Whirlpool Cabrio Top Load Washer Model: WTW7800XWO purchased at Lowes 8/26/2010. The lid was broken at the hinge in less than a year and was replaced under factory warranty. Lid falls down and pinches fingers. The second lid broke in the same location in less than a year. Lid falls down and strikes the eye. I’m speaking with repair technicians and researching complaints on this product. It appears to be a design defect that is not being addressed by the manufacturer.

Whirlpool Clothes Washer Model WTW4930XW1 - We have experienced tub overfilling on (2) separate occasions with this washer model in a period of time of less than (2) years. Through extended warranty service purchased, a technician came out the first time; declared nothing explainable to cause the malfunction, re-calibrated the control panel, and off he went. This second event occurred much the same as the first; happened to walk in to notice water on laundry room floor and witnessed overflow out the lid on top. We have carefully washed additional loads after this second event without a similar malfunction. From my online research, this sure sounds like a faulty pressure switch not sensing high water level in the tub. Any other thoughts?

I had a perfectly good Kenmore range, but I didnt like the color. I purchased a Whirlpool 30-inch gas range at Lowes. I had problems immediately! The repairmen were at my house 6 times within the first year. My warranty expired and they wanted me to pay for an extended warranty. I refused to pay any more for this piece of junk! I fought with Whirlpool and demanded they either replace the range or reimburse me the full cost. They finally agreed, after many heated conversations, to replace or reimburse me as long as I promised not to purchase a Whirlpool product again. What kind of company would say that? A company that knows their product is defective and has poor customer service. I opted to take the new range that they promised wouldnt have the same problems. It is having the same issues as the original one. It shuts off in the middle of cooking and it is infuriating to say the least. I can promise Whirlpool I will never purchase a product from them ever again!

I had water heater EE3Z50RD0550V installed on 11/3/11 and it started leaking July 29, 2013. Whirlpool gave me Return authorization # and said I have to return the water heater to Lowes (purchase place and original installer) to get a new one. Fortunately, Lowes said I only have to bring them the RA # and they will swap out the water heater. However, there is a $300 charge for installation. Whirlpool says they only cover this the 1st year, except when its a manufacturer defect. But they cant tell me how to prove its a manufacturer defect. Why else would a glass lined water heater start leaking only 21 months after installation?

Multiple issues with this two-year-old refrigerator. Do not buy! The exterior stainless steel doors rust in sporadic locations. According to a quick google search, it is a widely known issue that Whirlpool has not addressed. We have never used abrasive cleaners, only wipes that are made for stainless appliances. We use them on all of our stainless appliances. The fridge is the only one that now has 10+ areas of pitting rust. It continues to spread! What the heck?Secondly, the ice maker stopped working at 16 months. First it was just the auger that stopped turning. Which was inconvenient but not the end of the world. It still produced ice, but we had to open the door and pull ice out instead of having it dispensed. Now it has stopped producing ice altogether. We had the repair guy out today. Apparently, the motor for the auger and the actual ice maker are not receiving power any longer. The certified tech said it was either the main control board or bad wiring somewhere from the control board to the ice maker.For a small fortune, we can try putting in a new board. If the new board doesnt work, we will then know it is a wiring issue. If it is a wiring issue, we will have paid for a new board that was not needed, and we are out of luck completely on the wiring issue. Part of the wiring is sealed within the freezer door. A new freezer door costs nearly as much as the fridge. Part of the wiring is sealed in the back of the fridge. It is impossible to open the seal without breaking the fridge, because the back is a sealed system. But it does keep our food cold. Just dont put anything the top shelf of the fridge because it will freeze. Thanks for the 1 year warranty Whirlpool! You timed it perfectly! What a joke.

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

I can add my experience with the many others I have read about. My Whirlpool Cabrio washer top lid glass broke in the up right corner after only 2 months use. Like many other reports, this is not due to something falling onto the lid. It happens without warning and without operator interaction. This is a defective design!

The Whirlpool fridge we bought kept freezing food in the fridge. Local technicians couldnt solve the problem after replacing some parts. They called Whirlpools technical person and found there are other similar cases for this model. We were told to wait till they solve the engineering issue. We require to replace another model. Whirlpools customer service Supervisor whose name is Alisha talked very arrogantly and hung up on us. In one word, bad products, bad service, bad people. We will stay away from any Whirlpool product in the future.

Since my review I have been corresponding with Whirlpool Customer Service (Chris). First he sent me an email and mailed a replacement board to have us (the homeowner) install. Because the cover was so melted, the replacement board would not fit down into it. I emailed pictures to Chris. Once he saw the pictures, he called me and arranged for the water heater to be replaced since it was still under warranty. He even extended the authorization code so we would have plenty of time to arrange for a plumber to do the work. We had to pay for the plumber, but Whirlpool arranged for us to have a new water heater. Now I can sleep at night without worrying that my house would burn down if the old water heater caught fire. Chris was GREAT to work with. I had a direct number to him and called any time I had a question. I was very impressed with Whirlpools Customer Service.

Whirlpool 5.3 Cabrio. This was the worst experience ever with a washing machine. My first cabrio did not work at all. My second one gave out after 2 weeks. It would not spin. I got my money back and would not recommend this washer.

In January 2011, we bought several appliances and a refrigerator was one of them. The model number is G15VAXVQ01 which is a side by side, French Door Ref with water and ice on outside. We have had problems with the very cheap plastic drawers that are at the bottom of the refrigerator to hold vegetables and meat. We have to be extremely careful so they will not break when opening the drawers. As of late, the fruit and vegetables have been freezing. I went to change the temperature on the outside gauge and dropped the control to 33 degrees and it stuck there. I tried to unplug the refrigerator to reboot the system, to no avail. The temperature is stuck at 33 degrees which will freeze most of our food in a few hours. The freezer side temperature gauge does work.We also have problems with the ice/water machine. I pushed the water button a week ago and from then on, I couldnt get the ice to come on. I did unplug the refrigerator to reboot and then I was able to switch over to the ice, but I could not get back to the water side. Also, there is no crusher on this machine so the ice comes out in chunks. If we had to do over again, we would not buy a Whirlpool as it appears that they are not interested anymore in quality products and consider cheap junk something to be desired. Not by us! We will get this albatross fixed and see about getting rid of it. It is a buyer beware market so I suggest others beware of Whirlpool products.

I bought a Whirlpool Gold refrigerator in 2010 from Lowes. Within months it had a Freon leak and Lowes had to replace it. I had bought the extended warranty. In 2011 a part had to be replaced twice due to excessive noise. Then the freezer got frost buildup on a coil in 2012 and again in 2014. I called Whirlpool and asked if they would pay for my next 3 year warranty. They said no, it was my responsibility after the first year. I would never buy a Whirlpool product . Do research, Whirlpool makes several brands.

Its supposed to be energy efficient yet it takes AT LEAST two times as long to get one load done, regardless of size or cycle preference! Now laundry takes all day! Literally! And why is there a lid lockout? Did someone accidentally fall in? If I drop something after Ive pushed start, I have to wait until the machine unlocks the lid. Why? This seems counterproductive. Its a top loader!

Im so disappointed with this product. Its only a couple of years old, which seems fairly new as my old washer was over 20 years old when I finally got rid of it because of the noise it was making! First, the Cabrio stopped draining and spinning, even though the display showed that the cycle was done. Phoned Whirlpool, and the best they could do was send out a repairman - at our cost, of course! We refused, and kept using the machine - put it on for an extra drain and spin. Then, it stopped working completely! My husband hauled it out to a repair shop and was told it needs a new motherboard at a cost of $400 plus labor! This was an expensive washing machine, and I feel Whirlpool should offer its customers better service! I guess we need to buy a new machine - definitely not Whirlpool!!

I bought a refrigerator from Lowe’s and the refrigerator had a lot of manufacturing defects. I called Whirlpool and 3 techs were sent to my house. After the last tech, Whirlpool decided to exchange the refrigerator. Since then, Whirlpool has been playing games with me.

The Whirlpool microwave has been very reliable and efficient. I like its multiple functions, from heating up leftovers to defrosting meat and poultry, baking potatoes. All the functions are easy to use.

I bought Whirlpool water heater model #FG1H5040T3NOV about 5 years ago. Burner assembly was replaced two years ago and now, thermocouple was replaced yesterday.

I bought a 5 burner Whirlpool range that I really like except the danger of knobs turning on too easily and releasing gas. You just have to brush up against them lightly and they turn. 3 times my nephew has come into a gas smelling kitchen. Whirlpool sent repairman out. He said they operate properly. Really?? What to do?? Does someone have to die?

I have a kitchen collection of Whirlpool products, not even 2 1/2 years old. I have had nothing but issues. Microwave was completely rebuilt within few months, refrigerator and freezer multiple issues. Latest is the freezer stopped working, now my good is ruined!!! Wont always make ice in the icemaker. Already had to replace freezer door because it was warped and the seal didnt work and now my dishwasher isnt working!!! **!!! I waited 20 years for a new kitchen, finally got one and did extensive research thinking I was safe with whirlpool. I was wrong. So now what, what happens when the warranty runs out, Im screwed. Shame on you whirlpool for putting out crappy products and doing NOTHING to try and fix this!!

We purchased our new Whirlpool Cabrio washer on November 1, 2013. From the start this machines performance has been a disappointment. We bought the machine at The Brick (I should have known better) where we had made several purchases over the years ( I guess Im a slow learner). Right off the hop, my wife and I noticed that the clothes were not coming out clean. Even though the machine is Eco and therefore advertises that it uses less water, there should be enough water that the clothes at least get evenly wet. That may be a problem with the agitator not seeming to have the guts required to pull the clothing down to the bottom of the drum. We went back to The Brick and told them that we were not happy with the machine they had sold us and quite predictably they told us that we should call Whirlpool (This was less than a week after we had it delivered. Did I mention that I may be a slow learner?). We called Whirlpool and they told us they would have a tech out to take a look at it on November 11th. Wow, I thought. Hows that for service. A repair guy coming out on a statutory holiday. Of course it didnt happen. When we called them back to ask if their repair guy had made it home okay, they claimed that we werent there when the repairman tried to call to confirm his arrival time at our home. We hadnt left the nest the entire day. They then told us to go back to The Brick. We went back once again and told them, yet again, that we were not satisfied. This time they agreed to send their own man over to take a look. He came over yesterday and watched the machine go through an entire wash cycle and then said that there really wasnt anything he could do, as even though it may do a crappy job of washing the clothes, it at least appeared that mechanically speaking there didnt seem to be anything wrong with it. We called Whirlpool back today and they said that there isnt anything wrong with it mechanically so from their end, at least, the story is over. What kind of customer service is that????? Maybe Whirlpool and The Brick deserve each other, but I think we should get better treatment than that

Ive got a brand new house, with brand new appliances by Whirlpool. Within less than 6 months, my dishwasher, Model no. DU1015XTXB0 Serial no. F00702058, had its electronic board gone bad. Instead of replacing the dishwasher, Whirlpool replaced the part. Not even one year later the same part went bad. Now, the dishwasher is not even 18 months old and it will cost $255.00 to repair. It is just the two of us in our home and I bought Cascade packets 20ct x 5 at Sams. Im not even done with the packets, so I know 100% that we have run the dishwasher just 70 cycles in 18 months.

Over-the-range microwave hood combo - It is not that it does not work, it just wont shut off! Close the door, it turns on. Touch the side, it turns on. I have walked in the kitchen and found it on! I am afraid it will turn on when I am not home and burn down my house! After reading the poor customer service received by others, I will just replace it.

I purchased a Whirlpool range YGY399LXUQ in 2012 from a great local appliance store, Trail Appliances. In 2013 the control panel stopped working and I contacted Trail. They quickly came out and replaced the control panel. In 2014 the same issue came up, but Trail could and would not do anything so I contacted Whirlpool Directly - they came out and replaced the control panel. In 2015 (same month) the control panel is not working AGAIN and Whirlpool has washed their hands of it. A replacement is over $400 + installation. The stove is barely worth that much. I would have thought that they would stand behind their product, in that this is an obvious continual issue or at the very least the service that they provide. I would not recommend their ranges to anyone because they will not stand behind what they product nor will I ever purchase anything that Whirlpool makes as it is obviously low quality.

I bought a Whirlpool fridge in June of 2014 and the plastic part of the stainless steel handle that attaches it to the fridge broke about a month or so later. After replacing the fridge because the company said they no longer made the part they gave me a new fridge and with that one the door would not close without leaving a gap of about 1/3rd of an inch open at the hinge side. They took that fridge back and sent me a new fridge. A week later I got in the mail a handle for the first fridge which I no longer had. About a week after that I noticed that the latest and third fridges handle had a crack in the same place. Whirlpool sent me 5 replacement parts and they were all defective with the same crack visible in the replacements. Finally I got a replacement handle that looked good and it broke today, Feb 6th 2016, in the same place as the first one. I should mention that each time the company replaced the fridge it was with a different and better model and each with a slightly different handle. There are other design flaws with the fridge. The door is in a corner and there are cabinets on the wall so the door can only open slightly more than 90 degrees which makes it impossible to open the crisper drawer enough to get a cabbage in it and if I want to clean the crisper drawer I must move and turn the fridge in the kitchen. Also if the crisper drawer is not closed completely it causes the guard rail on the bottom door shelf to fly off sending everything on the bottom shelf to fall to the floor. Fun when some are made of glass and filled with liquid. You would think I would have learned my lesson about this company but no! I went to Lowes and bought a Whirlpool dishwasher and when I saw that the automatic door would not open enough to dispense the soap, powder or packet I called a certified Whirlpool repairman who told me after receiving a duplicate that of course would not work either, that there was no solution to the problem and I went back to Lowes and bought a Samsung and my problems were solved. I WILL NEVER BUY ANOTHER Whirlpool or as I now call it, Whirledpoo, product, EVER.

Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

Four months after purchasing an $1,800 stainless French door fridge it began to not cool even though it was running. I called and was on hold for 45 minutes, then transferred to a different service company that could only come 3 days later. They were here a total of 3 times and each time they could not fix it. It would run for a few days or weeks then die again. Each time I lost a few hundred dollars in food. Each time I was on the phone for almost an hour, and each time it was days later before they would come. Whirlpool refused to refund or swap out the unit. I would have been stuck if it were not for Home Depot finally agreeing to exchange it for an LG.I have never been so upset with any companies customer service in my 45 yrs. The only reason that I am writing this is because my Sony 65 TV died the other day. It was 6 months old and I called Sony. They answered within four minutes and quickly decided to exchange it for a new one and extend my warranty for 2 additional years. There are still decent companies out there. I will never buy another Whirlpool product again.

I would not recommend this product at all, nor would I recommend the Whirlpool Company. This washer was over $1200.00. Within two weeks of purchase, I had to call a service repair company as I was immediately having issues with the washer not draining. Being a front loader, this machine required using the appropriate HE detergent. I followed the instructions, used the appropriate products and had nothing but continuous problems. It is a (lemon), and very frustrating, as it does not seem repairable. No serviceman could give an appropriate reason as to why the washer would not drain, nor could they figure out why. It didnt matter the size of the laundry load or the type of items...towels, jeans, or silky delicates...the washer failed at turning from the wash cycle to the drain cycle. It also leaked because of the lack of draining, and began building up a mold film and odor even though I consistently wiped it dry and left the door opened when not in use. I received no assistance from Whirlpool and was given the runaround and told I must be doing something incorrectly.

Found a crack under a freezer rack from sidewall to back wall. This has caused the refrigerator not to operate properly. Every appliance I own is whirlpool. Bought in 2005. Also bought another in 1994 that is working fine. What surprise me is having a crack in freezer wall. Nothing Whirlpool can or will do! Was a lifetime Whirlpool CUSTOMER. GUESS WHAT? FACEBOOK I GO. 3309 FACEBOOK FRIENDS.

Our Whirlpool 40-gallon electric hot water heater, purchased in 2008, has performed fine, until today when it flooded our basement and, of course, did not provide hot water. As the paperwork says, it has a 12-year warranty. What options do we have for repair or replacement, preferably replacement?I was unable to contact anyone on the 877-817-6750 number due to the bad weather. The model # is EE3J40RD045V, the serial # is 0742130246, and the product # is **.

I purchased and had professionals install a Whirlpool 30-gallon water heater in 2007. Since that time I have had issues with the unit not staying lite, but have been able to deal with it myself. Then in November 2011, it wouldnt work. After paying a plumber to come out and check everything, we got on the phone with Whirlpool who goes through their generic checklist, and after all that they agreed the control was no good. They sent a replacement part out at which time I had to pay to have put in. Now, March 2012, the same thing is going on with the unit. Customer service is their same polite self and have to go through their checklist, but unfortunately we were cut off. This was followed by calls and trying to get the same operator, who was supposed to call me back. It didnt happen. I then called and was hung up on. Finally, I had to work with another operator who again wanted to go through her checklist! She finally agreed the same control unit must be bad and is sending me a new one so I can pay to have it installed! They will not admit the unit is bad and replace it completely. I guess when buying Whirlpool you need to understand they dont back their products. It appears to be normal that a control unit from Whirlpool only has a life expectancy of 3 or 4 months. Last Whirlpool I ever buy!

My Whirlpool washer Cabrio wtw5640xw0 is 2 years old. The computer board is shot, the FOES off balance. To repair would be 554.00 plus tax. I have to say this is the worst washer I have ever bought. My niece told me she just replaced hers that she got 2 years ago also. There should be a recall on this washer. Also I was told the washer and dryer should not share the same outlet.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

On April 10, I bought a Whirlpool washing machine with a sensor. My clothes do not come clean. The dirty spots are still visible. I had three technicians come to check it out and after they just made the machine start, make the water run, and make the water empty, they confirmed that it was working normally. I have insisted on having someone come and just do a small wash and they did not agree because they are not there to wash clothes. I went back to Leon’s where I bought it and the saleslady told me that she could not do anything about it. I have been dealing with the customer service and the person has tried three times to get someone to come and check the washer properly and was insisting in front of me that I wasnt at all satisfied with the performance of the washer and still confirmed that the washer was working fine. They keep saying that there are no parts that need to be fixed or exchanged, so that means there is nothing wrong with the washer. I have tried all different kind of soaps. They were suggesting that I use Tide, which was the best performing soap. I used Tide or Purex - I even tried half a bottle of bleach - and it would not clean my clothes. The problem is the clothes are not turning, they just hardly moved with water that just keeps the clothes humid. I tried putting in more water with a bucket and when I push the start button, it would drain out all the water that it did not put itself. Ive called the consumer protection and they have advised me to take legal actions against the company and the store that sold it to me. They confirmed that whatever we buy, the article has to do the work it was made for; so the performance of a washing machine is to wash clothes. I even took a three-year prolonged warranty and the store told me that once the one-year warranty with the company has expired, then they could help me with sending their technicians and see what the problem was and they would take it from there. I have an account with the store and I have eighteen months to pay it off. So I was wondering if the saleslady did sell me an appliance saying that it was very good and that I should not have any problems with it. Can I take steps going against her for false advertisement? It’s a month now that my clothes are not washed properly and I need to rewash them by hand before putting them out to dry. The consumer protection office has been telling me that the store should be the one to finalize the problem with the company, but it seems that not even they can come to an agreement. Whatever steps I will take against the company and the store, what are my chances of getting my washer replaced? Whirlpool has been advised about me taking them to court and I got permission to do so. Actually, they invited me to go ahead and do what I thought was right. I do not have the money or time to waste on something that maybe I will have no chance to get anywhere. All I want is to have it replaced with another washer that would be more performing. If anyone has had the same problem and had their case solved, maybe it will give me hope to go on. Please, what is the best and fastest way for me to get this problem resolved? I do need a washing machine. I do need to wear clean clothes. Thank you for your patience and understanding.

3-4 years ago, I had replaced my hot water heater with a Whirlpool, which was purchased at Lowes. On 10/23/11, I awoke to a flooded basement from the said water heater. When I entered the basement, I was able to verify that the water was spraying right from the casing of the unit. Who knows how long it had been spraying, but the place was a complete mess. The water was about 10 inches deep and many things were ruined. I proceeded back to Lowes and purchased another exact unit. This morning I awoke to the sound of what seemed to be water bubbling, only to enter the basement and see exactly what I saw just three weeks previously... another flooded basement from water just pouring out the side of the unit. This is an obvious defect in craftsmanship. Now I find myself with a flooded basement, no hot water, and a decision to make. Do I fight for another replacement or give up on the brand? A replacement water heater will solve my lack of hot water but for now, the question is for how long? Not to mention the cost and time spent with the clean up I did twice.

Whirlpool Gold Freestanding Accu bake Duo FIRE HAZZARD - We bought our house August 2013 and we were SO happy to see the stainless steel appliances and we thought Whirlpool was a good brand that our grandparents stood behind for years (they obviously havent bought from them in 50+ years... times must have changed for the worse). Anyway, I got all moved in and was fixing supper and noticed how REALLY dark and greasy the oven was. I could barely see inside because the coating of grime was so thick that it dimmed the light by being so thick over the glass bulb cover. I immediately thought Wow... the past homeowners were nasty and lazy because they have this nice self-cleaning oven and dont even bother to clean it. I noticed it smelled slightly like it had a gas leak somewhere when it was preheating but it cooked the supper okay that night.Because it was hotter than a jungle in NC in the summer heat of August, I decided to wait until winter to use the self-clean... thought it would warm the house as it got rid of the gunk, right? I kept using the dark coated oven about a total of 25 times and always noticed the faint gas smell at first when it would preheat. I thought maybe it was SO dirty that the oven seal wasnt working right and since it was now November, I figured I should just run the self clean cycle and maybe it would make it run properly as it was REALLY dirty and the igniter or something may actually be clogged. I figured it would probably stink a little at first when it started the cleaning cycle because of the excess build up but it needed cleaning so bad that I cleaned it... The smoke alarms started to go off, we just disconnected them for peace and quiet... Our throats and eyes were burning and it smelled more like plastic burning... FOR HOURS it was horrible! The walls and the Terracotta tile floor were flaming hot!!! The next morning the house actually smelled like it had caught on fire and it stayed that way for weeks!The oven was very clean inside after the cleaning BUT the oven is now totally useless! It will not stay lit. I have never been able to use it again as it will not come up to temperature... just clicks over and over and hisses trying to light. I tried again today and it started LOUDLY hissing like a big open gas pipe was on in there and I got scared and cut it off. THANK GOD it went off!I have been reading similar complaints about Whirlpool Gold ovens for a couple hours now and I am truly scared to use this oven now. After reading the comments of the hundreds of dollars it will take to get it to bake again and how most people STILL had the same reoccurring issues and NO help from Whirlpool... Well I decided to share my experience in hopes that if anyone else is reading this... and I am sorry to say... Well... you are not imagining the problem either. We never read these blogs like this BEFORE we buy or use our appliances, only AFTER something scares the crap out of you and you look for a recall. If I could afford to sue Whirlpool for a replacement then I would. I wish everyone could afford to sue Whirlpool for their unresolved issues that have cost them unnecessary expenses due to the customer loyalty we have had for Whirlpool as we used to be taught You get what you pay for and Do not go with an off brand because those companies go out of business when you need them to repair or service stuff. Am I the only one that was taught this? Times are very hard now and the economy is getting worse and now we have to be screwed by big companies like Whirlpool getting rich off of hardworking people and they do not care enough o help pay for the poor workmanship issues they are making. Shame on you, Whirlpool. I am taking the rest of the day to read reviews on a replacement stove so I can get this ticking time-bomb out of my new home. I too have read enough about the same oven that others have had worse memories than I did. I will not waste anymore of our hard-earned money on Whirlpool ovens. You have to decide what is good for you....

There seemed to be an issue with the Whirlpool Cabrio Washer Pump. If a button comes off from your clothing or snap, etc., it gets trapped in the washer pump, causing it to crack and leak. Whirlpool on warranty only allows for one free change and anything after that costs $300.00. This is going to be the third time we are having problems with this and it is becoming, economically, a struggle for us. We have checked every button and snap to make sure they are fastened tightly, as well as any other type of items that may fall off in the wash and become trapped in the pump causing it to crack and leak. These pumps were poorly made and Whirlpool needs to be more aware of this problem rather than telling the customer that they are not aware of the situation.

I purchased a Whirlpool electric water heater from Lowe’s in 2007. It lasted 2 years until a faulty weld on the tank started leaking and flooded my basement. Whirlpool did replace it. However, my second water heater did the same exact thing in a different location on the tank after 2 1/2 years. It also flooded my basement.I am now on my third Whirlpool water heater in 5 years and the one I have now has a bad thermistor. It has cost me about $225 each time the water heater has been replaced. In my opinion, these Whirlpool water heaters are junk and their quality control needs to get out of the break room and start doing their job. Never will I purchase another Whirlpool appliance.

What a piece of expensive junk! Do not buy it, does not clean clothes well, lid broke, lock broke, now it just wont start. Parts are super expensive. Next one I buy will be a basic washer, forget all the bells and whistles!!

Thank God for this website and Frank of Dover (postings on Feb. 11, 2013 and Jan. 7, 2011). We just had exactly the same horrid experience with the lid on our Whirlpool Cabrio Washer WTW7800XW. Just as with Frank, our home warranty provider first accused us of abusing the machine. I merely printed out Franks comments and description, whereupon the home warranty provider reluctantly agreed to replace the lid. We also bought an extra lid and are keeping it in our attic for the next failure. Do not purchase this washer!

My dishwasher is more than 10 years old. It functions but the interior baskets have broken and because my counter overhangs a couple of inches from the dishwasher the steam from the dishwasher has damaged the underside of the counter. It cleans ok but I would not buy this kind of dishwasher again.

I purchased the extended warranty for my refrigerator and the warranty company sent a technician out to repair my refrigerator. It has been six weeks and 4 attempts and no one can do anything to fix it. The warranty wont refund my money without deductions from the company coming out and fixing nothing and says itll take 2 weeks before I can get that. After mailing in writing that I want to cancel 500 dollars wasted and no one wants to help. Thanks Whirlpool. Ill definitely let all my family and friends know of my experience.

I purchased the washer 1.5 years ago. At about 9 months, the latch was in need of replacing. The washer was locked and would not unlock. That was fixed. Fast forward to 1.5 years old and the control board needs replacing. The washer stopped in the midst of a cycle, filled with water. The repairs are over $400 -- nearly the price of a new washer. Ive never had a washer to go out on me. I willingly gave away my previous washer for the purchase of a newer model and did not expect this fiasco. I will recommend against purchasing a Whirlpool washer.

Ive owned my Whirlpool appliances for almost a year. So far Ive had 4 maintenance calls for my dishwasher to be fixed (over and over) and once for my refrigerator. Yes, its currently under warranty, but Im afraid to keep it without an extended warranty due to all the issues Ive had with them. So, now Im going to be spending hundreds on an extended warranty. I will never buy another Whirlpool.

Please read if youre thinking about buying from Whirlpool - the Whirlpool front loading washing machine. Hmm, where do I start? Oh yeah, its a colossal piece of garbage. Four years ago my wife and I went shopping for a washer and dryer. We looked at quite a few and then we came across the Whirlpool front loading washer. Ah, the wave of the future. The end all solution to your washing needs. The best the market has to offer and at over $1,100, they should be. The salesman completely sold us on why we should spend a little extra for such a superior product. I thought, I work hard. I dont make a ton of money, but this sounds like a long term, worthwhile investment. Wrap it up, the washer and dryer combo. Fast forward 4 years later. Whats that awful clunking sound the washer is making? Oh, its the drum. Maybe its off center. I opened it up to find that the spider arm is broken. Isnt it only 4 years old? Surely they (Whirlpool) will fix this at no charge to the consumer because as I was told 4 years ago, this is the best technology. Now mind you, its just my wife and me. She doesnt have to do laundry for 50 people or even 4 for that matter. Calling Whirlpool (ring, ring, ring. Hello, this is Whirlpool), I explained to them what the problem is and that we have only had this magnificent piece of gold for 4 years. What can you do for me? Sorry sir, the machine is only warrantied for a year. Youll have to buy the $350 part to fix it. Reading between the lines, Youre screwed sucker. Thanks for the cash. Really, youre telling me that I spent almost $2,000 of my very hard earned money for a washer and dryer set, and after only 4 years of use you will not fix it? Allow me to paraphrase the reply in laymans terms. Nope, youre ** and thanks for the green. Here are my thoughts on Whirlpool. They are one of the worst companies out there for customer service. The front loading washing machine is a horrible product that should be pulled off the market and never be sold again. My experience with this company will never happen again because I will never ever buy another one of their products. So please, before you think about giving them your business by buying a front loading washing machine, think again. And remember this - I now have a $1,100 paperweight.

Purchased this dishwasher in January 2012, and it stopped working in May 2015. We replaced thermal fuse a year ago and just had to replace the control panel. It worked for 1 day and through 2 wash cycles, but during the 3rd wash cycle, it failed to drain and no power again, which is the same problem we had before. We opted to also replace the control board, just to be safe. Lol. What a piece of junk! Whirlpool is a pathetic excuse for a company, and, judging from others experiences with the customer service department, we will not bother contacting these ** since they clearly have no interest in providing any service at all to their customers. I have had many other lower end dishwasher models, and all of them worked well past the 5 - 10 year mark and never stopped working or required any service. I WILL NEVER PURCHASE ANOTHER APPLIANCE FROM WHIRLPOOL AND HAVE SPREAD THE WORD TO EVERYONE I KNOW. Good luck, Whirlpool. I do not expect they will be around in 10 years. Lol. Do not give your hard earned money to these idiots for the junk that they peddle, and please let your local appliance dealer know why you wish to purchase any other brand BUT Whirlpool. Consumers are not stupid, Whirlpool! You are ignorant for banking on that and should be shut down for your unfair business practices, not to mention misrepresentation of your despicable products.

The reason for the call was to find out how to file a claim after replacing the ice maker and paying for it the 3rd time, they were very argumentative and would not listen to me about the design flaw in the wire harness that burns up the motor for the ice maker. I found out about the design flaw from talking to the repairman that replace the ice maker who works for Dick Kearsley Clearfield UT. He told me that Whirlpool knows about the problem for the 22 cubic foot and 25 cubic foot refrigerator and that is why they have 2 different new wire harnesses in the box for replacement of the old wiring harness.

I bought a Whirlpool washing machine from Home Depot 4 years ago. It immediately started to grow mold in the seal even though I wiped it clean after usage. I called a certified technician to replace the seal. As he was removing one screw on the lock the Washing machine shorted out essentially destroying the panel and rendering the machine broken. I called Whirlpool and told them that the machine was defective otherwise, why would it do that? My technician has worked on hundreds of machines and this is the first time this has happened. The two managers I talked to refused to help me because I didnt have an extended warranty.It is true that I dont have an extended warranty but also, I had faith that Whirlpool had sold me a good product. There is no other explanation for the washing machine to do that other than it was defective. I asked the managers to send me replacement parts, but they refused to do that. The last machine I had was a Maytag that lasted 20 years and when I gave it away, it was still working. I expected no less from the Whirlpool I purchased at Home Depot.

We purchased our Whirlpool refrigerator in 2010. A year or two after the purchase the side walls, draws, and shelves all started to crack open. We asked whirlpool to send new parts. They sent one and that cracked also. We will never buy from them again.

We purchased the extended warranty (service plan number **). The washing machine has been giving trouble. It locks out during every wash cycle and each time, we have to unplug the machine to reset it. Sometimes it makes it through the next cycle and sometimes, not. The first couple of calls we made, we were told to make sure it was cleaned, to make sure it was leveled. All this was done and we still have the same problem. Finally, a technician was sent out. He could not duplicate the problem and left. Thirty minutes after he left, the machine locked out again. We put in for another call, we were told it would be two more days. In the meantime, we actually video taped the next three times it locked up. This time, when the technician came out, he was able to see our video as well as saw the machine lock up. He stated, It did not give me a code so I do not know what else to do. He left and ten minutes after he left, it locked out again. We immediately called back and they informed us they could not get anyone out again until next week. This is very frustrating to have an obvious problem and have an extended warranty and the problem cannot be solved. We feel as if we are being blown off. Is there anything you can do to help us and/or give us advise of how to get this problem resolved?

My range was made after this date and needs this Service Bulletin part. Whirlpool refuses to ship at no cost. I have spent money on this already to discover they knew the issue in April 2004 yet sold the range in October 2005. Rena in service stated she is the highest authority at Whirlpool anyone can talk to!

I bought a 38 gal. low boy electric Whirlpool water heater from Lowe’s. It was replaced because of a leak around the upper heating element after only one year. Now, the replacement heater is leaking in the same place, and it has been leaking so long that the electric terminals are rusted, water is standing in the cover plate, and the lining is soaked. I cannot see behind the plate and dont know it until the water finally made its way into the drip pan beneath the heater. When we saw the standing water, we turned off the electricity and shut off the water to it to stop a fire hazard. The warranty is up on my water heater, but my concern is that this could cause someones home to burn.

In January 2021 I purchased a front load Whirlpool washer and matching dryer. They were delivered on February 6 2021. The first load we found water on the floor. I thought I didnt close the detergent drawer so I proceeded with the next load. Again I found water this even through the ceiling tile in room below. So with the next load I sat in laundry room to see what was happening. When on the rinse cycle water shoots out the front of the dispenser drawer.Contacted service, they sent repair man. He ordered new parts and I waited over 3 weeks for next repair call to find out that whirlpool had part all along. Repair man came again and still no resolution to issue. He was told to order same parts again - still no resolution yet again. I fought with Whirlpool till they said they would give me a new machine. Now fighting because delivery people wont uninstall 1st washer and install new machine. Today is June 28 2021 and I still DONT HAVE A WASHER TO USE. I havent even used the dryer yet. I have $3400 and numerous hours with Whirlpool trying to resolve this issue! Can you help? Whirlpool continues to string us along, telling us to be patient, theyre doing their best.

The dishwasher is less than 2 years old, out of warranty, and will not start. The repairman said the problem is in the electronics. It would cost $500+ to repair.

Bought a Whirlpool 25 cu ft side by side in 2011 and now just 4 years later the compressor is bad. Called them and they only have a 1 year warranty, which is nothing for a compressor. They told me for $350 they could replace it and it be good for only a year. Not going to sink more money into a product even the company has no confidence in. The repairman advised to stay away from Whirlpool as they were not the company they used to be. Also the salesman at Lowes where it came from said they used to have a 5 year warranty but changed several years ago and the quality also went down. We have had refrigerators last 25 to 30 years in the past but no more thanks to modern technology. Thanks a lot. STAY AWAY FROM WHIRLPOOL!

We bought Whirlpool Frontloader Washing Machine not over 1 month ago and it started to malfunction showing Ed1 error on its display. We contacted the service center and it was taking too long to have a visit from a technician. Then the technician, who also installed the unit came and checked the unit. He called someone from corporate office or from support team to ask what is error code Ed1 and overheard over the phone that this is a known issue on the brand. The technician said it is possible that unit will be replaced or only the motor. I contacted the brand support thru Messenger and requested to have the unit replaced, because again, the unit is not over 1mo old.I was advised it is not possible as replacement of unit is only applicable when the issue happened within seven days of delivery. STUPID ISNT? Policy is something unworthy for a product that is over 30k. And again, unit started to malfunction not over a month after it was first used. I would say we pretty much took care of the unit, we only use it twice a week. Placed it where it was perfect to put. Followed every advice given to us by the technician who installed it but still, it malfunctioned a few weeks after we started to use it. I am ashamed of the brand itself, we should have chosen Panasonic or Samsung instead not a dumb brand like Whirlpool. I certainly do not recommend the brand for a washing machine unit. Frontloader is a crap.

I have used Kenmore products for about 50 years, so when it came time to replace my old washer I looked at Kenmore/Whirlpool. I upgraded to the top of the line. I had been warned by 2 service techs (2 different companies) that had tried to keep my old Kenmore alive that the new ones are not up to par compared to the old ones. The first very small load that I tried, was not even thoroughly wet when I took it out to put in the dryer. 1st service call, tech suggested that I put machine on extra water.That helped sort of. A few weeks later, wash is not getting clean. Called Whirlpool, they suggested getting the washer cleaner and clean the washer. Went out and bought a special cleaner, $10-12 and two cleanings later using the extra water and extra wash water I now was getting cleaner clothes. They said I would need to clean the washer every 2 to 4 weeks. I have continued to use washer but frequently have to rewash about 1 in every 5 to 10 loads as it doesnt always clean everything in the load. Called the Co., they sent service out, they said its OK!In Jan. We went out of town for 2 weeks. The washer had not been used for 4 days before we left. Came home to water all over the floor which are hardwood. Needless to say our hardwood is all warped! Service came out, ran the washer for about 15 min. and said it was fine, nothing wrong! Called Whirlpool again! Washer is now out of warranty. They said call a local service, out of their hands as it is out of warranty! Nothing more than they can do.I have used Kenmore/Whirlpool Appliances all my life and they have been wonderful. The new ones are garbage as far as I can tell. I have a Refer that is now 3-4 years old and I have had problems with that, a new dishwasher that is 2ish and have had service out on that one, now my brand new washer top of the line and it is so bad I am afraid to use it unless I am sitting right in front of it watching it! Further if you have the rinse cycle on the clothes come out so wrinkled that you need to get out your iron out and iron everything including sheets and linens. Lucky that I did not replace my old dryer! Do I recommend Whirlpool anymore? Not on your life. I wish I knew what to replace them with!

Its a very well build dishwasher. Its quiet, really do a deep cleaning and make it easier to leave the kitchen clean after dinner with 2 kids its something that I need, Its not pricey either like other brands.

Our new home came with brand new appliances. I love our Whirlpool microwave. Its reliable, quick & has lots of great pre-programmed features to assist with regular. The independent timer is a total bonus too.

We got a brand new bottom freezer french door Whirlpool refrigerator in our brand new apartment. Since we moved in last week the temperature control in the refrigerator box has failed three times. The freezer stays cold but the coils are frosted solid and no cooling gets up to the refrigerator box. We turned on moisture control but that didnt help. The users manual is completely useless and in fact doesnt even match the control panel. The numbers for temperature settings on the instructions dont match the numbers on the panel.We had to turn off and thaw out the unit completely three times already and this is just the first week! Last night the building maintenance guys came in and sprayed the back panel of the freezer with warm water. He said he talked to the GE tech, who suggested we also increase the freezer temperature settings to 4 and the refrigerator to 44. But this morning the temperature rose again. It sure sounds to me like the daily defrost cycle isnt running at all and nobody wants to consider that possibility. Thaw the unit several times a week is completely ridiculous. Our food has experienced so many temperature excursions who knows whether its any good now. I cant wait to get my first taste of salmonella. This is what you get when you combine junk with poor service.

I have never posted a negative product review but must do so now. The refrigerator is 1 1/2 years old at most and has been well taken care of. I noticed today that the finish at either side of the bottom of each refrigerator door handle has a problem. I couldnt tell if the finish was pitting or is just discolored. I called customer service and expected that they would help, especially since we have an extended warranty. Representative number one told me that the extended warranty only covers problems that affect the function of the product. I spoke to her supervisor and then her supervisor. I got plenty of apologies but no support. I offered to send pictures, but they were not even interested in checking out the problem.After speaking to them, I took the handle off and I see now that the handle cut into some sort of film that exists on the metal. (I am not talking about the protective plastic coating that is on the the refrigerator at delivery.) The film is lifting off the surface and creating discoloration. If Whirlpool was at all concerned, I think this issue could be fixed with some sort of gasket to keep the metal handle from cutting into the surface. Im hoping the problem is static, but hard to say what will happen. If they had been interested in trying to understand the cause of the problem, it would have been easier to accept the limitations of the warranty. It would have demonstrated an interest in avoiding this problem for other consumers in the future. My last Whirlpool product. Period. Good luck if you decide to do business with them.

I am writing due to the defects and flaws in my recently purchased appliances. I chose Whirlpool believing I was buying the highest quality for longevity purposes. Every appliance I own is Whirlpool or Maytag - same company. I purchased warranties and was told the warranties dont cover my issues and was basically brushed off. I am infuriated. Here is a list of complaints. Refrigerator is cracking on the inside on the inner door and at the bottom. These cracks surfaced within the first year of purchase. The warranty does not cover cracks in the inner body.The oven/range has an exhaust that bellows out of the top of the range in a way that the smoke curls up onto the panel and discolors it. I have never had an oven constructed with an exhaust pipe in the front that pours smoke onto the range itself and into your house. The dishwasher paint has rusted off on the door as have the screws on the inside of the door. The cover panel on the cleaning dispenser of the washer has popped off and cannot be popped back on, hence the guts of the dispenser are always visible and when I go to load the cleansers the front has to pulled out from inside the dispense.The refrigerator is also leaking from the bottom and the ice-maker no longer produces ice. This started off and on for the past 2 years. At first I thought the leak was from a near by window. No it is the refrigerator. All of these appliances were purchased in 2013, 14 and 15. New. I am 56. I have never had issues like this ever in my life growing up or as an adult. Appliances lasted forever. I am one person. How much damage could I do? None.These are flaws in chemical compounding of the paints and materials for cracks and rust. Whirlpool was called various times and was not interested in sending a rep to verify my claims. They said all of my warranties did not cover such issues only motors. Lots of many spent in vain. I will not purchase Whirlpool again as they seem disinterested in customer satisfaction.

Bought this from Lowes in 2010 with the 12 yr extended warranty. Have not been able to keep it lit. Takes 4-10 days for repairman just to LOOK AT IT and then he usually has to order a new control valve, taking another 2-4 days (have had the control valve replace 3xs). This means, my husband has to get down at eye level to try to get it to light (hes 63) & if it doesnt light on the 40th try or the cramp in his hand stops him sooner, we have to heat water on the stove, carry it through the house to the bathtub, try to get the temp not too hot or too cool, then hope that our 70 yr old bodies can get down into the tub plus get back out without falling (showers are preferable). My husband bought The best hot water heater $ could buy at our local Lowes store. Because we are getting up there in years, we hoped that this would be the best answer by also getting the extended warranty. They have had numerous repairmen out to our house (6 or 7 last count)... two different men told my husband that they would only be here a couple of minutes knowing it was not going to light for them either. Time wasted. Patience gone. Still they wont replace it because if anyone can get it to light up again, no matter how long that may take, then theres no need to replace it! They have already put more money into parts, labor & repairs than it originally cost. I was told today by the ex. warranty representative that its not considered a lemon! So how do those LOWES/WHIRLPOOL people sleep at night????

I apparently am one of the lucky ones to have an electric water heater. My unit started giving me failure codes during the Christmas holidays. Each time it would fail, I would get a different failure code indicating the upper element, the lower element, and a sensor failure. After testing all 3 of these components, it was determined to be a controller issue. After speaking with Chris on the phone, he overnighted a new controller to me. I installed the new controller and had no more failures. Hot showers for New Years! Thank you Chris.

From day one I was not happy with the new auto fill washer, I was told I just needed to get used to it! Well I have tried every cycle available and no matter what I try cloths don’t come out clean, using the deepwash cycle Sheets on top were still dry once cycle was completed!! Give me back my old washer! Washed much much better.

Purchased model # WRX7355D8MOO through Lowes summer of 2013. By summer of 2014 ice started building up under freeze drawer. Little did I realize the compressor was failing, air flow was stopped up. Ice maker failed. In 2016 water dispenser calibration off, freezer failed. Called in certified Whirlpool repair. They spent three days troubleshooting problems. Repairmen told me, not to spend any more money to repair this fridge, buy a new fridge. I spent $2300 on this fridge. Its only 2 1/2 years old. Whirlpool better get their quality control issues resolved or shut down the plant. I know many part are made in Mexico, poor quality. Why pay for an expensive appliance that only last two years.

I purchased a washing machine in year 2002. It was working perfectly. Recently, its drive belt started slipping. I called local service center, S. R. Enterprises, with mobile number 9204792391.The technician came after 3 days and declared that the gear box is leaking and will have to be replaced. They had no gearbox in stock for model f45, top loading, fully automatic.After a wait, they took away the machine to their workshop on 30.09.2011 and returned it on 04.10.2011.They charged me Rs. 4,730. I will have to be replaced. I found that its LID, which was perfectly okay, is now making a terrible sound when opened and would fall down, not allowing to load the machine. I informed the service center immediately. After many reminders, a man turned up yesterday and declared that the LID will have to be replaced and I will have to pay Rs. 2,000 for that. I rang up the service center to say, Since it has been damaged in your workshop, you should replace it free of cost to me. Their reply was evasive and negative. I called your call center and they registered my complaint - customer number **, comp. number **. I was assured that the LID will be replaced within 24 hours.

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

I purchased a french door refrigerator in March 2013. I purchased the Gold Series because I wanted the best. I have come to the conclusion that Whirlpool does not make a refrigerator with the quality to reflect the Gold Label or any label. My ice maker system created ice dams inside the fresh food area, in the ice bin compartment and allowed water to run into the fresh food area and floor. After four repair visits, I am still dealing with occasional water running down the inside of the ice maker door and into the fresh food area. I contacted Whirlpool and tried to get the defective refrigerator replaced; however, the very rude customer service representative insisted on another repair call by A&E. They scheduled the appointment for a time different than we agreed upon, so at this point I have had to cancel this appointment. I do not know why anyone would want to buy an appliance made by Whirlpool, which includes several other brands.

Bought a Whirlpool Cabrio washer and dryer 5 years ago and with only 2 adults and 4 washes per week, it broke down twice needing new motherboards each time and, of course, Whirlpool would not take any responsibility as the 1 year warranty had past! I will not buy another Whirlpool!

My wife and I bought a Whirlpool water heater NU50T121-403, SER# 0733323 as we researched online the best efficient water heater for the money... which was actually more than we budgeted for. We purchased it from LOWES and our Plumber had to return the first heater due to a huge dent on the outside of the body once it was removed from the box. LOWES replaced it, no problem and he installed it. GREAT, HOT water for about six (6) months. Pilot light went out and has continued failing after relighting numerous times! Now we have the four (4) blinks indicating that the Honeywell gas control needs to be replaced only after 27 months of use. Whirlpool offers 12 year warranty on tank & parts, but come to find out, not this part. We were both raised on Whirlpool products and thought we based on our parents successes of various Whirlpool products, we were buying quality brand. We were soon disappointed and will never buy another Whirlpool manufactured Brand again!!

Once again I am disappointed in a product that I felt was of the utmost quality. However after buying in 2010 and not being installed until 2011, the over the oven microwave has a crack on the outside of the door. Two pieces have fallen off from under the plastic rim on the inside of the door, two pieces of the door one on the top right side and the other on the bottom right side have fallen off. All I have to say is the two Whirlpool products I bought at Lowes has been a huge disappointment especially since the other two bought from the same stores are Frigidaires and work beautifully...

WTW6340WW0 - When washing clothes, on the last spin it stops and gives an UL error message. I make sure all the clothes are level and restart at that point but still the UL error message appears and water starts leaking from the underneath of the machine. Weve reset the and unplug the machine but no difference. Please help on what else to do.

I purchased their washer, dryer, refrigerator, freezer, oven, and dishwasher. All were brand new when my home was built in 2006. Whirpool is the absolute worst home appliance company in both customer service and product. I would save my money and purchase any product other than a Whirlpool or Maytag. All of my appliances are a little over 5 years old and all have had multiple problems. Corporate takes the attitude of oh well, pay for the multiple repairs or buy new after 5 years or less. Ive never heard of disposable appliances, but Whirlpool has a full line of them! I would rate them less than 1 and just plain **!

I wish I could give negative stars! My Cabrio Model #WTW6600SG2 sounds like a jet airplane on the spin cycle (this started 2 months ago). Now, Im getting the UL error, its not an an uneven load!

Bought a Whirlpool Cabrio Washer Dryer combination on 4-5-2009, had it delivered on 4-20-2009, was very excited to get this set as it was like my first ever brand new washer dryer. I thought Id spend the money get something good and it would last for years and years. Was I ever wrong. I bought the set and the extended warranty from Lowes and my total with delivery was 2579.00. 20 days after the extended warranty expires (that I never used) the bearings on my Washer go bad. This thing in spin cycle sounds like a jet engine. I called to see if Lowes would still honor my warranty because I never used it and they said no. I called Whirlpool and checked to see if there was a recall and they said no. I checked to see if there is anything they could do at all because this is a huge known issue and of course they said no. (Just look on YouTube for Whirlpool bearing replacement and the amount of views should indicate the amount of troubled users.)Called a repair scheduled through Whirlpools website to come look at it for a 75 dollar assessment and they said it would be about 500-550 to replace the outer tub - largely due to the fact its labor intensive and the bearings are packed in the outer tub from the factory. I was like are you ** kidding me? I paid 1029 for the unit brand new in 2009 and 550 to fix? I said thank you to the repair guy and escorted him nicely out. Upon that I called back Whirlpool to tell them how displeased I am and how I will not be another product of theirs ever and mostly due to the fact they know this is a huge issue and wont do anything about it. I will be going to Lowes to see if the guy who sold me this pile of crap will work me a deal on another unit or set of another brand after I show him my receipt and express my displeasure with that product. If they wont do anything I will go to another store and spend my money elsewhere - I have choices and others do too. So if you are thinking about buying anything in the Cabrio line, dont. Go Samsung or LG - 10 year warranty straight from the manufacturer and costs 200-300 less than I paid for my washer dryer 5 years ago. The bearings are ** and shouldve lasted a lot longer for the amount I used this machine and for what I paid! Shame on you Whirlpool for using crappy parts to make your machines.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

My gas range doesnt work all that well. Sometimes the flame catches and lights, sometimes it doesnt. Oven seems to be less than steady in cooking. It is ok, but I wouldnt buy again.

These are the worst sets in the world. We bought this set from a hometown store, had them 6 months and all belts on dryer had to have the belt on the dryer replaced, then 2 months later the washing machine went out, so the store did replace both and weve had them about 3 month. The dryer works great so far, the washing machine on the other hand not good at all! The tray where the detergent goes continues to have mold/mildew in it, the clothes come out of wash cycle smelling soured. We have this set inside and we keep our temp set on 67 in our home. There is no excuse for all the problems, not to mention that noise it makes when it washes!! I am completely disgusted!!

Sept. 2011 purchased new Whirlpool bottom freezer model GX2FDXVA03 and in Dec. 2015 had to replace it after paying for 2 service calls, last time was told cant be repaired. First found ice in bottom of freezer which was caused by Whirlpool installing a rubber nipple at bottom of drain line with such a small opening it clogs quickly. Couple years after that stopped working had to replace circuit boards, now its leaking Freon and no way to be repaired. If you call Whirlpool all you get is big circle of feel good call centers. Best offer was discount on new refrigerator. Told the person Why would I want to spend another $1300 on junk?

I want to make this clear I’d give NO stars if I could!! Whirlpool is totally junk!! I bought a whole suite of Whirlpool kitchen appliances from Home Depot that is a dishwasher, stove, and fridge. The dishwasher never cleaned the dishes, always left a film on everything, cant clean out the drain area, the screens don’t come off and less a year later the dishwasher top rack literally fell off and broke all the glasses that were loaded in it and the fridge keeps freezing all my food!!! I keep having to adjust the thermostat up down up down just to make it doesn’t freeze. Now that the warranty is no good on any of the crap I will no doubt be charged an arm and a leg to get it fixed, which definitely won’t be worth it!!! Whirlpool is such crap!!! Made in America no wonder!!! Don’t buy any whirlpool anything!!! You will be very VERY disappointed!!! I’ve bought plenty of brand new appliances. Bosch is by far the best dishwasher even the cheaper ones. Now I have to pay to dispose the whirlpool crap!!! I am sure whirlpool doesn’t give a crap though!!! They will keep selling their crap, but don’t Buy it!!! You will be soooo disappointed!!!

Whirlpool Water Heater FG1F4040S3NOV - I had this water heater installed in 2005 by a professional plumber and every year since like clockwork, I have to replace the gas control valve/thermostat. Last year, Sears came and did the work and made their arrangements to have the part replaced. This year 2012, March 9 my gas control valve went again. The unit is not even a year old and broke again. Unfortunately, the six-year warranty is up on the hot water tank. I called Whirlpool two times. The first time, the guy told me that the warranty was up and hung up on me! The second time, the guy would not honor the replacing of a part that is not even a year old yet. The money I spent over the six years making repair on it, I could have bought a new one. This company is nothing but a bunch of **. Is there anything that I can do? I have paid to replace this five years in a row.

Whirlpools front load washers do not have easy access to the drain pump filter. The entire front of the machine including the door has to be taken off to access the filter. When putting washer back together the parts are cheap and screws break. Most companies that sell front load washers provide easy access to the drain pump filter. Buy one of those instead of a Whirlpool and you will save yourself a lot of time and hassle.

I purchased at Lowes and they say was without warranty. I have had all kinds of trouble. The pilot light was replaced in the burner easily because of recall. Now the pilot will not stay lighted unless you tap on the gas valve. Then as soon as the water temperature comes up, the burner and the pilot light go out. I went to Lowes for a new gas valve. They have one for natural gas of $58. They do not stock for propane. I have to purchase from Whirlpool which costs $228. Their comment is that it is more expensive to build another. They do not change offices any longer because of PSi difference bull crap. I purchased a Whirlpool gas stove 2 to 3 years ago and I had to purchase an LP change over kit to use it. This is nothing but a case price extortion. I will never purchase another Whirlpool product again and I would advise no one else either!

I had this same refrigerator in another home and had no issues, this particular one now I have nothing but issues with it. It seems that the quality is not consistent. First the ice maker was not working, then the freezer light burned out and now there is extensive frost build up in the freezer. The refrigerator is only 2 years old!

Never again will I buy a Whirlpool product. I paid over $800 for a new washer 51/2 years ago. I had it worked on twice under extended warranty. Now the bearings are out of the tub and it sounds like a jet taking off when it spins. I had whirlpool products in the past and they lasted for years with no problems. I have a friend who has a relative who is an engineer for whirlpool and his job is to engineer their products so they fail within a certain time frame. They dont want them to last like they use to. They now have gotten their product line to the point where they can tell when it will fail. This is crap. What happened to products that lasted like they use to. NEVER BUY WHIRLPOOL.

We are on our 3rd washer and second dryer in 10 years. Our latest replacement (Whirlpool Duet Washer and Dryer) was purchased 3 months ago and is already broken and now we have been without a washer for a whole month. Not only do they have issues with the control panel and latch, but they smell. The dryer also had a control panel issue. Trying to get our units fixed presented even more problems and wrong parts would come in, with weeks going by without parts/service. Apologies and sympathies expressed on the phone are not enough. When you buy a matching set and only one breaks, you tend to replace the matching unit, which we regret and we went back and forth with our washer and dryer. I would never recommend a Whirlpool product after this. We finally got a replacement today and due to more poor communication on their end, they could not hook up. My new washer sits in the laundry room, and I hate it before I even get it hooked up.

I purchased a Whirlpool washer 7 months ago, and a month ago, it broke. I have been without my washer for 1 month, and it has been repaired 4 times in that month. It is still not working. All I get is that, its under warranty, and there isnt anything they can do, but to keep trying to fix it. I have been having to take my clothes to a laundromat, and pay to have them washed. I have asked for them to deem it defective, but they refuse.

This Cabrio washing machine is really frustrating....... It goes off balance all the time. It does not matter if you have a full load or partial load, I know it has a tendency to go off balance, so I try to put the clothes in evenly. BUT it doesnt matter, it goes off balance. When the washer is downstairs, it gets to be a pain. The lid lock is a pain also. If you forget to put something in the machine, you hit pause button then you have to wait forever until it unlocks, and wait forever to unlock when it goes off balance. When it doesnt go off balance, it washes everything just fine. But if I knew what I know now about it, I would have never bought it....... I would recommend a different washer and check the reviews, which I didnt do. :(

We purchased a Whirlpool Accubake Drop-in Stove (Model # RS675PXG015) on 10/21/2006 from Lowes Companies, which cost $1,100.00. In 11/2012, we had an error message E1-F2, and we tried everything to get it to clear - all suggestions given by electrical repairman who does repair for Lowes Cos. The stove is porcelain, which also has problems of staining that cant be cleaned. We were told the repair would cost $200 for the panel, and if that doesnt work, another $400 for the other panel. In reviewing other complaints for this Whirlpool stove, there are enough complaints to recall this item or at least give deep cuts for the parts to repair this stove. We have purchased other Whirlpool items, and this one is not well made and too costly to repair. It should last at least 15 years or more. Cant Whirlpool do something about this obvious problem?

Purchased the Whirlpool DU915 in 2004. Its been 16 years and I havent made a single repair. A lot of that is just proper use, i.e. scraping off food stuff, using correct soap, etc. I have other newer Whirlpool dishwashers at rental properties which have required repair due to misuse. I would recommend Whirlpool products to friends and family.

We bought our stainless and black Whirlpool stove last month. We love that its black topped, and doesnt show dirt. We love how the oven door seals, and the fast heat. What we do NOT love, is how easily the knobs turn. You barely brush against them, and gas leaking into the kitchen. I called for service. Our guy said yes, they turn easier than most of the stoves he has worked on. He called tech support from my kitchen, and I overheard the guy at the other end. His response was dismissive. I have had gas ovens for 20 years. They have without exception, had a spring type feeling to the knob. This stove has none. I am writing this so that if others are experiencing the same thing, they will see it is not their imagination. Something is wrong with the design of the knobs or some part is missing.

I bought a Whirlpool dishwasher. It has a plastic removable cap to pour in the liquid for their Rinse Aid drying. It is something like a bottle cap, a 25 cent part. I lost it. I called up, they wanted 12 dollars for the part and 9 dollars for shipping. They refused to just put it in an envelope and put a 30 cent stamp on it.

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

Whirlpool Cabrio washer - Its been a month now and still the washer is not fixed. The repairman through Lowes warranty service is the worst by far I have ever dealt with. I had new transmission put on, still wont agitate and smells hot. The washer is only 18 months old, well taken care of. This expensive hunk of junk is worthless and the aggravation for all this mess is worse. I called Whirlpool 2 times. The first time, I got a call with the standard oh so sorry bit. Oh boy, that gets the washer fixed. Not. I blasted them and Lowes again. I have had it with this mess. The repairman is supposed to contact Lowes a week ago for replacement. He has done zero. I called Lowes to check. How can they sell this junk to customers who pay for this washer? They know it is junk, Lowes and Whirlpool, so do the right thing and recall the junker for refunds to consumers.

It was a complete nightmare buying our all side by side stainless steel freezer and refrigerator. Freezer still working fine but the refrigerator started blowing hot air, all the food spoiled within 2 days as we were trying to figure out what was wrong. The store did the best to correct the problem and it seemed the Whirlpool company had no faith in their product as over the phone recommended having extended warranty. So sorry we bought this product, nothing but hassle!!!

Washer doesnt get soap out of clothes. Had tutorial from service man. Must use extra rinse every time and still have soap on dark clothes. Worst washer I have ever owned. Makes washing a lot of extra work and frustration. Have tried everything to no avail. Takes at least three times longer to wash clothes with all the steps I have to take to get soap out. I understand EPA demands for less water usage, but clothes still must be properly cleaned.

I purchased this washer brand new just 2 years ago. It started making loud crackling noises approximately 3 mos ago. Yesterday it decided it did not want to spin or drain. Today a repairmen tells me its a wash. The computer screen has gone wacky and the cost to replace that will be well over $400, almost to the penny what I spent 2 years ago. This is not a good product Whirlpool and i trusted you since my previous washer lasted over 15 years. I need a refund and a new washer! Disgusted!

I HATE, HATE, HATE the aqua lift clean feature. Its awful. The bottom came somewhat clean but cook bacon and the sides and top are filthy and the aqua lift cant clean that. I dont know how this ever made it past the thought process stage to become a thing but it needs to go away. Im quite cranky right now as Ive just spent two hours scrubbing my oven while reaching past the oven door that doesnt come off because its a self-clean oven. This is what I have to look forward to for the next 10 years until it dies and I can get a new oven? What a joke!!

I have always used Whirlpool washers and dryers. There are many models to choose from to meet a families needs. I can only remember one time when I had to replace an operating part to improve performance.

I have a Whirlpool Cabrio washer (Model: wtw6400sw2 / Serial Number: cu0271913) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool and I will contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!