We had purchased matching Whirlpool Cabrio HE washer and gas dryer. Both appliances were worthless. Same problems as everyone else. Clothes did not come clean. Had to put it on bulky items just to clean the clothes due to lack of water. Funny how all the older machines that actually put water into the machine cleaned clothes. Went through a motherboard (computer) for both the washer and dryer at $250 each. Washer had repairman out at least 12 times over 3 years. Never again would I purchase a Whirlpool. We went to our local appliance dealer and purchased a Speed Queen. These are like the older ones. THEY WORK! They use the correct amount of water and wash your clothes in half the time. 22 minutes per load! You can open the lid while the water is running in and load your clothes. Gee, what a concept. Only company still making them in Wisconsin, United States. Go Wisconsin! They back their product with a 20 year warranty. What?? Who does that anymore? Companies who stand behind their product. We love our new Speed Queen.

Whirlpool side by side refrigerator/freezer Model #GSF26C5EXB. LESS than five years old and the ice maker is not working! Bought at Lowes. Great service. Out of warranty now. Lowes sent a repairman and it has to be replaced. I called Whirlpool and they said sorry. THATS IT? Ice makers dont ever last five years now? Unreal!

I am somewhat satisfied with my induction range. We ordered it just before Thanksgiving from Lowe’s a year and a half ago. We were told that we would have it before Christmas, which was fine with me. I don’t cook for Thanksgiving. Just a lot of Christmas baking. It turned out that Whirlpool had not started making our range until January and it wasn’t delivered until mid-January. It had been really good until about a month ago, when it blew the circuit breaker. My husband was cooking dinner while I was at work and it just blew the circuit breaker. No power surge in the rest of the house. No other circuit breakers affected. When the power was turned back on, two burners were out. As it turns out, the main circuit board is dead. So now the one large burner, a small burner and the ovens don’t work. There are two circuit boards for each oven. When it is working, it is a great stove. However when it doesn’t work, it is costly and takes a while to get repaired.

I have had too many problems with the thermocouple beginning about two years after I purchased the water heater in 2003. Whirlpool keeps replacing the thermocouple, but I have to pay for the plumber to come out and repair the unit. This runs me about $180 each time. The thermocouple has burned out three times since September of this year. The plumber didnt charge me anything the second time it went out. But it went out for the 3rd time today and he recommended that I replace the unit. Of course, it is out of warranty and Whirlpool was happy to tell me that I could purchase a new thermocouple at my own expense from them. I have paid for this water heater three times over with repairs. Whirlpool knows that there is a defect with the design of the water heater. There is no way that a regular consumer can get inside the water heater to clean it. I will never purchase any Whirlpool products ever! I advise anyone reading this to follow suit.

On 12/31/2009, I purchased a Whirlpool Cabrio, model# WTW6800WW1. I was excited as we have never spent that kind of money on a washer. We felt as though we had purchased a higher end washer and would have it for years to come. Wrong! About one year in to its use, I began to think it was getting louder during the spin cycles. I thought I was just being critical and it was just my sensitive ears. Now just past the two-year mark, I know it was not me. It’s the POS washer. It is so incredibly loud, not that you cannot be in the same room as it is during the washing time especially the spin cycle. In its defense, my clothes got cleaned.However, I know that the bearing is eventually going to give out and I will have a mandatory repair on my hands or have to pay someone to fix it. Either way, it’s a lot of time and a lot of money to fix a two-year old washer that should not need to be fixed. I attempted at getting Whirlpool to stand behind their product. No chance, no way. Good luck with that. Their washers last about 2-3 years. I will never purchase another Whirlpool product. This is a horrible product which is matched by their horrible customer service.

Whirlpool - Back in the 1980s we had Whirlpool appliances that lasted for many, many years. We are now in our mid 60s and retired. We purchased a new home 2-1/2 years ago. Whirlpool appliances were provided with our new home. We were quite pleased at the time. However, we are now sorry we have them.We are very easy on everything we own. When we replace appliances, cars, furniture, etc. we are generally able to sell our used items, which are always in great condition. Unfortunately, this is not the case with our current appliances. I will list the many problems.Combo range hood/microwave oven: it vented absolutely nothing. The microwave oven had its own set of just plain silly issues with the manner in which the touchpad had to be set. The oven did at least work. 2/2013 we had a Broan range hood installed and vented to the outside and purchased a Whirlpool countertop microwave oven. Again we had the little issues with using the touchpad plus the door was very hard to open. This countertop microwave oven failed 1/2015, less than a year of usage. At this time we purchased a Panasonic microwave that is much simpler to use.The Smooth-top range/oven looks nice. It is the most inconsistent range/oven we have ever owned. You cannot lower the cooktop burners to simmer. There is no simmer. On that setting it may as well be turned off. I can set it at about 9 oclock on the dial and some days that may be simmer. Others days it could be higher. Overall, the burners have no consistency. The oven cools quickly and I must be mindful not to toss in a 2nd sheet of cookies without checking the temperature. I have never had to do this on any other oven we have owned.The dishwasher does clean my dishes, thank goodness. However, I have had 2 service calls (under warranty) for a little gasket (hinge pad) which keeps the door propped a bit while loading the silverware into the basket. This piece has failed a third time I will just live without being able to prop the door. And then there is the silverware basket. Each piece must be loaded, handle first, into the slots on the basket. Of course, some of my silverware has wider handles so this does not work well. Such a poor design.The refrigerator was my pride and joy. We paid the extra charge for the French door style instead of the side-by-side style that came with the house. My charges here are more serious. 2 of the little door shelves have broken. Oddly enough these are small shelves which have some items on them that are not used often. If I choose to replace them, it will cost me over 25.00 for each of these little gems. Now, a piece of plastic on the veggie drawer has broken so I must be mindful not to let the drawer drop.Worst of all was the last service call out of warranty. I had standing water/ice on the floor of the freezer. Apparently this was due to a poor design and my service man replaced it with a new P-Trap that actually works. Yes, the original design was bad, yet I still had to pay for the replacement. Seems like this should have been a recall and replaced free of charge. Instead my total charge was 144.06. UGH!!! Now, I do understand I was likely provided bottom of the line appliances with my new home, but to have issues with all of them is ridiculous.

Just bought Whirlpool refrigerator, stove, and dishwasher. So far, the icemaker doesnt work and so I have no water or ice in the fridge. After four visits from Lowes it is still not resolved. Going on since 11/16/18. After waiting three weeks, the dishwasher came, and lo and behold - it doesnt work. Now I have to wait for one to be ordered! TAKE A WORD OF ADVICE - WHIRLPOOL ISNT WHAT IT USED TO BE. DONT BUY IT!

My Whirpool refrigerator model # WRF990SLAM01 was 14 months old (2 months past the new product warranty) when we started having issues with multiple areas. The ice machine stopped making ice and started dripping from the dispenser and the freezer stopped freezing food. I called and was told to purchase an extended warranty which cost me $375.00. The service tech has been to my house 12 times over the last 9 months. They have replaced multiple parts and even started replacing parts a second time. I was instructed by the service tech to call and request a replacement fridge. Whirlpool customer service told me that it would have to be considered a lemon before they replaced the product. I was told that would require each component to be replaced 3 times. I would need to take off work 27 more times for the repairs!!! The service tech came out one more time and he said there was nothing else he could do. I called again to complain and even wrote to Whirlpool corporation (though they never called me back at my request). After much complaining, which I do not normally do, they have decided to replace the unit. BUT I have to pay and additional $476.29 for them to replace this unit!!! I feel like I was totally raked over the coals from this company. I will never buy another Whirlpool product again and I recommend you do not either.

This will be the last Whirlpool appliance I will buy. We purchased this Whirlpool refrigerator Model # ED5GVEXVD literally a few days over 2 years ago. It is a side-by-side refrigerator with shelves that are supposed to slide out, however, we have never used it in that capacity. The problem is that the plastic frames on every shelf, even the ones that do not slide out over the bins, have cracked in no less than 2 places on each shelf.We contacted Whirlpool over a month ago. The good news is that they responded quickly. The bad news is that they stated, It is unfortunate that you had problems with the shelves, but we are unable to do anything for you because it is out of warranty. If you would like to purchase replacement shelves, we could order them through their consumer parts department. This is such a crock. If it was one shelf, I could justify the possibility of it getting smacked or something overweight was placed on it, but every shelf? As I said, not a single shelf is crack free, including the ones that sit directly over the bins, which should have additional support from the bin construction.By the time I replace every shelf that is cracked, it will be equal to what I paid for this refrigerator 2 years ago, and it will net me maybe 2 more years of service. If I have to invest that kind of expense into it, the refrigerator will go to the recyclers and I will buy from another manufacturer, which will definitely not be a Whirlpool or Whirlpool subsidiary.The cracks were noticed early last month. The cracks are already getting larger. I will no longer allow my children to get anything out of the refrigerator since Im afraid that the shelf will crack, the glass in the shelf frame will break and we will have an injured child, which instead of reaching this website, I will be contacting a lawyer. I need to do something with this refrigerator, but with the economy, I cant afford to just keep replacing a $1,000 refrigerator every 2 years.This refrigerator does not get extreme use since it is the 2nd refrigerator in the house. The primary fridge has been in our house since 2005 and I wouldnt trade it for anything. This Whirlpool refrigerator, however, is poorly made. The materials that the refrigerator shelves are made from were just a poor engineering decision because it is not holding up to mild to moderate use without cracking.We purchased this Whirlpool appliance thinking we were getting a quality product from previous reviews we had read, however, this is obviously no longer the case with this company and seeing the complaints that I now see online. Someone would have to give me really compelling evidence to make me decide to ever purchase another Whirlpool appliance again.

Same problem a lot of people have written about in your forum. Purchased a double door stainless steel refrigerator, bottom freezer, # GX2SHBXVY from Sears Canada on 12/17/2011. Warranty expired December 2012. Now we have ice forming on the floor under the bottom freezer though water hasnt seeped out as we are now cleaning it daily. Sears wants to charge $75 per hour + parts as there is no extended warranty. Whirlpool says its a common problem with most other Competitor models too. REALLY, ITS NOT. Have checked with a lot of friends of mine with similar models. Nobody is having a problem with especially units hardly one and a half years old. My bro-in-law also bought a Whirlpool a year prior to mine. He is having no problems. See no reason to spend $300-$400 on a comparatively new unit. Also have a 7-month-old stainless steel Whirlpool dishwasher and 4-year-old Gold Accura cooking range. Now spend morning and nights looking at them wondering when they are gonna blow. Need to replace my washer/dryer too but guess which brand I am not opting for.

This is the worst washer Ive ever owned. It consistently gets off balance, doesnt clean the clothes, and is a perfect example of poor design. I have owned the washer for approximately 9 months, and hate it. Im getting rid of it as soon as possible.

We purchased this Kitchen Aid stove December 7, 2016. I dont use the oven much, but have found that when it gets a little dirty and I use the Aqua Life function, it does not clean. Have tried by setting a pan of water in the bottom and raising the temperature to 300 degrees, but nothing cleans. We went with this feature to be more environmentally responsible. Leons, where we purchased the stove, claims that they have heard nothing of this issue and have not been informed of this by their head office.

I have a double door refrigerator with a bottom freezer. It is slightly over 2 years old and has been in use for only 7 months of that time. We just got off the phone with Whirlpool service. They will cover the cost of the control panel and defrost control. The other one I paid to replace was only one month old and it failed again. In the time between that I had to have an Icing kit put in as the Ice maker was causing ice to form inside the back wall of the refrigerator. My first call to Whirlpool was very unsatisfactory. I ended up paying for the part and the service call. The second call was about the ice-maker and they were aware of the problem and sent me a repair kit for the problem. I still had to pay for repair service. So far I have paid $561.62 for their defective parts and service calls. This time my wife called (while I was taking my frozen foods to my neighbors freezer for the second time) and went through 3 people before being told the part was still under warranty and they will send a new one. When we pushed for proper service we got it. We should never have had to go through all this. We also lost over $300.00 of frozen foods. Never buy a Whirlpool refrigerator!!!

Front load washer Whirlpool Model# WFW9400SW02, only had this machine for about five years and the main interface control board has gone bad. This part cost 1/2 as much as buying a new machine. My parents had the same washing machine for almost 30 years and no problems. Whats wrong with this picture?

I bought a Whirlpool wdf760sadmo. It was Oct 2014. It broke 31 days later. Lowes said they would not take it back. Called Whirlpool, they sent a repairman out a week later. They ordered parts and came back two weeks later. The parts were not the correct ones. Ordered more parts. This time back in a week. Ok about three weeks have gone by with a broken dishwasher sitting at my house. Got it fixed. A month later a different problem. Call Whirlpool, wait, on hold for about 20 or 30 minutes. They sent a repairman out who ordered more parts which will be in in two weeks. Meanwhile I am without a dishwasher again. I have had to take a day off work each time they have came to repair it. I have spent way too much time on this thing. I wont be buying another Whirlpool.

I have had my Whirlpool stove for over 30 years and use it daily. Still a great stove. I would not trade this stove or any of the new types. I just need to get the self cleaner repaired. The only problem I have is finding parts to fit this older stove.

We purchased the Top Loader Cabrio in 2006 for $1100. About 1 yr. later it just stopped, but was covered under a recall. A year later it stopped working again and cost $400 plus we bought a 3 yr. service contract for $350. A few months after the service contract ended, the spin cycle got very loud and it started leaking grease and water. It now need a ball bearing and $600 of work. So now we spent almost $2000 for this washer in 8 yrs. Our Maytag was $400 and lasted 15 yrs and we gave it to someone else who is still using it and we never had it repaired. It sounds like Cabrio customers have been complaining about the same issues for several years but they keep recurring and Whirlpool is doing nothing to correct them. We are not putting more money into it after reading all the complaints. We are buying another washer and another reliable brand. I would have been a customer for life because I did like the way it worked and cleaned, although I hear so many people had problems with that so I am not waiting for that to fail too. And I recommended the Cabrio to several people who bought them and now I hear they are starting to have problems. You should stand behind your product and correct these problems and recall or fix them at a reasonable cost.

This machine is 18 months old. First it failed to drain (LD code). Ran diagnostics and found the drain pump ($60) failed. The Mexican part was replaced with an Italian part. Two weeks later, the infamous F1 code flashed - control board. I sourced a new one. I ran one load and another F1 code is flashing. These are $150 electronic parts. Fuhgetaboutit. Im sending this ** to the dump and going back to electromechanical controls. I had a Maytag that lasted 15 years.

Bought this Whirlpool washer (WTW5000DW0) to save energy and water consumption. It has been awful from day 1. Clothes come out with detergent (white marks) all over them. Clothes aren’t spun out enough to dry them. It takes FOREVER for a load to finish, I can’t imagine that this is saving me anything on electric. Waste of money. Do not buy this!

On 02/25/13 we purchased a Whirlpool Gold Series side by side (French door) refrigerator with an ice maker at the cost of $1,850.00. In April of 2014 the ice maker stopped working and the freezer at the bottom would not freeze food. Luckily for us it was still under warranty and was repaired. At the time of the repair, the repairman (associated with HHGregg) told us that the refrigerator should have been replaced since the cost of the repair was more than the fridge itself. Now July 20th, 2015, the same issue has surfaced. Again the ice maker will not work and the freezer wont freeze. I would not recommend this product or if you do pay the extended warranty.

My $800 Whirlpool Duet Sport Electric Dryer quit working less than 4 years from purchase and needs a new electronic control board. My service tech called Whirlpool to confirm that this is the problem because replacing the thermal fuse did not solve the fact that my dryer wasnt working: Code F01. Diagnosing and repairing the dryer will cost me $375! I am deeply disappointed. I will definitely explore other brands before ever trusting a Whirlpool appliance because I know the company could have done more such as offering to cover or discount the $210 control board, because everyone I have talked with (friends, family, my appliance service company manager, Whirlpool customer service rep) agreed that this is a rare problem and that your dryers are engineered to work 10-12 years. However, as a company, Whirlpool gets an ** for customer service.

I purchased a Whirlpool microwave model #WHM3205XVS1 on October 2, 2011. The handle broke off in little pieces and was repaired in March 2012. Handle broke off again in little pieces in September 2012. This will be the 3rd handle that will continue to break in little pieces every 6 months. According to both repair men that were here, this is their comment: No customer abuse, this is a very common problem with this model. After to speaking to 3 people at Whirlpool, I was told by everyone, This is cosmetic problem and we will not fix after the 1 year manufacturers warranty is up. I started with the the first person, went to her supervisor, then went to her supervisor. I am now waiting for a call from a manager although I was told I will continue to get the same answer no matter how far up the chain of command I go. So, I was told that it is okay to have 2 screws sticking out holding the remaining part of the handle that is left, because it is a cosmetic, not a functional problem. I will never stop with Whirlpool. I will call 4 times a day if necessary. I will never purchase another Whirlpool product again! I will tell everyone I know not to purchase one of their products. Be careful. They manufacture products for many other companies, i.e., Sears, Amana, Jenn-Air, and many, many more.

My side-by-side refrigerator leaks water. I find water on the floor but we cant find the source. When I called Whirlpool, they stated its not under warranty, but we can schedule a repair appointment, I declined. Im still looking for the leak. Its intermittent, sometimes I dont see water for a while. The last fridge we had, we had to get rid of it because the sides and front got too hot to the touch. I was afraid it would cause a fire.

I have had no issues with this brand of microwave. I have had built in microwaves before with this same brand and they have performed well. We use the microwave every day for some reason to heat up food or make hot drinks. I feel Whirlpool is a good product and value.

I purchased a Model WRF989SDAB01 Whirlpool refrigerator with the French doors and had it delivered in March 2014. The evaporator developed a refrigerant leak in May 2015. Whirlpool said it was not their problem since it was over a year since I bought it. The technician said this is a problem with this model. I am having it repaired under the extended warranty that I bought. One of my concerns is that the unit has two evaporators so the other one will probably start leaking any time. What a piece of junk. Dont buy Whirlpool. Their quality and service stinks!

Bought a new set of Whirlpool Cabrio Platinum tin replace my Maytag that had finally died. I believe this is the worst set Ive ever owned. It wasnt inexpensive but its cheaply built. Cant wash a set of sheets without it getting out of balance, even if you carefully place them in the washer as they recommend. They knock up no matter what you do. The dryer is gas and my clothes still have to be turned back on for more time that should take. We are talking about over an hour. Ive had them just a few months but Ive had it. I want my washer and dryer to just do their jobs like you expect. Im selling them or donating them but whichever they are out of here. Whirlpool, I am ashamed of you. Putting out such a poorly made washer and dryer. Instead of the name Platinum. They should be named Salvage. Never again Whirlpool. Never Again!!!

I bought a Whirlpool water heater in 2009. I paid $588.46 at Lowes. Turns out it is in a class action lawsuit for faulty thermocouple. I was given a coupon from Whirlpool for 2 new thermocouples as part of the class action lawsuit. The thermocouple goes out on it every 1-3 months. You never know when youre going to have a cold shower getting ready for work in the morning. I literally could have bought a new water heater for what Ive spent on thermocouples the last few years. The last two times it went out, I had to replace it twice within 1 day. Im sick of replacing it and have decided to install a new hot water heater. I am disgusted with Whirlpool and tried to contact them about it but have gotten no response. I will never buy another Whirlpool product and would not recommend them to anyone!

We bought this washer brand new and as soon as it was outside the one year warranty the bearing went out. They had to order a whole new drum kit. A MONTH later I had a running washing machine again. The day after it was fixed it started leaking underneath the machine. Serviceman came and looked at it and said No must be the hoses (my responsibility to fix). Nope kept leaking and two months later Im doing laundry and an entire load of water floods my laundry room. Drum broke again!! SIX WEEKS LATER I still am waiting for a new drum. I had to fight to get Whirlpool to fix it again and they wont even return my calls about why its taking so long! We are a family of 8, so doing laundry at a laundromat is outrageous! Dont ever buy Whirlpool washers!!!

We purchased the gas slide in range with gas oven. Immediately the temperature would hold a consistent heat, therefore it continually reset with a start sound (swoosh) every 5 minutes. The manual says it will do this, but clearly this is not normal. Then, the oven stopped working, showing an error message FBE0, that the cooling fan is not at high enough speeds! It sounds as though, along with hundreds of other people, we have all been ripped off! If anyone can please tell me what can be done about these defective stoves, I would appreciate it, thanks very much!

We purchased commercial washing machines for our building, we discovered that the clothes were coming out of the machines with dry spots and partials of soap. When we asked the dealer about this they sent a tech. to check the machines. It seems that these machines do not allow a adequate amount of water into the tub to wash the clothes. Only 6 or 7 inches of water is not enough water to wash a full load. When asked how this can be fixed I was told it cant be fixed. I was told this is a energy saving machine, which means you can only wash very small loads!What is the point of running a machine for twice the amount of time to do what you used to do in one load? Had we known this before purchasing what we felt was a quality machine, we are now stuck with machine not capable of doing what is required of them. When asked if they would take the machine back, no is all they say. I would never buy any product made by Whirlpool or Maytag because of the way this problem of ours has been handled. We purchased these machines from Prestige appliance, they have been good, but with no support from Whirlpool.

I purchased a Whirlpool Cabrio on October 27th, 2010. The Cabrio is always giving me the UL code, which indicates the load isnt in balance. Ive been doing laundry for 27 years. I know how to load dirty clothes into a washing machine evenly. Sometimes it will take me all day to do one load of laundry! Seven months after my purchase, my Whirlpool Cabrio washing machine started giving me the F51 error code. I called the phone number on my Lowes receipt for warranty work. Two weeks later, I finally had my washing machine running again. I was happy and thought Id only have to deal with the UL code. Boy was I wrong?!Now Im two weeks away from my warranty expiring. Im getting the F51 error code again! This washing machine is an $800 piece of junk! Hopefully, I can get the Cabrio repaired before my warranty expires in two weeks. I do a lot of laundry. We are a family of six. So, I know Im hard on washing machines but come on. Shouldnt an $800 washing machine last at least two years? Im not even a full year into owning this junky washer and Ive had two breakdowns! In my opinion, this washing machine needs to be recalled and people need a reliable replacement or refund.

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

This dishwasher does not clean the dishes. Having said that most of the dishes are too oversized for the small capacity. Perhaps the fact that this is such an old dishwasher. I’m not sure but none of the dishes get washed. About the only thing that works is the dryer heater. Sorry to say, I’m not happy with this dishwasher and wouldn’t recommend it to anyone.

Yes, Whirlpool makes Maytag, Im still paying for this junk. Too much to go into detail. I had to bypass the crummy fuse system in the Bravo dryer and hook up my own 15amp automotive fuse in the dryer to keep it working. This after two lame under-contract Maytag repairmen replaced the dreaded board, which did nothing. The washer goes cabunk, cabunk, cabunk throughout the house and shuts down with an unlevel code (no matter how level the load is) every time it does its load during the spin cycle. The dishwasher handle broke off and had to use a screwdriver to pry the handle latch open, until realized it doesnt even lock anyway and just pulled the door open. Now, the dishwasher has this noise problem which means they designed it to allow pieces of debris to escape past the trap like my other dishwasher had that was easy to remove and clean. Do not, I repeat, do not pay the $3,500+ I paid for this junk. Go buy a Kenmore thats 15 years old off of Craigslist! Youll be better off and it will last longer.

I bought this dishwasher in Nov. 2018 to replace one that was barely working. I have enjoyed using it much more than my old one. Its very quiet and does a great job of cleaning dishes, pans and silverware. The only problem we had was installing it. The leveling screws do not hold their height adjustment when the dishwasher is pushed across the floor during installation because the leveling screw pad was changed from steel to plastic and the tapped hole for the leveling screw is too loose. The effect of this - whereas the steel pad would slide the plastic pad will grab, turn and move the leveling screw out of adjustment. Especially if its tapped hole is too loose. So we went to Home Depot and bought 4 5/16 nuts and used them as lock nuts on the 4 leveling screws. This cost 50 cents. Once we installed it everything worked perfectly. It does take longer to complete a cycle than my old one - 3 hours vs. 2 but it uses less water and does a great job of cleaning. You must use a drying agent with your dish soap or it wont get dry enough. Also, if you use the short 1 hour wash it wont have as much time to dry and some dishes wont be completely dry. I usually wait to do a full wash with the normal cycle - 3 hour.

I have had our new Whirlpool Cabrio Washer for about a year. I absolutely hate it. I along with all the other people that is complaining about their Cabrio. I have found it to stain my clothes, not get them clean... Sometimes not even get part of them wet. I wash every load now no matter how small on the deep water option. I still have to add about 3 to 6 gals of water after it fills to try to help them get as clean as I possible can. I have stopped using fabric softener because I believe that is what may be leaving the stains on the clothes because it doesnt dilute it. Also you cant soak clothes in the washer long enough. I know it offers a presoak but when the clothes are not getting wet... That is not soaking. I tried to fill it up and raise the lid so it wouldnt wash until I was ready for it to wash but it automatically emptied the tub after a short time.It is funny watching the clothes when washing... Even I could tell they were not going to be washed well. I thought who in the world developed this washer. Certainly no one that had ever really considered what women need to wash clothes on a daily basis. I would sell it but I dont think anyone would buy it. If there is a class action suit I would consider joining in. Whirlpool could not have spent much effort in checking this washer out. A lot of money down the drain. I did not buy the dryer because of the lint vent being on top of it. What a mess those make when you have to empty it. So I purchased a Maytag Bravos XL. Now that is a wonderful dryer! As one homemaker to another I suggest you check it out. Never had one I liked more.

I purchased a brand new Whirlpool washing machine only 2 yrs ago. Rather than lasting upward of 10 yrs with normal use as advertised, the machine is nothing more than a giant wash tub. It doesnt Drain and Spin properly. The clothes are still wet at the end of the cycle and I have to either attempt to wring all items by hand or set the machine to Drain and Spin for a second time. Now, it no longer agitates the clothes during either the wash or the rinse. I am SO disappointed in this and very angry that I trusted this well known brand with my hard-earned money. I am also angry at myself for not reviewing internet posts as I am hearing the exact same experiences by others time and again.

Over-the-range microwave hood combo - It is not that it does not work, it just wont shut off! Close the door, it turns on. Touch the side, it turns on. I have walked in the kitchen and found it on! I am afraid it will turn on when I am not home and burn down my house! After reading the poor customer service received by others, I will just replace it.

The stove is only 5 years old. The oven would not ignite. The gas was getting through, but theres no flame. Sears repaired it and put a complete flame and ignitor piece at a cost for a part of $132.00. I feel the stove is too new to have to replace anything. I am retired, so I do not use the oven often. I have only cleaned the oven one time in five years. It is very clean. I picked this stove out and paid $900.00, because I liked the style and everything about it. I feel you should look into this, and I should not have to pay for repairs in such a short time of ownership. The repair person said this stove already had an upgrade in it. Please respond. Does the whole heating element need replacing or just the ignitor?

We purchased Whirlpool dishwasher Model #GU3200XTXB Nov. 2011. Two weeks later they replaced the soap/rinse aid dispenser because the rinse aid was running out the bottom of the dispenser. Feb. 2012 they replaced the handle which was loose. July 2012 the panel lights werent working and that was replaced. Feb. 2014 the soap dispenser door would not open, so the dispenser was replaced again. March 2014 the soap door would not open again so the computer board was replaced & the door did open. However, it stopped again 3 days later. April 2014 the dispenser and the board were both replaced. The rinse aid dispenser did not dispense leaving the inside with moisture on everything. So yesterday the dispenser was again replaced but now the rinse aid is running out the bottom of the dispenser. Thank goodness we purchased an extended warranty for $169 or we would have spent more than $1,000 on repairs!! The warranty company refuses to acknowledge that their lemon law should apply. There are 2 of us and we use it 2/3 times weekly.

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

Our new home came with brand new appliances. I love our Whirlpool microwave. Its reliable, quick & has lots of great pre-programmed features to assist with regular. The independent timer is a total bonus too.

Our refrigerator is only 18 months old, a Whirlpool Gold gx5htxvyo5. It was sold to us believing it was stainless steel. There is no way scratches come from nowhere. We have a Whirlpool dishwasher and stove in stainless steel. You cant compare how much better they are. Im very dissatisfied. Wed like to have new doors. Something is very wrong with the finish on these doors.

I bought one of the top of the line Maytag washers and was very disappointed. It only lasted about 5 years and had to be replaced. The dryer I bought at the same time is still working. It is 15 years old.

Stove was purchased in June, 2021. Two months later, oven will not heat up!!! Contacts Whirlpool, and TEN days later, a service person finally shows up. Problem appears to be a circuit board that they dont have, and has to be ordered! When will it arrive? He has no idea!!! I called Whirlpool, but its frustrating and a waste of time. You only get to talk to someone that appears to be reading from a script! If were lucky, well be without an oven for one month; however, it could be two...or three...or four!!! My advice: Dont buy this stove/range!!! Not only is the oven an issue, but it just seems flimsy and subpar quality, especially the oven door. Added to that, the glass top is very difficult to keep clean... Worse than any glass top stove weve had in the past.

I bought a Whirlpool/Fridge Freezer Model WRF560SMYM 01, less that two years ago. Two months ago it started making a terrible noise. Apparently the freezer was iced up and a mechanic defrosted it. It happened twice more and he left saying he could not fix it. Another arrived and took the model number and he disappeared. A third the same. Now I have an empty freezer, just an ice maker. It seems to not freeze up so quickly with the moisture control on. Over $2,000 down the drain unless somebody can fix it. Oh and the fridge gets very cold! Does anyone have any ideas apart from throwing it out and buying another? Never another Whirlpool!

Bought a Whirlpool dishwasher about 2 years ago. Used it once a day for one year. The bushings already need replacing (maybe $3 to make) and it’s $270 for the part or $280 for whole motor. Do the math. Not impressed.

This refrigerator is a disaster. You will never be able to leave your home for any length of time for fear of a storm putting your electricity out which turns it off and if it DOES NOT TURN BACK ON WHEN THE POWER IS RESTORED. If you happen to be away for several days you will come back to a freezer that has defrosted all over your floor and your food in the refrigerator spoiled.

The oven steam cleans the oven but it only cleans the bottom, not the sides, back or door. They dont recommend oven cleaner so how do you clean it? My oven is a year old and looks like its never been cleaned. You would be better off with non cleaning oven and using oven cleaner. It would be less work. Horrible stove.

Whirlpool water heaters are a disgrace!!!! I have never been so dissatisfied in my life with a product. I bought this water heater 11/2017. Three months later, it was not working. Whirlpool sent an igniter and I had a technician to put it on. This was a short fix because it broke down 2 weeks later. I called customer service and of course they gave me the runaround. I will never ever buy another Whirlpool product. This company is the worst.

We bought our Terrorpool Whirlpool refrigerator in 2006. We have had problems with the ice dispenser, bad motor replacement, and now we have cracks all down the right inside wall. I had bought an extended warranty of four years at the time of purchase which covered the cost of the previous problems. But it has now expired, and I was told it would be my expense for repair. What happened to reliable appliances that our parents and grandparents had? What happened to the name Whirlpool? I will never buy a Whirlpool product again, not to mention the customer service (which I wont mention). If you have model # ED5PHEXRQ00, please write about any problems you have had and help someone else not make the same mistake.

We bought our Whirlpool Cabrio washing machine and dryer in May and it was the worst purchase we have ever made. We have had a technician out to our home three times. Whirlpool said that the next time the technician comes out to your house, you will have to pay for it and we have the extended warranty! The problems with the washing machine are many. 1. Leaves white streaks on dark clothes. 2. Not enough water covers the clothes, so clothes do not get clean. 3. The spin cycle is so violent that clothes are damaged. 4. The soak cycle is a joke. Soaking means to sit in water and soak. This machine drains the water so there is no soaking.5. With this very expensive machine, we can use only one cycle; bulky items on the low spin with a repeat rinse.The dryer is equally terrible. As I write this, I have two pairs of jeans going through the dryer for the third time. According to the technician, a heat sensor determines whether the clothes are dry. We have not had one load of laundry, big or small, that has dried in one cycle. But the technician said that this is how this machine works. We have tried all the cycles. According to Customer Service, the technicians found nothing wrong with the machines hence, we will have to pay for the next repair call. If you are looking at this machine and dryer, dont! Do not waste your money or your time. Washing laundry is a nightmare because the machines do not do what they are supposed to do --wash and dry the clothes.

My Whirlpool has all basic features and works for household jobs. It is extremely useful for routines like towels and clothing. It also works gently enough to launder curtains and goose downquilts. Operations are very simple and the controls make it very simple.

Whirlpool washing machine has always been reliable for me. I have owned 2 and they lasted me many many years. Its easy to use, and cleans clothes perfectly. My family is also a fan of Whirlpool appliances.

We purchased a Whirlpool washer/dryer set 19 months ago and the washer just stopped working. Our trusted fix-it man came out and diagnosed it as a spin bearing problem assuring me it was not anything we had done. He stated it was a defected part or Whirlpool had never put grease in the bearings. A 450.00 part not counting diagnosis and labor. When I called Whirlpool, the first response I got was that they were sorry but we didnt buy the extended warranty, and of course the warranty it had was only a year. I asked to talked to a supervisor and finally she agreed to supply the part, but I was still responsible for the diagnostic and labor fee, which will be a couple of hundreds of dollars! Not happy with Whirlpool and will NEVER buy any product with their name again. Beware consumers!!!

Originally, I loved my machine. At the one year mark, my washing machine began a f51 error code. I looked it up and it had a recall. The entire board had to be replaced. Now, I keep getting a ul code and it will not quit. Also, the inside of the top is rusting out so badly that chunks of rust fall into the washing machine and stain my clothes. I wish Whirlpool would fix these common errors. I see many other people complaining online that the same thing is happening over and over.

I bought at Lowes. The first one was sent back (doors stuck, suction cracked lining). Now the temps are not working in the fridge or freezer. All the food got dumped. Its sad. My old one lasted closer to 25 yrs. (and may I add up to ten children). This one has only been used by adults. I thought I could trust Whirlpool?! I sent info to local Lowes. We will see if theres any help.

The control panel is difficult to use. It’s much too easy to switch power from the top oven to the bottom oven without knowing it. In addition, the plastic cover over the control panel makes it difficult to use especially if your fingers have flour or oil on them. It would be much easier and more accurate if knobs were used to control the all the functions instead of a electronic screen. Also, the clock has never operated accurately. Always runs fast. Temperature of the ovens is pretty accurate. However, it does take a long time to reach chosen temperature. Both ovens are large and able to handle an 18 inch round pizza dish. Other than the control panel, I’m pleased with both the gas stove top and both electric ovens.

The Whirlpool microwave has been very reliable and efficient. I like its multiple functions, from heating up leftovers to defrosting meat and poultry, baking potatoes. All the functions are easy to use.

I purchased the 19 cu. ft. Whirlpool Estar refrigerator WRT 3595FYW on 4/28/12. Freezer began showing frost immediately. Repairman from Marcellas Appliance where purchased - (518) 381-1957, came to check it, put a sealer around the door openings of refrigerator and freezer. Frost continued. I called Whirlpool. They sent another repairman from EB Russell in Schenectady, NY, door needs replacing. Door was ordered and when received by them, the door was replaced on my refrigerator.In August 2012, frost is in freezer, on its roof, on the door daily. I called Whirlpool. I told them I wanted to remove it from my home. Whirlpools reply was, you have a repair warranty, not a replacement warranty. I was not advised of this when I purchased. Otherwise, I would have gone to Sears, Lowes, etc. On 8/16/12, another repairman from The Appliance Man, Albany will be here Monday. Its dishonest sale, replacement was advised possible by Marcella, that it was just a matter of course to get an okay from Whirlpool. This is not so. There is no replacement or return policy. Please help. Thank you.

Within 5 years, this is my experience: A broken brand new Whirlpool fridge after 6 months of purchase; a broken oven that needed repair after 1 year, and today, the oven door just shattered in pieces after I heard a loud noise from the kitchen, almost injured the kids. And guess what, I just returned a new Tilt-Head Stand Mixer KitchenAid that wouldnt stay in place; the head keeps on tilting and would not stay locked. After being on hold on the phone for almost 3 weeks for a return, I found out it was a Whirlpool brand family. This is horrible, I would suggest to never buy the Whirlpool brand; their products are a real nightmare and their customer service is not reliable. If you do buy from them, expect unreliable products and very long long wait periods on the phone.

It goes off balance, frequently. It is moldy and stinky. I wipe it out, use a cleaner and leave the door open, but it still stinks. I am getting rid of it and buying a Speed Queen top loader. I am extremely disappointed in the front loader Whirlpool.

After only 6 months of use, the cooktop light bulb burned out. When I tried to replace it, the glass part of the bulb separated from the base. The bulb is screwed in so that the base faces away from the front of the microwave. With the small cavity and the backward installation, it will be impossible to remove. Now I have no light and dread how much a service call will be. The unit was installed by a contractor prior to our purchase of the house and it is now out of warranty.

I have a whirlpool water heater. This is the third or 4th time that the upper sensor failure code has come on. Our water heater turns off all the time and we have to fire it back up. In the past few months, it has started pouring water out from the long tube on the side of it anytime we turn it on for more then 10 minutes. The last time we called a plumber, I was trying to get a quote on a tankless water heater. Ive been so fed up with ours and I thought that would be a better route to go. The plumber explained the negative sides to a tankless water heater and explained that our water heater was a really nice, really expensive and fairly newer model. I told him that I had just gotten it about four years ago. He said he could just fix that one. So after looking at it, he acted as if he didnt know what an upper sensor was and told me it was under warranty and that I should call for the parts. Every time we have called for the parts, they send the same box thing on the front of the heater and every time, it doesnt fix it for long before it says the same thing. And now, like I said, the water heater has now added the problem of pouring water out of it. I need help. I dont know what to do. Im tired of not knowing if Ill have hot water or if the water heater is going to pour out water. Im pregnant and worried that if we cant get this fixed Ill continue to have this problem along with having a baby to take care of. Please help.

I purchased a Whirlpool Gold side-by-side Refrigerator on June 15, 2013. The freezer works fine but the refrigerator does not feel that cold and when I put a thermometer in there, it reads 42-43 deg although the refrigerator is set at 37 deg. The tech was just here and told me to put a thermometer in a glass of water and read it again. His thermometer read 46 deg when reading a bottle in the door although he explained that he had had the door opened for a while during his visit. He said his reading of the bottle upon opening the door was 36 deg. I do not believe that. I just measured some bottled water temperature and it was 48 deg. I have a hard time believing the temp went up 12 degrees and he has been gone for a half hour. My food is cold but not like you expect from a refrigerator. My bottled water and soda, etc., are not very cold. The worst is the water dispenser. That water is barely cooler than tap water. There is almost no difference. The water temperature has been in the 60s when Ive measured it. The tech says the first glass wont be cold (have never had that with any other refrigerator) but even if you get the second and third glasses of water, they arent any colder... maybe a couple of degrees. If anyone else is having this problem and Whirlpool will do nothing, then Im interested in legal action.

Pros: The refrigerator is large and roomy, easily adjustable glass shelving, and easy temperature controls for the refrigerator temperature and freezer temperature. Cons: the refrigerator is bulky and limits space in a small kitchen. The lower freezer door does not seal very well and requires frequent tweaking and adjusting around the door seal. Also, the freezer handle becomes loose easily and requires tightening fairly often -- which is a pain to get on the floor on your back (and a flashlight plus a special wrench) to tighten the handle.

Purchased over range microwave WMH31017AW-2 from Best Buy Mar. 12, 2015 and after installing it noticed code Door appeared and that there also was a dent on side. They replaced on Mar. 19 and we had the same Door code problem. Called Whirlpool and they sent out a Tucson repair tech and he ended up coming out at least six times changing 3 switches, 2 cams, 2 brackets, control board, and line filter. Still had problems and Whirlpool requested he call their tech and he did and they told him to make the same changes and he told them he already did all that and there still was a problem. Then Whirlpool told him to switch some wires on control board which did not solve anything. Then second thing they told him was to file and clean door brackets which also did not solve the problem. We called back to Whirlpool to tell them we did not want this defective microwave any longer as all these repair trips were not solving anything. They wouldnt give us a answer right then and said they would call us back 24 to 48 hrs and we are still waiting. We will never recommend Whirlpool to anyone nor ever buy from them again.

I purchased a condo last year with all appliances included. My Whirlpool refrigerator model is GI6SDRXXY00, a fairly new refrigerator. I noticed orange and moldy spots on ices when dispensing them. I changed the filter, thought maybe it is the filter causing the issue. But after inserting the new filter and emptying the entire ice tray, I still get bad ice! I open the compartment, and surprisingly, found out that the spiral rod inside the ice dispenser was rusted! This is horrible and unacceptable! This is not a user fault but a manufacturing defect. The parts that are in direct contact with what customer consumes should be robust and safe. I contacted customer service, and they gave me a technician phone number which turned out to be a third party which only cares about money. They said they will inspect the refrigerator and will charge me $134.00. I will not use this refrigerator anymore and will replace it soon. AND I will never purchase any more Whirlpool products. This manufacturer is crossed out from my list of vendors who I do business with.

I bought Whirlpool front load washer at Sears in June 27, 2012... (serial W104408696A) (W10409178A-SP). I had 6 episodes within a 1-year time that my clothes got burn holes and the inside of the washer. I would find a handful of gray powder after doing my laundry. The first time it happened, I thought that I left something inside my clothes that resulted to it, but I did nothing to contribute to the event. The second time it happened, I thought Im putting the wrong setting, so I chose another setting to wash my clothes. In that span of 1 year it was on and off happening. I read different reviews on this washer, and I am not the only one whos had this problem. Finally in 2013, before my warranty would expire, I requested for Whirlpool to fix the problem. Right away the tech told me that the problem was the glass covering, so they replaced it. Now my washer would not drain. I believe that this product does not belong in the market. If they knew what the problem was, they should have recalled it. I kept the sample of that gray powder.

Bought a Whirlpool hot water heater from Lowes 1/08/12. In May of 2013, it would not work. I had to replace the Gas Control for around $100.00. It was 4 months off warranty! The same thing happens 3/2014. They sent me a new Gas Control Valve free and shipped it overnight. This is no fun to fix. I cannot believe that I need to flush the tank out with cider vinegar every 6 months. That is why I was told it keeps breaking.

I recently had the bake sensor go bad on my Control Panel of our Whirlpool Gold AccuBake Oven with microwave. Not a problem correct? WRONG! While the Whirlpool people were very professional in helping me (a shout out to them), the part I received was the wrong color. It was white; they called it a biscuit color. My oven is black. I have no idea what Whirlpool actually calls that color. Anyway, in my visit with them, I was informed the black control panel has been discontinued. Am I the only person that has a black control panel? This $280.00 part is now going to cost approximately $3,000.00 to replace the entire unit. Is there anyone that can direct me to where I can find a black replacement control panel? Way to take care of your customers Whirlpool. Solve this and I will give you a great shout out.

I purchased a Whirlpool fridge (model GX2SHBXVQOO) on November 27, 2010 and it leaks water on my floor. I have to keep a towel there or it runs all over. I also purchased a Whirlpool range (model YGFE461LVQ) and the convection fan went on it a month after we bought it. The manufactures warranty does not allow repair people to travel any further than 100 km to repair, something that we had to take the stove in to be repaired. We got the stove back the same day and brought it home. Low and behold, after a short period of time it started to rattle again and got steadily worse. Also, now my one burner on high does not stay on high; it keeps going out then coming back on.I have called the place we purchased these pieces of junk from and they said there is nothing they can do. I also sent e-mails to Whirlpool and they said they will look into it and get back to me. That was months ago. I called Whirlpool and was basically told that there was nothing they can do, that I was to call the repairman. Never, never, ever buy a Whirlpool product.

I had a full set of kitchen appliances delivered to me on December 11. The delivery crew installed everything but the microwave because we needed to have wiring done. Three days later an electrician came and upon opening the microwave box it was severely damaged. Whirlpool won’t replace it because I called one day outside their 48 hour window. They delivered me a damaged product – period. It should be replaced without question. Instead they want to send a “cosmetic tech” out to see if it can be fixed. I can’t imagine that’s a more cost-effective method for them. Completely unacceptable. I will never buy Whirlpool again based on their lack of customer service and common sense.

Whirlpool is a very good company and their products work very efficiently! If I had a choice to choose in a different type of washing machine I don’t think I could choose. Whirlpool is very reliable. Their older machines as well as their newer machines! They last pretty long. The dryer is dry very well as well as the washing machines agitate your clothes to get them clean.

I purchased my Cabrio a little over three years ago. Within the first month, the computer board had to be replaced and the tech informed me that it was not a malfunction in the unit; rather, it was because I did not have a sock bag for my socks and panties. I replaced the board, bought a sock bag and had no problems for about 1.5 years. A little over a year ago, the un-level started. I did research and found that I needed to replace the rods and add couplers as they were not thought of when the unit was created. This worked for an entire month. Now, I am in the same position again. It takes about 6 tries per load and the amount of water I am using is increasing with each failed attempt to wash. There should be a recall on this product. I notice there are many other complaints that match my frustrations exactly.

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

I bake a lot so my husband bought me a new gas range for our 54th anniversary. After the first few times I used the oven, I decided to clean it. I noticed then that there were some burnt grease spots and streaks between the oven glass door. After 2 years of use, it has gotten much worse so I decided to take the door apart to try to clean the glass in between the layers of glass but there are three instead of two. I cleaned the inside of the outer glass, but that didnt take care of the problem. Most of the stains are between the other two panes of glass. That, I cant get to. I feel that this is poor design and not sealed properly. I take good care of everything I own and I expected this range to last me the rest of my life but it is put together with cheap plastic parts that wont last long. It is the first new range that I ever owned and paid a lot more for it than any Ive had. I expected better.

I purchased a Whirlpool classic range model number rf263LXTS0 on January 2010. We had some hang-ups on the kitchen renovation and were not able to install the appliances until May of 2011.I used the cooktop that evening and was very pleased. I then went to use the oven 2 weeks later and it did not heat up. I asked the contractor to check things out (maybe it was something minor that he could fix). He checked the things that he installed and everything on his end was working fine, so he told me to call Whirlpool.A service technician came out and, within 10 minutes, said that the oven controls were defective.I paid $450.00 for the oven originally. The service technician charged me $136.74 for 10 minutes to tell me that the oven control needed to be replaced (that is the major part of the oven) and that it would cost me $318.41 to replace the part.I called Whirlpool and explained my circumstance and Paula, the supervisor from Tennessee, said that there was nothing she could do. I told her that even if I installed the oven back in January of 2010, the major part of the oven should last more than 1 and 1/2 years.What terrible craftsmanship and crappy customer service. It is sad that customer service cant stand by their product and Whirlpool has to rely on making their money on repairing defectives products. I now have to go out and buy a new oven. I also buy a lot of appliances in my business and I will never buy a Whirlpool again.

Do not buy anything Whirlpool makes. I purchased a new home and new appliances. In less than 4 years motor is gone in dishwasher. 6 weeks later I have another leak that has ruined my hardwood floors. My fridge is making all sorts of weird noises and alarm is going off. They are coming to ‘look’ tomorrow. And my washing machine is no longer draining. Whichever you buy from check how the extended warranty works... Trail Appliances Calgary uses a company that is horrific to work with, doesnt have a human to talk to and wont acknowledge you unless you pay $149 upfront. RUN AWAY!!!

Mtf18 defective refrigerator - The unit is 2 yrs old and about 6 months prior to 2014 I could not keep ice in the refrigerators ice (freezer) and the appliance compressor ran 24 hrs. a day without recycling or stop. I did not purchase an extended warranty, after all, Maytag the dependable company. The lonely Maytag repairman. Right!! The unit cost $$700. and is now an anchor. You cannot repair the compressor, only replace it...

Does not get your clothes clean. They come out of washer smelling due to lack of water. Darks have Detergent Residue on them. My t-shirts have holes in them. Bought this machine in 2010. Just purchased a Whirlpool top load with a Agitator and I am very pleased with the results. We never had any problems with Whirlpool products but this Cabrio should be taken off the market, faulty advertising. Talked to a Whirlpool rep and she told me to bunch up clothes and place around outside edges of machine for best results but did not see any difference. Do not buy this washer. You will be wasting your money and you will be buying a old traditional washer, with an Agitator is your best bet so you can control the amount of water you use. I hope this helps one that is thinking of buying the new technology top load Cabrio with HE.

After 2 years the motherboard failed on my Top load Cabrio washer. We had to spend $300.00 dollars to get fixed. When we called Whirlpool to see what they would do about it, they actually offered to sell us the board for $345.00 dollars and a 1 year warranty on the board. They actually wanted us to pay more from them than a local repair service. DO NOT BUY THIS MACHINE OR ANY OTHER WHIRLPOOL PRODUCTS. Also does anyone know of any class action lawsuits surrounding their obvious use of defective parts?

This is a good customer service (CS) review. Whirlpool knows about the defect and continues to distribute the fridge this way. We have a Whirlpool model #WRF757SDEM01 we purchased this year (2017). We love the size and the fact that the ice bin is in the door and takes up very little room. Our only complaint prior to this issue was the ice and water do not always come out gracefully. So we were happy overall till a large block of ice formed in the back of the fridge. My original call to CS was great. They did not ask me a bunch of stupid questions, just said that should not be happening and scheduled a service call.Service guy knew exactly what it was because he had repaired the same model with the same issue several times. It is a defect in the dual cooling/defrost system that Whirlpool knows about, but continues to produce. Two parts need to be replaced and one part had to be ordered. Which was not a big deal since two days were needed to thaw out the mini glacier. We lost food so I made a second call to CS and again there were no stupid questions or arguments. They got a $75 debit card in the mail to us. So I thank Whirlpools CS reps, but sure wish the manufacturing side of things were a little more diligent in production. Certainly this cost them money on all accounts.

Bought side by side in 2010 and after the first 3 mth the ice maker jammed up. Found out the dispenser door was not working right so it was change. But lo and behold the dame thing jammed up again within 3 weeks and the door is working. I will never buy WHIRLPOOL AGAIN. I hope they go out of Business. They are selling junk and they do not care. Made in American. Pack your bags Whirlpool. You are no longer needed.

I purchased this Deep Cabrio Washer and Dryer a year ago. We moved into our new house and put in the new washer and dryer. During the first load in the washer, the spin cycle blew the ring right off of the hose and flooded our new laundry room and bedroom in the basement. My husband had to put a clamp on it to secure it. The washer does not wash the clothes, in fact you have to always wash it under Deep Water and wash it twice using twice as much detergent as you normally would. This washer is horrendous. My best friend bought the same one at the same time and she hates it just as much as I do as it does not clean clothes. Whoever designed this washer should be fired from Whirlpool. Im hoping through Nebraska Furniture Mart and Whirlpool I can find a solution.

We bought the Whirlpool refrigerator from Home Depot. The ice maker does not work. We get 2 cups of ice a day. Home Depot Told us we should get 8 to 10 pounds of ice a day. We call a repair service and they said we should get 2 pounds of ice a day. Still getting 2 cups a day. Call again and now they said we should get 64 cube of ice a day. So now Home Depot has us calling Whirlpool instead of them. Now we will have another repair company coming out. Waiting to see what they have to say.Very disappointed with Whirlpool for not backing their refrigerator. And don’t buy from Home Depot. You can’t return if you buy it. And I have a warranty on it and they have a lemon law 3 repair calls for the same thing and they will take it back. Not true. I will be calling once a week for 5 years until they get me some ice. They don’t deserve a 1 star.

The washer constantly binds clothes around agitator. Truly a design flaw and it does not get clothes clean. So with a washer like this, I am forced to go to laundromat. Wished I would have paid 230.00 or so to have transmission fixed on old Kenmore. Truly dislike this substandard appliance.

Very pleased with my Whirlpool dishwasher. It is not the top of the line but does a great job of cleaning my dishes and is very quiet when running. Whirlpool appliances have been very good to me.

I bought it a year ago and the warranty is not even up and only in about a month the freezer door handle keeps falling off then the stainless steel which probably is fake is rusting too. They replace the handle and the door and the handle still keeps falling off and the doors are rusting again. My GE stainless steel dishwasher and stove are five years old and there is no rust on them. Whirlpool says it is cosmetic and that its not covered under the year warranty. I will never buy Whirlpool again. Awful customer service!

I bought my fridge 6 years ago. 13 months after purchase I had to replace the compressor. Last month I had to replace the water drip pan. Now the fridge is knocking and hissing again and warm inside. Compressor needs to be replaced. I contacted Whirlpool and they said 6 years is old for an appliance. Seriously!?? What about 13 months when the compressor went? They obviously dont stand behind their products. They are unable to admit I got a dud. Im so disappointed and frustrated. Stay clear!!!

My microwave is very reliable and has lasted a very long time. I have never had a problem other than the circular glass plate that broke. It took me a little time to get use to the timer on it which is a little different than other microwaves that I have used. Overall a good buy.

We went out and bought the new front loader washing machine and dryer. Neither one of them works correctly. A service call had to be made the the day we ran the first load. The washing machine only washes errors popping up F8 and E3. On the dryer error code E3 pops up and cannot dry clothes. Worst purchase I have ever made.

Our new refrigerator was delivered on March 28, 2015. On May 31 as I was opening the door, the top of the bottom door handle broke. I was finally able to get a door handle shipped to my home and I replaced the handle. On July 21, I am opening the door and the 2nd handle breaks in exactly the same place again. Two broken handles in less than four months. Terrible design flaw in this door handle. Now, I am being told by a service representative that the handles are only warrantied for 30 days because handles are cosmetic.

The Whirlpool Cabrio washing machine it’s the best washing machine I’ve owned. Water temperatures are right on, has an express wash 38 mins for lightly soiled clothes, plus the normal, delicate, heavy, bulky, 2nd rinse, if you need it. My wife loves it because it’s very Gentle on her personal items. Energy saver AND BEST OF ALL, IT REALLY CLEANS THE CLOTHES.

IM OLD AND DISABLED WOMAN. Bought a brand new $800 Whirlpool top loader washer and it wont work after not even a month. Called whirlpool and had the worst customer service from Tammy. I have to wait to compose myself to call back cause the washer is junk... F9E1 SENSOR. IM NOT A MAN! Worst customer service. Thought my washer would last longer. Its been 1 hour 45 minutes. Wont turn off. I CANT unplug TAMMY! IF I COULD I WOULD!

Whirlpool accubake slide in gas range - After using the auto clean button on the range, the digital panel will not work and the oven door will not open.

I purchased this machine in April and already, the right leg is rusted and the under seam of machine is rusted. I have throw rug under it and where the leg is, there is rust on the rug. I called service from Whirlpool and 2 servicemen came out. The first one told me I was loading it wrong and the water was splashing over the inside tub to rust the leg and I asked, So why is the seam under the machine rusted? No answer. The second one came out and told me he could not find anything wrong with the machine and doesnt know why it is rusting, but he never gave me a paper to sign off on. He also said that maybe it was rusted when it was delivered. Not!!! Then I call P.C. Richard in Watchung, NJ where I bought the machine at and told them about the problem. They sent a serviceman out and he said that the bleach condensation is causing the rust, its known fact that this machine has this problem. He said that the water does not run through the dispenser but there is a model that does. I want a credit on this machine and get the upgraded one. It states on the machine that I can use bleach but it doesnt say it will cause rusting. I want you to tell me how a 9-month-old machine is rusted on one leg and the seam underneath is also rusted!!!! I had a machine for 10 years and it wasnt rusted. I am very unhappy with this product and with the customer service of Whirlpool. This is my first Whirlpool washer and I would not recommend this washer to anyone. I paid $600.00 for this washer and it should not be rusting.

WRF989SDAM00 - We spent about $1800 on a Whirlpool French Door refrigerator and at 1.5 years we had to replace the compressor for $700+. Apparently Whirlpool will only warranty for 1 year. The repairman told me the compressor he was putting in is exactly the same model as the bad one he took out so I guess I am not surprised that it only has a 1.5 year working range. We are now 1.5 years into the new compressor and sure enough it is dying again. Now it sounds like a jet plane taking off. By the time I replace it again I could have bought a new refrigerator. I am trying to figure out if this refrigerator is on recall because I cant keep replacing the compressor every 1.5 year. Never again will I purchase a Whirlpool product. I think they know the lifespan of that compressor and that is why the warranty falls just short of it!!

We bought a Whirlpool cook stove with a black top in 2009 and this year, in 2011, while cooking a pot of stew, the stove top burner began to make loud popping sounds. When I went to check it out, there was smoke coming out from under the pan and pieces of glass that had exploded out in small chunks. When calling the customer service line at Whirlpool, they told us that it was no longer under warranty and could not be of help. Their only explanation was that they would only cover a new stove top if it had cracked or broken this way when putting a cold pot on a hot burner. They said their technician could tell if this was why the shards of glass were exploded from the burner.

Very concerned. First the microwave broke. It seems that is burning on the inside. The model number is MH1150XMS-2, purchased in 2005. I have had to replace the plate. I have read of many recalls, because of the potential of fire. My model was not among the ones on the recall list.