I just bought a brand new Sterling steel refrigerator not even 2 months ago, and since I got it, noticed rusty spots coming out,and now has spread all over. I called customer care, and they said it wasnt cover under the guarantee,and to buy a special spray out of my pocket expensive to remove the rust. I am Very disappointed with the service I received, for its not even 2 months old refrigerator and it looks like it is old now. In addition, the company didnt offer to send someone to take a look, checking and make sure theres no future problems with my new purchase, and as a courtesy removing the rust free of charge.

Cabrio Washer WTW660SW2 - For 2 years I have been getting f1. When I talked to Whirlpool they said they were not aware of this problem. Now I have to pay to fix it. Looked online thousands are having the same problem.

I bought a Whirlpool Duet washer and dryer. The washer is model W9740. Less than a year later, the spin cycle sounds like a jet engine ready for takeoff. I got the extended warranty. A & E service tech showed up. The rear bearing and both halves of the tubs need to be replaced. The cost is $1423.33 to repair. It’s more than the cost of the set. I’m still waiting to see if the warranty covers it. I emailed Whirlpool to let them know I was **. I had a chat with someone named Laura. She disconnected from me after I told her to tell Whirlpool CEO they suck! Never again will I buy a Whirlpool product and I hope they go broke!

I had the bearing go bad in the tub after a few years of service. It cost hundreds of dollars. As an engineer, I look at this and it is a design made to fail. The seal design is inferior compared to old washers that had a shaft seal made to be on a spinning shaft. This is a rubber lip seal that is going to wear because it is using washer as a very bad lubricant! When the seal goes bad, and it will, the water runs down to the bearings and destroys them, and you have the replace the whole tub as a $300 part!

I purchased a Whirlpool Cabrio washer (WTW6500WW1) on 9/11/09 for approximately $800. Now three years later, it needs a new rotor and stator costing $470 in parts and labor. I called Whirlpool and was told I could get no help with the cost of parts because of the age of the machine! A simple Google search of the F51 error code that I am getting will show you that these machines are $800 pieces of junk! I am not repairing this machine. I am going to run it until it dies and simply buy a new washer. You can bet your sweet self it will not be a Whirlpool! I can only hope to inform enough buyers about this to keep them from the same fate.

Do not waste your valuable dollars on this refrigerator. Not even 5 years old and have had nothing but issues with this fridge. The ice maker quit a few months ago, started leaking water from somewhere behind the wall panels and now the freezer door is frozen shut and the refrigerator section is warmer than the outside air. Did I mention that this refrigerator isnt even 5 years old yet? A piece of junk is a piece of junk and this fridge is a piece of junk!!!

Ive always had good luck with Whirlpool. They last longer & dont have as many repairs. Ive had to have a lot of repairs with Maytag washers. The dryers didnt give any trouble. I recommend Whirlpool.

Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both ice makers went out, The computer on the filtration will go off. Refrigerator had problems maintaining temperature since 8.12.17. The refrigerator no longer works. This is my second unit since 11.09.16. It came from nfm.com.

This washer started out to be good. Its only 5 yrs old. We began to smell an odor. Went to Lowes, spoke with someone in appliance dept. Purchased something for washer. DID NOT WORK. We have tried bleach everything. Our clothes smell. I have skin rashes and I think it is related to mold and mildew. Called the service center. They said could be a sock stuck around the tub area. They need to recall this washer. We spent a lot of money and it has ruined everything. Cannot get the odor out. We cannot afford another one. There is black mold around the rubber lining when you open up the door.

My 15 year old front loader quit working and was going to cost more to repair than we thought was worth it. So, we went shopping at Home Depot and based on discussions with salespeople ended up with the Whirlpool cabrio toploader. What a mistake. I am so disgusted with this washer I dont even know where to start. If there was any way we could return it we would do so. The clothes come out wrinkled, twisted, absolutely covered in pet hair and detergent and fabric softener residue. Yes, Im using HE detergent, in the correct amounts. Yes, Ive read the manual front to back. Yes, Ive tried all the troubleshooting suggestions. No, they dont make a damn bit of difference.I would give anything to have my old front loader back. It was a great little machine that did a wonderful job of cleaning our laundry. Pet hair was washed off, I could lay things out to dry and they werent all wrinkly and did not require ironing. Just about everything that comes out of this cabrio machine that I lay to dry needs to be ironed before it can be worn. It is just a horrible, horrible machine and Whirlpool should be ashamed of themselves for foisting this off on unsuspecting consumers.

We have tried to have our refrigerator fixed 3 times. Same problem every time ice build up in the freezer. Clearly after reading all the reviews Whirlpool has made a very poor quality of a product and they dont care. Hopefully others will read these reviews and learn that its not worth it to buy a Whirlpool.

I bought an adapter that I added to the kitchen pipe, drilled a few holes in my cabinets to route the hose and voila! It is small but big enough so it's perfect for me. I didn't realize it had an internal heater so I was moving the hose between hot & cold under the sink but now that I know. I will try the heater. The settings are complicated so you have to read the instructions fully. Before I read them I thought every load took 2-3 hours but they don't. I do like to use the heavy soil setting and that does take a couple hours, but if I'm in a hurry or the load is not that bad I use a shorter 50 min setting. For the drain hose I either put it out the window or put a screen in the sink & tie it to the faucet. You have to tie it down wherever you aim it because the water comes out with enough force to throw the hose. I had a couple incidents of kitchen flood before this stuck in my head, now that sucker is secured well. I intend to make a permanent drain to the pipe eventually but for now I just use window/ sink. This required a longer drain hose. For apartment use, I am very happy.

My Whirlpool side-by-side refrigerator is just 4 years old. When they delivered it, they noticed damage on the bottom which required them to bring me a new refrigerator. The new one had issues with the ice maker that required multiple service calls to fix. The refrigerator door always seemed a bit misaligned as it was a bit lower than the freezer door, but it closed, so I never complained. I was just tired of all the issues! During the last six months, the door started to remain ajar instead of closing completely so that we had to always be sure to apply sufficient pressure to close it tightly. I considered calling in a repair, but it was still closing so I thought I might be overly critical. As it got worse, I realized the door was defective, but one day, it just fell off completely without warning as though the hinges were made of butter!After multiple service calls, a tech reattached the door, but I could see that it would not hold and sure enough, it is starting to remain ajar again. I have contacted the warranty company who is now saying the service tech claimed we were hanging on the door. This repair company the warranty company uses has an F rating with the BBB. Now, Im being told it may take a couple weeks to get another repair company to give them an opinion, but the issue is clear, the door was defective and it looks like they found a way to avoid having to make good on the warranty!

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

We purchased a Whirlpool refrigerator in 2010, model #ED2KHAXVB01, side by side with ice maker. Fortunately, we purchased a 5-year service contract at the same time because the ice maker has broken twice. Unfortunately, I have had to replace the shelves while still under warranty quite a few times. The sides of these glass shelves are made of poor quality plastic and crack constantly. The drawers are the same way. The refrigerator is no longer under the warranty and Whirlpool wants $109 per shelf. I told them I would pay for replacement shelves only if they could send shelves that were made with better quality materials. Otherwise, I might be spending $1000 per year replacing shelves. The Whirlpool representative told me there is nothing that they can do. I see many people with this problem posting complaints on the internet. Do not buy a Whirlpool refrigerator. I have been married for 37 years and never had to replace one shelf in any refrigerator and still have a 40-year old refrigerator in my basement with no broken shelves!

Our Whirlpool refrigerator breaks down after two weeks of purchase. I purchased a Whirlpool fridge for my son and his wife as a house and new baby gift. Just two weeks later, the fridge was not cooling and seemed to not be working. The technician was called, and he confirmed that the fridge was not working. We called the shop where the fridge was purchased from and advised they would not refund or replace the fridge.We are now forced to wait for a replacement part that could take up to 2 months to arrive. And there is no guarantee this problem will not reoccur with a new part, as per the technician. I called Whirlpool and lodged a complaint, but that went on deaf and ignorant ears. I am told to call the service repairer. I am sure there is a law to protect Australian consumers.I paid nearly $1,000 for a fridge that is useless! I would like Whirlpool to contact me, and tell me why they shouldnt be accountable for their product. I would like to return the faulty fridge, accept a refund and buy another fridge. My family are living out of an Esky, and this is a ridiculous way to refrigerate food stuff for adults and children in the heat of northern Australia. Whirlpool, I am waiting for your call.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

I purchased the original Whirlpool water heater from Lowes in April 2008 for $372, and an installation charge of $443, grand total - $815. In February 2012 the tank leaked profusely, enough to ruin a section of hardwood floor in the room behind the garage where it was installed. Whirlpool provided me with return authorization, and Lowes provided me with a replacement water heater. So far so good. Since the original installation was done through Lowes, the replacement had to be as well, according to Whirlpool, but now they charged $500 with tax to install the replacement water heater! Grand total now is $1315. Fast forward to May, 2014 and the replacement water heater, just barely 2 years old, shuts off with a code of Bad gas control valve/thermostat. I call Whirlpool and an extremely rude 20-something staffer tells me the unit is out of warranty by one month! The replacement unit has no warranty at all - nada - only the original one does... Is this unbelievable or what?! BUT, they would be glad to send me the replacement of the defective part for $200 PLUS overnight shipping charges, and I would be responsible for all labor charges to install it. Had I opted for this my original $372 water heater would have wound up costing me in the neighborhood of $1800!! I told her in no uncertain terms what she could do with the repair part, and now I am going to go shopping for a water heater that will last me more than 2-4 years, and you can bet it wont be a Whirlpool, and it wont come from Lowes.

After owning the highly recommended Cabrio for only 2 years, I was told it would cost $300 for the motherboard!! I have always used Whirlpool but this machine is terrible. Water saving is not an option when washing clothes. Unless I use the bulky cycle, my clothes come out dry and smell dirty.

Whirlpool Washing machine Model WTW4800XQ1 - This machine ran fine for the first 6 months, even though my old machine took 40 minutes for a large load and this one takes an hour. Then, I had to call the repairman out and he said it was the fill valve. He didnt have one on the truck and said he should get it in within 3-5 days. Well a month later, I had to call Lowes again to find out what the problem was. They had him back out with the part within 2 days. Then, I had to call again. This time the repairman ran a test and found a bad spin motor, he had the part on truck. Third time to call and the machine is back to not spinning out properly. My old machine lasted over 14 years. Whats wrong with these new ones?

My first time with Whirlpool (Always had GE) but at the suggestion of our builder, we went with Whirlpool and the stainless steel is horrendous. Nothing will clean it or make it look STAINLESS. My refrigerator, dishwasher, double oven, tall vent all look terrible no matter what I use! I have never had this problem before. Im embarrassed to have anyone go into my kitchen...

Washer doesnt get soap out of clothes. Had tutorial from service man. Must use extra rinse every time and still have soap on dark clothes. Worst washer I have ever owned. Makes washing a lot of extra work and frustration. Have tried everything to no avail. Takes at least three times longer to wash clothes with all the steps I have to take to get soap out. I understand EPA demands for less water usage, but clothes still must be properly cleaned.

I had purchased fully automatic top loaded WHIRLPOOL WM 360 BW PRO-HS 9.5 on 08/05/2019. I had purchased the above machine after going through the various claims made on the website. However, I regret to say that since installation I find that the performance of the machine is not up to my satisfaction. Even after two visits by the engineer, the following issues remain:(i) The machine makes lot of noise in the initial stage.(ii) Though the timer shows a particular time during selection of a washing cycle, in reality the machine takes one and half times more than the timing shown. In case one selects warm / hot water, the actual time taken is twice that shown or more. I am sure in winters it will take more time in case warm / hot water is selected.(iii) The clothes get badly entangled during wash.In the past I had a LG front loading washing machine which never gave me any problem. I had gone for the best top loading model of Whirlpool hoping for better performance but it has only caused problems. Not worth the expenditure.

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

I purchased the Whirlpool Gold series cook top range-stainless steel. It is of good quality and looks very nice. It is also easy to clean and for the price it has a self cleaning oven. I didnt think that I would like this range but over a period of time I truly love cooking on it.

Most dissatisfying experience with Whirlpool. In 2013 I bought a stackable Whirlpool washer and dryer. Everything worked well for two months, and then the washer started having problems. The washer memory board unit (MBU) needed to be replaced. This was done under warranty. One and half years later I started getting the error F07 which means an electrical problem. I called Whirlpool and they told me a technician would cost $85 for a service call. I delayed the call until today.The technician came, did a diagnostic and then advised me that I would need a new MBU. The cost plus labour amounts to almost the cost of a brand new washer. To add insult to injury, Whirlpool advised the service call would cost $89. (They upped the price since my last call.) You can imagine my shock when the technician told me that the $89 covers the first 15 minutes. I paid $133.34 for one half hour diagnostic testing and to be told I need a new MBU which is on back order for at least 6 months!!! My recommendation is - NEVER BUY any Whirlpool product ever.

I purchased a Whirlpool dishwasher on March 13, 2007, along with a 3-year extended warranty. Well on Nov. 15, 2011, I had a part in the control panel go out, so they replaced it and they charged me $129.00 for labor and $29.18 for the part. My dishwasher is doing the same thing. It doesnt finish the cycle and I have to restart it, so I called the repairman A&E. They said the part is only guaranteed for 90 days. The part only lasted six months! Its the same part and the same problem. It should be considered a defective part. No matter how many you have replaced the part, it is going to need to be replaced and at $160.00, I cant afford it. They should have to pay for defective parts. Also on this model GU2600XTPSI on the panel buttons, the start button was made with this puffy plastic that has pulled apart and now it looks terrible! None of the other buttons were made this way. What a crappy workmanship, they should be embarrassed. This dishwasher was not cheap; it cost $650.00 plus $50.00 for the warranty. 4 years is too short of a time to have to replace any home appliance. There are appliance out there that are three times as old as mine and they are still working. I guess in the last 10 to 15 years, big companies dont care about their products or the people who buy them, just about their profits! I will never buy or recommend Whirlpool products.

Its a very good one, it kept my stuff cold, and fresh when my other fridge went on the Fritz, but only one problem, and that is, it has glass shelves and if you have kids, it’s hard to keep clean!

We purchased a Whirlpool refrigerator because of the brand in August of 2011. Its December 2012, the entire door needs to be replaced. It appears the cost will be as much as the original $750 investment! We called Whirlpool expecting they would stand behind their brand after hardly 18 months, but no ... It is clearly a defective door to begin with.

I bought my refrigerator model WRS49/WR151 from Courts our local appliance store in November. The side panels of the fridges gets extremely hot which make me think it can set on fire at anytime. When I contacted the store two days after purchase they made it seem as though it is something normal. I never had a refrigerator that got extremely hot that I can scramble some eggs on it. Thats why I cant even rate my experience.

I have a model ED20PK. The doors are rusting on the outside.This refrigerator was purchased by my husband who has passed, I do not have the receipt and I dont know where he purchased it. The refrigerator worked perfect. It has been in my kitchen from day of purchase. My home is adequately heated in winter and air conditioned in the summer. I have an up-scale home. I dont see any reason to replace the refrigerator, but I cannot stand the deteriorating condition of the doors.If I replace it, I will not buy a Whirlpool or any brand made by Whirlpool.The rust is not just a discoloration, it is actually rough to the touch and is getting worse day by day. If you have any answers or help I would appreciate a phone call. I am not really in an economic position to just go and buy a new refrigerator.

Same problem a lot of people have written about in your forum. Purchased a double door stainless steel refrigerator, bottom freezer, # GX2SHBXVY from Sears Canada on 12/17/2011. Warranty expired December 2012. Now we have ice forming on the floor under the bottom freezer though water hasnt seeped out as we are now cleaning it daily. Sears wants to charge $75 per hour + parts as there is no extended warranty. Whirlpool says its a common problem with most other Competitor models too. REALLY, ITS NOT. Have checked with a lot of friends of mine with similar models. Nobody is having a problem with especially units hardly one and a half years old. My bro-in-law also bought a Whirlpool a year prior to mine. He is having no problems. See no reason to spend $300-$400 on a comparatively new unit. Also have a 7-month-old stainless steel Whirlpool dishwasher and 4-year-old Gold Accura cooking range. Now spend morning and nights looking at them wondering when they are gonna blow. Need to replace my washer/dryer too but guess which brand I am not opting for.

This machine always leaves me questioning if its going to finish the cycle. It goes thru all kinds of spastic sounds in order to advance to the next step. I learned I cannot presoak a load more than 10 minutes before the machine empties ON ITS OWN! I just dont trust the machine and would not buy again.

We have been having white plastic pieces shoot out with our ice the past two days. We have only had this fridge for about 15 months. After reading these reviews; I am assuming when I call the service will be terrible as well as any fees for them to fix it. I sure hope it is under warranty; or I will never purchase Whirlpool products again.

I thought with the big tub I would be able to wash my king size bedding and other large things. Theres barely enough water to wash a small regular wash. Since it has no water it does not clean my clothes. Why the big tub if you cant use but one fourth of it?

Last week dishwasher leaked. Set up repair with our local gas company that has service plus. Came today. Repairman showed me there is a hole in the bottom of the tub. Upon closer inspection it looks like the manufacturer drilled a hole that wasnt needed so they routed out a depression in the tub and must have put in some sort of plug or filler of some kind which now came out. I called Whirlpool and explained to lady about the defective tub. She said well if it had a plug of some sort put into the tub it would have fallen out before this. I said Well it didnt it just must have happened as it never leaked before. She said it is no longer in warranty. I told her this is a defect to me as if you drill a hole in the tub that wasnt necessary and then the plug failed that you put in to hide the extra hole. It is a defect not a warranty issue. Upshot is she wouldnt do anything about it. I told her I have always bought Whirlpool but if this is their policy its the last time I buy anything made by Whirlpool. After reading all the complaints registered here about Whirlpool I guess I am more than fortunate as my dishwasher (bought in 2006) had run great until their plug fell out (Great except for all the rinse aid that has leaked out for several years.).

High end Whirlpool dual front loader washing machine model number WFW94HEXW2 died after 5+ years of less than moderate use. Used no more than once a week. Paid for a top end model. Had 2 mechanics look at it. Mechanically it is fine. The CCU is not working correctly and wont allow it to start. We replaced it, but to no avail. It is barely out of warranty at 5+ years old. Called Whirlpool and they said they would do nothing. Asked for a manager and she was rude to add insult to injury. Cant get to the serial number because the door is locked shut as part of the shutdown problem. Cant find original receipt so including a picture of the credit card purchase. Trying to contact retailer but so far have not heard back from them.

I bought a Whirlpool french door refrigerator, model # ED5LVAXWS about five years ago. I didnt have any problems until last month, on August 25, 2016. The ice dispenser stopped working, and the refrigerator went off. I had to throw out a lot of food. I got a new extended warranty that day, and a serviceman came out the following day, 8/26. It turned out he wasnt a repairman, just someone to diagnosis the problem and order the parts. The part was ordered, and the fridge would be repaired within 5 days, but the part was delayed because of a Hurricane Hermine, which completely understandable.On 9/8 the repairman arrived, but he realized that the original guy who diagnosed the problem was in error. He had ordered a compressor, and what needed to be replaced was the thermostat. As of today, 9/29, the part is still not in -- I was told its on backorder with no ETA. If I didnt have a mini fridge, Id be at a complete loss. I called what I thought was Whirlpool to complain about the part taking so long to arrive, but was told they can do nothing. It turns out that a company called AIG U.S. Warranty Division handles Whirlpools guarantees. I am not a happy camper.

Defective Product: I had to replace the fan motor on my refrigerator, which is barely 3 years old. I contacted the company and they told me it was out of warranty. I asked the repair person if he see this problem a lot and he said no. I have had other Whirlpool products which lasted for decades.

Purchased a Side By Side refrigerator just 16 months back and this is the Third time the ice maker has failed. Who makes JUNK like this?? Is there not One company that can make anything to last at least three years. I am disgusted with the junk we bought that has Whirlpool on it. I should Sue Home Depot and Whirlpool for Fraud.

We bought our stainless and black Whirlpool stove last month. We love that its black topped, and doesnt show dirt. We love how the oven door seals, and the fast heat. What we do NOT love, is how easily the knobs turn. You barely brush against them, and gas leaking into the kitchen. I called for service. Our guy said yes, they turn easier than most of the stoves he has worked on. He called tech support from my kitchen, and I overheard the guy at the other end. His response was dismissive. I have had gas ovens for 20 years. They have without exception, had a spring type feeling to the knob. This stove has none. I am writing this so that if others are experiencing the same thing, they will see it is not their imagination. Something is wrong with the design of the knobs or some part is missing.

My Whirlpool super capacity 465 started flaking out on the temperature and burned our dinner. I had a repairman over to repair which he did after about 3 hours of testing. Less than 6 months later it did the same thing. Overheating in the oven.

It was about 6 years after purchase that the ice maker completely quit making ice. To change the filter you have to get down on your hands and knees to do so. If youre elderly, this can cause a problem. Overall, it was a good refrigerator.

This dishwasher is poorly constructed. I cannot use it now, as the top racks assemblies have both fallen apart and the rack will not hang. The bottom rack is functioning on 1 wheel assembly out of four. And the one that is functioning is a new one I put on it three weeks ago. The dishwasher is 2 years old. I am very disappointed in Whirlpool, and I will certainly not purchase another one when I buy a new dishwasher.

I bought a Whirlpool washer WTW4800XQ top loader. I have owned it for about two years and now it has tore up, the repair bill will cost almost what I paid for the washer. I feel it is bad business to sale something and it not last any longer than it has. No one should have to buy a washer every two years!!!! When it gets to the spin cycle it works fine and then all of a sudden it will beat and bang and if you dont get it stopped it will be in the middle of the floor. Im very upset and put out with Whirlpool!!!!

MODELGR673LXOQ WHIRLPOOL RANGE - I purchased this range in January 2014. It is a good-looking range with a ceramic top and a convection oven. It has burned more food in a year than I had burned in several years. The top burners get red hot no matter where you have them set. They turn on very hot, then turn off and after a while they are red hot again. Cooking anything that requires a medium or less heat burns to the pan bottom. The oven works alright as a regular oven but when put on convection it burns the food closest to the fan before the rest is cooked. The company sent a technician to check the stove. He checked the temperature of the oven and said it was running too hot. He changed that setting and the first time I tried to bake it took forever. I reset the oven back to where it had been. The tech made no attempt to check the top burners as he said they couldnt all be bad. I hate this stove I had my former stove for thirty years and never had problems with it.

Whirlpool Cabrio Washer - After 15 months, washer bearing have gone out due to tub seal leaking. Repairs are $450 but repairman doesnt want to touch it due to he know it will go out again. Whirlpool said Im sorry. Lowes said these are coming off the shelves soon but there are still some for sale. DONT BUY!!!

Whirlpool over stove microwave/convection oven model GH7208XRY-4 - I purchased this top of the line unit in April 2012 for a vacation home kitchen remodel. It wasnt installed until June 2012 and stopped working in May, 2013 just after the warranty period expired. The problem was with the touch screen panel that went blank and the fan/light control switches also failed. This unit has only had light use since my wife and I are retired and use it primarily for heating tea/coffee. I contacted Whirlpool customer service and they graciously offered to cover the cost of replacement parts but I had to pay a service charge of $125. The factory technician said the whole door needed to be replaced since the electronics were not readily accessible so it took about a week to get the replacement door which turned out to be the wrong one and needed to be reordered. The technician finally replaced the door and the faulty fan/light switch. Within a month the fan/light switch failed again but was still under warranty so it was replaced for free. A little more than a year after the last service the touch screen control panel began operating by itself changing screens and beeping randomly. This was somewhat disconcerting but the unit continued to work pretty normally until my wife placed a small plate of leftovers in oven to be reheated for 1 minute. She walked away to do other things and forgot about the food in the oven until we noticed a strong burning odor and found that the microwave was still running some 20 minutes later and had turned the food into a black mass of burned food and the plastic cover was melted and burned.I contacted Whirlpool service thinking that the unit was under warranty from the previous service but they said the parts only carried a 90 day warranty and my only recourse was to pay for another service call and purchase another door panel for approximately $400 or I could buy an extended service contract for $300. Needless to say Im not about to spend that kind of money to, at best, get another year of service from this inferior product. This is simply not a safe product that could have started a deadly fire if I had not been present to stop it when I did. I have probably owned a dozen microwaves from other manufacturers and have never had any kind of problem including a comparable GE unit that has been flawless for over 15 years. I am extremely disappointed that Whirlpool has cheapened its product line to such an extent but I suppose I shouldnt be surprised since I noted this product was made in China.

I bought a Whirlpool washer and drying matching set (model 6400sw3). I liked it because it was extra large without agitator in the middle. Ive had it for about 2-3 years and I have already replaced the drain pump, motor and barrens, it has cost me over 500.00. I thought now OK its working fine, but now its giving me a code every time I wash of LD. I am so fed up with this!! I should have bought a new washer but I felt as much as I put into it, I basically built a new one. And now this code comes up every time and I have to power it off. Im not sure if anyone else has had this problem but I just dont know what else could go wrong with this. I will never ever buy a piece of junk like this again!!

First, let me say we are so lucky and blessed to get home in time to prevent my home from burning. My Whirlpool range, model 4rf364pxk0, apparently decided to turn itself on (no one home) and grew hotter and hotter. It obviously burned out the thermostat because it was way hotter than cleaning mode. The key pad was melted and sagging inward the control panel warped, heat pouring from it. The racks and interior were glowing orange! My back splash tile blackened and cracked! The oven door locked! Oven hood ruined although it probably saved my cabinets! We hit the breaker! There was so much heat you could feel it on the outside of the exterior wall of the house 30 minutes later! The clean up to my kitchen has been horrible. Black soot and strange greasy film on everything and the stench has been toxic enough to give my husband a raw throat and myself a migraine! Oh and here is the ironic part - my husband was bringing me home from a hospital stay from high blood pressure! It would be almost comic if it wasnt so darn scary! Please, please address this issue before a more tragic story is posted! From looking at this site, it is obvious that there have been other incidence of your stoves turning themselves on and uncontrolled heat. I firmly believe another few minutes and our home would have been engulfed in flames. Now I will spend my weekend shopping for a new ceramic range, hood and tile!

I bought a Whirlpool top loading washing machine with dryer on top, model # WGT4027EWo, last August, not even 3 months old and noticed the lint was not coming off the clothes. We tried cleaning out the washing machine with vinegar, wiping down the sides, using smaller loads and even used the gentle cycle. Nothing helped. We have had 2 different repair men out and they said there is nothing wrong with the washing machine and to put the clothes in the dryer and use fabric softener. I have never had to use fabric softener in my washing machine to get my clothes clean. When reaching out to customer service, I have spent over 2 hours and no satisfaction. They state that the technicians say there is nothing wrong with the machine. I was told by both of the technicians that they removed the lint trap from this machine, but no one is taking responsibility. My whites have blue lint and my darks have white lint, so too strong an agitation, as suggested by one repairmen is completely wrong! What to do when you spend over $1,000 on a washer/dryer combo and they dont work correctly and Whirlpool doesnt stand behind their product? Honestly, I will never buy another product from this company, and I 60 y/o and never made a complaint before about a appliance in my life!!! I dont even think I can give them 1 star! DO NOT BUY WHIRLPOOL - CUSTOMER SERVICE IS HORRIBLE!!!

Less than 1 year ago, I bought a washer and dryer. From the beginning, we have had a water problem and the water only comes cold... no warm water in the normal cycle. They came 6 times to service the machine and they cannot fix it. They said there is nothing is wrong with the machine but it does not wash with warm water in the normal wash cycle. I advise not to buy this product anymore. It is under a warranty so they should fix it or replace it. I am sick and tired of talking to them. They said if we send the service guy then I have to pay for it which is not acceptable because it is under a warranty. If anyone is thinking about buying this product, I advise not to get it and waste money on it.

Two water heaters three yrs old that went kaput. Thankfully, they are under warranty. However, the tech that I called out said that his company doesnt work on Whirlpool because they are junky and they try to blame the tech if something doesnt work. I called to get new part, and of course now, I get to pay for labor. The lady on the phone actually suggested that I hire an electrician and replace a breaker instead of receiving parts for Whirlpool. Unbelievable. Needless to say, I echo all of the same concerns as the other posts. Im done with Whirlpool.

My Whirlpool is reliable, however it does not have a soaking cycle which I would enjoy having. It also has an unbalancing problem when speeding if I attempt to wash heavy loads on the extra large load cycle. However, it responds very well on large loads for heavy washing. Shortly after I got it the timing had to be replaced, but no problems since then. Overall pound for pound for the dollar it is a good machine.

After having the ice maker replaced on our 14-month old Whirlpool refrigerator, things seemed to be working fine for a while. However, now there are puddles appearing on the floor in front of the refrigerator. This is a freezer-on-the-bottom model and the ice maker is at the top so I was fairly certain it has nothing to do with the ice maker. Turns out there is something dripping into the back of the freezer and over time it builds up a giant ice sheet on the bottom of the freezer compartment. When the ice sheet gets large enough, the dripping water flows out onto the floor. Now Im going in every couple of weeks and chipping the big ice sheet off the bottom so it will stop leaking for several weeks. When I see puddles in front of our refrigerator I know its time to go chip the ice sheet out again. Seriously, I dont think Ive ever had a brand new, and expensive, appliance perform so badly. Whirlpool... never again.

The unit hasnt given me any trouble over the two (2) years we have used it. The bottom freezer works well and was a concern when buying, but has worked out well and convenient, but you must keep the refrigerant coils clean.

I bought this washer thinking it would last me for a long time. And now it wont wring out my clothes and I just wanted to say I am disappointed in my Cabrio Washer.

I have enjoyed my stove for 16 yrs, it is very reliable and easy to use. The heating elements work well and heats up quickly. During this time I have not had any repair done. The areas of improvement that needs to be implemented is the inter glass that is installed at the front looking into the oven. In order to clean you have to take the front door off which is very difficult to put back together.

Whirlpool Cabrio Washer and Dryer - The washer does not stay balanced even with a very small load (even though advertised can wash King size comforter). Even with a light load, we have to put the dryer on Heavy Duty or Bulky...and usually have to dry a second time. When attempted to contact Whirlpool, no help available. WORST PRODUCT I HAVE EVER PURCHASED... Would not even want to GIVE this set to a friend or family member. DO NOT PURCHASE THIS PRODUCT.

Purchased a Whirlpool French Door Refrig. Model #WRF 954CIHZ200 in 11/21/2017 from Best Buy for $2300.00 on sale. Within the 1st year the Ice Maker broke & repairman said the ill design caused the wire to break. He had replaced numerous ones for the same reason. In the 2nd yr the freezer started frosting. Next thing the freezer quit. Next day refrig quit working. Called Whirlpool, said, So sorry. We will send you a $50.00 Visa gift card. That was to cover $200.00 of just bought groceries. Called repair guy & he diagnoses compressor was bad. (IN A LESS THAN 2 YR OLD REFRIG. THAT COST $2300.00????)Now, we are 28 day w/o refrig. Living with a Igloo cooler. Whirlpool says they have no stock left on compressors for our refrig. (probably because there are so many going bad in their refrigerators). They are trying to locate one somewhere in US so that takes 6 days then they have to ship to repair center then they have to schedule us for repair which will probably be another 7 days. Ghee, what a mess! Dont do it folks! Buy a LG or Samsung! If I had it to do again, thats what I would do! Whirlpool is Not what they use to be when I trusted them. Years ago. P.S. I bought microwave, stove, & dishwasher! They are all unsatisfactory! Never again!???

We purchased KitchenAid Model YKESS907SS05 Electric Range from Appliance Canada April 2012, just before we took possession of our new home. We began using the range in July of that year and it worked well until September 11, 2014. At that time we decided to use one of the features of the range which is the self-clean feature. During which the control panel failed and our oven ceased to work.We contacted Appliance Canada and they suggested a technician come to assess. We called the suggested number and they send a technician that was not Whirlpool certified and we had to pay out of pocket for the visit $158. He did absolutely nothing during the visit. We then called Whirlpool Canada and they informed us that he was not Whirlpool certified and to call Appliance Canada, we immediately called Appliance Canada and made arrangements to have certified technician come to assess. Whirlpool Canada also indicated at that time that the board that failed was still under warranty and we should not have to pay. September 22nd the second technician came to assess the situation, used tape to cover the front blowing air duct so as not to have the hot air blow back onto the control panel. This was a temporary fix, they ordered a control panel in the interim that they would then use to replace. The control panel came in October the 22nd, was replaced and the new board was faulty, put old one back in and re-ordered another board. The part was on back-order. By mid November, after numerous calls, we called Whirlpool directly. They authorized that the technician to get the part from another supply source. On November the 26th, technician came back - tried new board could not get it to work, left it with us and ordered additional parts. At that time the technician who was taking the case had a family emergency and would not be able to come back out until the new year. Subsequently, Appliance Canada authorized a new company to resume our work with a new technician (Toronto Appliance). He came out December the 17th, with the board that was left behind, he was able to get the oven working. December the 22nd while in the middle of cooking a meal, the oven failed again. We called Appliance Canada and they had a Technician scheduled to come December the 24th from Toronto Appliance. However, on December the 23rd the oven resumed working. The Technician came on the 24th but because the oven was working again could do nothing. On December the 31st, while dinner was in for guests, the oven failed yet again. We called Appliance Canada, yet again, and they scheduled another visit with a new control panel and additional board. The technician arrived again today, January the 28th, and could not get the stove working. He was instructed to order an additional part and we are to wait another 2 weeks. In total, we have been waiting for 4 and a half months, we have also been told that we were not to have used the self-clean as this causes these types of problems. Why is it offered, in addition, Whirlpool has not supported our direct calls, nor authorized the replacement of a product, that for all intents and purposes, is faulty. We have had no success in the resolution of this issue nor support to reach a resolution from all parties involved. I would suggest not buying any product from those involved as their lack of support for their product is appalling.

Whirlpool Cabrio drain problem - I never had a washing machine that lets so much through to the drain pump. I replaced pump three times already. First of all, if you put anything with buttons in this machine, you can kiss it goodbye. This machine destroys clothes then lets buttons and coins and whatever through to destroy the fins on the discharge pump. When is the BBB going to do something about this consumer ripoff?

Purchased a Whirlpool water heater (model ND50T122-403) through Lowe’s in Dec 2013. Later discovered online it fraught with breakdown issues. 11 months later ours broke down. Whirlpool Customer Service first told us We dont have any authorized plumbers in your area. Went to Lowe’s the next day - they called on their hotline and we got a call back from Whirlpool that afternoon. Told us part would ship out immediately (arrived next day - no complaints there) and gave us an authorization for 2 plumbers. Both are over 35 miles away and one is out of state. Called once the part arrived... First one said hed try to get to us in the next 4-7 days; second one said We get to warranty work as fill-in work. Well put you on a list and call if were going to be in your area. While we did a bit of web research before buying this water heater, we really should have taken the model number, gone home and googled it before buying. Wish wed gone with a unit from a real plumbing supply place. They were a lot more expensive but you get what you pay for.

I got a new Whirlpool washing machine and dryer last year and Im very happy with both. I like the fact that it offers a quick cycle if you have a small load or need something quickly. If youre debating on what brand of washing machine you should buy I highly recommend Whirlpool or the other brands because Ive had really good luck with mine.

We purchased this water heater (Whirlpool 50 gallon, 9-year warranty, Regular Electric Water Heater, Model Number ES50R92-45D) in July 2015 when Lowes had a special financing offer. Doing other remodeling in the house, we didnt have it installed until the beginning of November. A local licensed plumber installed this for us and we havent had a hot shower since. We have called Whirlpool at least five times. Theyve had us replace the elements, replace the electronic thermostat AND the regular thermostat, then they even had us call a warranty plumber they use to inspect the tank and authorize what needs to be done next. When he arrived, he said he hadnt ever even SEEN this model before. Being fed-up with cold showers, I called Lowes to see if we could just take the thing back to the store, but they said that since it was after the 90 days, I would have to get an authorization number from Whirlpool. I just spent another 20 minutes on the phone with Whirlpool explaining my situation and they said that they cant authorize the return of a tank that can be repaired. I then asked if we didnt have a money back guarantee and the guy said, Unfortunately NO. He then suggested I call the plumber they had recommended to come out and look at it again. The guy was from Tampa and when he was here, he just wanted to get home since it was nearly 5 PM AND hes the one who said he had never seen this model before. What would be the point of calling him AGAIN??? When I buy a BRAND NEW product still in the box from a reputable store, I do NOT expect to have to troubleshoot and fix it. IT SHOULD WORK. Well, I have learned another valuable lesson from the school of hard knocks (and cold showers)...Always read the comments on a product before purchasing.

I installed my new water heater in 2012. Within 3 months, it was not producing hot water. When I called, a helpful person at the Whirlpool warranty line told me it was because there was too much cold water being mixed into the hot water coming from the tank. I hung up... Called again and was told that they would be able to get someone in 2 weeks out to my house to check it. I told them that was not acceptable. I hung up... I called Lowes, where I bought it. The person on the other line finally, after more than 1 hour, was able to get a repair person out there within 2 days. I had to pay the fee to have the guy come look at my hot water tank, and tell me that he hated Whirlpools. He called Whirlpool, 3 times; he was hung up on 2 times. He explained what had happened was I had a hot water leak, that it probably it was overloaded, the thermostat control everything else was fine. However, that I had installed the heater myself not a professional. Therefore it was not up to NATIONAL code; therefore, Whirlpool refused to honor the warranty. So, short version, in order to get the tank repaired, I was supposed to spend an additional $300-$400 to bring the heater up to code for them to honor the warranty. What you ask made my heater out of code? It is outside in my utility room, and the flue was cut to fit and the OUTSIDE vent pipe was not above the roofline. It didnt matter that it is not in an enclosed space, that this was nothing to do with the reasoning the thermocouple went out.I simply turned up the heat, so far so good. Will I ever buy another Whirlpool? No. I have a Whirlpool fridge bought before the hot water tank situation. The ice maker went out within 6 months of purchase. When I called to have it repaired, the service guy stated he hates Whirlpool. The piece he had to replace was plastic that was replaced with a metal piece that should have been metal to begin with.

I bought a top of the line Whirlpool front load washing machine (WFW97HEDW0) and drier with my new construction house. After a few months the washing machine began making a loud, banging noise during the spin cycle. Then about a month before the 1 year was up the unit broke and dumped all the water in the drum into the catch pan it was installed on. I called for service and someone showed up in about 3 days. The tech opened the unit and found that the plastic/composite drum the spin unit was contained in split in half all the way around. The tech exclaimed he had never come across this issue and would report in what he found but that he did not have the part and it would most likely be a whole new unit but that its up to whirlpool to make the call. I would find out that whirlpool had decided that the unit can be fixed and they have ordered the part and would call to schedule the repair.A week went by, with no word. I called warranty service company, Via Services, and they tell me that the part is on back order and that it would be two more weeks before it would come in. Now were looking at being without a washing machine for a month. I communicate this to the builder and they somehow get whirlpool to come out a week earlier than they said they could. The day came for the repair and two techs take nearly 8 hours to repair the unit (how is this efficient?).After the repair the unit ran with an odd noise that I attributed to the way it was stacked. A month goes by and two days after the 30 day repair warranty I go to do a load of laundry and the unit turns on but wont run. I called for warranty work because it was clearly not repaired sufficiently. I schedule a tech visit which is for a week after. The day come and the tech says he cant fix the unit without charging me for the repair because it is now out of warranty and if I have the extended warranty then I need to set that up with the extended warranty group. I send him away because I had just paid for the extended warranty. I called whirlpool for the extended warranty work and they schedule a repair contractor to come out in 3 days.The repair contractor calls me directly to confirm if the unit is side by side or stacked. I let them know that the units are stacked and they say they cant repair it because its a two tech job and they dont have enough techs. They send me back to talk to whirlpool. Whirlpool then notifies me that because its stacked I have to either unstack it myself or hire someone to unstack it for me. Well, I cant unstack the unit by myself and why should I have to pay someone to unstack it when thats what the unit was designed for? At this point I am going back and forth with the builder to get a refund so I can replace the unit. I will forever steer clear of any whirlpool or subsidiary products. The products are flimsy and the service is no better.

Just like hundreds (maybe thousands?) of others who have had the same part failure causing the refrigerator to leak, I had it and was told by my very honest, highly reputable repairman (not the one KA recommended!) that it was a DEFECT. I bought a French Door style #4609730. First, I complained on Twitter and the Social Media folks gave me the runaround. I kept it up and then, filed a complain with the Better Biz Bureau. They sent the complaint to Whirlpool, who owns KA. They gave me the runaround too - UNTIL I TOLD THEM HOW MY LOCAL TV NEWS station was interested in my story (true, I went to them too). CORPORATIONS SHOULD NOT GET AWAY WITH DIRTY BIZ TACTICS!

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

We have a Whirlpool washer wtw5640xw2, we have been experiencing burning wire smells for some time. We had bought the extended warranty. Lowes sent out a repair company. They replaced the main board and the problem has continued. This has been as intermittent problem with the burning smell. We experienced it this week really bad! I thought the machine was on fire. We called the repair company and they said they had fixed the problem. My husband called the Whirpool number and they said they would NOT do anything to help us. We are trying to get help from Lowes where we bought the washer. I am terribly afraid to use the machine. This model needs to be discontinued.. We bought this machine 5-07-12. If we dont get some help, we are going to our lawyer.

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

I have owned my Cabrios for over a year. They have given me no problems at all! I keep them cleaned with Affresh, even though Ive never ever had a smell in them. Also, I have never ever had my washer or dryer not do its job!! My clothes are fresh as a daisy and clean. I bought my Cabrios because my father purchased his first set and raved about them. So, I used his to try them out. Absolutely wonderful machines!! You get more area without those crappy agitators in the way for one thing. Always fresh water, not washing in the same filthy water, yuck! It wasnt but maybe 4 months later for our new house that we got our Cabrios. I insisted on them! LOVE LOVE LOVE my Cabrios!!!

Whirlpool Cabrio washer - Absolute piece of garbage! Doesnt clean clothes at all. Too bad there isnt a glass top to this machine where you can witness the inefficient operations as it goes through a cycle. How can a machine be energy efficient when a cycle takes an hour and a half? What a sad situation that this is made in America. I feel like such a sucker when I read all of these posts.

I am very disappointed with my purchase of the Whirlpool Refrigerator Model # WRF535SMB. As soon as the warranty ran out, it began having problems with ice build up in the bottom of the freezer. I see this is a common complaint and wish I had read the reviews earlier. The appliance is only 3 1/2 years old. Other complaints - impossible to clean the freezer. Mold build up on the seals. Glass plate shattered in a thousand pieces when I very gently set it on the counter.French doors, white, freezer at the bottom.

We bought a Cabrio washer & dryer September 2010 for a room addition that wasnt completed yet. We didnt get moved in until the first of November. So the washer wasnt used until then. In January 2011 (15 months later) it stopped spinning so clothes were dripping wet. We called Whirlpool and were told that they would be happy to set us up for a service agreement for $322 for one year. We declined since we bought the washer for a little over $500. When we had a local Whirlpool service man come out and he determined that it was the control board which would cost $265 (Whirlpool only warrants parts 90 days). I sent an email to Whirlpool and was told too bad, so sad. We called their customer care line (that is really not the term for that phone center) and asked to talk to a supervisor, who essentially told me the same thing. Whirlpool is making equipment that is extremely poor quality. There is no incentive for them to produce a better quality product as they make money on the extended warranties that are necessary, or if you dont buy an extended warranty they charge an extraordinary huge price for their parts, which they dont warranty. We will never purchase anything made by Whirlpool. I am not sure where this useless piece of junk that I have will end up but I intend to let everyone I know what a terrible company Whirlpool is to deal with.

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

Most of my appliances are Whirlpool - dishwasher, refrigerator, clothed dryer and the Cabrio washer. The washer before this one, I had it for over 10 years and replaced it because of rust (thats another problem with Whirlpool - rust). Now the Cabrio hasnt got all kinds of problems - UL, F1 and jumping. The serviceman asked me for $450 for repair; it included a set of springs for the drum, a new electronic board and a 30-day warranty on parts and labor. Im better off buying a new one (I cant afford at this moment). My wife is scared of the darn thing and refuse to use it so now I have the job of washing and standing guard to make sure the washer doesnt leave the garage. Thank you, Whirlpool - and my refrigerator works fine all rusted.

I’ve found many years of flawless performance from many Whirlpool Appliances! Once they are 20+ yrs old, I tolerate their aging and repair issues if they occur. My current microwave oven is 10 years old and was removed for a kitchen remodel, replaced after remodel and hasn’t skipped a beat!

We bought the dishwasher as part of our major kitchen remodel. After 1 year, 10 months of successful operation, the wash motor failed. We are now faced with paying about 1/3 of the cost of a new unit, after less than 2 years. I dont expect new appliances to last forever, but less than 2 years is ridiculous. I would definitely not recommend this product to anyone.

I purchased a Whirlpool stove, microwave and fridge in November 2012. The fridge model #WRT771RWYB01 has been a lemon from day 1. I have had the repairman out for the same issues multiple times. Ice build up in the freezer, water tube to the ice maker frozen, food in the fridge freezing, blah, blah. They have taped, glued, replaced everything they can and to no avail. It still happens. When you call for service, it takes 2 weeks or better to get someone out. I will NEVER buy another Whirlpool product! This has truly been a nightmare experience!

Dont buy. Purchased over the range microwave. Service order less than a week after install. Heats unevenly. Burns center of bacon consistently without fully cooking ends. Popcorn pops half the kernels yet Whirlpool says nothing wrong with product. Well within 1 year warranty but had to pay for service call cause Whirlpool determined microwave was operating as manufactured. Laughable! This company does not stand behind their product or their customers. Never again will I purchase a Whirlpool product.

After 7 calls to Whirlpool and 3 service calls, we still have white detergent stains on all our clothes. Today Whirlpool told us we needed to put one item at a time into the machine. Not only that, but pants needed to be loaded waist band up and gently placed; Shirts, collars up; socks toes down, etc. etc. Are these folks at Whirlpool serious?? So today, we called them back - still streaks. The folks at Whirlpool want us to take and send them pictures of our clothes. This is ridiculous.

Tried to do a small 2x3 bathroom rug and the spin was thrown off kilter. I have been doing laundry a long time and I know how to evenly distribute clothes etc so the washer should be able to handle it for the price I paid. The high end front loading Whirlpool set.

The Whirlpool duet front loading washing machine came with our new house five years ago. That machine has destroyed multiple clothing items including very expensive sweaters and undergarments. It has destroyed biking shorts and just about anything of value. Even destroyed the bags fur delicate clothing. I have to get a repair guy out every year to replace the bellow too! It is terrible!!!

Bought a Whirlpool refrigerator at Home Depot in 2018. It has been a $3,000 piece of junk!! Customer service is garbage!!! They refuse to address a persistent problem since the day we bought it. Do yourself a favor and buy another brand!!

My silverware, when it is washed, a piece or two comes through one of the openings in the basket and I have to work it out before I can lift it out of the dishwasher (MOD WDP320PAD50 Serial #F4432749) to put the pieces away. Please update your dishwasher by making the openings smaller for the silverware so I can stop cussing. Send me a new basket when you do. The dishwasher was in a new home I bought.

We purchased the Whirlpool Double Oven Range model GGG388LXS in April of 2011. The reason we purchased the oven is that we are empty nesters. We almost exclusively use the small top oven. We have streaks between the double glass on the bottom oven. We can not clean it. It is obviously a design flaw. I looked on this site to see if others have the same problem as it is too early to talk to customer service at Whirlpool. How have others fared with this obvious flaw?

I purchased a new French door refrigerator in May of 2016. Professionally installed. Last May 2017 icemaker stopped working and was replaced. June 2018 icemaker stopped working. This part of the refrigerator is poor quality and because of that I will never purchase another Whirlpool appliance. They use to be good quality and dependable. Not anymore.

Whirlpool Refrigerator WRF736sdam13. Purchased from Lowe’s June 2015... freezing started in April 2019. Freezer bottom is not draining correctly and the bottom keeps freezing making it difficult to push door close. I have the extended warranty. This will be the 5th time on Monday, July 29 repair person will come out.I talked to Whirlpool and Lowe’s. The product cannot be considered a lemon because the problem continues to be “fixable” as stated from answering service when I reported the problem again. Customer service has been amazing up to this point. Anyone else have an issue with this model with the bottom freezing solid? Any suggestions?

We thought we were going to love it. It has two bottom freezers so the capacity is fabulous, but the ice maker location subtracts shelf space. Love the French doors, but we can never find anything quickly. The biggest issue is the popping noises it makes that are sleep stealing in the night.

The wash machine is JUNK. We paid $2500.00 for our washer & dryer at lowes in 2012. I HATE IT from the start. It has destroyed most of my clothes. I hate doing my clothes. The water does not get my clothes wet, they dont get them clean AND the washer dont even get them wet. THEY need to do a recall or get us a lawyer. ALL the money I have put in this washer. The price we paid for them is a SHAME. IT is WRONG they are telling people that this washer is the best. They lie. I HATE HATE THEM.

I bought all new Whirlpool appliances for my house. After three years, the dishwasher is now broken and the washing machine is now broken as well. The refrigerator has had service two times in the past three years. The only thing that works is the stove that I bought. Whirlpool is all junk.

I bought Whirlpool dishwasher (silver, Golden Series), after one year it just stopped for nothing and the circuit controller failed with error code E2/F2. So it was expensive but turned out to be totally unreliable. I had to pay $200 to get extended warranty and still waiting for the parts!!! Worst experience ever (uh Golden Series, for me it is Plastic Series). Will never buy any product from this company again.

I love my Whirlpool Washing machine. Purchased it 2 yrs ago & have not had any issues. Its quiet, large capacity. Washes my clothes very clean. The various washing cycles makes it so convenient to wash as much or as little as I need on any occasion. I do recommend to anyone that you do the cleaning cycle on these new washers to ensure top performance when washing.

I was so excited when my husband bought me this as a gift this past year as we are a family of 6 which means lots of laundry. The first few months I assumed it was operator error trying to learn how the new one worked. Well here we are months later googling why it makes my clothes dirtier coming out than they were going. It leaves black linty looking streaks on all my white clothes, both inside and out and leaves white linty looking streaks on my darks, also both inside and outside. It DOES NOT REMOVE PET HAIR AT ALL! If you purchase one, and have long haired pets that shed, expect to invest in some lint remover. Im on my third type in an attempt to save me time. I will say OxiClean laundry detergent seems to be the only detergent that actually cleaned the clothes. Sadly, stores around here stopped selling.And whatever you do, DO NOT USE LAUNDRY PODS. It DOES NOT DISSOLVE THE HOUSING AND LEAVES SLIMY RESIDUE ALL OVER YOUR CLOTHES. I believe this is due to the fact that despite the setting, it uses little no hot water. Which would be great if it actually cleaned your clothes. I could run my clothes under a faucet with no soap and they would cleaner than this pos. Bottom line. Dont waste your money and if you do keep your expectations very low!

My ref. stopped working. I troubleshoot it and did not work. I filled out a service request back on February 2nd, 2015. I got an email back from a subcontractor called Active Appliance INC. with a date service on February 6th, 2015, 4 days after my service request, and that is the only available date. The technician arrived while I am not at the house, however I talked to him before he started the work on my refrigerator and asked him kindly if he can call me after founding the issue, and he assured me that he will. No call and when I arrived home I found that he told the attendant that the refrigerator is not working and he has to report to the office. REALLY! We know that! Anyway I called Active Appliance and the customer services rep. told me that she could not answer with the diagnose until she speak with the technician and that will be Monday February 9th, I asked if I could speak with a manager, and her reply was Our managers do not talk to the customers. I had to hang up and call Whirlpool customer services and spoke with a nice gentleman, that he was not happy with Active Appliance INC. services. He placed me on hold and called them and within 3 minute he got back with the news, what was wrong with the refrigerator, electric computer panel burned out and then the fan continue to work with no stop, so it burned as well. He assured me that the services will be done no later than Tuesday February, 10th.While on the phone I got a call from active appliance and this time she wanted to know if I am warranted. I told her that I have Whirlpool on the other line and they assured me that I am. She said that it does not matter and she has to get something in writing. I placed her on hold and talked with Whirlpool and he assured me that he will contact them and email me a confirmation, which he did. By Tuesday February 10th, no call no follow up. I called Active appliance and they stated that it would take up to 14 working days for a part to arrive. I called Whirlpool and spoke with a customer services manager, and she got on the phone and told me that they are going to do their best and get back with me. Today February 16th I got a call to cancel a work service order due to technician calling sick and reschedule for February 25th Wednesday, I told her that they did not call to schedule the service first place, her answer was Never mind, I am calling to cancel anyway. Would you like to take this appointment or NOT? I asked her kindly to reevaluate their service procedures and the way they handle their customer, and I told her that I bought my refrigerator from Whirlpool and they are the company in charge of their product and I do not wish to continue this dialog with Active Appliance!I called Whirlpool and the customer service gentleman was helping me and we got disconnected, however when I called back they were closed for the day, however the customer service has my phone number but I got no phone call!!!! I think this is the worst POOR service I got within the last 20 years!!!!! I hope someone at Whirlpool care about their services and can contact me to handle the issue.

My refrigerator is now 5 years old. I have a stainless steel fridge. I didnt even have my fridge for 2 months and the one door started to rust. Whirlpool did fix that but now my fridge isnt staying cold. My extended warranty was just up 5 months ago. Figured some of the repairmen that we have called wont touch our fridge because they say the model that we have breaks a lot and that Whirlpool discontinued making this model. I am disgusted with this fridge.

I own a Whirlpool Cabrio washer, model #WTW7800XWO. The lid to the washer has completely detached for lack of a better word. It literally blew-off during the spin cycle and is hanging on by one hinge. My husband is disabled and I have had to go without using the washer for several days, waiting on a repair person not to mention the expense that will be incurred.This was a very potentially dangerous situation. My washer is barely older than one year. To add insult to injury, when I contacted the customer service department, I was told I would have to purchase and replace the lid or pay $299.00 for warranty insurance to have it covered because this is not considered a Quality Control issue.The service person has told me that both hinges and the lid will have to be ordered and replaced, leaving me without a washer for several more days. No one has been able to tell me why this happened. I fear this happening again after repair and do not feel safe with this washer. I would appreciate a response as soon as possible.