purchased a Whirlpool Dishwasher, model DU1010XTXB1, 13 months ago and now it wont drain nor come on. Interestingly enough, the company claims no fault and wants to charge $129 just to diagnose it. This product has never worked properly, happens to have recalls for the exact same model number, yet wont acknowledge or expand its serial # coverage despite that it is the same exact problems! Do not buy from Whirlpool!

17 month old Whirlpool duet washer door lock broke. ($300) repair! Had given my old (13 years) set to daughter when I moved. That set has never had a repair or problem! Why do they keep making things with more bells and whistles we dont need and so cheaply made? Frustrated, annoyed and becoming cynical in middle age.

Mine is a stacked unit...saves space and I just love the stooping over factor... BUT, its an energy saver and I always have to add about 5 gallons of water to it for it to cover even half a normal load...ugh!!!

Purchased on 9/12 at Home Depot. Ice maker paid for as stated in ad for home depot, did not come with fridge. Tech needed for warm food, had to repair gasket. Tech needed for cracked handle. 6 calls for freezing food in fridge compartment. No resolve. Whirlpool wanted a 2nd opinion and another tech came deeming the fridge unrepairable. Not good enough for Whirlpool. After speaking to several customer service agents, they said they do not refund or replace, only repair. I have lost hundreds of dollars of food from freezing. My fridge is reading at 31 deg. This is way below what it is supposed to read at. No call from Whirlpool since last tech came. Their customer service is terrible and cold. Whirlpool Corp. was not any help either. You can see the problem with this model if you look up Whirlpool fridge freezing food in Florida, as a woman there called ABC news and they reported it. I will also do the same.

I was going to write a negative review after our Whirlpool stove oven stopped working. We only had it for three years. Technician’s visit today was $70 for the information that we would be better off buying a new one because the motherboard is gone. However, after reading all the horror stories which are already here, I realize that we are relatively lucky - at least, our stove worked for 3 years... Still very disappointed and unhappy. No more Whirlpool products!

Good Morning. We recently built a home with Pule in Nexton, which is located in Summerville, SC. The appliances we chose came with the dishwasher, stove and microwave. Everything other than the dishwasher has been doing great, but as for the dishwasher I am extremely upset...we are newly weds and received two nice sets of glass and at least 12 of them have been broken in the dishwasher. Please advice.

Bought a Whirlpool Refrigerator Gold Series on 11/04/2014. It stop working on 6/25/2014 when I called customer service to report the problem. Received the visit of 2 serviceman on 3 different occasions and still dont know when the refrigerator will be fixed. What should I do?

In addition to my refrigerator dying after 3 years, my microwave died after 4.

I bought a top of the line Whirlpool dryer that cost me over $1,000. Havent had it for a month and it requires a service call. Have to wait two weeks for service! Totally unacceptable. The dryer is JUNK and now I am stuck with it. Horrible company. Bought from Home Depot.

Whirlpool freezerless refrigerator quit after 17 months. Bought it brand new. APPLIANCE INFORMATION. Merchandise REFRIGERATOR. Brand Name WHIRLPOOL. Model Number WRR56X18FW02. Serial Number U90502841. Highly disappointed!

We purchased a Whirlpool Cabrio Washer approximately 4 years ago thinking we were purchasing a top-of-the-line washer. The first year went great. I was very impressed with how it washed. My clothes came out cleaner than ever before; I loved it. But shortly after the warranty expired, one of the water pumps began leaking out all over the floor. We found out that a coin had passed through the barrel down into the pump and caused the plastic pump to crack with the high speed spin. We replaced that pump at a cost of over $100. We shopped around to find the part as reasonable as possible. The machine worked fine for about another 10 months, then it happened again. The new pump began spitting out water all over the floor. So again, we found another coin, another crack in the pump and again replaced it, another $100+. Finally, a third time, it was the same thing; the pump cracked due to a coin. This time, it was the pump on the opposite side, but still, water was all over the floor. This time, we ordered the part through Whirlpool and complained about this happening for a third time. My husband asked them about the Lemon Law and he was told that he would have had to purchase all of the pumps through Whirlpool. What does that have to do with it? We bought the pumps where we could afford them! The washer cost about $700 to begin with, and within 4 years, weve spent approx. $400 more? Thats not the end of it though. Now we are hearing loud noises and there is water all over the floor again every time you wash. This time, its not the pumps though. It appears that it has something to do with the bearings and maybe a seal somewhere around the barrel itself. But you can hear something knocking around - it sounds almost like a nut. We are going to call a local repairman to come and look at it tomorrow. This is just ridiculous. I feel like weve been completely duped over this purchase. The salesman talked this up like it was the cream of the crop and weve had nothing but problems. My last washing machine was a Kenmore and it lasted nearly 15 years and not once did I have to call a repairman or buy parts for it! Guess what Im going to buy again? If Whirlpool would just acknowledge these problems and fix them for people, it might renew faith in your company. I know I dont know the inner workings of a washing machine, but it seems to me that a screen prior to the pumps to keep coins from entering the pumps wouldve been a very cheap fix to a huge problem. I also own the Cabrio dryer and have hated it since the day I got it. It never dry things with one cycle. I always have to run it a second time. Knock on wood though, I have never had any breakdowns with that. I can guarantee my next buy will not be Whirlpool, nor will I pick expensive models again. I bought the cheap stuff years ago and it lasted forever! Im very nervous because I bought a Whirlpool fridge last year and I am praying I have no problems with that!

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

I purchased by first Whirlpool Cabrio washer in 2007 with an extended warranty (my husband did not want me to buy). Thank goodness I did. The machine had repeated issues to the point that the service repairman and I were on first name basis. Finally, the mother board went out. The rust on the sides was excessive and of course my expensive sheets and towels were being shredded. Lowe’s extended warranty plan did honor this and replaced my machine with a new Cabrio washer (big mistake!). The new machine; receipt for this was over $1,600.00, including the new extended warranty that ends in 2014, was bought on 3-25-09. It now requires a new drum and bearings which are being replaced today (9-19-12); however, the corrosion is just as bad and my clothes are still being shredded. Oh, also the lid no longer locks and to get the machine to actually run. I have to physically hold down the lid until the lid locks. The repairman said that there is nothing he can do as the company will not repair this or replace the machine again under warranty! The joints where the lid attaches have rusted through and that is why the lid cant lock. The whole lid needs to be replaced and the company says it would cost about the same as a new machine about $690.00. What a rip-off this company is for the consumer! I will never, ever deal with Whirlpool again and I mean never, ever again! (sans Taylor Swift)!

I am so unhappy with your product. Constantly have to restart machine. Never had a problem with my other washer. Takes forever to do laundry. Hate it.

Purchased water heater in 2005 with a lifetime warranty. We had our first problem May 30, 2013. Water would not heat above lukewarm. Called Whirlpool. Our plumber and Whirlpool determined that the temp sensor was defective. Plumber took it off and it appeared it had shorted out as the wires were black and plastic coating had slightly melted in one spot. We had replacement part in 24 hours. Licensed Plumber did repair (2 hours @ $75/hr = $150). Second problem occurred October 23, 2013. Not even 5 months later! No hot water. Hit reset button, turned temp up. No change. The diagnostic light on water heater indicated it was the same problem as before. Called Whirlpool. They sent out repair part which arrived in 24 hours. Licensed Plumber repaired (1.5 hours @ $75/hour = $112.50).I took a picture of the melted plastic caps where the wires screw into, of the housing around the wires, of the melted, charcoal crispy black of the Junction Box in the area that was directly above and covered the wires and sensor panel. It was much worse than last time. Plumber said that the part that screwed into the plastic cap had to be pried out and it broke off. You could see that this might be the spot where the problem started. We feel fortunate that we didnt have an electrical fire start from this problem. Something isnt right. Within less than 5 months, we have spent $262.50 to repair a water heater that has a lifetime warranty. Id like to give this 0 stars. Whirlpool owes us $262.50 and it might be more before this is all said and done.

My mom is 82. She purchased a Whirlpool refrigerator March 2013. Since her purchase, she has had to have numerous service calls. This was covered by her first yr. warranty. After the first yr., she purchased an extended warranty from Whirlpool. June 24th, 2014, her ice maker and freezer quit. My husband made numerous calls trying to get this fixed. He was switched back and forth from Whirlpool and Assurant. Assurant said it should be under Whirlpool and Whirlpool said Assurant. My mom felt that Whirlpool should have taken care of this problem. The refrigerator was a lemon. It was a French door style with bottom drawer freezer. We finally called the local dealer, whom she purchased it from, and he took it back. Gave her substantial credit toward another refrigerator, not Whirlpool! Very disappointed in Whirlpool... Will never purchase another appliance with this name!!!

New range and the faceplate keeps melting. Had it fixed once and it is melting again. I have been trying to contact Whirlpool but to no avail. What is my next step and is anyone else having a problem with this.

The refrigerator fits perfect in my space, keeps frozen (ice cream is creamy not a frozen block ) and cooled foods well. I love the glass shelves. I purchased 2 more bins for the refrigerator door, now I can get all my spices and condiments on the door as well as lots of other things. The freezer has racks instead of glass shelves. The top shelf is adjustable, that is nice in order to use more space. I love the ice and water on the outside of the door.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

I am extremely dissatisfied with my Whirlpool refrigerator. After less than two years, the entire cooling system has gone out basically rendering it a piece of trash. Unfortunately, Whirlpool is only going to absorb the cost of parts, so I still have to shell out $4500 to have a refrigerator repaired that is nearly new. This is not acceptable. I will never purchase a Whirlpool appliance again.

My Whirlpool Cabrio washing machine. f1 keeps showing up on washer on. Shuts off again and again.

Mind you, Whirlpool products that we have purchased in the past have been satisfactory, but gas hot water heaters, no! About four years ago we purchased a Whirlpool hot water heater that went out in a little over a year. After spending many calls and time, we found out that the HWH was on soft recall. Whirlpool credited our account, but this was to purchase another Whirlpool, which we did. We paid for installation. About 2 years later, it has gone out. Same problem. Lowes says not their problem. Whirlpool says it will pay for the part only. Plumber will cost 150-200 dollars. All the plumbers I have talked to will not repair them, then they are held responsible when it goes out! As a disabled Vet I cannot afford to throw 400-600 dollars away. And, Whirlpool tells me that if they give me an RA number to replace the HWH, it will have to be a Whirlpool from Lowes. Great! Whirlpool quarterly report looks very good. Mine doesnt look as good. What can be done about a poor working product? Or is this too big to fail? Let me know.

I had to re-arrange my kitchen and have my slider doors moved over a foot to accommodate this monstrosity. After about 2 years the icemaker and water dispenser died - had to shove a facecloth in it to keep it from making noise. The white color is very hard to keep clean. Overall, I would not recommend a Whirlpool brand refrigerator.

I bought a Whirlpool Cabrio washing and dryer in 2011. I have replaced the lid on the washer 3 times. It comes apart in the back of the lid and it will not lock in place so it will perform. I have called the manufacturer several times. They have not been of help as to why this happened. Im upset. They have no suggestions. I have owned Whirlpool appliances for years and this is the 1st time this has happened with no resolution. I just want it fix or explain why its happening.

I purchased a Whirlpool Washer/Dryer set in June 2014. Yesterday, Sept 9, the motor stopped working. The machine was on but nothing happened. Called the repairman who said the motor burned out and had to be replaced at a cost of $180 plus $75 for his labor. I paid around $400 for it a little over a year ago and now I have to pay $255 to get it repaired which is ridiculous for a ONE YEAR OLD machine. I will never buy Whirlpool again. I should have read the reviews first before buying but I always thought this was a good brand. Lesson learned, never buy Whirlpool.

Whirlpool Cabrio Washer - A total waste of money. My clothes are never clean. The low water system is rubbish. It doesnt work! Check out my pictures below. That is the result of a 63 minutes wash cycle. Dont buy this piece of crap.

A few weeks after we bought it, the washer was already having issues spinning out, and the clothes would have to go through another rinse and spin cycle. A bout a year and a half in and I had to replace the pump because it stopped draining. Even carefully loading the machine, and at least two or three times a week it would not spin out. Two weeks ago it stopped agitating actually performing washing action and spinning out all together. Last night I replaced the actuator which controls the speed or lack thereof in the spin. Still nothing. Ive reset it multiple times, still nothing. At least the clothes are getting wet. At tax return time I am replacing this piece if garbage and I will never get another whirlpool, or Maytag washer again because from what I have been told by dealers and repair men; they are all garbage.

I purchased a gas range with JDR8895 last 09/06/2007 at Home Depot in Metro Denver for approximately $1700.00. I will make my final payment on my Home Depot account next month. I was preparing dinner last September 10, 2011. I had the pans on the cooktop, one on the right rear and one on the left front burners. This was the set up because the right front burner has stopped working some time ago. Both burners were on a low setting as I was simmering pasta sauce and just warming water as I was later going to boil it for the noodles. I was in my living room when I started to smell something odd. When I approached my kitchen, there was a fire coming from the rear of the cooktop and beneath the three burner knobs. It smelled like an electrical fire. I immediately turned off the burners with my hand wrapped in a towel and started putting out the fire by hitting it with the towel and blowing. The towel caught on fire. I grabbed my fire extinguisher and was ready to spray when finally, it looked like it burned out. The smell in my home is terrible, when I tried to test the lower burner it looked like it was catching on fire underneath the knob as well, so i immediately turned it off and batted it with a towel. Im not sure what happened here. I will make my final payment on this range next month and had the previous range in here since 1977 and that still worked fine. I spent a small fortune on this Jenn-Air, only to have it catch on fire that could have potentially burned my house down.On various web sites including consumer affairs, JDR8895 has many reports of fires. If this is a known problem, why has it not been addressed as a recall? My 9-year old was making soup the day before while I was in the living room. This could of easily happened to her! It is a very dangerous situation to put your consumers in!Whirlpool Corporation contacted the appliance repair company, Columbine Appliances, to inform them that they would only be covering the cost of their visit and not the cost of the parts to be replaced in the range (the ones that caught on fire). Through Columbine Appliance, Whirlpool wanted to inform me that this is not a safety hazard and that it was my fault as I got water in the control knobs. This is not true. If I did, I was not aware and was unable to find any literature about that being a safety hazard or that it could cause a fire. I have found and have forwarded to the CPSC many instances of this exact problem, often when the range was not even in use and are happening to other consumers. I am working on combining the data, contacting the other consumers and have since refused service on the range by Columbine Appliances. Whirlpool only tried to contact me after I left them a message regarding the status of the range and that I had no interest in paying for what I viewed as a defect in their range and a safety hazard. I found a news story of this range going up in flames. Its unbelievable that this company continues to stand behind this product and blame these fires on the consumers actions. I am disabled and have an oxygen machine in my home. I have no desire to have this unit catch on fire again and potentially die, especially since water does, on occasion, end up on cooktops. Thank you for your time and attention to this matter.

When we moved into our home this past year there was a Whirlpool gas stove model number W10406473A. We have the plastic knobs on the front of the stove which need to be pushed and turned in order to turn on the gas. I recently ran into a serious problem where my cat walked across the knob area and pushed and turned the knob causing the gas to come on the stove. This is a problem due to the fact that a child could have also have easily turned on this stove. This is a definite fire hazard as well as a carbon dioxide problem. I warn anyone with this stove to replace it with another make or model immediately. Im in the beginning mode of looking to see if a recall has ever been made on this model.

I am experiencing problems with keeping my pilot lit too. I checked the screen and this is not the issue. I have just returned from Lowes where I purchased the water heater and they informed me Whirlpool supplied kits for this issue and it was widespread. They mentioned a class action and went on to tell me they and all surrounding Lowes stores are out of the free kit and arent expecting anymore. Am I to feel lucky my water heater water didnt fail sooner only to feel unlucky all of the free repair kits are now gone? Lowes provided me with the Whirlpool phone number for help and they have just informed me it will cost me $35.44 plus shipping. I now see how widespread this problem is. This isnt right. I am very disappointed in the handling of this known problem! What is my next course of action?

I love the look and performance of my Whirlpool Dishwasher. It could be a bit quieter, but overall I have no complaints. My washer was already installed in my home when I purchased it and I must say, it helps when the family gets together and you don't feel like washing the dishes. The dual chamber pod holder is great if you need to use and the heat function works wonderful. I don't have the problem of the left over water that a lot of dishwashers leave behind and no spots!

I bought a glass top stove model number W10221843A. My son dropped a plastic cup on the top of the stove. It put a hole and shattered it. Now remind you, it was plastic. I barely use this side of the stove, so not like it was weak. I paid a lot of money for this product just for a plastic cup to destroy it. Is there any recall on this stove? Any help will be appreciated. Thank you.

I am sorry to have updated that review 2 years later. Whirlpool has actually contacted me after posting on their Facebook support group. I am not sure how it happened but I was contacted by their executive team who is WAY more professional and efficient than their support team. In a matter of days my washer was replaced and installed by a new one - the closet available to the model I had - I did not pay a penny and no questions asked even though the washer was out of warranty. So my answer to you is when you are stuck do your best to talk to the executive team!

We just received our brand new Whirlpool washer and dryer from Home Depot. The delivery person started the washer and started the dryer and promptly departed. My husband immediately put a load of laundry into the washer, and he noticed there was insufficient water levels to adequately wet the clothing. Approximately 3 tablespoons of warm water were added at intervals of approximately one minute each. The water level never rose above 3 inches at the bottom of the tub despite setting the washer on the heavily soiled setting. After the spin cycles he removed the extremely damp clothing and it appeared that the machine had not properly completed the spin cycle and drained an insufficient amount of water from the clothing. He tried another load, and it appeared that the sensors were not working which regulate the water levels because most new machines use far less water. However this washer was defective. He then placed the clothes in the brand new Whirlpool dryer. The clothes ran for over five hours and never dried and the dryer never got hot. There was obviously something wrong with the thermostat. We are both disgusted and will never ever buy a Whirlpool product again. In addition because of the extremely poor response from Home Depot, we will never purchase an appliance from them again either. So sad that Made In America, which was on a sticker on the front of the machines, does it mean diddly squat these days.

They stink. Major issues with most all of these Whirlpool water heaters. I have had issues with 3 different units. I own properties and these are pure junk. Cant find parts and have to pay for shipping on warranty parts! 2 years old units junked, Ridiculous... never buy Whirlpool!

Whirlpool washers have been in family forever. RELIABLE. Extremely easy to use. Had for 10+ never had to have repairman. Large enough for queen size comforter and small enough for handful of rags. Spins like wow. Crazy dry.

DOES NOT MEET CONSUMER NEEDS AS PROMISED. I wish I read the reviews. Very expensive machine I purchased specifically for the large drum for large loads. The machine cannot handle large loads (if you consider one blanket large load). I have to unplug the machine mid wash, as the load gets stuck on one side and moves my machine across the floor. The noise in the spin cycle with even small amount of laundry sounds like a helicopter is about to land. Then last night I noticed black oil splattered all over my floor. This is a $800.00 machine. Never ever met my exceptions as the machine promised to deliver. Theres very little water that enters the drum... Not even my towels come out clean. DO NOT BUY WHIRLPOOL... EVER EVER EVER.

I bought a Whirlpool Cabrio washer about 1 1/2 years ago. It has been in the shop 2 times and is doing the same thing again of not completing a wash cycle and draining. I WILL NEVER BUY Whirlpool appliance again. If I could sue I would.

I bought at Lowes. The first one was sent back (doors stuck, suction cracked lining). Now the temps are not working in the fridge or freezer. All the food got dumped. Its sad. My old one lasted closer to 25 yrs. (and may I add up to ten children). This one has only been used by adults. I thought I could trust Whirlpool?! I sent info to local Lowes. We will see if theres any help.

I recently purchased a new Whirlpool propane water heater. Dependable name, dependable product, years of trusted service, right?! We have bought many Whirlpool products over the years but never again. Got it home and installed it. It sounded like a plane taking off, and that was in the garage. Next came the lack of hot water. Mind you, we replaced a 40-gallon tank with a 40-gallon tank and the last one we had lasted 18 years without a problem.Well, same showers as usual, and we were turning up the heat mid-shower and again and again during the shower. Even turning up the heat on the water heater didnt relieve the problem. We are not happy with the product. And, no, there is nothing mechanically wrong with it; its just sub-par. Our water heater from 18 years ago worked more efficiently than this newer model. We called customer service, and we were told that unless there was something mechanically wrong with it, such as a defect, there was nothing we could do. There’s simply no recourse.Shame on Whirlpool for not making a quality product and standing behind it. This was a very expensive purchase - over $500.00. We thought we were buying a quality appliance. Very disappointed, and I will be returning it. I’m never buying another Whirlpool product again. I can only hope that the company we bought it from has a better customer service policy. Very frustrated and disappointed.

We have a Whirlpool Gold fridge that was manufactured in 2009. MOD: GS2KVAXS01. SER: HRY0570897 and it has not been cooling properly for the last few weeks. Some days it is fine, the next day not and we have had to throw our a lot of rotting food. We got the fridge checked out and were told the Electronic Control Box for the fridge was not working. My question is, why would a Whirlpool Gold fridge that costs $1800 or so have such a large issue with 3 years? Its practically a brand new fridge and Im outraged that a large part of the fridge is not working. I understand parts break and there is warranty but its pretty bad that after the warranty expires the control box would become defective. I have been a loyal Whirlpool customer and solely buy the brand and this break upsets me very much. Especially since replacing the part will cost me $400 plus labor, we are talking about a part costing 30% of the total fridge cost! That is ridiculous. I am hoping there is something you can do to rectify this, as a fridge manufactured by what I thought was a great company should not cause such an issue and I would like to continue to buy Whirlpool products but not if this is the case.We have called Whirlpool customer service many times to be ignored, berated, told I cannot speak to a supervisor and nothing will be done. Never in my entire life have I ever known a company so horrible to exist. I have had bad service before but this takes the cake. Plus, no company that I have ever dealt with would ignore you and not provide any discount or remedy. I cant believe this is a big brand with the way they carry on. You would assume they would be some one person owned company who doesn’t have a penny to spare. I don’t respect this company at all and expect a resolution because they are truly insulting in all the channels.

I have a gas range Model WFG540HOESO Airlift self clean. When anyone reaches across or leans against the range, ever so slightly, the knobs turn and gas is released. It is EXTREMELY dangerous. The Airlift self clean has never worked. When the repairman contacted the technicians at Whirlpool, they told him that there was nothing they could do. In other words, I am stuck with an oven that will not self clean. The water in the bottom does not even come to a boil.

We purchased the Cabrio Agi top loading washing machine in 2011 (3 years ago). After 2 years it started leaking from the plastic drum (Bearings?). Luckily we have it in the basement on concrete floor, so there was no damage, just frustration. This was poor purchase on our part. We should have searched for more reviews. The wash time is ridiculous; it is too long, an average of 50 minutes per load. I dont know about how clean the clothes were, I guess they were OK. I didnt notice a smell, or them looking dingy. The Cabrio is a piece of junk if the bearings went out after 2 years?? We just purchased a heavy duty Speed Queen, top loading, agitator washer. My wife loves this, its like the old Maytag we had. They told us they wont be selling these washers after next year. Buy them while you can. The Cabrio is headed to scrap yard.

All JUNK!! Replaced all new within the last two years. The washer I replaced was twenty + years and was still working fine was just upgrading, big mistake! Washer is sounding like it is going to walk out the door. Replaced dishwasher after twenty years and the new one was leaking within one year and recently got replaced. The new one did not last one year and also is leaking. Now washing dishes by hand. Lastly replaced hot water heater and that is junk too. Has six year warranty after one year pilot light wont stay lit, Whirlpool said would replace the gas control valve for free but I need to pay to install. I WILL NOT PURCHASE ANYMORE PRODUCTS FROM LOWES OR WHIRLPOOL AGAIN!!! HOW CAN A RETAIL COMPANY REPRESENT SO MUCH JUNK?

Whirlpool Washing Machine Model WTW4950XW0 - This washing machine was purchased as a gift by my father. We have owned this machine for about 2 years. I am very disappointed with the quality of this machine. I have 3 children and several pets. I use my machine a lot and need a quality item that will last. This machine is not that item. Within a few months, the machine was off balance and bolts had to be tightened. We have had problems with the belt, bolts coming loose and the machine not draining.More recently, the machine has become very loud... For approximately the last 6 months. My husband has taken the machine apart and looked for anything to be wrong with it and has found nothing. Now the machine is not running. I will turn it on and it fills with water and then stops. I will clear it out and restart it and it does the same thing. Another issue has been with spinning and draining. The clothes are soaking wet even after the drain/spin cycle.I have researched what could possibly be wrong with this machine and have found a vast number of items that could need replaced. With the money I have already put into fixing this machine in the past and the amount it will cost to fix it this time, I believe I will be further ahead if I buy a new machine made by a different company. I will not be buying a Whirlpool product again.

Purchased our stainless steel Whirlpool Gold range hood microwave oven in January 2011. By August, there were problems. It was noisy. It would occasionally shut off for no apparent reason and eventually in August of that same year, it completely stopped heating. The magnetron was replaced at no charge because it was still under warranty. The microwave has continued to run very loudly, vibrate a lot and is still prone to random shutoffs. Now a little over 2 years later, it has now stopped heating again...I am assuming another bad magnetron. How is that possible? Our last microwave lasted for over 10 years! In fact we got rid of it when it was still working fine so we could get this one for over the range instead of on our countertop. So now I have a Whirlpool paper weight for which I originally paid $485. When I called Whirlpool, I was informed a service call would be $130.00 PLUS any necessary parts and labor costs OR I could purchase the repair plus 1-yr extended warranty for $289.95. Upon requesting to speak to a supervisor, I was informed that there were no flags in the system indicating any problems with this line of microwaves. I further inquired on how they are aware of problems... Essentially a phone call warrants little proof of any problem. A service tech would have to actually go out and witness that there is a problem for it to be noted. So, for those of us that simply decide to turn our back on the product and buy a new microwave, it would go undocumented by their company. My top-of-the-line microwave is less than 3 years old and has broken down again. Doesnt common sense tell you that there is a problem with the quality? I know Whirlpool has been around for 100+ years and I really want to like them, but if they dont support the consumers that purchased their products, I can no longer do the same for them.

I purchased the model WDF530PAYM0 serial: F14106104 dishwasher. The foremost reason I purchased this was it had nylon racks. I have discovered that the racks are rusting! It is rusting on the ends where nothing can touch it. I am very disappointed that it is advertised having nylon racks and now it is rusting and deteriorating. This dishwasher states racks-nylon, not racks-nylon coated. I just took some pictures of the racks. I decided to look underneath the top rack where the upper spray arm is located. Now I am plain sick! Most of the underneath is rusting. This dishwasher was purchased and installed 2 years ago. I paid $600 and you would assume that something mechanical would quit after years of use on an average of 1 to 2 times per weeks. Not this one...rusting racks and hard telling what damage the rust flaking off during running is causing to the mechanical components. Lesson learned: Their definition of nylon and nylon coated has no difference.....I very much disagree!

Six months after purchasing my Whirlpool Washer model number WTW5000DW0 I would hear what sounded like rocks in the bottom of spin drum during spin cycles. Then noticed it was taking longer for clothes to wash and sometimes the water did not completely drain. Called for Service under LOWES warranty (the worst people to deal with). Tech comes removes a penny and dime and tells me that is the problem. Leaves. 45 minutes after he leaves there is the noise again. Call and set up for this Service Company to come back. Even though they went out of business prior to the appointment Lowes Service would not listen to me and insisted I stay home ALL DAY for someone who did not show up. Repeated calls to the Service Company resulted in nothing - phone disconnected.So finally after much frustration I am given new appointment with new Service Company - PARRISH. Tech comes in here five minutes and wants to know the sound, I explain. He checks out the unit and tells me it is a major problem and the part and labor will be costly. Best if they just replace the machine. His added comment - I see a lot of this. So if this machine is such a problem why was it not recalled? I am getting a replacement as I have warranty and machine was not a year old when problem started. Lowes Service Contract is another problem but I will deal with that later.

I am a single parent. So I was very excited when I had saved enough to purchase a new washer and dryer. I purchased Whirlpool because I had been told that was a good brand. From the beginning, I was having issues with the washer (Whirlpool Front Loader model #WFW8300SW04). It wouldnt start or it would not spin, or it would just lock and not be able to get it open. I had purchased a warranty. So I called to have it serviced. The tech came and told me that I needed to have my floor leveled under the washer. I hired someone to concrete under my washer and dryer. Again the washer still did the same thing. I used the warranty again. The second tech told me that I needed to have my electrical outlet changed. I again hired someone to change the outlet. Yet still the machine didnt work. I then hired a tech to come out and was told the mother board needed to be replaced. Had that done. The machine worked for a short time with no issues. But yet again it wont start, or wont spin, or it locks and you cant get it opened. I contacted Whirlpool and their answer to the problem was they would be glad to set up an appointment to send out one of their techs (at my expense). I have hired another tech and being told that the mother board once again needs to be replaced. I am so disappointed with Whirlpool and their service. I dont understand why they won’t stand behind their products. I will (when able) purchase another washer, but it most definitely will NOT be Whirlpool. Anyone else having issues with the same model? Would like to hear.

Purchased Whirlpool clothes washer Cabrio Platinum about one year ago. Never sufficient water to clean items. Appears that there is no way to add additional water to ensure that items are cleaned. Many items come out dry and still soiled.

I purchased a Whirpool fridge five years ago. To date it has had 7 repairs. The latest round has lasted over five weeks and the expensive warranty I also bought is about to run out. The repair man is on his third repair and I havent had refrigeration for five weeks. In the meantime they wont replace the fridge, and it takes two weeks between scheduled visits by the authorized repair man.

My wife and I purchased a Whirlpool Duet washer and dryer 5 years 1 month ago. We purchased the front load style because they were supposed to be better made than the older style. Its just my wife and I no kids. We never overload the washer or dryer. Now the drum bearings in the washer have gone out. I feel that a washer should last longer than 5 years and 1 month. I dont think I will be buying another Whirlpool.

This is about my Whirlpool washing machine that has abruptly stopped working. My Whirlpool washing machine was bought in 2013 and was running [absolutely] great until Tuesday October 3, 2017. I called customer service and they said it was out of warranty. My Whirlpool washing machine model number is: WTW48008Q0. Serial number is: C34923747. I do not have the money to get this machine fixed. I am already a struggling mom, working hard to pay bills and I am already falling behind on most of them. I just had death in my family and now the machine dies - well there seems to be no end to all of this. I would really appreciate Whirlpools help in getting my machine up and running again. I have been a loyal Whirlpool customer over the span of more than two decades. I am a Whirlpool fan. My past machines have lasted 12 plus years on upwards to 15 years each.Let me share exactly what my washing machine is doing: I went to wash clothes as usual the other day; the machine filled up and stopped abruptly - that was it! It did not spin but instead emptied the water without washing the clothes and made some loud chitty chitty bang bang noises before it was all over. I unplugged it after wasting a lot more water thinking that it might just suddenly start working. It did not start working again, it just continued its non-working status.My family has bought Whirlpool washing machines and dryers for years from Sears; we were totally satisfied with the products we purchased, however, this washing machine did not make the five year mark. I really do not know what is going on with the machine; what I do know is this - it stopped working and I would like to get it working again. Hopefully it is not defective by design. #WhirlpoolWasherDefectiveByDesign. I found Whirlpool washing machines to be very reliable and would love to continue my great relationship with Whirlpool.

I had problems with the door closure on day 3 of my French Door Refrigerator Model # WRF560SEY. The flap on the left door that seals them fails to fold back if I open the right door first. Which didnt seem like a big deal until I tried to close them and have to remember to close the left door first or itll bang against the right door and Im afraid itll break that piece off then the refrigerator is worthless. The manufacturer drop shipped a new piece, after several attempts of adjusting the closure, and it still does not work. I have written Whirlpool and am told they have a new door on order but it will take 6-8 weeks, that was in March. Now when I contact Whirlpool no one ever returns my calls or emails. I have had the refrigerator only for 15 months and I have fought with either the store or Whirlpool since the third day of owning it. No one cares as long as the appliance is paid for. I will never buy another Whirlpool appliance.

We purchased a Whirlpool Cabrio washer and dryer less than 2 years ago. These are supposed to be high efficiency appliances, but the washer has never cleaned the clothes well and the dryer often has to be run more than once in order to get the clothes dry. Then, about two weeks ago, the washer started making such a loud noise on the spin cycle that it sounded like a jet plane taking off. It was hard to hear the television when it was running. Today, it started screeching and water leaked on the floor. I called the number listed on my manual and was basically told that it would cost half of what we had paid for the machine to fix it. What efficiency, a poor machine that lasts less than two years. We will never buy Whirlpool appliances again.

I got a Whirpool Cabrio Washer that I purchased in 2008. I am constantly getting ul code. If washer is leveled, it leaks water out the bottom rear of the washer. Its a piece of junk. I called Whirpool to no avail. Whirpool will not stand behind their product. They know they have a problem but wont do anything about it.

I purchased a total of four Whirlpool appliances in June of 2008. Almost thirteen months after the installation of all four appliances, I experienced a problem with the control panel on the Gas Range GW397LXUB, and a sensor control problem with the Microwave GH5184XPB5. Fortunately, Whirlpool agreed to repair the appliances at no charge because it was so close to the end of the warranty. The microwave was an easy fix and simply had to be unplugged, reset and plugged back in. However, the entire electronic control panel had to be replaced on the gas range. Several of the buttons simply stopped working and I was only able to bake at 350 degrees. Again, almost thirteen months after the installation of the new control panel, it happened again. Same buttons stopped working. When I contacted Whirlpool, they refused to replace the part because I was no longer under warranty. Whirlpool refused to admit that there was a problem with the control panel, so I guess it was a crazy coincidence that I experienced the exact same problem on both. I filed an official complaint with Whirlpool in hopes that if enough people do so, they will issue a recall. I am now experiencing a problem with my refrigerator ED5FHAXSB03. The fan vibrates so loudly that you can hear it throughout the entire house.

Chris from Whirlpool contacted me the same day that I filed my complaint. He offered to replace our water heater at no charge. We will pick up our new water heater this weekend and install it. Hopefully, it is designed better than our current water heater.

I bought this Whirlpool America dishwasher because it was cheap. Even though Im Canadian, I like patriotism and I could get behind the American flag logo on the washer. Let me just say, if you like when food comes off your plates, and attaches to your cups, then this is the dishwasher for you. It is always a surprise when you open the door to discover which dishes have been cleaned, and which dishes have inherited the food particles from the now clean dishes. This appliance really helps you work on time management as you are required to wash all your dishes before you put them into the dishwasher. 0/10 would not recommend for anyone who wants clean dishes.

Looked for the best refrig we could find and it turned out to be a piece of junk! Less than 3 years old, paid 2700$, french doors bottom door freezer. It started making a lot of noise it seem to be coming from freezer. Called Whirlpool, they said to clean coils. We wanted a repair company to come out. They set an appointment for next Tuesday between 12pm and 5pm. Said ok.Was making so much noise, and no longer freezing everything so call said company. Lady was very rude, and said they would not be out on Tuesday but sometime the following week. This would not work for us so called another repair shop, said they would be out. They were here before 6pm. Found out that they have been having this problem, had same type of call already this week. Repair for this problem would be over $1100.00. No thank you! Would just as soon junk this appliance. So very sorry we wasted our money on this.

Standard looking dishwasher. Quiet and efficient. Best value for the money. Highly recommend. Chose this brand over more expensive options and made a great decision!!! I dont have a single complaint.

We purchased a gas range (Whirlpool AccuBake model # mfgxfg361lvt1 serial ry1810956) a few years ago and have been very unhappy with the gray grids that it came with. We wrote to you about how we should clean them and you recommended heavy-duty degreaser, pin31552a and gas grate & grill cleaner, pin3167a, which we purchased. Neither worked, even with heavy elbow grease. We are very upset. We have purchased Whirlpool products all of our life and would like an answer or some type of explanation. If possible, can we get the grids in black? We try our best to keep these things clean and this is a very bad patten.

My KitchenAid side by side refrigerator/freezer is a beautiful thing, shiny steel surface, gleaming white inside. However, its made poorly. The ice cube maker compartment broke and the replacement came without any installation instructions. It was hard to figure out and I broke it. Now, everything in the refrigerator is freezing and changing the temperature on the digital panel makes no difference. McKinneys appliance, where I bought it, no longer has a refrigeration technician and they referred me to Whirlpools 1-800 number where I supplied some information and sat in my chair on hold listening to music for a half hour before hanging up.The recording on the phone suggested their online chat where I was asked the same sorts of questions and was told I would get the answers I wanted by paying $5.00. I had no idea what I was getting into but I didnt pay, just terminated that inquiry. Feeling cheated by the company whose product I had mistakenly purchased. Im now running the risk of a technician visit, sometime between 8 am and 4 pm a couple of days from now. I have to be prepared to wait around all day for somebody to look at my refrigerator, charge me a lot of money and, from what Ive read online, potentially see the problem return in a very short space of time.

When our home burned down, had to get a manufactured home. Orig. refrigerator size was 32 cu.ft. This one that came w/ the house is a lot smaller. Weve has issues with ice dispenser several times in the 18 months weve been here. But I would recommend this size.

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

Whirlpool works great. I need another large shelf space between 2 shelves. The refrigerator has a small one but the large one I prefer.

My Cabrio was built in April 2016, its now Feb 2019, and its not working. Shows error code of LF, the inlet water value is bad. I bought a Sears protection plan, repairman comes out, tells me no-one has the part anywhere, its backordered and no way to know when it will deliver. Sounds like a scam so Sears doesnt have to fix it and Whirlpool makes little to none of the part so you have to buy a new machine. This machine also takes forever to wash clothes, sometimes part of the clothes come out dry because not enough water. Its a huge tub, but of no use because theres not enough water to clean properly therefore, you have to do small loads. I always put it on high water because the other features like, quick wash & normal do not give but only little streams of water! The first one I had delivered made a funny noise from day one so Sears replaced it the next day. This one has NOT even lasted 3 yrs. There needs to be new legislation placed upon these companies with regards to the products they make. It should be illegal to make such junk and be able to charge high dollar for it and it doesnt operate well or last very long. They are laughing all the way to the bank on everyones dollar, intentionally making products that last less than a few years! I Will NOT purchase Whirlpool or any of their products again! They owe me a new Cabrio and Im going to make sure I get it and get my moneys worth! DONT WASTE YOUR HARD EARNED MONEY ON THIS JUNKER! DONT BE FOOLED BY ITS PRETTY SLEEK LOOK.

The tub mounts of my 6 years old Whirlpool washer are broken. It’s too expensive to replace. Seems like built in obsolescence! Ive also had mold/odor issues. Finally, I know how to fix that, now this. I just want to warn others, these machines are not designed for the long haul.

We replaced older GE with the giant front load model that can do king size sheets and comforters. It has worked like a champ. It was a bit more but worth it for us. In a year and a half no issues no problems and I like the control lock feature so I dont keep hitting it off when I go thru the laundry room to the garage.

Freezer side went out on model# ed5kvexvl00. Fridge is less than 2 yr old. Didnt expect anything to go wrong so quick. The extended warranty, I did not purchase. Replaced relay switch - no changes in problem... Contact them (Whirlpool) and like every else, got nowhere with them. 3 weeks and no fridge... Hopefully the compressor is not bad. Will find out soon. I will be researching before I select new appliances in the future. They need to be ashamed of themselves.

I bought a whirlpool W 10632082A a yr ago. I read the reviews and thought it was a good product. I was wrong. It has never washed the dishes good. It has terrible screens that always get clogged. The dishes never get dry. I think the dishes would get cleaner throwing them in the yard and spraying them off with a hose. I would not recommend this product at all.

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

It is a double oven. Temp varies too much. The oven is very inconsistent. Cooking Thanksgiving the temperature would not stay even. It took much longer than intended. It was quite frustrating. I would not recommend the Whirlpool double oven.

I replaced my 12 year old Whirlpool double ovens with the current Whirlpool double ovens. The new 30 built in double ovens have been re-designed to vent the heat below the lower oven. The ovens come with a part that pushes the heat down instead of straight out. My built in ovens have a cabinet drawer below and after using the ovens just 4 times over the holidays I noticed the heat is damaging the finish. According to Whirlpools service center I should have checked on that before buying/installing. They told me to stop using my ovens, that this is a fire hazard, but they are not responsible. They do not have a solution to this problem. This is a poor design on their part. There is a disclaimer in their installation booklet that came packed with the ovens that the installer gave me. It says the cabinets need to be able to withstand the heat of the ovens. The cabinets can handle the heat of the ovens, just not the hot air venting directly onto the cabinets below the oven. Where does one find cabinets that can withstand 400 degree heat being pushed directly onto them? As a customer I did not have that information until after the ovens were installed and it was too late to purchase another brand.

I purchased it new in July 2008 for $550, a single homeowner average 4-5 loads a week. First time it broke down, it was just inside the one-year limited warranty. It broke down again Sept. 2011, the basket separated from spinning mechanism. I learned that after $75+ missing day of work, repair tech quoted cost of repair $885 and a minimum of 10 days waiting for part to arrive.I called Whirlpool, the guy on the phone was nice but told me I was out of luck. Even if I had purchased the 3-year warranty, I would still be out of luck. The washer was manufactured in April 2008. What a piece of junk. Save your money and skip it. I wish I had. Aside: Whirlpool, whatever happened to standing behind your products? I used to think you were a quality brand. Im extremely disappointed and wont be purchasing any of your products in the future.

Three days ago my washer Whirlpool Caballero has made a loud jet noise sound while spinning. While researching for a repair Ive noticed many complaints about this type of washer. Is there any resources that will help me get this repaired?

Whirlpool 29 cu ft French Door Refrigerator WRF989SDAM - We purchased this refrigerator September 2013 for our new home. We moved in November 18, 2013. The refrigerator made a very loud buzzing/humming noise from the beginning and did not make enough ice. The shop we bought it from came on 2 occasions to work on the ice maker and finally totally replaced it. Then the rack on the bottom of the left door fell out and contained glass jars of pickled vegetables. They broke and made a big mess and etched our travertine tile floor. We called the shop and they sent their son out who put the rack in with duct tape which of course did not work so we took it out and put it in the cabinet. We had to pay to have the tile polished to remove the etching. On the weekend of November 15, 2014 the humming noise was so loud that we called the repair person again and they came out on November 17, 2014. At first they thought it was a fan motor but the freezer started making a loud noise and the owner came and said the compressor was going out. Our food was beginning to thaw and we asked if they could at least loan us a refrigerator to use. They brought us an old small fridge which was put in the garage. We took all our food out there. They came November 25 and picked up the fridge to be repaired. We had been told the warranty was out but after calling your company they were told Whirlpool would cover parts and labor. Today is Thanksgiving Day and we can not cook a big meal due to the small fridge and freezer and we are buying bags of ice every day. We have family visiting and must go out for dinner. We have no idea of when our refrigerator will be returned to us. This has been an expensive and disappointing experience. I would never recommend your refrigerator to anyone due to this experience. I really feel we should have been offered a new refrigerator at a discount. We bought all our appliances from Dons Appliances in Okeechobee, FL 34974 and they are all Whirlpool. This refrigerator cost $2299 and our total order was $9,642.84. We would appreciate a response from your company.