The space could be laid out a little better. The flimsy shelf is not real stable for foods or ice tray. Where the shelf locks into the side wall is not deep enough to stabilize the shelf itself. The flat indentations in the bottom, where they meet the front, have an edge that makes properly cleaning the freezer a bit difficult.

I purchased this washer over 8 years ago and we have been using it 3 to 4 times a week/ 52 weeks a year since. It has performed flawlessly up until about a year ago when it kept given me uL error. Everytime I wash the basket always spins wobbly and unbalanced it seems. I checked the Internet and it turns out others have had the same problem. The solution was to replaced the 4 springs supporting basket and that fixed the problem. Been working ever since.

Large tub capacity. Door opens wide without stopping. White Finish has not faded or chipped. Quiet and rarely makes noise even when overloaded. Machine bought 12 years ago and has never needed a repair visit. It has been moved from 2 different locations by using the special brackets. Easy to use detergent holder and fabric softener.

Whirlpools front load washers do not have easy access to the drain pump filter. The entire front of the machine including the door has to be taken off to access the filter. When putting washer back together the parts are cheap and screws break. Most companies that sell front load washers provide easy access to the drain pump filter. Buy one of those instead of a Whirlpool and you will save yourself a lot of time and hassle.

Our Whirlpool refrigerator has been an extraordinary kitchen appliance, it may even be 28 years old. The ice maker worked until just four years ago and thats amazing. Its never been serviced and never needed a repair. I dont know what one can say about something thats worked so flawlessly. This seems a little bit trivial when considering the cost of a new appliance, but the plastic veneer on the handle had fallen off and needed glued back on, but thats about it as far as maintenance and repairs go. Overall its been an ideal purchase and I wish wholeheartedly all my purchases were as good as our whirlpool refrigerator.

Like many others Im experiencing the same sensor problem with my 4-year old Whirlpool oven. It wont start even after opening and closing the door multiple times as directed. I installed this oven to replace the original Whirlpool model when it died after about seven years. Im absolutely done with this thing. How frustrating when you find out that your guest isnt able to a forgotten cup of coffee that went cold. I thought to call a repairman but after reading all the reviews, I feel its better to switch brands.

Our new fridge, which was already an exchange from another unit that went bad, kept freezing things in fridge compartment. A tech was sent out three times and then the compartment quit working completely. They stated they would replace for us, only way they would replace was to have them ship a new unit which would take two weeks. So we are without a refrigerator for two weeks. Asked if I could go buy one and be reimbursed. I could but I would NOT be reimbursed for full amount. The company reps I spoke to could have cared less about our situation especially Fred who supposedly is a supervisor. Do yourself a favor...DON’T buy Whirlpool. Their customer service sucks!!!

I bought a Whirlpool over the stove microwave. It was to replace a GE that was over nine years old. 40 days after purchase and installation the plastic started chipping and peeling. I contacted Whirlpool customer service and was told that it was a cosmetic problem and my warranty stated that I had thirty days of warranty on cosmetic problems. This was a problem because chipping and cracking didnt happen within 30 days. The chipping and cracking continued to get worse. I again called customer service because the warranty stated that workmanship and bad parts were covered up to one year. I was told that because it was over my stove that this was to be expected. I thought this was a dumb answer because had I known that an over the stove microwave would have problems from cooking I would have installed it in my living room over the television. I called customer service several times. One of the times I called I talked to a representative who actually acted as if she wanted to help me. She suggested sending an e-mail with pictures and gave me an e-mail address. I did this and got no response. I was getting close to the warranty expiration date. I called again and was told that pictures wouldnt work; I would have to pay to have a serviceman come out and write a statement saying that it was not cosmetic. The cracking and chipping is so bad that I cant clean parts of the door because the cloth or sponges catch on the cracks. The door on the GE microwave did not look as bad after nine years of use as the Whirlpool does after 1 year and 8 days of use. I am not the smartest person in the world but I know the difference between poor quality material and workmanship as opposed to cosmetic problems. Im pretty sure that if my wife put her makeup on and pieces of her face started cracking and falling off she wouldnt want to hear that it is not a real problem its only cosmetic. Bottom line is I am very dissatisfied with the poor customer service and warranty problems I have experienced. I will not buy another Whirlpool product and would strongly suggest to others to buy any brand but Whirlpool.

Cabrio Washer - I am so disgusted with this product. After only a few months service came out and the repairman told me it was normal for a load to run for 8+ hours. Second repairman replaced the circuit boards and it has lasted 11 weeks. Now it is not working again. Calling tomorrow. I have a bad feeling about what the end result will be. Expect I will be buying a new washer, will not be a Whirlpool. Just went and tried what another reviewer does to get it to run... Pause/start/pause/start. After 8 tries it is now running. I will not live with this. Not going to spend a dime to fix this piece of garbage. Still have 36 days left on extended warranty.

Here in Brazil, we use to have a very good brand of durable and reliable refrigerators and home appliances called Brastemp, and I was a very happy, fidelized customer of theirs. The time came for me to move to my new house. I gave my old appliances away to friends and modeled my new kitchen with Brastemp products. What I didnt know then is that Whirlpool bought the brand in 2000 and was selling their appliances over the Brastemp brand since.Whirlpool is clearly selling disposable appliances here. My vacuum cleaner failed after a week. My brand new refrigerator and laundry machines failed weeks after the one-year warranty and the dishwasher sometimes heats up and tips the 20A circuit breaker (suggested by the manufacturer), which is only for the dishwasher. For my complete surprise, my old appliances are still functional in my friends house. I got my old dishwasher back and I had absolutely no problems since.The vacuum cleaner failed again, this time 5 months out of warranty. In all fail cases, the price to fix it was about 70% of the price of a new one, which I took as a sign to replace them for something else. Good job, Whirlpool! You bought a nice brand, trashed it and gave the finger to fidelized customers you acquired with the new brand by replacing quality products with built-in obsolescence others. What do you plan to do next? Whatever it is, dont count on me as a customer ever again.

Whirlpool makes a beautiful product that does not last. I bought model WRX988SIBM in April 2015. Two years later the compressor is bad and no warranty coverage. Do not buy this model. It does not carry the Whirlpool 2-5 year sealed refrigeration warranty. Its amazing that an appliance that retails over $3K only comes with a 1 year sealed refrigeration warranty when Whirlpool offers it on other models. Be sure you know what your warranty coverage is before you buy any Whirlpool product.

We bought the over-the-range Whirlpool microwave, model #WMH53520AH-1, about four years ago from Pacific Appliance Sales Kitchen and Home inside a Best Buy store in San Diego. The Magnetron and Diode have malfunctioned and been replaced. Now the plastic around the door is falling apart, cracking, and splitting. This is unacceptable, poor craftsmanship, and low quality for the price of this Whirlpool appliance. This needs to be reported to the company and properly addressed. Until then, were staying away from any Whirlpool related products. We also own Cabrio W/D. The washing machine has had problems from year one. Im submitting a separate review for this appliance. Consumer beware!

We purchased a Whirlpool stove a year and half ago. We were cooking and kept hearing (tick, tick, tick) noises. Couldnt figure out what it was. After removing the pot there was an area of 2x4 inches that had melted in. Not sure where the glass went. But it looked like a chip but on the surface.

AVOID Whirlpool water heaters - Bought two 12 year warranty water heaters from Lowe’s in 2014. Model NU50T121-403 from Whirlpool. Thermocouple went out within the first 4 months. Called WP, they gave me a number to call for an authorized contractor to come out. Made certain to tell me that PARTS were covered, but not labor. $300 for the labor and two days later, hot water is back on. SAME THING happens again 6 months later, then AGAIN in Sept of this year. So 3 guys have been out to all replace the same part. This morning, hot water is out. Both tanks. Can’t keep pilot light lit. Called WP. They gave me more numbers of authorized contractors. No hot water and now I’ve got another $300 I owe to fix the SAME BROKEN PART. I wonder if this is how their last class action lawsuit got started?

My silverware, when it is washed, a piece or two comes through one of the openings in the basket and I have to work it out before I can lift it out of the dishwasher (MOD WDP320PAD50 Serial #F4432749) to put the pieces away. Please update your dishwasher by making the openings smaller for the silverware so I can stop cussing. Send me a new basket when you do. The dishwasher was in a new home I bought.

Buyers beware of Whirlpool ovens! We bought a Whirlpool Built-In Electric Oven in August 2008. Fifteen months later, I decided to clean the oven for the first time and when I turned it on the auto-clean, the entire control panel went dark. The technician said he has seen this problem several times in such ovens and was able to repair the oven. I called Whirlpool and they had not heard of this being a common problem. Last week, the air blower wasnt functioning and had to be replaced. I called Whirlpool again and told them about this second incident in a 4 year old oven that is not used frequently. I told them their quality assurance people and/or engineers need to re-evaluate their products. My lesson learned is that I will never purchase another Whirlpool or Whirlpool related product.

We bought a Whirlpool with convection oven, it is beautiful and very well designed and fully electronic. You can only control it via touchscreen Which, when the software runs into blocks, it is impossible to troubleshoot efficiently, you just have to wait until it completes its rebooting. It is very frustrating to spend hundreds of euros in a device you just cant control when it crashes. Horrible programming made for a horrible user experience. You have the feeling of not being able to use it or fix, it is like having a mobile phone or computer Which only works on what appears to be a random logic. The errors displayed on the screen are often vague and the user troubleshooting manual is just plain short. We will return it without doubt and dont recommended ever buying this device.

Whirlpool Cabrio Washer - Sucks. I purchased it when I purchased my house. After having the washer for a year and a half it stopped draining and wouldnt spin. I paid $75.00 for the service call from my home warranty and thought that I was good to go for a while. But here I am a year with the same problem. I will never buy another Whirlpool again.

On 5/3/16 I purchased an Amana high-efficiency, low water, top loading washer. What a joke, it is a piece of junk. There is no water so clothes dont come clean, and if you leave money in the pockets no worries. As it will be right there after the clothes are washed and dried (got matching dyer also). They dont even smell clean after two washing. And now you are to purchase a cleaner to clean your washing machine. This is truly not an efficient machine in any way.

Me and my wife bought a Whirlpool top load washer June 2011. Two months later the motor locked up and they repaired it; then the transmission started whining the next month. It was repaired. Now a bearing is going out all in the first seven months of ownership and they will not exchange washers, they just want to keep fixing this one until the warranty runs out. Whirlpool washers are a piece of junk and I will tell everybody not to buy anything Whirlpool.

We bought this washer from Sears with big hope. Within the first year, we had 14 service call covered by the warranty but required 2 to 3 weeks in doing without. Whirlpool replaced the washer at no charge but continued to have various issues over the years. The new one is the control module that Whirlpool knew was faulty but did not let their customers know. The control module went over the weekend but I repaired it myself and do not have any more issues. I literally went in and tightened all of the hardware, removed and install the pulleys, motors pumps and replaced a lot of keep components with better quality. Guess that year the CEO made only 20 million rather than 19 million. Being an American company I was disappointed by the consumer relations people but everything is a throw away nowadays. Will not buy a Maytag or Whirlpool product again. Where has American product pride gone?

My mother purchased a Whirlpool gas stove. When the stove arrived the door didnt shut properly. We were told to contact Whirlpool. They sent a repair person out who said that you have to use the stove a few times first and then the door would close. Meanwhile, I had a 2-inch gap and gas and heat escaping. I called and requested another company to come out and check it. No one called back. I called again and they sent out the same repair guy. Apparently hes the only one in the whole Charlotte metro area that can service Whirlpool. Again he said I had to use it more. I called again and requested a different repair person to come out. They promised to send out a lead. When the company called to confirm the appointment they said no one told them that. They finally sent out a different person. That person said absolutely the door was dented. He offered to replace the door. He then came back and said the door comes in too many pieces and he didnt want to put it together so I should contact the store I bought it from and see if they would replace it. Whirlpool refused to repair it. I was able to get the store to replace it after explaining to them the problems with the warranty service. I filed a complaint with the BBB and they lied and said they tried to contact me which never happened. When I called the executive office I was told that I was the problem and that it was resolved so leave them alone. I regret my purchase of my appliances and now have no one to stand by the warranty.

I purchased this Whirlpool Gold dishwasher a year and half ago, and it needs repair to the tune of $300.00. The drain pump broke and need to have it repaired. If this was the only Whirlpool appliance that went bad, I wouldnt even write a review, but two months ago my Whirlpool refrigerator, one year and 4 months ago, the ice maker stopped working, another $300.00. Whatever you do, do not purchase any Whirlpool products, pure junk. Their customer service is even worse. What a nightmare.

I purchased the Energy Smart Gas Water Heater about a year and a half ago, intending to install right away as part of our upgrades. Just now, I was able to install this replacement to our 30-year-old water heater that was showing problems. When trying to start the unit, I kept getting the response that the lower sensor unit failed. We contacted plumbing companies. We were told they would not work on any Whirlpool models purchased from Lowe’s, because they were the worst hot water heater ever made. I called Whirlpool support. They wouldnt put me through to a tech support person until I was registered in the system. I gave up trying after many minutes of frustration.

Whirlpool top loading piece of junk! I would give it a zero star review if I could! Do not buy this machine!!! I agree with many other reviews. It doesn’t get the clothes cleaned and now a completely doesn’t work. We reset it, we’ve had the service guy come in and replace a bunch of parts on it. It’s past its one year warranty and doesn’t work anymore. Piece of junk! Junk, junk, junk!!! Waste of money. Do you not buy the Whirlpool tub loading washing machine!

I have a Whirlpool dishwasher for a few years, it cleans great, works great, the dishes come out clean and shiny, so do the glassware. Even pots come out nice and clean, what more can you ask for?

I contacted Whirlpool in regard to one of their water heaters we purchased from Lowes. It came with a 5-year warranty. At the end of 3 years, the lower element went out. Our plumber took the part back to Lowes, where he stated they normally just do a part replacement with them. On ours, he was told the owner would have to contact the manufacturer. I contacted them and supplied them with the plumbers bill and copies of the front and back of our canceled check, along with all my contact info. Their website states theyll get back with you within two days. I contacted them on March 13, 2013. Today is April 7, 2013 and they havent emailed, called or snail mailed me. After reading these consumer reports, the air has been let out of my balloon. No more Whirlpool products for me! Integrity in our country used to be extremely high. Today it is extremely low as demonstrated by the complaints on this website and now mine. Hey Whirlpool, you suck!

I am waiting for the third repair on my front-load washer. I purchased them a year ago and was very satisfied with the ease of use. But in April of this year, the E2F3 started flashing up after I put in a load of clothes. I called the repair line and they sent a guy to check it. Determining it was a sensor, I waited three days for the repair. Then, almost two months later, now, it did this again. He called WP and they said to replace the sensor again. I waited two days for the repair. Before he left, he started the washer to run through the cycle - no problem. I then put in a small load of clothes, and almost immediately, the washer stopped and the E2F3 was flashing again. I called for a repair, and am again waiting (without a washer) for the repairman to come back on Tuesday!!!Today is Friday. I have been four weeks almost without a washer this year. Thats also the $20 I have spent this last week to wash clothes at the laundromat, not to mention the frustration of waiting for the warranty line to pick up and the hassle of having someone here when the repairman comes. I am glad I purchased an extended warranty for this product, but Whirlpool should make their products to last!

Purchased a new range from Lowes in November. It was delivered in January. Was told upon purchase that there was a one year warranty on the item. After using the item approximately three times, a piece of aluminum foil fell to bottom. It stuck to the bottom and removed some of the porcelain. Bacon grease had spilled into the middle of the oven which caused the oven to warp and also discolor the porcelain. They sent a tech out, who called Whirlpool. Whirlpool told them that it was cosmetic damage and only had a 30-day warranty! They also said I had to contact customer service again, which I did. Customer service said that the tech didnt do what he was told to do and that they would send someone out again. The same tech came out, called Whirlpool again, and was told there is nothing that can be done. I asked to speak to a supervisor because I was unsatisfied with this response. A two-month old oven shouldnt look like it is five years old. I never spoke to a supervisor. The rep just kept telling me that there was a 30-day warranty and that it was stated in my manual. After insisting that I speak with a supervisor, she placed me on hold. After a few minutes came back stating that she is sending my request to another department and that they will call me back in three to four days with their decision. I would not purchase another Whirlpool appliance even if they decide to replace this one, which I sincerely doubt that they will. VERY POOR CUSTOMER SERVICE!

DONT BUY WHIRLPOOL! I bought a Whirlpool refrigerator 5 years ago. In June I had to have a new thermostat put in because the refrigerator would not stay cold. The food in the freezer would defrost and then freeze, defrost and then freeze. I had to throw all of the food out. Two weeks ago the refrigerator was making a groaning noise so I looked in the freezer and the temperature was up to 30 degrees. The ice cream was soft, the bread and buns that I had in the freezer were defrosting and small things like crab cakes had also started to defrost. Eventually the temperature went back down to zero.So I called out the repairman AGAIN! He told me this is normal that the freezer goes up to 30 degrees to defrost the freezer and the groaning noise I heard had to do with the Freon. It cannot be normal for food to freeze, defrost and freeze again. I called their customer service and their representative, Jasmine, basically told me all she could do for me was to schedule a service call. Really? I just had the repairman out the day before. I am concerned about food safety with a refrigerator that fails to keep food at the proper temperature.

Whirlpool Quiet Partner II Model # DU1055XTUS1 - We bought the dishwasher in Aug 2010 and after the 2nd yr, it started to occasionally shut off by itself in early cycle. After 3 yrs, it now shuts off repeatedly... needs to be restarted at least 15 times. It use to shut down early in the cycle. Now it shuts off whenever. I should have read the reviews on this dishwasher before buying but it was on sale for such a good price. I guess I got what I paid for. Just keep in mind that Whirlpool dishwasher seem to last only 3 years. I guess thats also why their warranty for electrical parts is one of the worst compared to other brands.

My Whirlpool dishwasher washes dishes well, when it drain but it will not drain. I purchased insurance repair service from AIG. AIG is a total rip off. I paid them over $300. I have called many many times. They promise someone will call but not one ever has. I would never work with AIG or Whirlpool ever again.

I purchased this washer about 3 years ago to replace a dishwasher which lasted 20 years. Within a year the racks began to rot, the front panel plastic started to peel off. Within two years half of the racks rods completely rotted away. 3 years later the washer is busted - most likely pump which was probably blocked by one of the pieces of the rack rods. I am replacing it with Bosch - German engineering. Needless to say I will NEVER buy a Whirlpool - formerly reputable company again. Good-riddance Whirlpool.

We purchased the model WFC7500VW, 24” washer and accompanying dryer in June of 2015. Within a couple of months, the water pump went; also we continually had to take the front panel off and clean out the filter when we get an A11 code! Now we experienced an F06 code... This code means the washer can’t go into high speed. The repairman (Whirlpool recommended), told us that a new tachometer motor, etc would run $500-$800 with labor! He also said that the noise the drum made was bad. My dryer works fine (only complaint is the grinding noise it makes, which Whirlpool told me is normal)... I would like to purchase a new washer, but don’t know what will fit under the dryer. I do not want ANY Whirlpool product!

Even with the hottest water on the most heavy duty setting, regular dinner plates are not cleaned. The flatware holders that are set in the door (instead of free-standing in a rack) do not have adequate holes in the holders and are too far away from the limited jets to get adequate soap and water to cleanse the flatware. Even after rinsing all scraps off the plates and flatware, we find bits of food, gravy, or smudges on the plates and flatware - since its first usage. The manufacturer had the audacity to claim that was normal. Settings include delayed starting, heavy duty versus normal washing, and different types of drying. The heavy duty washing is definitely poor quality, and there seems to be no difference between any of the drying settings. The delayed start is nice. The physical layout of the prongs on the racks and the folding racks do not allow easy fit for most sizes of pots plus plates on the same bottom rack. I cannot put a 1 gallon pot level on the same rack as dinner plates. I must put it beside salad plates. Only small sauce pans fit neatly or cleanly beside dinner plates. Yet the external dimensions of this dishwasher are the same as the competitors standard size. Looks neat and is easy to clean. Also, the exterior does not show scratches. Actually, I cannot see where the exterior has any scratches. The service people were very little help. The Warranty said that after five (5) service calls the unit would be replaced. We made six (6) service calls, but we were told that we did NOT have six because if you called again within 90 days of a call, that was considered the same service call. That requires 450 days minimum to have five (5) qualified service calls, but that warranty was good for only 365 days!

My son purchased the Whirlpool 2 door w/ icemaker about 3 years ago. Twice weve had a repairman here. Yesterday was the 2nd one. He tried 3 ways to get liquid to go through a round coil I could see at the back. He said the problem was between the two back panels (back of fridge & inside wall) where there was a tubing to release the water from defrost cycle. It appears to be a manufacturing problem. I am very upset! It should be replaced at the very least.

I bought this Whirlpool Cabrio Top Load Washing Machine in December and have hated it ever since. The energy efficiency this item claims means that you will spend a ridiculous amount of time waiting for your load to finish. My family hates this machine and I regularly have to hear about how long the load is taking because the timer adjusts continually. Put in a QUICK load and it said 38 minutes, came back in 30 and it said 24 minutes. It is so frustrating!!! We are afraid to put anything on a heavy soil setting or anything other than quick, because it can take 2-3 hours to complete. I have to schedule a day to wash my bedding and there isnt any convenience in doing a quick load. I am going to have to sell this one and purchase another washer. What a loss!! This machine has been a time and money waster! I will NEVER BUY WHIRLPOOL again!!! I bought this machine through Best Buy.

Outstanding, however our location has a hard water rating and as such we have to use a deodorizer to balance this out. A wide range of variables which are a fit for my purposes. Interior dimensions and layout are more than perfect for my uses. This particular dishwasher is built in so blends aesthetically into the design of the kitchen seamlessly. The product has a drying system which successfully blows air over the top tray to eliminate wet areas within depressions of crockery, glass, and so forth, its excellent. There is also a light steam setting which removes tough deposits from surfaces.

I used their website to schedule an appointment for an estimate for a repair on my oven. I was never told they were sending an independent contractor to do the repair nor that there would be a charge for the estimate. I contacted Whirlpool and was told there is nothing on their website and I should have asked the service technician before he was at my door if there would be a charge. Therefore, it was my fault and I indeed had to pay the charge when I declined to have my oven repaired. I paid an independent contractor hired by Whirlpool for $129 to give me an estimate on the repair to my oven despite never being told of such a charge prior to the appointment.

My 2-year-old Whirlpool Gold Series model replaces a 20-year-old Roper. So far it has exceeded expectations for low noise and useful features like validated Sani-Rinse. Has all the normal features plus Eco-Dry, Sani-Rinse, delayed start, five levels/cycles of cleaning, and hi-Temp wash. Fits where the old Roper used to be and handles a full load of dishes with room to spare except Thanksgiving, which takes two loads. Smooth black front with touch buttons and blue lights. Looks nice. Using Sani-Rinse seems to take a long time, generally around 3-hours for a full wash cycle. Besides being ultra-quiet, the unit is very energy efficient earning good Energy Efficiency and water efficiency ratings.

Regarding a Whirlpool Refrigerator (model ET8CHMXKQ04) purchased in 05. I dont remember exactly when the problem began but the freezer starts its defrost cycle, water drips down through the refrigerator compartment (soaking all paper/cardboard covered products), collects under the crisper trays and eventually spills out onto the floor. Its a river of water that requires a towel to collect.I believe whats missing is some sort of collection funnel and tube that catches this dripping water and delivers it to the evaporation tray behind the base cover plate under the refrigerator. Obviously, Whirlpool has no quality control nor does it do any field tests to ensure their products are designed and operate properly.

Stainless steel side-by-side refrigerator (4 yrs. old) - I have to continually clean the rust stains. Ive used the products Whirlpool has suggested and the rust continues to appear. Lowes extended warranty does not cover this problem because it is cosmetic; Whirlpool reps say its due to the coastal area where I live and that they cant do anything about it! I understand that there are many customers experiencing the same problems with Whirlpool products. Their customer service is worthless and is their warranty to stand behind their products!

We purchased a dishwasher for $650 and within a very short period of time, the upper rack was so squeaky that it was intolerable. Service guys came and replaced the rack and wheels and all was well until a few months passed and it happened again. At that point, it was outside of the warranty, so we called upon our extended warranty we bought through Whirlpool. Guess what? That warranty doesnt cover the racks. So they referred us back to Whirlpool. They told us we had to pay for it ourselves. After being treated like a ping pong ball several times, we ended up paying about $150 for labor for another guy to come out and replace the racks again. Whirlpool agreed to pay for the parts. A few months later, we again have a squeaky upper rack that is so loud it wakes people up in our house and its less than two years old at this point. Weve been sold a LEMON!! Just got off the phone with a supervisor at Whirlpool who said they cant do anything about it and wont acknowledge we have a lemon. When I told her I was going to take this as far as I need to to resolve it, even if we have to go to court, she laughed out loud at me. We will never again buy a Whirlpool product. Our LG appliances have been great however.

Im so disappointed with this product. Its only a couple of years old, which seems fairly new as my old washer was over 20 years old when I finally got rid of it because of the noise it was making! First, the Cabrio stopped draining and spinning, even though the display showed that the cycle was done. Phoned Whirlpool, and the best they could do was send out a repairman - at our cost, of course! We refused, and kept using the machine - put it on for an extra drain and spin. Then, it stopped working completely! My husband hauled it out to a repair shop and was told it needs a new motherboard at a cost of $400 plus labor! This was an expensive washing machine, and I feel Whirlpool should offer its customers better service! I guess we need to buy a new machine - definitely not Whirlpool!!

Our microwave is less than 8 months old, hardly used and only for heating items. Besides the point, being under a year old. It began to make noise and pop, spark sounds with the smell of burning wires and promptly stopped working. We called the customer service line and began the long frustrating circle of completely bizarre conversation. Maintaining our belief this is a fire hazard and not wanting it in our home they insist on a repair person coming after trying to sell us Extended warranty, Why would we want Extended warranty when the warranty is NO warranty, it seems, whatsoever. After requesting to speak to a supervisor 3 times. A overly bubbly person comes on the repeat same spiel and to make an appointment for 1 week away from 8am to 4pm to be available for a phone call to make an appointment to see about repair on said fire hazard microwave that is less than a year old. This appointment is made with repair place and they too are confused and noted Whirlpool said this is not covered under warranty, and they too would contact them.Today Whirlpool Canada calls and gives number to repair place to book appointment, Hello we already have one and the frustrating verbal dance continues. 5 minutes after this call the repair place calls, as whirlpool contacted them as well to book appointment, which we both could agree this is the bizarrest situation since we already have an appointment, from their appointment. We keep saying we feel unsafe, this is a fire hazard. Which they completely ignore. This is unacceptable and extremely poor service.

I have called Whirlpool six times to request a replacement for a broken deli drawer in my refrigerator. I was told to throw everything away from the unit, since the whole assembly would come complete in the mail. First call: Ordered the replacement: what came was a glass shelf without a drawer or gliders and hardware. Second call: requested the drawer and remaining parts. Third call: only received the plastic drawer without any means of installing it. Fourth call: received only one side glider, again without hardware to install. Fifth call: requested a supervisor (Kimberly) who took the order for the remaining glider and all hardware. Received second glider and (1) screw when two are needed.Sixth call: asked rep Brigitte for a supervisor and was not connected. Given the run around and told that the rep spoke with a supervisor for me and would send out a repairman to assemble the unit. I just need the missing screw. I have spent a lot of time on the phone trying to get what I need from Whirlpool and do not have time to wait for a service repairman to come out. I just cannot fathom how that many calls - with me being patient and calm - cannot produce the required items. Horrible.

I bought my Cabrio washer 16 months ago to service a family of 4 adults, 2 children and 2 dogs. Anything that has the slightest stain has to be pre-rinsed or pre-washed in the sink before going into the washer. Every load is an unbalanced load. Although the floor is perfectly level, the washer bucks and dances as though it is possessed. I never expected a $900 washer to be a piece of junk. I would love to be part of a class action lawsuit regarding this washer.

I have a Whirlpool Cabrio washer and dryer set. The heating element went out on the dryer when it was less than a year old. I purchased the set at Lowes. They sent out a repair person who called and told them it was the heating element and he replaced it. Two weeks went by and I could smell something burning. I called Lowes and after two weeks wait the repairman showed back up. He said that the control panel was bad. Lowes replaced my dryer and I have not had any further issues with it. Lowes gets an A+. My washer went out about a year later. It was making the loudest noise on the spin cycle. The repair person came out about 2 weeks after I called and told me that the washer was basically worthless, that the repair would cost more than the washer would to replace. I was totally shocked and decided to use it until it died. In the meantime, I found a repair/used appliance place. They repaired it for $235 and it ran for about 4 months. Then the noise returned. I have had it repaired again. Now the control panel gives me the SE light and stops running with 27 minutes left in the wash cycle. I have had nothing but problems with this machine. I would not recommend Whirlpool to anyone. Im going to have to replace this machine and it has cost me lots of $$. Junk!!

After only 14 months of light use, the magnetron in my over-the-range Whirlpool stainless steel microwave failed. The cost to repair was $350. I paid $450 for the whole unit upon purchase. I wrote to Whirlpool with documentation and got a voicemail that they were sorry, but the 12-month warranty had expired. The independent repair person said it is the Korean manufacturer of the magnetron that is the problem. He is replacing units all over town on all kinds of models Whirlpool is involved with, including KitchenAid. Whirlpool needs to get their money back from Korea! I will never buy another Whirlpool product and have told them so.

Safety issue with Dishwasher Model MDB6949SDH. Fire hazard! Strong electrical burning smell when using powerblast function. Waiting for some Whirlpool action but does not look to be too soon. Chat noted a report to be filed with safety department and will hear from them. No hear so far. Pick up phone Whirlpool.

We have several Whirlpool products in our home currently and have been very satisfied with their performances. We have their fridge, stove/oven, microwave and dishwasher, all of various ages. We purchased them from a local big box building supply company and installed them our self. The installation directions are clear and simply for the average D-I-Yer. We would recommend Whirlpool to everyone shopping for these home appliances.

I am so disappointed, angry and tired! Unfortunately, I listened to the salesperson regarding this feature and bought it hook, line and sinker! The Aqualift self clean system is a joke! It only cleans the bottom of the oven and that is after you mop up the water left in the bottom and scrub it. No amount of scrubbing even touches the sides, back or window, even after using the Aqualift feature 3 times! I spent hundreds of dollars only to be down on my hands and knees scrubbing to no avail. I have not seen 1 good review regarding this system. Shame on me for believing a salesperson and shame on me for not researching first. I will not make this mistake again!

I bought a Whirlpool washing machine, model WTW4855HW, and was I ever shocked at how noisy it was. The wash cycle had a grinding noise that was just too much. After 2 loads I sent it back and didnt regret having to pay the restocking fee. I just couldnt believe that with all the technology we have today, that they couldnt build a quiet machine. Im an engineer so I know there are methods through gearing, belts, soundproofing, etc, to produce a quiet machine. Remember the dishwasher of days gone by. You couldnt watch TV with the dishwasher going. Nowadays, you can stand in the kitchen and have a nice conversation with it running. The technology exists. As a matter of a fact, my old Maytag that finally went bad after 10 years was fairly quiet. So, if you dont have your washing machine in the garage or basement room where you can close the door, dont buy this machine! Bruce in Portland

This washing machine started giving us trouble just a few months after purchasing. Have had repairman to our home 5 times in 3 years. Last time repairman came he said future repairs would be very expensive & we should purchase another machine. Whirlpool will not have my confidence again unless they recall this machine & fix all problems.

I originally purchased a Whirlpool hot water heater in 2005. After numerous problems Whirlpool agreed to replace January 2010. With the new hot water heater, everything was fine for the first two years. Now about every 6 months, we are having the thermocouple and the igniter. Each time you order the part, the part is free but you have to pay $30.00 for shipping. I am tired of dealing with this. We have decided even though we still have a warranty left on the hot water tank we are going to purchase a different one and never ever buy another Whirlpool product. They do not stand behind their products.

On April 17th mid morning I noticed that the freezer side was not keeping items Frozen. Everything was melting period. I then opened up the refrigerator side all the items are not as cool as they should be. I then proceeded to do a Google search to see what I should check for in regards to the freezer and the refrigerator side not keeping cool. I then proceeded to pull the refrigerator out to inspect the back of the refrigerator. When I did that I noticed there was a hot mark on my wall, as well as a huge it burn mark on my floor. I then unplug to the refrigerator do the huge fire hazard and I touched my floor and it was very hot to the touch.I called my stepfather who is a firefighter and had him come over right away. He said we needed to take the refrigerator outside right away because the compressor had overheated and that is why it started to burn my floor. He then went to the fire station and got a heat sensor check machine, and we checked my wall and floor and we had to make sure that it was cooling down so it did not start my floor boards on fire so then we had to put a fan on it to cool it down. I then went and purchased a new refrigerator, due to this one was no longer able to be used or repaired. The refrigerator was only four years and 5 months old. For a $1,300 refrigerator it should last longer than 4 years.I called Whirlpool the following day or two days later and regards to this issue. The only thing they could tell me is that they were sorry, this refrigerator almost started my home on fire and we have six children a family of 8. It ruined my floor and part of my wall in my kitchen and we have lost a few hundred dollars and groceries. This is ridiculous and not the first time, I read a few others having this issue, Whirlpool said they have never received any complaints in regards to the refrigerator burning the floor and does not see it as a fire hazard at all.

Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both ice makers went out, The computer on the filtration will go off. Refrigerator had problems maintaining temperature since 8.12.17. The refrigerator no longer works. This is my second unit since 11.09.16. It came from nfm.com.

Found a crack under a freezer rack from sidewall to back wall. This has caused the refrigerator not to operate properly. Every appliance I own is whirlpool. Bought in 2005. Also bought another in 1994 that is working fine. What surprise me is having a crack in freezer wall. Nothing Whirlpool can or will do! Was a lifetime Whirlpool CUSTOMER. GUESS WHAT? FACEBOOK I GO. 3309 FACEBOOK FRIENDS.

My family purchased a newly built home from a reputable homebuilder on December 21st 2019. On the first week of January 2020, we noticed that our upgraded Whirlpool dishwasher, model #WDT730PAHZ0 was shutting off mid cycle, resulting in dishes remaining dirty. The technician gave us an estimate of nearly $500 for replacement of pump motor assembly. He also informed us that this particular model is well known for having this defect. We are requesting that Whirlpool stand behind their reputation for producing reliable high quality products by replacing our dishwasher.

Whirlpool Microwave model #GMH5205XVS0 - Same story as many of these other reviews. Similar reviews on Amazon as well. We bought a new house early in 2011 with all Whirlpool appliances. We have gone through 3 magnetrons in 2 yrs. Now Whirlpool wont do anything for us. We will have to buy a new microwave. It just stopped heating all 3 times and the magnetron was replaced. Now it has happened again. Ridiculous. I will never buy a Whirlpool appliance again. This model # should be recalled. Its a lemon and sounds like it could be a danger as well.

This is an EXTREMELY dangerous range. The burner knobs leak - turn on with just a bump and leak gas. Any slight movement causes the knob to move and allows the gas to leak before the igniter ignites the gas. Has happened THREE times!!!! Has this product been recalled???

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

A couple years ago we purchased a Whirlpool Cabrio WTW8000 top-load, high-capacity, washing machine based upon good claims of the salesman at Lowes - Appliance Dept. This was not an inexpensive machine. However, this washing machine failed to live up to representations and performance is poor. However, biggest complaint is that clothes are able to get stuck between drum and the unique agitating device which results in holes and tears in material. This is a significant design flaw and were not sure why more people dont complain about this rather significant design flaw. Of course, there are other shortcomings... but destruction of clothes is a serious problem. While this machine is in excellent condition, it will be replaced with a more traditional washing machine with vertical agitator ASAP.

I recently purchased a Whirlpool Slide in Oven replacing my Amana stove of 15 years. My Amana was a very basic model, and I thought this WP was an upgrade. But it is so poorly made its ridiculous. First of all the bottom storage drawer, is so flimsy, it does not slide out easily, and the top lip doesnt even have a finished edge. Additionally there is a 1 inch gap between the top of the drawer and the bottom of the stove door. But the BIGGEST disappointment was the oven racks, totally flimsy.We used a Lodge Dutch Oven (which we have used many times with our old stove) and the oven rack sagged under the weight. Had I known I would have pulled the racks from my old stove. I contacted that seller about these issues, and they said they are ALL like that even the higher end ones, and I contacted Whirlpool to see if I could buy better quality racks and they said no, this is all they have.

My refrigerator was purchased in May 2014, and died in August 2015. Before it died, it produced a very loud, rattling noise for two days. Thus, the refrigerator cost me $100/month. It does seem, upon reflection, I would have been better off buying a piece of junk for $50. It would have lasted longer. Additionally, the so-called stainless steel started rusting all over the front surface, first popping up in one spot, then another. One year old, rusty and dead. Great job Whirlpool. Buy American.

Purchased 03/28/13. Refrigerator 62 degrees on July 4, 2013. Called for service July 5 - came out July 9 and told unrepairable - wiring harness set against tubing rusted and broke wires. Since July 9, I have been trying to get my replacement from Whirlpool and always told they will call me 24-48 hours - never calls. Asked for supervisor on July 22, then asked for her name and direct number. Supervisor said someone would call me about delivery. Supervisor told me if a local store would have had in stock, they would have sent it out from there (called local store and was told 6 were in stock and could be delivered tomorrow). Tried to call supervisor back to inform her, but number would not go through (apparently bogus number). As of July 22, 2013, still no refrigerator. Very poor customer service/service repair. July 24 - asked if I needed to get an attorney and/or contact local new consumer advocate - Whirlpool said they would issue a refund check for the refrigerator, and that I should receive it in 14-21 business days - said they could not refund on credit card I used to make original purchase. Hopefully, the check will arrive.

We bought a Whirlpool freezer-bottom 18.5 cu ft. fridge from Lowes. The compressor broke in less than three months of regular use. I called Whirlpool who sent A&E to check it out. The technician didnt even file a report and lied to me about what was wrong with the fridge. They sent a different company to come look at it and they confirmed that the compressor is broken. I called Whirlpool customer service and was told that the warranty only covers repairs not replacement even though I paid over $1,000 for a defective product. The excuse: Its a man-made product so we cant guarantee it! So what used to be a 3-5 year warranty not too long ago is now what? A one-year warranty is virtually useless. I can see a future not too far off where there is no warranty at all. Where is the protection for the buyer? If I wanted to purchase a second-hand fridge, I would have. I will never buy Whirlpool again.

Whirlpool 500galaxy gas water heater - First week ran great. Now Im lighting every day. Called Whirlpool and just getting run around. Had it a month today, still lighting every day. Cant afford to buy another.

I bought a Whirlpool water heater from Lowes. I had trouble with it from day 1. It never worked correctly. Their service department is terrible. All they want to do is sell you extended coverage policies on it. Every time I have it fixed, its never covered, and I have to pay again. You will be sorry if you buy a Whirlpool water heater.

We purchased a new Whirlpool water heater April 2013 at Lowes and every 3-4 months the pilot would go out. My husband would simply re-light the heater, I guess he didnt think it was a big deal. However, in September 2014 the water heaters pilot went out and would not re-light, so I contacted Whirlpool about the warranty. It took 4 telephone calls (two of which involved a plumber, per Whirlpools request), and several days of cold showers for an authorization code to purchase a $8 part (thermo coupler). The hassles that Whirlpool put me through, no one should have to endure. Who ever heard of a technician telling you that they have to talk to the plumber, when you call them to explain a problem with your water heater, such as, the pilot will not stay lit and the plumber said it is the coupler (I couldnt remember the whole name of the part, but surely they should have understood what was wrong). Secondly, providing a plumber (unless youre married to one) to converse with them involves more money. Now I have a plumber at my house so I call Whirlpool and this technician insists that the plumber perform a test on thermo coupler to make sure that it was faulty before she gave the authorization for a new one. Yet again, when I called to Whirlpool with the plumber, while I was voicing my problems in resolving the issue of my water heater with this technician, and she just hung-up on me. So as not to be defeated and having already invested in the expense of the plumber, I called Whirlpool again and requested a manager. The technician asked if she could help and I informed her of my previous encounters. She apologized and took my information to have a manager to call me later; however, she did give me the authorization code for the thermo coupler without delay. When I went to purchase the part, I didnt have the old part (as trade; the plumber hadnt removed it), so I paid for it out-of pocket, to return the old part later.

I purchased our brand new double ovens on 9/27/11. I was happy until 11/3/11 when the inside glass exploded, shooting shards of it all over our kitchen during the self-cleaning cycle. I immediately called Kitchen Aides corporate office in Michigan. She said that she could send a technician out to access the damages but didnt see that this was a product issue. Like I dont know how to properly push buttons to self clean! The technician came out the next day and said that he was only authorized to replace the glass, nothing else. He couldnt tell me why it shattered, he thought perhaps there was a bubble in the glass during manufacturing. I said I think it needs a whole new door at the very least, but more likely a new unit. I just paid $3000 for what will be a refurbished oven after one month of use. Today, I called once again to tell them that I am not satisfied with new glass, not to mention my oven is unusable in its current state and still has glass sipping out. I spoke to a woman in their safety committee department, who told me that Whirlpools warranty is replacement of broken parts, nothing more, and since only one pane of glass broke and not the door physically, they couldnt authorize a new door or new oven. Mind you, that we still dont know why it broke, was it just faulty glass or could it be a heating problem? She didnt care, only that they could only repair the glass. I asked if the glass could be overnighted since I have been without an oven for four days now. She said that she had no way of doing that, so I asked if I could speak to the parts department and she said I could not, that only techs could contact them. I asked if she could do anything for me? Could she assure me that it would be fixed within the week? No. Could she assure me that it would be fixed by Thanksgiving? No. Whirlpools policy clearly is that once you purchase their products, they have no intentions of listening to their customers complaints or concerns only to do the very minimum required.

I had purchased a hot water heater on Saturday and installed it myself. I filled the tank and waited about twenty minutes before turning the power on. I waited a couple of hours before testing the water temperature and it was cold. I checked the temperature setting and it was set at one twenty five, I went to Lowes and informed the service person and was told there was nothing they could do about it, I had to call the number on the tank for Whirlpool. I called the number and was told they could come out to check it but we would be responsible for the labor charges. I didnt understand why because it was under warranty and we had also purchased the extended warranty. I informed my wife so she could deal with Whirlpool because I was going to work. My wife called a number of times and was getting transferred from one person to another and getting no help at all. She was told by one person that it was maybe a problem with the wiring in our home or maybe the plumbing. One person told her that it was not their problem. We had to finally pay an electrician to come out to look at it and had to pay him to replace a heating element. The cost of the electrician and the part came to an extra two seventy five dollars. The only real help that we received was from Lowes managers that were willing to take the water heater back if we could get an authorization number to return the water which Whirlpool claimed they did not have any type of a number. Our 400 dollar water heater turned into an almost 700 dollar water heater. We had also purchased a refrigerator from Lowes that was the Whirlpool brand that quit working after about four months and we had to pay to have it fixed. Needless to say, we will never again purchase any Whirlpool products or recommend them to anyone. The service was very very poor and we are not happy with Whirlpool.

Our dishes always come out completely clean and without spotting. I dont like having to get down into the machine and clean out the filter/trap, so I pre-rinse everything that goes into the machine, so that might help. Regardless, this machine does an excellent job. This is the Whirlpool Gold Series bought in 2013. It has numerous settings, such as delay, varying cycles, air dry, heat dry, etc. All the features work as expected, but like most owners probably do, I leave it set on the same settings all the time. It does what I want and does it very quietly. This is a standard, under-counter, full-sized machine. The outside of the dishwasher is stainless and the inside has a plastic lining. The controls are at the top of the front door, so that leaves the front completely clean-looking. Love it.

Purchased double range ovens. Enamel is flaking off within 2 years. Whirlpool denies defect. They wont replace it. Any other folks with similar problems? What can I do to have it replaced? I remember the old ovens and how the enamel just stayed and stayed and stayed. Never a rust or flaking issue in those old time models. Any expertise on how the enameling process may be compromised in the newer manufacturing process (cutting corners or costs). Any options for a class action here if a commonly experienced occurrence? If similar experience drops comments/review below as a one liner - just state enamel defect. That way can figure out the number of folks with issues. Id like to take action if given the opportunity, and more so if this is a common occurrence. Lawyers are costly for one-off complaints, but there is power in numbers (think United Airlines).

My house was built 20 years ago, with all Whirlpool appliances; built-in microwave over the electric oven, gas cooktop, and under counter dishwasher. The oven just gave out. Everything else works fine! Let me repeat that. I have a 20 yr old Whirlpool microwave that works just fine! Well, since the oven broke, we thought, maybe its time to update all the appliances. We went to the large appliance store from which our original ones came, and were told that all microwaves are now made in China by Sharp, and are crap!! Wed be lucky to get 3 years out of one. My jaw hit the ground. I couldnt believe the appliance salesman was telling us this! In fact, the appliance repairman that diagnosed my oven to be unrepairable ($100 trip charge, thank you very much) didnt have much good to say about the newer refrigerators... They contain much less Freon and dont seem to hold up as well... So, I guess Ill just keep my old appliances going as long as possible! How can appliance manufacturers stay in business!

My 3 door fridge is roomy, well lighted and well organized. I love the fact that when I open the doors, I can see everything at a glance. The freezer section is also well organized and holds plenty. Being able to get filtered water and ice in the door is convenient. The main reason I picked Whirlpool is that it is made in the USA! I want to support American manufacturers that employ my fellow citizens.

I did not purchase the washer (Cabrio Top Load Clothes Washer) but inherited it in a home sale. Never had a non agitator. I was excited for this new washer. After a week I knew why they left it! My clothes did not seem clean; stains were still on them, when I used the delicate cycle a pair of pants went in folded and came out folded!!! I also would have to redistribute the clothes every time I had a load that was larger than five pieces, because it would stop. I would actually have to take clothes out and spin what was remaining then put those in the dryer and put the other clothes back in and spin those again. I was told I needed to use OxiClean on top of my normal detergent in order to get my clothes clean. Never again will I purchase a Whirlpool. Just bought an LG; fingers crossed.

Last year, our clothes started coming out too wrinkled. And until recently, its making a loud noise like an airplane. I called Whirlpool, and the only help they can give me is finding a company that would do service and would charge a lot.

I purchased a Cabrio Platinum 4.6 top-loading washer with model number WTW8240YW0 in January of 2013. My machine has a consistent/re-occurring problem of not rinsing the clothes well. After multiple washings, including the extra rinse, my dark clothing still come out with lint, dog hair, dirt and white residue all over them. I have already checked to see if the hot/cold hoses might have been crossed. I also checked for water pressure to see if water is exiting the machine properly. It is still under warranty, and I have scheduled for a repairman. However, I will most likely return the washer to Lowes.

We have been very satisfied with the way our dishwasher has performed over the years. It cleans the dishes well. It runs somewhat quietly. It doesnt seem to use too much detergent to get the dishes clean.

We bought the Whirlpool refrigerator from Home Depot. The ice maker does not work. We get 2 cups of ice a day. Home Depot Told us we should get 8 to 10 pounds of ice a day. We call a repair service and they said we should get 2 pounds of ice a day. Still getting 2 cups a day. Call again and now they said we should get 64 cube of ice a day. So now Home Depot has us calling Whirlpool instead of them. Now we will have another repair company coming out. Waiting to see what they have to say.Very disappointed with Whirlpool for not backing their refrigerator. And don’t buy from Home Depot. You can’t return if you buy it. And I have a warranty on it and they have a lemon law 3 repair calls for the same thing and they will take it back. Not true. I will be calling once a week for 5 years until they get me some ice. They don’t deserve a 1 star.

We've had a of Whirlpool washer and dryer for well over 8 years now. The only thing we've had done to it during that time was to give it a "tune up". That was done by a friend and only took a half hour or so. I don't know exactly what he did to it but the "tune up" didn't require any parts. In fact, when my friend was finished with his version of a tune up, it was as if it were turbo-charged and our clothes came out cleaner than ever. The washer runs quietly, as far as washers go, and the capacity, washing options, etc. are perfect for a washer that gets a ton of usage.

May 16 - July 25, 2014. Took almost nine weeks to get the replacement. Numerous service calls. Their tech said self-clean feature should never be used. In addition, I heard that the techs are only paid for one service call, no matter how many times they come. And, they cant fix this oven. It has to be replaced. Nightmare and very dangerous. Most American families cannot wait nine weeks for a new oven to be fixed/replaced.

Whirlpool Cabrio Washer WTW5000DW - I have owned at least two other washers in my life, and I just recently bought a new washer/dryer set at HHgregg. Was told they are doing away with agitator washing machines in the very near future so this is my first experience with a top load agitator-less washer. This thing is AWFUL!! First of all it took a minute to get used to the weird popping, grinding noises it makes while going through the cycle (which I might add seems to take FOREVER). The other thing I hate about it is there is no way to add the fabric softener at the start of the wash in this model unless you have a downy ball of which I have yet to find at my local dollar store or even the KROGER??? So I run back and forth trying to catch the rinse cycle to STOP the machine (wait I might add) and then add the FS manually.BUT THE ABSOLUTE WORSE THING is - my clothes come out with SPOTS that look like lint all over them, and they wont wipe off unless you have a wet rag to do it with!! AND YES - I have cleaned this washer TWICE already since January with the very expensive AFFRESH. I wear scrubs and they are solid colors, so it really shows up and I have to wipe off every pair EVERY day before I put them on then roll a lint brush down them. WHO HAS TIME FOR THIS??? This is on my SOLID colors which is easy to see, I can only imagine the GUNK that is on the rest of my laundry!!! I dont feel like my laundry is getting clean at all!! I am divorced and money is tight - I paid around $500 buck for this piece of crap. I am already seriously thinking of getting me another one - the OLD tried and true kind with an AGITATOR! And yes I am ANGRY. Can you tell??

I have owned a Whirlpool Cabrio HE WTW6400SW3 for two years and have had nothing but issues from the start. Control panel was replaced twice under warranty. Also the clothes (socks underwear) were under the tub blocking the drain. This is not covered under the warranty. I was told by the repairman that this is the usual issue. He told me they took the front loader design and just stood it up with no protection from garments and coins getting under the tub, through the under tub filter often and into the drain pump. You are kidding me? Almost $1000 for this washer and its so ill designed. I have read forums that this has been an ongoing issue for several years yet Whirlpool continues to build these. I dont vent to forums often but just now I finished removing the tub to remove 2 socks and 7 cents. Also, I had to remove the drain pump and found another 16 cents inside it. So far the pump has not been ruined but this time water is coming out from the machine so will probably be ordering another pump for it as well. The wife wants it out of the house tomorrow and not another cent spent on it. But it is only two years old. What do you do? If you are reading this because you are searching for a new washer do not purchase a Whirlpool! I have gotten nothing but grief and was put off by their customer service dept as well. I guess after fielding so many calls about the same thing they have been told to just put all the calls off as no big deal. I am sure Whirlpool is making a killing off the sales on this unit. The claims made during the sale convinced me. What a joke. Look around the internet and you will find hundreds if not thousands of the same issues.

Whirlpool Dishwasher Quiet Partner III Model #8575637, White - Purchased in 2006. As of July 2013, I can say this is the worst dishwasher we have ever owned. After normal use (once a day or less), the plastic on the front control panel began cracking in the first year, and the button covers have fallen off completely. Dishes were never completely clean (at least not as clean as other dishwashers). Dishwasher leaked out one side and needed repairs. Now it is in need of a new valve, because no water is coming into the inner cavity. Repairman says it is likely that the control board, which is getting moisture into it after losing buttons, etc., will probably need to be replaced soon as well. $300 more to spend on a repair bill. SAD (AND DANGEROUS!) THAT SO MANY APPLIANCES ARE ADDING UP IN OUR LANDFILLS. There should be a LAW requiring appliances to last a certain number of years, and to clearly state their expected life on the appliance when you purchase it. Planned Obsolescence is a common business plan these days, but there must be some control on what is allowed! (I may go ahead and repair this model just because I feel bad adding one more piece of junk to our collective global pile! Sheesh!!) And all those energy star, were so green advertisements? Well, if its soon to be sitting in a landfill, its NOT so green! I am willing to pay more to purchase appliances that will last a number of years, not need many repairs, and function as they advertise... Thank goodness I kept our very first Whirlpool refrigerator - never needing any repairs and still running like a tank out in the garage. (So I know Whirlpool, at least at one time, was able to build a quality product!)

My 4- to 5-year-old Whirlpool Cabrio 6300 began to display errors recently. F1 was the 1st error code I encountered. After giving the washer a hard shove and rocking, it began to work properly again... for a while. I noticed on some large loads that I was getting an LD Long Drain error. I could hear the pump running but with little water flow. Eventually, it would time out and give the LD error. A service tech was called and determined that the water pump was defective, although the impellers inside appeared okay and had no foreign objects to impede its spinning. After spending $225 for the service call, the LD error resurfaced about an hour after the tech left. Tonight I got the F1 error again, and once again the washer responded to a sharp rap. The replacement control board, which the F1 error code involves, is $220 plus labor. $440+ for a repair to a $600-$700 washer? Im going to dissect the main control board tomorrow and look for loose or corroded connections. I cant understand why the LD code occurs when I can hear the drain pump running... just very little comes out. Other times it empties like Niagara falls... I cant understand why it works sometimes and fails others. The pump is either on or off. It doesnt have multiple speeds as far as I know. Im not sure what to do next... probably try to re-sell the new pump that was installed to recoup some of the money I paid for a non-working Cabrio. This seems to be a very common occurrence.. Have any class action suits been mentioned? If so, please feel free to contact me.

Top load stackable Washer dryer - Model number YWET 3300XQO. I had two floods with the same washer dryer unit. The first flood occurred in April 2012 and thousands of dollars were paid to repair the home that was damaged due to this flooding. The second flooding happened in October 2012 with the same machine at the same home. This time there were other Whirlpool owners that also suffered with the same issue with the same model Whirlpool machine. Whirlpool acknowledged that they will pay out to fix the damages and the deductibles but to date they are simply playing games on paying out. This is 15 months after the first flooding happened.

We purchased Whirlpool dishwasher Model #GU3200XTXB Nov. 2011. Two weeks later they replaced the soap/rinse aid dispenser because the rinse aid was running out the bottom of the dispenser. Feb. 2012 they replaced the handle which was loose. July 2012 the panel lights werent working and that was replaced. Feb. 2014 the soap dispenser door would not open, so the dispenser was replaced again. March 2014 the soap door would not open again so the computer board was replaced & the door did open. However, it stopped again 3 days later. April 2014 the dispenser and the board were both replaced. The rinse aid dispenser did not dispense leaving the inside with moisture on everything. So yesterday the dispenser was again replaced but now the rinse aid is running out the bottom of the dispenser. Thank goodness we purchased an extended warranty for $169 or we would have spent more than $1,000 on repairs!! The warranty company refuses to acknowledge that their lemon law should apply. There are 2 of us and we use it 2/3 times weekly.

This dishwasher, compared to my old one, is very quiet but does a very poor job of cleaning. I now have to prerinse most all items. The silverware rack leaves many dirty items such as peanut butter off a knife. I probably waste more water on prerinse than what is saved by the washer.

Approximately 2 years after purchasing a Whirlpool Gold side-by-side/counter depth refrigerator, I noticed cracks on the interior walls. This was in 2011. First, I contacted the service contract people. They told me this was not covered under the policy. Next, I wrote & called the company. They told me they could send someone out to EPOXY the walls. I told them this was not at all acceptable to me and that I believe this is a defective product. I have never heard of this happening to a refrigerator. I am also quite concerned that there are toxins emitted through these cracks. After a time with no response, I wrote them again.This time, they referred me to Ms. Alicia ** at the Exec. Offices. She wrote asking me to call her. After making several calls & leaving messages to no avail, I wrote her asking that she kindly write back to inform me what the company was going to do about this defective product. I cant help thinking they did not want to commit to anything in a letter because I never heard from her or anyone else at Whirlpool. Small Claims Court cannot help as the company does not have an office in New York. I am very worried about the possible health hazard this possesses. I am very careful to completely cover all food inside the refrigerator. At this point, the cracks have increased in size and new ones have appeared. I am very upset over the lack of concern and lack of response from Whirlpool.Ive owned many Whirlpool appliances through the years and trusted the brand. This is not a cheap appliance. Consumers dont expect to spend a few thousand dollars on a product just to dump it in a year or two. Given the size of the Whirlpool Corp., anyone would think they would simply replace their defective product to keep their reputation if not for the health concern of their customers, which should be a priority. Over the past few years, I have had increased respiratory problems and so have other family members. I believe its due to the emissions from the cracks. I will have to dump this defective refrigerator before it gives me cancer! Thanks Whirlpool, great doing business with you.

I purchased a Whirlpool Cabrio in 2009. It worked so-so over the years but recently stopped completing cycles, citing false load balance errors and leaving towels and sheets sopping wet at the end of a cycle. Three repair appointments later, and still no success. I am thoroughly disgusted that such an expensive machine only lasts four years. Based on the service techs attitude toward the machine and other consumer comments, Im guessing I will have to replace it. You can guess it will not be with a Whirlpool machine!

This piece of junk just broke down not even one year after the purchase. Every singe Whirlpool washing machine has broken one way or another. This one will set the wash time for 57 minutes, and exactly 24 minutes left in the cycler, you hear this big crash and then everything stops. Another dumb thing about this piece of crap is that when the problem happens, the POS keeps the lid locked so that you cant tell what the problem is. What morons would put a lock on the lid? Its not like someones going to take a jacuzzi bath!Restarted the POS again, and exactly 24 minutes left on the wash cycle, there was another crash. Both times, exactly 24 minutes. NEVER BUY FROM WHIRLPOOL!

This unit is without a doubt the best microwave I’ve owned. It is reliable, cooks to desired doneness. It defrosts and rewarms perfectly. For the price I do not believe that there is a better performer. Would highly recommend with no reservations.

I thought the Calypso had issues until I got the Cabrio. It does not use enough water to get the clothes clean, it leaves them in a tangled mess, and no matter how carefully I load the clothes it is always off-balance making enough noise to wake the dead!

I hate the thing. The grates are way too large, they are too heavy, and the fact the high is not a true high and the other three are different temperatures. The oven is awful. It half cooks. You cannot do decent canning on the thing because you only have one burner. This is a mess from the get go. Why in the hell do companies think everything has to have a computer attached to it? Computers and heat do NOT mix for Gods sake. A simple gas stove is sufficient to cook with. Take the computerized junk off and make a normal stove.

It was a complete nightmare buying our all side by side stainless steel freezer and refrigerator. Freezer still working fine but the refrigerator started blowing hot air, all the food spoiled within 2 days as we were trying to figure out what was wrong. The store did the best to correct the problem and it seemed the Whirlpool company had no faith in their product as over the phone recommended having extended warranty. So sorry we bought this product, nothing but hassle!!!

Bought the dishwasher 3 years ago and now its not worth anything as its pump gave away. Cost to replace the pump is $200 or more so it doesnt make sense to do that since you can get a new one for $300-$400. Everyone I talk to say they are not building these as they use to and they give out in 2-3 years. I am very unhappy with this dishwasher.

Worst refrigerator (French Door Refrigerator WRF989SDAB00) ever! Even though this Technical Service Pointer was issued, it takes forever to get any satisfaction from Whirlpool. They were not pleasant to deal with when calling the Whirlpool Corporation. I had to research the problem while on the phone with their service representatives. The technician arrives and confirms that the evaporator in the fresh food section is indeed the problem but then it takes days for the parts to come in and then another appointment will be scheduled. Whirlpool does not provide good customer service. A refrigerator should last more than three years. Very disappointed and would never recommend Whirlpool to anyone.

I have been buying Whirlpool appliances most of my married life. Our most recent washing purchase is the worst machine I ever owned. I have ruined more clothes, rugs, sheets and towels, etc. than I ever have in my 45 years of doing my own laundry. In fact, I do not EVER remember a washing machine destroying any of my articles. I just pulled 2 almost new rugs out of the washer only to find they have been destroyed! I am pretty sure it is the extremely fast spin cycle that is destroying my items. I know it cant be the agitator because it doesnt move fast enough to even clean the clothes. And the stupid load sensor is absolutely worthless! It does not dispense enough water to even cover the clothes let alone clean them. Go back to the old machines that did their job without destroying anything and actually cleaned the clothes with an amount of water that I chose. I ABSOLUTELY HATE this machine.