I purchase a Cabrio WTW7800XW0 3/28/11. After the year warranty I started to notice sand like substance in the drum of the washer, which lead me to look around the drum. I noticed that the light was completely rusted and flaking, the area around the light was rusted as well. I call customer service at which time they said it was not warrantied, but they sent me out a new light. This did not repair the problem! The rust has continued causing the area around the lid joint to break. Also the area around the bleach dispenser is showing rust- the same side as the light and the lid break. They have said this is not covered and only agreed to pay 1/2 of cost of materials (no service).

I spent the extra money and bought a very nice looking Whirlpool range and oven. Within months, it started rusting. I keep a meticulously clean kitchen and Ive never had this problem with any other appliance. I sent letters to no avail. They said that their warranty on rust was 30 days! They refused to do anything about it and told me to go ahead and sue them. Terrible product. Defective from the factory. Do not ever buy a Whirlpool product as they do not stand behind it.

We purchased our Whirlpool refrigerator Model # WRT138TFYW on March 2012. We first started noticing that the eggs and the milk started to get icy. We lowered the setting from the normal setting to the lower setting. This seemed to work for about 5 months then things started to get icy again and this time it started making a loud noise. Then in August, we called Whirlpool, told them what it was doing as it was still under warranty. They sent out A&E, the biggest crooks I have ever dealt with as well as rude people. The service guy said it was probably the Frost board. He ordered the part and put it in. Afterwards, we asked him why it was still making such a ruckus. He told us this was normal. Now we arent a professional and dont know about Appliances so we took the technician for his word. Then this past December, the refrigerator wasnt cooling as good. The next day we noticed that things in the freezer wasnt freezing either. We called Whirlpool, told them what was going on and that they needed to get someone to fix it. This was when we found out that the refrigerator only has a one year warranty. I got them to agree to pay for parts and labor after getting down to the fact that this problem went back to the very first time while it was still under warranty. They sent out A&E Factory Service, again the biggest crooks there is. They checked the refrigerator and told us that the compressor and evaporator was bad. They ordered the parts and that was the last we saw of them. We got Whirlpool to send someone else. Now up to this point, I have to give them credit because they have been really nice. Then when the other technician from Americus Appliance (Very good guy, would recommend to everyone) asked why both parts were ordered, we told him that the technician from A&E said it needed them. He then installed the Compressor and told us that there was nothing wrong with the Evaporator that he could tell. He then filled it with Refrigerant and the freezer was getting very cold. Then about an hour I went to check to see if the refrigerator part was getting cold and it wasnt. I checked the freezer at this time and noticed that the freezer was getting warmer. We then called the service guy and he checked the refrigerator. This was when he told us that there was a leak in the wall of the unit and it couldnt be fixed. We called Whirlpool and told them what the technician said and asked them what they were going to do. They then said they would send everything to the exchange team and go from there. Now we are waiting to see if they will replace the refrigerator. Personally after having to replace a Brand New Washer a year and 2 months after the purchase and possibly now a refrigerator that is less than 2 years old. Buyer Beware. Check out the warranty on a GE. They have a better warranty on their refrigerators than Whirlpool does.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

The lid stopped locking just over one year after I purchased a Whirlpool Cabrio top load washer, which disabled the washer from washing. After investigating, it seems the electronic control board needs to be replaced, which will cost $400 just for the part. I have a large family, including a disabled child, and a washing machine is mandatory necessity that I cant afford to replace after only one year.

I had my kitchen remodeled and purchased a Whirlpool built in electric microwave and lower oven combo (Models WOC54E and WOC95E). I selected this product because it had the right dimensions for my kitchen and I thought Whirlpool was a quality brand. Well I was completely incorrect about the latter point. Within just a few months, I noticed a drip line in the microwave door, between the outer and inner panel that could not be accessed to clean. I barely used the appliance and had no explosions in the unit that would account for this unsightly stain. When I called Whirlpool, they told me that cleaning and resealing the microwave door was not covered by warranty, and if I fixed the problem, then I would invalidate the warranty on the appliance. I had no choice but to live with this drip line, which has now been joined by others. I can think only that this is caused by condensation and that the door is permeable to moisture.Then there is the oven: When it is in use and for at least 30 min after, the fan on the unit is deafening. Not just a little noisy, but really loud. This is my first experience with Whirlpool and its products, and I would NEVER purchase others. They are not inexpensive and are clearly of substandard quality. The fact that Whirlpool is prepared to put a defective product on the market and then not be prepared to fix problems with the unit is appalling. DO NOT BUY WHIRLPOOL.

We purchased a Whirlpool conquest from Lowes in 2009 and purchased a Lowes warranty. About 2 years ago we started seeing hairline cracks on most of the drawers and shelves. I complained about it last year and a lady from the Facebook page did offer 50% off new ones. Since then we have not been able to afford to get any, and today we lost our last shelf. If I wouldnt have checked it, it would have broke along with anything on the shelf. I have never seen such horrible parts. We have another small very old fridge that has help up better than this. At this point I will never buy another Whirlpool.

I purchased an over-the-oven microwave in November 2020 (Model # WMH31017HZ). It worked until March 2021 then began tripping breaker. The Safety department at Whirlpool stated that I have to get a dedicated circuit. After spending an enormous sum to get that dedicated circuit the microwave worked until April when just opening the door caused a spark that the electrician and I observed. By now I am sure that I purchased a defective unit but Whirlpool was not believing it. (As as aside, expect to stay on hold for at least 10-30 minutes when you call Whirlpool).May 7th the serviceman from Guincho ordered parts that was needed to repair the oven. As of May 30th the part still had not arrived. Finally, after multiple calls and excessive hold time, Whirlpool agreed to refund my purchase price and as of this writing on July 26, 2021 I have not received it. In the meantime I purchased another brand microwave and have to look at their defective one until they decide to pick it up. They have lost a customer.

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

I will never buy a Whirlpool product of any kind. I bought a gas stove and its a piece of **. Won’t even light. Only way to start it is start boil then switch over to bake then it wont light. So please I ask that you make a product thats worth buying.

I purchased a Whirlpool 40 gallon gas water heater from Lowes approximately 4 years ago. As of yesterday, the pilot will not light. I assume the t-couple is bad. But in the process of doing some research, I could not help but see that there is a quality problem with heaters manufactured around the time mine was. I dont have the model number with me at the moment. I would like to know what the permanent fix is for these heaters.

I purchased a Duet Front Loading Washer (model WFW9750) in May 2010. In September 2011, the noise level had become intolerable. I called a local service company. They advised me that the main bearing was bad. It would cost more to repair than what it was worth. I contacted Whirlpool. They could not do anything unless the machine was inspected by one of their authorized service companies, which they scheduled. Two weeks later, A&E Factory Service arrived and confirmed that the bearing is bad and the cost to repair will be $1,542.06. Whirlpool customer service transferred me all over the country to tell me that the machine was out of warranty and there was nothing they could do.

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

Our water heater pilot light has started to randomly shut off leaving us with cold water to shower in on numerous occasions. We hired a local appliance company that we are familiar with to come out and look at it. The tech thought that replacing a part would fix it. It didnt (which I will take up with them). After doing what Whirlpool asked us to do it still is not working. I called them back to warranty the tank and the rep keeps repeating it is a limited warranty so basically I have to pay the service call and labor charges to look at, repair or replace which is going to cost nearly as much as it will to just buy a new one.

We bought a Roper refrigerator about seven years ago. Less than two months later two of the cheap plastic door shelves broke and we had to buy replacements at over $20 a piece. Since then weve had to replace one more. Tonight another one broke so well have to fork over another $20+ to replace this one. I checked the Whirlpool website and they have the exact same flimsy plastic shelves as the Roper. I will be in the market to purchase at least three refrigerators in the next two years and you can bet that they wont be either Roper or Whirlpool. My advice to anyone in the market for a refrigerator to steer clear of these two brands as their shelving is cheap and shoddy.

Large tub capacity. Door opens wide without stopping. White Finish has not faded or chipped. Quiet and rarely makes noise even when overloaded. Machine bought 12 years ago and has never needed a repair visit. It has been moved from 2 different locations by using the special brackets. Easy to use detergent holder and fabric softener.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

We had our microwave and stove delivered in October, 2015. We had 4 deliveries of the microwave. The first two were damaged, the third needed a new fan motor and the door was not straight. They wanted to send parts to fix but we could not see spending all that money for a brand new microwave to have parts put in. I complained a lot to both Whirlpool who would not replace it and ABC Warehouse who finally agreed to replace it with a brand new one. The 4th is good. (so far).Our stove has a flaw in the glass top, the drawer doesnt close properly, and there is a piece of metal sticking out from the lower right side of the oven door. ABC says they cannot do anything about it and Whirlpool says it is under a parts warranty so it has to be repaired. I even spoke to supervisor Kimberly at Whirlpool. Got same answer. We are very angry and disappointed. As I told the Kimberly, Whirlpool got every penny they asked for. We paid for brand new in perfect condition and got a stove that needs fixing. We will never recommend Whirlpool as a Company for appliances and based on all the negative reviews Ive read, neither will a lot of other people.

I am also disappointed with this manufacturer. I recently purchased an over-the-range microwave oven model KHMS2056S. Within 45 days of use, it quit heating. I initially established a service call through Kitchenaids web site, with the first available weekend appointment approximately 2 weeks away. When the contracted service represented arrived (A&E), he asked me for a cup of water and placed it in the microwave, along with a temperature meter. After running the microwave for 45 seconds, he informed me that microwave was not heating. This was the extent of his troubleshooting, only to confirm what I had already reported in my initial service appointment description. The next step was to order parts and wait another 10-20 days for a new service appointment. When I challenged the technician on this, he stated that they were required to verify the problem and check the model/serial number of the appliance. But these were also provided through the automated service appointment system. Thanks to Lowes who allowed me to return the item, even though the purchase date was outside the 30-day window. It seemed obvious to me this warranty contractor was simply creating multiple service calls to inflate the repair costs. And ultimately the consumer pays this.

We have a built in double oven and we had some early problems with the thermostat. And from time to time the clock resets to 12:00 oclock when there is no other power outage indications. Its also been a challenge understanding the instructions sometimes.

Bought a new side-by-side in 7/2020 from Lowes in Keller, Texas. Salesman won me over with the buy American pitch claiming if the need ever arises for parts I would be far better off than with LG which orders their parts from South Korea. I bit, and bought, and now regret. The refrigerator dispenses water randomly and I must keep a glass under the dispenser all the time and empty it when it gets full. Under warranty they say! Well here it is September and after being on hold for an hour each time (6 times as of today) I attempt to get help they tell me that the part W11293378 is not available and will not be made until after this month? BEWARE this brand. This is a poorly ran company and buyers would be better served to look elsewhere.

I bought a Whirlpool Cambrio washer/dryer set last year. I hate them. They dont get the clothes clean, let alone wet! I couldnt believe it! I put my grandsons bib in the wash and it came out completely dry with the stuck on food still there. My husbands shirts still smell like the cologne he put on! I asked a Home Depot sales person about this and he says, yeah, we hear that a lot. !!!!!!! Im going back to a washer with an agitator so that I know my clothes are being cleaned. This whole water control business is insane. Whats the point if you have to wash the clothes several times to feel like they are marginally clean? The problem is that the industry has decreased the amount of models that still have an agitator so my selection is very slim. First and LAST time I ever buy Whirlpool.

I purchased a Whirlpool Duet front-loading washing machine on September 27, 2010. By October of 2011, it was making a loud grinding noise during any spin cycle. I called for service and was told I needed new bearings which entailed rebuilding the machine. I had purchased a 5-year extended warranty. I was originally told by the warranty company they would replace the machine.After waiting two months, and after several contacts made by me to the retailers customer service, I was told the machine would not be replaced, but repaired. After the repair, on January 6, 2012, the machine now rattles and shakes so much during the final spin cycles. It is literally impossible to have a conversation with someone standing next to you in the same vicinity as the washer, it is that loud. I am sorely disappointed with the Whirlpool line of products and with the retailer who has been dragging their feet on customer satisfaction.

In November 2014, I purchased a Whirlpool 22 cu ft side by side refrigerator from my local appliance store. During that short time, there have been 4 instances where the ice clumps together and gets stuck, causing a large amount of ice to dump inside the freezer door. When the door is opened, the ice falls out onto the floor. I usually spend 10 minutes picking up ice and wiping up my kitchen floor. I have had the local store repairman over. He told me that was normal. Two things are seriously wrong with that statement. When I spend 1600.00 for a brand new appliance, I should be able to depend on the fact that it will function in at least a somewhat acceptable manner. Additionally, that statement by the repairman convinced me that he was not really interested in fixing the problem. I really dont think the normal operation of a new appliance is for it to make frequent, large messes for the owner to clean up. This appliance is junk and you would be foolish to purchase it. Spend a bit more money and buy a Samsung or LG. Save yourself the frustration and sense that you have been cheated and deceived by Whirlpool. I will never buy this brand again.

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

I have a microwave (Model: MH1150XMQ-0) in my summer home. The microwave gets little usage but the door has cracks in all the corners. I have two other friends with the same problem. This appears to be a design flaw and should be corrected. The microwave is still useable but I do not know how safe it is.

Four microwave ovens to finally get one that works. Four months after purchase, the French door fridge accumulated ice, 3/4 thick, in the bottom of the freezer compartment. I had no knowledge of this until the drawer became difficult to open and close. Lowes is replacing the unit.

We originally became alarmed by an awful smell and noticed that our Whirlpool Conquest side-by-side refrigerator freezer/fridge was not keeping food items cold. Upon further inspection, we saw that the compressor starter in had started fire and melted. Our refrigerator model #GS6SHAXLS42 and serial #SM3832794.

I wrote down names, but I will not say them here. I found many recall sites on Whirlpool Cabrio WTW6200vwo for washer tub bearings. Which mine are bad. I called and logged my complaint but they say they have NO recall on any of their products and will send someone out but will charge me a service call unwarranted and parts if needed. I told them there are many websites that recall their tub bearings but they refused to fix the problem on recall. I dont have photos due to bearings are under the tub.

IM OLD AND DISABLED WOMAN. Bought a brand new $800 Whirlpool top loader washer and it wont work after not even a month. Called whirlpool and had the worst customer service from Tammy. I have to wait to compose myself to call back cause the washer is junk... F9E1 SENSOR. IM NOT A MAN! Worst customer service. Thought my washer would last longer. Its been 1 hour 45 minutes. Wont turn off. I CANT unplug TAMMY! IF I COULD I WOULD!

The shelves in freezer don’t lock into anything so if you don’t balance the food right on the shelf it will tip over. I had to replace the fan motor in freezer. The refrigerator is only 4 years old. The little tray under the water and ice outside of door if you shut the freezer door too quick water from tray goes everywhere. The water filter cost $50.00. If you have bad water you will need to change it twice a month.

We purchased our Whirlpool Front Loading HE Washing Machine a year and ten months ago from Future Shop, and now it has failed. After paying about $100 for a service call, we were told we need to order a motor control board that will cost an additional $397 plus tax, plus installation. Because it is off warranty, this means my $1030 washing machine that is less than two years old will cost me about $680 to repair! My parents old top loading washing machine still works after 30 years. And now I notice that so many other people have had the exact same problem. Why hasnt Whirlpool fixed this issue? This is criminal! What on earth is going on here? I was under the impression that Whirlpool was a top-notch brand.

Whirlpool gold bottom freezer is 2 years old. This model has a design flaw. And due to this the drain is frozen in the bottom of the freezer. Water is leaking onto the floor. I called for service and whirlpool is charging me. To fix a problem that is their fault. This is unfair.

My 15 year old front loader quit working and was going to cost more to repair than we thought was worth it. So, we went shopping at Home Depot and based on discussions with salespeople ended up with the Whirlpool cabrio toploader. What a mistake. I am so disgusted with this washer I dont even know where to start. If there was any way we could return it we would do so. The clothes come out wrinkled, twisted, absolutely covered in pet hair and detergent and fabric softener residue. Yes, Im using HE detergent, in the correct amounts. Yes, Ive read the manual front to back. Yes, Ive tried all the troubleshooting suggestions. No, they dont make a damn bit of difference.I would give anything to have my old front loader back. It was a great little machine that did a wonderful job of cleaning our laundry. Pet hair was washed off, I could lay things out to dry and they werent all wrinkly and did not require ironing. Just about everything that comes out of this cabrio machine that I lay to dry needs to be ironed before it can be worn. It is just a horrible, horrible machine and Whirlpool should be ashamed of themselves for foisting this off on unsuspecting consumers.

I have had this Whirlpool Cabrio washer for 4 years. I had to rebuild the drive unit once and now the control board is bad. If I didnt do my own repairs I would have spent well over the cost of the washer in the 4 years I have owned it. This is the worst washer on the market. Not to mention Whirlpool support will not work with you at all. DO NOT BUY THIS PRODUCT.

After 7 attempts to fix my 6-year-old Whirlpool Front Load Washer (original price $991.00) I had to trash it. Then I stupidly bought another Whirlpool Front Loader (WFW75HEFW) Feb 2017. It has not worked properly since day 1. The clothes come out dripping wet. At first I thought I was doing something wrong. I tried every cycle, limited amount of clothing and ran additional spin cycles to no avail. Finally I gave up and called for service.Whirlpool is very much aware that a number of their machines came off the line with defective spin bearings but they wont admit to it. Instead I am expected to have it repaired! It involves the entire inside of the machine being rebuilt. Its a 2 man job that will take 3-4 hours.This is totally unacceptable and it is obvious Whirlpool does not make a quality product nor do they value customer satisfaction. DO NOT UNDER ANY CIRCUMSTANCES PURCHASE A WHIRLPOOL WASHER. They are difficult to work with and I for one will never purchase or recommend any of their products. I purchased this washer from Home Depot and now my only hope is that they will honor my intention of purchasing a non-defective product. If not, I guess Im in for another miserable experience with a Whirlpool product.

Purchased a Whirpool fridge 1 1/12 - after Sandy, used for about 1 month. Now ready to move home and was told ice maker bad?? Thank god we purchased warranty! I want to know why ice maker is bad regardless covered?

I own a Cabrio Whirlpool washer. It already had several repairs and never got my wash clean. I complained to the company, no results. This washer is not even a year old. Why will they not stand behind their products?

I purchased a Whirlpool over the range microwave (model #YWMH31017AS-1) in April 2013, and had it installed in August of same year. It worked fine up until November 2014 - just over one year later. Everything on it works, except for the most important feature - IT DOESNT HEAT ANYTHING UP. Doesnt matter how long you set the timer for - the contents come out stone cold! I called Whirlpools 1-800 number and was told that because I did not purchase the extended warranty, I was responsible for all parts and labor costs. I find this completely unacceptable! I have had cheap $70 microwaves that have lasted 15-20 years. I will never buy another Whirlpool product, and am telling everyone I know to do the same!

Whirlpool customer service is non-existent. I have a Whirlpool microwave that burned up after two months of use, and they sent over a technician twice, in the past three weeks and it is still not working. Now, I am being told that it will take another two weeks before the correct part is found, and the technician is sent here again to fix the problem.I have no microwave now, for what is going to be about 5 weeks, and that is only if they get it right this time. Whirlpool wouldnt approve for me to have it traded a trade for a new one at HH Gregg where I purchased it in Aug of 2011. HH Gregg only has a 30-day return policy, and it went bad after 60 days.

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

It seems the quality issue of the LED of the washer Whirlpool Cabrio. It was broken from the screw part of the glass and the plastic/alloy and the glass. They would charge me $416 to replace the LED but I rejected and was still required to pay $85 for labor fee. I called the company and they didnt admit that was a quality issue but I just found many consumers had the same problem. If someone would like to have a lawsuit, please contact me and I will join.

I bought a Whirlpool refrigerator (model number model ised5lvaxwq00) about 14 months ago. The icemaker would not work when delivered. I had it fixed. Several months later, it quit working. It cost $200.00 to have it repaired. The ice door stopped working. I called Alabama Power to repair the icemaker. He advised that it would cost around $300.00 to repair. We are on a fixed income and cannot afford to have it repaired. On investigation, I found hundreds of complaints about the same issue with the icemaker flap. I would appreciate you trying to eliminate this problem.

I bought a HD Whirlpool in April 2011 and I hate the machine. It does not use enough water to wash clothes. I open the lid every wash and cannot believe Whirlpool can label this as a washing machine; it spits a little water now and then. I am demanding Lowes and Whirlpool to replace the washer. I have used two Kenmore washer for 45 years and I never had any problems. I use hot water to kill germs -- well there is not enough water to drown a fly. How can these manufacturers sell such product and then give the consumer such a hard time when they ask for help. Dark clothes have white residue stuff all over them. I have to hand-wash a lot of my clothes. I have never in 45 years had to do this. I am so mad that Whirlpool is taking everyone for suckers. Now I am sure that there are a lot of people who just never take the time to complain; too much trouble and just go buy another brand of machine. We consumers need to demand that manufacturers sell quality products.

Bought Whirlpool refrigerator Model GB2FHDXWS from Best Buy in July, 2012. I began freezing up immediately. Called Best Buy. They replaced it. Now the second one quit. Freezer doesnt work. Refrigerator motor works constantly. Called Whirlpool and was informed unit only has one year warranty. Got an estimate to repair it. Evidently, sealed unit needs to be replaced at $700. Will never buy another Whirlpool appliance again. Will not deal with a company that will not stand by its products.

Front-loading does not do good job of rinsing. The Whirlpool Duet will not last longer than 2 years. Whirlpool recommends that owners purchase a new washer every 2 years. Whirlpool suggests owners purchase new clothes each week to avoid washing. Any owner would be required to quit their job in order to wash clothes. The Whirlpool Duet front-loader requires 12 hours per load. This means that only 2 loads can be washed in a 24-hour period. Each load requires 10 rinse cycles to remove suds.

I installed this Whirlpool Gold Series oven in December just before Christmas. I cooked a 9lbs Turkey for over 4hrs at 350 degrees (it should have only taken 21/2 hrs at 325) used a thermometer to test the temp. Well the breast part was fine but later in the evening I removed the entire turkey only to find that the legs, thighs and bottom of the turkey was still RAW. Lucky no one had asked for that part of the turkey. Next I tried a small prime rib roast. Same thing happened. The top of the roast was fine and the bottom was RAW. I dont dare cook anything in the oven now. Called whirlpool and they are going to send someone to look at it but I wont hold my breath for any results. After reading the same complaint on several reviews and the TV show Marketplace it seems to be pretty standard for this product.

I bought the WTW4815EW0 Whirlpool washer. Worse machine ever! It’s take forever to wash a load, there’s no way it’s efficient when it takes twice as long to wash one load. It doesn’t sense the water level correctly, Its noisy, and after only having it 3 years it crashed on me. I refuse to waste money fixing the piece of junk and when I go to purchase a new one it won’t be a Whirlpool.

In 2005, I purchased a Whirlpool front-loading automatic washer for $700 plus. The machine had to have repairs on it several times at my expense. Then in 2010, I had to replace it and spent another $700 plus on the same type of washing machine. Whirlpool would only discount $100 of the cost. The second machine three years later is now also needing repairs. I spent a total of over $1,400 in 7 years on two washing machines not including repairs and parts. It also took forever to find the parts, so I went without use of a washer for one month. I called customer service and said they couldnt do anything for me the second time around with them. I will never buy another Whirlpool ever! You would think a company would care about their customers but they dont. They make their stuff cheap and charge an outrageous price.

I bought my Whirlpool top loading washing machine 07-22-14. I so dislike the locking mechanism and will be certain to never, ever buy a machine with that feature again. It is so irritating to try to add something but cant because its locked so have to hold the button 3 seconds to unlock and start all over. If there was any way to get around it I would. I will stay away from Whirlpool products in the future and will be sure to check the next time I buy that the lid of the washer can be lifted when not spinning. Also, I do not like that it sticks on rinse sometimes and the only way to end a cycle is to hold the button and then start over with much wasted water.

Ive read a lot of reviews on here for Whirlpool Cabrio Washer and Dryer saying horrible things and maybe I lucked out? We got our set at Lowes a couple of years ago and havent had issues. We use Gain HE liquid detergent in the washer and have no problems. We also do the recommended routine cleanings of the machine as the manual says. I pick the settings for what we have, clothing wise, and it washes appropriately and things are clean, no marks or other things people have mentioned. I will click on extra rinse and adjust the soil level if something is particularly yucky. The dryer is great as well as long as you select the proper type of wash you have going on. I tend to do more dry setting and things never come out wrinkled. Sorry for all those who have had bad experiences. Also, others have complained about the noise...our old machine had an agitator and was very loud. Our machines are in a closed room and most of the time we dont hear a thing until the bell rings. Maybe wed hear more if they were in an open area or garage where noise echoes?

We purchased our home brand new in June 2010 and with it came all Whirlpool appliances. We started having cosmetic problems with our over the counter microwave about 2 years later (model WMH2175XVS-2). The plastic casing around the door handle started to crack on the top and the bottom and now both pieces are completely gone as they fell off. The handle is still attached and the microwave is usable; however, it looks shoddy. To replace it, we were told by a Whirlpool authorized repair person that you would have to replace the whole door at a cost of $300 or more if you include labor. I am disappointed that this happened and that we cant get it repaired. It makes me think again about purchasing more Whirlpool appliances.

I am a working single man. I needed a used washer. I shopped the new washers but they were a lotta money. I seen many of them were without agitators. Well heck... who am I to judge the progress in technology?? So, going around to the used appliance store I run across this Whirlpool Cabrio. OK, Whirlpool meant quality my entire life. So, I bought it. MASSIVE MISTAKE!!! This POS is no washing machine. I dont know what it is, but it is NO washing machine! It is a machine that runs a very few gallons of water into a load of clothes and makes them wet, and that is about it!!All I know is the federal government is dropping the ball on this situation BIG TIME!! To allow a company to foist off on consumers such a PILE OF JUNK!! The pile of crap is PURE junk as far as simply doing its job... washing clothes!! It is a DISGRACE of an American product, and I will NEVER buy anything made by Whirlpool the rest of my life!!I took the device off the lid that tells it when the lid is closed, and just stuck it in its receptacle in the body... so I could raise the lid while it is running and watch this POS in action and try and figure out what the hell is going on. First big problem is it NEEDS an agitator!! Obviously Whirlpool had not figured out how to make the clothes circulate without one. Second is the water level (no matter what cycle setting) is obscenely LOW!! The clothes do not circulate AT ALL, and about 1/3 of them do not even get below water level for the entire cycle!! What I am forced to do is use a water hose and run a lot more water off into the tub just to get the clothes in the damn water!! And ever at that, the clothes still do not circulate AT ALL!! They just rub up against each other!! And I have to use twice as much soap than called for!!

We purchased a Whirlpool hot water heater approximately 4-5 years ago and have had problems with the pilot staying lit. I contacted Whirlpool and their trouble shooting included doing a draft test (I am a teacher not a plumber) and removing the closet door that houses the unit. I am very frustrated by this entire ordeal and would like if they would replace the entire unit. At this point I dont want another Whirlpool product. The plumber made a service call at 12 noon and by 3:30 we had luke warm water and by 6:00 pm the water was ice cold! I will never recommend any Whirlpool products.

The refrigerator is about 2 years old. Has worked great. Stainless steel finish looks great. Was a good price at Lowes, with free delivery and removal of old refrigerator. I bought a simple model. Did not need a water connection.

I have a Whirlpool 33 inch wide Side by Side refrigerator. WRS311SDHM. This is the worst refrigerator I have ever had. Temperatures are inconsistent. It is less than a year old. Initially, I stored the big container of spring mix lettuce on the bottom shelf of the refrig as it wouldnt fit in the crisper draw. The temp setting in the refrigerator was set to ideal. Oddly though, in the freezer, ice cubes were melting and refreezing creating a massive frozen block. So, I raised the temperature in the refrigerator, but kept the freezer at coldest. However, I noticed that when I set the refrigerator to a warmer setting, ice cream became cold soup despite the coldest setting.I called Whirlpool and a service technician from Georges Appliance in New Providence, NJ came to my home (of course I had to take half a day off from work). He stuck a thermometer in the freezer and said, its working fine. While at my home he called Whirlpool who said that if lettuce isnt kept in the crisper drawer it will freeze (silly woman, dont you know that?) and ice cream will get soft in the freezer if the temp in the refridge is warmer than ideal. So, it seems I can have lettuce or ice cream, but not both. Okay, so I put the temp back to ideal, bought smaller packs of lettuce that would fit in the crisper draw and called it a day. Nope....lettuce and anything else in the crisper draw freezes too. Wilted, soggy lettuce is so nice in a salad and frozen baby carrots can break your teeth.I have been on the phone with Whirlpool executive dept several times. They offered to have another service company come out to look at the refrigerator. This repair company would not give me a 4 hr time frame until the day before the actual service call. This might be okay if you work from home or are retired, but this is not my case. I opted to not have them come. This is my last Whirlpool product. Since KitchenAid and Jenn Air are owned by Maytag/whirlpool, my other options are LG, Samsung, GE or Sub Zero.

Pilot light will not lit. I called Whirlpool. They said they could ship me a replacement for $34 or I could go to Lowes and get one for free. Lowes said they were out of type C kits and they have not received replacement kits for 6 months. Lowes informed me about the recall for this part. If its a defective part, Whirlpool should be sending this to me for free. I will not be buying a Whirlpool water heater next time.

Whirlpool fridge with ice and water dispenser that broke down within days of install. The water dispenser stopped working after the first flush and Whirlpool were notified. They engaged a useless repair company who have been unable to resolve the problem and will not communicate updates. Whirlpool have been fully informed of the problem with their brand new product which was defective practically from the start and have washed their hands of any involvement in resolving the problem with their appliance. They defer defective product as a warranty issue and leave the consumer to chase after people to get a repair done. For a brand new $3,700 fridge that doesnt work within a week of install I just cannot believe they would sell a defective item and make their consumer suffer for it.What consumer would knowingly choose to purchase a defective appliance? If you end up getting a defect, the company should make it right....right away. Im at 2 months now without a functioning water dispenser on a fridge that is only 2 months old. Just disgusting.

We purchased Whirlpool Gold Accubake, double ovens (gas) in 2005. Since then, we have experienced identical failures (8 to date) during the self-cleaning cycle in which the high temperature burns out the thermal fuse of the ovens. This requires two Sears technicians to repair the unit (it requires two technicians to pull the oven out as the fuse location is in the back of the unit) and leaves us without use of both ovens for approximately 2 weeks (scheduling parts delivery and technicians through Sears home repair is not an expedient process).After checking other consumer product websites, it has become clear to me that there is a known design defect with these ovens in which the thermal fuse is not adequately insulated from the high temperatures during self clean; it therefore trips and burns out during the self-clean cycle. While not having access to ovens for about two weeks/year on average may sound acceptable to Sears, the reality is that the problem has escalated in frequency since purchase. In 2013, we are going on our third repair of the same problem (that makes 6 weeks of non-usable oven time in one year) and Sears will not consider replacing the unit, despite: 1) our obvious dissatisfaction with a lemon unit, 2) a well documented history of the defect with this particular Whirlpool oven and 3) an ongoing and escalating repair cost to Sears (it is under their extended warranty so the repair cost is on them although we did pay for this service up front on our appliances).I would stay away from not only Whirlpool appliances but also Sears as there doesnt seem to be any regard for the customer experience and taking care of a product problem (the right way) with a known defect. Sears has an opportunity to make this problem go away quite easily and retain a customer - fix the problem permanently or just replace the defective unit. Unfortunately, my experience to date with Sears standing behind the products they sell provides me with little confidence that either will happen.

Bought the HE Whirlpool Cabrio in 2013 after having my old agitator Maytag for 19 years. After reading the other reviews I do not feel alone. An awful washer, a year after our purchase the spin cycle is so loud we have to close the laundry room door. Now it has been leaking into my basement. I called a repairman, explained my problem. He suggested to junk the washer, it will cost more to repair than buying a new washer. In addition my clothes did not clean properly, soap stains on clothes because it does not use enough water. This was about $1000 purchase that lasted less than 4 years! I am done with Whirlpool and suggest to anyone not purchase a HE washer, nothing like the old style agitator washers.

Your Whirlpool French Door model # WRF993F1FM is a piece of junk... Had the fridge less than a year and had to have repairman come and fix it twice already... Would never buy Whirlpool Product again. Builds up ice in the refrigerator and then loses of most of the food in it. Leaks the water right onto the kitchen floor...really pitiful to spend more than 2000 dollars for a fridge that is a piece of junk.

I purchased a Whirlpool 3 years ago. It was on the lower end for price so my expectations were not that high. It does an average job cleaning dishes so for the price I could give it 4/5. The pump and motor just went and had to be replaced. Almost the same cost as replacing the whole machine. The repair technician that did the work stated that this was a very common problem with Whirlpool in recent years. Of course this is not covered by warranty. So if you purchase a Whirlpool realize you are rolling the dice.

I have used Kenmore products for about 50 years, so when it came time to replace my old washer I looked at Kenmore/Whirlpool. I upgraded to the top of the line. I had been warned by 2 service techs (2 different companies) that had tried to keep my old Kenmore alive that the new ones are not up to par compared to the old ones. The first very small load that I tried, was not even thoroughly wet when I took it out to put in the dryer. 1st service call, tech suggested that I put machine on extra water.That helped sort of. A few weeks later, wash is not getting clean. Called Whirlpool, they suggested getting the washer cleaner and clean the washer. Went out and bought a special cleaner, $10-12 and two cleanings later using the extra water and extra wash water I now was getting cleaner clothes. They said I would need to clean the washer every 2 to 4 weeks. I have continued to use washer but frequently have to rewash about 1 in every 5 to 10 loads as it doesnt always clean everything in the load. Called the Co., they sent service out, they said its OK!In Jan. We went out of town for 2 weeks. The washer had not been used for 4 days before we left. Came home to water all over the floor which are hardwood. Needless to say our hardwood is all warped! Service came out, ran the washer for about 15 min. and said it was fine, nothing wrong! Called Whirlpool again! Washer is now out of warranty. They said call a local service, out of their hands as it is out of warranty! Nothing more than they can do.I have used Kenmore/Whirlpool Appliances all my life and they have been wonderful. The new ones are garbage as far as I can tell. I have a Refer that is now 3-4 years old and I have had problems with that, a new dishwasher that is 2ish and have had service out on that one, now my brand new washer top of the line and it is so bad I am afraid to use it unless I am sitting right in front of it watching it! Further if you have the rinse cycle on the clothes come out so wrinkled that you need to get out your iron out and iron everything including sheets and linens. Lucky that I did not replace my old dryer! Do I recommend Whirlpool anymore? Not on your life. I wish I knew what to replace them with!

I just bought a Whirlpool Cabrio Washer WTW8800YC1 yesterday (1/19/14) delivered today. First load never finished, kept getting error of F51, which I looked up and its a sensor. I looked up the review on this washer and it seems to be the census that this washer is POS. Im having the store pick it up and refunding my money. My old washer is 20 years old and never had an issue with it. We just wanted a more efficient washer. Thank Goodness I didnt have the store haul it away.

I bought a new washer thinking I was upgrading. Wrong!! Well the new so called technology they put into these machines is overrated. They took a good thing and instead of advancing they have took two step backwards in time. I wish I had kept the old washer I had. I think I would rather use an old time wringer washer my great grandmother used. They are probably faster by hand. This new Whirlpool grabs every string on my hoodies and twist my clothes so tight in knots. I cant even remove my clothes until I fight and get mad enough to write a review. Whats up with these new washers?? Get rid of the slots on the Agitator!!

Whirlpool refrigerator - I purchased $6950.93 in Whirlpool products in one day last year at HH GREGG in Lexington, Ky. The refrigerator was purchased on that day September 18, 2012 and my kitchen wasnt going to be ready until December, but I wanted all items bought for measurements (specs) for the new kitchen designer. HH GREGG delivered to my garage October 26, 2012 because they couldnt hold any longer, but when we purchased that day they promised to hold till December when my kitchen would be finished. I have Proof from the kitchen installers the day they finished, December 28, 2012, was the day the appliances were installed. Well here I sit typing this letter on January 7, 2014 and my Whirlpool refrigerator is as of right now is in need of a compressor while losing approx $1000.00 in purchased food. In other words, approximately $900.00 in repair cost. Isnt Whirlpool a large enough company to stand behind its products when I paid $2599.00 for this refrigerator for at least one year from installation instead of purchase date? My fiancee has been trying to work out a solution with Whirlpool and the parts are on back order now. For at least two weeks we have been without a refrigerator and have two young children. Doesnt it show that the parts being on back order from Whirlpool, barely being a year old prove the defective product is being sold to the public daily? I plan on going further with this action due to the name Whirlpool all over my kitchen which disgusts me. Im going to write every columnist I can and do all I can with what little resources I have against this large company if no one helps us. This is absolutely an injustice against consumers...

I purchased my Whirlpool French Door Gold Series fridge for $2179.00 in November of 2013. We just had moved into a new house and wanted a fridge that would last a long time. In the past couple weeks the freezer has stopped freezing and after calling Whirlpool I was told I was out of luck and would have to pay full retail price to get the problem fixed. This will be the last Whirlpool product I ever buy.

Cleans dishes very well, a bit noisy maybe that just the model I have. Exterior is very nice, interior there is plenty of space for the dishes and pans. There are no streaks on the glasses. No soap scum left on the dishes at all, very good unit.

I purchased a new park model house with Whirlpool appliances. The fridge door is crooked in 2 directions. It is only adjustable in 1 directions. Top to bottom. After 5 months of trying to deal with whirlpool and being told my warranty is void because of adjusting the door according to their manual. They also tell me that warranty will not cover factory flaws which the crooked door obviously is. Whirlpool will never darken my door again except on the way out. Whirlpool sucks!

We purchased our side by side refrigerator from Lowes. When it was delivered, we noticed the freezer door was rubbing on the ice maker and would not close properly. The refrigerator was replaced. Then about 10 months later, the water dispenser stopped working. Service came out and said the water line had ice in it (we do not keep the freezer on high). They replaced the water line in the door. About 6 months later, after the unit was out of warranty, the same thing happened. We called Whirlpool and they said there was nothing they could do, because the unit was out of warranty. I cleaned out the water line tubing myself and the unit worked again, but the problem occurred again several months later and it does not seem right that the water dispenser line should keep freezing up. In addition, every two months we have to take the ice maker apart because the ice will no longer dispense because of an ice buildup in the ice cube container. We used to think that Whirlpool made reliable products, but with these problems and Whirlpools unwillingness to correct the problem, we will never buy their products again. They have lost a long time customer because of their products now and their customer support.

I bought refrigerator in Feb 2017. Within 18 months internal surface got crack, contacted customer care but I would say Whirlpool India customer care department is worst across world, no courtesy towards customers, contacted them over phone very bad attitude, no response on email. Product quality is worst, its better to buy Indian brands. They are much better in quality & service. Totally dissatisfied with Whirlpool approach, at the end Whirlpool customer care is not at all bothered.

The features on the washer is a wider size wash basket, no non-snag agitator with 5 load size choices, 5 water temperature choices, type of wash includes soak, quick wash, normal, deep water, heavy duty, bulky, hand wash, gentle, some other choices Along with a choice to wash your machine, one rinse or two rinses without fabric softener, one rinse or two rinses with fabric softener. And finally a selection for Pre-soak on or off. Also has a 3 light display for what it’s doing, lid lock, pause, cancel and start button. It’s an HE. Clothes come clean.

I purchased a Whirlpool washer and dryer from Best Buy. I purchased one on sale that was a great value. The delivery and set-up went well. However, the model I have had a loud vibrate. The drum in the washing machine would wobble and shake across the floor. I finally had to return it and replaced with same model. I experienced the same issue after 30 days. I didnt take the insurance out and I regret that move.

If you are in the market for a new refrigerator, STAY AWAY from Whirlpool Top Freezer models. Mine just failed after only 5 years and Whirlpool will NOT do a thing about it, except ask, Did you buy the extended warranty? The compressor in my refrig was made in Mexico by a company called Embraco. I used to work for Whirlpool and these compressors were garbage then, and I guess still are, in my opinion.The 5 year sealed system warranty was removed from these refrig years ago and I can only assume this is why. If you want the 5 year SS warranty, buy a side by side or French door model. Just be sure it doesnt have an Embraco compressor on it! And while I am not a believer in them, planned obsolescence dictates you probably should buy the extended warranty/service plan for such a purchase. Dont rely on positive past experience, even for a company like Whirlpool. Their gold ring of promise emblem is very tarnished for me now.

We purchased a Whirlpool Gas Water Heater (Model No. N40T61-343) from Lowes in the Summer of 2013. 2.5 years later, the water heater goes out as of 01/19/2016. Therefore, I contacted the telephone number on the side of the water heater in order to restart the water heater. We followed the instructions by pushing in the pilot button, as well the ignition button. To no avail, the water heater did not restart. I called customer service on Thursday (01/21/2016) to speak with a representative. She said that we needed another Thermopile and a Gas Valve replacement. So, who is going to put it on? It would cost as much as getting a whole new water heater. Therefore, we are going to Menards to purchase the Richmond Gas Water Heater. We had a Richmond once before; and it lasted from 1999 or 2000, until 2013.After reading all the reviews about this brand water heater (Whirlpool), no wonder people are complaining. Ladies and gentlemen, do yourselves a favor and not buy a Whirlpool Water Heater. The only thing that Whirlpool is good for is only their name. Their Water Heaters in particular are worthless pieces of junk. NEVER BUY A WHIRLPOOL GAS WATER HEATER AGAIN!!!

I bought a Whirlpool Partner II 5 and a half years ago. It was always noisy and took very long to run a cycle. It started to malfunction after 2 years. We bought a new computer for it and a new control panel for the touch keys. It still kept not running a cycle fully. We found a YOUTUBE video that showed how to reset the model by pressing a combination of Normal and Heated Dry and that seemed to fix it for 2 years.It has stopped working again. Now it seems that the heating element is out. It doesnt clean at all, a scum film has covered the inside of the dishwasher and even mold spots are appearing. Ive had to wait extremely long times on hold to talk with an agent. My option is to hire a repair tech to come out and repair it and I pay for the parts. Seems like a bad deal since Ive already spent over a hundred on repairing it and a lot of hours. I will never buy a Whirlpool brand appliance again.

I was harassed and tortured. I got an extended warranty on Whirlpool microwave oven but from the last six months, I was not able to use it. The original part worked for four years but from the last four months, engineers have tried to change the part and it was a duplicate one every time. It did not last for 15 minutes in front of the engineer. To date, the engineers are still not able to fix my oven so I havent been able to use it for the last four months. Does it mean that Whirlpool make duplicate parts too and just ditch the customer? Is this also included under Whirlpools code of ethics?

Two years ago, we purchased a Whirlpool Cabrio Washing Machine from Sears. All of a sudden, it was making sounds in the spin cycle that sounded like a jet airplane taking off. It was terribly loud. We called repair technician, which cost $90, only to find out that the bearing is gone and its going to cost over $500 to fix it. This is absolutely ridiculous! We expected it to last several years, only to find out that we would have to spend almost as much as the washer originally cost in order to fix it. We paid $700 for this machine, two years ago, and I can say that Ive never been more disappointed with a product in my life. My previous washer lasted thirteen years, not to mention my dryer and stove fifteen years, with minimal repairs. I will never buy another Whirlpool appliance again. I have read some other complaints on this consumer affairs website, as well as other sites, regarding this same washer with the same problem on the bearing and cost to repair. If anything, I think Whirlpool should make good on this product and offer something regarding a recall or payment for repair in some form. As far as Im concerned, I will alert everyone I know about Whirlpool appliances and advise them not to purchase it. Now, I either have to pay over $500 to repair my washer or go buy another one. I do not even want this Whirlpool appliance in my house when I can get a washer for cheaper than the cost to repair it.

Whirlpool Duet WFW94HEAW0 Washer - Bought the machine in Feb 2014 and was generally very pleased with it. However a few weeks ago we started getting oil/grease stains on clothing. Wasnt sure what was causing it but it has now got so bad that the machine cant be used. An internet search indicates it is possibly a ball racer ring and doesnt sound an uncommon issue. A call to Whirlpool resulted in a quote for circa $350 for a service call. Thats a 1/3rd of the original value (includes a 12 month warranty). And its just over a year old!!! We had a problem with the Maytag Neptune that ended in a class action suit and now this replacement machine seems to be even worse. I would recommend anyone to really consider what to buy and give this range a miss.

Washer MOD WTW4800XQ2 - I purchased this washer about 2 years ago after my 15 year old washer died. I have always used Whirlpool appliances as well as my Mother that recommended Whirlpool to me some 40 years ago. I knew when this machine was delivered and set up that I was in for change. It locks down to where you cant get in it for too long of a period of time. I am a really busy person, and HATE this, but if that were the only issue, I could accept that. We live on a farm and our clothes get really soiled especially in the warmer months. I like to pre-soak white clothes, NOT happening with this machine!!! It ends the cycle after about 30 minutes so I have to start over, wasting water. But the main issue is the machine tries to level the clothes, or whatever it is doing on its own before filling with water. I wash a lot of clothes!!! I am going to say that 90% of the loads of clothes that I have washed with this machine have been off balance, banging around bad. I then have to wait for it to unlock so that I can pull out the dripping wet clothes and replace to try and get it balanced. I am 59 years old, I got married at 14. So Ive been washing clothes for a LONG time... This machine is junk to say the least. I recently house sat for family. They purchased a new GE washer and dryer a little bit before I got these, wonderful machines!!! I washed dog beds, sheets, blankets and tons of clothes during this time. WOW, I had forgot that washing clothes didnt have to be torture. I will NEVER purchase another Whirlpool product. This washer has exhausted me. I purchased it at Lowes on tunnel rd in Asheville, NC. Please, if you havent already, junk this design... Its gonna lose your loyal customers. This complaint has nothing to do with where I purchased it. I did not contact the store as they did not design the machine. I did NOT want to pay for service on a poorly designed product...

I bought the top-of-the-line Whirlpool top-loading washer and havent regretted it for a minute. This machine washes everything from the most delicate to the most bulky and heavy and does an excellent job of it. It saves about 1/3 of the water my rotary agitator washer used. What more could I ask from a washer. Incidentally, also purchased the largest front-loading electric dryer Whirlpool makes and never have to hold a load of wash until the dryer finishes the last load...a real time-saver.

Surprised my daughter with a Whirlpool washer and dryer computerized, never again you have to stand at the washer half the time resetting it over and over. It takes all day to wash. Went to Lowes. They said yes you have to start it three times. What a pain. Never will buy one again.

We bought a Whirlpool Cabrio 2 years ago and they are an absolute piece of junk!!! There is only 2 people in our family so its not like we are washing big loads. It doesnt get my clothes clean and the clothes stink. I have followed the directions on cleaning the washer and it does not good. Now my clothes are soaking wet at the end of the cycle so I have to put it on drain and spin just to get most (not all) the water out of them. And when I take my clothes out, they are just as dirty as when I put them in. Called a technician and its going to cost over $400.00 to fix. This is nothing short of robbery!!!! This machine is a piece of junk. I read over 500 reviews on this washer and they all had problems that cost as almost as much as the washer cost to repair. There really needs to be a recall or a class action lawsuit against Whirlpool.

The dishwasher is less than 2 years old, out of warranty, and will not start. The repairman said the problem is in the electronics. It would cost $500+ to repair.

Whirlpool washer is junk. Expired I. Less than 4 years. Cost to repair is more than new washer. DO NOT PURCHASE WHIRLPOOL PRODUCTS. Agitator motor burned up without notice. No troubleshooter problem. 2 repairmen suggested I buy new washer.

Purchased on 9/12 at Home Depot. Ice maker paid for as stated in ad for home depot, did not come with fridge. Tech needed for warm food, had to repair gasket. Tech needed for cracked handle. 6 calls for freezing food in fridge compartment. No resolve. Whirlpool wanted a 2nd opinion and another tech came deeming the fridge unrepairable. Not good enough for Whirlpool. After speaking to several customer service agents, they said they do not refund or replace, only repair. I have lost hundreds of dollars of food from freezing. My fridge is reading at 31 deg. This is way below what it is supposed to read at. No call from Whirlpool since last tech came. Their customer service is terrible and cold. Whirlpool Corp. was not any help either. You can see the problem with this model if you look up Whirlpool fridge freezing food in Florida, as a woman there called ABC news and they reported it. I will also do the same.

We have a Whirlpool Quiet Wash Plus dishwasher thats been doing a great job cleaning our dishes for just shy of 24 years. We use a cleaner every 2-3 months to keep everything cleaned out and sanitized. We use a liquid detergent and a rinse aid and the dishes come out clean every time. We feel like weve been blessed with this machine and would definitely buy Whirlpool again.

My dishwasher quit drying and washing in hot water at Thanksgiving 2021. I could not get someone to look at it because the repair company (for Whirlpool) could not get to it until January 2022. The repair tech said it was it could be three different things. He was going to order all three parts. Three weeks later, they came to repair it. It still didn’t work and I hate to wait two different days (all day) for service. First day, he didn’t make it so had to schedule for next week. He replaced the other two parts. It now works by still doesn’t dry like it should. Not thrilled with performance at all!

I replaced my 12 year old Whirlpool double ovens with the current Whirlpool double ovens. The new 30 built in double ovens have been re-designed to vent the heat below the lower oven. The ovens come with a part that pushes the heat down instead of straight out. My built in ovens have a cabinet drawer below and after using the ovens just 4 times over the holidays I noticed the heat is damaging the finish. According to Whirlpools service center I should have checked on that before buying/installing. They told me to stop using my ovens, that this is a fire hazard, but they are not responsible. They do not have a solution to this problem. This is a poor design on their part. There is a disclaimer in their installation booklet that came packed with the ovens that the installer gave me. It says the cabinets need to be able to withstand the heat of the ovens. The cabinets can handle the heat of the ovens, just not the hot air venting directly onto the cabinets below the oven. Where does one find cabinets that can withstand 400 degree heat being pushed directly onto them? As a customer I did not have that information until after the ovens were installed and it was too late to purchase another brand.

I bought new hot water heater. I installed it did and it did not work. I called them, and they sent a new part. A service man installed it, and it still did not work - he was unable to get it working. They said my gas supply line 1/2 od was too small. I had it replaced to 5/8 od 1/2id, and it still did not work. I called them again. They offered to send more parts and try again. This is a brand new water heater, never fired. I asked if they would give me a ra number so I could return it to the store. He would not give it to me. He insisted he send some one out to try to repair it. Meanwhile I have had no hot water for 2 days. He told me do what I have to do and hung up on me. So I removed the heater and took it back to Lowes, where they were glad to give my money back. But still, I lost a day of work and paid the gas yo bring it back. I went to home depot bought a GE hot water heater. I had it installed in about 15 minutes and it is working fine.

The machine has an infinite water level setting, an agitator which I feel cleans clothes better, separate settings for water temperature for both wash and rinse cycles, and the ability to soak prior to washing by just leaving the lid up. You can add bleach and fabric softener to dispensers that will add to the tub at the time needed. My machine has been a really good one.

Whirlpool French Door 32 Cu. Refrigerator - Purchased refrigerator Nov 2016. Never worked, never cooled. Called Sears and was told to call Whirpool. Had to then wait 1 week for repair company to send out service tech. He determined it was unrepairable. A replacement was delivered. The replacement started flooding the interior down the back, filling underneath the bottom drawer and down into the freezer (ruining everything in the freezer) and out onto the floor. Called Whirlpool and had to wait another week for a tech. They assessed the problem and left. I was told it would be fixed within the week, that theyd call when the parts arrived. 3 weeks later, no word. Called Whirlpool, the parts were on backorder with no ETA. Two weeks later the parts were expedited, after I called again crying, and a tech came out again to fix the flooding. Two weeks ago the fan started to make a very loud noise and the internal temperature started to fluctuate and finally settled between 55-60+. Everything was ruined, again. This refrigerator is defective. Whirlpools customer service is deplorable. DO NOT BUY ANYTHING FROM WHIRLPOOL!!! They dont care that they make and sell defective crap. They dont care about how much money and time youve lost because of their defective merchandise. You have to have a service repair person come out at least 3 times before theyll even consider a replacement unless the repair tech considers it unrepairable even if it never really works or if the parts take weeks to be delivered. They DONT CARE about anything. Worst part is that I have no power or recourse. No one will help me. I was told today by the Sears Customer Relations to hire a lawyer. :( This is so wrong.

I am concerned that Whirlpool microwaves installed over the stove have extremely faulty doors. I have two homes in which I have Whirlpool microwaves, and both have huge cracks in the door and small pieces inside the doors beginning to fall out. It deeply concerns me that it will cost more to replace the doors than to replace the microwaves. I have always believed in Whirlpool appliances but now feel that I will have to change brands. My question is “What in the world is wrong with your doors that they crack so easily and the company holds no responsibility with such faulty work?” I would simply think that this was just a faulty door on my microwave, but I have two that are cracked! This definitely means you have a faulty product.

In April of 2016 I purchased an aqua clean self cleaning oven from Colders Furniture in West Allis Wisconsin. We were told by the sales associate that the oven was top of the line. This was a complete and utter bold face lie. I cleaned the oven for the first time the day after Christmas after having prime rib. I followed the instructions to a T on how to clean the oven. I had to turn the oven on 6 times and scrubbed the oven until my fingers were bleeding, not to mention the enamel on the inside of the oven is completely bubbling. I called the customer care center on December 31, 2016 and the representative basically said I was an idiot and did not know how to cook. They made an appointment to send a technician out on 1-5-2017. Before hanging up the phone the technician informed me that if there was nothing wrong with it that I would have to pay for the call. At this time I became irate and refused telling them that I have not even had the stove for 8 months and that it was still covered under extended warranty. I will see what kind of smoke is blown up my rear end. The technician is sending a new sponge and scraping stick. How about someone to also clean this piece of garbage. My advice is to anyone is if anyone tells you to buy an Aquaclean self clean oven from Whirlpool run in the other direction and do not buy it. Thanks Whirlpool for the garbage and for sending me cleaning products that are not even worth a damn.

Whirlpool Duet Machines - I feel very fortunate as I have not had a single problem whatsoever with my Whirlpool washer and dryer and it is 5 years old. Never once have I needed a part or had trouble with it. I feel bad for those of you who are dealing with this as what is worse than a washer/dryer that does not work?

When I bought my new retirement home, a Whirlpool dishwasher Model No. DU1055XTVS1 had been installed. After only three years of use, the dishwasher would not complete a cycle except to drain and cancel. The repairman replaced a computer board and when the parts cost and the service cost were combined, they amounted to about half the cost of the dishwasher. I have a PC that is twice the age of the dishwasher and it is still running.

I purchased the Whirlpool Cabrio Top Load Washer in 2009. It stopped working and I found that it needs a new control panel and recirculating pump which will cost $390, including labor (plus the cost of the service call to diagnose the problem). I would not have expected to have this type of problem with a washer within 3 years of purchase. I cannot recommend this machine.

Dont buy their produce!!! My refrigerators bought in January 2017 and just use 9 months. It breaks and repairs 3 months. It cannot repair and Whirlpool will refund for me, but I wait long time and no any answer. I try to call Whirlpool customer service. Their staff hold me long time and tell me they will be call back... Oh my God!!! I left my refrigerators 3 months ago. Whirlpool did not care the customer. Terrible company!!!

I purchased a front loader Whirlpool Cabrio washer/dryer in June of 2011. I was sold an extended warranty which ends June 30 of this year. I have made 4 calls to the Co which warranties the washer because it is making squeaking noises on the spin cycle. I was refused service because the customer service rep didnt “hear” anything. I finally had a local service Co check out the machine and was told the motor needs to be replaced and if under warranty I should demand it be replaced. I called again and still cannot get NSI to come out and see the problem.

I had my entire kitchen re-modeled in May of 2013 and purchase all new Whirlpool appliances. I work for Standard Pacific Homes and purchase the identical appliances we provide in our homes. I am so disappointed in the refrigerator. Two months ago it stopped making ice and I was told to replace the filter and it would be OK. I did that and still no ice. I bought ice trays. A couple of days ago, I came home to find water on my kitchen floor coming from under the refrigerator. I called Whirlpool again and no real help.... Told me to call Lowes. I called Lowes and they gave me 3 more numbers to call for service. None of those service providers had any available appointments and told me to call Whirlpool. Meanwhile my refrigerator is standing in the middle of my kitchen so I can keep the water mopped up. The refrigerator was so difficult to move. Getting the feet moved up so the wheels could touch the floor took an hour and I ended up with bruised hands. My lesson in this is to buy a better brand next time and go top of the line. I sell these to our buyers at Standard Pacific Homes everyday..... Wish I could believe in the product.