The fridge had been leaking just a little for a while until the leak picked up and left a puddle. Turns out this plastic tube connector cracked. Seems a very poorly designed fit that caused the bend in the plastic to rupture. Now the whole tube and what I think is the water inlet valve will need to be replaced.

Recently had a Whirlpool gas water heater installed. Would smell gas every time the heater kicked on. I inspected the vent, all the new fittings, with no luck. Leaving the windows open didnt help. Finally found the problem: the factory-installed line from the gas control valve to the tank was leaking. Should have kept my old heater. It was still working flawlessly after 20 years. You would think a new heater would at least be inspected before hitting the market.

I replaced my 12 year old Whirlpool double ovens with the current Whirlpool double ovens. The new 30 built in double ovens have been re-designed to vent the heat below the lower oven. The ovens come with a part that pushes the heat down instead of straight out. My built in ovens have a cabinet drawer below and after using the ovens just 4 times over the holidays I noticed the heat is damaging the finish. According to Whirlpools service center I should have checked on that before buying/installing. They told me to stop using my ovens, that this is a fire hazard, but they are not responsible. They do not have a solution to this problem. This is a poor design on their part. There is a disclaimer in their installation booklet that came packed with the ovens that the installer gave me. It says the cabinets need to be able to withstand the heat of the ovens. The cabinets can handle the heat of the ovens, just not the hot air venting directly onto the cabinets below the oven. Where does one find cabinets that can withstand 400 degree heat being pushed directly onto them? As a customer I did not have that information until after the ovens were installed and it was too late to purchase another brand.

Do not buy this washer. It does not get clothes clean. I use extra rinse (that negates the water savings) and still clothes comes out with stains on them. Some clothes are not even fully wet when removed after washings. I find myself soaking and pre-treating many items. White socks and undergarments are grey soon after buying. I always liked Whirlpool washer and dryer products, but this is a very poor product.

We bought a Whirlpool range with glass cooktop and convection oven to replace a 20 year old stove which had served us reliably but was beginning to look a bit dated and worse for the wear. The new range was installed in February, less than 2 months ago. Today, while I was preparing Easter dinner and had a ham in the oven, the cooktop elements refused to heat, even though the cooktop on light was lit up. We followed all the troubleshooting tips we could find in the user manual and online, but nothing worked. We decided to do the rest of the meal in the microwave and just finish the ham in the oven (which had been working). Then the oven failed, and would not heat back up.As a last resort, we pulled the range out and unplugged it, to perform a hard reset of the electronics. (This was recommended in some of the online troubleshooting tips.) No joy. Both the oven and cooktop elements will not heat, even though the lights on the control panel light up. Now we have to call a service technician to come fix it in the middle of a pandemic. How can a brand new and expensive range be less reliable and less useful than the cheap 20 year old stove we just got rid of?

Purchased my Whirlpool Duet front load washer WFW9150WW00 new in 2010. Also purchased extended warranty. After four years, just before my extended warranty was up, the entire inside needed replacing (drums, bearings). Now at only five years old, it keeps making a beeping noise in middle of wash cycle and wont continue working. Serviceman was told by a Whirlpool tech. that it could be two things, one being the door jamb, the other being the control panel. Door jamb was fine. Ordered new control panel ($240), had it installed and yet the washing machine still keeps beeping and doing the same thing. The serviceman doesnt know what else it could be. So, I am forced to return the part and purchase a new washing machine. I would never recommend Whirlpool to anyone!

I bought these products 2 1/2 years ago along with a dishwasher and Microwave, all which are Gold Series. The first month my Microwave broke. Instead of a certain part that they used to use, they now use a Capacitor instead and it broke. The repairman fixed it under warranty, but told me Ill be seeing you again. Then, my oven occasionally says Function not available. Whirlpool wont tell me what the problem might be and they have nothing for troubleshooting this problem in their manual. My only solution is to reset the circuit breaker and then it works for awhile. Now, My refrigerator has ice building up at the bottom of my freezer and leaking all over my floor. I found a Whirlpool bulletin online which explains that this problem is because of a defective part (Grommet) and that they have a replacement part for it and you can get it by calling their customer service department. Why didnt they send out recall notices to their customers?So, on 8/10/2015 and 8/11/2015 I tried getting this new p-trap part, but for two days now Whirlpools computers arent working and they have no other way of looking this stuff up. Very poor customer service and I also waited for a half hour on the phone to be told their computers arent working. How about putting a message on their pre-recorded message letting customers know their computers arent working?

After reading all of these reviews, Im not surprised at the negative comments. My husband and I owned a Whirlpool washer and dryer for 25 years prior to them both dying the same summer four years ago. I absolutely would not purchase anything but another set of Whirlpool washer and dryer because of the longevity of our previous set.We bought the Cabrio set 4 years ago this summer. After two years, we discovered it had a slow leak at the back hot water valve and underneath it somewhere when it spun and it had slowly leaked under the wall into our living room which eventually caused our hardwood floors to buckle. We had to replace the flooring in that section at a cost I will not even say and had a repairman come out and fix the lid lock, leak where for some reason there wasnt a washer in the valve area, underneath and the problem with the spin cycle. This was at a cost of around $200.00. Of course our one year warranty had run out. The next year it did the SAME THING AGAIN!!! Although we caught it quicker, we STILL had to replace a small section of hardwood flooring and have the machine repaired yet again at the tune of approximately $200.00. Now, as I type, our machine has yet again flooded our laundry room one year later and I will have to call a repairman in the morning yet again! Its becoming an annual and costly thing!!!I came across this site while looking to see if by chance this machine had been recalled and we would be able to get another one at no cost since we have already paid a fortune for the errors it has caused. I will be reporting to the Better Business Bureau and writing YET ANOTHER letter to the Whirlpool company with the hopes that they will recall this machine!! If enough people protest and report this shoddy workmanship, maybe they will!!!

My 2 year Jennaire (made by Whirlpool) broke down on 12/14/11. Repairman came out on 12/19. He said that the compressor was not working and ordered another and he came out again on 12/22. He said that it could not be fixed (internal leak or something). An aside to this story was that a tank of compressed oil blew and damaged my hallway and kitchen walls and floors and 2 rugs. That was being handled by the repairmans insurance company.We called Whirlpool and they said that they we could pick out a new refrigerator priced at no more than $2399 even though we paid $2799 for the Jennaire and would have to pay the difference for a model costing more. We went with a Maytag (Whirlpool product) that listed for $2899 but was available at 2 local stores for $2050 and $2100 but I had to give Whirlpool anther $500 because they use the MRP.They finally delivered it on 1/5/12 but would not leave it because no one disconnected the water line to the appliance and they would not touch it. It took me 20 seconds to do it and if they would have told me so it would have been done on the 5th. Rescheduled delivery for 1/8/12 and the unit was delivered damaged (large dent in front) and they would not temporarily leave it until a replacement came.I called Whirlpool again and asked them to just call a local Home Depot or anyone in my area (all had the unit in stock) to deliver one but they told me that it must come from the warehouse in Michigan (I live in PA) and that it would be yet another 5 to 10 business days to receive it. So, I am paying $700 more for a unit that I could have bought and had delivered before Christmas not to mention the inconvenience of no unit for a month. Not to mention the damage to my home, $200+ dollars in thrown away food, time to shop for new unit, time for 2 repairman appointments and time for the 2 deliveries thus far and countless phone calls to Whirlpool to get the new unit.Today is 1/10/12, so I guess Ill have by month end if there are no other problems, you would think that they would try to expedite this just because its been so long or give us a substantial credit for all the trouble. Never again Whirlpool.

We have had a Whirlpool Refrigerator since 2004. We have only had minor issues with the ice maker within the last 3 years. We have had no major problems with this refrigerator. The other minor problems have been the quality of the drawers. After 15 years the plastic started to crack on them.

In November 2014, I purchased a Whirlpool 22 cu ft side by side refrigerator from my local appliance store. During that short time, there have been 4 instances where the ice clumps together and gets stuck, causing a large amount of ice to dump inside the freezer door. When the door is opened, the ice falls out onto the floor. I usually spend 10 minutes picking up ice and wiping up my kitchen floor. I have had the local store repairman over. He told me that was normal. Two things are seriously wrong with that statement. When I spend 1600.00 for a brand new appliance, I should be able to depend on the fact that it will function in at least a somewhat acceptable manner. Additionally, that statement by the repairman convinced me that he was not really interested in fixing the problem. I really dont think the normal operation of a new appliance is for it to make frequent, large messes for the owner to clean up. This appliance is junk and you would be foolish to purchase it. Spend a bit more money and buy a Samsung or LG. Save yourself the frustration and sense that you have been cheated and deceived by Whirlpool. I will never buy this brand again.

I havent had my Whirlpool Cabrio washer for even 5 years and I have had to replace the glass lid and now the tub bearings need to be replaced... I have read countless complaints for the same issue. I feel like Whirlpool should at least send out free replacement bearings and the $85.00 bearing press tool that you will need if youre handy enough to fix the problem yourself. PS to all of the poor victims of Whirlpool bearings, go to Amazon and you can buy the bearings and the tool for about $150.00. You will need to order bearings part #10435302 and the bearing driver tool #w10447783... And as far as my matching dryer - knock on wood - it still runs great.

Purchased a new French door Whirlpool fridge May. It replaced a Whirlpool that was here when we purchased the home. Ten days after purchase the fridge went to 21 degrees and began freezing over food and drinks. Yesterday a tech replaced parts to repair the fridge. Today the fridge is once again at 21 degrees and freezing food and drinks. We live in a relatively rural area. Tech cant come back until six days from now. Very disappointed. Wish we considered another brand.

My new Tridel Condo came with a brand new Whirlpool washer and dryer and the washer has not been working well since the beginning. After several service calls the repairman finally gave up and now were getting a new replacement. However its been a nightmare working with them trying to get this washer replaced. The Whirlpool delivery team and the service team cant seem to coordinate a time together for the replacement. We had to make a first appointment for the service guy to uninstall the old unit, the second appt for the delivery guy to drop off the new unit and pick up the old and a 3rd appt to install the new unit. Each appt has a 4 hour wait window. This is their standard procedure, which is totally inconvenient to customers. To make matter worse, the delivery guy came too early for a condo delivery (before 9 AM) and told us he will be back the next day. And he didnt show up. It looks like now we actually have to have 5 appts (including the 2 missed appts by their delivery guy) to have the washer replaced. All the time I wasted waiting for this delivery is worth more than the washer itself. What would be 4 hours X 5 appts = 20 hours. This is the worst customer experience ever. After 3 months of constantly calling Whirlpool and still no washer. Whirlpool needs to hire some competent people who actually care about servicing their customers.

We built 8 years ago, with ALL new appliances...All Whirlpool Gold...been very unsatisfied with ALL appliances... Had to replace range and parts for refrigerator..And extendend warranties all nonusable..We live NM off a tarred county road by 1/4 mile...no one wants to even come and look. Not good.

Love love love my Whirlpool range!!! Regular bake and convection!!! Huge oven, beautiful glass top, and 2 burners that have double surfaces to fit huge pans! It has steam clean feature too!!! Incredible and amazing price!!!

Purchased this refrigerator, Model # WRS965CIAH on October 3, 2014. Paid extra for counter depth. Initially the refrigerator worked fine. After about 9 months we noticed the food in the back of the refrigerator especially on the top shelf started freezing. This started getting worse over the next 2 months. When I called Whirlpool 10/19/2015, 800-253-1301, I was told by their representative that this was normal, that air from the freezer blows into the refrigerator through vents and to just re-arrange my food so that it is not pushed to the back of the refrigerator. I asked him if this was normal why wasnt this happening in the first few months but only developed later? He had no answer. I asked him if it made sense if this was normal then everyone who buys this refrigerator has to make sure their food is not pushed to the back of the unit, then why dont they state that in the directions for use??? Ok everyone make sure every day you push all your food to the front of the unit so it doesnt freeze ridiculous. He just said thats the best thing to do. I asked him if I could talk to a technician, if maybe there was a way to fix it manually and he said there were no technicians there. I asked him if he knew about the lemon law and he said they dont have that there... ok. The refrigerator is just days after the 1 year purchase so he basically said just to call where I purchased it that Whirlpool could do nothing for me. Is this how Whirlpool trains their employees??? Good job Whirlpool, way to go. Luckily I purchased the extended warranty. Will see how the repair goes and report back. Did not call sooner due to health issues. Its not like the refrigerator is years old and started to break down - this is within a year. Whirlpool doesnt care about quality. Will never buy Whirlpool again and will spread the word as often as I can.

I bought my Whirlpool over the range microwave WMH32L19AS November 28, 2015. We started having problems with it, working intermittently one year later. I called Whirlpool in January 2017 and they told me it was out of warranty and it would cost $150.00 for a repair person to just look at it. I decided to just keep using the microwave because I only paid $232.00 for it and I figured after parts and labor if would probably cost over $200.00 to fix it. I called Whirlpool back in June because the microwave wouldnt shut off and even kept running when you opened the door. Whirlpool sent out a repair person at no cost to fix it. But the repair person told me Whirlpool only paid for him to diagnose the problem. I had to pay for the repair. After working on the microwave and replacing sensors and fuses he determined the microwave irreparable. I called Whirlpool back and they just told me that my microwave is 1 1/2 years old and they were not responsible after 1 year and I should have bought the extended warranty. I will never buy another Whirlpool appliance again.

I have a Whirlpool Gas Water Heater, product #0733136, that was installed in 2010. The pilot has repeatedly gone out and had to be re-lit. After reading some of the comments, I am amazed that other people were told to verify gas supply with the gas company (done) and clean the air intake (done) and then to call customer service and be told to do the intake cleaning again (done professionally six days ago). I will never buy another Whirlpool appliance, and fortunately, I am in property management and can advise others to avoid this company as well. I am extremely disappointed in Lowes for not doing a better job of providing reliable choices for their customers especially after these many complaints over the years. I have decided to replace the water heater with another brand immediately.

Whirpool Part #WPW10564292 refrigerator handle - I am a property manager who has 264 units. We have only been open for 1.5 years and have had to replace 30-40 door handles because they crack at the top where screws are. We tried calling Whirlpool Customer Service because obviously this is a defect and she said they looked in the system and didnt see any recall or issues. We also asked for a representative from Whirlpool to stop out so we could show them the issues and she said we have nobody in the area. We have 9 service requests outstanding that need a new refrigerator handle. On July 19th, we ordered 3 handles from our distributor and we were told theyre on back order until September 6th. When I called at the end of August to make sure we were on schedule with delivery, I was informed they are now on back order until November 5th. I just called our part rep. this morning and now they said the current part number does not exists and gave me the new part # W11026870, and they are on back order until mid or end of November. I am not going to keep quiet about this issue. We have paid $79.89 per handle on a refrigerator that is only a 1 to 2 years old appliance. I am requesting a returned call or email on what you are going to be able to do for us. This is not right or fair to a company that spent a large amount of money to have your appliances in 264 units.

This is about my Whirlpool Cabrio top load washer machine (model number WTW6200SWD, serial # CT3670597). I bought this machine in 2007, and soon after, I was having problems with the F1 code. After several trips back and forth to reset the code, so I can get the laundry done, and many frustrations, it was time to call Whirlpool to resolve the problem. I find out that there was a recall for this ongoing issue. They sent a technician to replace the mother board, and everything was fine for some time. Soon after, the machine was giving us more problems with the F1 code, and the UL code. It doesnt matter which way I try to balance the load. This piece of junk will not work. Whirlpool needs to stand behind this issue, and recall this washing machine for good. Every customer should be entitled to a full refund, and a compensation for the many hours of electricity, aggravation, and frustration, wasted trying to get this junk to work.

We bought the Cabrio washer and dryer on June 2008, and it wasnt very long after that, that we had to have a repair done. Then, it started twisting the clothes and the sheets into a big knot. Two king size sheets and 2 pillow cases got so twisted that they are no bigger than a watermelon, and believe me, they are very hard to untangle when they are soaking wet. The machine in the drying cycle sounds like a commercial jet taking off. We can hardly talk above the roar of that thing. I hate it with a passion. Whirlpool used to be all we bought, but that is going to change.Linda

The damper switch at the top of my water heater, one I purchased at Lowes stopped working. I talked to someone at the local store, and I was told I had to contain the manufacturer. I called the number on the front of my unit. The tech talked my husband through the restart process...not once, but on two separate occasions. We were told that because it was intermittent, something they decided Over the Phone, they could do nothing. They would neither send a replacement part nor a technician. By the time we had to call back two days later, restart was impossible. JUST to get the part, a specialty piece, we now have to pay for expedited shipping! And either install ourselves, or wait 5 days After Arrival (!!), to get the stupid thing fixed! If they had sent the part out originally when we asked, we wouldnt have to wait for hot water or pay anything for a warrantied piece! Its a racket. Stay away!!!

DO NOT purchase a WHIRLPOOL hot water heater!! The gas valve temperature sensors on these units are faulty. Our technician has replaced several of these defective sensors. Costs $250.00 to install - water tank is only a year old! WHIRLPOOL REFUSES TO ACKNOWLEDGE THIS PROBLEM!! We bought this particular unit because of the reputable name brand. They dont live up to expectations. Dont waste your money on a Whirlpool - youll be replacing it soon! Very disappointed in this company!

4 years ago, we purchased a Model UMV1160CW-3 over the range microwave. After 14 months the door cracked around the handle and eventually fell off. We made the HUGE mistake of buying the same model for ease of installation thinking that this would be a typical issue. We purchase another duplicate model in April of 2016 and less than 16 months later the same issue occurred. Spoke to customer service on 12/28/2018 and they told me that they would pick up the cost of the parts but I would be responsible for labor which actually exceeded the cost of the microwave. Exceedingly poor-quality product and support. Will not purchase another Whirlpool appliance.

I bought a brand new Whirlpool washer and dryer set -Cabrio- $1700.00 in 2011. It is by far the worst washing machine I have ever purchased, and I am 60 years old!!! It is now three years old and has been repaired at least 4 times. Long story short... after hours & hours on the phone, along with many threats! (By the way I had to ask for a manager two times up the ladder for this to happen as they just kept repeating that it was out of warranty coverage). I also told them that I was going to have one of my company trucks deliver this machine to Sears lot, along with a paid person to inform every shopper of my plight with this washer and the lack of service from Sears and Whirlpool! Whirlpool finally agreed to pay for the parts but not the labor on this most current repair. (This time it is the transmission!! In the past it was the Hub, twice. The gear case twice and the belt a number of times). I am now going back to Sears to request (that might not be the correct word) Demand, that they take care of the service bill for this machine. In between repairs, I have dealt with ongoing cleaning quality problems. This machine does not get clothes clean. I always have to wash them twice. This machine is loud. This machine does not use enough water to even dissolve the soap. So much for energy saving measures when you have to wash twice and still see soap and crud in the tub. Worst, worst, ever washing machine in my life!! By the way, I have an 8 year old Maytag too that I have never had to repair. Moral of the story, buy Maytag, or at least do not buy a Cabrio!!!!

7 months ago we had a Whirlpool dishwasher installed into our home. While away on vacation the piece inside malfunctioned and caused major damage as water filled the home. Whirlpool claims, that because it’s a part that they contract out to another company, they “Whirlpool” are not responsible! If you purchase a product from Whirlpool and they put their name on that product, then Whirlpool should stand by its product. Well... beware, you’re not going to compensate from Whirlpool! We urge you, make sure of whom the parts of the product your buying from belong to, before you buy it FIRST! Never again!

I love the French doors with the ease of seeing everything when you open the doors. The only thing I do not like about this unit is the ice maker. If there is more than one person in the household there is never enough ice. Also the ice gets hung up inside the ice maker often.

Dont know the model but it is a basic smooth top range without self-clean option. Its easy to use. I like that it has a smooth top which is easy to clean. I didnt need to pay for the self-cleaning feature as I use an oven liner and clean it right away if I need to. When we went appliance shopping, we needed to replace all major appliances. We chose Whirlpool as we have had them before and they performed well. Also bundling a group of them allowed us to get a great deal.

I have a two year old Whirlpool dishwasher. The soap dispenser cover broke shortly after the warranty ran out. It cost 100.00 for repairs. A year later, it broke again. I sent a letter and the part to the CEO of Whirlpool. They sent a repairmen to fix it free of charge. When you have a problem with a Whirlpool product go to the head of the company. If they get enough calls they will make better parts. Call 1-269-759-6919. Write a letter, return request receipt. It takes a little effort, but it helps a lot of people.

We have a Whirlpool range that was produced for Kenmore (Sears brand). It’s a glass top with electronic controls. Over the 13 years we have had this range we’ve had to replace the controls 3 times at a cost of over $300 each time. Each time we were under severe lightning storms and got hit with a surge. It would burn out the Control board. We finally got a whole house surge suppressor since a large device is required for 240 volt appliances. Also the glass top has gotten scored over the years. We would not recommend this oven and will likely replace it with an industrial gas stove with manual controls when this one dies or gets too expensive to repair.

Updated on 07/30/2021: On 5/4/21 a tree took out a neutral on the power line to my home and after inspection by my electrician, he said my Whirlpool refrigerator was done. Not even 1 year old. When attempting to get Whirlpool to replace the refrigerator, they said they have to try and repair it before considering any other options. As they do not cover damage by acts of God their warranty would not cover replacement. Mind you I paid around $1500 for my refrigerator and it was not even 1 year old. 5/17/21 (2 weeks from when the refrig got fried and I had to get and I had to purchase a used refrig until then) serviceman said he had to order parts. 6/1/21 - Motor-Cond $158.20, Fan Blade $13.97, CNTRL Elec $60 CORE [PI] $497.45 and Evap Fan Motor $183.91. Did not fix the problem and had to order more parts. 6/8/21 - Evap Fan Motor $183.91 (first one did not work), Rail $34.76. Service tech said to wait a bit before moving the frig back to make sure it was cooling properly. Finally moved it back on 7/7/21 and hooked up the water line. Few days later noticed water leaking from the top of the freezer door and a lot of water on my floor. Heard a funny sound and found water spurting from the top 2 corners of the freezer door. Called whirlpool warranty and was told they would contact me. Next I get a notice that I have a service appointment in August. Was able to get it moved with a follow up appointment with a part that was broken during the last repair for 7/28/21.7/28/21 - Fill tube heater for icemaker was open and frozen - now tech ordered Rail $34.76, Freezer Door $1,525.84 and Valve $124.23. 6-8 weeks custom order. So we also have to added 5 service calls to the cost - Approx. $500++. Total Replacement Parts = $2,758.81 with a final total cost to repair of $3258.81+ vs just replacing or reimbursing me for the appliance of approximately $1800. Someone needs to review their model because not only am I without a working refrig for 4-5 months, but the repairs cost them $1500 more and now they have a customer who will not longer invest in Whirlpool appliances because of bad business practices and inconvenience.Original: I purchased a Whirlpool side by side refrigerator in July 2020. Earlier this month I had a tree pull down a power line and disconnect the neutral, allowing a full surge of power to go through my house. It fried the exhaust hood, literally melting the components. It also fried my refrigerator. The electrician who reconnected my home signed an affidavit that the refrigerator was permanently damaged due to the surge. When contacting Whirlpool to file a claim, I was on hold over an hour before getting a person. This happens every time you attempt to contact them, so patience is required. I was not able to get a service call on my refrigerator for 2 weeks (5/17/21) so that left me without a refrigerator. The service company showed up early and I had no choice but to leave my job or reschedule another 2 weeks out. The tech said he could only repair and made an attempt to contact Whirlpool to get the unit replaced and he was on hold for over 30 minutes. They declined and said because it was an act of God they could not replace it. I was already having issues with the unit before the surge of a constant defrost that was causing food to spoil due to melting then refreezing causing freezer burn. I also lost over $500 worth of food. They dont cover. It also caused the icemaker to constantly freeze up. Now it will take at least another 2 weeks for the replacement part to fix and a refrigerator is not something you can go without that long. I had a concern this would happen. When speaking with customer I service, they said they just needed the tech to confirm it was damaged to replace it. At this point he said he does not know if the piece (on 2 weeks backorder) will fix it. They can only tell after the fact. He said Whirlpool only fixes and does not replace, which is not what Home Depot informed me when inquiring into the warranty with Whirlpool. They said Power Surges are covered. So with this in mind, I would seriously consider buying from Whirlpool. Things break, situations happen and no one should have to go without a refrigerator for over a month because they may be able to fix it. Then there is the concern if something is melted/destroyed inside, if it could cause a fire in the future. Will never buy another Whirlpool appliance again. They cant stand behind their products, the products are worthless. And yes, I am very upset. Again - just had Whirlpool tell me its not covered as it is an act of God! ARGH -

The 2 rear steel rack supports were flaming/sparking. I was told by Whirlpool over the phone that this might have been a recalled item, but they would send a technician to check. The technician said it was a build-up of grease and that I should not have used the rack and not to use the rack at all in the future. However, I do not use the microwave often enough to get a build-up of grease and it is cleaned thoroughly. This is a Whirlpool-manufactured product. Why would it be unsafe and why can I not ever use the rack again? If this was a hazard, why has it not been recalled?The technician removed the rack and sprayed a white substance on the support, and I was charged $138.03 for this and left with a partially, unusable appliance. I would like this to be replaced, so that I can use 100% of my microwave or be reimbursed for this expense. Please explain. Thank you.

I purchased a stainless steel side by side refrigerator and unbelievably the doorshelves came crashing down - they just cracked in the middle. How cheap can stuff be made, those fridges are not cheap. I thought Whirlpool was a good product - I guess not.

Just like a lot of other people, I bought a Whirlpool hot water tank because of the good name. And just like the other people, my tanks pilot light will not stay on, it will be on for a few days and then you get up and no hot water.

Purchased a house and old owners left an almost new one with house. Thing does not clean even minor soiled cloths. Plan on buying new machine directly and it will not be a GE or Whirlpool. I can see why they were willing to leave the new washer. I left a 15-year old Maytag at my old residence (wish I had it back).

Pros: The refrigerator is large and roomy, easily adjustable glass shelving, and easy temperature controls for the refrigerator temperature and freezer temperature. Cons: the refrigerator is bulky and limits space in a small kitchen. The lower freezer door does not seal very well and requires frequent tweaking and adjusting around the door seal. Also, the freezer handle becomes loose easily and requires tightening fairly often -- which is a pain to get on the floor on your back (and a flashlight plus a special wrench) to tighten the handle.

The Whirlpool engineers need to go back to design room sober on this machine. It is only a year old and still I have to run one load two sometimes three times just to get clothes clean. How is this energy-efficient? I have tried all of their so-called remedies. Paying such good money for a lousy and lazy appliance is hard to swallow!

I bought the HE Whirlpool Cabrio 2 years ago. It has all the bells and whistles, fancy cycles, etc. but doesnt clean ANYTHING. I have to wash three times to get things clean... So much for energy efficiency. It also gets out of balance with larger loads. What a waste of money and time.

I bought my Cabrio Platinum Washer and Dryer in 2013 (4 years old). About a month ago, it started sounding like an airplane was landing in the house while on spin cycle. I called a repairman and he said the bearings were going bad and it would be better to buy a new machine. When we pulled out the washer, there was grease all over the floor - apparently a seal started leaking and the bearings had no grease so they started burning up. I talked with Whirlpool, after all it was only 4 years old and a seal leaking and burning the bearings up wouldnt be from normal wear. They were not convinced and offered to give me a discount on a new one -- No Way! I went with another brand recommended by the repairman. The screws on the dryer door also came out and we had to replace them. So much for the Whirlpool brand and especially their top of the line machines. I will not buy another Whirlpool washer or dryer.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

We bought our washer (Whirlpool Cabrio) from a rent to own company about 2 years ago, and finally got it paid off. About a week ago, the lid started sticking when it was done washing. I went to open it last night to start some laundry, and it BROKE. Now theres a piece stuck in the bottom part of the lock, and the washer wont start. Anyone else have this issue?

How would you like to be without a refrigerator for 10+ days? How do you justify 10 days without a service tech being available for what I call an emergency! Either you need to hire more technicians or make BETTER products. My suggestion is have a supervisor go out to a call first and access the problem. My case, a tech shows up after waiting 10 days, to tell me my refrigerator needs all the parts. Which means Ill have to wait probably another 2-3 weeks for the parts to arrive. Im sure the parts werent ordered to be expedited. Im beyond furious. We lost everything in our freezer. Doesnt stay frozen in coolers.When we purchased the refrigerator, just under two years ago, the service tech was out three separate times because our ice maker kept going on the blink. Finally, I purchased ice maker, because your refrigerator only makes ice when it wants. Not reliable! Second problem, the lights in refrigerator & freezer went out. Real smart to install LED lights that can only be replaced by a technician. Insane for the consumer. (Cost of lights replaced w/o warranty contract is $100). DONT BUY WHIRLPOOL PRODUCTS UNLESS YOU ENJOY MISERY!!Why would you put glossy black finish on front of refrigerator, and the sides have black texture, where you cant see fingerprints. Has to be cleaned daily! Hope you can rectify the problem before two more weeks pass. Model: WRS322FDAB. SERIAL#: HR72710418. Not a fan of your lemon of refrigerator. You can also view this on your customer reviews WHIRLPOOL.

Whirlpool Refrigerator Freezer WRF560SEYB01. Purchased the Whirlpool Refrigerator Freezer in 2012 at Sears. Ran okay for 2 years. Bottom freezer door came off the track. Called Sears. Sent out repairman for $200 to replace the door. He did not check the ice buildup on back of freezer. Next problem, severe ice buildup, loud noise. Used hair dryer to melt ice and took the blower fan out of freezer. Solid ice on all the blowing fans and found a chunk of solid ice. Freezer no longer made the noise until the ice built up again. Now, it continues to build up and we have to use the hair dryer every two weeks. A refrigerator should last at least 10 years. This model doesnt even warrant a rating of any kind.

N40T61-343 Whirlpool Hot Water Tank - Purchased this hot water tank and had problems keeping lighted. This hot water tank has never worked correctly, every week the burner needs removed and cleaned or the flame burns under burner. The wires burn up and you need to buy a new burner. I have bought two new burners and am fed up trying to have hot water with this Whirlpool unit. The gas company has been here three times, they blame a poor design.

My old 25 yr old Whirlpool died and was shopping for a new one. I saw the Cabrio and was really impressed by the features and large capacity interior. I can say that I thought my clothes were getting clean until I looked closely. I have never been so disappointed with this washer. I wish I had my old one back! Clothes arent clean, they are so twisted when I take them out and theres a horrible smell, like oil burning when it runs. The machine would fill up and when it would start to wash, it wouldnt, it would stop. And a loud humming noise was coming from the back.I shut it off and turned it back on and it wouldnt clear. I had to unplug it and plug it back in to clear it and start over. The bearings are gone now and I was going to have a repairman come and look at it, but now I wont bother! After reading everyones comments this Cabrio is a piece of junk and Im sorry I ever bought it! So now Ill be shopping for a new one tomorrow with an agitator!!! Im not impressed with the HE appliances!!! Ive owned this POS for not quite 6 yrs. Expensive to purchase and I will not recommend Whirlpool to anyone! Its sad that companies today make cheap products!! Built to last... ha!! Well never see those again!!

I purchased Whirlpool 6.2ct electric range on 3/16/2013 from Lowes, Fremont, CA. I tried to bake my cake on 11/19/2013, and preheat it to 400F degree. When the temperature achieved to 400 degree, I put my cake in not even 5 minutes and go to dining room to pick up something. When I turn around, I saw the oven window is so bright and I open the door right away, it has fire from the left side bottom. I turn off the power right away but still has big fire. So I use the fire extinguisher to get the fire off.I went to Lowes to complain, this product is still under the manufacture warranty and I also purchased two years extended warranty from the store. Lowes sent the 3rd party technician over to check, they open the bottom element and insist I drop something to catch on fire. He tried 350F degree is working. But the fact is, theres nothing dropped, no oil, water or and any ingredients, only fire extinguisher powder all over the bottom. Technician put back the cover, I asked him, How do I clean up the bottom extinguisher mess? He said, You dont need to, just clean the top, and wont try 400F degree for me since the top didnt clean up. I asked him, I am so fear to use it now, you asked me to clean it up and try again. I only use my oven to bake cakes, cookies, and muffins, and that day the cake even not still raise yet. How could it catch on fire? Is this product defective? I doubt it.I also called Whirlpool, they said most likely its short circuit. They only provide the repair, unless it cant be repaired, then they replace it. Manufacturer also told me that my temperature is high. I dont think so. I have no problem to use any oven in 425-450 in the past. If this is high, why your stove has function to that high degree? I am so upset with both services. From my concern, nothing dropped to bottom and caught on fire. They all refused to replace the new one and asked me to continue using it. I really dont feel confident to use this one and dont know who can help me to replace it.

The Whirlpool washing machine I bought is a piece of crap! I only do laundry every 3 weeks/3 loads and the machine broke in 13 months. Now it has broken a fourth time/same part - I have had the machine for 5 years and they can not do anything about it. I will not be buying Whirlpool again - of any kind.

Whirlpool Gold Series French door, bottom freezer. - This fridge is beautiful. Thats as far as the pros go for it. The Freon is leaking and cant be repaired because of where the leak is coming from. I can always tell when its time for a recharge because it leaks water profusely when at a low charge (every 4 to 6 weeks). We paid over $1800 for this fridge back in 2013. It has been just over two years and we are now having to replace this fridge. I cant express my frustration at this point. Whirlpool wont do anything to help us. They told me, You are out of warranty, and thats all they have to say. Thats over a thousand dollars a year to own this POS when you consider taxes. Over $1250 a year when you consider the service calls along with it. I will not purchase another Whirlpool product ever again. I am disgusted by this company and their refusal to stand behind their product. They have literally stole money from me and are laughing about it. Do yourself a favor and stay far from Whirlpool.

Whirlpool built in Electric oven Self Cleaning Model # GBS307. Dont Clean your oven! Everytime you clean the oven, the thermal fuse switch will burn up on you and will cost approximately $150.00 to fix. Dont use the self cleaning on this oven!

Bought microwave two years ago, almost immediately when stove area got warm, the microwave would not work properly. It would beep, the info keypad would cycle, then freeze up. After unplugging and letting it sit for a while, it would work fine for a time. Now it doesnt work properly at all. We keep it unplugged until we need it then it may or may not work. I have had a service company look at it and the only thing they could figure was that was an electronic failure from the heat. I am concerned that it is a fire hazard and leave it unplugged. Not what I expected from a $1000 appliance. I wish there was a class action suit that I could join.

Ive trusted Whirlpool washers for 20 yrs. Ive only had to buy 2 in my lifetime and neither have let me down. I will always purchase Whirlpool as it is a brand I can trust. Features and reliability are important to my family. Whirlpool has it all!

Bought this Whirlpool washer (WTW5000DW0) to save energy and water consumption. It has been awful from day 1. Clothes come out with detergent (white marks) all over them. Clothes aren’t spun out enough to dry them. It takes FOREVER for a load to finish, I can’t imagine that this is saving me anything on electric. Waste of money. Do not buy this!

Horrible customer service. No help in trouble shooting your the appliance. Whirlpool only wanted to send a service technician. Several things have gone wrong with this dishwasher that came brand new, in a brand new house. After the year warranty is up, forget about any help from whirlpool. I would hope you would not have to purchase extended warranties on any new appliance but that doesn’t seem to be the case. My dishwasher was only three years old and on its way to dishwasher heaven. I was told by a repairman that whirlpool had a problem with their motors. Whirlpool would not confirm or deny this. I felt like I was really taken.

The refrigerator has worked OK except for occasional freezing towards the back. However the vegetable bins have both broken starting with various parts of the handles in front. We eventually replaced them. A brand new one arrive already broken. Same cheap brittle plastic. No alternative available. The company denies any problems or complaints about the bins. Feels like a small profit center for them.

l will never buy Whirlpool appliances again, nor do I recommend to anyone. My wall over was 1 1/2 yrs old with a worthless 1 yr limited Warranty. I had Total Appliance from Cleveland do the repair, the only ones I found at the time that would work on this type over with a Digital panel. I think the engineers think we all live in Silicon Valley. Unfortunately the cost to repair after I cleaned the oven for the first time was $384.00 to unlock the door and 2 trips and he had to remove the door to replace 2 fuses so the door and panel would work! Im afraid to clean them oven again..I called Whirlpool and the first wait time was 70 Mins... I put the phone on speaker, finally I talked to 2 Customer Service men to no avail. He basically said my Warranty was up and nothing they could do! I said I was going to complain on Social Media and he didnt care! Go to Consumers Digest before you buy any new appliance! PS, I also went on YOUTUBE and you can see all the TROUBLESHOOTING ON MANY APPLIANCES!

10 years, no problems with our 25 cubic foot french door Whirlpool refrigerator. Ice maker is a solid performer, with nary an issue. Temperature controls work flawlessly. The black frame looks great in our kitchen with espresso color cabinets.

I just bought a Whirlpool Cabrio Washer WTW8800YC1 yesterday (1/19/14) delivered today. First load never finished, kept getting error of F51, which I looked up and its a sensor. I looked up the review on this washer and it seems to be the census that this washer is POS. Im having the store pick it up and refunding my money. My old washer is 20 years old and never had an issue with it. We just wanted a more efficient washer. Thank Goodness I didnt have the store haul it away.

I love this stove! It is nearly perfect. I wish it was easier to clean the glasstop, but I imagine that comes with any glasstop stove. The stove is easy to use, and I love the cooktime option. My only complaint is that the timer is very quiet, and when it is a timer while something is cooking, it only beeps once. If its a timer when nothing is cooking then it will go off repeatedly until you turn off the timer.

Whirlpool Gold microwave quit heating after little use. We moved in house one year ago, microwave 6 years old. Spoke with Timena customer service rep. She took my model, serial info and clearly explained this model had defects and they would replace for free even though 1 year warranty was up. Delivery staff would call within 24 business hours. After 4 days I call back and get Mia rep, she claims I was disapproved for new unit after all?? I spoke to 2 supervisors above her Karin in Tennessee, and another. They claim I was mistaken??? I said, “Look up the recorded call and you will see the message is clear... They acted shifty and claimed I should buy a new starting at $1399!!! They would consider small discount?? Their rep was clear at first then they failed to back her up. Terrible customer service. Lied etc. Never buy Whirlpool!!! They are cheap and don’t stand behind reps. Awful company!!!

First F1 symbol on washer took 6 months to resolve. All we needed was new motherboard and couldnt mail it to us even though we could replace. It had to be an authorized person. Well we had one and they never put him in the system. Finally got that taken care of, 6 months of having to press pause and restart 5 times just to do one load. Arrrrrggggghhhh! Now water leaking out the bottom. Called again, on hold, then on hold again to be transferred to tech support. Yeah, right. No tech support. Talked to management, they could care less about us even though we have other products from them. Dont buy, they are lemons. We had ropes for 15 years and lasted through everything. Thanks Whirlpool, heres to losing a customer!!!!

Found after care service as bad as oven performance. Phoned for advice and told need to get used to new oven. My advice would be do not buy whirlpool ovens.

Purchased a NEW Whirlpool side by side refrigerator (WRS965CIA) and it was delivered on 2-3-14 with a dent in the door. The retail store ordered a replacement door and this order was approved by Whirlpool. 4 months later, I still dont have the door. My 8 calls to the retail store say that Whirlpools Trade partner is not returning their calls or emails to get this resolved. My contact with Whirlpool was met with contact your Trade Partner. Vicious cycle and still no replacement door.

Whirlpool stove, product ID WFG540HOES. I purchased a whirlpool gas stove in 2014 for a lake house. Came to my lake house to find the temperature was 90 degrees inside and the oven was running full blast. The oven had turned itself on. Whirlpool appears to be having a problem with this type of issue. Called their customer care department and was transferred to the appliance safety line which was only a line to leave a voicemail. Very bad customer service. My kitchen countertops and kitchen floor will need to be replaced, also cannot get rid of the burnt smell in my house. Do not recommend purchasing Whirlpool appliances.

I will never, ever, ever buy a Whirlpool appliance again. We bought the french door bottom mount refrigerator in 2013. After our warranty ran out, we had to have the guts of the refrigerator replaced and then the ice maker replaced again. Now the freezer door wont shut and I cannot believe that Whirlpool would put their name on this piece of junk! We splurged to get what we thought was a high end model but it has been problem after problem. RUN from Whirlpool!

WHIRLPOOL MICROWAVE HAS HAD MAGNETRON GO BAD 3 TIMES IN 1-1/2 YRS! I bought a Whirlpool Microwave Hood Combo Oct 2009. July 2010 the magnetron went in it! December 2010 the magnetron went in it AGAIN! This time we had to pay the labor to have it repaired because it was 2 months outside the warranty period. We did not want to pay because we knew having the same part go twice in one year that something is wrong with it. Whirlpool told us that if it happened a 3rd time that they would most likely replace the appliance for us. Well....July 2011 the magnetron went AGAIN for the 3rd time! Whirlpool told us to take it to a licensed shop to have it diagnosed to prove that it was the same part as the previous two times, fax paperwork from the prior two times, and have the shop call in the diagnosis of the 3rd time. We did all that, and they told us they wouldnt do ANYTHING for us because it was outside of the warranty period! Well they knew that when they told us we had an opportunity to get it replaced! THE SAME PART WENT BAD 3 TIMES IN A 1-1/2 YR PERIOD OF TIME. We trusted that the Whirlpool representatives were being honest with us during those phone conversations. Whirlpool can not explain why representatives would give us hope of a replacement (although each conversation is documented by their login and employee ID number). So not only did I buy a brand new MSRP $619 microwave, I paid to have it repaired the 2nd time, and to have it diagnosed the 3rd time, uninstalled and reinstalled the microwave each time, the inconvenience of not having use of the appliance during each occurance, and the unbearable suffering of calling in to customer service and repeating the story over and over to each representative. My house is brand new (we moved in to it November 2009); we bought ALL our appliances from Whirlpool. All I get for an answer now is sorry. That doesnt help me any financially having to repair and now replace an appliance that has been in use for only 1-1/2 yrs! I have seen $39 microwaves from WalMart last several years, so what is wrong with Whirlpools manufacturing?! Customer Service is unreliable, untrustworthy, non-sympathetic, and insanely frustrating! My question for Whirlpool is...why cant you make a product that lasts better (better quality=longer life=healthier environment and happier customers)? Why cant you stand behind your products better? Dont you care about the impact youre making on us emotionally, financially, and environmentally? The model # is GMH6185XVS0 Serial # is TRY3111264.

Old stove does the job. I need a new and updated one. Need a warming drawer. Lower drawer does not close properly anymore. Paint on back panel is chipping. We are limited to range choices because of space.

My Cabrio is only 4 years old and it stop working properly. I call a service technicians to repair it and after aol $45 service charge level, he tells me that it has a Motor capacitor defect at a cost of $360 to repair. So I have paid useless piece of junk. I out and purchased another washer only $150 more than the repair. I will never buy a Whirlpool product again. My last washer a Maytag (before Whirlpool bought them out) lasted over 20 years. So if you do not want to buy a new $600 washer every 4 years. Stay clear of Whirlpool.

This Whirlpool side by side 2 door Refrigerator/Freezer stopped working yesterday. It was manufactured in 04/2013, and I purchased it from Lowes on 5/26/2013. My invoice number is **. The last 2 refrigerators I have owned worked for well over 20 years each. Actually, longer, but I moved away from one of them. It is unbelievable to me that after 3 years, and 3 months, this unit has just stopped working. Of course, it is coming at a horrible time. In addition, it is summer time in Southern California, so the heat is high, and the desire for cold drinks and foods is also. It had been working well, until yesterday. Today, I am experiencing the foods become warmer and warmer. I will not be purchasing another Whirlpool Product of any kind.

We bought a Whirlpool side by side at the end of August 2017. In March of 2018 - the day after I got the letter about extending my warranty - they had to replace the diffuser - it was making a horrid noise and freezing my eggs and milk. This part went again in July. I insisted they extend my warranty which they did - until March 2019. The part went again in November. I again demanded an extension - now it is guaranteed until June 2019. I asked about replacement and was told that as long as it was reparable they would not replace it. This part is dying every four months. The first few times I called, the hold recording touted a repair app - that did not give me much confidence in the company.

Had washer for 5 months. It now has a door latch error. It has been 3 weeks and it is still not repaired. Parts take a week to 10 days to get. We are now going back and trying the original part ordered. Not sure if this will fix it this time, as it didnt the first time, but we have no choice. Whirlpool will not stand behind their product and give us a replacement and for good reason, it is obviously junk and we will have the same issues in 5 months. Calling their help line is a waste of time, they understand your frustration but do nothing to help relieve it. Their supervisors have the ability to do nothing and excel at it. Thought this was a good product when we bought it but are now suffering for this decision.

I bought this washer less than 2 months ago and I am devastated to say the least as they are not even remotely cheap. Appears that is doesnt come close to using enough water or enough agitation to get even 2 pieces of clothing clean. What good is 5.8cu (largest size tub) if you cant even wash a load sized for non HE washer. I am forced to wash a 1/4 of the amount of clothing now vs my previous standard washer, if I even want half cleaned clothing. I have tried every cycle with no difference.Doesnt use enough water but appears to spend most of the cycle time, filling with water. I know that sounds contradictory, but there isnt really any other way to explain it. Might as well not even have an (agitator), I use that word lightly here, as it does nothing to help clean the clothing inside. Pre-programmed cycles are not enough to do what you need it to do. Because of the pre-programmed cycles, unable to place clothing inside, fill with water, agitate a little and then stop or pause long enough to let contents soak for a while. I really miss being able to do this with my previous Whirlpool washer.It doesnt matter how little or how much detergent you use, the results are always the same, clothing comes out partially dry and dirty. Usually requires 2 or more wash cycles to remotely obtain clean items. Most items never even go under the water, no matter how much water it decides to fill with. I am so disappointed with Whirlpool with this fiasco they call a washer, with their name on it and they should be also. I have never owned any other brand than Whirlpool, so I didnt hesitate to buy this set, as I had wanted them for several years and finally made the decision to purchase and what a mistake this was. Will never make this mistake again. Whirlpool needs to correct this for every customer that has purchased these washers or risk ruining their reputation.

Just bought two new Whirlpool water heaters, $469 each. Not impressed. One of the MANY issues: water leaking from the top. Reason: before installing, if you look inside female threads, you may see a rubber gasket (heat loss valve). One of the two heaters of mine was missing one. This showed me what the quality of the joint was like under the gasket. I temporarily removed the other three (two heaters) to confirm what I saw: At the backside of the threads there should be a clean flat landing from which to the male nipple should tighten against (washer in-between). Instead, there is a disaster of a flimsey lip (washer-like) which is torn up and not anything close to flush. Bad Whirlpool! Bad quality control!

We have had the washing machine about four months. When washing sheets, they twist up badly. The machine does not seem to get the clothes very clean. It seems that it does better when we put it on the bulky setting for all washing that we do. More water is needed I guess.

I purchased this Whirlpool, model YGY397LXUQ04, electric range in midsummer 2011 and used it very infrequently for approximately 5 months as we were away for 6 months during the winter. On approximately June 15, 2012, we found that the keypad would only register 350 deg. F for the oven if we pushed the bake button two times and the oven temperature would go up to 550 deg; F if we pushed the 7 button 3 times. In discussion with the service manager from Whirlpool, he advised that the stove was out of warranty and they would supply parts at no cost but we would have to pay the labor costs which in my estimation would cost over $200. After searching the internet for similar problems, it was evident that this problem was not uncommon. I am concerned about the quality of this product and if it can possibly be a fire hazard. I would not recommend this product as the quality, possible safety issues and reliability are a significant concern.

I have purchased in the past all Whirlpool appliances all at the same time. Washer, dryer, dishwasher, refrigerator, stove, microwave and I have had issues with every product after the first year, from plastic parts failing. That should have been made out of metal, to motherboard replacement. I work Hard for my Money, and when I need to buy a new appliance, I want truth in advertisement of what I am spending MY MONEY on. I would like a product that is built to last!!! If whirlpool cannot offer this we need to COMPLAIN all over the Internet until whirlpool changes their design and uses better parts for their products. I as a consumer deserve this.

Whirlpool Cabrio Washer - This is a horrible washer. I just read the reviews after having struggled with dirty clothes, smelly clothes, sour clothes and yes, our water bill is way higher using this nasty machine. I will never buy a Whirlpool again. Very VERY disappointed and dissatisfied with this machine. I usually always read reviews before buying anything but the sales guy at Garner Appliance said this was an awesome machine. We bought the matching set. And to read each and every consistently bad review with the same issues. They should replace these pieces of junk for us free. The dryer doesnt fall too far behind.

Whirlpool Double wall-mounted Oven model#WOD51EC7AW05. Have had nothing but problems (at least 7 problems). The 1st one is a potential fire hazard. Porcelain/enamel shattered on bottom interior panel of BOTH ovens in less than 60 days (exposing underlying metal to rust). Cracked in an odd stress-pattern that indicates the metal expanded during heating, and the porcelain finish did not tolerate the expansion. The lower oven had only been used 2X before I noticed the fracture pattern. Obviously faulty design; a manufacturers defect. Whirlpool claims it is cosmetic damage and when porcelain eventually flakes off, they will send me touch-up paint. (If I dent the outside of an appliance with my wheelchair, thats cosmetic damage. Its a manufacturers defect if the damage happens during normal operation. The appliance damaged itself, not the user.)The preheat function does not work on either oven. The oven indicates it is 350-degrees, when it is actually 125-degrees. Repairman says this is normal; ignore the indicator and navigate by store-bought thermometers”. The temperature can vary 50 degrees on either side of the actual setting (thats a 100 degree range!). Between the faulty preheat and the wide range in temperature, it makes it very hard to bake bread or cake.The rest are annoying problems: The timer is a single “beep” (not even very loud), followed by another single beep every minute. This is not much help if you are folding laundry while the cookies bake. The windows have so many dots on them theyre not clear enough to see how the food is cooking (or read the store-bought thermometers) without opening the doors. The oven produces a lot of steam that fogs up the windows (Ive never had this happen, and Im past the half century point). The exhaust fan is loud and it blows hot air into the drawer under the oven (another potential fire hazard). Dont buy this oven. It has several design flaws and Whirlpool does not stand behind their product.

I purchased the glass top Cabrio a couple of years ago. Without an agitator; it is amazing how nice thick towels come out with holes or rips! Clothes get so twisted. My sister needed a new washer and after telling her the problems with the Whirlpool; she purchased an LG. I have told many people that have purchased an agitator free machine to stock up on Affresh or one of the other tub cleaners... you need them to keep the odor from getting into your clean? clothes. I cannot wait to sell this washer or give it away!!

I bought the Whirlpool Cabrio washer 2 years ago. It started recently messing up and making a loud noise during spin cycle and gave me a UL code. I called the repairman and he is stating several things need replacing. Cost more than washer did at time of purchase. Bearings and 2 other items need replacing parts. 550.00 plus labor of 250. I will never buy another Whirpool. My previous washer lasted 10 years. I got rid of it for a matching washer and dryer by Whirpool. Worst mistake and Im out a lot of money. By reading all the poor reviews. Seems like Whirlpool would do something. Its a ongoing problem. Many people have reported. I have read many similar experiences and wished I knew before purchasing this set. If you are reading this do not buy this washer and dryer set.

Purchased a Whirlpool range. Shopped around for several weeks before I found what I thought was a good price and with a rebate! Ive owned the stove for 2 months and 7 days... guess what? The stove broke. The burners popped. I called to have it serviced and remember that it had a rebate. I never received any paperwork on the rebate but figured its Whirlpool, good company. Wrong... its not that I didnt have the rebate paperwork but the rebate has expired... even though I didnt get any paperwork nor was there any mentioned of a time frame. Dont get me wrong if it had been 1 year or even 6 months... really 2 months!!! So not only did I not get the rebate of $100.00 I have a broken stove! So tired of being ripped off!

Our 3 1/2 year old dishwasher is falling apart. First the left slider broke on the top rack. We ordered a replacement part ($74) and when ready to install, discovered the right rack was also falling apart. At that same moment, the rollers fell off the bottom rack! It seems the plastic parts cannot tolerate the heat in this dishwasher (just a guess). We’ve returned the new replacement part and are shopping for a new dishwasher. It will not be anything from the Whirlpool line!

Duet Washer GHW9150PH0 - The washer is about nine years old. Last year I got the dreaded F-11 error code, and had to purchase a new controller board and install it. Now the spider arm on the basket has snapped (cast part). Ive been on the phone with Whirlpool for over a half hour now, and all I get is We have to send a service tech out, and you have to pay for them. I have the broken part in hand, I know the Whirlpool part number, yet they want me to pay for a tech to come see the part and confirm it. Ive been unable to talk to a manager yet, none are available.Eventually the lady agreed to replace the broken basket, after telling me at least five times she could not, but she refused to replace the tub which was destroyed when the basket broke. Ill be calling back to talk to another agent soon.

I had one of the first Maytag Neptunes. Loved it to pieces but finally had a problem and my beloved repair guy said it was almost 20 years old so to give up and move on. Obviously, cant be without a washer for very long so grabbed this Whirlpool Cabrio Platinum Washer. One of the biggest disappointments ever! Clothes come out streaked and splotched, dont smell very fresh or clean even straight after having been washed, stains dont come out even with pre-treating, have to run everything on heavy duty, whites are getting grayer by the week, and all-around horrid performance.Im ready to give up my Starbucks, start packing my lunches for a couple months, skip whatever treats I have to in order to get back to a quality machine that can actually WASH CLOTHES. I wondered exactly what it was or wasnt doing so I stood over it for half an hour. Initially, it loads up about a gallon of water and then spits it out over the rotating drum of clothes. Then it stops and spins that water out. I suspect the design logic was that it would force that gallon of water thru the clothes taking some dirt out with it. It repeats that stupid process several times. Then it finally gets a few inches of water in the bottom and the vestigial agitator tries to move it around.I watched one hand towel lie on top like a dead weasel, never getting pulled down or pushed out or whatever it was supposed to do to get down among the other items and squish together. Life throws me everything from sick kids spewing body fluids to people coming home reeking of hydraulic and other industrial fluids. When I say clean I mean CLEAN. This piece of junk couldnt satisfactorily process half a dozen dust rags. Neptune, Im coming back with my hat in my hand and a whole new appreciation!

Over-the-range microwave hood combo - It is not that it does not work, it just wont shut off! Close the door, it turns on. Touch the side, it turns on. I have walked in the kitchen and found it on! I am afraid it will turn on when I am not home and burn down my house! After reading the poor customer service received by others, I will just replace it.

I love my Whirlpool. Were a family of 3 with a pet dog. Its handle one childs work uniforms and the others sports uniforms (yuck). And then theres my work/weekend clothes. Its very reliable and it gets the job done. We have no complaints.

I purchased my Whirlpool side by side refrigerator approximately 6 months ago. Immediately upon delivery the compressor showed itself to be very noisy, especially upon start up. I questioned the delivery persons and was told it would become quieter with time. It did I not. In fact, in the following days it got worse. I contacted Whirlpool and was sent an “approved” repairman. The confusions and scheduling difficulties in this process, however, were many. Finally, when the man did arrive. He listened and said the refrigerator was working but agreed it was loud but apologized there was nothing he could do.I called Whirlpool again several times to note the noise and constantly was given the sympathy of people saying they “understood but there was nothing they could do.” Finally, out of desperation I contacted the store where I had purchased the refrigerator and they sent a manager who agreed the unit was unreasonably loud and took the refrigerator back. I researched the Whirlpool company and found they are essentially the same company that makes several other common American name brands, so I made a point not to purchase from any of these companies. Instead, I purchased from a foreign manufacturer and couldn’t be happier. All I can say is I tried to buy American but have been greatly disappointed by both the product and lack of customer service by Whirlpool. I will not buy from them or their other companies again.

A-10 error on display ultimately means needs a new pump. The washer (model WFC7500VW 2) is 3 months, 9 days old and is now unusable. I cannot get any service (under 1-year manufacturers warranty) because the sticker inside the door with the model and serial # is missing (i.e., it was sold to me by Homedepot.com without a serial # on the door label, sticker is intact and is brand new and apparently was printed without a serial #).I made multiple calls to Whirlpool in Benton Harbor, Michigan and finally spoke with Courtney (who states she was a supervisor) pretty much said all they will do is to reprint a label from the factory and I should have it in 7-10 business days. They refuse to stand behind their product and authorize timely repair of their product they sold to my without a serial # on the door tag from the factory. I have to wait to schedule factory warranty repair until I get the new label (probably 3 weeks plus without a usable washer). Courtney refused to contact me via email for any of her contact information or to supply verification of conversation or promise of a new factory label. Also, she refused to try to authorize any type of manufacturers warranty to fix the brand new unusable washer!

In all of my 50 years of marriage and buying stoves, I have never had an oven breakdown. I live in Canada - I purchased three appliances, all Whirlpool 2 years ago. I had to have a service call on the fridge three weeks ago - a little rubber nipple was clogged up and water was running into my freezer. Bill $100.00 - two weeks ago, the broil element in my stove would not turn off when the bake cycle heated up. Actually, you did not have to press the fast heat button as the broil came on by itself. I have been waiting almost two weeks for the part - today I was told it would be another week. The part has to come from the US - what ever happened to Whirlpool Canada???? - I am told the bill will be $350.00 and maybe more plus the service call. I do not find this acceptable. What do you do when you have already invested the money in the product. Bring back the old Moffat stoves. I would like to be reimbursed for the money I have put out and will put out.

Whirlpool microwave came with my new condo, and its as aesthetically pleasing as it is functional. Very easy to use, sounds are not annoying (as my last microwave was) and heats food quickly and evenly, as needed.

The only thing cheaply made is the push latch on the dryer. Both are pricey for what you get, I thought, though they were the cheapest Lowes offered. We have had the pair for a little over a year. So far no real problems, though we really do not like the latch door. You have to slam the door to get it to close. To do it over we would probably have shopped a little longer and for the same money got a better deal.

Moved to new house with new Whirlpool appliances, including oven, in August, 2015. I did not cook in oven at all until Thanksgiving meal. Had something spill over in oven. Spillover caught fire. Oven at 350 degrees. Complained to Whirlpool. A supervisor told me that it is normal for spillover to catch fire. They sent out a tech to check oven, and said I would be responsible for paying tech. The tech explained that unlike conventional ovens, this oven has heating elements outside of oven, so to get to the temperature of 350 degrees, the heat at the bottom of oven can get to over 550 degrees. He could not get Whirlpool to replace oven. I didnt have to pay, but now I am afraid to use it. Some of the finish on the inside of the oven was burned away, so it is not like I can trade it in. I feel the oven has a defective design if spillovers are supposed to catch fire while you are cooking, and the finish gets damaged. I will never buy another Whirlpool appliance again, if I can help it.

Whirlpool Range Model XFE381LVS - 12/13/2014 4:30PM Wife was cooking dinner and turned oven on. Smoke started coming out of the back and called me. I ran to the breaker panel and turned off the breaker. Back to the stove, pulled it out and smoke still coming out in back at the top. I could see fire in the top of the back panel. Slowly the fire went out. Unplugged the stove, I removed the back panel, wires were still smoldering and the Control panel was burned thru. Took pictures so I could contact Whirlpool Monday. The Electrical control panel is destroyed as well as many wires. Glad we were home and oven was not left on while we were out in the yard or Home could have been destroyed. Purchased the stove from Lowes 11/02/2010 with a extended warranty. Tried to add receipt but would not accept, wrong type doc.

I purchased a Whirlpool 3-door refrigerator with the freezer on the bottom on 8/17/12. Within 4 days, the ice maker stopped working. It took two days for the repairman to come out and fix it. So all is well with that. Less than 2 weeks later, the refrigerator isnt cooling. Several days later, the repairman came and determined it was the evaporator fan motor and clutch. The parts were back-ordered for 10 days. Parts came in 2 more days before he can come out and install them. He realized they sent the wrong parts. Another week went by, then he came and replaced the fan motor, which is now making an ear-piercing buzzing sound. He came back a week later and said it needed a gasket, which is back-ordered. In the meantime, he put some stick on insulation around the unit. Not much help. Another week went by, and the gasket showed up. It is still making a high-pitched whining sound. He said it was the compressor. Whatever! I hate the refrigerator. The sound is one that just grates on your nerves and you can hear it in all the rooms surrounding the kitchen! A repairman has to deem it unrepairable before they will even consider replacing it. They consider it fixed. What about my bleeding ears! I just want it gone! I am so disappointed. I thought Whirlpool was a good product with a solid reputation. I have a $2300 noise maker! Is there a class action lawsuit?!

I have had many parts replaced on this refrigerator regarding ice maker. But nonetheless yesterday opened freezer and noticed a huge crack about 12 inches on the inside right of the freezer, not near a shelf or anything. I call today of course warranty is up after my 2 yr and Whirlpool says sorry maam there is nothing we can do. Seriously I purchased 2 years and 2 months ago @ $1560 and I’m told I would have to purchase a new one. I will never purchase another Whirlpool anything for we have had nothing but problems with them not standing behind their product. Model #GSS30C6EYY03. This is crazy to me. I have never heard of a refrigerator just cracking through.

We purchased this washer in April two years ago. I have had service people out twice to replace the lid. Tonight, my husband comes into the kitchen with chunks of something that I could not readily identify. He tells me the entire frame holding the light has rusted out and that the light is hanging into the tub! I followed him into our air conditioned interior laundry room and placed my hand under the rim. It’s filled with rust and the light is dangling down into the tub!

My experience w/ Whirlpool has been disastrous. Whatever you do read the reviews on products before purchasing, do your homework first before purchasing any major appliance. Whirlpool company and its employees are a joke. We are paying consumers and spent our hard earned dollars to support a company that could care less about us and our problems with their products they sell to us which are a piece of crap. I purchased a refrigerator made by Whirlpool from hhgregg in Oct 2015, which took 2 months to get it delivered. The refrigerator is not a year old yet, and cannot get anyone to come out to repair it. I have called Whirlpool numerous times, and so have my husband to come and repair a refrigerator that is less than a year old.The ice maker stopped working. Then I came home and discovered that the refrigerator is not cool, and everything in the bottom freezer had almost thawed out, and a repairman was supposed to come on August 31, 2016. It has been hot as Hades, during August, Sept, in the high 90s and they had the nerve to call and say they had to order the icemaker and when it came in someone would be out to fix it. I called the company in Maryland to find out what part did they order because a technician hadnt been out at this point to determine what part needed to be replaced. I called Whirlpool, and yes was put on hold for 45 minutes each time, and when I asked to speak to a manager, I was told that the manager said I could call a repairman and they would reimburse me up to $150.00. I replied That that is not my job. Your job is to send a repairman to fix it.The name of the company that they gave me and the phone number is located in Maryland, I live in the state of Virginia past Richmond, 3 hours away. Then I was told by the company in Maryland that they dont have technicians to Repair Whirlpool Refrigerators. This is totally unacceptable. It is Sept 19, and since August no one from Whirlpool has been out to fix it, neither have they tried to rectify the problem. Bottom Line, DO NOT BUY A WHIRLPOOL PRODUCT, not from hhgregg, Sears, Home Depot, Lowes, anywhere because this is how they treat customers. I have an 88 year old Aunt that lives with us that were responsible for, and she cant even get a glass of ice cold water from a brand new refrigerator thats still under warranty. Whats wrong with this picture?

My experience was terrible. We purchased a side by side refrigerator on June 27, 2011 and it stopped working in December, 2011. We reported this onDecember 19, 2011. A repairman was sent out a few days later, who could not solve the problem because a piece had to be ordered. The piece was ordered and the repairman came to install the part on December 28, 2011.The refrigerator is still not working at all. We have been without ice for this period of time, not to mention the inconvenience of non-refrigeration of food. I pleaded for them to pick up the refrigerator and give me even a partial refund. I was told that three repairs had to be done before they would even consider picking up the refrigerator. I am not a person who complains, but this was ridiculous. I will never purchase another Whirlpool product.

Add us to the list of those whose Whirlpool Cabrio washer has failed. First, it was the infamous circuit board at a cost of $475 installed. Now, the tub bearing is apparently beginning to fail given the machines new propensity to roar like a freight train during the spin cycle. A letter to Whirlpool resulted the too bad ** letter that everyone else has gotten. This really should be a class action suit money-maker for some attorney. So now the question: Throw good money after bad hoping to get an additional couple of years out of it or bite the bullet and buy some reliable brand?Never again a Whirlpool, thats for sure. I pointed out to them that in the age of the internet, they wont go unpunished for this but theyre nothing if not shortsighted. An $800 machine requiring $475 worth of repairs and apparently soon to need another $500 worth of repairs. Whats wrong with this picture?

From day one I was not happy with the new auto fill washer, I was told I just needed to get used to it! Well I have tried every cycle available and no matter what I try cloths don’t come out clean, using the deepwash cycle Sheets on top were still dry once cycle was completed!! Give me back my old washer! Washed much much better.