Whirlpool refrigerator Model #GX5FHDXVY010, freezer on bottom. Ice maker broke within six months of purchase. Made loud noises, would not function to freeze ice. Turned waterline off and now use ice trays like the old days. Shortly thereafter, second unrelated problem started. Drain line started backing up and runs into the bottom of the freezer floor where it freezes into a thin sheet of ice, and then runs onto the kitchen floor. Have had the line cleaned out over and over again. Have been buying fridges for 50 yrs. and have never had this problem. Whirlpool says call a repairman and pay to have it fixed, but it happens over and over again. Whirlpool should come up with a permanent fix and pay to have it fixed. Based on the numerous complaints of this problem, this model needs a recall now.

Our new Whirlpool Side-by-Side Refrigerator is very versatile as it serves the needs of a busy, family kitchen. It is heavily used storing cold foodstuffs to feed our family of four, plus two active grandsons. Being able to re-configure the shelving space enables us to adjust the main compartment accommodating items of different sizes (think a thawing turkey or a 24-can case of soft drinks!) to ensure our most functional usage. The same can be said of its freezer space - it too features built-in slots to reposition shelving for varied size packages and boxes. Convenient in-door water and ice dispensers round out the beneficial features of this attractive appliance.

I have been buying refurbished appliances and this one we bought it brand new. Its a great buy and it will last a while. It does a good job washing and the clothes come clean and almost dry to the touch.

I have owned Craftmaster 30-gallon hot water heater and the only things reliable about it is trouble and aggravation. I purchased this in 2004. I have had to replace the controls, valves, wires, etc. three times in 10 years. And Im now looking at doing it a fourth time. The design of these parts are utter crap! Cheap plastic! After replacing these parts, this hot water heater works great for a few years, then invariably starts acting up. The pilot light goes out when the heater is supposed to kick on instead. Getting the pilot light lit again, is an exercise in futility! The red reset button once released, immediately extinguishes the ignition flame. Supposedly, after holding it down for 1-2 minutes allowing gas to build up, it should light the coils... and if it doesnt, youre supposed to wait 10 minutes to try relighting again. You can repeat this process for 12 hours, and if you finally do get this temperamental piece of junk to light, youre lucky. Customer Service has been useless in assistance. All they want to do is send you e-mail, and get you off the phone. Not to mention, Ive been told by many a rep that the hot water heater extinguishes itself, if water is overheated, and that it must be my fault for setting the temp too hot. Baloney... Ive been told that the underside vent must be cleaned every few months, so that air flow is accurate. Makes no difference one way or the other. And recently, Ive been told by a rep, that my 40-yr-old house likely doesnt vent exhaust out through the roof properly. This product is inferior and unpredictable. Its great when it works, and the pilot light stays lit. God forbid it ever goes out though! It is next to impossible to relight. I have spent more money on service technicians attempting to repair/replace parts, than it would have cost to simply by a new hot water heater. I miss the old days, when it was easy to light a hot water heater: Strike a match, turn the gas on, and instant hot water. No muss, no fuss. Having owned many properties w/ hot water heaters over the years, I have never encountered such repeat problems, as with this product. Its simply not reliable, and not worth the $$$. Never again, will I buy a Craftmaster Product. And I had no clue that there was a Class Action Suit filed, and a settlement involved in these faulty units. Whirlpool/Craftmaster should have notified everyone, who purchased one of their units. Now Im stuck w/ a constantly broken unit, and zero recourse. I will never buy anything Whirlpool/Craftmaster again, as a result.

Water heater was defective from the factory with a pinched wire between the thermostats. After replacing everything on the heater Whirlpool would not reimburse any parts or labor for the unit... Whirlpool is dead to me now, and forever and I love to tell my story to prospective buyers of their products!!! So far, to date I have cost them about 14 sales of major appliances (and still counting!!!). After reading some reviews… Im (sorry, I omitted the personal insults) in respect of your review guidelines.

I purchased a new high-efficiency front load Duet HT Whirlpool washing machine (WFW9200SQ02) in January of 2008 for nearly $1000. I dealt with the mold issues and permeating smell for all these years, but the machine failed catastrophically this month - after just over 3 years - on a $1000 machine! The rear bearing went out. The parts alone are nearly $500 and the labor is estimated to take 3-4 hours by a trained technician. We are talking about an $800 repair --more than a new machine would cost. The most disconcerting part is to see how often this is happening. It is commonplace. The bearings go out on these things, sometimes after only a year or two, sometimes after 3 or 4; but it is very rare to have any machine go longer than 6-7 years. Whirlpool wont do anything. The best chance is forcing a recall related to the class action lawsuits pending about the mold issues, but by that time, how many people will still have their machines?

Purchased a new Twin Thin washer & dryer combo when I first moved into my new apartment two-years ago since it was a good fit for the space that lies inside my patio. Nothing BUT problems from day one since it DESTROYS/EATS your delicate clothing. Repairmen in and out could find nothing wrong with it. The problem lies in the fact that the so-called gentle cycle agitates at the same rate as the other cycles, but stops so that the agitation time is shorter, but at the same time the agitation no matter if its shorter is still too vigorous for delicates. Under contract, so keep having repairmen come at no cost to me other than a complete waste of money purchase inclusive of unwearable brand new RUINED clothing.Called the company the other day & was told they could SELL me a different one, but they would probably not pay to have the LEMON removed. Also, suggested I wash my delicates in a mesh bag which is impossible to do when one has maxi dresses that tell you to wash on the delicate cycle. Mesh bags are made for small items - DUH!Repairman came again today, and was kind enough to make call to them. Later found that their response to him was that I was putting too much into the washer. Like no way, Jose! Asked tech to forward e-mail to them advising that they were more than welcome to come film me when I wash because that was NOT the problem with it. Already knew Whirlpool had discontinued this washer/dryer combo, but THAT fact was never mentioned. A lot of sites online no longer even carry the parts for it. Found others with the same issues on various sites relating to this now discontinued model which is akin to a Purana fish with shark fins. E-mail sent to tech that was here today asking him to forward my e-mail to whomever he made contact with today via phone that unless the situation is remedied that I would have to take further action. Now awaiting response from the main man tech or whatever his position is at Whirlpool.Bottom line is that it is a LEMON that has not only cost me money, but excessive amount of time to resolve this issue not to mention time spent online researching this, that and the other concerning this discontinued appliance. Warning to all out there - DO NOT BUY WHIRLPOOL - UNLESS YOU WANT A HASSLE and a lot of BS. Found they already have an extreme number of lawsuits against them during my online searches. So, ball is in their court at the present time. Will be calling them the end of the week once again in order to get this problem resolved unless I hear from them via e-mail.Totally exhausted from it all. Word to the wise: DO NOT waste your money on Whirlpool appliances unless you want more problems than you already have. I have health problems which are exacerbated by stress, and believe me this has been one of the most stressful and one of the longest things to resolve (two years) brought on by their lack of admittance that this DISCONTINUED product is a real LEMON. BUYER BEWARE OF WHIRLPOOL - I rest my case.Updated on 07/12/2018: Cant seem to find this model anywhere now. Not to mention the fact that I found it not only eats my delicate clothing, but is also ruining my towels, etc. and I use the regular wash cycle for these items. You cant find my model #WET4024EWO anywhere; looked like they put a similar one out with a slightly different model # in which the drum/agitator differs from mine. Now find Im having difficulty finding that NEW stackable model on the WEB. Leaves me wondering if that one has also now been discontinued???They have given me no resolution to my problem as of yet, and Im totally EXHAUSTED from it all. Have high blood pressure, a heart condition, and cant even sleep right anymore due to their lack of cooperation to solve this on-going problem which is certainly not helping any of my medical conditions either. Its causing nothing but STRESS, STRESS, STRESS and more STRESS! Will be filing a complaint with The Better Business Bureau by next week if not resolved by this weekend (if I live that long).Updated on 07/17/2018: In looking at this Washer/Dryer Combo Model # WET4024EW aka LEMON again today after noticing more clothes which now have holes in them after being washed on the gentle cycle with the highest water level possible, I noted the size of the agitator. Bottom line on this is that the agitator also appears TOO LARGE for the machine which also could also be another contributory factor to the destruction capabilities of this now discontinued model. Also, inspected towels today and found torn stitching & thread tearing in those also; appears EVERYTHING you wash in this machine gets destroyed. In researching further on their newer makes noticed that the agitator appears either much smaller or has been removed altogether. Hopefully this will serve to aid anyone out there who is thinking of buying this machine second hand from anyone out there that is attempting to sell it vs obtaining restitution from Whirlpool.

I bought my washer duet (model WFW94HEXL2) in Sept. 2011. Today is Jan. 2013 and it has been a year and four months since I got the washer. I decided not to buy an extended warranty. Its only my husband and I at the house so we take really good care of our appliances. The washer stopped working and is giving me a code F-6/E3/E1. Basically, I need to change the central control unit ($350), door latch ($120) and labor ($180), for a total of $656.13. Really? I paid $1,105.00 for the washer. Im really upset. I called Whirlpool and they said the item is out the warranty and there is nothing they can do. I am really upset.

Bought a Whirlpool French Door, Bottom freezer mount appliance from Lowes in Jan 2014. Model WRF990SLAM00. Jan 2015 the freezer part stopped working. Whirlpool approved repairman came and knew exactly the problem because he was aware of this being a consistent issue with Whirlpools. He contacted Whirlpool and they quickly agreed to send repair kit for FREE. Took 2 wks for parts to arrive, and neglected to send along required tool/gauges for repair to occur. I called Whirlpool C.S. and they claimed they knew nothing and said our fridge was on no problem list. I had repairman call Whirlpool and they claimed appropriate tool/gauges are no longer available! This fridge is only 1 year old!!! Now we are completely ignored. Whirlpool will not even talk to us about help of any kind. HORRIBLE customer service!!! Crappy appliance! After thinking our Whirlpool appliances were a good investment, I will NEVER EVER BUY WHIRLPOOL AGAIN!!!

My complaint is basically the same as all the others. Clothes do not come clean in my brand new Whirlpool washer. Ive had two other Whirlpools, and they were fine. This one, however, is a piece of junk. One of the main problems is that the washer is designed to use only lukewarm water, even on the hot setting, it does not use hot water. Another problem is too little water. Another irritating factor is the constant locking of the lid. Another problem is the constant starting and stopping of the agitator. This cannot be good for the motor. Im at the point of giving away my new washer which Ive had for exactly one week. This is a totally inferior product, and I feel that I have been really ripped off.

GX5FHTXVB00 - Purchased fridge in 2009. In the second year the freezer got too cold and fridge was warm. Coils were frozen. Lost all food. Repairman replaced thermostat. This happened twice more with the same result. My warranty has expired, fridge is 5 years old and its happened for the 4th time. Whirlpool doesnt care since its out of warranty. NEVER will I purchase a Whirlpool appliance. They DO NOT stand behind their product!

We purchased our Whirlpool Duet model WFW9150WW01 13 months ago. The warranty was up at the one year mark. We chose not to purchase the extended service plan. After all, a washer should last at least five years right? Wrong! The front seal has gone bad. It is an $85 part plus shipping, plus hours of my time. So, I purchased a product that is supposed to conserve water and instead I am having to purchase a petroleum-based product (the rubber seal), as it would seem, every year or so! These companies have us snowed with the whole conservation bull! CFLs, High Effeciency, Bio Fuels, etc., its all a hoax! And it is a hoax at our expense. Does anyone just produce a good product anymore? Oh yeah, I forgot... Japan does! Our economy continues to go to hell while other countries are coming online. Get your act together, guys, before we lose everything!

Whirlpool® Gold® 5.8CuFt Capacity | GAS Stainless - This was not an inexpensive stove. The self cleaning oven function is a total failure. You are not supposed to use oven cleaner on the glass, it now has obscured the view into the oven. The top of the stove is very difficult or impossible to clean. The knobs are a dangerous issue. They will fall off at the slightest touch and the stainless markers around the knob are just a stick on label. The oven temperature is not accurate. The bottom drawer is completely rust spots on the inside. What more can I say. Oh I know. Whirlpool your quality is a disgrace and I want a refund.

A top loading washing machine with an agitator in my opinion, gets my clothes 100xs cleaner than one without. Ive owned front loaders and top without agitators. Never again. Top with agitator is my personal preference from now on. Also Whirlpool has never failed me unlike other brands.

Had washer less than 1 year and washer stopped and was flashing code F 51. Called Whirlpool and they sent a repair person. He worked on it and didnt fix problem. Called Whirlpool back. They had to order parts. Repairman came back - replaced parts. Now not 6 months later same thing happening. Whirlpool said we have to pay for labor to repair again. We went online after this happened the first time and saw where others had same problem - this washer should be recalled. The repairman said this part was corroding. This should not be happening on a new washer. We will never buy another Whirlpool product again!!!! Im concerned that it will keep repeating over and over and we paid 700+ for this washer not 1 1/2 ago. My last washer lasted 15 years!!! Wasnt a Whirlpool!!!

I have had almost all the same issues everyone else who reviews the Cabrio WTW7800XWO washer. Now, the spring loaded lid wont stay up, so we have to use the Downy bottle to load the clothes. Thankfully, I have not had the lid crack... yet. We have had it serviced once while under warranty, that tech told us it wasnt good to wash small items, like socks. Are you kidding me? Now, the heavy lid falls on you while you are loading. I also have the Cabrio dryer, and we have fixed that more than the washer. DO NOT BUY A WHIRLPOOL CABRIO. We bought it because it was the largest unit in the store, but it is junk.

Model # WFG510S0AS1 SER #R30850040. Oven was installed NEW in the home I purchased in July of 2013. I used the cleaning feature on it in Nov 2014. I am amazed that it did not start a fire. Please see pictures attached. The whole control panel melted. This makes the oven unusable and extremely dangerous. I will need to replace the whole control panel. I followed the instructions completely in the manual provided for the cleaning cycle. It says in the manual to only clean the over this way as using easy off or any other cleaner will damage the inner surfaces.Whirlpool claims they have no knowledge of this problem but there are numerous complaints on their site about it as well as other internet sites complaining about the melting of the control panel. I need to know how to fix this problem and dont believe I should have to pay for something that is obviously a flaw in the materials used. It is extremely dangerous. Since these pieces of Whirlpool equipment were installed by the broker that originally purchased the home, I have no record of purchase. I can try and contact him and see if he has anything but kind of doubt he has receipts now.

I love a refrigerator that keeps my milk and water ice cold and keeps my fruits and veggies crispy and fresh without freezing them.

I bought a house with Whirlpool appliances and I bought the extended warranty for all the appliances, I started to have issues with the refrigerator almost 4 months ago and still waiting for results, do not buy whirlpool products, every time you call the warranty department be prepared to spend at least one hour waiting for a customer representative. Buy LG or GE instead. These are excellent brands that I have owned in the past.

The drip hose had to be replaced 6 months after I purchased the refrigerator. At that time the warranty covered the part but the technician told me that Whirlpool was aware of the problem. About 5 months after the warranty expired, the same problem again - ice built up on bottom of freezer and water leaking out from the left side leaving a puddle on the floor. I called Whirlpool and they said warranty is expired. I tried to tell them about the defective part but to no avail. Had to pay to have drip hose replaced again. One year after that the main CPU board went and had to be replaced ($350.00). I sent the part back to Whirlpool, registered mail, hoping they would respond with a yes, this was defective. Their response back to me was, “warranty is over.” For a main board to fail in a $1500.00 refrigerator in less than 3 years was uncalled for. Two days ago I noticed the puddle on the floor and had to call in a technician and ONCE again the drip hose had to be replaced ($160.0). He told me Whirlpool is well aware of the problem and there is a Service Pointer out on it and the code is S38211. Thanks for nothing Whirlpool. The refrigerator was a lemon and you did nothing about it. I wish I would have read these reviews first. No more Whirlpool products for me! PS. I was a dedicated fan of Whirlpool for 40 years!

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

Bought appliance (Whirlpool French Door Refrigerator Freezer) in 2014. The seal that closes all the brackets with screws and you had to hand guide it to close. Then the freezer got out of alignment and wouldnt close and seal. Ice built up behind drawer which prohibited the opening of freezer drawer. Wouldnt open more than 5 inches on one side and 3 inches on the other. Had service tech out. Cost almost $200. Did not get French doors repaired because the part cost over $125. Less than a year later I have to have a repairman back out for same problem with the freezer door and ice build up. Not happy.

Stove was purchased in June, 2021. Two months later, oven will not heat up!!! Contacts Whirlpool, and TEN days later, a service person finally shows up. Problem appears to be a circuit board that they dont have, and has to be ordered! When will it arrive? He has no idea!!! I called Whirlpool, but its frustrating and a waste of time. You only get to talk to someone that appears to be reading from a script! If were lucky, well be without an oven for one month; however, it could be two...or three...or four!!! My advice: Dont buy this stove/range!!! Not only is the oven an issue, but it just seems flimsy and subpar quality, especially the oven door. Added to that, the glass top is very difficult to keep clean... Worse than any glass top stove weve had in the past.

Weeks ago, we received a new refrigerator from Whirlpool. Never really got down to temp. They replaced the compressor and still does not work. You would think a company like Whirlpool would replace it. That is a joke. They want to try and repair it again, another compressor? Now I have thrown out the food in it and feel like Whirlpool could care less. DO YOURSELF A FAVOR< DONT BUY ANYTHING MADE BY THIS COMPANY OR THEIR OFFSHOOTS.

We purchased a brand new Whirlpool water heater from Lowe’s two years ago. The water heater is not heating properly, and I contacted customer service to inquire about their great warranty. I was very disappointed with their poor customer service, but above all, their warranty. They emailed instructions to run a test, which did not resolve my issue since I still run out of hot water halfway through my shower. Mind you, its only one person in the house for a 40-gallon Whirlpool water heater. I have replaced the heating elements and thermostat, and it is still not heating. I contacted Whirlpool customer service, and they are refusing to replace it, stating that the water heater is working. I will never buy any Whirlpool appliances again. They do not back up their products, and their customer service is worthless. My recommendation is not to buy Whirlpool products.

Whirlpool Energy Smart Residential Electric Water Heater - On top of this water heater is a junction box. If it goes out, so does the water heater. I am on my fourth junction box, at my expense on three of them plus the electricians bill times two. They finally sent me one free!

I have automatic Whirlpool washing machine since 3 1/2 years I am using. Now 2 times electronic board came problem so how many times can change like this? Why they are manufacturing if they cannot solve this problems? Should not sell in the market. This all not coming free and need to struggle. Whirlpool products all very bad appliances.

I have owned a Whirlpool Gold Series Refrigerator for one year and 9 months. During that time I have had 7 repair issues. Each of the past ones took at least two weeks to repair. This past repair has to be redone because the new parts are also bad. The part is now on factory backorder. It will be at least two months for this to be repaired. Whirlpool says its too bad, we just have to deal with being without a working refrigerator for months. Do not buy this product!!! The warranty only means that you are forced to wait months for repairs. They will not replace, refund, or even extend the warranty for all this downtime. You have no recourse with the company.

The shelves in the newer units are plastic not glass with metal and they rip/break holding heavy contains like gallons of milk, and they are more expensive to replace. I just wish they would go back to building things like in the old days. My last refrigerator lasted 20 years. Ive had this one a year paid twice the price and already had to replace shelves and trays for it..

I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????

I purchased for over a thousand dollars a whirlpool propane hot water tank. Three months later the safety heat thing that turns it off is defective yet I have to pay for shipping on this. Then again every three months. Its been a year and a half and the damn thing just blew up and almost took my house with it. I paid for a product that works not one that needs replaced yearly. But do they care? Nope. 2 weeks before someone can even look at it. I plan on reviewing until whirlpool isnt purchased by anyone again. This is a brand that was supposed to be quality, instead its just a scam!

My Whirlpool refrigerator needed a $400 mechanical repair shortly after the 1 year warranty expired. Its only been 13 months since repair, and the refrigerator is experiencing the same problems again! Whirlpool is plagued by negative reviews across the internet... hundreds of complaints on Yelp.ca forums, and consumeraffairs.com. There also used to be hundreds of negative Google reviews, but mysteriously all of those reviews have disappeared, and you can no longer leave a Google review for Whirlpool Corporation.

We purchased a new motor home with a whirlpool refrigerator. The refrigerator went out three months after purchasing this new motor home. We have had two expertise come out and check. Both repairmen said there was a leak in the cabinet and needed to be replaced. They called Whirlpool who will not honor the warranty. We are still under warranty but it is not worth the paper it is written on. Do not buy their products because their products do not work and they will not replace broken items from the manufacture. Will have to contact better business. Not material enough to hire attorney. This is what they count on. BEWARE.

First of all, Whirlpool is fully aware of the problems with water heaters and intentionally places requirements on the consumer until they give up. This info from a distributor. I bought 30 gal. gas water heater 7 months ago. Six days ago the pilot light went out. Went to Lowes (purchased there) and bought a replacement. Wrong one. Returned to store and was told they dont stock repair parts, call factory. Monday called warranty number. They offers to send thermopile, it would arrive in 5 days. I paid $30 for overnight. Plumber installed new part. Still doesnt work. Whirlpool says have the plumber call them theyll walk him through troubleshooting. I ask, Whos paying the plumber? They reply, You are. Plumber calls Whirlpool. They tell him to clean the screen. He does. They tell him to disassemble the burner. I stop plumber. I ask Whirlpool, What if its not the burner? They reply, Then well troubleshoot something else. Meanwhile Im 5 days without hot water. I go to Lowes where heater was purchased. The manager thought it funny Im another victim. I ask, Why doesnt Lowes stock heater parts? He says because Whirlpool doesnt let them carry parts. Im beat. I surrender. Parts from Whirlpool would take another 5 days and theres no assurance itll work. Lowes refuses to assist.I go to Sutherlands and buy a $450 Rheem on recommendation from plumber. Manager from Sutherlands hears my sad story and writes on receipt: Any warranty failure and Sutherlands will replace water heater free. He signs his name on receipt. I pay plumber to swap out heaters. Anybody want a 7 month old Whirlpool water heater. Like new. Cheap! By the way... I originally went to a major appliance parts store asking for a thermocouple for a Whirlpool. The three guys at the counter started laughing Hey we got another one looking for Whirlpool parts. They didnt have them either. Lesson learned.

I purchased a Whirlpool oven 14 months ago. I just paid it off 2 months ago. The oven stopped heating. I talked to Whirlpool... and basically because I did not purchase the extented warranty I am SOL. I will never buy a product from them again. Complete junk.

I purchased the Whirlpool washer with the expectation of having at least clean clothes. In fairness, I do wash some pet items but they are done separately. My clothes at time come out dry in spots because theyve not been touched with water. Forget the balancing issue. What I will have to do is wash, rinse, and repeat. This will be my life until I can get a new washer. Never again Whirlpool.

Whirlpool model WRF560SMYB04 - We purchased this model Whirlpool in Dec 2015 after having a refrigerator for 18 years with no problems. We started having cooling issues in late 2017 and finally an intolerable fan noise in April 2018. Researched it and purchased a fan. Opened up the freezer panel and found that the unit was completely frosted up to the point where ice had formed around the freezer fan and was hitting the blades. Contacted a repairman who came out and called in the issue to the Whirlpool tech line. He was told that he should check continuity on a couple of wires. If these checked out, the problem was the user interface board at the top of the refrigerator. We purchased a new board for about $100 and installed same. No change. I was now $250 into repairs and no further. We became aware of Whirlpool Service Pointer W10875533A which described conditions that we were experiencing. The issue was a coil thermistor that would corrode (apparently within 2 years) and would not provide accurate signals. Whirlpool also issued an instruction sheet W10902213 Rev A describing how to relocate the thermistor and protect it with foil and tape. My repairman came out, confirmed the thermistor ($54) was bad, replaced same following the Instruction Sheet. We were now out over $300 on a $1000 refrigerator purchased 2 years earlier.Whirlpool issued the Service Pointer (not to consumers, but to repair shops) in Sept 2016 (within our warranty period). We received no notifications from Whirlpool of the defective design. Nor did we receive a recall notice. Moreover, Whirlpool tech group must have known about this issue, but instructed my repairman to replace the interface board. Whirlpool knows they have a defective product out there but are doing nothing to inform the consumer or stepping up to correct the problem. We have contacted Whirlpool to recover our expenses...will let you all know how that goes. Anybody interested in pursuing a class action?

I purchased this washing machine December 16, 2011. I paid $737.07 for this machine. 14 months later I had to repair the top of it which cost me $255 for the lid which the plastic around the lid was cracked. I had to pay $136 installation fee and two years later the exact same thing happened again, the plastic cracked. I have contacted Whirlpool which took a complaint - said that was all they could do. Ive contacted the store where I purchased it, they can do nothing. I read online there are many complaints about the lid on this washing machine. It shouldve been a recall. I will never purchase a Whirlpool product again. I will not pay to have it repaired again. I will give it away and purchase something else not whirlpool and not from Lowes. I expected some kind of compensation from whirlpool on this. I have all my receipts.

I purchased a Whirlpool washer in 2010. It has started to rust. I called the customer services dept. They told me that there was nothing they could do about it because it was over a year old. I asked to be transferred to a supervisor. She told me the same thing. I told her that its not as if Im looking for a new washer. She said that there was nothing they could do; I had to pay for the repairs myself. I told her, After spending almost $1,000 on a washer, I have to pay for the repairs? She said, Yes, maam. I asked if I could speak to someone over her. She said that she had to take down my name and number and someone would call me back in 24 hrs ... from the management team.She asked for my number and not my name and said someone would be calling back. I told her, How are you going to forward the message without a name? Maam, Im sorry. Whats your name? I doubt if anyone will be calling me back. Whirlpool customer service sucks! They dont know how to treat their customers. Watch out for the warranty. What they call a warranty is not.

I bought a Whirlpool Cabrio 2 years ago and until last week it was fine. We got an error message that said we had to call for service so we called a local whirlpool repairman. The repair guy told us it was the control panel and it was going to cost between $400 to $500. He also said that he works on a lot of whirlpool washers and this is the first time he saw a machines control panel fail. He recommended that we call Whirlpool.I called Whirlpool customer service and after waiting on the phone for 40 minutes I was quickly transferred to customer resolution and was told that since I hadnt purchased the extended warranty there was nothing that they could do for me. I kept asking her, There is nothing that you can do to help me? And the consistent answer was no. I will never buy another Whirlpool appliance. This has been so frustrating to have an appliance that looks brand new and wont work. The manufacturer wont even try to help with fixing the problem. Amazing AWFUL CUSTOMER SERVICE.

My two-year old Whirlpool Duet Front Load washing machine is ripping my familys clothes. When I went online and saw all the other customers with the same issue, I contacted Whirlpool. Although the contact said that he knew I was frustrated, he could do nothing but send a repairman at a cost of $129 for me and then I would also have to pay for parts. I informed him that the online sites are saying that this is just a temporary fix. He pleaded ignorance and could offer me no other alternative. This is the last Whirlpool or Maytag product we will ever buy... and letting others know about the lack of cooperation.

I bought my Cabrio washer about 3.5 years ago. Little after the year, I had to replace the lid because the hinge broke. Then came the F1 code, which I noticed if you turn the machine off for a couple of minutes, it resets itself. About a week ago, it started making a grinding noise and staining the clothes with oil or grease. Transmission problems. I was told by the seller it had a 10 year warranty. I called them up and now I got to foot the bill for a technician to come to my house and tell me what I already know plus labor. Might as well buy a new one. Beware because I believe Kenmore is manufactured by the same company.

I bought a Cabrio 2 yrs. ago and I wish I had my old washer back. I read reviews and checked out a lot of literature and thought I was getting a quality machine. What a waste of hard earned money. I cant get clothes clean, its loud, and it leaves soap residue even after an extra rinse. Whirlpool products arent what they claim to be. I had a freezer I bought because I bought a half a steer and it quit running and I lost all my beef - $700.00 worth. From now on I will stay away from any Whirlpool products!!

I’m getting the run around with service. No one comes to our area to check our new Whirlpool hot water heater. The hot water heater has not worked right since I installed it. I need a service tech to come to my house at Whirlpool’s expense and check the damn thing and get me taken care of. Does Whirlpool want to retain a customer or not? Its that simple. My cell phone number is **.

We purchased our oven on 12/06/15. I have called and complained about the AquaLift oven on more than one occasion. This technology does not work. I would have thought that there would have FINALLY been a recall on this oven. I am a senior who thought this stove would last me for the rest of my life. I have to stand on my head to try to clean it. NEVER, NEVER, NEVER would I have purchased this if I had read any of the reviews. Buyer beware!!!

Ordered this two days after my son came home from college. He had to be out of his apartment July 31 2016 and brought 4 years worth of laundry with him. Monday my machine breaks, Tuesday I order this thing from Lowes Arrives at 2:30 on Thursday and as it is being installed I ask why the water fill is so slow. It is trickling out like a childs toy. Delivery man tells me the water is completely turned on. He hears this remark a lot from people who buy this model. I put in my first load of laundry, a small load of about 6 things that I am washing for my mother who is in a nursing home. They have that nursing home smell. I push pause as the machine is cleaning to unlock the lid and peek inside. Oh my God the clothes are sitting on top of each other not even covered in water. I then shut the lid and listen to the tiny slush of the machine agitating. At the end of the cycle they smell exactly the same. Dirty.I had read to use the deep fill so I rewash them on deep fill. Look inside halfway through and what do I see? Wet clothes piled on top of each other, still not floating in water. How are these clothes getting clean when they are in a wet pile on the bottom of the machine? I take them out. Still not clean. Not smelling quite as bad, but not smelling like soap. I then washed sheets, a blanket, and some clothing of my sons. Nothing smelled particularly dirty but NOTHING smelled like soap. The quilt was covered in hairs (my son and roommates had a dog) and soap residue. I had read this in reviews online also. I am wasting time since each load takes from 50 to 130 minutes (yes). I am wasting soap, oh but I am saving water - not really.Well Lowes has a 30 day return policy so I went down there and am expecting a GE machine with an agitator tomorrow, Saturday! Cant wait. The only one saving money are these manufacturers They no longer are spending cash on producing the agitator out of plastic, attaching it with nuts and bolts, or using gaskets between the parts. DO NOT BUY THIS PIECE OF JUNK, do not even look at it. I question all the HE machines at this point. You need to use HE soap cause you cant wash away suds in a machine with no water. What a con - the whole thing is.

I purchased a new Whirlpool 3.6-cu ft Top-Load Washer (White-On-White) Model #: WTW4800BQ from Lowes on 11/1/14, which was only 3 ½ years ago. The washer began making noise during the spin cycle so we called for service. The technician claimed that the bearing pack needed to be replaced and the repair would cost $400. This amount is $20 higher than the amount I paid to purchase the washer. Because the warranty is only one year, I contacted Whirlpool today and spoke with a representative. The representative said they could repair it under the warranty. When I asked how to proceed, she then asked me if I had an extended warranty. When I replied that if I had an extended warranty, I would be using it. She declined any assistance. I now have to purchase a new washer after only 3 and ½ years. I own 10 rentals. I promise that none of them will ever include a Whirpool product again.

I had this same refrigerator in another home and had no issues, this particular one now I have nothing but issues with it. It seems that the quality is not consistent. First the ice maker was not working, then the freezer light burned out and now there is extensive frost build up in the freezer. The refrigerator is only 2 years old!

We purchased the Whirlpool refrigerator on July 9, 2012. Refrigerator was replaced on August 23, 2012. Since then there have been many, many service calls. I wish I had kept records to be able to tell you exactly how many times, but we purchased an extended warranty. From memory, I can tell you the ice maker has been replaced twice, new doors have been installed for refrigerator and freezer (replacing ice maker a third time), then within the last three months the freezer door was again replaced (replacing ice maker a fourth time). The gasket on the freezer door has been replaced. At one point the refrigerator was colder and freezing and the freezer was not freezing. Parts and pieces have been repaired on several occasions. The inside of the freezer door next to the ice maker is still frosting up and yet again the ice maker is not functioning and needs to be replaced a fifth time. In other words this Whirlpool refrigerator has been a lemon for us. Finally, we figured it out. There is a fairly large gap at the top of the freezer door between the case and the gasket. If you run your hand across the area where the gap is, there is definitely a dip in the face of the refrigerator case where you can see the top of the ice maker. A picture showing the gap is attached. I am not sure that our purchasing a store extended warranty was fortunate or not. My husband has insisted on repairing this thing over and over and over because of the extended warranty. I think repairing it is futile and the only people being punished by all the repair calls is us because we frequently do not have ice, we are losing food because of freezing or not freezing or cooling or not cooling as the case may be. Thank God, the warranty expires in July and we can repair this Whirlpool by replacing it with another brand -- not in any way associated with Whirlpool. If you Google Whirlpool, you will find that Whirlpool is affiliated with almost every other brand of refrigerator and really limits your choices. Based on my experience with this Whirlpool refrigerator, I will never purchase another Whirlpool or any other brand associated with the Whirlpool brand. The myriad of repair persons in my home probably find a Whirlpool refrigerator is job security for them.

We have had the washer and dryer for over 10 years and they are still working great. We have had washers and dryers in the past within 2 years have failed, and repairs have cost us almost as much as a new one. Thank God for the ones we have now.

It works great, it looks great. I been having for many years, and never gave me any problems. I do love nice microwaves and Whirlpool is a great. I would recommend it to anyone that is interested.

I love this stove! It is nearly perfect. I wish it was easier to clean the glasstop, but I imagine that comes with any glasstop stove. The stove is easy to use, and I love the cooktime option. My only complaint is that the timer is very quiet, and when it is a timer while something is cooking, it only beeps once. If its a timer when nothing is cooking then it will go off repeatedly until you turn off the timer.

I purchased a stainless steel side by side refrigerator and unbelievably the doorshelves came crashing down - they just cracked in the middle. How cheap can stuff be made, those fridges are not cheap. I thought Whirlpool was a good product - I guess not.

We purchased it from Best Buy. It was a good thing we got the extended warranty. They completely rebuilt it two times. In the 6 years we have had the washer. The motherboard went out. The bearings went out. The only thing nice I can say is that it’s a top loader and doesn’t get smelly like the front loaders do.

Piece of junk that tears up clothes but doesnt clean. Company has ZERO care for their customers. I will never buy Whirlpool again. We called and called and called. Washer took two hours for a normal load. Crust and odors still there. Dryer was fine.

I bought a refrigerator from Lowe’s and the refrigerator had a lot of manufacturing defects. I called Whirlpool and 3 techs were sent to my house. After the last tech, Whirlpool decided to exchange the refrigerator. Since then, Whirlpool has been playing games with me.

Whirlpool gas range convection oven - I have only had this range for 2 weeks. Manual is sketchy to say the least. Purchased from LOWES - salesman were not well-informed. I have had to do a chat to find out information. Range looks great but performs poorly. Takes a while to heat anything even on high and on large burners. Grates are too heavy. I am sorry I did not see the editor review before I purchased. I have not used the convection so I cannot speak to this but my choices were limited when I purchased and I did not want a convection oven and other ranges would not purposeful for my use.

Everything comes out clean and it doesn’t cause items to be tangled around each other. It has a setting for every possible type of load. I especially like the option of having “deep water”. Not having a “glass” lid is a plus.

I purchased a 40 gallon water heater at Lowes and installed about 3 years ago. A couple of weeks ago, it got an upper sensor failure code on the gas valve. It would heat by resetting (turning valve off, waiting a minute and then lighting) but after a few minutes, it would fail again. I called the customer service and they mailed out a new upper sensor. When it came a few days later (I paid for shipping), I installed it but the same failure code. Again, the only heat I could get was by resetting the valve several times before a shower. I called customer service again, told them what I did and they said, Oh, the problem is the gas valve then. So they mailed out a new gas valve unit. It then came a few days later and I installed it according to the enclosed directions to the letter. Still got the failure code and still had to keep resetting it to get any warm water before a shower.I called customer service again, told them what I did and he said, Well, did you flush the water heater with apple cider vinegar before you installed the new gas valve? I said, No, it wasnt in the enclosed directions to do so. He said, You should have done that and it would have worked. I will send out a new gas valve. At this point, I blew up. Two weeks with no reliable hot water. I told him I want a new water heater and he refused. I asked to speak to his superior. He said no. Dont ever get a Whirlpool product. Some other crappy company builds these turds.

Oven was just about 3 years old when the oven bake feature failed the first of many times! Display says fault detected. Was able to get oven cleaning done and then it worked again but eventually has failed repeatedly since. Further reading and support from technicians has revealed its an oven control issue and replacement part is same cost as new oven! Apparently the oven control Whirlpool designed and installed cant handle heat!?? Very unreliable and would never buy their appliances again!

Purchased a WDF530PLYM3 Whirlpool dishwasher at Lowes in 2013. Now Ive paid $96.00 to Whirlpools authorized repairman to tell me it needs over $400.00 worth of parts (user interface and control board). He informed me with new digital controls, you MUST purchase extended warranty because they are not built to last and repairs are ridiculously expensive.

I paid over $1,000.00 for a washer based upon previous experience with Whirlpool appliances. I am single, over 65, and use this machine infrequently, as compared to when I had children. The only thing Whirlpool is offering is another of their machines at a discounted price. I value principles more than dollars. I refuse to give them another $600+ as a reward for making junk which apparently should have been recalled. The part I need is not available any place Ive found online. And it completely controls the power to the machine. You cannot open the door, you cannot turn it on. I had two service calls to discover this part is not available.

After replacing our competent GE dishwasher with a Samsung dishwasher and having to replace it immediately due to the terrible job it did, we bought a Whirlpool Gold Series (stainless tub) for just under $400. I realize this is the bottom of the stainless tub price point, but we have been so disappointed! The silverware container sites outside the regular tub, and rarely cleans even easy substances to remove, if there are more than a few items in each container. Dishes on the other levels are very hit or miss -- each and every load has to be examined for dirty dishes. Id pull this one out and return it too if it werent such a hassle. Dont buy this product.

Both the washer and dryer make terrible screeching noise. The dryer only dries on time drying. The store I bought them from have been here over 7 times too fix them. They still are not fixed. Just a terrible experience with this set from day one, load one.

We bought the Whirlpool Cabrio forcibly when our 20-year-old top load whirlpool finally gave out. The Cabrio sucks. It does not get anything clean, it ruins clothes due to low water which creates friction, clothes are left wrinkly, smelly, pilled with lint, stinky and unclean. Ive had it for a year and Ive given every cycle a chance. It simply does not do what it is supposed to.The HE washers are supposed to reduce water, but having to rewash everything several times with load times up to two hours not only increases the amount of water used but increases the amount of energy used. Our electric bill has gone up $30-55 a month on average. This doesnt even account for the fact that Im spending nearly 16 hours a week doing laundry for a household of five. Thats nearly triple the time I used to spend on laundry. From having to pretreat even the most minor stains to spending hours trying to get the wrinkles out, and having to remove pills of lint, to the fact that one wash cycle does not get the odors out nor the dirt out therefore multiple cycles are required. I honestly think I might spend less time if I hand wash everything, I certainly would get them clean and deodorized. UNFORTUNATELY Government regulations force the consumers to buy HE washers so our choices for clean deodorized clothes are non existent. If I had to do it again I would buy a used non-HE washer knowing it would run another 10 years and actually get my clothes clean.

Whirlpool Dishwasher Quiet Partner III Model #8575637, White - Purchased in 2006. As of July 2013, I can say this is the worst dishwasher we have ever owned. After normal use (once a day or less), the plastic on the front control panel began cracking in the first year, and the button covers have fallen off completely. Dishes were never completely clean (at least not as clean as other dishwashers). Dishwasher leaked out one side and needed repairs. Now it is in need of a new valve, because no water is coming into the inner cavity. Repairman says it is likely that the control board, which is getting moisture into it after losing buttons, etc., will probably need to be replaced soon as well. $300 more to spend on a repair bill. SAD (AND DANGEROUS!) THAT SO MANY APPLIANCES ARE ADDING UP IN OUR LANDFILLS. There should be a LAW requiring appliances to last a certain number of years, and to clearly state their expected life on the appliance when you purchase it. Planned Obsolescence is a common business plan these days, but there must be some control on what is allowed! (I may go ahead and repair this model just because I feel bad adding one more piece of junk to our collective global pile! Sheesh!!) And all those energy star, were so green advertisements? Well, if its soon to be sitting in a landfill, its NOT so green! I am willing to pay more to purchase appliances that will last a number of years, not need many repairs, and function as they advertise... Thank goodness I kept our very first Whirlpool refrigerator - never needing any repairs and still running like a tank out in the garage. (So I know Whirlpool, at least at one time, was able to build a quality product!)

I purchased my refrigerator from a home improvement store in October 2013. We paid around $2,600 for it. About a week ago we had a power outage and the refrigerator never came back on. I called Whirlpool repair since it was still under warranty. The said it would be 9-2-14 before they could come out. Today they came, did not have the part but said it would be here in 10 days. We will be without a refrigerator for 3 weeks. This is totally unacceptable but what can I do?

Not as big as appearance would indicate. Very disappointed in actual usable space. You have to open both doors to get anything but the smallest items out. Had unit for less than a year and had to get freezer door seal replaced. Glad we got the extended warranty.

I purchased a whirlpool under counter oven - my main reason for not buying something cheap was the safety of my family - I chose the AKZM656 eye level oven. The stove is about two years old, but we do not use it that much. Two days ago my wife set the timer and placed a dish in for cooking; she then went outside to water the garden. About twenty minutes later she returned as something was burning- the oven reached a temperature of 350 degrees and would have burnt the whole kitchen down if she did not spot it. Now surely the oven should be designed to switch off if sensors fail? I reported this to Hirsch (Ballito) but they say they have no one servicing the Richards Bay area. I am not sure if this stove should be fixed as it is obviously not safe and makes me wonder how Whirlpool get safety standards passed on these items. Surely you expect better when buying a well-known whirlpool brand?

Back in the day GE appliances were made to last and last - the only one I have found close is Whirlpool. They have style, dependability and long lasting products. My washer machine has a ton of features and I didnt pay more for any of them.

WRF993FIFM00 refrigerator is a LEMON - I bought my $3000 refrigerator just after Christmas. In seven months, it has failed three times and I have been without a refrigerator for a cumulative 7 weeks so far. Each time it failed, I lost all my food, (but not until after wed been eating compromised food). If you buy a fridge, I strongly recommend getting a thermometer, because we learned the hard way that these Whirlpool units can just stop cooling properly and you wont necessarily notice that it is above the FDAs recommendations for food storage. Anyway, after each call they will make an appointment a week or two out for a tech to come out, who then orders the parts that take weeks to come in. Now, my third service call in and the SAME PARTS have failed again and I am again without any refrigeration and they have no idea when the parts will be in. This has been an awful experience, and Whirlpool could not care less. DONT buy their products, under any of their names. IT IS TIME FOR A CLASS ACTION LAWSUIT. Too many folks have spent a lot of money and have been burned by Whirlpool, not to mention becoming ill from improperly chilled food!

After a days work Old Grumpy around 7:00 PM drags to sink, fills pan with hot water & soap; starts scrubbing forks, spoons & occasional cereal bowl. I prewash everything placing it in the dishwasher, it takes it a week to reach 3/4 full: use for sanitation.

I have a Whirlpool oven and dishwasher and have had nothing but problems with them both since day one! Our oven went out Christmas and couldnt get service on it and we were entertaining for Christmas. DONT EVER BUY A WHIRLPOOL PRODUCT!!! If you do you have no one to blame but yourself.

I had the bearing go bad in the tub after a few years of service. It cost hundreds of dollars. As an engineer, I look at this and it is a design made to fail. The seal design is inferior compared to old washers that had a shaft seal made to be on a spinning shaft. This is a rubber lip seal that is going to wear because it is using washer as a very bad lubricant! When the seal goes bad, and it will, the water runs down to the bearings and destroys them, and you have the replace the whole tub as a $300 part!

Fridge residue - ED5FVGXWS07: Well, I gave it a long time and this is how they make Whirlpool refrigerators! I had a GE for 20 years and was so looking forward to this new one. What idiot designs a fridge that leaves water stains like this? And, the water falls onto the floor when refilling a water bottle plus there is no catch for the water. Argh! I really dont want to live with this for 20 years! Their resolution was to get a water softener; really?! It has a filter built in. They refused to replace the fridge.

I bought a Whirlpool refrigerator from Home Depot. It didn work. I had to wait for a week to get a new fridge.. I also bought the 5 year warranty -- its not worth the ink its written with. MAYTAG DOES NOT ANY CUSTOMER SERVICE. THEY DONT KNOW A THING ABOUT CUSTOMER SERVICE.

Apparently, Whirlpool selling all their rejected faulty washing machine in the market. The trick they are playing is the machine being sold with one year parts-labor warranty; They wont replace these machines with a new one because they know that these machine will never work, consumer will buy the faulty machine, obviously it wont work so consumer will call for service. The service guy will say that “oh! Machine needs a part and then the customer service will say “the part is being ordered”, “wait”, then the service guy will come with the part and after wasting some time he will say “Oh! The machine needs another part, and again customer service will tell the consumer that “you keep calling us”. One year will be gone! Bottom line – faulty machine is sold, Whirlpool made profit, buyer is robbed. I am one unfortunate customer who purchased Whirlpool Washing Machine which never worked as it is a faulty machine which should not go to the market at all; Whirlpool made money on my hard-earned dollars and I been robbed.

Purchased a Whirlpool double door refrigerator and within a year the freezer and refrigerator doors were severely out of line. Called repairman who said the risers were broken, they were plastic and needed to be replaced. We did that. The doors were again out of line so badly that you had to push the refrigerator door side hard to get it to close. Repairman came today and stated he would recommend ditching the refrigerator as the risers in the bottom of the refrigerator are made of plastic and will continue to break. He leveled the doors but stated that they will continue to become out of line again.The repairman stated that this is a design defect in the Whirlpool refrigerator and he has replaced the risers in many of the refrigerators repeatedly. As if the refrigerator isnt enough, we own a Whirlpool Duet Washer and Dryer. Within 3 1/2 yrs the motherboard went bad in the washer and we had to replace it. The part and labor was almost $400. Whirlpool considered us a valued customer and offered us a comparable washer for $500 and they would take ours away for $20 extra. Only problem is that our original washer was $1,000 and the comparable was not as large as the one we had and did not have the stainless ours had.All I can say is if were valued customers I would wonder how they treat their less valued customers. All of this is to say that I will no longer purchase any Whirlpool products. Not only are the products below par but the customer service is non existent. They really do not care if they lose customers or not. They dont want to hear your woes about their appliances.

This dishwasher is noisy, it does not get the dishes clean, and anything that is remotely lightweight gets thrown all over. This must be one of Whirlpools cheapest models as I have had other Whirlpool products and they were fine.

A-10 error on display ultimately means needs a new pump. The washer (model WFC7500VW 2) is 3 months, 9 days old and is now unusable. I cannot get any service (under 1-year manufacturers warranty) because the sticker inside the door with the model and serial # is missing (i.e., it was sold to me by Homedepot.com without a serial # on the door label, sticker is intact and is brand new and apparently was printed without a serial #).I made multiple calls to Whirlpool in Benton Harbor, Michigan and finally spoke with Courtney (who states she was a supervisor) pretty much said all they will do is to reprint a label from the factory and I should have it in 7-10 business days. They refuse to stand behind their product and authorize timely repair of their product they sold to my without a serial # on the door tag from the factory. I have to wait to schedule factory warranty repair until I get the new label (probably 3 weeks plus without a usable washer). Courtney refused to contact me via email for any of her contact information or to supply verification of conversation or promise of a new factory label. Also, she refused to try to authorize any type of manufacturers warranty to fix the brand new unusable washer!

After being a faithful Whirlpool consumer for years... I no longer have any faith. I purchased an entire kitchen suite. The side by side refrigerator Nov 2013. The first refrigerator was delivered with the side cabinet deeply dented in several areas. Another was delivered 4 weeks later. Silly me... I thought, Okay, no big deal... what could go wrong? I didnt take time off work again to receive the replacement. My son took delivery (never looked at it). I get home... the front of both doors looked like they had been kicked in all the way across! To add, the cabinet sides were textured (not smooth like what I ordered) and the door handles didnt match the other appliances. So, I called HDepot & called Whirlpool (only to be on the phone an hour each time due to high call volume. Imagine?). Then Whirlpool reps are talking to me like I am some sort of idiot... saying that the refrigerator was EXACTLY the same... not possible that the handles or sides were different!!! Because it was damaged (and I mean ridiculous! ) another 8 weeks for a replacement. Frig #3 arrives and I take time off to receive it. Ah, the right refrigerator... but again ~ handles dont match. Not POSSIBLE.. Ms. _ _ _ _... it is the exact refrigerator, those are the same handles. Hours and hours on the phone to HDepot and Whirlpool. Finally, HDepot rep has a WP rep at the store when I call, and bingo! Oh yes, there are two styles of the Exact same model. The handles are ordered... 10 weeks later I finally have matching handles! But, wait... gets better. The fridge has been loud from the start, CONSTANTLY running but, not cooling some areas and freezing in others. Then when you open the freezer it is like a burst of winter wonderland is unleashed in your face. There are sheaths of ice building up on the top of the inside door. Hmm, I think what is going on? The Whirlpool designated repair company comes out. Ah, well here is part of your problem. When the refrigerator was being put together they left a few thicknesses of blue packing tape between the door and the rubber seal in the freezer. The rep tried to fix it to no avail because the door was also warped. First they were going to replace the door. Waiting for another 10 weeks. Nobody calls, whats going on? Oh, never mind, or rather... that was never happening. I have spoken to many reps with Whirlpool, I have been polite with all. In turn, from most I get curt hard ball back. The offers to resolve this from Whirlpool have been ridiculous. I am sorry for my loyalty to Whirlpool, as it has not been reciprocated. I have had two more deliveries - both the wrong unit! I never thought there were others out there. What a mess. They should recall.

I have had Whirlpool appliances for a very long time. However, I am extremely dissatisfied with the purchase of my last Whirlpool washer a couple of years ago. The washer is extremely noisy, to begin with, and I complained to hhgregg about this. They delivered a couple of other machines, all of which were very noisy. The latest problem with this machine has been with the tearing my clothes. My clothing gets caught under the agitator and the items tear. This is a poorly designed washer and I wish I had never purchased it. I was thinking and wrongly so, that the washer would be as good as my previous washers. Well, I was so very wrong.I wish to know what you are going to do for me with this problem which is so very annoying and costly.Marjorie **

Oct 14th I walked down to our basement to find it flooded. Turns out the leak came from the solenoid that controls the water feed to our Whirlpool Gold Series refrigerator. Now, some $28,000 in damages later - floors/cabinets/walls/electronics - you name it. The repair company said that they replace these units a lot as it is simply a faulty design and Whirlpool knows this as this part is very difficult to obtain - too much demand. Well aside from the cost, the inconvenience, and the rise in our insurance rates the repair person said there was a good chance of the new part failing as well - it just cant take the water pressure as it is just cheap plastic. My advice - stay away from Whirlpool!

Updated on 12/28/2020: I purchased a 28 cu. ft. side by side Whirlpool refrigerator less than 3 years ago (Feb. 18). The icemaker dispenser paddle quit working nearly a year ago and there are no replacement parts supported. Today the ice maker quit making ice. This is crap for a major appliance that youd expect to go twenty years or so. Very dissatisfied. Dont waste your money on this stuff.Original Review: I purchased a Whirlpool side by side refrigerator about 2-1/2 years ago, paid $1,800+ for it. Now two months ago the ice maker dispenser through the door quit working. I replaced the auger motor and that didnt help. Now the parts department says the actuator panels are no longer available. This is planned obsolescence to the Nth degree. No support for a major appliance less than 3 years old. Whirlpool SUCKS!!!

After having my Whirlpool side by side refrigerator ice maker replaced 4 TIMES in 10 years, I finally found a permanent fix for it: an Igloo counter top ice maker for around half the price of a replacement Whirlpool ice maker. Unlike the Whirlpool ice maker, it makes ice. I promptly removed the Whirlpool ice maker FOR THE LAST TIME, and sent it to the dump, where it belongs. Goodbye Whirlpool! If that is the best you can produce, you will not receive any more of my hard earned money!

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

I have had my whirlpool oven for approximately 6 years. This will be the 3rd time I have had to replace the thermal fuse. For the last three times I have used the auto clean, it blows out the fuse. It has cost me $110.00 each time I called my appliance tech to replace the fuse.

Washer keeps saying F1 and it wont spin. In the middle of load it will stop and it would say F1... It started just a year when we bought it. Now its two years. Its really broke. Before it would say F1 then I give an hour then try again and it works but now no matter what I do it really wont work... I dont know no one who could help me whats this F1... So sad. Its not cheap washer but its junk.

The agitator is higher than any I have seen and when we washed aprons that have plastic buckles on them, they get stuck under the agitator. When complained their solution was to use laundry bags to wash 15 aprons in, they are long aprons. Paying a lot of money for the machine and it being commercial I didnt think we would not be able to use it. The whole machine shut down when three of the buckles got stuck. The washer is model # CAE2793BQ and I would suggest that no one purchase one of these machines.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

I bought these products 2 1/2 years ago along with a dishwasher and Microwave, all which are Gold Series. The first month my Microwave broke. Instead of a certain part that they used to use, they now use a Capacitor instead and it broke. The repairman fixed it under warranty, but told me Ill be seeing you again. Then, my oven occasionally says Function not available. Whirlpool wont tell me what the problem might be and they have nothing for troubleshooting this problem in their manual. My only solution is to reset the circuit breaker and then it works for awhile. Now, My refrigerator has ice building up at the bottom of my freezer and leaking all over my floor. I found a Whirlpool bulletin online which explains that this problem is because of a defective part (Grommet) and that they have a replacement part for it and you can get it by calling their customer service department. Why didnt they send out recall notices to their customers?So, on 8/10/2015 and 8/11/2015 I tried getting this new p-trap part, but for two days now Whirlpools computers arent working and they have no other way of looking this stuff up. Very poor customer service and I also waited for a half hour on the phone to be told their computers arent working. How about putting a message on their pre-recorded message letting customers know their computers arent working?

We bought the Cabrio less than 5 years ago. First of all, a high-efficiency washer should not require an extra rinse after each wash, but this one does. I cant see how thats being efficient. The washer, even for a small load, can take up to 54 minutes, and then when you tack on an extra rinse, its well over an hour, so what you may be saving in water, youre spending in electric and wait time. And then, there is still a soap/water scum left on the clothes, which is only evident on the darker clothing. Now, just recently, the washer is stopping, and NOT unlocking after about a minute into the start cycle. I will have to cancel the wash, turn it off and unplug it before I can get it opened. Im sure its something to do with the electric panel, which after reading the reviews, we are not going to fix, and we are headed out to buy the traditional top loader, NOT high efficiency, which I suspect will still be more efficient than the Cabrio.

Washer does not clean clothes period. Darks come out covered with white soap residue and smell dirty regardless of how little soap is used or with using extra rinse, which takes 84 minutes by the way. Whites only seem slightly cleaner since hot water is used and you cant see the soap residue. If you wash more than 5 or 5 items at a time some do not even get completely wet. Just waiting for it to break down next according to the other reviews. I spent a lot of money to get a nice washer and dryer and ended up with junk. Id rather have an old 1970 washer, probably designed better and most likely would clean better.

I purchased 4 whirlpool appliances at Leons in Mississauga. The side by side refrigerator was replaced within a few weeks. Got a new one and have had that one fixed at least 3 times already. The stove was serviced 3 times now, the washer broke so many times. They gave me a refund. The microwave broke as well. They told me it was not fixable, then I called Leons and they said it was too old. It was only 18 months old. Did not get anywhere with the microwave. Had to buy a new one. The only appliance I had that didnt break was the dryer. So far. The fridge now has broken inside, the crisper wont slide in and out at all. Cant be used. I bought a warranty on all the appliances, and even though I had a warranty, when a coin got stuck in the washing machine because the drum inside kept banging because it was in need of new struts, they still charged me 135.00 to fix it. Two to three weeks later a repairman came and put new shocks on it. Finally after having it repaired about 5-6 times in a year and half they gave me a refund at Leons and I went to pick out a new washing machine. Overall I have spent about 6-8 hours on the phone complaining and making appointments with Whirlpool Canada.

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

November 4, 2017 we purchased a 2018 Tiffin RV with a Whirlpool 3-door refrigerator/freezer. We did not use the RV refrigerator until our first trip to Florida January 2018. Immediate problems with the freezer icing up on freezer door and icing up in the top 2 shelves of refrigerator. Milk, fruit, even cheese froze in the top of the refrigerator. Bottom freezer door froze so bad I had to yank on the drawer very hard to even get it open & chunks of ice would fall off the door on the floor outside once it opened. Called Whirlpool warranty service phone number two times 2/16/2018. I wont go into all the details but we were on hold for a 90 minutes and were transferred 7 times by the automated system. Talked to one person, Lindsey, who immediately transferred me again to RV Dept. No one ever answered. System kept saying, Please wait. Then just disconnected and another recording came on saying to call back. We did not after this fiasco! February 19, 2018 we called Tiffin MH & told them about the NO CUSTOMER SERVICE from Whirlpool. They told us to call Sears in Sebring, FL. We did. If we wanted Whirlpool service to bring the motorhome to them & the warranty only covered parts NOT labor or service calls. They did not want to work on it. March 13, 2018 We went to Tiffin MH Service in Red Bay, AL. Earl called Whirlpool tech, Steve, & tried to explain the problem. Steve told him he did not talk on speaker phone & told him very hatefully to put him on the private line. Steve just very angrily insisting that Earl had him on speaker phone. I do not understand Whirlpools Steve issue with being on speaker phone? Finally Earl got him to listen to our refrigerator problems as he stood there at the refrigerator going through each issue step-by-step. Steve said to put silicon in the seal & that Whirlpool WOULD NOT replace a 3 month old refrigerator that actually had only been used 2 months. We found out later Tiffin is going to replace the refrigerator.

I join the many who have posted about the Whirlpool Cabrio Washer cracked lid issue. Our Whirlpool Cabrio WTW7800XW2 glass-lid washer suffered the same (inevitable) fate – cracked plastic on the lid at the hinge stress points, after the washer was beyond warranty. Same story - runaround/no help from Whirlpool. Finally bit the bullet and shelled out the $200 for a new lid. HOWEVER, I didnt want to just replace it and have the same issue down the road. I removed the spring-loaded units that support the hinges, hoping to just remove the springs to release the pressure. I found that the springs are integral to holding all the components together in this unit. These are extremely heavy-duty extension springs, so I took them to my hardware store (TrueValue) and found springs the exact same length, but with a smaller wire diameter and thus requiring less force to extend. I replaced the original springs with these (Century Spring Corp. - #C-143 - 9/16”x3”x.054”). The lid operates perfectly, and now there is very little resistance at the hinge stress point. The only difference is there is no longer a “damping” effect when lowering the lid - it must be lowered manually rather than being allowed to fall on its own. That’s a small correction in habit, but will ensure that the replacement lid lasts for the life of the washer.

Read reviews on the same washer (Cabrio Whirlpool) that I had purchased in January 2017. I have the same problem everyone else has with it, not cleaning the clothes. It was such a disappointment. Had a Whirlpool front in loader for 15 years. Loved it! But the washing machines without the agitator on it is a laugh. What person thought up that design. What a joke on the poor unknowing people that purchased one. Im also upset at G&H Appliances for not standing by their products they sell. Found out that Lowes has a 30 day satisfaction guarantee on what they sell. Not buying from Lowes and buying a washer without on agitator on it. Was two big mistakes I made. I wanted to help out a small local business, but wont be doing that again. They sure are not worried about me.

We bought all Whirlpool Gold Appliances when we re-did our kitchen 5 years ago -- fridge, d. washer, oven, glass top stove, and microwave. Recently I noticed a pool of water in front of the fridge. Turns out there is a sticky grommet problem that prevents moisture from draining into a pan on the inside back bottom of the fridge. Whirlpool will send you a replacement part that is totally different than the original poor design (a long hose affair) BUT wont pay for the labor to put it in unless the unit is less than 2 years old.I watched a video showing how to do it, but it looks pretty tricky and involved plus risky because you can break the drain pan in the process. Spoke with a Whirlpool rep and a supervisor -- both admitted to a quality problem but got nowhere on the labor. Theyre sending the part, and the supervisors supervisor is supposed to give me a call, so well see if they eventually do the right thing and cover the labor. I mean cmon... the parts obvious a bad design, or they wouldnt be sending a totally redesigned part! Covering the labor only if its two years old or less? Even the Whirlpool techs online are saying the problem happens after about 4 years! The grommet gets sticky and wont drain due to heat from the compressor, and that takes time to happen. Ill update this when I hear back from Whirlpool.

Purchased a Whirlpool range. Shopped around for several weeks before I found what I thought was a good price and with a rebate! Ive owned the stove for 2 months and 7 days... guess what? The stove broke. The burners popped. I called to have it serviced and remember that it had a rebate. I never received any paperwork on the rebate but figured its Whirlpool, good company. Wrong... its not that I didnt have the rebate paperwork but the rebate has expired... even though I didnt get any paperwork nor was there any mentioned of a time frame. Dont get me wrong if it had been 1 year or even 6 months... really 2 months!!! So not only did I not get the rebate of $100.00 I have a broken stove! So tired of being ripped off!