I have had this product now for 1.5 years and am very dissatisfied with it. Whirlpool calls their oven an Aqua Lift Self Clean, which is terribly misleading. There is nothing self-cleaning about it, except that the person who needs to clean it is me (myself)! I cannot use oven cleaners on it, because that will void my warranty, so the only way to clean it is to scrub, scrub, scrub, down on my hands and knees, which I havent had to do for many a year. My second issue is with the glass stovetop. I have had many glass tops before and have never, never had such trouble cleaning it. Every time I use the stovetop I need to scrub and polish vehemently to clean it. And thirdly, the dials fail very quickly, and to replace them costs me $50.00 a pop! In just 1.5 years two dials have failed. This is just unacceptable, and I say shame on Whirlpool, and shame on the company that sold it to me. I will never, ever purchase another Whirlpool appliance again.

We purchased a new bottom freezer Whirlpool refrigerator 4 years ago. For the past year we have had problems with the freezer frosting up. An appliance repairman told us the seal needed replacing. This was done with no success. He states there is nothing he can do for it. The refrigerator runs all the time and the freezer is unusable.

I had a Whirlpool washer for three years that I bought at Sears and it started making a noise. I called Sears repair and they said it was the bearings. Would cost 600.00 dollars. The machine is still running making a noise are there more in a machine. I will never buy a Whirlpool product. I just lost my husband and I cannot find the bill but I am calling Sears tomorrow.

The ice maker only makes enough ice for two small glasses. I wish Whirlpool would buy it back and let me buy a new side-by-side. I have to buy bags of ice because of this. I truly am very unhappy with this Whirlpool with the freezer at the bottom. For what I paid for it, this refrigerator is not worth the money. The model is G165DRXY07.

Purchased the Whirlpool DU915 in 2004. Its been 16 years and I havent made a single repair. A lot of that is just proper use, i.e. scraping off food stuff, using correct soap, etc. I have other newer Whirlpool dishwashers at rental properties which have required repair due to misuse. I would recommend Whirlpool products to friends and family.

We bought our washer, dryer, stove, microwave, and dishwasher in September of 2010. In 3 years we have had to replace our Whirlpool over the stove venting microwave, have spent over $550.00 on repairs on the Whirlpool refrigerator, and now have to replace our Whirlpool Cabrio washer. This of course does not include our time, effort & frustrations, especially with Whirlpool customer service. Will NEVER buy Whirlpool again. Were all for a class action lawsuit.

I bought a 5 burner Whirlpool range that I really like except the danger of knobs turning on too easily and releasing gas. You just have to brush up against them lightly and they turn. 3 times my nephew has come into a gas smelling kitchen. Whirlpool sent repairman out. He said they operate properly. Really?? What to do?? Does someone have to die?

I bought my house in 2009, and the previous owner bought this refrigerator in 2005. By 2012 The light and temperature read out went out. A circuit board had to be replaced. I have a home service company that I pay for yearly which takes care of the appliances. As usual, the fine print on the back of the contract said circuit boards were not covered. When I went online to purchase the part, the cheapest I could find it was $180. My service company said they would not cover it because they break down so frequently, with Whirlpool as the biggest offender. They gave me a discount and charged me $125 for the replacement. Whirlpool is making a fortune on these defective parts, which last long enough during the warranty period, and then you are on your own.In 2015, after the refrigerator was 10 years old, the compressor died. Hundreds of dollars of food spoiled. My service company said I was covered for the replacement, but I would have to wait 5-7 days for the part to come in. I was so furious that a refrigerator of this age would break down on me. The repairman told me he has seen these Whirlpools break down after 5 years. He said they are junk. When I was young, we moved into a new 20 story building in 1963. All the apartments had the same refrigerator made by Frigidaire. I lived there for 26 years. When I moved out in 1989, that refrigerator was still there working perfectly. It never needed a repair. I never heard anyone complain about theirs either. How is it that in 1963 a company could build a workhorse of a refrigerator, but in 2005, Whirlpool, a company in business since about 1911 makes this junk? I will never buy a Whirlpool product, and will tell the world not to do so as well.

Whirlpool has been an absolute nightmare from day 1. We bought a brand new 50-gallon water heater from Lowes. It did not work. We went back to Lowes and were told to contact whirlpool. We contacted Whirlpool and were told to conduct a number of test and all test passed, so they said we needed a plumber to come look at it. Remind you that this water heater is brand new and has not worked since day 1. They said the plumber would cost $130 and they would pay for parts. Why am I having to pay when my water heater has never worked. Paid the money. Had them come. They replaced a part, did not work, replaced another and it did not work, so the plumber requested a new water heater. Whirlpool refused. What is the point of paying and they are not going to fix it.Whirlpool insisted it was our ventilation even though all test proved that was not the problem. So out of pocket again to fix the ventilation and it did not work. After 2 months of no hot water with a two-year old at home we had someone we know come look at it and fixed the main pipe. Whirlpool took my money and didnt fix my problem. HORRIBLE SERVICE.

I just wanted to post a quick response to a problem that so many people are having with their Whirlpool FG1H5040T3NOV Hot Water Heater. The biggest problem is the Pilot Light Wont Stay Lit. Ive had this water heater for many years now (since 2005) and two days ago we didnt have any hot water. I checked the heater and found that the pilot light was out and that when I lit the pilot light with the igniter, it wouldnt stay light. This could have been a number of problems causing this issue but heres what I did to get it fixed. I looked around on the internet and saw that many people had this same problem and several years ago Whirlpool gave out warranty replacement upgrade kits to fix it. I called Whirlpool support, gave them my serial number and mentioned the upgraded kit. Unfortunately, my 9-year warranty expired a few months ago and I am no longer able to get the upgrade kit for free. Apparently this upgrade kit was part of a settlement for this water heater that was sold through Lowes. The upgrade kit has a few enhancements including an adapter to allow the use of a standard right hand threaded thermocouple as well as a larger pilot light window and added safety thermal switch. This is definitely an improvement over the old.Anyway, I looked at Lowes website for this upgrade kit and their description and internal part number is slightly different but it is the same thing as confirmed by Whirlpool. Whirlpools part number is 6910813 for the conversion kit. Lowes calls this part American Water Heater Company Gas Enhancement Kit 5040T NG. This kit is only $35 which isnt bad. So, I went to Lowes, purchased the kit. The instructions are included and are even good for a novice. It took me about an hour to complete the changeover. Youll need to remove the old burner and orifice to use them on the new kit. I then checked for gas leaks. I lit the pilot and when I turned on the heater, the burner lit right up. All is good now!

I can not find parts for 50-gallon Whirlpool hot water heater. The left hand thread thermocouple quit functioning so I have no hot water. I have called every plumbing concern in a 50-mile radius and everyone said that it was some kind of class action suit because you can not replace the part of the thermocouple and that they only make right-hand thread couple now.

Hi Folks, so today I had the pleasure to speak to Whirlpool regarding a repair bill on our washing machine which now has a bearing failure and estimate to repair was 1279.00. Its 6.5 Yrs old, just out of extended warranty and cost me with the pedestal a total of 1250.00 when new. I explained that in the 6.5 since I have lived at this house where we spend all new Whirlpool Gold Appliances, half have now failed. Range Microwave, Dishwasher and now the 1250.00 front loader is dying a slow and agonizing death with a bearing failure. Just so everyone understands, the estimate is from an official Whirlpool repair service that was booked through the Whirlpool website. Other repair folks just would not bother to look at it when I told them I believe the bearing was going bad.The repair man that arrived was professional and on time. However, I had a hard time understanding how a 6.5 Yr old washing machine would be considered beyond economical repair by costing 1279.00 to repair. Labor was 250.00 which I thought was fair. Time, etc. But parts made up the difference in cost. So later in the day, I spoke to Whirlpool and they offered the equal new washer for what would seem an excellent price. About half off. Wow, I thought that sounded good. So I asked if my existing pedestal would work with the new washer and it did not and I would have to pay for one. Regardless if my old one was fine or not.So, they offered a discounted rate from new at another half off. Total approx 800.00. So, I asked the Whirlpool rep to hold on and I need to check with my wife if she wants the replacement. She uses it as much as I do and wanted her thoughts. She checked the model on the washer and pedestal and with the local Home improvement store, they have it on sale for both units (washer and pedestal) and its about 50.00 less?Consequently, I called Whirlpool back and explained that it does not move the needle to regain my trust as compensation on a 6 yr bearing failure, failed dishwasher and range microwave they offer what a distributor of their product can offer for less as a package? Really? I mean, the Home improvement store is not in the business to lose money. Now, I am having a hard time understanding my own failure to have trust in a brand I used to have with my previous house.My mom had an old Whirlpool washing machine that lasted 25 years before she and my dad gave it away. You know, the old white top loader they used to make back in the 70s. Sheet metal, made a racket and never broke? Oh yeah got the clothes clean too! I dont know what to make of it anymore. So, I will just wait till it dies and take my hard earned money and spend it on another brand in my next house which we are going to move to soon. Maybe I can feel nostalgic and find my moms old washer. Its probably washing someones rags right now and getting them clean. It must be 35 yrs old by now.I dont expect to get anything for free. Its out of warranty, so I need to deal with the consequences, but there are steps the other party can take to help remedy the situation. I think they tried and it was genuine but in my thoughts its just not enough when your local box store is offering the same. When you develop a brand to extend a message of trust in quality and value, you need to have quality and value all the time. I suggested they help with the costs on the parts. I would certainly pay for the labor. Parts cost little to the manufacturer. Unable to help that way. I thought it was cheaper for them too. Guess not. Its come to be a throw away washing machine at 6.5 yrs and I am Infinitely disappointed. I just want my washing machine to work as well as my mothers old one and have the possibility to fix once in a while when needed.

I shouldve read the reviews online about Whirlpool before buying our washer and dryer Duet. 4 years later the main bearing is going out and its 1200 to fix it. No support from them or anything. They did offer a loyalty discount on a new washer... No thanks. Just would be another headache a few years down the road Im sure. Goodbye Whirlpool. Never buying anything from them or their other brands. Ill definitely spread the word too.

We purchased a Whirlpool AccuBake oven in 2005. I think we used the self-cleaning feature about 3 times. The reason I mention this is it may be a possible cause to the frightening experience we had on August 15, 2012. My wife was cooking on the stove top when suddenly we heard loud electrical explosions coming from the back of the oven. We soon saw long arcing bolts of sparks shooting out the back, and my wife was terrified and didnt know what to do. I told her and my son to stay away from it. I ran to the circuit breaker box and turned off the breaker. We then looked in the back of the oven and it was on fire. I ran around looking for a fire extinguisher but my son managed to put the fire out. We called Whirlpool up and explained what had happened. They immediately sent someone out to look at it.I was very impressed at how fast they got someone out there. Whirlpool sent two technicians to look at the damage. After they were done inspecting, they told my wife that the problem is loose connections on Whirlpools side and not the feed and it had a damaged control board and that this is the fault of Whirlpool. He was very polite to us and apologized for any inconvenience. After a week had passed, no one called us, so my wife called and talked to some woman representative at Whirlpool. She told my wife that the report she got said that the oven had loose connection on the feed side from where we bought the oven and we should deal with them. My wife couldnt believe her ears and said, No, thats not what the technician told us, and the woman continued to talk and my wife said, Wait, slow down. The woman replied, Oh, am I going too fast for you? Well, I guess I have to talk slower then, in a sarcastic tone. My wife then called the technician who wrote the report and explained what the representative had told her, and his reply was, I cant believe she said that. I am not happy about this, that is not what I wrote in my report. Dont worry, I will personally take care of this. Again, the technician was civil and polite. After two days passed, my wife talked to the same woman again but this time she changed her story. She never apologized and said, It looks like in this report that the connections were loose to the control board. Since the oven is 7 years old and accounting for depreciation, Whirlpool is offering to you a total of $59. My wife said, Really, $59? How long is the life expectancy of these ovens? She told her, 10 years. My wife said, 10 years? Well, ours only lasted 7 and you are giving us $59 after we were almost killed and my home could have burnt down to the ground? She said, That is our offer.I called Whirlpool back and asked to talk with the safety supervisor and it was a woman again. Was it the same woman? It could have been the same woman my wife talked to, I was not sure. I asked her, When is it appropriate to issue a recall on a product? Our oven was defective at purchase. She said, You are the only complaint we had on this oven, so no recall is necessary. Yes, I said, but since it has been proven this is the fault of Whirlpool, I would expect at least a working oven from Whirlpool. I also told her the technician told my wife that Whirlpool should be bending over backwards for you, and she said, I apologize for the technicians remarks. I told her that I was dissatisfied and she will be hearing from me in the future. I did some looking on the internet and I found that KitchenAid which is made from Whirlpool had issues with a particular oven which was found that when the self-cleaning feature was used, it would heat up the control board, and since most people dont use the self-cleaning feature that often, it would take a very long time to develop. I thought that loose connections and heat are a bad recipe for disaster, and that quality control negligence and inferior components are to blame. Considering the past history and track record of class action lawsuits and appliance malfunctions such as the control board on their dishwashers, I believe it is all connected and related to my problem. Sorry but $59 isnt going to buy me a decent toaster oven, let alone a real oven. That oven should have lasted over 10 years and considering the possible damage and deaths that could have occurred, you would think that it would be in Whirlpools best interest to address this problem and bend over backwards for anyone who had the misfortune of purchasing this mickey-moused nightmare of a disaster-waiting-to-happen problem. Its not so much the money. What if a small child touches an oven as it conducts 220 volts then shocks into a childs heart to ground? What a ticking time bomb this oven is. As far as I am concerned, I dont want a dangerous oven like this in my home and Whirlpool needs to take some lessons in public relations.

I purchased a new Whirlpool Cabrio washing machine from DeWaard & Bode at Bellingham, WA in January of 2007. The serial number is **** and the model number is ****. Several months ago, the dreaded F1 code appeared. The code initiates when the washing machine is started and must be cancelled and started 3 times to continue washing. Later, with approximately 19 minutes left in the cycle, the code reappears and requires canceling and restarting another 3 times, at times 4. I have no extended warranty so I have no coverage for repairs. I also dont want to pay for a service call for what is most likely the computer module as evidenced from the majority of complaints online. This washing machine still looks new and works other than the inconvenience of having to stand by when starting the cycle to reset the code and then having to run upstairs later to reset the machine when its partially through the cycle. At some point, it will likely quit operating all together. I have purchased several appliances over the years from DeWaard & Bode and will be replacing all kitchen appliances again next year due to a planned remodeling but at this time, I do not intend to get them locally due to this issue. I have reviewed several comments online and feel that Whirlpool has a real problem with this particular machine that they refuse to be responsible of. I was offered an extended service plan for 1 year at $132.01 or 3 years for $336.61 but Id have to wait to be allowed to utilize it due to existing circumstances. Im not sure if a fix is actually available. The local dealer did not offer any assistance.

My side-by-side refrigerator leaks water. I find water on the floor but we cant find the source. When I called Whirlpool, they stated its not under warranty, but we can schedule a repair appointment, I declined. Im still looking for the leak. Its intermittent, sometimes I dont see water for a while. The last fridge we had, we had to get rid of it because the sides and front got too hot to the touch. I was afraid it would cause a fire.

I bought a new Whirlpool fridge that has been a piece of junk since the day I bought it. The minute the warranty expired. The thing broke down. The corporate service center was a joke. 15 min wait time just to get through. Then a runaround of misinformed referral numbers. Minimum charge $200/30 min just to have a service rep even look at it. And then $100/hour + parts after that. Highway robbery. My doctor doesn’t even charge me that much. I will never buy a piece of junk WP product ever again. Their customer service is rude and non-existent. The company does not stand behind its products. Don’t buy!

I purchase the front load, energy efficient brands, low water usage. Love Whirlpool; never had a problem with their appliances. Front load, low water usage, clothes dont sit and spin in dirty water. Dryer has multiple cycles. Perfect for the whole family. My last Whirlpool set last me over ten years, wanted that same quality level in my new purchase. I wanted a quality machine. I was very familiar with the Whirlpool brand and knew that was going to be my first choice in a brand. These were full size. The tub is large enough to hold a king size comforter and wash it without destroying it. The dryer has a separate attachment for pillows and shoes (sneaker plus) and was competitively priced at the time of purchase.

Bought this washer two years ago. First experience was when a load of towels became wrapped around the agitator. Called in service tech who told me to load the bin with the cloths pressed against the bin wall away from agitator, as if the cloths/towels would stay away from agitator. Two years later, Im ready to the machine to the street. Forget sheets and bedding. The agitator wraps them so tight that I almost rip the cloths/sheets to unravel. I had to wash a pair of work pants that were soiled with mud three times and there was still a stain. I will NEVER EVER buy another Whirlpool product.

We just purchased this Whirlpool Washer. It is so awesome. Has all the many features I was looking for & we purchased it on sale. But really since using my washer I would buy it again even if it wasnt on sale. I love it. I have never been disappointed with Whirlpool. Everything I own in appliances is Whirlpool.

I purchased this Refrigerator Model #wrb322dmb, bottom freezer, 21cu ft. last year on July 3, 2015. In September I noticed rust spots on the top door. I called Home Depot where I purchased and they directed me to Whirlpool. I did purchase an extended warranty with Home Depot. Whirlpool did replace the top door. Thought that took care of it. Today one year and two weeks out of warranty, I again notice rust on both doors. Called Whirlpool. They said too bad out of warranty, not considering I had a previous report of this very same issue. So since I am very unsatisfied with this result and the fact that an expensive product is rusting, I decided to share to try to prevent someone getting stuck. Stainless steel is not supposed to rust which leads me to believe that it is not Stainless steel, but a Stainless Steel finish and not a very good one. So I am stuck with a rusting $1200.00 refrigerator only after one year. I have always purchased Whirlpool, but no more. They lost a 40-year customer. I have always bought American made but no wonder people are not buying American made any longer. TO SUM IT UP WHIRLPOOL STAINLESS STEEL APPLIANCES RUST! DO NOT BUY!

We bought our Whirlpool Refrigerator a little over three years ago. Within a few months we started having problems with the unit. From ice maker issues, cooling and freezing. Initially the frig was covered under Whirlpools 1 year warranty. Then our extended 3 year warranty kicked in through HH Gregg which they supplied for free because of their poor handling of the initial sale. We have lost track in how many times a repair man has come out to work on the refrigerator. In the last year alone its been at least 8 times. The most recent problem had been the freezer not defrosting properly to the point where we had to store food in our neighbors freezer. The repairman has tried everything he knows and is stumped. Well our extended warranty has run out but theyll continue to work on the problem as long as we report the issue within 30 days which creates a whole different set of issues. The extended warranty states they will replace the refrigerator if it has the same problem 3 times. However what they dont tell you is that if you call BEFORE 3 time period its considered a recall and that doesnt count towards the 3 strike rule. We contacted Whirlpool and they wont cover the refrigerator because the repair company isnt on their approved list. Really a Sears repairman isnt approved? So buyer beware of a lemon Whirlpool Frig! They seem to have a way of not covering their product.

I bought this fridge 2 years ago. I had multiple repairs already. Now the side panel makes noise when you shut the door. Repairman told me it is the foam separating from the side panel. There is nothing that can be done. I also have extended warranty.

I purchased a Whirlpool washer 7 months ago, and a month ago, it broke. I have been without my washer for 1 month, and it has been repaired 4 times in that month. It is still not working. All I get is that, its under warranty, and there isnt anything they can do, but to keep trying to fix it. I have been having to take my clothes to a laundromat, and pay to have them washed. I have asked for them to deem it defective, but they refuse.

I bought a refrigerator from Lowe’s and the refrigerator had a lot of manufacturing defects. I called Whirlpool and 3 techs were sent to my house. After the last tech, Whirlpool decided to exchange the refrigerator. Since then, Whirlpool has been playing games with me.

Whirlpool Cabrio washing machine WTW8800YC0 - My washing machine that I purchased a little over 3 years ago apparently is a piece of junk. Ive noticed a smell in the past few months, even while using Affresh. Now, its making so much noise that we must close the laundry room door while the washer is on. I called customer service and they will sell me a new 1-year warranty for about $345.00. Customer service thinks it sounds like the motor or the gear box! After reading the reviews on this washer, its not worth it to repair. More trouble looms for us. Whirlpool doesnt stand behind the product and as many complaints as there are, the washer shouldnt even be sold anymore! Never buy Whirlpool!

Defective Product: I had to replace the fan motor on my refrigerator, which is barely 3 years old. I contacted the company and they told me it was out of warranty. I asked the repair person if he see this problem a lot and he said no. I have had other Whirlpool products which lasted for decades.

Installers left and Home Depot Cabrio washer stopped with water left in tub. I reset GFIC outlet, tried again and it stopped. Did some research and tried different outlets. Same result. I discovered that if you shut off machine as soon as the GFIC is reset, then the washer will drain no matter what. I have been on the phone with Home Depot and they have no solution but to wait one week for a repairman. Very dissatisfying service. Now I am running a 20 foot, 3 prong, heavy duty extension cord into living area where there are no GFIC outlets and it has been running. I believe there is a fault in the washer, but they must not care if we get electrocuted from the faulty grounding of their Whirlpool product.

I just purchased a new stove after using my old one for 15 years with the same great quality. Its the brand I will purchase when I have my retirement home built next year and leave my new one in the home for my son so he wont have to buy one for 15/20 years.

We have the Cabrio model and are thoroughly pleased with the performance. My only issue is the amount of sounds during the spin cycle. Otherwise, the machine is quiet. I like having the automatic dispensers for soap, bleach and fabric softener. Not having the classic tub makes loading a little different as the clothes need to be distributed around the side of the tub and avoid the center.

Same old story! Whirlpool Cabrio is a lemon! I did pay a service guy to find out what the problem was - $70. I ordered a control board for $210, I still had the problems. I ordered bearings for $80. Yay, my Cabrio works! Well, this was all 4 months ago and here we go again. My washing machine is doing everything it was before I replaced the brand new parts. Im so mad! I spent $360. I couldve had a new washer, not a $1000 Cabrio, but who cares at this point! Anything seems better than this pile!

We purchased our home brand new in June 2010 and with it came all Whirlpool appliances. We started having cosmetic problems with our over the counter microwave about 2 years later (model WMH2175XVS-2). The plastic casing around the door handle started to crack on the top and the bottom and now both pieces are completely gone as they fell off. The handle is still attached and the microwave is usable; however, it looks shoddy. To replace it, we were told by a Whirlpool authorized repair person that you would have to replace the whole door at a cost of $300 or more if you include labor. I am disappointed that this happened and that we cant get it repaired. It makes me think again about purchasing more Whirlpool appliances.

I called Whirlpool about the refrigerator that I purchased in June of this year and nothing was done about it. My situation is that the refrigerator scratches very easily. It seems that it gets scratch only by looking at it. This refrigerator is very expensive and I not even done paying for it and this appliance looks awful!! Susan the person that I was chatting with just told me that cosmetic doesnt cover and there is nothing that Whirlpool can do about. It bothers me that paying so much money for something that it is poor quality material.

I always appreciated Whirlpool’s quality, but this brand new stove in my brand new home is a disappointment. The top, back (control panel) gets extremely hot when the oven is in use. The burners are not as easy to regulate, and the broiler (which is under the stove, a negative for me) didn’t come with a broiler pan. That was an additional cost. I had service out in the first 60 days because the oven wasn’t heating properly.

My hot water tank wont stay lit. I replaced the heating element, and the thermo couple. It will light up now but it only stays on for about 10 minutes.

We bought a fridge in November 2013. Brand new, paid about $2400. After a few months, the fridge wasnt keeping our food cold, was leaking from the ice maker, and wasnt making ice. I called for a repair and about a week later they sent someone out. He assessed it, then came back a week after that to replace the part. Within a month or two later, the same problem. I called for service and was set up with a new company. The repairman called me a couple days later and instead of setting up a time to come in, he says its a common problem, he knows whats wrong, and he will order the part and call me next week to come replace it. A week passed, no word. I tried calling the man back, left several voicemails, and no answer. After another week, I call whirlpool again and tell them I heard nothing from the man and at first they tell me they cant do anything with it since it is an open ticket and I tell them thats not okay. They need to close it, he never even came to the house and assign it to someone else. After they tried multiple times to call the repair company themselves with no answer, they assigned it to a new repair company. Again, it was assessed, a part was ordered and replaced another week later. So now its been well into 9 months of having a worthless fridge. A few weeks after that part was replaced, the problem was back and I called again for repair. I was told if this problem is not solved this time I would be eligible for a replacement fridge. Obviously, it did not work so I called to have a replacement fridge at the end of August. I was told that someone would call me to set it up in 5-7 business days but maybe a little longer since Labor day was right around the corner. I waited, patiently. I called every few days for weeks until mid October and kept getting told it had not been assigned, they are really backed up, it will be just a little bit longer and they will send a message. Mid October, my sister in law called for me and she was told that it was denied because I had not had it serviced within the last 4 weeks. WHAT KIND OF ANSWER IS THAT??? Thats like putting salt on a wound!! I have had spoiled food, constant clean up of leaks, and constant wasted calls to get told that it was denied because it wasnt serviced in the last 30 days while I was waiting for a response from Whirlpool??? So of course I grab the phone and go off. They agree to reopen the case because it was denied for a bad reason. At this point, as I type this, I have been on hold for 55 minutes to speak to yet another supervisor because it has been 2 and a half weeks since they reopened my case and I am told it has not been assigned and the best they can do is send another message.

We bought this dishwasher new from the Brick 2 or 3 years ago. It was bought not because old dishwasher wasnt working, but we needed a new fridge and stove so we also bought a dishwasher to match the new stainless steel fridge/stove. If I could give 0 stars I would. Biggest complaints: It doesnt matter what soap, what setting or how much your rinse/scrape your dishes THIS DISHWASHER WILL NOT CLEAN THEM. Its very rare it actually cleans a dish or utensil properly. If your plate had ketchup on it, it wont clean it. But if you had a sandwich on the plate and managed to not get ANYTHING from your sandwich on the plate, it would come out clean.The drain constantly clogs. We rinse everything, but the drain hose constantly clogs to the point the unit wont drain. Have to remove the unit, take off hoses and blow them out. It clogs because the strainer at the bottom of the dishwasher which is supposed to stop stuff from going down the drain hose doesnt work. If you look at the strainer and the system they use to stop stuff from going down the drain hose. Its no surprise it doesnt work. By design it cant work. My brother in law is a licensed appliance repair man. Sears actually paid for his schooling. He installed and hes fixed the clogged drain numerous times. He agrees. Worst dishwasher ever.

We purchased 29.7 cu. ft. side by side in February 2013. Ever since we got it, there is an excessive amount of moisture that builds up in the refrigerator section. It is to the point that the bottom shelf must be dried every other day; otherwise water spills out the front. Most of the moisture forms around the cold air duct work leading in from the freezer. We placed collection containers under the duct work which helped a little. We also tried various temperature settings, still no help. We tried online support and were given many excuses for the excess moisture. Support advised to change the defrost cycle, which we did and failed to correct problem. Support finally threw up their hands and said to call for service. Unfortunately, we were advised since the unit was purchased in Florida and shipped out of the country, the warranty was void. Try and get service in the Bahamas! Ha! This will be the last Whirlpool product we will ever buy.

The Whirlpool microwave stopped working 14 months after purchase. The technician, who was a complete moron, said that he couldn’t find the problem, but took 129 dollars in service fee, which was extortion. Their appliances are ** and so are the ramrods that they hire to service them.

Six warranty visits and the fridge still doesnt work. Cools to around 44 degrees in the upper part and lower part barely freezes. We have gotten sick from food left in the fridge after two days from the grocery store. It is now approaching two months without the use of our new refrigerator. DO NOT buy a Whirlpool. Apparently there was a manufacturing defect. We are now learning that a $2,400 fridge doesnt seem to be able to be fixed by factory-trained specialists.

From day one I was not happy with the new auto fill washer, I was told I just needed to get used to it! Well I have tried every cycle available and no matter what I try cloths don’t come out clean, using the deepwash cycle Sheets on top were still dry once cycle was completed!! Give me back my old washer! Washed much much better.

My husband and I, purchased this washer on November last year, I used twice before and I noticed that the clothes felt hot, but the cycle was COLD water. Now use it again until June 2015. In every cycle the clothes were hot, I started calling to get an appointment in June at the 1800-253-1301, but the system was down twice. Then in July then again the system was down, then August 10, system was down. I did not wait more and called back the next day, August 11, got appointment for the 20. A technician came, he told me that the hoses was switched, but I know the hoses was installed correctly, my husband was here at the installation. He knows the proper installation of the washers.

Never again will I buy a Whirlpool product. I paid over $800 for a new washer 51/2 years ago. I had it worked on twice under extended warranty. Now the bearings are out of the tub and it sounds like a jet taking off when it spins. I had whirlpool products in the past and they lasted for years with no problems. I have a friend who has a relative who is an engineer for whirlpool and his job is to engineer their products so they fail within a certain time frame. They dont want them to last like they use to. They now have gotten their product line to the point where they can tell when it will fail. This is crap. What happened to products that lasted like they use to. NEVER BUY WHIRLPOOL.

Bought a Whirlpool standing freezer EV161NZTQ 10/8/2013. Been fine to a week ago and meat was soft, not frozen and veggies on door soft. Dont hear compressor cycling on and off anymore. Still under warranty so well see what repairman says. Things just dont last anymore. Last Frigidaire freezer lasted 10 years but they werent rated good by consumer reports.

Bought at Lowes. Washer was horribly out of balance on first use. Called warranty # to get service. Was made appointment by Whirlpool for next day. Too good to be true I thought and I was right. A week later, repair company called to make their own appt, chuckled and said Whirlpool does NOT make appointments for them. They came out to see washer and at the time of appointment, the guy said sometimes they come from the factory not hooked up right inside and after he went back to a lady in the office, Jonnys Appl Repair, Bozeman, MT said they would not fix it because washer was not sitting on a concrete floor. They are idiots. Finally, washer completely broke 7 months later. There was no service that would honor ANY appointment Whirlpool made. Went through 6 repair companies trying to get a close appointment date. Hopefully next week will be the magic repair. GO WITH SEARS. Repair is directly through them and they show up when they say they will. Ive never had a new product not working right when purchased at Sears.

I bought a new non-frost 14 cubic Whirlpool fridge Model # W4TXNWFWQ in 2013 from PC Richards. The freezer keeps getting busted. It actually produces a lot of frost which stops the entire fridge from running properly. The tech said this is a common problem with Whirlpool. I am lucky to have bought the 3 years warranty. But when I call to fix the problem it always takes them a few days and I have to miss work for this non-sense.

This is an ongoing problem. I have had to thaw the refrigerator (which takes over 24 hours). Then I blow out the drain with my air compressor, run water through, etc. The drain freezes up a good way down. It is a big pain in the **. There has to be a design flaw for this to continually happen. I paid for a repair man one time but he did nothing different from what I am doing. I cant afford the prices they charge. Shame on Whirlpool for making inferior products.

Cabrio Washing Machine - I purchased my washer and dryer in May of 2008. I had problems with sheets, towels and pants getting very twisted and tangled, but I just attributed that to a design flaw. My problems really began in January 2013 when loads were not level all the time. It didnt matter if it were 1 shirt or a load of towels; you had to stand by the machine and it took forever to finish a cycle.On 1/11/13, the first repair was the rods that kept the drum stable. $260.82 later, it worked again. On 2/16/13, the washer quit working. On 2/18/13, the repairman was back out. It needed a lid lock switch. It was $87.14 that time and he would be back when the part arrives ... There was still no washing machine. On 2/21/13, he returned with the lid switch and replaced it. That was $178.04 but wait, there were still other error codes so there was no working machine.I refuse to pay anymore as I now fear I will be buying a new machine after spending over $500 in less than 6 weeks, but Whirlpool did the right thing when I called and they agreed to repair the machine. They wanted a different company to come diagnose the problem (the machine gave an F50 and F51 error code to the repairman here on the 21st), so I have to wait for another repairman to come and look at the same codes flashing on the LED readout.On 3/1/13, the A&E repairman that Whirlpool sent out arrived at my house. I have been without a washer since the 16th of February. He diagnosed the problem and said that it is a $1,000 repair! I called Whirlpool and asked for a new machine, instead of throwing more money at this one. They informed me that if I didnt like their offer, they wont do anything then. I agreed to the repair.Parts started arriving at my house. On 3/13/13, another A&E repairman came out and started to fix the machine. He informed me that there was more wrong than the first guy thought, but he had the circuit boards so he would get it going. On 3/24/13, the washer quit working again and was flashing an F51 error code. This is the biggest piece of junk I have owned in my life. I have missed 5 half days of work since January and there is no end in sight. Why is Whirlpool allowed to get away with such an inferior machine?

Whirlpool built in Electric oven Self Cleaning Model # GBS307. Dont Clean your oven! Everytime you clean the oven, the thermal fuse switch will burn up on you and will cost approximately $150.00 to fix. Dont use the self cleaning on this oven!

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

It is a really great microwave, but the door is falling off of it. We can still use it, but try to be careful about it. I honestly and truthfully love my whirlpool microwave as well as my whole set of whirl pool appliances. The door is trying to fall off, but we can still use the microwave. If we get another one we will probably get another whirlpool because I love it so much.

I knew I couldnt be the only one with these problems. The reviews confirmed it. I bought my Cabrio washer in 2012. Energy efficient, no agitator to catch on clothes, Great. It took me a while to figure out that the machine was eating my clothes and not cleaning them at all. Oh, they smelled fresh. That HE detergent smells nasty. The machine ate the edges off my good towels, T-shirts, jeans. Brand new underwear (thick elastic) was stretched all the way out and pulled. Normal stains and dirt do not come out even with pretreating. I started running my clothes on the delicate cycle, prewashing stains in a bucket by hand and then putting clothes in mesh bag before running the load. They still came out dirty and ruined. When I run the loads, it still registers as not being that energy efficient on the controls. Id gladly trade it back for my old washer. I feel like I have stepped back in time to a time where you washed everything in a tub or bucket. What a waste of time.

I purchased this Maytag clothes washer in 2007. So far Ive had to purchase and replace the front door 2 times. The current one now needs replacing. The plastic near the hinges disintegrates after about 2 years. This appears to be a manufacturing design defect. I have requested from Whirlpool to send me a replacement door for my washer. The part number is 34001178. The model number is MAH2400AWW. The Serial number is 14060452LE.I have spoke to four different levels of employees at Whirlpool after escalating the service request. Each time they have told me they are unable to send a replacement door to me, stating that the product is out of warranty. I realize that the washer is out of warranty but I believe this problem is a design flaw. The plastic near the top door hinge breaks down and cracks after 2 years of normal use. The last person I spoke with Michael (would not provide me with a last name) said to write to the Whirlpool corporate office with my complaint.

I purchased a new Whirlpool top load washer and dryer in 2012. I heard all kinds of crazy stories about all the new machines, so I tried to stay with the regular top load style. About 6 months ago my machine seems to have lost its mind! It forgets where it is in the cycle and pulls hot water when it should be cold and the washing machine has even overflowed all over my laundry room floor. I tried unplugging it, but thats just a temporary fix, it goes right back to its antics! I had my last washer and dryer for over 12 years. Im really upset that I spent a small fortune on this machine and now it needs repairs! Repairman is scheduled for next week. I will never buy Whirlpool again! JUNK!!!!

Purchased above refrigerator (WRF736SDAM13) over a year ago and it has been nothing but trouble. Ive had service companies out 6 different times. The doors never lined up or closed properly from day one. The final and last attempt to fix was putting caulk in the seal of the doors!! Left door does not seal properly and moisture builds up on inside. I requested several times for a new one and Whirlpool refused. Also purchased microwave, stove and dishwasher. Microwave went out 6 months after using it. They had to replace a major part. At least they did this at no charge. Just the hassle of having to be home 2 times to meet service tech. WILL NEVER purchase Whirlpool appliances again. Ive been using them for in all my homes in the past. STAY AWAY from this model.

Purchased 2 sets of the full sized refrigerator and freezer combo. First was 2005 and second was 2015, both new build homes. We had a few probs with 1st set but the 2nd has been a nightmare. Just like others we have lost time and food because of the constant problems. Avoid @ all costs!!!! Apparently they only care about lining their pockets and not the consumer.

I bought the Whirlpool Cabrio top loader set in 2006. Honeymoon was over after the first year and I had to change the dryer element then the washer with the F51 code six months later. Last year, I had to replace the heating element again! For the last six months, I have been dealing with the dreaded UL on the washer. I cant afford to pay a technician $100 to come out and tell me whats wrong let alone what they will charge to repair a problem that, from the looks of this message board, will never be fixed. I have no choice but to get it fixed in order to sell the ** machine. I paid $1400 for this brand new set and have already invested $500 in repairs. How is this possible? I had a 20-year-old machine prior to this and never had an issue. There are lemon laws for cars, why arent there any for appliances over a certain amount? How in this day and age can a company be allowed to sell such garbage? I will never, ever buy another Whirlpool appliance as long as I live. Any other brand can have my money any day.

I purchased a Whirlpool hot water heater several years back with every bit of the Bells & Whistles that Lowes could bestow on it paid for and documented on the tank; Limited Lifetime Warranty and Lowes Professional Installation. It failed after several years with multiple problems. First, the bottom heating unit failed at the same time, noticing a leak from the top heating units external cover where a supporting screw had popped out, leaking down to the floor. Not only was the Whirlpool 800 number a scham of silence, with no estimated wait time and after approximately 20 minutes, a rep picks up as I could hear their legal department on an alternated line instructing and listening in, then dropping off when those crooks felt I had been placated enough to go onto to the next sucker. I have all Whirlpool Gold & KitchenAid Superba appliances in my kitchen and never thought I would be saying this but I will never purchase another Whirlpool Appliance or shop at Lowes again!

I had to purchase a new fridge quickly due to a power surge and this was the only one available with features I wanted. It is too small, but thats not the fridges fault. Has worked well and easy to clean. Simple white fridge that Id recommend. Not expensive and for the past year+ dependable.

I have had my washing Machines since 2011 and have had continuous problems with the washing machine during spin cycle sounding like a freight train going through my house. Whirlpool has had people to my house 5 times to fix. When warranty was up in 2012, I was told they would continue to cover this particular issue. They came out again in April 2013 and now I am being told, Too bad; if you want fixed then you will need to pay for it.

We purchased a Duet from Lowes just a few months ago. Within 2 weeks we had an inoperable machine. After 2 phone calls a service technician came out and looked it over. He had to come back a total of three times to replace the motherboard. That worked for about six weeks and it died again. He came out again and replaced the motherboard again. Fast forward two months and the machine is once again inoperable. When plugged in, it makes an ominous growling sound but nothing else happens. The idiot who designed this thing has no common sense. Its programmed so that it will LOCK on any failure. Not only has every one of these episodes left us with a load of clothes in there getting moldy, you cant even get to the model number or serial numbers; both of which are only visible inside the rim of the machine.So adding insult to injury, your machine is broken, your clothes are in there getting ruined, and YOU CANT EVEN GET TO THE INFORMATION YOU NEED TO SET UP THE SERVICE CALL. If it had only happened once, Id laugh, but this is the third time and its not funny. We bought this machine because it said proudly made in USA. Next time, Ill support the Korean economy and buy a reliable, durable Samsung. The only positive I can offer is that the Whirlpool live chat person was able to set up the service call for me even though I cant get to the relevant data inside the machine. DONT BUY A WHIRLPOOL WASHER. Despite their legacy and US-feel-good associations, the sad truth is that they are poorly engineered and poorly manufactured.

We purchased a Whirlpool Cabrio washing machine in September 2006, and have had nothing, but problems. I constantly have to get online to check error codes. Several months ago, the washer just stopped working. We called Whirlpool technical support. They said wed have to pay for a repair. After several calls to Whirlpool for help, I found online references to a recall for the same problem. Whirlpool NEVER mentioned that the washer was recalled for the very same problem. I called them back with the recall information, and they politely sent someone out to rebuild the washer. Less than a year later it is no longer working, again. I went online first this time, to check for further recalls and complaints about the current problem (faulty control panel). I found many complaints about the same problem--even a reference to a class action law suit. Whirlpool said they were unaware of the problem, didnt have many complaints, and are unwilling to help. I asked for a supervisor, Benjamin, and he said there was NO means by which I could further escalate my complaint.

They will not honor the extended warranty on their fridge which Ive had for less than three years which will not defrost making me lose thousands in spoiled food. Extended warranties are contracts and this company should be penalized and shut down for fraud.

I bought new hot water heater. I installed it did and it did not work. I called them, and they sent a new part. A service man installed it, and it still did not work - he was unable to get it working. They said my gas supply line 1/2 od was too small. I had it replaced to 5/8 od 1/2id, and it still did not work. I called them again. They offered to send more parts and try again. This is a brand new water heater, never fired. I asked if they would give me a ra number so I could return it to the store. He would not give it to me. He insisted he send some one out to try to repair it. Meanwhile I have had no hot water for 2 days. He told me do what I have to do and hung up on me. So I removed the heater and took it back to Lowes, where they were glad to give my money back. But still, I lost a day of work and paid the gas yo bring it back. I went to home depot bought a GE hot water heater. I had it installed in about 15 minutes and it is working fine.

Im no longer buying Whirlpool products. They do not all up and are made like crap. My Cabrio washer being the most recent problem. Hinges broke on the lid and the drum spring broke. Out the door it goes! Im having my American made Speed Queen delivered tomorrow, the last Speed Queen I owned last over 30 years.

Mine came new with the home I purchased 3 years ago and so far I have had no problems at all. The only drawback is that if it is on, you can hardly tell it is running so if you forget you might interrupt the wash cycle unintentionally. It does an excellent job on dishes and the stainless steel front is easy to keep clean since there are no mechanical knobs or switches, you can just wipe it down and be done in less than a minute.

I had kenmore in long term until we decided to change the brand Whirlpool. We just saw want to updates to change the color. It was good price on special day. I have no problem with the stove. I like there is size of pots from small to large pot of size.

I purchased a new Whirlpool Cabrio Platinum washing machine 2 years ago. Do not like it at all. Does not get my clothes clean. Pulls threads in my clothing. When I wash clothes on the normal cycle they are barely damp when the cycle is finished. When I use fabric softener it leaves blue spots on my clothes. I cannot afford to buy another washer so Im stuck with this one until it breaks. I would NOT buy another Whirlpool high-efficiency washing machine ever again.

Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it worked for about 10 years and I am fairly happy with that but I have a warning, my control panel shorted out putting out thick black smoke and I was unable to turn off the dishwasher. I had to turn off the switch at the breaker box. If my wife had of been the only one home she would not have known how to turn it off and would have had to call the fire department. I dont know if the short would have led to an actual fire but with that much heat I have to believe it would have. Warning, dont run the dishwasher when no one is home. Hope this helps someone.

Whirlpool model WRV986FDEM Purchased May 31, 2017 from Lowes. Cost: 2,638.10 including 229.97 for the 5 year extended warranty. We’ve experienced four failures in the nearly four years we’ve owned this lemon. The first failure occurred within the one year manufacturer’s warranty period. The three failures since then have been fairly close together. Control boards and mechanical parts have been replaced. We are now waiting for a “made to order” part, with no scheduled delivery date. When I pressed Lowe’s on the reliability of this fridge, I was told that if four failures occur during the extended warranty period, they would give us a replacement. Considering the delays in repairs and frequency of failures, this is unacceptable. Do Lowes and Whirlpool expect their customers to just suck it up and do without a refrigerator for months while we wait? The warranty is worthless without prompt problem resolution. Whatever happened to real customer service?

Over the course of the 9 years that I had this hot water heater, I had to have the smart control box on top of the water heater replaced 3 times for burning up. The wires in the smart control box literally burned up and melted together. I am thankful that I was home each time it occurred, because if I had been at work when it burned up and not able to shut off breaker to it, as I did every time this happened, my home may have burned down because of it. I did just get Whirlpool to replace this hot water heater with a brand new one. However I have now paid installation costs twice. Thats not right. I had to pay a plumbing company $725.00 today to just install this new one. I bought the highest priced hot water heater that was also considered top of the line 9 years ago. I did this because Whirlpool is a reputable company and it came with a lifetime warranty. This doesnt make me happy and satisfied though when I have had to pay to have it installed twice. The installation costs more than the price of the brand new hot water heater! I also called around and did my homework first. The company that installed it was actually the lowest price of all of them.

I dont know who is the bigger idiot. The designer of this washer or me for not reading the countless bad reviews. I bought a Whirlpool 4.3 CU FT TL WTW5000DW machine on 7/19/2015. It does not come close to cleaning clothes. It now takes me three times longer to do laundry because I have to check every piece of clothing for any stains. These are minor stains mind you but, they will not come out unless I use something like Spray and Wash. My time is valuable, maybe I should drag my clothes to the river and beat them on a rock. Very disappointed.

Purchased Whirlpool dishwasher and range approximately 16 months ago. Dishwasher must stop in middle of rinse cycle because the dishes always feel filmy and there is an inch or two of water in bottom. Must be bailed out by hand. Piece of garbage. Called Whirlpool and they can get us a service man from 8-4 (who waits an entire day these days) on New Years Eve. Next appointment is following week to examine and will fix (if it is their fault and for a fee). The last two dishwashers I purchased lasted 10 and 7 years respectively. Stay away if you dont want bad equipment, uncooperative service, and aggravation. Range I bought was OK but the oven temperature is always off 10-15 degrees from what it says it is. I honestly wanted to buy American but I feel cheated. Next time Ill try Samsung and see if they give a damn.

I spoke to Sue in Tennessee that refused to let me speak to a supervisor regarding replacing a light bulb in my microwave. Sue insists that I can do this, despite no instructions in the owner’s manual and warnings all over about electrocution if I open the panel. Sue refused to assist me and is sending out a repairman. I will never do business with this company again, and I am angry that Sue refuses to see a problem with me paying $75 to replace a light bulb in a nearly new microwave. She continued to give me incorrect instructions on how to replace the bulb, and the owner’s manual does not have instructions nor do they exist on the internet. The owners are not supposed to dismantle this model, but Sue at Whirlpool Customer (no) service told me that I have to pay. Seriously? For a less than two year old microwave? Never again. I think I will take this unit out and get a GE.

They stink. Major issues with most all of these Whirlpool water heaters. I have had issues with 3 different units. I own properties and these are pure junk. Cant find parts and have to pay for shipping on warranty parts! 2 years old units junked, Ridiculous... never buy Whirlpool!

I just purchased a top load wtw5000dw01. There have not been any changes to this revised model except the lid only locks in the rinse/spin cycle now. If that even helps anybody. It still has the noisy agitator which is the thing I hate most. Whirlpool engineers better go back to the drawing board and redesign their washers. Whats this country come to when you spend a pile of money on something that sounds like it is broken from brand new. I also had a washer that was 15 years old and never had noise issues or problems with it. Its just not Whirlpool that uses this so called new technology.

I dont know the model you have but this exactly what I just had happen in May. Its what they call the jazz board that is behind the light area inside the front of the refrigerator, where the light bulb goes. This is a circuit board and it seems when connection arent happening properly the fridge wont go into defrost mode and the water freezes over the evaporator not allowing any cold air to the top but working cooling freezer and making lots of frost too. I paid $400 to Sears service repair. The jazz board itself, I kept the old one and you can buy it online for about $100 and a child can do the labor that I paid hundreds for because, like you, I didnt know what the problem was. It takes less than 1 min to do this. I was furious! I hope this helps you and I too will never buy a Whirlpool. I found this site looking for why the refrigerator is making very loud noises, very loud banging, clicking, humming. Its ridiculous!

Last week dishwasher leaked. Set up repair with our local gas company that has service plus. Came today. Repairman showed me there is a hole in the bottom of the tub. Upon closer inspection it looks like the manufacturer drilled a hole that wasnt needed so they routed out a depression in the tub and must have put in some sort of plug or filler of some kind which now came out. I called Whirlpool and explained to lady about the defective tub. She said well if it had a plug of some sort put into the tub it would have fallen out before this. I said Well it didnt it just must have happened as it never leaked before. She said it is no longer in warranty. I told her this is a defect to me as if you drill a hole in the tub that wasnt necessary and then the plug failed that you put in to hide the extra hole. It is a defect not a warranty issue. Upshot is she wouldnt do anything about it. I told her I have always bought Whirlpool but if this is their policy its the last time I buy anything made by Whirlpool. After reading all the complaints registered here about Whirlpool I guess I am more than fortunate as my dishwasher (bought in 2006) had run great until their plug fell out (Great except for all the rinse aid that has leaked out for several years.).

Bought this machine in Feb 2007 as a pair Whirlpool Cabrio. I loved it for almost two years. The control board went out, Whirlpool replaced it. A couple of weeks later, the F-1 codes started then the F-51 codes. On July of 10, it was code after code. It sounded like a jet taking off and constant unbalanced load. I called repairman and was told to go buy new machine as repairs would start at $500 and since I live in a rural area, no one wanted to waste their time. Two repair techs told me point blank they wouldnt even touch it. We paid $1000 for this machine and we live pay check to pay check. I spent four months trying to get Whirlpool to do something. I kept getting told I should have bought extended warranty. Machine has been sitting under stairs for over year waiting to see if class action or recall can be done. Also when control board was replaced, the repair man told me it was rusting away from the inside out. My husband had to find us a used washer and this thing has done nothing but cost us money. So much for efficiency. Everyone posting here also needs to go to Whirlpools Facebook page and post there.

I have been having a problem when washing my jeans in the Whirlpool Cabrio that I have never had before with my old washer. When I wash my jeans, there are always a few pair, never the same ones, that have an odor like dirty dishrags on them. I always hang my jeans to dry so I do not think it is this. I have tried to add a freshener to the wash cycle, it does not work. I have tried to dry them in the dryer with a scented dryer sheet, it does not work. I am assuming after reading these past complaints from other consumers that it is not getting all of the clothes clean because of the lack of water. I always use the deep water cycle, but maybe it is not enough water as previously suggested. I have had an issue with blankets and other heavy items not getting clean and/or not even wet. Thoroughly disgusted with this appliance!! I love all of my Whirlpool kitchen appliances though!

I love Whirpool products. They work well, even under hard water conditions. Ive had my Whirlpool washer/dryer for 12 years now without one single problem. Even with the hard water problem in my house, the clothes still come out clean, the dryer works well, I do clean my vent each and every time after each dry. I also have to clean the area where I put my detergent in due to the hard water and the machines are still working great.

Let me start out by saying that I had a Whirlpool washer that lasted me for over 25 years and done a great job of washing my heavily soiled clothes. One day it refused to run and I tried to get parts for it but it had become obsolete and no parts were to be found for it, so I had to buy a new washer. I chose whirlpool again and let me say that it was a huge mistake. This model is a low water, high efficiency, top loading machine. It has nubs in the bottom that agitate to clean the clothes. The first time that I used the machine, I found that I had made a mistake purchasing this machine. It does not clean the clothes and there is NOTHING efficient about this machine. I have to run the washer twice to clean my clothes and they are still not clean. It leaves soap in the clothes and does not rinse them clean of the soap. What it does very well is extract water from the clothes during the spin cycle. This washer really turns up the high RPM`s on spin cycle. It has ripped apart several of my shirts during spin cycle. Whirlpool really failed badly on this machine. I see clearly now that Whirlpool is not the company that they used to be back in the 1980`s. I still have the whirlpool dryer that I bought back in the 1980`s and it still works very well. To end this story, I loaded up this NEW WASHER in the back of my truck and took it to the scrap yard and I asked them to destroy it in front of my eyes. I wished that I had recorded the destruction of this piece of JUNK and posted it on YouTube for the world to see. I got over $450.00 of pleasure watching the crane operator completely destroy this pile of crap. GREAT JOB WHIRLPOOL … YOU HAVE LOST A CUSTOMER FOREVER. I WILL NEVER BUY ANY OF YOUR PRODUCTS FOR THE REST OF MY LIFE and will advise others not to buy Whirlpool products as well. I am a male, 62 years old and work hard for my ill spent money on your JUNK. Life is always a trial, live and learn the hard way. Warning to all consumers. Do not buy Whirlpool products ever!!!! Whirlpool can K.M.A!!!!

I bought my new ceramic top electric range/oven with convection, and the aqua-lift cleaning system in spring 2017. The aqualift cleaning function is a joke, so be prepared to be down on your hands and knees scrubbing. Im careful, and Ive not spilled anything yet, but the oven still gets splatters from roasting meats, etc. Id hate to see what Ill have to deal with when I actually let something spill. Today, as I was down on my hands and knees trying to clean it, I noticed that the enamel is chipping off where the oven racks slide in. Great. I have never had an oven where the enamel came off, much less within a year. I am struggling with heart failure, and I am not up to fighting with Whirlpool.

This is my first electric range. It’s amazing! It cooks evenly and at the exact temperature! The stovetop has size adjusted burners, again at the precise temperature. And the look is very sleek & modern, perfect for a new kitchen! I am so very pleased.

Greetings: I purchased a Whirlpool refrigerator on July 3, 2014. And the supports for the door to open and closed have grinded and worn out - not allowing the door to close properly, requiring being lifted up, and pushed close as much as possible. Not the quality I expected with the purchase of a Whirlpool product. I want this door repaired or replaced at the expense of Whirlpool. Having paid over $600.00 for the product, I didnt expect no problems like this at all, poor design. The weight of the door is too heavy to support a hinge mount in plastic, its ridiculous. Now cooling is being wasted, runs constantly, and just not the quality I expected nor received.

GS6SHEXNB02 Whirlpool Gold Refrigerator - Bad ice maker module. Ice maker valve is bad. Its gone out 3 times a year since I got it. We order a replacement, it goes bad again. Its not the ice maker itself, its a bad valve. Signs its going out, ice maker stops making ice or the ice cubes are small or the refrigerator water will start pulsing coming out (start and stop). Whirlpool made a bad product and they know about. Several complaints online about the ice maker no longer making ice. Bad product.

Purchase whirlpool washer model W2W4800xQ2 in Sept. 2012. Had problem with lid lock after warranty. Now lid lock does not work, takes 1/2 hour to start wash and does no spin. Called whirlpool and they will do nothing. Repair will be $200. I opt to just purchase new machine. This machine is one piece of garbage.

We purchased 4.0 cu. ft. Cabrio Top Load Washer with 6th Sense Technology MODEL WTW7340XW2 on 11/20/2011. We are a small family of 3 so use of the machine is light. We noticed a strange sound and some leaks a week ago and called in a technician recommended on the Whirlpool website. To our horror he informed us that we need to replace the tub bearing assembly, rotor and stator - to a cost of $1095! This machine is not even 3 years old. Did we buy a lemon? I called Whirlpool. They were simply not interested. The online chat person sent me to the Whirlpool Customer Experience Team where I was told that I should buy an insurance plan to cover the costs of repairs. They then sent me on to the insurance department who want me to pay $338 to buy a repair plan to have the machine fixed. And then referred me to the Manufacturing division when I wanted to know how to escalate the problem - and if you call that number - there is no option to deal with problems - seriously?!? Is this what I should expect when buying the Whirlpool brand?

In remodeling a house, we got all Whirlpool appliances for the kitchen, right when the lockdown started our freezer went out, 8 visits later from a local repair person, Whirpool will not honor the warranty and get us a new fridge!!! They just want the repair guy to keep replacing all the parts he has already replaced, the repair guy is beyond frustrated with Whirlpool and their crap!!! Never again, totally lost a customer here.

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

We bought the over-the-range Whirlpool microwave, model #WMH53520AH-1, about four years ago from Pacific Appliance Sales Kitchen and Home inside a Best Buy store in San Diego. The Magnetron and Diode have malfunctioned and been replaced. Now the plastic around the door is falling apart, cracking, and splitting. This is unacceptable, poor craftsmanship, and low quality for the price of this Whirlpool appliance. This needs to be reported to the company and properly addressed. Until then, were staying away from any Whirlpool related products. We also own Cabrio W/D. The washing machine has had problems from year one. Im submitting a separate review for this appliance. Consumer beware!

Design is made so you will need a repair man to clean filter. The machine has to be taken apart to get to filter. About one hour of your time. If youre not handy its a paid repair About $250 to $300. Also the valves that control the water into the washer failed after about 5 years. An easy fix part costs about $60. All appliances are designed to fail after the purchased extended warranty expires. More features more repairs. So if you arent going to use a feature get a simpler machine. More money does not mean better machine. Or that it will last longer. The days of an appliance lasting 10 to 20 years are over.

I bought the washer Whirlpool duet on June 2009 (2 years and 2 months to date) and suddenly gave me an F70 code and died on me. It would cost me about $550.00 for parts and $129.00 for labor which is almost $700.00 in total. Its a communication error code where the CCU or the Motor Control Board was the culprit. I called the company for a concession consideration and they said they go by the warranty period. I should have read reviews for this company washers. Now, I have to find myself a better washer. I will never buy Whirlpool again. What a ripoff!

I bought a whirlpool cabrio with high hopes. Unfortunately, it has been the worst washing machine I have ever had. Then I moved in with my fiance and he too had a cabrio. It too is a piece of junk - and brand new! Every load comes out with left over residue and the clothes look worse than before they went in! I have tried everything and I do mean everything! IM 41 y.o. - IM well aware of how to load a machine. I load it just the way the instructions say: as if there was an agitator there. Ive tried using no laundry detergent or fabric softener - clothes still come out disgusting. Ive made sure the screens are clean, doing extra small loads, turning on the extra rinse, everything! Ive called whirlpool, but there is no such thing as customer service anymore. They just blamed me for not loading the clothes properly and blew me off. The machine becomes unbalanced very easily (it is leveled on the floor), sometimes the clothes are still soaking wet at the end of the cycle and sometimes all knotted up. This is a horrible machine!! I wish I could say it makes me feel better that IM, by far, not the only one having issues with this piece of junk!

I would not, at this time, even really give this product 1 star, but that was the lowest rating allowable. We purchased a Whirlpool Gold French Door Refrigerator at Lowes a couple of years ago after our Amana was toasted by a close proximity lightning strike. (It got more than just our frig, but the replacement frig is the only item we have had issues with.) We even got the extended warranty thru Lowes for the unit. Shortly after the extended warranty expired we started having issues with the bottom freezer door icing up. We thought that possibly the grandkids had not shut the freezer. So we cleaned up the ice around the door, but the problem persisted.The ice cream in the freezer was rock solid, to get it out of the container you had to put it in the microwave for a couple of minutes. The items in the frig were also frozen. So we emptied the frig and freezer, unplugged the unit and let it sit for a couple of days with the doors all open. We then plugged it back in and hoped for the best. It seemed to be ok for a couple of days then the ice on the freezer door appeared again. At this point, I contacted Whirlpool to see who was a licensed repair company in our area. I contacted the licensed repair service, explained my issue, they got the model and serial number info and ordered what parts could conceivably be the culprits.The tech came, the unit was frozen up, all the vents in the freezer were showing icing. So he removed the back of the freezer compartment and thawed the unit out. At the same time I mentioned that the ice maker had quit working, he found that the wiring connection was not properly connected and fixed that while he had all the stuff out. After re-assembly he ran all the diagnostic tests Whirlpool lists and found everything passed. Since the boxes of parts had not been opened they could all be returned to stock. So no charge for parts, as he could not find indication that any were needed.So 1 service call at $100 and it appeared that maybe the issue was resolved, not the case. Not even a month later, issue re-occurred. No grandkids had been there, no instance of the freezer possibly left ajar. Another service call, and by the time the tech arrived, since I had unplugged the unit and emptied it again, all the frost/ice was melted. $100 for a service call, tests all came back as nothing indicated as not functioning.So if I dont put too much stuff in the freezer or too much stuff in the frig it will run without freezing up for about a month. Oh and weekly put it into the defrost mode a couple of times. Now it has started making a tic-tic-tic or rat-tat-tat sound to the fun and games. If the noise is non-stop, it only stops when you open the freezer door. Leading me to believe it is a fan. (Correct, I was told by the local Whirlpool licensed repair facility.) I have spent the weekend, again thawing out my unit in hopes that the noise will cease. It is loud enough to be heard at the other end of the house.No such luck, so I spent an unproductive 1-1/2 hours on a call to Whirlpool yesterday. The larger part of the time was on hold waiting to talk with someone, anyone. Due to our unusually high call volume, wait-time is long today. Thank you for your patience. To retain your place in line, do not hang up. Finally, I got a rep named Karen, who sounded like she was almost asleep. She had very little to offer except, Im sorry you are experiencing these problems. I have no record of previous complaints like yours on record for this model of our product.Hello, I found 929 reports of the same issue on Consumer Reports. Oh, you cant believe what you read on the internet was her response to that tidbit. She offered to sell me a Repair Plus 1 Plan for only $359.95. A licensed repair service comes, repairs your unit and the plan gives you ONE YEAR of peace of mind. Lets see... I said... so you are offering me an extended one year warranty? Oh, but it comes with a repair first then one-year peace of mind. Seems that Whirlpool has moved into selling warranty extensions rather than fixing the issues with these Whirlpool Gold French Door refrigerators. With what I have already paid for service calls added to this Repair plus 1 Plan, I would have invested $$$ enough to BUY A NEW FRIG that is not a Whirlpool product.Seems a bit foolish to me. So Whirlpool is not admitting that there is a design or manufacturing problem with these units. Even the ones sold just this year seem to have the same issue. They have not corrected this and it appears they have no intent to do anything about it. She did indicate that they had a known issue with the drain and that a fix was offered for that (a redesigned drain unit could be installed). But since I was not getting ice build up on the bottom of my freezer compartment I did not appear to need the redesigned drain unit. Her evaluation of my issue was that the drain did not appear to be a problem.So after a fruitless call to Whirlpool, oh and they did have my previous emails concerning my issues on file but did not consider my complaints to be part of a known issue, I have the local tech coming back to see if possibly there is something, anything to be done with this refrigerator. So another $100 at least, likely no resolution if the service tests all come up normal again! So when the tech comes, I am going to ask him to contact the service engineer that he is supposed to have the contact info for (per Karen at Whirlpool) and see if he can get any resolution to my issues by using that service engineer.

Ive had my Whirlpool Refrigerator for 2 years. Within that 2 year period, all 3 of the drawers within the refrigerator have broken and now there is a crack in the freezer on the bottom starting in the front and going straight back on the bottom to the back and up the back. After pleading my case for a new fridge to their Customer Satisfaction Department and everyones supervisor therein, theyve offered to pay for the epoxy repair. Im very dissatisfied with this! I dont think that a $1300 fridge should be held together by glue after only 2 years. Ive been waiting for one of the drawers to be replaced for over 2 months. They claim that the crisper pan is out-of-stock and they have no information if it is in production. Im to call back in 2 weeks to find out the status of that part. I would like to add that my husband and I work 6 days a week and our adult children are rarely here, so this refrigerator is very lightly used. We dont have a household of 6 or 7 people constantly home, opening the doors and sliding out the drawers. The fridge that I had previously was a GE and it lasted 30 years. I guess the next one will probably be a GE. I just wanted something different. Well I got it. Its something broken.

Good Morning. We recently built a home with Pule in Nexton, which is located in Summerville, SC. The appliances we chose came with the dishwasher, stove and microwave. Everything other than the dishwasher has been doing great, but as for the dishwasher I am extremely upset...we are newly weds and received two nice sets of glass and at least 12 of them have been broken in the dishwasher. Please advice.

We bought the microwave new after the 2011 flood where we had lost everything in Tennessee. I wanted to get Whirlpool appliances in the kitchen so all appliances were replaced. We bought a Whirlpool model WMH1163XVU-1 microwave; the unit will run but doesnt heat. I also called Whirlpool and with no regard to customer service at all even with all the complaints... This saddens me because I will never buy a Whirlpool appliance again and my grandparents only believed in them... With all the complaints, the attorney generals office should do something for the people.

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

Very unreliable oven. Oven temperature never seems to get to the proper setting. Do not buy any Whirlpool appliance. They do not stand behind their product. A stove should be relatively simple but Whirlpool managed to produce a product that is complicated & unreliable.