I purchased a 50-gallon Whirlpool natural gas water heater (12 year warranty) from Lowes approx 2.5 years ago. Just before Thanksgiving, the pilot light started going out once a day, then twice a day. Now, I can light the pilot light in Pilot mode but as soon as I release the red button, the flame goes out. I called Whirlpool and received phone troubleshooting support resulting in a recommendation to pick up a new thermocoupler from Lowes which I did. While searching for someone to install (unfortunately Im not that handy), I ran into the thousands of complaints filed about the very same problem Im having over a number of years and right up to todays date. I called Whirlpool back and got the same song and dance. Theyd be happy to help me troubleshoot if I can get the required meters etc. to test devices, do draft tests, etc. They claimed the problems were fixed with the newer model that I have but certainly cant explain why I have exactly the same issue. What they are not willing to do is stand behind their product and get me hot water. Tried calling Lowes and got the response that I have to deal with Whirlpool. It appears that this newer BFG model is just as flawed as the older model and the warranty is pretty much worthless other than getting a few parts. I used to think that Whirlpool products were reasonably good, however, I will never purchase another.

The washer started to show error code for the door and washer would not restart. After removing the top of the washer and checking the door switch to see if there was a loose wire, I traced the wire back to the micro control unit, and upon inspection of the micro control unit, I found that the terminal that the door switch wire was attached to was loose and not making contact with circuit board.Although the washer is out of warranty being 7 years old, this is clearly not a part that is subject to wear and tear. The part was clearly manufactured poorly. I looked on the internet to purchase a new part but it seems that all micro control units are out of stock. This makes me wonder if one should start a class action suit as my part could be one of hundreds that was poorly manufactured. I called Whirlpool to see if they would send me another part to replace the bad unit but they said that because the washer was out of warranty, they could not help.

UL code displayed for six months. Will not spin. Makes a squeaking noise. Recently noticed a black greasy residue around the machine. The bottom of the machine is covered with it. Have had the Cabrio for 5 years. Seems like a bearings issue. Expensive machine. Whirlpool said there are no reported issues with my model even though there are thousands of people on several websites who are having the same issues. Apparently, Whirlpool is in denial and not willing to save face with consumers and correct a horrible washing machine. Definitely will never purchase another Whirlpool appliance.

My experience was terrible. We purchased a side by side refrigerator on June 27, 2011 and it stopped working in December, 2011. We reported this onDecember 19, 2011. A repairman was sent out a few days later, who could not solve the problem because a piece had to be ordered. The piece was ordered and the repairman came to install the part on December 28, 2011.The refrigerator is still not working at all. We have been without ice for this period of time, not to mention the inconvenience of non-refrigeration of food. I pleaded for them to pick up the refrigerator and give me even a partial refund. I was told that three repairs had to be done before they would even consider picking up the refrigerator. I am not a person who complains, but this was ridiculous. I will never purchase another Whirlpool product.

Where do I begin! LEAKS on floor! Gets stuck on cycles! Doesnt empty the fabric softener! Clothes are still dirty! The clothes come out soaked (not drained) of my favorite not wet at all! This washer was the worse purchase ever. I threw money away!

My Duet Sport washer drum is damaged due to the poor quality of the bearings. I replaced the Whirlpool Duet Front Loader Washer Bearing & Seal Kit W10253866, W10253856 but because the bearings were damaged the drum is also damaged. When I opened the rear panel of the washer the bearings had literally come apart and bearings fell out. All of the floor and the oil/grease was everywhere. I replaced the bearings but it didnt matter because the drum is warped. Priced the drum and it is nearly $400.00 to replace the assembly. The cost of the drum assembly is about half the cost of a new washer. I will never buy another Whirlpool product again. Just a shame that the cost of a replacement drum is so high. What caused the bearings to just explode and damage the drum. What did I do to cause this? Absolutely nothing. I have since discovered that this is has happened to scores of people with this same washer.

We purchased this Whirlpool washer 5640XW3 from Lowes. It doesnt clean the clothes. Even if I run them through a second wash cycle, the clothes are still not clean. Called Whirlpool and they said nothing is wrong with it. I use HE detergent and load clothes around the agitator as directed in the manual. Still, clothes are not clean.

We purchased an over-the-stove Whirlpool microwave in January 2011, when we remodeled our kitchen. In May 2014 after a loud pop, the microwave stopped working. This was Model # GMH6185XVS-1. Of course, the warranty is no longer in effect. I feel a high-end appliance that cost $500 should last longer than 3 years. I will not purchase another Whirlpool product.

Purchased this oven in September 2012. Three months in, we tried to use the self-cleaning feature and blew a thermal link (guessing terminology). Tech came out and got the oven open and that was his determination. Also said he would replace both the front and the rear one because it was pretty common that if one was bad the other would probably follow. Said hed have it within a because he had to order it from the factory. I called a week later because no revisit had been scheduled and found out that the factory also did not have the part and was sending me a new unit. Whirlpool was supposed to call and tell me that and did not. It would be another week. Then a few more days for them to come out and replace it and pick up the original unit.Now I have brand new unit again so we tried the self-cleaner. Same issue. To make a long story short I called again this morning and scheduled yet another service call because the oven is inoperable again after running the self-cleaner. This is the 4th time with the replacement oven. They have replaced the thermal units several times and have replaced the fan.Fortunately, when I complained vehemently about the original unit, Whirlpool gave me a one year extended warranty on the replacement so I am still under warranty, which, if youre dumb enough to buy a Whirlpool after reading this, I would advise paying for. If you already have one and are having similar issues, call Whirlpool and insist they give you one for free because they sell junk.This time I told the nice customer service lady that, since the holidays are over and I can get by without the oven, I am going to run the self-clean right after the tech leaves. When it blows and gets repaired again I am going to repeat the process until they refund my money or send me something that works. Whirlpool apparently doesnt care because in their agreement with their service companies they only have to pay for the first visit. After that they just supply parts. I will keep doing this until I run out of service companies in Denver. Then I am going to pay for another extended warranty when this one ends in September 2014 and continue the process.Wake up Whirlpool!! If these units fail consistently at high altitudes (which every tech that has come out here has mentioned as an issue) then fix the problem or quit selling it in these areas.

This piece of junk just broke down not even one year after the purchase. Every singe Whirlpool washing machine has broken one way or another. This one will set the wash time for 57 minutes, and exactly 24 minutes left in the cycler, you hear this big crash and then everything stops. Another dumb thing about this piece of crap is that when the problem happens, the POS keeps the lid locked so that you cant tell what the problem is. What morons would put a lock on the lid? Its not like someones going to take a jacuzzi bath!Restarted the POS again, and exactly 24 minutes left on the wash cycle, there was another crash. Both times, exactly 24 minutes. NEVER BUY FROM WHIRLPOOL!

2 years of use the wash plate went. $150 later, one year later wash plate went again (the wash plate is all plastic, the motor spline in metal total stripes the plastic teeth in the wash plate) I replace myself. 3 weeks later the shift actuator failed which cost another $60 which I replaced. Now the bearing is going. There are only 3 people living in the house. I would stay away from the top loader washers from Whirlpool h2 low series. Huge disappointment.

I purchased 4 Whirlpool appliances late 2014. The French door refrigerator close to a year later made a piercing sound several times during a day. I immediately contacted Whirlpool and the representative directed me to YouTube to listen to the normal sounds the refrigerator would make. My first thought was I have been a homeowner for 30 years and countless appliances and never heard such a horrible sound. At the same time they sold me an extended warranty over the phone. He assured me sounds were covered. The sound just kept getting louder and more frequent. I could not take this piercing sound and called back. They sent a local repair service. At the time the repair person came out the refrigerator was not making the sound. I played a video recording and the repairman even said what an terrible sound it was. He continued to check everything over and said - everything looks good. I dont know what the sound is coming from. I asked, What is Whirlpool going to do? He said, nothing, the warranty ran out and your extended warranty does not cover sounds. What a ripoff! Now the drawers broke and another thing they wont cover! I also have problems with the dishwasher I purchased at the same time. Even putting on the extended hot dry I need to wipe everything off. I should have just open a window a tossed out over 2k. The sound is so horrible I am being forced to junk the refrigerator and purchase a new one. Dont purchase Whirlpool and never purchase extended warranty over the phone.

What can I say. Pretty much a generic refrigerator that is manufactured and sold under various brand names. Nothing special. Keeps food cold. Ice maker takes too much freezer space but thats typical. Interior LED lights failed after a few months. Flicker sometimes. Out other times. Internet research finds this to be a common problem. Zero quality in Whirlpool appliances. I bought four Whirlpool kitchen appliances and ALL have had problems. The only way to own them is with a 5 year extended warranty.

I purchased my Whirlpool Cabrio Washer (WWT5640xw0) at Lowes in East Orlando in 2009. It has worked without issue (other than a slight odor) from then until today, 5-1-12. It has now refused to agitate or spin any clothing, it emits a slight burning smell from the basket, and the basket, when it does decide to spin, spins about as fast as a merry-go-round, banging into the sides of the washer (causing the metal on the sides to bulge out every time it strikes them). It is self-destructing.I called Whirlpool, and they simply refused to address any questions, once I told them that I did not have an extended service plan and that my unit was older than 12 months. I informed them that I refused to pay for an ESP, because I refuse to pay additional monies in order for the product to perform as advertised. They were rude. I said bad words. The call ended.$600 was gone. And I now have to run out and buy another washer, and I can promise you it will not be a Whirlpool. I am a local law enforcement officer. I would love to speak with an attorney about this if a class action suit is pending. I am beyond pissed. My moms chartreuse-colored Maytag still works after almost 30 years of service to our family. It required a new drive belt at somewhere around year 17. The belt cost $45.The Whirlpool CS rep informed me in a surprisingly snarky fashion that it would probably cost over $360 for the total cost of repair and that the only way to know exactly how much is to schedule a service call. I was also told that I would be on the hook for $100 for the service call even if I declined the repair.

Yes, Whirlpool makes Maytag, Im still paying for this junk. Too much to go into detail. I had to bypass the crummy fuse system in the Bravo dryer and hook up my own 15amp automotive fuse in the dryer to keep it working. This after two lame under-contract Maytag repairmen replaced the dreaded board, which did nothing. The washer goes cabunk, cabunk, cabunk throughout the house and shuts down with an unlevel code (no matter how level the load is) every time it does its load during the spin cycle. The dishwasher handle broke off and had to use a screwdriver to pry the handle latch open, until realized it doesnt even lock anyway and just pulled the door open. Now, the dishwasher has this noise problem which means they designed it to allow pieces of debris to escape past the trap like my other dishwasher had that was easy to remove and clean. Do not, I repeat, do not pay the $3,500+ I paid for this junk. Go buy a Kenmore thats 15 years old off of Craigslist! Youll be better off and it will last longer.

Got a fridge Friday night setup, and was not cooling as of Sunday still. Called Best Buy who we got it through and they sent someone out first thing Monday AM to look at it. Per the Whirlpool agreement, the first year has to get serviced through them. Finally got a hold of their service support to get someone scheduled to come on site. 11 days later was the earliest appointment, and they just expected me to deal with no refrigerator for 11 days. I asked of other options, what wait times would be after Whirlpool comes out in 11 days to deem it broken and they repeatedly said I cant give you any what if answers for anything. Were no help at all and just expected me to figure out things for at least 11 days on a brand new 3 day old machine that is broken. The absolute WORST customer experience ever and refuse to buy from them again. Thankfully, Best Buy has a return window so were completely returning it and going with a different brand.

My NEW Machine Top loader HUGE drum. Have problems with clothes not looking like they’ve even been washed, Spun so hard they are twisted all to heck. And white stuff - my oxy powder maybe? Not dissolved. My old machine was a Kenmore 30 yrs old. Thought I’d be able to trust whirlpool but not sure. Am I missing something in the loading process. Seems to read something bout not Covering the knob on the bottom. Is this true?

They attempted to fix our fridge, 1 year into owning, claimed no parts available. Never fixed, fridge died. Refused to repair. Offered us a 15% Visa gift card on another Whirlpool. Unacceptable, they can’t fix their product, and will never recommend anybody go through my familys $3,500 wasted fridge experience. Don’t trust them, they lie, and just escalate it to another liar in the customer service department.

Never ever go for Whirlpool. It has the worst customer service. We brought an oven but accidentally we broke the inner oven plate. We called up the customer care person on 18002081800 and tried asking him the dimensions of the plate pr at least how we could reorder it. He never listened to us. He just got our details. Said that technician will come at 11am tomorrow and disconnected the call when we were trying to explain what our query is all about. Is that all the respect a customer deserves!? Is that how whirlpool trains their service people!? He doesnt even have the basic courtesy to listen to the customer, I wonder how was he even recruited as a customer care person. If you want at least your basic respect, please DONT BUY WHIRLPOOL.

I have always had Whirlpool Everything - not anymore!!!! I purchased a water saver washer that I am very unhappy with - it does not get the clothes clean. I have to put it on an extra rinse (water saver?) to get the soap out. I use the Tide for HE washers. I cannot wash a large load in it - directions say I can. Anything too heavy or bulky will not spin out well. Will bounce all over the place. From now on I will switch to another brand. They push so hard to buy a warranty because they know you will have trouble! Should have read the reviews!!

Watery body from all the refrigerator side since 9 – 10 months and complained to Whirlpool 2 months back. They changed the thermostat 2 times but no use. Problem same. Please help. I complained during the last warranty days. Please let me know.

I purchased the Stainless Steel, side by side with water and ice dispenser, model #WRS325FDAM04 on 11/30/16, paying over $1,600 for the refrigerator. We had trouble from the beginning with the freezer door not closing all the way. When the repairman came out, he said the entire door had to be replaced, as it was warped. Since then, one by one other items are breaking in the freezer and refrigerator. The plastic casings holding the glass shelves have broken on all three shelves in the refrigerator, the wall of the refrigerator and the freezer is cracked in several places, the ice bin has a hole in the bottom, where the device rotating the ice out broke and now when used, ice falls into the freezer, and the bins in the refrigerator have broken as well as some of the door shelves in the refrigerator and freezer.I called Whirlpool before posting a review to provide them an opportunity to at least offer to help in some way. Their response was due to so many pieces missing/damaged they would not be able to help in any way at this time. I purchased a Whirlpool product as I expected I was purchasing a quality product with quality workmanship from a reputable company. I have been sadly disappointed and will no longer support Whirlpool by purchasing any item manufactured by them and will share my experience at every opportunity.

I had the bearing go bad in the tub after a few years of service. It cost hundreds of dollars. As an engineer, I look at this and it is a design made to fail. The seal design is inferior compared to old washers that had a shaft seal made to be on a spinning shaft. This is a rubber lip seal that is going to wear because it is using washer as a very bad lubricant! When the seal goes bad, and it will, the water runs down to the bearings and destroys them, and you have the replace the whole tub as a $300 part!

This product is JUNK!! We replaced out hot water tank 1-07-11. Worked good for almost 9 months. Then the pilot light keeps going out. We have replaced everything three times already. Now we cant get it lit for nothing. Its blinking 7 times!!! This should not be happening. When you call Whirlpool, you always get some smart ** rep trying to solve your problems over the phone, telling you what its doing. Excuse me, your not here with it, I am. I even had the plumber on the phone, he got so mad at them, he handed me my phone back and said he is not dealing with stupid. They have no clue what they are talking about!! Its crap that we have to pay $30 for them to express mail a part when its the middle of the winter and we have no hot water. Im at my wits end with this hot water tank. Im ready to sue their butts. Sounds like to me by reading all these reviews, a lot of people are having the same issue. We need to do something about this. They had a suite against them but not for my water tank. They were replacing the parts. Ive spent over $1000 from buying it new, having it installed and paying for repairs on the hunk of junk!!!What can we do??? We need to take a stand against Whirlpool. We need to exchange information and contact an attorney and make them pay!!

I bought my Whirlpool Convection oven in mid August 2019 from Lowes. I have had to call no less than 5 times about my NEW oven which I am extremely remorseful of buying. I am so unhappy with my experience mostly due to my expectation that my new oven would have been able to meet my demanding needs baking and cooking. I would have thought that it would have lasted longer than 4-5 months. The bottom left hinge is faulty which I am told is an undocumented problem for this particular oven. I noticed that it was having a problem when the oven wasn’t quite making a seal. Slowly it got worse until now it makes an initial click then I can open it about 5 to 6 inches and then have to lift it up so that I can open it without making a horrible noise and a dent in the frame.The first time I called was on Saturday Jan 4th. It took me 1 hour to get through to speak to a person. I asked why I couldn’t get a new door to the oven and they told me the hinges have to be installed separately because this model is made to be able to take the door off for cleaning purposes. They set me up for service on Wed Jan 8th between 12 and 4p. I wasn’t as unhappy at this point. I even got a text saying that the appliance company would be coming between 12 and 2. At 12 when I woke up after working nights, I got a message saying that they hadn’t received the part yet and that there would be no point in them coming. I called Whirlpool again and they told me that the part was on backorder and that in fact the part had to be fabricated and it may take up to 10 business days but that they would have the part sent directly to my house. By this stage I am very unhappy.I called back this morning and told the person that I would rather have a new oven or my money back and that my less expensive and less decorative oven that came with my house lasted me 20 yrs. I get a lot of “I’m sorry” and “I apologize” but that doesn’t fix my problem. I also told them that now the frame of the oven is being dented so I am going to have a less than perfect appliance which is no fault of my own. The only info the person could give me is the tracking number of the part they were able to locate which would be coming Fedex.I tracked it and it was due to come no later than Tuesday night. So I called the original service company in my area who told me to call to set up the service time when the part came in. I figured I would get a jump on it and call. They told me that they were all booked up this week and I would have to wait until next week. Do you think that this is how your customers should be treated? I feel as though I am being punished by choosing to buy an appliance from Whirlpool. I then tried calling back to set up an appt with a new company but the wait time was too long. I had just worked nights and needed to get some sleep. I called back this afternoon and again had to explain the whole situation AGAIN. I was able to set up an appt with a different company for Monday between 12 and 4 which happens to be on Martin Luther King day…so I am hoping it is not a mistake.Do you think this is fair treatment for a customer who just bought a brand new oven less than 5 months ago? Would you like this type of service? Would this give you any confidence to buy products from Whirlpool? I don’t believe that I would be able to recommend Whirlpool in good faith. The people who I have talked to have never been rude or disrespectful however, I feel as though my unhappiness is just par for the course. I feel as though it is just my tough luck and “oh well so sorry” instead of the attitude that you want to make everything right as quickly as possible. I ask myself if the problem was the store I chose to buy from? If I should have gone to Sears and bought one of their products or where I went wrong.

I HATE, HATE, HATE the aqua lift clean feature. Its awful. The bottom came somewhat clean but cook bacon and the sides and top are filthy and the aqua lift cant clean that. I dont know how this ever made it past the thought process stage to become a thing but it needs to go away. Im quite cranky right now as Ive just spent two hours scrubbing my oven while reaching past the oven door that doesnt come off because its a self-clean oven. This is what I have to look forward to for the next 10 years until it dies and I can get a new oven? What a joke!!

Compared to others it gets the dishes clean and is easy enough to operate. Like everything else it has more bells and whistles than I want or use. Fill it up, put soap in and punch the desired settings and it does what it is programmed to do. Overall size seems to be like all the other models Ive used. Stainless with buttons on top of door. The top basket/drawer has latches that get tripped allowing the basket to drop down and confusing my wife. Not the best arrangement IMHO. Seems like the spacing of the supports in the bottom basket are off, but that may be due to our plates and bowls shapes.

Whirlpool’s customer service is one of the worst I have encountered. They consider a 6-7 year old $1500.00 range to be old! I said to her, “Wow, if the population was to throw their Whirlpool appliances into the landfills after 7 years, this would be quite a horrendous situation.” I think its disgusting for a company to build appliances with a shelf life of 6-7 years and with only a 1-year warranty! What a horrible brand! I will never buy another Whirlpool brand product ever again. You spend $1500.00 on a range oven and then around 5 to 7 years the control board blows out and costs another $500.00 to replace plus a service agents fee to remove and install.I asked the Whirlpool agent if I could get the control board discounted and she refused and said, “I am sorry, we are unable to help you.” Pathetic! Their cost on these boards is around $120.00 or so. I was told by an appliance service rep they could discount that $500.00 board even half and still make a decent profit. Do not ever buy Whirlpool. Go with other brands instead. Their customer service policies are horrible. Your hard-earned money will be buying an appliance with a 6 to 7-year shelf life before major repairs.

My boyfriend and I purchase a Whirlpool Cabrio Washer and Dryer on November 28, 2010 from Lowes in Shepherdsville, KY. Just after we purchased the set, I read some bad online reviews of the set. I called Lowes and talked to Chris ** in appliances and he assured me that this was a good set and that it was very popular with their customers. He assured me that if there were any problems that Lowes would make sure they did everything they could to fix and/or replace the appliance(s). My intention was to cancel the order when I called, but he convinced me not to, now I completely regret not canceling that order that day.In May of 2011 we called Lowes to report that the dryer was not working properly; they sent a repair person from Maytag Service Co, 1500 South Shelby, Louisville, KY 40217, phone number 502-637-6526. The name on the card that the repair person left is Steve **. The repair tech indicated that the problem was that the belt had come off and he put the belt back on the dryer. It has worked without issue until about 2 weeks ago, when it stopped drying again. I assume the belt is off again since it is performing exactly the same as it did in May when we had the repair company out.I called Maytag Service Co approximately 1 to 1 1/2 weeks ago to see when a tech could come back out and I was told they only work Monday - Friday. I told them both my boyfriend and I work and cant really take time off from work to be home for the repair. The male on the phone indicated that they could call 30 minutes before arriving if that would help. I told them that wouldnt really help since I work in Louisville (about 30 minutes from Shepherdsville where we live). He indicated that was the best they could do.Yesterday, November 7th sometime during business hours. I spoke with someone in their appliance department. He indicated that I would need to call Maytag Service Co at 502-637-6526. I called them and was advised that they could come out the next day (today), November 8th, but they could not give me a time window. I spoke to a female who did not identify herself. She specifically stated, If someone has not called you by 8:30 a.m., you can call us and we will give you a time window. Since I had just earned a vacation day at work, I so desperately need my dryer working that I took the day off to get the dryer fixed. I got up at 7:30 a.m. this morning to prepare for the service call. I have not left the house today. At 9:20 a.m. my boyfriend called and said that the service company had called and they were not coming out. I called them back and again spoke to an unidentified female. She indicated that they called my boyfriends phone at 9:00 a.m., he called them back at 9:20 a.m. I was on the phone with the female at 9:25 a.m. She indicated that I should have called at 8:30 a.m. and that they never call their customers because they dont have time to call them all. She said that when my boyfriend didnt answer the phone at 9:00 a.m., they had to send their tech on to the next call because, they cant have their tech waiting around 20 - 30 minutes on customers to answer their phone. When I told her that I took my only vacation day to be home for this call, she indicated that I would have to reschedule for another day because their tech was already on his way to another city. I then stated that I thought that was ** and she hung up on me.I called and spoke with the store manager at Lowes in Shepherdsville, KY. He called Maytag Service Co and was told that I used profanity and was rude and that I would not provide them with an alternate number. Most if not all of these are lies. I did say **, but I was not rude and I was never asked for an alternate number. I give out my number and my boyfriends number to almost any company we deal with. My boyfriend is also a service technician for Icee Corporation and he is not allowed to be on a cell phone in his work truck; therefore I always give both numbers since I can easily answer the phone throughout the day. The store manager made several attempts to try to find another company to come out and service our dryer, but cannot find anyone to come before tomorrow. Since I used my only vacation day today, I cannot be here for the technician and my boyfriend doesnt have any vacation or sick time to take to be home for the call.I cannot believe that after spending over $1300 on a Whirlpool Washer and Dryer set (including several hundred dollars for the extended warranty), that we cannot get our dryer serviced at our convenience. Since when did companies only repair or back up their products at their convenience? This in my opinion is the worst customer service I have ever seen. I thought Whirlpool/Maytag was a good company; now Im not so sure. I just wish I could return the set and do more research and find a quality appliance that wont break down 2 times in less than a year!!

Purchased this Upright freezer model 160NZTQ02 approximately 2 years ago. Freezer had problems maintaining temperature from the beginning. Noticed it freezing up at air vents in back of interior. Unplugged, removed contents, and let defrost by ambient temperature (approximately 4 hours). After using this method for first three defrost periods (approximately two weeks apart) I began defrosted with hair dryer, then moved on to heat gun. Bottom line is this junk wont hold temperature and freezes up every few days to a week. No more Whirpool for me.

We have several Whirlpool products in our home currently and have been very satisfied with their performances. We have their fridge, stove/oven, microwave and dishwasher, all of various ages. We purchased them from a local big box building supply company and installed them our self. The installation directions are clear and simply for the average D-I-Yer. We would recommend Whirlpool to everyone shopping for these home appliances.

Have owned my Whirlpool washer model# LSR 701 0PQ1 two years and had no problems with it before today... The washer was used once a week since I purchased it and only myself use it. There is only myself and my son and our loads are always small. Well today I put a load in and went to finish my other housework and when I went to check on the load, there was a weird smell in my laundry room. As I approach the washer to put softener in the rinse I saw a flash behind on the left hand side of the control panel where the size of load and water temperature selection is. I unplugged the washer and put the fire out. Have never had anything happen like this before with this brand. I already know I have to buy another washer but am scared to get another Whirlpool.

Weve had our Whirlpool Cabrio washing machine for about 3 1/2 to 4 years. At first, it left our clothes wrinkled, so I purchased a steamer to help remove the wrinkles. After a few months, it started making a terrible clanging noise. My husband was able to repair and it ran okay for a while. Over a few months, it got louder and louder. It does not get our clothes completely clean. Some even come out dry on one side. Now, we are getting an F50 code and it shuts down after 1 minute. After reading the reviews, I agree Cabrio is a bad product. What happened to the trustworthy, best value Whirlpool name?

We bought the dishwasher because ours was not a very good quality, and it was a Whirlpool and was larger than our old one. But the arrangement of the bottom shelf doesnt allow for effective placement of larger items. If you wash any large items it doesnt wash the top shelf dishes.

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

After only two and a half years, my Whirlpool bottom freezer refrigerator (GB2SHDXTQ0) was frosting over and the top food section stopped working altogether. I made a call to Lowe’s. It’s not their problem. I then called Whirlpool and he said I had a bad gasket. I had a 28-year-old refrigerator that was still working with the original gasket and it has no problem. After reading all the complaints with Whirlpool, I would never buy another one again. After cleaning out the refrigerator and freezer two times, carrying things to a friend’s house and having to pay $90 service calls just to walk into the door, I am ready to throw this one out. This refrigerator cost me $1200 and I am a single person living on $900 a month. Thanks for nothing, Whirlpool. There should be a class action suit.

I bought a new whirlpool washer 12/15. In May 2016 it stopped spinning fast, clothes are coming out wet, still waiting for it to be repaired. Waited 3 weeks for a part, repairman came out today, it did not fix the problem. Now it doesnt work at all. Service tech said wait another week for more information. Called whirlpool. They offered me a $50 gift card to cover the laundromat. I paid $1200 for this washer. whirlpool doesnt care. I want a replacement. They said the warranty covers repair only, but they cant fix it.

My water heater was installed in 2007 (model BFG2J5040T3NOV). It has required 3 repairs in 4 years because part failures make the pilot light shut off. The gas controller was replaced in 2008. The manifold/burner assembly was replaced in 2010. This month (August 2011), I have replaced the thermocouple, which did not fix the problem. Now I am having to replace the gas controller again. The part is failing, but not completely inoperable, so occasionally when on the phone with customer support, the pilot light would stay lit. When this happened, the tech would act as if the problem was solved and tell me to call back if the pilot light went out again. The next day, the pilot light would go out again. Thus, I have spent several hours on the phone with customer support running the same tests and answering the same questions over and over again.

We just remodeled our kitchen and bought a Whirlpool kitchen suite in May of 2016. The refrigerator is absolutely terrible. I have had a repairman come out and fix the same repair/problem 5 times, a sheet of ice forms beneath the vegetable drawer (We have only owned the refrigerator for 5 months). Each time the repair person has come out it costs me a day of work due to having to wait all day for the repair service that Whirlpool hires out, well be there between 9am and 4pm. This morning I decided to check to see if the sheet of ice is forming again, it is. So I call Whirlpool again.Again, I call Whirlpool and ask if I can just get a new unit; 5 repairs in 5 months on a brand new refrigerator. The reply I get from Whirlpool is always well send someone out to fix it. The unit has to be deemed irreparable or a part has to be replaced multiple times. No parts are being replaced... no one knows how to fix it. I dont understand why a large company like Whirlpool would want people to write bad reviews for their products and customer service. Im extremely irritated with how I have been treated. I just want a refrigerator that works!! DO NOT BUY A WHIRLPOOL REFRIGERATOR!!

I bought a brand new Whirlpool washer and dryer. The Whirlpool Cabrio washer does not clean my clothes no matter what size load you have. I have tried every combination possible to get my clothes clean and 95% of the time there are clothes that don’t even get wet let alone clean! I have only owned this washer since July 22, 2018 and am now willing to give it away - that’s how upset and displeased I am with it! If you read reviews, stay away from this model - not good!

I am done with Whirlpool. Everything I have bought is failing. I bought all new appliances when moving into my home. Dishwasher, 2.5 years old, quit. Cost is going to be as much as a new one. Refrigerator quit at 5 years old, what a mess that was. Paint is peeling off my clothes washer. I am not going to buy or recommend any more of this junk.

I purchased the GBS309PVS single oven in Dec. 09 along with a Whirlpool Gold microwave, dishwasher, and stove top. The oven was dented and scratched, so another one was delivered on 1/10/10. I finally decided to use the cleaning cycle in Oct. 10. It burned out the circuit board and something else. It was under warranty and repaired. I was afraid to use it again, but tried it yesterday, 12/27/2011. It smelled horrible, knocked the power out of the oven, and the door will not unlock. Customer service was not very kind and said that I had to purchase a $269 warranty and they would send someone out. I did, unwillingly. Well see what happens on Friday. If this is not resolved, I will go further. This is a faulty part of the manufacturing and should be handled as so.

I hope the CEO posts this on a giant screen in front of all their employees. The first thing I did after moving into our new home is brag about the American made Whirlpool appliances. Being from the Midwest I take pride in made in the USA product and go out of my way to support homegrown companies. I know that a number of the components in my fridge include the fan that failed after 11 month were most likely sourced and manufactured in China... but that no excuse!! Whirlpool needs to do a better job of QC. You need to be passionate and rigorous with your testing. Dont reduce cost at the cost of your customer base. It is amazing were to the point where we can no longer compete with China in quality.Second is customer service, if you know you cant compete in quality you need to be able to make up for that with customer support. I called Whirlpool and scheduled an appointment the day the fridge quit working. I was upset that it would take three days to have a working fridge but I was understanding. Lucky for me I had an understanding neighbor too. Anyways, when the day came for my scheduled warranty repair I was told that Whirlpool was mistaken and that I wouldnt be able to get it serviced for another week! This is just unacceptable.Right away I called the Whirlpool customer service representative and manager to express my frustration with this error. They were polite and both agreed with my frustration. It also sounded as if they also didnt understand why their own company was doing such a poor job addressing repair issues. They made it sound like this was a common problem of people getting overbook at repair service providers. Again another fumble. Bottom line, due to my position, I dont really have a choice but to wait another week for a repair. Take note: Every time you lose a customer like me this you lose 10! I will now go out of my way to tell people about my negative experience rather than my positive. So disappointed.

Ive had my Whirlpool water heater for almost 4 years now and for the last year and a half, I had to have the pilot light lit at least 5 times. I finally got so frustrated around the 3 times and called the company. They gave me instructions on how to light it and to ensure no draft was around the tank. A couple of weeks ago, it went out again and I called. This time I was told to replace the thermocouple. I did that and guess what? Still no hot water. Im a single parent with 2 kids and weve been boiling water just to bath.A service tech came out and told me I need to replace the tank altogether. I called Whirlpool service and they told me it was nothing they can do. Like many of you, I got this tank from Lowes and they will not do anything about it either. Its hurtful and stressful that doing a holiday season, I have to decide to either buy a hot water tank or give my kids a good Christmas. I know several friends and family who has had their tanks a lot longer with no problem. My problem is its a crappy Whirlpool brand with poor customer service.

We bought a Whirlpool front load about six years ago. We have had nothing but trouble with since we have owned it. First, the sensors went out on it. We had to pay over $300 to have that fixed. Then, it wouldnt run right. We had to pay another charge for that. Now they tell me the water valve is bad on it. If I had known at the time the problems I was going to experience with this washer, I would never have bought it. I fell for the price. We paid for it. We should be getting better service from it than we are. I could have bought 6 regular washers for what I paid for this one that doesnt perform like it should.

You cannot control anything on this machine. You cannot pre-fill to dilute detergent- you cannot choose temp because what you choose is changed by the machine (manual). You cannot choose your own combinations of temp, water volume, and timing. Once the ** thing starts you cant change anything, like the setting you wish to use. Do NOT BELIEVE THIS IS ENERGY EFFICIENT. There is a REASON that this machine has a 2nd rinse. It is because so little water is used that it does not allow soap, lint or dirt to have anywhere to go but back into your clothes. YOU have to trick it out to get enough water to actually get some loads truly wet. EVER! You stand there like an idiot opening and closing the lid just to get enough water to dilute the detergent. You cant pre fill and then add your detergent because, it needs to sense your clothes load. Wont fill with the lid open. You cant rinse the detergent cup out. You only get to do what Whirlpool already knows about your needs. Oh & lets not forget the spin cycle. When you open the lid, large items like sheets will look like a pancake made from one of the sheets. However underneath will be a tangle of the rest of your wash worthy of a Gordian knot. You can yank your shoulders out trying to dislodge the clothes. Spin yes, I guess it did, I just didnt need permanent press wrinkles. And thats if you CAN actually open the lid. For some idiopathic reason the lid may be on lock. Good luck with that. Most often, youll find no reason that you can discern like an unbalanced load or as the booklet suggests, you havent figured out how to load a machine. I hate the design of this so much that I called the company and they said that they would send a repair man out to see if its working. Whats he going to do? Run a couple of washes and say hey thats how they design these things? They will not replace it. They do not stand behind their products. You are stuck with bad design period.Describe Yourself: Frequent User. Service/Delivery: It came with a big dent in the dryer we bought with it. Installer dudes crossed the hot with the cold. Whirlpool will not stand behind the products they make & they make lots of the brand names. So they figure they can just do exactly what they want and youre screwed because even under warranty, theyll only fix the mess of engineering they designed in the first place. Bottom Line: No, I would not recommend this to a friend.

Got a simple error code E6 F2 on the display of my oven (only 8 years old). Called Whirlpool to schedule a repair. They told me there were no available dates for one of their techs to fix my unit. They referred me to 3 outside companies that wanted to charge me over $100 just to come out and take a look. One of the phone numbers to the companies they referred me to was a wrong number. I asked them to tell me what the error code means and they said they couldnt tell me with any degree of accuracy. (What use is an error code, then??!!) I checked all over the internet and different websites say it might be a control board (over $300 for the part) issue. But several techs also said that it is a crap shoot and could also be a Temperature Sensor. I called back Whirlpool to see if they could get me a deal on the part. But, guess what? They dont sell it anymore...in fact they dont even sell their own parts at all!! And, they transferred me to some outside company that refused to even give me part numbers, to avoid me shopping for a better deal (which I did end up finding on Amazon after number 6 below). I called back Whirlpool and after getting transferred around to 2-3 different people and wasting about an hour I finally got someone who finally wanted to just give me whatever decent service they could and they finally got me the part numbers of the 2 different control boards (Main Control Unit and Sister board that controls the locking mechanism, $367 and $140 respectively). Now I am faced with paying an Appliance Repair person over $500 for what seems to me is a BIG FAT LEMON of an appliance due to the sheer number of unsatisfied people that are having the same issue, have had it fixed, and had the error just return again. THUS.... WHIRLPOOL AND THEIR CUSTOMER SERVICE AND THEIR PRODUCTS JUST SUCK!! AND I WOULD NOT RECOMMEND THEM TO ANYONE! THE LEAST THEIR COMPANY COULD DO IS TRY TO HELP FIX THE PROBLEM, NOT EXACERBATE IT BY GIVING SHADY CUSTOMER SERVICE AND REFUSING TO HELP FIX THE PROBLEM!!!

I was searching online and stumbled across this site. Funny that there were so many complaints about the console on the ovens, considering that my issue was with the console on a dryer I purchased. I have only had the dryer a year, and it stopped working. There is nothing else wrong with it, no codes, no problems with the lights, or anything else. A technician came out and found that it was a small plastic and metal button piece that helps the press here: spot on the dryer panel to connect to the start button on the console. The little arm had broken and the switch no longer worked.Figured we would have to purchase a new button. NOPE, apparently we were told that we had to purchase a new console (over $200 dollars, close to $300 with shipping)???!!! We were also told that wear and tear can cause the issue. Wear and tear?? On a dryer thats maybe run once a week for about a year? Try again, I think I need my boots because it sounds like horse** to me. I think I will pass this information along to people I know that are technicians so that they can let people know not to purchase from this company because they obviously arent going to address the situation. I think I might also utilize social media to let people know so that they dont have to go through this much aggravation. I certainly dont know what we are going to do, since it took me a year to pay that dryer off, I cant afford another dryer at this time. So unfortunately with a new baby on the way, you wont get any sympathy from me if your company takes a character hit.

First of all, Whirlpool is fully aware of the problems with water heaters and intentionally places requirements on the consumer until they give up. This info from a distributor. I bought 30 gal. gas water heater 7 months ago. Six days ago the pilot light went out. Went to Lowes (purchased there) and bought a replacement. Wrong one. Returned to store and was told they dont stock repair parts, call factory. Monday called warranty number. They offers to send thermopile, it would arrive in 5 days. I paid $30 for overnight. Plumber installed new part. Still doesnt work. Whirlpool says have the plumber call them theyll walk him through troubleshooting. I ask, Whos paying the plumber? They reply, You are. Plumber calls Whirlpool. They tell him to clean the screen. He does. They tell him to disassemble the burner. I stop plumber. I ask Whirlpool, What if its not the burner? They reply, Then well troubleshoot something else. Meanwhile Im 5 days without hot water. I go to Lowes where heater was purchased. The manager thought it funny Im another victim. I ask, Why doesnt Lowes stock heater parts? He says because Whirlpool doesnt let them carry parts. Im beat. I surrender. Parts from Whirlpool would take another 5 days and theres no assurance itll work. Lowes refuses to assist.I go to Sutherlands and buy a $450 Rheem on recommendation from plumber. Manager from Sutherlands hears my sad story and writes on receipt: Any warranty failure and Sutherlands will replace water heater free. He signs his name on receipt. I pay plumber to swap out heaters. Anybody want a 7 month old Whirlpool water heater. Like new. Cheap! By the way... I originally went to a major appliance parts store asking for a thermocouple for a Whirlpool. The three guys at the counter started laughing Hey we got another one looking for Whirlpool parts. They didnt have them either. Lesson learned.

I bought this Whirlpool Duet Sport washer and dryer, and I have had to constantly bleach out because our laundry smells like mold. I found out that Tide sells a special cleanser for this washer so I have been using that for the past two years. It did not really help. Well, today I accidentally put laundry soap in the wrong dispenser, so I took the dispenser out and was horrified to find mold that was all in the back where the fluid is dispensed, I mean way back in there. I have been suffering with sinus problems, and swelling in my eyes and face. I even went to the doctor, but no one has figured out why. I now know it is the mold from my washer making me sick. Well, my son and daughter-in-law were staying with me, and commented on how bad it was when they used my towels. I am stuck with a $1,600 washer and dryer that is making my family sick.

I purchased the hot water tank from Lowes 3 years for over $500.00 within the first year, I experienced issues. I have the same pilot light problems as everybody else. I have hired a plumber four or 5 times to clean and blow everything out as instructed by Whirlpool. The hot water heater will not stay lit. The plumber has replaced every part possible two times. Customer service continues to inform me to do this and that and everything has already been done. I am without hot water again with children in the house. Once again, we are boiling hot water so that we can bathe--total inconvenience. This product is defective, and has cost me money to hire a plumber each time. I would never recommend this product to anyone!

Oh my goodness, are these people right with the Whirlpool Ranges. I moved and put in the appliance # to get what I had from Whirlpool. What a piece of crap I got in a range and refrigerator. Never had appliances that looked so pathetic. You cant clean the outsides or the insides. Outsides nothing but streaks never look shiny, I really do doubt they are even close to Stainless steel. My old ones I might add were less than 5 years old when we sold our house and all you had to do was spray with Windex and shine shine shine. Try that on the new ones streak streak streak, and nothing ticks me off more than looking in a kitchen and looks like pigs are running all over your stuff. Then the range aqua lift self clean. You have gotta be kidding. No self clean about it. Scrub Scrub Scrub by hand. You mean who in the hell came up with this. Make something with fat and instant burned mess. Really oil and water or grease and water where I come from they never mixed, and all they do is get gummy. Now if you dont care how your oven or outsides look then I guess it doesnt matter BUT I DO, I am with the guy that said he just wants to throw it out. I would have been better off buying a clean your own. At least you could use oven cleaner. I dont know where these companies are coming from ripping people off this bad, now that I am older I am stuck with it and can hardly clean it to get down in there. You make supper and you have to spend 2 hours extra in the kitchen scrubbing the damn thing. Of course you give a company loyalty and get screwed this bad. All my self cleaning ovens I had when we sold houses the people thought you never cooked in them. This is not even a year and a half old and looks like it is 10 years old. Even scrubbing it is a joke. You cant get it all anyway. Im sure I will not live with this long. I use to love to cook even did it for a living and man using this thing I hate cooking more than ever.

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

The washer constantly binds clothes around agitator. Truly a design flaw and it does not get clothes clean. So with a washer like this, I am forced to go to laundromat. Wished I would have paid 230.00 or so to have transmission fixed on old Kenmore. Truly dislike this substandard appliance.

I dont know the model you have but this exactly what I just had happen in May. Its what they call the jazz board that is behind the light area inside the front of the refrigerator, where the light bulb goes. This is a circuit board and it seems when connection arent happening properly the fridge wont go into defrost mode and the water freezes over the evaporator not allowing any cold air to the top but working cooling freezer and making lots of frost too. I paid $400 to Sears service repair. The jazz board itself, I kept the old one and you can buy it online for about $100 and a child can do the labor that I paid hundreds for because, like you, I didnt know what the problem was. It takes less than 1 min to do this. I was furious! I hope this helps you and I too will never buy a Whirlpool. I found this site looking for why the refrigerator is making very loud noises, very loud banging, clicking, humming. Its ridiculous!

When you purchase a Cabrio high efficiency washer dont expect clean clothes! But, you can expect holes, torn and, smelly clothes. It takes a ridiculous amount of time to wash. The machine I purchased has a glass top but its dark and you cant see into the machine so that was a waste of money! If you wash clothes in 1/4 depth of water, nothing gets clean. Who even designed this disaster? I had enough common sense to know it was going to be bad but the salesman at Lowes informed me that ALL washers were high-efficiency and getting a tub full of water days are over. I wish we wouldve just paid for repair and kept my old washer. I hate doing laundry with this machine! I use to be able to wash my blankets, pillows, curtains, throw rugs, even car mats with no problems. Not anymore! This machine couldnt handle it. You ought to see my sheets and shirts when theyre done. They come out twisted up so tight I have to untangle them before they go to dryer. What a horrible nightmare of a machine! If we were not out so much money Id send this machine to the junkyard and get a real washer with realistic amounts of water! How are you saving anything when clothes require 2 times to get somewhat clean??? If youre reading this and considering a high-efficiency washing machine, DONT DO IT!! You will regret it. Im counting the days when I can junk mine!

Purchased a Whirlpool top loading washer. The agitation cycle is unreasonably loud. So loud you can hear it everywhere in my home and cannot have a conversation within about 30 feet of it. When I ran it for the first time I thought it was malfunctioning and when I called Whirlpool I thought they would send a technician to fix the problem but they told me that the sound was perfectly normal for high efficiency washers! My other high efficiency washers were very quiet. The fact that they think this type of noise is not only normal but quite acceptable makes me quite certain to never buy any of their products again. Very disappointed to see what once was a quality company to be so lame.

BFG2F4040T3NIV IS HORRIBLE. This water heater is JUNK. The release valve has released and flooded my basement 3 times in the past 2 years and the recovery time on water is terrible. Whirlpool needs to step up to the plate and refund everyone who purchased one of these. Every review on this unit is horrible. DO NOT PURCHASE a WHIRLPOOL water heater!

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

I purchased a Whirlpool Cabrio just over a year ago. The washing machine does not clean clothes! While under warranty, a service tech came out to look at it. After hearing the problem, he replied that it was a common complaint and that he could not fix the machine because the problem was that it is so poorly made that it simply does not work. His recommendation was to come to terms with the loss of a thousand dollars as Whirlpool would not rectify the problem.Whirlpool really showed their true colors when they refused to cover the repair tech visit. Whirlpool supervisor Kitty explained to me that customer advice was not covered under warranty and that we would have to pay the bill. Highlights of her argument were that we should just rinse the clothes multiple times and they would eventually get clean. She also mentioned that if the machine really did not work as described, we should have complained sooner even though it was still under the one-year warranty. Whirlpool will sell you junk backed with horrible customer service. Beware!

After owning the highly recommended Cabrio for only 2 years, I was told it would cost $300 for the motherboard!! I have always used Whirlpool but this machine is terrible. Water saving is not an option when washing clothes. Unless I use the bulky cycle, my clothes come out dry and smell dirty.

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

I am an apartment manager. We purchased a Whirlpool Refrigerator (Refrigerator FFHT1817LW8) for one of our apartments. When it arrived it was missing a shelf next to the butter dish, also two of the bars that were to go in front of the shelves were the wrong size. This was at the beginning of April, it is now the second week of July and I am still dealing with this issue. The 1st company that was sent out to take care of the problem, A&E appliance, dropped my call so many times I ended up refusing to deal with them anymore. They also sent techs out 2 different times, and both times the wrong parts were ordered. Finally a different company was sent out and they told me that there was nothing that they could do, the shelf did not exist, even though the paperwork that came with the fridge showed a shelf next to the butter dish. Finally Whirlpool offered to order a whole new door but this would take 6 to 8 weeks...I had already been dealing with this issue for over a month. Home Depot stepped up and replaced the fridge; however, when the new fridge arrived it had the exact same issue, no shelf next to the butter dish. That fridge was returned and we ended up getting a completely different model. I canceled the door order with Whirlpool twice! It was supposed to be sent to Home Depot; however, Whirlpool still shipped it to our complex, and to a completely different apartment! It has now been going on 2 weeks almost 3 and the door has not been picked up yet! Despite my repeated calls into the company... I have asked to speak with a supervisor and was told that I couldnt. I have asked to be transferred to and escalated department or complaint department, I was told that I couldnt. There was a phone number I could call to give a compliment to.... LOL!! I would compliment them on their ability to provide the worst service I have ever experienced in my life! I was told a supervisor would be contacting me within 48 business hours, they havent. I have been told that they sent an email in a RED folder to their escalation department and that is all that they can do.... still havent heard anything.... seriously? I have now advised my company to no longer purchase any Whirlpool products... and its funny because we are going to be remodeling all of our units soon and that includes appliances... I have also shared my horror story on Facebook. Maybe as they are going bankrupt they will start to care??? Somehow I doubt it!

Mine came new with the home I purchased 3 years ago and so far I have had no problems at all. The only drawback is that if it is on, you can hardly tell it is running so if you forget you might interrupt the wash cycle unintentionally. It does an excellent job on dishes and the stainless steel front is easy to keep clean since there are no mechanical knobs or switches, you can just wipe it down and be done in less than a minute.

My 5-year-old Cabrio started coming up with error codes, and not draining and spinning the clothes. I called a week ago, they offered me 2 options, one being put $339 on a credit card and that would cover all parts, labor, and a 1 year extended warranty. They charged the credit card immediately for the biggest piece of crap washing machine. Someone came out 2 days later and told me he has worked on a lot of Cabrios but never one in quite that condition. I was led to believe that after charging the credit card, boxes would be arriving with parts to fix it. I called 2 days later to find out the status of when it would be repaired and they told me they already put a credit thru on the credit card because to fix it would be equal to the price of 2 brand new washing machines, and they will do nothing to honor that agreement. So I now have a piece of ** in my laundry room and takes me two days to do a load of laundry. DO NOT BUY THE CABRIO! In fact Im not going with a Whirlpool ever again!

I bought a Whirlpool wdf760sadmo. It was Oct 2014. It broke 31 days later. Lowes said they would not take it back. Called Whirlpool, they sent a repairman out a week later. They ordered parts and came back two weeks later. The parts were not the correct ones. Ordered more parts. This time back in a week. Ok about three weeks have gone by with a broken dishwasher sitting at my house. Got it fixed. A month later a different problem. Call Whirlpool, wait, on hold for about 20 or 30 minutes. They sent a repairman out who ordered more parts which will be in in two weeks. Meanwhile I am without a dishwasher again. I have had to take a day off work each time they have came to repair it. I have spent way too much time on this thing. I wont be buying another Whirlpool.

I have had this unit less than a year and started having pilot problems. I would just relight and ask family members to take shorter showers or not run the washing machine or dishwasher at the same time. I would have to relight the pilot 3-4 times a year and would just tolerate. Now the water heater fails on a daily basis. In the last four weeks, my wife would say NO HOT WATER AGAIN. I am so tired of dealing with this, so last night, I called Whirlpool and associate was polite but gave me a lot of things that I should do (43 yrs a pipefitter). Before all was said and done, he is shipping me a new gas valve (at my expense) that I will gladly install to get rid of this problem. Will not EVER buy a hot water heater from Whirpool or Lowes ever again. Whirpool should stick to washing machines!

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

It is a top of the line washing machine. I have had it for almost four years. It is the best washing machine I have ever had. I have really enjoyed it, because; I am able to wash my comforters in this washing machine.

Ice maker continuously freezes up & have to pour hot water into the ice maker to get the ice maker off the mounting. VERY ANNOYING, A DEFECT IN THE UNIT= NEED CLASS ACTION LAWSUIT ON THIS.

Over-the-range microwave hood combo - It is not that it does not work, it just wont shut off! Close the door, it turns on. Touch the side, it turns on. I have walked in the kitchen and found it on! I am afraid it will turn on when I am not home and burn down my house! After reading the poor customer service received by others, I will just replace it.

Reading the reviews on this I figured I would chime in. Same problem with the top rack, its unfathomable how cheap this was constructed, since I have had old school dishwashers 15 years old without even close to a similar problem. Bought in 2012/2013 and have had this problem on and off the entire time. Looking at a new one definitely not a Whirlpool!

The Whirlpool range #GY398LXPQ00 is four years old. This is the fourth major problem. Oven overheats and will not function. I set it at 350 and the bottom coil and broiler both came on and overheat quickly. This is the third time with same problem. I am going to have enough invested in repairs to buy another range. I shall never purchase another item made by Whirlpool or any of its affiliates. That leaves me with Samsung or Bosch, I think. The people are very curt and offered no help at all so calling them is extremely useless. This range is definitely a lemon. Too bad, there arent avenues to make them replace it. I am angry, disappointed, and disgusted. Are you listening, Whirlpool? Never again. May your company go down the drain.

My Whirlpool washer is lasted 15 yrs and is very good at cleaning clothes, it is also easy join my water bill. I purchased mine at Home Depot. They also finance. I hope you enjoy your purchase. I know I do.

We have had every issue with our Cabrio model 6600 SB2 that Kimber of Salem, VA has had. Thankfully, we purchased an extended warranty at time of purchase(1-31-07) from Lowes or repair costs would have totaled more that the price of the washer, which was $900.00.It is now making a loud noise during spin cycle that sounds like a bearing going out. It is 1 month from being out of the 4 year extended warranty and today, 12-26-11, the repairman has told me that the washer needs to be rebuilt. The washer itself, does not clean that well and the clothes are so wrinkled when they come out, that the dryer cannot get the wrinkles out, so everything needs to be ironed. What a pain!We bought this washer because Consumer Reports magazine listed it as a best buy. This is not the first recommendation Ive chosen because of their magazine that I was disappointed with. I have lost faith in them. I would not recommend this washer to anyone. The matching dryer, however, has been trouble free.

We purchased the Whirlpool washer less than a year ago and are now having the 4th transmission put into it. We are also having the 3rd timer put into it. We purchased this from Sears and bought the extended warranty (thank God). One of the times the technician ordered the parts to repair the machine. The service center sent the wrong parts and we had to wait an additional week for the correct parts to arrive. The 3rd transmission they installed lasted a week before it leaked gear oil all over our floor. When you do get a service call scheduled it will get rescheduled to a later date. This happened twice. They also cancelled the service call once before they fixed the machine. If I could give a zero star for this I would. DO YOURSELF A FAVOR AND DO NOT BUY A WHIRLPOOL WASHER AND DO NOT I REPEAT DO NOT GO TO SEARS FOR ANYTHING. Worst company to business with. I will say this that the service guy that comes out to do the work is a good guy. He stayed until almost 9:00 pm on one of the service calls. Hes been here so many times our dog knows him and doesnt bark at him anymore.

2 yrs after my landlord installed WHM31017AW1... Whirlpool oven stove microwave. The door cracked then another crack and pieces from door fell on stove. I removed all loose pieces then glued all cracks & loose pieces on door. Landlord thought door was being closed too hard, silly. After all reviews same, not buying replacement door but having different brand installed.

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.

WRF989SDAM00 - We spent about $1800 on a Whirlpool French Door refrigerator and at 1.5 years we had to replace the compressor for $700+. Apparently Whirlpool will only warranty for 1 year. The repairman told me the compressor he was putting in is exactly the same model as the bad one he took out so I guess I am not surprised that it only has a 1.5 year working range. We are now 1.5 years into the new compressor and sure enough it is dying again. Now it sounds like a jet plane taking off. By the time I replace it again I could have bought a new refrigerator. I am trying to figure out if this refrigerator is on recall because I cant keep replacing the compressor every 1.5 year. Never again will I purchase a Whirlpool product. I think they know the lifespan of that compressor and that is why the warranty falls just short of it!!

We purchased our Cabrio washer and dryer in 2012. In 2014 we had to replace the rollers in the dryer. Since then it makes a loud clunking sound and it has to go through at least 2 or 3 dry cycles to dry the clothes, sometimes more. The washer lid lock doesnt work very well anymore. Sometimes it wont lock so I cant get the clothes washed. It takes forever to get it to work. Ill never buy Whirlpool again.

This washer started out to be good. Its only 5 yrs old. We began to smell an odor. Went to Lowes, spoke with someone in appliance dept. Purchased something for washer. DID NOT WORK. We have tried bleach everything. Our clothes smell. I have skin rashes and I think it is related to mold and mildew. Called the service center. They said could be a sock stuck around the tub area. They need to recall this washer. We spent a lot of money and it has ruined everything. Cannot get the odor out. We cannot afford another one. There is black mold around the rubber lining when you open up the door.

Wife and I bought a WRF990SLAM00 fridge in 5/2013. Seemed like the nicest model Lowes had at the time. The first one delivered had problems: it wouldnt stand level or seal properly, and had to be replaced. Another unit was delivered a few days later. This one - the same model - worked very nicely, for a year and a half. A few days ago, it got loud. My wife noticed in the freezer, some things were beginning to thaw. We called Whirlpool, who said, Oh, its over a year, and youre out of warranty. Sorry! Ok, so they suck. After we had a technician examine the freezer, he suggested, This is something Whirlpool needs to address. It wasnt the first (or fourth) problem with this fridge that hes seen. Called Whirlpool again, this time to gripe. Sorry, youre more than a year, so no warranty BUT, well sell you a service contract for $330! Hows that sound? It sounds like Whirlpool just disqualified themselves from ever getting their hands on another dollar from my family. Theres too many other companies who DONT treat their customers like garbage.

My Whirlpool Cabrio cannot wash sheets, blankets or any of this size. It balls up in the middle and form a bubble and only part of the items is washed and washing powders are trapped. I have purchased more sheets in the past 4 years than I have in the past 45 years of doing laundry, because the washing powders are not washed out. I wash on second rinse also, never fails and it still does not get all of it out. The clothing gets off balance if it was more than 3 small items. I have a leveling tool that I put on it often to make sure it is level. It’s something within the machine. I will never, never, never purchase any more Sears’ product. If anyone has jury-rigged this machine to work, please let me know. Sears has refused to help me, even today.

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

We purchased our Whirlpool Refrigerator #WRT519SZDB from the Home Depot 2 years and 10 Months ago. About three weeks ago it started to freeze items in the frig section. We lowered the frig section cooling level one selection and went on a two week vacation. When we came back, everything in the freezer section was thawed out. We had a tech look at it and he told us that the compressor was partly seized and overheating. Tried to reach someone at Whirlpool customer service by phone, email, and chat but so far, I have not had anyone contact Me back? Looks like repair will cost almost as much as a replacement refrigerator. So much for Whirlpool being a trusted brand!

We purchased all our appliances from Flecks - there were to be rebates. Also never received them. We have had our oven for 2 years - when I set the oven on 350 it will go up to 400 degrees & the temperature on the front of the stove is 350 then it will drop down to as low as 250 & the temperature will still say its still 350. I called the company - did will do nothing. Will cost me as much to fix it as to get a new one. This a Whirlpool oven.

Purchased a Cabrio washer wtw5550xwo in Sept. 2010.. Had to replace the pump a little after the warranty ran out. Then recently the control board goes out. Called customer service to complain. This part costs $320 to replace. They told me since it is no longer under the one year warranty they could not help me. This is a major part in less than 5 years of the machines use. I guess I will be purchasing another washer. It will not be a Whirlpool or any company affiliated with them. How sad. I would not recommend Whirlpool to anyone. They just dont make them or stand behind them like they used to.

Purchased first water heater in 2008 with 6 year warranty. In 2011, pilot light would not stay lit. Whirlpool told me to go to Lowes and get a new one at no cost. But I had to pay for service to identify the problem and installation of new one, costing $250.00. A year and a half later on a six year warranty, the same issue the pilot light not staying lit. They send a pilot light assembly and we pay the shipping and installation cost of $130.00.Two years later, the same issue begins again. Calling tech support, they determine it needs a third pilot assembly at $30.00 for shipping and $265.00 service installation fee by a certified Whirlpool technician. Worked one day! Im so done with this company!!!! I was promised a call from a supervisor with Whirlpool which Im still waiting on days later. Probably for the best at this point. I think I would feel better if I could beat the crap out of a Whirlpool CEO with it! Im cutting my losses and going with a different provider. I will NEVER again purchase another Whirlpool product!

Bought this washer NEW 4 yrs ago. Now sounds like a freight train in the house when in use. Whirlpool customer service is absolutely USELESS!!! They do not stand behind their product and refuse to acknowledge what is a common issue. PISS POOR and will NOT give me a number to a higher up. Absolute disgrace!!!UPDATED ON 10/28/2015: This is an update to my previous review. 1st, I contacted Whirlpool who was absolutely NO help whatsoever and the person I spoke to refused to put me through to higher ups on the food chain. I was wrong in my previous review when I stated that we purchased the washer & dryer 4 yrs ago. It was purchased in January 2012. Started making noise in 2014 and has progressively turned into the sound of a freight train. I also failed to mention the stench that comes from this machine. It has also got to the point where it quits with 10 minutes to go in every wash. Whirlpool did send out a Whirlpool certified technician, which they paid for, who stated this has been a common issue with these and other models of Whirlpool Cabrio wash machines. Says in his 3 yrs with the company he has seen and diagnosed over 30 machines with basically the same issues (bearings are SHOT) and Whirlpool refuses to accept any responsibility for the defective design and that, in his opinion, they shouldve never been released. He gave me an estimate of $257.13 to repair. We decided to go ahead with the repair and technician came out only to tell me that there has been a re-work in the design of the replacement parts as Whirlpool realized they were faulty. So I now have to wait for the NEW designed replacement parts to come in as they are back ordered. WTF does that mean??? Shouldnt there be a RE-CALL and shouldnt they accept responsibility for this??? This has been, without a doubt, the most disappointment weve had with any purchase of a NEW appliance or, anything else for that matter, in our lives. After reading through some of these same complaints Im wondering if this machine is nothing, but a money pit and whats going to go wrong next. We also purchased the Cabrio dryer at the same time and have had no issues with it as of this time, but I assure you, I wait with baited breath. Their customer service department is piss poor AT BEST!! Please, stay away from ALL Whirlpool appliances in the future.

Was weary due to not a name associated with furnaces, but we installed a 100,000 Btu unit 2 stage and have not had any issues thus far.

Thirty minutes into running the oven self cleaning cycle for the first time, the middle pane of glass exploded! Weve had this range two years 4 months, and didnt buy the extended warranty. I contacted Whirlpool and they acted like this was the first theyve heard of this. I inquired on the class action law suit in New York from 2012, the year we bought ours, and they had no comment. They were willing to sell us an extended one year warranty and we pay for the service call for only $332! I declined and will never buy a Whirlpool product again.

Whirlpool washing machine model WCW4950XW2 - We have a barely two year washing machine that we purchased at Best Buy and it no longer drains or spins. After $100 repair call we were told that this is a common problem with this model. It is a transmission problem, and with the way the machine is built a repair person cannot get into the transmission to fix it. He suggested we buy a new washing machine. This is a travesty on so many levels! If whirlpool know it has a problem it should offer a partial refund for the purchase of a newer better machine. I keep thinking about what our landfill in this world look like with the proliferation of appliances that are engineered to last a year or two. I can guarantee you I will never purchase any Whirlpool produce again, and I will research whether other brands are associated with the whirlpool brand before I buy it. Sad that a once good company has gone to hell.

Absolute garbage!!! French door refrig/bottom freezer. Too much to go into. This is by far the worst product that I have EVER purchased in my life. If I was strong enough to lift this piece of ** over my head I would carry it into the corporate headquarters of these money grabbing dirt balls and throw it through the CEOs door. Amend that: I would locate customer service and consider them bowling pins. What a bummer; how far we have fallen!!!

I am very upset. I bought a Whirlpool range (model YGFE461LVS) 2 and a half years ago and today when I tried to bake a cake, the oven overheated (as if I had put it on broil) and although the display box showed that it had turned itself off, the oven kept heating and getting hotter and hotter, I had to unplug it. I feel like I have bought disposable appliances! How could I have such serious problems after only 2 years? To top it all off, this past week my fridge (also a whirlpool, model WRT779RFYM10) also started acting up. Water is leaking all over inside the fridge and the freezer. I have to clean it up everyday.

Whirlpool Water Heater FG1F4040S3NOV - I had this water heater installed in 2005 by a professional plumber and every year since like clockwork, I have to replace the gas control valve/thermostat. Last year, Sears came and did the work and made their arrangements to have the part replaced. This year 2012, March 9 my gas control valve went again. The unit is not even a year old and broke again. Unfortunately, the six-year warranty is up on the hot water tank. I called Whirlpool two times. The first time, the guy told me that the warranty was up and hung up on me! The second time, the guy would not honor the replacing of a part that is not even a year old yet. The money I spent over the six years making repair on it, I could have bought a new one. This company is nothing but a bunch of **. Is there anything that I can do? I have paid to replace this five years in a row.

Purchased a Gold Series Whirlpool dishwasher, Mo. No. WDT720PADW2, From Maruszcak in Schererville, In. on 1-29-16. Approximately a year later door was replaced by Whirlpool because of paint problem due to faulty design. Replaced door is now peeling and rusting by exhaust vent also. Contacted Whirlpool and they will do nothing more. They said it was a favor the first time they replaced the door. They feel this is a cosmetic problem! I paid a total of $675.03, Their repairman would charge a $100.00 to look at it and another $235.00 for a new door. I feel this is a design problem and they should replace it with a new model, a refund would be better. Very unlikey, because Whirlpool does not stand behind their products. The line also includes Maytag, Jenn-Air, Amana and Hot Point. Besides this I have found plastic pieces that have fallen off! I had to use plastic ties to keep them in place. Dishwasher does not clean well. Have to rinse everything first. Products are bad, stay away from them!

On Dec 18, 2015, my hot water heater located in my garage started spewing water out into my garage, driveway, and into the street. I called Lowes, whom I purchased the water heater in Jan 2011, in which it was still under warranty. I was told to call (Whirlpool) 877 817 6750, the order was placed for a gas shut out valve after going through a check system. I was then given the names of two local preferred technicians to repair water heater, whom was not available. The representative from Whirlpool (American water heater) told me I can get the plumber of my choice, authorization number was given. I had to call the (Whirlpool) (American Water Heater) back and was told the part was ordered 2 times. The first part will come on Dec 19, 2015 by UPS, and that the second part will come on Dec 21 by UPS, that a prepackaged label for return will be attached, and to tape the 2 boxes together to send back to the company--one box with the old part, and one box with the new. So, I sent the boxes to an address in Junction City, Tn. But I was not sent prepaid label, so I kept by word and spent $14. I will not be reimbursed according to American Water in which I followed their directions to a tee. So the walk away, the customer is always wrong, staff is not being trained the right way, and as a customer I am out of money and making adjustments to the way of customer service. No service. Just a waste of time, effort, and money.

I bought this stove 4 years ago from Lowes. I have had nothing but problems ever since. My family is now afraid to use the stove and Whirlpool refuses to stand behind their product. The last straw was a bill for a service call that took 6 months to complete without correcting the problem. Whirlpool sent me a bill for $100 to pay for the privileged. When I complained, WP said if I paid the invoice, they would give me a deal towards a new stove. Meanwhile, the old stove does not work and we are afraid to use it, given our experience with its reliability and safety. I plan to return it to Lowes and buy anything but a Whirlpool product. Beware of Whirlpool Maytag anything!! The customer service is shameful!!

We bought this Whirlpool Cabrio washer 2 years ago and have hated it since the first load. It does not clean clothes, and the so-called large capacity will barely clean 5 regular towels. And if you wash diapers, do not buy this washer. If a load is really dirty, you have to wash it 2 or 3 times for clothes to be clean. Then, there is the awful mildewy, moldy smell after a few washes. How can a washer that gets so bacteria-laden be allowed to be sold on the market. Ive been washing laundry for 45 years, and Ive never had this kind of wash-related problems. This washer is an overpriced nightmare. I cannot wait until I can save enough to replace it. And I am watching and hoping a class action suit comes out to force Whirlpool to take these washers back, refund the money spent, and apologize to all the people who purchased one.