The washer constantly binds clothes around agitator. Truly a design flaw and it does not get clothes clean. So with a washer like this, I am forced to go to laundromat. Wished I would have paid 230.00 or so to have transmission fixed on old Kenmore. Truly dislike this substandard appliance.

In 2010 we had to purchase a new hot water heater. Went to our local Lowes store to see what they offered. We decided to buy a Whirlpool energy smart electric water heater. It was large, 50 gallon. We have a large family and didnt like running out of hot water so we thought this would be great. Worked fine until yesterday when I kept smelling an odor like something melting. Could not figure out where the smell was coming from until this morning I got in the shower and had very little hot water. Went downstairs and seen the water heater was not working. Got the user guide out to see if we could pinpoint what was wrong. It said no power to control board. I checked the breaker box and found no problems. I got a flashlight to look at the control board and discovered it had overheated and melt the top of it. Have been on phone with Whirlpool nonstop with just a recording. The heater has a lifetime warranty so Im trying to get the replacement part for it that will cost me $115 plus shipping. I am really concerned that with this overheating it did not trip the breaker. Grateful it did not start a fire and worried if we repair it will this happen again and possibly not be as fortunate. I have seen on this site of another complaint with the same problem. Shocked there hasnt been a recall issued. Be careful!

I replaced my 12 year old Whirlpool double ovens with the current Whirlpool double ovens. The new 30 built in double ovens have been re-designed to vent the heat below the lower oven. The ovens come with a part that pushes the heat down instead of straight out. My built in ovens have a cabinet drawer below and after using the ovens just 4 times over the holidays I noticed the heat is damaging the finish. According to Whirlpools service center I should have checked on that before buying/installing. They told me to stop using my ovens, that this is a fire hazard, but they are not responsible. They do not have a solution to this problem. This is a poor design on their part. There is a disclaimer in their installation booklet that came packed with the ovens that the installer gave me. It says the cabinets need to be able to withstand the heat of the ovens. The cabinets can handle the heat of the ovens, just not the hot air venting directly onto the cabinets below the oven. Where does one find cabinets that can withstand 400 degree heat being pushed directly onto them? As a customer I did not have that information until after the ovens were installed and it was too late to purchase another brand.

Every appliance Ive ever owned has been a Whirlpool product. I am on my second set of Cabrio washers and dryers. I havent had any issues with the dryers, but the washers are a different story. My first washer, bought in 2008, started throwing water and oil underneath while spinning. A service technician came out... I had to have the entire tub replaced seeing as how the bearings that went bad were in the motor/spinning assembly that was built into the tub. I moved in 2011 and needed another washer and dryer. I was told the problem had been addressed. Now Im having the same problem... the washer is so loud when spinning, you can hear it on the opposite end of the house with doors closed! So the bearing problem has NOT BEEN ADDRESSED!!! Whirlpool will not stand by this product!! Loyalty is not a factor in their assistance... Only profit!!!

Whirlpool Cabrio Platinum Option - Very stylish. Well built - very solid and heavy constructions. Full features from quick wash to sanitary wash, very energy efficient, steam setting on dryer for touch-ups. Quick loads, etc. We were looking for a washer and dryer set that would accommodate large quilts and blankets and still have the flexibility to handle small and delicate loads, and be energy efficient. The Whirlpool Cabrio Platinum Option is solidly built and very sturdy. It handles small and large loads and is very energy efficient. Both the washer and dryer handle sheets and pillowcases without a problem. Wed recommend them to anyone.

This has been our second Whirlpool Hot Water Tank in our home in the past 14 years. The first was installed by the builder, when it went out we purchased a larger capacity one from Lowes. It was professionally installed and now, after the extended warranty coverage period is expired, its expired as well. I would think you should be able to get more than 7 years out of not one, but two Whirlpool hot water tanks. No wonder they are no longer manufacturing hot water tanks - they sucked at it. Also, if you do have one, you have to get parts from Whirlpool and pay $30 shipping. No thanks, for the cost of parts to replace everything youre better off getting a whole new unit.

I purchased a refrigerator from this company Model #WRF989DAM. It worked for only 14 months. I had service people come 4 times to try and fix it, called customer service and was suppose to get a replacement, paid $300.00 for a different model, been 49 days and still have no refrigerator in my home. Had to go out and buy my own replacement. I have called and sent emails with no response of when I would be getting the replacement.

Horrendous product! Purchased December 3, 2014 – had service technician from Whirlpool check the unit for excessive noise 3 months later. Technician said it’s the way it is designed – ice maker in door, air has to be forced up from freezer so it makes a lot of noise! Now, 15 months later, the refrigerator has totally quit. We are waiting for technician from Whirlpool. Obviously, no extended warranty so Whirlpool said they would extend the warranty and cover this visit for $357! How nice of them since they are sure the parts will exceed that amount!!! What a piece of trash – guess the refrigerator is only meant to work about a year! NO MORE WHIRLPOOL! I am thinking about standing outside of Home Depot to warn any customers who are looking for a refrigerator not to buy Whirlpool!Updated 3/23/2016 - To add to our previous review, the service company, AIG finally after 3 days has approved the parts required to fix our with less refrigerator (15 months old.) It will take 8-10 business days for the parts to appear! We have no refrigerator for at least two weeks! Great service from Home Depot and AIG!

My washer is nearly 7 yrs. old. It has almost been a full-time spectator sport. Good thing its in the kitchen! Twists sheets so badly - on sheets setting - that it stops and I must undo the balloon its formed and rearrange the wet, heavy 2 sheets and 2 pillow cases. Now, it cant even finish the clean washer cycle without stopping. It seems it doesnt use enough water to do the job of washing items thoroughly. And it balks at heavy loads - which is what we bought this washer to do - blankets, rugs, quilts, etc. Two people, now only one, and two small dogs. I should have at least 10 years of service from that purchase. Repairman says $300+, and he sees it as a very common code. Build them to last or give up. Im disgusted with Whirlpool now.

Whirlpool Range Model XFE381LVS - 12/13/2014 4:30PM Wife was cooking dinner and turned oven on. Smoke started coming out of the back and called me. I ran to the breaker panel and turned off the breaker. Back to the stove, pulled it out and smoke still coming out in back at the top. I could see fire in the top of the back panel. Slowly the fire went out. Unplugged the stove, I removed the back panel, wires were still smoldering and the Control panel was burned thru. Took pictures so I could contact Whirlpool Monday. The Electrical control panel is destroyed as well as many wires. Glad we were home and oven was not left on while we were out in the yard or Home could have been destroyed. Purchased the stove from Lowes 11/02/2010 with a extended warranty. Tried to add receipt but would not accept, wrong type doc.

I bought a Whirlpool Cabrio Top Loader High-Efficiency Machine on March 20, 2013. 14 months later, it failed. When I called customer service I was informed the 1 year warranty had expired (I knew this already) and that all they could offer me was a $319 extended warranty to fix machine and guarantee covered future repairs. Luckily, I had the machine repaired at no cost to me after complaining to the sales people I bought the machine from the year earlier. They contacted their Whirlpool representative who had the repair covered. Now, 3 years and 11 days after purchasing it, it failed again. This time the machine would no longer spin out the water. Whirlpool offered nothing more than to give the website and special code for a discount on a new machine. After some haggling, they agreed to pay for 50% of the parts only, no labor. I argued this machine must be a lemon, as they have told me theyve heard no prior issues with this machine and that it would be reasonable to replace this machine. They refused any further assistance. So I threw this piece of junk away and instead, for $185, bought a simple rebuilt 15 year old Maytag washer with agitator, direct drive. Just a couple of knobs. No computer, fancy bells and whistles. I can say with absolute certainty that I will never purchase a Whirlpool product ever again. I also believe these machines are no longer meant to last like old washers (and dryers) used to.

2 years ago, I bought my fridge from Home Depot and the delivery people did not leave a manual. I call to see if they could provide me one because I don’t know how to operate some parts of it. They told me they don’t send manuals anymore. She referred me to a website to download it from an online site. I told her I don’t have a computer. It would be easier if they can send me something in writing and this lady told me that they don’t. She asked- “and you come to us after two years? What have you been doing in the meantime? “And from then on she was very rude and she transferred me to another lady that was worse! I do not need this! And the fridge is very noisy. I’ll never buy Whirlpool again.

BEWARE THE TEMP CAN BE 25 degrees off high and 25 deg lower and Whirlpool says that is within specifications. My oven temp was set at 350 and nothing was cooked... After 7 repair calls with their certified repair companies (the 2 worst repair companies that I have ever used) I was told that if you set your oven at 350 that if it stays in between 325 and 375 that Whirlpool claims that it is working fine and will not do anything. I called and talked to customer service and asked the lady that if you set your oven at 350 should it stay within a few degrees of that and she said YES.The people that work at Whirlpool do not even know what kind of junk that their company is selling. I asked to return it and get a more expensive model hoping that it would work better but they said that they sell ovens and do not buy them. Be sure to get in writing from your sales person that your oven will constantly hold the temp within a few degrees. I tried to do the Whirlpool survey but after 11 attempts they said that there was errors in receiving and they did not get it. If you buy Whirlpool then you did not ask the right questions. I WILL NEVER BUY Whirlpool again (unfortunately I have a Whirlpool dishwasher and refrigerator that are not much better) and if you do you will say the same things and be out Thousands like I am.

I bought this washer (model WTW7800XW) on 12/23/2010. Never happy with its performance from the beginning. Within the first 18 months, the lid hinge completely rusted and broke. The repairman stated that the hinges and glass lid would need to be replaced at a cost of over $400. We paid $899 for the washer. Instead of paying that much, not knowing if it would only last another 18 months, we removed both hinges and removed the lid manually to use the washer. After complaining to Whirlpool about the problem, they thanked me for the info so they could use it for the future. The latest problem to arise is the light inside the washer. The mount for the light was made of steel and has completely rusted away, so the light is just hanging inside the washer. Whirlpool needs to step up and resolve the issue with an extended warranty for these machines.

We have had this Cabrio washer/dryer pair for 8 years now. I didnt want to buy a front loader at the time since they were relatively new and was afraid to roll the dice. We saw the ads for this pair, the washer was the largest top loader at the time and didnt have the agitator (which I liked) so we bought them from Best Buy. I purchased the extended service plan (thank God) because we started having issues within the first month. First was the dryer, it was making a funny squeaking noise. We called to have it looked at and the tech said the drum was out of round. He ordered a new one and it showed up almost oblong. Returned it and got a second (same thing). We straightened it out and put it in. Two weeks later the control panel went out. Repaired it. Then the washer started. In the first 3 years of owning these we had called to repair the washer 4 times and the dryer 4 times. We could have got them replaced after the 5th call. Of course we had replaced all the faulty stuff and the pair settled down for 2 years.Now I have had to repair the washers control panel myself, the dryer sounds like it is coming apart and sometimes runs for hours, and now the washer cant wash in any cycle but delicate because the drum bangs around and cant self balance any more. What junk!!! I know people that have purchased low end machines and have had no issues for decades, maybe a random belt or something simple. I wouldnt buy another Whirlpool set if they were the last manufacturer on the planet. They should be ashamed that they didnt recall these things for all the problems they had.

Apparently the planned obsolescence period for Whirlpool ovens and microwaves is 11 years. Last month, we had to get the oven repaired, and now the microwave has stopped heating. Coincidence??

I purchased a Whirlpool oven and stove from hhgregg. The refrigerator is at best OK. The stovetop is easily scratched and looks horrendous after just a few months. Cooking controls are far too high for slow cooking. Customer service is terrible. Avoid, purchase another brand. You will be much more satisfied.

First three months, the main water gasket broke. Thank you for lots of water all over the kitchen. I pulled the washer out to inspect the cause, wanted to see if it was house plumbing or dishwasher. The hose was hanging off the bottom of the machine. During the 45-minute call, I got in my car and drove to plumbing supply and applied a new hose clamp. The next day, a free service call, the repairman said it was the second one this week, Thats just what I would have done, but would not put the machine back. (void the warranty, finish work, etc...not sure how he would have serviced the machine if I did not pull it out for him). A few months later the wheels on the top shelves give way/fall off the rack, so we have those replaced. As soon as one is replaced, the other side falls off... Now, approximately 14 months into installation, the dishwasher does not work. The control panel is flashing and will not start. What a runaround with KitchenAid. We were told there was a recall on the hose clamp (we never got one). We cannot have the control panel worked on until the hose clamp is certified... That will take a week. Then we can call back... What a hassle. We bought this expensive product on good reviews. We are most disappointed. There is very little concern for making the product good. Its incredible that so much can go wrong in such a short time of limited use. Once/day... The hose clamp is just poor engineering. The rest is terrible quality and support

Dont even consider a Cabrio top loading washer. Wastes your time, money and insults your intelligence. I never use the deep water cycle but boy the machine does! Ive had loads that have taken hours to finish on the quick setting! Thanks Whirlpool.

The clock-timer went out. Appliance is only 1yr. 6mo. old. I CONSIDER THIS STILL A NEW APPLIANCE. This is the 2nd Whirlpool appliance, I bought a Whirlpool washer & dryer. The washer went after 2yrs. use. I bought a Kenmore used washer and it still works. I paid cash for the stove. It was bought at a Sears outlet in Cudahy, WI for $398.58 total with the one year warranty. I really have not gotten the use of the price. I guarantee you (this company) I will NEVER buy another Whirlpool appliance again. TOO BAD YOU COULD NOT RETURN A PARTIAL OF THIS MONEY TOO ME!!!!! I have a Sears repairman coming today 8-3-13 costing me $75.00 just to walk in the door.

My Whirlpool microwave has been great. Just the right size for my family, with enough settings that it wasnt complicated to use. I found it was very useful with different recipes that I liked to make. I always used it whenever possible to cut down on my cooking time because time is something we dont seem to have enough of. I have baked a lot of different items in my microwave, chickens, all kind of casseroles, cakes. You can even scramble eggs in this one!! It keeps dishes warm until you decide to serve it which is a plus because all microwaves do not have this option. I believe you will enjoy it too!

I purchased my Cabrio washer and dryer 4 years ago, my dryer doesnt dry completely, I have to do 2 to 3 cycles to dry. My washer has an f51 code and I have problems unlocking the lid and it takes 2 to 3 hours to wash. This is ridiculous and it causing my electric bill to spike. Is there a recall on the Cabrio?

Purchased a Whirlpool Cabrio WTW7340XW2 washer approx 2 years ago. The machine runs so loud on the spin cycle you cant have a phone conversation or hear the TV over it and is leaking grease from the bottom. My mistake to not purchase the extended warranty but you would think a machine would last more than 2 years. I contacted Whirlpool online and by mail and they do not stand behind their product. I did contact a local repair shop and by our phone conversation was told it would be approx 300-350 to fix it and Im not putting that kind of money into a repair. Just want to let consumers know this machine is junk and spend your money on quality appliances, not Whirljunkpool.

I purchased this Whirlpool Gold Series Refrigerator WRF990SLAMCO in 2012 and it cost me $2400.00 from Lowes. Worst purchase I ever made!!! I will never again purchase or recommend a Whirlpool product. I paid for extended service agreement from Lowes. Before the first year was over, ice was forming on the inside roof of the refrigerator and the whole cooling system/grid needed to be replaced. Then the cooling system went out, followed by the ice maker (PS the ice bucket container was rusted within the first year), then the whole electrical panel on the front of the refrigerator where the ice/water dispenser is.For the last three weeks I have had water leaking out of the top of the refrigerator adjacent to the water filter. My home warranty wont cover. It is a $400.00 repair to replace the circuit that attaches from the water filter. I called Whirlpool 2/14/2017 to complain about the product. She tells me that there havent been any complaints logged about the refrigerator. Seriously??? Read your reviews! The gal on the phone offered a discount to purchase a NEW PRODUCT! Are you serious??? Take my advice. DO NOT BUY WHIRLPOOL. They do not care about their customers or creating a well made USA product. Ill buy foreign next time!

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

I never knew an appliance could be manufactured as poorly as my brand-new, expensive, side-by-side whirlpool refrigerator. Within the first year, the icemaker line malfunction because of a fan problem, causing the line to freeze, break, and leak water everywhere. The ice maker stopped working. Everything on the top shelf In the refrigerator freezes. Everything on the bottom shelf stays warm. The motor is so loud and can be heard of rooms away. It is less than two years old now, and I am sincerely considering buying a new refrigerator altogether.

Our Cabrio washer often ties clothes into (unwashed/still dirty) knots. They are so bad that it takes several minutes to untangle and then the load has to be rewashed. It also has to be set for hot water when you want cold, and vice-versa. I am unable to do that for the rinse cycle, so all our clothes are rinsed in hot water. It doesnt even get the clothes clean, when it doesnt tie them up. Ive gotten used to it sounding like the space shuttle taking off and managed to shut off most of the annoying beeps. The dryer is almost as bad, it seems to take a long time to dry clothes, and they come out very wrinkled, even on the wrinkle guard. The finish isnt even good on either one. It scratches very easily, and scratches start to rust almost immediately. This is quite possibly the worst piece of junk my family has ever owned, except maybe for an unfortunate experience with a 77 Dodge Aspen. We bought this set thinking we were paying enough that we were getting the best. Never again!

I bought a Whirlpool Dishwasher, Model No. GU3600XTVY in July 2010 for $844.30. In August 2011, it failed to clean dishes. The repairman said it needed a new heating element and computer board which costs $319.92. Today, he installed the new parts and it still wont heat the water! Now he wants to take it in to the shop to check the wiring.My previous Dishwasher was a low quality builder-installed GE that lasted 16 years without repair. If we Americans accept that 1 year is an acceptable life span for consumer products, we will continue to have this type of trash sold to us. Made in America is now the product you dont want to buy.

Every time I wash clothes, I get a terrible odor that permeates my home. Ive put in afresh to rid the problem. Ive had a technician take it apart to clean the filter & hose. Nothing helps!! My clothes come out smelling like the sewer. I called the company, and the person I talked to had no real solutions either. Im MAD! What are you planning to do about my stinking problem? Im washing clothes right now & have to have all doors open & fans on high!!!

My Whirlpool refrigerator, a side by side refrigerator, doesnt stay cold. Now it is 60 inside and my ice is melting but temp says it is 40 in freezer. It is only little over a year old and warranty is no longer good. Hard to believe it didnt last any longer. I paid an expensive price for it. Now I have to have a repair man come and fix it.

They really dont make them like they use to, do they? This Whirlpool Cabrio aka Caprio has given us problems for the past 3 years, weve owned it for 5 years. It doesnt matter how much, or how little clothing you put in this washer machine. It will start going NUTS, Thudding, Banging against the inside of itself, completely out of whack, and then it will show a UL where the time is shown. Every time we do laundry this happens, and we have to stick our hands in the hot water and reorganize the clothes, and pull more and more clothes out till theres only about 3 items of clothing left! This washer is GARBAGE! I advise people to keep away from it. The washer we had in the past lasted us years upon years. These washers of now in days are Crap Garbage. Keep the fancy tech look, and give me the old fashion Knobs ANY DAY! Whirlpool brand is Not what it once was.

Both the washer and dryer make terrible screeching noise. The dryer only dries on time drying. The store I bought them from have been here over 7 times too fix them. They still are not fixed. Just a terrible experience with this set from day one, load one.

lD and UL codes are displaying. The UL code displays when the load is even and also displays UL load when I take all clothes out of washer. How could the load be uneven if there are no clothes in? I have had four different issues with this washer. I have started use on this washer in Aug. 2008 and there have been already three major repairs. I am a very dissatisfied customer. I dont know if I should spend more money on washer repairs or just buy a new washer. Please help.

Ive had nothing but problems with the Whirlpool Cabrio washing machine and dryer. The motherboard has been replaced three times, once on the dryer and twice on the washing machine. The inside of the washing machine is going to fall apart because of the rust at the bleach holder. I saw some of the complaints. Is there any way we (consumers) can sue Whirlpool for selling defective units? We are from all across America and there is no way we should all have the same complaint. The stores that are selling us these items should be held accountable. Also the only thing Im getting from them is, Theres nothing we can do. PLEASE DO NOT BUT WHIRLPOOL WASHERS AND DRYERS!!!!

Our whirlpool gas range has a defect - the material around the control panel is peeling and flaking; it is not possible to clean it and it is likely going to get into our food. It has not been cleaned with anything harsh - I use warm soapy water or stainless steel cleaner. I use the same thing on my other appliances and they look fine. I am waiting for a tech to come and look at it but after reading other complaints I fear that they are going to say it is cosmetic and it is not covered. Sadly, we can no longer wipe the control panel if it is dirty because the stainless steel is flaking off and it gets all over the burners and I am concerned it will get into our food. I am willing to bet the paint that is flaking off is not approved for consumption.I wish I had our old Frigidaire Gallery Series range back. I regret replacing it. Whirlpool was not helpful. They told me to contact the place I purchased it. The place I purchased it said it is a manufacturers defect. Someone suggested painting it with stainless steel colored spray paint which sounds like it is going to look awful. The new panel is $148 but it will need to be installed and if there is a defect how often will I have to replace it? I am very disappointed.

I have been a dedicated Whirlpool customer for 50 years. I purchased my new, Cabrio washer and dryer in 2011. The dryer works fine. The washer does not. It ties everything in knots. Most everything comes out in one large, wrinkled lump. When washing sheets, it wraps the whole load in a soaking wet, fitted sheet bubble. You cannot wash one item by itself, because it will become unbalanced and shutdown. I will say that I havent had any repairs yet, but I have a feeling, its only a matter of time. I have decided to buy a new washer, but it will not be a Whirlpool.

I have always had Whirlpool Everything - not anymore!!!! I purchased a water saver washer that I am very unhappy with - it does not get the clothes clean. I have to put it on an extra rinse (water saver?) to get the soap out. I use the Tide for HE washers. I cannot wash a large load in it - directions say I can. Anything too heavy or bulky will not spin out well. Will bounce all over the place. From now on I will switch to another brand. They push so hard to buy a warranty because they know you will have trouble! Should have read the reviews!!

I bought refrigerator in Feb 2017. Within 18 months internal surface got crack, contacted customer care but I would say Whirlpool India customer care department is worst across world, no courtesy towards customers, contacted them over phone very bad attitude, no response on email. Product quality is worst, its better to buy Indian brands. They are much better in quality & service. Totally dissatisfied with Whirlpool approach, at the end Whirlpool customer care is not at all bothered.

The Worst experience with Gold Series Mod WRF 757SDEM01. Purchased from Best Buy June 2016. $2215.00. Within 6 months The interior light began going dark within 6 months. Our very reputable warranty repair service ordered a part that did not repair it. Was only temporary. They did figure out that the circuit board was bad and promptly took care of our problem. Next I kept noticing water appearing on our wood flooring. Let it go because it only appeared sporadically. Called Whirlpool only to find out they switched to a warranty repair service that was inept and inexperienced. Said he could fix it. Blamed it on a freeze-over so I let floor dry up then re-started and refilled. Thought he did fix it cause it made sense. When reassembling he broke to upper freezer try glide. Then 3-4 weeks later I notice one morning water again on my wood floor. The dripping had been running beneath the wood slats and had seeped up through the joints. Now the flooring wood has swollen and will need to be replaced because of this. This is the second time I had to unload all food and store at neighbors and give away. Extremely poor engineering designs as each time the ice dispenser is used, nothing prevents ice from flying out onto the floor ever since day one. Same with water. The release does not shut down to prevent water or ice from pouring out onto the floor when removing any size cup. The refridge doors must both be opened to use the lower level drawer. Loses much cooling with having to always open both. Next, weve come home MANY times with the left refridge door partially open because of the difficulty of the mechanism to secure at closing. This happens to us 5 times a week for three years-honestly!. This was the only refridge we could find that would fit our opening in a 20-yr-old home. The fridge is so heavy one man cant pull it out of its opening. Only 2 very small wheels in front and skids in rear stick due to weight. Weve confirmed this is not a spigot leak from the ice maker. Finally (but probably not) the ice container allow much air in because of having to open the left door that your ice is always melted together plus it too small for a family of two and ice must be purchased when entertaining. And to top it off, the human that took the warranty call this time is foreign and my wife could not get them to get our last name spelled correctly nor the phone number correct after constantly repeating it. This unit and model is an absolute lemon. Im going out today to find another unnecessary $2500.00 to buy another.

The knobs on the Whirlpool gas stove model Super Capacity 465 AccuBake system are easily confusing and dangerous. If the knob is turned in the wrong direction when intending to turn the burner off, it turns to a very low setting which is although nice for simmering, it is very easy for it to be mistaken as the off position and leaves only the gas leaking if the smell is not noticed in time.

Whirlpool Cabrio top loader washer - I am writing to really complain about a washer I bought there at Metro. The people were great BUT this washer has been a REAL DISAPPOINTMENT!!! It is only 4 years old and I have had to have them come and replace the top of the machine. It has rusted around where you put the bleach, the soap. It leaks underneath the machine, its rusting on the bottom of the machine horribly. SO DISAPPOINTED!!! We bought all WHIRLPOOL products - washer and dryer, stove, microwave, dishwasher.What is it with these things? They rust so easy. I had a washer before this one for 14 years and it never did this. I guess things are not made with the same quality as years ago, but I will not ever spend my hard earned money on WHIRLPOOL AGAIN!!! I guess I will have to put up with this machine till I can afford to buy something else. VERY DISAPPOINTED CUSTOMER!!!

We have a large family so when we needed a new refrigerator we found this very large unit (Whirlpool 32 cu). About this unit, its not really all that wide, but it is very deep. Lowes didnt have a model on the floor but we went by photos. Also the salesman showed us a smaller version of this unit and we were impressed with the design. However unlike the unit we saw the shelves arent adjustable. They are preset. Also the ice maker on top is very small and makes ice very slowly. The freezer section ice maker is much larger. The main complaint I have with that is unless you push the tray all the way to the back ice can drop behind the tray and fall down causing the freezer door not to always close properly, leaving you with semi defrosted food. Whoever designed this refrigerator was an idiot. All issues are really related to design flaws. This is a very expensive refrigerator. I expected a great unit and got a piece of crap instead. Stay away from this model at all cost. It would be smarter to buy 2 refrigerators instead if you have the room. This model will give you nothing but a headache and grief.This is our story about our experience. This all took place within 1 year. We bought it at Lowes. They were wonderful when it came to taking care of us when it was within the stores’ warranty. They really tried to help us. Once their warranty ran out they put us in touch with our new repairmen. Lowes did tell us that one other man bought the same unit and he was up to refrigerator # 15. Like I said, this unit is crap. Our first unit was delivered with a huge dent in the door. They took it back (lucky for us we have 2 other refrigerators).Second unit arrived in store also badly dented. They didnt bother to deliver that unit. Third unit arrives at store but back area around motor all dented up. They order a 4th unit. This unit wasnt dented up so they delivered it. However doors were very off and wouldnt line up so it didnt close properly. A 5th unit was ordered and same issue with the doors. A 6th unit ordered and they called telling me that it was all dented up and needed to order a new unit. Our 7th unit arrived and in 3 days started making funny sounds. Dual ice makers stopped working and inside refrigerator is was very warm. Lowes ordered #8. This unit the freezer doors werent lining up so #9 was ordered. This time everything seemed to line up, no dents however by the third month it started making a funny sound. Dual ice makers stopped working. Warm inside the refrigerator section. Lowes sent out a repair man. He explained a design flaw was not enough insulation around the fan so it was icing up. That was replaced and it was working nicely for 4 months. Same issues with fan icing up, the noise and no ice. The repair man came out again and mentioned what was kind of a recall with the unit. The control panel in the back of the refrigerator was wrong and needed the correct one to be put in. That was done. He told us that we shouldnt have any more issues with it.Same thing again. Same symptoms, same results...we had to throw out hundreds of dollars worth of food. (I just put in an entire prime filet mignon I planned for a special dinner and had to throw it out. OUCH!) Awaiting for the repair man, again. He will be out in 5 more days. Im sure it will be a new issue, a new brand new fix and it will work for a few weeks to months and we will be calling him again.

We just purchased a new fridge - September 2021 -- Whirlpool side by side. Why is just okay? It is a loud refrigerator. A roaring sound is pretty constant. The ice tray in the door has no recessed tray ... so water and melting ice just follow down the front of the door and onto the floor. Two days after purchase we went back to Lowes to return this fridge ... but all the other refrigerators do not have a recessed ice tray. And since they are not plugged in ... who knows if they roar.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

On its 1st year, the water pump went out. It cost $200.00 to replace it. On its 2nd year, the circuit board went out, and it took $300.00+ to replace it. On its 5th year, the bearings went out and cost $250.00 to replace it. I bought this for $900.00, and I already have paid $750.00 plus the price of purchase which makes this washer $1,600.00. Whirlpool should compensate all of us who have worked hard and have purchased this product! I will never purchase from Whirlpool again. I can’t afford them. I should get a refund from Whirlpool. Don’t they care? Email me for these problems at **. I am so dissatisfied with this product.

I purchased a new water heater in August 2013. The pilot light started going out in October/November of 2013. After calling the Tech Support phone number, (877) 817-6750, I was advised to clean the burner screen. First this is very difficult to do because the burner screen is underneath the water heater and almost impossible to access. Second the closet the water heater is in did not show any signs of debris that could clog the burner screen. I did as they recommended. Several calls, and several weeks later, they finally authorized a technician to come and service water heater. He performed a cleaning even though he couldnt find anything to clean; and he replaced the control module. The new control module worked through the spring and summer seasons and then I started having issues again in the fall, late October. Started calling the same phone number and was told again to clean the burner screen. I convinced them to send out the technician again. The A and E Factory technician came out and only cleaned the burner screen and left before I had a chance to get home. This happened several times and I called Whirlpool every time. The next A and E technician told me to try changing out the draft vent chimney to a different size, which I did. Problem happened Again! I finally asked for another plumber and they sent me 3 names of their authorized plumbers. I called Phil, Philco Plumbing. He told me that I needed to have more ventilation, so I added more ventilation, even though I later found documentation stating I already had more than what was required by the manufacturer. Again, a week later, started having problems. Call back and asked to have my personal plumber come out. This time the rep told me that I have always been free to choose any plumber I wish (why wasnt I given that option the first 10 times I called?). My plumber came out and replaced the control module and the thermocouple, but wasnt convinced that these were faulty parts, he honestly couldnt figure out why I am having this problem, but it was worth a try. That lasted about 1 week and now I am having the problem again!!Whirlpool will FINALLY authorize a new water heater, but they will not authorize installation for the new water heater. I have already spent money on recommended repairs that have not worked. I have taken 15+ hours off of work to watch plumbers do nothing that has rectified my problems. And now Whirlpool wants me to deal with installing the unit myself, OR pay to have it installed! They say they wont cover installation because I purchased it more than 1 year ago. They seem to be missing the fact that I have had trouble with it the ENTIRE time I have owned it!This Flame lock system is garbage. I found on Consumer Affairs that a few years ago a class-action lawsuit settled, dealing with the same issues. I think it is time for another round! I KNOW that I am not the only one dealing with this problem because the plumbers I had out all had similar complaints from many of their clients. Whirlpool wont fess up to the problem, but the problem is real.

Whirlpool model WRV986FDEM Purchased May 31, 2017 from Lowes. Cost: 2,638.10 including 229.97 for the 5 year extended warranty. We’ve experienced four failures in the nearly four years we’ve owned this lemon. The first failure occurred within the one year manufacturer’s warranty period. The three failures since then have been fairly close together. Control boards and mechanical parts have been replaced. We are now waiting for a “made to order” part, with no scheduled delivery date. When I pressed Lowe’s on the reliability of this fridge, I was told that if four failures occur during the extended warranty period, they would give us a replacement. Considering the delays in repairs and frequency of failures, this is unacceptable. Do Lowes and Whirlpool expect their customers to just suck it up and do without a refrigerator for months while we wait? The warranty is worthless without prompt problem resolution. Whatever happened to real customer service?

Recently bought and had a Whirlpool Cabrio Washer (from Orvilles appliances) installed in my home. The very first day I hated it. Worst purchase I have ever made. I spent over an hour picking hair out of my clothes, and hair was also stuck in the crevices of the drum. This is the very worst machine and company I ever had to deal with. They told me, Too bad. Since there was no mechanical problem there is nothing they will do. I will never deal with either of these companies again. I cant wait to see what the hair build up will do to the machine itself, Had it less than a week.

I have had my Whirlpool Cabrio washing machine for 14 years. I feel this is very dependable and cleans my clothes efficiently. I love the large stainless steel tub without the agitator. I can fit a king size comforter in the machine. The only problem I had with it was to clean the lint out which I would assume would have to be done to any machine that is used every other day for 14 years. Love it!

Bought this washer and dryer on sale at HD. The washer hasnt worked from the beginning. The clothes dont get wet because its an HE. I have to add buckets of water to even get the clothes wet enough to wash. The clothes come out with a residue on them. We use liquid HE detergent. It appears Im having the same problem as the majority of posters here. I will NEVER buy another Whirlpool appliance. There should be a class action suit to get Whirlpool to respond.

When washing towels or a blanket or quilt, anything substantial it wont spin the water out of the laundry. This washer is only 5 months old.

Whirlpool is not what it was before. I got this set with new house... They are very poor construction. They are not even close what I have before the LG. After 6 months I begin to have problems with the dryer... Technician come two time to fix the problems. Quality of washing is OK though... That going to be the last time I got Whirlpool products. For sure.

My wife and I bought a Whirlpool Cabrio washer and dryer set in 2011 and now the washer has an error code of F7 E5. I spoke with an appliance guy and he says that it is going to cost up to $450 to repair it. The wash cycle does nothing, it just sits there and then it goes to the next cycle. I have grown up in a household that had washing machines that lasted many years. This is a joke. Why am I having to buy a new washer in 3 years? I dont understand. Whirlpool knows that this is a problem and they should step up and do a recall or some kind of discount towards a new machine. This is ridiculous.

I am 72 years old and this Whirlpool Energy Star HE Washing Machine is just useless. It does not clean clothes properly. It always leaves a stinky washing machine smell which never goes away despite no matter what you do. A completely useless, faulty washing machine! Never ever buy a Whirlpool HE washing machine! Some websites say that you need to buy a washer fan at a cost of $69.99 and attach it to the back of your washing machine as this is the only way you can get rid of the smell. Who has that kind of money? Why is this fan not already included in this washing machine if Whirlpool is aware of the smelly washing machine/smelly clothes problem? This is such a joke! We would like to be reimbursed for our deficient Whirlpool Washing Machine or at the very least, have a recall of this inefficient, poorly designed washing machine. Report them to the Better Business Bureau and anyone else you think can resolve this problem - thanks!! - Unhappy camper

I went from an HE front loader to an HE top loader (Whirlpool Cabrio WTW7000DW0) due to the risk of mildew with the front loader. Im not the only one doing laundry and if someone else does it, it always seems that they shut the door when empty, contributing to moisture and mold that needed to be cleaned out of the gaskets. I am so unhappy with my top loader HE washer. When I stop the machine and look, I always see my laundry half covered with dingy water, sometimes part of it still dry at the top and it is disgusting. I frequently have to rewash loads due to detergent getting trapped in folds or pockets created that hold on to dirt and lint, even being careful with the detergent amount. I run the washer now every time with settings of deep water, extra rinse, heavy load and presoak with instructions, with settings taped to the top for others.At almost 1 1/2 hours each load, we just cant keep up. The laundry still forms pockets and sheets form a giant tent over the entire load that has to be unraveled at the end of the cycle and wound so tight it had no chance of rinsing. I had to get a repair person out because it got out of balance and he had a small hand-held computer to enter a code to rebalance it. When we discussed the issues I was having, he was ready for everything I was doing wrong. He told me I can not wash blankets or large items (I thought I was buying large capacity with such an enormous drum). He told me they have caught people adding water with a bucket during cycles and that the washer software can tell them if people are trying to work around the system which voids the warranty.Apparently, this is a common complaint he blames on the government wanting high efficiency so they make the numbers look good, sacrificing the ability of the washer to perform at what a consumer expects. I have never seen the water in my drum higher than a couple inches and the drum is HUGE, but never used to capacity. He told me his wife demanded they get a commercial washer because she was so angry about how poorly it cleaned. I feel so scammed and I wish I could have my old agitator back. $100 for the repair call, $150 for the code to be put in and Im on warning that they will see if I try to add water, run out of balance or dont comply with any reason they can void the warranty by just checking the data the washer is collecting on us.

My elderly parents had everything they own destroyed in Hurricane Sandy. After rebuilding their home, the new Whirlpool washing machine was broken. Whirlpool refused to disconnect and remove the machine that was obviously broken before it arrived. This is something that no one should have to go through. It is appalling and bad business. Through the kindness of friends, we had several male friends help with the removal. Truly shocking, that this is how Whirlpool handled this situation.

I have had a Whirlpool washer for less than 1 year and have had it serviced over 7 times with drain problems - code A10 being displayed. Have not been able to resolve the problem with neither the dealer nor the manufacturer. What a lemon!

Ours is a glass top & has 2 dual burners & we are very pleased with that feature. The oven however takes quite long to preheat & the alert sounds are so weak you can barely hear them. It was a rapid purchase on a sale item. I wish we had shopped a bit more.

We bought a new Whirlpool refrigerator about three years ago. Because of space, we had to purchase one with a top freezer and also with no ice maker. First of all we didnt realize it was much deeper than our old Kenmore so it stuck out further into the kitchen space. That was not that big of an issue. At first everything ran great including the top freezer compartment, or so we thought. Then we noticed that when we had ice cream in the freezer and put water in ice cube trays to freeze, the ice cream would get very very soft. This continued to the point that now anytime I put water in there to freeze ice cubes I have to turn up the temperature to keep the ice cream frozen. Once the ice cubes are froze, there is no problem, but they take at least six hours to freeze. Then one day when a young child slammed the refrigerator door closed, the freezer door popped open about an eighth of an inch and then closed again. So, I tried it. Anytime you close the refrigerator door a little too hard the freezer door pops open. I then tried the dollar bill test to check the strength of the seal. The bill pulled right out of the door with very little effort. So, is the problem bad seals, bad design, or bad quality control, or what. How can I be assured that the frozen foods in the freezer are being frozen as solid as they should be. I know they dont freeze solid enough in the freezer door. I will eventually dump this refrigerator and go get another Frigidaire. If we have to get one with a bottom freezer, we will just have to rearrange our kitchen to accommodate it. But, having to turn the temp up and down every day is ridiculous. I have had issues with food close to the walls in all refrigerators slightly freeze, but never had an issue with keeping things cold enough. I will never buy another Whirlpool refrigerator, stove, or anything else for that matter. I have always had good luck with Frigidaire, so I will stick with what I know works.

I purchased the Cabrio washer during the black Friday sale. The washer was a pretty slate gray. I loved the color and the fact it was a Whirlpool, which I thought meant quality. It was expensive but we were updating our appliances as our 10 year plus washer needed replacing. Big mistake. This washer is terrible. It keeps me stressed. There is not enough water to clean the clothes, my husbands white underwear is always dingy and dirty looking. The sheets are dirty and smells. I try putting bleach on whites before washing and the whites still come out with underarm stains. I tried all the recommendations to no avail. This machine is awful. This was a big financial mistake. As soon as I am able this machine is gone. Will go back to the agitator in the middle, and NOT a Whirlpool. I DO NOT recommend this machine unless you want something pretty because this is NOT a washing machine.

I have owned this Whirlpool Cabrio machine and dryer for almost 5 years. It has been a nightmare. I am forever getting it fix. Now its the notorious LD light, not draining, and it has actually drained, and the company I bought it from does not repair them due to so many problems. Got a plumber to look at it and got it to work.. This is after the company came, charged me 130.00 to tell me they dont repair it. I bought this machine because it was large and I have a big family, energy saver (no, it did not save as much as they claimed) and uses less water. The dryer is wonderful. But the 1900.00 I paid for them was not worth the price. I now have to go up and down my cellar stairs 6 times per wash to stop it, shake the hose, and restart it. A load of laundry takes close to 3 hours due to starting it over. I am gonna buy a Maytag which I use to have and take this to the junkyard. Thanks a ton, Whirlpool and I read all comments and they are ALL true.

My NEW Whirlpool top loader just stopped working. I bought it in June 2015. The extended warranty I purchased ended at the end of June of this year. Guess what happened a few weeks later? The thing died. Seems totally fishy! My parents washing machine lasted 20 years. Why does this one die weeks after the warranty expired?

I purchased the Whirlpool washer and dryer three years ago and I absolutely wish that I hadnt. After three years of use, the bearings on the tub are shot. I need to replace them but it will cost $400.00 to repair. This is the second time that this machine is for repair. I am going to dispose this machine and purchase a new model other than Whirlpool. The overall performance is poor and not as advertised. It does not use enough water and does not wash clothes well enough. At times, you can see that the water never reached parts of the garments. I am totally disappointed in its value and quality.

Bought unit from Lowes in july 2017. Shortly after icicles started forming on the roof of the freezer near where the door & frame meet. Called authorized service repair company to have them check out. Tech knew right away what was wrong. Appears Whirlpool has the parts made in China & then assembled in the USA. China has overfilled the freezer door with insulation warping the door. This makes the door seal sag on the bottom & pull away on the right side. No way to repair. Was told they need to order a new freezer door.Weeks later I get a call that Whirlpool cannot get a door replacement!!! Said they will give Lowes a store credit. The floor model at Lowes has the same defect. When Lowes ordered a replacement unit they opened the packing & found that this unit has the same defect. I am replacing with a Frigidaire! Where is the quality control at Whirlpool. Anyone at Whirlpool who puts these units together could not help but see this defect - but ignores it & ships it out anyway. Thats what you get from farming stuff out to China. No excuse on Whirlpools part. Maybe Trump can save Whirlpool.

I purchased dishwasher model #GU2800XTVT0 in May of 2009. Today, it leaked water all over and damaged my floor. My husband pulled the dishwasher out of the cabinet and found that the motor had fallen off. It did not have a bracket to hold it in place and worked loose, which then disconnected a hose. I called the customer service but they wont do anything because it is beyond the 12 month warranty. It only lasted slightly more than two years. This is obviously a manufacturing defect and we were just unlucky enough that it failed after the warranty had expired. The most ironic thing is that my husband worked for Whirlpool for 20 years. There is no loyalty here.

I have a double door bottom freezer refrigerator manufactured by whirlpool. It is less than 2 years old and is an absolute piece of garbage! In less than a year the noise started, then the freezer became a refrigerator and my frozen stuff melted. I had a local technician come in and he fixed it but he indicated that the fix would not likely correct the problem. Sure enough, about 6 months later the same problem started all over again. Nowadays one is never sure where a product is manufactured. However, if Whirlpool had their products made by chimpanzees in the jungle they would be better than the pieces of trash they are now selling!

Bought this model from Bad Boy in 2006 and just after the warranty ended the problems began. We kept getting the F1 error code so with a little internet research we found it was a known problem with Whirlpool. I contacted them and was told they knew nothing about this issue being nationwide, however I emailed them copies of the complaints and responses. They sent out a technician who had to replace the motherboard free of charge. Next issue was a loud noise coming from washer sounding like a jet plane taking off. Hubby ripped machine apart to find the bearings blown apart and in tiny pieces. We ordered new ones and also found that when the new ones arrived they came with a tube of grease and a sealer to use so water would not get in later and cause more problems. Funny there was no sealer on the original bearings.Next the lid lock finally failed, ordered a new one but did NOT install it back into the machine, now it sits beside the machine. In case it fails again we will have total access to the laundry this time. Finally the UL error code keeps coming up. I refuse to put any more money into this machine again so I am allowing hubby to fix it if he chooses, whichever way he wants as long as no money is involved. So right now we have bungee cords holding the suspension rods tight to help with the uneven load code coming up all the time. Personal thoughts - DO NOT BUY WHIRLPOOL washer/dryers. They are crap and the company just does not care and they try to lie their way out of repairs if people have not done their homework.

After 7 calls to Whirlpool and 3 service calls, we still have white detergent stains on all our clothes. Today Whirlpool told us we needed to put one item at a time into the machine. Not only that, but pants needed to be loaded waist band up and gently placed; Shirts, collars up; socks toes down, etc. etc. Are these folks at Whirlpool serious?? So today, we called them back - still streaks. The folks at Whirlpool want us to take and send them pictures of our clothes. This is ridiculous.

I purchased my Whirlpool refrigerator from Whirlpool guest system (online) in 2010 for around $1,160. Recently, it stopped dispensing water from the dispenser. I called the Whirlpool certified A&E serviceman to repair the dispenser. He concluded that the water line is frozen inside the door. He also stated that such issues with the door shouldnt happen for at least 10 years. He gave me a bill of $920 to replace the door. I called Whirlpool and they declined to pay for the repair as it is out of warranty. I feel that they sold me a faulty refrigerator and they should pay for this expensive repair. With $920, I can probably pay for a new refrigerator (not Whirlpool, of course). I am completely disappointed by Whirlpools customer service and poor quality of their product. This company, I believe, is more interested in selling crappy products, make profit and not provide good customer service. Shame on you!

We bought this 26 cu ft fridge from Nebraska Furniture Mart in April 2017. In November stopped making ice. Was repaired. Now it’s not working again. Multiple enquirers shows this is a common problem with this fridges. I’m debating whether it’s worth the effort to repair it or just put in junkyard. WORTHLESS piece of shiny metal.

As very happy owners of a previous model of this fridge freezer when ours needed replacing, we went direct to Whirlpool and bought the latest model. What a mistake! Other comments on this site are so accurate if only we had seen them before. A kitchen floor covered in ice mush (cubes seem out of the question) and tepid water from the water dispenser whereas on the previous model it was chilled. Basic functions that the previous model excelled at. Sadly it is also badly designed inside the fridge. We raised these issues with Whirlpool within our first year who merely said sorry you are unhappy and thanks for your comments. Be very wary of Whirlpool products and service.

We bought a Whirlpool washer in 2010. It started making a loud noise on the rinse cycle in 2012. We called Whirlpool. They sent out a repairman from A and E Repair. Was told tub bearing shot, repair over $700.00. Contacted Whirlpool, was told machine out of warranty. After talking to them, they agreed to send parts if we paid labor. Machine lasted less than a year making the same sound again. A and E sent out same thing, bearing gone. Repair cost $997.17, charged us $136.74 service call after 2 minutes to shake the drum and saying same problem. Was told by Whirlpool, no warranty, tough luck.

I have fought with this issue hundreds of times over the last 3 years. My old water heater work fine until it started leaking, I bought a Whirlpool 40 gal gas hot water heater from Lowes. Worked fine for the first month, then this pilot light issue started popping up intermittently. Now the damn thing doesnt want to light at all. I WOULD NEVER BUY ANOTHER WHIRLPOOL PRODUCT THE REST OF MY LIFE, and I will tell everyone I know that WHIRLPOOL Products are not quality products. DO NOT BUY. There have been so many class action lawsuits about this product and Whirlpool keeps on selling this junk. Im so frustrated with WHIRLPOOL customer support I cant think straight. To reduce your headaches in life, do not buy Whirlpool products as they are junk and their customer support is terrible also.

After 22 years, I replaced my Whirlpool, electric, 50 gallon water heater, due to age and it was still working well. Went to Lowe's and they do not carry Whirlpool any longer, so I purchased and installed an A.O. Smith water heater, electric, 50 gallon water heater, model ES12-50R55DV110. Hoping for as good a product now, as I had from my Whirlpool. Also, I installed myself.

We bought a Whirlpool French door fridge model WRF989SDAM00 in 2013 and were impressed by how it looked in our kitchen. Its December 2015 and things have started to go wrong. First the freezer stopped freezing items completely and found out that ice had built up on the cooling tubes inside the rear freezer wall. Had to be taken apart and thawed with a heat gun. Now the freezer freezes on and off and the ice maker is not making ice properly and leaking all over the left side of the fridge. Went to Sears {place of purchase} and we were asked immediately if we had purchased the extended warranty. We hadnt and were told Sears could do nothing and that these newer fridges have a tendency to have trouble within the first couple of years and thats why they recommend the extended warranties. Really a $2500 dollar fridge a couple of years? Had a local appliance repairman look at it and he said the compressor was bad. $500.00 to fix. Boy do I regret buying this thing. These big companies just walk all over us consumers.

Purchased Whirlpool dishwasher and range approximately 16 months ago. Dishwasher must stop in middle of rinse cycle because the dishes always feel filmy and there is an inch or two of water in bottom. Must be bailed out by hand. Piece of garbage. Called Whirlpool and they can get us a service man from 8-4 (who waits an entire day these days) on New Years Eve. Next appointment is following week to examine and will fix (if it is their fault and for a fee). The last two dishwashers I purchased lasted 10 and 7 years respectively. Stay away if you dont want bad equipment, uncooperative service, and aggravation. Range I bought was OK but the oven temperature is always off 10-15 degrees from what it says it is. I honestly wanted to buy American but I feel cheated. Next time Ill try Samsung and see if they give a damn.

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

Whirlpool water heater FG1F5040T3NOV - I noticed that when I was taking a shower, my hot water wasnt working. I went downstairs and the pilot light on my water heater wasnt on. I tried to restart it. The pilot light wouldnt work or relight. I gave up and contacted a plumber. I dont feel I should have to pay for a plumber when its a product flaw!

I purchased a Whirlpool microwave model #WHM3205XVS1 on October 2, 2011. The handle broke off in little pieces and was repaired in March 2012. Handle broke off again in little pieces in September 2012. This will be the 3rd handle that will continue to break in little pieces every 6 months. According to both repair men that were here, this is their comment: No customer abuse, this is a very common problem with this model. After to speaking to 3 people at Whirlpool, I was told by everyone, This is cosmetic problem and we will not fix after the 1 year manufacturers warranty is up. I started with the the first person, went to her supervisor, then went to her supervisor. I am now waiting for a call from a manager although I was told I will continue to get the same answer no matter how far up the chain of command I go. So, I was told that it is okay to have 2 screws sticking out holding the remaining part of the handle that is left, because it is a cosmetic, not a functional problem. I will never stop with Whirlpool. I will call 4 times a day if necessary. I will never purchase another Whirlpool product again! I will tell everyone I know not to purchase one of their products. Be careful. They manufacture products for many other companies, i.e., Sears, Amana, Jenn-Air, and many, many more.

Whirlpool Duet - Steam cycle and sanitize on wash. Dryer is fast and automatic cycles actually work! Have had the washer 4 years and the dryer over 10. We like the Duet Washer because it had a steam cycle and a sanitize cycle plus it has a light inside that helps us see the laundry in our dark room or at night. Also we have been very happy with the cleaning - does a great job and gets the dirtiest clothes clean. The Fan Fresh feature and Delay Start are very handy especially for busy parents who may forget the laundry is in the washer.

I have 2 dishwashers. A stainless Quiet Partner III & a plastic Quiet partner II. The Partner III never gets the glasses completely clean. The cheaper Partner II gets everything clean but has had several service issues.

If you like having to use a funnel to refill plastic water bottles, and enjoy ice splashed all over your kitchen floor then the Whirlpool Gold refrigerator is the model for you. The problem with ice is if you dont have your glass sealed up to the ice dispenser it will shoot ice out over the top of the glass, and even if you DO do that when you try to remove your glass to cut off the ice supply it continues to disperse ice everywhere. TIP: The only way to more efficiently stop ice from spraying all over your wood floor is to do this: When your glass is full of ice, simply open a door on the refrigerator. That IMMEDIATELY stops the flow of ice OR water. Works great, and its the only way to deal with this horrid design flaw in this product....

Whirlpool g2 convect/micro over the stove oven - This top of the line oven is JUNK, KEEP YOUR MONEY-DO NOT BUY THIS JUNK! I have had problem after problem. Starting after only three months. Defected door switch, touch screen, flashing screen, error message. The service repairman and I are on first name bases. Thank goodness for the, out of my pocket warranty which I no longer plan to keep. I NEED A OVEN AND DEFINITELY NOT A WHIRLPOOL.

We have several Whirlpool products in our home currently and have been very satisfied with their performances. We have their fridge, stove/oven, microwave and dishwasher, all of various ages. We purchased them from a local big box building supply company and installed them our self. The installation directions are clear and simply for the average D-I-Yer. We would recommend Whirlpool to everyone shopping for these home appliances.

Whirlpool Refrigerator Model WRX9885IBM01 French Doors - We purchased this $2,000+ dollar refrigerator in December of 2014 and within two weeks of plugging it in, we noticed the freezer drawer was crooked and ice crystals in the freezer compartment. We contacted Whirlpool re the matter and they dispatched a local serviceman. He informed us that the inner lining of the refrigerator was crooked and he contacted Whirlpool. He sent pictures of the crooked drawers and was advised by Whirlpool to adjust the outside door, but nothing could be done for the inside crookedness and that he was to take silicone and seal the refrigerator to prevent air coming in to create the ice... Really? We told him that was merely a Band-Aid to the problems and we wanted a replacement. According to Whirlpool, they can only service our month old refrigerator and cannot replace it.Actually, they cannot even service the defective product they sell, they can only caulk the problem until it comes again. I am not going to stop until everybody in the country buying a refrigerator thinks first about the warranty Whirlpool offers. After reading defective parts, etc., I am amazed they are still in business! We are contacting Lowes to come pick it up! Let them deal with the garbage they are selling!

Whirlpool Du1100xtpb3 dishwasher: The spring on the latch keeps coming off (3 times in two months). The service repair man charged me for replacing the latch when all that was wrong with it was the spring. That being said, now we are fixing it ourselves. For your information, there is a paper in the bottom of the dishwasher that tells you what is wrong by how the lights are flashing. So each time we replace the spring, we have to reprogram it by pushing a sequence of buttons. Still, I cant figure why the spring wont stay on. Help me if you can.

Ive had the WDF510PAY dishwasher for 3 years and the circulation pump broke. To be more specific the impeller inside the circulation pump warped and then basically got lodged because it became oblong and then it wouldnt pump water to the spray arms etc. I bought a new pump because the warranty only last a year. The pump cost around 90 bucks. After not even 1 full year this factory replacement pump failed again. I reviewed other Whirlpool dishwashers more expensive and I found they all have this same junky circulation pump. Im not sure of a better dishwasher but I would never recommend a Whirlpool dishwasher again. They also use the same circulation pump in Maytag and many other brands. Whirlpool or whoever designed and sold this pump to Whirlpool should be tracked down and beaten. Simple products like dishwashers should last more than 3 years. The technology is nothing new. A product should last 10 years at least.

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

I had a 6 year warranty on the new Water heater and about only 4 years into it the tank began leaking. Whirlpool replaced it but of course I was responsible for Parts and labor to replace it. The replacement only lasted just over only 2 years and just outside the total of 6 years from original purchase date on the first. Whirlpool refused to discuss it since it was a few months out of warranty. If someone else has purchased this heater it would have failed at 2 years and they would have had to warranty it anyway. I will never own another Whirlpool appliance because of their substandard products and warranty. I only wish I had reviewed the reviews of others and taken their experiences into consideration and not purchased Whirlpool. I am now out for another heater and reinstallation charges again.

I have clothes that are coming out torn with large holes, especially cotton items. I dont know if it is the washer or dryer.

Because the lid was not thoroughly covered, painted and sealed, it began to rust within first year. When I contacted Whirlpool about this - they were not only rude, but will not support quality issues with their products. They basically said they did not care and even acted like a consumer should expect such things! Actually said because its subjected to high moisture levels. WRONG, I do NOT just expect rust. It only formed due to poor quality paint job and was not cured correctly. My Kenmore washer and dryer both, were 25 years old and had zero rust and still functioned when I replaced them with these Whirlpool. Its frustrating that there are no quality, American made products anymore.

I am the owner of a 4-year-old stainless steel Whirlpool refrigerator, Model GB9SHDXPS02. Yesterday morning, my 5-year-old daughter opened the fridge door to get a snack. The door came crashing down, hit the floor - missing my 21-month-old daughter by less than two feet - the drawer smashed off on impact and flew across the kitchen floor and the contents of the drawer (salad dressings, syrup, condiments, etc) went flying too. Miraculously, no one was hurt. My children were obviously upset and crying, and I was shaken. My laminate floor has a large dent and long scratch from the impact.My fridge door is broken. I cannot get through to Whirlpool Canadas corporate office to speak to anyone. The Whirlpool Canada call center is giving me the runaround. Yesterday I spoke to a supervisor at the call center who advised me that someone from the Corporate Safety Division would phone me within 24 hours - but I have not received a phone call and it has been more than 24 hours. I am noticing a complete disconnect between the gravity of the situation and an appropriate response from Whirlpool. I am a mother of 4 small children - two of which were very nearly killed/badly injured by a faulty refrigerator door. I cant even get a phone call in response. This is a serious safety issue. Im tired of apologies, some real action needs to be taken to ensure this never happens again to any consumer.

Our Whirlpool refrigerator, model MODGI5FSAXVYO, began leaking water from the freezer onto the floor about 3 months ago. We purchased the unit in January 2011. We had to keep a towel on the floor to absorb the moisture. Our troubles began after the freezer door was left ajar and the interior became quite frosty. We had turned off the freezer several times to defrost but nothing helped until this morning when I read the comments of Marea of McClellanville, SC and Ruth of Vavenby, BC.I then decided to begin exploring taking apart everything until I reached the freezer unit in the back of the freezer. I discovered a lot of ice with the ice blocking the drain hole which is supposed to drain condensation from the freezer fins to a drain pan in back of the freezer. Apparently, leaving the freezer door ajar caused the drain hole and surrounding area to ice up. Condensation from the fins would keep dripping until it overflowed onto the bottom of the freezer until it filled up with ice. The water then had nowhere to go but out of the freezer onto the floor. The simple solution to this problem is to turn off the fridge, empty out the freezer and allow the frozen drain hole to thaw out. You can easily remove the back panel of the refrigerator to see if water is then draining into the drain pain. Good Luck! Ed

My glass stove top broke for the second time. The first time Whirlpool accused me of dropping something on it and chipping it. I didnt but paid the $400 glass replacement. Today while cooking, I put cold from the fridge not freezer, sausage into a warming fry pan. I heard the same pop I heard 2 years previously...sure enough the glass stove top broke. After a phone call to whirlpool, and hearing they were sorry but theres nothing they can do, I will write as many letters I can so others dont buy whirlpool.

Purchased a Whirlpool washer 14 months ago... however just unboxed the washer. Installed it in our new home. Now after just two, repeat, two months of use, there is water all over the hardwood floors... The front door seal is gone to the tune of $100 but what about my floors!!!!!! Im so discouraged after reading all the complaints that Im falling out of my chair. Seal design has been the same on most all their front loaders. DO NOT BUY A FRONT LOADING WHIRLPOOL WASHING MACHINE. YOU WILL BE SORRY YOU DID. Yes they look pretty. My parents old top loader washer lasted over 35 years without a repair and we washed clothes for four people.

2 years of use the wash plate went. $150 later, one year later wash plate went again (the wash plate is all plastic, the motor spline in metal total stripes the plastic teeth in the wash plate) I replace myself. 3 weeks later the shift actuator failed which cost another $60 which I replaced. Now the bearing is going. There are only 3 people living in the house. I would stay away from the top loader washers from Whirlpool h2 low series. Huge disappointment.

I bought a new non-frost 14 cubic Whirlpool fridge Model # W4TXNWFWQ in 2013 from PC Richards. The freezer keeps getting busted. It actually produces a lot of frost which stops the entire fridge from running properly. The tech said this is a common problem with Whirlpool. I am lucky to have bought the 3 years warranty. But when I call to fix the problem it always takes them a few days and I have to miss work for this non-sense.

Bought a Whirlpool fridge at Lowes sale when the previous Samsung suddenly died before the Thanksgiving Day. Under the circumstances at the time, it was largely a price driven decision (for a fridge of a certain size with some non-negotiable characteristics, though.) I could not be happier with its performance in the two years since the purchase.

We purchased a top loading Whirlpool Cabrio washing machine, Model #WTW8040DWO from Lowe’s on October 15, 2015. Since that time, we have had a service call on three separate occasions. The last service call, the service technician got Whirlpool on the phone with their technician. The washing machine would get stuck at 40 minutes and would continue to fill with water, drain and fill with water and would never progress.After the service technician talked with Whirlpool technician, it was explained the machines electronics were so sensitive that the washing machine had to be on an independent CIRCUIT (meaning absolutely nothing else can be plugged into the circuit). We contacted Whirlpool indicating that was not acceptable. Very few, if any houses, have a washing machine on an independent CIRCUIT. Whirlpools response - I have an independent circuit for every appliance in the house. Obviously, she does not know what a circuit is. Totally disgusted. Will NEVER buy another whirlpool product again. Horrible product and horrible customer service.

Whirlpool model N40T91 with FLAME LOCK - first failure was the controller valve only within 9 months of a new installation, replaced sort of free of charge, landlord had to pay ship charges. Days and days without hot water. About 6 months later, pilot failed to stay lit. Landlords maintenance man called Whirlpools Customer Service. They had him jump through hoops and finally told him to press a white reset button on the igniter. Okay, that worked. A few days later, pilot went out again, white button was reset, working again. Recently, and more frequent now, white igniter button keeps popping out, and we keep resetting it and relighting the heater, repeatedly, 4 times in one day.Maintenance man comes and calls Whirlpool Customer Service. They advise him to check this and check that. Everything seems to be in order. They say they will send out a qualified service person to diagnose a potential problem, a charge of $200.00. Maintenance man and landlord say, No thanks. Maintenance man goes to Lowes to buy a different brand model. Guess what? Envirotemp Hot Water Heaters have the same control device as the failing Whirlpool. He reboxed it and took it back and said, No thanks. Ill try to upload the images of the water heaters and controller you should stay away from purchasing. Meanwhile, maintenance man went to Menards and purchased a Richmond model, a well known, and reliable water heater manufacturer.