I used the Whirlpool website contact form, and described an issue I have with the Cabrio washing machine. When the form is submitted, it states that the company will respond in three business days. Two weeks later, after no response, I submitted a second contact form. It has been five days, and I still have not received a response.

I purchased a Whirlpool Cabrio set 3 years ago based on their brand reputation and consumer reports. It has been a terrible experience since the moment the warranty expired. First, about 1 month after warranty expired, I had to replace the main electrical board. Then about 3 weeks ago, the drain pump failed. I purchased the $110 pump and installed it myself. Now this week, the spin cycle sounded like a jet engine. I took it apart to find that the bearings were shot on the drive shaft. I figured, well it is just a wear item, understandable right? So I went to order parts and got told that I have to order the whole outer tub for $250 with shipping! For some bearings! I called Whirlpool directly and was given no explanation other than Call some parts distributors. They may be able to help you get the bearing separate, but we dont do that and there is nothing that we can do. Amazing. I equate that to having a faulty brake on my car and being told that I have to replace the whole axle!Fortunately, the washer never really did a great job. It was loud and tore clothes up, so the decision to part ways was not too difficult. I have the list of brands they make and will be sure to never buy another. Im selling this one for parts. Im sure there are others out there that will need a pump and control board soon!

Purchased a larger hot water heater after reviewing the offerings from the big box stores. Obtained a 40 gallon Lo-Nox type. No problem. Found that I did not have time to install and 3 months later had a company install for almost $300. Within the first month the pilot went out at least 5 times. Had the install company come out and take care of the problem. Worked OK for 2 months and now the pilot light goes out again. Watched the flames myself and find them to be yellow. OK, so try to see what the situation is, call the installer, then call technical support. I am in a basement, on a cell phone and the representative basically has zero patience, zero tolerance for questions, treats me like an idiot and probably has never looked at any of the guides but keeps harping on me.I asked 5 times for patience and guidance not to be treated like an idiot. As time went on it was clear that the representative has zero experience in front of the product or the information in the install guides. She kept calling it a manual and I tried at least 3 times to ensure that her manual is the install guide. She never did affirm. I stated I wanted my money back and she stated no. Whirlpool has a very skillful representative to keep consumers away.However this consumer is a small apt owner that purchases appliances, as well as hot water tanks microwaves etc. No longer will I purchase anything Whirlpool. Oh I will send a complaint about this rep, and she said thats fine send it to the PO box Total lack of product knowledge and not even skillful in a conversation asking for assistance. The installer also stated that this product has horrible reviews. I wish I had seen them before all of this. Total frustration and something unwarranted. I am out $900 and am replacing the tank with a Bradford white from the plumber. Lesson learned. Good bye Whirlpool, hope others stay away from Whirlpool everything. Choosing another brand is the only thing that makes businesses wake up and smell the money.

We purchased the Cabrio washer and dryer set 2 years ago (7/22/15) from Lowes and have HATED them since day one. The first wash in the washing machine left clothes dirtier than when they went in. Our clothes have never gotten truly clean. The washer has a HUGE tub which is what I liked about it so I can wash my King sized comforters. What a joke that turned out to be. The comforters only get half wet even on the deep water setting. The machine even left dark stains on my light colored comforter and ruined it. Fast forward to 2 years later and the washing machine stops spinning and fills with water clear up to the top of the tub and wont drain. I had to put the machine on the rinse and spin option to get it to drain. Tried a different setting and it worked for a few months but started doing the same thing. The washer seems to be unbalanced no matter what size load I do. I am thoroughly disgusted with this machine and wish I would have never purchased from Whirlpool. The dryer has always worked fine until recently (2 years after purchase). It quit drying the clothes and leaves everything twisted up and wrinkled, even if I take them out of the washer and shake them out before I put them in the dryer. Doesnt matter what setting I put it on, the result is the same. So now it seems as though BOTH of my machines only lasted 2 years. Im not going to bother fixing them, these will be used as target practice. I will never buy another Whirlpool product again.

I purchased a new water heater in August 2013. The pilot light started going out in October/November of 2013. After calling the Tech Support phone number, (877) 817-6750, I was advised to clean the burner screen. First this is very difficult to do because the burner screen is underneath the water heater and almost impossible to access. Second the closet the water heater is in did not show any signs of debris that could clog the burner screen. I did as they recommended. Several calls, and several weeks later, they finally authorized a technician to come and service water heater. He performed a cleaning even though he couldnt find anything to clean; and he replaced the control module. The new control module worked through the spring and summer seasons and then I started having issues again in the fall, late October. Started calling the same phone number and was told again to clean the burner screen. I convinced them to send out the technician again. The A and E Factory technician came out and only cleaned the burner screen and left before I had a chance to get home. This happened several times and I called Whirlpool every time. The next A and E technician told me to try changing out the draft vent chimney to a different size, which I did. Problem happened Again! I finally asked for another plumber and they sent me 3 names of their authorized plumbers. I called Phil, Philco Plumbing. He told me that I needed to have more ventilation, so I added more ventilation, even though I later found documentation stating I already had more than what was required by the manufacturer. Again, a week later, started having problems. Call back and asked to have my personal plumber come out. This time the rep told me that I have always been free to choose any plumber I wish (why wasnt I given that option the first 10 times I called?). My plumber came out and replaced the control module and the thermocouple, but wasnt convinced that these were faulty parts, he honestly couldnt figure out why I am having this problem, but it was worth a try. That lasted about 1 week and now I am having the problem again!!Whirlpool will FINALLY authorize a new water heater, but they will not authorize installation for the new water heater. I have already spent money on recommended repairs that have not worked. I have taken 15+ hours off of work to watch plumbers do nothing that has rectified my problems. And now Whirlpool wants me to deal with installing the unit myself, OR pay to have it installed! They say they wont cover installation because I purchased it more than 1 year ago. They seem to be missing the fact that I have had trouble with it the ENTIRE time I have owned it!This Flame lock system is garbage. I found on Consumer Affairs that a few years ago a class-action lawsuit settled, dealing with the same issues. I think it is time for another round! I KNOW that I am not the only one dealing with this problem because the plumbers I had out all had similar complaints from many of their clients. Whirlpool wont fess up to the problem, but the problem is real.

We bought a Whirlpool with convection oven, it is beautiful and very well designed and fully electronic. You can only control it via touchscreen Which, when the software runs into blocks, it is impossible to troubleshoot efficiently, you just have to wait until it completes its rebooting. It is very frustrating to spend hundreds of euros in a device you just cant control when it crashes. Horrible programming made for a horrible user experience. You have the feeling of not being able to use it or fix, it is like having a mobile phone or computer Which only works on what appears to be a random logic. The errors displayed on the screen are often vague and the user troubleshooting manual is just plain short. We will return it without doubt and dont recommended ever buying this device.

I ordered this Whirlpool 29 cu.ft. white french door refrigerator online from Goedeckers on April 26, 2013. Delivered May 15, 2013. Ever since we got it, there was a frost buildup in left back of ref. Also ice would fall out of dispenser all by itself. Also a buildup of ice under ice bin. Water would also drip from dispenser. We thought maybe since it was new these problems would go away. But they just got worse. I called Whirlpool & they sent out tech on 8/12/13. He told me Whirlpool has a problem with these refrigerators & would order parts. Well after 3 times of cancelling repairman due to parts on backorder, I told repair I would call when parts come in. I keep calling Whirlpool & keep hearing parts are on backorder, saying parts will be in in 7 days. I call back in 7 days and hear the same lies. Its a shame that they cant get parts in knowing that there is a major problem. It sounds like a real quality control problem. I really pride myself on buying American made but Whirlpool is not helping my case for buying American made. It would be nice if they offered to replace it being they cant seem to find parts.

I have owned a Whirlpool Gold Series Refrigerator for one year and 9 months. During that time I have had 7 repair issues. Each of the past ones took at least two weeks to repair. This past repair has to be redone because the new parts are also bad. The part is now on factory backorder. It will be at least two months for this to be repaired. Whirlpool says its too bad, we just have to deal with being without a working refrigerator for months. Do not buy this product!!! The warranty only means that you are forced to wait months for repairs. They will not replace, refund, or even extend the warranty for all this downtime. You have no recourse with the company.

We purchased a Whirlpool unit Mod#WRF535SMBM from Home Depot in Bluffton, SC. Frost and ice build up in bottom freezer of our Whirlpool unit. We have had 4 service calls since our purchase of the unit in Dec 2014 (April, May, June and Sept) with one freezer door replacement due to a faulty door liner and soon to be a second freezer door replacement due to lack of insulation in the door, along with the door slides. Each service call visit is by a different service company. The other issue is the unit is advertised as S/S. This is the first time I have had a magnet stick to S/S so I figure that the outer shell is a mere coating of some sort and not a quality S/S product.

I have the Whirlpool washing machine for last 15 years and there has not been any complaint since its acquisition. I do a lot of laundry because I have a big family, but not major issue so far. I will recommend this brand to anyone willing to buy a washing machine.

It is a very reliable and efficient washing machine. I enjoy the energy saving features as well as how clean my laundry is, no matter how soiled they may be. I would definitely recommend a Whirlpool washing machine to a friend.

I purchased the Whirlpool washer with the expectation of having at least clean clothes. In fairness, I do wash some pet items but they are done separately. My clothes at time come out dry in spots because theyve not been touched with water. Forget the balancing issue. What I will have to do is wash, rinse, and repeat. This will be my life until I can get a new washer. Never again Whirlpool.

I bought a Whirlpool CABRIO washing machine. I was assured it would do large & bulky. I didnt realize that being so called energy efficient meant that it didnt put enough water in to get my clothes saturated! On large loads or bulky items when I put in my laundry detergent only to find out I had to try to wash them again. Parts of the clothes would still be unwashed & dry after going through a whole cycle! After washing the clothes that did get clean comes out looking like I took them to a stream and washed them on rocks. After taking care of my clothes so they didnt look as old as they were, they are now faded & old looking. I hate this washing machine!

I purchased this dishwasher (whirlpool WDF330PAHW2) in February 2019. Really worked great until May 2020. Now doesnt drain on the last cycle, smells bad (even though cleaned) and door leaks under handle on front. Really too bad. I have been a Whirlpool champion for 25 years. Now not so much.

We bought a Whirlpool washer (Model # WTW4900BWO) and dryer (#WED4850BW) and within 2 months I was having problems with the washer AND dryer. Every time I washed a load of clothes, the clothes would have some yucky stuff hanging all over it. I called Whirlpool and was told to try setting the washer on 1 Rinse with Softener even though I never use a liquid softener. Their suggestion did solve the problem, but why doesnt a brand-new washer work the way its supposed to? A short time later, my dryer buzzer stopped working and the knob would not advance when set on the Energy Preferred setting. I called Whirlpool again and was told they did not have a service technician in the area where I lived and that it was not likely that one technician would come on the same day to service both machines. I asked why they would sell their products in an area where they were not willing to service them and they said that is the choice of the store that sold it to me. Then they told me there was a service technician available about 40 miles away and they would fax the order to them so they could contact me. The technician who came did look at both machines and was able to determine that the control panel needed replacing on the dryer, but was not able to do anything about the Rinse Option problem on the washer. He suggested that I continue to follow the recommendation of Whirlpool as long as it works. I can do that, but Im not happy that a new machine does not work the way its supposed to. He also recommended NOT using liquid laundry detergent or fabric softener in my washer because it contains animal fat and can build up and cause problems. Nowhere in the manual did it say that. He took the washer apart and showed me how it was already building up under the washer basket. I told the technician that my laundry has had an unpleasant odor to it when it comes out of the washer and even after it is dry. He said that might be because of the small amount of water that is used in the energy saving washer. If these problems cannot be resolved, I consider this washer to be a lemon and hope it will be replaced with a new one. If I had to do it all over again, I would buy a traditional washer. I liked the idea of conserving water, but not if my familys clothes stinks.

We got our Whirlpool french door refrigerator with freezer on the bottom (Model: GX5FHDXVY04) in June 2010. In the past six months, the refrigerator portion loses cooling and temperatures go to the 60s or 70s. We found out that by turning the unit off until it defrosts, it will work again for awhile. Weve had water overflow on our wood floor. When this happened the third time, I called Whirlpool to send a repair person.The person I talked to said it could be over $400 to repair and that it would be more economical to get an extended warranty for about $314, which I did. I did not receive the contract via email (it may have gotten lost in spam). The repair man came and said yes, this was a common problem due to a design flaw and that it needed a $6 part to make the water drain smaller - so that too much air didnt get in.It was May 1st before the repair could return to install it. This was done and we thought - expensive but its taken care of. Today, May 5th, the same problem happened and I have to throw away food again. Its the weekend and there is not a repair person available for two weeks - I got an order number and may request that the repair come sooner. To add insult to injury, I found out that the extended warranty is good only up to $450 and not good for any repair that might be needed in a year. Most of the repair goes to travel to get to Fairfield and labor and we have used most of the warranty already.

Takes 2 or 3 full cycles to dry small load. Big disappointment, drying is such a horrible experience since the clothes never dry when I expect them to. Not satisfied at all.

After reading endless stories regarding Whirlpool water heaters, I ended up here and read numerous complaints and every company response had the same message from Chris-- Go to whirlpoolwaterheaters.com/help. I went to the website and called the number (877) 251-1679. I spoke with the most helpful gentleman (Lenny) who helped me troubleshoot some things and even called me back to inquire regarding success and gave me other tips to check if the problem occurs again.

Last July 2010, I bought a Whirlpool Washer with model # WFW975OWW01. It broke down Sept 2011. Fourteen months so its out of warranty. I paid a serviceman $136 to tell me it needs $1,350.00 worth of parts and service. I sent an email to Whirlpool for help but no response.

Bought a Whirlpool Freezer on bottom in Feb 2012. Its December 2015. Only had gotten a 2-yr warranty. Wished I would have gotten a longer one. About a yr ago the freezer started leaking water all over the bottom of the freezer which turned into a sheet of ice... then leaking water all over the floor. Now there is a knocking/clicking noise coming from the back of it. This product is only 4 yrs old and Im praying it doesnt give out on us. That was an almost $2,000 purchase. I was hoping to at least get 10 yrs out of it. Never buying a Whirlpool Fridge again.

Do not purchase (Whirlpool products). Discuss guarantees with salespeople when purchasing! They are total sham and in fact borderline fraud! Purchased $5,000 dollar KitchenAid fridge only to have it breakdown after only 8 months. What they dont tell you is instead of recalling a product they give their repair personnel whats called a notice which means they know there are issues with their products!After much discussion and trying to return the product to no avail, I was told very adamantly my fridge would need to break down another additional 2 times before my fridge would be replaced with a new fridge. Forget about the cost of your food inside the fridge, they dont care! Just beware that their warranties and parts and labour are a complete and utter joke! My advice after much research if you can afford it buy Miele or Subzero product. Its more expensive but a lot less headaches in the long run! Ive eaten the cost of my KitchenAid appliance and went with a Subzero fridge. Dont believe the higher pressure sales pitch from salesman. Youre best to call a repairman and ask what hes fixing more often than not and 9/10 times he will tell you Whirlpool product! Customer service is a complete circus and gong show. Youll get further ahead talking to a donkey!!! Buyer beware! Whirlpool Canada/USA is a joke!!! Dont say I didnt warn ya!!!

Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.

I could echo all of these complaints and more. I just gave up on the heater, junked it, and went to Home Depot and bought a Rheem. Recommendation: NEVER BUY A WHIRLPOOL!

This is not a new washer (Whirlpool Cabrio INTW6200VWO) and it works well BUT since we have owned it we have had rust at the bleach dispenser. I am seeing on the internet there are many complaints about this and there was a recall? But they have run out of replacement parts??? Never received any recall notice. We have online instructions on how to repair and have done this many times and the rust comes back. About a week ago we sanded, primed and enamel painted the area plus I have put NO BLEACH in the dispenser and the rust is coming back. I hate to replace a working machine but this rust can and will get on my clothing. Whirlpool was the absolutely best in the past but this one is a lemon.

I recently purchased a Whirlpool over the range microwave. I especially appreciate the unit's strong exhaust fan. My previous microwave's exhaust fan was much less powerful. The unit's black glass and chrome trim look great! I am extremely pleased with the new microwave.

I purchased a 50 Gal. Whirlpool gas water heater on Saturday, 12/31 to replace a 20-yr old unit that had failed. The unit was installed that day and it started right up but I noticed the burner had gone out about an hour later and the status light indicated FV Sensor Lockout. I tried calling Whirlpool but their customer service was closed. I tried troubleshooting myself using manuals and Internet forums without success. Everything I could find indicated that an FV Sensor failure could not be repaired and would require replacement parts. I called Lowes and was told they could not help me and I would need to talk to Whirlpool.I called Whirlpool again Sunday, 1/1, but they were closed again for the Holiday. I called two plumbers and both told me that the Whirlpool units were problematic and that if they did come out, there would be little they could do except charge me a lot of money and recommend parts to order as Whirlpool does not let them stock parts. Both plumbers also suggested that I consider buying another brand.So I went to Home Depot and purchased another brand with similar specs. I installed it that day and it fired up right away and has been running fine ever since.I talked to Whirlpool on Monday, 1/2, and they told me they would not issue an RMA for a unit that they considered usable. They also told me there was an FV Sensor reset procedure that they would have walked me through had I been able to talk to them that would have bypassed the sensor until a replacement could be installed. I told them that if they would publish this procedure in their manuals or on the Internet, I would have certainly done that. Im now fighting with both Whirlpool and Lowes to get a resolution to this problem. Im not sure about other Whirlpool products but their Water heaters seem to be very problematic.

I purchased a Whirlpool Cabrio and a one year extended warranty two years ago. As soon as my warranty ended, my washer started to malfunction. I recently started to receive the F-51 code and the washer shuts down at the spin cycle. I am angry because I spent just under 1200 dollars on a washer a little bit over two years ago and now, it is sitting in my laundry room taking up space. When I called Whirlpool, they told me I could purchase another repair warranty for $316.94, which would take the cost over 1500 dollars for this washer and there was no empathy nor compassion for what I was feeling as a consumer from the customer service rep. I spent my hard-earned money on major appliance purchase and I think that it is only fair that I get more than a two year usage out of machine that was designed to last at least six years according to their website. There is no way that this should just be my lost and cost me additional funds.

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

I purchased a new Whirlpool Cabrio washer 3 years ago. It is the worst washer I have ever owned. During the first year it had to be repaired. It continuously flashes F51 when I try to wash a load of towels or bedding. I am beyond fed up with this machine and will NEVER purchase another Whirlpool product. If you are considering purchasing one of these I would tell you not to waste your money.

My old dishwasher washed much better than this one. For one thing, I do not think having the silverware basket in the door is a hindrance more than anything. For one thing, the silverware does not always get clean. Even some of the dishes do not get clean. I think the engineering of the dishwasher is poor. When you pull the bottom rack out to put more dirty dishes in, it gets caught on the silverware that are in the silverware basket in the door. Makes it very difficult to get the bottom rack out or in. I have no gripe on the size of the dishwasher. I would just like it to wash the dishes and silverware clean. The appearance of the dishwasher is good but that doesnt clean the dishes. I am more than satisfied with the appearance of it. I do like the buttons being at the top of the dishwasher so that a person cannot bump them when it is running. I just think the design of it could have been much better. My other dishwasher had the silverware basket inside on the bottom rack and I really liked that and if I ever buy another dishwasher, I would make sure that it is inside the dishwasher. I dont believe that Whirlpool is the company it used to be. I have an oven that has been nothing but a problem for me and it is a self-cleaning oven but I cant even use the self-cleaning feature because it blows something in it and it doesnt get hot and clean it. Have had it fixed twice and the company that sold it to us will not even talk to us about it. Im not sure that I would buy another Whirlpool appliance of any kind again.

My refrigerator is about 7 years old. Has performed great. Good use of room inside. Easy to clean. Bought only Whirlpool products for years however since the last purchase of a range a couple years ago the quality was greatly diminished. May be changing brands now.

This machine, like all other water sensor machines, will not let you wash a few items that are lightweight without filling the whole machine up almost all the way. The reason being is that if the items are light, they will float in the water above the water level and the sensor thinks it needs to put more water in and even with putting something in to weigh it down like a wet towel doesnt always work, nor should you have to do this. You will waste more water in the long run if you only have a few items to wash, ie baby clothes, underwear, rags, etc. I am so disappointed that I had no other choice but to get this machine.

I am excited that I found this site, putting it in Favorites! Using the advice from ConsumerReports, we purchased a Whirlpool Gold French door refrigerator model GI 6SDRXXY02. We were looking forward to the energy efficiency reported. I blamed the kids and my husband when the water started appearing on the floor by the refrigerator. After a while, I started investigating and I saw the sheets of ice that had formed in the bottom of the freezer. Several times, I removed the ice, only for it to form and start leaking on the floor weeks later. We discovered the drain was frozen and that during the defrost mode, water would freeze in the bottom, and once the ice was too high, the water would flow over the ice onto the floor. My husband has unloaded the freezer and defrosted the drain with a hair dryer several times. So sick of this!! We never received a recall notice and of course, the warranty is out. I wish we hadnt paid so much for this refrigerator. It would have been out by the curb months ago. We are in the middle of a kitchen remodel and getting new cabinets. I will have to dispose of this expensive refrigerator. UGH, money down the drain!! We wont buy a Whirlpool!!!

Mold in my dishwasher right after having washed the dishes!! This is the first time I have seen the mold on the racks (lots of it!). However, my neighbor also has a Whirlpool and complains of the mold all the time. Also, my dishes often do not come clean. I would not have purchased a Whirlpool, but it came with the house, three years ago. Therefore, I do not have a receipt for it.

Purchased Whirlpool washing machine two years ago but transformed into junk within two years. Fraud company only searching ways to loot the money of the innocent customers and manufacturing such appliances which greasing mentally.

Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty. Spoke with manager, Tracy **. She said they would not help - out of warranty. Called local parts/service center - ea. hinge is $42 plus shipping and labor to install. Obviously this is a defective design. The lid is too heavy. I was having a difficult time deciding to spend 150-200 dollars every 2-3 years for hinges on a $700 washer and then I read all the other complaints about Whirlpool washers. I will sell it for scrap and buy a better brand.

Well, this saga continues. Whirlpool dishwasher was purchased at the HH Gregg on Rockville Road on March 17, 2012. Whirlpool dishwasher broke down on May 17, 2012. I bought the extended warranty but who cares? HH Gregg doesnt because it does not go into effect until a year after purchase. So since its less than year, I called Whirlpool, who sent someone out a week later, who, of course, cannot fix the brand new dishwasher because 2 parts had to be ordered. This was almost 2 weeks ago! I still have not heard from the company, A & E, who works for Whirlpool here in Indy. Whirlpool called me on Monday to tell me theyre sorry and blah, blah, and will try to find part in five more days. Then ship it to me, and, of course, it will probably take another week for the maintenance man to fix it. I mean, I grew up having to wash dishes by hand, so no big problem. But when you spend $600 to $800 for a supposedly nice product to enjoy the leisure time of your life and get extended warranties, you expect it to work for at least 6 months before breaking down. So be warned. Do not buy Whirlpool, and furthermore, beware of buying extended warranties and appliances at HH Gregg.

I purchased the hot water tank from Lowes 3 years for over $500.00 within the first year, I experienced issues. I have the same pilot light problems as everybody else. I have hired a plumber four or 5 times to clean and blow everything out as instructed by Whirlpool. The hot water heater will not stay lit. The plumber has replaced every part possible two times. Customer service continues to inform me to do this and that and everything has already been done. I am without hot water again with children in the house. Once again, we are boiling hot water so that we can bathe--total inconvenience. This product is defective, and has cost me money to hire a plumber each time. I would never recommend this product to anyone!

Sturdy, durable, and flawless operation, from the 5 multi style smooth top elements to the self cleaning convection oven with the secluded bottom element. It is a sleek clean looking appliance, and its the best weve ever owned. To one that says they dont make them like they used to, I say thank God!

We had to buy a new fridge in 2000 because ours broke. Following consumer reports, we went with a side-by-side Whirlpool gold and was it pricey! Within the first five years of its life, we had to replace the fan twice...the bar that separates the fridge and freezer could have fried an egg--it was so hot! When I had to replace it the second time, I pitched a fit to Whirlpool and they could care less! Now I see that the inside wall of the fridge section has cracks forming! I know the average lifespan is 10-15 years but I still will say that I will not buy from Whirlpool anymore! Their stuff is very expensive and it just seems it has too many small things that do not hold up!

Do not purchase Whirlpool smart freestanding gas range model number WFG975HOHV. I purchased the range and the refrigerator around Christmas of 2018. The first time I turned the oven on to make Christmas dinner the carbon monoxide detector alarm went off. I have tried to use the oven twice after that and the same thing happened. The oven also never gets to 350. I spoke to Whirlpool who said to unplug the oven. They stated a technician would be sent with a carbon monoxide detector and to conduct repairs. The technician came and could not get the oven to 350 and the carbon monoxide detector alarmed. He stated he has to order parts and return to complete repairs.This is a brand new oven that I could not use because the carbon monoxide alarmed and the oven was not heating to 350 because it keeps restarting every few minutes. So here I am not able to use the oven for over a month and waiting for parts for a brand new range. Do not waste your money on Whirlpool products. Also the customer service has no empathy knowing their products are defective.

July 2017 I purchased a Whirlpool refrigerator Model # WRF757SDEM00 S/NK51709722. The refrigerator portion went out, the repairman said it was the fan therefore I spent 351.00 dollars for house call and fan. When that did not work the repairman spoke to whirlpool and they said the panel of small computer may go out with it 212.00 plus tax. Did not allow that and tried another repairman who said the value that switches from freezer to refrigerator was out and if I could find someone to fix it would cost between 600 and 800. I went out and bought a Samsung because on the front said 10 year warranty. At least anything is better than 1 year whirlpool offers. There is NOTHING in the name.

Our side by side refrigerator is 2 1/2 years old. The LED lights are not working. Had to call repair service because one cant get into the housing without a service tech No9 normal screw in light bulb to replace 2 burned out light bulbs AND pay for the service call is $475.00. THIS IS HIGHWAY ROBBERY. I would expect to pay for a major repair BUT A LIGHT BULB. DO NOT BUY A WHIRLPOOL REFRIGERATOR WITH LED lights. This is a major flaw in their manufacturing and If they go out again the fridge will go to the landfill.

My model # is WTW4800BQO. Purchased 05/20/14 and, under warranty, had repair come several times and they finally supposedly replaced the brain of machine and said nothing further could be done. So all this time I operate the machine manually - timing everything from wash to spin. On all cycles I have to manually - actually turn off machine when first wash is completed and reset to rinse and spin otherwise it only partially fills and drops the water right away on the 1st rinse (besides also dropping water on 2nd rinse). Also I came home one day, after completing a wash load earlier, and found the machine filling up with water automatically so now I always have to be sure the machine is unplugged when washing is completed.

Have had this refrigerator for about four years and its broken down twice. It has rust and stains on the outside which are hard to remove. I have had other refrigerators that have lasted longer and were in better shape.

Whirlpool wsv07 psl satina - I bought my whirlpool, two-door whirlpool ref last Jan 2013. Just few days before the warranty expires, I had prob with gasket on lower door. And now six months after the warranty expires, the freezer is not working and wont make ice anymore... and I will be charge 400php for check up. Reading on other reviews, I bet I am buying a disposable appliance from whirlpool. The national ref of my sis been a service to her for more than 10 years and its still going good. Our GE ref prior to whirlpool serve as for 19 years.... but this brand sucks.

I bought a Whirlpool refrigerator in April. The motor ran constantly. The company replaced it for me but it was back ordered until July. The one delivered in July kept freezing the items in my refrigerator. I had two service people come out to replace parts in the next couple of months. The entire time having to throw out frozen food. Finally, they had another one delivered in November. This one continues to freeze food in the refrigerator. Mind you, I just got it and they want to start again with service. Seems others are having the same issues. My 4 month old gas oven is also not broiling. Customer service is awful. Every time I call the wait time is over an hour and then they don’t really help. I would not recommended Whirlpool to anyone.

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!

I have had my Whirlpool stove for over 30 years and use it daily. Still a great stove. I would not trade this stove or any of the new types. I just need to get the self cleaner repaired. The only problem I have is finding parts to fit this older stove.

This is the second time since I have bought my Whirlpool top loading washing machine, which was January 1, 2011. During a power outage, I was washing clothes and my machine lid would not unlock after our power came back on. I called the warranty service and they made arrangement for a repair man to come out to repair it, but the appointment was in two days. Meanwhile, I had clothes in the machine I needed and was afraid they would become molded and no good. So my husband opened the lid and I removed the clothes. When the repair man came, he was not going to repair the machine because we opened the lid. He was very rude, but after doing some talking he repaired the lid. Now, once again we had a power outage while I was washing clothes and the lid is locked on the washing machine and will not open. This happened Friday, March 16, 2012; my appointment for the repairman to come is Tuesday, March 20, 2012. Meanwhile, my clothes are sitting in the machine wet because we were told not to try to open the lid and wait for the repair service to come. I am very concerned my clothes will be molded and I will be unable to use them. I would never buy another washing machine like this one. Model number is WTW4800X, Standard/Ordinaire VOXr8ENA(3B). Date of purchase: January1, 2011.

New whirlpool washing machine 2016 - This washer is supposed to be smart, but it NEVER fills up with water! I always have to fill a bucket with water and throw it in the washing machine. My clothes do not come out smelling fresh and its not the detergent to blame, its the washer! Im so disappointed with this product. Whirlpool should stop making products.

We purchased both the Cabrio Whirlpool washer and dryer approx. 3 years ago, while still under the manufacturers warranty the lid cracked upper right corner. It was replaced and we were told by the repairman at that time this is becoming a common problem that he himself has seen this exact failure to several of these washers. Whirlpool needs to fix the problem. Shortly after this happened we receive in the mail the information for the extended warranty. Due to having this already happen, I phoned the extended warranty department for Whirlpool and specifically asked if this same thing happens again will it be covered under the extended warranty. My answer Yes.Well it happened again, called extended warranty provided them with a detailed description of what happened, they would send someone to replace, the service gentleman arrived today, called Whirlpool and they denied the claim. So they LIED. I instill honesty in my children and am proud to say I hold honesty as a high value. We were told it was cosmetic, the glass is buckled and the lid has to be held down to engage the lock mechanism of the lid. COSMETIC, this is a SAFETY concern. Where have our American values gone... Whirlpool used to have them back in the day... Shame on you Whirlpool.

I love my Whirlpool refrigerator, its great. I have not had any major issues with this brand. I only wish that the freezer was made a little different. Im not a big fan of the side-by-side doors. I would much rather have the one with the freezer at the bottom and the fridge at the top...

Our newly renovated condo came with a Whirlpool washer/dryer, and its been a nightmare. Not only has the unit destroyed 5-6 items of clothing, but weve had to have two repairmen out to remove socks that were sucked into the drainage pipe. On top of all of that, the customer service has been terrible - their hours are very limited, and theres nothing the call center employees can do beyond sending a tech out to look at your appliance for a cool $175. All this for a machine that was purchase new in June 2014! We will never buy a Whirlpool product again. Sad example of why American manufacturing has so thoroughly declined.

Whirlpool Cabrio Washer WTW5000DW - I have owned at least two other washers in my life, and I just recently bought a new washer/dryer set at HHgregg. Was told they are doing away with agitator washing machines in the very near future so this is my first experience with a top load agitator-less washer. This thing is AWFUL!! First of all it took a minute to get used to the weird popping, grinding noises it makes while going through the cycle (which I might add seems to take FOREVER). The other thing I hate about it is there is no way to add the fabric softener at the start of the wash in this model unless you have a downy ball of which I have yet to find at my local dollar store or even the KROGER??? So I run back and forth trying to catch the rinse cycle to STOP the machine (wait I might add) and then add the FS manually.BUT THE ABSOLUTE WORSE THING is - my clothes come out with SPOTS that look like lint all over them, and they wont wipe off unless you have a wet rag to do it with!! AND YES - I have cleaned this washer TWICE already since January with the very expensive AFFRESH. I wear scrubs and they are solid colors, so it really shows up and I have to wipe off every pair EVERY day before I put them on then roll a lint brush down them. WHO HAS TIME FOR THIS??? This is on my SOLID colors which is easy to see, I can only imagine the GUNK that is on the rest of my laundry!!! I dont feel like my laundry is getting clean at all!! I am divorced and money is tight - I paid around $500 buck for this piece of crap. I am already seriously thinking of getting me another one - the OLD tried and true kind with an AGITATOR! And yes I am ANGRY. Can you tell??

We our adding our name to a list that is remarkably long. We purchased a top loading Cabrio washing machine just over a year ago and the problems with the balancing of the unit are the same as everyone else who has written in. The service company A&E has promised a lot but has done little to resolve the issues we have had with the machine. One representative told us that she would order the part and have it sent to our home. When the part did not arrive, we called A&E back only to find out it was never ordered because the service technician would not return their phone calls. I find this excuse ridiculous and similar to other false statements they have given us on the other four phone calls made to address the problem. After reading these reviews, we realize that this is only the beginning of what will be a frustrating and costly experience. Never again will we buy a Whirlpool!

We bought Whirlpool Frontloader Washing Machine not over 1 month ago and it started to malfunction showing Ed1 error on its display. We contacted the service center and it was taking too long to have a visit from a technician. Then the technician, who also installed the unit came and checked the unit. He called someone from corporate office or from support team to ask what is error code Ed1 and overheard over the phone that this is a known issue on the brand. The technician said it is possible that unit will be replaced or only the motor. I contacted the brand support thru Messenger and requested to have the unit replaced, because again, the unit is not over 1mo old.I was advised it is not possible as replacement of unit is only applicable when the issue happened within seven days of delivery. STUPID ISNT? Policy is something unworthy for a product that is over 30k. And again, unit started to malfunction not over a month after it was first used. I would say we pretty much took care of the unit, we only use it twice a week. Placed it where it was perfect to put. Followed every advice given to us by the technician who installed it but still, it malfunctioned a few weeks after we started to use it. I am ashamed of the brand itself, we should have chosen Panasonic or Samsung instead not a dumb brand like Whirlpool. I certainly do not recommend the brand for a washing machine unit. Frontloader is a crap.

My Whirlpool Microwave models WMH32519FS was installed in my new home by the KB Home builder Nov 2017 and went bad on Nov 23, 2018. As write this, my microwave is 1 year & 15 days old. Just out of warranty. The micro Keep show the same issue, open the door & closed the door. Still is not working, the microwave died On Black Friday 2018. RIP Whirlpool, I will never buy you.

This is my third Whirlpool refrigerator. The first two lasted about 20 years each, and although not fancy, they were always serviceable. This one is different.Because of my kitchen cabinets, the only refrigerator with as much storage capacity (cu ft) as my old one was what seemed to be an almost identical Whirlpool, with the only exception being a slight difference in the ice maker. But this one is a disaster. The water/ice dispenser has been changed to one with one space only for your container. The water that comes out is warm, because the routing of the tube has been changed and it no longer goes through the chilled refrigerator space; the ice pours out so hard that usually half of it lands on the floor. In order to operate the dispenser using anything with less than a 4 diameter, you need two hands: One to depress the lever behind your glass and one to hold the glass farther away from the refrigerator. Failure to do that results in a wet mess. After dispensing crushed ice, it continues to send small pieces flying long after I change the switch to cubes. But that is the least inconvenience. In an apparent engineering change to meet energy efficiency, the new refrigerator recycles air from the freezer to the refrigerator compartment. That and other changes in the frost-free engineering have resulted in:Uneven cooling in the refrigerator. In fact, it froze $1800 worth of insulin pens. I was advised by the Whirlpool representative that I shouldnt have put them on the shelf where the vent from the freezer spews out freezing air. Spoiled food in the freezer. Everything in the freezer develops a thick coating of ice crystals within a short time. This dries out the meat, shrinks the popsicles, and destroys the quality of fish and fowl. At this moment, I have two pork chops that defrosted in a plastic container on my kitchen counter. I bought them fresh, and now the 10-12 oz. of pork is swimming in over 1/2 c. of water.Interior fittings are poorly made and shelves and drawers do not work easily. The allegedly stainless exterior is difficult to clean, and many reviewers have remarked that they find rust within a few months. I could go on. There is more poor engineering, and an array of noises filling the kitchen, but you get the picture. I wish I could trash this refrigerator and buy a good one, but that isnt feasible both because of budgetary and space constraints. The last service person who came out sighed and told me that the refrigerator was cold, and that meant that the unit was operating okay! I HATE this refrigerator and struggling with it from day to day. My hope is that no one will buy a Whirlpool ever again. I certainly wont.Updated on 12/05/2017: Whirlpool, faced with my wrath over a refrigerator set on LOW that froze $1800 worth of insulin, provided a replacement (25 Cu Ft side-by-side refrigerator). I have owned two previous Whirlpool refrigerators -- for 20 years each -- as well as other Whirlpool major appliances. I WILL NEVER BUY ANOTHER WHIRLPOOL APPLIANCE. The replacement is deficient in every design and functional aspect I can think of. Temperature is uneven in both freezer and refrigerator. Food in the freezer is coated with snow within a week and dried out and spoiled within a month. Ice comes out with such force that it ricochets out of the glass and around the floor. Water from the dispenser is warm. Leafy vegetables spoil within 2 days. Whirlpool sent technicians who informed me that the unit was working properly because it was cold. PIECE OF JUNK! DONT BUY ANYTHING MADE BY WHIRLPOOL!

I purchased the Whirlpool Cabrio HE top loading washer and front-loading dryer about 7 years ago. It has been okay, but nothing special. Recently it began stopping in the middle of the cycle and showing an F51 error. Then all of a sudden the noise during spin was deafening. Brought out a tech, who came and did some eval. Left with some basic maintenance. Did a load, and happily no more F51 code, but still so very loud during spin cycle.Called again; tech returned and said that drum and shaft would likely need to be replaced to the tune of some $500. The same story as others have told. We should have bought the extended warranty. Like others, I also felt that washers lasted at least 10 years. And that seemed a short time given expectations in the past of 20 years of service. Im disappointed in Whirlpool. Even though Consumer Reports gives the Whirlpool Duet washer (new 2013) one of its highest reviews, I cant bring myself to buy another Whirlpool product. It appears to me that this warrants recall as well.

I have a home that was new 5 years ago. My microwave/oven Whirlpool Gold was built in March 2005. The light bulb went out in the microwave 3 days ago. The users guide that comes with the unit says for this call assistance. I called the local appliance co. Cost to replace the bulb is $10 parts, $65 service call $25 labor thats $100 plus tax for a $.10 bulb! I called Whirlpool. What a joke, the biggest bunch of puppets paid by a Michigan based company who never heard of what happened in Detroit! They were no help and understood my frustration but flat did not give a **! For a $.10 part Whirlpool is willing to get bad press worth whatever I can amass!

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...

I like the Kenmore dishwasher as it has the cutlery basket in the door. This leaves more room for dishes on the rack instead of taking room up for the cutlery.

My 4-year old water heater has upper/lower sensor issues for the fourth time this year. The rep was supposed to send replacement parts to arrive today (day four with no hot water), but the wrong ones were shipped. A different rep called and offered to exchange the unit for a new one. The expense to me will be $350-$450 for the plumber to uninstall my unit, take it to Lowes and bring the new one back to install. The plumber suggested I take my $450 and just buy a new non-Whirlpool unit. He knew immediately that I had a Whirlpool hot water heater because its the most common repaired vendor. Whirlpool should be covering this expense for re-installation of their inferior product. Poor customer service. Day 4 with no hot water during the holidays with no solution in sight short of me purchasing a new hot water heater. Whirlpool finally got the right parts to me and I paid a plumber $190 to install. One week to the day later, my pilot light will not stay lit. No change in ventilation since it has been installed. I will say I have been dealing with their rep Chris on the phone who is extremely nice and I feel sorry for him. But we all have the exact same issue which is not being resolved.

Whirlpool 27 cu.ft french door bottom mount WrF989SDAH White - We took delivery of this ice making fridge mid-September from Sears Canada. 3 weeks later we have ice at the ceiling/wall seam at the back inside the fridge. Water collects along the rubber seal of the freezer drawer which we have to mop up. We said we were not going to use the water/ice maker and its not even hooked up. Water comes down through the water dispenser onto the panel which we also mop up. Moisture in fridge. Temp settings are as factory specified. Whirlpool authorized tech guy gave us the inside info. Hes seen so many design problems with this model and what Whirlpool do is order the tech guys to say to customers we can order the parts and fix it. Whirlpool keep discovering and modifying the problems but you are not allowed a refund off the bat because the tech guys authorized & sent out by Whirlpool are not allowed to give a report to the retailer or say its design defective. So the customer has shelled out money and has to have band-aids left, right and center. Went to Sears to ask for a refund. They refused because tech guy wont give a report to them (but what do we really know eh? Because the tech guy stood in my kitchen and gave a verbal report to Sears but nothing written). So Im in the hole for a crap product that is only a few weeks old and Whirlpool and Sears have got us over a barrel. The tech guy said he was going to challenge their tech line now because hes upset at how many of these band-aid fridges hes seeing now. I want a different brand and model and cant have it because Sears dont have it. In dire straits now.

This washer is 5 years old and the top is rusting out on the inner rim. I have city water that has been tested and found to be totally safe to use and drink. Neighbors using the same water and owning different brand washers have no rust problems. Does anyone else have the same problem with their Cabrio washer?

I have had my refrigerator for eight years. Only had one prior repair which cost me $85. I have had a wonderful experience with this particular product. I am pleased with the liability and hope to replace with an equal or better appliance.

I am so unhappy with my Whirlpool Cabrio washer and dryer. The clothes get so tangled and twisted that it stretches my sweaters totally out of shape. There is not enough water on any of the cycles that really clean your clothes. I saved my money so I could get something energy efficient and look great in my new laundry room. I would never recommend this product. Your sheets will not come clean because they ball up in the middle of the washer and come out partly dry. I have had this set for 3 years and now the bearing is gone; it leaks from the bottom and throws grease all over my new floor. I have battled the horrible odor since the second month. It smells so bad that I make sure I dont wash the day I have guest over. I am so disappointed and mad at myself for not reading any reviews before I spent my hard earned money. So here I am now 3 years into my ownership and having to spend more money on a defective product. The sad part is that I really thought I was getting something nice that would last me and my husband for years. There are only two of us in our household. This machine does not work properly; now it is broken, but hey it really looks good.

My brand new top-loading, high efficiency washer has squealed like a banshee from day one. Whirlpool replaced the main agitator part, with no success. It still squeals so loud, you cant have a conversation in the same room. Now, Whirlpool says that it is normal. No, it is not normal for a washer to squeal so loud. I am still waiting on Whirlpool to replace the same part they replaced the last time. We are still not abe to hear each other over the squeal of our new Whirlpool washer. This is not normal.

I have clothes that are coming out torn with large holes, especially cotton items. I dont know if it is the washer or dryer.

On 2-26-13 I received my new Whirlpool Refrigerator, Model WRF989SDAE, KSN 4191832, 28.6 cu ft, french door for a price of $2500.00. November 2014, refrigerator stopped working. Though it was not under warranty any longer, the repair company advised me that the problem was a warranty item and repaired it at no charge. This process took several hours of work by the repairman and two visits. He advised that this is an issue with the refrigerator and Whirlpool is aware. Now, May 2015, only 6 months later, ice is building up on the back wall of the freezer and the freezer is running constantly and very loud. Bringing in repair person, hopefully before it stops again. Appears to be related to the initial issue. I cannot trust this refrigerator and would highly advise everyone not to purchase a Whirlpool refrigerator. Refrigerator needs to be replaced, not repaired.

I purchased a Duet Dryer less than a year ago and it stopped working. Got the warranty people to send someone to diagnose it. The repair person ordered two parts to fix it (they took the control panel off the order for some reason). They sent a second inept person to try and install the part they did send and it did not work (He was the most condescending person I have ever met but that is another story.). Of course it did not work and they actually have to replace the control panel AND the electrical panel (which as you know was ordered by the original tech, but taken off the order by who knows?). Now they are telling me that the part that they should have ordered 2 weeks ago is on back order until sometime in May. All I am getting from Whirlpool is lip service and they honestly do not care one tiny little bit that I have a dryer under warranty that will not have been working now for close to six weeks. This is unacceptable business practices.For the record I bought the unit at LOWES and they too refuse to stand behind the product. Basically told me tough they have nothing to do with it. I also purchased an $8000 Kitchenaid (Whirlpool) Refrigerator 5 years ago and the control panel went out about 4 years later. They stopped making the part and I have to THROW away an $8000 refrigerator because they dont make the part for it. As evidenced above, Whirlpool products do not stand the test of time and when they do break (even under warranty), they cannot fix them in a timely manner or at all in the case of the refrig (not under warranty). I caution every reader of this diatribe to choose wisely WHERE you purchase your appliances and carefully select a brand other than Whirlpool (and its brand affiliates of Kitchenaid, Jenn-air, Amana and certain Kenmore products).

I used their website to schedule an appointment for an estimate for a repair on my oven. I was never told they were sending an independent contractor to do the repair nor that there would be a charge for the estimate. I contacted Whirlpool and was told there is nothing on their website and I should have asked the service technician before he was at my door if there would be a charge. Therefore, it was my fault and I indeed had to pay the charge when I declined to have my oven repaired. I paid an independent contractor hired by Whirlpool for $129 to give me an estimate on the repair to my oven despite never being told of such a charge prior to the appointment.

CABRIO GETS A ZERO RATING. We are sorry we ever bought this washer in 08. The unit had a defective main control board and was replaced in 2012. The factory authorized service agent from A&E literally robbed us of jewelry while in our home. Now the main electronic control board needs to be replaced again. Neither Whirlpool or their authorized agents are truly customer service oriented on the defective product. Neither are willing to make an honest attempt at regaining our trust. I have contacted both and neither will acknowledge or offer reconciliation. The problem with the main board and the recurrent F-50 error has been denied by Whirlpool although acknowledged in numerous consumer forums as this. Our family is now without a wash machine. We have not even received a simple apology for the theft from the service agency - even though their employee has been arrested. BEWARE!

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

I love that as soon as Im done cooking. I can lift my grate with oven Mitt, clean the gas cooktop before food becomes caked on. My stove looks as good today as day I bought. The third rack was great for holidays.

It’s just a month old not even - and the dishes are not coming out clean. The cups are stained and I don’t feel it’s clean as it should be given it’s a brand new machine. I would not recommend this particular brand in Dishwashers.

I owned the Whirlpool washer for 13 months until it quit. Menards was no help with anything. I am going tomorrow to get to try my luck with Samsung.

We bought this Cabrio washer WTW6400SW2 several years ago. Immediately after having it delivered and installed, it started displaying an F1 fault code. The main control board was replaced under warranty. It happened again within six months. Another board was replaced. That board lasted another six months. The warranty was up by then, so I used the machine by hovering over it and restarting it every time it failed. After two years of this piece of junk, we put it in storage while we worked on the road. It was brought out on 10/01/11. I called a repairman (who came on 10/04/11) to come replace the board again. He told me that the last two times it had been replaced with the same defective board, that Whirlpool had never fixed the problem. He claimed he had the new improved board, which he replaced for about $350. Two days ago (361 days later), it went bad again. The same repair company came back and said it was the board again. I just tried chatting with a person working on the Whirlpool website. They (of course) said they would do nothing about the washer. They do not stand behind their product, obviously. Does anyone know of a class action lawsuit over these washers? It is a ridiculous amount of money to spend for a product that does not work. This is just wrong!

The washer and dryer are great. They were a reasonable price and they have not failed on me yet. Thank God. I like the little reservoirs where you could put your fabric softener and soap which this one does not have but it was a good price so I ended up purchasing it. The whole family puts all their clothes in it and it runs on a daily basis so I have nothing bad to say about it. Thats for sure.

GS6SHEXNB02 Whirlpool Gold Refrigerator - Bad ice maker module. Ice maker valve is bad. Its gone out 3 times a year since I got it. We order a replacement, it goes bad again. Its not the ice maker itself, its a bad valve. Signs its going out, ice maker stops making ice or the ice cubes are small or the refrigerator water will start pulsing coming out (start and stop). Whirlpool made a bad product and they know about. Several complaints online about the ice maker no longer making ice. Bad product.

Very durable. Not pretty but will last a long time. The dishwasher will run forever. The appearance is bland so the product is nothing fancy. It gets the job done. The machine is very quiet. I think this feature is the best one.

Its just a plain refrigerator. No bells and whistles. It could have more space in the bottom and well as a ice machine or ice maker. Nothing special about it. Just a place to keep food. The light in top could be higher so food does not touch it.

My new fridge is extremely hard to open. The technician that was sent out told me that there is too much suction building up inside the fridge and freezer and that is why it has to be yanked to open. This is not only annoying it means the fridge is constantly being pulled forward out of place. Technicians solution was to deactive the castors under the fridge. At the time he was here I did not realize that I could then no longer move the fridge out of its place to clean. I called Whirlpool and complained and was told that they could do nothing more for me because the fridge is in good working order. I hardly would call this good working order. They also informed me that if I wished to clean under the fridge or the coils at the back it would require a service call to move the fridge and I WOULD BE CHARGED EACH TIME. Needless to say I AM VERY, VERY UNHAPPY WITH THE WHOLE SITUATION.

Purchased washer 01/20/2012 after prior bad experience with washer, purchased from Sears. The washer is two years old and began making an awful noise and quit spinning the clothes dry. I too have had problems with getting service and cant see spending $500.00 for repairs on a washer that cost me $653.81 to purchase. Whirlpool and Sears better take their head out of their bum before the completely decimate their customer base. Why arent these problems being fairly addressed? It says a lot that your original warranty is only a year and any additional warranty is cost prohibiting. Save yourself some money and frustration and buy the old fashioned top loaders with standard agitation. AND WHIRLPOOL CAN AND SHOULD BUY A VOWEL AND REALIZE THAT IF IT DOESNT WORK IT ISNT MORE EFFICIENT!!!

We purchased the Whirlpool Gold Series smooth top stove from Lowes in December of 2013. The stove is not even 2 years old and it doesnt work. Last September, I noticed a few times that while baking food in the oven, it was burnt after only 10 minutes, due to a runaway temperature. After that, the oven wouldnt heat up properly, it would take too long to bake anything because the temperature wouldnt reach the reading on the display. Then it just stopped baking or broiling all together with the error Feature unavailable. Weve had a serviceman out at least 3 times. Of course, the warrantys run out and its cost us close to $500 to keep fixing it, and two motherboards and a bottom element later, its still not fixed. They wanted to order 2 more parts at our expense, but we cant continue trying to fix this lemon. I will be shopping for another oven, and will never recommend Whirlpool to anyone.

I went from an HE front loader to an HE top loader (Whirlpool Cabrio WTW7000DW0) due to the risk of mildew with the front loader. Im not the only one doing laundry and if someone else does it, it always seems that they shut the door when empty, contributing to moisture and mold that needed to be cleaned out of the gaskets. I am so unhappy with my top loader HE washer. When I stop the machine and look, I always see my laundry half covered with dingy water, sometimes part of it still dry at the top and it is disgusting. I frequently have to rewash loads due to detergent getting trapped in folds or pockets created that hold on to dirt and lint, even being careful with the detergent amount. I run the washer now every time with settings of deep water, extra rinse, heavy load and presoak with instructions, with settings taped to the top for others.At almost 1 1/2 hours each load, we just cant keep up. The laundry still forms pockets and sheets form a giant tent over the entire load that has to be unraveled at the end of the cycle and wound so tight it had no chance of rinsing. I had to get a repair person out because it got out of balance and he had a small hand-held computer to enter a code to rebalance it. When we discussed the issues I was having, he was ready for everything I was doing wrong. He told me I can not wash blankets or large items (I thought I was buying large capacity with such an enormous drum). He told me they have caught people adding water with a bucket during cycles and that the washer software can tell them if people are trying to work around the system which voids the warranty.Apparently, this is a common complaint he blames on the government wanting high efficiency so they make the numbers look good, sacrificing the ability of the washer to perform at what a consumer expects. I have never seen the water in my drum higher than a couple inches and the drum is HUGE, but never used to capacity. He told me his wife demanded they get a commercial washer because she was so angry about how poorly it cleaned. I feel so scammed and I wish I could have my old agitator back. $100 for the repair call, $150 for the code to be put in and Im on warning that they will see if I try to add water, run out of balance or dont comply with any reason they can void the warranty by just checking the data the washer is collecting on us.

Late on the evening of Monday, January 27, 2014, after springing a leak in my 8-year-old water heater, I purchased a new Whirlpool model N50T61 replacement from Lowes. Installation went smoothly and the unit lit off fine the first time. It heated the initial tank of water rather quickly, but the next morning, I noticed the status light on the control unit was not blinking, which indicated the pilot light had gone out. I relit the pilot light, the water heater fired off and appeared to be working properly. 12 hours later, the status light was out again. I relit the pilot, but within 20 minutes, it went out again.On Wednesday, the 29th, I called Whirlpool customer service and explained to the representative what had been happening. He stated that since the status light was not blinking a code, the problem was either an air supply or venting problem, and he couldnt help me. I relit the water heater again and performed the match smoke test described in the owners manual on the vent connection. It did exactly what the manual said it should do, so I assumed that was not the problem. However, while performing this test, the water heater went out again. This time, being right there when it shut off, I saw the status light blink twice about 5 or 6 times before it quit blinking all together. The two blink error code indicated low millivolt signal from thermopile.I called customer service again and explained to the representative what the first person had told me and also told him the results of my test and that this time, I had observed the two blink error code. He asked if I had a multimeter (which I do), so he had me disconnect the wires for the thermopile, connect the meter to the wires, light the pilot and read the voltage. My meter is an old analog unit, and not capable of reading millivolts (which is what the thermopile output is), and I informed the rep of this, but he had me do it anyway. As I suspected, I saw absolutely no reading on the meter. The service rep stated that he believed the error code and decided to send me a new thermopile assembly. However, their shipping department was closed for the day and I should not expect to see the new part until Friday. This was unacceptable, but he stated that this was the only option available to me.After thinking about this situation for a while, I again called Whirlpool customer service and told the representative that I was not satisfied with the solution previously presented to me and that I wanted a return authorization to take the water heater back to Lowes for replacement. The rep stated he couldnt do that, but said that there were a couple other things I could try. He attempted to explain these procedures to me, but wasnt able to do so clearly. He stated he would email the instructions to me. As of this writing, I still have not received the instructions.In the meantime, I did some internet research and found that Whirlpool water heaters have numerous chronic problems, including the issues I was experiencing. I decided this was not a product I cared to own. I called the Lowes store where I purchased the water heater and spoke with the manager. I explained the entire sequence of events to him, and he told me to bring the water heater back for a full refund. Since my local Lowes store only sells the Whirlpool brand, I took the money and purchased a different brand of water heater from another home improvement store. Needless to say, it will be a cold day in hell before I ever purchase another Whirlpool product.

I purchased this model 2 years ago. I absolutely hate the fact that there is not enough water dispensed to clean my clothes. Part of my clothes dont even get wet, therefore, I have to press pause and add 2 to 3 gallons of water during the wash and rinse cycles. I do like the spin cycle as long as it does not get unbalanced.Wished I had never purchased it.

I purchased the four-door Whirlpool stainless steel refrigerator. It was installed on the 15th of June. One month later, the ice was not coming through the dispenser and if it did, it was a small amount. During this time, I was receiving notices from them about purchasing an extended warranty. Today, August 23, 2012, the ice maker stopped working completely. I was disgusted. Paying for the top-of-the-line refrigerator that doesnt last for 90 days is ridiculous. Also, the handle on the vegetable keeps coming off. That will be the last Whirlpool appliance I will buy.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

The washer has a convenient water level feature which enables conservation. The dryer also feature multiple heat/timing features, another conservation plus. Both are compact and easily loaded and unloaded. The multiple alerts at the ending of the dryer cycles are a convenience.

Whirlpool Cabrio - This expensive machine should be called the Presidential. First it spins, spins, spins. It sprays tiny amounts of water, so little, that there is 2 inches or less. There isnt enough water to cover the clothes so no agitator to stir and mix them. There are ridges on the bottom of the tub called aggrivators to twist everything into pretzels. This twisting spreads the dirt around, but does NOT remove it, the utter lack of water giving it no where to go. I use a hose to add extra water, and I hand soap dirty spots. I stop the washer frequently to hand rub and slop the clothes around and un-twist them. Explain to me how running this machine 3 times plus adding water saves water and energy. I cant, in good conscience, sell this POS to someone else, and I cant afford something else. I sure miss my simple reliable old Maytag. I could say even more about this atrocity, but not now. I HATE THIS POS!

I purchased new and installed my heater in 2003. SN: 0253109845, MN: EE3J50RD0454. I started removing and replacing or cleaning heating elements in 2011: pretty good service. In 2015 I noticed black and brown water coming from the hot water taps. I opened it again, cleaned it, and realized anode replacement was required. That is when trouble started.I tried everything usual including 4 foot cheater bar, heating the coupling, impact wrench, tapping with a hammer, etc. Finally found a 700 ft-lb. pneumatic impact wrench on sale at Harbor Freight. After serious wear and tear on my air compressor and about 1-1/2 hours of work with the impact wrench, I got it out. The threads were messed up some, but I did not look close. I had to put the 1-1/4 inch head back in to return it to service while I found and ordered an anode. Could not get one from Whirlpool and could not buy one in Lowes where I bought the heater.The surprise was when I cleaned the threads to put the head back in, I had to use almost as much time and torque to get it to stop leaking as I did when I took it out. Then, when I did try to install the new anode, it required to same effort. Conclusion, There was some kind of imperfection with the threads in the coupling that messed up the threads on the initial installation of the anode, which made it nearly impossible to remove. Whirlpools quality control stinks. The next one will NOT be Whirlpool.

It works quite well except if you put items in the back of the top shelf of the refrigerator it will freeze them as if they were in the freezer section. I have a bottom freezer and that works quite well. And it is very quiet when running.

We bought a new Whirlpool side by side refrigerator almost a year ago based on good reviews. There are many things that we love about it; however it has had ongoing problems and the the latest one cannot seem to be fixed despite multiple repair calls by two different repair services. The service center has been responsive and even extended our warranty but we are getting tired calling them and having repair people in our home. At what point does Whirlpool consider its appliances to be lemons and replace them?

Whirlpool Quiet Partner II Model # DU1055XTUS1 - We bought the dishwasher in Aug 2010 and after the 2nd yr, it started to occasionally shut off by itself in early cycle. After 3 yrs, it now shuts off repeatedly... needs to be restarted at least 15 times. It use to shut down early in the cycle. Now it shuts off whenever. I should have read the reviews on this dishwasher before buying but it was on sale for such a good price. I guess I got what I paid for. Just keep in mind that Whirlpool dishwasher seem to last only 3 years. I guess thats also why their warranty for electrical parts is one of the worst compared to other brands.

I purchased a Whirlpool dishwasher and have had it repaired four times so far. Last time they replaced the main computer located in the door. I attempted to use the dishwasher tonight and it is completely dead once again. I usually have had good luck whirlpool appliances. After all these problems will no longer be using this brand. I contacted the store where I bought it from, Famous Tate. The first time it stopped working just a month after the manufacturers warranty ran out and they were absolutely no help. So in the future, I will no longer buy any type of Whirlpool appliances.

We went out and bought the new front loader washing machine and dryer. Neither one of them works correctly. A service call had to be made the the day we ran the first load. The washing machine only washes errors popping up F8 and E3. On the dryer error code E3 pops up and cannot dry clothes. Worst purchase I have ever made.

Pathetic pathetic service!!! Unsatisfactory service!!! First of all, I would like to tell everyone who ever reads this, that please please please never ever use any Whirlpool products, as their service sucks, their response sucks too, and zero co-operation from their people, which will make you regret to have used their products in future. Please note I registered a complaint on the whirlpool no. **.The complaint was that the washing machine used by us had issues, the power button/ on & off button had come out, and this was clearly stated while registering the complaint. I get a call from Mr. ** (Representative of shree enterprises bibwewadi, pune) and the power button issue was well informed to him as well over the phone by me. He arrived to our place without any new material, he sees the machine and interchanges the buttons, i.e. the broken power button is replaced by other button from my machine which was less used compared to the power button. I had to pay a sum of rs. 400/- for the pathetic service I received from your end.I expect a response from your side within next 4 hours, or I might have to escalate this issue!!! (Please note Whirlpool team that I had submitted the same on your website yesterday, yet I have not received any response from your side). (Whirlpool rating- 0 out of 100). Thanks. (And whoever reads this, please tell me where else can I post this review of mine so that I shall alert everyone that how bad whirlpool service is)...