Bought a new Cabrio, worked ok but in less than 2 yrs the bearing is bad. It will cost almost as much to repair as a new washer. Will never buy a Whirlpool product again. Would give negative rate!

We have had our range for over one year. The main problem is that the large burners are in the front and the small burners are in the back. This means that when we are using the two front burners we cannot access the rear burners safely. (What country provided the engineering design for this?) One minor problem is that we cannot get used to the burner control arrangement. The outside controls control the front burners and the inside controls control the back burners. Our old range was the right control for the back burner and the left was for the front burner. Another small problem is that there is no back to the pan drawer. So, with the drawer full if a pan move when the drawer is shut it will be scraped off the drawer and fall into the back and becomes hard to reach to remove.

Purchased over range microwave WMH31017AW-2 from Best Buy Mar. 12, 2015 and after installing it noticed code Door appeared and that there also was a dent on side. They replaced on Mar. 19 and we had the same Door code problem. Called Whirlpool and they sent out a Tucson repair tech and he ended up coming out at least six times changing 3 switches, 2 cams, 2 brackets, control board, and line filter. Still had problems and Whirlpool requested he call their tech and he did and they told him to make the same changes and he told them he already did all that and there still was a problem. Then Whirlpool told him to switch some wires on control board which did not solve anything. Then second thing they told him was to file and clean door brackets which also did not solve the problem. We called back to Whirlpool to tell them we did not want this defective microwave any longer as all these repair trips were not solving anything. They wouldnt give us a answer right then and said they would call us back 24 to 48 hrs and we are still waiting. We will never recommend Whirlpool to anyone nor ever buy from them again.

Whirlpool water heater FG1F5040T3NOV - I noticed that when I was taking a shower, my hot water wasnt working. I went downstairs and the pilot light on my water heater wasnt on. I tried to restart it. The pilot light wouldnt work or relight. I gave up and contacted a plumber. I dont feel I should have to pay for a plumber when its a product flaw!

I am writing to inform you of my dissatisfaction with the Whirlpool Duet washer and dryer I purchased in December of 2011. The model and serial numbers are YWED94HEXL0/M12602088 and WFW94HEXL2/c12350046. After using them for several months, I have found that the performance of the washer and dryer to be poor. I find the clothes do not come out very clean. I used my mother-in-law’s GE washer to compare and found that the clothes came out much cleaner in her washer. I was astonished at the difference. The white clothes, especially, were so much cleaner than in my washer in which white clothes, especially, come out looking like they have not even been washed. I am unhappy with the dryer as well, which continues to shrink my clothes a lot. I am distraught with this situation as this was a big purchase for me. I believe the quality of the washer and dryer is simply poor and I would like an exchange with a better quality set which actually cleans my clothes. I rely heavily on my washer/dryer as I have three young boys who go through a lot of clothes. Please let me know what can be done on your end. Thank you kindly.

We bought model WRS571CID*** which has an in-door ice maker that has stopped working after exactly 3 years. An excellent authorized service rep advised that the wire harness from the freezer to the door was damaged by chafing from normal opening and closing the freezer door, which has caused the ice maker wires to break, thereby disabling the ice maker. The only remedy is replacing entire the door, which would cost $1700 according to Whirlpools published repair data, which he is obligated to charge. Apparently, the wiring harness is not a replaceable part, because I suspect the labor hours needed to disassemble and reassemble the door is prohibitive. Well, a new fridge costs about the repair. I spoke to the Whirlpool company about whether they acknowledge that the design is faulty and that the door should be replaced at their expense even out of warranty, and they declined.So I advise prospective buyers to be aware of this issue and watch other reviews. There are many customer reviews on various sites complaining about this very issue. Our workaround is to put ice trays into the freezer to make ice, and while the dispenser still works, pour the ice thus made into the ice dispenser manually - until the wire control that also becomes damaged and stops working. I would not recommend buying this model.

Whirlpool Duet 2009 Model WFW9400SW02 - Worst experience ever with a new Whirlpool front Load washing machine. It broke down with error codes F28, F70, F71 13th month just after warranty and was leaking water. Bought 1 yr 153.00 Whirlpool extended warranty. Many reviews in internet have same complaint. Immediately had it repaired after waiting my 60 days to use warranty, but did not work after the door latch switch and one of 3 main circuit boards was replaced which was over $600.00. That was 2 visits. Fired them and had warranty company send different repair Co. They came twice with a cost of $840.00 and worked for 30 days and then had no power. 3rd repair company came out and wanted $350.00 to order part. I was offered $1195.00 cash or $1499.00 replacement top of line Whirlpool WFL98HEBU. Nice! But only 1 year warranty and I had to pay 200.00 shipping. I decided to take the money since I did not want to risk the break down on the new washer. The reviews on the new washer were not favorable with break down as the main complaint. 4 repairs in 1 year is lemon law on my warranty. My repairs were 4 in 45 days.

We paid extra for a 10 year warranty on purchase from Airport Appliances. On delivery I commented that the plastic material used throughout the fridge was of very flimsy material and wobbly. In the first week the crisper drawer joint cracked to our amazement and they had to send another one from Whirlpool. In the 14th month after the Whirlpool warranty had expired, we found the pantry drawer lid/cover shattered by the door which shut on it because of no reasonable leeway provided in its design.On calling the special warranty people they said they only covered the compressor and parts and nothing else. Called Whirlpool who quoted $85.00 for the lid, plus S&H and taxes. Now we have an eyesore every time we open the fridge when we see the taped up cracked three foot pantry drawer lid. We badly regret giving away a 25 year old perfectly working Whirlpool Workhorse Fridge and buy this newer model which we will have to live with for a quarter of a century. I am 75 years old now. Never a Whirlpool again!

I have a double door bottom freezer refrigerator manufactured by whirlpool. It is less than 2 years old and is an absolute piece of garbage! In less than a year the noise started, then the freezer became a refrigerator and my frozen stuff melted. I had a local technician come in and he fixed it but he indicated that the fix would not likely correct the problem. Sure enough, about 6 months later the same problem started all over again. Nowadays one is never sure where a product is manufactured. However, if Whirlpool had their products made by chimpanzees in the jungle they would be better than the pieces of trash they are now selling!

Burners always needed replacing and now do not work anymore - Whirlpool range looks nice, but very expensive to maintain. The burners constantly needed replacing, they do not heat up. I got a repair technician to look at it. He replaced the parts that the burners hook into. Now they do not heat up at all. Well, one of four barely boils water. The oven still works, oh great. The thing is only 7 years old. I have had ovens that lasted 20+ years at my dads house or 15 years at another house I lived in. With all the negative comments and the repair guy who tried to fix it, I think it is time to get the kids Easy-Bake Ovens out of the storage or buy a new range. Obviously, it will not be a Whirlpool. So many negative comments people left, my useless top burners seem mild comparatively.

I bought a Whirlpool water heater from Lowes. I had trouble with it from day 1. It never worked correctly. Their service department is terrible. All they want to do is sell you extended coverage policies on it. Every time I have it fixed, its never covered, and I have to pay again. You will be sorry if you buy a Whirlpool water heater.

My refrigerator is a side by side and its freezer compartment is small (width). Whirlpool is always my brand of choice for household appliances. I personally would not choose the side by side design again but I would choose Whirlpool.

I bought a semi automatic washing machine from Croma Store (Gurgaon) on 03/09/12 Model no A-72H* and I regret to say that the water direction changing knob (to change water flow from agitator to dryer), has broken. The machine is not even 4 months old and the water inlet is broken. How can this happen in a brand new washing machine? You claim to have durable home appliances products and your machine does not last 6 months? Can you see that the broken piece is attended to or replaced at the earliest?

I was sold a gas water heater that had my water smelly like rotten eggs in less than 6 months. I bought it in January 2016 and by June the anode rod I am told was no good. The only thing Lowes could do for me was sell me 2 anode rods, one the plumber thought was bad. I also had to hire a plumber. I was eventually told I was out of luck because the area the old anode rod was in was too damaged to come out.

Our first Whirlpool washer barely lasted 1 1/2 years. They replaced it with another one that broke within 9 months. When it worked, it was great... When it didnt, it either overflowed or did not wring clothes tightly on the second rinse.

We purchased a Whirlpool Energy Smart Electric Hot Water Heater with a 12-year warranty from Lowes on August 30, 2010. The water heater stopped working and the green light was flashing three times. We contacted Whirlpool since it was less than two years old and they were very rude to us. They told us it was the sensors and we would have to change them out. We waited while they sent the sensors to us. We installed them and it still would not work. It continued to flash three times just as before. We contacted Lowes where we purchased it and they were extremely apologetic and said they would be glad to replace it if we could get an RA number from Whirlpool, but that many others have been having a hard time dealing with Whirlpool. We contacted the rude people at Whirlpool again. They said they were not surprised that the sensors did not fix it. We asked for an RA number so we could get a replacement (after all, it did have a 12-year warranty). Now we were days later with still no hot water. Now this rude technician said it was probably the control board. I asked him if we were going to have to be without hot water until we changed every part on the unit. At this point, we just took the hot water heater out, put it on the curb, and went and purchased a different brand. Whirlpool has lost us as customers for life. If their other products are as horrible as that hot water heater, I wouldnt take any if they paid me to. They were by far the rudest and most hateful people we have ever dealt with and life is too short to be treated that way. I predict they will be out of business in no time with the garbage they are putting out.

Old stove does the job. I need a new and updated one. Need a warming drawer. Lower drawer does not close properly anymore. Paint on back panel is chipping. We are limited to range choices because of space.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

I purchased this LOVELY top loader on May 19, 2012 - the lid is broken and wont stay up. I am 4 ft. 11 inches and I need a stool to reach the clothing at the bottom. Kind of hard to hold up the lid and scoop clothes with the other hand!!! Today, I discovered it is rusting from the inside out!!! From what??? Pulled it forward to clean the floor underneath and discovered it has rusted and corroded even on to the matching dryer - white finish!??! Guilty by association! AAAHHH!!! I wish I could upload the picture! Whirlpool and LEONs warranty - they have some explaining to do.

I have never had such a horrible experience in my life as I have with Whirlpool. Refrigerator ($2,500) broke within three months, and then broke again another two months later and hasn’t worked right since. They have the most horrible customer service, parts are on back order, I’ve had to throw away hundreds of dollars worth of food because everything keeps freezing but they do not care. Ice machine has been broken for over a month for the second time. They are the worst company I’ve ever dealt with. Buyer beware. Do not buy anything from this company. Their products are the worst and they have zero customer service. Good luck if you buy something and it breaks. You might as well just buy a completely new appliance.

I Purchased 9 year warranty, Whirlpool water heater and installed it. Started having problems in the first month. It started giving a water temp too high error code, yet water was barely warm. Called Whirlpool. They had me do a bunch of diagnostic checks. Determined it was a bad control module. Sent me a new one. I installed it. Within a week or two, same problem. Called Whirlpool. This time they sent a Tech out. Everything on water heater tested normal, nothing wrong with any part. The tech finally, found a TSB that indicated that you couldnt have any re-circulating valves or systems connected to the water heater. We had one to keep hot water at the taps. So I removed the re-circulating kit and water heater worked for a few months. Then same problems, it keeps going into error. Error code indicates water temp too high, but water is barely warm to cold. Call whirlpool several times, they send out another control module and heating elements and I replace them. All work temporarily. Finally replace control module again, and it works for several months. Then back to error codes. Not always the same code. Sometimes it is water temp too high, other times it is check one of the heating elements. We have lived with it like that for about 3 years. We get hot water by resetting the water heater several times a day. Well, about 3 months ago it started tripping the circuit breaker in the electrical panel. I called Whirlpool and explained what has been going on since I bought their piece of junk. They will not do anything unless I call and pay for a service tech to come diagnose and repair the problem. They will provide the parts for the repair. I am not a certified appliance repairman, but I do handy man repair work for a living and do appliance repairs quite regularly. I am capable of doing every test that the repairman will do, but Whirlpool insists that I pay to get their defective product repaired. Then if I have problems again in a couple of months, I will have to pay a service tech again. I have friend that had this same water heater. I replaced the control module on his once. I was telling him about my woes and he told me he got fed up with all the problems and ate the cost and got a new water heater, not a Whirlpool. I am going to call Whirlpool one more time and then I am sure I am going to do what my friend did and put the money I would spend on a service tech into a new water heater. It will not be a Whirlfool.

I purchased a washer and dryer set, the Cabrio Platinum Series WTW8500BRO, about 3 years ago. I had a UL code come up a year ago and the machine was serviced and all was back to normal. Then only 9 months later it started acting up again. This time it sounds like an airplane taking off and there is a black spatter leaking from underneath, also the lid lock stopped engaging. I started to look up the error code for the lid lock and while reviewing that issue it was an easy fix, however, the noise and black spatter issue led me to tons of horrible reviews about this product. It is a bearing/tub/shaft issue that is going to cost me $500 to fix. First off I did not pay cash for this set, I rented it for 3 years and paid twice what it’s worth, around $4,000. Stupid on my part but I couldn’t afford it the other way. Weekly payments were easier. Now I am scared to fix this product because of all the reviews I’ve seen from other consumers. I haven’t had the other issues like dirty clothes, not enough water, high cycle times because they all start with a high number but after it configured the load the time shrinks, but this major issue about the bearings, they say I have to replace the entire tub assembly which is half the cost of the unit. So stupid and I cannot believe Whirlpool is getting away with this crap. Please please please inform me about any lawsuits. I will gladly participate in that. They should be held accountable for such a worthless piece of junk. Like I said I am now afraid to fix this machine because from what I’m reading, more than likely it will only last a short time.

We purchased a front loader Duet in August of 2011. It is now January 2013 and we had to have a service person come out. We did not buy the extended warranty because a washer should last longer than 1 year 5 months, but not ours! We need to have the drum replaced at $600. Are you kidding me! I will never buy another Whirlpool product.

I bought a Whirlpool dishwasher from Lowes and it has never worked properly ever since. It has been a little over a year now and it will not drain, will not wash dishes, and it stinks so bad that you cant drink out of the glasses. Its a total piece of junk. I called the manager at Lowes and explained all the problems. He said that he would see what he could do. I left three phone numbers but he never even bothered to call back. I will never buy anything from Lowes again.

Had to return my first 2019 purchase due to refrigerator freezing food and imbalanced top doors. I was unable to get straight answers from Whirlpool and so the mgr at BB gave exchange same problems except door not as off. Cheap product make/model. A class action lawsuit from 2016 has occurred and the company continues to distribute the same issues in their new make/model.

We have had a Whirlpool dishwasher for about 2.5 years and have been happy with how it cleans dishes. About a year ago we replaced our counter top and in the process had to adjust the bend in the mountain brackets that attach the dishwasher to the underside of the counter. This requires flexing the thin piece of aluminum at the perforated line. In the process, one of the brackets snapped. The other was barely still intact and broke several months later. I tried jerry-rigging them, but eventually decided to replace them and called Whirlpool customer service to ask for replacement parts.Unfortunately, Whirlpool wanted to charge me $10.50 apiece and another $9.00 for shipping and handling. These parts could not cost more than a few cents apiece. I was shocked that they would charge me $30.00 to replace these flawed parts. Never have I had such and experience with any customer service department. The three people I spoke with were all rude and unapologetic about my situation. Two blamed it on the install...Ive installed plenty of dishwashers and never had any problems in the past. Even if it was a failure on my behalf, the simple replacement of the parts for a reasonable charge would have been fine by me. I told them Id be happy to pay a few dollars and to pay the full shipping fee (which was also high, in my opinion), but they refused to meet me halfway. I can only think that this is part of their business plan...make dishwashers with sub-par parts, and then over charge for the replacement parts when they fail. Well, I re-upped my jerry-rigging efforts and have improved the engineering of the faulty part. Save my $30. But Whirlpool will never again get my business and Ill be sure to steer clients and friends away from this brand as well.

In the last two years I have purchased a new Whirlpool Duet washer and dryer with base, Whirlpool Gold refrigerator, and (less than a year) a built-in Whirlpool microwave. I have already had to replace the gaskets on the washer, which required a $65 deductible. I had to spend $65 on my service contract deductible for my dryer as they have had to order me a new motor and thermostat. My refrigerator had an appliance bulb as required installed; however, it still burns the plastic covering. I have not called on that yet. My microwave, which is less than a year old, has a small crack inside the door and part of the handle has broken off.

Most awful oven I have ever owned!! I purchased a brand new Whirlpool double oven one year ago. I was replacing a Whirlpool double oven, and all my other kitchen appliances are Whirlpool. It is model #WOD51EC0HB01. WORST DECISION EVER!!!! No more Whirlpool for me!

I purchased a Whirlpool washing machine (model: AW01D8810 S silver color) and a Whirlpool refrigerator (model: WBM329 TI) together from United Arab Emirates for Dhs 1999/- & Dhs 1199 /- respectively on 28 Jan. 2011. I sent this machine to my hometown (India) in the same packing and I used the washing machine only for three months and found a complaint. I informed this to service center in Trivandrum, Kerala. Their team came to my home and told me that warranty cannot be given as I purchased machine overseas. They added that the PCB for the machine is having complaint and they dont have stock in India. Also, the machine is no longer available in the factory. The Whirlpool company completely stopped manufacturing the abovementioned model. Again, I came to UAE and contacted GEC group of companies for the PCB part. I got a quotation for PCB Dhs 425/- but the items is ex-stock with them. The machine cost only Dhs 1999/- and if I spend Dh425/- only for PCB, and the machine is with me for the parts since one and half years. I dont know what to do. If I spend another Dhs 600 + this PCB cost then Id rather go for another new branded washing machine. The model of machine is AWO1D8810S and serial no. is 12 nc 859247463000 003. Please advise what to do or if I can find the PCB in Kerala. What will be the cost? I am ready to pay the money for PCB but not for the above rates. Please advise, sir.

I bought a Whirlpool washer (model wtw57esvw1) about 17 months ago. In that time, the same part has gone out three times. It happens every 5 to 6 months. The part runs 97 dollars plus labor. In the mean time, I am without the use of my washer. They say they are sorry, but they only cover their product for one year. After that, you have to buy their extended warranty so you can get it fixed by them. I feel that if I pay that much for a product I should expect at least 3 years without having to repair every 6 months! I have no washer. I am giving one star only because I have to.

Purchased a Whirlpool Cabrio 4 years ago. It worked fine until last October when I had to call a Repair Service as all the Digital Controls would not work. It was the Digital Board had to be replaced at a cost of $ 315.00. That was October 2016 and in October of this year 2017 it started doing the same thing again. I call the Repair Service and they told me not to waste any more money on this machine as it is a piece of junk. I guess he was right as when I read all the bad reviews it got today, I realize I will be better off to buy another machine. It will not be a Whirlpool product. I purchased a Sears Kenmore Washer & Dryer back in 1995 and the washer lasted 20 years and I still have the dryer. This is what you refer to as a good product.

Spent the extra money to have a beautiful, slide-in oven. The AquaLift technology just seemed like another plus. After the turkey cooked, just seemed like another oven to clean. The AQUALIFT does not work, except for the bottom of the oven!! A fresh oven cleaner? Only available only. Get this beautiful range, not AQUALIFT TECHNOLOGY. CLEANING with it.

This is our second Cabrio w10550273a. The first one was just as bad as this one. It was replaced under an extended warranty we bought. This washer just like the last one constantly gives a UL code. Thought the washer and load are level.

Im with the rest of the people on here... The only mistake I made was not checking the reviews before purchasing a Whirlpool product. My washing machine is horrible... I dont recommend anyone purchase any Whirlpool products. Its cheap and has already stopped working twice in the last 6 months... I have had a repair man come out twice to replace the door locking mechanism... Not to mention the buttons dont work, they just slide back into the machine... Plus, you have to jump through hoops just to get the machine started the way you like it... If you make a mistake, there goes your whole ** load of laundry, not to mention the water wasted. Hell with Whirlpool - Dont ever buy a whirlpool product as long as you live.

It has plenty of room. The compartments within the refrigerator are well organized. There is plenty of room in the freezer. Have had this for about eight years and going strong.

Im very frustrated. I bought a Whirlpool Refrigerator for nearly $1300 in Sept. 11. It is a side-by-side Model #ED5KVEXVL00. The refrigerator side started warming up to the point that we noticed. We put a thermometer inside to confirm; it went up to nearly 60 degrees. We tried cleaning any dust underneath from the coils and even unplugged it for a while. The compressor appears to be the potential problem. Sears is not sending a repair guy for 2 WEEKS (It is a hot July here in NY)!!!!We are saddened that Whirlpool says it is out of the one-year warranty - so now we are facing the choice of a large repair bill or buying a new refrigerator. What a waste of money... Its not even 2 years and it needs service or a dumpster. Shame on Whirlpool for not standing up for customers when clearly there is something wrong with this machine so close to the warranty and so new. Sears and Whirlpool - youve lost me as a future appliance customer!!! :(

I bought 40 gallon gas water heater in June 2004 and had to have it worked on twice, costing more than I paid for it. I am replacing it now because pilot light will not stay on, and it is currently out of warranty, and I have no faith that simple repair will hold more than 1 year stint. Customer service was attentive but product itself failed to meet expectations.

I purchased a Whirlpool washer in 2005. After the extended warranty expired, our washer broke. The Whirlpool manufacturer did not have parts in stock. It’s on backorder, so what does that tell you? So we have had to wait for over a month for the repair shop to receive parts from Whirlpool’s manufacturer. Service is very slow and the quality of product is very poor. After five weeks and no repair parts, we are going to have to purchase a new washer since we do not have our washing machine repaired yet. I promise to never purchase a Whirlpool product again.

Yesterday morning I was in my bedroom when I heard a bang... I went in to the kitchen and looked around and couldnt see anything. Then I saw my cat sitting on the floor and looking up at the microwave... It was then I noticed that the glass on the front was all crazed and making a tinkling sound. Several pieces had fallen on the stove top underneath. I had to call the repair man who said he had never heard of this before. He had to remove the door. I could not use my stove with the danger of glass falling in to food. He had to order a new door and I had to spend $65 then. When he puts the door in, it will be another $200 or more.

After 2-1/2 years we started having trouble with the spin cycle on our Maytag washer. We live in an area with no repairman. Whirlpool want us to pay just to talk to us. Now the timings off. It will not spin out.

Whirlpool Refrigerator Freezer WRF560SEYB01. Purchased the Whirlpool Refrigerator Freezer in 2012 at Sears. Ran okay for 2 years. Bottom freezer door came off the track. Called Sears. Sent out repairman for $200 to replace the door. He did not check the ice buildup on back of freezer. Next problem, severe ice buildup, loud noise. Used hair dryer to melt ice and took the blower fan out of freezer. Solid ice on all the blowing fans and found a chunk of solid ice. Freezer no longer made the noise until the ice built up again. Now, it continues to build up and we have to use the hair dryer every two weeks. A refrigerator should last at least 10 years. This model doesnt even warrant a rating of any kind.

My range was made after this date and needs this Service Bulletin part. Whirlpool refuses to ship at no cost. I have spent money on this already to discover they knew the issue in April 2004 yet sold the range in October 2005. Rena in service stated she is the highest authority at Whirlpool anyone can talk to!

I purchased a Household refrigerator Model WRF535SMBM00 on November 2013 at Home Depot which was not used but until June 2014. Awaiting finishing details on new house closing. The first year in use, I started having problems with freezer frosting, light not working, seemed like the ice produced in it, burned the light bulb. Prior to that sometimes it worked, sometimes it didnt. I started to think that it had burned, changed the light bulb. It didnt worked. After 2 months, all of a sudden the light worked, but the ice maker stopped working. What would be the suggestion to fix it, may I asked. This is very disappointing. You have a new house, and new appliances and they just dont work. And we are expected to pay for the repair! I dont think so.

Purchased a double wall oven and had it for 13 months. Used it this past Christmas and for the first time used the self cleaning mode. After an hour the power went out and now the oven is dead. Whirlpool service sent me to a local repair company and they want $70 to come out and look at the oven. This seems like a huge problem based on all of the feedback on the web. This is an obvious lemon and Im going to talk all over social media about the poor quality of this product.

I purchased a Whirlpool High Efficiency washer and dryer (Model WED4900XWO) from Lowes in March 2013. This washer has performed miserably. I dread each day when I have to use it. The groaning sound is annoying. My husband and I try to leave the house when the washer is being used. We have tried all cycles and combinations of cleaning detergents to get clothes to come out clean. On a regular basis white clothes will come out with spots or discolored to the point the clothes have to be thrown in trash. This is the worst washing machine I have ever used. I will never buy another Whirlpool product.

The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

I really enjoy the self cleaning option on this unit. It really cleans everything without chemicals and then you just vacuum up the dust. My dislike is the ceramic top though. The top scratches really easily and hard to clean up spills during cooking. Overall I would give this stove a b rating.

We bought our Terrorpool Whirlpool refrigerator in 2006. We have had problems with the ice dispenser, bad motor replacement, and now we have cracks all down the right inside wall. I had bought an extended warranty of four years at the time of purchase which covered the cost of the previous problems. But it has now expired, and I was told it would be my expense for repair. What happened to reliable appliances that our parents and grandparents had? What happened to the name Whirlpool? I will never buy a Whirlpool product again, not to mention the customer service (which I wont mention). If you have model # ED5PHEXRQ00, please write about any problems you have had and help someone else not make the same mistake.

Bought a Whirlpool dishwasher approx. 3 years ago from Home Depot and it just quit working. Troubleshooting did nothing. Called Whirlpool to make sure there was no recalls on it. I have owned many Whirlpool appliances and bought this last one because of past good experience. Turns out, after $300 plus repair, it was the control panel. The repairman said, This should not have happened, it is like new. I asked him if he thought it was a lemon? He just looked down, it happens. I am so disappointed in the quality of Whirlpool. I no longer can just buy their products with confidence.

We purchased a water heater at Lowes. Our old water heater had an issue but we always had good water pressure with the hot water until we made the horrendous mistake to purchase at LOWES - the worst possible place to buy a water heater. They sent the water heater and we had to look for someone to connect the WHIRLPOOL WATER HEATER (the runaway water heater). When it was installed the water pressure at my home was so bad that only one shower can be used at a time. This never happened before with the old water heater, there was no pressure at all.We called LOWES the WORST PLACE TO BUY A WATER HEATER, they did not accept any responsibility and they sent me to the Technician that Lowes has in DENVER to fix the problem. This bad company (WHIRLPOOL) sent us a crooked technician who wanted to charge us $600 dollars to repair something other than the water heater. We did not trust this person and we called another technician who told us that the water heater is not working properly. There is no one at LOWES and NO ONE at the Whirlpool customer service who can help us with this disgraceful water heater.DONT BUY WHIRLPOOL WATER HEATERS. DONT BUY AT LOWES!!! They are crooks! They do not respond for their products. They do not want to exchange the damn water heater as HOME DEPOT would. Buy everything at HOME DEPOT! Run away from Lowes! They dont stand behind their products, they send you all the work and if you have something wrong with your purchase they will not help you.

We bought Whirlpool Frontloader Washing Machine not over 1 month ago and it started to malfunction showing Ed1 error on its display. We contacted the service center and it was taking too long to have a visit from a technician. Then the technician, who also installed the unit came and checked the unit. He called someone from corporate office or from support team to ask what is error code Ed1 and overheard over the phone that this is a known issue on the brand. The technician said it is possible that unit will be replaced or only the motor. I contacted the brand support thru Messenger and requested to have the unit replaced, because again, the unit is not over 1mo old.I was advised it is not possible as replacement of unit is only applicable when the issue happened within seven days of delivery. STUPID ISNT? Policy is something unworthy for a product that is over 30k. And again, unit started to malfunction not over a month after it was first used. I would say we pretty much took care of the unit, we only use it twice a week. Placed it where it was perfect to put. Followed every advice given to us by the technician who installed it but still, it malfunctioned a few weeks after we started to use it. I am ashamed of the brand itself, we should have chosen Panasonic or Samsung instead not a dumb brand like Whirlpool. I certainly do not recommend the brand for a washing machine unit. Frontloader is a crap.

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

Originally installed early 2007, the very expensive unit went crazy after about 14 months, with random beeping noises, and non-response to keyboard entry. Sometimes unplugging the unit worked. When unplugging no longer worked, the unit was repaired by replacing the keyboard logic boards only to fail again the same way.about a year later. It appeared the heat or steam from the cooktop below the microwave was causing the failures, so we became careful to ensure the fan was on. Last week, after boiling some water, the unit failed again, with error code F2H2, the keyboard error. Didnt Whirlpool expect the microwave to survive heat or steam from the stove/cooktop below? Overall, the unit is great when it works. Unfortunately due to the large size of the 2 cu ft unit, only an identical unit will fit. Im skeptical of replacing my broken unit with another Whirlpool Velos unless this keyboard problem has been fixed in new units. Anybody know if Whirlpool has fixed this problem?

I have had trouble with this AccuBake stove since four months after I bought it in 2011. First, the clean cycle would work intermittently then would not ignite to bake, broil warm or clean. All burners would light intermittently. Every time I had trouble, I called the service tech from Homestead Lumber, where I purchased the product from and he could never find anything wrong. Product would work fine whenever he came out. Finally, it acted up in May of this year while the product was still under warranty and while the service tech was here. The tech replaced the circuit board. One month later, Im still having trouble replacing igniter. Four days ago, Im still having trouble. This stove stinks. Right now, I wish I had my $959 back for the stove and wish Whirlpool had it stuck up their butt.

The washer has a convenient water level feature which enables conservation. The dryer also feature multiple heat/timing features, another conservation plus. Both are compact and easily loaded and unloaded. The multiple alerts at the ending of the dryer cycles are a convenience.

I purchased Whirlpool gas range with AquaLift Self Cleaning Tech exactly a year ago. DOES NOT WORK!!! The only Self that cleans will be you on your hands and knees. Still dont know what to use. Manual says do not use oven cleaner or abrasive or you void the warranty. Ok Whirlpool any suggestions? Soap and mild detergent not cutting it. You would think with all the customers complaining about this feature the bright engineers that designed this would come up with a solution.

Found a crack under a freezer rack from sidewall to back wall. This has caused the refrigerator not to operate properly. Every appliance I own is whirlpool. Bought in 2005. Also bought another in 1994 that is working fine. What surprise me is having a crack in freezer wall. Nothing Whirlpool can or will do! Was a lifetime Whirlpool CUSTOMER. GUESS WHAT? FACEBOOK I GO. 3309 FACEBOOK FRIENDS.

I purchased my Cabrio washer and dryer 4 years ago, my dryer doesnt dry completely, I have to do 2 to 3 cycles to dry. My washer has an f51 code and I have problems unlocking the lid and it takes 2 to 3 hours to wash. This is ridiculous and it causing my electric bill to spike. Is there a recall on the Cabrio?

After only 3 years using my Whirlpool front loading washing machine the inner tub is already broken. The repairman said the cost is just about the same as getting a new washer. After reading all the horrible reviews on the Whirlpool washer I WILL NOT be getting a Whirlpool. I am so disappointed in the washer and do not recommend it to anybody. Do not buy a Whirlpool appliance ever.

AquaLift Self-cleaning does not do the job as advertised. It does very little to clean the oven. Sitting-on-the-floor-in-front-of-the-oven scrubbing is what is needed to clean the oven.

I wish I had gone on this website and read the reviews before I bought my washer about two years ago. I thought the Whirlpool Cabrio was going to be a good machine because of the brand name and because it is one of the more expensive washers. Like many others have said, I am disappointed with this washer. I bought it because it has a large capacity, but mostly because it has a hand wash cycle and a deep water soak. I have found that the only cycle that actually may get clothes clean is the Bulky Items cycle, because it actually covers the clothes in water. Some of the other cycles dont even get the clothes entirely wet. And the deep water soak doesnt wash the clothes, rinse them, or spin them dry. I might as well pre-soak clothing in my laundry tub, and then put them in the machine to wash them. Prior to this machine, I had a Maytag Neptune front loader, which did alright, but it had a few problems. I am ready to go back to the inexpensive agitator machine my mother used to have, if anyone still makes them. They at least got the clothes clean, and you could soak clothing if you wanted to. Im sorry that I bought this expensive washer. I wish I had bought a relatively inexpensive, simple machine. One good thing about this machine though is that I was able to wash a sleeping bag on the Bulky Items cycle. So, I didnt have to take the sleeping bag to the laundromat. Whirlpool needs to improve this machine or go back to the drawing board and create a new one.

I purchased a Whirlpool Cabrio on October 27th, 2010. The Cabrio is always giving me the UL code, which indicates the load isnt in balance. Ive been doing laundry for 27 years. I know how to load dirty clothes into a washing machine evenly. Sometimes it will take me all day to do one load of laundry! Seven months after my purchase, my Whirlpool Cabrio washing machine started giving me the F51 error code. I called the phone number on my Lowes receipt for warranty work. Two weeks later, I finally had my washing machine running again. I was happy and thought Id only have to deal with the UL code. Boy was I wrong?!Now Im two weeks away from my warranty expiring. Im getting the F51 error code again! This washing machine is an $800 piece of junk! Hopefully, I can get the Cabrio repaired before my warranty expires in two weeks. I do a lot of laundry. We are a family of six. So, I know Im hard on washing machines but come on. Shouldnt an $800 washing machine last at least two years? Im not even a full year into owning this junky washer and Ive had two breakdowns! In my opinion, this washing machine needs to be recalled and people need a reliable replacement or refund.

We have had this washer for a little over three years. We are a family of 2 so it gets only light use. The agitator stopped working and the repair was going to be $370! The repair person suggested we contact the manufacturer but they refused to even pay a portion of the repair. Goodbye Whirlpool! And yes, it left white streaks on our clothes as well.

My Whirlpool refrigerator, a side by side refrigerator, doesnt stay cold. Now it is 60 inside and my ice is melting but temp says it is 40 in freezer. It is only little over a year old and warranty is no longer good. Hard to believe it didnt last any longer. I paid an expensive price for it. Now I have to have a repair man come and fix it.

Does clean well but I notice that even on heat drying there is still water on the inside of the door when I open it. I have loaded it up and even the glass baking pans came out sparkling. I would recommend this middle of the road priced dishwasher.

It works quite well except if you put items in the back of the top shelf of the refrigerator it will freeze them as if they were in the freezer section. I have a bottom freezer and that works quite well. And it is very quiet when running.

After Hurricane Katrina, six years ago, the gas water heater in my house had to be replaced due to the house getting flooded. For the past six years, the pilot light and/or igniter for the gas water heater has had to be replaced if not once a year, twice a year because it will not stay lit. Each time, Whirlpool would send a new igniter and/or pilot light part and would reimburse me the cost of labor to have the part(s) replaced.Now, after six years and exhausted of fighting with Whirlpool to stand behind their product and make it right, they are finally giving me an authorization to get a new gas water heater. However, now they are telling me they will not cover the cost of labor for replacing the entire water heater. My plumber will have to pull the defective water heater out of my house, take it to Lowes, pick up the new water heater and install it in my home. And Im supposed to accept their not paying for the labor of replacing their faulty water heater? I questioned this and told Whirlpool they paid for labor for the parts to be replaced for the past six years. Whirlpool then said they would pay up to $100. This is not acceptable. I was reimbursed more than $100 for the labor to replace a part that fits in a shoe box. (Multiply $100+ times 6. They paid more than $600 over the past six years.) The cost to replace an entire water heater, picking it up from the store included, will cost more than $200, if not $300! I would not have to pay anything if the Whirlpool product was not defective!I told the manager I was speaking with at Whirlpool I wanted to speak with his boss or someone who had more authority than he did. He refused. I asked him, Was he telling me no I could not speak with someone above him? He finally said he would have someone call me.I believe I should be reimbursed for the entire amount of labor to replace the water heater since the water heater is a defective product and I have to have it replaced not by my choice but out of necessity and safety. If it is defective in one area, who is to say in trying to light the pilot light, one day it will not do something worse than just not light up. What if it decides to explode? Defective is defective and I feel my family is in danger from a defective product and it should be replaced at the cost of Whirlpool not mine.

After 5 service calls for cooling problem, under extended warranty, refrigerator was replaced. Had purchased 3 water filters directly from Whirlpool before problem. Could not use these filters in replacement model. In spite of that fact & filters in unopened factory package, Whirlpool would not refund the $100 purchase price because I DID NOT RETURN THEM WITHIN 90 DAYS OF PURCHASE, even though I wrote to their US president. Really unfair treatment & they could care less that I had to replace a defective product.

We purchased a Whirlpool Gold Induction range, model#WF1910H0AS0, from Lowes Home Center for ~$1700.00, about 1.5 yrs ago. One night my wife was cooking dinner on the stovetop and she heard 2 loud pops and the whole cooktop went dead. We had Bobals appliances repair look at the range and they gave us an estimate of $800.00!! to replace the module board. The repairman said the module board had shorted out and burned. Thankfully my wife wasnt electrocuted. I contacted Whirlpool customer service, they said, There isnt anything they can do. The warranty is only 1 year. I also contacted Lowes customer service. They told me the same thing as Whirlpool, nothing they can do, 1 year warranty, etc. I have the part# of the module in the stove, W10390743, serial#31811552. After an internet search, this part # had been superseded, which tells me Whirlpool knows they have a problem. These ranges need to be recalled. I plan to contact the US consumer product safety commission to initiate a recall. Please inform consumers if they have this Whirlpool induction range with this problem, to also notify the Consumer product safety commission.

I have used my new Whirlpool range (D-MGR865OES) about a dozen times and the damn thing is going to catch me on fire. I cannot reach the pans on the back burners without rubbing the knobs on the front and turning on the front INFERNO BURNERS AT MY ARM. I cant reach the matching microwave above either. The front inferno burners start on high then can be turned down. It happens every time I go near the thing. Either I inadvertently turn on the fire or just the gas a little and dont realize it until I smell the strong odor of natural gas. Tons of other problems, but this is the worst of all. I called the manufacturer and they call it Buyers remorse and wont give me a credit back. Tim at Freds Appliance just never returns my calls for a manager to call me. I WANT A DIFFERENT RANGE. Buyers remorse? You betcha!!! Never Freds Appliance or Whirlpool again. IF I GET BURNED I WILL PROVE IT IS DANGEROUS IN A CIVIL LAWSUIT. The manufacturer stated on 5/6/16 that there is nothing wrong with the design of this range. I do believe that the other comments are true and my salesman Tim at Freds Appliance lied when he said that the star score was not for the model I was purchasing. They will say anything to get your money and then disregard any further communication. I bought a full house of appliances at Freds Appliance. They know I wont be buying again for 10 years. How do they stay in business?

I purchased a high dollar built in side by side fridge with custom panels in 4/2005 and had my first service call in 5/2005. Since 2005 we have had 11 service call mostly for defrost failures and over temp. readings. From 2011-11/20/2013 we were issue free then the fridge over temp alarm sounded and we could not hear the fan motor. We had the certified tech come out to evaluate and found that the main control board needed to be replaced. Kitchen Aid/Whirlpool no longer make this item and forwarded us to Core Centric solutions to have a new one built. After speaking with the certified tech who had been out to service our fridge 11 times he informed us that these boards in his experience have never lasted more than a year. We spoke with a customer service rep a Kitchen Aid and asked about a prorated discount on a new built in fridge and she said it seemed reasonable but after checking for authorization informed me I needed to have the board rebuilt at my own cost and that even though this typically takes about 4 weeks to build the fact that our family would be without a fridge is not Kitchen Aids problem. 6/20/2005-over temp/not cooling call (replaced defrost thermostat) 9/2005-over temp/freezer iced over in bottom (freezer decided and drain unclogged) 10/05-over temp/not cooling (replaced fan motor) 9/06-over temp/freezer iced over in bottom (drain line decided, kitchen aid had no advice on how to fix) 10/06-over temp/not cooling, ice build up (whirlpool recommended replace heat kit and bimetal) 11/7-over temp and ice buildup in freezer with leakage (adj to drain pump and defrost drain basin made) 11/07- over temp and freezer icing over (whirlpool sent out a new heater probe) 6/08-over temp and ice buildup (bimetal and foam block replaced) 10/09-over temp, lights and motor shutting on and off (replaced defective board) 10/09- fan making excessive noise (ice buildup found on evaporator fan)11/13-over temp ice buildup in freezer, burning smell from fridge and no air movement or cooling in either compartment (need board rebuilt as on 10/09)Board no longer available from whirlpool, must be custom built at owners expense and will take up to 4 weeks. D/t continuing issues and whirlpool not willing to help the customer with replacement I would highly suggest no one buy a Kitchen Aid fridge.

Ive had a Whirlpool range for not even a year yet and the thing is on its third repair! First, the motherboard goes out twice. Then, a month after the second motherboard replacement, the broiler drawer handles melts off! ABT has been good at repairing it but seriously, I got the appliance last May! Now, Ive been waiting two months for some insulation piece on the handle. I think this product is a lemon and I am highly disappointed in this brand. I had called Whirlpool regarding this and they said their technicians would have to inspect the product and repair it. I trust them less to repair the stove than ABT!

Purchased a Whirlpool double oven (WGE745COFH) in September 2018. It is now May 2019. After 5 service technicians verified the erratic temperature fluctuations in the ovens, Whirlpool insists that a +25 degree to -25 degree fluctuation in a heating cycle is normal. The motherboard was changed 3 times, and the sensors were changed 3 times, including hard-wiring the last set of sensors. I called Whirlpool and customer service says that is normal. Ever tried baking at a 350 degree setting that fluctuates from 375 degrees down to 312 degrees while trying to maintain a 350 degree setting? I understand there has to be some fluctuation, but either it took a lot of extra time or burned my food consistently. Ridiculous.So, with the help of wonderful people at Lowes (where I purchased the double oven) Whirlpool is refunding my money and Lowes has taken back the slide-in double oven. In my quest to replace it, multiple appliance sellers have told me that all the new ovens having motherboards and sensors have big fluctuations in the oven heating cycles. I find that unacceptable. My husband and other family members have worked daily in an industry where temperatures were critical. They used ovens that could maintain temperature within 5 degrees of set temperature with analog controls. The home consumers are being ripped off with cheap, sub-standard parts making throw away appliances and getting away with it. What do I buy? Havent figured that out yet, but have purchased a countertop toaster oven that bakes beautifully.

We purchased the Whirlpool Duet (front loader) washer and dryer in 2005 from Best Buy. We had many problems with the washer leaking around the front door. After several visits, Best Buy (in 2007) said we could pick out a new washer. We picked out the Whirlpool Cabrio. About 2 years later the mother board had to be replaced on the Cabrio. We are constantly getting F codes and have to unplug the washer several times for it to reset. It also sounds like a plane getting ready to take off and from what I read that repair is very costly. It has been leaking as well. I contacted Whirlpool today and they informed me that there was no recall on the machine and when I told them that there were many complaints for the same issues online, they said they do not base their recalls on blogs and to fix the problem, I would have to incur the cost. This machine is the biggest piece of junk that I have ever owned. I will be sure not purchase a Whirlpool in the future!

Worst customer service I have ever seen. I have been waiting on a part for my dishwasher since before Thanksgiving. I have sat on hold for 2 or more hours. They cannot connect you to a supervisor, you just continue to wait on hold. They cannot give an eta for the part that has supposedly been in production since before Thanksgiving. I get told one thing, then when I call back for an update 2 weeks later that person has no idea what Im talking about. I will tell you one thing, if you do not want a headache, I suggest you buy another product!! I can guarantee, I will let everyone I know and never purchase Whirlpool again if this is not resolved this week! After doing my research, this part should be recalled. It is a big issue with this very expensive dishwasher.

Whatever you do, dont ever buy a Whirlpool French door refrigerator. For the last 5 months this $2,200 error in our judgement has not worked. We purchased it late last September and were so excited to enjoy this sleek machine. Wrong. In November a controller broke and the refrigerator portion froze over freezing everything and blowing apart the deli drawer. Then the ice maker was not working, it topped out at about 10 cubes a day. After that it acquired the lovely habit of shutting off every several minutes. 24 hours a day. Every time it would turn back on it would chime. 24 hours a day. And neither the refrigerator nor freezer portion would maintain temperature. Whirlpool keeps sending people out, turning us into their Guinea Pig while they try to come up with a solution. The chiming has finally stopped but we still dont have an ice maker and the light is intermittent. Another repair man is due tomorrow. So unless you have countless hours to spend waiting for and dealing with repairmen, making phone calls and enjoying throwing away spoiled food, dont waste your money with this company.

The refrigerator has excellent quality, low noise level, clean lines and enough room for produce and frozen foods. Would recommend this to friends. This replaces a Whirlpool refrigerator that was over 30 years old. The original unit still works extremely well and we gave it to a family that needed a refrigerator and they were very happy to receive it. It looked as new as the day I purchased it 30 years ago.

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

I purchased a Whirlpool cabrio mod. wtw5840bwo washing machine in Oct. of 2014. As of June 2015 I am ready to kick it to the curb. The washer works to it design and hasnt broke down but it doesnt clean our clothes. We load the machine, add the right amount of clothes and recommended detergents and 1hr later after the wash cycle is completed, the clothes still stink with the smell of daily perspiration. I went back to using our old washer that has a worn out agitator. It does a better job.

AquaLift cleaning system does not work. My oven was barely dirty and I had to scrub with the special sponge to remove baked on food after I did the cleaning system twice! Rust is also showing up on the drawer which they refuse to repair because it is ONLY COSMETIC! Stove is 16 months old.

After 48 years of marriage, I had never had a new, matching washer/dryer set. I had had several new washers, but only used dryers. These all were very good units and served me well for years. So I was excited to buy a new, matching set. I have never been soooo dissatisfied with anything in my life. As I have read from other reviews, the washer uses very little water, sometimes hardly enough to get the load of clothes wet, very little soap, and in my opinion, does hardly any agitating. I dont feel my clothes have ever appeared clean. The only ones that look clean were the ones that started out looking clean when I put them in. I know this is all an ecology thing, water saving, government guidelines, etc., but please give me my old washer back. It did enough agitation to get clothes clean. And the dryer usually will not get the jeans dry on the first attempt. I have tried various settings, and they just dont get dry. In short, I HATE THIS WASHER/DRYER SET. I have heard others talk about the same thing. No one likes them, but we are stuck with them. Would like to have the government step in and see how dissatisfied everyone is with them and force Whirlpool to give us our money back, trash these units, and buy something that actually works. PLEASE, IF YOU ARE LOOKING FOR WASHERS AND DRYERS, DONT BUY THESE. I believe they are called Cabrio.

Water heater was defective from the factory with a pinched wire between the thermostats. After replacing everything on the heater Whirlpool would not reimburse any parts or labor for the unit... Whirlpool is dead to me now, and forever and I love to tell my story to prospective buyers of their products!!! So far, to date I have cost them about 14 sales of major appliances (and still counting!!!). After reading some reviews… Im (sorry, I omitted the personal insults) in respect of your review guidelines.

We purchased the model WFC7500VW, 24” washer and accompanying dryer in June of 2015. Within a couple of months, the water pump went; also we continually had to take the front panel off and clean out the filter when we get an A11 code! Now we experienced an F06 code... This code means the washer can’t go into high speed. The repairman (Whirlpool recommended), told us that a new tachometer motor, etc would run $500-$800 with labor! He also said that the noise the drum made was bad. My dryer works fine (only complaint is the grinding noise it makes, which Whirlpool told me is normal)... I would like to purchase a new washer, but don’t know what will fit under the dryer. I do not want ANY Whirlpool product!

We were looking for stainless steel and this model was that. This model has lots of presets which we like. We lucked out and got it on sale and were able to get features of a more expensive model for a lesser price. The only downside is getting the turntable back in when you clean it. One of the things I wish it had was a way use the timer for foods cooking in the microwave plus use the timer separately for timing food you arent cooking in the microwave, but will be part of the meal. Also, the defrost options could be clearer!

We purchased this combo from Lowes; checked my account and saw we were double charged! Got the charge adjusted; jeez. Bought this size to do comforters and large loads, but nothing large gets completely wet. Our clothes started to mildew as Affresh does not work. Im allergic to mildew and got headaches. The mechanic said this mildew is because all the action is under the basin and you dont want to see how black it is under there. It began to leak as buildup went into the bleach dispenser, and it turned black.He said to run a gallon of white vinegar in the clean cycle once a month, and this did work. I did a clean out with Castile peppermint soap, several white vinegar treatments, and got rid of the mildew and the (clog related) leak. I now use Mollys Suds powder. I was shocked to read on the Mollys site that mfg does not have to list all the terrible ingredients in commercial detergent, which is not helping you or the machine.

We have had this Whirlpool washer duet 5 years. It regularly rips shirts, underwear, socks, and sweatshirts. Jeans or heavy denim are safe but polos, hanes, or flannel are not. We have been putting our clothes into laundry bags and lingerie bags for a couple of years now to wash safely. Additionally it leaks out the front door. We clean it regularly and it still has mold growing on the rubber gasket - we do prop the door open also. All in all it is a terrible dryer. My previous Maytag was fabulous. I will never buy a Whirlpool again!

I went to get ice from my Whirlpool Gold refrigerator, model GB2FHDXWS, and found it was melted. Light and fans were working. I had to throw out all that was in the freezer drawer. I called Lowes service and reported that our four-month old refrigerator wasnt working. They sent a food claim number and set up a service call. Then, the lady said to unplug it and plug it back in. We had since cleaned it out. I unplugged it and plugged after a minute and it came back on. The Ace service guy called to confirm his schedule. After hearing that it is running again, he said they are computer controlled and unplugging it and plugging it back in reboots it, as you might reboot locked up PC. He also said that since it is now running, Whirlpool wont stand behind a service call. He said wait until it does it again. Now thats just jim-dandy. We have an expensive new Whirlpool Gold refrigerator that has computer controlling that cant be trusted as the control may or may not lock up in the future spoiling the stored food.

I had the first microwave for 6 years. My husband messed it up so got a new one, same over the stove type. It has lots of programs. Its a rather large microwave, plus it has a steamer which cooks vegetables with steam while I am doing the rest of the meal and whats more important is its quiet. The site is fantastic not just in width but in depth. The best thing about this microwave too is that it has a frozen cycle which does not partially cook the food like most microwaves and the defrost is the same, it does not partially cook it actually defrosts completely without cooking it. This is by far the best microwave I have ever had, and I wouldnt want any other brand. It might cost a little more than the usual brands but its worth it. I also have a mini Whirlpool on my Countertop for my grandchild to use so he keeps away from stovetop at all times.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

Does not clean clothes as well as I was told it would. Very dissatisfied with the price and performance and would not recommend this brand to family members as well as friends. With the way the current economy is, companies like Whirlpool should reduce their prices!

Water began accumulating on the floor, dripping out of the freezer 16 months from installation. Upon investigating I found the bottom of the freezer had a solid sheet of ice on it. Water was dripping out from the back of the freezer and collecting until it froze. I followed a YouTube video that explained the problem, the freezer drain clogs. The video continued with a how-to dismantle the freezer to defrost the drain and drain the water. Apparently the drain is too small and the fix is a new grommet which costs approximately $27.00. I followed the YouTube video and TEMPORARILY fixed the trouble myself. This is a Whirlpool defect, aka, poor design. What is Whirlpool offering to customers to permanently solve this problem at no cost?

My Duet washer is just 3 years old and has had light use as there are only two people in the household. After just 3 short years the machine stopped working. We were told it needed a controller board and new valves. The cost of the repair was quoted at $733.00. This is far more than we paid for the machine. So we called customer service and at first they thought they could sell us a plan for $350.00 that would cover the repair but it was denied by the supervisor. So zero help, absolutely nothing. Now the backdrop here is that our last Whirlpool (same type) is still in use with our son no repairs in 15 years. Does anyone reading this think we should buy another Whirlpool or recommend it to our Friends and family? I think a Maytag is in our future. Whatever happened to companies standing behind their reputation in America?

I purchased a Whirlpool brand refrigerator from PC Richards two months ago. The compressor has stopped working causing my refrigerator to stop cooling and in turn all my food has gone bad. I reached out to P.C. Richards and they immediately credited me a check for the full amount of the refrigerator, with the option to get a new one delivered to me. I asked P.C.R. customer service if I would be credited for the food in my fridge and they suggested I reach out to the manufacturer. I reached out and, to my dissatisfaction Whirlpool will not credit me for the loss of the food in the refrigerator. I am completely disappointed. As I mentioned before I purchased the fridge 2 months ago. This is clearly a manufacture issue. I purchased a lemon and I am getting no support from Whirlpool customer affairs department. As a person who works for a reputable company in the purchasing department, I will see to it that we never do business with this company again. A company that doesn’t stand for anything or even compensates their customer for a faulty product should not be in business. Forgot to mention the customer affairs rep. Offered me fifty dollars for my troubles. Which I turned down. Besides the fact that fifty dollars will not cover a third of the items in my fridge, money is no longer the problem. It is the lack of customer service for purchasing one of their appliances. I am completely disappointed and will never recommend or purchase this product again.

I purchased a top load Whirlpool Washer and Dryer in April 2021. When it was installed I commented about how noisy it was. I was told it was because it was empty, but it will be much quieter once you put in a load of laundry. That did not make any difference. I called Whirlpool customer service and explained I had just purchased it less than a week ago and it appeared to be very noisy. I was told they could send someone out, but if they determined there was not a problem I would be charged a service call. I said the machine is not even a week old why would I be charged a service call shouldnt this be a warranty issue. Again I was told there would be a service call charge.I am completely baffled at the customer service response. This is the first and only time I called. I contacted the store where I purchased both the washer and dryer and was told it should not be that loud, this is the first time anyone has complained about the noise level and there should not be charge. Whirlpool has terrible customer service and I will NEVER purchase another Whirlpool product again because of the customer service. I have purchased numerous appliances in my lifetime and have never been treated so poorly. If I could return both the washer and dryer I would not hesitate. I would not recommend Whirlpool to anyone.

The Whirlpool washing machine came with our apartment. It is a top loader, which I like. The only difficulty is that no matter what I clean the interior with, I cannot seem to get it clean. It gets very dingy, even with HE detergents.

I bought this Cabrio Washing Machine just over a year ago and it never drained water when I was doing towels and bed sheets. Life got in the way, and I managed to run smaller loads in the regular settings. Now, the machine is just over a year old and it will not spin unless I put it on the rinse and spin issue. It takes well over 2 hours to wash a load of laundry. From looking at other reviews, this is a big problem. I would not recommend this washer to anyone. It cost a ton of money and was the worst washing machine I have ever used.

I purchased Whirlpool only front load compact washer in June 2015 and lasted only a year before the door lock broke and getting F6 error that means mother board to be replaced. Whirlpool warranty department (AIG) did not bother to do a complete repair and offer buy out at a 75% of my purchase price. My five year warranty premium cost was not refunded. I do not recommend this model be purchased by anyone. Whirlpool washes its hands on the quality and reliability of its product in US and that is a shame! A service life the unit should be at least 9 years with affordable maintenance cost.

I am experiencing problems with keeping my pilot lit too. I checked the screen and this is not the issue. I have just returned from Lowes where I purchased the water heater and they informed me Whirlpool supplied kits for this issue and it was widespread. They mentioned a class action and went on to tell me they and all surrounding Lowes stores are out of the free kit and arent expecting anymore. Am I to feel lucky my water heater water didnt fail sooner only to feel unlucky all of the free repair kits are now gone? Lowes provided me with the Whirlpool phone number for help and they have just informed me it will cost me $35.44 plus shipping. I now see how widespread this problem is. This isnt right. I am very disappointed in the handling of this known problem! What is my next course of action?