I had my old agitating washer for 8 yrs that went out. I liked Whirlpool so decide to try their washer. Found the Cabrio washer (SWS5000WO) and thought without the agitator it would give me more room for clothes to wash better. Boy was I wrong, no matter what cycle or what size load it is off balance on the very first spin. I have to stay near by to stop the washer before the first spin adjust the load and start over again. Jeans and towels are impossible to clean. It throws the tub so bad it has pushed the side out. I have checked the balancing rods and they are fine. After reading other complaints realize the Cabrio washers are terrible. I will be looking for a refurbished washer with an agitator and doubt I will buy Whirlpool again. They should have a recall on these machines. They are terrible.

I purchase a Cabrio WTW7800XW0 3/28/11. After the year warranty I started to notice sand like substance in the drum of the washer, which lead me to look around the drum. I noticed that the light was completely rusted and flaking, the area around the light was rusted as well. I call customer service at which time they said it was not warrantied, but they sent me out a new light. This did not repair the problem! The rust has continued causing the area around the lid joint to break. Also the area around the bleach dispenser is showing rust- the same side as the light and the lid break. They have said this is not covered and only agreed to pay 1/2 of cost of materials (no service).

I have the Cabrio washer that is only four years old. It is leaking oil and is very loud during the spin cycle. I paid $800 for this washer and am extremely frustrated that it didnt last longer than this. I contacted Whirlpool customer service and had no luck since it is out of warranty. Due to the high number of complaints with the same issue, please consider a class action lawsuit. Thank you.

Whirlpool realized in 2002 that this was a defective part. In 2005, they recalled the product. I purchased the Hot Water Heater (Model # BFG1F4034T3NOV) in 2006. Being this product was recalled in 2005, why was it still being sold at Lowes and other stores? Why wasnt it pulled from the shelves? Why werent the parts replaced before being sold? The hot water heater stopped producing hot water. I contacted Whirlpool and they said the gas control valve had to be replaced; they gave me a part # and an authorization # and told me I could pick it up at Lowes. I asked about installation, because it is still under warranty. They said they dont service this. I picked up the part and tried to find a plumber to do the work and they said it was too small a job. I had to impose on friends to help me; one is a volunteer fireman. He came out and put on the new part and in doing so, another piece broke. We called Whirlpool and they said they had to replace the manifold door assembly. They overnighted the part. Again, I asked about them servicing this hot water heater and I told them I am a single parent and cant do this work. They said they dont service this item. I then had a handyman come out to try to fix it and he wasnt able to get it to work and now I smelled gas (it cost me $198). I had to call the gas company and they came and said there was a leak and turned it off and gave me a violation. I called the company I have an HVAC contract with and they added the hot water heater to that contract and it cost me $120 more for a year. They finally got it working, I was without hot water for a week. I do not recommend anyone buy products from this company. They are horrible to do business with and their service is awful (the service they dont offer).

We purchased a new Whirlpool water heater April 2013 at Lowes and every 3-4 months the pilot would go out. My husband would simply re-light the heater, I guess he didnt think it was a big deal. However, in September 2014 the water heaters pilot went out and would not re-light, so I contacted Whirlpool about the warranty. It took 4 telephone calls (two of which involved a plumber, per Whirlpools request), and several days of cold showers for an authorization code to purchase a $8 part (thermo coupler). The hassles that Whirlpool put me through, no one should have to endure. Who ever heard of a technician telling you that they have to talk to the plumber, when you call them to explain a problem with your water heater, such as, the pilot will not stay lit and the plumber said it is the coupler (I couldnt remember the whole name of the part, but surely they should have understood what was wrong). Secondly, providing a plumber (unless youre married to one) to converse with them involves more money. Now I have a plumber at my house so I call Whirlpool and this technician insists that the plumber perform a test on thermo coupler to make sure that it was faulty before she gave the authorization for a new one. Yet again, when I called to Whirlpool with the plumber, while I was voicing my problems in resolving the issue of my water heater with this technician, and she just hung-up on me. So as not to be defeated and having already invested in the expense of the plumber, I called Whirlpool again and requested a manager. The technician asked if she could help and I informed her of my previous encounters. She apologized and took my information to have a manager to call me later; however, she did give me the authorization code for the thermo coupler without delay. When I went to purchase the part, I didnt have the old part (as trade; the plumber hadnt removed it), so I paid for it out-of pocket, to return the old part later.

Purchased a Whirlpool refrigerator the last week of January 2014 with promised delivery date of February 6, 2015. Received call Feb. 2 that the earliest they could deliver would be February 13th. Received call Feb. 3 that the earliest they could deliver would be February 19, almost 2 months after purchase of refrigerator. Sears, where we purchased the refrigerator, told me that they have been dealing with this for 10 years with Whirlpool. Why would Sears sell products to their customers with this kind of delivery problem? They only communicate with Whirlpool via email, so there is no resolution with a person to get issue taken care of. We will never buy a Whirlpool product again & will never buy anything from Sears again.

Purchased the Sears Oasis (made by Whirlpool) washer and dryer almost 4 years ago and I have worked on these machines more than the Maytag machine and dryer I used for over 22 years. Electronic and mechanical problems. One recurring problem is loose change working its way into the drain pump on the washer and it knocks a hole in the side of the housing. You later discover it when you go down to the basement and find about 50 gallons on water on the floor. Very poor design! Never happened the first time with the Maytag.

On 9/28/16 I purchased 4 new Whirlpool appliances from Orvilles Appliances in Buffalo NY. They were delivered on 11/9/16, the refrigerator was installed. The microwave, dishwasher, and range were not installed until Jan. as my kitchen was being remodeled. Both doors were dented; it took 3 months for Whirlpool to send new doors. After installation water began pouring all over, gallons of it; it took a month to get fixed. The microwave door has a large defect and the surface light does not work; it is still not fixed. Six months later it is still it fixed. I feel like I paid a lot of money for defective appliances. Whirlpool is truly a company that does not stand behind their products; they could care less about their customers. I will never ever do business with Whirlpool again. And Orvilles also refused to help; it was a mistake to shop there.

If I could give Whirlpool products and their customer service zero stars, I would! We built our beautiful home that was complete in June 2015. Our builder was installing Whirlpool products in the homes he was building at the time. So we decided to accept the microwave, dishwasher and drop in gas range that he offered. We had never had Whirlpool kitchen appliances and no reason to respectfully decline the brand. We bought a french door Whirlpool refrigerator as well so the handles would match our open concept kitchen.In addition to the poor quality overall, the microwave makes a terrible buzzing noise that has been fixed two times thus far. The refrigerator is so loud at times that its difficult to hear the television when sitting in the living room. The dishwasher does not dry the dishes on any setting to include heat dry hours and hours after the cycle is complete. This forces us to hand dry our dishes prior to putting them in the cupboard. The cast-iron grates on the drop in range already look terrible because the enamel is coming off. I clean all the appliances as recommended by Whirlpool and like to keep our home beautiful because it is our place of solace and comfort. As stated prior, our kitchen and living room are open concept so I now have to contend with an eyesore in the middle of our homes hub because Whirlpool considers this manufacturing flaw as cosmetic and wont cover it under warranty.To add insult to injury, these poor quality products are the higher end available from Whirlpool. We plan to wait for the year end warranty to expire and replace the four appliances with a brand that has always offered excellent customer service and has been very reliable and trustworthy for us. As a consumer, I would save yourselves the agony of purchasing any Whirlpool appliances!!!

Purchased this oven on 9/12 from Sears, did not purchase an extended warranty and didnt think it was necessary. Im a 64 year old widow and only use the oven on holidays, to date Ive used the over 5 times. With Easter coming, I decided to clean the oven. Followed the instructions, the door locked and the oven died. Im totally disappointed, now it would cost over 100.00 to repair, money I cannot afford. Called Sears and all I was told over and over again that they can send a repaid person and I would have to pay. I was also told that I should have purchased a Kenmore and I wouldnt have had a problem and finally I was told that they couldnt fix it and referred me to whirlpool customer service, who also told me it would cost over 100.00. A 19 month oven should not have died. It should have cleaned the oven and continue to work for many more years. Again, Im upset, angry and disappointed with sears & whirlpool. And dont know what to do. Does anyone else have this problem with the oven, is there a recall?

I bought a commercial coin operator washer (Whirlpool washer model CAE2743BQ) for $800 and after using it for 4 months the washer stop working. The main board panel lights turned all and the washer did not start. Called Whirlpool several times and nobody could help me and told me to look online for a distribution center to get parts. The customer service only knew about regular washers not coin operator. The washer had only 3 months warranty from Home Depot and I was supposed to pay for all the repairs and Whirlpool would pay for parts. So far I spend $400 in repairs and the certified technicians could not repair the washer. They replaced the actuator shift, the main board etc, etc and nothing. The technicians reset the washer at least 10 times, calling Whirlpool tech support and the washer worked for one load and the main board lights stayed on all over again, the start button did not work. I sent a letter to the warranty department that I got online and they told me to call the same 1800 that I had called at least 50 times in the past year. Now it has been more than one year and the machine is defective. Technician said could be the soap that my tenants are using, or overloading the washer or an electric problem that they cannot identify. I gave up... I will not buy a coin operator heavy duty washer from them again. I requested a return authorization for a defective product and I did not get anywhere. Thanks.

First, the storage drawer doesnt close properly aligned. When viewed from the side it looks off kilter. This is because the foot of the range interferes with it closing. Second, what is with the bright blue color of the time/temp on the computer screen? Everything else in the kitchen is green, but now I have bright blue(?).

This machine cannot handle washing jeans, towels, blankets, pillows or anything bulky or very small loads. The load becomes ul unbalanced almost every time I try to wash a load. It has never gotten things very clean.

My husband and I have been loyal Whirlpool consumers for over thirty years. When it came time to purchase a new refrigerator, we purchased the GC3SHAXVY00 model. It was quite expensive but we decided to splurge. This was the worst mistake. Let me also state that we have had the refrigerator now for maybe 5 years. Within the first 6 months, the door that is the central operating system for the appliance went out. The appliance was still under warranty at that time, so Whirlpool ordered a new door. The technician replaced the door and left. However, within 15 minutes of the new door being replaced, the entire refrigerator began to shut down, not just the freezer. Fortunately, we had the techs cell and we called him and he came back and put the old door on until he could order another new door. That made three doors in the first 6 months of us owning the appliance. Then, the ice maker started freezing up. We were told just to defrost the ice maker once a month, that this was a problem the company was experiencing with this 500-dollar refrigerator. Then, the water line started freezing so we would have to leave the freezer door open for about half an hour every week to get the line to thaw so that we could get the water to come out of the dispenser. Now, the ice maker has quit completely. Are we going to call a whirlpool tech? NO, what for?This refrigerator has been a true lemon from day one. I have three more Whirlpool appliances that have broken down within 6 weeks of purchasing them. It was time to replace our appliances so we thought we would support our local economy by purchasing Whirlpool. To say the least, that will never happen again. I will be replacing all my appliances with LG from this day forward.

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

Right from the start of buying a new suite of Whirlpool appliances, the light over the range burnt out. We figured it was just a bad bulb so we replaced it. Soon it burnt out again, replaced it again, then again it burnt out. I finally called Whirlpool about the problem and found out it is the electronic panel that needs to be replaced... Of course at a full charge to me! I am so over WhirlPoo, (yes I spelled it that way on purpose) every single appliance has had issues. I have just lived without a light over my range because fixing it is more expensive than buying a whole new microwave. Never again will I buy any WhirlPoo appliance!

I like the Whirlpool oven ranges because it is easy to operate, easy to clean and like the features and functions. I have had no issues with the stove and I have had it for four years already. So far still working good.

This is the information I tried to send to Whirlpool only to get a message that it was undeliverable: I purchased a set of whirlpool cabrio washer and dryer on 10-23-2013 (model numbers WTW8540BW, and WED8500BW). On 01-25-15 the washing machine failed to power up just over 2 months out of the standard warranty. This wasnt the low end cheap models. With cash discounts we paid over $1600.00 for the set. After a $70.00 dollar charge to the repairman we are told that the unit has a bad electric control board (part # W10761026). And unfortunately the part is on back order until March 1st, 2015 as of right now. So if and when the repairman gets the part and installs it, I get to pay him an additional $260.00. My family has always been such a dedicated Whirlpool appliance purchaser but this is wrong.Oh I almost forget, now I have to rent a washing machine at a cost of $55.00 per month until mine is repaired. I believed I was purchasing Whirlpool quality. The type of quality that doesnt need an extended warranty because Whirlpool is made to last correct? Please assist me in making this situation right and restore my faith in the quality I was raised with in Whirlpool products.

This microwave had been the best I have used for several reasons. One is the modern design that goes with our kitchen. Two: it heats the food very quietly and produced an even temperature through out the food. Three; The inside of the microwave is easy to clean out.

In May 2010, I purchased a Whirlpool WFW9750WW front load washing machine. In October 2010, the machine started making a strange noise and by December 2010, the machine sounded like a jet airplane. I called Whirlpool warranty and they sent out the appliance doctor. They looked at it and said that the bearings were shot and needed an inner basket, outer basket and one other item. They would order it and come back in a week or so. We were told not to use our machine. Ten days later, I called to check repair status and they said that the items were on back order until late January. I called Whirlpool and after several conversations and going to the second level of supervisor over a week time frame, they finally located the part and shipped it. However, it was not until the end of January 2011 (seven weeks after my call for service) that the part arrived and was installed. The sound was never right after the repair. The appliance doctor came out and told me that all washers are loud. In December 2011, the jet airplane sound returned. I called Whirlpool but I was now out of warranty. Luckily, I bought the extended warranty through Lowes. They sent out Night Owl on February 9th 2012. They diagnosed the same problem with the bearings and said they would order the parts. I called Night Owl on February 17th to check on status and they said that the parts were ordered. I called to check status again today and now the parts are on back order (same as last time) until sometime in March. Night Owl turned claim over to check on getting the machine replaced rather than repaired. I was told that this would be another five days. Its amazing how there are no parts available. I was told the repair cost for this item is over $450 as it takes two repairmen about two to three hours to complete. Issue is still not resolved. I highly recommend not buying a similar washing machine. Whirlpools product, warranty and customer service suck.

I purchased a Model WRF989SDAB01 Whirlpool refrigerator with the French doors and had it delivered in March 2014. The evaporator developed a refrigerant leak in May 2015. Whirlpool said it was not their problem since it was over a year since I bought it. The technician said this is a problem with this model. I am having it repaired under the extended warranty that I bought. One of my concerns is that the unit has two evaporators so the other one will probably start leaking any time. What a piece of junk. Dont buy Whirlpool. Their quality and service stinks!

I bought front-loader WFW8540FW1 in November 2017 from Lowes. I keep having problems with the washer not turning on. I am waiting for the repairman to come. Had repair done in March, May, and now June. I have gotten new electronics for replacement from Whirlpool each time. Obviously something is defective. Is there a lemon law for washers? Hope so. Never buy Whirlpool Washer again!

This machine is JUNK and in need of a recall!! DO NOT BUY!!! This was purchased at Lowes for nearly $800 a couple of years ago and what a waste of money. During the first year, they had to send out a tech that told me he was not familiar with top loaders and was not sure why the clothes were not getting clean, nor why they came out with a white residue on the dark clothes. We used the machine cleaner - which the cycles take nearly an hour (how is that efficient?), put in a load of dark clothes WITH NO SOAP and guess what? Then he had me dump in a gallon of vinegar to clean the tub and the wall of the washer and repeated the process and guess what? He informed me that it was just lint. Well, after several visits and using a suggested pin drop of soap, the problem remained. I finally asked him if he was so sure it was lint and not soap residue, would he be willing to taste the lint? It was soap.Obviously after an hour of washing in the efficient washer, the clothes are not getting rinsed. I know this because in just putting in less than ten dark t-shirts, they came out dry!!! He informed me that since he was a contractor for Whirlpool, he was not allowed to continue to come back as he resolved the problem that I was using too much soap! Well, that is only part of the problem. This piece of crap leaks. We not only have a water softener, but a household filter system. In just the last three months, we have replaced the hoses as they are corroding. We were informed by Lowes that the hoses that came with the washers were from China and that they have been replacing them with US made hoses to the customers at no charge due to the amount of returns. Well, those too have been corroding and now I once again have water on the floor.It cost $1.75 to take my clothes to the Laundromat, 26 minutes to wash and ten minutes to get there and back. That is what I have been doing, and using my 23 year old dryer when I get home. It is a shame that the company is not responding to an obvious problem. I only wash two loads in a week - not like I am beating the thing to death with numerous loads or heavy loads. I will not recommend, in fact, I BEG you not to spend your hard earned money on this junk. Buy a $200 washer and if it too craps out in three, four or five years... you are still ahead. You will even save money on headache medication and save your sanity.

I bought a Whirlpool dishwasher in 2008 from Best Buy and purchased the extended warranty through Best Buy. First of all, my complaint is not with Best Buy (model # DU1145XTPBA). I have had nothing but trouble with the unit not filling with water, being noisy, and other problems. And then, my intelligence is insulted by these independent contractors, who are supposed to be appliance repair specialists. I found that far from the truth in most cases. They have a list of patented things that the consumer is doing wrong: not having a hot water heater next to the unit, using too much detergent, not loading it properly, and on and on. They must think we are idiots. I always would run the water from the sink till it got hot before filling. And I am a miser so I use less detergent than what the manufacturer or the detergent package says. Anyway to make a long tale short, it started leaking last week, so I assumed the door seal or some other such thing. But lo and behold, the door is rotted out at the bottom. The black finish has bubbled up and the metal is actually rotting away. I am from up north and it looks like my old Chevy 2 Nova rotted out. I called Whirlpool and spoke with several people and supposedly someone in management. They were, of course, sympathetic but offered no assistance or explanation. They offered to send a factory authorized repairman to replace the door at more than the cost of a new dishwasher. Are we that stupid? They never offered me a voucher for a discount on a new unit, which I am going to have to buy. I would not have accepted it anyway, as my last few experiences with Whirlpool have been dreadful. I will never buy another Whirlpool anything. The name used to stand for a quality product that you could depend on. But now it is like most things are offered to the consumer in this throw away society. And as long as we keep buying inferior products and only expecting them to last a few years, I am afraid that is what we will continue to get. Be vocal and let them know how you feel, even though they are probably yawning on the other side of the phone. They are without compassion and could not care any less. They are just looking for a paycheck and have probably heard a hundred complaints like mine, so its water off the proverbial ducks back. But when its their own job in jeopardy, perhaps they will start passing on these complaints to someone who will be willing to listen. Its a very bad experience and I will never buy Whirlpool again.

What a horrible experience. I purchased a Whirlpool Duet HE Front Loading Steam Washer in 9/9. I have used it no more than 15 times. It has an error code F70. I called Whirlpool and used one of their recommended technicians. He was there for no more than five minutes and he informed me that it was one of the two parts--one is $300, the other is $500. Both these parts are computer chips. He instructed me to call Whirlpool stating that they would give me the parts for free. I did, and they refused stating that the product is now out of the one-year warranty. This is clearly defective. I am now faced with $1,000 fix. I feel that I was further misled by Whirlpool because they should have told me before the service call that I was going to have to pay $1,000. The customer service reps and the manager were both unresponsive and rude.

New stainless steel range 5.3 cu.ft. with convection oven delivered by Home Depot on time. Before the day was over the trim around oven glass was falling off. Double sided sticky tape was not holding. Yes its put on using double sided sticky tape. Called Home Depot, once you accept it, you deal with Whirlpool. They must first send someone to look and see. Yes its falling apart. Service tech will order new door. Mind you it will also have the sticky tape. We have also noticed that the glass top has many deep scratches, he will replace that also. A week later still no word, when. Used the oven because I couldnt wait and as it heated up smoke poured out of it and a loud noise from inside. Turned off and pulled out bottom drawer to unplug. Bottom panel had fallen down and undersides were rusted. Only had the stove 3 weeks and its Christmas Eve. Will read reviews first next time. No problems with my other Whirlpool appliances.

I like my dishwasher very much. Because we have hard well water I use Lemi Shine to cut down on any deposits. The top shelf is adjustable so that helps with large pans getting clean.

This washer (Cabrio 6th Sense Washer) is less than 4 years old and now needs $500.00 worth of repair. You have to replace the tub in order to replace the bearings. If your washer starts to make noises during the spin cycle, you are in for a big repair bill. I still havent decided if I am going to repair it or junk it. The towels always smell sour even if you wash them twice.

Purchased Whirlpool Washer Mod# WTW57ESV1 12/9/2011. Washers transmission blew on 1/20/2012. Requested Whirlpool replacement. No results. Will never purchase Whirlpool products again.

I recently purchased a Whirlpool Slide in Oven replacing my Amana stove of 15 years. My Amana was a very basic model, and I thought this WP was an upgrade. But it is so poorly made its ridiculous. First of all the bottom storage drawer, is so flimsy, it does not slide out easily, and the top lip doesnt even have a finished edge. Additionally there is a 1 inch gap between the top of the drawer and the bottom of the stove door. But the BIGGEST disappointment was the oven racks, totally flimsy.We used a Lodge Dutch Oven (which we have used many times with our old stove) and the oven rack sagged under the weight. Had I known I would have pulled the racks from my old stove. I contacted that seller about these issues, and they said they are ALL like that even the higher end ones, and I contacted Whirlpool to see if I could buy better quality racks and they said no, this is all they have.

Oftentimes when we take out the dark loads there is a white line left. It appears to be detergent that does not go into suspension. We are using HD. Just lately we switch to liquid. Question in our minds is if it does not move the water enough to put the detergent in suspension, how in the world is it even cleaning? I do not see the turnover of the clothes. Where is the quality control with this?

We bought this Whirlpool Cabrio Platinum washer 1/21/12. After less than 2 years of use, it now sounds like a jet plane taking off on the spin cycle. It is the first Whirlpool appliance I have ever bought and IT WILL MOST LIKELY be the last. After years of using and buying Kenmore appliances I fell for the salesman pitch that this was a better product. After spending $900 on this washer new, Im now told by 2 repair places that service your products that the repair cost for parts is$450 and then labor will total over $700. NOW to add insult to injury, this same machine now sells for $519 new.

I like the newer technology that is built into the washer. My only complaint is that the wash time is automatically set depending on your load choice. For instance, a delicate load is set to wash for 45 minutes. I dont feel that amount of time is required.

After 6 years, Our $2500 Whirlpool refrigerator stopped cooling and would not dispense ice. Since we had purchased a Whirlpool extended warranty, a Whirlpool authorized technician replaced the compressor and informed Whirlpool it also required a new door that included an ice dispenser. A door was not available so Whirlpool refused additional repair and refunded the $400 purchase price of the warranty. Meanwhile the refrigerator stopped cooling again and Whirlpool refused any additional obligation. The refrigerator was now non-functional and we had to spend $3500 to get a comparable refrigerator. The moral: 1) Whirlpool makes very expensive refrigerators that have about 30% of the life-span compared to earlier vintage refrigerators. 2) They know this and will promptly refuse to warrant their product if it is to their benefit. Shame on you Whirlpool for using your corporate leverage and shady business practices to manipulate your customers.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

Worst company for home appliance... I got my fridge repaired from an authorized service person and next day it again stopped functioning. Upon calling the service center again, they said that few more things needs to be repaired once again and for that fridge needs to be moved to their workshop and for that they will be charging 1600 Rs again. Upon asking for the refund for the useless spare part, the rude service person said ek din k liye to chale tha na fridge, fir kis baat ka refund... Such a ** company is Whirlpool that they are not entertaining any complaint on their all India customer care number...

I purchased Whirlpool Washer WTW4815EW on December 29, 2015 for my tenants apartment and by October 7, 2016 it was not working. I called Whirlpool for service since the product is under warranty. The closest appointment was more than 2 weeks out. On the appointment date the technician called me and said he was on his way to my house which is more than 30 miles from my tenants apartment. The technician said he could not service the tenant area as that was a different group, so we rescheduled for a week later. A week later no one shows up, so I rescheduled yet again for November 3rd and drove myself to wait for the service person who was supposed to be there between 8 am to 12 PM. At 11:40 I saw there was a 10:36 am Whirlpool attempt to call me but no message was left. When I called back they told me the technician called in sick and they called at 7:30 (my iPhone indicated 10:36 am). Now they say someone will come on Saturday November 5th. It will be one month on November 8th with no working washer. While it is bad enough the washer stopped working in less than one year their service support is even worse than the product.

I bought a Whirlpool gas stove (WFG745H0FS1) 2/1/18. The front control knobs (W11122880) position ink began rubbing off after a year. I sent them pics, their solution was to pay $45 each for new knobs.

We bought this at Lowes. Initially, they got the color wrong. It took two trips to get the right color (white) then a third trip because all the parts were not there to install the dishwasher. After a few months the second shelf rail end caps fell apart. Now, after a couple of years the pump goes out. RUN from this manufacturer.

Lu ** is a mgr. at Whirlpool customer service. Shame on you for the way you spoke to me. Then giving me a joke # to call... Karma sucks is all Ill say to you. I have to wait on the phone to speak to anyone is over 30 mins. Just to get pushed off to the side like I dont matter. Im trying to get help to have mine looked at to pass the time for another Whirlpool to come to me! Mind you mine didnt last 4 yrs. Yes I was trying to buy another Whirlpool but after this sloppy customer service. You dont need this stress... Stressful enough that these washers dont last anymore. Ya GE AND MAYTAG ARE LOOKING BETTER AND BETTER.

BFG2F4040T3NIV IS HORRIBLE. This water heater is JUNK. The release valve has released and flooded my basement 3 times in the past 2 years and the recovery time on water is terrible. Whirlpool needs to step up to the plate and refund everyone who purchased one of these. Every review on this unit is horrible. DO NOT PURCHASE a WHIRLPOOL water heater!

I have had the machine pair (Whirlpool Cabrio Platinum) for almost 4 years and up until a few months ago I LOVED the washer. I was advised when I bought the machine to make sure to read the manual, which was very helpful in learning to use it properly. I have never had residue on my dark clothing or ever had the clothes come out partially dry. I use liquid HE detergent nothing powder goes in the machine. I also read many reviews before buying it and a got some advice from them. I have washed king size comforters with no problems. Everything has always cleaned very well. The only issues I have are that when bleach was used in a previous cycle. Ive had a problem with the bleach not being fully dispensed and ending up in the next load. Fortunately it was just towels and not darks!!! Although, I had just bought the towels and now they look tie died which was very upsetting to me. I learned to add water to the bleach dispenser to dilute it and that issue seemed to dissipate. BUT NOW... I COULD THROW A TANTRUM. I PAID 1800+ FOR THE PAIR AND THE WASHER IS SHOT!!! A pretty common problem with the Cabrio from what Ive read. It started by making a very loud noise when spinning, like a helicopter was landing in my laundry room! I continued using it, I even thought the sound was getting better after I did the clean cycle. The last load I did would not complete the cycle because it kept reading that it was unbalanced and unfortunately it was a load of heavy wet towels. I was far from happy when I had to remove them and go to a Laundromat. Needless to say its the bearings and to fix its very costly. I cant even fathom that a less than 4 year old machine needs to be repaired and the cost is roughly half of what I paid for it!!! I do know I will NEVER buy another Whirlpool. What happened to making things to last??? Next machine I will definitely get extended warranty. I can honestly agree with all the other reviews... THIS MACHINE IS HORRIBLE!!!

Bought a propane hot water heater and 2 years after buying it pilot wouldnt light. Had to buy a conversion kit because they didnt make the part anymore. Now had to buy a gas valve and it didnt work so went to Lockes and bought a new water heater and now they wont refund my money for the part $300.00 with shipping. They said they could only replace it. Well I dont need it now because I bought a better product. Whirlpool is junk and you have to buy the parts from them and RIP you off. Way to take care of your customers Whirlpool. Buy something else with your money.

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

The refrigerator has worked OK except for occasional freezing towards the back. However the vegetable bins have both broken starting with various parts of the handles in front. We eventually replaced them. A brand new one arrive already broken. Same cheap brittle plastic. No alternative available. The company denies any problems or complaints about the bins. Feels like a small profit center for them.

I bought my fridge in late 2008 and I am already experiencing potentially expensive repairs due to what I believe is a defective design system, of which, consumers are having to bare the consequences for those who collected our hard-earned cash and delivered a lousy product! I saw so many similar complaints about the ice system on this fridge that I am almost positive that it qualifies for a class action suit and settlement. How about a collaborative approach to this since we have all suffered needlessly? Tell me what you think and if you are in on it.

We purchased the model WFC7500VW, 24” washer and accompanying dryer in June of 2015. Within a couple of months, the water pump went; also we continually had to take the front panel off and clean out the filter when we get an A11 code! Now we experienced an F06 code... This code means the washer can’t go into high speed. The repairman (Whirlpool recommended), told us that a new tachometer motor, etc would run $500-$800 with labor! He also said that the noise the drum made was bad. My dryer works fine (only complaint is the grinding noise it makes, which Whirlpool told me is normal)... I would like to purchase a new washer, but don’t know what will fit under the dryer. I do not want ANY Whirlpool product!

We purchased a cabrio washer about 3 years ago and have had trouble with coins getting into the drain pump and cracking it. We have repaired this at least 5 times and dont understand why the washer allows this to happen. Yes we do accidentally leave coins in our clothes but we have not had this problem with other washers. Clothes also have odor.

Two water heaters three yrs old that went kaput. Thankfully, they are under warranty. However, the tech that I called out said that his company doesnt work on Whirlpool because they are junky and they try to blame the tech if something doesnt work. I called to get new part, and of course now, I get to pay for labor. The lady on the phone actually suggested that I hire an electrician and replace a breaker instead of receiving parts for Whirlpool. Unbelievable. Needless to say, I echo all of the same concerns as the other posts. Im done with Whirlpool.

We have had this dishwasher since 1983 and we still run it on an average of 6 days a week. Features are the fact that it has given all of our dishes, our silverware, our pots and pans sparkling clean looks for all those years. It fits nicely into the kitchen space which was designed for a dishwasher. It never needed a repair. After all those years, this machine still looks fine. After all those years I really doubt if it still has a warranty and it never needed service.

My Whirlpool microwave has been great. Just the right size for my family, with enough settings that it wasnt complicated to use. I found it was very useful with different recipes that I liked to make. I always used it whenever possible to cut down on my cooking time because time is something we dont seem to have enough of. I have baked a lot of different items in my microwave, chickens, all kind of casseroles, cakes. You can even scramble eggs in this one!! It keeps dishes warm until you decide to serve it which is a plus because all microwaves do not have this option. I believe you will enjoy it too!

Not even 3 years ago I purchased the very large capacity (5.0 I believe) Cabrio Whirlpool Washer and Dryer top loader set for my family. I have regretted the purchase since the first week. The washer would CONSTANTLY beep during a wash cycle, stopping the process saying it was unlevel. We made every attempt to make sure the load was even all around the basin and that the machine itself was level itself. No matter what we did, it would need to be restarted numerous times during one wash cycle taking sometimes hours to do one load. VERY FRUSTRATING. Now the washer will turn on, but it will not fill with water or start the cycle at all.The dryer has cost us hundreds of dollars in repairs, bringing the repair man to our house on a weekly basis for a while. Every time needing a new part. I have made a complaint on the Whirlpool USA Facebook page letting them know my absolute frustration as a substantial amount of other people have, and every one of the other complaints receives a comment back but mine. Although their complaint got a generic response such as, Im so sorry for your frustration, please email to the address below and we can look into your issue.I called customer service a few times to see if they could help in anyway...even asked if they could supply the parts if I paid for labor, and the answer was a flat NO. Nothing...I paid just about $2500 for this set and about $400 in repairs, and no help and no apology for selling me appliances that have not lasted even a small percentage of my last set that lasted throughout my teenage years into my 30’s. I am severely disappointed and ready to take action more now for the disrespect I feel as a consumer. I do not recommend Whirlpool Appliances AT ALL any longer...as they used to be a household item in every family member’s home. Now my large number of family and friends all know my frustration and will not purchase Whirlpool. I suggest this company do something to redeem themselves, because this is just ridiculous. No one has money to throw away like this. Thank you.

The beat goes on. My Cabrio washer is still down. After working for a mere 14 months, the control board died, and the machine would not spin out water. The repairman ordered a new one. Though the part arrived several days earlier than predicted, the repair service said they could not send anyone out, until our scheduled appointment. At last, today, the repairman arrived. I am ready to start whittling down the mountains of laundry we have stuffed in every closet. Some areas of my house are starting to smell like a locker room. It is not convenient for us to haul everything to a laundromat, or impose on a relative who lives nearby.The repairman was in the laundry room for at least 45 minutes, and then very apologetically tells us that the part is bad. It will not work at all. He has ordered a new one, and requested rush service, which I think they will ignore. I cant help but think these parts are manufactured somewhere outside the USA. Well, listen to this Whirlpool, I would rather pay $25 more for this part, and have your washing machine work. Dirty laundry might seem unimportant to you. It is not unimportant to us! If you cant do better than this, make something else. I am furious, and will spread this news to everyone I know, and I will report on this situation again.

Same problem a lot of people have written about in your forum. Purchased a double door stainless steel refrigerator, bottom freezer, # GX2SHBXVY from Sears Canada on 12/17/2011. Warranty expired December 2012. Now we have ice forming on the floor under the bottom freezer though water hasnt seeped out as we are now cleaning it daily. Sears wants to charge $75 per hour + parts as there is no extended warranty. Whirlpool says its a common problem with most other Competitor models too. REALLY, ITS NOT. Have checked with a lot of friends of mine with similar models. Nobody is having a problem with especially units hardly one and a half years old. My bro-in-law also bought a Whirlpool a year prior to mine. He is having no problems. See no reason to spend $300-$400 on a comparatively new unit. Also have a 7-month-old stainless steel Whirlpool dishwasher and 4-year-old Gold Accura cooking range. Now spend morning and nights looking at them wondering when they are gonna blow. Need to replace my washer/dryer too but guess which brand I am not opting for.

Model # WMH 1163XVQ-1 manufactured 2010 however I purchased and installed it in July 2011. Noticed a small crack at the base of the handle about a year later. Within the past couple of weeks cracks are appearing everywhere including around the handle, the entire exterior frame as well as interior frame of the door. Neither my wife nor I slam the door or mishandle it to cause this damage. Called Whirlpool this week. Bottom line is that it would cost nearly as much to get a new door as to buy another microwave. This is an over the stove model. My previous microwave was GE and lasted over 15 years. Wont buy Whirlpool again.

My son purchased a Whirlpool washer and dryer as a Christmas gift on 12-24-10 from Sears. It didnt wash the clothes properly and I would have to rewash them. Also, it would not spin the cloths properly and the top would take forever to unlock. Then in July, I called for repair because the water would not spin out at all. It took at least two weeks for them to come out. Another two weeks to get the part they ordered then to find out that they also needed another part that was not diagnosed in the first place. After another three weeks had gone by and having to go to the laundry to wash our clothes several times, it was finally fixed. I continued to have problems with the clothes not getting cleaned. How can this possibly be an energy efficient product when you have to do the load twice? I am so grateful to my son for the gift but am so dissatisfied with the product. I rate this product 1 out of 5 stars.

Whirlpool Cabrio Washer and dryer. Bought the Cabrio Washer. Worked great for 26 months. Had to throw it away. Main motherboard went. Not worth fixing. Called Whirlpool. They offered a $340.00 service contract only. Piece of garbage. Do yourself a favor. Do not go by looks. Its junk.

We purchased 29.7 cu. ft. side by side in February 2013. Ever since we got it, there is an excessive amount of moisture that builds up in the refrigerator section. It is to the point that the bottom shelf must be dried every other day; otherwise water spills out the front. Most of the moisture forms around the cold air duct work leading in from the freezer. We placed collection containers under the duct work which helped a little. We also tried various temperature settings, still no help. We tried online support and were given many excuses for the excess moisture. Support advised to change the defrost cycle, which we did and failed to correct problem. Support finally threw up their hands and said to call for service. Unfortunately, we were advised since the unit was purchased in Florida and shipped out of the country, the warranty was void. Try and get service in the Bahamas! Ha! This will be the last Whirlpool product we will ever buy.

I have had my machines for years, and always buy Whirlpool. So far so good, had to replace my washer and dryer approx 11 years ago and still ok no problems yet. Wish I had the money to buy one of those bigger ones someday.

Ive had so many problems with this washer. Everything has been replaced on the machine and it is still a failure! It has overflowed 5+ times. Stopped draining 4 times (fun getting water out of it...). Have been without a washer for a total of two months! My In-Laws have the same and theirs hasnt been a problem (however it isnt used as much as mine.). Hopefully mine is just a Lemon! Ill never buy another one!!!!! Especially from Lowes. They deem it only a lemon if it has had the same issue for 4-5 times. That is with the extended warranty! TO THE DUMP IT GOES!

Recently bought a 19-cubic ft French Door Whirlpool refrigerator. Seems to work fine at this point, but the compressor/cooling system has a fairly loud swishing noise it makes off and on during the cooling cycle. According to the owners manual, this is normal. If I had known this, I would not have bought this brand. Believe me, it is loud and you can hear it from all parts of my apartment. Also, once you examine the fridge up close, it really is cheaply made. Low-grade plastics for shelves and compartments. And this was not an inexpensive product to buy. We are talking out the door paying $2,000. Sad it is American made. My parents bought a Samsung last year and it is of much higher quality than the Whirlpool I have. But so far, it is keeping the food cold. Just wish it was quiet.

I bought a Whirlpool fridge in June of 2014 and the plastic part of the stainless steel handle that attaches it to the fridge broke about a month or so later. After replacing the fridge because the company said they no longer made the part they gave me a new fridge and with that one the door would not close without leaving a gap of about 1/3rd of an inch open at the hinge side. They took that fridge back and sent me a new fridge. A week later I got in the mail a handle for the first fridge which I no longer had. About a week after that I noticed that the latest and third fridges handle had a crack in the same place. Whirlpool sent me 5 replacement parts and they were all defective with the same crack visible in the replacements. Finally I got a replacement handle that looked good and it broke today, Feb 6th 2016, in the same place as the first one. I should mention that each time the company replaced the fridge it was with a different and better model and each with a slightly different handle. There are other design flaws with the fridge. The door is in a corner and there are cabinets on the wall so the door can only open slightly more than 90 degrees which makes it impossible to open the crisper drawer enough to get a cabbage in it and if I want to clean the crisper drawer I must move and turn the fridge in the kitchen. Also if the crisper drawer is not closed completely it causes the guard rail on the bottom door shelf to fly off sending everything on the bottom shelf to fall to the floor. Fun when some are made of glass and filled with liquid. You would think I would have learned my lesson about this company but no! I went to Lowes and bought a Whirlpool dishwasher and when I saw that the automatic door would not open enough to dispense the soap, powder or packet I called a certified Whirlpool repairman who told me after receiving a duplicate that of course would not work either, that there was no solution to the problem and I went back to Lowes and bought a Samsung and my problems were solved. I WILL NEVER BUY ANOTHER Whirlpool or as I now call it, Whirledpoo, product, EVER.

The refrigerator has excellent quality, low noise level, clean lines and enough room for produce and frozen foods. Would recommend this to friends. This replaces a Whirlpool refrigerator that was over 30 years old. The original unit still works extremely well and we gave it to a family that needed a refrigerator and they were very happy to receive it. It looked as new as the day I purchased it 30 years ago.

Purchased Cabrio washer in June 2011; in May of 2014 repairman said tub seal was leaking and new bearings were needed at a cost of $400. The washer was still working, but sounded like a freight train, very loud. My trusted repairman said to purchase a replacement, this time with an agitator (the Cabrio has no agitator). 2 additional points : the Cabrio took 63 minutes to wash sheets; other loads required similar long cycles, something they dont mention with new efficient washers. Also, agitators will no longer be manufactured in washing machines within the next 2 years. : (

We bought a small refrigerator/freezer Model WRT112CZJZ for a guest house. When not in use it was turned off at the unit control panel with the doors left open. There was a power failure and when the power was restored the refrigerator turned itself back on. Needless to say it must have been running for 2 weeks with the doors open and the condensation filled the holding tank and then proceeded to overflow on the wood floor. The floor was ruined. There was no indication in the manual to warn of the unit restarting when power is restored so it must be unplugged or the circuit breaker turned off to avoid a similar problem.

I bought a Whirlpool french door refrigerator, model # ED5LVAXWS about five years ago. I didnt have any problems until last month, on August 25, 2016. The ice dispenser stopped working, and the refrigerator went off. I had to throw out a lot of food. I got a new extended warranty that day, and a serviceman came out the following day, 8/26. It turned out he wasnt a repairman, just someone to diagnosis the problem and order the parts. The part was ordered, and the fridge would be repaired within 5 days, but the part was delayed because of a Hurricane Hermine, which completely understandable.On 9/8 the repairman arrived, but he realized that the original guy who diagnosed the problem was in error. He had ordered a compressor, and what needed to be replaced was the thermostat. As of today, 9/29, the part is still not in -- I was told its on backorder with no ETA. If I didnt have a mini fridge, Id be at a complete loss. I called what I thought was Whirlpool to complain about the part taking so long to arrive, but was told they can do nothing. It turns out that a company called AIG U.S. Warranty Division handles Whirlpools guarantees. I am not a happy camper.

I bought at Lowes. The first one was sent back (doors stuck, suction cracked lining). Now the temps are not working in the fridge or freezer. All the food got dumped. Its sad. My old one lasted closer to 25 yrs. (and may I add up to ten children). This one has only been used by adults. I thought I could trust Whirlpool?! I sent info to local Lowes. We will see if theres any help.

After 2.5 years seal around door melted on microwave. Whirlpool Corp sent a repairman to do a safety check. Said unit was ok to use. Plastic seal on for area totally melted about 2 inches wide. Co. Had a recall about a similar problem but our serial number was not included???? Did not want to give them any stars.

We Purchased our KitchenAid refrigerator from Home Depot. After 1 week we had issues with the ice maker, water dispenser and lights going on and off randomly. Technician comes 5 days later, he half way fixes it and discovers we need to order a part. The part took over a week to get and by the time he shows up to fix the refrigerator, it has now been TWO WEEKS with out our $4,000 refrigerator not working properly. Well, after trying to replace the part and spending 45 minutes on the phone with some engineer, it still wasn’t fixed. He Says to us “hey good news youre getting a new refrigerator”. Good news my **. It’s now been THREE weeks and it turns out the new one isn’t coming for another week. Customer serves reps. are really good at apologizing for the inconvenience but Whirlpool has Done NOTHING to composite us. DO NOT BUY WHIRLPOOL.

I bought this Whirlpool Cabrio washer three and 1/2 years ago and the assembly which is basically the transmission and the assembly which is the agitator is out! Needs replaced! This is complete crap! The new parts will costs over $500 bucks plus labor! Ridiculous! My last washer which was a Maytag lasted me 20 years! What a piece of junk! Now I have to. It a new washer! No thanks to you Whirlpool! I will never buy another Whirlpool appliance again! Neither will my family or friends!

The exterior look of the refrigerator (WRX735SDBM00) is impressive and the stainless steel does not show finger prints easily. It has two french doors on top, a middle drawer, and the freezer drawer on the bottom. The interior is 25 cf, but there isnt much space, even with reconfiguring the shelves, and the crisper/meat drawers are so small, that a large bell pepper wont fit. When one French door is closed it pops open the other door, which then does not close back tightly. Although there is an alarm system to warn a door is open, it only works if the doors are open and not just cracked. We have to constantly push on both doors to be sure they are closed tightly, even after washing down the gasket to get a better seal.

Whirlpool Cabrio Platinum Option - Very stylish. Well built - very solid and heavy constructions. Full features from quick wash to sanitary wash, very energy efficient, steam setting on dryer for touch-ups. Quick loads, etc. We were looking for a washer and dryer set that would accommodate large quilts and blankets and still have the flexibility to handle small and delicate loads, and be energy efficient. The Whirlpool Cabrio Platinum Option is solidly built and very sturdy. It handles small and large loads and is very energy efficient. Both the washer and dryer handle sheets and pillowcases without a problem. Wed recommend them to anyone.

The appliances in my home range from a Kitchen Aid double wall oven, a DCS single wall oven (I have 2 Kitchens), 2 Kenmore dishwashers, a Fisher and Paykel refrigerator and 2 DCS counter-top stoves (all top of the line). No problems they are great appliances. On Dec.22, I bought a Whirlpool Duet. For 6 months, constant repairs and rebuilds were needed; new computer panels, pumps and new drums. They cant fix it. We have tried everything to get the Whirlpool Factory to fix it or replace it. So far, I have spent twice the original cost to fix the machine (but to no avail) and now you want me to spend another $500-$600 to try to fix it again? No more!

Purchased a brand new Whirlpool hot water heater, but it has never worked properly. The 1-800 help line has been no help at all. Every call results in another step we have to complete before they can fix the problem. Bottom line - never, ever, ever buy a Whirlpool product. They dont know the meaning of customer service.

I have had this refrigerator for 23 months. The ice maker has been a continual problem. It overfills and water runs onto my hardwood floor. After four service calls for the ice maker, the defroster heater caught on fire and melted the interior wall of the freezer. Not sure if we fixed the ice maker since we had the fire four days after the last service call. My service rep declared the refrigerator unrepairable. Fortunately I had purchased an extended warranty and they refunded 85% of the purchase price after 2 years of use. Besides the ice maker problem and the fire, I also had trouble with food freezing in the refrigerator compartment. I dont recommend this model, but my repairman says that Whirlpool is as good as it gets.

Whirlpool washing machine model WCW4950XW2 - We have a barely two year washing machine that we purchased at Best Buy and it no longer drains or spins. After $100 repair call we were told that this is a common problem with this model. It is a transmission problem, and with the way the machine is built a repair person cannot get into the transmission to fix it. He suggested we buy a new washing machine. This is a travesty on so many levels! If whirlpool know it has a problem it should offer a partial refund for the purchase of a newer better machine. I keep thinking about what our landfill in this world look like with the proliferation of appliances that are engineered to last a year or two. I can guarantee you I will never purchase any Whirlpool produce again, and I will research whether other brands are associated with the whirlpool brand before I buy it. Sad that a once good company has gone to hell.

We bought a side by side refrigerator/freezer in 2013 from our local Best Buy. We have usually bought Whirlpool appliances. Before we bought this refrigerator the last Whirlpool we had for 25 years. This past week our refrigerator went out. We called a repair man. He said the circuit board was out and would cost $450.00 to replace it. We decided to buy a new one. I am very disappointed that it only lasted 7 years. Oh I forgot to mention the ice maker went out about a year ago. We did get new filters as instructed. We did not buy another Whirlpool.

I just wanted to post a quick response to a problem that so many people are having with their Whirlpool FG1H5040T3NOV Hot Water Heater. The biggest problem is the Pilot Light Wont Stay Lit. Ive had this water heater for many years now (since 2005) and two days ago we didnt have any hot water. I checked the heater and found that the pilot light was out and that when I lit the pilot light with the igniter, it wouldnt stay light. This could have been a number of problems causing this issue but heres what I did to get it fixed. I looked around on the internet and saw that many people had this same problem and several years ago Whirlpool gave out warranty replacement upgrade kits to fix it. I called Whirlpool support, gave them my serial number and mentioned the upgraded kit. Unfortunately, my 9-year warranty expired a few months ago and I am no longer able to get the upgrade kit for free. Apparently this upgrade kit was part of a settlement for this water heater that was sold through Lowes. The upgrade kit has a few enhancements including an adapter to allow the use of a standard right hand threaded thermocouple as well as a larger pilot light window and added safety thermal switch. This is definitely an improvement over the old.Anyway, I looked at Lowes website for this upgrade kit and their description and internal part number is slightly different but it is the same thing as confirmed by Whirlpool. Whirlpools part number is 6910813 for the conversion kit. Lowes calls this part American Water Heater Company Gas Enhancement Kit 5040T NG. This kit is only $35 which isnt bad. So, I went to Lowes, purchased the kit. The instructions are included and are even good for a novice. It took me about an hour to complete the changeover. Youll need to remove the old burner and orifice to use them on the new kit. I then checked for gas leaks. I lit the pilot and when I turned on the heater, the burner lit right up. All is good now!

Bought this brand new 5 door fridge, not even 2 years ago and had nothing but problems. Computer went 2 times. Rail broke for the drawer in freezer. Freezing up in freezer. Switch on freezer drawer went out. I will never buy anything else from Whirlpool again. So much for the nice looking things.

Bought a whirlpool refrigerator in 2015, have had both handles replaced 3 times, the bottom pieces of the handles are made of plastic and they crack. We had to take them to a metal fabricator and have them replaced with metal to keep them from breaking. Lowes and whirlpool know of this problem and they do nothing about it. Will not buy another whirlpool product. Very dissatisfied.

We own a Whirlpool microwave hood combination. The door started cracking where the handle attaches. Ordered a new door and installed in July 2017. 18 months in the door and the handle have both started to crack again. This seems to be a problem with Whirlpool microwaves but they wont stand behind their product. Theyll send someone out to replace it for $$$$ but they wont admit they have a flawed product. One year warranty - no exceptions. Will have to replace the microwave and it wont be Whirlpool!

We had purchased an 80-gallon hot water heater less than five years ago. The tank started leaking, so the whole hot water heater had to be replaced. The previous unit we had was at least 10 years old, if not more. We are extremely displeased with the quality, and very upset with having to outlay such a large amount of money within five short years. Whirlpool has certainly not earned our trust in their workmanship.

Bought a new $899 dishwasher 7/2020 and it stopped working 10/2020 And it’s been weeks and now I’ve been told it will be another 21 before they can replace it if at all! #whirlpoolusa #whirlpoolcorp Customer service lady was rude with an attitude.

I bake a lot so my husband bought me a new gas range for our 54th anniversary. After the first few times I used the oven, I decided to clean it. I noticed then that there were some burnt grease spots and streaks between the oven glass door. After 2 years of use, it has gotten much worse so I decided to take the door apart to try to clean the glass in between the layers of glass but there are three instead of two. I cleaned the inside of the outer glass, but that didnt take care of the problem. Most of the stains are between the other two panes of glass. That, I cant get to. I feel that this is poor design and not sealed properly. I take good care of everything I own and I expected this range to last me the rest of my life but it is put together with cheap plastic parts that wont last long. It is the first new range that I ever owned and paid a lot more for it than any Ive had. I expected better.

On 11-29-2014 we were washing our laundry and our whirlpool washing machine started making a really loud noise so I went to investigate the problem. I open the bottom part of the washer to find out that the whole cement block to balance the drum was on the floor of the washer so I called the 1800 number on the machine and no one at whirlpool corporation wanted to even help. No one said sorry. No one said Let me see if I can help. No one. Every one I talked to they cant help at all. No one apologized once about the poor product that whirlpool sells and the defect that their products has. My washer is one year and one month old. So I can say truly with confidence that whirlpool product are the worst in the world plus their customer service even more. It is very sad after we paid all kind of money for our washer now I have to buy another one after one year and one month. Very bad customer service.

We bought a duet washer and dryer about 3 1/2 years ago. In that time, we had many error codes that we had to research online and fix. We have replaced many things to date. However, this last code,F70, has really been the last straw. Basically you are better off buying a new washer and staying away from Whirlpool. We had a company tech come and diagnose the washer. This code says that its the interface board. The company has replace this board 3 times and the code is still coming up. They have basically replaced everything in our washer and the code remains the same. Nothing is fixing it. They have had Whirlpool-certified employees come in to look at the washer and are unable to fix it as well. They have been trying to fix it for 2 months. I called Whirlpool corporate office and they informed me that the company that we went with is not Whirlpool-certified, therefore the only thing they will do is either give us 15 % of our money back if we were to by a new washer, or we can have a certified dealer come out and diagnose it again. Well, that is just a waste of time. We already know whats wrong with it and would have to pay again to have it diagnosed or we totally loose a lot of money. I feel that Whirlpool really should stand behind their products, considering the price tags they have on them. They should last much longer than 3 1/2 years. I will not by another Whirlpool product again. Apparently, Whirlpool doesnt seem to care about loosing customers. I dont feel that they deserve any stars but it doesnt allow to pick a negative number.

After 2-1/2 years we started having trouble with the spin cycle on our Maytag washer. We live in an area with no repairman. Whirlpool want us to pay just to talk to us. Now the timings off. It will not spin out.

I purchased a house with Whirlpool products installed. The refrigerator wasnt too cold but working for the first 2 months. Then the ice maker stopped working, the freezer stopped working and now nothing works. I have been through 4 service calls, I repaired that took almost 2 hours and the refrigerator is still not working. I have spoken with numerous Whirlpool representatives and they were like robots with respect to their response. There is a chain that they adhere to and once you have spoken to an executive at their corporate office, no one else can help you. Now I am trying to reach that executive and there hasnt been a response. I havent been able to have food in my refrigerator for over 3 weeks and counting. Imagine, eating out for breakfast, lunch and dinner for this length of time. Christmas - no refrigerator, New Year - no refrigerator. A consumer who makes a purchase in good faith should not be put to this kind of agony while trying to remedy the situation. I dont know what happened to their customer service but it is nil. From my own personal experience and in my opinion, Whirlpool is not a company that cares about their customers, just their profits. I am at a loss . What are my options as a consumer?

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

I bought Whirlpool Dishwasher from Lowes. This is just 2 years old. Model number is WDTA50SAHZ. This is gently used Dishwasher. Suddenly it stopped working. After water fill up, dishwaher is not working. I thought whirlpool is superb brand. Now its waste brand. Do not buy whirlpool dishwasher.

The repair technician just left telling us that our Whirlpool Cabrio washing machine is fine. It is a little over a year old, makes LOUD noises as it runs, doesnt get the clothes clean and often doesnt even get them wet. The clothing sits above the water and comes out with pet hair, soap and dry spots. We use it the way the manual directs but it seems to be a totally defective machine. We sure wouldnt sell it to anyone nor give it away to some poor unsuspecting soul. Guess it needs to go to the dump. Shame on you Whirlpool for taking advantage of so many of us.

We will never, I repeat, never buy another Whirlpool, Kitchen Aid or Maytag (other than the Maytag dishwasher) product again. After just two years on the Cabrio washing machine, the bearing on the wash tub began to go out. As it was out of warranty, the cost to fix was greater than just buying a new machine. This was a known problem and Whirlpool failed to remedy the problem. Based on this experience, we went with an LG as a replacement. Before you buy anything, research it.

We purchased the Whirlpool Cabrio washing machine around January 2006, and from the start weve had nothing but problems with this appliance. Within the first year, water was leaking under the washer which was coming from a crack in the plastic housing of the water pump. I replaced the pump myself to save on labor. No big deal. The very next year, I started getting the F51 code and there was no way for me to get around calling a service company to have it repaired. $350 and one circuit board later, it was repaired. It remained working without fail until recently when it began giving the same F51 code. Let me guess, another $350 for better repair? I have to assume that the new circuit board that was installed wasnt any better than the original one that was replaced. I wouldnt put another $1 into this hunk of junk and Whirlpool should be ashamed to have this product on the market. I will never buy another Whirlpool product.

Do not buy anything from Whirlpool. This company needs forced out of business. Everything breaks down within weeks or months. I bought a fridge, dishwasher, and a washer dryer. Within 16 months they all went to the trash.

I feel Whirlpool has a terrific portable dishwasher. I really like the way it is set up and it is a very nice looking unit. They could improve on their customer service towards their customers. My dishwasher got a crack in it at the top of the door where you open it and they would not send anyone out to fix it for me. I paid a pretty penny for this dishwasher and felt they should have fixed it for me. This happened in the 1 year warranty period. Otherwise I am very happy with it. I had previously had another one that lasted me 14 years.

I purchased this fridge in February 2015. In August, the handle on the fridge door broke. I called for a replacement on 8/7, on 9/14/15 I received it. It broke on 10/3/15 and had a replacement on 10/13/15. It broke again on 12/26/15. I called for a replacement. I should get it in 10 days. Obviously, there is a flaw in their design. What bothers me is that no one seems to care. I will hope I never have to buy a Whirlpool product again. And I will certainly discourage anyone I know who is thinking about buying their products. I purchased this product at Lowes and they did not care when I went to them.

My dishwasher is more than 10 years old. It functions but the interior baskets have broken and because my counter overhangs a couple of inches from the dishwasher the steam from the dishwasher has damaged the underside of the counter. It cleans ok but I would not buy this kind of dishwasher again.

We purchased a top of the line (we thought) Whirlpool stainless dishwasher 15 months ago from HHGregg. All was fine until 2 weeks ago - it produced a burning smell and was making a funny noise. We had it looked out. The motor is burning out. I called Whirlpool and explained the issue. There is nothing they can do. It is over 12 months. Really? They cant stand behind their product? I understand if it was a small part or such but an entire motor burning out in just over a year? I know that not all products can be perfect, some times mistakes slip through the line. I guess it was silly of me to expect a company in todays age to stand behind their name and product. Obviously, with this company, it is buyer beware.

I purchased the Whirlpool Cabrio HE top loading washer and front-loading dryer about 7 years ago. It has been okay, but nothing special. Recently it began stopping in the middle of the cycle and showing an F51 error. Then all of a sudden the noise during spin was deafening. Brought out a tech, who came and did some eval. Left with some basic maintenance. Did a load, and happily no more F51 code, but still so very loud during spin cycle.Called again; tech returned and said that drum and shaft would likely need to be replaced to the tune of some $500. The same story as others have told. We should have bought the extended warranty. Like others, I also felt that washers lasted at least 10 years. And that seemed a short time given expectations in the past of 20 years of service. Im disappointed in Whirlpool. Even though Consumer Reports gives the Whirlpool Duet washer (new 2013) one of its highest reviews, I cant bring myself to buy another Whirlpool product. It appears to me that this warrants recall as well.

After 50+ years of doing laundry, I had to purchase my 3rd washer. I bought the new top loader without an agitator. I very quickly learned that it has no lint filter. My first load was towels and mats. The lint clogged up my tub and drain pouring water all over the floor. Since then it has ruined many of my clothes which are mostly sweaters and sweater-knits. Without a lint filter, it deposits the lint right back on the clothes where it stays forever unless I shave or pick it off, even though Ive turned them inside-out. (Time consuming waste!) Even my socks have little balls of lint. It seems the only safe fabrics are new, smooth woven cottons, cotton-blends and slippery nylon providing there is no lace or brushed elastic.Now to the no fabric-softener dispenser... The Downy ball simply doesnt work, and theres no other way to add it. Waiting to use dryer sheets is too late; the damage is done. My clothes are dingy. In my 50+ years of ownership, I have never had to purchase a separate product to wash my washer so that it doesnt stink... and it does. Why does it lock after starting? If I could afford to replace it, I would... but I cant.